Wave is a common environmental load that often causes serious damages to offshore structures. In addition, the stability for the submarine artificial slope is also affected by the wave loading. Although the landslide of submarine slopes induced by the waves has received wide attention, the research on the influence of solitary-wave is rare. In this study, a 2-D integrated numerical model is developed to investigate the stability of the foundation trench under the solitary wave loading. The Reynolds-Averaged-Stokes (RANS) equations are used to simulate the propagation of a solitary wave, while the current is realized by setting boundary inlet/outlet velocity. The pore pressure induced by the solitary wave is calculated by Darcy’s law and the seabed is characterized by Mohr-Coulomb constitutive model. Firstly, the wave model is validated through the comparison between analytical solution and experimental data. The initial consolidation state of slope under hydrostatic pressure is achieved as the initial state. Then, the factor of stability (FOS) for the slope corresponding to different distance between wave crest and slope top is calculated with the strength reduction method. The minimum of FOS is defined as the stability index for the slope with specific slope ratio during the process of dynamic wave loading. The parametric study is conducted to examine the effects of soil strength parameters, slope ratio and current direction. At last, the influence of upper slope ratio in a two-stage slope is also discussed.

The non-inertial effects on spin-0 scalar particle that interacts with scalar potentials of Cornell-type in cylindrical system and Coulomb-type in the magnetic cosmic string space-time using Kaluza-Klein theory is analyzed. We show that the energy eigenvalue and eigenfunction depend on the global parameters characterizing the space-time, and the gravitational analogue of the Aharonov-Bohm effect for bound states is observed.

Extracorporeal shock wave therapy (ESWT) is a well investigated and widely used treatment modality for a number of musculoskeletal disorders. A limitation of ESWT is its potential painfulness at higher, clinically relevant energy flux density (EFD), which may limit its applicability and, thus, effectiveness. Various studies in the literature demonstrated that neither application of a higher number of extracorporeal shock waves with lower EFD nor use of local anesthesia may solve this problem. Based on the results of several other studies in the literature it is hypothesized here that in patients suffering from musculoskeletal disorders that can be treated with ESWT, pretreatment with a pulsed, high power laser with a wavelength of 904 or 905 nanometers (hereafter: "laser pretreatment") does not only allow to apply higher EFDs in subsequent ESWT but actually results in faster and/or better treatment outcome than ESWT without laser pretreatment. Accordingly, it is hypothesized here that combining ESWT with laser pretreatment leads to synergistic effects and, thus, is superior to either treatment modality alone. Confirming this hypothesis in preclinical and clinical research may raise significance and increase the use of ESWT in physical and rehabilitation medicine, with immediate benefit for patients.

In this paper, a high-performance antenna array system model is presented to analyze moving-object-skin-returns and track them in the presence of stationary objects using frequency modulated continuous wave (FMCW). The main features of the paper are bonding the aspects of antenna array and electromagnetic (EM) wave multi-skin-return modeling and simulation (M&S) with the aspects of algorithm and measurement/tracking system architecture. The M&S aspect models both phase and amplitude of the signal waveform from a transmitter to the signal processing in a receiver. In the algorithm aspect, a novel scheme for FMCW signal processing is introduced by combining time- and frequency-domain methods, including a vector moving target indication filter and a vector direct current canceller in time-domain, and a constant false alarm rate detector and a mono-pulse digital beamforming angle tracker in frequency-domain. In addition, unlike previous designs of using M×N fast Fourier transform (FFT) for an M×N array, only four FFTs are used, which tremendously saves time and space in hardware. With the presented model, the detection of the moving-target-skin-return in stationary objects under a noisy environment is feasible. Therefore, to track long range and high-speed objects, the proposed technique is promising. Using a scenario having 1) a target with 17 dBm2 radar cross section (RCS) at about 40 km range with 5.93 Mach speed and 11.6 dB post processing signal to noise ratio, and 2) a strong stationary clutter with 37 dBm2 RCS located at the proximity of the target, it demonstrates that the root-mean-square errors of range, angle and Doppler measurements are about 26 meters, 0.68 degree and 1100 Hz, respectively.

This study demonstrates the orientation and the ‘shape factor’ have pronounced effects on the development of the localized pressure fields inside of the helmet. We used anatomically accurate headform to evaluate four modern combat helmets under blast loading conditions in the shock tube. The Advanced Combat Helmet (ACH) is used to capture the effect of the orientation on pressure under the helmet. The three modern combat helmets: ECH, Ops-Core, and Airframe, were tested in frontal orientation to determine the effect of helmet geometry. Using the unhelmeted headform data as a reference, we characterized pressure distribution inside each helmet and identified pressure focal points. The nature of these localized “hot spots” is different than the elevated pressure in the parietal region of the headform under the helmet widely recognized as the under-wash effect also observed in our tests. It is the first experimental study which indicates that the helmet presence increased the pressure experienced by the eyes (as evidenced by the pressure sensors in the H8 and H9 locations), and the forehead (denoted as H1 location). Pressure fingerprinting using an array of sensors combined with the application of principle component analysis (PCA) helped elucidate the subtle differences between helmets.

Design criteria for coastal defenses exposed to wave overtopping are usually assessed by mean overtopping discharges and maximum individual overtopping volumes. However, it is often difficult to give clear and precise limits of tolerable overtopping for all kind of layouts. A few studies analyzed the relationship between wave overtopping flows and hazard levels for people on sea dikes, confirming that one single value of admissible mean discharge or individual overtopping volume is not a sufficient indicator of the hazard, but detailed characterization of flow velocities and depths is required. This work presents the results of an experimental campaign aiming at characterizing the flow characteristics associated to maximum individual overtopping volumes for an urbanized stretch of a town along the Catalan coast, where a walking and bike path and a railway run along the coastline are exposed to significant overtopping events every stormy season. The work compares different safety criteria for pedestrian. Results prove that safety of pedestrian on a sea dike can be still guaranteed even for overtopping volumes larger than 1000 l/m. Pedestrian hazard is rather proved to be linked to the combination of overtopping flow velocity and flow depth.

Layered 2D graphene oxide (GO) films are integrated with silicon nitride (SiN) waveguides to experimentally demonstrate an enhanced Kerr nonlinearity via four-wave mixing (FWM). Owing to the strong light–matter interaction between the SiN waveguides and the highly nonlinear GO films, the FWM performance of the hybrid waveguides is significantly improved. SiN waveguides with both uniformly coated and patterned GO films are fabricated based on a transfer-free, layer-by-layer GO coating method together with standard photolithography and lift-off processes, yielding precise control of the film thickness, placement and coating length. Detailed FWM measurements are carried out for the fabricated devices with different numbers of GO layers and at different pump powers. By optimizing the trade-off between the nonlinearity and loss, we obtain a significant improvement in the FWM conversion efficiency of ≈7.3 dB for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. We also obtain a significant increase in FWM bandwidth for the patterned devices. A detailed analysis of the influence of pattern length and position on the FWM performance is performed. Based on the FWM measurements, the dependence of GO’s third-order nonlinearity on layer number and pump power is also extracted, revealing interesting physical insights about the 2D layered GO films. Finally, we obtain an enhancement in the effective nonlinear parameter of the hybrid waveguides by over a factor of 100. These results verify the enhanced nonlinear optical performance of SiN waveguides achievable by incorporating 2D layered GO films.

This work focuses on expressing the TSP with Time Windows (TSPTW for short) as a quadratic unconstrained binary optimization (QUBO) problem. The time windows impose time constraints that a feasible solution must satisfy. These take the form of inequality constraints, which are known to be particularly difficult to articulate within the QUBO framework. This is, we believe, the first time this major obstacle is overcome and the TSPTW is cast in the QUBO formulation. We have every reason to anticipate that this development will lead to the actual execution of small scale TSPTW instances on the D-Wave platform.

Background: This research presents the use of photoplethsmography combined with Traditional Tibetan Pulse reading for the estimation of the three energies of a person: Activity, Transformation and Stability. The growing interest to revive traditional finger pulse reading attests of the need to find alternative ways to approach complex multi-source diseases as well as individualised diagnostic wearable or portable cost effective systems. Method: Our work is presented in two studies. The first study presents the development of the technique of photoplethsmography to classify the three energies. The second study presents a validation of this methodology on mental stress and relaxation. Results: Energies classification achieved a sensitivity above 85% and specificity above 72%. Mental stress and relaxation could be significantly discriminated from baseline condition. Harmonic analysis gave further insights into the dynamic of the pulse wave under stress/relaxation. Conclusion: The photoplethsmogram contains information pertaining to the mental and physiological state of a person as interpreted with the Eastern energies concepts. The implication of this work points towards a holistic understanding and impact of human activities, health and its environment.

The present paper deals with the stochastic modeling of bio-colonization for the computation of stochastic hydrodynamic loading on jacket-type offshore structures. It relies on a multidisciplinary study gathering biological and physical research fields that accounts of uncertainties at all the levels. Indeed, bio-colonization of offshore structures is a complex phenomenon with two major but distinct domains (i) marine biology whose processes are modeled with biomathematics methods and (ii) hydrodynamic processes. This paper aims to connect these two domains. It proposes a stochastic model for the marine organism’s growth and then continues with transfers for assessment of drag coefficient and forces probability density functions that accounts for marine growth evolution. A case study relies on the characteristics (growth and shape) of the blue mussel (Mytilus edulis) in northeastern Atlantic.

An evanescent wave is a non-propagating wave with an imaginary wave vector. In this study, we prove that these are solutions of the tachyon-like Klein–Gordon equation, and that in the tunneling of ultrarelativistic spin-1/2 particles they describe superluminal states arising from interactions between a particle and barrier. These states decay as a particle emerges from the opposite side of a potential barrier, conserving the same initial energy but not necessarily the same mass. The obtained theory is applied to the neutrino, to explain flavor oscillations during free flight and determine the conditions that maximize the probability of their occurrence.

InGaN/GaN samples grown on c-plane sapphire substrate with different In concentrations by metal organic chemical vapor deposition are demonstrated. The subsequent capping GaN layer growth opens a possibility for dislocation reduction due to the lateral strain relaxation in growth geometry. We present the further growth optimization and innovative characterization of InGaN layers overgrown on different structures with varying In concentrations. The photoelectrical and optical properties of the InGaN layers with or without capping GaN layer were investigated by time-resolved picosecond transient grating and temperature dependence photoluminescence. We note a 10-fold increase in carrier lifetime in the InGaN layers when the sample structure changes from PIN to single InGaN layer.

Phenomenon of vacuum fluctuations of virtual particles in high energy physics has been mathematically modeled by a third order differential equation. Aim of present theory is to unravel underlying mathematical equation capable of explaining microscopic phenomenon of vacuum fluctuations. Solution of such a differential equation after applying appropriate boundary conditions gives an acceptable wave function i.e. . Operation of energy and time operator on this wave function proves that these operators do not hold commutative property. Time energy uncertainty principle has been derived by calculating variance of energy and time for the same wave function.

It is well-known that surface plasmon wave propagates along a straight line, but this common sense was broken by the artificial curved light – plasmon Airy beam. In this paper, we introduce a new class of curved surface plasmon wave - the photonic hook plasmon. It propagates along wavelength scaled curved trajectory with radius less than surface plasmon polariton wavelength, and can exist despite the strong energy dissipation at the metal surface.

In this work, a mixture of Elzaki transform and projected differential transform method is applied to solve a nonlinear wave-like equations with variable coefficients. Nonlinear terms can be easily manipulated by using the projected differential transformation method. The method gives the results show that the proposed method is very efficient, simple and can be applied to other applications.

Observed sea surface Ka-band normalized radar backscatter cross section (NRCS) and Doppler velocity (DV) exhibit energy at low frequencies (LF) below the surface wave range. It is shown that non-linearity in NRCS-wave slope Modulation Transfer Function (MTF) and inherent NRCS averaging within the footprint account for the NRCS and DV LF variance with the exception of VV NRCS for which almost half of the LF variance is attributable to wind fluctuations. Although the distribution of radar DV is quasi-Gaussian suggesting virtually little impact of non-linearity, the LF DV variations arise due to footprint averaging of correlated local DV and non-linear NRCS. Numerical simulations demonstrate that MTF non-linearity weakly affects traditional linear MTF estimate (less than 10% for |MTF|< 20). Thus the linear MTF is a good approximation to evaluate the DV averaged over large footprints typical of satellite observations.

In the present work the problem of the attenuation of longitudinal sound oscillations in a conducting medium are considered. The proposed approach is based on the dynamic interaction of electron gas with the lattice vibrations. This interaction is manifested in the modification of kinetic equation for electrons. The process is accompanied by generation of an electric field.

This study aims to provide analyses of the levels of airborne particulate matter (PM) using a two-pronged approach that combines data from in situ Internet of Things (IoT) sensor networks with remotely sensed aerosol optical depth (AOD). Our approach involved setting up a network of custom-designed PM sensors that could be powered by the electrical grid or solar panels. These sensors were strategically placed throughout densely populated areas of North Texas to collect data on PM levels, weather conditions, and other gases from September 2021 to June 2023. The collected data was then used to create models that predict PM concentrations in different size categories, demonstrating high accuracy with correlation coefficients greater than 0.9. This highlights the importance of collecting hyperlocal data with precise geographic and temporal alignment for PM analysis. Furthermore, we expanded our analysis to a national scale by developing machine learning models that estimate hourly PM2.5 levels throughout the continental United States. These models used high-resolution data from the Geostationary Operational Environmental Satellites (GOES-16) Aerosol Optical Depth (AOD) dataset, along with meteorological data from the European Center for Medium-Range Weather Forecasting (ECMWF), AOD reanalysis, and air pollutant information from the MERRA-2 database, covering the period from January 2020 to June 2023. Our models were refined using ground truth data from our IoT sensor network, the OpenAQ network, and the National Environmental Protection Agency (EPA) network, enhancing the accuracy of our remote sensing PM estimates. The findings demonstrate that the combination of AOD data with meteorological analyses and additional data sets can effectively model PM2.5 concentrations, achieving a significant correlation coefficient of 0.849. The reconstructed PM2.5 surfaces created in this study are invaluable for monitoring pollution events and performing detailed PM2.5 analyzes. These results were further validated through real-world observations from two in situ MINTS sensors located in Joppa (South Dallas) and Austin, confirming the effectiveness of our comprehensive approach to PM analysis. The US Environmental Protection Agency (EPA) recently updated the national standard for PM2.5 to 9 μg/m3, a move aimed at significantly reducing air pollution and protecting public health by lowering the allowable concentration of harmful fine particles in the air. Using our analysis approach to reconstruct the fine-time resolution PM2.5 distribution across the entire United States for our study period, we found that the entire nation encountered PM2.5 levels that exceeded 9 μg/m3 for more than 20% of the time of our analysis period, with the eastern United States and California experiencing concentrations exceeding 9 μg/m3 for over 50% of the time, highlighting the importance of regulatory efforts to maintain annual PM2.5 concentrations below 9 μg/m3.

Observation of the distribution of the velocity of galactic rotation curves differed from their expected centripetal form and lead to the notion of Dark Matter or modifications to Newtonian and General Relativity, such as MOND, TeVeS and the like and even Quantised Inertia. We aim to show that General Relativity with Dark Energy/the Cosmological Constant is all that is needed, with the proviso that the Cosmological Constant can increase in the presence of a light flux or some other factor from galaxies and become gravitating; the need for Dark Matter may be abated.

The study was conducted to evaluate the agronomic performance, forage yield, and nutritive values of Desho grass varieties under supplementary irrigation at Dambi Dollo University experimental site, Western Ethiopia. Three Desho grass varieties (Areka /DZF#590, Kindu kosha-1/DZF #591, and Kulumsa /DZF #592) were arranged in randomized complete block design (RCBD) with three replications. The CROPWAT 8.0 model, local climate data, forage data, and soil data were used to determine Desho grass water requirements and irrigation schedules. The agronomic parameters, yield, chemical composition, and in vitro digestibility of the feed samples at standardization cut were determined following the standard procedures. The results showed significant differences (p

Abstract Using the Pauli algebra version of the Dirac equation six symmetric but non-equivalent copies of the QED Lagrangian are constructed. The group of symmetries is the group of outer automorphisms of the finite quaternion group, isomorphic to the group of permutations on three letters. Solutions to corresponding Dirac equations form six sectors of fermion fields. The intersections between different sectors can only contain massless fields, implying that the sectors are distinct. If the symmetry could be extended to the full Standard Model Lagrangian it would predict the ratio of dark matter to ordinary matter of 5 : 1 which is close to the ratio of 5.2 : 1 according to current observations.

The construction industry is notable contributors to atmospheric dust particulate emissions. The particulate matter (PM) produced in construction processes contains a range of chemically hazardous substances, posing significant health risks (HR) to individuals. The occupational health hazards research in construction has become a focal point of interest internationally. Initiated in the early 2000s, there has been a growing demand within the construction research community for the creation of a unified PM database that encapsulates a wide array of construction activities. Previous studies have endeavored to establish a PM database for various construction contexts, yet they have fallen short in thoroughly addressing the diversity of construction materials and the levels of toxic substances (TS) within the PM. This study validates the proof of value that HR associated with construction processes can be measured using PM and TS datasets generated from various work processes using a variety of construction materials. This was accomplished through a semi-automated Building Information Modeling (BIM)-based plugin, which streamlines the assessment of occupational HR in construction projects alongside ongoing work processes. To validate the practicality of the Health Risk Index (HRI) determination via this BIM plugin, a case study on a real renovation project was executed. This system provides construction supervisors with a tool to visually assess the HR of daily operations, thereby facilitating the adoption of preemptive measures to protect the health of construction workers.

Iron (Fe), the main component of non-exhaust particulates, is known to have variable health effects that depend on the chemical species of iron. This study characterized the possible contribution of iron oxides and hydroxides to airborne brake-wear particles under realistic vehicle driving and braking conditions with different brake-pad friction materials. We found significant differences in wear coefficients and PM₁₀ emissions between non-asbestos organics (NAO) and European performance (ECE) brake pads. Iron was the dominant contributor to PM₁₀ and PM_2.5 brake-wear particles for both NAO and ECE. The iron concentration ratio in the particle mass were comparable to the disc to pads ratio measured by wear mass. The fact that magnetite, which is of interest with respect to health effects, was less abundant in NAO than in ECE suggested that tribo-oxidations occurred in NAO. Metallic iron is generated not only from abrasive wear but also from tribo-chemical reduction with magnetite as the starting material. We found differences not only in PM emissions between brake friction materials but also that the phase transformations of iron differed between friction materials. These differences were apparent in the distribution of iron oxides and hydroxides. Heat, tribo-oxidation, and tribo-reduction are intricately involved in these reactions.

Soil organic matter is an important component that reflects soil fertility and promotes plant growth. The soil of typical Chinese tea plantations was used as the research object in this work, and by combining soil hyperspectral data and image texture characteristics, a quantitative prediction model of soil organic matter based on machine vision and hyperspectral imaging technology was built. Three methods, standard normalized variate (SNV), multisource scattering correction (MSC) and smoothing, were first used to preprocess the spectra. After that, random frog (RF), variable combination population analysis (VCPA) and variable combination population analysis and iterative retained information variable algorithm (VCPA-IRIV) algorithms were used to extract the characteristic bands. Finally, the quantitative prediction model of nonlinear support vector regression (SVR) and linear partial least squares regression (PLSR) for soil organic matter was established by combining nine color features and five texture features of hyperspectral images. The outcomes demonstrate that, in comparison to single spectral data, fusion data may greatly increase the performance of the prediction model, with MSC+VCPA-IRIV+SVR (R2C=0.995, R2P=0.986, RPD=8.155) being the optimal approach combination. This work offers excellent justification for more investigation into nondestructive methods for determining the amount of organic matter in soil.

Leukodystrophies, also known as demyelinating diseases, mainly affect the CNS. Clinical presentation of different types of leukodystrophies can be nonspecific and thus, imaging techniques like MRI can be used for a more definitive diagnosis. These diseases are characterized as cerebral lesions with characteristic demyelinating patterns, which can be used as differentiating tools. In this review, we talk about these MRI imaging findings for each leukodystrophy, associated genetics, blood work that can help differentiate, emerging diagnostics, and follow up imaging strategy. The leukodystrophies discussed in this paper include X-linked adrenoleukodystrophy, Metachromatic leukodystrophy, Krabbe’s disease, Pelizaeus-Merzbacher disease, Alexander’s disease, Canavan disease, and Aicardi-Goutières Syndrome.

We review the topological gauge theory description of Josephson junction arrays (JJA), fabricated systems which exhibit the superconductor to insulator transition (SIT). This description revealed the topological nature of the phases appearing at the SIT and lead to the discovery of a new state of matter, the superinsulator, characterized by an infinite resistance, even at finite temperature, due to linear confinement of electric charges. This discovery is particularly relevant for the physics of superconducting films with emergent granularity, which are modeled by JJA, and share the same phase diagram.

The effect of organic matter (OM) on soil P-sorption is controversial and needs to be more investigated. The dissolved organic matter (DOM) may be regarded as an influential component on P sorption in natural soils. However, despite the great need for renewable sources of available P and OM in agricultural soils, little is known about interaction between P and DOM in natural soil systems. To uncover if and how soil saturation with DOM derived from different types of abundant agricultural wastes (cattle manure, horse manure, biogas digestate, compost) affects the phosphate sorption, we examined P sorption process in control and DOM-saturated sandy soils. The results indicated that organic matter introduced with agricultural wastes did not always reduce P sorption, but certainly had an effect on impairing P fixation and thus may result in potentially greater P mobility in the soil, including P availability. Up to now, we cannot recommend any of the tested organic amendments to directly overcome the P fixation in arable soils.

This paper describes the indoor air pollution in urban (Lahore, Faisalabad, Gujranwala, Rawalpindi and Karachi) Pakistani regions while considering the outdoor air and the health and wellbeing of the occupants present indoors. It also aims to assess previous methodological approaches Such as Air Conditioning Systems, used by developed countries to improve air quality to demonstrate the improvements that can be made in air quality in Pakistani urban areas. This research also investigates the causes, concentration and effects of poor air quality in Pakistani urban areas such as particulate matter (PM2.5), carbon oxides (COx), nitrogen oxides (NOx), sulphur oxides (SOx) and volatile organic compounds (VOC’s). The average concentration of these pollutants in Pakistan’s indoor air is, particulate matter (PM): [100 – 250 µg/m3 for PM2.5, 200 – 600 µg/m3 for PM10] 1 – 20 ppm for carbon monoxide (CO), nitrogen oxides (NOx): [50 – 100 µg/m3 for NO2, 20 – 40 µg/m3 for NO], 20 – 50 µg/m3 for sulfur dioxide (SO2), volatile organic compounds (VOCs): 0.1 – 0.5 ppm for formaldehyde, 5 – 10 µg/m3 for benzene and 20 – 30 µg/m3 for toluene. It should be noted that these concentrations can differ depending on the origin of pollution, location, and time of day. The literature review is made up of a combination of descriptive research methods that are used to inform the research background of ambient and indoor air quality, thus the literature review provides a theoretical and methodological background about the air pollution and its improvement in different parts of the world. According to the World Air Quality Index, Pakistan is the third most polluted country in terms of average PM2.5 concentration which is 14.2 times the WHO annual air quality guideline value. As a result, it is suggested that a PM2.5 concentration reduction program be implemented in urban Pakistani regions' indoor air.

In this investigation, we explore the existence and intriguing features of matter wave positons in a nonautonomous one-dimensional Bose-Einstein condensate (BEC) system with attractive interatomic interactions. We focus on the Gross-Pitaevskii (GP) equation/nonlinear Schrödinger (NLS)-type equation with time-modulated nonlinearity and trap potential, governing nonlinear wave propagation in the BEC. Our approach involves constructing second- and third-order matter wave positons using a similarity transformation technique. We also identify the constraints on the time-modulated system parameters that give rise to these nonlinear localized profiles. The study considers three distinct forms of modulated nonlinearities: (i) kink-like, (ii) localized or -like, and (iii) periodic. By varying the parameters associated with the nonlinearity strengths, we observe a rich variety of evolution behaviors in the matter wave positon profiles. These behaviors include stretching, curving, oscillating, breathing, collapsing, amplification, and suppression. Our comprehensive studies shed light on the intricate dynamics of matter wave positons in BECs, providing valuable insights into their behavior and characteristics in the presence of time-modulated nonlinearity and trap potential effects.

Air pollution is a leading cause of death in the United States, and is associated with adverse health outcomes, including increased vulnerability to coronavirus disease 2019 (COVID-19). The AirBeam2 was used to measure particulate matter with a diameter of 2.5 micrometers or smaller (PM2.5), to investigate differences between indoor and ambient levels at seven private homes in New York during and after the COVID-19 lockdown. Measurements taken in 2020 winter, spring and fall and in fall 2022 showed that 90% of the time, indoor PM2.5 levels exceeded outdoor levels both during and after the COVID-19 lockdown, p = 0.03, and exceeded safety levels. Higher indoor PM2.5 levels attributed to little or no ventilation from cooking and smoke in the kitchen and basements, were significantly greater in fall than in winter. Higher ambient PM2.5 levels were attributed to vehicular traffic at a street-facing sampling site. PM2.5 sources identified in this study may help in devising control strategies to improve indoor air quality (IAQ), and consequently alleviate respiratory health effects. These findings may be used as a basis for in-house modifications including natural ventilation and use of air purifiers to reduce exposures, mitigate future risks, and prevent potential harm to vulnerable residents.

Pharmaceutically active compounds (PhACs) enter soil with organic substrates such as manure. Such complex substrates differently affect PhACs’ soil sorption. To elucidate the effects, batch experiments were conducted using five selected chemicals as model constituents. Urea, KH2PO4, acetic acid, phenol and nonadecanoic acid (C:19) altered the sorption strength and/or nonlinearity of sulfadiazine, caffeine and atenolol in a topsoil. The nonlinear Freundlich model best described sorption. Overall, the PhACs’ sorption coefficients increased in the sequence urea&lt;phosphate&lt;phenol&lt;C:19&lt;acetic acid. The sorption nonlinearity also increased in most cases. The effects on sulfadiazine and caffeine were rather similar, but in many cases different from atenolol. Phosphate mobilized sulfadiazine and caffeine and urea mobilized sulfadiazine, which was explained by sorption competition resulting from specific preference of similar sorption sites. Soil sorbed phenol strongly increased the sorption of all three PhACs; phenolic functional groups are preferred sorption sites of PhACs in soil. The large increase in sorption of all PhACs by acetic acid was attributed to a loosening of the soil organic matter and thus the creation of additional sorption sites. The effect of C:19 fatty acid, however, was inconsistent. These results help to better understand the sorption of PhACs in mixtures of soil and manure.

The purpose of this study is to characterize atmospheric pollution and its sources in two West African urban sites during the dry season (January 2009 in Bamako, Mali, and December 2009 in Dakar, Senegal). Particulate Matter (PM) source apportionment was performed using Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF). Carbonaceous components, water-soluble inorganic compounds, and trace elements were analyzed from PM (TSP, PM10, and PM2.5) samples. The measured PM2.5 and PM10 concentrations were 5 to 10 times and 3 to 8 times higher than the 2005 WHO 24-hour standards, respectively. PCA and PMF analyses identify five sources in both cities. The sources contributing to aerosol concentrations (PM2.5 - PM10) in Bamako are motor vehicles (20-13%), solid fuel combustion (16-13%), crustal dust (24-30%), resuspended road dust (26-30%) and secondary aerosols (10-16%). During the sampling period in Bamako, dust was the most prevalent source, accounting for 63% of the total PM10 mass. In Dakar, the main identified sources were motor vehicles (28-19%), mineral dust (16-25%), industries and oil burn-ing (11-10%), sea salts (15-20%), and resuspended road particles (21-29%). The findings also indicate that anthropogenic emissions contribute significantly to the PM2.5 fraction, implying that populations are highly exposed to fine particles.

Generalisation from the local 4-dimensional spacetime form for a proper time interval provides an alternative basis for a unified theory contrasting with the more familiar approach of appending extra dimensions of space. In both cases the main goal is to derive a structure of matter that accounts for empirical observations from the properties of the additional components. Previous work has focussed upon the direct and significant connections that this new approach makes with the Standard Model of particle physics while also providing a link with dark matter models. In this paper we elaborate on how a further sector of generalised proper time, incorporating the key component of negative pressure, can account for the apparent dark energy fuelling the accelerating large-scale expansion of the universe. Through comparison with existing dark energy models we elucidate the elementary composition of this sector, its potential relation to an effective cosmological constant term, and the nature of possible interaction with the visible and dark matter sectors.

This hypothesis is the result of my conviction that science will oneday prove everything in space and time is part of a unification. In "A Brief History of Time", Stephen Hawking wrote, "If everything in the universe depends on everything else in a fundamental way, it might be impossible to get close to a full solution (of the universe's puzzles) by investigating parts of the problem (such as general relativity and quantum mechanics) in isolation." The goal: to establish a “proof of concept” to which equations can be added. It’s concluded the Steady State, Big Bang, Inflation and Multiverse theories all ultimately fail and a topological model including bits (binary digits), Mobius strips, figure-8 Klein bottles and Wick rotation works better. The failed cosmologies have impressive points leading to the idea that they’re all necessary stepping-stones. For example, the Big Bang is seen here as violation of the 1st Law of Thermodynamics but its supposed origin from quantum fluctuations is reminiscent of bits switching between 1 and 0. The topological hypothesis has potential to explain dark matter, dark energy, and electromagnetic-gravitational union. Finally, the article introduces what is called vector-tensor-scalar geometry - and extensions of Einstein's Gravity and Maxwell's Electromagnetism.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

We study the hadron-quark hybrid equation of state (EOS) of compact-star matter. The Nambu—Jona-Lasinio (NJL) local SU(3) model with vector-type interaction is used to describe the quark matter phase, while the relativistic mean field (RMF) theory with scalar-isovector $\delta$-meson effective field adopted to describe the hadronic matter phase. It is shown that the larger the vector coupling constant, the lower the threshold density for the appearance of strange quarks. For a sufficiently small value of the vector coupling constant, the functions of the mass dependence on the baryonic chemical potential have regions of ambiguity which leads to a phase transition in non-strange quark matter with an abrupt change in the baryon number density. We show that within the framework of the NJL model, the hypothesis on the absolute stability of strange quark matter is not realized. In order to describe the phase transition from hadronic matter to quark matter, the Maxwell's construction is applied. It is shown that the greater the vector coupling, the greater the stiffness of the EOS for quark matter and the phase transition pressure. Our results indicate that the infinitesimal core of the quark phase, formed in the center of the neutron star, is stable.

’Lockdown’ periods in response to COVID-19 have provided a unique opportunity to study the impacts of economic activity on environmental pollution (e.g. NO2, aerosols, noise, light). The effects on NO2 and aerosols have been very noticeable and readily demonstrated, but that on light pollution has proven challenging to determine. The main reason for this difficulty is that the primary source of nighttime satellite imagery of the earth is the SNPP-VIIRS/DNB instrument, which acquires data late at night after most human nocturnal activity has already occurred and much associated lighting has been turned off. Here, to analyze the effect of lockdown on urban light emissions, we use ground and satellite data for Granada, Spain, during the COVID-19 induced confinement of the city’s population from March 14 until May 31, 2020. We find a clear decrease in light pollution due both to a decrease in light emissions from the city and to a decrease in anthropogenic aerosol content in the atmosphere which resulted in less light being scattered. A clear correlation between the abundance of PM10 particles and sky brightness is observed, such that the more polluted the atmosphere the brighter the urban night sky. An empirical expression is determined that relates PM10 particle abundance and sky brightness at three different wavelength bands.

Coal-fired thermal plants (CTPP) are known to pollute the atmosphere with emission of many greenhouse gases and particulate matter. The power generation from these thermal plants cannot be stopped completely because it forms the backbone of the grid power supply. It is necessary to study the dispersion patterns of pollutants that affect the health of the people. The dispersion patterns are location specific since they depend on local meteorological conditions. In this study, the dispersion of particulate matter (PM) and sulphur dioxide (SO₂) from a CTPP with 275 m high stack are studied under different atmospheric boundary layer (ABL) of neutral, stable and unstable conditions up to a distance of 30 km from the stack. The plume of the PM spreads under all conditions. During some parts of the day, PM settles around the stack while at other times PM keeps suspending in the air for the full distance under study. Sulphur dioxide dilutes to concentrations below the detection limits in about 12-13 km from the stack for neutral and unstable ABL whereas for the stable ABL, the dispersion is up to 30 km. The 24 h weighted average concentration of sulphur dioxide, at 10 m height from the ground, is 14.2 mg/m³ at a distance of 25 kms from the CTPP, which is comparable with the value of 9.2 mg/m³ measured at the Air Quality Stations located around the same distance. Based on the results policy changes that need to be implemented are suggested.

While there is overwhelming evidence for dark matter (DM) in galaxies and galaxy clusters, all searches for DM particles have so far proved negative. It is not even clear whether only one particle is involved or a combination or particles, their masses not precisely predicted. This non-detectability raises the possible relevance of modified gravity theories – MOND, MONG, etc. Here we consider a specific modification of Newtonian gravity (MONG) which involves gravitational self-energy, leading to modified equations whose solutions imply flat rotation curves and limitations of sizes of clusters. The results are consistent with current observations including that involving large spirals. This modification could also explain the current Hubble tension. We also consider effects of dark energy (DE) in terms of a cosmological constant.

Background: There are major air pollution monitoring gaps in sub-Saharan Africa. Developing capacity in the region to conduct air monitoring in the region can help estimate exposure to air pollution for epidemiology research. The purpose of our study is to develop a land use regression (LUR) model using low-cost air quality sensors developed by a research group in Uganda (AirQo). Methods: Using these low-cost sensors, we collected continuous measurements of fine particulate matter (PM2.5) between May 1, 2019 and February 29, 2020 at 22 monitoring sites across urban municipalities of Uganda. We compared average monthly PM2.5 concentrations from the AirQo sensors with measurements from a BAM-1020 reference monitor operated at the US Embassy in Kampala. Monthly PM2.5 concentrations were used for LUR modeling. We used eight Machine Learning (ML) algorithms and ensemble modeling; using 10-fold cross validation and root mean squared error (RMSE) to evaluate model performance. Results: Monthly PM2.5 concentration was 60.2 µg/m³ (IQR: 45.4-73.0 µg/m³; median= 57.5 µg/m³). For the ML LUR models, RMSE values ranged between 5.43 µg/m³ - 15.43 µg/m³ and explained between 28% and 92% of monthly PM2.5 variability. Generalized additive models explained the largest amount of PM2.5 variability (R²=0.92) and produced the lowest RMSE (5.43 µg/m³) in the held-out test set. The most important predictors of monthly PM2.5 concentrations included monthly precipitation, major roadway density, population density, latitude, greenness, and percentage of households using solid fuels. Conclusion: To our knowledge, ours is the first study to model the spatial distribution of urban air pollution in sub-Saharan Africa using air monitors developed from the region itself. Non-parametric ML for LUR modeling performed with high accuracy for prediction of monthly PM2.5 levels. Our analysis suggests that locally produced low-cost air quality sensors can help build capacity to conduct air pollution epidemiology research in the region.

In this paper, we found new classes of exact models to the Einstein-Maxwell system of equations which describe the internal structure of a compact star made of strange matter considering the equation of state proposed by Rocha, Bernardo, de Avellar and Horvath in 2019. It has been assumed that this matter is composed of equal number of up, down and strange quarks and a small amount of electrons required to reaching the charge neutrality. If this hypothesis is correct, the neutron stars could be strange stars or hybrid stars with a thin crust of nuclei where the temperatures and pressures are capable of converting hadronic matter into this new stable phase of quarks. We have chosen a particular form of gravitational potential Z(x) that depends on an adjustable parameter related to degree of anisotropy of the models and the new solutions can be written in terms of elementary and polynomial functions. The obtained models satisfy all physical features expected in a realistic star and the expressions for mass, density and stellar radius are comparable with the experimental results.

Because of the widespread use of bisphenol analogues (BPs) as the alternatives to bisphenol A (BPA), they have attracted considerable attention for health risk in aquatic ecosystems. The occurrence and distribution of six BPs were researched in soluble phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. Except for bisphenol Z, all BPs were detected in the two or three phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the soluble phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the soluble and colloidal phases, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude higher than SPM, suggesting that colloids have an obvious impact on regulating BPs’ environmental behaviors. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Owing to the widespread use of bisphenol analogues (BPs) as bisphenol A (BPA) alternatives, they have been recognized to constitute a health risk for aquatic ecosystems. The occurrence and distribution of six BPs were investigated in the truly dissolved phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. With the exception of bisphenol Z, all BPs were detected in at least two phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the truly dissolved phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the truly dissolved phase and colloidal phase, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude greater than that of SPM, suggesting that colloids play an important role in regulating the environmental behaviors of BPs. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

In a recent Foundations of Physics paper [5] by the current author it was shown that, when the self-force problem of classical electrodynamics is properly solved, it becomes a plausible ontology underlying the statistical description of quantum mechanics. In the current paper we extend this result, showing that ordinary matter, thus represented, possibly suffices in explaining the outstanding observations currently requiring for this task the contrived notions of dark-matter, dark-energy and inflation. The single mandatory 'fix' to classical electrodynamics, demystifying both very small and very large scale physics, should be contrasted with other adhoc solutions to either problems. Instrumental to our cosmological model is scale covariance (and 'spontaneous breaking' thereof), a formal symmetry of classical electrodynamics treated on equal footing with its Poincare covariance, which is incompatible with the (absolute) metrical attributes of the GR metric tensor.

Particulate matter (PM) contains heavy metals that affect various cellular functions and gene expression associated with an array of acute and chronic diseases, in humans. However, their specific effects on the stem cells remain unclear. Here, we report the effects of PM collected from Jeddah city on bone marrow mesenchymal stem cells (BM-MSCs) on proliferation, cell death, related gene expression and systems biological analysis aiming to understand the underlying mechanisms. Two different sizes (PM_2.5-₁₀) were tested in vitro at various concentrations (15 to 300 µg/ml) and durations (24 to 72 h). PMs induced cellular stress including membrane damage, shrinkage and death. Lower concentrations of PM_2.5 increased BM-MSCs proliferation, while higher concentrations decreased it. PM₁₀ decreased BM-MSCs proliferation in a concentration-dependant manner. The X-Ray Fluorescence spectrometric analysis showed that PM contains high levels of heavy metals. Ingenuity Pathway Analysis (IPA) and hierarchical clustering analyses showed that heavy metals were associated with signalling pathways involving cell stress/death, cancer and chronic diseases. qRT-PCR results showed differential regulation of the apoptosis genes (BCL2, BAX); upregulation of inflammation associated genes (TNF-a and IL-6) and downregulation of cell cycle regulation gene (P53). We conclude that PM could affect different cellular functions and predispose to debilitating diseases.

Spectral characteristics of CDOM in water column are a key parameter for bio-optical modeling. Knowledge of CDOM optical properties and spatial discrepancy based on the relationship between water quality and spectral parameters in Yinma River watershed with in situ data collected highly-polluted waters are exhibited in this study. Seasonal field data sets collected over a period of 2 months in 2015 in Yinma River Watershed. Based on the comprehensive index method, the riverine waters showed serious contamination, especially the COD, Fe, Mn, Hg and DO were out of range contamination warning. Dissolved organic carbon (DOC) and total suspended matter (TSM) with prominent non-homogenizing were significantly high in the riverine waters, but chlorophyll-a (Chl-a) was opposite. Ternary phase diagram showed that non-algal paritcles absorption played an important role in total non-water light absorption (>50%) in most sampling locations, and mean contribution of CDOM were 13% and 22% in summer and autumn respectively. Analysis of ratio of absorption at 250-365 nm (E_250:365) and spectral slope (S_275-295) indicated that CDOM had higher aromaticity and molecular weight in autumn than in summer, is consistent with the results of water quality and relative contribution. Redundancy analysis (RDA) indicated that the environmental variables OSM had a strong correlation with CDOM absorption, followed by heavy metal, e.g., Mn, Hg and Cr⁶⁺. However, for the specific UV absorbance (SUVA₂₅₄), the seasonal values showed opposite results compared with the reported literature. The potential reasons were the more UDOM (uncolored Dissolved Organic Matter) from human source (wastewater effluent) existed in waters. Terrigenous inputs simultaneously are in relation to the a_CDOM(440)-DOC relationship with the correlation coefficient was 0.90 in summer (2-tailed, p<0.01), and 0.58 in autumn (2-tailed, p<0.05). Spatial distribution of CDOM parameters exhibited that the downstream regions focused on dry land have high CDOM molecular weight and aromatic hydrocarbon. Partial sampling locations around the cities or countries generally showed abnormal values due to terrigenous inputs. As a bio-optical model parameter, spectral characteristic of CDOM is helpful in adjusting the derived algorithms in highly-polluted environments. The study on organic carbon and pollutants in highly-polluted waters had an important contribution to global carbon balance estimation and water environment protection.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

This paper presents a numerical study on the laser shock wave propagation in a 3D woven CFRP material by means of detailed and homogenized FE models. The aim of the study is to numerically characterize the shock wave response of the 3D woven CFRP in terms of back face velocity profiles and the induced damage and to investigate whether the detailed FE models could be replaced by homogenized FE models. The 3D woven geometry was designed using the TexGen software, while the numerical analyses were executed using the LS-Dyna explicit FE software. A high-strain rate behavior was considered for the matrix. The fiber bundles in the detailed models were modeled as a high fiber content unidirectional composite laminate, with its mechanical properties calculated by micromechanical equations. Both for the fiber bundles of the detailed model and the homogenized models a progressive damage material model was applied. The results of the detailed model reveal a considerable effect of material’s architecture on the shock wave propagation and the sensitivity of the back face velocity profile to the spot location. Consequently, the homogenized model is not capable of accurately simulating the shock wave response of the 3D woven composite. Moreover, the detailed predicts with high accuracy matrix cracking in the resin-rich areas and in the bundles as well as fiber failure. On the contrary, the homogenized model predicts matrix cracking at the same areas and no fiber failure.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Background The prognostic value of estimated pulse wave velocity (ePWV) has been infrequently explored in high-risk patient groups. Our study aimed to evaluate the prognostic significance of ePWV among patients undergoing percutaneous coronary intervention (PCI) with drug-eluting stent (DES). Methods A total of 4,119 consecutive subjects who underwent PCI with DES (mean age, 67.1 ± 11.6 years and 33.1% were female) were retrospectively analyzed. ePWV was calculated based on the patient’s age and mean blood pressure. Major adverse cardiovascular event (MACE), including cardiac death, non-fatal myocardial infarction, coronary revascularization, and ischemic stroke, were evaluated. Reults During a median follow-up duration of 3.51 years (interquartile range, 1.35 ~ 6.37 years), there were 746 MACE (18.1%). Multivariable analysis showed that higher ePWV was associated with higher MACE incidence (middle tertile vs. the lowest tertile: hazard ratio [HR], 2.49; 95% confidence interval [CI], 1.81-3.42; P < 0.001; the highest tertile vs. the lowest tertile: HR, 6.18; 95% CI, 4.33-8.80; P < 0.001) The inclusion of ePWV data significantly increased the global chi-square values when added to the clinical information (from 96 to 128; P < 0.001). Conclusion ePWV demonstrated a significant association with MACE in patients who underwent DES implantation. Given its relative simplicity to calculate, ePWV could potentially serve as a valuable instrument for stratifying cardiovascular risk within this high-risk patient population.

Objective: The main purpose of the study is to investigate the combined effects of polydeoxyribonucleotide (PDRN) and extracorporeal shock wave therapy (ESWT) sequences on the regenerative processes in atrophied animal muscles. Methods: Thirty male New Zealand rabbits, aged 12 weeks, were divided into five groups: normal saline, PDRN, ESWT, PDRN injection before ESWT, and PDRN injection after ESWT. Following 2 weeks of cast immobilization, the respective treatments were administered to the atrophied calf muscles. Radial ESWT was performed twice weekly. The evaluation included measurements of calf circumference, tibial nerve compound muscle action potential (CMAP), and gastrocnemius (GCM) muscle thickness after 2 weeks of treatment. Histological and immunohistochemical staining, as well as Western blot analysis, were conducted 2 weeks post-treatment. Staining intensity and extent were assessed using semi-quantitative scores. Results: Groups 4 and 5 demonstrated significantly greater calf muscle circumference, GCM muscle thickness, tibial nerve CMAP, and GCM muscle fiber cross-sectional area (types I, II, and total) than in the remaining three groups (p < 0.05), while they did not did not differ significantly in these parameters. Groups 2 and 3 showed the higher values for all the observations compared to group 1 (p < 0.05). Group 4 had the greatest ratio of vascular endothelial growth factor (VEGF) to platelet endothelial cell adhesion molecule-1 (PECAM-1) in the gastrocnemius muscle fibers than in the other four groups (p < 0.05). Western blot analysis revealed significantly higher expression of angiogenesis cytokines in groups 4 and 5 than in the remaining (p < 0.05). Conclusion: The combination of ESWT and PDRN injection demonstrated superior regenerative efficacy for atrophied calf muscle tissue in rabbit models than these techniques alone or saline. Particularly, administering ESWT after PDRN injection yielded the most favorable outcomes in specific parameters.

Electrocardigraphy remains as a first-line evaluation method for cardiac function, recording the electrical activity of the heart from the body surface. Since atrial activation is seen on the ECG as P-wave, several factors are known to impact the appearance of the P-wave, such as direction of electric impulse, conduction abnormalities and anatomical characteristics of the atria. The aim of this retrospective study was to find statistically significant associations between anatomy of pulmonary veins (PVs) osberved in cardiac computed tomography (CT) and P-wave appearance during sinus rhythm on resting ECG. For each patient, a resting 12-lead ECG was recorded, the field of analysis was P wave – its’ duration, morphology and axis. The evaluation of the CT scan recordings was performed by creating 3D models of the left atrium and analyzing anatomy of the PVs and left atrial appendage (LAA). Noteworthy correlations were found: anatomy of the left PVs showed an association with LAA volume, LAA morphology and P-wave notching in lead II. The right PVs demonstrated relation with P wave axis and amplitude. Although these correlations cannot be classified as strong, they may play a role in significant scientific discoveries in future research projects.

This paper presents a 32 GHz high power amplifier (HPA) with a design strategy to achieve a high-power output with reliable operation for the Ka-band deep space satellite communication in 150 nm GaN HEMT technology. The presented Ka-band HPA employs a cascaded two-stage common source amplifier topology, and the output stage is comprised of an 8-way power combining network in current mode. The interstage matching network is designed with the bandpass configuration utilizing capacitors and transmission lines to provide better stability at the low-frequency regime. The implemented Ka-band HPA achieved a peak power gain of 7.3 dB at 32 GHz and a 3 dB bandwidth was 3.5 GHz between 31.3 and 34.8 GHz. The saturated output power at the peak power added efficiency (PAE) of 19.3% was 38.2 dBm, and the output 1 dB gain compression point (OP1dB) was 27.4 dBm in the measurement. The designed HPA consumes an area of 19.35 mm^2 including RF signal, and DC pads

In this paper, the feasibility of automated and accurate in vivo measurements of vascular parameters continuously and non-invasively using ultrasound sensor is presented. Vascular parameters such as pulse wave velocity (PWV), blood pressure (BP), arterial compliance (AC) and stiffness index (SI) are affluent indicators of cardiovascular disorders and needs to be monitored non-invasively and continuously during surgeries and follow-up procedures. Cuff based or invasive catheter techniques are considered as gold standard to measure BP and are fed manually to compute AC and SI which employ imaging algorithms. In this context, a Continuous and Non-Invasive Vascular Stiffness and Arterial Compliance Screener (CaNVAS) is developed to measure said parameters continuously and non-invasively using ultrasound sensor. Acoustic waves of 5 MHz (2.2 – 10 MHz) are driven through target arterial walls, reflected echoes captured, pre-processed and frequency shift is used to calculate PWV. It is observed that PWV measured using CaNVAS varies exponentially with BP values obtained from sphygmomanometer (BPMR-120) and this relationship is used to compute instantaneous values of BP. The proposed device is validated by performing measurements on 250 subjects in pre and post exercise conditions and found to have 95% accuracy and an average of 12.5% coefficient of variation.

In order to study the surface settlement law of subway tunnel engineering site overlying soft soil layer under the action of earthquake, ABAQUS finite element analysis software was used to study the surface settlement law of subway tunnel construction site overlying soft soil layer under the action of three different seismic waves, including El-Centro wave, Kobe wave, and artificial seismic wave with exceedance probability of 10%, based on the Dalian Metro Line 5 with overlying soft soil layer as the engineering background, and the law was analyzed theoretically. Then, the surface settlement law of tunnel top was studied based on El-Centro wave and soft soil parameters, and the sensitivity analysis of soft soil parameters on surface settlement of tunnel top was carried out by orthogonal test method. The results show that under earthquake action, the settlement of the strata within a certain range of the tunnel roof is significantly greater than that of the surrounding strata, forming a settlement trough with a width of about 8 to 20 meters. The width of the settlement trough under the El-Centro wave is the largest, about 19.6 meters, surpassing the artificially synthesized seismic waves with a probability of 10%, which is about 15.6 meters, while the width of the settlement trough under the Kobe wave is the smallest, about 8.5 meters. The ground surface within a range of about 20 meters above the tunnel roof is most strongly affected by the seismic waves and the special lithology of the overlying soft soil layer, and the settlement is the largest. The settlement law of the settlement trough in the overlying strata of the tunnel conforms to the Peck formula. Increasing the elastic modulus of the silty soil can reduce the settlement of the ground surface above the tunnel roof, increasing the Poisson's ratio of the silty soil will increase the settlement of the ground surface above the tunnel roof, increasing the cohesive force of the silty soil to 20 kPa will basically stabilize the settlement of the ground surface above the tunnel roof, and increasing the internal friction angle of the silty soil will basically not change the settlement of the ground surface above the tunnel roof. The sensitivity of the soft soil parameters to the settlement of the ground surface above the tunnel roof is in the order of Poisson's ratio, elastic modulus, cohesive force, and internal friction angle.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

For W-band long-range mm-wave wireless transmission systems, nonlinearity issues resulting from photoelectric devices, optical fiber, and wireless power amplifiers can be handled by deep learning equalization algorithms. Besides, the PS technique is considered an effective measure to further increase the capacity of the modulation-constraint channel. However, since the proba-bilistic distribution of m-QAM varies with the amplitude, there have been difficulties in learning valuable information from the minority class. This limits the gain of nonlinear equalization. To overcome the imbalanced machine learning problem, we propose a novel two-lane DNN (TLD) equalizer with the random over-sampling (ROS) technique in this paper. The combination of PS at the transmitter and ROS at the receiver improves the overall performance of the W-band wireless transmission system, and our 4.6-km ROF delivery experiment verifies its effectiveness for the W-band mm-wave PS-16QAM system. Based on our proposed equalization scheme, we realize single-channel 10-Gbaud W-band PS-16QAM wireless transmission over 100 m optical fiber link and 4.6-km wireless air-free distance. The results show that compared with the typical TLD without ROS, the TLD-ROS can improve the receiver sensitivity by 1dB. Furthermore, a reduction of 45.6% in complexity is realized, and training samples can be reduced by 15.5%. Considering the actual wireless physical layer with its requirements, there is much to be gained from the joint use of deep learning and balanced data pre-processing techniques.

The evolution in the post shock nonequilibrium relaxation in a hypersonic plasma flow was investigated during a shock’s reflection off a thermal discontinuity. Within a transitional period, the relaxation zone parameters past both, the reflected and transmitted waves, evolve differently compared to that in the incident wave. In a numerical example for the non-dissociating N₂ gas heated to 5000 K/10,000 K across the interface and M = 3.5, the relaxation time for the transmitted wave is up to 50% shorter and the relaxation depth for both waves is significantly reduced, thus resulting in a weakened wave structure. The results of extension into larger values of heating strength and the shock Mach numbers are discussed. The findings can be useful in the areas of research involving strong shocks interacting with optical discharges or other heated media on the scale where the shock structure becomes important.

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

We report photon-phonon atomic coherence (cascade- and nested-dressing) interaction from various phase transitions of Eu3+: BiPO4 crystal. Such atomic coherence spectral interaction evolves from out of phase fluorescence to in-phase spontaneous four-wave mixing (SFWM) by changing the time gate. The dressing dip switch and three dressing dips of SFWM result from strong photon-phonon destructive cross- and self-interaction for hexagonal phase, respectively. The more phonon dressing result in destructive interaction, while less phonon dressing result in constructive interaction of atomic coherences. The experimental measurements of photon-phonon interaction agree with theoretical simulations. Based on our results, we proposed a model for an optical transistor (as an amplifier and switch).

Predicting the tidal wave is essential not only to better understand hydrological cycle at the boundary between land and ocean but also to improve energy production in the coastal area. As affected by various factors such as astronomical, meteorological, and hydrological effects, predicting the tidal wave at the estuary remains uncertain. In this study, we present a novel method to improve short-term tidal wave predictions using a fixed-lag smoother based on sequential data assimilation (DA). The proposed method is implemented for the tidal wave predictions at the estuary of Nakdong River. As a result, the prediction accuracy was improved by 63.9% with DA and the calibration using the regression. Although the accuracy of DA diminished for increasing forecast lead times, the 1-hr lead forecast by DA had still 44.4% improvement over the open loop without DA. Plus, the optimal conditions for the fixed-lag smoother were analyzed in terms of the order of a smoothing function and the length of assimilation window and forecast lead time. It was suggested that the optimal DA configuration could be obtained with the 8th order polynomial as a smoothing function assimilated under 6-hr or longer past and future DA windows.

Monsoon winds drive upwelling along the eastern coast of India during the south-west (SW) monsoons. These winds also provide alongshore windstress (AWS) resulting in positive cross-shore Ekman transport (ET) from March to the end of September. While instances of high ET and sea surface temperature based upwelling index (UI_SST) were observed along two parts of the coast: between Kashinagara and Kakinada in the north, and between Kavali and Point Calimere in the south. The UI_SST illustrated a much poorer agreement with local ET in the northern section, where the onset of UI_SST preceded the rise of ET and the subsidence of UI_SST signals occurred during a period of rising ET. Additionally, negative sea surface height anomalies (SSHAs), typically associated with coastal upwelling, were also missing through most of the upwelling period. A complex empirical orthogonal function (CEOF) analysis revealed two coherent modes of SSHA variation. The first mode showed a SSHA signature spatio-temporally coincident with the first upwelling and downwelling Kelvin waves closely associated with the equatorial zonal winds that drive them. The second CEOF mode, with a coastal SSHA pattern similar to the SSHA signatures of coastal upwelling, was associated with local offshore ET along the Indian east coast. The CEOF analysis exhibited the triggering of coastal upwelling in April and its suppression from June by coastally trapped Kelvin waves along the northeastern coast of India, while local AWS driven ET was the primary driver of coastal upwelling along the southeastern coast. The second CEOF mode also exhibited a coherent negative coastal SSHA signature excited by local AWS driven ET during the upwelling period. This study examined the spatio-temporal variability of premonsoon and SW monsoon coastal upwelling along the western Bay of Bengal and its relation to remotely forced coastal Kelvin waves.

Monsoon winds drive upwelling along the eastern coast of India during the south-west (SW) monsoons. These winds also provide alongshore windstress (AWS) resulting in positive cross-shore Ekman transport (ET) from late May to the end of September. While instances of high ET and sea surface temperature (SST) based upwelling index (UI_SST) were observed along different parts of the coast, UI_SST was weaker in the northern section in the earlier part of monsoon. This was even in the presence of maximum AWS and ET during the 10 years analysis period spanning January-2009 to December-2018. Additionally, negative sea surface height anomalies (SSHAs), typically associated with coastal upwelling, were observed only along the southern-most coast. An empirical orthogonal function (EOF) analysis revealed two coherent modes of SSHA variation. The first principal component (PC) showed a SSHA signature coincident spatio-temporally with the first downwelling Kelvin wave, closely associated with the equatorial zonal winds that drive coastal Kelvin waves. The third PC with a coastal SSHA pattern similar to the second upwelling Kelvin wave was associated with offshore ET along the northern part of the Indian east coast. Time series of the two PCs exhibited suppression of coastal upwelling by downwelling Kelvin waves during May-July along the northeastern coast of India. Local AWS driven ET was the primary driver of coastal upwelling with the weakening of the remotely forced Kelvin waves in August. A coherent mode consisting of negative coastal SSHA signature was excited in response to local AWS driven ET during the upwelling period. This study examined the spatio-temporal variability of SW monsoon coastal upwelling along the east coast of India and illustrated the role of equatorial windstress forced first downwelling Kelvin wave in suppressing upwelling in the northern part of the coast during early SW monsoon season.

Lipoproteins are important cardiovascular (CV) risk biomarkers. This study aimed to investigate the associations of lipoprotein subclasses with micro- and macrovascular biomarkers to better understand how these subclasses relate to atherosclerotic CV diseases. One hundred fifty-eight serum samples from the EXAMIN AGE study, consisting of healthy individuals and CV risk patients, were analyzed by nuclear magnetic resonance (NMR) spectroscopy to quantify lipoprotein subclasses. Microvascular health was quantified by measuring retinal arteriolar and venular diameters. Macrovascular health was quantified by measuring carotid-to-femoral pulse wave velocity (PWV). Nineteen lipoprotein subclasses showed statistically significant associations with retinal vessel diameters and nine with PWV. These lipoprotein subclasses together explained up to 26% of variation (R²=0.26, F(29,121)=2.80, p<0.001) in micro- and 12% (R²=0.12, F(29,124)=1.70, p=0.025) of variation in macrovascular health. High-density (HDL-C) and low-density lipoprotein cholesterol (LDL-C) as well as triglycerides together explained up to 13% (R²=0.13, F(3,143)=8.42, p<0.001) of micro and 8% (R²=0.08, F(3,145)=5.46, p=0.001) of macrovascular variation. Lipoprotein subclasses seem to reflect micro- and macrovascular end organ damage more precisely as compared to only measuring HDL-C, LDL-C and triglycerides. Further studies are needed to analyse how the additional quantification of lipoprotein subclasses can improve CV risk stratification and CV disease prediction.

Planetary waves in the mesosphere are studied using observational data and models to establish their origin, as there are indications of their generation independently of waves in the stratosphere. The quantitative relationships between zonal wave numbers m = 1 (wave 1) and m = 2 (wave 2) were studied with a focus on the mid-latitude mesosphere at 50N latitude. Aura Microwave Limb Sounder measurements were used to estimate wave amplitudes in geopotential height during the 2020–2021 winter major sudden stratospheric warming. The moving correlation between the wave amplitudes shows that, in comparison with the anticorrelation in the stratosphere, wave 2 positively correlates with wave 1 and propagates ahead of it in the mesosphere. A positive correlation r = 0.5–0.6, statistically significant at the 95% confidence level, is observed at 1–5-day time lag and in the 75–91 km altitude range, which is the upper mesosphere–mesopause region. Wavelet analysis shows a clear 8-day period in waves 1 and 2 in the mesosphere at 0.01 hPa (80 km), while in the stratosphere–lower mesosphere the period is twice as long at 16-days; this is statistically significant only in wave 2. Possible sources of mesospheric planetary waves are discussed.

In this article, the general solution of the tachyonic Klein-Gordon equation is obtained as a Fourier integral performed on a suitable path in the complex \omega-plane. In particular, it is proved that under given boundary conditions this solution does not contain any superluminal components. On the basis of this result, we infer that all possible spacelike wave equations describe the dynamics of subluminal particles endowed with imaginary mass. This result is validated for the Chodos equation, used to describe the hypothetical superluminal behaviour of neutrino. In this specific framework, it is proved that the wave packet propagates in spacetime with subluminal group velocities and that for enough small energies it behaves as a localized wave.

The current need to develop sustainable power sources has led to the development of ocean-based conversion systems. Wells turbine is a widely used converter in such systems which suffers from a lack of operational range and power production capacity under operational conditions. The profile named IFS which is concave in the post-mid-chord region, can produce significantly larger lift forces and show better separation behavior than the NACA profiles. In the present study, we tested this profile for the first time in a Wells turbine. The performance of six different blade designs with IFS and NACA profiles were evaluated and compared using a validated computational fluid dynamic model. Although the substitution of the NACA profile with the IFS profile in all cases increased the torque generated, the most efficient power generation and the largest efficient range were achieved in the design with varying thickness from the hub with a 0.15 thickness ratio reaching to the ratio of 0.2 at the tip. The operational span of this design with the IFS profile was 24.1% greater and the maximum torque generation was 71% higher than the case with the NACA profile. Therefore, the use of the IFS profile is suggested for further study and practical trials.

Hasselmann and coauthors proposed the discrete interaction approximation (DIA) as the best tool replacing the nonlinear evolution term in a numerical wind-wave model. Much later, Polnikov and Farina radically improved the original DIA by means of location all the interacting four wave vectors, used in the DIA configuration, exactly at the nodes of the numerical frequency-angular grid. This provides nearly two-times enhancing the speed of numerical calculation for the nonlinear evolution term in a wind-wave model. For this reason, the proposed version of the DIA was called as the fast DIA (FDIA). In this paper we demonstrate all details of the FDIA concept for several frequency-angular numerical grids of high resolution, with the aim of active implementation the FDIA in modern versions of world-wide used wind-wave models.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Hamiltonians describing the relativistic quantum dynamics of a particle with an arbitrary spin are shown to exhibit a supersymmetric structure when the even and odd elements of the Hamiltonian commute. For such supersymmetric Hamiltonians an exact Foldy-Wouthuysen transformation exits which brings it into a block-diagonal form separating the positive and negative energy subspaces. Here the supercharges transform between energy eigenstates of positive and negative energy. The relativistic dynamics of a charged particle in a magnetic field is considered for the case of a scalar (spin-zero) boson obeying the Klein-Gordan equation, a Dirac (spin one-half) fermion and a vector (spin-one) boson characterised by the Proca equation.

The production of instant green tea requires hot-water extraction, which is time consuming and contributes to losses in aromatic compounds. In this study, an ultrasonic-assisted technology was used to improve the extraction efficiency of green tea, thereby shortening extraction time from 45 to 15 min. In pure water, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 0.23 mg/mL and total tea polyphenol dissolution decreased by 3.2 mg/mL. In 76.2% ethanol, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 1.57mg/mL and total tea polyphenol dissolution decreased by 1.5 mg/mL. Additionally, we used microwave-assisted technology to further improve the extraction efficiency of green tea, which shortened the extraction time to 2 min. However, the extraction rate remained unchanged. In pure water, the dissolution of caffeine and theanine did not change significantly, but the dissolution of total catechins increased by 0.41 mg/mL and the dissolution of tea polyphenols decreased by 2.9 mg/mL. Ultrasonic treatment increased the proportion of 3-hydroxybutan-2-one, (5S)-5-(hydroxymethyl)oxolan-2-one and 2-phenylethanol, which were the main aroma compounds in tea. Microwave treatment changed the aroma compounds in tea, causing losses in aroma compounds with low boiling point and maintaining (5S)-5-(hydroxymethyl)oxolan-2-one. The taste and aroma of instant green tea improved based on sensory evaluation results.

In the present work, a superlattice structure comprising superconducting and insulator layers is studied. Here, if a magnetic field is applied parallel to the layers, the lack of a pinning center leads to a novel transition; in particular, as the applied magnetic field is reduced, the stationary wave surrounding the magnetic flux quantum in the superconducting layer eventually collides with the superconducting–insulating interfaces on both sides because its radius becomes larger than the width of the superconducting layer. At this instant, the stationary wave will collapse, and a transition will occur: the magnetic quanta are collapsed and thus the uniform magnetic field distribution is achieved, which corresponds to the transition from the superconducting state to the normal state over critical current. Considering a one-dimensional model of the structure, a critical current density equation is derived that indicates an increase in the critical current density for increased applied magnetic field. Subsequently, the same calculation was conducted after changing the direction of the magnetic field component, and the combination of these two calculations expresses the anisotropic property of the structure. The phenomenon is also predicted for anisotropic critical current density. This phenomenon is an important discovery that helps manufacture high-temperature superconducting tape as well as large high-temperature superconducting coils.

In this study, a matched-mode autoregressive source depth estimation method (MMAR) based on autoregressive (AR) wavenumber estimation is proposed for a moving source in shallow water waveguides. The signal original frequency and the environmental parameters, namely, the sound speed profile and bottom properties are known as a prior knowledge. The mode wavenumbers are estimated by the AR modal wavenumber spectrum. On the basis of the mode wavenumber estimation, the mode amplitudes can be estimated by the wavenumber spectrum that is obtained by generalized Hankel transform. The source depth estimation is determined by the peak of source depth function wherein the data mode best matches the replica mode that is calculated using a propagation model. Compared with other methods of moving source depth estimation, the proposed method exhibits a better performance in source depth estimation under low signal-to-noise ratio or the small range span. The selection of horizontal line array depth is illustrated by simulation and normal mode theory in details.

In the summertime, convections occur frequently over the Tibetan Plateau (TP) because of the large dynamic and thermal effects of the landmass. Measurements of vertical air velocity in convective cloud are useful for advancing our understanding of the dynamic and microphysical mechanisms of clouds and can be used to improve the parameterization of current numerical models. This paper presents a technique for retrieving high-resolution vertical air velocity from convective cloud over the TP, by using Doppler spectra from a vertically pointing Ka-band cloud radar. The method is based on the development of a “small-particle-traced” idea and the necessary data processing and uses three modes of radar. Spectral broadening corrections, uncertainty estimations, and result merging are used to ensure accurate results. Qualitative analysis of two typical convective cases shows that the retrievals are reliable and agree with the expectant results inferred from other radar measurements. A quantitative retrieval of vertical air motion from a ground-based optical disdrometer is used to preliminarily validate our radar-derived results. The comparison illustrates that while the data trends from the two methods of retrieval are similar, with the updrafts and downdrafts coinciding, cloud radar has a much higher resolution and can reveal the small-scale variation of vertical air motion.

The aim of this work is to present a design approach of a Shock-Induced Combustion Ramjet (Shcramjet) inlet, and present its optimization in terms of the flow and geometrical parameters. The flow properties of mixed compression type inlet of a Shcramjet are examined using analytical and numerical techniques. The geometries obtained with variations in the wedge angles, length, height and cowl lip positions are used to study the flow characteristics of inlet, identifying bow shock temperature ratio as the optimization parameter. The two-dimensional geometries of two-shock and three-shock inlet models designed analytically for shock-on-lip condition at Mach 12.5 and an altitude of 32.5 km are numerically simulated in OpenFOAM CFD Toolbox. A density based compressible CFD solver based on central upwind schemes of Kurganov and Tadmore is used to solve 2D inviscid Euler equations. The inlet total pressure recovery is expressed as a function of temperature ratios of compression shocks, and is found to have a maxima at a bow shock temperature ratio at the design condition when the bow and external shocks have equal strengths. The effect of considering the flow to be calorically imperfect is studied numerically, and the deviation from the analytical design is presented.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

We study the effect of the generation of the mechanical transverse wave (MTW)　travelling in the opposite direction (OD) to a moving medium (MM) on the relativistic energy conservation law (RECL). From the viewpoint of the relativity of simultaneity (RS), the time on the coordinate coinciding with the advance end of the wave (AEW) travelling toward the rear of the MM passes faster than that on the coordinate coinciding with the wave source (WS). Then the AEW in the MM travels forward compared to that in the rest frame of reference (RFR) which is stationary relative to the medium when the time on the coordinate coinciding with the WS is same for each inertial frame of reference (IFR). Hence, the coordinate interval (CI) between the AEW and WS in the MM is observed to be larger than that between them in the RFR. We show that this difference holds true for the CI of any portion having transverse velocities mutually converted by the Lorentz transformation (LT). This difference in the CI leads to that in the rest mass (RM). We demonstrate that the RM included in wave motion (WM) in the MM is larger than one included in WM in the RFR when comparing the portions having transverse velocities mutually converted by the LT. This relation holds true for all portions in WM. Therefore, the total coordinate interval of the portion (CIP) and total RM (TRM) included in WM in the MM (WMMM) are large compared to them included in WM in the RFR. Furthermore, we compare the relativistic kinetic energy (RKE) of the MTW travelling in the OD to the MM (ODMM) with that of the MTW propagating in the direction vertical to the moving direction of the medium. We prove that the CIP and RM included in the former MTW are larger than them included in the latter MTW when comparing each portion with the same transverse velocity (TV). Moreover, the total CIP and TRM included in the former MTW are also large compared to them included in the latter MTW. The reason for these is that the latter CIP and RM are equal to them in the RFR when comparing the portions having transverse velocities mutually converted by the LT. On the other hand, the energy supplied to generate each MTW is the same. From these, we demonstrate that the RKE of the MTW travelling in the ODMM can be larger than the total relativistic energy (TRE) of the MTW propagating in the direction vertical to the moving direction of the medium. Consequently, we propose a violation of the RECL and Einstein’s principle of relativity (EPR) because the TRE is not necessarily conserved in the IFR in which the medium is moving.

This paper derives measurement and identical principles, then makes the two principles into measurement and identical theorems of quantum mechanics, plus the three theorems derived earlier, we deduce the axiom system of current quantum mechanics, the general quantum theory no axiom presumptions not only solves the crisis to understand in current quantum mechanics, but also obtains new discoveries, e.g., discovers the velocities of quantum collapse and entanglement are instantaneously infinitely large. We deduce the general Schrȍdinger equation of any n particles from two aspects, and the wave function not only has particle properties of the complex square root state vector of the classical probability density of any n particles, but also has the plane wave properties of any n particles. Thus, the current crisis of the dispute about the origin of wave- particle duality of any n microscopic particles is solved. We display the classical locality and quantum non-locality for any n particle system, show entanglement origins, and discover not only any n-particle wave function system has the original, superposition and across entanglements, but also the entanglements are of interactions preserving conservation or correlation, three kinds of entanglements directly give lots of entanglement sources. This paper discovers, one of two pillars of modern physics, quantum mechanics of any n particle system is a generalization ( mechanics ) theory of the complex square root ( of real density function ) of classical statistical mechanics, any n particle system’s quantum mechanics of being just a generalization theory of the complex square root of classical statistical mechanics is both a revolutionary discovery and key new physics, which are influencing people’s philosophical thinking for modern physics, solve all the crisises in current quantum theories, quantum information and so on, and make quantum theory have scientific solid foundations checked, no basic axiom presumption and no all quantum strange incomprehensible properties, because classical statistical mechanics and its complex square root have scientific solid foundations checked. Thus, all current studies on various entanglements and their uses to quantum computer, quantum information and so on must be further updated and classified by the new entanglements. This and our early papers derive quantum physics, solve all crisises of basses of quantum mechanics, e.g., wave-particle duality & the first quantization origins, quantum nonlocality, entanglement origins & classifications, wave collapse and so on.Key words: quantum mechanics, operator, basic presumptions, wave-particle duality, principle of measurement, identical principle, superposition principle of states, entanglement origin, quantum communication, wave collapse, classical statistical mechanics, classical mechanics

BACKGROUND AND OBJECTIVE: The use of biomass for cooking carries significant health implications and can lead to adverse environmental issues such as deforestation, greenhouse gas emissions, and erosion. Despite these concerns, there is a lack of information about the nature and extent of cooking emissions in many developing countries. To address this gap, a study was conducted to assess cooking emission levels and their associated health effects among households in Dodoma City, Tanzania. METHODS: A descriptive cross-sectional design was conducted, involving 285 households in the peri-urban area of Dodoma City, Tanzania. A combination of questionnaires, observational checklists, and sampling devices (Aeroqual series 500 for Carbon Monoxide and Temptop PMD 351 for Particulate Matters) were employed for data collection, adhering to established protocols. Additionally, lung function tests were conducted with consent from the primary household cooks. Collected data were entered into an Excel spreadsheet and analyzed using STATA 17 software. FINDINGS: Out of 285 participants, 74.7% predominantly use charcoal for cooking, with 68.4% having outdoor kitchen setups. Significant differences in pollutant concentrations were observed across various fuel types (P=0.0001), with firewood emitting higher levels of particulate matter and carbon monoxide. Carbon monoxide concentrations during cooking were 6 times higher for firewood, 5 times higher for charcoal-gas, and 3 times higher for charcoal compared to WHO daily average limits. Additionally, a positive correlation between pollutant concentrations was noted (P-value = 0.0000). Lung problems 17.8% followed by eye irritation 15.7% were mentioned by those who claimed to know the health effects associated with cooking emissions. In addition, the spirometry test indicated that the majority of the participants had % predicted >80 while only 19% had % predicted below 50. CONCLUSION: Charcoal and firewood remain the primary cooking fuels in the study area despite their significant negative impacts. Our findings highlight a lack of awareness among community members regarding the health effects of biomass cooking emissions and insufficient guidance on constructing healthy kitchens. To address this, enforcing building standards, raising health awareness, and ensuring affordable access to modern fuels are crucial steps. These measures are essential for promoting healthier cooking practices and mitigating the adverse effects on households.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

Living systems must solve the problem of realizing their environment to act appropriately to maintain external relationships and internal order for survival and reproduction. This problem is a biological version of the philosophical enigma of how the self can escape solipsism. This study develops a comprehensive model to solve this adaptation problem. LSs must be composed of material entities that have the property of detecting their external states. The detection of the outside is conceptualized as “cognition,” a related state change that occurs at three levels of nested hierarchy: physical, chemical, and semiotic cognitions. Any entity that cognizes the surroundings is a “cognizer.” The hierarchical extension of cognition to all levels of the world provides a monistic view that only cognizers exist. Semiotic cognition is essential for the emergence and evolution of life. Living systems invented semiotic cognitions based on physical and chemical cognitions to manage the probability distribution of events that occur to them. This study proposes a theoretical model in which semiotic cognition is an adaptive process in which inverse causality operations produce particular internal states as symbols that signify hidden external states. This operation makes the living systems aware of the external world.

Spectacularly, particulate matter pollution influences human health by aggravating numerous diseases and causing premature deaths. In order to eliminate its concentration in the ambient air, plant species can act as natural bio-filters and capture, degrade, and metabolize air pollutants inside their foliage. In a study carried out at three sites with different pollution levels and plant types. The immobilization efficiency of Particulate Matter (PM) was investigated in the leaves of three species (shrub, climber, and herb) in the southwestern of Japan with a time gap of 14 days. Two healthy mature leaf samples of each specimen were carefully collected and analyzed using the gravimetric analytical method. A significant quantity of PM in three-size fractions with aerodynamic diameters ranging between (0.1-100 μm) was captured inside the leaf foliage of the analyzed species. Fine particles (2.5 -10 μm) dominated the highest portion of the PM deposition captured by the analyzed species with 70.6 μg.cm-2(39.5%). Shrub species represented with Elaeagnus pungens proved to be the most efficient species among the analyzed species. Leaf traits such as grooves, trichomes, roughness, and margin are considered key factors associated with positive PM deposition, whereas the total surface area of the leaves had no direct correlation to PM deposition.

Dissolved organic matter (DOM) derived from organic fertilizers may increase soil phosphorus (P) availability. However, the frequently observed correlation between soil P availability and dissolved organic carbon (DOC) content has led to an excessive focus on DOC content at the expense of DOM properties. The present study investigated the influence of DOM characteristics on soil P availability by using a 6-year field experiment and microcosms of P sorption in paddy soil. Our results showed that partial replacement of chemical P fertilizer with manure or crop straw increased P fertilizer-use efficiency, even when decreasing chemical P input by 34 %, compared to normal chemical fertilization. The microcosm experiment demonstrated that DOM properties, rather than total DOC content, determine soil P sorption capacity, despite the significant correlation between DOC content and P availability observed in the field experiment. Manure-DOM exerted stronger inhibitory effects on P sorption than straw-DOM, and high molecular weight (HMW)-fractionated DOM exerted stronger inhibitory effects on P sorption than low-molecular-weight-fractionated DOM by 16-20%. The mechanism was rooted in the HMW DOM with unique characteristics (e.g., strong aromaticity, hydrophobicity, abundant humic-like components, carboxyl groups, and benzene ring structures) competing for soil P sorption sites (e.g., reduction in specific surface area and micropore volume), decreasing the soil surface charge (e.g., zeta potential), and thereby suppressing P sorption in paddy soil. Our study points out a promising avenue for regulating organic matter properties with organic fertilization to improve P use efficiency in agricultural soils.

As broiler farming facilities have become larger and more concentrated in response to external environmental changes, there is a possibility of increased concentrations of fine dust and aerosols inside these facilities due to enclosure. In particular, workers are exposed to high concentrations of organic particulate matter and harmful gases while performing their tasks, and as they age, they become more vulnerable to respiratory diseases. It is essential to directly monitor the concen-trations to which workers are exposed, along with the spatial distribution of aerosols inside broiler house. In this study, we analyzed the regional aerosol concentrations using passive samplers in commercial tunnel-ventilated broiler farms. Simultaneously, we employed active samplers at the height of the workers' breathing zones to monitor real-time aerosol concentrations by particle size along their work routes. Spatial aerosol concentrations generally increased from the inlet to the exhaust in the breathing zone. The average aerosol concentrations were TSP -1,042 µg/m³, PM-10 718 µg/m³, and PM-2.5 137 µg/m³. To analyze the workers' exposure environments, we categorized the tasks in the barn into Static work period (SWP) and Moving work period (MWP) based on video analysis. The results showed that during MWP, fine dust concentrations exceeded the standards by up to 214%. Particularly, during MWP, the concentrations were 1.74 times higher for TSP, 1.40 times higher for PM-10, and 1.22 times higher for PM-2.5 compared to SWP. It was observed that during the movement of workers, physical generation of particles around 10 µm, such as feces, feed, and bedding, occurred due to the movement of chicken, which influenced the aerosol concentration.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

The lockdown implemented to tackle the spread of the COVID-19 pandemic had a positive impact on air quality. Globally, studies have shown that the air pollutants levels reduced temporally during the restriction measures. In this study, we evaluated the impact of COVID-19 restrictions on the air quality of Western Macedonia, Greece, using the hourly concentrations of PM2.5 and PM10 along with meteorological data from the Air Quality Monitoring Stations (AQMS) operated by the Lignite Center of Western Macedonia. In Western Macedonia, previous studies have identified that there is a general reduction in air pollutants levels during the last decade due to coal phase-out plan for power generation. During the lockdown the levels of PM2.5 and PM10 decreased further. However, reduced emissions from the local mining activities and lignite-fired power plant electricity generation, as well as the weather conditions seems to contribute to improving air quality.

Saussurea neoserrata Nakai offers a reliable and efficient source of antioxidants that can help alleviate adverse skin reactions triggered by air pollutants. Air pollutants, such as particulate matter (PM), have the ability to infiltrate the skin and contribute to the higher occurrence of cardiovascular, cerebrovascular, and respiratory ailments. Individuals with compromised skin barriers are particularly susceptible to the impact of PM since it can be absorbed more readily through the skin. This study investigated the impact of protocatechuic acid and syringin, obtained from the n-BuOH extract of S. neoserrata Nakai, on the release of PGE₂ and PGD₂ induced by PM₁₀. Additionally, it examined the gene expression of enzymes involved in the synthesis of PGE₂ and PGD₂ in human keratinocytes. The findings of this research highlight the potential of utilizing safe and efficient plant-derived antioxidants in dermatological and cosmetic applications to mitigate the negative skin reactions caused by exposure to air pollution.

ST-segment elevation myocardial infarction (STEMI), a major cause of mortality worldwide, has been shown through epidemiological studies to have a relationship with short-term exposure to air pollutants; however, the association between air pollutants and the outcome of STEMI has not been well studied. The aim of this study was to estimate the impact of air pollutants on the outcomes of STEMI. Data on particulate matter <2.5 μm (PM2.5), <10 μm (PM10), nitrogen dioxide (NO2), and ozone (O3) at each of the 11 air monitoring stations in Kaohsiung City were collected between January 1, 2012, and December 31, 2017. Medical records of non-trauma patients aged > 20 years who had visited the ED with a principal diagnosis of STEMI were extracted. The primary outcome measure was in-hospital mortality. After adjusting for potential confounders and meteorological variables, we found that an increase in the interquartile range (IQR) in NO2 was associated with an elevated risk of in-hospital mortality in patients with STEMI. Moreover, during the warm season, an IQR increase in NO2 corresponded to a higher risk of in-hospital mortality in patients with STEMI on lag 3 (OR=3.266; 95% CI:1.203–8.864, p=0.02). Conversely, an IQR increase in PM10 was associated with an increased risk of in-hospital mortality in patients with STEMI on lag 3 (OR=2.792; 95%CI:1.115–6.993, p=0.028) during the cold season. Our study suggests that exposure to NO2 (during warm season) and PM10 (during cold season) may contribute to a higher risk of poor prognosis in patients with STEMI.

Irrigation and fertilizer are two essential factors affecting rice root traits and yield. In this respect, a pot experiment was performed at the boro (dry season irrigated) season of 2021-22 in the Department of Agronomy of Bangladesh Agricultural University, Mymensingh, Bangladesh. The variety Binadhan-10 was planted at two irrigation conditions i.e. saturation (S) and continuous flooding (CF); two potassium (K) dose e.g. 65 kg ha-1 (K65) and 98 kg ha-1 (K98) and two nitrogen (N) dose i.e. 140 kg ha-1 (N140) and 210 kg ha-1 (N210). The experiment was laid in split plot design and replicated thrice. The findings confirmed the effectiveness of irrigation, K and N on root number (RN), root length (RL), root volume (RV), leaf area index (LAI), total dry matter (TDM), yield attributes and yield. Considering interaction among irrigation, K and N, S condition with K65 and N140 showed best performance. At 80 DAT, the highest RN (373.00), RL (1700.00 cm), RV (8.90 cm3 hill-1), LAI (4.94) and TDM (25.83 g plant-1) was obtained from this combination. Grain yield (GY) and root traits except root porosity, showed a significant positive association. Grain yield (GY) was highest (27.12 g pot-1) in S condition with K65 and N140.

Background & aims It is documented that low protein and amino-acid dietary intake is related to poorer cognitive health and increased risk of dementia. Degradation of the neuromodulatory pathways, (comprising the cholinergic, dopaminergic, serotoninergic and noradrenergic systems) is observed in neurodegenerative diseases and impairs the proper biosynthesis of key neuromodulators from micro-nutrients and amino acids. How these micro-nutrients are linked to neuromodulatory pathways in healthy adults is less studied. The Locus Coeruleus–Noradrenergic System (LC-NA) is the earliest subcortical structure affected in Alzheimer’s disease, showing marked neurodegeneration, but is also sensitive for age-related changes. The LC-NA system is critical for supporting attention and cognitive control, functions that are enhanced both by tyrosine administration and chronic tyrosine intake. The purpose of this study was to 1) investigate whether the dietary intake of tyrosine, the key precursor for noradrenaline (NA), is related to LC integrity 2) whether LC integrity mediates the reported association between tyrosine intake and higher cognitive performance (measured with Trail Making Test – TMT), and 3) whether LC integrity relates to an objective measure of brain maintenance (BrainPAD). Methods The analyses included 398 3T MRIs of healthy participants from the Berlin Aging Study II to investigate the relationship between LC integrity and habitual dietary tyrosine intake-daily average (HD-Tyr-IDA). As a control procedure, the same analyses were repeated on other main seeds of the neuromdulatory subcortical system (Dorsal and Medial Raphe, Ventral Tegmental Area and Nucleus Basalis of Meynert). In the same way, the relationships between the five nuclei and BrainPAD were tested. Results Results show that HD-Tyr-IDA is positively associated with LC integrity. Similarly, LC integrity disproportionally relates to better brain maintenance (BrainPAD). Mediation analyses reveal that only LC, relative to the other nuclei tested, mediates the relationship between HD-Tyr-IDA I and performance in the TMT and between HD-Tyr-IDA and BrainPAD. Conclusions These findings provide the first evidence linking tyrosine intake with LC-NA system integrity and its correlation with neuropsychological performance. This study strengthens the role of diet for maintaining brain and cognitive health and supports the noradrenergic theory of cognitive reserve. Within this framework, adequate tyrosine intake might increase the resilience of LC-NA system functioning, by preventing degeneration and supporting noradrenergic metabolism required for LC function and neuropsychological performance.

This paper is devoted to study the gravitational lensing for Curvature-coupled antisymmetric wormhole solution to compute the bending angle of light by utilizing the Gibbons and Werner technique. To achieve this, we find the Gaussian optical curvature and then apply Gauss-Bonnet theorem in the weak field limits. We also study the effects of plasma as well as dark matter mediums on the bending angle. Moreover, we analyze the graphical behaviour of the deflection angle $\alpha$ with respect to the impact parameter $\sigma$ and minimal radius $r_{0}$ in non-plasma and plasma mediums. We examine that deflection angle shows direct relation with $r_{0}$ such that large values of $r_{0}$ gives large deflection angle and small values of $r_{0}$ gives small deflection angle. For impact parameter $\sigma$, deflection angle $\alpha$ shows inverse relation. Additionally, we derive the deflection angle of light by using Keeton and Petters method and compare with the previous results.

Entomopathogenic fungi perform important functions in the ecosystem as natural antagonists of insects, which can be used in agriculture. Interestingly, recent studies showed a significant promotion of tested plants growth in the presence of fungi. We hypothesize that some of various compounds produced by entomopathogenic fungi can positively affect plant development. To test this hypothesis, fungal extracts of entomopathogenic fungus Beauveria bassiana were prepared at different conditions of temperature and pH. In addition to determination of the ammonium nitrogen content, the composition of extracts was analyzed by elemental ICP-OES. Then, their effect on the wheat germ growth was studied using various extract concentrations. After experiments, tested plants were measured, weighed, and the chlorophyll content was determined. Finally, the impact of extracts on the selected G+ and G- bacteria growth was examined to exclude the possibility of interference with soil microorganisms. The highest length of the wheat shoot was obtained for the use of 10-times diluted extract (10%) at pH 10 obtained at 20°C. In contrast, addition of 10% extract (pH 10) obtained at 75°C resulted in the shortest shoot. Generally, the extracts obtained at 75°C showed phytotoxic properties leading to lower values of shoot length and fresh weight in comparison to the control group. Our preliminary results are the first confirming the potential of fungal water extracts as factors promoting plant growth. Further detailed study should be carried out to confirm the effects in real environment conditions. Also, the consistency of the plant growth stimulation across different entomopathogenic fungi, and agriculturally used plant species should be tested.

The mission here is to see if we can find bound states for tachyons in some gravitational environment. That could provide an explanation for the phenomena called Dark Matter. Starting with the standard Schwarzschild metric in General Relativity, which is for a static and spherically symmetric source, it appears unlikely that such localized orbits exist. In this work the usual assumption of isotropic pressure is replaced by a model that has different pressures in the radial and angular directions. This should be relevant to the study of neutrinos, especially if they are tachyons, in cosmological models. We do find an arrangement that allows bound orbits for tachyons in a galaxy. This is a qualitative breakthrough. Then we go on to estimate the numbers involved and find that we do have a fair quantitative fit to the experimental data on the Galaxy Rotation Curve. Additionally we are led to look in the neighborhood of a Black Hole and there we find novel orbits for tachyons.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

Reducing the amount of precipitation in summer in the Chernozems area alters soil organic matter (SOM). To compensate for the lack of moisture, farmers are introducing new agricultural technologies such as no-till cultivation. In turn, no-till practices influence the composition of SOM. We examined the impacts of the rise of aridity and no-till technology on the chemical composition of bioavailable and recalcitrant pools of OM. The properties of SOM were assessed using double-shot pyrolysis with gas chromatography/mass spectrometry (GC/MS). The thermolabile substances that are volatilised in the first stage of pyrolysis (300°C) are considered the bioavailable pool. Accordingly, substances are obtained in the second pyrolysis stage (500°C) were attributed to the recalcitrant pool. Identified in both steps of pyrolysis, products were assigned to different chemical groups (lignin-derivative, polysaccharide-fragments, indoles, etc.) and relative abundances were calculated. In work for the separation of substances, a polar column was used for chromatography of the thermolabile fraction. With an increase in aridity in Сhernozems, the content in the bioavailable pool of polysaccharide fragments decreased and the proportion of indoles increased. In the recalcitrant pool, the abundance of six-membered rings with nitrogen and aromatic compounds decreases at the same time the contents of unsubstituted and O-substituted acyclic compounds as well as pyridine increases. The influence of the NT was more noticeable in the recalcitrant OM. The NT practice promotes biological activity and to rich in nitrogen compounds the bioavailable OM; this process contributes to the accumulation of carbon in the recalcitrant OM.

The scalar field of space-time film is considered as unified fundamental field. The field model under consideration is the space-time generalization of the model for a two-dimensional thin film. The force and metrical interactions between solitons are considered. These interactions correspond to the electromagnetic and gravitational interactions respectively. The metrical interaction and its correspondence to the gravitational one are considered in detail. The practical applications of this approach are discussed.

Land engineering is a specific new academic discipline in China. Although the undergraduate major of land engineering was officially approved and established lately since 2017, the birth of land engineering as an academic discipline dates back 40 years ago. It has passed through four development stages: the incubation stage in 1978-1985, the initial stage in 1986-1997, the growth stage in 1998-2011, and the expanding stage from 2012 to present. However, land engineering as an academic discipline remains immature and seriously lags behind practice. There are still no unified academic community and broad academic consensus. After a historical overview of the four development stages, this study gave a strategic consideration to five key questions. We argue that the study object of the discipline is land engineering activity, which is defined as the artificial transformation of a land complex combined by various natural and human elements. The uniqueness of the discipline is rooted in its ability to study the comprehensive and integrated reorganization or rebuilding of various elements of land as a complex, with the theory of land complex reconstruction being the core theory. The discipline of land engineering is based on land pure science and land technology, and is one basis of land management. It consists of two modules (rural land engineering and urban land engineering), five secondary disciplines of each module (land development, land rearrangement, land improvement, land protection, and land remediation), and more than 30 research directions. Various technologies are only instrumental but not essential components of land engineering as an academic discipline.

Mind and brain/matter interaction is one of the important and controversial issues in Islamic philosophy. In fact, in the resources of Islamic philosophy, one of the basic parts of philosophical discussions is related to mind’s nature and its interaction with the brain. Especially, in Avicenna’s philosophy, there are many articles and books which have addressed the topic of mind and brain and the relation between them. Avicenna was a profound philosopher, an expert physicist and a proficient physician of his time. Because of his experimental proficiency in medicine and surgery and his deep philosophical analysis, his discussion about mind and brain is very interesting for our time, due to recent advances in neuroscience. In this article, we have explained one of Avicenna’s arguments (in his famous opus “al-Isharat”) about the incorporeity of mind (self), which is very close to modern neuroscience and physics literature. In addition, we explain his model of mind and brain interaction. Avicenna described the mechanism of the causal effect of mind on the brain via a third identity, which works as an interface between them (in his main book “al-Shifa”). We try to illustrate his model by the use of some examples, inspired from modern physics. Also, we explore the philosophical constraints which must be considered in any model of mind-matter interaction, within the Islamic philosophy framework. In fact, we propose a new understanding of Avicenna’s philosophy which is in agreement with modern physics and neuroscience.