This paper presents a multi-swarm PSO algorithm for the Quadratic Assignment Problem (QAP) implemented on the OpenCL platform. Our work was motivated by results of time efficiency tests performed for single-swarm algorithm implementation that showed clearly that the benefits of a parallel execution platform can be fully exploited provided the processed population is large. The described algorithm can be executed in two modes: with independent swarms or with migration. We discuss the algorithm construction as well as we report results of tests performed on several problem instances from the QAPLIB library. During the experiments the algorithm was configured to process large populations. This allowed us to collect statistical data related to values of goal function reached by individual particles. We use them to demonstrate on two test cases that although single particles seem to behave chaotically during the optimization process, when the whole population is analyzed, the probability that a particle will select a near-optimal solution grows.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

The Multi-Level Model (=MLM) was suggested by A. Levichev as a description of quarks and gluons. The review recalls MLM-terminology while MLM-findings (for quarks and leptons) are compared to the theoretical and experimental data as accepted by the Standard Model (=SM). MLM is based on Segal’s compact space-time U(2) and on the sequence of embeddings: U(2) into U(3), U(2) into U(4), etc. These groups were called the levels (of matter): U(2) - the 0th (that is, our mundane world), U(3) - the 1st, U(4) - the 2nd, etc. Such a convention matches the SM-quarks' generations list. Each SM-quark is viewed either as a sunken proton, or as a captured proton. The MLM-proton is elementary and indestructible (hence no need for confinement). For MLM-quarks, in terms of the notion of a ruling group, flavor and color are defined mathematically. The number of colors (and of flavors) is level-dependent. For levels U(3) through U(6) the correspondence with the SM-quarks is established. Three new quarks and two new leptons are predicted. The SM-puzzle of quark and lepton generations is solved. Using the Han-Nambu scheme, the notion of the quark’s electric charge is expressed in terms of color charges. The original part of the review suggests studying the proton’s properties (like mass, shape and inner pressure) on the ba-sis of its wave function.

The introduction of the Internet of Things (IoT), i.e. the interconnection of embedded devices over the Internet, has changed the world we live in from the way we measure, make calls, print information and even the way we get energy in our offices or homes. The convenience of IoT products, like CCTV cameras, IP phones, and oscilloscopes, is overwhelming for end-users. In parallel, however, security issues have emerged and it is essential for infrastructure providers to assess the associated security risks. In this paper, we propose a novel method to detect IoT devices and identify the manufacturer, device model, and the firmware version currently running on the device using the page source from the web user interface. We performed automatic scans of the large-scale network at the European Organization for Nuclear Research (CERN) to evaluate our approach. Our tools identified 233 IoT devices that fell into eleven distinct device categories and included 49 device models manufactured by 26 vendors from across the world.

Miscanthus holds a great potential in the frame of the bioeconomy and yield prediction can help improving Miscanthus logistic supply chain. Breeding programs in several countries are attempting to produce high-yielding Miscanthus hybrids better adapted to different climates and end-uses. Multispectral images acquired from unmanned aerial vehicles (UAVs) in Italy and in the UK in 2021 and 2022 were used to investigate the feasibility of high-throughput phenotyping (HTP) of novel Miscanthus hybrids for yield prediction and crop traits estimation. An intercalibration procedure was performed using simulated data from the PROSAIL model to link vegetation indices (VIs) derived from two different multispectral sensors. Random forest algorithm estimated with good accuracy yield traits (light interception, plant height, green leaf biomass and standing biomass) using VIs time series and predicted yield using peak descriptor derived from VIs time series with 2.3 Mg DM ha-1 of RMSE. The study demonstrates the potential of UAVs multispectral in HTP applications and in yield prediction for providing important information needed to increase sustainable biomass production.

A Wireless Body Area Sensor Network (WBASN) is combination of numerous sense nodes, positioned onto/close or inside a person body. Wireless Body Area Sensor Networks (WBASN) is a developing automation trend that exploits wireless sensor nodes to put instantaneous wearable well-being of ill person to improve individual’s existence. The sensor nodes might be used outwardly to observe abundant health parameters (like heart activity, blood pressure and cholesterol) of an ill person at a vital site within hospital. Hence the goal of WBASN is much crucial, enhancing the lifetime of nodes is compulsory to sustain many issues such as utility and efficiency. It is essential to evaluate time that when the first node will die it we want to refresh or change the battery reason is that loss of crucial information is not tolerable. The lifetime is termed as the time interval when a first node dies out due to battery exhaustion. In our proposed protocol life time of a network is the main concern as well other protocol related issues such as throughput, path loss, and residual energy. Bio-sensors are used for deployment on human body. Poisson distribution and equilibrium model techniques have been used for attaining the required results. Multi-hop network topology and random network node deployment used to achieve minimum energy consumption and longer network lifetime.

In this study, we examine the relationship of bank level lending and borrowing decisions and the risk preferences on the dynamics of the interbank lending We develop an agent-based model that incorporates individual bank decisions using the temporal difference reinforcement learning algorithm with empirical data of 6600 S. banks. The model can successfully replicate the key characteristics of interbank lending and borrowing relationships documented in the recent literatur A key finding of this study is that risk preferences at individual bank level can lead to unique interbank market structures which are suggestive of the capacity that the market responds to surprising

Acetyleugenol is a phytochemical compound with broad effect against infectious diseases and tumors. Here, we extracted, characterized and elucidated the structure of acetyeugenol, for the first time, from the leaves of Acacia nilotica (L.)―a well-known medicinal plant. The broad antibacterial potential of acetyleugenol was first confirmed against seven bacterial pathogenic isolates with best activity against Proteus sp., Salmonella typhi, Staphylococcu aureus, and Streptococcus pneumonia, which showed similar or better zone of inhibition to that of the control amoxicillin. To further investigate its effect against Mycobacterium tuberculosis, acetyleugenol and its indole and phenyl analogs were subjected to molecular docking experiments against two potential tuberculosis drug targets―MtPknE and MtPknB Ser/Thr protein kinases. The results reveal that all of the analogs have improved docking scores comparing to the acetyleugenol. The indole analogs EUG-1 and EUG-3 were more effective with better docking scores for MtPknE with –11.08 and –10.05 kcal/mol, respectively. Similar results were obtained for the MtPknB. In contrast, only the EUG-2 phenyl analog has given rise to similar docking scores for both targets. This opens the door for further comprehensive studies on these acetyleugenol analogs with in vitro and in vivo experiments to validate and get more insights into their mechanisms of action.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

Clustering algorithms for multi-database mining (MDM) rely on computing $(n^2-n)/2$ pairwise similarities between $n$ multiple databases to generate and evaluate $m\in[1, (n^2-n)/2]$ candidate clusterings in order to select the ideal partitioning which optimizes a predefined goodness measure. However, when these pairwise similarities are distributed around the mean value, the clustering algorithm becomes indecisive when choosing what database pairs are considered eligible to be grouped together. Consequently, a trivial result is produced by putting all the $n$ databases in one cluster or by returning $n$ singleton clusters. To tackle the latter problem, we propose a learning algorithm to reduce the fuzziness in the similarity matrix by minimizing a weighted binary entropy loss function via gradient descent and back-propagation. As a result, the learned model will improve the certainty of the clustering algorithm by correctly identifying the optimal database clusters. Additionally, in contrast to gradient-based clustering algorithms which are sensitive to the choice of the learning rate and require more iterations to converge, we propose a learning-rate-free algorithm to assess the candidate clusterings generated on the fly in a fewer upper-bounded iterations. Through a series of experiments on multiple database samples, we show that our algorithm outperforms the existing clustering algorithms for MDM.

Manufacturing corporations has the acceptance of the Outsourcing Process (OP) to improve industrial activities as well as to archive the revenue objectives, and with this, Risk Analysis (RA) tools are constantly used to assure expected results. Failure Mode and Effect Analysis (FMEA) is one of preferred RA tools, moreover, it is proven that FMEA adds uncertainty because of the human participation at the RA, afterward it is demonstrated that Pythagorean Fuzzy Dimensional Analysis – FMEA – Value Stream Mapping (PFDA-FMEA-VSM) method removes the uncertainty in RA, likewise it aids to the stakeholders for decision making, giving more advantages improving the use of the resources on the project. This document exhibits a real case scenario in a manufacturing firm applying PFDA-FMEA-VSM method adapted for manufacturing OP. The application of PFDA-FMEA-VSM shows solid RA results, removing the human intervention uncertainty added to the risk ranking, gives advantages to the stakeholders for visualize the main risks in detailed diagram, as well as make easier to take better decisions on where to apply resources and mitigate risks during OP.

The growth of demand for metallic minerals has faced with the need for new techniques and improving technologies for all mine life cycle operations. Nowadays, the exploitation of old tailings and mine wastes facilities could represent a solution to this demand, with economic and environmental advantages. W-Sn Panasqueira Mine has been operating for more than 100 years. Its first processing plant “Rio” was located near Zêrere river being the mineral processing residues deposited on the top hillside on the margin of this river in Cabeço do Pião tailings dam. The lack of maintenance and monitoring of this enormous structure in the last twenty years represents high risks to the environment and population of the surrounding region. The re-mining of the tailings by hydrometallurgical methods was considered, in order to satisfy these two enounced conditions - metals demand and environmental risk, aiming for the sale of the metal to pay the environmental intervention. Field samples campaign allowed collecting data and results from laboratory tests driving to use regression optimization. The re-mining solution was studied, taking into account the technical, economic, social, and environmental aspects.

Equality and incomparability multi-label ranking have not been introduced to learning before. This paper proposes new native ranker neural network to address the problem of multi-label ranking including incomparable preference orders using a new activation and error functions and new architecture. Preference Neural Network PNN solves the multi-label ranking problem, where labels may have indifference preference orders or subgroups which are equally ranked. PNN is a nondeep, multiple-value neuron, single middle layer and one or more output layers network. PNN uses a novel positive smooth staircase (PSS) or smooth staircase (SS) activation function and represents preference orders and Spearman ranking correlation as objective functions. It is introduced in two types, Type A is traditional NN architecture and Type B uses expanding architecture by introducing new type of hidden neuron has multiple activation function in middle layer and duplicated output layers to reinforce the ranking by increasing the number of weights. PNN accepts single data instance as inputs and output neurons represent the number of labels and output value represents the preference value. PNN is evaluated using a new preference mining data set that contains repeated label values which have not experimented on before. SS and PS speed-up the learning and PNN outperforms five previously proposed methods for strict label ranking in terms of accurate results with high computational efficiency.

proposal for a fundamental theory is described in which classical and quantum physics as a representation of the universe as a gigantic dendrogram are unified. The latter is the explicate order structure corresponding to the purely number-theoretical implicate order structure given by p-adic numbers. This number field was zero-dimensional, totally disconnected, and disordered. Physical systems (such as electrons, photons) are sub-dendrograms of the universal dendrogram. Measurement process is described as interactions among dendrograms; in particular, quantum measurement problems can be resolved using this process. The theory is realistic, but realism is expressed via the the Leibnitz principle of the Identity of Indiscernible. The classical-quantum interplay is based on the degree of indistinguishability between dendrograms (in which the ergodicity assumption is removed). Depending on this degree, some physical quantities behave more or less in a quantum manner (versus classic manner). Ideologically, our theory is very close to Smolin’s dynamics of difference and Rovelli’s relational quantum mechanics. The presence of classical behavior in nature implies a finiteness of the Universe-dendrogram. (Infinite Universe is considered to be purely quantum.) Reconstruction of events in a four-dimensional space type is based on the holographic principle. Our model reproduces Bell-type correlations in the dendrogramic framework. By adjusting dendrogram complexity, violation of the Bell inequality can be made larger or smaller.

Nisin, an antibacterial compound produced by Lactococcus lactis strains, has been approved by the US Food and Drug Administration to be used as a safe food additive to control the growth of undesirable pathogenic bacteria. Nisin is commonly described as a pH-dependent primary metabolite, since its production depends on growth and culture pH evolution. However, the relationship between bacteriocin synthesis and the consumption of the limiting nutrient has not been described until now. Therefore, this study aimed to develop a competitive four-dimensional Lotka Volterra-like equation to describe the relationships between culture pH, limiting nutrient (total nitrogen: TN) consumption and production of biomass (X) and nisin (BT) in four series of batch fermentation with L. lactis CECT 539 in diluted whey (DW)-based media. The developed four-dimensional LV-like equation (with a unique set of parameters) could not be used to describe all cultures belonging to each fermentation series. However, the four-dimensional LV-like equation described accurately each individual culture, providing a good description of the relationships between pH, TN, X and BT, higher values for R2 and F-ratios, lower values (< 10%) for the mean relative percentage deviation modulus, with bias and accuracy factor values approximately equal to one.

Most existing cancer therapies negatively affect normal tissue as well as cancerous tissue. A potentially effective strategy for treating cancer that precludes off-target damage and could be an option for most patients would involve targeting one or more mutations that are ubiquitous in the given patient’s tumor(s). To effect this strategy, one would employ multi-region sequencing of a patient’s primary tumor and metastases to seek out mutations that are shared between all or at least most regions. Once the target or targets are known, one would ideally rapidly generate a molecular switch for at least one of said ubiquitous mutations that can distinguish the mutated DNA, RNA, or protein from the wild-type version and subsequently trigger a therapeutic response. I propose that the therapeutic response involve the replication of an oncolytic virus or intracellular bacterium, as any mutation can theoretically be detected by a vector that enters the cell - and automatic propagation could be very helpful. Moreover, the mutation “signal” can be easily enhanced through transcriptional and translational (if the target is an intracellular protein) enhancement. Importantly, RNA may make the best target for the molecular switches in terms of amplification of the signal and ease of targeting.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

Deep learning classification is the state-of-the-art of machine learning approach. Earlier work proves that the deep convolutional neural network has successfully and brilliantly in different applications such as images or video data. Recognizing and clarifying the remote sensing aspect of the earth's surface and exploit land cover and land use (LCLU). First, this article summarized the remote sensing emerging application and challenges for deep learning methods. Second, we propose four approaches to learn efficient and effective CNNs to transfer image representation on the ImageNet dataset to recognize LCLU datasets. We use VGG16, Inception-ResNet-V2, Inception-V3, and DenseNet201 models to extract features from the EACC dataset. We use pre-trained CNNs on ImageNet to extract features. For feature selection we proposed principal component analysis (PCA) to improve accuracy and speed up the model. We train our model by multi-layer perceptron (MLP) as a classifier. Lastly, we apply the multi-granularity encoding ensemble model. We achieve an overall accuracy of 92.3% for the nine-class classification problem. This work will help remote sensing scientists understand deep learning tools and apply them in large-scale remote sensing challenges

In daily travel and activities, pathfinding is a significant process. They are often used in transportation routes calculation. They have now evolved to be able to solve most situations of the pathfinding and its related problems. This review describes previous and recent studies on the pathfinding algorithms. It reviews the development of pathfinding algorithms in a classification base on their usage. The aim is to summarize the application of the pathfinding algorithms for the readers interested in the subject that can be used as a supplement.

In this paper, precise examination of multi-port antennas with large mutual coupling between the ports is studied. For this purpose, some vital parameters such as active reflection coefficients and realised gain are emphasized. The main motivation of this research is the ignorance of this issue in several recently published papers. Hence, corrections and criticisms to some recently reported results are presented. At first, a microstrip patch consisting of two inverted U-slots is re-examined, which has been proposed in a recently published paper for wideband applications. However, the authors did not present satisfactory results to indicate the performance of the proposed structure. In reverse, some important parameters such as the antenna gain appear to be incorrectly reported. In this paper, the characteristics of the antenna are compared with a simple 50 Ω microstrip line excited by two probes, indicating no significant differences. In the remainder of this paper, some corrections are provided on two examples of wide-beam circularly polarised multi-fed antennas for satellite applications. The first example is the multi-fed spiral antennas with folded arms, which have been proposed as the widebeam antennas at 435 MHz. It is indicated that the antenna height should be increased for better performance. The second example is the quadrifilar square helical antennas with folded arms, which have been proposed as the widebeam antennas for 435 MHz with minor responses at 145 MHz. Some corrections are presented on the previously reported minor responses at 145 MHz.

Cumulative exposure to multiple early life stressors are expected to affect behavioral development causing increased susceptibility towards neuropsychiatric disorders. The present study was designed to mimic such conditions in rat model to study behavioral impairments during adolescence and adulthood. Female Wistar rats (n=32; 140-150 gm) were switched to low protein (LP; 8% protein) or Control (20% protein) diet, 15 days prior to conception and then diet regime was maintained throughout the experimental period. Pups born to Control and LP dams were intraperitoneally injected with deltamethrin (DLT-pyrethroid insecticide; 0.7mg/kg body weight; PND 1 to 7) or lipopolysaccharide (LPS-bacterial endotoxin; 0.3mg/kg body weight; PND 3 and 5) or DLT+LPS, on designated days forming 8 experimental groups (Control, LP, Control+LPS, LP+LPS, Control+DLT, LP+DLT, Control+DLT+LPS and LP+DLT+LPS). Neurobehavioral assessments were performed in F1 rats (1, 3, 6 months) by Open field, Elevated plus maze, Light and Dark box, and Rotarod tests. LP rats were found to be more susceptible to either singular or cumulative exposure as compared to their age matched control counterparts, showing significantly severe behavioural abnormalities, as hyperactivity, attention deficits, impulsiveness and low anxiety, the hallmark symptoms of neuropsychiatric disorders like schizophrenia and ADHD, suggesting thereby that early life multi-hit exposure may predispose individuals to developmental disorders.

Multi-criteria decision-making (MCDM) methods and techniques have been applied to many real-world problems in different fields of engineering science and technology. The evaluation based on distance from average solution (EDAS) method is a new and efficient MCDM method. The aim of this study is to propose a modification to address two exceptional cases in which the EDAS method fails to solve an MCDM problem.

A heterogeneous disease like cancer is activated through multiple pathways and different perturbations. Depending upon the activated pathway(s), patients’ survival vary significantly and show different efficacy to various drugs. Therefore, cancer subtype detection using genomics level data is a significant research problem. Subtype detection is often a complex problem, and in most cases, needs multi-omics data fusion to achieve accurate subtyping. Different data fusion and subtyping approaches have been proposed, such as kernel-based fusion, matrix factorization, and deep learning autoencoders. In this paper, we compared the performance of different deep learning autoencoders for cancer subtype detection. We performed cancer subtype detection on four different cancer types from The Cancer Genome Atlas (TCGA) datasets using four autoencoder implementations. We also predicted the optimal number of subtypes in a cancer type using the silhouette score. We observed that the detected subtypes exhibit significant differences in survival profiles. Furthermore, we also compared the effect of feature selection and similarity measures for subtype detection. To evaluate the results obtained, we selected the Glioblastoma multiforme (GBM) dataset and identified the differentially expressed genes in each of the subtypes identified by the autoencoders; the obtained results coincide well with other genomic studies and can be corroborated with the involved pathways and biological functions. Thus, it shows that the results from the autoencoders, obtained through the interaction of different datatypes of cancer, can be used for the prediction and characterization of patient subgroups and survival profiles.

Continuous and emerging advances in Information and Communication Technology (ICT) have enabled IoT-to-Cloud applications to be induced by data pipelines coupled with Edge Intelligence-based architectures. Advanced vehicular networks greatly benefit from these architectures due to the implicit functionalities that are focused on realizing the Internet-of-Vehicle (IoV) vision. However, IoV is susceptible to attacks, where adversaries can easily exploit existing vulnerabilities. Several attacks may succeed due to inadequate or weaker authentication techniques. Hence, there is a timely need for hardening the authentication process through cutting-edge access control mechanisms. This paper proposes a Blockchain-based Multi-Factor authentication model that uses an embedded Digital Signature (MFBC_eDS) for vehicular clouds and Cloud-enabled IoV. Our proposed MFBC_eDS model consists of a scheme that integrates the Security Assertion Mark-up Language (SAML) to the Single Sign-On (SSO) capabilities for a connected Edge-to Cloud ecosystem. MFBC_eDS draws an essential comparison with the baseline authentication scheme suggested by Karla and Sood. Based on the foundations of Karla and Sood’s scheme, an embedded Probabilistic Polynomial-Time Algorithm (ePPTA) and an additional Hash function for the Pi generated during Karla and Sood’s authentication are proposed and discussed. The preliminary analysis of the proposition shows that the approach is more suitable to counter major adversarial attacks in an IoV-centered environment based on Dolev-Yao adversarial model while satisfying aspects of the CIA triad.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

Underwater Wireless Sensor Networks (UWSN) enables various oceanic applications which require effective packet transmission. In this case, sparse node distribution, dynamic network topology and inappropriate selection of relay nodes cause void holes. Addressing this problem, we present a Relay based Void Hole Prevention and Repair protocol (ReVOHPR) by multiple Autonomous Underwater Vehicles (AUV) for UWSN. ReVOHPR efficiently identifies and avoids void holes and trap relay nodes to avoid it. ReVOHPR adopts the following operations as Ocean Depth (levels) based Equal Cluster Formation, Dynamic Sleep Scheduling, Virtual Graph based Routing, and Relay Assisted Void Hole Repair. For energy efficient cluster forming, Entropy based Eligibility Ranking (E2R) is presented which elects stable cluster heads (CHs). Then, dynamic sleep scheduling is implemented Dynamic Kernel Kalman Filter (DK2F) algorithm in which Sleep and Active modes based on the nodes current status. Inter Cluster Routing is performed by maximum matching nodes which selects by Dual criteria and also data transmitted to AUV. Finally, void holes are detected and repair by Bi-Criteria Mayfly Optimization (BiCMO) algorithm. The BiCMO focuses on reducing the number of holes, data packet loss and maximizes Quality of Service (QoS) and energy efficiency of the networks. This protocol is timely deal with node failures in packet transmission via multi-hop routing. Simulation is implemented by NS3 (AquaSim module) simulator that evaluates the performance in network simulation for following metrics as average energy consumption, delay, packet delivery rate and throughput.

The dimensional effect of the accumulation of an electric charge with a density of up to 270 μF/g by the system of compacted zirconium dioxide nanoparticles during exposure in an electric field (5000 V/m) under normal physical conditions is determined. Based on a qualitative complex analysis of the forms of appearance of the effect, it is shown that the place of localization of different charge carriers is the surface of nanoparticles. The supposed mechanism of this effect is considered using the theory of dispersed systems, the band theory, and the theory of contact phenomena in semiconductors. It was concluded that this mechanism is due to the phenomenon of localization of electron-type charge nanoparticles in the near-surface zone of the material in contact with the adsorption ion atmosphere. This effect is relevant for modern nanoelectronics, microsystem technology, and printed electronics.

In the oil palm industry, stands age is an important parameter to monitor the sustainability of cultivation, to develop the growth yield model, to identify the disease or stressed area, and to estimate the carbon storage capacity. This research is focused to estimate and distinguish oil palm stands age based on crown/ canopy density obtained using Forest Canopy Density (FCD) model derived from four indices as follows; Advanced Vegetation Index, Bare Soil Index, Shadow Index, and Thermal Index. FCD model employs multi temporal image analysis resulting four classes of oil palm stands age categorized as seed with FCD value of 29–56% (0 years), young with FCD value of 56–63% (1–9 years), teen with FCD value of 63–80% (10–15 years), and mature with FCD value of >80% (>15 years). Minimum canopy density value is 29% even in the zero years old indicates incomplete land clearance or the type of seed planted in the land.

The interaction between single or a fixed number of photons with a single absorber is of fundamental interest in quantum technology. The harnessing of light matter interactions at the single particle limit has several potential applications ranging from quantum communication and quantum metrology to quantum imaging. In this letter, a setup for heralded two-photon absorption at the single absorber level is proposed. The setup is based on a heralded two-photon source utilizing spontaneous parametric down-conversion, entanglement swapping and sum frequency generation for joint detection. The feasibility of the scheme is discussed by reviewing recent achievements in utilizing entangled and correlated photons for two-photon absorption as well as single photon absorption experiments at the limit of single absorbers in the context of applications in imaging (here mainly microscopy) and spectroscopy.

With quick improvement in the field of network, everything becomes online. Remote user authentication is a mechanism in which remote server verify the correctness of user over common or public channel. Remote user authentication can be Single server authentication or Multi server authentication. The disadvantage of single server authentication is that the user needs to recall user id and password for each service, he/she need to utilize, however it can overcome by Multi-server authentication in which user needs to register himself with Registration Center (RC) for the first run through and after that onwards he can utilize each service (which are given by servers, associated with RC) by recollecting only one user id and password. In this paper, we analyze Chen's authentication scheme (based on multi server authentication) and show that this scheme is vulnerable to password guessing attack, replay attack, RC spoofing attack, session key verification attack and perfect forward secrecy attack. In this Paper, we propose a biometric based remote user authentication scheme in multi-server environment. Proposed scheme is more secure and efficient as compared to chen's scheme\cite{23}.

The Pythagorean fuzzy set (PFS), which is characterized by a membership and a non-membership degree and the square sum of them is less or equal to one, can act as an effective tool to express decision makers’ fuzziness and uncertainty. Considering that the Heronian mean (HM) is a powerful aggregation operator which can take the interrelationship between any two arguments, we study the HM in Pythagorean fuzzy environment and propose new operators for aggregating interval-valued Pythagorean fuzzy information. First, we investigate the HM and geometric HM (GHM) under interval-valued intuitionistic fuzzy environment and develop a series of aggregation operators for interval-valued intuitionistic fuzzy numbers (IVIFNs) including interval-valued intuitionistic fuzzy Heronian mean (IVIFHM), interval-valued intuitionistic fuzzy geometric Heronian mean (IVIFGHM), interval-valued intuitionistic fuzzy weighted Heronian mean (IVIFWHM) and interval-valued intuitionistic fuzzy weighted geometric Heronian mean (IVIFWGHM). Second, some desirable and important properties of these aggregation operators are discussed. Third, based on these aggregation operators, a novel approach to multi-attribute decision making (MADM) is proposed. Finally, to demonstrate the validity of the approach, a numerical example is provided and discussed. Moreover, we discuss several real-world applications of these operators within policy-making contexts.

This study aims to develop a performance evaluation system that can facilitate performance evaluation at region, hospital, and department levels to enable better cost management for sustainable development. A multi-level system of performance evaluation informs a hierarchical assessment of cost management from regions to hospitals to departments using diagnosis-related group (DRGs). Various metrics are developed employing the variances between targets and actuals where targets are determined from two perspectives: benchmarking using external regional prices and change management using internal data. Targets for the latter are statistically based and specifically incorporate variability. The model is applied to two hospitals, twenty departments, nine DRGs and 1071 inpatients. The analyses indicate that the approach can provide a practical evaluation tool that allows for particular characteristics at multiple levels. The system provides macro-micro and external-internal perspectives in performance, enabling high-level variances to be decomposed thereby identifying sources of performance variability and financial impact.

A multi-decadal change analysis of the irrigation ponds in Taoyuan, Taiwan was conducted by using multi-source data including digitized ancient maps, declassified single-band CORONA satellite images, and multispectral SPOT images. Supervised LULC classifications were conducted using four textural features derived from the single-band CORONA images and spectral features derived from SPOT images. Post-classification analysis revealed that the number of irrigation ponds in the study area decreased during the post-World War II farmland consolidation period (1945 – 1965) and the subsequent industrialization period (1970 – 2000). However, efforts on restoration of irrigation ponds in recent years have resulted in gradual increases in the number (9%) and total area (12%) of irrigation ponds in the study area.

We extended the usage of the expansion method based on Sine-Gordon equation to the two dimensional Fisher equation. The relation between the trigonometric and hyperbolic functions are derived from the Sine-Gordon equation dened in two space dimension. The complex-valued traveling wave solutions to the two dimensional Fisher and Nagumo equations are set in forms a nite series of multiplications of powers of sech(.) and tanh(.) functions.

Sustainability in material purchasing is a growing area of research. Goods purchasing decisions strongly affect transportation path flows, vehicle consolidation, inventory levels and related obsolescence costs. Within a global sourcing context, companies experience the need of new decision making approaches capable to consider a large variety of factors, also linked with society and environment. Environmental impact assessment has become a key requirement for materials purchasing and transportation decisions since global warming is a rising concern both in academic and industrial researches. In fact, it is well known that the freight transport industry is responsible for large amounts of carbon emissions contributing to global warming. In this paper, we initially analyse and compare the environmental economic policies established by the International Governments in relation to the carbon trading systems adopted. Then, we develop a multi-objective lot sizing approach useful in practice to define the sustainable quantity to purchase when a Cap and Trade mitigation policy is present. We further analyse the model behaviour according to different carbon price values by demonstrating that carbon prices are still far too low to motivate managers towards sustainable purchasing choices.

The hybrid system is analyzed and optimized to produce electric energy in Non-Interconnected Zones in the Colombian Caribbean region, contributing both to the improvement in the reduction of greenhouse gas emissions and to the rational use of energy. A comparative analysis of the performance of these systems was carried using a dynamic model in real wind and solar data. The model is integrated by a Southwest Wind Power Inc. wind turbine. AIR 403, a proton exchange fuel cell (PEM), an electrolyze, a solar panel and a charge regulator based on PID controllers to manipulate oxygen and hydrogen flows in the cell. The transient responses of the cell voltage, current, and power were obtained for the demand of 200 W for changes in solar radiation and wind speed for all days of the year 2013 in the Ernesto Cortissoz airport, Puerto Bolívar, Alfonso Lopez airport and Simon Bolívar airport, by regulating the flow of hydrogen and oxygen into the fuel cell. The maximum contribution of power generation from the fuel cell was presented for the Simon Bolívar airport in November with a value of 158,358W (9.45%). A multi-objective design optimization under a Pareto front is presented for each place studied to minimize the Levelized Cost of Energy and CO₂ emission, where the objective variables are the number of panel and stack in the PV system and PEM.

Geometric Akaike Information Criteria (G-AICs) for generalized noise-level dependent crystallographic symmetry classifications of two-dimensional (2D) images that are more or less periodic in either two or one dimensions as well as Akaike weights for multi-model inferences and predictions are reviewed. Such novel classifications do not refer to a single crystallographic symmetry class exclusively in a qualitative and definitive way. Instead, they are quantitative, spread over a range of crystallographic symmetry classes, and provide opportunities for inferences from all classes (within the range) simultaneously. The novel classifications are based on information theory and depend only on information that has been extracted from the images themselves by means of maximal likelihood approaches so that these classifications are objective. This is in stark contrast to the common practice whereby arbitrarily set thresholds or null hypothesis tests are employed to force crystallographic symmetry classifications into apparently definitive/exclusive states, while the geometric feature extraction results on which they depend are never definitive in the presence of generalized noise, i.e. in all real world applications. Thus, there is unnecessary subjectivity in the currently practiced ways of making crystallographic symmetry classifications, which can be overcome by the approach outlined in this review.

The Finite size Lyapunov exponent (FSLE) has been used extensively since the late 1990’s to diagnose turbulent regimes from Lagrangian experiments and to detect Lagrangian coherent structures in geophysical flows and two-dimensional turbulence. Historically, the FSLE was defined in terms of its computational method rather than via a mathematical formulation, and the behavior of the FSLE in the turbulent inertial ranges is based primarily on scaling arguments. Here we propose an exact definition of the FSLE based on conditional averaging of the finite amplitude growth rate (FAGR) of the particle pair separation. With this new definition, we show that the FSLE is a close proxy for the inverse structural time, a concept introduced a decade before the FSLE. The (in)dependence of the FSLE on initial conditions is also discussed, as well as the links between the FAGR and other relevant Lagrangian metrics, such as the finite time Lyapunov exponent and the second order velocity structure function.

With the latest advances in information and communication technologies, greater amounts of sensitive user and corporate information are constantly shared across the network making it susceptible to an attack that can compromise data confidentiality, integrity and availability. Intrusion Detection Systems (IDS) are important security mechanisms that can perform a timely detection of malicious events through the inspection of network traffic or host-based logs. Throughout the years, many machine learning techniques have proven to be successful at conducting anomaly detection but only a few considered the sequential nature of data. This work proposes a sequential approach and evaluates the performance of a Random Forest (RF), a Multi-Layer Perceptron (MLP) and a Long-Short Term Memory (LSTM) on the CIDDS-001 dataset. The resulting performance measures of this particular approach are compared with the ones obtained from a more traditional one, that only considers individual flow information, in order to determine which methodology best suits the concerned scenario. The experimental outcomes lead to believe that anomaly detection can be better addressed from a sequential perspective and that the LSTM is a very reliable model for acquiring sequential patterns in network traffic data, achieving an accuracy of 99.94% and a f1-score of 91.66%.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

Urgent environmental challenges and emerging additive manufacturing (AM) technologies push research towards more performant and new materials. In the field of metallurgy, high entropy alloys (HEAs) have recently represented a topic of intense research because of their promising properties, such as high temperature strength and stability. Moreover, this class of multi-principal element alloys (MPEAs) have opened up researcher community to unexplored compositional spaces, making prosper literature of high-throughput methodologies and tools for rapidly screening large number of alloys. However, none of the methods has been aimed to design new MPEAs for AM process known as selective laser melting (SLM) so far. Here we conducted nanoindentation testing on single scan tracks of elemental powder blends and pre-alloyed powders after ball milling of AlTiCuNb and AlTiVNb. Results show that nanoindentation can represent an effective technique to gain information about phase evolution during laser scanning, contributing to accelerate the development of new MPEAs.

With the development of satellite load technology and very-large-scale integrated (VLSI) circuit technology, on-board real-time synthetic aperture radar (SAR) imaging systems have facilitated rapid response to disasters. Limited by severe size, weight, and power consumption constraints, a key challenge of on-board SAR imaging system design is to achieve high real-time processing performance. In addition, with the rise of multi-mode SAR applications, the reconfiguration of the on-board processing system is beginning to receive widespread attention. This paper presents a multi-mode SAR imaging chip with SoC architecture based on the reconfigurable double-operation engines and multilayer switching network. We decompose the commonly used extend chirp scaling (CS) SAR imaging algorithm into 8 types of double-operation engines according to the computing orders, and design a three-level switching network to connect these engines for data transition. The CPU is responsible for engine scheduling based on data flow driven with instructions to implement each part of the CS algorithm. Thus, multi-mode floating-point SAR imaging processing can be integrated into a single Application-Specific Integrated Circuit (ASIC) chip instead of relying on distributed technologies. As a proof of concept, a prototype measurement system with chip-included board is implemented, and the performance of the proposed design is demonstrated on Chinese Gaofen-3 stripmap continuous imaging. A chip requires 9.2 s, 50.6 s and 7.4 s for a stripmap with 16,384×16,384 granularity, multi-channel stripmap with 65.536×8192 granularity and multi-channel scan mode with 32,768×4096 granularity and 6.9 W for the system hardware to process the SAR raw data.

Water covers a greater part of the earth's surface. Even though we know very little about the underwater world as most parts of it remain unexplored. Oceans including other water bodies hold huge natural resources and also the aquatic lives. These are mostly unexplored and very few of those are known due to unsuited and hazardous environments for the human to explore. This vast underwater world can be monitored remotely from a distant location with much ease and less risk. To monitor water-bodies remotely in real-time, sensor networking has been playing a great role. It is needed to deploy a wireless sensor network over the volume which we want to surveil. For vast water bodies like oceans, rivers and large lakes, data is collected from the different heights of the water level which is sent to the surface sink. Unlike terrestrial communication, radio waves and other conventional mediums can't serve the purpose of underwater communication as they pose high attenuation and very reduced transmission range. Rather an acoustic medium can transmit data more efficiently and reliably in comparison to other mediums. To transmit data reliably from the bottom of the sea to the sinks at the surface, multi-hop communication is needed which must involve a certain scheme. For seabed to surface sink communication, leading researchers have proposed different routing protocols. The goal of these routing protocols is to make underwater communication more reliable, energy-efficient and delay efficient thus to improve the performance of the overall communication. This paper surveys the advancement and applications of the routing protocols which eventually helps in finding the most efficient routing protocol for the Underwater Wireless Sensor Network (UWSN).

Digital Elevation Models (DEMs) are widely used in geographic and environmental studies. In the current work, the fusion of multi-source DEMs is investigated to improve the overall accuracy of public domain DEMs. Multi-scale decomposition is an important analytical method in data fusion. Three multi-scale decomposition methods – the wavelet transform (WT), bidimensional empirical mode decomposition (BEMD) and nonlinear adaptive multi-scale decomposition (N-AMD) - are applied to the 1-arc-second Shuttle Radar Topography Mission Global digital elevation model (SRTM-1 DEM) and the Advanced Land Observing Satellite World 3D – 30 m digital surface model (AW3D30 DSM) in China. Of these, the WT and BEMD are popular image fusion methods. A new approach for DEM fusion is developed using N-AMD (which is originally invented to remove the cycle from sunspots). Subsequently, a window-based rule is proposed for the fusion of corresponding frequency components obtained by these methods. Quantitative results show that N-AMD is more suitable for multi-scale fusion of multi-source DEMs, taking the ice cloud and land elevation satellite (ICESat) global land surface altimetry data as a reference. The vertical accuracy of the fused DEM shows significant improvements of 29.6% and 19.3% in a mountainous region and 27.4% and 15.5% in a low-relief region, compared to the SRTM-1 and AW3D30 respectively. Furthermore, a slope position-based linear regression method is developed to calibrate the fused DEM for different slope position classes, by investigating the distribution of the fused DEM error with topography. The results indicate that the accuracy of the DEM calibrated by this method is improved by 16% and 13.6%, compared to the fused DEM in the mountainous region and low-relief region respectively, proving that it is a practical and simple means of further increasing the accuracy of the fused DEM.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

Physical frailty and sarcopenia (PF&S) are hallmarks of aging that share a common pathogenic background. Perturbations in protein/amino acid metabolism may play a role in the development of PF&S. In this preliminary study, 68 community-dwellers aged 70 years and older, 38 with PF&S and 30 non-sarcopenic, non-frail controls (nonPF&S), were enrolled. A panel of 37 serum amino acids and derivatives was assayed by UPLC-MS. Partial Least Squares Discriminant Analysis (PLS-DA) was used to characterize the amino acid profile of PF&S. The optimal complexity of the PLS-DA model was found to be three latent variables. The proportion of correct classification was 76.6 ± 3.9% (75.1 ± 4.6% for enrollees with PF&S; 78.5 ± 6.0% for controls). Older adults with PF&S were characterized by higher levels of asparagine, aspartic acid, citrulline, ethanolamine, glutamic acid, sarcosine, and taurine. The profile of nonPF&S individuals was defined by higher levels of α-aminobutyric acid and methionine. Distinct profiles of circulating amino acids and derivatives characterize older individuals with PF&S. The dissection of these patterns may provide novel insights into the role played by protein/amino acid perturbations in the disabling cascade and possible new targets for interventions.

An interesting anomaly of the diffusion process with an apparently negative diffusion coefficient defined through the mean-square displacement in a one-dimensional quantum molecular chain model is shown. Nevertheless, the system satisfies the H-theorem, so that the second law of thermodynamics is satisfied. The reason why the “diffusion constant” becomes negative is due to the effect of the phase mixing process, which is a characteristic result of the one-dimensionality of the system. We illustrate the situation where this negative “diffusion constant” appears.

Landing is one of the most dangerous tasks in all the operations on the aircraft carrier, and the landing safety is very important to the pilot and the flight deck operation. The problem of landing path selection is studied in this paper as there several candidates corresponding to different situations. A fuzzy path selection strategy is proposed to solve the problem considering the fuzziness of environmental information and human judgment, and the goal is to provide the pilot with more reasonable decision. The strategy is based on Fuzzy Multi-attribute Group Decision Making (FMAGDM), which has been widely used in industry. Firstly, the background of the path selection problem is given. Then the essential elements of the problem are abstracted to build the conceptual model. A group decision-making method is applied to denote the preference of each decision maker for each alternative route, and the optimal landing path under the current environment is determined taking into account the knowledge and the weight of both decision makers. Experimental studies under different setups, i.e., different environments, are carried out. The results demonstrate that the proposed path selection strategy is validated in different environments, and the optimal landing paths corresponding to different environments can be determined.

Exploiting the linguistic knowledge of the source language for neural machine translation (NMT) has recently achieved impressive performance on many large-scale language pairs. However, since the Turkish→English machine translation task is low-resource and the source-side Turkish is morphologically-rich, there are limited resources of bilingual corpora and linguistic information available to further improve the NMT performance. Focusing on the above issues, we propose a multi-source NMT approach that models the word feature in parallel to external linguistic features by using two separate encoders to explicitly incorporate linguistic knowledge into the NMT model. We extend the word embedding layer of the knowledge-based encoder to accommodate for each word’s linguistic annotations in the context. Moreover, we share all parameters across encoders to enhance the representation ability of the NMT model on the source language. Experimental results show that our proposed approach achieves substantial improvements of up to 2.4 and 1.1 BLEU scores in Turkish→English and English→Turkish machine translation tasks, respectively, which points to a promising way to utilize the source-side linguistic knowledge for the low-resource NMT.

This study aims to examine the impact of tablet use on preschoolers’ executive function during the Dimensional Change Card Sort Task (DCCS) task using the functional near-infrared spectroscopy (fNIRS). Altogether 38 Chinese preschoolers (Mage = 5.0 years, SD = 0.69 years, 17 girls) completed the tasks before the COVID-19 lockdown. Eight children never used tablets, while 16 children were diagnosed as the ‘heavy-user'. The results indicated that: (1) the 'Non-user' outperformed the 'Heavy-user' with a significantly higher correct rate in the DCCS task; (2) the two groups differed significantly in the activation of the prefrontal cortex (BA 9): the 'Non-user' pattern is normal and healthy, whereas the 'Heavy-user' pattern is not normal and needs further exploration.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

Recent advancements of computer and electronic systems have motivated the extensive use of intelligent systems for automation of agricultural industries. In this study, the temperature variation of the mushroom growing room is modeled through using a multi-layered perceptron (MLP) and radial basis function networks. Modeling has been done based on the independent parameters including ambient temperature, water temperature, fresh air and circulation air dampers, and water tap. According to the obtained results from the networks, the best network for MLP is found to be the second repetition with 12 neurons in the hidden layer and 20 neurons in the hidden layer for radial basis function networks. The obtained results from comparative parameters for two networks showed the highest correlation coefficient (0.966), the lowest root mean square error (RMSE) (0.787) and the lowest mean absolute error (MAE) (0.02746) for radial basis function. Therefore, the neural networks with radial basis function was selected as the optimal predictor for the behavior of the system.

We propose a probabilistic graphical model for discriminative substrate characterization, to support geological and biological habitat mapping in aquatic environments. The model, called a fully connected conditional random field (CRF), is demonstrated using multispectral and monospectral acoustic backscatter from heterogeneous seafloors in Patricia Bay, British Columbia, and Bedford Basin, Nova Scotia. Unlike previously proposed discriminative machine learning algorithms, the CRF model considers both the relative backscatter magnitudes of different substrates and their relative proximities. The model therefore combines the statistical flexibility of a machine learning algorithm with an inherently spatial treatment of the substrate. The CRF model predicts substrates such that nearby locations with similar backscattering characteristics are likely to be in the same substrate class. The degree of proximity and allowable backscatter similarity are controlled by parameters that are learned from the data. CRF model results were evaluated against a popular generative model known as a Gaussian Mixture model that doesn't include spatial dependencies, only covariance between substrate backscattering response over different frequencies. Both models are used in conjunction with sparse bed observations/samples in a supervised classification. A detailed accuracy assessment, including a leave-one-out cross-validation analysis, was performed using both models. Using multispectral backscatter, the GMM model trained on 50% of the bed observations resulted in a 75% and 89% average accuracies in Patricia Bay and Bedford Basin, respectively. The same metrics for the CRF model were 78% and 95%. Further, the CRF model resulted in a 91% mean cross-validation accuracy across four substrate classes at Patricia Bay, and a 99.5% mean accuracy across three substrate classes at Bedford Basin, which suggest that the CRF model generalizes extremely well to new data. This analysis also showed that the CRF model was much less sensitive to the specific number and locations of bed observations than the generative model, owing to its ability to incorporate spatial autocorrelation in substrates. The CRF approach therefore may prove to be a powerful `spatially aware' alternative to other discriminative classifiers.

Protein is the proteios building block of life. Evolutionarily, its sequence is not as conserved as its structure, making it more reasonable for protein structure, instead of protein sequence, to be the descriptor of protein function. Yet, in the National Center for Biotechnology Information (NCBI) database, the number of experimentally identified protein sequences is in great excess of that of experimentally determined protein structures inside the almost-half-a-century old Protein Data Bank (PDB). For instance, GPR151 is an proton-sensing G-protein coupled receptor (GPCR) originally identified as homologous to galanin receptors. As of March 19, 2020, GPR151’s structure has not been experimentally determined and deposited in PDB yet. Thus, an ab initio modelling approach was employed here to build a three-dimensional structure of GPR151. Overall, the ab initio GPR151 model presented herein constitutes the first structural hypothesis of GPR151 to be experimentally tested in future with previously published, currently ongoing and future GPR151 studies.

UAS-based multi-spectral imagery is becoming increasingly popular for the improved monitoring and managing of various horticultural crops. However, for UAS data to be used as an industry standard for assessing tree structure and condition as well as production parameters, it is imperative that the appropriate data collection and pre-processing protocols are established to enable multi-temporal comparison. There are several UAS-based radiometric correction methods commonly used for precision agricultural purposes. However, their relative accuracies have not been assessed for data acquired in complex horticultural environments. This study assessed the variations in estimated surface reflectance values of different radiometric corrections applied to multi-spectral UAS imagery acquired in both avocado and banana orchards. We found that inaccurate calibration panel measurements, inaccurate signal-to-reflectance conversion, and high variation in geometry between illumination, surface, and sensor viewing produced significant radiometric variations in at-surface reflectance estimates. Potential solutions to address these limitations included appropriate panel deployment, site-specific sensor calibration, and appropriate BRDF correction. Future UAS based horticultural crop monitoring can benefit from the proposed solutions to radiometric corrections to ensure they are using comparable image-based maps of multi-temporal biophysical properties.

Drug repositioning (also called drug repurposing) is a strategy for identifying new therapeutic targets for existing drugs. This approach is of great importance in pharmacology as it is a faster and cheaper way to develop new medical treatments. In this paper, we present, to our knowledge, the first application of multiplex-heterogeneous network embedding to drug repositioning. Network embedding learns the vector representations of nodes, opening the whole machine learning toolbox for a wide variety of applications including link prediction, node labelling or clustering. So far, the application of network embedding for drug repositioning focused on heterogeneous networks. Our approach for drug repositioning is based on multiplex-heterogeneous network embedding. Such method allows the richness and complexity of multiplex and heterogeneous networks to be projected in the same vector space. In other words, multiplex-heterogeneous networks aggregate different multi-omics data in the same network representation. We validate the approach on a task of link prediction and on a case study for SARS-CoV2 drug repositioning. Experimental results show that our approach is highly robust and effective for finding new drug-target associations.

The properties of the dark matter, dark energy, graviton and photon are discussed in terms of the new three-dimensional quantized space model. Three new particles (bastons) with the electric charges (EC) are proposed as the dark matters. It is proposed that the EC, LC and CC charges are aligned along the time axes but not along the space axes. The photon is confined on its corresponding three-dimensional quantized space. However, the graviton can be evaporated into other three-dimensional quantized spaces. The rest mass of the electron neutrino (n_e) of 3.494·10⁻³ eV/c² is obtained from the experimental vacuum energy density in terms of quantum field theory (QFT). The rest mass and force range of the massive g(0,0,0) graviton with the Planck size are m_g = 3.1872·10⁻³¹ eV/c² and x_r = 3.0955·10²³ m = 10.0 Mpc, respectively, based on the experimental rest mass and rms charge radius of the proton. The possible diameter (10 Mpc) of the largest galaxy cluster is remarkably consistent with the gravitational force range (10 Mpc). Then, the diameter of the largest dark matter distribution related to the largest galaxy cluster is 9.2865·10²³ m = 30 Mpc equal to the force range of the massive g(0) graviton with the rest mass of 1.0624·10⁻³¹ eV/c². Because of the huge number (N) of the evaporated gravitons, the very small Coulomb’s constant of about 10⁻⁴⁸k and large gravitation constant of 10⁶G_N are expected for the charged dark matters. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = 0 for the proton-like particle. The proposed weak gravitational force between the dark matters and normal matters explains the observed dark matter distributions of the bullet cluster, Abell 1689 cluster and Abell 520 cluster. The transition from the galaxy without the dark matters to the galaxy with the dark matters are explained. Also, the accelerated space expansion is caused by the new space quanta created by the evaporated gravitons into the x1x2x3 space and repulsive electromagnetic force between dark matters corresponding to the dark energy. The decreasing coupling constant of the strong force, neutron lifetime anomaly and the pressure distribution inside the proton are explained by the unobservable proton and hadronization. And the rest mass of 1.4 TeV/c² is assigned to the Le particle with the EC charge of −2e. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. Also, the gravitation constant has been changing with the time because of the graviton evaporation.

The airport ground handling service (AGHS) equipment vendor selection (AGHSEVS) problem is critical for ramp work safety management, because AGHS equipment malfunctions affect airport ramp work safety. Appropriate vendor selection can prevent aircraft damage and delays in airlines schedules, and ensure reliable and high-quality ground handling service. The AGHSEVS problem is a time-consuming and complex process that requires professional knowledge and experience to make judgments. Specifically, AGHSEVS is a multi-criteria decision-making (MCDM) problem. Previous research has seldom integrated MCDM methods with linear and goal programming to solve the AGHSEVS problem. The objective of this study was to develop a new system evaluation model for AGHSEVS by considering both qualitative and quantitative methods. We test the proposed approach on an AGHS company in Taiwan.

General Linear Modelling (GLM) has been widely employed to estimate the hemodynamic changes evoked by cognitive processing, which are more likely to be nonlinear than linear. First, this study re-analyzed the fNIRS data (N = 38, Mage = 5.0 years, SD = 0.69 years, 17 girls) collected in the Mixed-Order Design Dimensional Change Card Sort (DCCS) task. The results indicated that the quadratic equation was better than GLM to model HbO changes in this task. Second, analysis of a new set of data indicated that the Habit-DisHabit design of DCCS was more effective in identifying the neural correlates of cognitive shifting than the Mixed-Order Design. Third, this study found that the Non-users were more attentive and engaged than the Heavy-users, with a slower but more steady increase of brain activation in BA8 and BA9.

The option of decarbonizing urban freight transport using Battery Electric Vehicle (BEV) seems promising.However, there is currently a strong debate whether Fuel Cell Electric Vehicle (FCEV) might be the bettersolution. The question arises as to how a fleet of FCEV influences the operating cost, the Greenhouse Gas(GHG) emissions and primary energy demand in comparison to BEVs and to Internal Combustion EngineVehicle (ICEV). To investigate this, we simulate the urban food retailing as a representative share of urbanfreight transport using a multi-agent transport simulation software. Synthetic routes as well as fleet size andcomposition are determined by solving a Vehicle Routing Problem (VRP). We compute the operating costsusing a total cost of ownership (Total Cost of Ownership (TCO)) analysis and the use phase emissions as wellas primary energy demand using the Well To Wheel (WTW) approach. While a change to BEV results in 17 -23% higher costs compared to ICEV, using FCEVs leads to 22 - 57% higher costs. Assuming today’s electricitymix, we show a GHG emission reduction of 25% compared to the ICEV base case when using BEV. Currenthydrogen production leads to a GHG reduction of 33% when using FCEV which however cannot be scaled tolarger fleets. Using current electricity in electrolysis will increase GHG emission by 60% compared to the basecase. Assuming 100% renewable electricity for charging and hydrogen production, the reduction from FCEVsrises to 73% and from BEV to 92%. The primary energy requirement for BEV is in all cases lower and forhigher compared to the base case. We conclude that while FCEV have a slightly higher GHG savings potentialwith current hydrogen, BEV are the favored technology for urban freight transport from an economic andecological point of view, considering the increasing shares of renewable energies in the grid mix.

Existing methods for detecting magnetic leakage signals from damaged wire ropes require axial saturation magnetisation, and the accuracy of the detection equipment depends on the saturation degree of magnetisation. Moreover, the expected magnetisation effect is usually difficult to achieve owing to the special characteristics of the rope structure, diameter, and operating environment of the wire rope. Consequently, in addition to other issues, the detection accuracy and versatility of the equipment are low. In this study, a method based on spatial multidimensional orthogonal array loop magnetisation for detecting mine wire rope defects is proposed. Firstly, a new sensor excitation structure model is developed. Then a method of radiant magnetic flux of permanent magnet array is analysed, and the influence law of the number of permanent radiant magnetic blocks on the magnetisation effect is studied. In addition, a method of wire rope detection based on the principle of clustering is investigated, according to which the influence law of the shape, structure, and size of the polyurethane device on the effect of magnetisation is discussed. Finally, through laboratory experiments, the test model and proposed method are verified. The results show that the magnetisation effect is better and more cost-effective when the number of permanent magnet radiation magnetic block is n=8, and the proposed detection method can effectively distinguish damaged wire rope joints. Furthermore, the proposed equipment achieved signal-to-noise ratio of the signals, improving the reliability of damage detection.

This study presents an instant preview and analysis system implementation of intelligent stereo cameras (ISCs). A parameter optimization prototype adopted the instant preview and analysis system of the ISCs has been achieved the automatic alignment function, and obtained optimal stereo films with the automatic alignment function by adjusting gap and angle between dual cameras. The instant preview and analysis system of the ISCs with parameter optimization can enhance the quality of stereo films effectively and reduce filmed errors and save retouched cost and time in harsh filmed environment.

Measuring farms sustainable innovativeness is a big challenge for both practitioners and academics. The need of sustainable innovativeness assessment in the agricultural business is reasoned in the article. Unfortunately, the features of the farms sustainable innovativeness measurement have not yet been investigated, and any objective methodology for innovativeness assessment is not presented as well. The objective of this article is to find possibility of use some methodology for measuring farm sustainable innovativeness, which would allow ranking farms by this aspect. The article demonstrates the need for multi-criteria method of innovativeness measurement and substantiates the complex proportional assessment method (Copras) as the most appropriate for solution of indicated problem. The model for use of offered method is presented and the practical application of the model is submitted. The final result refuted the opinion that farm innovation depends only on the possibilities to invest funds in a certain area. Indeed, staff creativity and the position of the management regarding certain areas of business make an essential contribution to the sustainable innovativeness level in the agricultural organizations.

Two desirable functions of healthy soil are nutrient cycling and pest suppression. We review recent literature on the contributions of soil microarthropods to soil health through their intersecting roles in decomposition and nutrient cycling and direct and indirect suppression of plant pests. Microarthropods can impact soil and plant health directly by feeding on pest organisms or serving as alternate prey for larger predatory arthropods, and indirectly, by mediating the ability of crop plants to resist or tolerate insect pests and diseases through interactions with the decomposition food web in support of plant nutrition. Soil fauna, including microarthropods, are key regulators of decomposition at local scales but their role at larger scales is unresolved. Future research priorities include the incorporation of multi-channel omnivory into food web modeling and understanding the vulnerability of our soil carbon to increased global temperatures.

The human antibody response to influenza virus infection or vaccination is as complicated as it is essential for protection against flu. The constant antigenic changes of the virus to escape human herd immunity hinder the yearly selection of vaccine strains since it is hard to predict which virus strains will circulate for the coming flu season. A "universal" influenza vaccine that could induce broad cross-influenza subtype protection would help to alleviate this burden. However, the human antibody response is intricate and often obscure, with factors like antigenic seniority or original antigenic sin "OAS", and back-boosting ensuring that each person mounts a unique immune response to infection or vaccination with any new influenza virus strain. Notably, the effects of existing antibodies on cross-protective immunity after repeated vaccinations are unclear. More research is needed to characterize the mechanisms at play, but traditional assays such as hemagglutinin inhibition (HAI) and microneutralization (MN) are excessively limited in scope and too resource-intensive to effectively meet this challenge. In the past ten years, new multiple dimensional assays (MDAs) have been developed to help overcome these problems by simultaneously measuring antibodies against a large panel of influenza hemagglutinin (HA) proteins with a minimal amount of sample in a high throughput way. MDAs will likely be a powerful tool for accelerating the study of the humoral immune response to influenza vaccination and the development of a universal influenza vaccine.

This paper presents the methodology to detect and identify the type of fault that occurs in shunt connected static synchronous compensator (STATCOM) transmission line using a combination of Discrete Wavelet Transform (DWT) and Naive Bayes classifier. To study this, the network model is designed using Mat-lab/Simulink. The different faults such as Line to Ground (LG), Line to Line (LL), Double Line to Ground (LLG) and three-phase (LLLG) fault are applied at different zones of system with and without STATCOM considering the effect of varying fault resistance. The three-phase fault current waveforms obtained are decomposed into several levels using daubechies mother wavelet of db4 to extract the features such as standard deviation and Energy values. The extracted features are used to train the classifiers such as Multi-Layer Perceptron Neural Network (MLP), Bayes and Naive Bayes (NB) classifier to classify the type of fault that occurs in the system. The results reveal that the proposed NB classifier outperforms in terms of accuracy rate, misclassification rate, kappa statistics, mean absolute error (MAE), root mean square error (RMSE), relative absolute error (RAE) and root-relative square error (RRSE) than MLP and Bayes classifier.

This paper presents the design and implementation of a digital control system for modular multilevel converters (MMC) and its use in a 5-kW small scale prototype. To achieve higher system control reliability and multi-functionality, the proposed architecture has been built with an effective split of the control tasks between a master controller and six slave controllers, one for each of the six arms of the converter. The MMC prototype have been used for testing both converter and system level controls in a reduced scale laboratory set up of a Multi-Terminal DC transmission network (MTDC). The whole control has been tested in order to validate the proposed control strategies. The tests performed at system level allowed to explore the advantages of using an MMC in a MTDC system.

Use of a multi-sensor approach can provide citizens a holistic insight in the air quality in their immediate surroundings and assessment of personal exposure to urban stressors. Our work, as part of the ICARUS H2020 project, which included over 600 participants from 7 European cities, discusses data fusion and harmonization on a diverse set of multi-sensor data streams to provide a comprehensive and understandable report for participants, and offers possible solutions and improvements. Harmonizing the data streams identified issues with the used devices and protocols, such as non-uniform timestamps, data gaps, difficult data retrieval from commercial devices, and coarse activity data logging. Our process of data fusion and harmonization allowed us to automate the process of generating visualizations and reports and consequently provide each participant with a detailed individualized report. Results showed that a key solution was to streamline the code and speed up the process, which necessitated certain compromises in visualizing the data. A thought-out process of data fusion and harmonization on a diverse set of multi-sensor data streams considerably improved the quality and quantity of data that a research participant receives. Though automatization accelerated the production of the reports considerably, manual structured double checks are strongly recommended.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

The present study aims to evaluate the capability of the TRMM-3B42-(V7) precipitation product to estimate appropriate precipitation rates in the Upper Indus basin (UIB) and the analysis of the dependency of the estimates’ accuracies on the time scale. To that avail statistical analyses and comparison of the TMPA- products with gauge measurements in the UIB are carried out. The dependency of the TMPA estimates’ quality on the time scale is analysed by comparisons of daily, monthly, seasonal and annual sums for the UIB. The results show considerable biases in the TMPA- (TRMM) precipitation estimates for the UIB, as well as high false alarms and miss ratios. The correlation of the TMPA- estimates with ground-based gauge data increases considerably and almost in a linear fashion with increasing temporal aggregation, i.e. time scale. The BIAS is mostly positive for the summer season, while for the winter season it is predominantly negative, thereby showing a slight over-estimation of the precipitation in summer and under-estimation in winter. The results of the study suggest that, in spite of these discrepancies between TMPA- estimates and gauge data, the use of the former in hydrological watershed modelling, endeavoured presently by the authors, may be a valuable alternative in data- scarce regions, like the UIB, but still must be taken with a grain of salt.

Remote sensing technology provides a new way to explore the earth for geoscience applications. In the context of continuous deepening of geological research and the vigorous development of geospatial information science, 3D geological modeling technology has become a research hotspot in the intersection of earth science and information science. The traditional 3D geological modeling technology refers to underground 3D modeling using geological data. This modeling method can only display the underground scene in 3D visualization, but cannot display the surface in detail. In this study, remote sensing technology is adopted to improve the traditional 3D geological modeling method, so that geological modeling can be integrated with remote sensing image, and a new 3D geological modeling method based on remote sensing technology is developed. This method can perform integrated 3D visualization of underground and aboveground scenes, which provides a new way for disaster prevention and reduction, geological prospecting and tectonic interpretation. The new 3D geological modeling method is mainly applied in the geological field, and has made new progress in multi-source heterogeneous geological data fusion, large-scale high-precision modeling, geological grid subdivision, attribute modeling technology, remote sensing image fusion and other aspects. Taking the Ya'an area as an example, this paper makes use of the new generation of 3D geological modeling technology to carry out 3D geological modeling and visual display. The 3D visualization in Ya'an area verifies the feasibility and effectiveness of the new 3D geological modeling method based on remote sensing technology in the current data environment.

Electric moped scooter sharing services have recently experienced strong growth rates, particularly in Europe. Due to their compactness, environmental-friendliness and convenience, shared e-mopeds are suitable modes of transport in urban mobility to help reduce the environmental impact. However, its traffic-related, economic and environmental effects are merely represented in academic research. We used passenger car traffic data in Berlin generated by the multi-agent transport simulation framework MATSim to develop a python-based simulation, resembling an e-moped sharing system. Based on the results, a total cost of ownership and a life cycle assessment for fleet sizes of 2,500, 10,000 and 50,000 vehicles were conducted. The results indicate that a substantial part of all passenger car trips in Berlin can be substituted. The larger the fleet, the more and longer trips are replaced. Simultaneously, the efficiency in terms of fleet utilization decreases. The scenario with 10,000 e-mopeds offers the lowest total distance-based costs for sharing operators, whereas a fleet consisting of 2,500 vehicles exhibits the lowest environmental emissions per kilometer driven over the expected lifespan of a shared e-moped. Based on the renewable energy potential for 2050 forecasted by the German Federal Environment Agency, a significant overall decline in environmental impacts can be achieved.

Tree condition, pruning and orchard management practices within intensive horticultural tree crop systems can be determined via measurements of tree structure. Multi-spectral imagery acquired from an unmanned aerial system (UAS) has been demonstrated as an accurate and efficient platform for measuring various tree structural attributes, but research in complex horticultural environments has been limited. This research established a methodology for accurately estimating tree crown height, extent, plant projective cover (PPC) and condition of avocado tree crops, from a UAS platform. Individual tree crowns were delineated using object-based image analysis. In comparison to field measured canopy heights, an image-derived canopy height model provided a coefficient of determination (R2) of 0.65 and relative root mean squared error of 6%. Tree crown length perpendicular to the hedgerow was accurately mapped. PPC was measured using spectral and textural image information and produced an R2 value of 0.62 against field data. A random forest classifier was applied to assign tree condition into four categories in accordance with industry standards, producing out-of-bag accuracies >96%. Our results demonstrate the potential of UAS-based mapping for the provision of information to support the horticulture industry and facilitate orchard-based assessment and management.

In the process of sustainable development in the future, human society faces problems such as severe population load, economic transition, and lack of educational measures. One of the root causes of these problems is the shortage of innovative talents. Therefore, how to cultivate learners with multi-disciplinary integration and innovation ability is the key point that should be paid attention to in promoting the concept of quality education and coping with the future sustainable development process. This paper uses questionnaire survey method and literature analysis method to analyze the development of many educational institutions with STEAM concept as the core in China since 2017. It is found that the existing STEAM educational institutions generally have the following problems: the lack of team composition、difficulty in independent research and development、single course content and insufficient validation of course effectiveness. In order to more effectively promote the sustainable development of China's future course, STEAM education institutions should focus on strengthening the following development strategy: gradient team building, continuous independent research and development, cutting-edge projects curriculum transformation mechanism and multi-angle course effectiveness verification.

Tumor growth, progression, and therapy resistance are crucial factors in the prognosis of cancer. Properties of three-dimensional tumor-like organoids (tumoroids) more closely resemble in vivo tumors compared to two-dimensionally cultured cells and are therefore effectively used for assays and drug screening. We here established a repurposed drug for novel anticancer research and therapeutics using a tumoroid-based screening system. We screened 6 pharmacologically active compounds by using an original tumoroid-based multiplex phenotypic screening system with matrix metalloproteinase 9 (MMP9) promoter-driven fluorescence reporter for the evaluation of both tumoroid formation and progression. The effects of one of the hit compounds were examined on tumor formation and progression in vitro and in vivo. Antiparkinson drug benztropine was the most effective compound uncovered by the screen. Benztropine significantly inhibited in vitro tumoroid formation, cancer cell survival, and MMP9 promoter activity. Benztropine also reduced the activity of oncogenic signaling transducers and trans-activators for MMP9, including STAT3, NF-κB, and β-catenin, and properties of cancer stem cells / cancer-initiating cells. Benztropine and GBR-12935 directly targeted the dopamine transporter DAT/SLC6A3, whose genetic alterations such as amplification were correlated with poor prognosis for cancer patients. Benztropine also inhibited tumor growth, circulating tumor cell (CTC) number, and rate of metastasis in a tumor allograft model in mice. In conclusion, we propose the repurposing of benztropine for anticancer research and therapeutics that can suppress tumor progression, CTC, and metastasis of aggressive cancers by reducing key pro-tumorigenic factors.

This article deals with the conformable double Laplace transforms and their some properties with examples and also the existence Condition for the conformable double Laplace transform is studied. Finally, in order to obtain the solution of nonlinear fractional problems, we present a modified conformable double Laplace that we call conformable double Laplace decomposition methods (CDLDM). Then, we apply it to solve, Regular and singular conformable fractional coupled burgers equation illustrate the effectiveness of our method some examples are given.

Timely diagnosis of Alzheimer's diseases(AD) is crucial to obtain more practical treatments. In this paper, a novel approach Based on Multi-Level Fuzzy Neural Networks (MLFNN) for early detection of AD is proposed. The focus of study was on the problem of diagnosing AD and MCI patients from healthy people using MLFNN and selecting the best feature(s) and most compatible classification algorithm. In this way, we achieve an excellent performance using only a single feature i.e. MMSE score, by fitting the optimum algorithm to the best area using optimum possible feature(s) namely one feature for a real life problem. It can be said, the proposed method is a discovery that help patients and healthy people get rid of painful and time consuming experiments. Experiments shows the effectiveness of proposed method in current research for diagnosis of AD with one of the highest performance (accuracy rates of 96.6%), ever reported in the literature.

Deep learning has been applied in many areas that have had a significant impact on applications that improves real-life challenges. The success of deep learning in a wide range of areas is due in part to the use of activation functions, which are particularly effective at solving non-linear problems. Activation functions are a key focus for researchers in artificial intelligence who aim to improve the performance of neural networks. This article provides a comprehensive explanation and comparison of different activation functions, with a focus on the arc tangent and its variations specifically. The paper presents experimental results that show that variations of the arc tangent using irrational numbers such as pi, the golden ratio, and Euler’s number, as well as a self-arctan function, produce promising results. Since we experimented with promising activation functions on two different problems, and datasets, we reached a result that different irrationals work well for different problems. In other words, arctan ϕ gives the best results mostly for multiclass classification and arctan e gives the best results for time series prediction problems. The paper focuses on a multi-class classification problem applied to the Reuters Newswire dataset and a time-series prediction problem on Türkiye energy trade value to show the impacts of activation functions.

The paper briefly reviews the Clifford algebras of space Cl(3,0) and anti-space Cl(0,3) with a particular focus on the paravector representation, emphasizing the fact that both algebras have an isomorphic center represented just by two coordinates. Since the paravector representation allows assigning the scalar element of grade 0 to the time coordinate, we consider the relativity in such two-dimensional spacetime for a uniformly accelerated frame with the constant acceleration 3Hc. Using the Rindler coordinate transformations in two-dimensional spacetime and then applying it to Minkowski coordinates, we obtain the FLRW metric, which in the case of the Clifford algebra of space Cl(3,0) corresponds to the anti-de Sitter (AdS) flat (k=0) case, the negative cosmological term and an oscillating model of the universe. The approach with anti-Euclidean Clifford algebra Cl(0,3) leads to the de Sitter model with the positive cosmological term and the exact form of the scale factor used in modern cosmology.

Although different assessments and evaluations of Dual-Miller cycle performed, specified output power and thermal performance associated with engine determined. Besides, multi objective optimization of thermal efficiency, Ecological Coefficient of performance ( ) and Ecological function ( ) by the mean of NSGA-II technique and thermodynamic analysis performed. The Pareto optimal frontier obtaining the best optimum solution is chosen by fuzzy Bellman-Zadeh, LINMAP, and TOPSIS decision-making techniques. Based on the results, performances of dual-Miller cycles and their optimization are improved.

This study presents application of demand response strategy in a standalone wind-solar-battery hybrid energy system (HES). Inputs for the designed HES are wind speed, solar radiation, temperature and load demand which is variable with time. In this study, hourly values of meteorological data and hourly load demand are considered in one year. An improved gravitational search algorithm (IGSA) is used to optimize the configuration of the standalone wind-solar-battery hybrid power system. The optimal objectives of the system are cost of the system in life cycle, the loss of power supply probability（LPSP）and the energy excess percentage（EXC）.The effect of demand response on economic benefit and energy storage allocation of the standalone wind-solar-battery system is studied. The obtained optimal configuration of the proposed HES can provide minimal energy cost with excellent performance and reduced waste and unmet load.

From ancient time, electric grid system developed as one way direction in which users get the electricity from generators to far end. However, it is not the consumer centric as its one way process and consumer have no way to communicate to the server. Thus, with the development of digital revolution, the grid converted to smart grid and meter converted to smart meter. In smart grid, the protocol follows the bidirectional way of communication with support of consumers in the system. Recently in 2016, Jo et al. proposed the scheme for smart grid system using privacy preserving model and claimed to be efficient and secure. However, in this paper we have analyzed the scheme of Jo et al. and proved that the scheme is vulnerable to Replay attack and afterwards shows the change in protocol to withstand against this attack.

Background: Upper extremities’ function impairments (UEFI) and gait impairment are frequently reported even in the early stages of Multiple Sclerosis (MS) disease. These motor deficits can negatively affect the quality of life (QOL) in MS patient. Exercise has been repeatedly introduced as a beneficial adjuvant therapy for MS, attenuating a wide range of physical and psychological symptoms without any side effects or increased risks of relapse or exacerbation in disease symptoms.Aim: This paper investigates the effect of multi-function swing suspension training (MFSST) program on upper and lower extremities’ function (ULEF), and QOL in MS women according to expanded disability status scale (EDSS) score.Design: Experimental method with a pre-test and post-test design with control group. Setting: The department of Sports Injuries and Corrective Exercise at the Shahid Bahonar University of Kerman.Population: Forty-seven MS women.Methods: Eligible subjects who matched the selection criteria were randomly assigned into three groups as follow: i. Intervention group A (EDSS of 2 – 4), ii. Intervention group B (EDSS of 4.5 – 6.5), and iii. Control group (EDSS of 2 – 6.5). The intervention groups have been trained by the SET program for a duration of 8 weeks. At baseline and after the intervention, the upper extremities’ function (UEF) and the lower extremities’ function (LEF) were assessed by 9-hole peg test (9HPT) and the timed 25-foot walk (T25FW) test, respectively. Moreover, participants’ QOL was measured using the Short Form questionnaire (SF-36).Results: A significant difference was found between the pre-test and post-test variables of walking speed and upper extremity endurance in intervention groups, and between the intervention groups and control group (P < 0.05). Compared to control group, both intervention groups showed improvements in all subscales of QOL, except emotional role limitation score.Conclusions: In summary, these results show that the present protocol of MFSST could be effective in improving ULEF and QOL in MS patients, showing the improvements after 4^th week. Moreover, this protocol was more useful for patients with an EDSS score of more than 4.5. Therefore, it seems that exercise therapy should be considered as a beneficial clinical intervention approach to improve ULEF and QOL in MS patients.

The paper considers new effects of the nanoscale state of matter, which open up prospects for the creation of electronic devices using new physical principles. The contact of chemically homogeneous different sizes hydrated nanoparticles of yttrium-stabilized zirconium oxide (ZrO2 – x %mol Y2O3, x=0, 3, 4, 8; YSZ) with particle sizes of 7.5 nm and 7,5 nm; 7.5 nm and 9 nm; 7.5 nm and 11 nm; 7.5 nm and 14 nm in the form of compacts obtained using high hydrostatic pressure (HP-compacts of 300MPa) was studied at direct and alternating current. A unique size effect of the nonlinear (semiconductor) dependence of the electrical properties (in the region U <2.5 V, I ≤ 2.7 mA) of the contact of different-sized YSZ nanoparticles of the same chemical composition is revealed, which indicates the possibility of creating semiconductor structures of a new type based on chemically homogeneous nanostructured systems. The electronic structure of the near-surface regions of nanoparticles of a special type of oxide materials and the possibility, on this basis, to obtain specifically rectifying properties of the contacts were studied theoretically. Models of surface states of the Tamm type are constructed, but considering the Coulomb long-range action. The discovered variance and its dependence on the curvature of the surface of nanoparticles made it possible to study the conditions for the formation of a contact potential difference in cases of nanoparticles of the same radius (synergistic effect), different radii (doped and undoped variants), as well as to discover the possibility of describing a group of powder particles from material within the Anderson model. The established effect makes it possible to solve the problem of diffusion instability of semiconductor heterojunctions and opens up prospects for creating electronics devices with a fundamentally new level of properties for use in various fields of the national economy and breakthrough critical technologies.

Volcanism powered by tidal forces inside celestial bodies can provide enough energy to keep important solvents for living systems in the liquid phase. Moreover, tidal forces and their environmental consequences may strongly influence habitability of planets and other celestial bodies and may result in special forms of live and living conditions. A prerequisite to calculate such tidal interactions and consequences is depending on simulations for tidal accelerations in a multi-body system. Unfortunately, from measurements in many extrasolar planetary systems only few physical and orbital parameters are well enough known for investigated celestial bodies. For calculating tidal acceleration vectors under missing most orbital parameter exactly, a simulation method is developed that is only based on a few basic parameters, easily measurable even in extrasolar planetary systems. Such a method as being presented here, allows finding a relation between the tidal acceleration vectors and potential heating inside celestial objects. Using values and results of our model approach to our solar system as a “gold standard” for feasibility allowed us to classify this heating in relation to different forms of volcanism. This “gold standard” approach gave us a classification measure for the relevance of tidal heating in other extrasolar systems with a reduced availability of exact physical parameters. We would help to estimate conditions for the identification of potential candidates for further sophisticated investigations by more complex established methods like viscoelastic multi-body theories. As a first example, we applied the procedures developed here to the extrasolar planetary system TRAPPIST-1 as an example to check our working hypothesis.

This investigation explores a novel path-planning and optimization strategy for multiple cooperative robotic agents, applied in a fully observable and dynamically changing obstacle field. Current dynamic path planning strategies employ static algorithms operating over incremental time-steps. We propose a cooperative multi-agent (CMA) based algorithm, based on natural flocking of animals, using vector operations. It is preferred over more common graph search algorithms like A* as it can be easily applied for dynamic environments. CMA algorithm executes obstacle avoidance using static potential fields around obstacles, that scale based on relative motion. Optimization strategies including interpolation and Bezier curves are applied to the algorithm. To validate effectiveness, CMA algorithm is compared with A* using static obstacles due to lack of equivalent algorithms for dynamic environments. CMA performed comparably to A* with difference ranging from -0.2% to 1.3%. CMA algorithm is applied experimentally to achieve comparable performance, with an error range of -0.5% to 5.2%. These errors are attributed to the limitations of the Kinect V1 sensor used for obstacle detection. The algorithm was finally implemented in a 3D simulated space, indicating that it is possible to apply with drones. This algorithm shows promise for application in warehouse and inventory automation, especially when the workspace is observable.

Additive manufacturing (AM) is an emerged layer-by-layer manufacturing process. However, its broad adoption is still hindered by limited material options, different fabrication defects, and inconsistent part quality. Material extrusion (ME) is one of the most widely used AM technologies, and, hence, is adopted in this research. Low-cost metal ME is a new and AM technology used to fabricate metal composite parts using sintered metal infused filament material. Since the involved materials and process are relatively new, there is a need to investigate the dimensional accuracy of ME fabricated metal parts for real-world applications. Each step of the manufacturing process, from the material extrusion to sintering, might significantly affect the dimensional accuracy. This research provides a comprehensive analysis of dimensional changes of metal samples fabricated by the ME and sintering process, using statistical and machine learning algorithms. Machine learning (ML) methods can be used to assist researchers in sophisticated pre-manufacturing planning and product quality assessment and control. This study compares linear regression to neural networks in assessing and predicting the dimensional changes of ME made components after 3D printing and sintering process. The prediction outcomes using a neural network performed the best with the highest accuracy as compared to regression. The findings of this study can help researchers and engineers to predict the dimensional variations and optimize the printing and sintering process parameters to obtain high quality metal parts fabricated by the low-cost ME process.

In this paper we describe and exploit a geometric framework for Gibbs probability densities and the associated concepts in statistical mechanics, which unifies several earlier works on the subject, including Souriau's symplectic model of statistical mechanics, its polysymplectic extension, Koszul model, and approaches developed in quantum information geometry. We emphasize the role of equivariance with respect to Lie group actions and the role of several concepts from geometric mechanics, such as momentum maps, Casimir functions, coadjoint orbits, and Lie-Poisson brackets with cocycles, as unifying structures appearing in various applications of this framework to information geometry and machine learning. For instance, we discuss the expression of the Fisher metric in presence of equivariance and we exploit the property of the entropy of the Souriau model as a Casimir function to apply a geometric model for energy preserving entropy production. We illustrate this framework with several examples including multivariate Gaussian probability densities, and the Bogoliubov-Kubo-Mori metric as a quantum version of the Fisher metric for quantum information on coadjoint orbits. We exploit this geometric setting and Lie group equivariance to present symplectic and multisymplectic variational Lie group integration schemes for some of the equations associated to Souriau symplectic and polysymplectic models, such as the Lie-Poisson equation with cocycle.

Salinity acts as a critical environmental filter on microbial communities in natural systems, negatively affecting microbial diversity. However, how salinity affects the community assembly remains unclear. This study used Wendeng multi-pond saltern as a model to evaluate the prokaryotic community composition and diversity and quantify the relative importance of ecological processes across salinity gradients. Results showed that low saline salterns (45-80 g/L) exhibited higher bacterial diversity than those in high saline salterns (175-265 g/L). The relative abundance of taxa assigned to Halanaerobiaceae, Haloferacaceae, Desulfohalobiaceae, Phormidiaceae, Rohodobacteraceae, and Nitrococcaceae was higher with increasing salinity. Salinity and pH were the primary environmental factors that directly or indirectly determined the composition and diversity of prokaryotic communities. Microbial co-occurrence network dynamics were more complex in the sediment than in water of salterns. An infer Community Assembly Mechanisms by Phylogenetic-bin-based null model analysis (iCAMP) showed that microbial community assembly in sediment and water differed. Our findings provide more information about microbial community structure and the importance of various ecological processes in controlling microbial community diversity and succession along salinity gradients in water and sediment environments.

ARBTools is a Python library containing a Lekien-Marsden type tricubic spline method for interpolating three-dimensional scalar or vector fields presented as a set of discrete data points on a regular cuboid grid. ARBTools was developed for simulations of magnetic molecular traps, in which the magnitude, gradient and vector components of a magnetic field are required. Numerical integrators for solving particle trajectories are included, but the core interpolator can be used for any scalar or vector field. The only additional system requirements are NumPy.

This paper details the evolution of access network sharing models from legacy DSL to the most recent fibre-based technology and the main challenges faced from a technical and business perspectives. We first give an overview of existing access sharing models, that span physical local loop unbundling and virtual unbundled local access. We then describe different types of optical access technologies and highlight how they support network sharing. Next, we examine how the concept of SDN and network virtualization has been pivotal in enabling the idea of “true multi-tenancy”, through the use of programmability, flexible architecture and resource isolation. We give examples of recent developments of cloud central office and OLT virtualization. Finally, we provide an insight into the role that novel business models, such as blockchain and smart contract technology, could play in 5G networks. We discuss how these might evolve, to provide flexibility and dynamic operations that are needed in the data and control planes.

Hydraulic conductivity is the key and one of the most uncertain parameters in groundwater modeling. The grid based numerical simulation require spatial distribution of sampled hydraulic conductivity at un-sampled locations in the study area. This spatial interpolation has been routinely performed using variogram based models (two-point geostatistics methods). These traditional techniques fail to capture the complex geological structures, provides smoothing effects and ignore the higher order moments of subsurface heterogeneities. In this work, a multiple-point geostatistics (MPS) method is applied to interpolate hydraulic conductivity data which will be further used in WASH123D numerical groundwater simulation model for regional smart groundwater management. To do this, MPS need ‘training images (TIs) as a key input. TI is a conceptual model of subsurface geological heterogeneity which was developed by using concept of ages, topographic slope as an index criteria and knowledge of geologist. After considerations of full physics of study area, an example shows the advantages of using multiple-point geostatistics compared with the traditional two-point geostatistics methods (such as Kriging) for the interpolation of hydraulic conductivity data in a complex geological formation.

Clustered regularly interspaced short palindromic repeats/associated protein 9 nuclease (CRISPR/Cas9) technology guided by a single-guide RNA (sgRNA) has recently opened a new avenue for antiviral therapy. A unique capability of the CRISPR/Cas9 system is multiple genome engineering. However, there are few applications in insect viruses by a single Cas9 enzyme targeting two or more sgRNA at different genomic sites for simultaneous production of multiple DNA breaks. To address the need for multi-gene editing and sustained delivery of multiplex CRISPR/Cas9-based genome engineering tools, we developed a one-vector (pSL1180-Cas9-U6-sgRNA) system to express multiple sgRNA and Cas9 protein to excise Bombyx mori nucleopolyhedrovirus (BmNPV) in insect cells. Here, ie-1, gp64, lef-11, and dnapol genes were screened and identified as multiple sgRNA editing sites according to the BmNPV system infection and DNA replication mechanism. Furthermore, we constructed a multiplex editing vector sgMultiple to efficiently regulate multiplex gene editing steps and inhibit BmNPV replication after viral infection. This is the first report that describes the application of multiplex CRISPR/Cas9 system inhibiting insect virus replication. This multiplex system can significant enable the potential of CRISPR/Cas9-based multiplex genome engineering in transgenic silkworms.

There exist numerous high-dimensional problems in the real world which cannot be solved through the common traditional methods. The metaheuristic algorithms have been developed as successful techniques for solving a variety of complex and difficult optimization problems. Notwithstanding their advantages, these algorithms may turn out to have weak points such as lower population diversity and lower convergence rate when facing complex high-dimensional problems. An appropriate approach to solve such problems is to apply multi-agent systems along with the metaheuristic algorithms. The present paper proposes a new approach based on the multi-agent systems and the concept of agent, which is named Multi-Agent Metaheuristic (MAMH) method. In the proposed approach, several basic and powerful metaheuristic algorithms, including Genetic Algorithm (GA), Particle Swarm Optimization (PSO), Artificial Bee Colony (ABC), Firefly Algorithm (FA), Bat Algorithm (BA), Flower Pollination Algorithm (FPA), Gray Wolf Optimizer (GWO), Whale Optimization Algorithm (WOA), Crow Search Algorithm (CSA), Farmland Fertility Algorithm (FFA), are considered as separate agents each of which sought to achieve its own goals while competing and cooperating with others to achieve the common goals. In overall, the proposed method was tested on 32 complex benchmark functions, the results of which indicated effectiveness and powerfulness of the proposed method for solving the high-dimensional optimization problems. In addition, in this paper, the binary version of the proposed approach, called Binary MAMH (BMAMH), was executed on the spam email dataset. According to the results, the proposed method exhibited a higher precision in detection of the spam emails compared to other metaheuristic algorithms and methods.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

Like traditional single label learning, multi-label learning is also faced with the problem of dimensional disaster.Feature selection is an effective technique for dimensionality reduction and learning efficiency improvement of high-dimensional data. In this paper, Logistic regression, manifold learning and sparse regularization were combined to construct a joint framework for multi-label feature selection (LMFS). Firstly, the sparsity of the eigenweight matrix is constrained by the $L_{2,1}$-norm. Secondly, the feature manifold and label manifold can constrain the feature weight matrix to make it fit the data information and label information better. An iterative updating algorithm is designed and the convergence of the algorithm is proved.Finally, the LMFS algorithm is compared with DRMFS, SCLS and other algorithms on eight classical multi-label data sets. The experimental results show the effectiveness of LMFS algorithm.

The Vehicle Routing Problem (VRP) and its variants are found in many fields, especially logistics. In this study, we introduced an adaptive method to a complex VRP. It combines multi-objective optimization and several forms of VRPs with practical requirements for an urban shipment system. The optimizer needs to consider terrain and traffic conditions. The proposed model also considers customers' expectations, shipper considerations as goals, and the common goal like transportation cost. We offered compromise programming to approach the multi-objective problem by decomposing the original multi-objective problem into a minimized distance-based problem. We designed a hybrid version of the Genetic algorithm with the Local Search algorithm to solve the proposed problem. We evaluate the effectiveness of the proposed algorithm with the Tabu Search algorithm, the original Genetic algorithm on the tested dataset. The results show that our method is an effective decision-making tool for the multi-objective VRP and an effective solver for the new variation of VRP.

In this work, we show that a late fusion approach to multi-modality in sign language recognition improves the overall ability of the model in comparison to the singular approaches of Computer Vision (88.14%) and Leap Motion data classification (72.73%). With a large synchronous dataset of 18 BSL gestures collected from multiple subjects, two deep neural networks are benchmarked and compared to derive a best topology for each. The Vision model is implemented by a CNN and optimised MLP and the Leap Motion model is implemented by an evolutionary optimised deep MLP topology search. Next, the two best networks are fused for synchronised processing which results in a better overall result (94.44%) since complementary features are learnt in addition to the original task. The hypothesis is further supported by application of the three models to a set of completely unseen data where a multi-modality approach achieves the best results relative to the single sensor method. When transfer learning with the weights trained via BSL, all three models outperform standard random weight distribution when classifying ASL, and the best model overall for ASL classification was the transfer learning multi-modality approach which scored 82.55% accuracy.