The boundary layer height (BLH) distinguishes the interface between the lower and free atmosphere, which is a key variable in numerical simulation, aerosol, and environmental pollution studies. Thus, the goal of this work is to propose a novel method conjuncting with numerical regularization to analyze climate characteristics of the marine boundary layer height (MBLH) using 2007-2011 GPS-RO data from the COSMIC mission. While traditionally, the difference method has been used to achieve this aim, herein, we propose an innovative method, in which the bending angle profile gradient was calculated using the numerical regulation method where the regulation parameters are determined by the double-parameter model function method. Then, the MBLH was determined by employing the maximum gradient method to ascertain the height corresponding to the smallest gradient. The results show a correlation between currents and the MBLH—a relationship that has not been previously demonstrated. A low MBLH is associated with seasons and regions where cold ocean currents are prevailing; whereas a high MBLH is observed in the seasons and places where warm currents are prevailing. This correlation was validated by comparing the obtained results with different occultation data—i.e., atmprf and echprf—which also established that atmprf is more sensitive to convective cloud top capture. In seas with active convection, the armprf calculated bending angle is higher than that from echprf. Subsequently, the standard deviation was used to express the MBLH confidence level. The results show that the MBLH standard deviation is highest in low latitudes and lowest in the middle and high latitudes. Furthermore, we analyzed the interannual MBLH variation trend, which displayed a seasonal variation and spatial distribution corresponding with the current and subsolar point. Finally, we conducted a case study in the South China Sea, and identified a distinctive seasonal change and downward trend.

Remotely sensed data play a crucial role in monitoring the El-Niño/La-Niña Southern Oscillation (ENSO), which is an oceanic-atmospheric phenomenon occurring quasi-periodically with several impacts worldwide, such as specific biological and global climate responses. Since 1980, Earth has witnessed three strong ENSO events (1982–1983, This study aims, 2015-2016). In September 2022, La-Niña entered its third year and was unlikely to continue through 2023. Instead, since 2022 forecasts pointed to a transition from La-Nina to a Neutral phase in summer or late 2023. The onset of the El-Niño occurred around April 2023, and it is anticipated by sophisticated models to be a strong event through the Northern Hemisphere winter (December 2023 - February 2024). The aim of this study is to demonstrate the ability of the combination of two new methods to improve the accuracy of the above claim because El-Niño apart from climate anomalies, significantly impacts Earth’s ecosystems and human societies, regulating the spread of diseases by insects (e.g., malaria and dengue fever), and influencing nutrients, phytoplankton biomass, and primary productivity. This is done by exploring first the previous major El-Niño events in the period January 1876-July 2023. Our calculations show that the ongoing 2023-2024 El-Niño will not be the strongest.

Marek’s disease (MD) is an important neoplastic disease caused by serotype 1 Marek's disease virus (MDV-1), which results in severe economic losses worldwide. Despite vaccination practices that have controlled the MD epidemic, current increasing MD-suspected cases indicate the persistent viral infections circulating among vaccinated chicken farms in many countries. However, the lack of available information about phylogeny and molecular characterization of circulating MDV-1 field strains in Taiwan reveals a potential risk in MD outbreaks. This study investigated the genetic characteristics of 18 MDV-1 isolates obtained from 17 vaccinated chicken flocks in Taiwan between 2018 and 2020. Based on the sequences of the meq oncogene, phylogenetic analysis demonstrated that the circulating Taiwanese MDV-1 field strains were predominantly in a single cluster that showed high similarity with strains/isolates from countries of East Asian region. Because the isolated strains were obtained from CVI988/Rispens vaccinated chicken flocks and the molecular characteristics of the Meq oncoprotein showed the features like vvMDV and vv+MDV strains, the circulating Taiwanese MDV-1 field strains may have higher virulence compared with vvMDV pathotype. In conclusion, the presented data demonstrate the circulation of hypervirulent MDV-1 strains in Taiwan and highlight the importance of routine surveillance and precaution strategies in response to the emergence of enhanced virulent MDV-1.

Evaluating genetic diversity in walnut (Juglans regia L.) populations is a rapid approach used by walnut breeding programs to distinguish superior genotypes. The present study identified the Hamedan province walnut population as one of the richest, most genetically diverse regions in Iran during 2019-2020. After initial screening, 47 genotypes were selected for further evaluation of pomological and phenological traits based on International Plant Genetic Resources Institute (IPGRI) descriptors. Nut and kernel weights among the selected genotypes ranged between 7.15-21.05 g and 3.0-10.8 g, respectively. Principal component analysis (PCA) categorized genotypes into three distinct groups while cluster analysis (CA) further categorized genotypes into one of four groups. Spearman correlation analysis showed a positive correlation (P <0.01) between nut weight (NWT), nut size, and kernel weight (KW) while a negative correlation (P <0.01) between shell thickness (STH) and packing tissue thickness (PTT) with kernel percentage (KP) was observed. Lastly, 10 of 47 genotypes (TAL8, TAL9, TAL10, TAL14, TAL19, TAL22, TB2, TB4, TB6, and RDGH5) were considered superior. Superior genotypes were late-leafing (25-40 days after the standard) and displayed a lateral bearing (LB) habit with heavy nuts (12.52–16.82 g) and kernels (6.53–8.15 g), thin-shells (1.06–1.25 mm), and lightly-colored kernels. Cuttings of superior genotypes were then grafted in the orchard. Detecting superior and late-leafing genotypes in this investigation suggests cultivars resistant to late-spring frost may soon be isolated.

Abstract. Indonesia has developed several superior soybean varieties. Each soybean variety has different physical and chemical properties that can affect processed products and soybean quality. The purpose of this study was to determine the physical, chemical, and functional properties of three superior early-maturing soybean varieties. The research was conducted in Maros, Indonesia in 2022 by planting the Dega-1, Grobogan, and Gepak Kuning varieties and repeated them 6 times. The yields of the three soybean varieties Dega-1, Grobogan, and Gepak Kuning were taken at 1 kg each and 3 repeated, then further analysis of chemical compounds is carried out in the laboratory. The results showed that for physical characteristics, the largest seed size was in Dega-1 (18.57 g per 100 seeds) and the smallest in Gepak Kuning (8.29 g). The highest bulk density of soybean seeds was in the Grobogan and Dega-1 varieties (0.79 kg per m3) and the lowest was in Gepak Kuning (0.77 kg per m3 ), and the lowest number of damaged seeds was in Dega-1 (6.67%) and the highest in Grobogan (11.33). %). Chemical characteristics, highest protein content in Gepak Kuning (39.72%) and lowest in Dega-1 (36.62%), lowest fat content in Dega-1 (12.63%) and highest in Gepak Kuning (14.49%), highest phosphorus content in Gepak Kuning (0.59%) and the lowest was in Grobogan (0.53%), the highest calcium content was in Gepak Kuning (0.40%), and the highest FFA value was in Dega-1 (0.93) and the lowest in Gepak Kuning (0.81). Based on physical properties, Dega-1 is the best compared to the other two soybeans. Meanwhile, based on the size of starch granules, Gepak Kuning gave the best results. For chemical characteristics, in general, GepakKuning has the best quality compared to Grobogan and Dega-1. It can be concluded that Gepak Kuning has the most potential to be developed in supporting food and non-food products, especially in Indonesia.

The objective of this research is to conduct a comparative analysis between rectangular-shaped ASTM D3039 specimens with different angles (0°, 15°, and 90°) and various tensile test specimens based on ASTM and ISO standards, all 3D-printed using polyethylene terephthalate glycol (PETG) material through FDM. The study aimed to assesses the weak spot commonly found at the neck of the specimens. Two different printing orientations, namely flat and on-edge, were investigated, and a comprehensive examination and comparison were made regarding the variations in tensile strength, E-modulus, strain, and elongation at break among the tested samples. Additionally, the broken areas was evaluated, and a numerical study utilizing the finite element method (FEM) was conducted to identify stress risers' locations in each specimen type. The experimental results demonstrated that the ASTM D3039-0° specimen exhibited the best tensile properties when printed in the on-edge orientation, while the flat orientation yielded the best results in terms of the broken area. On the other hand, the ISO 527-2 specimens displayed the lowest tensile properties, regardless of the printing orientation. The study highlighted the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location.

Background Frequent presenters (FPs) define a group of individual who visit hospital emergency depart-ment (ED) frequently for urgent care. Many among the group present with main diagnosis of mental health conditions. This group of individual tend to use ED resources disproportionally and significantly affect overall healthcare outcome. No previous reviews have examined the profiles of FPs with mental health conditions. Aims This study aims to identify the key socio-demographic and clinical characteristics of patients who frequently present to ED with mental health primary diagnosis by performing systemic review from existing literature. Method PRISMA guideline was used. PubMed, PsycINFO, Scopus and Web of Science (WOS) were searched in May 2023. A manual search on reference list of included articles were conducted at same time. Covidence was used to perform extraction and screening, completed by two authors independently. Inclusion and exclusion criteria were defined. Results The abstracts of 3341 non-duplicate articles were screened with 40 full texts assessed for eligi-bility. 20 studies were included from 2004-2022 conducted in 6 countries with total patient number of 25688 (52% male, 48% female, mean age 40.7 years old). 27% were unemployed, 20% married, 41% homeless, and 17% had tertiary or above education. 44% had history of substance abuse or alcohol dependence. Top 3 diagnosis are found to be anxiety disorders (44%), depressive disorders (39%) and schizophrenia spectrum and other psychotic disorders (33%). Conclusion On average, FPs are middle aged and equally prevalent in both gender. Current data lacks rep-resentation for gender diverse group. They are significantly associated with high rate of unem-ployment, homelessness, lower than average education level, and being single. Anxiety disor-der, depressive disorder, and schizophrenia spectrum disorders are the most common clinical diagnosis associated with the group.

Alginate extraction is from seaweed, and lignin separation is from by-product corn (stalks and leaves). Alginate/lignin is a synthetic polymer rich in biological activity of great interest. Antioxidant activities of alginate/lignin were evaluated, such as total antioxidant activity, reducing power activity, DPPH free radical scavenging activity, and α – glucosidase inhibition activity. The test of anticancer activity was on four cell lines (Hep G2, fibroblast, MCF-7, and NCI H460). Determination of physical-chemistry characteristics of alginate/lignin was through FTIR, DSC, SEM_EDS, SEM_EDS mapping, XRD, XRF, and 1H-NMR. A study of acute toxicity of alginate/lignin was on Swiss albino mice. The results showed alginate/lignin possessed antioxidant activity such as total antioxidant activity, reducing power activity, especially, α – glucosidase inhibition activity, and no free radical scavenging activity. Alginate/lignin did not be typical in cancer cell lines. Alginate/lignin existed in a thermally stable regular spherical shape in the investigated thermal region. Some specific functional groups of alginate and lignin did not exist in alginate/lignin crystal. Elements such as C, O, Na, and S were popular in the alginate/lignin structure. LD0 and LD100 of alginate/lignin in mice were 3.91 g/kg and 9.77 g/kg, respectively. Alginate/lignin is the potential for application as pharmaceutical materials, functional foods, and supporting diabetes treatment.

The opinion dynamics literature argues that the way people perceive social influence depends not only on the opinions of interacting individuals, but also on the individuals’ non-opinion characteristics, such as age, education, gender, or place of residence. The current paper advances this line of research by studying longitudinal data that describe the opinion dynamics of a large sample (~30,000) of online social network users, all citizens of one city. Using these data, we systematically investigate the effects of users’ demographic (age, gender) and structural (degree centrality, the number of common friends) properties on opinion formation processes. We revealed that females are less easily influenced than males. Next, we found that individuals that are characterized by similar ages have more chances to reach a consensus. Besides, we report that individuals who have many common peers find an agreement more often. We also demonstrated that the impacts of these effects are virtually the same, and despite being statistically significant, are far less strong than that of opinion-related features: knowing the current opinion of an individual and, what is even more important, the distance in opinions between this individual and the person that attempts to influence the individual is much more valuable. Next, after conducting a series of simulations with an agent-based model, we revealed that accounting for non-opinion characteristics may lead to not very sound but statistically significant changes in the macroscopic predictions of the populations of opinion camps, primarily among the agents with radical opinions (≈ 3% of all votes). In turn, predictions for the populations of neutral individuals are virtually the same. Besides, we demonstrated that the accumulative effect of non-opinion features on opinion dynamics is seriously moderated by whether the underlying social network correlates with the agents’ characteristics. After applying the procedure of random shuffling (in which the agents and their characteristics were randomly scattered over the network), the macroscopic predictions have changed by ≈ 9% of all votes. What is interesting, the population of neutral agents was again not affected by this intervention.

Irrational belief is a product of complex personality traits and Machiavellianism Intelligence. The present study is conducted to trace the significance of predictive nature of personality characteristics and Machiavellianism Intelligence (Mach Intelligence) on irrational beliefs among chronically ill older people. The research method is cross-sectional with correlational design, purposive sampling with a total of 200 chronically ill older people aged between 40–60 years with disease type such as Systemic lupus erythematosus, Complicated Diabetes, Glomerulonephritis and Chronic Heart Failure. The analysis revealed that personality characteristics and irrational belief subscales such as worrying, rigidity, problem avoidance and Mach Intelligence are significantly positively correlated; however, Emotional irresponsibility has significant negative correlation with personality characteristics and Mach Intelligence. Gender differences revealed that males are high on all the subscales of personality characteristics, irrational beliefs (except emotional irresponsibility) and Mach Intelligence as com-pared to female chronically ill older people. Predictive analysis also revealed that overall personality characteristics explained a total of 67% variance in irrational beliefs. Moreover, Mach Intelligence predicts irrational beliefs. Future health related recommendations should be planned accordingly.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

RNA interference (RNAi) is one of the main mechanisms for disease resistance and small RNA production in plants. The main proteins involved in RNAi include Dicer-like (DCL), RNA-dependent RNA polymerase (RDR), double-stranded RNA-binding (DRB), and Argonaute (AGO). Juglandaceae contains a variety of important woody plants, and walnuts are one of the four major woody plant groups and one of the four major dried fruits in the world. To clarify the evolution and functional differentiation of RNAi-related proteins in the walnut (Juglans regia) genome, this study integrated various web resources from gene family acquisition to structural analysis and transcriptome data to correlate walnuts and their congeners. The walnut genome has 5 DCL, 13 RDR, 15 DRB and 15 AGO genes, similar genes encoding conserved protein structural domains and conserved motifs with similar subcellular localization. Walnut AGO proteins are classified into three classes and seven subclasses. The DCL is divided into four categories, while RDR is mainly divided into four categories, and DRB can be divided into six categories. The exception is that the copy number of walnut RDR1 is 9, in which seven RDR1 are distributed in clusters on chromosome 16. Purifying selection drove the formation of walnut genes, but protein classes were subjected to varying degrees of purifying selection. Additionally, these results showed some similarity in other plants of the walnut family. Moreover, different RNAi-related genes of walnut produced abundant selective expression in response to different tissues and stresses. In this study, DCL, RDR, DRB and AGO gene families were identified and analysed in the genome of the walnut family for the first time and preliminarily examined the evolution, structure and expression characteristics of these families to provide a preliminary basis for the evolution of the walnut RNAi pathway and breeding research.

What would compel a composer to set the same poem twice? Ludwig van Beethoven first set the text of Christoph Tiedge’s “An Die Hoffnung” (to Hope) between 1804 and 1805, and would later set the poem again, using even more of the text in 1815. While seeking context clues from what is known of his biography is crucial, another avenue of study lies within the pieces themselves. Through the study of key characteristics during Beethoven’s lifetime in addition to what biographical information we know, we can infer Beethoven’s intentions with each setting of the text and how this reflects his changing relationship to the text of “An Die Hoffnung”.

The worldwide competition to vaccinate against COVID-19 has highlighted the importance of immunization measures in containing the virus. Saudi Arabia, like the rest of the globe, must assess socio-demographic subtleties, chronic illnesses, vaccination effects, and public health policy implications as it navigates this complicated environment. This cross-sectional study examined Saudi COVID-19 vaccine in many ways. It examined the socio-demographic makeup of vaccine recipients, the prevalence of chronic conditions in this population, vaccine administration patterns, post-vaccination side effects, and vaccine-infection rates. A questionnaire-based online survey of 401 participants ensured gender, nationality, age, weight, and educational diversity. We analyzed vaccine manufacturer choice for each dosage, side effects after the first and second doses, and chronic diseases in the sample. Pfizer/BioNTech vaccines are preferred for all three doses, reflecting worldwide vaccination acceptance patterns. Side effects were not significantly different between vaccination kinds. Interestingly, immunization reduced infection rates, demonstrating the efficacy of COVID-19 vaccines. The data fills important information gaps and illuminates Saudi COVID-19 vaccination kinetics. These data support the global preference for mRNA vaccines, demonstrating the faith in this breakthrough technology. They also sponsor COVID-19 vaccine safety and effectiveness studies. The dramatic drop in infection rates among vaccinated people shows how vaccinations suppress the pandemic. These findings inform Saudi Arabia's immunization efforts. As booster doses become more common, long-term vaccination research is crucial. Vaccine reluctance, especially in certain demographics, must be addressed. Due to vaccines' protective potential, equitable vaccine distribution and large immunization programs are essential for herd immunity and pandemic management. This thorough cross-sectional study helps policymakers and healthcare practitioners build successful and inclusive COVID-19 immunization regimens in Saudi Arabia.

Фундук является одним из самых ценных орехов в мире благодаря своим уникальным органолептическим свойствам и питательным характеристикам. Данная работа была направлена ​​на анализ некоторых физико-химических свойств различных сортов фундука, выращиваемых в Закаталы (Азербайджан), а именно Ата-баба, Эльбари, Топкара, Фирован, Насими, Галиб, Мирзебейли, Тала, Даш финтик, Барли, Азери и Сачагли. В целом результаты показали статистически значимые различия между изучаемыми сортами. Плотность ядер в зависимости от сортов фундука варьировала от 0,71 г/см ³ (азери) до 1,03 г/см ^{3 .}(Сачакли). Очищенные плоды Дашфиндыг в среднем были тяжелее (1,64±0,34 г), а очищенные плоды Насими, Калиб, Мирзебейли и Сачакли в среднем легче (0,8±0,23 г, 0,8±0,31 г, 0,8±0,20 г и 0,80 г). ±0,09 г соответственно.В неочищенном виде самыми тяжелыми были орехи Дашфиндык (3,70±0,34 г), а самыми легкими из всех сортов были орехи Насими и Калиб (2,0±0,48 г и 2,0±0,36 г соответственно). - орехи баба составляют 49 масс./ядро, %, у остальных изученных сортов - 33,3-45,3 мас.%. Орехи насими имеют округлую форму (в экваториальной зоне); талы, ата-баба, фирован и азери - округло-продолговатые; топкара , Барли и Даш финдык – продолговатые; Эльбари, Калиб, Мирзебейли и Сачакли – удлиненные. Фирован, Тала и Топкара имеют более толстую скорлупу. Ата-баба значительно опережает другие сорта по выходу ядер (490 кг/1 т орехов) , На втором месте по этому показателю находится Тала (453 кг/1 тонна орехов), на третьем – Топкара (433 кг/1 тонна орехов). По максимальной жирности выделены сорта Мирзебейли (77,00±2,20 г/100 г ядер) и Фирован (75,0±3,08 г/100 ядер), по белку - Сачакли (16,02±0,50 г/100 ядер) и Ата-баба ( выделено 15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора.

A scientific carbon accounting system can help enterprises reduce carbon emissions. This study took the enterprise in the Yangtze River basin as a case study. The accounting classification of carbon emissions in the life cycle of lime production was assessed, and the composition of the sources of carbon emission was analyzed, covering mining explosives, fuel (diesel, coal), electricity and high temperature limestone decomposition. Using the IPCC emission factor method, a carbon life cycle emission accounting model for lime production was established. We determined that a total of 354,200 tons of carbon emissions were generated from producing 321,000 tons of lime in a year. The decomposition of limestone at a high temperature was the largest carbon emission source, accounting for 62.34% of the total carbon emission. Coal combustion was also an important source of carbon emissions, accounting for 32.66% of total carbon emissions. The carbon emission for one ton of activated lime was 1.46kg, 1.49kg, 1100kg and 1102.95kg respectively for the open-pit, mining stage, crushing stage, and the calcination stage. Based upon the main sources of carbon emission for lime production, carbon emission reduction should focus on CO2 capture technology, fuel optimization and energy control. Using our analysis of carbon emissions, the carbon emission factor of producing unit quicklime of the lime enterprise in the Yangtze River basin was determined. Furthermore, the research into carbon emission reduction for lime production can provide a point of reference for the promotion of carbon neutrality in the same industry.

Alzheimer's Disease (AD) is a neurodegenerative disease that is common in the elderly. This paper introduces the overview of Alzheimer's disease and the application of relevant signal processing methods in its detection. Signal processing is a technique that converts raw data into meaningful information and is widely used in the medical field. This paper lists common signal processing techniques, including Fourier transform, time-frequency analysis and statistical signal processing, and discusses their applications in the detection of Alzheimer's disease. Fourier transform can convert time domain signals into frequency domain representations, providing an effective tool for the study of EEG in Alzheimer's disease. Time-frequency analysis can perform a combined time and frequency analysis of the signal to help detect the signal characteristics of Alzheimer's disease. Statistical signal processing methods can be used to identify the features of Alzheimer's disease by building mathematical models. Finally, the challenges of Alzheimer's disease detection are discussed, including signal noise, diversity, and insufficient data volume. Through in-depth research and development of signal processing methods, it is expected to improve the accuracy and efficiency of early detection of Alzheimer's disease.

Burn injuries have profound implications for aesthetics, functionality, and patient survival. Umbilical cord lining mesenchymal stem cells (SCL-MSCs) have emerged as a potential therapeutic approach for burn wounds due to their easy isolation, favorable differentiation capabilities, and low immunogenicity. This study aimed to evaluate the growth characteristics of SCL-MSCs and their effectiveness in treating burn wounds. Mechanical isolation was employed to extract mesenchymal stem cells from the umbilical cord lining membrane. The isolated cells underwent characterization, including analysis of HLA-E, G, and DR expression, and assessment of immunogenicity against rabbit antigens using ELISA. A rabbit model was utilized to administer burn treatment. SCL-MSCs exhibited typical morphology of mesenchymal stem cells and demonstrated robust proliferation. These cells expressed CD90, HLA-E, and HLA-G markers while lacking HLA-DR expression. Intact cells and supercrushed cell fluid displayed minimal and unstable immunogenicity. SCL-MSCs exhibited remarkable differentiation potential toward fibroblast lineages, with differentiated fibroblasts showing elevated collagen production and efficient sheet formation. In the experimental rabbit model, burn wounds covered with SCL-MSC tegaderm material plates exhibited superior healing compared to controls. The stem cell material plate area demonstrated reduced inflammatory cell counts (P &lt; 0.01) and increased fibroblast count, neovascularization, and mitotic index (P &lt; 0.01). These findings highlight the potential of SCL-MSCs as a valuable resource for burn wound research and treatment.

Examining the similarity of event environments or surroundings, more precisely settings, provides additional insight in analyzing event sequences as it provides information about the context and potential common factors that may have influenced them. This article proposes a new similarity measure for event setting sequences, which involve the space and time in which events occur. While similarity measures for spatiotemporal event sequences have been studied, the settings and setting sequences have not yet been studied. While modeling event setting sequences we consider spatial and temporal scales to define the bounds of the setting and incorporates dynamic variables alongside static variables. Using a matrix-based representation and an extended Jaccard index we developed new similarity measures that allow for the use of all variable data types. We successfully used these similarity measures coupled with other multivariate statistical analysis approaches in a case study involving setting sequences and pollution event sequences associated with the same monitoring stations, which validate the hypothesis that more similar spatial-temporal settings or setting sequences may generate more similar events or event sequences. In conclusion, these similarity measures have many potential real-world applications, and offer researchers a powerful tool for understanding different factors and their dynamics corresponding to occurrences of spatiotemporal event sequences.

The Roma population constitutes the largest ethnic minority in Europe, however, data regarding the prevalence of non- communicable diseases are still scarce in the medical literature. The aim of this study was to assess the clinical and metabolic particularities of a Roma population with diabetes, in comparison with a group of Romanian Caucasians. We conducted an observational, transversal study and evaluated 808 adult patients with diabetes mellitus, from a tertiary hospital providing diabetes care, aged between 18 and 89 years old, of whom the majority were men (52.84%). Most of them had type 2 diabetes mellitus (T2DM), reaching 95.1% the Caucasian group and 87.8% among the Roma patients. 81.1% of the Caucasian patients had hypertension, approximately 15% higher than the Roma group, while more than half of the patients in both groups had obesity. There were no differences concerning myocardial infarction, however, the number of patients with history of stroke was 2.1 times higher in the Roma group compared to Caucasians. Chronic kidney disease was present in 22.1% of the Roma patients, 33.25% had retinopathy, and 72.7% presented polyneuropathy. The prevalence of cardiovascular risk factors, cardiovascular disease and microvascular complications among the study Roma population are quite significant, underscoring the importance of ethnic disparities in approaching healthcare management strategies.

Considering rotation-induced centrifugal stiffening, spin softening, and Coriolis effects, the three-dimensional finite element model of a rotating blade with a dovetail structure is built through the contact dynamics theory. The fixed-interface component mode synthesis method is then adopted to reduce the model for high computational efficiency and adequate model accuracy. The effects of the number of normal modes on the first-six-order modal characteristics of the model varying with the rotating speed are studied between the reduced and full models. Next, the influence of rotating speed and friction factor on the nonlinear dynamic characteristics of the model under the action of aerodynamic force are elaborately discussed. The results show that: (1) tenon-mortise joint contact-induced nonlinearity under low rotating speeds results in the intermittent interference of contact surfaces and frequency multiplications of aerodynamic excitation frequency in the spectrum cascades, while that under high rotating speeds causes the continuous interface contact and asynchronous excitation at the tenon-mortise joint; (2) the increase of friction factor results in a lower contact pressure distribution and the right shift of the resonance peak (i.e., hard nonlinearity).

The goal of our article was to systematize studies that investigated the impact of living conditions in large national regions on individual alcohol consumption. We sought publications on the research topic in PubMed, Google Scholar, OpenGrey, Crossref and eLibrary databases from the moment they were created until December 31, 2021. After removal of duplicates and unsuitable publications, and full-text review of remaining published sources, the final sample included 81 publications. The majority of ultimately selected papers were published after 2010, represented the United States of America, and considered samples of children and youths, either the younger population or the general adult population. High quality was characteristic for 19 studies, while satisfactory quality was exhibited by 46 publications. The most consistent associations with individual alcohol consumption were revealed for the legislative environment (especially for integral scales and indices), alcohol pricing policy, the prevalence of alcohol consumption and binge drinking in the population, and unemployment rate. Among the shortcomings of the reviewed articles, we should mention the prevailing assessment of the impact of only one type of regional characteristics, as well as the lack of studies analyzing the interaction of environmental influence at the territorial level of different scales. Protocol PROSPERO CRD42021234874.

The work carried out first-principles calculations within the framework of density functional theory to study the structural stability of the CsSnI₃ compound and the influence of phase transitions on their electronic and optical properties. Using the GGA and SCAN functionals, the relaxed structures of the CsSnI₃ phases were obtained and their geometric characteristics were assessed. Using the Phonopy code based on VASP, calculations of phonon and thermodynamic properties were performed, and the temperatures of phase transitions of CsSnI₃ were determined. The temperature dependences of the thermodynamic parameters α-, β-, γ- and δ-phases of CsSnI₃ were analyzed. The trends in free energy, entropy, enthalpy, heat of formation energy and heat capacity were justified in terms of the pattern of changes in the total energy of the four phases of CsSnI₃ from VASP calculations. It is shown that at 0 K the non-perovskite structure of the CsSnI₃ compound (δ-CsSnI₃) is the most stable (followed by γ-CsSnI₃), and the tetragonal phase (β) is quite unstable, having the highest energy among the perovskite phases. It was revealed that at temperatures above 450 K the tetragonal phase becomes stable, and when the temperature drops, it transforms into the cubic phase (α-CsSnI₃). The phase transition between the β and γ phase of perovskite occurs in the range of 300-320 K, and at 320 K a black-yellow transformation of CsSnI₃ occurs in which the cubic phase (black perovskite) undergoes a phase transition to a non-perovskite conformation (yellow phase). The presence of temperature phase transitions between two orthorhombic phases of CsSnI₃ at 360 K was discovered, although direct transitions of the α⟷γ and γ⟷δ types have not yet been reported in any experiment, except for γ→δ transitions under the influence of moisture. Based on well-relaxed structures (from the SCAN calculations), the band gap widths for four CsSnI₃ phases were calculated and compared with experimental measurements. Electronic properties and Fermi level shifts as a result of phase transformations of CsSnI₃ were assessed using the HSE06 functional and machine learning prediction. The values of the complex dielectric constant and the refractive index of all phases of the CsSnI₃ were determined.

Diabetes is one of the fatal diseases that play a vital role in the growth of other diseases in the human body. Controlling and curing diabetes in its early stages is the most significant technique to avoid its effects of diabetes. However, lack of awareness and expensive clinical tests are the primary reasons to skip clinical diagnosis and take preventive methods in lower-income countries like Bangladesh, Pakistan, and India. From this perspective, the study aims to build an automated machine learning (ML) model, which will predict diabetes at an early stage using socio-demographic characteristics rather than clinical attributes. Because clinical features are not always known to all people from lower-income countries. To find the best fit supervised ML classifier of the model, we applied six classification algorithms and found that RF outperformed with an accuracy of 99.36%. In addition, the most significant risk factors were found based on the SHAP value by all the applied classifiers. The study reveals that polyuria, polydipsia, and delayed healing are the most significant risk factors for growing diabetes. The findings indicate that the proposed model is highly capable of predicting diabetes in the early stages.

The purpose of this work was to investigate whether two-months supplementation with 100% sea buckthorn juice (SBJ) would modify blood lipids, LDL subfractions and other markers of cardiovascular risk in hypercholesterolemic women. A group of 28 hypercholesterolemic non-medicated adult women with a mean age of 50.58 ± 5.76 years consumed 50 mL of 100% SBJ daily for two-months. We observed a significant reduction of body weight (BW; p < 0.05), body mass index (BMI; p < 0.05), body fat mass (BFM; p < 0.001) and visceral fat area (VFA; p < 0.001), on the contrary, a significant increase of skeletal muscle mass (SMM; p < 0.05) and fat-free mass (FFM; p < 0.05). Supplementation with 100% SBJ significantly increased the level of high-density lipoprotein (HDL; p < 0.05), reduced the level of low-density lipoprotein (LDL; p < 0.05), atherogenic LDL subfractions (LDL3–7; p < 0.05) and improved LDL/HDL ratio (p < 0.001). After the SBJ consumption, significant reduction of C-reactive protein (CRP; p < 0.001), orosomucoid (ORM; p < 0.001) and interleukin 6 (IL-6; p < 0.05) were found. In conclusion, consumption of SBJ showed an indication of beneficial effects on cardiovascular risk factors in hypercholesterolemic women.

The compositions of metalliferous sediments which is associated with hydrothermal vents can provide reliable geochemical indicators for the exploration of seafloor sulfides. In this study, surface sediments from the Xunmei hydrothermal field (HF) on the South Mid-Atlantic Ridge (SMAR) were selected, and their major and trace elements were analysed. The results showed that the sediments are composed of pelagic material (calcium biogenic components), basaltic debris, iron-manganese oxides, and a mixture of hydrothermal components. Additionally, the sediments were found to be significantly enriched in Cu, Zn, Fe and Co derived from hydrothermal sources, as well as Mn, V, Mo, U and P, which are primarily scavenged from seawater. The Cu and Zn concentrations are highest in the northeastern part of Xunmei, while the northeastern, northern, and southern parts are characterized by great inputs of hydrothermal Fe. Manganese and Mo are mainly enriched in the western and southern parts and show a strong positive correlation, indicating that Mo is mainly scavenged by Mn oxides. There are high positive correlations among U, P, and Fe, indicating their coprecipitation with Fe from hydrothermal plumes. Vanadium and Co are introduced into sediments in two ways, i.e., V is scavenged and coprecipitates from hydrothermal plumes, and Co is derived from sulfide debris. Based on the variations in Cu and Zn contents and in the Cu/Fe (0.159), Zn/Fe (0.158), and Fe/Mn (1440) ratios, it can be inferred that a high-temperature hydrothermal vent existed in northeastern Xunmei. In combination with the distribution patterns of the above elements, the hydrothermal vents in the southern part ceased erupting after a short period of activity. In addition, the high Mn anomaly and the high U/Fe ratios at the boundaries of the investigated area indicate the presence of a relatively oxidized environment in southwestern Xunmei.

The Korean water deer (WD), the dominant wildlife species in South Korea, is classified as vul-nerable on the IUCN Red List. Beside their several unique characteristics, they have a lower in-cidence of tick bites compared to other Cervidae species, particularly roe deer (RD). In natural environments, ticks exhibit questing behavior by waiting on grasses to climb onto host's hair coat. They use sensory organs to detect signals such as body temperature and chemicals from the host's skin, then move to preferred feeding location. Therefore, we conducted a comparative analysis of the skin tissue and hair features of both species to compare the factors leading to lower incidence of tick bites in WD. Notably, WD had significantly larger blood vessels, sebaceous glands, and sweat glands which maintain the barrier functions of the skin (p≤0.004), irregular scale surfaces in hair cuticles, and stiff and 2.83-times thicker primary hair diameter (p<0.001). Each parameters made the ticks difficult to move onto the epidermis of WD. To our knowledge, this is the first report which is focused on the comparative analysis for skin and hair feature in WD and RD. We suggest that these differences may attribute to evade tick bites in WD.

Many studies have focused on the impacts of rainfall duration and intensity while overlooking the role of rainfall patterns on intensive tillage erosion in hilly agricultural landscapes. The objective of this study was to determine the combined effects of rainfall patterns and intensive tillage erosion on surface runoff and soil loss on sloping farmland in the purple-soil area of China. Five simulated rainfall patterns (constant, rising, falling, rising-falling, and falling-rising) with the same total precipitation were designed, and the intensive tillage erosion treatment (IT) and no-tillage treatment (NT) were subjected to simulated rainfall using rectangular steel tanks (2 m × 5 m) with a slope of 15°. To analyse the differences in the hydrodynamic characteristics induced by tillage erosion, we calculated the flow velocity (V), Reynolds number (Re), Froude number (Fr), and Darcy-Weisbach resistance coefficient (f). The results indicate that significant differences in surface runoff and soil loss were found among different rainfall patterns and stages (P < 0.05). The falling pattern and falling-rising pattern had faster runoff-initiating times and larger sediment yields than those of the other rainfall patterns. f varied from 0.30 to 9.05 for the IT and 0.48 to 11.57 for the NT and exhibited an approximately inverse trend to V and Fr over the course of the rainfall events. Compared with the NT, the mean sediment yield rates from the IT increased the dynamic range of 8.34%–16.21% among different rainfall patterns. The net contributions of the IT ranged from 2.77% to 46.39% on surface runoff and 10.14%–78.95% on soil loss on sloping farmland. Surface runoff and soil loss were positively correlated with rainfall intensity, V, and Fr but negatively correlated with f irrespective of tillage intensive (P < 0.05). For varying-intensity rainfall patterns, soil and water loss fluctuated during rainfall events, suggesting that the changes in rainfall intensity and tillage intensity would result in drastic variations in soil hydrological characteristics and sediment transport mechanisms. The time sequences of rainfall intensity in each rainfall pattern significantly affected surface runoff, soil erosion, and their contribution rates to total soil and water loss. Moreover, tillage erosion effects on soil and water loss were closely related to rainfall patterns in hilly agricultural landscapes. Our study not only sheds light on the mechanism of tillage erosion and rainfall erosion but also provides useful insights for developing tillage-water erosion prediction models to evaluate soil and water loss on cultivated hillslopes.

The Planetary Roller Screw Mechanisms (PRSMs), alongside Ball Screw Mechanisms (BSMs) and Electromechanical Actuators (EMAs), occupies a pivotal role in advancing the precision and efficiency of various industrial applications, including aerospace, automotive, and high-precision machining tools. Despite their critical advantages such as high load capacity, superior precision, and extended lifespan, the deployment of PRSMs in complex operational conditions reveals a landscape rife with challenges and opportunities for further research. This comprehensive review endeavors to dissect the multifaceted aspects of PRSMs, focusing on their mechanics and dynamics, tribology and thermal behavior, and the paramount importance of reliability and condition monitoring. By synthesizing current research findings, this paper highlights the significant advancements in understanding the static and dynamic characteristics of PRSMs, the intricate interplay between lubrication conditions and wear mechanisms, and the critical role of thermal effects on operational performance. Moreover, it delves into the dynamic models that address the impact of manufacturing imperfections, such as waviness and defects, on the reliability of these mechanisms. Despite the strides made, the review identifies critical gaps in the existing literature, particularly under conditions of extreme temperatures, large deformations, and multifaceted loads, advocating for a holistic approach to research. By proposing integrated thermo-mechanical models and emphasizing the need for empirical validations, this paper outlines a roadmap for future studies aimed at facilitating the development of more robust and reliable PRSMs, capable of meeting the demands of complex operational scenarios and advancing the field of high-precision applications in aerospace, robotics, and beyond.

The safety of a pedestrian crossing may depend on infrastructure, vehicular and pedestrian traffic characteristics. This research portrays the safety challenges caused by vehicles on crosswalk in the City of Kigali. Through observing the stopping of drivers in pedestrian crossing events, the study aims to evaluate driver’s behaviors against traffic flow parameters. 10 collection sites were finally selected purposively and randomly to suit observations for data recording. A total of 10,259 crossing events were recorded within 280 hours. Statistical analysis, tests and Binary logistic regression model were used to evaluate the behaviors. Sadly,82.4% drivers violate crosswalks, endangering crossing. Motorcyclists exhibit the most aggressive behavior. Car drivers are relatively less aggressive,60% managed to brake in the events. Buses and bicycles share a negligible collective of 2%, being aggressive and would not stop. Cars are 10.389 times more likely to stop compared to bicycles. Having more vehicles in a row is safer to cross, for each unit increase on the vehicle density scale, there were 1.956 more chances that every driver would stop.13% to 21% of traffic variables predict the variance in stopping behaviors model.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

Among endocrine cancers, thyroid carcinoma is the most prevalent type of cancer. It's prevalence has been increased throughout the world during the last decades, which shows great regional variations. Considering the increasing prevalence and occurrence of thyroid cancer cases, in this study we: Among endocrine cancers, thyroid carcinoma is the most prevalent type of cancer. It's prevalence has been increased throughout the world during the last decades, which shows great regional variations. Considering the increasing prevalence and occurrence of thyroid cancer cases, in this study we decided to evaluate the clinical and pathological charactristics of this endocrine system cancer in the population of thyroid cancer patients reffered to imam Khomeini Hospital in Sari between March 2014 and March 2021. decided to evaluate the clinical and pathological charactristics of this endocrine system cancer in the population of thyroid cancer patients reffered to imam Khomeini Hospital in Sari between March 2014 and March 2021.

In recent years, additive manufacturing of products made from 5000 series alloys has grown in popularity for marine and automotive applications. In this work, we compare of mechanical properties characteristics of aluminum alloy 5056 material produced by wire-arc additive technology and rolling. We carried out tension tests under quasi-static loading and impact toughness tests under impact loading. The results show that upon similar ultimate tensile strength and ductility, material after additive manufacturing demonstrates decreased resistance against dynamic loading than material manufactured by the typical method of casting and rolling. This decrease in properties was explained through macro- and microstructure analysis.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

The paper is devoted to the study of a high-pressure short-arc xenon discharge, which is widely used as a light source. Cathodes of such lamps are often doped with thorium for better cathode operation. As a result, thorium can evaporate into a discharge. The study is based on a model of a short-arc xenon discharge plasma, which includes presence of thorium atoms in the plasma. The data obtained show that thorium atoms strongly affect the characteristics of the plasma, reducing its temperature, changing the ionic composition near the cathode, energy balance and generation of optical radiation. Especially interesting is the case when the discharge electrodes have a different shape of the working surface: the anode has a convex or concave shape; the cathode has a different cone angle. The obtained data make it possible to propose a new way to increase the luminous efficiency of xenon lamps due to the appropriate choice of the electrodes working surface shape, which turned out to be an unexpectedly strong factor of affecting plasma characteristics. This, in turn, allows us to develop xenon lamps with the desired characteristics providing optical radiation in the required range of the spectrum and better use of energy.

Authorities and governmental bodies strongly emphasize the importance of residents preparing for natural disasters, particularly underscoring the significance of readiness for geophysical hazards like earthquakes. In this study, which represents comparative quantitative research, the levels and predictors of the impact on preparedness for earthquake-induced disasters in South-Eastern Europe countries such as Montenegro, North Macedonia, and Serbia are examined. Using the snowball sampling technique (online questionnaire), a survey of 1245 respondents (Montenegro (n = 400), North Macedonia (n = 345), and Serbia (n = 500) was conducted from February 2023 to February 2024. The paper is based on the central hypothesis that the most significant predictor of earthquake preparedness in Montenegro, North Macedonia, and Serbia is age, followed by gender and education. Multivariate regression analysis was used to determine the extent to which five scores of the subscales (household preparedness, community preparedness, disaster preparation, earthquake risk awareness, reinforced house) were associated with seventh demographic and socio-economic variables. In addition to the mentioned analysis, other statistical analyses such as T-test, one-way ANOVA analysis, and Pearson correlation were also utilized. The results indicate that age emerges as a predictor in various aspects of earthquake-induced disaster preparedness and awareness in most models, followed by education. These findings confirm the significance of respondents' age in determining levels of preparedness and earthquake awareness. Overall, in North Macedonia, respondents recorded the highest ratings (M = 3.52) for household preparedness for earthquakes, compared to Montenegro (M = 2.98) and Serbia (M = 3.26), where the lowest ratings were recorded. Research findings, taking into account cultural characteristics, can serve as a basis for the development of targeted interventions, strategies, policies, and programs aimed at improving the level of societal preparedness for earthquake-induced disasters.

The concepts of fractional calculus and the related techniques have been gaining momentum in circuit system fields, and an increasing body of evidence suggests that fractional-order characteristics are widely distributed in electronic components. In this paper, we consider the fractional characteristics of non-solid aluminum electrolytic capacitors and focus on the nonlinear dynamic characteristics of peak-current-mode controlled (PCMC) dc-dc boost converters with such components. In the work, we establish a piecewise smooth non-commensurate fractional-order model to describe the converter, in which the fractional-order equivalent impedance model of capacitors is adopted and the detailed control loop is considered. In order to analyze the converter, we use the fractional Adams-Bashforth-Moulton typed method (F-ABM) and stroboscopic map technique to obtain the time-domain solutions and the bifurcation diagram. The results of bifurcation diagrams indicate that, with the change of different parameters, the converter enters chaotic state through period doubling bifurcation. In order to provide empirical evidence for the nonlinear dynamic analysis, we consider both circuit-level simulation and experiments in the work, the results of which further confirm the results of theoretical analysis.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

A numerical method using combined detached-eddy simulation (DES) and cavitation model considering the rotation effect is used for unsteady cavitation flow field of the centrifugal pump. Closed type pump test system was established to obtain the pump performance and pressure pulsation characteristics under different flow rates and cavitation condition, which provide boundary conditions and verification of calculations. Based on the calculation results of the unsteady flow field of the centrifugal pump cavitation, the entropy generation analysis of the flow field and the pressure fluctuation characteristics were carried out. Then the relationship between cavitation and the deterioration of the centrifugal pump performance and the generation of the unstable operation excitation force was tried to reveal. The internal energy loss is mainly concentrated in the impeller, volute, and pump cavity area, which accounts for more than 85% of the total entropy generation. The characteristic frequency of about 0.333 Strouhal Number appears at the volute tongue due to the cavitation flow spread downstream.

Soil salinity is seen as a major restriction for crop production, and with water scarcity this problem becomes more complicated. Mulching is crucial to salinity dynamics management by decreasing evaporation with improving the soil’s characteristics. Using chitosan as an eco-friendly biostimulant can enhance plant defense genes during different abiotic stresses. Recently, agricultural research has recognized nanoparticles as a pioneer material due to their distinctive physicochemical features. Therefore, a lysimeter experiment was conducted to investigate the interactive effects of mulching (UNM: un-mulched, WPM: white plastic, RSM: rice straw and SDM: sawdust) and chitosan foliar application (Ch0: control, Ch1: 250 mg chitosan L-1, Ch2: 125 mg nano chitosan L-1, and Ch3: 62.5 mg nano chitosan L-1) on the biochemical soil characteristics and common beans productivity under salt affected soil conditions. Organic mulching (RSM and SDM) treatments significantly improved the soil's organic carbon, available nutrient content, and total count of bacteria. WPM treatment lowered soil EC to 6.63 dS m-1 and increased soil water content to 34.13%. The application of Ch3 caused considerable increases in the plant height, shoot dry weight, root dry weight, grain yield, and nutrient content in the seed. The total fungi count in the soil and Na% in the seed was significantly decreased due to chitosan foliar applications. Moreover, the interactive effect of different mulch materials plus foliar by chitosan applications gave a statistically similar seed yield in both seasons. Overall, this study revealed the potential of the mulching treatments and foliar application of nano chitosan in improved biochemical soil characteristics and common bean productivity under saline soil conditions.

Three new species of the Sequester group of Pteromalus (Habrocytus) (Hymenoptera: Pteromalidae: Pteromalinae), Pteromalus (Habrocytus) boleensis Yan et Li sp. nov., Pteromalus (Habrocytus) longepedicelus Yan et Li sp. nov., and Pteromalus (Habrocytus) robustus Yan et Li sp. nov. are described and illustrated based on adult morphology and molecular data from Xinjiang, China. The DNA barcodes (ITS2) of Pteromalus (Habrocytus) boleensis sp. nov. and Pteromalus (Habrocytus) robustus sp. nov. have been generated and compared with all existing sequences of the Sequester species group. The results of morphological taxonomy and molecular identification are consistent. A key to all known species of the Sequester group in the world is provided.

The goal of our study was to examine the effect of regional characteristics of living environment on individual a priori and a posteriori dietary patterns of the Russian population. For the analysis, we used cross-sectional data from the Epidemiology of Cardiovascular Diseases in the Regions of the Russian Federation study of 2013-2014. The sample included 18,054 men and women 25-64 years of age from 12 regions. Based on the frequency of consumption of basic foods, four a posteriori empirical dietary patterns (EDPs), along with an a priori cardioprotective dietary pattern (CPDP) were identified. To describe the regional living environment, 5 regional indices were used. The adherence to the meat-based EDP was directly associated with deterioration of social living conditions and the more northerly location of the region of residence. The probability of CPDP increased with deterioration of social living conditions, an aggravation of demographic crisis, higher industrial development of the region, as well as with a decline in the economic development of the region, income and economic inequality of the population. We detected some gender-dependent differences in associations. The revealed patterns reflect the national dietary preferences of Russians, and regional indices characterize the effect of living environment.

The study provide insights into the technological characteristics of green practices adoption and the potential benefits they offer in terms of socio-economic development, environmental and public health. The study adopted a cross-sectional research design. A structured questionnaire was developed to collect quantitative data from the participants. The questionnaire include closed-ended questions, Likert scale items, and demographic questions. Both stratified and simple random sampling techniques were employed to select the study participants (government officials, employees, managers, and community members). A total of 321 copies of questionnaires were duly filled and returned. The collected data were analyze using descriptive statistics, such as frequencies, percentages, mean, and standard deviation, were used to summarize the data and provide an overview of the key variables related to green practices adoption. The findings indicate that the manufacturing company in Ogun State, Nigeria, has shown moderate commitment to adopting green practices. While there is room for improvement in certain areas, such as waste-to-energy technologies and green building practices. Additionally, green practices have positively influenced employee well-being and community health, while aligning with the company's commitment to safeguarding the environment and public health.

Safe water is a global public health concern amid increasing scarcity and pollution. Bottled water production and consumption contribute to these problems. This study examines tap water consumption in Italy, assessing associated sociodemographic factors and related health outcomes such as obesity and self-perceived health status. Data from the Italian National Statistics Institute's "Aspects of daily life" survey (N=45,597) were analyzed. Covariates included education, age, gender, economic status, region, concerns about waste and climate change, consumption of carbonated drinks excluding water, alcohol consumption, consumption of vegetables, consumption of snacks, body mass index, and self-perceived health status. Bivariate analyses and mixed-effect logistic regression models explored the associations. People who drink tap water were 19,674 with a higher prevalence in people aged 45 to 59 old, people with a graduate/post-graduate degree diploma, with optimal economic resources, and concerned about waste production and climate change, coming from the North-East regions of Italy. Underweight people showed a higher prevalence of TW assumption as well as those who drink less than occasionally carbonated drinks, drink alcohol, consume vegetables more than once a day, and snacks less than once a week with a satisfying level perceived health status. Regressions showed that all age classes are less likely to drink tap water than people younger than 20 years old. The category with “inadequate” economic resources is more likely to consume tap water. Low educational classes show a low likelihood of consuming tap water as well as Islands. A concern about waste production and climate change is associated with an increased likelihood of assuming tap water. Tap water consumption was negatively associate with obesity but not with a satisfactory Self-perceived health status. Insights from this study can inform public health strategies.

We examine here characteristics of electromagnetic waves that propagate through an unbounded space filled with a homogeneous isotropic chiral medium. Resulting characters are compared to those of the electromagnetic waves propagating through an achiral free space. To this goal, we form energy conservation laws for key bilinear parameters in a chiral case. Due to a nonzero medium chirality, conservation laws turn out to contain extra terms that are linked to the spin-orbit coupling, which is absent for an achiral case. As an example, we take a plane wave for achiral case to evaluate those bilinear parameters. Resultantly, the conservation laws for a chiral case are found to reveal inconsistencies among several bilinear parameters that constitute the con-servation laws , thereby prompting us to establish partial remedies for formulating proper wave-propagation problems.

Driven by industrialization and urbanization, urban air pollution can increase respiratory, heart, and cerebrovascular diseases, and thus mortality rates; as such, it is necessary to improve air quality through the consideration of individual pollutants and emissions sources. In South Korea, national and local governments have installed urban and roadside air quality monitoring systems. However, stations are lacking outside metropolitan regions, and roadside stations are sparsely distributed, limiting comparisons of pollutant concentrations with vehicle traffic and floating population levels. Local governments have begun using mobile laboratories (MLs) to supplement the fixed measurement network and investigate road pollution source characteristics based on their spatiotemporal distribution; however, the collected data cannot be used effectively if they are not visualized. Here, we propose a method to collect and visualize global information system (GIS)-based air quality data overlayed with environmental variables to support air quality management measures. Spatiotemporal analyses of ML-derived data from Bucheon, Korea, confirmed that particulate and gaseous pollutant concentrations were high during typical commuting hours, at intersections, and at a specially managed road. During commuting hours, the maximum PM10 concentration reached 200.7 µg/m³ in the Nae-dong, Gyeongin-ro, and Ojeong-dong ready-mix concrete complex areas, and the maximum PM_2.5 concentration was 161.7 µg/m³. The maximum NOx, NO₂, and NO levels of 1.34 ppm, 0.18 ppm, and 1.18 ppm, respectively, were also detected during commuting hours. These findings support the need for targeted management of air pollution in this region, and highlight the benefit of comprehensively comparing road levels, driving speed, and traffic levels when identifying hotspots of air pollution. Such analyses will contribute to the development of air quality management measures customized to regional characteristics.

With the increase of global human activities, a large number of technogenic magnetic particles (TMPs) generated by industrial activities such as coal combustion, traffic and so on enter sediments on continental shelves. However, there is currently a lack of understanding of the spatiotemporal distribution of TMPs on continental shelves, as well as the sedimentary effects they cause. This review work comprehensively analyzes the source, morphology, composition, and spatiotemporal distribution characteristics of TMPs. Then it elucidates their magnetic contribution to sedimentary environments in continental shelf seas, as well as the influence of heavy metals and active iron. At the same time, the existing problems and future development directions of TMPs on continental shelves are summarized.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

Because of the large number of parameters that interact in their function, determining dynamic regime parameters as well as the mode of function of amplifying stages is an extremely complex problem. This paper describes a LabVIEW application for studying the functioning of an ampli-fier in various connections. The user selects the generator's parameters, the type of connection and its parameters, as well as the electric charge characteristics. The application can determine both the stage characteristics and the Bode characteristics. The amplifier's stability zone, as well as its gain and phase, are determined based on these characteristics. An important advantage of this application is that the design of the amplifier stage can be made starting from some param-eters that the amplifier can establish, from which the values of components can be determined. In order to validate the simulation results using the LabVIEW application, a specialized program Multisim was used, as well as experimental measurements using the Electronics Explorer Board. Both Multisim and Electronics Explorer Board can determine Bode characteristics. In both simu-lations and experimental amplifiers, the same schemes with the same transistor was used. The application can be used for educational purposes as well as to design the amplifier's stage to achieve specific parameters.

The present study finds the association of board characteristics (such as gender diversity, independence, female chairperson or/and female CEO, and board size) and the quality of Corporate Social Responsibility (CSR) disclosure of the top 100 Pakistan Stock Exchange (PSX) listed companies. Unlike most earlier studies in similar contexts, we have focused on CSR disclosure ‘quality’ and not ‘quantity’. We conducted the content analysis of secondary Corporate Governance (CG) and CSR data extracted from the annual reports of PSX-listed companies across ten industrial sectors from period of 2017 and 2018. Our empirical investigation through univariate and multiple regression analysis with Ordinary least squares (OLS) techniques revealed that all the board characteristics potentially have a significant association in lessening CSR disclosure quality. We acknowledge several research limitations, including the study time period and selected board characteristics. While our study has provided some understanding of the association of board characteristics with CSR disclosure quality of PSX-listed companies, several research gaps still need to be addressed. Future investigators should examine this association through the pre-COVID-19 and post-COVID-19 connections and the inclusion of a systems theory perspective.

Wastes from social economic activities had great impact on water quality thereby limiting water usability for domestic purposes. Sewages discharge from people activities, usually consist of undesirable concentrations of soluble chemicals that infiltrate into the surrounding surface and underground water, and then constitute health risk to the populace. In order to investigate the concentration characteristics and health risk for the local residents in Nandong Underground River Watershed (NURW), eleven common heavy metals in the water body analysis were conducted. Health risk assessment (HRA) was taken to analyze eleven heavy metals of 84 water samples from surface and underground waters in NURW: 36 samples underground water and 48 samples surface water. Our results showed that the heavy metals concentration order is that of Fe > Al > Mn > Zn > As > Cd > Pb > Cr > Ni > Cu > Hg. Correlation analysis indicates that these eleven metal elements have certain similarity on material source and migration transformation. The health risks for local residents exposed to metal elements in the water of NURW mainly from carcinogenic risk (10−6～10−4 a−1) through drinking way, and the health risk of heavy metals exposed to children through drinking way was much higher than adults. The maximum exposing health risks of Cr in both underground and surface water were higher than the recommendation standard (5.0×10-5 a-1) from ICRP, and all the values over the standard (5.0×10-6 a-1) recommended by the Swedish Environmental Protection Agency and the Dutch Ministry of Construction and Environment and the British Royal Society. The results of health risk assessment shows that Cr in the water of NURW was the mainly source of carcinogenic risk for the local residents, following by Cd and As. Consequently, it is necessary to control the three carcinogenic metals when the water was used as drinking water source.

Carbon, which exists in large quantities on Earth, is a material with interesting properties, and many studies have been conducted since the past. In particular, nano-sized carbon allotropes are called carbon nanomaterials, and many studies are currently underway. Among them, carbon nanowall (CNW) is a structure in which graphene of sp2 bond is grown vertically, CNW have outstanding strength, can be highly electrically conducting or semiconducting, have a large specific surface area per unit mass. Electrical, chemical, physical properties of these CNW is modified by parameter such as surface density, height and thickness of it. Those have great effect on CNW and can be adjusted as growth interlayer. It was confirmed that the molybdenum disulfide (MoS2) interlayer synthesized by radio frequency (RF) magnetron sputtering altered the morphological characteristics such as the shaped edge of the CNW, the pores diameter and density. Through these studies, we confirmed the effect of MoS2 on the morphological characteristics of CNW. This opens the door to improving the performance of electrodes and devices.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Yersiniosis is a common zoonotic enteral disease among humans, which has been linked to pigs and contaminated food, especially pork. Studies on yersiniosis in pets are very scarce. In this study, we performed pheno- and genotypic characterization of 50 Yersinia strains isolated from pets in Finland between 2012 and 2023. Y. enterocolitica 4/O:3/ST135, the most common type in human yersiniosis, was also the most common Y. enterocolitica type (68%) found in clinical faecal samples in our study. Also, human pathogenic Y. enterocolitica 2/O:9/ST139 and Y. pseudotuberculosis O:1/ST9 and O:1/ST42 strains carrying all essential pathogenic genes were identified. Three Y. enterocolitica 4/O:3/ST9 strains were multi-drug resistant and two of them were highly related showing one allelic difference (AD) with core-genome multi-locus sequence typing. Non-pathogenic, genotypically highly diverse Y. enterocolitica 1A strains, showing more than 1000 ADs and missing the essential virulence genes, were also recognized in dogs and cats. Our study demonstrates that pets can excrete human pathogenic Y. enterocolitica and Y. pseudotuberculosis in their faeces and may serve as an infection source for human yersiniosis, especially in families with small children in close contact with their pets.

Food Neophobia (FN), defined as the reluctance to eat new or unfamiliar foods, mainly concerns fruit, vegetables, and legumes, typical of the Mediterranean Diet (MD). Considering these premises, this study aimed to clarify the relationship between FN and AMD in a sample of Italian children and their association with some socio-demographic factors and children's nutritional status. A sample of 288 children aged 3-11 years, participated to an assessment carried out with a questionnaire evaluating FN and AMD, respectively with Child Food Neophobia Scale (CFNS) and the KIDMED Test. Most of the sample showed an intermediate (67.3%) or high level of FN (18.1%) with high rates among 6-11 years old children (63.9%) and especially in only-child (50%). The AMD was mostly low (29.5%) or medium (54.8%) and reached lower levels among higher neophobic children (51.9%; p value &lt; 0.05). Present results confirm the study hypothesis that FN is a driver of MD abandonment and show the positive effects on children's eating habits of having siblings. Finally, this study proves the relevance of adopting effective feeding strategies against FN to avoid its maintenance in adulthood and detrimental effects on future overall health and well-being.

Satellite measurements are one of the main sources of data on the state of the marine environment. To obtain information about the sea brightness coefficient , it is needed to correctly carry out atmospheric correction. In the presence of dust aerosol over the Black Sea, physically incorrect values of the spectral brightness coefficient often occur, and specifically negative values in the IR region of the spectrum. The main objective of the study is to evaluate the influence of dust aerosol on the spectral dependence of sea brightness, based on analytical calculations from the transfer theory using the principle of plane-parallel layers and results of validation of AERONET-OC field and remote sensing data. The work analyzes spectral dependence of the first error eigenvector of the standard atmospheric correction in the presence of dust aerosol. As result it is given that with an absorbing aerosol, the atmospheric correction error is described by the spectral course of molecular scattering, i.e. close to

The Gulong shale oil reservoir is formed in freshwater to slightly saline lacustrine basins, mainly consisting of pure shale geological structure, which is quite different from other shale reservoirs around the world. Currently, the development of Gulong shale oil mainly relies on hydraulic fracturing, while the subsequent shut-in period for imbibition has been proven to be an effective method for enhancing shale oil recovery. To clarify the characteristics of fluid occurrence space and the variation of fluid occurrence during saltwater imbibition in Gulong shale, this paper carried out porosity and permeability tests on Gulong shale cores, and analyzed the fluid occurrence space characteristics and imbibition oil recovery based on nuclear magnetic resonance (NMR). In the porosity and permeability tests, the porosity measured by saturation method was calibrated using NMR T2 spectra. Combined with the identification of fractures in shale cores using micro-CT and the analysis of porosity and permeability parameters, it was found that the permeability of shale cores was related to the development of fractures in shale cores. Through the testing and analysis of NMR T1-T2 two-dimensional spectra of the shale cores before and after saturation with oil, it was found that the shale mainly contains heavy oil, light oil, and clay-bound water, and they were distributed in different positions in the T1-T2 spectrum. Finally, the T1-T2 two-dimensional spectra of the shale core at different imbibition stages were analyzed, and it was found that the saltwater mainly entered the minuscule inorganic pores of clay minerals during the imbibition process, and squeezed the larger-sized inorganic pores containing light oil through the hydration expansion effect, thus expelling the light oil from the shale core and achieving the purpose of enhanced oil recovery.

This study investigated the anatomical characteristics and pulp quality of tapped Styrax sumatrana wood to facilitate its further utilization. The transverse surface of the tapped S. sumatrana was light or greyish brown in the sapwood and reddish brown in the heartwood. The resin canals of the tapped wood were formed along the growth rings at the boundaries between the heartwood and sapwood. Furthermore, microscopic analyses revealed an irregular outline and rounded epithelial cells at the edges of the intercellular traumatic resin canal (TC). Approximately 8–16 epithelial cells surrounded the resin canals. The fibers in the tapped S. sumatrana were generally thin-walled, whereas those near the TC were thick-walled. Moreover, S. sumatrana were diffuse-porous and exhibited intermediately distinct or indistinct growth ring boundaries. The vessels were mainly in radial multiples and clusters of 3–5. In addition, they showed a diagonal-to-radial pattern arrangement and a few tangential bands. Deposits were observed in some vessels in the tapped part but were absent in the untapped part. The fiber length of the tapped S. sumatrana wood was classified as moderate to extensive and categorized as 2nd grade pulp quality. Finally, the cell walls were classified as thin to moderate.

Hypertrophic cardiomyopathy (HCM) is a common inherited cardiac disorder characterized by marked clinical and genetic heterogeneity. Ethnic groups underrepresented in studies may have distinctive characteristics. We sought to evaluate the clinical and genetic landscape of Russian HCM patients. A total of 193 patients (52% male; 95% Eastern Slavic origin; median age 56 years) were clinically evaluated, including genetic testing, and prospectively followed to document outcomes. As a result, 48% had obstructive HCM, 25% had HCM in family, 21% were asymptomatic, and 68% had comorbidities. During 2.8 years of follow-up, the all-cause mortality rate was 2.86%/year. A total of 5.7% received an implantable cardioverter-defibrillator (ICD), 21% septal reduction therapy. Sequencing analysis of 176 probands identified 64 causative variants in 66 patients (38%); recurrent variants were MYBPC3 p.Q1233* (8), MYBPC3 p.R346H (2), MYH7 p.A729P (2), TPM1 p.Q210R (3) and FLNC p.H1834Y (2); 10 were multiple variant carriers (5.7%); 5 had non-sarcomeric HCM, ALPK3, TRIM63 and FLNC; thin filament variant carriers had a worse prognosis for heart failure (HR = 7.9, p=0.007). In conclusion, in the Russian HCM population, the low use of ICD and relatively high mortality should be noted by clinicians; some distinct recurrent variants are suspected to have a founder effect; family studies on some rare variants enriched the worldwide knowledge in HCM.

Globally, workplace stress and anxiety are at an all-time high, with 42% of employees experiencing daily work-related stress and anxiety. Drawing from workplace anxiety (WA) theory (Cheng &amp; McCarthy, 2018), we advance a model that considers four job demands – role ambiguity, work overload, job insecurity, and work-home conflict – as sources of daily WA, and in turn the downstream effects of WA on psychological capital (PsyCap). Our model posits gender as a moderator of the association between job demands and WA, and digital technology characteristics as moderators of the association between WA and PsyCap. We tested our predictions on a sample of 162 South African employees. Consistent with our predictions, we found positive effects of job demands on WA, with the relationship being stronger for females. Contrary to expectations, we found positive effects of WA on PsyCap, suggesting an adaptive function of WA. Perceived ease of use of digital technology moderated the association between WA and PsyCap, such that the association was strong at higher levels of perceived ease of use. This research advances our understanding of the sources of WA, the adaptive function of WA, and predictors of PsyCap. Broadly, our study adds to understanding emotions’ impact on workplace behavior.

Rubber compounds based on styrene-butadiene rubber, ethylene-propylene-diene-monomer rubber and the combinations of both rubbers were cured with different sulfur and peroxide curing systems. In sulfur curing systems, two type of accelerators, namely N-cyclohexyl-2-benzothiazole sulfenamide, tetramethylthiuram disulfide and combinations of both accelerators were used. In peroxide curing systems, dicumyl peroxide, and combination of dicumyl peroxide with zinc diacrylate or zinc dimethacrylate, respectively were applied. The work was focused on investigation of the curing system composition as well as type of the rubber or rubbers combinations on curing process, cross-link density and physical-mechanical properties of vulcanizates. The dynamic-mechanical properties on the selected vulcanizates were examined, too. The result revealed correlation between the cross-link density and physical-mechanical properties. Similarly, there was recorded certain correlation between cross-linking degree and glass transition temperature. The tensile strength of vulcanizates based on rubbers combinations was higher when compared to that based on pure rubbers, which points out the fact that by rubbers combination, not only the features of both elastomers can be combined, but also improved tensile characteristics can be achieved. When compared to vulcanizates cured with dicumyl peroxide, materials cured with sulfur system exhibited higher tensile strength. By application of co-agents in peroxide vulcanization, the tensile strength overcame the tensile behavior of sulfur cured vulcanizates.

The use of acoustic and magnetic methods of non-destructive testing to detect zones of stable localization of deformation in order to assess and predict the performance of long-term equipment is of scientific and practical interest at present. A structural-mechanical criterion has been developed, that reflects the revealed relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests in the metal of long-term equipment made of structural 0.2 С steel and heat-resistant 0,12C-1Cr-1Mo-1V steel. The values of the structural-mechanical criteria Ks.-m for structural 0.2 С steel and for heat-resistant 0,12C-1Cr-1Mo-1V steel, corresponding to the moment of stable localization of deformation, are established. At the same time, it is recommended to replace the checked equipment nodes due to the exhaustion of the resource. The proposed and justified approach to assessing and predicting the performance and residual life of long-term power equipment, based on the identified relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of the structural-mechanical criterion, was applied at a number of power plants in the Kemerovo region – Kuzbass. A methodology has been developed for evaluating the residual life, based on the identification and use of relationships between structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of a structural-mechanical criterion.

Recently, volatile organic compounds (VOCs) have been shown to act as precursors of secondary organic particles that react with ultraviolet rays in the atmosphere and contribute to photochemical smog, global warming, odor, and human health risks, highlighting the importance of VOC management. In this study, we measured VOC concentrations in various contexts including industrial and residential areas of Bucheon, Korea, through mobile laboratory and proton-transfer-reaction time-of-flight mass spectrometry methods to determine winter VOC concentrations, visualized the data based on spatial information, and used the results to develop an air quality management plan. For this purpose, global information system (GIS)-based air quality data and various environmental variables were comprehensively reviewed to assess spatial and temporal concentrations in three dimensions rather than in tables and graphs. Among VOCs, the levels of toluene, methanol, and n+i-butene were relatively high, with average concentrations of 48.3 ± 67.2, 34.4 ± 102.7, and 32.6 ± 57.7 ppb, respectively, at the end of the working day. The highest concentrations occurred near the Ojeong Industrial Complex. Mobile pollution sources are also a major driver of VOCs, highlighting the necessity of comprehensively reviewing traffic variables such as road level, estimated traffic volume, and average speed when identifying hotspots of air pollution. GIS-based visualization analysis techniques will improve the efficiency of air quality management.

The investigation of the spatiotemporal propagation characteristics of the "meteorological-agricultural-hydrological" drought system, under diverse climatic conditions, is crucial for the development of a robust drought warning system and the effective implementation of proactive drought prevention and resilience strategies. To achieve this, the current study utilizes the Soil and Water Assessment Tool (SWAT) model to simulate key components of the watershed water cycle, such as evaporation, surface water, soil water, and groundwater. Specifically, the Standardized Precipitation Evapotranspiration Index (SPEI), the Standardized Soil Moisture Index (SSMI), and the Nonlinear Joint Hydrological Drought Index (NJHDI) are employed to characterize meteorological drought, agricultural drought, and hydrological drought, respectively. By analyzing the correlation between these types of drought, the propagation characteristics of the "meteorological-agricultural-hydrological" drought system are elucidated using the rigorous strongest correlation coefficient method. The Yellow River Basin (YRB) is chosen as the case study for this research. Results showed that (1) The propagation time from meteorological to agricultural drought exhibited distinct seasonal characteristics, with durations of 5-6 months in spring, 2-3 months in summer, 3-5 months in autumn, and 6-8 months in winter. Compared to 1961-1990, the propagation time increased in spring and summer but decreased in autumn and winter during 1991-2010 for most YRB regions. (2) The agricultural to hydrological drought propagation showed no clear seasonal differences but increased over time. Specifically, zone C (arid/semi-arid with moderate temperatures) had shorter propagation time of 1-5 months, while zones B (transitional plateau to mid-latitude) and E (semi-arid/semi-humid temperate continental climate) experienced longer propagation time of 7-12 months. (3) Despite the extended timescales, agricultural-hydrological drought correlation was weaker than meteorological-agricultural linkage. This is because meteorological deficits directly reduce soil moisture, rapidly inducing agricultural drought. However, groundwater sustaining baseflow during agricultural drought delays streamflow deficits, prolonging the agricultural-hydrological propagation time.

A two-way coupled model between polydisperse particle phases with compressible gases and a density-based coupling implicit solution method combining the third-order MUSCL with QUICK spatial discretization scheme and the second-order temporal discretization scheme are constructed based on the discrete-phase model (DPM) and the stochastic wander model (DRWM) in the Eu-lerian-Lagrangian framework in conjunction with a unitary particulate source (PSIC) approach and the SST k-ω turbulence model. The accuracy of the numerical prediction method is verified using previous supersonic nozzle gas-solid two-phase flow experiments. Numerical simulation of two-phase jet of dry powder extinguishing agent gas with pilot-type supersonic nozzle was carried out to analyze the influence of geometrical parameters such as length ratio rL and area ratio rA of main nozzle on the two-phase flow field as well as on the jet performance indexes such as particle mean velocity vp,a, velocity inhomogeneity Φvp, particle dispersion Ψp, particle mean acceleration ap,a and so on. By analyzing the parameters, we indicate the requirements for the combination of jet performance metrics for different flame types such as penetrating, spreading, and dispersing.

By using various skill scores and spatial characteristics of spatial verification methods and tradi-tional techniques of the model evaluation tool (MET, V10.0.0), the gridded precipitation obser-vation CMPAV (V2.0) and three datasets that derived from local (LOC), Shanghai (SHA), and Grapes (GRA) model respectively are conducted to assess the 3 lead day rainfall forecast with 0.5-day intervals during summer of 2020 over central east China. Results have shown that LOC generally outperforms the other two for most skill scores but usually with relatively larger un-certainties than SHA, and it has the least displacement errors for moderate rainfall among the three datasets. However, the rainfall of GRA has been heavily underestimated and accompanied with large displacement error. Both LOC and SHA have shown almost equitable abilities in forecasting convection and rainstorms of the large area but with a slightly over-forecast of local convection, while LOC likely over-forecasts the local rainstorms. In addition, SHA slightly favors over-forecast on a broad scale range and a broad threshold range, and LOC slightly misses the rainfall exceeding 100 mm. Generally, for a broadly comparative evaluation on rainfall, the popular dichotomous methods should be recommended under considering reasonable classifi-cation of thresholds if the accuracy is highly demanded. And most spatial methods should be suggested to conduct with proper pre-handling of non-rainfall event cases. Especially, the veri-fications including spatial characteristic difference information could be recommended in a computationally sufficient environment.

With more and more transportation tunnels have been and will be constructed in loess areas in Northwest China with high earthquake potential, the overall stability of portal section under earthquakes actions and the related aseismic countermeasures attracted the attentions from both the scholars and engineers, especially the tunnels in the upper slope connecting the high bridges crossing rivers or valleys. In order to study the dynamic response characteristics and damage evolution of steep loess slope with a tunnel under the earthquake actions, a large-scale shaking table tests were performed on steep loess slope with a tunnel. Wenchuan-tangyu (WT) wave and El Centro (El) wave records were applied on the model to investigate the displacement response and acceleration response of loess slope with a tunnel under the horizontal (X) and the combined action of horizontal and vertical (X-Z) seismic loads, respectively. In particular, three-dimensional non-contact optical measurement techniques were used to obtain the slope surface displacements. The results showed that the main deformation pattern of the slope was horizontal movement and settlement when the seismic wave input was in the X and X-Z directions, respectively. However, the X direction seismic wave had a greater impact on the deformation of the slope, and the tunnel portal slope was destroyed under the action of a large horizontal seismic acceleration finally. Slope failure ahead of a tunnel could be divided into four stages, i.e. elastic deformation stage, plastic deformation accumulation stage, local failure stage, and overall failure stage. The peak ground displacement of X direction (PGDX) and peak ground displacement of Z direction (PGDZ) of the slope surface increased with the increasing of the input peak ground acceleration (PGA) when the input wave was same waveform and same direction. The existence of the tunnel had a great influence on the PGA and the PGA amplification factor (PGAAF) of the soil mass surrounding it. This was because the seismic waves encounter a tunnel surface with clear differences in the physical properties of the medium during their propagation in the slope, thereby forming a strong reflection and refraction effect, and the amplitude changed significantly. Numerical simulation results were basically consistent with the experimental results.

The survey findings reveal that rivers worldwide carry an annual sediment load of 15 billion tons into the sea, and the Yellow River basin alone contributes 1.6 billion tons of sand. Therefore, understanding the science of wind and sand in the Yellow River is crucial to ensuring the safe development of similar basins across China and the world. This study examines the midstream wind and sand area of the Xiliugou tributary, a part of the upper Yellow River. The researchers used a stepped sand collector combined with an anemometer to measure the sand transport flux at 0-50 cm height on various underlying surfaces of the basin. Then, they estimated the amount of wind and sand entering the Yellow River using a function model based on the measured factors. Furthermore, the team analyzed the particle size composition of wind-eroded sand to better understand the principles of wind and sand erosion and accumulation in the basin. The results of the study show that the sand transport flux per unit area varies significantly across different underlying surfaces. Moreover, the contribution of moving sandy land, semi-fixed sand, and fixed sand to wind and sand deposition in the Yellow River basin was 77.08%, 15.30%, and 7.62%, respectively. The vertical change of sand transport rate on the basin's surface demonstrates that the total sand transport rate is an exponential function of wind speed. Based on this relationship, the researchers estimated that the total annual average wind and sand entering the Yellow River basin via the Xiliugou tributary is approximately 8.09×105t. Due to the basin's unique geography and sand source, the particle size composition of wind-eroded sand differs between the east and west sides of the river channel. On the west side, desert sand, mainly fine sand, and very fine sand constitutes the sand source. Conversely, on the east side, sand collected in the riverbed by secondary wind erosion is the primary sand source. Furthermore, human activities have disturbed the grain composition, mainly comprising powder and clay particles. This phenomenon, known as "wind-blown mud and water-washed sand," is evident in this geographical unit. In conclusion, the Yellow River basin still faces significant ecological security hazards. Understanding the coupling relationship between desert-basin-sand and wind is the foundation for effectively controlling wind and sand flow into the Yellow River basin.

In the interaction of the rolling stock and the upper structure of the railway track, intense dynamic loads occur. They have a destructive effect both on the parts of the rolling stock and on the elements of the superstructure of the track. In order to develop a durable, rational and reliably functioning design of cars and locomotives with good dynamic properties and good indicators of the impact of rolling stock on the railway track, along with theoretical computational studies, experimental studies are also required, which are usually the final stage in the design and implementation of rolling stock or modernization of existing ones. Locomotives and wagons in order to improve their strength and dynamic performance. The article presents the results of field tests to determine the dynamic performance of the type CKD6e diesel locomotive. The description of the preparation of the CKD6e shunting locomotive for testing is given. An analysis of the dynamic performance of a diesel locomotive during the passage of turnouts, on a straight section of the track and in a curve with a radius of 400 m, was carried out. The studies performed showed that the minimum value of the stability factor against wheel derailment on a straight section of the track is significantly higher than the standard value. The experimentally obtained ratio of frame forces to the static load from the wheelset on the rails, the coefficients of vertical dynamics of the first and second stages of suspension and the coefficient of stability against derailment of the wheel from the rail, registered on the track section in a curve with a radius of 400 m) meet the current requirements. A calculation scheme and equations of vertical oscillations are proposed, an analysis is carried out according to the graphs of movements of bogies and a locomotive body when moving along irregularities of different lengths at different speeds.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity or remain stress-free. Contrary to this are shell structures, which can bridge large spans with little material if designed well. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behaviour on a smaller scale by dissolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is to be developed in an ongoing research project, basic analysis approaches of which are presented in this paper. In addition to the basic workflow and the programs used, the material models used, and their calibration are described on the basis of tests on textile reinforced concrete (TRC) samples. Initial tests on two individual TRC served to verify the model.

Exploring the spatio-temporal differentiation characteristics and coupling coordination relationship of the composite ecosystem of urban agglomerations is of great significance for promoting the synergistic development and integration construction of urban agglomerations. This paper is based on LUCC data, DEM, temperature, precipitation and other multi-source data, taking the central Yunnan urban agglomeration as an example. The entropy weight method is first used to determine the comprehensive weights to evaluate the regional economic and social development level. Then, the InVEST (Integrated Valuation of Ecosystem Services and Trade-offs)model was used to quantitatively calculate and analyze the spatial and temporal evolution characteristics of the four ecosystem services, including water conservation, soil conservation, carbon sequestration services, and habitat quality. The coupling coordination model was used to quantitatively analyze the evolution of the coupling coordination of the composite ecosystems in the central Yunnan urban agglomeration during the period of 2010-2020, and to reveal its development law. The results show the following: ①During the study period, the socio-economic subsystems in central Yunnan urban agglomeration demonstrated an outward radiative growth from Kunming City, marked by underdeveloped sub-centers and prevalent low-level areas. ②Trends in ecosystem services varied, with water and soil conservation showing fluctuating increases, carbon sequestration remaining stable, and habitat quality declining. The integrated ecosystem services critically important zone is mainly located in the northeastern region and southwestern edge of the study area. ③Economic, social and ecological subsystems are highly coupled, with consistent overall development trends and strong interactions. ④The increase in the degree of harmonization amounted to 7.82%, with lagging subsystems varying in different degree of harmonization subregions. The study can provide a scientific basis for urban agglomerations to formulate scientific and reasonable development policies, promoting regional sustainable development and optimizing the spatial pattern of the national territory.

With the changes in the spatial structure of China's economic development, urban clusters have become the primary carriers of China's regional economy and green growth. The article uses annual data from 2010 to 2021 to study the carbon emission characteristics and carbon reduction pathways of 36 cities in the Yangtze River Delta region. Firstly, cities in the Yangtze River Delta region are divided into six carbon emission types based on decoupling elasticity coefficient and carbon intensity indicators. Then, the STIRPAT model is used to regress the panel data of different carbon emission types for 11 years, analyze the driving factors of carbon emissions, and develop differentiated carbon emission reduction paths for cities with six carbon emission types. According to the results, the city of Type I needs to accelerate low-carbon technology innovation, Type II needs to improve energy efficiency and strengthen low-carbon technology research and development, Type V needs to suppress foreign investment in high energy consumption and high emission projects in the local area, Type VI needs to accelerate the process of new urbanization and optimize industrial structure. Types III and IV have not received effective emission reduction paths, and further research is required on other emission reduction policies and measures.

Cabbage (Brassica oleracea L. var. capitata) plays a very important role in the annual national vegetable supply and export trade. In recent years, the cadmium content of agricultural soils has increased. As a result, cabbage yields and quality have declined significantly. Studies have shown that selenium can counteract the harmful effects of cadmium on plants and can alleviate the stress caused by cadmium during the growth of plants. However, the mechanism of exogenous selenium application in the alleviation of cadmium stress in cabbage seedlings has not been thoroughly investigated. In this study, exogenous selenium (10μMol/L) was applied under cadmium (25μMol/L) stress and the physiological mechanisms such as biomass, photosynthetic pigment, leaf stomata parameters, selenium and cadmium content, chloroplast ultrastructure, active oxygen accumulation, leaf membrane esterification and antioxidant enzyme activity were determined. The protective mechanism of exogenous selenium on cabbage seedlings under cadmium stress was investigated. The re-sults showed that exogenous application of selenium could effectively alleviate the decrease in growth, photosynthetic pigment and gas exchange characteristics of cabbage seedlings under cadmium stress, im-prove cabbage root vitality, reduce root leaf cadmium content and alleviate cadmium stress-induced damage. Ultrastructural observation showed that cadmium stress caused the disruption of the internal structure of chloroplasts of cabbage leaves, while exogenous selenium treatment alleviated the chloroplast damage to some extent, improved the stability of the inner capsule membrane and alleviated the cadmium stress-induced damage to photosynthetic organs. Cadmium stress also caused oxidative damage and ex-cessive accumulation of ROS in the leaves of cabbage seedlings as evidenced by significant accumulation of O2-, H2O2, MDA and electrolyte leakage. On the other hand, after exogenous selenium treatment, cadmium stress- induced oxidative damage could be reduced by up-regulating the activities of antioxidant enzymes SOD, POD and APX. At the same time, cadmium stress significantly increased GSH levels, and exogenous selenium treatment further increased GSH levels, thereby increasing the tolerance of cabbage to cadmium stress. In conclusion, by protecting the photosynthetic system, eliminating excessive accumulation of reactive oxygen species in cadmium-stressed cabbage seedlings, alleviating oxidative stress and reducing cadmium levels in the plant, exogenous selenium can further improve cadmium tolerance in cabbage seedlings.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

Currently, the chemistry of conjugated nitrodienes is becoming more and more popular. These molecules are successfully applied in cycloaddition to synthesize six-membered rings in Diels-Alder reactions. Nitrodienes can be also applied to obtain bis-compounds in [3+2] cycloaddition. Moreover, the presence of a nitro group in the structure provides a possibility of further modification of the products. The simplest symmetrical representative of conjugated nitrodienes is (1E,3E)-1,4-dinitro-1,3-butadiene. Although the first mentions of the compound date back to the early 1950s, the compound has not yet been examined thoroughly enough. Therefore, in this article a comprehensive study of (1E,3E)-1,4-dinitro-1,3-butadiene has been described. For this purpose, an experimental study including synthesis process as well as spectral characteristic has been conducted. So as to better understand the properties of this compound a computational study of reactivity indices based on MEDT and also assessment of pharmacokinetics and biological activity according to ADME and PASS methodologies have been made. On this basis, some future application trends of (1E,3E)-1,4-dinitro-1,3-butadiene have been proposed.

Abstract Objective Variations of sex characteristics (VSC) are atypical genetic, hormonal, gonadal and anatomical sex traits that require holistic medical management. The Chicago Consensus statement 2006 introduced the requirement that multidisciplinary teams organise the transition of care from pediatric to adult services. Yet, the evidence that the transitional care is in place is scarce. The aim of this paper is to examine the implementation of transition of care for people with VSC. Method Seven focus groups were conducted with health care professionals and peer support groups in care teams in Central, Northern and Western Europe. The data from the focus groups were examined using reflexive thematic analysis. Results The participants in the study stated that the transition of care has been implemented in the last two decades. The quality of care depends on available resources and variation of sex characteristics. However, there are significant hurdles to adequate transition of care as there is lack of time and resources. Lack of adult care providers and psychosocial support leaves young adults and adults with VSC navigating the health care system often alone. Conclusion The outcome of the study shows that the transition of care is organized through the department of pediatric endocrinology. The quality of care varies due to resources and variation. Lack of adult specialists and psychosocial support represent the biggest obstacle for young adults and adults to navigate the healthcare system and for the improvement in provision of healthcare to adults, especially psychosocial support.

With the rapid development of cities in northwest China, there has been an increasing focus on groundwater pollution in plateau cities, specifically the common occurrence of nitrate pollution. The special climatic, geological, and geomorphological characteristics of plateau and river valley cities contribute to distinct groundwater chemical characteristics. Therefore, the formation and evolution process of groundwater nitrate contamination differs from that of plain cities. To explore these issues, we conducted an analysis of eight major ions in various groups of water samples from rivers, springs, and groundwater in Haidong. By utilizing factor analysis and correlation analysis, we were able to identify the characteristics and formation of groundwater chemistry and nitrate pollution in Haidong. Our findings reveal that the chemical characteristics of groundwater in Haidong are primarily controlled by rock weathering, mineral dissolution, and evaporation, leading to the formation of highly mineralized groundwater. Additionally, the excessive nitrate content in certain areas is a result of domestic sewage discharge and agricultural fertilizer use, exceeding Chinese drinking water health standards. Furthermore, for cities located in valleys, the geological structure significantly impacts the nitrate content of groundwater in different regions. Areas with obstructed groundwater flow tend to have higher nitrate levels, while regions with unobstructed groundwater experience lower nitrate concentrations. Notably, shallow groundxwater is more vulnerable to nitrate pollution compared to deep groundwater. This study holds great significance in understanding the chemical characteristics of groundwater and the formation and evolution of nitrate pollution in highland river valley cities.

Reactive powder concrete (RPC) is a modern form of cementitious material. Major components include cement with a very low water-to-binder (w/b) ratio, steel fibres, superplasticizers, and very fine additives used in place of coarse aggregate, and very little water. The primary goal of this study is to examine the impact of immersion in sulfuric acid on compressive strength and to evaluate the impact of curing procedures on the preparation of RPC with high characteristics. The experimental work includes 4 mixes, which are prepared using 30 mm hooked-end steel fibers with a ratio of 0.4 by volume, silica fume and metakaolin with a ratio of 25% of cement weight. Compressive and indirect tensile strengths, ultrasonic velocity, and bulk density tests were conducted on the RPC that was prepared to evaluate its qualities. The results showed that heat curing resulted in a greater increase in strength than water curing did, and that mechanical properties improved with increasing SF more than MK additions. Heat-cured RPC demonstrated greater resistance to sulfuric acid immersion tests on compressive strength compared to water-cured RPC.

In recent years, the economies of many countries of the world are in a situation of intense shock processes. The current situation urgently needs to change the economic paradigm in the near future, which objectively requires the development of new conceptual models. The purpose of the paper is to develop the basic theoretical provisions of a new macroeconomics based on impulse and jump processes. Research problems are the following: 1) to describe the main types of impulse and jump functions with examples from economic theory and practice; 2) to perform an analytical representation of impulse and jump functions; 3) to select macroeconomic characteristics for the analysis of rapidly changing processes in the economy; 4) to create models and mechanisms for predicting impulsive and abrupt changes in macroeconomics. The approaches to the development of macroeconomic theory and its methods proposed in the article are not associated with the use of evolutionary continuous functions, for example, power functions, which is typical for many canonical macroeconomic models. These approaches do not include management decisions to achieve optimal values of given target functions, which is typical for recursive macroeconomic models of dynamic programming. This article is about formulating the foundations of macroeconomic theory and its methods, which, with some degree of accuracy, could give a forecast about the impending possibility of abrupt changes (impulse, shock, jump, stepwise and others) in the macroeconomic situation. The research methodology is statistical analysis, special methods for studying impulse and jump processes developed by the author. As a result of the study, the main provisions of the macroeconomic theory based on rapid impulse and spasmodic changes were formulated, approaches were outlined for constructing the tools of this theory, problems and tasks for further research were identified.

Olive orchards cover over 10 million hectares worldwide, with production techniques undergoing significant changes in the past three decades. The traditional rainfed approach, involving minimal inputs, has given way to irrigated super-intensive systems with higher planting density, in-creased productivity, greater use of fertilizers and phytopharmaceuticals, and total mechaniza-tion. Its impact on soil chemical properties remains a topic of great debate and no definitive consensus has been reached. Our main objective was to examine the different effects of traditional olive orchards and super-intensive ones on soil chemistry over a decade. We collected and ana-lyzed 1500 soil samples from an irrigation perimeter in southern Portugal in 2003 and 2013. Our findings indicate that compared to traditional olive orchards, super-intensive ones show, in a decade, a significant decrease in soil organic matter (less 22.8% - p<0.001) and an increase in so-dization (more 33.8% of Ext Na - p<0.001) highlighting the importance of monitoring this factor for soil fertility. In comparison to other irrigated crops in the region, super-intensive olive orchards promote a significant soil acidification (from 7.12 to 6.58), whereas the pH values of the other crops increase significantly (more 3.3%, 13.5%, 3.0% in corn, tomato and cereals, respectively). Mainly because organic matter levels decrease, soil acidification and soil sodization we can un-derline that hedgerow olive orchards can affect soil characteristics negatively when compared with traditional ones.

The functioning of forest ecosystems depends on the taxonomic and ecological diversity of soil fungi. Urbanization is increasing worldwide and is regarded a major driver of environmental change altering local species assemblages in urban forest. We investigated whether the degree of urbanization and local forest characteristics affect the soil fungal community in 20 beech forests located along a rural–urban gradient in the city of Basel and its suburbs (Switzerland). We analyzed their soil fungal communities by DNA metabarcoding of the rDNA ITS2 region and related these data to local forest vegetation characteristics and soil properties. The number of fungal OTUs in the 20 forests examined ranged from 170 to 303. Richness, diversity and evenness of fungal OTUs were all significantly affected by the degree of urbanization, but in different ways. OTU richness was highest in forests in areas with a low degree of urbanization and lowest in forests in rural areas. In contrast, the diversity of OTUs increased with increasing degree of urbanization. Different fungal phyla and fungal guilds showed distinct patterns in their relative abundance along the rural-urban gradient. The degree of urbanization reduced the relative abundance of symbiotrophic fungi, but increased that of saprotrophic and pathotrophic fungi. Our results show that urbanization alters soil fungal community, which in turn can lead to changes in forest ecosystems.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

In this paper, the main physicochemical characteristics and evolutionary laws of microbial community structure during the fermentation of aged vinegar were discussed, and the correlation between Cuqu and microorganisms and physicochemical characteristics during fermentation was explored. The results showed that there are significant differences in genera at different stages of fermentation, the main dominant bacteria in R1 are Bacillus, Lactobacillus, Aspergillus and Issatchenkia. At R2 fermentation stage, Lactobacillus, Acetobacter and Saccharomyces showed an upward trend and finally became absolute advantage bacteria. The main genus of bacteria at the end of overall fermentation is Aspergillus. Correlation analysis shows that in Cuqu, the bacterial genera that are significantly positively and negatively correlated with reducing sugars and amino acid nitrogen are the same, while the bacterial genera that are significantly positively and negatively correlated with pH and saccharification power are the same. During the fermentation process, pH, reducing sugar and saccharification ability are mainly positively correlated with bacterial genera. And research has found that during the fermentation process, the overall correlation between fungal communities and physicochemical characteristics is weaker compared to bacteria.

Due to the growth of tourism, mining and manufacturing, economy of the Hainan Island, southern China has swiftly expanded, but also poses a risk of soil pollution by mercury (Hg) due to the traffic and mineral processing. In order to investigate the characteristics of soil Hg pollution in the Hainan Island and assess the health risk, a total of 239 samples were gathered from five representative regions across the island. A vehicle-mounted potable mercury analyzer was used to measure the atmospheric Hg and soil Hg concentrations in the collected samples. The results indicate that the soil Hg concentration of the five sub-study areas exhibits notable fluctuations, which was found to be influenced by various factors, including wind direction, mining activities, and economic development conditions. The degree of Hg pollution was assessed using both the Single Pollution Index Method and the Geoaccumulation Index Method. The results showed that although nearly half of the sampling points were contaminated, the current soil Hg level does not pose a non-carcinogenic risk to human health.

A teoria diz que as primeiras coisas a existir no universo e no momento atual foram impulsionadas pela necessidade imperiosa; ou seja, os espaços físicos influenciam a existência de elementos e fatos a partir das inúmeras observações nos espaços físicos em relação a elementos e fatos. A existência de elementos obrigatórios no espaço é motivada pelas características dos espaços que oferecem condições para tal obrigação. A teoria afirma que o universo não surgiu por acaso; Ou seja, o universo surgiu por determinação influenciada pelo que o rodeia. O objetivo do estudo é ajudar a explicar os elementos e fatos do universo desde a origem até o presente.

Qinghai spruce (Picea crassifolia) is a ecologically important species in the forest ecosystem of the Qilian Mountains region in China. Natural regeneration of this species is critical to maintaining forest ecosystem function. We here analyzed several biological indicators among naturally re-generating Qinghai spruce across several elevations in the Pailugou watershed. Specifically, seedling density, basal diameter (BD), and plant height were measured, as were soil physico-chemical parameters, at 2700 m, 3000 m, and 3300 m above sea level. Differences in the biological indicators and correlations between the indicators and soil parameters were then assessed at each elevation. The results showed that soil stoichiometry was more sensitive to changes in el-evation than seedling indicators were. Furthermore, seedling density was positively correlated with soil pH, whereas BD was positively correlated with the carbon to nitrogen ratio (C/N), the carbon to phosphorus ratio, and soil organic carbon (SOC) contents. None of the analyzed soil parameters had a significant impact on elevation-specific differences in seedling density. However, soil pH, SOC, and C/N significantly affected variations in seedling diameter at each elevation. Finally, soil pH, SOC, C/N, and the carbon to phosphorus ratio significantly affected variations in seed-ling height at each elevation. This study provides a strong theoretical basis for further under-standing of the mechanisms associated with Qinghai spruce regeneration, ulti-mately contrib-uting to rational protection and management strategies for this important natural resource.

Yogurt ice cream (YIC) containing Bifidobacterum longum subsp. longum TISTR 2195 (B. longum) with different fat contents (2 and 10% fat) and prebiotics (galacto-oligosaccharide, GOS and fructo-oligosaccharide, FOS) was investigated for its physicochemical properties, microstructure, and survival of B. longum during storage time and in a simulated gastrointestinal tract. Fat contents affected pH, fat particle size, hardness, melting rate, and solid-like characteristic of ice cream while FOS seemed to enhance the hardness and elasticity of YIC better than GOS due to less solubility and denser microstructure which exhibited more solid-like properties than YIC containing GOS. The interaction effect of fat content at 10% fat and FOS in YIC seemed to promote more sensorial acceptance than the ice cream containing 2% fat and GOS. The fat content, concentration of prebiotics, and type of prebiotics were attributed to the survival of B. longum in YIC. Moreover, the survival number of B. longum in YIC during storage for 180 days and in the simulated gastrointestinal tract was still in 106 CFU g-1, which is considered to benefit human health. Finally, probiotic YIC in this study could be used as a guide for functional ice cream manufacture future.

The lactic acid bacteria Streptococcus thermophilus and Lactobacillus helveticus are commonly used as starter cultures in dairy product production. This study aimed to investigate the characteristics of fermented milk using different ratios of these strains and analyze the changes in volatile compounds during fermentation and storage. The 10:1 ratio of Streptococcus thermophilus CICC 6063 to Lactobacillus helveticus CICC 6064 showed optimal fermentation time (4.2 h), viable cell count (9.64 log10 colony-forming units/mL), and sensory evaluation score (79.1 points). In total, 56 volatile compounds were identified and quantified by solid-phase microextraction and gas chromatography–mass spectrometry (SPME-GC-MS), including aldehydes, ketones, acids, alcohols, esters, and others. Among these, acetaldehyde, 2,3-butanedione, 2,3-pentanedione, 2-heptanone, acetoin, and 1-heptanol had the highest odor activity values and contributed to the characteristic flavor of fermented milk. The concentrations and types of key flavor compounds reached their peak at the end of fermentation. Throughout the fermentation and storage process, the levels of 2,3-pentanedione and acetoin exhibited synergistic dynamics. These findings enhance our understanding of the chemical and molecular characteristics of milk fermented with Streptococcus thermophilus and Lactobacillus helveticus, providing a basis for improving the flavor and odor of dairy products during fermentation and storage.

This article is devoted to methods of processing random processes. Of particular relevance is the task of processing broadband non-stationary random processes. The processing of random processes is usually related to the assessment of their probabilistic characteristics. Very often, a non-stationary broadband random process is represented by a single implementation in a priori uncertainty about the type of distribution function. Such random processes occur in information and measuring communication systems in which information is transmitted at a real time pace (for example, radio telemetry systems of spacecraft). The use of methods of traditional mathematical statistics, for example, maximum likelihood methods to determine probability characteristics, in this case is not possible. The article discusses a method of processing non-stationary broadband random processes based on the use of non-parametric methods of decision theory. An algorithm for dividing the observation interval into stationary intervals using non-parametric Kendall statistics is considered, as well as methods for estimating probabilistic characteristics on the stationary interval using ordinal statistics. The article presents the results of statistical modeling using the Mathcad program.

Raindrop size distribution (RSD) is an index for reflecting precipitation characteristics. Analyzing the differences of RSD plays an important role in understanding the precipitation microphysical processes and improving quantitative precipitation prediction of radar. In this paper, the RSD data of Dafang (57708) station, Majang (57828) station, and Luodian (57916) station (with an altitude of 1722.7m, 985.0m, and 441.5m, respectively) in Guizhou are analyzed according to the precipitation microphysical characteristics. First,Particles with particle size less than 1mm contributes the highest value to the density of particle number , and decrease with the descending altitude. Second, the GAMMA distribution fit shows a better fit compare to M-P distribution fit, and GAMMA distribution fit increases with the ascending altitude. Third, the mass-weighted average diameter is not sensitive enough to the change of precipitation intensity with correlation coefficients of 54.84%, but there is a obvious relationship between the average volume diameter and the precipitation intensity with correlation coefficients of 69.15%. Then, the precipitation prediction model is established using LSTM neural network after fusing the representative microphysical characteristics of RSD with radar and rain gauge data. The precipitation prediction model is applied to the Dafang (57708) site to predict precipitation for time range of 0-180 minutes, and it is found that for the prediction of convective cloud and stratiform cloud precipitation, the 60-minute prediction results are the most consistent with the actual precipitation, where the correlation coefficients are 92.87% and 92.57%, respectively. Conclusively, the results demonstrate that combining with the RSD base data could improve the reliability of precipitation forecasting.

The layout of deep chamber for coal-gangue separation (DCCS) based on the horizon of the weak stratum can affect the stability of its surrounding rocks. First, the work summarized the main structural characteristics of DCCS. Similar simulation tests were performed to analyze the deformation and failure law of surrounding rocks of DCCS under different horizons of the weak stratum. Then, 60 numerical simulation schemes were designed by considering the lateral pressure coefficient and the thickness and horizon of the weak stratum. A comprehensive evaluation method was proposed for the stability of surrounding rocks. The optimal layout methods of the DCCS were determined based on the thickness and horizon of the weak stratum in different ground stress fields. If the thickness of the weak stratum was large and lateral pressure coefficient λ &lt; 0.6 or λ &gt; 1, the stability of surrounding rocks was optimal to arrange the side of DCCS along the weak stratum. When 0.6 ≤ λ ≤ 1, the optimal approach for controlling surrounding rocks was to position the floor of DCCS along the weak stratum. If the thickness of the weak stratum was small and λ&lt;0.6 or λ&gt;1, the stability of surrounding rocks was optimal to arrange the side of DCCS near roof along the weak stratum. When 0.6 ≤ λ ≤ 1, the optimal approach for controlling surrounding rocks was to arrange the side of DCCS near the floor along the weak stratum. The results can provide an important theoretical reference for the spatial layout and support design of DCCS.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Medical Self-service Terminals (MST) offer potential for process optimization and enhanced patient convenience in hospitals, including the elderly. However, the behavioral inclination (BI) of elderly Chinese individuals towards MST adoption remains suboptimal. This study aims to elucidate BI determinants for MST among the aging demographic, focusing on User Interface (UI) attributes within the extended Unified Technology Acceptance and Use Theory (UTAUT) Model. The empirical inquiry examines seven factors, comprising three key UI attributes and four fundamental UTAUT factors. Results reveal significant positive associations of Performance Expectancy (β=0.40, p&lt;0.001), Effort Expectancy (β=0.50, p&lt;0.001), and Social Influence (β=0.25, p&lt;0.05) with BI. Notably, User Interface Design positively correlates with Performance Expectancy (β=0.89, p&lt;0.001) and Effort Expectancy (β=0.81, p&lt;0.001). These findings emphasize the interplay between objective UI attributes and subjective UTAUT determinants. This research enhances understanding of UI's impact on MST BI and acceptance, particularly within the Chinese elderly population, urging MST researchers to prioritize elderly attitudes for effective technological integration in healthcare.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

Grazing exclusion (GE) and rest grazing (RG) are important management to restore grassland ecosystems. In order to evaluate the effects and mechanisms of different grazing management on species diversity, vegetation community indices and soil variables were determined in the plots of Qilian Mountains in Gansu Province. The results showed that diversity effects and their regulating mechanisms had space-scale dependence under different grazing management. Species richness and species diversity indices of RG in grassland were significantly higher than that of GE at the regional scale. Additionally, three grazing management in mountain meadows had only a significant effect on species richness, but different management in mountain meadows and temperate steppes had a significantly different effect on species diversity indices. Meanwhile, soil variables only influenced species diversity at the regional scale. Most of community and soil variables at each scale had positive effects on species diversity, except that the direction of biodiversity effects was negative for species coverage, mean plant height, soil porosity (SK) and bulk density (BD) under two contrasting grazing management. In conclusion, choosing RG at the regional scale and select grazing management according to different grassland types at the local scale to restore degraded grassland vegetation.

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

The globose scale (GS) (Sphaerolecanium prunastri Boyer de Fonscolombe) is a sucking insect that feeds on saps of wild apricot tree (Prunus armeniaca L.) in the Xinjiang Uygur Autonomous Region of northwestern China. It feeds on branches of wild apricot leading to poor growth, leaf yellowing and leaf drop, and sometimes mortality. Since the initial infestation in 2018, all the main valleys of wild apricot trees have been affected, but there is little research on the host’s physiological response to GS infestation. We measured the differences in growth between infested and non-infested wild apricots. The results showed that the diameter of shoot branches, the fresh weight, dry weight, length, width, area, and chlorophyll content of leaves, and the longitudinal diameter of fruit, were all significantly less for infested wild apricot trees than for un-infested wild apricot. The branch length of shoots, cross diameter, and weight of fruit also decreased, although the differences were not significant. Overall, GS infestation significantly reduced the growth of wild apricot trees, and may accelerate the damage by GS to wild apricot over time.

Vibro-fluidized dry coal beneficiation involves the unavoidable mixing of -1 mm coal dust into the fluidized bed, which compromises the stability and homogeneity of the bed density and reduces the effectiveness of fine-grained coal separation. In order to understand the features of coal powder separation and mixing (-1 mm) in a vibrating fluidized bed, as well as to achieve a uniform and stable bed density, a wide-grained dense medium consisting of -1 mm coal dust and 0.3-0.15 mm magnetite powder was homogeneously mixed in this work. The degree of density separation in the entire bed was examined, as well as the local mixing properties of the Wide-grained Dense Medium. It was discovered that when low vibrational energy was introduced at the same gas velocity, particle separation was enhanced in comparison to the usual fluidized bed. Little bubbles were found to ensnare fine coal dust and migrate upward, increasing density separation. The introduction of high vibrational energy leads to particle disorder within the bed and an increase in the level of particle mixing. The beneficial effects of vibration on the bed are diminished when the gas velocity is gradually increased under specified vibration circumstances. This causes big bubbles to develop more frequently, which increases particle mixing. Among them, the 1-0.5 mm fine-grained coal exhibits the best mixing state; it is less impacted by variations in air velocity and vibration levels, whereas the -0.5 mm coal dust is more affected by each of these variables. Furthermore, a wide range of air velocity regulation without a significant segregation state change was discovered to be achievable by the particle system under vibration circumstances of f=25Hz A=1mm and f=25Hz A=2mm.

Soil transverse isotropy results in different stiffness characteristics in the horizontal and vertical directions. However, the effect is usually neglected in the seismic motion analysis. In this study, an equivalent linear anisotropic soil model was established based on the finite element method and investigated the impact of anisotropic parameters on ground motion at the site under various seismic wave inputs. It is found that the anisotropic parameters have a more significant effect for the seismic waves with the dominant frequency closer to the fundamental frequency of the site. As an example, the soil dynamic parameters in Shanghai Yangshan Port were calibrated by a series of bending elements, resonance columns, and cyclic triaxial tests. The influences of anisotropy on the peak ground acceleration (PGA) and response spectrum are studied for Yangshan Port. Addi-tionally, the standard design response spectra considering the soil anisotropy were provided. A comparison reveals that the existing isotropic design response spectrum may lead to dangerous seismic design for the structures at Yangshan port.