Antibiotic-loaded bone cements are widely used in orthopedic surgery. However, they present issues such as a short antibiotic release time and the antibiotic resistance. These challenges necessitate the development of novel antibacterial bone cements. Non-leaching bone cement containing antibacterial motifs represents a promising advancement in this direction. Antibacterial motifs are incorporated into the cement either covalently or non-covalently, and while they will not be released, they will still exhibit surface antibacterial activity. This review comprehensively examines the structure and antimicrobial activity of prevalent non-leaching antimicrobial bone cements. Additionally, it delves into the characteristics of current methods employed for detecting surface antimicrobial activity. Finally, the future research direction of non-leaching antibacterial bone cement is discussed, with a specific focus on innovative antibacterial motifs, the mechanisms underlying non-leaching antibacterial properties, and the potential synergies achievable by combining non-leaching antibacterial bone cement with traditional antibiotics.

The research on calcium leaching of 3D printed cement pastes (3DPC) exposed in aggressive water is limited, and the mechanism underlying its effect needs to be better understood. The performance anisotropy of degraded 3DPC due to calcium leaching is investigated in this paper. Samples with aggregate micro fines (AMF) and fly ash (FA) were prepared. A 6 mol/L NH₄Cl solution was used in the accelerated experiment. At specific leaching durations, performances were tested on the samples in different leaching directions. Results show that the performances of 3DPC in aggressive water have a significant anisotropic behavior. The evolution of pore defects and hydration products mainly governs the performance anisotropy of degraded 3DPC. The remaining hydration products of the surface of 3DPC leached in the Z direction are less than the other two directions because calcium ions leached in the Z direction are difficult to be compensated through weak interfaces between layers.

This paper focused on the oxidative leaching process of vanadium from vanadium-chromium reducing residue in alkaline medium with MnO₂. The effect of experimental parameters including reaction time, reaction temperature, dosage of MnO₂, dosage of NaOH, and liquid-to-solid ratio on the leaching efficiency of vanadium had been studied. The results indicated that MnO₂ was an efficient oxidant for leaching out of vanadium. The leaching efficiency of vanadium was up to 97.25% under optimal reaction conditions: reaction temperature of 90 ℃, reaction time of 60 min, dosage of MnO₂ at 50 wt.%, concentration of NaOH at 30 wt.% and liquid-to-solid at 5:1 mL/g.

An integrated two-stage metallurgical technology has been developed for processing concentrates from the Olimpiadinskoe deposit with high antimony and arsenic content. The parameters of the alkaline sulphide leaching process of the initial concentrate of the Olimpiadinskoe deposit, providing maximum extraction of antimony in solution at 99% level have been recommended. The L:S ratio = 4,5:1; the concentration of sodium sulphide - 61 g/L; the concentration of sodium-hydroxide – 6,5 g/L; the duration – 3 hours; the temperature – 50 °C. A synergistic effect of alkaline sulphide leach cakes co-processing by sulphuric and nitric acids has been determined. Pre-treatment allows to reduce the composition of nitric acid by converting the carbonates into gypsum and increases the extraction of arsenic by 15 % at the following nitric leaching. Laboratory research of nitric acid leaching of decarbonized cake allowed to set the basic parameters for maximum iron and arsenic extraction in solution (92 and 98 %): the L:S ratio =9:1; the concentration of nitric acid – 6 mol/L; the time – 90 min. The full polynomial equations for iron and arsenic extraction from decarbonised cake have been derived. The model is relevant since the value the determination coefficients for iron and arsenic R2 were 96,7 and 93,2 %. The high value of gold recovery from the cake of two-stage alkaline sulphide and nitric acid leach cake at 95 % has been established. The maximum value of arsenic deposition from the nitrate leach solution in the form of the insoluble deposition As2S3 99,9 %. A basic technological flowsheet diagram for flotation gold-antimony processing for the Olimpiadinskoe deposit has been developed; it includes two redistributions: production of metallic antimony and gold extraction from the nitric leach cake.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH5N3S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH5N3S ⋅ m-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

Rock salt is characterized by specific geomechanical and rheological properties. Layers of rock salt on depth over 900 m cause problems with shaft lining deformation. Methods of shaft lining protection used so far (e.g. in Sieroszowice mine) have not been effective enough. The research presents a patented and copyright protected concept of a shaft lining construction that can be used in rock masses with strong rheological properties and susceptible to leaching. In the case of salt layers, especially at significant depths the relative convergence of the heading contour may be about 40 ‰/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, is not sufficient to ensure the stability of the shaft guidance geometry. In the new shaft lining concept, the excessive rock creep into the outbreak inside the shaft diameter is removed by local and controlled leaching of the shaft cheeks by means of fresh water through a porous medium at the contact layer behind the watertight tubing lining. The article presents the methodology of performing tests on a special device and the test results.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH₅N₃S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH₅N₃S × m^-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol^-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

The pre-emergent herbicide indaziflam is efficient in the management of weeds in eucalyptus crops, but this plant may develop less in soil contaminated with it. The objective was to evaluate the levels of chlorophylls a and b, the apparent electron transport rate (ETR), growth and dry matter of leaves, stems and roots of Clone I144, in clayey soil, contaminated with the herbicide indaziflam and the leaching potential of this herbicide. The design was completely randomized in a 3 x 5 factorial scheme, with four replications. Chlorophyll a and b contents, apparent electron transport rate (ETR), height growth and dry matter of leaves, stems and roots of Clone I144 were evaluated. The leaching of indaziflam in the clayey soil profile (69% clay) was evaluated in a bioassay with Sorghum bicolor, a plant with high sensitivity to this herbicide. The visual intoxication and height of this plant were evaluated at 28 days after sowing (DAS). Chlorophyll a and b contents and ETR, height and stem dry matter of Clone I144 were lower in soil contaminated with indaziflam residues. The dose of indaziflam, necessary to cause 50% (C50) of intoxication and the lowest height of sorghum plants, was 4.65 and 1.71 g ha-1 and 0.40 and 0.27 g ha-1 in clayey soil and sand, respectively. The sorption ratio (SR) of this herbicide was 10.65 in clayey soil. The herbicide indaziflam leached up to 30 cm depth at doses of 37.5 and 75 g ha-1 and its residue in the soil reduced the levels of chlorophylls a and b, the apparent electron transport rate (ETR) and the growth of Clone I144.

Bauxite residue (BR) is a well promising resource for critical metals and especially scandium (Sc), a rare and expensive metal with increasing applications in advanced technology. Particularly, Greek BR’s composition indicates a sound possibility for a commercially viable recovery of Sc under the conditions of an optimized leaching process and the subsequent use of advanced separation techniques. Leaching with mineral acids emerges as the dominant selection with comparison to other techniques. This study investigates an optimized leaching condition set on Sc recovery, using sulfuric acid as the most suitable among different acids tested, in the context of process economics and environmental constraints. Several variables were studied individually or combined in order to achieve high Sc concentration in the leachate as well as to ensure selectivity, especially in respect to iron. The most significant parameters proved to be the solid to liquid ratio (S/L), the final pH value as well as the use of recycling of leachate on fresh BR batches. The proposed process, using sulfuric acid at low acid molarities under ambient conditions was integrated rapidly leading to high and selective Sc recovery. A flow diagram of the developed leaching process in industrial scale was proposed based on continuous operation.

In Ecuador, particularly in the El Oro province, gold mining has been historically hampered by arsenic contamination in the ores. This research addresses the persistent issue of arsenic in gold-bearing ores from Miraflores Mine in Cerro Azul, Atahualpa Canton, and the challenges it presents to mining operations. The study's purpose is to evaluate the effectiveness of an alkaline leaching process for arsenic removal. The ore underwent thorough characterisation, employing advanced techniques like fire assay and atomic absorption. Once the ore's nature was discerned, an arsenic extraction experiment using a leaching solution was conducted. The implemented process achieved an arsenic removal efficiency of 90.54%. This enhanced ore quality facilitates efficient metallurgical applications and, more notably, reduces the environmental footprint by diminishing the need for harmful reagents like sodium cyanide. However, a significant implication of this method is the added cost due to the need for heat during the leaching test, amounting to an approximate $30 per ton increase. The alkaline leaching process emerges as a promising solution for arsenic challenges in El Oro’s mining sector. While the findings are encouraging, further expansive tests are recommended to validate the results and underscore the urgency for sustainable and hazard-conscious mining practices.

Abstract: The migration and transformation of pesticides in the environment will have an impact on the ecosystem. This study collected greenhouse soil from Shouguang, Shandong Province, and studied the photodegradation and leaching of 17 common pesticides in the soil. The results of photodegradation experiments showed that the degradation rate of certain pesticides was increased in the light environment, compared with that in the dark controls. The light half-lives of emamectin benzoate, pyraclostrobin, and metalaxyl were all shorter than their respective dark half-lives, indicating that their residues in soil were greatly affected by light. The leaching experiment showed that the leaching potential of the leachable pesticides was: nitenpyram ≫ metalaxyl > acetamiprid > carbendazim > diethofencarb ≈ chlorantraniliprole > isoprothiolane > oxadixyl > boscalid ≈ tebuconazole > hexaconazole. Pesticides that are easy to leach but not easy to degrade, such as chlorantraniliprole and metalaxyl, have a high potential risk of groundwater pollution, and more degradation technologies should be used to reduce their pollution risk. The study on photodegradation and vertical migration behavior of various pesticides in this study was conducive to providing references for the agricultural use and pollution control of pesticides.

Chemical weed control using herbicide glyphosate to manage emerged weeds is an important production practice in Florida citrus. Despite the extensive use of glyphosate in citrus orchards, very limited information is available on its environmental fate and behavior in Florida soils that are predominantly sandy in nature. Hence, the study's objective was to understand the adsorption-desorption, dissipation dynamics, and vertical movement or leaching of glyphosate in sandy soils in citrus orchards. Laboratory, field, and greenhouse experiments were conducted at Southwest Florida Research and Education Center in Immokalee, Florida. The adsorption-desorption behavior of glyphosate in the soils from three major citrus production areas in Florida was studied utilizing a batch equilibrium method. The dissipation of glyphosate was tracked in the field following its application at the rate of 4.20 kg ae ha-1. Soil leaching columns in greenhouse conditions were used to study the vertical movement of glyphosate. The results suggest that glyphosate has a relatively lower range of adsorption or binding (Kads = 14.28 to 30.88) in the tested soil types. The field dissipation half-life (DT50) of glyphosate from surface soil was found to be 26 days. Glyphosate moved vertically or leached into the soil profile, up to 40 cm in the soil column, when analyzed 40 days after herbicide application. The primary degradation product of glyphosate, i.e., aminomethyl phosphonic acid (AMPA), was also detected up to the depth of 30 cm below the soil surface, indicating the presence of microbial metabolism of glyphosate in the soil.

In the European Union, the demand for polyurethane is continually growing. In 2017, the estimated production value of polyurethane was 700,400T, of which 27.3% is taken to landfill, which causes an environmental problem. In this paper the behaviour of various polyurethane foams from the waste of different types of industries will be analysed with the aim of assessing their potential use in construction materials. In order to this, the wastes were chemically tested by means of CHNS, TGA, and leaching tests. They were tested microstructurally by means of SEM. The processing parameters of the waste was calculated after finding out its granulometry and its physical properties i.e. density and water absorption capacity. In addition, the possibility of incorporating these wastes in plaster matrices was studied by determining its rendering in an operational context, finding out its mechanical resistance to flexion and compression at 7 days, its reaction to fire as well as its weight per unit of area and its thermal behaviour. The results show that in all cases, the waste is inert and does not undergo leaching. The generation process of the waste determines the foam’s microstructure in addition to its physical-chemical properties that directly affect building materials in which they are included, thus offering different ways in which they can be applied.

This study presents a novel technique utilizing high frequency vibration to shorten treatment time and preserve alveolar bone in challenging orthodontic cases treated with Invisalign® clear aligners. Four non-growing orthodontic patients (age range 14-47 years old) with Class II skeletal patterns (convex profiles with retrognathic mandibles) who sought correction of their crowded teeth and non-surgical correction of their convex profiles were included in this study. These patients were treated using Invisalign clear aligners together with high frequency vibration (HFV) devices (120 Hz) (VPro5™) that were used by all patients for five minutes per day during active orthodontic treatment. Vertical control and forward rotation of the mandible for each patient was achieved through pre-programming the Invisalign to produce posterior teeth intrusion. Successful forward rotation of the mandibles achieved in all patients led to improvement of their facial convex profiles (ANB improved 2.1 + 0.5 degrees; FMA improved 1.2 +1.1 degrees). Dental decompensation was achieved by lingual tipping of the lower incisors and palatal root torque of upper incisors. The use of HFV together with Invisalign facilitated achieving these results within a 12+6 month period. In addition, more bone labial to the lower incisors after their lingual movement was noted. In conclusion, the use of HFV concurrent with SmartTrack Invisalign aligners allowed complex tooth movement and forward projection without surgery in non-growing patients with skeletal Class II relationships. The clinical impact and implications of this case series is that the use of HFV facilitates complex orthodontic tooth movement including posterior teeth intrusion and incisor decompensation in addition to increased bone formation labial to lower incisors that may minimize future gum recession due to their labial inclination.

The article discusses the main technologies for processing titanium-containing raw materials, and the advantages and disadvantages of various technological solutions. The analysis of the literature review showed that the traditional schemes for the production of titanium products are mainly focused on the use of ilmenite concentrates. In connection with the depletion of ilmenite deposits, in the near future there will inevitably be a need to switch to the use of complex ores - titanomagnetites. The obtaining of titanium dioxide from titanomagnetite raw materials with a high content of impurity components requires an individual approach for each specific deposit. It is proposed to consider the possibilities of further improvement of the development of a technological process for low-temperature (1000-1200 oC) processing of titanomagnetite concentrates with the production of pure titanium dioxide.

Conservation tillage and deep side-fertilization both hold the potential to reduce nitrogen leaching and improve grain yield and nitrogen use efficiency in fragrant rice cultivation practices. However, the combined impact of different tillage practices with deep side-fertilization on nitrogen leaching remains uncertain. Therefore, this study conducted on-site experiments for four rice growing seasons in both early and late seasons in 2018 and 2019, using the fragrant rice varieties "Meixiangzhan 2"(MX) and "Xiangyaxiangzhan"(XY). The four experimental treatments included:conventional tillage with regular fertilization (T1), conventional tillage with simultaneous deep fertilization (T2), reduced tillage with simultaneous deep fertilization (T3) , and no-tillage with simultaneous deep fertilization (T4). Our results indicate that the T4 treatment exhibited higher nitrogen leaching rates and potential nitrogen losses throughout the entire rice growth cycle, with a 4.51% increase in total nitrogen leaching and a 1.86% increase in potential nitrogen leaching compared to T1. In contrast, the T2 treatment demonstrated the lowest nitrogen leaching rate, resulting in a 6.01% reduction in total nitrogen leaching and a 9.57% decrease in potential nitrogen leaching compared to T1, demonstrating the most optimal performance. For MX, the T1 treatment resulted in lower daily grain outputs compared to the other treatments, with disparities ranging from 5.35% to 9.94%. Similarly, for the XY, the T1 treatment yielded significantly lower daily grain outputs compared to the other treatments, with discrepancies ranging from 6.26% to 10.81% during the late season of 2019. Overall, this study shows that conventional tillage with deep fertilization effectively reduces nitrogen leaching and boosts fragrant rice yields. Minimizing nitrogen leaching enhances nitrogen utilization efficiency. These insights highlight the significance of strategic fertilization and cultivation for environmental conservation and agricultural sustainability.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

In recent years, with the increasing research and development of the LED industry which contains GaN, it is expected that there will be a large amount of related wastes in the future. Especially the gallium has extremely high value of economic, therefore, it is necessary to establish the recycling system of the GaN waste. However, GaN is a direct-gap semiconductor and with high energy gap, high hardness, and high melting point make it difficult to recycle. Therefore, this study will analyze the physical characteristics of LED wastes containing GaN and carry out various leaching method to leach the valuable metals from the waste optimally. Different acids are used to find out the best reagent for leaching the gallium. Different experimental parameters are discussed such as the effect of the different acid agents , concentration, pressure, solid-liquid mass ratio, temperature, and time which influence the leaching efficiency of the gallium. In this study, various leaching methods which effect the leaching efficiency of the gallium are compared and the advantages and disadvantages are discussed. Finally, pressurized acid leaching method is preferred to leach the GaN waste, and hydrochloric acid is used as the leaching solution because of its better leaching efficiency of gallium. Eventually, the leaching efficiency of the gallium can reach to 98%.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

The use of nitrogen (N) fertilizers can have detrimental effects on the environment due to nitrate leaching. This study aims to examine the impact of N fertilizer source and application timing on wheat yield and nitrate leaching in various soil textures. A randomized complete block design (RCBD) was employed to conduct the experiment. The treatments consisted of two N fertilizer sources: ammonium nitrate (AN) and urea (NN), applied at three different times throughout the year, with a control treatment. The three application timings were total application before sowing (T₁), total application in spring (T₂), and half the amount before sowing and the other half in spring (T₃). The experiment was conducted in three different soil textures (sandy loam, silty clay loam, and silty clay), with three replications over three growing seasons: 2018-19 (Y₁), 2019-20 (Y₂), and 2020-21 (Y₃). The results indicated significant effects of different soil textures on grain yield. Specifically, the silty clay loam soil differed significantly from the sandy loam and silty clay soils in terms of grain yield. The interaction effects between the N fertilizer source and application timing were also found to be significant for all soil textures (p<0.01). In sandy loam and silty clay soils, the grain yield increased when using the T₃ application timing compared to the silty clay loam soil. Notably, the silty clay loam soil with the T₂ application timing exhibited the highest grain yield, with a yield of 6863.6 kg ha^-1. Furthermore, the study revealed that N fertilizers and their application timing significantly influenced the protein content in the silty clay and sandy loam soils. The protein percentages were 10.76 and 10.93 for the silty clay and sandy loam soils, respectively, following the T₂ treatment. Additionally, ammonium nitrate (AN) demonstrated a noticeable effect on the percentage of grain protein compared to urea (NN). In conclusion, the application timing of N fertilizers had an impact on grain yield and protein content in different soil textures. Moreover, nitrate concentration increased throughout the experiment, with the highest soil nitrate concentration observed in both fertilizer treatments, particularly in the sandy loam soil.

Modern technologies for recycling electronic waste (e-waste) impose high economic efficiency and environmental safety requirements. Among existing technologies, hydrometallurgy is considered the most promising technology for e-waste recycling. Increasing attention to the chlorination method is associated with the complex recycling of low-grade ores containing noble metals and secondary polymetallic raw materials. In this paper, we propose a new scheme for leaching metals from computer printed circuits (PCBs) pre-crushed in a disintegrator: the processes of chlorine production and hydrochlorination are implemented in one reactor under the action of alternating current (AC) of industrial frequency (50 Hz). It was found that complete leaching of gold is achieved from fine fractions of raw materials containing 0.03% and 0.01% of the gold at an experiment duration of 2 hours, a current density of 0.66 A·cm-2, and a solid/liquid ratio of 8.6 g·L-1. Under the same conditions of the electrochemical leaching process from the fraction of raw material with a gold content of 0.08%, the degree of metal leaching is 80.5%. At the same time, with an increase in the copper content in the raw material from 1.40% to 6.13%, an increase in the degree of its leaching from 84.6% to 95.2%, respectively, is observed. These results will serve as a foundation for developing a complex technology for recovering valuable metals from PCBs.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

Spent batteries recycling is an important way to obtain low-cost graphite. Nevertheless, the obtaining of crystalline graphite with a rather low density of defects is required for many applications. In the present work, high-quality graphites have been obtained from different kinds of spent batteries. Black masses from spent alkaline batteries (batteries black masses, BBM), and lithium-ion batteries from smartphones (smartphone black masses, SBM) and electric and/or hybrid vehicles (lithium-ion black masses, LBM) were used as starting materials. A hydrometallurgical process was then used to obtain recycled graphites by acidic leaching. Different leaching conditions were used depending on the type of the initial black mass. The final solids were characterized by a wide set of complementary techniques.

Poor soil health is a critical problem in many urban landscapes. Degraded soil restricts plant growth and microorganism activity, limiting the ability of urban landscapes to perform much needed ecosystem services. Incorporation of approximately 33% compost by volume into degraded soil has been proven to improve soil health and structure over time while avoiding the financial and environmental costs of importing soil mixes from elsewhere. However, additions of high volumes of compost could potentially increase the risk of nutrient loss through leaching and runoff. The objective of our study was to consider the effects of different compost amendments on soil health, plant health and susceptibility to nutrient leaching in order to identify ranges of acceptable compost characteristics that could be used for soil remediation in the urban landscape. We conducted a bioassay with Phaseolus vulgaris (Bush Bean) to measure the effect of nine composts from different feedstocks on various plant health parameters. We collected leachate prior to planting to measure nutrient loss from each treatment. We found that all compost amendments improved soil health. Nutrient-rich, manure-based composts produced the greatest plant growth, but also leached high concentrations of nitrate and phosphorus. Some treatments provided sufficient nutrients for plant growth without excess nutrient loss. We concluded, when incorporating as much as 33% compost by volume into a landscape bed, the optimal compost will generally have a C:N ratio of 10-20, P-content <1.0% and a soluble salt content between 1.0 and 3.5 mmhos/cm. These recommendations should ensure optimal plant and soil health and minimize nutrient leaching.

Filter Media (FM) sourced from recycled organic and mineral material offers a low cost and effective means of treating urban stormwater. Using recycled materials rather than from an increasingly scarce source of virgin materials (typically sandy loam soil) can ensure a sustainable long-term economy and environment. This paper presents results from the laboratory analysis and mathematical modeling to highlight the performance of recycled organic and mineral material in removing nutrients and metals from stormwater. Analysis included physical and chemical characterisation such as particle size distribution, saturated hydraulic conductivity (Ksat), bulk density, effective cation exchange capacity, and pollutant removal performance. Design mixes (DM), comprising a combination of organic and mineral materials, were characterised and used to develop/derive modelling design within the Model for Urban Stormwater Improvement Conceptualisation (MUSIC v6) [1]. Comparison is made to the Adoption Guidelines for Stormwater Biofiltration Systems - Summary Report [2] which were based on the Facility for Advancing Water Biofiltration (FAWB) guidelines to assist in the development of biofiltration systems, including the planning, design, construction and operation of those systems. An observed outcome from over two decades of biofiltration guideline development has been the exclusion of alternative biofilter materials due to claims of excessive leaching. Results from this study indicate that high nutrient and metal removal rates can be achieved over a range of hydraulic conductivities using design mixes of recycled organic and mineral materials that have a demonstrated equivalence to existing guideline specifications.

This study investigated the ability of a HYDRUS 1D model for predicting the vertical distribution of potassium iodine (200 ppm) in soil columns after amendment with five different common remediation materials (gypsum, lime, fly ash, charcoal and sawdust) at a rate of 2.5% (w/w), relative to an unamended control soil. Results shows that relative to the unamended soil, iodine leaching was decreased by all amendments but that the magnitude of the decreases varied with the soil amendment applied. Iodine content was highest in the upper layer of the soil columns and decreased progressively with soil depth. The model was evaluated via comparison of the model simulated values with measured values from the soil column studies. The results showed that the HYDRUS 1D model efficiency was near to 1, indicating that the stimulated results were near to the measured values. Therefore, this study showed that iodine leaching through a soil could be ascertained well using a HYDRUS 1D model. The model over predicted iodine leaching, resulting to a weak correspondence between the simulated and the measured results for iodine leaching. This suggests that the HYDRUS-1D model does not explain accurately different organic and inorganic amended soil and the preferential flow that occurs in these columns. This may be due to the fact that Freundlich isotherm, which is part of the transport equations, does not sufficiently describe the mechanism of iodine adsorption onto the soil particles. This study would help to select amendments for an effective management strategy to reduce exogenous iodine losses from agro-ecosystems. This would also improve understanding of iodine transport in soil profile.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

The Bayer process is the maim method of alumina production worldwide. The use of low-quality bauxites for alumina production results in the formation of a significant amount of technogenic waste - bauxite residue (BR). The Bayer reductive method is one possible way to eliminate BR stockpiling, but it requires high-pressure leaching at temperatures higher than 220 °C. In this research, the possibility of boehmitic bauxite atmospheric pressure leaching at both the first and second stages or high-pressure leaching at the second stage with the simultaneous reduction of hematite was investigated. Bauxite and solid residue after NaOH leaching were characterized using XRD, SEM-EDS, and Mössbauer spectroscopy methods. The first stage of leaching under atmospheric pressure with the addition of Fe(II) species in a strong alkali solution (330-400 g L–1 Na2O) results in a partial reduction of the iron minerals and an extraction of more than 60% of Si and 5-25% of Al (depending on caustic modulus of solution) after 1 h. The obtained desilicated bauxite was subjected to atmospheric leaching at 120 °C in a strong alkali solution (350 g L-1) or high-pressure leaching at 160-220 °C using the Bayer process mother liquor in order to obtain a concentrate with a magnetite content higher than 83 wt. %.

In order to formulate a reasonable water input model for cotton fields in southern Xinjiang, scientific and rational fertilization, reduce soil carbon leaching, and improve soil carbon sequestration capacity, the undisturbed soil column leaching test was used to simulate the current field management method in the study area. Two methods of drip irrigation and flood irrigation were set up, and three irrigation and three nitrogen fertilizer levels were used to carry out the undisturbed soil column leaching test. The results showed that the amount and mode of water and nitrogen input affected the distribution and leaching loss of organic carbon and inorganic carbon in soil. When the nitrogen application rate increased from 270 kg·hm-2 to 450 kg·hm-2, the leaching loss of soluble organic carbon and soluble inorganic carbon increased significantly. When the water input increased from 6000 m3·hm-2 to 9000 m3·hm-2, the leaching loss of DOC and DIC increased significantly. The carbon leaching loss under drip irrigation was higher than that under flood irrigation. The leaching rates of DOC and DIC were the fastest under the conditions of high water ( 9000 m3·hm-2 ) and high fertilizer ( 450 kg·hm-2 ). It shows that water and nitrogen input and irrigation methods are important factors affecting soil carbon leaching. In the case of excessive water input, long-term high-frequency irrigation is the main factor affecting carbon leaching.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Though nowadays germanium do not reach the range of popularity than other metals, i.e. rare earth elements, its utility in target industries makes of it also a strategic metal. Though germanium can be find in a series of raw materials, the principal source for its recovery is from secondary wastes of the zinc industry, and also, the recycle of germanium-bearing waste materials is becoming of interest. In this recovery, Hydrometallurgy is performing a key role to the successful achievement of this goal. The present work reviews the most recent applications (2023 and 2024 years) of hydrometallurgical operations on the recovery of germanium from different solid and liquid sources.

Acid in-situ leaching (ISL) is a common approach to the recovery of uranium in the subsurface. As some toxic and harmful substances might be produced by the chemical reactions among the injected sulphuric acid, the groundwater, and the porous media during leaching processes, the pollution control of the mining plan for ISL is important. In this study, a three-dimensional reactive transport modeling (3DRTM) was applied to decide the pollution control mining plan, considering the partial penetration through wellbore in confined aquifer and complex chemical reactions between main minerals. Based on the 3DRTM, different pumping ratio and non-uniform injection schemes were compared. The results show that the preferential pollution control mining plan is non-uniform injection ratio equal 0.1. By analyzing the characteristics of water table and streamline, it is concluded that the scheme has a strong hydraulic capture effect. In this scheme, the concentration of UO22+, H+, SO42- obtained by 3DRTM is lower. The inner well injection rate is 194.09 m3/d, the outer well injection rate is 158.89 m3/d, and the pumping rate is 264.00 m3/d. A reasonable suggestion is to adopt non-uniform injection mining mode in ISL.

The inner walls of drinking water distribution system (DWDS) are expected to be clean to ensure a safe quality of drinking water. In reality, complex physical, chemical and biological processes take place when water comes into contact with the pipe surface. This paper describes the impact of leaching different compounds from the water supply pipes into the drinking water and subsequent risks. Among these compounds there are heavy metals. It is necessary to prevent these metals to get into the DWDS. Those compounds are susceptible to impact the quality of the water delivered to population either by leaching dangerous chemicals into the water or by enhancing the development of microorganism growth on the pipe surface. The corrosion process of different pipes materials, scale formation mechanisms and the impact of bacteria formed in corrosion layers are discussed. Water treatment processes and the pipe materials also affect the water composition. Pipes materials act differently in the flowing and stagnation conditions. Also, they age differently (e.g metal based pipes are subjected to corrosion while polymer based pipes have a decreased mechanical resistance) and are susceptible to enhance bacterial film formation. This review helps to clarify what are the possible sources of compounds responsible for drinking water quality degradation. Also, it gives guidance on the measures that are needed to maintain a stable and safe drinking water quality.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

The boosted interest in the use of rare earth elements (REEs) in modern technologies had also increase the necessity of their recovery from various sources, including raw materials and wastes. Though Hydrometallurgy plays a key role in these recovery processes, some drawbacks (apparent or not) of these processes, had led to the development of a more environmental friendship subclass named Solvometallurgy, in which non-aqueous solvents substituted to the aqueous media of the hydrometallurgical processing. The non-aqueous solvents chosen for these usages are, besides ionic liquids (ILs), the so-named Deep Eutectic Solvents (DEEs). The utilization of DEEs included the leaching of REEs from the different sources containing them, and also in the separation-purification steps necessary for the yielding of these elements, normally as oxides or salts, in the most purified form. This work reviewed the most recent literature (2023 year) about the utilization of deep eutectic solvents in the recovery of REEs from various sources, and in the coupling of these two (DESs and REEs) to derived compounds to be used in other fields.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

Here, a process for leaching vanadium from calcified roasting pellets (CPVC) of vanadium-titanium iron concentrate by a two-stage sulfuric acid cycle was proposed. When the silicon removal acid concentration of the pellet in the first stage was 1.5 mol/L, the solid-liquid ratio was 6: 1, the silicon removal acid concentration of the leaching solution was 3.0 mol/L, and the standing time was 48 h, the silica gel formation time was 23 h, the filtration time was 70 s, and the loss rates of vanadium and iron were 1.52% and 0.17%, respectively. When the acid concentration was 2 mol/L, at room temperature, using a leaching time of 28 days, and a solid-liquid ratio of 5: 1 in the second stage, the total leaching rates of vanadium and iron were 75.52% and 0.71%, respectively. The concentration of vanadium in the leaching solution reached 6.80 g/L, and vanadium was directly precipitated without extraction. After secondary roasting, the crushing strength of the pellets reached 2250 N, which met the requirement for blast furnace iron making. The Eh-pH diagrams of the V-Fe-H2O system at different temperatures were plotted. Thermodynamically, it was difficult to selectively leach vanadium and iron by changing the conventional acid leaching conditions. In addition, the pellets before and after leaching were analyzed. The grade of iron in the pellets increased slightly after leaching, and the main phases in the pellets remained as Fe2O3 and Fe9TiO15. The S in the sulfuric acid solution entered the leached pellets during the acid leaching reaction and was removed by the secondary roasting of the leached pellets.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

One of the potential sources of rare-earth elements (REEs) is the solid waste from alumina industry - bauxite residue, known as “red mud” (RM). The main REEs from the raw bauxite are concentrated in RM after the Bayer leaching process. The earlier worldwide studies were focused on the scandium (Sc) extraction from RM by concentrated acids to enhance the extraction degree. This leads to the dissolution of major oxides (Fe2O3 and Al2O3) from RM. This article studies the possibility of selective Sc extraction from alkali fusion red mud (RMF) by diluted nitric acid (HNO3) leaching at pH ≥ 2 to prevent co-dissolution of Fe2O3. RMF samples have been analyzed by X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), electron probe microanalysis (EPMA), and inductively coupled plasma mass spectrometry (ICP-MS). Sc extraction has been found to be 71.2 % at RMF leaching by HNO3 at pH=2 and at 80 °C during 90 min. The kinetic analysis of experimental data by the shrinking core model has shown that Sc leaching process is limited by the interfacial diffusion and the diffusion through the product layer. The apparent activation energy (Ea) was 19.5 kJ/mol. We have established that according to EPMA of RMF, Sc is associated with iron minerals; it could act as the product layer. The linear dependence of Sc extraction of magnesium (Mg) extraction has been revealed. This fact indicates that Mg can act as a leaching agent of Sc presented in RMF by ion-exchangeable phase.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

Addressing non-unions involves stabilizing the affected area through osteosynthesis and improving bone biology using bone grafts. However, there is no consensus on the optimal treatment method. This study aims to compare outcomes of non-union revision using conventional treatment methods (metal hardware ± graft) versus osteosynthesis with the human, allogeneic cortical bone screw (Shark Screw®). Thirty-four patients underwent conventional treatment, while 28 cases received Shark Screws®. Patient demographics, bone healing, time to bone healing, and complications were assessed. Results revealed a healing rate of 96.4% for the Shark Screw® group, compared to 82.3% for the conventionally treated group. The Shark Screw® group exhibited a tendency for faster bone healing (9.4±3.2 vs. 12.9±8.5 weeks, p=0.05061). Hardware irritations led to six metal removals in the conventional group versus two in the Shark Screw® group. The Shark Screw® emerges as a promising option for personalized non-union treatment in the foot, ankle, and select lower leg cases, facilitating effective osteosynthesis and grafting within a single construct, promoting high union rates, low complications, and a rapid healing process.

Reductive leaching in the Bayer cycle using of iron (2+) allows Al extraction to be significantly increased by magnetization of Al-goethite and Al-hematite. However, the use of expensive iron (2+) salts or iron powder as a source of iron (2+) leads to a significant increase in production costs. In this work, the feasibility of a new method, the reductive leaching of bauxite using an electrolysis process, was investigated. Reduction of iron minerals of boehmitic bauxite in both Bayer solution and purely alkaline solutions were carried out. Experiments were performed using a plate cathode and a bauxite suspension in alkaline solution, as well as using a bulk cathode with a stainless-steel mesh at the bottom of the cell as the current supply. During the electrolysis process, the potential of the cathode relative to the reference electrode was measured as a function of current at different concentrations of solid (100-300 g L–1) and suspension temperatures (95-120 °C). It is shown that the current efficiency using suspension and plate cathode with the predominant deposition of Fe doesn’t exceed 50% even with the addition of magnetite to increase the contact of solid phase with the current supply. With the use of a bulk cathode, the reduction of iron minerals leads predominantly to the formation of magnetite with the efficiency of using electric current more than 80%. As a result of preliminary desilication and electroreduction it is possible to extract more than 97% of Al from bauxite, and to increase the iron content in the bauxite residue to 57-58%.

The problem of effective immobilization of liquid radioactive waste (LRW) is key to the successful development of nuclear energy. The possibility of using magnesium potassium phosphate (MKP) compound for LRW immobilization on the example of nitric acid solutions containing actinides and rare earth elements (REE), including high level waste (HLW) surrogate solution is considered in the research work. Under the study of phase composition and structure of the MKP compounds obtained by the XRD and SEM methods, it was established that the compounds are composed of crystalline phases - analogues of natural phosphate minerals (struvite, metaankoleite). The hydrolytic stability of the compounds was determined according to the semi-dynamic test GOST R 52126-2003. Low leaching rates of radionuclides from the compound are established, including a differential leaching rate of ²³⁹Pu and ²⁴¹Am - 3.5 × 10^-7 and 5.3 × 10^-7 g/(cm²∙day). As a result of the research work it was concluded that the MKP compound is promising for LRW immobilization and can become an alternative material combining the advantages of easy implementation of the technology like cementation and the high physical and chemical stability corresponding to a glass-like compound.

The chemical reaction of ion-adsorption type rare earth during in-situ leaching process is accompanied by ion migration and charge movement, making the leaching process electrochemical in nature. The chemical reaction rate plays an important role in the leaching rate of rare earth elements. In this work, electrochemical impedance spectroscopy (EIS) was used to reveal characteristics of electrical resistance alteration and leaching rate of rare earth elements during in-situ leaching. The equivalent circuit model of the leaching process was established, and two critical parameters of solution resistance Rs and charge transfer resistance Rt were analyzed to reflect the electrochemical characteristics. According to the characteristics of electrical resistance alteration, the leaching process was divided into four stages: wetting, reaction, equilibrium, and top water stage. The resistance parameters Rs and Rt decreased first and then increased during the leaching process. The maximum value of Rs was 1330Ω∙cm2 at the end of the top water stage, and the minimum value was 135Ω∙cm2 at the beginning of the equilibrium stage. The maximum value of Rt was 8310Ω∙cm2 at the beginning of the leaching stage, and the minimum value was 21Ω∙cm2 at the end of the reaction stage. Rs and Rt were negatively correlated with the pore size and chemical reaction rate during leaching. With increasing of pore size and reaction rate , the resistance parameter decrease. This study provide a new idea for intelligent monitoring of rare earth ore.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

rdinary people and political leaders must know the sources of greenhouse gas emissions and their effect on global climate change before they have ability to make decisions to reduce emissions and increase sinks of these gases. These people must, however, understand where greenhouse gas emissions are formed and how reductions can be made: they must understand where carbon dioxide sinks are and how to preserve or increase these sinks. North Savo is the example used in this work to describe the present emissions and sinks. There are proposals on what should and could be done to reduce greenhouse gas emissions caused by traffic, heating, forests and agriculture. There are possibilities of reducing emissions of greenhouse gases in traffic and heating in spite of the fact that the province has a low population density with long distances between homes and workplaces and schools, and a cold climate. We believe that research will also find solutions for reducing greenhouse gases and protecting waters, which are used for recreational purposes and for raw water of drinking water in many places. Luckily forests cover large areas of North Savo and their growth is an important carbon dioxide sink. In addition, forest soils serve as a valuable storage of carbon. Besides carbon dioxide emissions, emissions of nitrous oxide and methane must also be considered since they are more potent greenhouse gases than carbon dioxide and land use can thus influence these gas emissions.

Reporting on CSR activities has become the essence of reporting for modern business entities. In this regard, particular attention is paid to public interest companies. Therefore, the following paper aims to answer the question of whether there are differences in the linguistic structure of the studied CSR reports in three selected industry indices on the Warsaw Stock Exchange (WSE) in Poland, i.e. WIG-energy index, WIG-fuel index, WIG-mining index and their relationship with the performance of selected companies. The study was conducted on a purposely selected sample of companies between 2013 and 2018. A total of 138 CSR reports and 138 annual separate financial statements prepared in accordance with international balance sheet law were collected. The study was carried out based on a panel regression model. It was found that CSR reports contained similar average percentages of parts of speech such as nouns and adjectives. When linking the economic performance of companies, expressed with selected indices, to the information on the implementation of CSR concepts, it was revealed that the results are more likely to describe business performance when it is satisfactory.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

In a single-center, retrospective study, 22 cases were enrolled and divided into two groups: those who underwent surgical wide excision (group A) and those who did not (group B). The study included 13 cases in group A and 9 cases in group B. In group A, 6 cases solely underwent surgical wide excision, while 7 cases received additional treatments like radiotherapy or chemotherapy. Conversely, in group B, 4 cases received chemotherapy, 4 cases received radiotherapy, and 1 case was managed through observation alone. The mean follow-up time was 60.15 months in group A and 43.44 months in group B, with no significant difference observed. In group A, 9 cases resulted in mortality, whereas 6 cases died within the follow-up period in group B. Lesion-free intervals post-operation were observed predominantly in group A, while 7 cases in group B never experienced freedom from skin lesions. Kaplan-Meier survival curve analysis demonstrated a significant difference between the survival curves of the two groups (P = 0.046). Among non-HIV Kaposi’s sarcoma patients, surgical wide excision appears to have a role in treatment. Patients in group A exhibit a more favorable outcome in the survival curve analysis.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

Multiphase systems are important in minerals processing, and usually include solid-solid and solid-fluid systems. Examples of operations in multiphase systems include flotation, dewatering, and magnetic separation, among several other unit operations. In this paper, the current trends in the process system engineering tasks of modeling, design, and optimization, in multiphase systems, are analyzed. Different scales of size and time are included, and therefore the analysis includes modeling at the molecular level and unit operation level, and the application of optimization for the design of a plant. New strategies for the modeling and optimization of multiphase systems are also included, with a strong focus on the application of artificial intelligence (AI) and the combination of experimentation and modeling with response surface methodology (RSM). The paper finishes with tools to study the uncertainty, both epistemic and stochastic, which is present in all mineral processing operations. It is shown that all these areas are very active and can help to understand, operate, design, and optimize mineral processing that involves multiphase systems.

Mediterranean climate is marked by arid climate conditions in summer, therefore, crop irrigation is crucial to sustain plant growth and productivity in this season. If groundwater is utilized for irrigation, an impressive water pumping is needed to satisfy crop water requirements at catchment scale. Consequently, irrigation water quality gets worse, specifically considering groundwater salinization near the coastal areas due to seawater intrusion, also triggering soil salinization. With reference to an agricultural coastal area in the Mediterranean basin (Southern Italy), close to the Adriatic sea, an assessment of soil salinization risk due to processing tomato cultivation was carried out. A simulation model was arranged to perform, on daily basis, a water and salt balance along the soil profile. Long-term weather data and soil physical parameters representative of the considered area were utilized in applying the model, also considering three salinity levels of irrigation water. Based on the climatic analysis performed and the model outputs, the probability of soil salinity came out very high, such as to seriously threaten tomato yield. Autumn-winter rainfall resulted frequently insufficient to leach excess salts away from the soil profile and reach sustainable conditions of tomato cultivation. Therefore, alternative cropping strategies were prospected.

For the treatment of cancer and other diseases, therapeutic targeting of non-coding RNAs (ncRNAs) such as microRNAs (miRNAs) and long non-coding RNAs (lncRNAs) is an attractive approach. RNA-based therapeutics have been extensively researched over the past decade, with antisense oligonucleotides and small interfering RNAs being the most commonly used. Some of these have even gained FDA approval. However, the results of trials have been mixed, with some studies reporting strong effects while others have shown limited effectiveness or toxicity. Alternative treatments, such as antimiRNAs, are currently in clinical trials. There is growing interest in the use of lncRNA-based therapies. This Perspective discusses the main challenges of ncRNA therapeutics, including specificity, delivery and tolerability. It also highlights emerging approaches that aim to improve their success.

Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

An exhaustive list of thirteen instances of reports confirming experimentally the relativistic Doppler relation, are examined. For those involving longitudinal Doppler, the non-relativistic relation is seen to be confirmed, within the reported experimental accuracies, to the same degree as the standard relativistic relation. Higher values of the speed of the emitter would be required to examine further the claimed confirmations. For those reports involving saturation spectroscopy, there is much confusion over the appropriate Doppler relation to be used, together with some serious analytical flaws. For the two cases that involve transverse Doppler, there are seen to be either serious faults in the theoretical part, or intrusion from the first order effect. Therefore, the reported conclusions - that the results for the experiments confirm the relativistic SR relation - cannot be justified by any of the experimental works.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{F}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We show that the public, secret and channel keys become indistinguishable to the eavesdropper under matrix multiplication. Remarkably, for achieving a 512-bit security level, the public key is 1024 bits and the private key is 768 bits, making them the smallest keys among post-quantum key exchange algorithms. Also, we discuss how to achieve key authentication, interdomain certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{Z}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We claim that the unique eavesdropper's opportunity to get the secret/private key is by means of an exhaustive search which is equivalent to the unsorted database search problem. Furthermore, we show that the secret/private keys become indistinguishable to the eavesdropper. Remarkably, to achieve a 512-bit security level, the keys (public/private) are of the same size when matrix multiplication is done over a reduced 8-bit size modulo. Also, we discuss how to achieve key certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in the last section we present a concerning numerical example and the respective software.

Let $\mathbb{K}$ be a non-Archimedean (complete) valued field satisfying \begin{align*} \left|\sum_{j=1}^{n}\lambda_j^2\right|=\max_{1\leq j \leq n}|\lambda_j|^2, \quad \forall \lambda_j \in \mathbb{K}, 1\leq j \leq n, \forall n \in \mathbb{N}. \end{align*} For $d\in \mathbb{N}$, let $\mathbb{K}^d$ be the standard $d$-dimensional non-Archimedean Hilbert space. Let $m \in \mathbb{N}$ and $\text{Sym}^m(\mathbb{K}^d)$ be the non-Archimedean Hilbert space of symmetric m-tensors. We prove the following result. If $\{\tau_j\}_{j=1}^n$ is a collection in $\mathbb{K}^d$ satisfying $\langle \tau_j, \tau_j\rangle =1$ for all $1\leq j \leq n$ and the operator $\text{Sym}^m(\mathbb{K}^d)\ni x \mapsto \sum_{j=1}^n\langle x, \tau_j^{\otimes m}\rangle \tau_j^{\otimes m} \in \text{Sym}^m(\mathbb{K}^d)$ is diagonalizable, then \begin{align}\label{WELCHNONABSTRACT} \max_{1\leq j,k \leq n, j \neq k}\{|n|, |\langle \tau_j, \tau_k\rangle|^{2m} \}\geq \frac{|n|^2}{\left|{d+m-1 \choose m}\right| }. \end{align} We call Inequality (\ref{WELCHNONABSTRACT}) as the non-Archimedean version of Welch bounds obtained by Welch [\textit{IEEE Transactions on Information Theory, 1974}]. We formulate non-Archimedean Zauner conjecture.

Nonionizing millimeter-waves (MMW) interact with cells in a variety of ways. Here the inhibited cell division effect was investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm2 safety standards. Irradiation using a power density of about 1.0 mW/cm2 , SAR over 5-6 hours on 50 cells/μl samples of Saccharomyces cerevisiae model organism resulted in 62% growth rate reduction compared to the control (sham). The effect was specific for 85-105 GHz range, and was energy and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deleted cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause permanent genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm2) and compared to that of a compact waveguide (17.17 mW/cm2) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. We have shown that non-thermal MMW radiation has potential for future use in treatment of yeast related diseases and other targeted biomedical outcomes.

Nonionizing millimeter-waves (MMW) are reported to interact with cells in a variety of ways. Possible mechanisms of the inhibited cell division effect were investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm² safety standards. ~1.0 mW/cm² exposure over 5-6 hours treatment on 50 cells/μl samples of Saccharomyces cerevisiae model organism, resulted in 62% growth rate reduction compared to control (sham). The effect was specific for 85-105 GHz range and energy dose and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deletion cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm²) and compared to that of a compact waveguide (17.17 mW/cm²) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. Combinations of MMW mediated Structure Resonant Energy Transfer (SRET), membrane modulations eliciting signaling effects, and energetic resonance with biomolecules were indicated to be responsible for the observations reported. Our results provide novel mechanistic insights enabling innovative applications of nonionizing radiation procedures for eliciting targeted biomedical outcomes.

Non-isocyanate polyurethane synthesis by non-Sn catalysis is an essential challenge toward green polyurethane synthesis. Bismuth compounds are attractive candidates due to their low cost, low toxicity, and availability to urethane chemistry. We applied various Bi catalysts to the self-polycondensation of a bishydroxyurethane monomer and found BiCl3 to be an excellent catalyst through optimization. The catalytic activity and price of BiCl3 are comparable to those of Bu2SnO, while its toxicity is significantly low. BiCl3 is, therefore, a promising alternative to Sn-based catalysts in non-isocyanate polyurethane synthesis.

Wine is a processed beverage that offers high nutritional and health benefits. It is produced from grape must, which undergoes fermentation by yeasts (and sometimes lactic acid bacteria) to create a product that is highly appreciated by consumers worldwide. However, if only one type of yeast, specifically Saccharomyces cerevisiae, were used in the fermentation process, the resulting wine would lack aroma and flavor and may be rejected by consumers. To produce wine with a desirable taste and aroma, non-Saccharomyces yeasts are necessary. These yeasts contribute volatile aromatic compounds that significantly impact the wine’s final taste. They promote the release of primary aromatic compounds through a sequential hydrolysis mechanism involving several glycosidases unique to these yeasts. This review will discuss the unique characteristics of these yeasts (Schizosaccharomyces pombe, Pichia kluyveri, Torulaspora delbrueckii, Wickerhamomyces anomalus, Metschnikowia pulcherrima, Hanseniaspora vineae, Lachancea thermotolerans, Candida stellata, and others) and their impact on wine fermentations and co-fermentations. Their existence and the metabolites they produce enhance the complexity of wine flavor, resulting in a more enjoyable drinking experience.

Post-quantum public cryptosystems introduced so far do not define an scalable public key infrastructure for the quantum era. We demonstrate here a public certification system based in Lizama’s non-invertible Key Exchange Protocol which can be used to implement a public key infrastructure (PKI), secure, scalable, interoperable and efficient. We show functionality of certificates across different certification domains. Finally, we discuss that non-invertible certificates can exhibit Perfect Forward Secrecy (PFS).

It is well established in literature that the public debt and economic growth bear positive and non-linear relationship. However, in recent literature, evidence of no causal relationship is found when accounted for endogeneity in case of advanced economies (Panizza & Presbitero, 2014). Chudik, Mohaddes, Pesaran, & Raissi, (2017) analyse the data on forty countries and find no evidence of universally applicable threshold effect in the relationship between debt and growth. These advancements in the debt-growth literature provides the motivation to re-explore the relationship between public debt and economic growth under non-linearity and endogeneity in context of developing economies of South Asia including Pakistan, India, Bangladesh and Sri-Lanka for the period 1980-2014. There exists a significant, positive but nonlinear relationship between the public debt and economic growth for the selected set of developing countries when accounted for endogeneity and non-linearity. The negative association between the public debt and economic growth for SAARC region is found when the debt level is higher than 61% of GDP which is quite lower than developed economies (90% of GDP). Individual threshold levels for debt-to-GDP ratio divulge that Sri Lanka, Pakistan and India need to control their public borrowings as their current debt levels are higher and/or around the respective threshold levels.

We establish a new Gagliardo-Nirenberg inequality characterized by radial symmetry and involving potentials exhibiting pure power polynomial behaviour. As an application of our result, we investigate the existence of extremals for this inequality, which also correspond to stationary solutions for the nonlinear Schrödinger equation with inhomogeneous nonlinearity, competing with Hs-subcritical nonlinearities, either of local or non-local nature.

Non-alcoholic steatohepatitis (NASH), which is the most severe manifestation of non-alcoholic fatty liver disease (NAFLD), has been recognized as a major hepatocellular carcinoma (HCC) catalyst. However, the molecular mechanism of NAFLD-NASH-HCC sequence remains unclear and a specific and effective treatment for NASH has not yet been established. The progress in this field depends on the availability of reliable preclinical models which show the steady progress to NASH, liver cirrhosis, and HCC. However, most of NASH mouse models that have been described to date develop NASH generally for more than 24 weeks and there is an uncertainty of HCC development. To overcome such shortcomings of experimental NASH studies, we established a novel NASH-HCC mouse model with very high reproducibility, generality, and convenience. We treated male C57BL/6J mice with a newly developed choline-deficient and methionine-restricted high-fat diet (CDMRHFD) for 60 weeks. Treatment of CDMRHFD for 3 weeks revealed marked steatosis, lobular inflammation, and fibrosis, histologically diagnosed as NASH. Liver cirrhosis was observed in all mice with 36-week treatment. Liver nodule emerged at 12 weeks of the treatment, and diameter >2 mm liver tumors developed in all mice at 24 weeks of the treatment. In conclusion, our rapidly progressive and highly reproducible NASH-liver cirrhosis-HCC model is helpful for preclinical development and research on the pathogenesis of human NAFLD-NASH-HCC. Our mouse model would be useful for the development of novel chemistry for NASH-HCC-targeted therapies or HCC prevention strategies.

(1) Background: Although multiple studies have reported on the therapeutic effects of Atezo+Bev for the treatment of NASH-related liver cancer, few studies have focused on its effect on liver reserve. Here, we aimed to compare the changes in hepatic reserve during the Atezo+Bev treatment of NAFLD/NASH-related HCC and of non-NAFLD/non-NASH-related HCC. (2) Methods: We retrospectively compared the changes in ALBI score in 109 patients with NAFLD/NASH or non-NAFLD/non-NASH during 12 weeks of treatment with Atezo+Bev for advanced HCC between September 2019 and January 2022. PSM was performed, and the OS, PFS, and PPS of the two groups were compared. (3)Results: The ALBI after 12 weeks of Atezo+Bev treatment was significantly worse in the NAFLD/NASH group than in the non-NAFLD/non-NASH group. Analysis of the 24 propensity score-matched pairs of cases with NAFLD/NASH or non-NAFLD non-NASH yielded similar results. The prognoses of the two groups were similar with respect to OS and PFS, but the NAFLD/NASH group had a significantly shorter PPS. The 24 matched pairs had similar OS and PFS, but the PPS of the NAFLD/NASH group was shorter. (4)Conclusion: Atezo+Bev treatment may worsen hepatic reserve, and there-fore life expectancy, in patients with NAFLD/NASH-related liver cancer.

This article develops a duality principle and a related convex dual formulation suitable for a large class of models in physics and engineering. The results are based on standard tools of functional analysis, calculus of variations and duality theory. In particular, we develop applications to a model in non-linear elasticity.

The connection of two phenomena - non-conservative friction forces and dissipation-induced instability can lead to many interesting engineering problems. The paper studies general material-dependent damping influence on dynamical instability of disc brake systems leading to brake squeal. The effect of general damping is demonstrated on a minimal and complex model of a disc brake. A complex system including material-dependent damping is defined in the commercial finite element software. The finite element model validated by experimental data on the brake-disc test bench is used to compute the influence of a pad and a disc damping variations on system stability by complex eigenvalue analysis. Analyzes show a significant sensitivity of the experimentally verified unstable mode of the system to the ratio of the damping between the disc and the friction material components.

Near-fault ground motions can cause severe damage to civil structures, including bridges. Safety assessment of these structures for near fault ground motion is usually performed through Non-Linear Dynamic Analyses, while faster methods are often used. IMPAb (Incremental Modal Pushover Analysis for Bridges) permits to investigate the seismic response of a bridge by considering the effects of higher modes, which are often relevant for bridges. In this work, IMPAb is applied to a bridge case study considering near-fault pulse-like ground motion records. The records were analyzed and selected from the European Strong Motion Database and the pulse parameters were evaluated. In the paper results from standard pushover procedures and IMPAb are compared with nonlinear Response-History Analysis (NRHA), considering also the vertical component of the motion, as benchmark solutions and incremental dynamic analysis (IDA). Results from the case study demonstrate that the vertical seismic action has a minor influence on the structural response of the bridge. Therefore IMPAb, which can be applied considering vertical motion, remains very effective conserving the original formulation of the procedure, and can be considered a well performing procedure also for near-fault events.

Abrasive Water Jet Machining (AWJM) is a non-conventional machining process that, unlike other methods, is deemed superior because of its applicability, versatility, and no heat-affected zones in the target material. The main objective of this paper was to develop a cheap, practical model for a low-pressure water jet cutting machine and provide some empirical test data for cutting delicate materials. Proper design calculations were performed and are included for both the water jet machine and the two-axis numerical control. Finite Element Analysis results validate the structural integrity of beams and columns in AWJM. Computational Fluid Dynamic analysis of the nozzle shows good agreement with the theoretical calculations regarding the pressure and velocity of the water-abrasive mixture exiting the nozzle. Modal analysis in ANSYS was done to mitigate potential failure due to resonance induced by vibrations. Limited testing on various thicknesses of polystyrene foam ranging from 1-5 mm thickness and rubber sheet of 1 mm thickness showed that even low pressure of 25-30 bar was sufficient to produce a kerf without any burr. However, extensive testing to report optimized parameters like nozzle transverse speed, standoff distance, abrasive flow rate, etc for working at low-pressure ranges is still a consideration for future investigation.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

Turbulent dissipation is a central issue in the star and galaxy formation process. Its fundamental property of space-time intermittency, well characterised in incompressible laboratory experiments, remains elusive in cosmic turbulence. Progress requires the combination of state-of-the-art modelling, numerical simulations and observations. The power of such a combination is illustrated here where the statistical method intended to locate extrema of velocity shears in a turbulent field is applied to numerical simulations of compressible magneto-hydrodynamical (MHD) turbulence dedicated to dissipation scales and to a nearby turbulent diffuse molecular cloud. We demonstrate that short-spacing increments of observables can detect strongly dissipative structures. In our simulations, we compute structure functions of various synthetic observables and show that they verify Extended Self-Similarity. This allows to compute their intermittency exponents and we show how they could help constraining some properties of the underlying three-dimensional turbulence. In observations of a turbulent cloud close to the Sun in our Galaxy, a remarkable coherent structure of velocity shear extremum is disclosed . At the location of the largest velocity shear, this coherent structure is found to foster 10 × more carbon monoxide molecules than standard diffuse molecular gas, an enrichment supported by models of non-equilibrium warm chemistry triggered by turbulent dissipation. The power of the combination between modelling and observations is also illustrated by observations of the CH+ cation that provide unique quantitative informations on the kinetic energy trail in the massive, multi-phase and turbulent circum-galactic medium of a galaxy group at redshift z = 2.8.

In this paper is presented the design and syntheis of a dynamic output feedback neural network controller for a non-holonomic mobile robot. First the dynamic model of a non-holonomic mobile robot is presented, in which these constraints are considered for the mathematical derivation of a feasable representation for this kind of robot. Then two control strategies are provided based on kinematic control for this kind of robot. The first control strategy is based on driftless control, this means, that considering that the velocity vector of the mobile robot is orthogonal to its restriction a dynamic output feedback and neural network controller is designed in order that the control action would be zero only when the velocity of the mobile robot is zero. The Lyapunov stability theorem is implemented in order to find a suitable control law. Then another control strategy is designed for trajectory tracking purposes, which similar to the driftless controller, a kinematic control scheme is provided but suitable to implement in more sophisticated hardware. In both control strategy a dynamic control law is provided along with a feedforward neural network controller, so in this way, by the Lyapunov theory the stability and convergence to the origin of the mobile robot position coordinates is ensured. Finally, two numerical experiment are presented in order to validate the theoretical results synthetized in this research study. Discussions and conclusions are provided in order to analyze the results found in this research study.

Non-vertebrate species represent about ~95% of known metazoan (animal) diversity. They remain to this day relatively unexplored genetically, but understanding their genome structure and function is pivotal for expanding our current knowledge of evolution, ecology and biodiversity. Following the continuous improvements and decreasing costs of sequencing technologies, many genome assembly tools have been released, leading to a significant amount of genome projects being completed in recent years. In this review, we examine the current state of genome projects of non-vertebrate animal species. We present an overview of available sequencing technologies, assembly approaches, as well as pre and post-processing steps, genome assembly evaluation methods, and their application to non-vertebrate animal genomes.

Background: Thousands of genetic variants have been associated with hematological traits, though target genes remain unknown at most loci. Also, limited analyses have been conducted in African ancestry and Hispanic/Latino populations; hematological trait associated variants more common in these populations have likely been missed. Methods: To derive gene expression prediction models, we used ancestry-stratified datasets from the Multi-Ethnic Study of Atherosclerosis (MESA, including N=229 African American and N=381 Hispanic/Latino participants, monocytes) and the Depression Genes and Networks study (DGN, N = 922 European ancestry participants, whole blood). We then performed a transcriptome-wide association study (TWAS) for platelet count, hemoglobin, hematocrit, and white blood cell count in African (N = 27,955) and Hispanic/Latino (N = 28,324) ancestry participants. Results: Our results revealed 24 suggestive signals (p < 1×10^(-4)) that were conditionally distinct from known GWAS identified variants and successfully replicated these signals in European ancestry subjects from UK Biobank. We found modestly improved correlation of predicted and measured gene expression in an independent African American cohort (the Genetic Epidemiology Network of Arteriopathy (GENOA) study (N=802), lymphoblastoid cell lines) using the larger DGN reference panel; however, some genes were well predicted using MESA but not DGN. Conclusions: These analyses demonstrate the importance of performing TWAS and other genetic analyses across diverse populations and of balancing sample size and ancestry background matching when selecting a TWAS reference panel.

The quality and shelf-life of NCS (Non-centrifugal sugar) mainly depend on the moisture content present in it. NCS formed by the current practice of open sun drying contains moisture substantially greater than the acceptable level of 3%. This paper presents the work taken up to design a tunnel dryer to attain require moisture content in granular NCS for various load conditions. Initially, an experimental investigation had been carried out on a laboratory scale dryer to achieve required moisture content (< 3%) for various load conditions. This experimental data was used for validating two drying models and found that one of the models is best suitable for designing an industrial-scale dryer. For various load conditions on each tray and dryer exit temperature, nine different cases were arrived at. The number of trucks, trays, drying time and energy requirements were computed using the suitable theoretical model. Tunnel dryer with a length of 18 m, a height of 1.2 m, a width of 1 m, number of trucks of 18 and 24 number of trays on each truck was found to be the suitable dryer to dry 1 tone of NCS based on the minimum energy requirement of 176.49 MJ, and a minimum drying time of 68 minutes.

Untranslated regions (UTRs) of flaviviruses contain a large number of RNA structural elements involved in mediating the viral life cycle, including cyclisation, replication, and encapsidation. Here we report on a comparative genomics approach to characterize evolutionarily conserved RNAs in the 3'UTR of tick-borne, insect-specific and no-known-vector flaviviruses in silico. Our data support the wide distribution of previously experimentally characterized exoribonuclease resistant RNAs xrRNAs within tick-borne and no-known-vector flaviviruses and provide evidence for the existence of a cascade of duplicated RNA structures within insect-specific flaviviruses. On a broader scale, our findings indicate that viral 3'UTRs represent a flexible scaffold for evolution to come up with novel xrRNAs

The aim of the study was to identify factors associated with non-adherence to tuberculosis (TB) preventive treatment among contacts with latent TB infection of new cases of pulmonary TB cases reported in Catalonia in 2019-2021. All contacts aged 18 years or older with a latent TB infection who received a TB preventive treatment were included in the study. The Chi square test and the odds ratios (OR) were used to assess the association between non-adherence to TB preventive treatment and the study variables, considering a p < 0.05 as statistically significant. Multiple logistic regression analysis was used to detect the in-dependent factors associated with TB preventive treatment non-adherence, considering a p < 0.05 as statistically significant. The percentage of non-adherence to TB preventive treatment found in this study was 23.7%. A multivariable logistic regression analysis determined that the following factors were significantly associated with TB preventive treatment non-adherence among adult contacts: “exposure at school or workplace” (aOR = 3.34), “exposure to an index case without laboratory confirmation of TB” (aOR = 2.07), “immigrant contact” (aOR = 1.81), “male gender” (aOR = 1.75) and “exposure duration <6 hours per week or sporadic exposure” (aOR = 1.60). By contrast, the factor “short-term TB preventive treatment regimen” (aOR = 0.38) was significantly associated with a lower treatment non-adherence. Adherence to TB preventive treatment should be improved among adult contacts of TB pulmonary cases with latent TB infection by recommending short-term treatment regimens and by developing health education activities, with a greater focus on contacts with factors associated with treatment non-adherence.

Non-alcoholic beer (NAB) or low alcoholic beer (LAB) are taking over the market with a growing sale. Sus-tainable recycling and valorization of exhausted brewer’s spent grains (BSG) coming from craft beer is a relevant issue in brewing process. In this work, recycled BSG and BSG+GJ (supplemented with 10% grape juice) were used as wort-substrate to inoculate already selected non-conventional yeasts to produce NABLAB craft beer. Results showed that wort composed by only recycled BSG produced appreciate NAB beers (ethanol from 0.12% to 0.54 % v/v) while the addition of 10% of grape juice made LAB beers (ethanol from 0.82 to 1.66 % v/v). As expected, volatile compounds production was highest with the addition of grape juice. Lachancea thermotolerans confirmed the lactic acid production and, as Saccharomyces cerevisiae, is characterized by (in both worts) ethyl butyrate and isoamyl acetate, while Torulaspora delbrueckii produced relevant amounts of exanol, phenylethyl acetate and β-phenyl ethanol (wort added with grape juice). Wickeramhomyces anomalus and Pichia kluyvery showed consistent volatile production but only in wort with grape juice addition where a fermentation activity was exhibited. The overall results indicated that reused BSGs, non-conventional yeasts and grape juice is a suitable strategy for specialty NABLAB beer.

With increased vulnerabilities and vast technology landscapes, it is extremely critical to build systems which are highly resistant to cyber-attacks, to break into systems to exploit. It is almost impossible to build 100% secure authentication & authorization mechanisms merely through standard password / PIN (With all combinations of special characters, numbers & upper/lower case alphabets and by using any of the Graphical password mechanisms). The immense computing capacity and several hacking methods used, make almost every authentication method susceptible to cyber-attacks in one or the other way. Only proven / known system which is not vulnerable in spite of highly sophisticated computing power is, human brain. In this paper, we present a new method of authentication using a combination of computer’s computing ability in combination with human intelligence. In fact this human intelligence is personalized making the overall security method more secure. Text based passwords are easy to be cracked ^[6]. There is an increased need for an alternate and more complex authentication and authorization methods. Some of the Methods ^{[7] [8]} in the category of Graphical passwords could be susceptible, when Shoulder surfing/cameras/spy devices are used.

Previous studies demonstrate the critical importance of non-coding RNAs interfacing with chromatin-modifying machinery resulting in promoter-enhancer-based gene regulation and raise the possibility that many other enhancer-like RNAs may operate via similar mechanisms. Critically, more than 80% of the disease-linked variations identified in genome-wide studies are located in the non-coding regions of genomes, especially non-coding RNA, suggesting non-coding RNAs are relevant to disease. Thus, a critical path forward for understanding non-coding RNAs' role, especially long non-coding RNAs, is to understand the genomic regions' transcriptional regulation, especially non-coding regions. Here, we developed a user-friendly R package called SomaGene for studying and identifying enhancer-like non-coding RNAs with enriched somatic mutations in the cancer genome. SomaGene accepts different genomic variants (whole genome/exome somatic point mutations, structural variations, copy number variations) to identify those RNAs that significantly mutated in diseases (e.g., cancer). It then uses multiple publicly available genomics and epigenetics datasets including ENCODE epigenomics annotations, FANTOM5 tissue-specific expression profiles, disease-associated genome-wide association SNPs, and tissue-specific eQTL pairs to identify those RNAs with potentially enhancer function. SomaGene, as a powerful R package, can provide the opportunity to cancer scientists to study the roles of non-coding RNAs in different cancer genomes.

In this article, the usual factorials and binomial coefficients have been generalized and extended to the negative integers. Basing on this generalization and extension, a new kind of polynomials has been proposed, which led directly to the non-classical hypergeometric orthogonal polynomials and the non-classical second-order hypergeometric linear DEs. The resulting polynomials can be used in non-relativistic and relativistic QM, particularly, in the case of the Schrödinger equation, and Dirac equations for an electron in a Coulomb potential field.

Numerical models widely used for hydrocarbon phase behavior and compositional flow simulations are based on assumption of thermodynamic equilibrium. However, it is not uncommon for oil and gas-condensate reservoirs to exhibit essentially non-equilibrium phase behavior, e.g., in the processes of secondary recovery after pressure depletion below saturation pressure, or during gas injection, or for condensate evaporation at low pressures. In many cases the ability to match field data with equilibrium model depends on simulation scale. The only method to account for non-equilibrium phase behavior adopted by the majority of flow simulators is the option of limited rate of gas dissolution (condensate evaporation) in black oil models. For compositional simulations no practical yet thermodynamically consistent method has been presented so far except for some upscaling techniques in gas injection problems. Previously reported academic non-equilibrium formulations have a common drawback of doubling the number of flow equations and unknowns compared to the equilibrium formulation. In the paper a unified thermodynamically-consistent formulation for compositional flow simulations with non-equilibrium phase behavior model is presented. Same formulation and a special scale-up technique can be used for upscaling of an equilibrium or non-equilibrium model to a coarse-scale non-equilibrium model. A number of test cases for real oil and gas-condensate mixtures are given. Model implementation specifics in a flow simulator are discussed and illustrated with test simulations. A non-equilibrium constant volume depletion algorithm is presented to simulate condensate recovery at low pressures in gas-condensate reservoirs. Results of satisfactory model matching to field data are reported and discussed.

GCTs are developmental tumors and likely to reflect ontogenetic and teratogenetic determinants. The objective was to identify syndromes with or without congenital anomalies and non-syndromic defects as potential risk factors. Patients with extracranial GCTs (eGCTs) registered in MAKEI 96/MAHO 98 between 1996 and 2017 were used. According to Teilum's holistic concept malignant and benign teratomas were registered. We used a case control study design with Orphanet as a reference group for syndromic defects and the Mainz birth registry (EUROCAT) for congenital anomalies at birth. Co-occurring genetic syndromes and/or congenital anomalies were assessed accordingly. Odds ratios and 95% confidence intervals were calculated and p-values for Fisher’s exact test with Bonferroni correction if needed. A strong association was confirmed for Swyer (OR 338.6, 95% CI 43.7-2623.6) and Currarino syndrome (OR 34.2, 95% CI 13.2-88.6). We additionally found 17 isolated cases of eGCT with a wide range of syndromes, however not significantly associated following Bonferroni correction. All these cases pertained to girls. Regarding non-syndromic defects, no association with eGCTs could be identified. In our study we confirmed a strong association for Swyer and Currarino syndromes with additional congenital anomalies.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

Despite significant milestones in armed conflict research generally and climate security research specifically, methodologically tight explanation of naturally caused armed conflict still leaves much to be desired. In this article we unpack the black box of the climate-security nexus and advance causal modelling of armed conflict. To infer effects of natural causes on armed conflict outcomes, we apply recent advances in causal methods to conflict outcomes that have been non-experimentally observed across Iraqi municipalities. Retrieval of an entire empirical causal structure of climate-conflict pathways allows us to corroborate the existence of a cause-and-effect relationship between climatological, environmental, and demographic variables and armed conflict. We confirm that soil temperature, population density, and variability of latent energy cause an increase in fatalities, while rice production decreases fatalities. We discuss our findings, their limitations, and future research directions, and reflect on their relevance for policy interventions.

Background: Despite scientific advances, the management of procedural pain in neonates remains suboptimal. Applying adequate therapy to control pain during the neonatal period is a moral and ethical act. In recent decades, ample evidence has accumulated regarding the risks, associated with both untreated pain and the use of more aggressive analgesic therapy. Thus, the emphasis in neonatal clinical practice is on non-aggressive pain management techniques, including homeopathic agents. The efficacy and safety of homeopathic agents for reducing procedural pain in neonates is the subject of the present study. Materials and Methods: Healthy full-term newborn babies with an average age of 72-84 hours were included. They were divided into three study groups: group (A) – not anesthetised, /n= 67/, group (B) – anesthetised with Arnica D30 /n=40/ and group (C)- anesthetised with Sol.Glucose 25% /n=40/. The severity of the pain was assessed using the multimodal - Neonatal Infant Pain Scale (NIPS) and the unimodal - Neonatal Facial Coding System (NFCS) scale. Assessments were done 30s before, 30 seconds after, and 5 minutes after the painful stimulus caused by the heel prick. Heart rate, transcutaneous oxygen saturation, respiratory rate and blood pressure were examined at the same intervals. The results obtained were processed statistically by descriptive analysis and ANOVA at a significance level of p&lt; 0.05. Results: 5 minutes after heel prick both scales showed a statistically significant lower score in those given Arnica D30, compared to those who received Sol.Glucose 25%. When monitoring the physiological indicators, we found a significant increase in the heart rate 30 seconds after the procedure.5 minutes after the heel prick we recorded significantly respiratory rate and systolic blood pressure in all three groups compared to pre-procedural values. Conclusions: Arnica D30 has better analgesic effects compared to Sol.Glucose 25% for newborn babies after heel prick tests.

Approximately 300 million non-cardiac surgeries are performed each year. Perioperative mortality after non-cardiac surgery is estimated at 2% in patients over 45 years of age . Half of these deaths are attributable to cardiovascular complications, and most to perioperative myocardial infarction (MINS). Before introduction of cardiac biomarkers the diagnosis of postoperative myocardial infarction was based on symptoms and electrocardiographic changes and its incidence was largely underestimated. The incidence of MINS when standard troponin assay is used ranges between 8 and 19% but increases to 20-30% whit high sensitivity troponin assays. Higher troponin values sugegsting myocardial injury , both with or without definite diagnosis of myocardial infarction, are associated with increased 30 day and 1-year mortality . Diagnostic and therapeutic strategies are reported .

Malnutrition problems are related to diets that lack one or more essential elements, which it is extremely important to food enrichment to improve the content of compounds effective for health. The objective of this study is to evaluate the effect of the addition of Ca2+, K+ and Mg2+ on the induction of nutraceutical quality in grafted tomatoes grown in the NFT (Nutrient Film Technique) system. In the experiment, two factors were evaluated: plants with and without grafting and the foliar application of 10 ml L−1 Ca2+, 4 ml L−1 K+ and 10 ml L−1 Mg2+ cations separately for each case, in addition to the control. The treatments were evaluated using a completely randomized design, with 5 repetitions per treatment. The interactive effects between grafting and foliar application of Ca2+ induced a greater content lycopene, β-carotene and total flavonoids in fruits of tomato. The interactive effects between the graft and the Mg2+ foliar applications obtained the best results in the phenol content. As regards, capacity DPPH and ABTS, the graft decreased concentration, increasing the content of these through foliar applications of calcium. Regarding the enzymatic variables, graft factor increased activity catalase, glutathione peroxidase and phenylalanine ammonium lyase, obtained the best results graft interaction and foliar application of calcium and magnesium. The results obtained demonstrate the influence of the use of grafts and foliar applications of cal-cium and magnesium as tools that could improve the nutraceutical quality content of tomato crop

Metformin is an oral antidiabetic agent with antimicrobial properties, excreted in an active and unmetabolized form. Like some non-antibiotic drugs, subinhibitory concentrations of metformin may contribute to the expression of microbial resistance in wild-type strains. This work aimed to evaluate the biofilm formation of Pseudomonas aeruginosa TGC04 exposed to 100 and 200 µg/mL of metformin, varying the Chemical Oxygen Demand (COD) and flow regime. Biofilms were quantified after 2 and 24 hours, observing reductions and increases in biofilm growth around 13 and 64%, respectively. The greatest biofilm growth occurred in cells exposed to 200 µg/mL of metformin. Both the flow regime and COD concentration were important for the development of the biofilm, whose cells were mostly weakly to moderately adhered. The study provides evidence that in polluted aquatic systems with turbulent regimes, the inhibitory concentration of metformin promoted the least disturbances to the biofilm.

In this review, we will cover a general overview of the current panorama on lncRNAs with an actual or potential role as biological markers in cancer. We will discuss examples of multi-omics approaches that integrates information on somatic aberrations, gene expression and epigenomics, with the scope of providing a more comprehensive view of the functional impact of lncRNA profiles and how these paradigm can be exploited for the discovery and selection of lncRNAs with a functional role and their use as variables informing on progression and prognostic and help guiding the selection of therapeutic strategies for cancers. Finally, we propose a perspective for future evolution of the study of lncRNAs and the discovery of their functional and harnessing their potential to assist in clinical management of malignancies.

Small bowel non-Meckelian diverticulosis is a rare condition with only few published cases despite being described over 200 years ago. In the midst of the COVID-19 pandemic, studies suggested that a lot of patients may experience gastrointestinal manifestations. Intestinal symptoms could worsen the inflammation and infection associated with small bowel diverticulitis. Here, we present two cases: one with inflammation and rupture in a COVID-19 patient and the other as an asymptomatic detection. Furthermore, we provide a mini-review of the literature to emphasize the importance of considering this entity in the differential diagnosis of an acute abdomen.

This publication delves into the intricate world of human communication, extending beyond the realm of spoken and written language to explore the profound influence of non-verbal communication. Focusing on body language—comprising gestures, facial expressions, postures, and movements—it reveals the pivotal role it plays in conveying emotions, intentions, and psychological states. The rapidly evolving fields of neuroscience and cognitive science are investigating the neural mechanisms and cognitive processes that underpin the interpretation and utilization of these non-verbal cues. Notably, the amygdala's involvement in processing emotional facial expressions has provided a neurological foundation for our emotional understanding in non-verbal communication. Concurrently, cognitive psychology sheds light on how perception, attention, and memory influence our interpretation of non-verbal cues and communication strategies.In our modern, technologically advancing society characterized by global interconnectivity and cultural diversity, the significance of non-verbal communication, especially in digital and virtual contexts, is paramount. The transformation of non-verbal expression into digital symbols like emoticons and emojis raises questions regarding its ability to maintain authenticity and emotional understanding. This publication endeavors to comprehensively explore the fundamental role of body language and non-verbal communication in contemporary society. By integrating insights from psychology, neuroscience, social sciences, and digital technologies, it aims to elucidate the underlying mechanisms guiding non-verbal communication. Additionally, it delves into the implications of non-verbal communication across diverse domains, including interpersonal communication, the workplace, politics, advertising, and the virtual world.The research presented herein strives to offer a thorough understanding of interpersonal dynamics, relationships, and social behavior, with the goal of promoting the development of more effective, conscious, and ethically guided communication strategies. Ultimately, this analysis aspires to inspire further interdisciplinary research and reflection, addressing emerging challenges and fully leveraging the potential of non-verbal communication in modern society. This, in turn, guides our path towards a communication landscape that is more inclusive, authentic, and empathetic.

Although adult spontaneous (non-diabetic) hypoglycaemia is rare, its recognition is important for the preventative or curative treatment of the underlying cause. Establishing Whipple’s triad; low blood glucose, neuroglycopaenia and resolution of neuroglycopaenia on increasing blood glucose levels to normal or above, is essential to verify hypoglycaemia. Awareness that hypoglycaemia may occur in severely ill patients is important for its prevention. Further investigation in such cases is unnecessary unless another cause of hypoglycaemia is suspected. Patients are often asymptomatic and normoglycaemic at review. History of medication, self-medication, access to hypoglycaemic drugs, alcohol and comorbidity may provide aetiological clues. The investigation involves obtaining blood samples during symptoms for laboratory glucose measurement or provoking fasting or postprandial hypoglycaemia as directed by symptoms. If confirmed, insulin, c-peptide, proinsulin, beta-hydroxybutyrate are analysed in hypoglycaemic samples. These will classify hypoglycaemia due to non-ketotic hyperinsulinaemia, non-ketotic hypoinsulinaemia and ketotic hypoinsulinaemia and direct investigations to identify the underlying cause. There are, however, many pitfalls, which may mislabel healthy individuals as “hypoglycaemic” or misdiagnose treatable or preventable causes of spontaneous hypoglycaemia. Clinical acumen and appropriate investigations will mostly identify hypoglycaemia and its cause.

This paper presents ConF, a novel deep learning model designed for accurate and efficient prediction of non-coding RNA families. NcRNAs are essential functional RNA molecules involved in various cellular processes, including replication, transcription, and gene expression. Identifying ncRNA families is crucial for comprehensive RNA research, as ncRNAs within the same family often exhibit similar functionalities. Traditional experimental methods for identifying ncRNA fam-ilies are time-consuming and labor-intensive. Computational approaches relying on annotated secondary structure data face limitations in handling complex structures like pseudoknots and have restricted applicability, resulting in suboptimal prediction performance. To overcome these chal-lenges, ConF integrates mainstream techniques such as residual networks with dilated convolutions and cross multi-head attention mechanisms. By employing a combination of dual-layer convolu-tional networks and BiLSTM, ConF effectively captures intricate features embedded within RNA sequences. This feature extraction process leads to significantly improved prediction accuracy compared to existing methods. Experimental evaluations conducted on a ten-fold publicly available dataset demonstrate the superiority of ConF in terms of accuracy, sensitivity, and other perfor-mance metrics. Overall, ConF represents a promising solution for accurate and efficient ncRNA family prediction, addressing the limitations of traditional experimental and computational methods.