Recent climate change and water pollution has affected algal diversity resulting in emergence of more tolerant species. They can be the indicators of water quality, pollution and seasonal changes. Present study revealed the green algal diversity and distribution pattern according to water parameters and season in the Lucknow City, India. The water sample were collected from seven sites within Lucknow and outskirts. The occurrence of a total of 36 taxa of green algae belonging to 11 genera are recorded. It has been observed that less polluted water is dominated by Spirogyra; where conductivity, TDS and salinity of water were low. Whereas the more polluted water was dominated by desmids. Dominance index was found highest in site 4 (0.61), where only three taxa were identified; whereas the lowest (0.13) was measured in site 1, where nine taxa were identified. This study also recorded several algal taxa for the first time from Lucknow.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

Two series of novel [1,2,4]triazolo[4,3-c]- and [1,2,4]triazolo[1,5-c]quinazoline fluorophores with 4’-amino[1,1′]-biphenyl residue at position 5 have been prepared via Pd-catalyzed cross-coupling Suzuki-Miyaura reactions. The treatment of 2-(4-bromophenyl)-4-hydrazinoquinazoline with orthoesters in solvent-free conditions or in absolute ethanol leads to the formation of [4,3-c]-annulated triazoloquinazolines, whereas [1,5-c] isomers are formed in acidic media as a result of Dimroth rearrangement. 1D-NMR and 2D-NMR spectroscopy as well as single‐crystal X‐ray diffraction analysis unambiguously confirmed the annelation type and determined the molecular structure of p-bromophenyl intermediates and target products. Photophysical properties of the target compounds were investigated in two solvents and solid state and compared with those of related 3-aryl-substituted [1,2,4]triazolo[4,3-c]quinazolines. The excluding of aryl fragment from triazole ring has been revealed to improve fluorescence quantum yield in solution. Most of the synthesized structures show moderate to high quantum yields in solution. Additionally, the effect of solvent polarity on the absorption and emission spectra of fluorophores has been studied and considerable fluorosolvatochromism was stated. Moreover, electrochemical investigation and DFT calculations have been performed, their results are consistent with the experimental observation.

Radical reactions are powerful in the synthesis of diverse molecular scaffolds bearing functional groups. In pervious review articles, we have presented 1,2-difunctionalizations, remote 1,3-, 1,4-, 1,5-, 1,6- and 1,7-difunctionalizations, and addition followed by cyclization reactions. Presents in this paper are radical cyclization followed by the second functionalization reactions. The second functionalization could be realized by atom transfer reactions, radical or transition metal-assisted coupling reactions, and reactions with neutral molecules, cationic and anionic species.

Recent experiments devoted to characterizing the behavior of sessile ferroelectric liquid droplets on ferroelectric solid substrates, showed the existence of a droplet electromechanical Rayleigh-like instability. The instability is induced by the bulk polarization of the ferroelectric fluid which couples to the polarization of the underlying substrate through its fringing field and solid-fluid interface coupling. With the aim of characterizing this phenomenon, namely the coupling between the polarizations of a fluid and a solid material, we studied the behavior of ferroelectric liquid droplets confined between two solid substrates, arranged in different configurations realized so to generate fringing fields with different profiles. Results show that the features of the droplets instability are indeed affected by the specific fringing field shape in a way dominated by the minimization of the electrostatic energy associated to the bulk polarization of the ferroelectric fluid.

Achieving the dual development of rural revitalization and urbanization is an important strategic goal of China’s current modernization. Rural population and settlements are the main components of the countryside in traditional agricultural areas, and play an important role in the development of the countryside itself in terms of urban and rural land use and in the formation of urban and rural development patterns. This study analyzes the spatial and temporal changes in rural populations and settlements at the township level, as well as the degree and type of coupled development. A framework for urban–rural development relationships based on different types of coupled development is proposed, and a model of urban–rural forces is constructed to derive the spatial pattern of urban–rural development at the township level that may be formed in the future. Our study shows that the rural population and settlements in the study area are characterized by significant spatial and temporal dynamics, indicating that traditional rural areas are in a process of rapid development and change. The results of the township-level coupling measurements present four types of development in terms of the spatial pattern of urban–rural development: A-type is most likely to produce new cities or satellite towns in the Jixi–Harbin–Qiqihar area in the future; B-type is the fastest dying area in the future, located in the Harbin and Qitaihe clusters, with a tendency to merge into Harbin; C-type is the area to be focused on in the future to attract population and strictly control the growth of the rural settlement area to avoid it turning into B-type; D-type may develop regional township centers in the future in the combined area of Jiamusi City, Suihua City and Mudanjiang City. The results of the study provide experience in realizing rural revitalization according to local conditions. The new spatial pattern of urban–rural development provides an important reference for formulating land use policies, optimizing urban–rural land allocation and realizing integrated urban–rural development strategies.

Introduction: Systemic lupus erythematosus (SLE) is an autoimmune disease associated with an increased risk of cardiovascular diseases (CVD), leading to elevated mortality rates among patients. We aimed to evaluate the levels of cardio-ankle vascular index (CAVI), global longitudinal strain (GLS), ventricular-arterial coupling (VAC) and high-sensitivity cardiac troponin (hsTn), in SLE patients and to explore their relationship with clinical parameters. Methods: This cross-sectional study enrolled 82 SLE patients without evident cardiac or kidney impairment and 41 age- and sex matched healthy controls. We comparatively evaluated CAVI, GLS, VAC, and hsTn between SLE patients and controls, and we assessed their association among SLE patients with disease activity based on the SELENA-SLEDAI Activity Index. Multivariate regression analysis was performed to identify independent predictors of CAVI and hsTn within the SLE cohort. Results: In comparison to healthy controls, SLE patients presented with significantly higher CAVI, GLS and hsTn levels, while VAC was significantly reduced (p<0.001). Further, SLE patients with active disease (SELENA-SLEDAI≥4) exhibited higher levels of CAVI and troponin than those with inactive disease (p<0.001). SLEDAI was an independent predictor of CAVI, while VAC and SLEDAI were independent determinants of hsTn in SLE cohort. Conclusion: SLE patients displayed abnormal levels of CAVI, VAC, GLS, and troponin compared to healthy individuals. Our findings implicate the potential of those CV novel CVD risk factors to refine screening and therapeutic strategies for this specific population.

The methods of Artificial Intelligence (AI) have been used in the planning and operation of power systems for more than 40 years. In recent years, due to the development of microprocessor and data storage technologies, the effectiveness of this use has greatly increased. This paper provides a systematic overview of the application of AI including the use of Machine Learning (ML) to the power system. The potential application areas are divided into four blocks and the classification matrix has been used for clustering the AI application tasks. Furthermore, the data acquisition methods for setting the parameters of AI and ML algorithms are presented and discussed in a systematic way considering the supervised and unsupervised learning methods. Based on this, three complex application examples: wind power generation forecasting, smart grid security as-sessment (using two methods), and automatic system fault detection are presented and discussed in detail. Summary and outlook conclude the paper.

Relative to several model bacteria, the ethanologenic bacterium Zymomonas mobilis is shown here to have an elevated resistance to exogenous antimicrobial peptides (AMPs) – both, with regard to peptide bulk concentration in the medium, and the numbers of peptide molecules per cell. By monitoring integration of the AMPs in the bacterial cell membrane and observing the resulting effect on membrane energy-coupling, it is concluded that the membranotropic effects of the tested AMPs in Z. mobilis and in Escherichia coli are comparable. The advantage of Z. mobilis over E. coli apparently results from its uncoupled mode of energy metabolism that, in contrast to E. coli, does not rely on oxidative phosphorylation, and hence, is less vulnerable to disruption of its energy-coupling membrane by AMPs. It is concluded that the high resistance to antimicrobial peptides (AMPs) observed in Z. mobilis not only proves crucial for its survival in its natural environment but also offers a promising platform for AMP production and sheds light on potential strategies for novel resistance development in clinical settings.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

This paper examines the response of the ionosphere to the impact of two moderate geomagnetic storms observed in January 17 and 26-27, 2013 under conditions of strong sudden stratospheric warming. The study uses data from ground-based ionosonde measurements at the Alma-Ata ionospheric station (43.25 N, 76.92 E) combined with optical observation data (The Spectral Airglow Temperature Imager (SATI)). Ionosonde data showed that the geomagnetic storms under consideration do not generate ionospheric storms, but demonstrate some unusual types of diurnal foF2 variations with large (up to 60%) deviations of foF2 from median values observed during the night/morning periods on 13-15 and 20-23 January which do not have any relation to solar or geomagnetic activity. Wave-like disturbances in foF2, h’F and daily averaged foF2 values with quasi-period of 5-8 days and peak-to-peak amplitude from about 1MHz to 2 MHz (from 20% to 40%) and ~40 km are observed during the 9-28 January, after registration the occurrence of the major SSW event on 6-7 January. The observed variations in the OH emission rate are found to be quite similar to those observed in the ionosheric parameters that assume a community of processes in the stratosphere/mesosphere/ionosphere system. The study shows that the F-region of the ionosphere is influenced by processes in the lower ionosphere, in this case by processes associated with sudden stratospheric warming SSW-2013, which led to modification of the structure of the ionosphere and compensation of processes associated with the development of the ionospheric storms.

A difficult open problem that has never been fully resolved in the literature to date is the behaviour of the (TDCDP) third approximation. As a giant step towards modern control theory, this cutting-edge paper will advance control theory and other relevant inter-disciplinary subjects. Because control theory is important in industry and engineering, this study will be especially beneficial to anyone working in these disciplines who wish to understand more about recent advances in control theory settings. In contrast, the wealth of applications of Fokker Planck Kolmogorov (FPK) equations numerous disciplines As a result, the study instantly gains more taste and credibility. At the end of the paper, there are several challenging open problems, some concluding remarks, and recommendations for further investigation.

This paper investigates a numerical code coupling technique to tackle multi-physics and multi-scale simulations using state-of-the-art software packages that typically address some specific modeling domain. The coupling considers the in-house FEM code, FEMuS, and the FVM code OpenFOAM, by exploiting the MED library from the SALOME platform. The present approach is tested on a buoyancy-driven fluid flow within a square cavity, where the buoyancy force constitutes the coupling term. In uncoupled scenarios, momentum and temperature equations are solved both in FEM and FVM codes without data exchange. In the coupled setting, only the OpenFOAM velocity and the FEMuS temperature fields are solved separately and shared at each time step (or vice versa). The MED library handles the coupling with the addition of suitable ad-hoc data structures that perform the field transfer between codes. Different Rayleigh numbers are investigated, comparing the outcomes of coupled and uncoupled cases with reference literature results. Additionally, a boundary data transfer application is presented to extend the capabilities of the coupling algorithm to coupled applications with separate domains. In this problem, the two domains share interfaces and boundary values on specific fields as fluxes are exchanged between the two numerical codes.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

Blisks subjected to rough machining for channel creation must undergo finishing processes, and such processes must achieve the required tolerance limits. A high-quality surface finish and predictable long tool life are critical for the finish milling of blisks. Accordingly, the aim of this study was to optimize parameters for the finish machining of an Inconel 718 alloy monolithic blisk. Ball-cone mills were used to machine the blade surface at a constant depth. A sensory tool holder was used to collect cutting force signals during machining, and a digital microscope was used to examine tool wear. The surface texture measuring instrument was used to measure blisk blade surface roughness to evaluate processing quality. This study manipulated two cutting parameters, namely cutting speed and feed per tooth, and investigated their effects. The relationship between cutting conditions and machining efficiency was analyzed. According to the experimental results, we identified a set of optimal parameters for marginal tool wear and fast cutting speeds and then estimated the corresponding tool life by using the derived parameters.

We will demonstrate that the photon energy density parameter Ωγ of the universe can be derived exactly in Rh = ct cosmology. We find that it must be Ωγ = 1/5760π ≈ 5.52621330180192× 10^(−5). This indicates that there is no uncertainty in the radiation density within at least somesub-classes of Rh = ct cosmology.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

The assessment of concrete structures' durability in chlorine environments is significantly impacted by the uncertainty inherent in existing durability models. It introduce an integrated approach for updating these models, based on detection information of existing structures. This approach narrows the gap between theoretical predictions and observed structural durability. Specifically, we refine the probability model of critical chloride content by analyzing steel bar corrosion sample proportions, using Bayesian theory for greater accuracy. The enhanced model enables more reliable life expectancy prediction, forming a solid foundation for maintaining and strengthening existing structures.This method was demonstrated through a case study of a reinforced concrete industrial building with a service life of 12 years.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

The objectives of this study were to evaluate fixed risk factors associated with PWM and to estimate genetic parameters for PWM. A total of 927 birth records from a mixed population of purebred and crossbred Boer and Spanish goats born between 2016 and 2023 at the International Goat Research Center (IGRC) were used for this study. Four binary traits were studied: D0-3 (death within 3 days after birth), D4-60 (death between 4 and 60 days), D61-90 (death between 61 and 90 days), and D0-90 (death within 90 days). Logistic regression models were used to evaluate the risk factors associated with PWM traits. Bayesian threshold models and Gibbs sampling were used to estimate the genetic parameters. Birth weight, season, litter size, sex, dam age, breed, and heterosis were found to be significantly associated with at least one of the PWM traits. Heritability estimates were 0.263, 0.124, 0.080, and 0.207, for D0-3, D4-60, D61-90, and D0-90, respectively. The genetic correlations between the studied traits ranged from 0.892 (D0-3 and D0-90) to 0.999 (D0-3 and D61-90). These results suggest that PWM in goats is influenced by both non-genetic and genetic factors and can be reduced by management, genetic selection, and crossbreeding approaches.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

The impact of systemic vascular resistance (SVR) in hypertrophic (HCM) and amyloid cardio-myopathies has been seldom investigated. We studied pressure-strain loop derived myocardial work (MW) indices and SVR in patients with either sarcomere HCM or wild type transthyretin cardiac amyloidosis (ATTR), presented with heart failure and preserved left ventricular ejection fraction (HFpEF) at the outpatient cardiology units at Messina and Catania University Hospitals (Italy). Patients were in sinus rhythm and needed to have good transthoracic ultrasound imaging quality to undergo transthoracic strain-echocardiography. Other than conventional parameters, SVR and GWI (global work index) were measured. Based on cross-tabulation (a way to assess the ventricular-arterial coupling), the patients were then classified in 4 classes according to the cut-off values suggested by previous studies of 1,440 dyne/s/cm-5 for SVR (Stefadouros et al., 1973) and 1576 mm Hg% for GWI (Olsen et al., 2022). Sixty patients, 30 in each group, aged 61±16 years, 78% males, were studied. HCM were younger than ATTR patients and in a better clinical status (23% HCM vs 77% ATTR were NYHA class 3, p<0.001). Overall, 51 patients (85%) showed high SVR, of whom 21 were HCM (70%) and 30 ATTR (100%) (p<0.005). Both, SVR and GWI were impaired (the poorest class C) in 43% HCM patients (with greater left ventricular concentric hypertrophy) vs 93% of ATTR patients (in advanced NYHA class) (p<0.001). In conclusion, assessing SVR and GWI in HFpEF patients with HCM or ATTR can help clinicians to interpret the pathophysiological and clinical features of such complex diseases.

Voltage-gated potassium (Kv) channels and hyperpolarization-activated cyclic nucleotide-gated (HCN) channels share similar structures but have opposite gating polarity. Kv channels have a strong coupling ( &gt;109) between the voltage sensor (S4) and the activation gate: when S4s are activated the gate is open to &gt;80%, but when S4s are deactivated, the gate is open &lt; 10-9 of the time. Using noise analysis, we show that the coupling between S4 and the gate is &lt; 200 in HCN channels. In addition, using voltage clamp fluorometry, locking the gate open in a Kv channel drastically altered the energetics of S4 movement. In contrast, locking the gate open or decreasing the coupling between S4 and the gate in HCN channels had only minor effects on the energetics of S4 movement, consistent with a weak coupling between S4 and the gate. We propose that this loose coupling is a prerequisite for the reversed voltage gating in HCN channels.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

It has been known that dimensional constants such as ℏ, c, G, e, and k are merely human constructs whose values and units vary depending on the chosen system of measurement. Therefore, the time variation of dimensional constants lacks operational significance due to their dependence on them. It is well-structured and represents a valid discussion. However, this fact only becomes a meaningful debate within the context of a static or present universe. As well-established theoretically and observationally, the current universe is undergoing accelerated expansion, wherein dimensional quantities, like the wavelength of light, also experience redshift phenomena elongating over cosmic time. In other words, in an expanding universe, dimensional quantities of physical parameters vary with cosmic time. From this perspective, there exists the possibility that dimensional constants, such as the speed of light, could vary with the expansion of the universe. In this review paper, we contemplate under what circumstances the speed of light may change or remain constant over cosmic time, and discuss the potential for distinguishing these cases observationally.

The Source Region of the Yellow River (SRYR), renowned as the "Water Tower of the Yellow River", serves as an important water conservation domain in the upper reaches of the Yellow River, significantly influencing water resources within the basin. Based on the Weather Research and Forecasting (WRF) Model Hydrological modeling system (WRF-Hydro) model, the key variables of the atmosphere-land-hydrology coupling processes over the SRYR during the 2013 rainy season are analyzed. The investigation involves a comparative analysis between the coupled WRF-Hydro and the standalone WRF simulations, focusing on the hydrological response to the atmosphere. The results reveal that the WRF-Hydro model's proficiency in depicting streamflow variations over the SRYR, yielding a Nash Efficiency Coefficient (NSE) of 0.44 and of  0.61 during the calibration and validation periods, respectively. Compared to the standalone WRF simulations, the coupled WRF-Hydro model demonstrates enhanced performance in soil heat fluxes simulations, reducing the mean Root Mean Square Error (RMSE) of surface soil temperature by 0.96 K and soil moisture by 0.01 m\textsuperscript{\textsuperscript{3}}/m\textsuperscript{\textsuperscript{3}}. Furthermore, the coupled model adeptly captures the streamflow variation characteristics with the NSE of 0.33. This underscores the significant potential of the coupled WRF-Hydro model for delineating coupled atmosphere-land-hydrology processes in regions characterized by cold climates and intricate topography.

Cosmography, as an integral branch of cosmology, strives to characterize the Universe without relying on pre-determined cosmological models. This model-independent approach utilizes Taylor series expansions around the current epoch, providing a direct correlation with cosmological observations and the potential to constrain theoretical models. Various observable quantities in cosmology can be described as different combinations of cosmographic parameters. Furthermore, one can apply cosmography to models with a varying speed of light. In this case, the Hubble parameter can be expressed by the same combination of cosmographic parameters for both the standard model and varying speed of light models. However, for the luminosity distance, the two models are represented by different combinations of cosmographic parameters. Hence, luminosity distance might provide a method to constrain the parameters in varying speed-of-light models.

The manuscript presents the applicability of the Gumbel distribution in the frequency analysis of extreme events in hydrology. The advantages and disadvantages of using the distribution are highlighted, as well as recommendations regarding its proper use. A literature review was also carried out regarding the methods of estimating the parameters of the Gumbel distribution. Thus, for the verification of the methods, case studies are presented regarding the determination of the maximum annual flows and precipitations using nine methods for parameter estimation. The influence of the observed data lengths on the estimation of the statistical indicators, the parameters and the quantiles corresponding to the field of low annual exceedance probabilities (p <1%) is also highlighted. The results are compared to those obtained with the Generalized Extreme Value distribution, respectively the Burr and the Wakeby distributions with parameters estimated using the L-moments. The results highlight and reaffirm the statistical, mathematical and hydrological recommendation regarding the avoidance of using the Gumbel distribution in Flood Frequency Analysis and its use with reservations in the case of maximum precipitation, especially when the statistical indicators of the analyzed data are not close to the characteristic ones and unique to the distribution.

One objective of this paper is to investigate bifurcation of solutions of Ornstein-Zernike equation in liquid state theory for the gas-liquid coexistence region of simple fluids. The analysis uses a discrete form of the Ornstein-Zernike equation in real space, together with a closure relation which provides nearly self consistent thermodynamic properties of fluids governed by interaction potentials like the Lennard-Jones potential. Accurate asymptotic forms of correlation functions are incorporated in the real space algorithm so as to mitigate the influence of cutoff length used in the discrete approximations. It is found that there is no spinodal on the vapor side on a sub-critical isotherm. But there are fold bifurcation points on the vapor and liquid sides together with a 'no-real-solution-region' in between. This is followed by a region of negative compressibility extending up to the spinodal on the liquid side. The emerging picture is quite similar to that in the case of the hypernetted-chain-closure. It is also found that complex solutions connect the physical solutions that exist outside the 'no-real-solution-region' as well as in region of negative compressibility. The second objective of the paper, in the light of bifurcation scenario, is to evolve an interpretation of the coupling-parameter expansion of correlation functions pertaining to the region of negative compressibility. It is shown that the expansion provides an accurate description of results of the restricted ensembles, implied in mean field theories and simulation methods. Bifurcation of singlet density to inhomogeneous distributions at a spinodal is also established using a simple equation, which uses the direct correlation function. Thus the paper reestablishes the fact that restriction to a homogeneous singlet density is the root cause of all inconsistencies found in the gas-liquid coexistence region.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

The hard open problem of finding the lower bound for the Fokker Planck Kolmogorov’s time-dependent controller parameter probability density function is addressed for the first time in literature in this work. This revolutionary exposition will put control theory and other related inter-disciplinary fields to a higher level towards contemporary control theory. Notably, based on the influential role of control theory in both engineering and industry, this paper will be of great value to all engineering and industry professionals who seek to know more about advanced trends within control theory settings. On the other remit of the spectrum, Fokker Planck Kolmogorov(FPK) equations are of high importance to physicists as well as mathematicians, based on their multiple applicability to multi-interdisciplinary fields of human knowledge, and beyond. So, this by default adds more taste and credibility to this study. Concluding thoughts are included at the end of the work along with a difficult outstanding problem and the direction of future work.

This work is the first in literature to tackle the difficult open problem of determining the upper bound and threshold theorem for the TDCDP (time-dependent controller parameter) of the (Fokker Planck Kolmogorov) probability density function. This revolutionary exposition will put control theory and other related inter-disciplinary fields to a higher level towards contemporary control theory. Notably, based on the influential role of control theory in both engineering and industry, this paper will be of great value to all engineering and industry professionals who seek to know more about advanced trends within control theory settings. On the other remit of the spectrum, Fokker Planck Kolmogorov(FPK) equations are of high importance to physicists as well as mathematicians, based on their multiple applicability to information theory, graph theory, data science, finance, economics, and beyond. So, this by default adds more taste and credibility to this study. This leads by nature to introducing a different flavor to this ground-breaking research by highlighting the impact of Fokker Planck Kolmogorov(FPK) to revolutionize crypocurrency,which have received its name because it uses encryption to verify transactions, a new debatable digital payment system that doesn't rely on banks to verify transactions. It’s a peer-to-peer system that can enable anyone anywhere to send and receive payments. The paper ends with closing remarks combined with some challenging open problems and the next phase of research.

Oscillons, fundamental to various physical domains, are examined in-depth in this paper. From Josephson junctions in superconducting circuits to classical and quantum field theories, oscillators reveal profound insights into diverse phenomena. The study primarily focuses on oscillons, distinctive field configurations with enduring localization, establishing intriguing connections with well-known models like the Sine-Gordon breather. Surprising parallels in the weak coupling limit illuminate the rich dynamics of oscillators. A semi-classical quantization method, discretizing the field into spatially homogeneous regions, exposes stability angles, providing insights into the quantum nature of oscillons. The application of this quantization framework to specific cases, including the Sine-Gordon breather, showcases its versatility. The results offer a comprehensive perspective on the quantization of oscillons, unraveling the intricate interplay between classical and quantum dynamics. In conclusion, this paper provides a profound exploration of quantum oscillators, unveiling novel connections and presenting a rigorous quantization framework. The gained insights contribute significantly to the broader understanding of oscillatory systems and their pivotal role in diverse physical phenomena.

Based on three assumptions of our 4G model of final unification, we have developed simple logics for estimating the unified atomic mass unit, atomic electrochemical equivalents, Faraday constant and Avogadro number. We appeal the science community to review the following points. 1) Unified atomic mass or energy unit can be considered as ‘average rest energy of nucleons minus average binding energy per nucleon of all atomic nuclides plus electron rest energy’. 2) Electrochemical equivalent of any atomic ion is nothing but the ratio of its mass to its charge. 3) Faraday charge is nothing but the ratio of elementary charge to unified atomic mass unit. 4) Faraday mass can be considered as the inverse of Faraday charge. 5) Avogadro number is nothing but the inverse of unified atomic mass unit. 6) Number of atoms per kg can be called as Kg-mole and number of atoms per gram can be called as gram-mole. Following our 4G model, starting form A=5 to 340, for isobars, ‘average binding energy per nucleon’ having maximum binding energy can be estimated with a simple relation of the form, BE/A=A^-1[1-(0.5+0.000935A²)-A^1/3]10.1MeV. It needs a review and fine tuning.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

In this paper we address the approximation of the coupling problem for the wave equation and Maxwell's equations of electromagnetism in the time domain in terms of the electric field, by means of a nodal linear finite-element discretization in space, combined with a classical'explicit finite-difference scheme for the time discretization. Our study applies to the particular case where the dielectric permittivity has a constant value outside a sub-domain, whose closure does not intersect the boundary of the domain where the problem is defined. Inside this sub-domain Maxwell's equations hold. Outside this sub-domain the wave equation holds, which may correspond to the Maxwell's equations with a constant permittivity under certain conditions. We consider as a model the case of first order absorbing boundary conditions. Optimal error estimates that hold in natural norms under reasonable assumptions are given, among which lies a typical CFL condition for hyperbolic equations.

An exposition is undertaken to reveal the significant impact of the time-dependent root parameter, on the stability of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing system. This opens new grounds to stability analysis of non-stationary queueing systems. Potential PSFFA applications of IoT are highlighted.

Modern power systems are confronted with a spread concern on the frequency stability issue due to the widespread integration of randomly fluctuating renewable resources. To address the above concern, this work introduces a load frequency control (LFC) scheme based on a hydrogen based energy-storage unit and a parameter tuning strategy for fractional-order proportional-integral-derivative (FOPID) controller. Firstly, a two-area interconnected power system (IPS) model, including thermal, hydro, solar, wind, gas power generator, and hydrogen based energy-storage unit, is established. Then, a FOPID controller is designed for this IPS model, and an improved gradient-based optimizer (IGBO) is developed to adaptively regulate the parameters of the FOPID controllers. Finally, the effectiveness of the offered LFC scheme are tested through load disturbance and renewable energy fluctuations test scenarios, and provides comparison and robustness analysis among different schemes. The test results validated that the offered LFC scheme can effectively suppress the frequency fluctuations of IPS and has excellent robustness.

Exploring the spatio-temporal differentiation characteristics and coupling coordination relationship of the composite ecosystem of urban agglomerations is of great significance for promoting the synergistic development and integration construction of urban agglomerations. This paper is based on LUCC data, DEM, temperature, precipitation and other multi-source data, taking the central Yunnan urban agglomeration as an example. The entropy weight method is first used to determine the comprehensive weights to evaluate the regional economic and social development level. Then, the InVEST (Integrated Valuation of Ecosystem Services and Trade-offs)model was used to quantitatively calculate and analyze the spatial and temporal evolution characteristics of the four ecosystem services, including water conservation, soil conservation, carbon sequestration services, and habitat quality. The coupling coordination model was used to quantitatively analyze the evolution of the coupling coordination of the composite ecosystems in the central Yunnan urban agglomeration during the period of 2010-2020, and to reveal its development law. The results show the following: ①During the study period, the socio-economic subsystems in central Yunnan urban agglomeration demonstrated an outward radiative growth from Kunming City, marked by underdeveloped sub-centers and prevalent low-level areas. ②Trends in ecosystem services varied, with water and soil conservation showing fluctuating increases, carbon sequestration remaining stable, and habitat quality declining. The integrated ecosystem services critically important zone is mainly located in the northeastern region and southwestern edge of the study area. ③Economic, social and ecological subsystems are highly coupled, with consistent overall development trends and strong interactions. ④The increase in the degree of harmonization amounted to 7.82%, with lagging subsystems varying in different degree of harmonization subregions. The study can provide a scientific basis for urban agglomerations to formulate scientific and reasonable development policies, promoting regional sustainable development and optimizing the spatial pattern of the national territory.

Modelling diameter distribution is an integral part of forest management. It requires the use of a suitable probability density function or cumulative distribution function with the appropriate fitting method. In this study, we compared the suitability of eight probability density functions fitted by derivative and optimization methods used for diameter distribution estimation of forest stands. The derivation and optimization were used on A Charlier, beta, generalized beta, gamma, Gumbel, Johnson’s SB, and Weibull (2 and 3-parameter). We used data from 167 permanent sample plots from Atlantic forest (Quercus robur) and 59 temporary sample plots from tropical forests (Tectona grandis). The quality of the fits was evaluated with different indices such as Kolmogorov–Smirnov, Cramer-von Mises, mean absolute error, bias and mean squared error. The results showed Johnson’s SB function was more suitable for describing the diameter distribution of the stands. Johnson’s SB, 3-parameter Weibull and generalized beta had consistent performance regardless of the fitting methods. The quality of fits produced by gamma, Gumbel and 2-parameter Weibull was poor.

After a survey on polymer plasticization theories and conventional criteria to evaluate polymer-plasticizer compatibility through the solubility parameter, an attempt to create a polymer-plasticizers polarity scale through solvatochromic dyes has been made. Since the Reichardt’s ET(30) dye is insoluble in rubber hydrocarbon polymers like polyisoprene, polybutadiene and styrene-butadiene copolymers and is not also useful for the evaluation of the hydrocarbons and ester plasticizers, the Nile Red solvatochromic dye was instead used extensively and successfully for this class of compounds. A total of 53 different compounds were evaluated with the Nile Red dye and wherever possible also with the ET(33) Reichardt’s dye. A very good correlation was then found between the Nile Red scale E(NR) and the Reichardt’s ET(30) scale for this class of compounds focusing on diene rubbers and their typical hydrocarbons and new esters plasticizers. Furthermore, the E(NR) scale shows also a reasonable correlation with the total solubility parameter calculated according to the Van Krevelen method. Based on the above results, some conclusion was made about the compatibility between the diene rubbers and the conventional plasticizers as well as some new and green plasticizer proposed for the rubber compounds.

This research examines how rainfall and mining affect the slope damage resulting from the transition from open-pit mining to underground mining. Using unmanned aerial vehicle (UAV), the Huangniu slope of Dexing Copper Mine was fully characterized, and experiments were conducted on rock samples from appropriate sites. First, the mechanical properties of the samples were measured. Then, the parameters of the similarity simulation experiments were derived based on the similarity theory. Subsequently, the rainfall, rock slope, data acquisition and monitoring systems were designed. Finally, the rock mass failure with different slope angles was analyzed, and the deformation and damage patterns under the coupling effect were obtained. The results show that rainfall increases pore water pressure and moisture content. Rainfall and slope-slip water have more impact on the open-pit platform. The pore water pressure values on the upper rock mass rise faster than inside. In the open-pit mining stage, the rock mass shifts slightly to the upper left. In the room mining stage, vertical fractures and goaf sinking occur. The fractures above the mine room form a semi-ellipse. In the pillar mining stage, the overlying rock displacement is evident, and fractures persist. In the continuous pillar mining stage, the overlying rock collapses massively. The 65° slope model is the most damaged, while the 55° slope model is the least damaged. The results also suggest that the UAV guides sample selection.

Despite being small and simple structured in comparison to their victims, virus particles have the potential to harm severly and even kill highly developed species such as humans. To face upcoming virus pandemics, detailed quantitative biophysical understanding of intracellular virus replication mechanisms is inevitable. Unveiling the relationship of form and function might allow to determine putative attack points relevant for the systematic development of direct antiviral agents (DAA) and potent vaccines. Biophysical investigations of spatio-temporal dynamics of intracellular virus replication so far are rare. We are developing a framework to allow for fully spatio-temporal resolved virus replication dynamics simulations based on partial differential equations models (PDE) and evaluated with advanced numerical mathematical methods on leading supercomputers. This study presents an advanced highly nonlinear model of the genome replication cycle of a specific RNA virus, the Hepatitis C virus (HCV). The diffusion-reaction model mimics the interplay of the major components of the viral RNA (vRNA) cycle, namely non structural viral proteins (NSP), vRNA and a generic host factor. Technically, we couple surface PDEs (sufPDEs) on the 3D embedded 2D Endoplasmatic Reticulum (ER) manifold with PDEs in the 3D membranous web (MW) and cytosol volume. (The MWs are the replication factories growing on the ER induced by NSPs.) The sufPDE/PDE model is evaluated at realistic reconstructed cell geometries which are based on experimental data. The simulations couple the effects of NSPs which are restricted to the ER surface with effects appearing in the volume. The volume effects include the host factor supply from the cytosol and the MW dynamics. Special emphasis is put to the exchange of components between ER surface, MWs and cytosol volume. As the vRNA spatial properties are not fully understood so far in experiment, the model allows for vRNA both restricted to the ER and moving in the cytosol. The visualization of the simulation resembles a look into some sort of fully 3D resolved “in silico microscopes” to mirror and complement in vitro / in vivo experiments for the intracellular vRNA cycle dynamics. The output data are quantitatively consistent with experimental data and provoke advanced experimental studies to validate the model.

During deep-sea mining, the heavy metals pollutants can cause contamination in the marine environment. In this paper, the multiphasic coupling model is established to describe the heavy metal migration process during deep-sea mining, which takes the effects of convection-diffusion, adsorption-desorption and sedimentation-resuspension of heavy metals in the aquatic environment into full consideration. Due to the advantages of Lattice Boltzmann method, it is adopted to numerically solve the multiphasic coupling model and achieve the simulation for heavy metal migration process during deep-sea mining. In addition, taking Cadmium as an example, the concentration variations are discussed and analyzed in detail. Based on the established model and Lattice Boltzmann method, the concentration distribution of heavy metals can be accurately described to provide the reasonable bases for the evaluation of marine environmental protection.

On February 24, 2022 Russia started the full-scale invasion of Ukraine, which created an unprecedented number of refugees. To estimate the influence of this humanitarian disaster on the COVID-19 pandemic dynamics, the averaged daily numbers of cases and reproduction numbers in Ukraine, the UK, Poland, Germany, the Republic of Moldova, and in the whole world were calculated for the period February-April 2022. The registered numbers of cases were compared with ones calculated with the use of the generalized SIR-model and corresponding parameter identification procedure for the previous epidemic waves in Ukraine, Poland, Germany, and the world. Since before February 24, 2022 the estimation of the number of infectious persons per capita in Ukraine 3.6 times exceeded the global figure, the increase of the number the new cases and the pandemic duration was expected. In March 2022 the increase of the averaged number of new cases in the UK, Germany, and worldwide was visible. A simple formula to estimate the effective reproduction number based on the smoothed accumulated numbers of cases is proposed. The results of calculations agree with the figures presented by John Hopkins University and demonstrate a short-term growth of the reproduction number in the UK, Poland, Germany, Moldova, and worldwide in March 2022.

This article presents a concise survey of basic discrete and semi-discrete nonlinear models which produce two- and three-dimensional (2D and 3D) solitons, and a summary of main theoretical and experimental results obtained for such solitons. The models are based on the discrete nonlinear Schrödinger (DNLS) equations and their generalizations, such as a system of discrete Gross-Pitaevskii (GP) equations with the Lee-Huang-Yang corrections, the 2D Salerno model (SM), DNLS equations with long-range dipole-dipole and quadrupole-quadrupole interactions, a system of coupled discrete equations for the second-harmonic generation with the quadratic (χ⁽²⁾) nonlinearity, a 2D DNLS equation with a superlattice modulation opening mini-gaps, a discretized NLS equation with rotation, a DNLS coupler and its PT-symmetric version, a system of DNLS equations for the spin-orbit-coupled (SOC) binary Bose-Einstein condensate, and others. The article presents a review of basic species of multidimensional discrete modes, including fundamental and vortex solitons, their bound states, gap solitons populating mini-gaps, symmetric and asymmetric solitons in the conservative and PT-symmetric couplers, cuspons in the 2D SM, discrete SOC solitons of the semi-vortex and mixed-mode types, 3D discrete skyrmions, and some others.

Advanced methods of treatment are needed to fight the threats of virus-transmitted deseases and pandemics. Often they are based on an improved biophysical understanding of virus replication strategies and processes in their host cells. For instance, an essential component of the replication of the Hepatitis C virus (HCV) proceeds under the influence of non-structural HCV proteins (NSPs) that are anchored to the endoplasmatic reticulum (ER), such as the NS5a protein. The diffusion of NSPs has been studied by in-vitro fluorescence recovery after photobleaching (FRAP) experiments. The diffusive evolution of the concentration field of NSPs on the ER can be described by means of surface partial differential equations (sufPDE). Knodel et al, Viruses 2018, 10, 28 estimated the diffusion coefficient of the NS5a protein by minimizing the discrepancy of an extended set of sufPDE simulations and experimental FRAP time series data. Here, we provide a scaling analysis of the sufPDEs that describe the diffusive evolution of the concentration field of NSPs on the ER. This analysis provides an estimate of the diffusion coefficient that is based only on the ratio of the membrane surface area in the FRAP region and its contour length. The quality of this estimate is explored by comparison to numerical solutions of the sufPDE for a flat geometry and for ten different 3D embedded 2D ER grids that are derived from fluorescence z-stack data of the ER. Finally, we apply the new data analysis to the experimental FRAP time-series data analyzed in our previous paper, and we discuss the opportunities of the new approach.

Bipyridine and its related compounds are starting materials or precursors for a variety of valuable substances, such as biologically active molecules, ligands for catalysts, photosensitizers, viologens, and supramolecular architectures. Therefore, it is important to classify the synthesis methods and know their characteristics. Representative examples include the methods using homo- and heterocoupling of pyridine derivatives in the presence of catalyst. Because bipyridine compounds have a high ability to coordinate with metal centers, a decrease in catalytic activity and yield is often observed in the reaction system. To address this issue, the review provides insight into recent advances in bipyridine synthesis using metal complexes under both homogeneous and heterogeneous conditions. Moreover, the review also sheds light on strategies for bipyridine synthesis involving sulfur and phosphorous compounds. These alternative pathways offer promising avenues for overcoming challenges associated with traditional-catalyzed methods, providing a more comprehensive understanding of the synthesis landscape.

Improper design of friction pendulum bearings can lead to poor seismic reduction performance and may result in the failure of local vulnerable components. And the parameter design of friction pendulum bearings mainly relies on experience and verification calculations at present. This paper proposes an adaptive genetic algorithm considering the overall evolution state of the population, adjusting crossover and mutation probabilities adaptively based on individual fitness and population diversity. Compared to traditional algorithms, it exhibits better global search capabilities and convergence efficiency. Combining the improved genetic algorithm with finite element models, a parameter optimization method is proposed. The parameters of friction pendulum bearings are optimized, providing reference for the design of seismic isolation devices.

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

In recent years, wireless power transfer (WPT) has progressed rapidly in both theory and commercialization abroad. However, existing research into WPT coil design for low-power devices is limited. This paper investigates coil structure using printed circuit board (PCB) for magnetic resonant coupling WPT to address this gap. Specifically, the impacts of key geometric parameters on the coil quality factor and coupling coefficient are analysed through models and simulations. Equivalent PCB coils were formed for mutual inductance models, and four basic compensation circuits were analysed. The impacts of changes in coil thickness, line width, turn spacing, and number of turns on the quality factor of PCB coils were analysed with a fixed outer diameter of the coil. In this paper, to mitigate the coil offset while retaining PCB manufacturing simplicity for practical uses, a dual layer PCB coil structure is proposed. The structure optimizated PCB coil could offer remarkable improvements in the WPT system for low power electronic devices.

Multi-channel and multi-parameter near-infrared spectrometers (NIRS) have gradually become a new research direction and hot spot due to their ability to provide real-time, continuous, comprehensive indicators of multiple parameters. However, multi-channel and multi-parameter detection may lead to crosstalk between signals. There is still a lack of benchmarks on the evaluation of reliability, sensitivity, stability and response consistency of the NIRS instrument. In this study, a set of test methods (the ink drop test, multi-channel crosstalk test and multi-parameter crosstalk test) for analysis crosstalk and verifying the reliability of NIRS were conducted to test experimental verification on a multi-channel (8-channel), multi-parameter (4-parameter) NIRS instrument independently developed by our team. Results show that these tests can be used to analyze the signal crosstalk and verify the reliability, sensitivity, stability and response consistency in the NIRS instrument. This study contributes to the establishment of benchmarks for the NIRS instrument crosstalk and reliability testing. These novel tests have the potential to become the benchmark for the NIRS instrument reliability testing.

The exchange coupling between two ferromagnetic thin films, one with magnetically hard and the other with soft phases, separated by a thin non-magnetic layer is studied. Nd-Fe-B/ Ti / Fe thin film heterostructures were fabricated using DC magnetron sputtering on Si substrates which were heated in situ at 650°C using a house-built vacuum-compatible heater. The effect of the thickness of the Ti buffer layer and the annealing temperature on the formation of various phases of NdFeB was investigated. The effect of the thickness of the non-magnetic Ti spacer layer on the exchange coupling strength between the hard phase Nd-Fe-B ferromagnetic thin layer and the soft phase transition metal Fe layer was experimentally investigated. Hysteresis loops of multilayer thin films indicate an antiferromagnetic coupling was observed when the thickness of the spacer layer was 2 nm. This is within the range of antiferromagnetic coupling calculation based on RKKY theory predictions.

The extreme environmental issues and the resulting needs to save energy have turned the attention to electrification of energy applications. One of the key components involved in energy efficiency improvements is the appropriate conception and manufacturing of electric machines. This paper overviews the electromagnetic analysis governing the behavior of permanent magnets that enabled substantial efficiency gains in recent electric machine developments. Particular emphasis is given to model the properties and losses developed in permanent magnets in the emerging high speed applications. In addition, the investigation of properties and harmonic losses related to ferromagnetic materials constituting the machine magnetic circuits are equally analyzed and discussed. The experimental validation of the implemented methodologies and developed models with respect to the obtained precision is reported. The introduction of mixed numerical techniques based on the finite element method intended to appropriately represent the different physical phenomena encountered is outlined and discussed. Finally, fast and accurate simulation techniques including aggregated lumped parameter models considering harmonic losses associated with inverter supplies are commented.

In this paper, we present a new parametric class of optimal fourth-order iterative methods to estimate the solutions of nonlinear equations. After the convergence analysis, we study the stability of this class by using the tools of complex discrete dynamics. This allows us to select those elements of the class with lower dependence on initial estimations. We verify by means of numerical tests that the stable members on quadratic polynomials perform better than the unstable ones, when applied to other non-polynomial functions. We also compare the performance of the best elements of the family with known methods, such as the schemes by Newton or Chun, among others, showing robust and stable behaviour.

Electromagnetic cloaking approach is employed with the intention to curb the destructive effects of mutual interference for rectangular and circularly shaped patch antennas situated in a tight spacing (sub-wavelength separation is employed). Primarily, we show that by coating the top surface of each patch with an appropriately designed metasurface, it is possible to considerably reduce the mutual coupling between the said antennas. We also demonstrate that, despite the close proximity of these patches, the individual radiation characteristic of each antenna is reinstated to emulate their performance in an isolated scenario. Furthermore, the cloak construct is extended to a tightly spaced, interleaved linear patch antenna array configuration and it is shown that the coated metasurfaces successfully enhance the performance of each array in terms of their matching characteristics, total efficiencies as well as their far-field realized gain patterns for a broad range of beam-scan angles. The decoupling and cloaking action of these metasurfaces are demonstrated by various full-wave numerical simulation results. We believe that the simple planar structure of our metasurface design (according to simulation models) makes it feasible for fabrication and the fact that it is used to accomplish cloaking of an electrically large antenna surface, makes it unique in itself.

While considering the sensitivity over the parameter optimization, it is essential to determine which parameters have the most significant implications on model performance. This study focuses on the baseflow recession constant as one of the independent basin parameters to forecast low flows, perform hydrograph analysis, and calibrate rainfall-runoff models for significant improvement. Prior studies examined that the optimization of data adjustment parameters can improve the hydrological model performance and determine the minimum acceptable data length for data scarce regions using the Xinanjaing model. However, it is essential to pay special attention to the sensitivity of the recession constant, which can also impact the model performance during the data scarcity. Therefore, this study extends the research to comprehend the recession constant sensitivity over data adjustment parameters in the shorter datasets leading to more reliable parameter estimation. In terms of that, this study explores how recession constant affects hydrological parameter estimation on annual scale while keeping data adjustment parameters constant in continuous hydrological modeling, employing the Xinanjiang (XAJ) model as a case study. This study considered two approaches of recession constant (cg); (i) assessing the relationship between cg and the data adjustment parameter (Cep), for the 28-year datasets, (ii) investigating the significant impacts of the sensitivity of cg over Cep in shorter datasets which can affect the estimation of the acceptable minimum data length in the data scarce basins. The study underscores the importance of the recession constant sensitivity for reliable continuous hydrological model predictions, especially in data-scared areas. The study’s outcomes enhance the understanding of the importance of parameter sensitivity and its relationship in conceptual hydrological modeling during the data limitations.

Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

Fabry-Pérto (FP) cavity is the essential component of ultra-stable laser (USL) for gravitational wave detection, which couples multi-physic (Optical/Thermal/Mechanics) fields and requires ultra-high precision. To satisfy the requirements of precise and efficient design, a multi-physic coupling optimization method for fixing cubic FP cavity based on data learning is proposed. A multi-physic model for the cubic FP cavity is established and the performance is obtained by finite element analysis. The key performance indices (V, wF, wF) and key design variables (d, l, F) are determined considering the features of the FP cavity. The 49 sets of data by orthogonal experiment are acquired for the establishment and comparison of different data learning models (NN, RSF, KRG). The result turns out that the neural network has the best performance. Based on NSGA-II, the Pareto optimal front is obtained and the optimal combination of design variables is finally determined as {5,32,250}. The performance after optimization has proven to be a great improvement, of which the displacement under the fixing force and vibration test are decreased by more than 60%. The optimization strategy can not only help the design of the FP cavity but also enlighten other optimization fields.

The limitations of conventional sensors have made phased array antennas increasingly crucial for gathering information and communication applications in intelligent transportation systems. Compact cylindrical arrays, in particular, are favored for their ability to achieve azimuth angle scan. However, the substantial mutual coupling effect between elements on curved surfaces and its implication in these arrays remains unclear, which is a crucial factor to consider when such arrays are used for multibeam applications. This study investigated the effect of mutual coupling in a dual-slant-polarized cylindrical array. The results showed that mutual coupling is essential for achieving an ultra-wide bandwidth. Mutual coupling is predominantly observed among elements that are closely positioned. The study also analyzes the impact of mutual coupling on scan impedance and radiation characteristics for multibeam applications and reveals that these arrays exhibit robust multibeam capability, hence having great potential for use in intelligent transportation systems.

Many Western studies have indicated that older women are generally more vulnerable in terms of mobility compared to older men, particularly regarding driving. However, the situation may differ in the context of China. This study, based on activity diaries and semi-structured inter-views, focuses on the spatiotemporal behavior of older adults in Tianjin and explores how the constraints posed by activity companions (in terms of type, size, and composition) shape the mo-bilities of older men and women, including activity locations, travel distances, and transporta-tion modes. The key findings are as follows: First, older women are more engaged with their families due to a higher percentage and longer duration of activities spent with family members. Second, older men tend to have more concentrated travel distances near their homes compared to older women. Third, older women exhibit a broader range of activities in different locations and engage in longer-distance leisure travel with family members when compared to older men. In the context of Western literature, this study discusses older women's enhanced social interactions, their earlier retirement in China, and the impact of COVID-19 as factors that help explain these findings. This study contributes to a deeper understanding of accompanied mobilities among Chinese older adults using geographical theory and methods, emphasizing the importance of flexible work schedules for the workforce and the organization of community-based activities to promote the social interactions and mobilities of older adults.

The treatment of critically ill patients remains an evolving and controversial issue. Mechanical circulatory support through a percutaneous approach for the management of cardiogenic shock has taken place in recent years. The combined use of IABP and Impella 2.5 device may have a role to play for this group of patients. A simulation approach may help with a quantitative as-sessment of the achievable degree of assistance. In this paper, we analyse the interaction be-tween Impella 2.5 pump applied as LVAD and IABP using the numerical simulator of the cardi-ovascular system developed in our laboratory. Starting with pathological conditions reproduced using literature data, the simulations were performed setting different rotational speeds for the LVAD and driving the IABP in full mode (1:1) or partial mode (1:2, 1:3 and 1:4). The effects in-duced by drug administration during the assistance were simulated too. The haemodynamic pa-rameters under investigation were: mean aortic pressure, systolic and diastolic aortic pressure, mean pulmonary arterial pressure, mean left and right atrial pressure, cardiac output, cardiac index, left and right ventricular end-systolic volume, left ventricular end-diastolic volume and mean coronary blood flow. The energetic variables considered in the study were: left and right ventricular external work and left and right atrial pressure-volume area. The outcome of our simulations shows that the combined use of IABP and Impella 2.5 achieves adequate support in the acute phase of cardiogenic shock compared to each standalone device. This would allow fur-ther stabilisation and transfer to a transplant centre should escalation of treatment be required.

Interhemispheric and frontoparietal functional connectivity have been reported to increase during explicit information processing. However, it is unclear how and when interhemispheric and frontoparietal functional connectivity interact during explicit semantic processing. Here, we tested the neural coupling hypothesis that explicit semantic processing promotes neural activity in the nondominant right hemispheric areas owing to synchronization with enhanced frontoparietal functional connectivity at later processing stages. We analyzed electroencephalogram data obtained using a semantic priming paradigm, which comprised visual priming and target words successively presented under direct or indirect attention to semantic association. Scalp potential analysis demonstrated that the explicit processing of congruent targets reduced negative event-related potentials, as previously reported. Current source density analysis showed that explicit semantic processing activated the right temporal area during later temporal intervals. Subsequent dynamic functional connectivity and neural coupling analyses revealed that explicit semantic processing increased the correlation between right temporal source activities and frontoparietal functional connectivity in later temporal intervals. These findings indicate that explicit semantic processing increases neural coupling between the interhemispheric and frontoparietal functional connectivity during later processing stages.

In this study, a new empirical equation was established to predict the sedimentation volume resulting from the construction of a multipurpose weir or low-head dam. The study employed a one-dimensional numerical model (STAFF) to investigate the key parameters affecting sedimentation volume. Short-term predictions were conducted through laboratory experiments with movable bed, and the results indicated that dimensionless unit stream power and the Shields parameter exhibited the most significant correlation with dimensionless deposition volume. Using a multiple regression approach, an empirical equation was formulated and validated for predicting sedimentation in the upstream reservoir of the weir.

The development of integrated, compact, and multifunctional photonic circuits is crucial to increase the capacity of all-optical signal processing for communications, data management or microsystems. Plasmonics brings compactness to numerous photonic functions, but its integration into circuits in not straightforward due to insertion losses and poor modes matching. The purpose of this article is to detail the integration strategies of plasmonic structures on dielectric waveguides, and to show through some examples the variety and the application prospect of integrated plasmonic functions.

The relationship between arterial stiffness and oxygen uptake (VO2) in patients with acute myocardial infarction (AMI) remains unclear. We aimed to investigate this relationship and factors contributing to VO2 in patients with AMI. The role of arterial stiffness in cardiac-skeletal muscle coupling during exercise was then elucidated. The exercise capacity via cardiopulmonary exercise testing (CPX), cardio-ankle vascular index (CAVI), and body composition of 101 patients with AMI were measured at discharge. Patients were categorized based on their CAVI into three groups: (i) normal (CAVI: ≤7.9), (ii) borderline (CAVI: 8.0–8.9), and (iii) abnormal (CAVI: ≥9.0). Subsequently, VO2 was compared among these groups. The relationship between the CAVI and peak VO2 (VO2 Peak) during CPX and factors contributing to VO2 Peak were investigated. The abnormal CAVI group had a significantly lower VO2 Peak than the normal and borderline groups. The CAVI was associated with VO2 Peak in patients with AMI. Furthermore, the CAVI was found to be a factor contributing to VO2 Peak. These findings suggest that arterial stiffness in tissue blood distribution and blood supply defines systemic exercise limits in patients with AMI. This suggested that arterial stiffness plays a significant role in cardio-vascular-skeletal muscle coupling.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

The aim of this paper is to deep into the dynamic study of the well known Chebyshev-Halley family of iterative methods for solving nonlinear equations. Our objetives are twofold: one the one hand, we are interested in characterize the existence of extraneous attracting fixed points when the methods in the family are applied to polynomial equations. On the other hand, we are also interested in study the free critical points of the methods in the family, as a previous step to determine the existence of attracting cycles. In both cases, we want to identify situations where the methods in the family have a bad behavior from the root-finding point of view. Finally, and joining these two studies, we look for polynomials for which there are methods in the family where this two situations happen simultaneously. That is, the rational map obtained by applying a method in the Chebyshev-Halley family to a polynomial has both super-attracting extraneous fixed point and super-attracting cycles different to the roots of the polynomial.

For the polymer electrolyte fuel cell (PEFC), the separator thickness plays an important role to determine the weight, the volume and the costs of the PEFC. In addition, thermal management, i.e. temperature distribution is also important for the PEFC system to obtain higher performance. However, there were few reports investigating the relationship between the temperature distribution and the power generation performance such as current density distribution of PEFC operated at higher temperature (HT-PEFC). The aim of this study is to clarify the impact of separator thickness on the relationship between the temperature distribution and the current density distribution of HT-PEFC. This study has also investigated the impact of separator thickness on the relationship between the temperature distribution and the gases such as H2, O2 and the current density distribution of HT-PEFC numerically using CFD software COMSOL Multiphysics. The separator thicknesses of 2.0 mm, 1.5 mm and 1.0 mm were studied. In the study, the operation temperature and the relative humidity (RH) of supply gas were also changed. As a result, it was revealed that the optimum separator thickness was 2.0 mm to obtain higher power generation of HT-PEFC. Since the heat capacity in the case of the separator thickness of 2.0 mm was the largest among the separators investigated in this study, the dehydration of PEM and catalyst layer was smaller compared with the thinner separator thicknesses. It was also revealed that the impacts of separator thickness on distribution of gases, e.g. O2, H2O, and current density distribution became larger under higher temperature and lower RH conditions. This study also concluded that the tendency of temperature distribution matched those of O2, H2O and current density distributions.

The carbonation of industrial calcium-rich byproducts such as steel slag demonstrates significant potential for CO2 sequestration. This technique aids in reducing carbon emissions while also promoting waste recycling. Despite its advantages, gaps remain in understanding how steel slag characteristics and operational parameters influence the carbonation process, as well as the underlying mechanism of direct aqueous carbonation. We evaluated the carbonation performance of three types of steel slag at temperatures below 100°C using a gas–liquid–solid reaction system. The slag with the highest CO2 sequestration capacity was chosen for a systematic evaluation of the effects of operating conditions on carbonation efficiency. Thermodynamic analysis indicated that the reactivity of CaO and Ca(OH)2 with CO2 exceeded that of CaO•SiO2 and 2CaO•SiO2. Under conditions of 85°C, a particle size less than 75 μm, an initial CO2 pressure of 0.5 MPa, a liquid-to-solid ratio of 5 mL/g, and a stirring speed of 200 rpm, the steel slag achieved a sequestration capacity (K) of 283.5 gCO2/kg and a carbonation efficiency (ζCa) of 51.61%. Characterization of the slag before and after carbonation using X-ray diffraction, SEM‒EDS, thermogravimetric analysis, and Fourier transform infrared spectrometry confirmed the formation of new carbonates. Mechanistic analysis revealed that the rate-limiting step initially involved the mass transfer of CO2, transitioning to Ca2+ mass transfer as time progressed. Our research provides a viable technique for CO2 capture and a beneficial approach for reutilizing waste steel slag. Furthermore, solid residues after capturing CO2 have the potential for conversion into carbon-negative building materials, offering a sustainable strategy for steel companies and other enterprises with high carbon emissions.

Aryl chlorides and bromides in the presence of NHC palladium hydroxo dimers of the type [{Pd(µ-OH)Cl(NHC)}2] (where NHC = IPr, SIPr, IMes, SIMes) undergo an efficient and selective Sonogashira cross-coupling with terminal acetylenes. For the coupling of 4-chlorotoluene with phenylacetylene TON = 560000 was observed. The procedure enables high-throughput and selective synthesis of a broad spectrum of unsymmetrically substituted 1,2-diarylacetylenes. Nearly a quantitative amount of HCl was detected within cross-coupling products. Water plays the role of the base and is regenerated in the process so that it does not have to be used in stoichiometric amounts (relative to the limiting reactant). Generation of the active Pd(0) complex proceeds via ethanol oxidation.

In order to study the effects of dietary folic acid (FA) supplementation on growth performance and immune status in weanling piglets, a single factorial randomized block design trial with 6 dietary FA levels at 0.35, 0.66, 2.19, 5.18, 7.51 or 10.81 mg/kg was conducted. A total of 108 crossbred (Landrace × Yorkshire) castrated weanling piglets (at 21 d of age) were allocated by body weight into 36 feeding cages (3 piglets/cage), which were allotted randomly into 6 dietary groups (6 cages/group). Piglets were fed ad libitum for 24 days. Blood samples were collected on the 24th day. The growth performance and the immune parameters were measured. Results showed that FA supplementation increased the serum FA level of weaned piglets (p < 0.01), and tended to increase the body weight (BW) at 45 d of age (p < 0.1) and the average daily gain (ADG) from 29 d to 45 d of age (p < 0.1). FA addition improved the feed efficiency (G/F) from 21 d to 45 d of age (p < 0.01), and with significant effects at 21 d to 45 d of age with FA 2.19 or 7.51 mg/kg (p < 0.05). Dietary FA at 0.66 or 2.19 mg/kg increased the serum CD3+CD8+ subset (p < 0.05), decreased the CD3+CD4+ / CD3+CD8+ ratio (p < 0.05); Moreover, FA addition increased the serum IFN-γ level (p < 0.05). In conclusion, the adequate dietary FA is necessary to improve the immunity and growth performance of weaned piglets at 21 d of age. The suitable dietary FA level for immune function from 21 d to 45 d of age was 0.66 mg/kg, while were 6.82 mg/kg from 21 d to 28 d of age and 5.42 mg/kg from 29 d to 45 d of age respectively for feed efficiency.

A new mesogenic non-symmetric dimeric monomer with a terminal olefin function, forming a twist bend nematic (Ntb) as well as a nematic (N) phase was synthesized, using an enhanced synthetic methodology, which avoids isomerization of the terminal double bond in the preparation of the dimer. This monomer was attached to a pentamethyldisiloxane group, resulting in SmA LC phase behaviour of the ensuing material. Linking the monomer to a siloxane main chain resulted in nematic phase behaviour. Detailed studies with the Ntb phase forming dimer DTC5C7 show full miscibility of the dimer and the new LC polymer in the LC state, suggesting that the side-chain LC polymer forms a Ntb phase as the low temperature nematic phase. Copolymerizing the monomer with a cyanobiphenyl based monomer allows to tune the glass transition and phase behavior further.

Bimetallic colloidal CoPt nanoalloys, with a very low platinum content, were successfully synthesized following a modified polyol approach. Powder X-ray diffraction, IR spectroscopy, thermogravimetric analysis, and Transmission Electron Microscopy studies were performed to estimate the crystal structure, morphology and surface functionalization of the colloids respectively, while the room temperature magnetic properties were measured using Vibrating Sample Magnetometer. The particles exhibit excellent uniformity, with a narrow size distribution, and display strong room temperature hysteretic ferromagnetic behavior even in the as-made form. Upon annealing at elevated temperatures, progressive formation and co-existence of exchange coupled both chemically ordered and disordered phases, significantly enhance the room temperature coercivity.

Taking Korla fragrant pear as the research object, single factor testing and water and fertilizer coupling testing were conducted. Under the premise of the drip irrigation mode, the effects of water, nitrogen, and phosphorus on the growth, fruit quality, and yield of Korla Fragrant Pear were studied to provide a theoretical basis for efficient water and fertilizer management. Among them, the single factor test set water, nitrogen and phosphorus as the three factors, and each factor was set at five levels, namely, water (W1, 5460 m3·hm−2;W2, 5880 m3·hm−2;W3,6300 m3·hm−2; W4, 6720 m3·hm−2; W5, 7140 m3·hm−2), nitrogen (N1, 150 kg N·hm−2;N2, 225 kg N·hm−2; N3, 300 kg N·hm−2; N4, 375 kg N·hm−2; N5, 450 kg N·hm−2), phosphorus (P1,75 kg P2O5·hm−2; P2, 150 kg P2O5·hm−2; P3, 225 kg P2O5·hm−2; P4, 300 kg P2O5·hm−2; P5, 375 kg P2O5·hm−2). The results showed that the total nitrogen and total phosphorus contents in leaves under the W3, W4, N3, N4, P3, and P4 treatments were significantly higher than those under other treatments, and the fruit quality was better. Therefore, the W3, W4, N3, N4, P3, and P4 treatments were selected as the water and fertilizer inputs for the water–fertilizer coupling test for Korla fragrant pear. Eight treatments were set up in the water and fertilizer coupling test: Treatment 1 (T1, W3N3P3), Treatment 2 (T2, W3N3P4), Treatment 3 (T3, W3N4P3), Treatment 4 (T4,W3N4P4), Treatment 5 (T5, W4N3P3), Treatment 6 (T6, W4N3P4), Treatment 7 (T7, W4N4) P3), and Treatment 8 (T8, W4N4P4). The results showed that the leaf area index of the T1, T2, T3, and T4 treatments was significantly higher than that of the other treatments at maturity. The T3 treatment resulted in the highest fruit yield, single fruit weight, and primary fruit rate. The results of the grey correlation degree analysis of fruit quality showed that T3 treatment had the highest degree of correlation and ranking of each fruit quality index, indicating that T3 treatment had the highest fruit quality. Detailed investigation of pear tree growth and fruit quality showed that the T3 treatment (375 kg·hm−2 nitrogen application, 225 kg·hm−2 phosphorus application and 6300 m3·hm−2 irrigation) had the best fruit growth and development performance, and the sweet pear fruit quality was the best.

The recognition of coal-rock interface is very crucial for the research in the intelligent production of coal mine. This study investigates the application of terahertz time-domain spectroscopy in the recognition of coal-rock interface, including the identification of coal-rock and coal-rock mixtures, as well as the accurate characterization of coal seam thickness. Terahertz detection was used to obtain the optical parameter information of the pressed pellets prepared by mixing two different kinds of coal and two kinds of rock. Based on the experiment results, the database was established for the identification of coal-rock interfaces in coal mining machines. The terahertz detection was performed on 10 different kinds of sheet anthracite with different thickness, and the terahertz spectra of coal seams with different thickness were simulated and calculated by using simulation software, which can accurately obtain the thickness of coal seams and provide effective mining thickness parameters for coal seam mining. Through the experiment and simulation, the terahertz time-domain spectroscopy technology has a promising application prospect in the identification of coal-rock interface.

This study focuses on the formulation and analysis of a numerical method to compute singularly perturbed functional differential equations (SP-FDEs) involving large mixed shifts. SP-FDEs are a class of differential equations with both shifts and small perturbation parameter. Such equations arise in various scientific fields to model phenomena with memory effects and perturbed dynamics. In this particular study, the considered SP-FDEs involve large negative shift (delay) and large positive shift (advance). Dealing with large mixed shifts in SP-FDEs gives rise to challenges in terms of stability analysis, numerical methods, and convergence of a solution. In this paper, the influence of the large mixed shifts is treated by choosing a uniform mesh discretized in such a way that the term with the shifts lie on the nodal points. Then, using the Numerov’s finite difference method, the continuous problem is transformed into a finite difference scheme and the influence of the perturbation parameter is handled by introducing a fitting factor in the difference scheme. Stability estimate and convergence analysis of the developed scheme are investigated and proved. Numerical experiments are carried out to demonstrate the validity and applicability of the developed scheme. It is shown that the numerical scheme obtained in this work is parameter-robust of second order convergence rate.

Both auditory and vestibular primary afferent neurons can be activated by sound and vibration. This review relates differences between them to the different receptor/synaptic mechanisms of the two systems as shown by indicators of peripheral function – cochlear and vestibular compound action potentials (cCAPs and vCAPs) to click stimulation as recorded in animal studies. Sound and vibration sensitive type 1 receptors at the striola of the utricular macula are enveloped by the unique calyx afferent ending which has three modes of synaptic transmission. Glutamate is the transmitter for both cochlear and vestibular primary afferents, however blocking glutamate transmission has very little effect on vCAPs but greatly reduces cCAPs. We suggest that the ultrafast non-quantal synaptic mechanism called resistive coupling is the cause of the short latency vestibular afferent responses and related results – failure of transmitter blockade, masking, and temporal precision. This “ultrafast” non-quantal transmission is effectively electrical coupling dependent on the membrane potentials of the calyx and the type 1 receptor. The major clinical implication is that decreasing stimulus rise-time increases vCAP response, corresponding to the increased VEMP response in human subjects . Short rise-times are optimum in human clinical VEMP testing, whereas long rise-times are mandatory for audiometric threshold testing.

Intercalation of noble metals can produce giant Rashba-type spin-orbit splittings in graphene. The spin-orbit splitting more than 100 meV has not yet been achieved in graphene on a metallic or a semiconductor substrate. Here, we report the p-type graphene obtained by Pt intercalation of zero-layer graphene on SiC substrate. The spin splitting of ∼200 meV was observed at a wide range of binding energies. Comparing the results of theoretical studies of different models with the experimantal ones measured by spin-ARPES, XPS and STM methods, we came to the conclusion that inducing giant spin-orbit splitting requires not only a fairly close arrangement of graphene to Pt layer, but also the presence of graphene corrugation caused by non-flat Pt layer. This makes it possible to find a compromise between strong hybridization and increased spin-orbit interaction. In our case, this is achieved by forming Pt submonolayer ordered on a nanometer scale under graphene.

The type III receptor tyrosine kinase FLT3 is a pivotal kinase for hematopoietic progenitor cell regulation, with significant implications in acute myeloid leukemia (AML) through mutations like internal tandem duplication (ITD). This study delves into the structural intricacies of FLT3, the roles of activation loop mutants, and their interaction with tyrosine kinase inhibitors. Coupled with this, the research leverages molecular contrastive learning and protein language modeling to examine interactions between small molecule inhibitors and FLT3 activation loop mutants. Utilizing the ConPLex platform, over 5.7 million unique FLT3 activation loop mutants-small molecule pairs were analyzed. The binding free energies of three inhibitors were assessed, and cellular apoptotic responses were evaluated under drug treatments. Notably, the introduction of the Xepto50 scoring system provides a nuanced metric for drug efficacy. The findings underscore the modulation of molecular interactions and cellular responses by Y842 mutations in FLT3-KD, highlighting the need for tailored therapeutic approaches in FLT3-ITD-related malignancies.

It has been recently demonstrated that inelastic helium-atom scattering from conducting surfaces can provide a direct measurement of the surface electron-phonon coupling constant (mass-enhancement factor ) via the temperature- or the incident-energy-dependence of the Debye-Waller exponent. The analysis of previous published as well as unpublished helium atom scattering diffraction data from the vicinal surfaces of copper (Cu(11),  = 3,5,7) and aluminium (Al(221) and Al(332)) permits to extract  for this class of surfaces, suggesting an enhancement with respect to the corresponding data for the low-index surfaces (111) and (001) above a possible roughening transition temperature. The specific role of steps as compared to that of terraces is briefly discussed.

Taking Korla fragrant pear as the research object, single factor testing and water and fertilizer coupling testing were conducted. Under the premise of the drip irrigation mode, the effects of water, nitrogen, and phosphorus on the growth, fruit quality, and yield of Korla Fragrant Pear were studied to provide a theoretical basis for efficient water and fertilizer management. Among them, the single factor test set water, nitrogen and phosphorus as the three factors, and each factor was set at five levels, namely, water (W1, 5460 m3·hm−2;W2, 5880 m3·hm−2;W3,6300 m3·hm−2; W4, 6720 m3·hm−2; W5, 7140 m3·hm−2), nitrogen (N1, 150 kg N·hm−2;N2, 225 kg N·hm−2; N3, 300 kg N·hm−2; N4, 375 kg N·hm−2; N5, 450 kg N·hm−2), phosphorus (P1,75 kg P2O5·hm−2; P2, 150 kg P2O5·hm−2; P3, 225 kg P2O5·hm−2; P4, 300 kg P2O5·hm−2; P5, 375 kg P2O5·hm−2). The results showed that the total nitrogen and total phosphorus contents in leaves under the W3, W4, N3, N4, P3, and P4 treatments were significantly higher than those under other treatments, and the fruit quality was better. Therefore, the W3, W4, N3, N4, P3, and P4 treatments were selected as the water and fertilizer inputs for the water–fertilizer coupling test for Korla fragrant pear. Eight treatments were set up in the water and fertilizer coupling test: Treatment 1 (T1, W3N3P3), Treatment 2 (T2, W3N3P4), Treatment 3 (T3, W3N4P3), Treatment 4 (T4,W3N4P4), Treatment 5 (T5, W4N3P3), Treatment 6 (T6, W4N3P4), Treatment 7 (T7, W4N4) P3), and Treatment 8 (T8, W4N4P4). The results showed that the leaf area index of the T1, T2, T3, and T4 treatments was significantly higher than that of the other treatments at maturity. The T3 treatment resulted in the highest fruit yield, single fruit weight, and primary fruit rate. The results of the grey correlation degree analysis of fruit quality showed that T3 treatment had the highest degree of correlation and ranking of each fruit quality index, indicating that T3 treatment had the highest fruit quality. Detailed investigation of pear tree growth and fruit quality showed that the T3 treatment (375 kg·hm−2 nitrogen application, 225 kg·hm−2 phosphorus application and 6300 m3·hm−2 irrigation) had the best fruit growth and development performance, and the sweet pear fruit quality was the best.

The electrical motor design requires a lot of work and resources. In the field, motor designers need to decide on competitive motor sizing quickly to compete with other motor suppliers. Generally, it requires expensive FEM S/W to get accurate motor sizing results, but buying and maintaining many licenses is costly. Moreover, it needs some patience to get the result from FEM analysis. In this paper, the motor sizing technique using an existing production motor is presented to respond to urgent requests from customers without using FEM analysis. In order to enhance the fidelity of the result, magnetic flux loss by magnet coating and non-linear characteristics are considered during the motor sizing process. The proposed sizing method was verified by comparison to the FEM analysis and test result and showed reasonable confidence in them. Also, this method has the substantial advantage of outputting accurate results instantly without taking any time. It helps with the modification design of electrical motors without using expensive FEM S/W and a certain level of skill or experience.

The dynamics of hydrological lateral nutrient fluxes contribute to our understanding of ecological functions related to energy, materials, and organism flows across various spatiotemporal scales. To explore the connectivity between multiple spatial flow processes, we conducted a one-year field measurement to assess lateral hydrologic carbon (C) and nitrogen (N) fluxes over the continental shelf in the Yangtze estuary. We observed a significant correlation between the differences in remote sensing-based estimates of gross primary production (GPP) (∆GPPMODIS) and the differences in eddy covariance (EC) tower-based GPP (∆GPPEC) at both high-elevation and low-elevation sites. Over the course of a year, our predicted daily maximum tidal elevation (TE) closely matched the observed values in the creek, which facilitated the development of theoretical models to simulate biogeochemical cycling processes and aquatic ecosystem functions. Our findings indicate that the studied saltmarsh acts as a net exporter of dissolved total C (DTC) while serving as a net sink for dissolved total N (DTN). Furthermore, there is a significant correlation in the total dissolved stoichiometry of the C/N ratio between imports and exports. These findings highlight the importance of integrating ecological stoichiometric principles to gain a deeper understanding of the complex relationships between physical, chemical, and biological processes, particularly within the context of the meta-ecosystem framework. Additionally, when considering reciprocal hydrological lateral C and N flows, single ecosystem can function both as sources and sinks within the meta-ecosystem framework.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

U-Net, based on a deep convolutional neural network (CNN), has been clinically used to au-to-segment normal organs and potentially target volumes. However, CNNs with local geometric dependencies may limit the accuracy of segmentation. Additionally, the performance of CNNs can vary depending on the selection of network hyper-parameters, which was mitigated by the proposition of nnU-Net. We chose a vision transformer architecture called VT U-Net, which features a self-attention excluding the convolution layer, to overcome the limitations of CNNs by utilizing global geometric information of images. The VT U-Net v.2 became more powerful thanks to the adaptive hyper-parameter optimizer embedded in nnU-Net. However, despite leveraging the benefits of nnU-Net, VT U-Net v.2 still had additional network hyper-parameters that needed to be optimally chosen. Accordingly, among various hyper-parameters, this study attempted to find the optimal combination of the patch size and the embedded dimension regarding the transformer. From the 4-fold cross-validation, the modified VT U-Net v.2 showed the highest average performance for planning target volume (PTV) segmentation among the investigated networks. Though nnU-Net was based on convolution layers, the adaptive hyper-parameter optimizers turned out to enhance the performance. It was also confirmed that network hyper-parameters affected the segmentation accuracy of vision transformers.

In this paper we will provide a new equation that explains why there are three generations or families of leptons and quarks, respectively. We will also explain why all those particles have the known mass ratios amongst their three respective generations and flavors. We will also tackle the problem of Yukawa couplings being arbitrary parameters in the Standard Model Higgs mechanism, which is a long standing problem do to their formulaic dependence on the Higgs Vacuum Expectation Value (VEV). We will attempt to solve this problem and provide a strong argument through an equation for Yukawa couplings of all leptons and quarks via a new methodology that depends on the running of the fine-structure constant on the Q scale, quantum numbers and the Weinberg angle (also on the Q scale). We will also make predictions for all three left-chiral neutrino mass eigenstates and we will provide upper limits for the three right-chiral neutrino mass eigenstates

Alzheimer’s disease (AD) and vascular dementia (VaD) together contribute to almost 90% of all dementia cases leading to major health challenges of our time with a substantial global socioeconomic burden. While in Alzheimer’s disease, the improved understanding of Amyloid beta (Aß) mismetabolism and tau hyperphosphorylation as pathophysiological hallmarks has led to significant clinical breakthroughs, similar advances in VaD are lacking. We thus highlight here the importance of shared pathomechanisms found in AD and VaD: Endothelial damage, blood brain barrier (BBB) breakdown and hypoperfusion inducing oxidative stress, inflammation and demyelination and thus trophic uncoupling in the neurovascular unit. A dysfunctional endothelium and BBB lead to the accumulation of neurotoxic molecules and Aß through impaired clearance, which in turn leads to neurodegeneration. In this context we discuss possible neuropathological parameters, which might serve as biomarkers and thus improve diagnostic accuracy or reveal targets for novel therapeutic strategies for both forms of dementia.

The main advantage of using the ferroelectric material as a component of complex heterostructure is the ability to tune various properties of the whole system by means of external electric field. In particular, the electric field may change the polarization direction within the ferroelectric material and consequently affect the structural properties, which in turn affects the electronic and magnetic properties of the neighboring material. Besides, the ferroelectrics proceed the electrostriction phenomenon, which is promising to be used to affect the magnetic states of interface state in the heterostructure with a magnetic component. The interfacial phenomena are of a great interest since they provide an extended functionality useful for electronic devices of a new generation. Following an idea of utilizing a ferroelectric in heterostructures component in the present work we consider 2DEG, Rashba effect, the effect of magnetoelectric coupling and magnetostriction in order to emphasize the advantages of such heterostructures as components of devices. For this purpose model systems of LaMnO3/BaTiO3, La2CuO4/BaTiO3, Bi/BaTiO3 and Bi/PbTiO3, Fe/BaTiO3 heterostructures are investigated by density functional theory calculations.

RANS simulations have been broadly used to investigate turbulence in the oceans and atmosphere. Within these environments there are a multitude of tracers undergoing reactions (eg. phytoplankton growth, chemical reactions). The distribution of these reactive tracers is strongly influenced by turbulent mixing. With a 50 member ensemble of two dimensional Rayleigh-Taylor induced turbulent mixing, we show that the dynamics of a reactive tracer growing according to Fisher’s equation are poorly captured by the mean. A fluctuation-dependent sink introduced by Reynolds averaging Fisher’s equation transfers concentration from the mean to the fluctuations. We compare the dynamics of the reactive tracer with those of a passive tracer. The reaction causes the concentration of reactive tracer to increase thereby increasing Fickian diffusion and allowing the reactive tracer to diffuse into turbulent structures that the passive tracer cannot reach. A positive feedback between turbulent mixing and fluctuation growth is identified. We show that eddy viscosity and diffusivity parameterizations fail to capture the bulk trends of the system and identify a need for negative eddy diffusivities. One must therefore be cautious when interpreting RANS results for reactive tracers.

Upcycling recycled carbon fibers recovered from waste carbon composites can reduce the price of carbon fibers while improving disposal-related environmental problems. This study assessed and characterized recycled carbon fibers subjected to sizing treatment using N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (APS) chemically coordinated with polyamide 6 (PA6) and polypropylene (PP) resins. Sizing treatment with 1 wt.% APS for 10 s yielded O=C-O on the surface of the carbon fiber, and the -SiOH in the APS underwent a dehydration-condensation reaction that converted O=C-O (lactone groups) into bonds of C-O (hydroxyl groups) and C=O (carbonyl groups). The effects of C-O and C=O on the interfacial bonding force increased to a maximum, resulting in an oxygen-to-carbon ratio (O/C) of 0.26. The polar/surface energy ratio showed the highest value of 32.29% at 10 s, and the interfacial bonding force showed the maximum value of 32 MPa at 10 s, which is about 15% better than that of commercial carbon fiber (PA6-based condition). In 10-s resizing treatments with 0.5 wt.% 3-methacryloxypropyltrimethoxysilane (MPS), C-O, C=O, and O=C-O underwent a dehydration-condensation reaction with -SiOH, which broke the bonds between carbon and oxygen and introduced a methacrylate group (H2C=C(CH3)CO2H), resulting in a significant increase in C-O and C=O, with an O/C of 0.51. The polar/surface free energy ratio was about 38% at 10 s, with the interfacial bonding force increasing to 27% compared to commercial carbon fiber (PP-based conditions). The MPS exhibited a superior interfacial shear strength improvement, two times higher than that of APS, with excellent coordination with PP resin and commercial carbon fiber, although the interfacial bonding strength of the PP resin was significantly lower.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

The flour milling industry, a vital component of global food production, is undergoing a transformative phase driven by the integration of smart devices and advanced technologies. This transition promises improved efficiency, quality, and sustainability in flour production. Accurate estimation of protein, moisture and ash content in wheat grains and flour is of paramount importance due to their direct impact on product quality and compliance with industry standards. This paper explores the application of Near-Infrared (NIR) spectroscopy as a non-destructive, efficient, and cost-effective method for measuring the aforementioned essential parameters in wheat and flour, by investigating the effectiveness of a low-cost handle NIR spectrometer. Furthermore, a novel approach using Fuzzy Cognitive Maps (FCMs) is proposed to estimate protein, moisture and ash content in grain seeds and flour, marking the first known application of FCMs in this context. Our study includes an experimental setup that assesses different types of wheat seeds and flour samples and evaluates three NIR pre-processing techniques to enhance parameter estimation accuracy. The results indicate that low-cost NIR equipment can contribute to the estimation of the under-study parameters.

This investigation delves into the profound interplay between the e-commerce environment and the agricultural system, while scrutinizing the intricate human-land coupling dynamics engen-dered by transformations within the agricultural domain. Focusing on the expansion of orchards in Pinghe County, a pivotal epicenter for Chinese sweet pomelo production, this study eluci-dates the reverberations of Rural E-commerce Environment Development on Orchard Expansion through the lens of Tele-coupling. In doing so, it unveils the nuanced tapestry of the human-land coupling associations latent within the evolutionary trajectory of the agricultural system amidst the blossoming information society. The findings underscore a symbiotic relationship between the augmentation of orchard acreage and the burgeoning rural e-commerce landscape, effec-tively propelling the economic prosperity of the agricultural system. Moreover, a tele-coupling phenomenon has emerged, underscoring the intricate web of interconnections binding the mat-uration of the rural e-commerce ecosystem with the proliferation of orchards. The research illu-minates that the transformation of land utilization, imbricated within the agricultural system, manifests as a distinctive form of tele-coupling intricately woven into the fabric of urbanization and information technology advancements. Consequently, adopting a comprehensive theoreti-cal perspective, amalgamating disparate domains across distinct geographic realms, becomes imperative for discerning the intricate nuances of the human-land coupling nexus within these multifaceted, open systems.

Integrating systems acquired from third parties and legacies has become of great necessity in companies. This is mainly due to the need to exchange information between entities, such as banks, suppliers, customers, allies, etc. Therefore, it is essential to guarantee the integrity of the data and keep the integration up to date with the changes that can occur. Furthermore, reducing the transaction risk and avoiding losing information is necessary. Implementing this complex task involving technological and business challenges requires appropriate architecture implementation. This article presents an architecture named Dynamic Canonical Data Model through agnostic messages. The contribution involves treating the low link in integrating software units, also called the integration of loosely coupled software units. In particular, it focuses on internal data and external data integration. The proposal reduces their integration, maintenance time, and cost, maximizing their scalability and promoting reuse. To illustrate their components, a case study undertaken at the Mexican Logistics Company Paquetexpress is presented. The company has evaluated different enterprise application integration systems over 26 years to achieve a standardized integration. The article describes an architecture designed and implemented for this delivery company in a real-world case. The implementation’s source code was registered in the National Registry of Copyrights of Mexico.

A recent study demonstrated that noninvasive measurements of cortical hemodynamics and metabolism in the resting human prefrontal cortex can facilitate quantitative metrics of unilateral mitochondrial-hemodynamic coupling and bilateral connectivity in infraslow oscillation (ISO) frequencies in young adults (YA). The ISO includes three distinct vasomotions with endogenic (E), neurogenic (N), and myogenic (M) frequency bands. The goal of this study was to prove the hypothesis that there are significant differences between young and older adults (OA) in the unilateral coupling (uCOP) and bilateral connectivity (bCON) in the prefrontal cortex. Accordingly, we performed measurements from 24 OA (67.2 ± 5.9 years of age) using the same 2-channel broadband near-infrared spectroscopy (bbNIRS) setup and resting-state experimental protocol as those in the recent study (Shahdadian et al, Cerebral Cortex Communications, 2022). After quantification of uCOP and bCON in three E/N/M frequencies and statistical analysis, we demonstrated that OA had significantly weaker bilateral hemodynamic connectivity but significantly stronger bilateral metabolic connectivity than YA in the M band. Furthermore, OA exhibited significantly stronger unilateral coupling on both prefrontal sides in all E/N/M bands, particularly with a very large effect size in the M band (&gt; 1.9). These age-related results clearly support our hypothesis and were well interpreted following neurophysiological principles. The key finding of this paper is that the neurophysiological metrics of uCOP and bCON are highly associated with age and may have the potential to become meaningful features for human brain health and be translatable for future clinical applications, such as early detection of Alzheimer’s disease.

Complexes of triply positive europium ion with organic ligands are popular objects for studying photophysical properties. This is related not only to the bright red emission of this 4f element, but also to some spectroscopic peculiarities of its luminescence: the first excited spin-orbit level (7F1) lies only about 300 cm−1 above the ground state (7F0), so that at room temperature its population is around 25–30%. However, such electronic structure of Eu(III) provides its paramagnetism under ordinary conditions. This fact is often ignored by researchers, which is shortsighted from the materials science point of view. A comprehensive and systematic study of the magnetic behavior for the Eu(III) molecular coordination compounds is a challenging task for the development of new polyfunctional materials. The present work presents synthesis, single crystal XRD analysis results, and a magnetic study for the firstly prepared europium(III) complexes with two neutral scorpionate ligands: trispyrazolylmethane (HCPz3) and its methylated analog, tris(3,5-dimethyl-1-pyrazolyl)methane (HC(PzMe2)3). The values of the spin-orbit coupling parameter obtained for Eu-trication by a theoretical approximation of the experimental magnetic susceptibility data are compared with those known for the scarce amount of the magnetically studied molecular compounds.