The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

The decarbonization of the electrical energy sector is in progress for contrasting the climate changes, with a relevant increase of the Renewable Energy Sources (RES) power plants, mostly in Dispersed Generation (DG). The adequacy and the security of power systems, with a huge penetration of RES in DG is possible with a suitable integration of energy storage. In fact, energy storages are able to provide many different services for long-term adequacy and real time security. In this framework the present paper deals with a Thermal Energy Storage (TES) proposed for power system services. The technology presented is made up of modules containing a bed of fluidizable solid particles, which can store thermal energy from waste heat, process heat and/or from electricity. Stored thermal energy can be released, e.g. as superheated steam, for thermal uses or converted into electricity, by means of steam turbines. Some possible applications are then reported explaining advantages and limits.

Maxwell equations governing electromagnetic effects are being shown to be equivalent to the compressible inviscid Navier-Stokes equations applicable in fluid dynamics and representing conservation of mass and linear momentum. The latter applies subject to a generalized Beltrami condition to be satisfied by the magnetic field. This equivalence indicates that the compressible inviscid Navier-Stokes equations are Lorentz invariant as they derive directly from the Lorentz invariant Maxwell equations subject to the same Beltrami condition. In addition, the derivation results provide support for the claim that electromagnetic potentials have physical significance as demonstrated by Aharonov-Bohm effect, and are not only a convenient mathematical formulation.

Temporary streams are a key component of the hydrological cycle in arid and semi-arid regions, but their flow is highly variable and difficult to measure. In this paper, we present a novel approach that could be used to assess the flow of temporary streams and characterize their environmental status. Specifically, we apply the Image Velocimetry method to estimate surface velocity in temporary streams using unmanned aerial vehicles (UAVs) equipped with optical sensors (IV-UAV method). The IV-UAV method enables the easy, safe and quick estimation of the velocity on the water’s surface. This method was applied in different temporary streams in Lesvos Island, Greece. The produced results show that the IV-UAV can be implemented at low discharges, at temporary streams and at small streams. However, there were many occasions that measurements were unable due to various reasons such as dense vegetation or archaeological sites. Despite of this, the proposed methodology could be incorporated in optical protocols which are used to assess the environmental status of temporary streams of Mediterranean conditions. Finally, this would become a valuable tool for understanding the dynamics of these eco-systems and monitoring changes over time.

This paper provides an optimization strategy for flexible operation at the system level, so as to guide the real-time flexible ramping of the power grid. Firstly, the concept of regional power grid flexibility was clarified, and the ramping factor is proposed as a flexibility metric. On this basis, taking the output priority of each node as the objective function and considering constraints such as line flow, power balance, and system flexibility, a mathematical model for regional power grid transmitting flexible power externally is proposed. Compare with the traditional models, this model focuses more on flexibility rather than economy. The case analysis based on the improved IEEE 30-Bus System verifies the feasibility and effectiveness of the proposed strategy and its advantages over the traditional models.

Wireless communications are gaining massive demand for faster video streaming, virtual reality, and 5G-based IoT (Internet of Things) applications. Due to this network congestion increases hastily. The demand for user-specific services, machine learning, forcing the radio access network (RAN) to provide improvement in utilization of spectrum efficiency, minimizing power consumption, and improving data rate. For LTE/LTE-A network specifications provided by third-generation partnership project (3GPP), guarantees to provide qualitative of service (QoS). Release 15/16 utilizes two-dimensional (2D) active antenna array systems (AAS). This kind of AAS provides beam forming in both azimuth and elevation also termed as Full Dimensional MIMO (FD-MIMO). It enhances the radiation pattern of the antenna array element by adjusting the angular power spectra at the base station (BS), it also allows selecting the minimum number of antennas for effective beam forming toward specific user equipment’s (UEs). Spectrum allocation challenge can be dealt with at mm wave band having FR2 (>6GHz) frequency band specified by International Telecommunication Union (ITU-R) in line with IMT-2020 specifications. The spectrum is free at mm Wave for communication of 5G. However, the main challenge is, it faces path loss and atmospheric loss electromagnetic energy absorbed by gases like oxygen. In this work, the 5G new RAN power spectrum and power delay profile at 10GHz carrier frequency with 20MHz to 100MHz channel bandwidth is observed for line of sight (LOS) and non-line of sight (NLOS) communication for guaranteed QoS. To demonstrate the path loss and power delay profile (PDP) in directional and Omni-directional antennas NYUSIM channel simulator is utilized.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

In this paper, the power quality of interconnected microgrids is managed using a Model Predictive Control (MPC) methodology which manipulates the power converters of the microgrids in order to achieve the requirements. The control algorithm is developed for the microgrids working modes: grid-connected, islanded and interconnected. The results and simulations are also applied to the transition between the different working modes. In order to show the potential of the control algorithm, a comparison study is carried out with classical Proportional-Integral Pulse Width Modulation (PI-PWM) based controllers. The proposed control algorithm not only improves the transient response in comparison with classical methods but also shows an optimal behavior in all the working modes, minimizing the harmonics content in current and voltage even with the presence of non-balanced and non-harmonic-free three-phase voltage and current systems

The discrete element method (DEM) coupled with computational dynamics (CFD) has been considered one of the most sensitive ways of studying fluidized beds. This paper presents gas-solid fluidized bed simulations by use of CFD-DEM. The two-phase interaction is calculated in a way of decoupling. Within the effective neighborhood of the particles, the kernel approximation method is used to calculate the local porosity, thereby calculating the drag force on the particles. At the grid scale, the momentum exchange coefficient is calculated using a two fluid model based method, thereby calculating the source term of the phase interaction in the fluid control equation. The simulated form, size and motion process of the big bubble are all consistent with experimental observations. The simulated solid volume fraction and relative pressure averaged in a horizontal plane at 45 mm above the bottom are in reasonable agreement with the experimental data. The fluctuation of the simulated bed height over time is similar to the experimental measurement results. The reproduction of these qualitative and quantitative results indicates that the proposed method effectively improves simulation performance and accuracy.

Active flow control is a promising technology for reducing noise, emissions, and power consumption in various applications. To better understand the performance of synthetic jet actuators, a computational model that couples structural mechanics with electrostatics, pressure acoustics, and fluid dynamics has been needed. The model presented here has been validated against experimental data and then used to investigate the fluid behavior inside and outside the synthetic jet actuator cavity, impacts of thermoviscous losses on capturing the acoustic response of the actuator, and viability of different modeling methods of diaphragms in computational simulations. The results capture the feedback from the fluid onto the diaphragm and highlight the need for careful acoustic modeling.

Material and methods. The trial was carried out over two years in Southern Italy. Two grapevine rootstocks, 110R and SO4, were compared to evaluate the water extraction ability from the soil and the effect on the yield and quality of the Cardinal grapevine table cultivar. Therefore, a new approach to plant water consumption based on sap flow was adopted. Results. The earlier and faster water refilling of the xylem in Cardinal onto 110R (C/110R) appears responsible for the earlier evolution of the phenological phases than Cardinal onto SO4 (C/SO4). The maximum length of the principal shoot was reached in Cardinal/110R compared to C/SO4, while a higher number of lateral shoots with lower internode has changed canopy architecture and light distribution in C/SO4. The 110R used more water compared to SO4; it was possible to quantify the real transpired flux of the plant per day: sap flow was 12.3 L.plant-1.d-1 and 11.7 L.plant-1d-1 in C/110R in the first and second year, respectively, while it was 14% lower in alternative graft combination. Conclusions. However, C/SO4 was able to sustain leaf water status and physiological mecha-nisms, although with lesser performance than C/110R, but that did not cause negative effects on production parameters.

With the wide application of flow sensor, their reliability under extreme conditions has been concerned in recent years. The reliability of a Micro Electro Mechanical Systems flow sensor under temperature (Ts) is researched in this paper. Firstly, the Step-stress accelerated degradation test is designed. Because this flow sensor consists flow sensor chip and signal processing system, the accelerated degradation testing is implemented, respectively. While the results show that the biggest drift is 3.15% for flow sensor chips with 150℃ conditions, and 32.91% for this flowmeter. By analysis, it could be found that the attenuation of the signal processing system is significant to the degeneration of this flowmeter. The minimum drift of the signal processing system accounts for 82.01% of this flowmeter. Secondly, using the Coffin-Manson model, the relationship between cycle-index and Ts is established. And the lifetime with different Ts is estimated by the Arrhenius model. In addition, the Weibull distribution is applied to evaluate the lifetime distribution. Finally, the reliability function of the Weibull distribution is demonstrated, and the survival rate within one year is 87.69% with 85℃ conditions. Thus, by the application of accelerated degradation testing, the acquired results are innovative and original. This research illustrates the reliability research, which provides a relational database for the application of this flow sensor.

Background: Poor patient flow can lead to adverse outcomes for patients and organisational inefficiency. Many hospitals have addressed suboptimal patient flow by increasing resourcing, such as bed stock and staffing, however, this is an unsustainable approach. In determining the nature of poor patient flow issues, it is important to collect data from healthcare professionals who manage patient flow on a daily basis. Doing so provides insights into the current state of patient flow management in its entirety, whilst also helping with the development of sustainable solutions.; Methods: Thirteen semi-structured interviews were conducted with clinicians who were directly involved with patient flow at a tertiary care centre in Tasmania, Australia. Results: Through a thematic analysis method, four major themes were developed: managing patient flow, communication for decisions, tools as enablers and barriers and increasing complexity. Conclusions: The findings of this study provide great insights into patient flow issues, with potential solutions identified to address them.

This paper presents the results of simulations of particle-laden air-solid jet flow in long straight tubes using CFD-DEM, along with an analysis of coarse-graining. Although previous studies have used CFD-DEM for similar flows, these have typically been in a dilute flow regime where uncoupled simulations are accurate. However, fully coupled simulations can introduce issues, necessitating validation studies to ensure that all coupling parameters are effectively used and that the physics is accurately represented. This paper validates the simulations against two different experimental studies, with fluid Reynolds numbers between 10,000 and 40,000 and Stokes numbers between 5.6 and 50. Interestingly, the profiles of mean particle velocity exhibit fewer discrepancies as the Stokes number increases but more discrepancies for the root mean square velocity compared to the experiments. Particle number flux is consistent with the experiments after the nozzle exit. Coarse-graining is also applied to the same simulations, achieving relatively accurate results. However, as expected, scaling of contact collision frequencies, forces, and stresses cannot be achieved, meaning that coarse-graining may be useful for comparing designs or operating parameters on an industrial scale but falls short when measuring the total energy dissipation of one experiment.

Gas embolism is a medical condition leading to the blockage of blood flow in the microvasculature by gas bubbles. While reported as rare, gas embolism often has devastating, fatal physiological consequences. Despite this acute importance, the genesis and evolution of air bubbles in blood vessels under different physiological conditions, such as blood viscosity and blood flow rate, is still understudied, largely because of difficult experimentation and in situ visualization. The objective of this work was to study the gas embolism phenomenon in vitro, using a microfluidic system that mimicked the architecture of microvasculature. The microfluidic systems comprised linear channels with two different air inlet types, namely, T- and Y-junctions with three different widths (20 µm, 40 µm, and 60 µm), and a 30 µm width honeycombed network with three bifurcation angles (30°, 60°, and 90°). Three synthetic liquids equivalent to 0%, 20%, and 46% hematocrit that mimicked the physiological blood viscosity and hematocrit concentrations were used. Our results show that: (i) 20 µm and 40 µm width channels had an elevated risk of gas embolism due to wide fluctuations in the total slug sizes; (ii) the resistance to the flow of air bubbles increased with the increase in the equivalent concentration of hematocrit; (iii) gas bubbles causing blockages and dampening of the flow velocity were frequently observed in 20 µm channels, and lastly (iv) increased risk of gas embolism was observed in the honeycomb architecture with 60° and 30° bifurcations. This work suggests that in vitro experimentation using microfluidic devices with microvascular tissue-like structures opens the possibility of studying this medical condition with high reproducibility and impacts the fact-based medical guidelines for preventing or mitigating iatrogenic occurrences.

This paper presents an analysis of linear viscous stress Favre-Averaged turbulence models for computational fluid dynamics (CFD) of fully turbulent round jets with a long straight tube geometry in the near field. Although similar work has been performed in the past with very relevant solutions, considerations were not given for the issues and limitations involved with coupling between an Eulerian and Lagrangian phase, such as in fully two-way coupled CFD-DEM. These issues include limitations on solution domain, mesh cell size, wall modelling, and momentum coupling between the two phases in relation to the particles size. Therefore, within these considerations, solutions are provided to the Navier-Stokes equations with various turbulence models using a three-dimensional wedge long straight tube geometry for fully developed turbulence flow. Simulations are performed with a Reynolds number of 15000 and 50000 using two different tube diameters. It is found that a modified k−ε turbulence model achieved the most agreeable results for both the velocity and turbulent flow fields between these two flow regimes, while a modified k−ω SST/BSL also provided suitable results.

Evidence supports an association between low magnesium (Mg) intake and coronary heart disease and between Mg intake and endothelial function. The aim of this study was to assess the effect of one week of Mg supplementation on endothelial function, assessed by flow mediated dilatation (FMD). Nineteen healthy men and women completed this cross-over pilot study in which participants were randomised to take an over-the-counter magnesium supplement for one week or to follow their usual diet. Weight, FMD and blood pressure (BP) were taken on completion of each intervention and 24hour urine collections and blood samples were taken to assess compliance. Baseline serum Mg was within normal range for all participants. Urinary Mg and urinary magnesium-creatinine ratio (Mg/Cr) significantly increased between interventions, (p = 0.03, p = 0.005 respectively). No significant differences in FMD or BP were found between the interventions. A significant negative correlation was seen between age and FMD (r = -0.496, p = 0.031). When adjusted for age, saturated fat was negatively associated with FMD (p = 0.045). One week of Mg supplementation did not improve FMD in a healthy population.

Evidence supports an association between low magnesium (Mg) intake and coronary heart disease and between Mg intake and endothelial function. The aim of this study was to assess the effect of one week of Mg supplementation on endothelial function, assessed by flow mediated dilatation (FMD). Nineteen healthy men and women completed this cross-over pilot study in which participants were randomised to take an over-the-counter magnesium supplement for one week or to follow their usual diet. Weight, FMD and blood pressure (BP) were taken on completion of each intervention and 24hour urine collections and blood samples were taken to assess compliance. Baseline serum Mg was within normal range for all participants. Urinary Mg and urinary magnesium-creatinine ratio (Mg/Cr) significantly increased between interventions, (p = 0.03, p = 0.005 respectively). No significant differences in FMD or BP were found between the interventions. A significant negative correlation was seen between age and FMD (r = -0.496, p = 0.031). When adjusted for age, saturated fat was negatively associated with FMD (p = 0.045). One week of Mg supplementation did not improve FMD in a healthy population.

Magnesium (Mg) deficiency may be a catalyst in the process of endothelial dysfunction, an early event in the pathogenesis of atherosclerosis. The aim was to determine the acute effect of an oral Mg supplement compared to control on endothelieal function assessed by flow-mediated-dilatation (FMD). Nineteen participants (39 years, body mass index (BMI) 22.9kg/m2) completed this randomised cross-over study. Blood pressure (BP) and FMD were measured and blood samples taken before participants drank 200ml water with or without an over the counter Mg supplement (450mg and 300mg for men and women). Measurements were repeated at 60 and 120 minutes. There was a statistically significant two-way interaction between treatment and time on serum Mg (p = .037). A difference of -0.085mm in FMD was observed 60 minutes post drink in the control group compared to baseline FMD, and no difference was observed in the supplement group compared to baseline. Despite the non-significant interaction between treatment and time on FMD, the difference seen in the control group and the lack of change in the supplement group at 60 minutes post-drink suggests that Mg may attenuate the reduction in FMD post-prandially.

89Zr-radiolabelled proteins functionalised with desferrioxamine B are a cornerstone of diagnostic positron emission tomography. In the clinical setting, 89Zr-labelled proteins are produced manually. Here, we explore the potential of using a microfluidic photochemical flow reactor to prepare 89Zr-radiolabelled proteins. The light-induced functionalisation and 89Zr-radiolabelling of human serum albumin ([89Zr]ZrDFO-PEG3-Et-azepin-HSA) was achieved by flow photochemistry with a decay-corrected radiochemical yield (RCY) of 31.2±1.3% (n = 3) and radiochemical purity >90%. In comparison, a manual batch photoreactor synthesis produced the same radiotracer in a decay-corrected RCY of 59.6±3.6% (n = 3) with an equivalent RCP >90%. The results indicate that photoradiolabelling in flow is a feasible platform for the automated production of protein-based 89Zr-radiotracers, but further refinement of the apparatus, and optimisation of the method is required before the flow process is competitive with manual reactions.

The objective of this work is to evaluate the impact of the innovative modifications made to the conventional effluent capture and discharge devices used in subsurface flow wetlands (SSFW). The main modifications developed consist on extending the influence of the capture and discharge device in such a way that the SSFW width and height are fully covered. This improved innovative device was applied and evaluated in two subsurface flow wetlands, one on a pilot scale and one on a real scale. To evaluate the impact of the innovative device with respect to conventional one in the operational functioning of subsurface flow wetlands, the elimination of chemical oxygen demand was measured and compared. The results show that for the innovative device, the COD removal was 10% higher than for the conventional device, confirming the validity and effectiveness of the modifications implemented in the effluent capture and discharge devices used in SSFW.

The hydrodynamic results obtained from the permeability of porous materials not only affect the assessment of the stream of the gas flow through those materials but they also refer to the loss of pressure energy in that flow. The direct measure of that loss is flow resistances.The results of experimental research upon the assessment of the flow resistances of porous materials with respect to gas flow. The research conducted applied to natural materials with an anisotropic gap-porous structure. The tests were carried out on a gas permeability measuring system, adapted to different shapes of porous material samples. The process issue of the total pressure drop on a porous deposit was considered in the Reynolds number category. The coefficient of flow resistance for anisotropic materials was defined and the value of this coefficient was compared to the gas stream and the total pressure drop on the porous bed was experimentally evaluated.

Simulation programs contain Computational Fluid Dynamics - CFD codes and are a useful tool used for gas flow through porous materials. Conducting numerical simulations allows for detailed analysis of hydrodynamic phenomena. The results of numerical modeling should always be verifiable based on experimental data. Only their compliance with the results of experimental tests is a determinant of the correctness of the applied method. As part of the work, experimental studies of hydrodynamics of gas flow through an isotropic porous material were carried out and numerical simulation for material of the same shape was used. In the CFD modeling Kolmogorov's hypothesis for the transport of kinetic energy of turbulence k and transport of dissipation rate of kinetic energy of turbulence ε was used.

The aim of this work is to evaluate the impact of proposed modifications to conventional capturing and discharging effluents devices in Subsurface Flow Wetland (SSFW) systems. Main modifications proposed consist on extending the influence of the capture and discharge device in such a way that the SSFW width and height are fully covered. Additionally an SSFW prototype was built as pilot including the proposed modifications and the impact of the innovative device is measured based on the efficiency of the Chemical Oxygen Demand (COD) removal as compared to a traditionally built SSFW. The results show that for the innovative device, the COD removal was 10% higher than for the conventional device.

In this paper, we studied and analyzed the behavior of velocity profiles and the distribution of pressures in a pipe connected to an accessory. In this case, it was a 90º elbow fitting in which water flows as an incompressible flow. This study was developed numerically through the fluent program of ANSYS. It is of practical interest in engineering because it is based on results regarding the internal structure of a model of incompressible flows. In the same way, it provides a basis for the proper design and implementation of velocity profiles within an elbow.In the agricultural industry, suitable systems can be implemented for crop irrigation in this way with the results obtained to improve the design in the fluid distribution system.We used a feasible κ-ε turbulence model because this model causes less turbulence than the standard κ-ε model. A mesh independence study was developed, in which it was observed that combining different densities of meshes for the same geometry causes some variables, so a fine meshing was used to carry out the study so that the results are as close to reality as possible.

Expressions for the axial pressure profiles in a cylindrical channel and between parallel plates or a rectangular channel with large aspect ratio, with Maxwell slip gas flow are derived from first principles. The resulting expressions, which only involve the inlet and outlet pressures and the channel dimensions, will be useful in modelling or simulations of channel flows at Knudsen numbers in the range 0.001–0.1, such as in MEMS and NEMS. The expression for a cylindrical channel is validated by deriving from it an expression for the channel mass flow, which is shown to agree with a known expression for the mass flow through cylindrical channels with Maxwell slip flow. The expression for flow between parallel plates is found to agree with the zeroth order relation derived by Arkilic et al. using perturbation analysis. The effect of the accommodation coefficient on the pressure profile in a cylindrical channel is shown.

In ultra-relativistic collisions of heavy ions, the strongly interacting Quark Gluon Plasma (sQGP) is created. The fluid nature of the sQGP was one of the important discoveries of high energy heavy ion physics in the last decades. Henceforth the explosion of this matter may be described by hydrodynamical models. Besides numerical simulations, it is important to study the analytic solutions of the equations of hydrodynamics, as these enable us to understand the connection of the final and initial states better. In this paper we present a perturbative, accelerating solution of relativistic hydrodynamics, on top of a known class of solutions describing Hubble-expansion. We describe the properties of this class of perturbative solutions, and investigate a few selected solutions in detail.

This paper discusses wind tunnel test results aimed at advancing active flow control technology to increase the aerodynamic efficiency of an aircraft during take-off. A model of the outer section of a representative civil airliner wing was equipped with two-stage fluidic actuators between the slat edge and wing tip, where mechanical high-lift devices fail to integrate. The experiments were conducted at a nominal take-off Mach number of M = 0.2. At this incidence velocity, separation on the wing section, accompanied by increased drag, is triggered by the strong slat edge vortex at high angles of attack. On the basis of global force measurements and local static pressure data, the effect of pulsed blowing on the complex flow is evaluated, considering various momentum coefficients and spanwise distributions of the actuation effort. It is shown that through local intensification of forcing, a momentum coefficient of less than c_μ = 0.6% suffices to offset the stall by 2.4°, increase the maximum lift by more than 10%, and reduce the drag by 37% compared to the uncontrolled flow.

Let be a power function $f_{r,M}(s)$ defined for every $s$ within the finite set $M$ as follows $$f_{r,M}(s)= \begin{cases} s^r, \ &s\in M,\\ 0, \ &\mathrm{otherwise}. \end{cases} $$ Let a discrete convolution of $f_{r,M}(s)$ be denoted as follows $\mathrm{Conv}_{r,M}[n]=(f_{r,M}*f_{r,M})[n]$. Let a real coefficients $A_{m,j}$ be given by the following recurrence $$ A_{m,j} = \begin{cases} 0, & \mathrm{if } \ j<0 \ \mathrm{or } \ j>m, \\ (2j+1)\binom{2j}{j} \sum_{d=2j+1}^{m} A_{m,d} \binom{d}{2j+1} \frac{(-1)^{d-1}}{d-j} B_{2d-2j}, & \mathrm{if } \ 0 \leq j < m, \\ (2j+1)\binom{2j}{j}, & \mathrm{if } \ j=m. \end{cases} $$ In this paper we show that for every $n>0$ the following odd-power identities involving coefficients $A_{m,j}$ and convolution transform $\mathrm{Conv}_{r,M}[n]$ hold $$ \begin{split} n^{2m+1}+1&=\sum_{r=0}^{m}A_{m,r}\mathrm{Conv}_{r,\mathbb{N}}[n],\\ n^{2m+1}-1&=\sum_{r=0}^{m}A_{m,r}\mathrm{Conv}_{r,\mathbb{Z}_{>0}}[n],\\ n^{2m+1}&=\sum_{r=0}^{m}A_{m,r}\sum_{k=1}^{n} k^r(n-k)^r\\ &=\sum_{r=0}^{m}A_{m,r}\sum_{k=0}^{n-1} k^r(n-k)^r. \end{split} $$

Non-normal mode stability analysis has long been employed to study linear transient characteristics of wall bounded shear flows. However, the application of this approach to investigate shear flows with stratified thermal conditions (STCF) has received limited attention. This paper examines thermal effects on Taylor-Couette flow. The results in this study indicate the possibility of a subcritical bifurcation in stratified Taylor-Couette flow.

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

Mobile robots can perform tasks on the move, including exploring terrain, discovering landmark features or moving a load from one place to another. This group of robots is characterized by a certain level of intelligence allowing making decisions and responding to stimuli received from the environment. As part of Industry 5.0, such mobile robots and humans are expected to co-exist and work together in a shared environment to make human work less tiring, quicker, and safer. This can only be realized when clean, dense, and economical energy sources are available. The aim of the study is to analyze the state of the art and to identify the most important directions for future developments in robotic power systems based mainly on batteries. The efficiency and performance of the battery depends on the design using different materials. Work environments and performance requirements are considered in this systematic review to classify solutions that help developers choose the best suited power system for specific application. Indirectly, the aim of the work is to generate discussion within the scientific and engineering community. A narrative review of publications from six major bibliographic databases according to preset inclusion criteria was combined with a critical analysis of current and future technologies. The main findings of the review allow answering question what is the role of modern power source technologies, artificial intelligence and ground-breaking research work in global policies related to energy saving, green policies, and sustainable development. The main opportunities and threats are discussed, and a brief feasibility analysis is carried out. Novelty of the article relates not only to the analysis of technologies, but also to approaches and their use under conditions of limited resource availability, when resource usage must be minimized. The article provides an overview of batteries, their specifications, classifications, and their advantages and disadvantages. In addition, we propose: (1) an algorithm for selecting main energy source for robot application, and (2) an algorithm for selecting electrical system power supply. Current mobile robot batteries are, in most cases, their biggest limitation. Progress in batteries development is too slow to catch up with the demand for robot autonomy and range requirements, limiting the development of mobile robots. Further intensive research and implementation work is needed to avoid years of delay in this area.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

Penetration of grid connected inverters (GCI) has arisen in power systems due to increasing integration of renewable sources. However, restrictive grid codes require that renewable sources connected to the grid with power electronic systems must be properly connected and appropriate currents must be injected to support stability of the grid under grid faults. Simultaneous injection of symmetrical positive and negative sequence currents is mandatory to support stabilization of grid at the instant of grid faults. Conventional synchronously rotating frame dq current controllers are insufficient under grid faults due to low bandwidth of PI controllers. This paper proposes a new grid current control strategy for grid connected voltage source inverters under unbalanced grid voltage conditions. A proportional current controller with a first order low pass filter disturbance observer (DOb) is proposed which establishes positive sequence power requirements and independently control negative sequence current components under unbalanced voltage conditions. The method does not need any parameter, since it estimates nonlinear terms with low pass filter DOb. Simulations are implemented in Matlab/Simulink platform demonstrating the effectiveness of proposed method.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

Given the imperative of security, sustainability of supply, strategic considerations, and energy independence, there is a widely acknowledged need to persist in utilizing coal as the primary fuel for electricity generation in power plants. However, in order to combat the rising levels of CO2 in the atmosphere, it is crucial to advance the development of carbon capture and storage (CCS) technologies that enable fossil fuel power plants to achieve zero emissions. These technologies play a pivotal role in capturing and effectively storing CO2, thus ensuring that coal-based power generation can continue while significantly reducing its environmental impact. By implementing CCS solutions, fossil fuel power plants can transition towards a more sustainable and environmentally friendly energy future.The utilization of chemical solvents for CO2 absorption, coupled with long-term storage, presents an intriguing and commercially viable technology for CO2 capture. However, the significant energy demands of the solvent regeneration process necessitate optimization, particularly in large-scale power plants. While the current cost of CO2 capture stands at approximately #55,000.00(Naira) per ton of CO2, the objective is to reduce this cost to below #25,000.00(Naira) per ton of CO2. This reduction in cost is essential to ensure the economic feasibility and widespread adoption of CO2 capture technologies in power generation.This research paper explores various approaches to address the energy demands associated with amine scrubbing integration in a commercial power plant. It provides a comprehensive analysis, both technically and economically, of the performance of these different approaches. While some of the proposed schemes may result in minor efficiency reductions, the key objective is to calculate the specific cost per ton of CO2 captured. The primary focus is on identifying the most suitable configuration to implement large-scale, cost-effective schemes that can serve as a foundation for CO2 capture demonstration projects. By determining the optimal configuration, this research aims to pave the way for the successful implementation of efficient and economically viable CO2 capture technologies in the power generation sector.

Currently, one of the main focuses of attention in academia is microgrids (MGs) and their ability to maintain stable, resilient, reliable and high–power quality operations. A crucial component in MGs is power converters (PC), which facilitate the decentralization of power generation. This decentralization, however, poses challenges in terms of power quality. This paper presents a microgrid model based on the IEEE 14–bus distribution system and aims to investigate the power quality when the MG operates while connected to the conventional power grid. The MG model has been developed using MATLAB–Simulink®, a specialized tool for electrical engineering simulations. The results obtained are subjected to rigorous analysis and compared with the compatibility levels established by the IEEE–519 standard. This approach allows an accurate assessment of the MGs’ ability to maintain power quality at acceptable levels while interconnected to the conventional power grid. Finally, this study provides a valuable contribution to the MGs’ field of microgrids by providing a detailed and quantitative assessment of power quality, which will aid in the design and optimization of MGs’ for effective implementation in real electric power systems.

Improving performance and promoting sustainability in women's handball are key objectives to maximize the potential of female players and ensure the long-term viability of the sport. In this context, training with Olympic movements and their derivatives improves the development of strength, power, and speed, which are determinants of performance in team sports. The aim of this study was to determine if training with Olympic movements produces significant improvements in jumping, throwing, sprinting, and change of direction performance in women handball players. Twenty-one female handball players participated in the study (10 for the control group and 11 for the intervention group). Age ranged from 15 to 17 years. All participants performed four assessment tests (Abalakov Test, throw test, 20-meter Sprint and V-Cut Test) to determine jump height, throwing speed, running speed, and change of direction ability. Measurements were carried out before and after the intervention. For six weeks, the control group performed the strength work established by the club twice a week while the intervention group additionally performed training with Olympic movements. Significant differences (p &lt;0.05) were found between the pre and post measurement of the control group and the intervention group in jump height, throwing speed and running speed, being higher in the intervention group. For the change of direction, no significant differences were found. Between groups, significant differences were observed at the end of the intervention for jump height and running speed. The conclusion of this study was that, by training with Olympic movements, in addition to regular training, could produce greater improvements in jumping performance, throwing speed and running speed in female handball players.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

The design of highly efficient sensitizers is one of the most significant areas in dye-sensitized solar cell (DSSC) research. We have studied a series of benzothiadiazole-based D-π-π-A organic dyes, putting emphasis on the influence of the donor moiety on the DSSC’s efficiency. Using linear response time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional different donor groups were characterized in terms of electronic absorption spectra and key photovoltaic parameters. As a reference a dye has been considered which has a benzothiadiazole fragment linked via thiophene rings to a diphenylamine donor and a cyanoacrylic acid acceptor. The different systems are first studied in terms of individual performance parameters, which are eventually aggregated into the power conversion efficiency. Here only the amino-substituted species shows a modest increase, whereas the dimethylamino case even shows a decrease.

Power generation using renewable technologies has become a primordial option to satisfy the energy demand all over the world, being solar concentrating technologies widely applied for this purpose. A combination of Parabolic Trough Collector with Direct Steam Generation has been considered an excellent option for power generation, due to the economic cost and complexity in the plant are reduced. The thermal evaluation of the solar power plant as well as the PTC in the DSG process is very important in viability and economic analysis. In this sense, as the main objective of this work, a numerical tool for evaluating DSG with PTC technology has been developed. The software SOLEEC is a versatile, reliable, accurate and friendly to the user for thermally evaluating a DSG with PTC technology. The user has the possibility to compare the thermal behavior of different geometrical dimensions for a PTC; and even consider different materials; in order to satisfy the demand of superheated steam by a DSG process. The software has an error less than 5% when compared with literature results and in this paper is used to evaluate a power plant in Mexico obtaining that the change to DSG proposing different PTC could reduce the solar field about 35%.

The growing need to use renewable sources and the current difficulty in spreading the electricity grid in a widespread manner raise the question of how to respond to the need for more electricity immediately. The idea behind this study is to power a horizontal axis wind turbine with the air flow generated for cooling a stationary internal combustion engine. The power extracted from this solution is significantly lower than that of the internal combustion engine (about 0.3%) and could be advantageous only in limited contexts. Installation costs are limited because many elements deriving from wind variability can be removed or simplified.

This study analyzes the correlation between the lifetime and the rest energy of the unstable particle states with a lifetime greater than the zeptosecond (10⁻²¹ s), using data available from the Particle Data Group. This set of states seems to be divided into three groups, in each of which the two quantities can be correlated through a remarkably accurate power law. Although this fact does not represent anything new compared to the predictions of the Standard Model, it nevertheless reveals an unexpected order structure in the set of particle decays, emerging from such predictions.

We consider a control problem for a diffusive PDE model of heterogeneous population of thermostatically controlled loads (TCLs) aiming to balance the aggregate power consumption within a given amount of time. Using the Green’s function approach, the problem is formulated as an approximate controllability problem for a residue depending on control parameters nonlinearly. A sufficient condition for approximate controllability is derived in terms of initial temperature distribution, operation time of TCLs and threshold value of the aggregate power consumption. Case studies allow to reveal the advantages of the proposed solution from numerical calculations point of view.

Purposely slow velocity resistance exercise (i.e., 10 s concentric and eccentric phases) is a popular training method, but limits the loads that can be lifted (e.g., <50% 1 RM). This study compared the biomechanical properties of purposely slow velocity (SLOW) and traditional resistance exercise (TRAD) that uses maximal lifting velocities. Healthy resistance-trained men (n=5) performed two testing sessions (barbell squat and bench press) in random-order; a SLOW session (1 set x 10 repetitions at 28% 1 RM, 10 s concentric & eccentric), and a TRAD session (3 x 10 at 70% 1 RM, controlled eccentric and maximal concentric). A force plate and linear position transducer were used to collect kinetic and kinematic data for every repetition of both protocols (α = 0.05). For both exercises, both concentric and eccentric mean force (N) and power (W) for each repetition was greater for TRAD. When the entire training session (squat + bench press) was examined, SLOW exhibited greater time under tension, while TRAD produced greater work (J) and impulse (N·s). Contrary to suggestions in both the lay and scientific literature, purposely slow resistance exercise produced less force, power, and work than traditional velocity resistance exercise.

For the particular selected type of fractals, i.e., the Kronecker product based fractals, the introductory common classification is proposed. It essentially relies on the size and content of the initial fractal matrix. In turn, it gives one of the possible explanation of the phenomenal ability to produce a few of the most popular fractals using many different algorithms, languages and tools. Also, it paves the way to discover on the regular basis thousands of the new fractals, and this gives researchers a wider range of fractal models to choose from.

The process of water treatment by nanoparticles is one of the most considerable subjects in the cross-field of hydrodynamics, chemistry and mathematics. This paper is dedicated to the case of the flows that appear when squeezing and stretching a spongy with a mix of water with nanoparticles and contaminants. It is assumed that fluid is homogeneous at the starting moment, the parameters of the nanoparticles and contaminants are known, and there is a constant non-homogeneous magnetic field applied to the system. The flow starts moving when the walls of the channel shift to each other. Exact and numerical solutions of the system of ordinary differential equations are used to receive the results. The article gives an answer to the question about stability of the flow and proposes the technique to evaluate the essential characteristics of the system to achieve the treatment process efficiency. The main result is that the considered system shows excellent treatment properties during some part of squeezing stage. This effect does not appear without magnetic field.

In line with Pomeau’s conjecture about the relevance of directed percolation (DP) to turbulence onset/decay in wall-bounded flows, we propose a minimal stochastic model dedicated to the interpretation of the spatially intermittent regimes observed in channel flow before its return to laminar flow. Numerical simulations show that a regime with bands obliquely drifting in two stream-wise symmetrical directions bifurcates into an asymmetrical regime, before ultimately decaying to laminar flow. The model is expressed in terms of a probabilistic cellular automaton evolving von Neumann neighbourhoods with probabilities educed from a close examination of simulation results. It implements band propagation and the two main local processes: longitudinal splitting involving bands with the same orientation, and transversal splitting giving birth to a daughter band with orientation opposite to that of its mother. The ultimate decay stage observed to display one-dimensional DP properties in a two-dimensional geometry is interpreted as resulting from the irrelevance of lateral spreading in the single-orientation regime. The model also reproduces the bifurcation restoring the symmetry upon variation of the probability attached to transversal splitting, which opens the way to a study of the critical properties of that bifurcation, in analogy with thermodynamic phase transitions.

Fluid mechanics of flow in hydrophobic, rectangular microchannels with finite aspect ratios is of paramount importance. In such microchannels, not only the effect of the side walls should be taken into account, but also the classical assumption of no-slip boundary condition (BC) is no longer valid at the solid-liquid interface. Accordingly, slip flow can occur in microchannels fabricated from surfaces with low wetting conditions, hydrophobic surfaces. Determining the interactions of liquid molecules adjacent to solid surface is still a challenging issue, and it is especially important in small scale domains. Herein, the fluid mechanics of flow through rectangular hydrophobic microchannels has been reconsidered by taking into account the general Navier-slip BCs at the solid-liquid interface. For fully developed incompressible flow in microchannels at low Reynolds number, partial differential equation (PDE) of the momentum equation simplifies to the classical Poisson equation. Accordingly, by analytically solving the Poisson equations with general Navier-slip BCs, the most general forms of velocity distributions, flow rate, friction factor and Poiseuille number have been obtained.

Polymer flooding is one of the most successful chemical EOR methods, and is primarily implemented to accelerate oil production by sweep improvement. However, other benefits have extended the utility of polymers. During the last decade, it has been evaluated for an increasing number of fields, both offshore and onshore. This is a consequence of improved polymer properties, which extends the use to HTHS (high temperature high salinity) conditions and of improved understanding of flow mechanisms such as for heavy oil mobilization. A key issue in understanding polymer performance is to control and predict in-situ porous medium rheology. The first part of this paper reviews recent developments in understanding polymer flow in porous medium. Especially, polymer in-situ rheology and injectivity is discussed. The second part of this paper reports polymer flow experiments using the most applied polymer for EOR processes, HPAM (partially hydrolyzed polyacrylamide). The experiments address high rate near-wellbore behavior (radial flow) as well as reservoir rate steady state flow (linear flow) and discuss differences observed in terms of flow conditions. In addition, impact of oil on polymer rheology was investigated, and compared to single-phase polymer flow in Bentheimer sandstone rock material. Presence of oil leads to a reduction in apparent viscosity.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.

The environmental issues we are currently facing require long-term prospective efforts for sustainable growth. Renewable energy sources seem to be one of the most practical and efficient alternatives in this regard. Understanding a nation's pattern of energy use and renewable energy production is crucial for developing strategic plans. No previous study has been performed to explore the dynamics of power consumption with the change in renewable energy production on a country-wide scale. In contrast, a number of deep learning algorithms demonstrated acceptable performance while handling sequential data in the era of data-driven predictions. In this study, we developed a scheme to investigate and predict total power consumption and renewable energy production time series for eleven years of data using a Recurrent Neural Network (RNN). The dynamics of the interaction between the total annual power consumption and renewable energy production are investigated through extensive Exploratory Data Analysis (EDA) and a feature engineering framework. The performance of the model is found satisfactory through the comparison of the predicted data with the observed data, visualization of the distribution of the errors and Root Mean Squared Error (RMSE) value of 0.084. Higher performance is achieved through the increase in the number of epochs and hyperparameter tuning. The proposed framework can be used and transferred to investigate the trend of renewable energy production and power consumption and predict the future scenarios for different communities. Incorporation of the cloud-based platform into the proposed pipeline may lead to real-time forecasting.

Presently power control and management play a vigorous role in information technology and power management. Instead of non-renewable power manufacturing, renewable power manufacturing is preferred by every organization for controlling resource consumption, price reduction and efficient power management. Smart grid efficiently satisfies these requirements with the integration of machine learning algorithms. Machine learning algorithms are used in a smart grid for power requirement prediction, power distribution, failure identification etc. The proposed Random Forest-based smart grid system classifies the power grid into different zones like high and low power utilization. The power zones are divided into number of sub-zones and map to random forest branches. The sub-zone and branch mapping process used to identify the quantity of power utilized and the non-utilized in a zone. The non-utilized power quantity and location of power availabilities are identified and distributed the required quantity of power to the requester in a minimal response time and price. The priority power scheduling algorithm collect request from consumer and send the request to producer based on priority. The producer analysed the requester existing power utilization quantity and availability of power for scheduling the power distribution to the requester based on priority. The proposed Random Forest based sustainability and price optimization technique in smart grid experimental results are compared to existing machine learning techniques like SVM, KNN and NB. The proposed random forest-based identification technique identifies the exact location of the power availability, which takes minimal processing time and quick responses to the requestor. Additionally, the smart meter based smart grid technique identifies the faults in short time duration than the conventional energy management technique is also proven in the experimental results.

The work addresses the problem of Power Quality (PQ) metrics (or indexes) suitable for DC grids, encompassing Low and Medium Voltage applications, including electric transports, all-electric ships and aircrafts, electric vehicles, distributed generation and microgrids, modern data centers, etc. The two main pillars on which such PQ indexes are discussed and built are: i) the physical justification, so the electric phenomena affecting DC grids and components (PV panels, fuel cells, capacitors, batteries, etc.), causing e.g. stress of materials, ageing, distortion, grid instability; ii) the existing standardization framework, pointing out desirable coverage and extension, similarity with AC grids standards, but also inconsistencies. The first point is made more clear and usable by a graphical overview of the discussed phenomena. On this basis PQ is interpreted beyond the usual low-frequency range, including thus supraharmonics and common-mode disturbance, and filling the gap with the Electromagnetic Compatibility domain. However, phenomena typical of EMC and electrical safety (such as various types of overvoltages and fast transients) are excluded. Suitable PQ indexes are then reviewed, suggesting integrations and modifications, to cover the relevant phenomena and technological progress, and to better follow the normative exigencies.

The development of small scale hydroelectric power plants in Norway is determined by natural conditions, policies, attitudes and property rights. The owner of the river is the central decision maker. It is he who decides whether he will develop the power plant himself, Whether he wants to enter into a contract with an external investor and let him develop the power plant, whether he will sell his property rights or postpone the decisions. All available choices will involve risk. In order for him to make the best choice he must find the certainty equivalent to each of the choices and choose the one with the highest certainty equivalent. This is the first time the utility theory of John von Neumann and Oskar Morgenstern has been applied to decision makers in the hydro power industry in Norway.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

Differential diagnosis of solid pancreatic lesions (SPLs) using B-mode endoscopic ultrasonography (EUS) is challenging. Detective flow imaging (DFI) offers the potential for detecting low-flow vessels in the pancreas, thus enhancing diagnostic accuracy. This study aimed to investigate DFI-EUS findings of SPLs and analyze their differential diagnostic accuracy for pancreatic cancer. This retrospective study included patients with pathologically confirmed SPLs who underwent EUS between April 2021 and June 2023. Expert endosonographers, blinded to the patients’ clinical data, evaluated images obtained through B-mode, eFLOW, and DFI-EUS. Frame rate and vessel detection sensitivity between eFLOW and DFI were compared, and diagnostic criteria for pancreatic cancer were established. This study included 104 patients, most diagnosed with pancreatic cancer. DFI-EUS demonstrated a significantly higher vessel visualization rate (96%) in SPLs compared to eFLOW (27%). Additionally, DFI showed a superior frame rate, sensitivity (99%), and accuracy (88%) in detecting pancreatic cancer, although with a modest specificity (43%). On DFI-EUS, characteristics such as hypovascular, peritumoral, or spotty vessel findings were suggestive of pancreatic cancer. DFI-EUS significantly improved the visualization of vascular structures within the SPLs, highlighting its efficacy as a diagnostic modality for pancreatic cancer.

Several epidemiological studies and intervention trials have demonstrated that flavanols present in grapes and blueberries can lower the risk of cardiovascular disease. However, the mechanisms of action of these compounds remain unclear due to their low bioavailability. A polyphenol-rich grape and blueberry extract (PEGB) contained about 16% flavanol, of which 11% was monomer and 4% was dimer. A sensory test investigated the oral perception of a PEGB. At concentrations where quercetin had almost no detectable taste, PEGB exhibited significant astringency. Furthermore, in comparing the redox properties against O2･- using a luminescence method, PEGB acted as a prooxidant at low concentrations, promoting O2･-production and scavenging O2･-at high concentrations under pH conditions similar to oral cavity and intestine. In contrast, quercetin showed antioxidant activity at any concentration. A single oral administration of PEGB to rats showed a significant increase in skeletal muscle arteriolar blood flow. According to these results, PEGB containing flavanols displays a potent astringent flavor, increases O2･-production at low concentrations in a neutral pH environment as well as oral and intestine, and considerably enhances blood flow to skeletal muscles after a single dose in rats. The results of this study indicate a need to investigate the causal relationship between oral perception, redox properties, and bioactivity of polyphenols.

Flow experience, characterized by deep immersion and complete engagement in a task, is highly recognized for its positive psychological impacts. However, previous studies have been restricted to use a single type of task, and the exploration on its neural correlates has been limited. This study aimed to explore the neural correlates of flow experience with the employment of multifac-eted flow-induction tasks. Six tasks spanning mindfulness, artistic tasks, free recall, and varying levels of Tetris complexity (easy, flow, and hard conditions) were employed to have a relatively complete coverage of the known flow-induction tasks for a better induction of individualized flow experience. Twenty-eight participants were recruited to perform these six tasks, with a sin-gle-channel prefrontal electroencephalography (EEG) recording. Significant positive correlations were observed between the subjective flow scores of individual’s best-flow-experience task and the EEG activities at delta, gamma, and theta bands, peaking at latencies around 2 minutes after task onset. The outcomes of our multiple regression analysis yield a maximum coefficient of de-termination (R²) of 0.279. Our findings report the EEG correlates of flow experience in naturalistic settings and highlight the potential of portable and unobtrusive EEG technology for an objective measurement of flow experience.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

The influence of a background vortex flow on clustering of floating tracer is addressed. The vortex flow considered is induced by an ellipsoidal vortex evolving in a deformation. The system exhibits various vortex motion regimes: (i) steady state, (ii) oscillation and (iii) rotation of the ellipsoidal vortex core. The latter two induce unsteady velocity field for the tracer thus leading to irregular (chaotic) tracer motion. Superimposing a stochastic divergent velocity field onto the deterministic vortex flow allows us to observe significantly different tracer evolution. We use the method of characteristics to integrate the floating tracer density evolution equation and the Euler-Ito scheme for obtaining the floating tracer trajectories with the random velocity field. The cluster area and cluster mass from the statistical topography were used as the quantitative diagnostics of floating-tracer’s clustering. For the case of the steady ellipsoidal vortex embedded into the deformation flow with a random velocity field component we found that clustering characteristics are weakened by the steady vortex. For the cases of an unsteady ellipsoidal vortex, we observed clustering in the floating-tracer density field if the contribution of the divergent component is higher or equal to that of the rotational (nondivergent) component. Even when the initial floating tracer patch was set on the boundary of oscillating ellipsoidal vortex, we observed formation of clusters. In the case of a rotating ellipsoidal vortex, we also observed pronounced clustering. Thus, we argue that unsteady ellipsoidal vortex regimes (oscillation and rotation), which induce chaotic motion of the nearby passive tracer’s trajectories, are still conducive to clustering of floating tracer observed in the density field despite the intense deformation introduced by strain and shear.

Aim at a better understanding of the flow field around a fully appended Joubert BB2 submarine model and complementing the experimental investigations of the wake of the hydroplanes and sail, the Large eddy simulation (LES) with the dynamic Smagorinsky model is conducted. Three sets of grids with a maximum grid number of up to 228 million are designed, to perform the LES simulation for the Joubert BB2 at 10° yaw conditions, with a freestream Reynolds (Re) number based on the local freestream velocity and the hull length of ReL=2.2×107. And comparison of the wake of the cruciform appendage is made with experiments, to verify the computational accuracy and examine the influence of the spatial resolution. A satisfactory result shows more favorable agreement with experimental measurements as the improvement of spatial resolution, with the relative error of the vortice centers well within 7.2% in the most refined grid arrangement. And under this grid arrangement, the evolution characteristics of three co-rotating vortices originating from the cruciform appendage are further described in detail at straight ahead and 10° yaw conditions.

An aneurysm is a vascular malformation, it can be classified according to its location (cerebral, aortic); and according its shape (saccular, fusiform, and mycotic). The study of blood flow interaction with the aneurysms has gained attention from physicists an engineers in recent years. Shear stresses, oscillatory shear index (OSI), gradient oscillatory number (GON), and residence time had been used as potential variables to describe the hemodynamics as well as the origin and evolution of aneurysm. However, the causes of aneurysms and the hemodynamics conditions that promote the growth of these structures are still under debate. The present work presents numerical simulation on three aneurysms: 2 aortic and 1 cerebral. The results shows that the blood rheology is not relevant for aortic aneurysms, however, for cerebral aneurysm could play a relevant role in the hemodynamics. The turbulence models evaluated show equivalent results in both cases. Lastly, a simulation considering the fluid-structure interaction (FSI) shows that this phenomenon is the dominant factor for aneurysms simulation.

Rapid, accurate, and convenient diagnosis is essential for effective disease management. Various detection methods, such as enzyme-linked immunosorbent assay, have been extensively used, with lateral flow immunoassay (LFIA) recently emerging as a major diagnostic tool. Nanoparticles (NPs) with characteristic optical properties are used as probes for LFIA, and researchers have presented various types of optical NPs with modified optical properties. Herein, we review literature on LFIA with optical NPs for the detection of specific targets in the context of diagnostics.

Mass transfer is often the rate determining step for solid-liquid chemical reactions. Decrease of the concentration boundary layer thickness is essential to intensify the chemical reaction. Because the concentration boundary layer exists in the velocity boundary layer, force imposition in the concentration boundary layer by superimposing an electrical current and a magnetic field was proposed. Through, flow can be directly excited in the concentration boundary layer. The previous result indicates that by superimposing a DC current and a gradient magnetic field, the development of the concentration boundary layer was suppressed, because of a macro-scale flow excitation in the whole vessel. And by superimposing the gradient magnetic field with a modulate current, the development of the concentration boundary layer was further suppressed. This is because of the macro-scale flow enhancement and the excitation of a micro-scale flow near the solid-liquid interface. However, the mechanism for the micro-scale flow excitation has not been clarified. To clarify this, a uniform magnetic field was superimposed with the DC current or the modulate current. By this means, only the micro-scale flow was excited near the anode surface. The results found that the non-unform electromagnetic force distribution is the main reason for the micro-scale flow excitation.

The purpose of this paper is to study the sliding mode control as a Ricci flow process in the context of a three-story building structure subjected to seismic waves. The stability conditions result from two Lyapunov- functions, the first associated with slipping in a finite period of time, and the second with convergence of trajectories to the desired state. Simulation results show that the Ricci flow control leads to the minimization of the displacements of the floors. 3D Ricci solitons projection via a semi-conformal mapping to a surface is also studied.

Herpesviruses produce a plethora of pleomorphic and heterogeneous particle populations. The composition and biological role of these is not understood. Detailed analysis has been challenging due to the lack of multidimensional identification and purification methodologies. Fluorescence-activated cell sorting (FACS), originally developed to sort objects with at least ten thousand-fold larger volumes, has recently been applied to cellular exosomes as well as viral particles and has been dubbed nanoscale flow cytometry or “flow virometry”. In comparison to other nanoparticles, herpesvirus concentrations can be measured with high precision using simple culturing methods. Here, we used this unique capability to evaluate a standard FACS sorter. We demonstrate that detection and separation capabilities were insufficient to distinguish infectious fluorescent viral populations from populations lacking fluorescence and infectivity. Moreover, fluorescent populations did not contain single virus particles but mostly aggregates. On top, analysis of viral samples by flow cytometry was confounded by swarm detection, as multiple objects are measured simultaneously and interpreted as a single object. Despite these technical difficulties, comparison of crude supernatant to gradient purified HCMV revealed that infectious virus is a minor proportion of the particles released from infected cells. Our data stress the need for a set of standardized controls and protocols when applying FACS to biological nanoparticles and highlights technical challenges that need to be solved before flow virometry can achieve its full potential.

In this paper, a further mathematical analysis of some previous results of the author’s ongoing investigation regarding Prandtl’s equations is accomplished. In particular, the objective of the present work is the performance of an approximate explicit solution to Prandtl’s system of equations for a laminar, isothermal, incompressible and steady boundary layer flow of a Newtonian fluid, over an infinite horizontal flat plate.

Pollution of sub-surface water reservoirs mainly rivers and streams through contaminated water point sources (CWPS) was studied. The objective was to formulate a discrete time delay mathematical model which describes the dynamics of reservoir pollution using mixing-problem processes that involve single species contaminants such as nitrates, phosphorous and detergents. The concentration of pollutants was expressed as a function of the inflow and outflow rates using the principle for the conservation of mass. Systems of ODEs generated from principles of mixing problems were refined into a system of DDEs so that the concentration of pollutant leaving the reservoir at time would be determined at some earlier instant, for the delay. The formulated model is a mathematical discrete time delay model which would be used to describe the dynamics of sub-surface water reservoir pollution. The results from the validation of the model were analyzed to determine how time delays in the mixing processes affect the rate of particle movement in water reservoirs.

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

Using a randomized, crossover approach, cyclists (N = 20, overnight fasted) engaged in three 75-km time trials while ingesting water (WAT) or carbohydrate (0.2 g/kg every 15 minutes) from bananas (BAN) or a 6% sugar beverage (SUG). Blood samples were collected pre-exercise and 0 h-, 1.5 h-, and 21 h-post-exercise, and analyzed for NK cytotoxicity activity (NKCA) using pure NK cell populations. The two carbohydrate trials (BAN, SUG) compared to WAT were associated with higher post-exercise glucose, and lower cortisol, total blood leukocyte, neutrophil, and NK cell counts (interaction effects, P < 0.001). The immediate post-exercise increase in NK cell counts was higher in WAT (78%) compared to BAN (32%) and SUG (15%) trials (P ≤ 0.017). The 1.5 h post-exercise decrease in NK cell counts did not differ after WAT (−46%), BAN (−46%), and SUG (−51%) trials. The pattern of change in post-exercise NKCA differed between trials (P < 0.001). The 1.5 h post-exercise decreases in NKCA were 23%, 29%, and 33% in the WAT, BAN, and SUG trials, respectively, but trial contrasts did not differ significantly. Carbohydrate ingestion from BAN or SUG attenuated immediate-post-exercise increases in leukocyte, neutrophil, and NK cell counts, but did not counter the 1.5-h decreases in NK cell counts and NKCA.

The presence of wireless communication grows undeniably more prevalent each year. Since the introduction of the IEEE 802.11 standard for Wireless Local Area Networks (WLAN) in 1997, technologies have progressed to provide wireless accessibility to industries and consumers with growing ease and convenience. As the usage of personal devices, such as phones and watches, that connect to the Internet through Wi-Fi increases, wireless attacks on users are becoming more critical. This paper provides a novel attack model to offer an organized and comprehensive view of the possible attacks on WiFi latest security standards. All exiting attacks will be investigated, with emphasis on more recent attacks, such as the KRACK and PMKID Dictionary attacks. This paper will then analyze the technology offered in the new Wi-Fi Protected Access III (WPA3) security scheme and provide a comprehensive security analysis and discussion to determine whether it has addressed the vulnerabilities of its predecessor. An interesting finding of this paper is that WPA3 still lacks to address all the issues existed in WPA2 and explore other mitigations for future research.

Accent is on determination of appropriate friction factor of the pipes and on selection of the representative equation for water or natural gas flow which is valuable for existing conditions in the looped network of pipelines. Note that in a municipal gas pipeline, natural gas can be treated as incompressible fluid (liquid) i.e. as water or oil. Even under this circumstance, calculation of water pipelines cannot be literary copied and applied for calculation of gas pipelines. Inappropriate friction factor, equally as e.g. inappropriate usage of water flow equations for calculation of gas networks can lead to inaccurate final results. Few iterative methods for determining the optimal hydraulic solution of water- and gas- looped pipeline networks, such as, Hardy Cross, modified Hardy Cross, node-loop method, node and M.M. Andrijashev method, will be shown. Speed of convergence will be compared and discussed using a simple network with three loops.

Laser Cladding is one of the leading processes within Additive Manufacturing technologies, a fact which has concentrated an important amount of effort on its development. In regard to the latter, the current study aims to summarize the influence of the most relevant process parameters in the laser cladding processing of single and compound volumes (solid forms) made from AISI 316L stainless steel powders and using a coaxial nozzle for deposition. Process speed, applied laser power and powder flow are considered to be the main variables affecting laser cladding in single clads, meanwhile overlap percentage and overlapping strategy become also relevant when dealing with multiple clads. By means of setting appropriate values of each process parameter, the main goal of this paper is to develop a processing window in which a good metallurgical bond between the delivered powder and substrate is obtained, trying simultaneously to maintain processing times in their lowest value possible. Conventional metallography techniques were performed on the cross sections of the laser tracks to measure the effective dimensions of clads for dilution analysis, height and width for the values of overlap between contiguous clads and layers, and also to analyze them for physical defects such as porosity and cracks. The resulting solid piece was 8 mm high at 800 mm/min.

Abstract: In this study the semi-distributed model SWAT (Soil and Water Assessment Tool), were applied to evaluate stream flow of Didessa sub basin, which is one of the major sub basins in Abay river basin of Ethiopia. The study evaluated the quality of observed meteorological and hydrological data, established SWAT hydrological model, identified the most sensitive parameters, evaluated the best distribution for flow and developed peak flow for major tributary in the sub basin. The result indicated that the SWAT model developed for the sub basin evaluated at multi hydro-gauging stations and its performance certain with the statistical measures, coefficient about determination (R2) and also Nash coefficient (NS) with values ranging 0.62 to 0.8 and 0.6 to 0.8 respectively at daily time scale. The values of R2 and NS increases at monthly time scale and found ranging 0.75 to 0.92 and 0.71 to 0.91 respectively. Sensitivity analysis is performed to identify parameters those were most sensitive for the sub basin. CN2, GWQMN, CH_K, ALPHA_BNK and LAT_TIME are the most sensitive parameters in the sub basin. Finally, the peak flow for 2-10000 returns periods were determined after the best probability distribution is identified in EasyFit computer program.

In this study, deep neural network (DNN) and transfer learning (TL) techniques were employed to predict the viscous resistance and wake distribution based on the positions of flow control fins (FCFs) applied to containerships of various sizes. Both methods utilized data collected through Computational Fluid Dynamics (CFD) analysis. The position of the flow control fin (FCF) and hull-form information were utilized as input data, and the output data included viscous resistance coefficients and components of propeller axial velocity. The base DNN model was trained and validated using a source dataset from a 1000 TEU containership. Grid search cross-validation technique was employed to optimize the hyperparameters of the base DNN model. Then, transfer learning was applied to predict the viscous resistance and wake distribution for containerships of varying sizes. To enhance the accuracy of feature prediction with a limited amount of dataset, learning rate optimization was conducted. Transfer learning involves retraining and reconfiguring the base DNN model, and the accuracy was verified based on the fine-tuning method of the learning model. The results of this study can provide hull designers for containerships with performance evaluation information by predicting wake distribution, without relying on CFD analysis.

The pore-throat radius of shale oil reservoir is extremely small, and it is difficult to accurately obtain the absolute permeability and oil-water two-phase relative permeability of actual oil reservoir through conventional core experiments. However, these parameters are very important for reservoir numerical simulation. In this paper, a method for characterizing flow parameters based on pore network model that considers differential pressure flow and diffusion flow is proposed. Firstly, a digital core was reconstructed using focused ion beam scanning electron microscopy (FIB-SEM) from the Gulong shale reservoir in the Songliao Basin, China, and a pore network model was extracted. Secondly, quasi-static single-phase flow and two-phase flow equations considering diffusion were established in the pore network model. Finally, pore throat parameters, absolute permeability, and oil-water two-phase permeability curves were calculated, respectively. The results show that the pore throat distribution of Gulong shale reservoir is mainly concentrated in the nanometer scale, the mean pore radius is 87 nm, the mean throat radius is 41 nm, and the mean coordination number is 3.97; The calculated permeability considering diffusion is 0.000124mD, which is approximately twice the permeability calculated without considering diffusion; The irreducible water saturation of the Gulong shale reservoir is approximately 0.26, and the residual oil saturation is approximately 0.73. The method proposed in this paper can provide an important approach for characterizing the flow parameters of similar shale oil reservoirs.

The eighty years old empirical Colebrook function widely used as an informal standard for hydraulic resistance relates implicitly the unknown flow friction factor , with the known Reynolds number and the known relative roughness of a pipe inner surface ; . It is based on logarithmic law in the form that captures the unknown flow friction factor in a way from which it cannot be extracted analytically. As an alternative to the explicit approximations or to the iterative procedures that require at least a few evaluations of computationally expensive logarithmic function or non-integer powers, this paper offers an accurate and computationally cheap iterative algorithm based on Padé polynomials with only one -call in total for the whole procedure (expensive -calls are substituted with Padé polynomials in each iteration with the exception of the first). The proposed modification is computationally less demanding compared with the standard approaches of engineering practice, but does not influence the accuracy or the number of iterations required to reach the final balanced solution.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

This paper studies a multihop amplify-and-forward (AF) simultaneous wireless information and power transfer (SWIPT) relaying system. Each relaying node harvests energy using power splitting (PS) scheme from a part of its received signal to amplify and forward the rest the received signal to the next relay. Based on this system model and signal flow, we derived and solved the convex energy minimization problem with optimal PS ratio. The influence of processing cost was then investigated for the AF-SWIPT system with the decode-and-forward SWIPT as benchmark, where AF-SWIPT was found to be superior.

Power converter technologies have become increasingly vital in various applications due to their efficient management of electrical energy. With the growing prominence of renewable energy sources like solar and wind, the high penetration of power electronic converters has been justified. However, ensuring power quality has emerged as a significant challenge for grid-connected power converters. The divergence from the ideal sinusoidal waveform in terms of magnitude and frequency impacts both grid-side currents and voltages. Several studies have proposed solutions to address power quality issues at the load side. The advancement of power converters has been fueled by the development of high-performance microprocessors and the emergence of high-speed switching devices, such as SiC-MOSFETs. This paper focuses on the design of voltage source converters, particularly those based on SiC-MOSFET semiconductor devices. The article presents the design of H-Bridge cells, discusses two-level voltage source converters based on cascade H-Bridge cells in parallel configuration with experimental fault analysis, addresses the seven-level voltage source converters topology, and explores the design and experimental results of the matrix converter. The findings underscore the importance of considering the entire converter design for improved performance at high switching frequencies. The article concludes by summarizing the main outcomes and implications of this research.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

This work investigates how to balance the electricity supply and demand in a carbon-neutral northern Europe. Applying a cost-minimizing electricity system model including options to invest in eleven different flexibility measures, cost-efficient combinations of strategies to manage varia-tions are identified. The results of the model are post-processed using a novel method to map the net load before and after flexibility measures are applied to reveal the contribution of each flexi-bility measure. The net load is mapped in the space spanned by the amplitude, duration, and number of occur-rences. The mapping shows that, depending on cost structure, flexibility measures contribute to reduce the net load in three different ways; 1) by reducing variations of long duration but low amplitude, 2) by reducing variations of high amplitude but short duration and low occurrence or 3) by reducing variations of high amplitude, short duration and high occurrence. It is found that cost-efficient variation management is achieved by combining wind and solar power and by combining strategies (1-3) to manage variations. The cost-efficient combination of strategies de-pends on electricity system context where electricity trade, flexible hydrogen and heat production (1) manage the majority of variations in regions with good conditions for wind power while sta-tionary batteries (3) are the main contributors in regions with good conditions for solar power.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

High-penetration of Distributed Energy Resources (DER) in low voltage distribution grids, mainly photovoltaics (PV), might lead to overvoltage in the point of common coupling. Volt-VAr is one of the common control functions for DER power converters used to enhance the stability and the reliability of the voltage in the distribution system and, thus, fulfilling the network operator requirements. In this study, a centralized algorithm will provide local Volt-VAr control parameters to each PV inverter, based on the electrical grid characteristics where each equipment is installed. Since accurate information of grid characteristics is typically not available, the parametrization of the electrical grid is done using power meter data in DER location and a voltage sensitivity matrix. The algorithm has different optimization modes to both minimize voltage deviation and line current. In order to validate the effectiveness of the algorithm and its deployment in real infrastructure, it has been tested in an experimental setup with PV emulators in a set of 5-day tests. Volt-VAr control algorithm successfully adapted its parameters based on grid topology and PV inverter characteristics, achieving a voltage reduction up to 25% of the allowed voltage deviation.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

The Review examines studies aimed at the organization of energy (non-mechanical) control of high-speed flow/flight using spatially multi-component plasma structures and combined energy deposition. The Review covers selected works on experimental obtaining and numerical modeling multi-component plasma structures and use of sets of actuators based on the plasma of such a spatially type for the purposes of control of shock wave/bow shock wave – energy source interaction, as well as control of shock wave – boundary layer interaction. A series of works on repetitive multiple laser pulse plasma structures is also analyzed from the point of view of examining shock wave/bow shock wave boundary layer interaction. Self-sustained theoretical models for laser dual-pulse, multi-mode laser pulses and self-sustained glow discharge are also considered. Separate sections are devoted to high-speed flow control using combined physical phenomena and numerical prediction of flow control possibilities using thermal longitudinally layered plasma structures. The wide possibilities for organization and applying spatially multi-component structured plasma for the purposes of high-speed flow control are demonstrated.

Most existing coal-fired power plants were designed for sustained operation at full load to maximize efficiency, reliability, and revenue, as well as to operate air pollution control devices at design conditions. Depending on plant type and design, these plants can adjust output within a fixed range in response to the plant operating or market conditions. The need for flexibility driven by increased penetration of variable and non-dispatchable power generation such as wind and solar is shifting the traditional mission profile of thermoelectric power plants in three ways: more frequent shutdowns when market or grid conditions warrant, more aggressive load ramp rates (rate of output change), and lower minimum sustainable load, which provides a wider operating range and helps avoid costly plant shutdowns. Recent studies have shown that flexibility of a coal-fired power plant can be improved by energy storage. The objective of this work was to analyze a set of energy storage options and determine their impact on flexibility and economics of a representative coal-fired power plant. The effect of three energy storage systems integrated with a coal power plant on plant flexibility and economics was investigated. The results obtained in this project show that Energy Storage Systems integrated with a thermal power plant improves plant flexibility and participation in the Energy and Ancillary Services markets which improves plant financial performance. The study was funded by the U.S. Department Office of Fossil Energy FE-1 under Award Number DE-FE0031903.

This paper aims to explore how climate change affects electricity generation (fossil-fueled power plants, hydroelectric stations, wind systems and photovoltaics) and energy demand in residential buildings in Greece for the period up to 2050. In both cases RCP scenarios results are considered in the appropriate spatial and temporal dimension. Energy supply technologies were examined through statistical regression models and/or mathematical equations correlating climatic parameters with energy productivity. With respect to energy demand, bottom-up models were developed that integrate behavioral and policy aspects. The analysis showed that climate change is expected to mainly affect electricity generation from hydro and thermal power plants, while the impacts on solar and wind energy are significantly lower. The range of impacts on hydro potential and electricity generation depends on the geographical location of the power plants and shows significant uncertainty due to the corresponding uncertainty in climate models estimates regarding precipitation and runoff changes while showing significant geographical variations. With respect to energy demand, climate change is expected to affect energy consumption, but the expected range of effects depends on both the implementation and the characteristics (deep vs. shallow renovation) of measures for upgrading the thermal performance of the building stock and the intensity of climate change.

Contactless charging is evolving fast in many domains and applications such as the electrical vehicles (EV). The principle consists of transferring energy between two systems without having any electrical connection between them. This power transfer can be realized by emitting a magnetic field for Inductive Power Transfer (IPT). In the automotive domain, the application of contactless charging to supply power to the vehicle while driving is one of the solutions envisaged to solve the limited autonomy range of EV and reduced its cost but the system must comply with existing standards (e.g., allocated frequency range and radiated electromagnetic emissions), as summarized in this paper.

The world population increased from 1 billion in 1800 to around 8 billion today. The Population Division of the United Nations predicts a global population of approximately 10.4 billion people by the end of the century. That represents over 2 billion more people. Moreover, the global community is currently experiencing a precarious state due to the enduring repercussions of the COVID-19 pandemic across all sectors, including energy. Given the rising global population and the limited availability of primary energy resources, we must reach a balance between the demands of a growing human population and the planet’s carrying capacity. The dreadful conflict in Ukraine has precipitated an enormous energy crisis. This crisis served as a warning to the world population of how much they depend on this resource to survive. In France, building sectors (i.e., residential and tertiary) alone consume 45% of the final energy disposable. It is the first energy consumer of the country and one of the most polluting (i.e.; about 34% of CO2 emitted by France). Consequently, we must consider alternative energy resource forms (i.e.; substitution energy forms). Harvesting energy from the building envelope may be a viable technique for partially satisfying the electricity demands of building users. In this context, scientific research offers considerable potential for developing more innovative and efficient systems. This article aims to review the state of the art of advances on the subject to orient and further optimize energy production systems, particularly electricity. This work will address several points of view: Discusses the overall backdrop of the present study and introduces the subject ; details the research strategy and procedures used to produce this paper ; develops state of the art on the potential for generating or recovering power from the building envelope ; presents the SWOT analysis of the earlier-described systems. And finally, it concludes by offering findings and viewpoints.

This policy paper explores various strategies that would facilitate transitioning the traditional Jordanian electrical grid to a secure smart grid. It includes comprehensive recommendations from academia and industry for the regulatory and governmental sector in Jordan to achieve specific roadmap objectives. As Jordan is heavily dependent on fossil fuels, This policy paper also provides recommendations for incorporating more renewables into its energy mix, thereby facilitating a sustainable future. The proposed policies will emphasise the creation of an enabling environment where innovation, research, and development initiatives flourish, thereby promoting private sector engagement.

The fluctuation of the conditions on Lake Limboto affects people's activities around the lake. They try to survive by facing the problem of the lake, which is shallowing and narrowing. Yet the lake is predicted will be disappeared in 2030. This means that the productivity of the lake also diminishes. This article aims to analyze how the communities around the lake respond to the evolution and shocking prediction toward the lake into their daily activities. This study uses an interdisciplinary approach by integrating some fields of study to understand and solve the problems. One of the approaches involves interviewing people around the lake. Nevertheless, the base of the study is socio-cultural studies, which uses also old texts and oral literature as the support of the study. The research needs the theory of cultural studies to look at the survival and resilience of the people of lake so that they form their special daily activity. The results of the study show that some people know that there is a prediction of disappearing of the lake, but they have not anticipated it, as if this problem is only a government affair. They still live at the lake bank, try to survive and to be resilience even in poor conditions.

Synchronization is a prerequisite for the stability of electrical energy, which is the cornerstone of a functioning society. Identifying whether generators are synchronized or not has been attracting immense research interest. Utilizing synchronized stability boundaries can strongly simplify stability discrimination. However, fundamental issues such as determining accurate stability boundaries remain challenging. In this study, an accurate synchronized stability boundary equation that is independent of the system and disturbances is presented, and it is applicable to an arbitrarily coupled grid. The special structure induced by spontaneous synchronization appears to be only near the stability boundary. The results of this study show that: the synchronous stability boundary is an intrinsic property of the system, independent of its structure and parameters. Synchronization on the network may be independent of the network. These conclusions will challenge the traditional perception of synchronization on networks, and the synchronization stability of the grid can be analyzed in a uniform way.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.