The aim of this study was to determine the extent to which the Tyme Wear smart shirt is as reliable and valid in detecting personalized ventilatory thresholds when compared to the Parvo Medics TrueOne 2400. In this validation study, 19 subjects were recruited to conduct two graded exercise test (GXT) trials. Each GXT trial was separated by seven to ten days of rest. During the GXT, gas exchange and heart rate data were collected by the TrueOne 2400 (TRUE) in addition to the ventilation data collected by the Tyme Wear smart shirt (S-PRED). Gas exchange data from TRUE was used to detect VT1 and VT2. TRUE and S-PRED VT1 and VT2 were compared to determine the reliability and validity of the smart shirt. Of the 19 subjects, data from 15 subjects were used during analysis. S-PRED exhibited excellent (ICC > 0.90) reliability for detection of VT1 and VT2 utilizing time point and workload and moderate (0.90 > ICC > 0.75 ) reliability utilizing heart rate. TRUE exhibited excellent reliability for detection of VT1 and VT2 utilizing time point, workload, and heart rate. When compared to TRUE, S-PRED appears to underestimate the VT1 workload (p > 0.05) across both trials and heart rate (p < 0.05) for trial 1. However, S-PRED appears to underestimate VT2 workload (p < 0.05) and heart rate (p < 0.05) across both trials. The result from this study suggests that the Tyme Wear smart shirt is less valid but is comparable in reliability when compared to the gold standard. Moreover, despite the underestimation of S-PRED VT1 and VT2, the S-PRED detected personalized ventilatory thresholds will provide an adequate training workload for most individuals. In conclusion, the Tyme Wear smart shirt provides easily accessible testing to establish threshold-guided training zones but does not devalue the long-standing laboratory equivalent.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Cross-contamination poses a pervasive challenge within the realm of food production. The propagation of infections is recognized to occur in an uncontrolled manner. Given the essential nature of food for human sustenance, the domain necessitates stringent control over contamination and cross-contamination due to the perilous potential for severe intoxication. In the context of managing biological contamination in fresh food items, commencing from production and extending to the final consumable, the utilization of chemicals must be judiciously limited to avert adverse effects. This biochemical approach, however, engenders environmental and health quandaries attributable to the incessant employment and discharge of such materials. The present research is centered upon demonstrating, at a laboratory scale, a process involving the leaching of plants, accompanied by the application of UVC irradiation during this procedure. This obviates the necessity for chemical solutions. The empirical findings showcased that subjecting the solution utilized for vegetable washing to UV irradiation rendered it 99 % microorganism-free in vegetables and 99.999% in the water component. This attests to efficacious decontamination, resource conservation, and mitigation of discharge-associated predicaments. The mathematical model precisely characterizes the behaviors manifested in the empirical data, thereby establishing a close correspondence with the kinetics law equation. Grasping the fundamental mechanisms and articulating them enables the enhancement of optimization and seamless integration of this approach to combat cross-contamination with heightened efficacy. This approach to addressing cross-contamination holds significant promise, underscoring its pivotal role in elevating food safety measures and ameliorating environmental repercussions. Envisioning the implementation of these practices at an industrial scale carries the potential to yield substantial dividends in terms of public health and sustainable practices

It is well established in literature that the public debt and economic growth bear positive and non-linear relationship. However, in recent literature, evidence of no causal relationship is found when accounted for endogeneity in case of advanced economies (Panizza & Presbitero, 2014). Chudik, Mohaddes, Pesaran, & Raissi, (2017) analyse the data on forty countries and find no evidence of universally applicable threshold effect in the relationship between debt and growth. These advancements in the debt-growth literature provides the motivation to re-explore the relationship between public debt and economic growth under non-linearity and endogeneity in context of developing economies of South Asia including Pakistan, India, Bangladesh and Sri-Lanka for the period 1980-2014. There exists a significant, positive but nonlinear relationship between the public debt and economic growth for the selected set of developing countries when accounted for endogeneity and non-linearity. The negative association between the public debt and economic growth for SAARC region is found when the debt level is higher than 61% of GDP which is quite lower than developed economies (90% of GDP). Individual threshold levels for debt-to-GDP ratio divulge that Sri Lanka, Pakistan and India need to control their public borrowings as their current debt levels are higher and/or around the respective threshold levels.

Then the purposes of this study were to compare and correlate the aerobic threshold (TH_aer) and anaerobic threshold (TH_anaer) measured during a new single judo specific incremental test and Treadmill Test for aerobic demand evaluation. Eight well-trained male competitive judo players (24.3±7.9 years; height of 169.3±6.7cm; fat mass of 12.7±3.9%) performed a maximal incremental specific test for judo mimicking the UchiKomi drills and on treadmill in different days. There was difference between specific and general TH_aer (P=0.0006) as well as weak correlation for TH_aer (r=0.32; R²=0.1; P=0.2) and TH_anaer (rs=-0.31; R²=0.1; P=0.12). When correlation was applied with normalized data (percentage of peak load) we observed moderate correlation for TH_aer (r=0.76; R²=0.58; P=0.027), but the same was not observed for TH_anaer. We conclude that there is a need of TH_aer and TH_anaer evaluation through a specific test for Judo.

Achieving high economic growth rate while maintaining low inflation rate, has become the main objective of monetary authorities all over the world. Indeed, empirical literature reflects that high inflation rates are detrimental to long run growth and entail welfare costs. To achieve this objective, central banks have availed different options from time to time which include inflation targeting. Monetary authorities in Tanzania have been targeting an inflation level of around 5 percent per annum for economic policy purposes. However, when high inflation is to be controlled, tight monetary policy is put in place which might in turn affect the economic activity. Also, the Tobin effect suggests that inflation causes individuals to substitute out of money and into interest earning assets, which leads to greater capital intensity which in turn promotes economic growth. Against these major points, this paper examines a non linear relationship between inflation and economic growth using both a quadratic and threshold endogenous models and attempts to identify the existence of threshold effects between these variables. The paper uses a data set spanning from 1967 to 2015. The most interesting finding of the estimations is that the estimated coefficient of the linear term of inflation is negative while the estimated coefficient of the square term of inflation is positive, suggesting a U-shaped effect as opposed to inverse or inverted U-shaped relationship found in other countries by previous studies. These results suggest that the Tobin effect may be valid for high inflation, in which people strongly realize the importance of substituting money for interest-bearing assets. This leads to an increase in capital investment, and in turn, an increase in economic growth even with high inflation rate. However, this U-shaped relationship between inflation and economic growth suggests that, the economy is better off at extremely low inflation episodes. The optimal inflation rate that ranges between 3.25 percent and 3.75 percent is obtained by minimizing the residual sum of squares and/or maximizing adjusted R-squared. These findings have some policy implications for the policymakers and development partners. The paper is consistent with policy suggestions by international agencies. Efforts to minimize inflation to a very low level are likely to have a positive effect on economic growth.

We experimentally study the supercontinuum (SC) induced by femtosecond filament in different liquid media, and determine the relative measurement value of filamentation threshold Pth for these media by using a Mach-Zehnder interferometer (MZI). It is found that the value of Pth is higher than the critical power for self-focusing Pcr, which can be attributed to the strong dispersion effect. Changing the focal length of the focusing lens affect the measured results of the filamentation threshold: In the case of shorter focal length, linear focusing (i.e., geometrical focusing) regime dominates, and the measured values of Pth for different media are almost the same; as the focal length becomes larger, self-focusing starts to play a role, making the values of Pth for different media different from each other. This work provides an effective approach to study the femtosecond filamentation process in liquid media, and helpful to further understand the physical process of supercontinuum induced by femtosecond filament in liquid media.

Astringency is an important sensory characteristic of food and beverages containing polyphenols. However, astringency perception in elderly people has not been documented. The aim of the present work was to evaluate sensitivity to astringency as a function of age and salivary flow. Fifty-four panellists, including 30 elderly people (age=75±4.2 years) and 24 young people (age=29.4±3.8 years), participated in this study. Astringency sensitivity was evaluated by the 2-alternative forced choice (2-AFC) procedure using tannic acid solutions. Whole saliva was collected for 5 min before and after sensory tests. The results showed that the astringency threshold was significantly higher in the elderly group than in the young group. Moreover, a negative correlation between salivary flow and threshold was observed in the young group only. These results showed a difference in oral astringency perception as a function of age for the first time. This difference can be linked to salivary properties that differ as a function of age.

Background: Traditional omic analysis relies on p-value and fold change as selection criteria. There is an ongoing debate on their effectiveness in delivering systemic and robust interpretation, due to their dependence on assumptions of conformity with various parametric distributions.Here, we propose a threshold-free selection method based on robust, non-parametric statistics, ensuring independence from the statistical distribution properties and broad applicability. Such methods could adapt to different initial data distributions, contrary to statistical techniques based on fixed thresholds. Methods: Our work extends the Rank Products methodology with a neutral selection method of high information-extraction capacity. We introduce the calculation of the RP distribution’s entropy to isolate the features of interest by their contribution to the distribution’s information content. The aim is a methodology performing threshold-free identification of the differentially expressed features, which are highly informative about the phenomenon under scrutiny. Conclusions: Applying the proposed method on microarray (transcriptomic and DNA methylation) and RNAseq count data of varying sizes and noise presence, we observe robust convergence for the different parameterisations to stable cutoff points. Functional analysis through BioInfoMiner and EnrichR was used to evaluate the information potency of the resulting feature lists. Overall, the derived functional terms provide a systemic description highly compatible with the results of traditional statistical hypothesis testing techniques. The methodology behaves consistently across different data types. The feature lists are compact and information-rich, indicating phenotypic aspects specific to the tissue and biological phenomenon i nvestigated. Selection by information content measures efficiently addresses problems, emerging from arbitrary thresholding, thus facilitating the full automation of the analysis.

The ability to smell is crucial for most species as it enables the detection of environmental threats like smoke, fosters social interactions, and contributes to the sensory evaluation of food and eating behavior. The high prevalence of smell disturbances throughout the life span calls for a continuous effort to improve tools for quick and reliable assessment of olfactory function. Odor-dispensing pens, called Sniffin' Sticks, are an established method to deliver olfactory stimuli during diagnostic evaluation. We tested the suitability of a Bayesian adaptive algorithm (QUEST) to estimate olfactory sensitivity using Sniffin' Sticks by comparing QUEST sensitivity thresholds with those obtained using a procedure based on an established standard staircase protocol. Thresholds were measured twice with both procedures in two sessions (Test and Retest). Overall, both procedures exhibited considerable overlap with QUEST displaying slightly higher test-retest correlations, less variability between measurements, and reduced testing duration. Notably, participants were more frequently presented with the highest concentration during the QUEST which may foster adaptation and habituation effects. We conclude that further research is required to better understand and optimize the procedure for assessment of olfactory performance.

The one-dimensional gas of bosons interacting via a repulsive contact potential was solved long ago via Bethe's ansatz by Lieb and Liniger [Phys. Rev. {\bf 130}, 1605 (1963)]. The low energy excitation spectrum is a Luttinger liquid parametrized by a conformal field theory with conformal charge $c=1$. For higher energy excitations the spectral function displays deviations from the Luttinger behavior arising from the curvature terms in the dispersion. Adding a corrective term of the form of a mobile impurity coupled to the Luttinger liquid modes corrects this problem. The ``impurity'' term is an irrelevant operator, which if treated non-perturbatively, yields the threshold singularities in the one-particle and one-hole hole Green's function correctly. We show that the exponents obtained via the finite size corrections to the ground state energy are identical to those obtained through the shift function.

Magnetorheological processing was applied to polish the working surfaces of the ZnGeP2 single crystal, in which a non-aqueous liquid with magnetic particles of carbonyl iron with the addition of nanodiamonds was used. Samples of a single crystal ZnGeP2 with an angstrom level of surface roughness were received. the use of MRP has allowed more accurately characterizing possible structural defects that have emerged on the surface of a single crystal and have a size of ~ 0.5-1.5 μm. the LIDT value at the indicated or-ders of magnitude of the surface roughness parameters is determined not by the quality of polishing, but by the number of point depressions caused by physical limitations of the structural configuration of the crystal volume. These results are in good agreement with the assumption made about a significant effect of the concentration of dislocations in a ZnGeP2 crystal on LIDT.

This research paper aimed to examine the impact of exchange rate volatility on South Africa's exports from 1994 Q1 to 2023 Q2. The study used the Augmented Dickey-Fuller (ADF) and Phillips-Perron (PP) tests to test for stationarity. The nonlinear autoregressive distributed lag (NARDL) model and smooth threshold regression (STR) are employed to analyse the relationship between exchange rate volatility and exports. The GARCH (1.1) technique is used to construct the exchange rate volatility data. The results of the stationarity tests reveal that variables are either integrated in order I(0) or I(1). This implies that the variables used in this study are stationary, which is crucial for conducting accurate analyses. Moreover, the NARDL test approach provided insights into the long-run effects of exchange rate volatility on South Africa's exports. Based on the NARDL test, positive shocks have a greater but statistically insignificant effect on exports than negative shocks. Therefore, a greater level of exchange rate volatility may lead to increased exports from South Africa. Furthermore, the STR also reveals that the impact of exchange rate volatility is insignificant. These findings provide valuable insights for policymakers and firms to make informed decisions regarding exchange rate management and export strategies in South Africa.

The stability and optimal control for an SIS epidemic model with demographics and heterogeneous control strategies (immunization and quarantine) on complex networks are investigated. The epidemic threshold, disease-free and endemic equilibria are derived. Then, global asymptotical stability about the two equilibria are studied based on different methods. Furthermore, the optimal control issue about the system is also considered. We obtain the existence and uniqueness of the optimal control and optimal control tactics. Some numerical simulations were conducted to illustrate and supplement the theoretical results. Meanwhile, the effects of the combination of various immunization and quarantine schemes are studied and also compared with the optimal control strategies.

Fiber aggregation in nanocomposites has an important effect on the macroscopic electrical performance. To quantitatively evaluate its effect, an index to characterize the degree of aggregation is imperative, and ideally it should have three features simultaneously, i.e., single-parametric, dimensionless and physically meaningful, applicable to different aggregation topologies, and one-to-one corresponding to material electrical properties. To this end, a new aggregation degree is proposed, which is defined as the average increased number of fibers that connect with each one when fibers aggregate from a uniformly distributed state. This index is applicable to different aggregation topologies from lump-like aggregating clusters to network-like aggregating clusters. This index is proven to only depend on the local features of aggregating clusters, and can be concisely expressed by the characteristic parameters of local structure, via geometric probability analysis and numerical validations. Further, a one-to-one linear relation between the aggregation degree and percolation threshold is established by Monte Carlo simulations, which is independent of the distribution law of the fibers. This work provides a guide to the property characterization, performance prediction and material design of nanocomposites, and also gives a physical insight into the understanding of systems with similar non-uniform distributions.

Taste and smell function decline with age, with robust impairment in the very old. Much less is known about taste and smell function in young and middle old. We investigated taste and smell sensitivity via thresholds in a sub-sample of the NutriAct Family Study (NFS), the NFS Examinations cohort (NFSE; N=251, age M=62.5 years). We examined different aspects relating to taste and smell function: the degree to which taste and smell sensitivity relate to another and to taste and smell preferences, the role of gender and age, as well as effects on Quality of Life (QOL). Taste thresholds were highly correlated but no correlation was observed between taste and smell thresholds and between thresholds and preference. Women were more sensitive for both taste and smell than men. We found no effect of age on sensitivity and no effect of sensitivity on QoL. All null-findings were corroborated with Bayesian statistics providing evidence for the null hypotheses. Together our results indicate the independence of taste and smell despite their overlap during sensorial experiences. We found no evidence for age-related sensory decline, which could be due to our sample´s characteristics of non-clinical volunteers with good dental health and 93% non-smokers.

In this article we have presented a new perception of herd immunity threshold (HIT) which considers that only a “band of population” are susceptible to any pathogenic infection. This is termed as the “effective herd immunity threshold” (EHIT) and the progression of the disease (caused by this pathogenic infection) is mainly determined by this EHIT value. We have argued here that this EHIT value (considering the immunity band picture in the population) will be substantially lower than the estimated canonical HIT values obtained from various existing models. We propose that the actual prediction of the disease progression should now be calculated using the EHIT values.

Rapid development of high-throughput omics technologies generates an increasing interests in algorithms for cutoff point identification. Existing cutoff methods and tools identify cutoff points based on association of continuous variables with another variable, such as phenotype, disease state or treatment group. These approaches are not applicable for descriptive studies in which continuous variables are reported without known association with any biologically meaningful variables. The most common shape of the ranked distribution of continuous variables in high-throughput descriptive studies corresponds to a biphasic exponential/super-exponential curve, where the first phase includes big number of variables with values slowly growing with rank and the second phase includes smaller number of variables rapidly growing with rank. This study describes an easy algorithm to identify the boundary between these phases to be used as a cutoff point. The major assumption of that approach is that small number of variables with high values dominate biological system and determine its major processes and functions. This approach was tested on three different datasets: genes in the human cerebral cortex, mammalian genes sensitive to chemical exposures, and proteins expressed in human heart. In every case, the described cutoff identification method produced shortlists of variables (genes, proteins) highly relevant for dominant functions/pathways of the analyzed biological systems. Thus, our described method for cutoff identification may be used to prioritize variables for a focused functional analysis, in situations where other methods of dichotomization of data are inaccessible.

(1) Background: Globally, neck pain is prevalent, affecting around thirty percent of the population annually. To better understand the influence of pain on the myofascial layers, the present study investigated these on the upper trapezius muscle in unilateral, more severe neck pain. (2) Methods: This study was a cross-sectional study. Forty patients (42.2 ± 14.7) with a confirmed diagnosis of unilateral neck pain were examined using durometry and indentometry. The study evaluated stiffness, elasticity, and pressure pain threshold of both sides of the neck (symptomatic side: SS; healthy side: HS). Furthermore, the range of motion of the cervical spine (lateral flexion, rotation) was quantified using a digital goniometer. (3) Results: A significant lateral discrepancy was observed in stiffness between groups (durometry: SS – 33.76 ± 7.78, HS – 29.75 ± 7.45, p<0.001; indentometry: SS – 59.73 ± 33.93, HS – 4.18 ± 12.69, p=0.024). In contrast, no differences were found between the comparison sides of the upper trapezius for the parameter’s elasticity (SS – 0.101 ± 1.09, HS – -0.006 ± 0.29, p=0.416), cervical spine mobility (lateral flexion: SS – 37.08 ± 8.15, HS – 37.73 ± 7.61, p=0.559; rotation: SS – 73.55 ± 12.37, HS – 72.85 ± 11.10, p=0.660) and algometry (SS – 36.41 ± 17.53, HS – 37.22 ± 17.00, p=0.657). (4) Conclusion: Overall, it can be concluded that more severe neck pain unilaterally shows differences in stiffness on the same side. Future research is needed to investigate the links.

(1) Background: The influence of the menstrual cycle on physical fitness in athletes is controversial in the scientific literature. There is a marked fluctuation of sex hormones at three key points of the menstrual cycle, where estrogen and progesterone vary significantly. Hormonal contraception induces hormonal levels different from the natural menstrual cycle, requiring specific study in relation to physical fitness. (2) Method: Women aged 18 to 40 years with regular natural menstrual cycles and women using hormonal contraception were recruited, creating two study groups. All participants needed to be athletes classified as level II-III according to the classification by McKay et al (2021), based on training volume/physical activity metrics, among other variables. To assess their physical fitness, Cardiorespiratory Fitness (measured by VO2max), high-speed strength, hand grip strength, and flexibility were evaluated. Blood samples were taken to determine the menstrual cycle phase through analysis of sex hormone levels. Additionally, urine tests for ovulation detection were performed for the natural menstrual cycle group. Neurosensory stimulation tests were incorporated to measure sensory threshold and pain threshold in each phase. Body composition in each phase and its relationship with the other variables were also taken into account. (3) Results: Athletes in the natural cycling group showed differences in VO2max (mL·kg-1·min-1) (phase I =41.75 vs phase II =43,85 and (p=0.004) and phase I vs phase III=43,25 mL·kg-1·min-1 (p =0.043)), as well as in body weight (phase I = 63.23 vs. phase III = 62.48 kg; p=0.006), first pain threshold (phase I = 1.34 vs. phase II = 1.69 (p=0.027) and phase III = 1.59 mA (p=0.011)), and sensitive threshold (phase I = 0.64 vs. phase II = 0.76 mA (p=0.017)). The pain threshold was found to be an important covariate in relation to VO2max, explaining 31.9% of the variance in phase I (p=0.006). These findings were not observed between the two phases of contraceptive cycling. (4) Conclusion: The natural menstrual cycle will cause significant changes in the physical fitness of athletes. The use of hormonal contraception is not innocuous. Women with natural cycles show a decrease in cardiorespiratory fitness in phases II and III, which is a factor to be considered in relation to training level and workload.

Background: Despite hearing aids adequately compensate for hearing loss, a substantial proportion of the population leave their hearing difficulties untreated. Even though this is a well-known clinical issue, the optimal approach to address this issue during the hearing rehabilitation process is still unclear. Purpose: The present study aims to characterise behavioural and neurophysiological auditory and cognitive processing skills in experienced hearing aid users versus those with normal hearing, aimed at providing clinicians with the evidence required to adequately manage the expectations of their clients, thus indirectly reinforcing hearing-aid adoption within the adult population with hearing loss. Research design: Behavioural tests included auditory, cognitive, and speech-in-noise tasks; and neurophysiological testing included cortical auditory evoked potentials evoked by a /da/ stimulus presented at 65 dB SPL. The tests were selected based on previous literature supporting specific speech-understanding skills. Study sample: Ten participants (7 female, 21—68 years) with bilateral, mild-moderate to moderately-severe sensorineural hearing loss (HL), and 10 with clinically normal hearing (NH, 8 female, 19—62 years) participated in the study. Data collection and analysis: Behavioural data was analysed using multivariate analysis of variance (MANOVA) and neurophysiological analysis used measurements such as independent t-test, time-frequency analysis and inter-trial phase coherence. Results: The NH and HL groups presented similar scores in all the behavioural tasks. Time-frequency analysis revealed a statistically significantly reduction in alpha (8–12 Hz) synchronisation at the centro-frontal electrodes in the HL group – a brain activity pattern that has been associated with listening effort, inhibition and selective attention. Conclusions and significance: Results support the conclusion that hearing aids are effective in compensating for the audibility of their users, enabling them to perform at similar levels than their normal-hearing peers. However, the reduced alpha synchronisation observed in the HL population indicates that adequate audibility does not extend to improved neural responses. Future studies need to investigate the induced activity in speech understanding paradigms to explore the auditory processing differences at cortical level. The results are only from a small sample size but the findings have the potential to support clinicians in managing adequately the expectations of their clients in regards the benefits of hearing aid technologies.

Nociceptive threshold (NT) testing is widely used for the study of pain and its alleviation. The end point is a normal behavioural response which may be affected by restraint or unfamiliar surroundings leading to erroneous data. Remotely controlled thermal and mechanical NT testing systems were developed to allow free movement during testing and were evaluated in cats, dogs, sheep, horses and camels. Thermal threshold (TT) testing incorporated a heater and temperature sensor held against the animal’s shaved skin. Mechanical threshold (MT) testing incorporated a pneumatic actuator attached to a limb containing a 1 - 2mm radiused pin pushed against the skin. Both stimuli were driven from battery powered control units attached on the animal’s back, controlled remotely via infra-red radiation from a hand held component. Threshold reading was held automatically and displayed digitally on the unit. The system was failsafe with a safety cutout at a preset temperature or force as appropriate. The animals accepted the equipment and behaved normally in their home environment enabling recording of reproducible TT (38.5 – 49.8°C) and MT (2.7 – 10.1N); precise values depended on species, the individual and the stimulus characteristics. Remote controlled NT threshold testing appears to be a viable refinement for pain research.

In the last years, the development of low-cost GNSS sensors allowed monitoring in a continuous way movement related to natural processes like landslides with increasing accuracy and limited efforts. In this work, we present the first results of an experimental low-cost GNSS continuous monitoring applied to the unstable slope affecting the Madonna del Sasso Sanctuary (NW Italy). The courtyard of Sanctuary is built of two unstable blocks delimited by high cliff. Previous studies and non-continuous monitoring showed that blocks suffer a seasonal cycle of thermal expansion and long-term trend to downslope of few millimeters per year. The presence of continuous monitoring solution, could be an essential help to better understand the kinematics of unstable slope and to recognize the beginning of a possible paroxysm phase that could end with a failure of the unstable area. We tested the accuracy of the instruments and the first year of experimental measurements are presented. We also propose a methodological approach that considers the use of automatized procedures for the identification of anomalous trends and a risk communication strategy based on monitoring data.

The relationship between economic growth, growth volatility and financial sector development continues to attract attention in the theoretical and empirical literature. Over time, some studies hypothesize that finance has a causal linear relationship with growth. Recently several other authors contradict this claim and argue that the relationship that exists between finance and growth is nonlinear. We investigate these claims for Nigeria for the period between 1970 and 2015, using semi-parametric econometric methods, Hansen sample splitting techniques and threshold estimator. We observed no evidence of ‘Too much finance’ as claimed by many researchers in recent times. We show that the relationship between financial development and economic growth is U-shaped. This is equally true for the relationship between financial development and growth volatility. We also discuss policy implications of our findings and recommend financial innovations and decentralization of stock exchanges to boost access to financial services, in addition, improved regulation to enhance financial market efficiency.

During routine bridge maintenance, edge detection allows the partial condition of the bridge to be viewed. However, many edge detection methods often have unsatisfactory performances when dealing with images with complex backgrounds. Moreover, the processing often involves the manual selection of thresholds, which can result in repeated testing and comparisons. To address these problems in this paper, the wavelet transform modulus maxima method is used to detect the target image, and then the threshold value of the image can be determined automatically according to the OTSU method to remove the pseudo-edges. Thus, the real image edges can be detected. The results show that the information entropy and SSIM of the detection results are the highest when compared with the commonly used Canny and Laplace algorithms, which means that the detection quality is optimal. To more fully illustrate the advantages of the algorithms, images with more complex backgrounds were detected and the processing results of the algorithms in this paper are still optimal. In addition, the automatic selection of thresholds saves the operator’s effort and improves the detection efficiency. Thanks to the combined use of the above two methods, detection quality and efficiency are significantly improved, which has a good application in engineering practice.

Backgrounds Linear association has widely been assumed for prediction of aging-related fractional anisotropy (FA) decline in white matter of the brain. While useful for testing significance of the aging effect, it fails to identify a threshold age before and after which the age-FA association changes. Identification of such a threshold is often of clinical interest for timely intervention. Methods We employed a sigmoidal growth function to test a threshold effect in age triggering onset of cerebral decline in 21 white matter tracts, and compared its fitting performance to those of linear, and power regression. The study sample was a normal healthy cohort of 106 participants with ages in mid-life ranging from 18 to 60 years. Results Of the 21 white matter tracts analyzed, the posterior thalamic radiation showed better fit with sigmoidal curve model, compared to a linear or power regression. The estimated threshold age in years (95% confidence interval) were 47.2 (44.1-48.4). Conclusion While available evidence regarding the presence of a specific age threshold for cerebral decline in mid-life based on FA was limited, the posterior thalamic radiation exhibited a threshold age of 47.2. Beyond this age point, we observed a significant change in the FA risk pattern.

In offshore drilling, accidents such as gas invasion, overflow, and kicks are inevitable, and they can escalate into blowouts and other catastrophic events that result in casualties and substantial economic losses. Therefore, maintaining drilling safety requires accurate monitoring of gas invasion and overflow. The majority of overflow monitoring methods currently utilized at drilling sites are threshold-based. However, monitoring parameters acquired during actual drilling operations frequently contain noise signals, making it difficult for threshold-based methods to strike a balance between improving accuracy and minimizing false positives. In this paper, Pattern Recognition-based Kick Detection (PRKD) is proposed as a novel method for diagnosing overflow in offshore drilling. This method utilizes the overflow evolution process by integrating multi-phase flow calculations, data filtering theory, pattern recognition theory, the Bayesian framework, and other theoretical models. The PRKD effectively detects and monitors gas intrusion and overflow based on single parameters by analyzing the shape and wave characteristics of the curves. The case analysis demonstrates that the proposed method for monitoring drilling overflow achieves high precision while maintaining a low false positive rate. By combining advanced computational techniques with pattern recognition algorithms, the PRKD improves the accuracy and reliability of kick detection, enabling proactive responses to potential risks, protecting the environment and human lives, and optimizing drilling operations.

: This study investigates the use of various thunderstorm indices in predicting severe thunderstorms events during the monsoon season in four different regions in India. The research evaluates the performance of the prediction model using a model skill score and utilizes the Weather Research and Forecasting (WRF) model with the double moment microphysics scheme to simulate model cases. It also compares fifteen thunderstorm indices derived from the ERA5 dataset to identify the most effective index for predicting severe thunderstorms events. The results of this study show that in-corporating thunderstorm indices with model skill scores improves severe thunderstorms fore-casting in the monsoon season in India. The result revealed that determining the optimal threshold for each index is crucial in achieving accurate predictions. The study also highlights the importance of considering multiple indices rather than relying on a single index to predict severe thunderstorms events. The advance indices such as Energy Helicity Index (EHI), Supercell Composite Parameter (SCP), mainly works well with extreme severe thunderstorms. The simplistic indices can predict the weak or severe thunderstorm easily. The use of multiple thunderstorm indices can also help mete-orologists to make more accurate predictions, which can further enhance public safety. In conclu-sion, this study demonstrates the potential of incorporating thunderstorm indices with model skill scores like HSS and TSS and combinations of different skill scores in severe thunderstorms fore-casting during the monsoon season in India. Future research can build upon the findings of this study to develop more accurate and reliable severe weather forecasting models.

The results of experimental studies of ohmic conductivity degradation in the ensembles of nanostructured anatase bridges under long-term effect of direct current are presented. Stochastic sets of interelectrode partially conducting bridges consisting of close-packed anatase nanoparticles were formed by the seeding particles from drying aqueous suspensions on the surfaces of silica substrates with interdigital platinum electrodes. Multiple-run experiments at room temperature have shown that ohmic conductivity degradation in these systems is irreversible. It is presumably due to accumulated capture of conduction electrons by deep traps in anatase nanoparticles. The scaling analysis of voltage drops across the samples at the final stage of degradation gives a critical exponent for ohmic conductivity as 1.597. This value satisfactorily agrees with the reported model data for percolation systems. At an early stage of degradation, the spectral density of conduction current fluctuations wihin the frequency range of 0.01 Hz - 1 Hz decreases approximately as , while near the percolation threshold the decrease trend changes to . This transition is interpreted in terms of an increasing contribution of blockages and subsequent avalanche-like breakdowns of part of the local conduction channels in the bridges into electron transport near the percolation threshold.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Sustainable development (SD) is essential to reduce and mitigate climate change impacts, environmental deterioration and to increase social sustainability. SD is therefore highly relevant for the engineering profession and is today found integrated with the higher education of specific engineering programs. This paper investigated the knowledge of SD for students entering the master’s program in Sustainable Building Information Management (BIM) by comparing levels of knowledge at the start and end of the first course Sustainability, Analyses and Simulations. The level of knowledge of SD was analyzed by classifying students’ conceptions of sustainability using SOLO taxonomy and the spectrum of liminality and the threshold concept. Students written responses to the question “What do you know about sustainability?” and written group project reports were used for analyzing levels of knowledge of SD. Levels of knowledge of SD was classified as pre (pre-liminal or pre-structural); uni-structural, multi-structural, relational and post-stages (extended abstract or post-liminal). In total, 68% of the students entering the master’s program in 2017 and 88% in 2018 showed a pre-structural, uni-structural and multi-structural SD knowledge. In general, few students entering the program showed relational and post-stages of SD knowledge, 32% and 12% of the students in 2017 and 2018, respectively. The students at the post-stage were able to express themselves more individually and creatively compared to previous levels in that they could connect the dimensions of SD to the context of SD of buildings, but also argue why SD of buildings was important and they could also suggest actions or tools for improved SD that engineers should use. Only one group of five (in 2017) showed a post-stage level of knowledge in the group project report. It is likely that the student’s general approach to the work with the reports was to mainly cope with the course requirements which is a sign of surface approach to learning. It, therefore, seems reasonable that future developments of the course should ensure that the students use the scientific literature in their group project reports to make it easier for them to understand the relationship between software use and the connection to green buildings certificate systems and SD of buildings. By making it mandatory to include scientific literature in the reports the students will be encouraged to read and think critically, and deeper, and to put the practical implementation of the software analysis results into a scientific context of SD and BIM.

This article presents a new method of segmenting grayscale images by minimizing Shannon's neutrosophic entropy. For the proposed segmentation method, the neutrosophic information components, i.e., the degree of truth, the degree of neutrality and the degree of falsity are defined taking into account the belonging to the segmented regions and at the same time to the separation threshold area. The principle of the method is simple and easy to understand and can lead to multiple thresholds. The efficacy of the method is illustrated using some test gray level images. The experimental results show that the proposed method has good performance for segmentation with optimal gray level thresholds.

A long-term investigation of D. suzukii dynamics in wild blueberry fields from 2012 - 2018 demonstrates relative abundance is still increasing seven years after initial invasion. Relative abundance is determined by physiological date of first detection and air temperatures the previous winter. Date of first detection of flies does not determine date of fruit infestation. The level of fruit infestation is determined by year, fly pressure, and insecticide application frequency. Frequency of insecticide application is determined by production system. Non-crop wild fruit and predation influences fly pressure; increased wild fruit abundance results in increased fly pressure. Increased predation rate reduces fly pressure, but only at high abundance of flies, or when high levels of wild fruit are present along field edges. Male sex ratio might be declining over the seven years. Action thresholds were developed from samples of 92 fields from 2012 - 2017 that related cumulative adult male trap capture to the following week likelihood of fruit infestation. A two-parameter gamma density function describing this probability was used to develop a risk-based gradient action threshold system. The action thresholds were validated from 2016-2018 in 35 fields and were shown to work well in two of three years (2016 and 2017).

This paper utilizes dynamic panel threshold technology to conduct a nonlinear test on the direct effect between environmental regulation and economic fluctuations and the effect of industrial structure upgrading by taking 35 industrial sectors in China from 2003 to 2016 . The research has found that there is an inverted "U" relationship between environmental regulation and economic fluctuations, with the enhancement of environmental regulations, the economic fluctuation increases first and then decreases. The cross-terms of environmental regulation and industrial structure rationalization or industrial structure upgrading are significantly negative, which indicates that the enhancement of environmental regulation is conducive to promoting industrial structure upgrading and reducing the economic fluctuations. While the rationalization factors of industrial structure and advanced industrial structure are significantly negative, indicating that both forms of industrial structure upgrading are conducive to reducing the economic fluctuations. Environmental regulation has technical innovation thresholds for industrial structure upgrading and economic fluctuations, but there are no human capital or FDI thresholds. In the rationalization model of industrial structure, there is a nonlinear "U" relationship between environmental regulation and economic fluctuations when the proportion of scientific research expenditure is more than 1.35%. With the enhancement of environmental regulation, the economic fluctuation reduces first and then increases, and the corresponding inflection point value is 2.398% of the environmental regulation level. At the same time, the environmental regulation can indirectly reduce economic fluctuations by pushing down the industrial structure upgrades. In the advanced model of industrial structure, there is a “U” relationship between environmental regulation and economic fluctuation when the proportion of scientific research expenditure is greater than 1.26%. With continuous enhancement of environmental regulation, the economic fluctuation reduces first and then increases. The corresponding inflection point value is 1.78% of the environmental regulation level, and environmental regulation can indirectly reduce economic fluctuations by promoting the industrial structure at the same time.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

In response to the new concept of the impact of total climate production factors on plant phenology, this study will verify the feasibility of simulating plant phenology and triggering thresholds based on total climatic production factors by using the phenological and meteorological observation data of S. krylovii plant from 1985 to 2018 at the Xilinhot National Climate Observatory of China Meteorological Administration. The results indicate that the total climate production factors influencing plant phenological changes can be well used for phenological simulation and its triggering thresholds. The mutation of cumulative climate production potential based on total climate production factors can effectively indicate the green-up date and the wilting date of S. krylovii plant, and their triggering thresholds depend on the parameters of climate resource change and plant biology, which are (0.085, –5.363) and (0.086, –27.620), respectively. The cumulative climate production potential based on total climate production factors can effectively indicate the heading date of S. krylovii plant, and its triggering thresholds also depends on the parameters of climate resource change and plant biology, which is (394.632，–38026.268). Furthermore, the results support the viewpoint that the climate abrupt changes determine the beginning and the ending of plant growth, while the accumulative climate resources determine the other phenological dates. This study provides new ideas for the study of plant phenology.

Background: Identifying a specific threshold level of SARS-CoV-2 antibodies that confers protection in immunocompromised patients has been very challenging. The aim was to assess the threshold of 264 binding antibody units (BAU)/ml using four different SARS-CoV-2 antibody assays (Abbott, Beckman, Roche, and Siemens) and to establish a new optimal threshold of protection for each of the four antibody assays. Methods: This study was performed on data retrieved from 69 individuals, who received at least one dose of the Pfizer/BioNTech BNT162b2 or Moderna COVID-19 vaccine (Spikevax) at the Alphabio Laboratory in Marseille, France (European Hospital, Alphabio – Biogroup). The results were compared to the percent inhibition calculated using a functional surrogate of a standardized virus neutralization test (Genscript). Results: Samples from 69 patients were analyzed. For a reference cutoff of 264 BAU/ml, assays showed moderate to good overall concordance with Genscript: 87% concordance for Abbott, 78% for Beckman, 75% for Roche, and 88% for Siemens. Overall concordance increased consistently after applying new thresholds, i.e., 148 BAU/ml (Abbott), 48 (Beckman), 559 (Roche), and 270 (Siemens). Conclusion: We suggest specific adjusted thresholds (BAU/ml) for the four commercial antibody assays that are used to assess pre-exposure prophylaxis in immunocompromised patients.

Economists have long been interested in examining inflation-growth nexus. Nevertheless, the nature of their relationship and the optimal level of inflation threshold for economic growth have still remained controversial in both theoretical and empirical works. Accordingly, this study investigates the existence of threshold effects of inflation on economic growth in Ethiopia over the period 1975-2018 using a Two-regime Threshold Auto-regressive (TAR) model. The study mainly departs from previous works since it estimates sector-specific inflation threshold level in food and non-food sectors. Our preliminary analyses clearly reveal that inflation in food sector has become more volatile, less-persistent and key contributor to the general inflation as compared to its non-food counterpart. Further, The TAR model results and robustness checks indicate the existence of inflation threshold in a range of 9-10%. In particular, the threshold level for food inflation is 10% and 8% for non-food inflation. In all cases, our results robustly confirm growth-detrimental effects of inflation after the threshold levels. After all, this study suggests the need for considering specific behaviors of food and non-food prices, and implementing appropriate fiscal and monetary policies to bring inflation down to a single-digit level.

China is in the climbing phase of the "Inverted U" environmental Kuznets curve, from excessive environmental consumption to the development stage of governance and protection, and green innovation. It is the most complex period of environmental quality. Environmental and policy regulation are very important. Select panel data of 29 provinces of China (excluding Hong Kong, Macau, Taiwan, Hainan and Tibet) from 2008 to 2017, construct a nonlinear two-threshold regression model, empirically analyse the impact of environmental tax and government innovation subsidies to green processes innovation, and attempt to explore whether the implementation of these two policies at the same time can make enterprises more inclined to green process innovation and whether there is an optimal space for policy implementation. It is proposed that the synergy effect of environmental tax and government innovation subsidy policies on enterprise green process innovation should be fully utilized, and the enterprise green process innovation environment and incentive mechanism should be improved to promote the green transformation and sustainable development of enterprises.

This article presents a method of segmenting images with gray levels that uses Onicescu's information energy calculated in the context of the neutrosophic theory. Starting from the information energy calculation for complete neutrosophic information, it is shown how to extend its calculation for incomplete and inconsistent neutrosophic information. The segmentation method is based on calculation of thresholds for separating the gray levels using the local maximum points of the Onicescu information energy.

The sustainability of irrigated agriculture depends on the quality of irrigation water used. The electrolyte concentration (EC) of irrigation water may lead to the accumulation of salts in the root zone layers and affect the physiological functions of the crop by osmotic and ion toxicity effects. Further, the cationic and anionic composition of the water may alter the exchangeable cation composition of the soil and as well as its pH. Because of the dominance of sodium salts in many sources of irrigation water, parameters related to sodium such as exchangeable sodium percentage (ESP) of soils and sodium adsorption ratio (SAR) of soil solutions have been commonly used to study the effects of sodium in irrigation water on soil structural stability. Quirk and Schofield concept of ‘threshold electrolyte concentration’ (TEC) has shown the importance of electrolytes in preventing the effects of sodium on soil structure. Based on this concept, several models have been proposed to relate ESP or SAR with EC to predict the possible impacts of irrigation water on soil structural stability. However, many research reports indicate that this relationship varies with soils and a given model is not suitable for all types of soils. Further, the effects of potassium and magnesium in the processes leading to clay dispersion are disregarded in these models. This essay analyses all the factors involved in the structural failure of soils with different cationic composition, identify the defects in these TEC models and re-defines TEC on the basis of new insights on dispersive and flocculating charges of soils. This review does not deal with EC effects on crops and also the role of contaminant ions not involved with soil structural stability.

Background: COVID-19 pneumonia caused by SARS-Cov-2 virus induces alveolar collapse and hypoxia that may become severe. The aim of the study is to analyze the effects of chest physiotherapy using a threshold valve in patients with acute respiratory failure due to COVID-19 pneumonia. Methods; Retrospective observational study, in hospitalized patients from March to May 2020. Breathing exercises were performed with a threshold valve of 10 cmH2O. Fraction of inspired oxygen, oxygen saturation, heart rate, respiratory rate and dyspnea were collected before and after the first session and at the end of the 5th day of chest physiotherapy treatment. Results: The final sample included 125 patients. Significant differences (p<0.01) were found in the pre-post intervention SpO2/FiO2 ratio (250±88.4 vs 275.6±97.5, p<0.001), reaching 354.4±110.2 after 5 days of therapy (p<0.001 with respect to baseline). Mean baseline respiratory, heart rate and level of dyspnea measure by the Borg scale did not change during the technique performance. In patient maneuvers with FiO2>0.4, the SaO2/FiO2 ratio increase was higher than in patients with milder severity (46.85 ± 77.69, p<0.01). Conclusions: Chest physiotherapy with a 10 cmH2O threshold valve is a safe and tolerated intervention with short-term improvement in oxygenation in patients with COVID-19 pneumonia.

Convective rainfall can cause dangerous flash floods within less than six hours. Thus, simple approaches are required for issuing quick warnings. The Flash Flood Guidance (FFG) approach pre-calculates rainfall levels (thresholds) potentially causing critical water levels for a specific catchment. Afterwards, only rainfall and soil moisture information is required to issue warn-ings. This study applied the principle of FFG to the Wernersbach Catchment (Germany) with excellent data coverage using the BROOK90 water budget model. The rainfall thresholds were determined for durations of 1 to 24 hours, by running BROOK90 in “inverse” mode, identifying rainfall values for each duration that led to exceedance of critical discharge (fixed value). After calibrating the model based on its runoff, we ran it in hourly mode with four precipitation types and various levels of initial soil moisture for the period 1996 – 2010. The rainfall threshold curves showed a very high probability of detection (POD) of 91% for the 40 extracted flash flood events in the study period, however, the false alarm rate (FAR) of 56% and the critical success index (CSI) of 42% should be improved in further studies. The approach proved potential as an early flood indicator for head-catchments with limited available information.

Background: Understanding SARS-CoV-2 dynamics and transmission is a serious issue. Its propagation needs to be modeled and controlled. The Alsace region in the East of France has been among the first French COVID-19 clusters in 2020. Methods: We confront evidence from three independent and retrospective sources: a population-based survey through internet, an analysis of the medical records from hospital emergency care services, and a review of medical biology laboratory data. We also check the role played in virus propagation by a large religious meeting that gathered over 2,000 participants from all over France mid-February in Mulhouse. Results: Our results suggest that SARS-CoV-2 was circulating several weeks before the first officially recognized case in Alsace on February 26^th 2020 and the sanitary alert on March 3^rd. The religious gathering seems to have played a role for secondary dissemination of the epidemic in France, but not in creating the local outbreak. Conclusions: Our results illustrate how the integration of data coming from multiple sources could help trigger an early alarm in the context of an emerging disease. Good information data systems, able to produce earlier alerts, could have avoided a general lockdown in France.

Sehezar area is located in southern Tonokabon in Mazandaran province, north of Iran, near the Tarom – Hashdtjin belt. The existence of granitoid masses in the region can be important in terms of the potential of mineralization. Geochemical anomaly separation from the background is one of the important steps in mineral exploration. In the past decades, geochemical anomalies have been identified by means of various methods. Some of these separation methods include: statistical analysis methods (like univariate, bivariate, multivariate statistics), spatial statistical methods and fractal and multi-fractal methods. To identify the anomalous area, 71 stream sediment samples were collected from the area and analyzed by the ICP-MS method, and then interpreted. Initially, data were normalized and afterwards, univariate analysis (threshold limit and screening (P.N) methods) was used, in which results of the probable and definite anomaly of the threshold method were confirmed by the P.N screening method. Finally, the maps of the anomal zones were drawn. Then, bivariate analysis (Pearson correlation coefficients) and multivariate analysis on normal data were performed on SPSS software, in which factor analysis and cluster analysis were used for multivariate analysis. As a result of using the factor analysis method, six factors were identified and factor maps were drawn by the Surfer software. Also, by using cluster analysis, the variables were divided into two groups. In order for a better separation of the geochemical anomaly from the background, in addition to the threshold method, the Concentration - Area fractal method was used. Here, the fractal geometry using full-logarithmic graphs of the Concentration - Area obtained is capable of separating the stairs of different sections (background, threshold, and anomaly) with respect to the angle coefficient of the Concentration - Area plot. Then, in conclusion, results of these methods were compared and investigated, and finally, the anomalies area maps of the Au, Ag, Cu, Fe, W elements were drawn by Concentration - Area fractal and threshold methods and anomalous zones were introduced.

Despite the continued growth of the sport, particularly among recreational athletes, very little is known about how triathletes prepare for an event. The aim of this study was to identify the training characteristics of recreational-level triathletes and assess how their preparation for a triathlon influences their health and fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after the event, ten (5 males, 5 females) recreational athletes completed a daily training log to provide information on every training session. In addition, participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Health Questionnaire weekly. Training loads were calculated using session-based rating of perceived exertion (sRPE) and training impulse (TRIMP). Every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. In the 6 weeks leading up to the event, training loads, total minutes trained, and time spent in each training zone did not differ significantly. Significant reductions in training duration (Z=2.39, p=0.017, ES = 0.90), training strain (Z=2.59, p=0.009, 0.98), and number of sessions (Z=2.49, p=0.012, ES = 0.94) were seen on week 6. Training intensity distribution favored a threshold approach with athletes spending 56% of their training time at zone 1, 40% at zone 2, and 4% at zone 3. No significant changes were seen in the DALDA or TDS questionnaires. The results show that while the training intensity distribution of recreational-level triathletes does not follow a polarized model, these athletes were able to maintain their health while preparing for an Olympic distance triathlon.

The identification of bloodstain is one of the most important approaches in obtaining evidence in criminalistics. A threshold method based on spectral co-efficient and interclass variance is proposed in this paper, it is a non-contact, non-destructive method for quickly identifying bloodstains. The spectra of bloodstains and other suspected substances were all extracted from their hyper-spectral image. Then calculate the correlation coefficients of these spectral and interclass variances, analyze the differences between substances. The best blood recognition threshold was determined as 0.9. After preprocessing for eliminating systematic errors, experiments with the threshold 0.9 are carried out to identify bloodstains on the calico and red T-shirt. The method can remarkably identify the bloodstain from other non-blood substances both quickly and efficiently. The blood extraction rate can reach to 93.35% and 89.19%, respectively. It is an important step toward the implementation of bloodstain non-contact and non-destructive identification in forensic casework.

Electrically conductive polymer composites are in high demand for modern technologies, however, the intrinsic brittleness of conducting conjugated polymers and the moderate electrical conductivity of engineering polymer/carbon composites have highly constrained their applications. In this work, super high electrical conductive polymer composites were produced by a novel hot embossing design. The polydimethylsiloxane (PDMS) composites containing short carbon fiber (SCF) exhibited an electrical percolation threshold at 0.45 wt%, and reached a saturated electrical conductivity of 49 S/m at 8 wt% of SCF. When reduced the sample thickness from 1.0 mm to 0.1 mm by the hot embossing process, a compression-induced percolation threshold occurred at 0.3 wt%, while the electrical conductivity was further enhanced to 378 S/m at 8 wt% SCF. Furthermore, the additional of a second nanofiller of 1 wt%, such as carbon nanotube or conducting carbon black further increased the electrical conductivity of the PDMS/SCF (8 wt%) composites to 909 S/m and 657 S/m, respectively. The synergy of the densified conducting filler network by the mechanical compression and the hierarchical micro-/nanoscale filler approach has realize super high electrical conductive yet mechanical flexible polymer composites for modern flexible electronics applications.

Imperceptible vibratory noise stimulation has shown to be an effective means of improving stability for both whole body postural control and simple motor control tasks. While the physiological mechanism affording this improvement is uncertain, it is suspected that sensory noise stimulation may elicit a stochastic resonance-like effect within the somatosensory system. A stochastic resonance effect describes the phenomenon in which noise added to a non-linear system improves signal detection rather than degrading it. One hallmark of stochastic resonance is the existence of an optimal noise level which elicits the best system performance. There is disagreement in the literature regarding the presence of an optimal stimulation level for motor stability in humans. The goals of this study were to: 1) determine optimal stimulation level as a function of an individual’s sub-sensory threshold level, and 2) to determine whether performance of a force stability task was significantly better when subjects received stimulation at this identified optimal level compared to other sub-sensory threshold stimulation levels. Eighteen (18) participants completed an isometric finger flexion task with visual feedback while receiving noise stimulation scaled to varying percentages of their individual sub-sensory threshold level. Performance for this force stabilization task was quantified as the root-mean-square (RMS) error between the target force and the actual generated force values. Despite controlling all other signal properties and varying only amplitude, optimal noise stimulation values still varied widely across participants (10-100% sub-sensory threshold level). Statistical modeling revealed a significant improvement in task performance with optimal noise stimulation compared to other sub-sensory stimulation levels (p ≤ 0.019) with estimated marginal mean differences in force errors ranging from 0.13 to 0.23 N. Moderate significant Spearman correlations (r_s = 0.49 and r_s = 0.56, respectively) were found between finger flexion maximal voluntary contraction (MVC) and sub-sensory threshold level and MVC and optimal stimulation level. A strong, significant Spearman correlation (r_s = 0.65) was observed between sub-sensory threshold level and optimal stimulation level. Although these correlations do not provide a means to predict optimal stimulation level as a function of these other measures, optimal stimulation level appears to increase with sub-sensory threshold and MVC.

Although the majority of mobile phone (MP) users do not attribute adverse effects on health or well-being to MP-emitted radiofrequency (RF) electromagnetic fields (EMFs), the exponential increase in the number of RF devices necessitates continuing research aimed at the objective investigation of such concerns. In this work, we investigate the effects of acute exposure from Long Term Evolution (LTE) MP EMFs on thermal pain threshold in healthy young adults. We use a protocol that was validated in a previous study in a capsaicin-induced hyperalgesia model, and was also successfully used to show that exposure from an RF source mimicking a Universal Mobile Telecommunications System (UMTS) MP led to mildly stronger desensitization to repeated noxious thermal stimulation relative to the sham condition. Using the same experimental design, we did not find any effects of LTE exposure on thermal pain threshold. The present results are in accordance with previous evidence suggesting that effects are likely to be placebo/nocebo effects and are unrelated to the brief acute LTE EMF exposure itself. The fact that this is dissimilar to our previous results on UMTS exposure implies that RF modulations might differentially affect pain perception, and points to the necessity of further research in the topic.

This paper presents the results of an experimental investigation about target detecting with passive sonar in Persian Gulf. Detecting propagated sounds in the water is one of the basic challenges of the researchers in sonar field. This challenge will be complex in shallow water (like Persian Gulf) and noise less vessels. Generally, in passive sonar the targets are detected by sonar equation (with constant threshold) which increase the detection error in shallow water. Purpose of this study is proposed a new method for detecting targets in passive sonars using adaptive threshold. In this method, target signal (sound) is processed in time and frequency domain. For classifying, Bayesian classification is used and prior distribution is estimated by Maximum Likelihood algorithm. Finally, target was detected by combining the detection points in both domains using LMS adaptive filter. Results of this paper has showed that proposed method has improved true detection rate about 27% compare other the best detection method.

Febrile seizures in early childhood can lead to developmental disorders in the CNS. However, the specific mechanisms behind the impact of febrile seizures on the developing brain are not well-understood. To address this gap in knowledge, we employed a hyperthermic model of febrile seizures in 10-day-old rats and tracked their development over two months. Our objective was to determine the degree to which the properties of the hippocampal glutamatergic system are modified. We analyzed whether pyramidal glutamatergic neurons in the hippocampus die after febrile seizures. Our findings indicate that there is a reduction in the number of neurons in various regions of the hippocampus in the first two days after seizures. The CA1 field showed the greatest susceptibility, and the reduction in the number of neurons in post-FS rats in this area appeared to be long-lasting. Electrophysiological studies indicate that febrile seizures cause a reduction in glutamatergic transmission, leading to decreased local field potential am-plitude. This impairment could be attributable to diminished glutamate release probability as evidenced by decreases in frequency of miniature excitatory postsynaptic currents and increases in pair-pulse ratio of synaptic responses. We also found higher threshold current causing hindlimb extension in the maximal electroshock seizure threshold test of rats 2 months after febrile seizures compared to control animals. Our research suggests that febrile seizures can impair glutamatergic transmission, which may protect against future seizures.

In order to better realize rural revitalization, this paper analyzes the spatial and temporal char-acteristics and influencing factors of agricultural surface source pollution in the Yangtze River Economic Belt from the three perspectives of government, enterprise and agriculture by using the spatial Durbin model and the dynamic GMM method in the period of 2006-2021, and further re-searches the threshold characteristics of the distortion of the factor market on the agricultural surface source pollution under the different strengths of environmental regulation. The results show that there is a positive spatial correlation between agricultural surface pollution in the Yangtze River Economic Belt, and government environmental regulation, input factor market distortion and labor force transfer all have a significant impact on agricultural surface pollution. Among them, factor market distortion has a significant spatial spillover effect on agricultural surface pollution in the Yangtze River Economic Zone, and has a significant single-threshold ef-fect on environmental regulation. Accordingly, the government should strengthen environmental regulation, continuously improve the agricultural factor market mechanism, and pay attention to the construction of talents to provide support for rural revitalization.

Lagoons are becoming sporadically utilised albeit they are equipped with high potential for the outsourcing of environmental and industrial benefits. It leads to the endangered pollution of lagoon water aquatic system. The prime reason is the lack of knowledge among stakeholders and researchers regarding the influential parameters in establishing the lagoon water quality. The optimal quality for lagoon water is critical for the longevity of aquatic ecosystem. This study focuses on using bibliographic references to find the most influential factors determining the water quality in lagoons for deriving a comprehensive long-term water quality monitoring plan to ensure the sustainability of the lagoon water ecosystem. The lagoon water quality was classified in this study into biological, physical, and chemical parameters and studied for their importance upon enhancing the water quality. Experiments were conducted on selected parameters using the water samples from the selected Sri Lankan lagoons with available facilities to observe the water quality. The overall findings on physiochemical and biological characteristics using the experiments temperature, turbidity, pH, salinity, DO, BOD, COD, phosphates, nitrates, ammonia content and faecal coliforms in water specimens suggest that the selected Sri Lankan lagoons are heavily polluted due to their distinctive variations from the allowable threshold limits specified in the literature sources. To increase such increased risks associated with lagoon water systems, a long-term monitoring strategy is recommended to be incorporated at lagoon waters in order to assure their sustainability.

Patients with degenerative diseases refer to feeling more pain during the night. However, it is unknown whether spinal nociception can be circadian and how is it controlled. We investigated whether the paw withdrawal threshold (PWT) could exhibit physiological circadian behavior as well as the contribution of the dopaminergic A11 nucleus and the spinal dopamine (DA) receptors (DRs) on the circadian PWT and the spinal clock gene transcription. Results revealed that control rats present a circadian PWT. Injecting 6-hydroxidopamine (6-OHDA) into the dopaminergic A11 nucleus reduced DA tissue content in the lumbar spinal cord, abolished the circadian PWT, induced allodynia, and reduced Period 1 and 2 (Per1 and 2), retinoid-related orphan receptor α (Rorα), Cryptochrome 1 (Cry1), and brain and muscle aryl-hydrocarbon receptor nuclear translocator-like protein (Bmal) mRNA. Likewise, administration of D1-like and D2-like DR antagonists blunted circadian PWT, producing allodynia, and altered the clock genes mRNA. In contrast, administration of D1-like or D2-like DR agonists blocked 6-OHDA-induced allodynia. This study shows that the spinal cord has physiological circadian PWT, which is modulated by the descending dopaminergic A11 through differential activation of the spinal DRs. Also, A11 nuclei and spinal DRs can regulate the clock gene transcription, which can likely modulate the circadian PWT.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

Water distribution networks are often susceptible to pipeline leaks caused by mechanical damages, natural hazards, corrosion, and other factors. This paper focuses on the detection of leaks in water distribution networks (WDN) using a data-driven approach based on machine learning. A hybrid Autoencoder neural network (AE) is developed, which utilizes unsupervised learning to address the issue of unbalanced data (as anomalies are rare events). The AE consists of a 3DCNN encoder, a ConvLSTM decoder, and a ConvLSTM future predictor, making the anomaly detection robust. Additionally, spatial, and temporal attention mechanisms are employed to enhance leak localization. The AE first learns the expected behavior and subsequently detects leaks by identifying deviations from this expected behavior. To evaluate the performance of the proposed method, the Water Network Tool for Resilience (WNTR) Simulator is utilized to generate water pressure and flow rate data in a water supply network. Various conditions such as fluctuating water demands, data noise, and the presence of leaks are considered using the pressure-driven demand (PDD) method. Datasets with and without pipe leaks are obtained, where the AE is trained using the dataset without leaks and tested using the dataset with simulated pipe leaks. The results, based on a benchmark WDN and a confusion matrix analysis, demonstrate that the proposed method successfully identifies leaks in 96% of cases and a false positive rate of 4% compared to a random forest model baseline based on supervised learning with a false positive rate of 15% due to unbalanced data. Furthermore, a real case study demonstrates the applicability of the developed model for leak detection in operational conditions of water supply networks using inline sensor data.

Variations in threshold voltage (VTH) and charge distributions in noncircular cells of three-dimensional (3D) NAND flash memory are investigated. The electric field difference in the circular and spike regions causes nonuniform trapped electron density in the charge trap layer (CTL) and influences the VTH variation. Such less-trapped electron (LT) regions in CTL between the circular and spike regions exhibit a lower electric field during the program, resulting in a higher current flow through that region. For the two-spike cells, the charge distribution and VTH variation are analyzed at different heights (HSpike) and angles between spikes. These irregular cells decrease VTH as the HSpike increases.

Understanding how industrial agglomeration affects agricultural green production efficiency is essential for green agricultural development. This study uses the super-efficient EBM-GML to measure and analyze the spatial and temporal evolution characteristics and core sources of dynamics of agricultural green production efficiency in China by using panel data from 30 Chinese provinces from 2006 to 2020. It also empirically investigates the relationships between industrial agglomeration, land transfer, and agricultural production efficiency. By using fixed, intermediary, and threshold effects models, the internal links between the industrial agglomeration, land transfer, and agricultural green production efficiency are examined. The findings indicate that the green production efficiency of Chinese agriculture exhibits the regional characteristics of being “high in the west and low in the east, high in the south and low in the north” in terms of space; in terms of time series, the overall trend is that of growing, with an average annual growth rate of 11.45%, and the growth primarily depends on the “single-track drive” of green technological progress. By promoting land transfer, industrial agglomeration can increase the agricultural green production efficiency and decomposition index. Land transfer has a double-threshold effect on the influence of industrial agglomeration on agricultural green production efficiency. As a result, this study suggests adhering to the idea of synergistic development, promoting agricultural green development, strengthening the development of industrial agglomerations, promoting the quality and efficiency of industry, improving land-transfer mechanisms, and placing a focus on resource efficiency improvements, as well as other policy recommendations.

Channel estimation is an important module to enhance the performance of orthogonal frequency division multiplexing (OFDM) systems. However, the presence of a large amount of noise in multipath fading time-varying channels significantly affects the channel estimation accuracy and thus the recovery quality of the received signals. Therefore, this paper proposes a double-threshold (DT) channel estimation method based on adaptive frame statistics (AFS). The method first adaptively determines the number of statistical frames based on the temporal correlation of the received signals, and preliminarily detects the channel structure by analyzing the distribution characteristics of multipath sampling points and noise sampling points during adjacent frames. Subsequently, a multi-frame averaging technique is used to expand the distinction between multipath and noise sampling points. Finally, the DT is designed to better recover the channel based on the preliminary detection results. Simulation results show that the proposed adaptive frame statistics-double-threshold (AFS-DT) channel estimation method is effective and has better performance compared with many existing channel estimation methods.

The aim of this work is a comprehensive study of the effect of variable atomic composition and structural-phase state of (CoFeZr)x(MgF2)100-x nanocomposites (NCs) on their nonlinear electronic and magnetic/magneto-optical properties. Micrometer-thick nanocomposites layers on the glass substrates were obtained by ion-beam sputtering of a composite target in the argon atmosphere in a wide range of compositions x=9-51at.% The value of the resistive percolation threshold xper=34 at.%, determined from the concentration dependences of the electrical resistance of NCs, coincides with the beginning of nucleation of metallic nanocrystals CoFeZr in MgF2 dielectric matrix. The absolute value of maximum magnetoresistance of NCs is 2.4 % in a magnetic field of 5.5 kOe at x=25 at.%, up to the percolation threshold. Two maxima appear in the concentration dependences of magneto-optical transversal Kerr effect, one of which at x = 34 at.% corresponds to the formation of CoFeZr alloy nanocrystals of a hexagonal structure, and the second one at x=45 at.% corresponds to the phase transition of nanocrystals from a hexagonal to a cubic body-centered structure. The magnetic percolation threshold in (CoFeZr)x(MgF2)100-x system at xfm=34 at.% with the appearance of a hysteresis loop and a coercive force of Hc≈ 8 Oe, coincides with the resistive percolation threshold xper=34 at.%. Concentration dependence of the coercive force showed that at low contents of metallic alloy x<30 at.% NCs are superparamagnetic (Hc=0). With an increase of the alloy content, in the region of magnetic and resistive percolation thresholds NCs exhibit a magnetically soft ferromagnetic character and do not change it far beyond the percolation threshold with the maximum value of the coercive force Hc< 30 Oe. Decrease in magnetic order and soft ferromagnetic are influenced by the diamagnetic phase FeF2 that we discovered at the interface of magnetic nanocrystals CoFeZr with a dielectric matrix MgF2 by the Mössbauer spectroscopy.

This paper presents a study on the influence of the frequency variation of a nonlinear1 control allocation technique execution, developed by the author [1], named by Fast Control2 Allocation (FCA) for the Quadrotor Tilt-Rotor (QTR) aircraft. Then, through Software In The3 Loop (SITL) simulation, the proposed work considers the use of Gazebo, QGroundControl, and4 Matlab applications, where different frequencies of the FCA can be implemented separated in5 Matlab, always analyzing the QTR stability conditions from the virtual environment performed in6 Gazebo. TheresultsshowedthattheFCAneedsatleast200HzoffrequencyfortheQTRsafeflight7 conditions, i. e., 2 times smaller than the main control loop frequency, 400 Hz. Lower frequencies8 than this one would case instability or crashes during the QTR Operation.

The design flood concept (DF) provides for an essential tool in designing the hydraulic works, in defining the reservoir operation programs and for a reliable flood hazard identification. Under a simplified approach, the maximum discharge and the floods volume are statistically processed to reasonably define the DF. Yet, the integral hydrograph provides additional key temporal and quantitative details of important significance for flood management and particularly for the res-ervoirs operation and associated risks of failures. The procedure presented in this paper (as applied on a set of compatibly shaped hydrographs) involves the following key stages: (i) normalize the floods, (ii) define similar flood shape classes and (iii) evaluate the average dimensionless flood (ADF) for each class. The ADFs are finally transformed into a set of (DF)s. Many statistical distributions approximate acceptably the frequent values of the maximum discharges or the flood volumes, yet displaying a significant spread for medium or rare probabilities of exceedance (PE). This scattering, which can be explained by the epistemic uncertainty, defines an area of uncertainty both for measured and extrapolated values. In considering upper and lower values of the uncertainty in-tervals as limits for maximum discharges and flood volumes, then by combining them compatibly, a set of DFs - as completely defined hydrographs, with different shapes - results for each PE. The herein proposed procedure defines both one peak DF and multi-peaks DF. Subsequently, such DFs do assist water managers in examining and establishing tailored approaches for a variety of input hydrographs. Among the DFs that would correspond to a same PE, the most compact floods arise a special interest, for they are basic in defining the set of safe operation rules for hydraulic structures.

Due to the continuous trade friction between China and the United States, for domestic enterprises in China, the cost of importing foreign technologies is increasing. Thus, the independent research and development (R&D) becomes particularly important for the realization of green technology innovation (GTI). This paper establishes a non-linear mediating effect model based on the data of various regions in China from 2012 to 2018. The main results are shown in the following. Firstly, there is an inverted U-shaped relationship between the intensity of intellectual property protection (IPP) and the level of GTI. Furthermore, the independent R&D investment has a masking effect between them. Secondly, by taking the independent R&D investment as a threshold variable, we prove our findings. Considering that the intensity of IPP is at a high level in most regions of China, the above statements mean that the enterprises need to continuously increase their investment in R&D, in order to further improve the regional ability in GTI. Meanwhile, local governments should also stimulate enterprises' willingness to expand their scale in R&D by issuing incentive policies, such as R&D tax incentives and government subsidies.

We have analysed the death and recovery rate of Covid-19 disease progression. From the analysis, we have argued that the pandemic is over in certain countries (labelled as group-A) and for other countries (labelled as group-B) the disease appears to remain as endemic. Taking into account the serological survey (sero-survey) test results obtained by certain groups and comparing it with herd immunity threshold value one can infer that the low number of infection for group-B is either due to acquired immunity by some previous infection by other coronavirus or due to innate immunity towards this infection. This effect is stronger for group-B to slow the progress of the disease to such an extent resulting in flattening of the disease progression curve compared to group-A.

This paper compares the finite sample performance of three non-parametric threshold estimators via Monte Carlo method. Our results show that the finite sample performance of the three estimators is not robust to the relative position of the threshold level along the distribution of threshold variable, especially when a structural change occurs at the tail part of the distribution.

When we are asleep we lose the ability to promptly respond to external stimuli and yet we spend many hours every day in this inherently risky behavioral state. This simple fact strongly suggests that sleep must serve essential functions that rely on the brain going offline, on a daily basis, and for long periods of time. If these functions did not require partial sensory disconnection, it would be difficult to explain why they are not performed during waking. Paradoxically, despite its central role in defining sleep and what sleep does, sensory disconnection during sleep remains a mystery. We have a limited understanding of how it is implemented along the sensory pathways, we do not know whether the same mechanisms apply to all sensory modalities, nor do we know to which extent these mechanisms are shared between non-rapid eye movement (NREM) sleep and REM sleep. The main goal of this contribution is to review some knowns and unknowns about sensory disconnection during sleep as a first step to fill this gap.

Permeability is an important transport property of porous materials, and its accurate evaluation is relevant in studying applied tasks such as CO2 injection into reservoirs and investigating groundwater quality issues. This study examines the dependence of permeability on total and connected porosity, hydraulic tortuosity, specific surface area, and mean pore radius based on the data of 408 cubic sub-volumes extracted from heterogeneous and naturally fractured cylindrical carbonate samples before and after injection of HCl solutions into them. These parameters were computed using pore-scale modeling of fluid flow. It has been shown that permeability correlates well with porosity and mean pore radius with correlation coefficients of R2≈0.65-0.79 for heterogeneous samples. It was found that the presence of natural fractures significantly influenced the relationship between permeability and other parameters. The relationship between permeability k, tortuosity τ, and specific surface area S is described by power laws k~τ-α and k~S-β, with coefficients α and β substantially exceeding those in the Kozeny-Carman equation. It was also found that there is a parabolic relationship between connected and total porosities both before and after rock dissolution with R2≈0.96-0.99. This allowed for estimation of percolation threshold porosity that are in good agreement with the literature data.

In swarm-robotics foraging, the purpose of task allocation is to adjust the number of active foraging robots dynamically based on the task demands and changing environment. It is a difficult challenge to generate self-organized foraging behavior in which each robot can adapt to environmental changes. To complete the foraging task efficiently, this paper presents a novel self-organized task allocation strategy known as the dynamic response threshold model (DRTM). To adjust the behavior of the active foraging robots, the proposed DRTM newly introduces the traffic flow density, which can be used to evaluate the robot density. First, the traffic flow density and the amount of obstacle avoidance are used to adjust the threshold which determines the tendency of a robot to respond to a stimulus in the environment. Then, each individual robot uses the threshold and external stimulus to calculate the foraging probability that determines whether or not to go foraging. Simulation and physical experiments are carried out to evaluate the performance of the proposed method. The experimental results show that the DRTM is superior to and more efficient than the adaptive response threshold model (ARTM) in swarm foraging.

Drylands are arid and semiarid ecosystems, where the lack of rains imposes harsh conditions for the survival of organisms. These ecosystems are also susceptible to degradation and desertification, and their conservation depends on the understanding of the ecological functioning of vegetation and soil. In drylands, the vegetation is spatially structured as a mosaic of patches (vegetation) and interpatches (bare soil), a consequence of plant-plant interactions (facilitation and competition). Empirical data and modeling approaches reinforce the role of ecological facilitation for the maintenance of all organisms in drylands. However, the actual range of facilitation is still poorly known. Here, we explored data of meso- and micro-arthropods found in soil as bioindicators to infer the range of facilitation provided by plants to soil. We regarded data of abundances and species densities (independent samples) collected in random patches and bare soil places as dependent variables. Data of patch size and distances between bare soil and patches were arranged in a single shuffle, producing a 1-d coordinate system centered at the border of the patch. Discrete portions of this system are taken to calculate averages and variances of abundance and species density, and we investigated how soil communities variate across the patch border. We employ techniques of signal analysis to reduce the data noise and obtain a smooth and continuous behavior, which allowed us to fit a logistic function. Our findings indicate that soil communities suddenly change from simple patterns to numerous and diverse communities in bare soil regions, meaning that the influence of vegetation on soil goes beyond the patch border. We interpreted the variations in fauna as a consequence of the positive influence provided by plants (or its lack) on surrounding bare soil. We observe a fast decaying of fauna quantities at 0.35 m outside the patch border, a threshold that reveals the mean range of facilitation provided by plants. However, the changes in soil communities outside the patches seem not necessarily related to the efficiency of soil processes mediated by arthropods, which seem to be more active inside large patches. Concluding, we found a minimum patch-size (radius ~ 0.5 m) able to maintain high diverse communities in soil, and an average distance of vegetation influence along the patch border (halo between 0.35 and 0.50 m). This information can be interpreted in terms of facilitation provided by plants to soil conditions, which seems to differ from the quantitative functionality of soil processes. Our findings contribute to the general understanding of the ecological functioning of drylands, as well as to better plan conservation actions.

Energy-efficient microprocessors are essential for a wide range of applications. While near-threshold computing is a promising technique to improve energy efficiency, optimal supply demands from logic core and on-chip memory are conflicting. In this paper, we perform static reliability analysis of 6T SRAM and discover the variance among different sizing configuration and asymmetric minimum voltage requirements between read and write operations. We leverage this asymmetric property in near-threshold processors equipped with voltage boosting capability by proposing an opportunistic dual-supply switching scheme with a write aggregation buffer. Our results show that proposed technique improves energy efficiency by more than 21.45% with approximate 10.19% performance speed-up.

Effective discharge, which represents the flow, or range of flows, that transport the most sediment over long term, was determined based on the mean daily flow discharge and mean daily suspended sediment discharge recorded between 1994 and 2014 at four gauging stations along the Trotuș River. This study proposes an efficient method for the estimation of effective discharge based on observed values of the suspended sediment load. By employing this method the suspended sediment load is no longer either under- or overestimated as in the cases when the assessment is based on sediment rating curves. The assessment on effective discharge was performed at two distinct levels: for the entire data series during the investigated time spans and, subsequently, for flows less than the bankfull discharge. The effectiveness curves of the suspended sediment transport characteristics revealed highly multimodal characteristics with many peaks, indicating ample ranges for the effective discharges. The main effective discharge corresponded to large flood events, which are typical for the upper end of the discharge range, whereas the secondary effective discharges corresponded to sub-bankfull flows, which are more frequent. The changes that occurred in the channel bed are reflected by the temporal variations in the effective discharge.

Many studies, which try to analyze conditions for debris flow development, ignore the type of initiation. Therefore this paper deals with the following questions: What type of hydro-mechanical triggering mechanisms for debris flows can we distinguish in upstream channels of debris flow prone gullies? Which are the main parameters controlling the type and temporal sequence of these triggering processes and what is their influence on the meteorological thresholds for debris flow initiation? A series of laboratory experiments were carried out in a flume, 8 m long and with a width of 0.3 m. to detect the conditions for different types of triggering mechanisms. The flume experiments show a sequence of hydrological processes triggering debris flows, namely erosion and transport by intensive overland flow and by infiltrating water causing failure of channel bed material. On the basis of these experiments an integrated hydro-mechanical model was developed, which describes Hortonian and Saturation overland flow, maximum sediment transport, through flow and failure of bed material. The model was calibrated and validated using process indicator values measured during the experiments in the flume. Virtual model simulations, carried out in a schematic hypothetical source area of a catchment show that slope angle and hydraulic conductivity of the bed material determine the type and sequence of these triggering processes. It was also clearly demonstrated that the type of hydrological triggering process and the influencing geometrical and hydro-mechanical parameters may have a great influence on rainfall intensity-duration threshold curves for the start of debris flows.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

This paper presents a methodology for indirectly estimating the scale of seabird bycatch using existing data, eliminating the need for regular monitoring. The study focuses on five species of ducks that winter in the Polish waters of the Baltic Sea and are highly susceptible to bycatch: Long-tailed Duck, Velvet Scoter, Common Scoter, Greater Scaup, and Tufted Duck. The evaluation units used are divided into the Bornholm and Gotland Groups within the Polish Exclusive Economic Zone (PEEZ). The analysis acknowledges the lack of data for certain areas known to have high concentrations of diving birds and fishing activity. The population sizes of waterbirds were assessed using ship-based surveys and a distance sampling approach. Fishing effort data from the winter seasons between 2015/2016 and 2019/2020 were analyzed. Bycatch rates were estimated based on surveys conducted in previous seasons, and threshold values for bycatch were established using the concept of "small numbers" defined in EU directives. The results show that within the Gotland subdivision of the PEEZ, the estimated average abundance of all diving waterbirds was 207,114 individuals, with an average bycatch of 7,921 birds (3.8% of the total). The Velvet Scoter was the most abundant species, followed by the Long-tailed Duck. Benthivorous ducks constituted the majority of the bird population in the area. In the Bornholm subdivision, the estimated average abundance of diving waterbirds was 600,845 individuals, with an average bycatch of 5,056 birds (0.8% of the total). The Long-tailed Duck was the most numerous species, followed by the Velvet Scoter. Benthivorous ducks also dominated in this area. The findings highlight the need for effective management and conservation measures to address the high mortality of seabirds due to bycatch. The methodology presented in this study offers a valuable approach for estimating bycatch scale and can support efforts to minimize the impact on seabird populations in the Baltic Sea.

The theory of one-photon ionization and two-photon above-threshold ionization is formulated for applications to heavy atoms in attosecond science using the Dirac-Fock formalism. A direct comparison of the Wigner-Smith-Eisenbud delays for photoionization is made with delays from the Reconstruction of Attosecond Beating By Interference of Two-photon Transitions (RABBIT) method. Photoionization by an attosecond pulse train, consisting of monochromatic fields in the extreme ultraviolet range, is computed with many-body effects at the level of the Relativistic Random Phase Approximation (RRPA). Subsequent absorption and emission processes of infrared laser photons in RABBIT are evaluated using static ionic potentials as well as asymptotic properties of relativistic Coulomb functions. As expected, light elements, such as Argon, show negligible relativistic effects, while heavier elements, such a Krypton and Xenon, exhibit delays that depend on the fine-structure of the ionic target. The relativistic effects are notable close to ionization thresholds and Cooper minima with differences in fine-structure delays predicted to be as large as tens of attoseconds. The separability of relativistic RABBIT delays into a Wigner-Smith-Eisenbud delay and a universal continuum--continuum delay is studied with reasonable separability found for photoelectrons emitted along the laser polarization axis in agreement with prior non-relativistic results.

Drought events are predicted to become more prevalent in the future. Evaluating the performance of herbicide-resistant and susceptible weed ecotypes to progressive drought can provide insights into whether resistance trait(s) increased or reduced the fitness of a resistant population. Two experiments were conducted in the greenhouse between January and May 2021 to evaluate drought tolerance differences between Palmer amaranth accessions resistant to S-metolachlor or glyphosate and their susceptible counterparts. The accessions used were: S-metolachlor-resistant (17TUN-A), a susceptible standard (09CRW-A), and glyphosate-resistant (22 to 165 EPSPS copies) and glyphosate-susceptible (3 to 10 EPSPS copies) plants from accession 16CRW-D. Daily transpiration of each plant was measured. The daily transpiration rate was converted to normalized transpiration ratio (NTR) using a double-normalization procedure. The daily soil water content was expressed as a fraction of transpirable soil water (FTSW). The threshold FTSW (FTSWcr), after which NTR decreases linearly, was estimated using a two-segment linear regression analysis. The data showed differences between S-metolachlor- resistant and -susceptible accessions (P ≤ 0.05). The FTSW remaining in the soil at the breakpoint for the S-metolachlor-susceptible accession (09CRW-A) was 0.17±0.007. The FTSW remaining in the soil at the breakpoint for the S-metolachlor-resistant accession (17TUN-A) was 0.23±0.004. Although the mechanism endowing resistance to S-metolachlor might have contributed to increased drought tolerance, follow-up experiments are needed to verify this finding. Increased EPSPS copy number did not improve drought tolerance of Palmer amaranth.

Fog computing is a potential solution to overcome the shortcomings of the cloud computing processing of IoT tasks. These drawbacks can be high latency, location awareness and security, and it is attributed to the distance between IoT devices and servers, network congestion and other variables. Although fog computing has evolved as a solution to these challenges, it is known for having limited resources that need to be consciously utilised, or any of its ad-vantages would be lost. Computational offloading and resource management are critical concerns to be considered to get maximum benefit of the available resource at fog computing systems and benefit from its advantages. Computational offloading and resource management are important issues to be considered to get maximum benefit of the available resource at fog computing systems and benefit from its advantages. In this article, in vehicular traffic applications, we introduce a dynamic online offloading scheme that involves the execution of delay-sensitive ac-tivities. This paper proposes an architecture of a fog node that enables a fog node to adjust its offloading threshold dynamically (i.e., the criteria by which a fog node decides whether tasks should be offloaded rather than executed locally) using two algorithms: dynamic task scheduling (DTS) and dynamic energy control (DEC). These algorithms seek to solve an optimisation problem aimed at minimising overall delay, improving throughput, and minimising energy consumption at the fog layer, while maximising the use of resource-constrained fog nodes. Compared with other benchmarks, our approach can reduce the delay by up to 95.38% and reduce energy consumption by up to 67.71% in fog nodes. Additionally, this approach enhances throughput by 71.08%.

Current pharmacological treatments of Fibromyalgia (FM) are merely symptom palliative, as clinical trials have so far failed to provide overall benefits without associated harms. Polypharmacy often leads to patient´s health deterioration and chronic drug use to an eventual lack of patient´s response. Emerging evidence support that physiotherapy treatments based on mechanical triggers improve FM symptoms and therefore could be used for therapeutic purposes by themselves, or in combination with current pharmacological treatments, as part of integrative medicine programs. However, a paucity of studies rigorously and systematically evaluating this possibility exists. This study uses scores from validated standardized questionnaires, algometer pressure point threshold (PPT) readings and responses from a custom self-developed questionnaire to determine the impact of a pressure-controlled manual protocol on FM hyperalgesia/allodynia, fatigue and patient´s quality of life. The results show that patient´s baseline sensitivity to pain inversely correlates with treatment response in FM. Moreover, patients presenting comorbid ME/CFS do not seem to respond to the applied therapy as those presenting FM only. Thus, pre-treatment PPTs and ME/CFS comorbidity may serve as indicators to predict patient´s response to physiotherapy programs based on mechanical triggers, as the one evaluated here. These unexpected findings grant further explorations including the study of gene expression profiles associating to patient´s treatment response in the blood collection of samples generated by this study.

Single-molecule fluorescence detection (SMFD) experiments are useful in distinguishing sub-populations of molecular species when measuring heterogeneous samples. One experimental platform for SMFD is based on a confocal microscope, where molecules randomly traverse an effective detection volume. The non-uniformity of the excitation profile and the random nature of Brownian motion, produce fluctuating fluorescence signals. For these signals to be distinguished from the background, burst analysis is frequently used. Yet, the relation between the results of burst analyses and the underlying information of the diffusing molecules is still obscure and requires systematic assessment. In this work we performed three-dimensional Brownian motion simulations of SMFD, and tested the positions at which molecules emitted photons that passed the burst analysis criteria for different values of burst analysis parameters. The results of this work verify which of the burst analysis parameters and experimental conditions influence both the position of molecules in space when fluorescence is detected and taken into account, and whether these bursts of photons arise purely from single molecules, or not entirely. Finally, we show, as an example, the effect of bursts that are not purely from a single molecule on the accuracy in single-molecule Förster resonance energy transfer measurements.

We asked whether the level of peripheral fatigue would differ when three consecutive exercise trials were completed to task failure, and whether there would be delayed recovery in maximal voluntary contraction (MVC) force, neuromuscular activation and peripheral fatigue following task failure. Ten trained sport students performed three consecutive knee extension isometric trials (T1, T2, T3) to task failure without breaks between trials. T1 and T2 consisted of repeated 5-s contractions followed by 5-s rest. In T1, contractions were performed at a target force at 60% pre-exercise MVC. In T2, all contractions were MVCs, and task failure occurred at 50% MVC. T3 was a sustained MVC performed until force fell below 15% MVC. Evoked force responses to supramaximal electrical femoral nerve stimulation were recorded to assess peripheral fatigue. Electromyography signals were normalized to M-wave amplitude to assess neuromuscular activation. Lower levels of evoked peak forces were observed at T3 compared to T2 and T1. Within 5 s of task failure in T3, MVC force and neuromuscular activation recovered substantially without any recovery in evoked peak force. Neuromuscular activation 5-10 s after T3 was unchanged from pre-exercise values, but evoked peak forces were substantially reduced. These results challenge the existence of a critical peripheral fatigue threshold that reduces neuromuscular activation. Since neuromuscular activation changed independently of any change in evoked peak force, immediate recovery in force production after exercise is due to increased central recruitment and not to peripheral mechanisms.

Supervised land-use/land-cover (LULC) classifications are typically conducted using class assignment rules derived from a set of multiclass training samples. Consequently, classification accuracy varies with the training data set and is thus associated with uncertainty. In this study, we propose a bootstrap resampling and reclassification approach that can be applied for assessing not only the uncertainty in classification results of the bootstrap-training data sets, but also the classification uncertainty of individual pixels in the study area. Two measures of pixel-specific classification uncertainty, namely the maximum class probability and Shannon entropy, were derived from the class probability vector of individual pixels and used for the identification of unclassified pixels. Unclassified pixels that are identified using the traditional chi-square threshold technique represent outliers of individual LULC classes, but they are not necessarily associated with higher classification uncertainty. By contrast, unclassified pixels identified using the equal-likelihood technique are associated with higher classification uncertainty and they mostly occur on or near the borders of different land-cover.

Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

The deformation monitoring information of concrete dams contains some high-frequency com-ponents, and the high-frequency components are strongly nonlinear, which reduces the accuracy of dam deformation prediction. In order to solve such problems, this paper proposes a concrete dam deformation monitoring model based on empirical mode decomposition (EMD) combined with wavelet threshold noise reduction and sparrow search algorithm (SSA) optimization of long short-term memory network (LSTM). The model uses EMD combined with wavelet threshold to decompose and denoise the measured deformation data. On this basis, the LSTM model based on SSA optimization is used to mine the nonlinear function relationship between the reconstructed monitoring data and various influencing factors. The example analysis shows that the model has good calculation speed, fitting and prediction accuracy and it can effectively mine the date char-acteristics inherent in the measured deformation, and reduce the influence of noise components on the modeling accuracy.

Adequate energy intake is critical for the healthy longevity of older adults, and the estimated energy requirement is determined by total energy expenditure (TEE). We aimed to identify the relationship between measured aerobic capacity and TEE, activity energy expenditure (AEE) or physical activity level (PAL) with the doubly labeled water (DLW) methods in the advanced older adults. A total of 12 physically independent older adults (10 males and 2 females) aged between 81 to 94 years participated in this study. Aerobic capacity was evaluated according to the lactate threshold (LT). TEE under free-living conditions was assessed using the DLW method, and self-reported physical activity was obtained through the Japanese version of the International Physical Activity Questionnaire (IPAQ). LT was significantly positively correlated with TEE, AEE, and PAL after adjustment for age and sex (ρ= 0.77 (P<0.01), 0.86 (p<0.01), and 0.86 (p<0.01), respectively). We found the LT as an aerobic capacity is positively and independently correlated with TEE, AEE or PAL. The present results suggest that maintaining aerobic capacity is an important factor for preventing frailty, although further research is needed to multisite studies and many samples.

Correlations between the air permeability coefficient and various pore structure indicators in cementitious materials were examined to determine the pore structure indicator that best evaluated air permeability using data from previous studies of air permeabilities and pore structures. The determination coefficients of air permeability with total pore volume, critical pore diameter, and ordinary threshold pore diameter were low, although these have often been used as indicators. The median and threshold pore diameters obtained by percolation theory showed high determination coefficients. The equation using the threshold pore diameter better estimated the air permeability coefficient than the Katz–Thompson equation.

Sustainable energy development (SED) is a crucial component of the Sustainable Development Goals (SDG), aiming to maintain economic and social progress while protecting the environment and mitigating climate change’s effects. SED serves as a transition paradigm for sustainable development, providing a blueprint for energy peace and prosperity for people and all uses. This article presents the history of SED and then uses a critical discourse approach to summarize existing review studies in SED. Ten interlinked themes of SED are identified, with two of them considered to be among the least studied in existing SED reviews and in the current global discussion around climate change. This study explores these two themes, which include energy financing and the need for 100% renewable energy (RE), a sub-theme of decarbonization strategy working towards the 1.5–2.0 °C scenario. The study suggests that the current G20 countries’ contributions, if maintained continuously per annum, in addition to 80% more funding from private investment compared to the amount in the 1.5 °C scenario financial requirements for clean energy, are sufficient to limit global warming. In addition to the present drive for 100% RE, the article also discusses emerging issues, such as energy storage options with an indication of hydrogen as the most promising, other energy-related development agendas, and the need for regional security stability to prevent energy wars. Selected SED decarbonization strategies are presented across the power, transport, building, and industrial sectors. The study concludes with progress and directions for future research, mainly the need for re-defining nationally determined contribution (NDC) through an emissions budgeting and centralized global or regional emissions stock-taking strategy working towards the 1.5 °C scenario.

The high demand for SARS-CoV-2 tests but limited supply to South African laboratories early in the COVID19 pandemic, resulted in a heterogenous diagnostic footprint of open and closed molecular testing platforms. Novel approaches were required to monitor test quality especially during the introduction of newly circulating variants. The National Health Laboratory Service centrally collected cycle threshold (Ct) values from 1,497,669 test results reported from six commonly used PCR assays in 36 months, and visually monitored changes in their median Ct within a 28-day centered moving average for each assays’ gene targets. This continuous quality monitoring rapidly identified delayed hybridization of RdRp in the Allplex™ SARS-CoV-2 assay due to the Delta (B.1.617.2) variant; S-gene target failure in the TaqPath™ COVID-19 assay due to B.1.1.7 (Alpha) and the B.1.1.529 (Omicron); and recently E-gene delayed hybridization in the Xpert® Xpress SARS-CoV-2 due to XBB.1.5. This near “real-time” monitoring helped inform the need for sequencing and the importance of multiplex molecular nucleic acid amplification technology designs used in diagnostics for patient care. This continuous quality monitoring approach at the granularity of Ct values should be included in ongoing surveillance and with application to other disease use cases that rely on molecular diagnostics.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

The sonification of data to communicate information to a user is a relatively new approach that established itself around the 1990s. To date many researchers design their individual sonification from scratch. There are no standards in sonification design and evaluation. But researchers and practitioners have formulated several requirements and established several methods. There is wide consensus that psychoaocustics could play an important role in the sonification design and evaluation phase. But this requires an adaption of psychoacoustic methods to the signal types and the requirements of sonification. In this method paper we present PAMPAS, a PsychoAcoustical Method for the Perceptual Analysis of multidimensional Sonification. A well-defined and well-established, efficient, reliable and replicable Just Noticeable Difference experiment using the Maximum Likelihood Procedure serves as the basis to achieve linearity of parameter mapping during the sonification design stage and to identify and quantify perceptual effects during the sonification evaluation stage, namely the perceptual resolution, hysteresis effects and perceptual interferences. The experiment results are universal scores from a standardized data space and a standardized procedure. These scores can serve to compare multiple sonification designs of a single researcher, or even between different research groups. The method can supplement other sonification design and evaluation methods from a perceptual viewpoint.

Modified structure along latent tracks and track formation process have been investigated in poly(allyl diglycol carbonate), PADC, which is well recognized as a sensitive etched track detector. This knowledge is essential to develop novel detectors with improved track registration property. The track structures of protons and heavy ions (He, C, Ne, Ar, Fe, Kr and Xe) have been examined by means of FT-IR spectrometry, covering the stopping power region between 1.2 to 12,000 eV/nm. Through a set of experiments on low-LET radiations – such as gamma ray -, multi-step damage process by electron hits was confirmed in the radiation-sensitive parts of the PADC repeat-unit. From this result, we unveiled for the first-time the layered structure in tracks, in relation with the number of secondary electrons. We also proved that etch pit was formed when at least two repeat-units were destroyed along the track radial direction. To evaluate the number of secondary electrons around tracks, a series of numerical simulations were performed with Geant4-DNA. Therefore, we are proposing new physical criterions to describe the detection thresholds. Futhermore, we propose a present issue of the definition of detection threshold for semi-relativistic C ions. And as a possible chemical criterion, formation density of hydroxyl group is suggested to express the response of PADC.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

The development of mineral resources in China has gradually entered the stage of deep mining. Rock burst, collapse and other ground pressure disasters caused by deep high stress have become major hidden dangers restricting mine safety production. Microseismic monitoring technology is an important means of ground pressure risk prediction. In this paper, the wavelet coefficient threshold denoising method in time-frequency domain, STA/LTA method, AIC method, Skew and Kurtosis method are studied, and the automatic P-phase onset time picking model based on noise reduction and multiple detection indexes is established. Through the effect analysis of microseismic signals collected by microseismic monitoring system of coral Tungsten Mine in Guangxi, automatic P-phase onset time picking is realized. the reliability of the P-phase onset time picking method proposed in this paper based on noise reduction and multiple detection indexes is verified. The picking accuracy can still be guaranteed under the severe signal interference of background noise, power frequency interference and manual activity underground mine, Which is of great significance to the data processing and analysis of microseismic monitoring.

The objective of this paper is to research the impact of electrical and physical parameters that characterize the complementary MOSFET transistors (NMOS and PMOS transistors) in the CMOS inverter for static mode of operation. In addition to this, the paper also aims at exploring the directives that are to be followed during the design phase of the CMOS inverters that enable designers to design the CMOS inverters with the best possible performance, depending on operation conditions. The CMOS inverter designed with the best possible features also enables the designing of the CMOS logic circuits with the best possible performance, according to the operation conditions and designers’ requirements.

This paper identifies a criterion for choosing the largest set of rejected hypotheses in high-dimensional data analysis where Multiple Hypothesis testing is used in exploratory research to identify significant associations among many variables. The method neither requires predetermined thresholds for level of significance, nor uses presumed thresholds for false discovery rate. The upper limit for number of rejected hypotheses is determined by finding maximum difference between expected true hypotheses and false hypotheses among all possible sets of rejected hypotheses. Methods of choosing a reasonable number of rejected hypotheses and application to non-parametric analysis of ordinal survey data are presented.

Monitoring crown closure evolution using multi-temporal Light Detection and Ranging (LiDAR) surveys is a method that we expect to be increasingly adopted given the availability of LiDAR sensors and the accumulating survey archives. However, little attention was devoted to comparing crown closure estimates from independent surveys. Although survey parameters cannot be modified after the data collection, we speculate that the error associated to crown closure estimates comparison can be reduced by selecting optimal post-survey parameters. In this study, we compared crown closure estimates of three airborne LiDAR surveys from 2018 (40 pt/m²) used as a reference, and two lower-density surveys from 2016 (4.5 pt/m²) and 2018 (2 pt/m²). We studied the effect of the height threshold used to separate canopy points and the grid resolution, using skewness and variance of lagged difference of crown closure. Crown closure estimates using low height thresholds were more different across surveys, resulting in higher root mean squared error (RMSE), bias and more different variograms. Results show that optimal height threshold was 3 m and grid resolution was 25 m, although there was room for decision (RMSE of 7% and 5%, and bias of 4% and 0% for 2016 and 2018 low-density surveys).

Finding out how cells with the same genome change fates in differentiation commitment is a challenge of biology. We used MCF-7 breast cancer cells treated with the ErbB2 ligand heregulin (HRG), which induces differentiation, to address if and how the constitutive pericentromere-associated domains (PADs) may be involved in this process. PAD-specific repressive heterochromatin (H3K9me3) and active euchromatin (H3K4me3) marking, centromere (CENPA) labelling, qPCR, acridine-orange-DNA structural test, and microscopic image analysis were applied. We found a two-step DNA unfolding, at 15-20 min and 60 min after HRG treatment, coinciding with bi-phasic activation of the early response genes (c-FOS family) and two steps of critical phase transition which were revealed in transcriptome studies. In control, the distribution of PAD number and size displays a power-law scaling with a boundary at the nucleolus. PADs’ clustering correlates with centromere numbers. 15 min after HRG treatment, the unravelling of PADs occurs, coinciding with the first step of euchromatin unfolding. The second step is associated with transcription of long-non-coding-RNA from satellite III DNA. We hypothesize that splitting of the PAD clusters under the critical size threshold of the silencing domain abrupts position effect variegation. It allows the first genome transcription avalanche to occur, starting differentiation commitment.

Electrically conductive adhesives (ECA’s) are used widely to replace or reinforce lead soldering or conductive metal components in electronic packaging applications such as die attachment, solderless interconnections, component repair, display interconnections, and heat dissipation. Their conductive behavior as well as the associated behaviors such as heat conduction and mechanical behavior (strength, rigidity, deformation and viscoelastic behavior, which may be affected by moisture ingression) are affected by adhesive film thickness, volume fraction, size and shape of the conductive filler, as well as uncured base adhesive viscosity, substrate and filler surface treatment and the applied pressure (during bonding and during conduction). The adhesive resistivity decreases precipitously above a characteristic filler volume fraction called the percolation threshold. In general, micron-sized metal fillers mixed in an adhesive (often an epoxy) resulting with different film thicknesses exhibit thickness thresholds for transition from three-dimensional conductivity to two-dimensional conductivity with considerable increases in thickness-direction (z-axis) resistivity when the film thicknesses are smaller than these threshold values. Recently, the use of conductive nanoparticles allowed decreases in percolation threshold levels as well as increases in mechanical strength and durability of ECA’s. Most ECA’s are supplied in liquid or paste form in varying viscosities and therefore, the method of their application also affects their performance. This work intends to provide an understanding of these effects on conduction behavior in (usually high-priced) equipment in which they are used.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.