Detailed kinetics for a 3-wavelength photopolymerization confinement (PC) system is presented for both numerical solutions and analytic formulas. The dynamic profiles are simulated for oxygen, free radical, and conversion for various situations of: blue-light only, 2-light (red and UV), and 3-light (red, blue, UV). An effective PC requires two conditions: (i) a strong N-inhibition for uncured regime with a low conversion (triggered by the UV-light); and (ii) a weak S-inhibition (oxygen-induced) for high conversion under the blue-light or blue and red-light initiation. Good PC candidates are governed by collective factors of: (i) the double ratio of light-intensity and initiator-concentration, (ii) monomers rate-constant; and (iii) effective absorption constants at specific wavelength and initiators. A new reverse feature for the role of N-inhibition on the blue-conversion is found. Higher oxygen concentration leads to a lower conversion, which could be enhanced by reducing the S-inhibition via a red or blue-light pre-irradiation, having a pre-irradiation time TP=200 s for red-light only, and reduced to 150 s, when both red and blue-light. System under UV-only leads a conversion lower than that of blue-only. However, conversion could be improved by the dual-light (blue and UV), and further enhanced by the pre-irradiation of red-light. The two competing factors, N-inhibition and S-inhibition, could be independently and selectively tailored to achieve: (a) high conversion of blue-light (without UV-light), enhanced by red-light pre-irradiation for minimal S-inhibition; and (b) efficient PC initiated by UV-light produced N-inhibition for reduced confinement thickness and for high print speed.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In EBM process monitoring, data analysis for processed layer quality evaluation is currently focused on the extraction of information from the raw data collected in-EBM process, i.e. thermal/ optical / electronic images, and the comparison between the collected data and the Computed Tomography (CT)/ microscopy images generated post-EBM process. This article postulates that a stack of bitmaps could be generated from the 3D model at a range of Z heights during file preparation of the EBM process, and serve as a reference image set. In-EBM process comparison between that and the workpiece images collected during the EBM process could then be used for quality assessment purposes. In addition, despite the extensive literature on 3D model slicing and contour generation for AM process preparation, no methods regarding image generation from cross sections of the 3D models have been disseminated in details. This article aims to address this by presenting a piece of 3D model-image generation software. The software is capable of generating binary 3D model reference images with user-defined Region-of-Interest (ROI) of the processing area, and Z heights of the model. It is envisaged that this 3D model-reference image generation ability opens up new opportunities in quality assessment for the in-process monitoring of the EBM process.

Cladding is typically used to protect components from wear and corrosion while also improving the aesthetic value and reliability of the substrate. The cladding process induces significant residual stresses due to the temperature difference between the substrate and the clad layer. However, these residual stresses could be effectively utilized by modifying processes and geometrical parameters. This paper introduces a novel methodology for using the weld-cladding process as a cost-effective alternative to various existing reinforcement techniques. The numerical analyses are performed to maximize the reinforcement of a cylindrical tool. The investigation of how the weld cladding develops compressive stresses on the specimen in response to a change in the weld beads and the welding sequence is presented. For the benchmark shape, experimental verification of the numerical model is performed. The impact of the distance between the weld beads and the effect of the tool diameter is numerically investigated. Furthermore, the variation in compressive stresses due to temperature fluctuations during the extrusion process has been evaluated. The results showed that adequate compressive stresses are generated on the welded parts through the cladding process after cooling. Hence, the targeted reinforcement of the substrate can be achieved by optimizing the welding sequence and process parameters.

The changes in consumer lifestyles have raised awareness of the variety of food options and packaging technologies. Active and smart packaging represents an innovative technology that serves to enhance the safety and quality of products. Smart packaging, as a subset of this technology, entails the integration of additives into packaging materials, thereby facilitating the preservation or extension of product quality and shelf life. This technological approach stimulates a heightened demand for safer food products with prolonged shelf life. Active packaging predominantly relies on the utilization of natural active substances. Therefore, the combination of active substances has a significant impact on the characteristics of active packaging particularly on polymeric blend like Polylactic acid (PLA) as a matrix. So, This review will summarize and explains how the addition of natural active agents influenced the properties related to the performance of active packaging through systematic analysis, providing new insights about the relationship between the types of active agents on physical-mechanical properties, bacterial colony reduction, and applications in foods packaging such as meat, fish, fruit, and vegetables. Through their integration, the market for active and smart packaging systems is expected to have a bright future.

Abstract: Interactions in multicomponent Ni-Cr-Mo-Al-Re model alloy were determined by ab initio calculations in order to investigate the Re doping effect on Haynes 282 alloy. Simulation results provided an understanding of short-range interactions in the alloy and successfully pre-dicted the formation of a Cr and Re-rich phase. The Haynes 282 + 3 % wt. Re alloy was manu-factured using the additive manufacturing Direct Metal Laser Sintering (DMLS) technique, in which the presence of the (Cr17Re6)C6 carbide was confirmed by an XRD study. The results ob-tained provide useful information about the interactions between Ni, Cr, Mo, Al, and Re as a function of temperature. The 5-element model designed can lead to a better understanding of phenomena that occur during the manufacturing or heat treatment of modern, complex, multi-component Ni-based superalloys.

If a lubricant contains structures capable of conducting energy, reactions involving zinc dialkyldithiophosphate (ZDDP) may take place both very close to and away from the solid surfaces, with this indicating that ZDDP can be a highly effective anti-wear (AW) additive. The central thesis of this article is that the tribocatalytic effect is observed only when the energy emitted by the solids is transmitted by ordered molecular structures present in the lubricant, e.g., graphene. The friction tests were carried out for 100Cr6 steel balls in a sliding contact with uncoated or a:C-H-coated HS6-5-2C steel discs in the presence of polyalphaolefin 8 (PAO 8) as the lubricant, which was enhanced with graphene and/or ZDDP. There is sufficient evidence of the interactions occurring between ZDDP and graphene and their effects on the tribological performance of the system. It was also found that the higher the concentration of zinc in the wear area, the lower the wear. This was probably due to the energy transfer resulting from the catalytic decomposition of ZDDP molecules. Graphene, playing the role of the catalyst, contributed to that energy transfer.

This study presents the manufacturing process driven development of an interlocking metasurface mechanism (ILM) for Fused Filament Fabrication (FFF) with a focus on open-source accessibility. The presented ILM is designed to enable strong contact between to planar surfaces. The mechanism consists of spring elements and locking pins which snap together when forced into contact. The mechanism is designed to optimize mechanical properties, functionality and printability with common FFF printers. The mechanisms is printed from thermoplastic polyurethane (TPU) filament which was selected for its flexibility, crucial for spring element performance and tolerances of the fabrication method. To characterize the designed mechanism a tensile test is carried out to assess the holding force of the ILM. The force-displacement profiles are analyzed and categorized into distinct phases, highlighting the interplay between spring deformation, sliding, and disengagement. The results show variations in holding forces attributed to geometric and material-related factors. The testing results are compared and discussed to a numerical simulation carried out with a frictionless approach with a nonlinear Neo–Hookean material law. The study underscores the importance of meticulous parameter control in 3D printing for consistent and reliable performance of interlocking metasurface mechanisms. The investigation leads to a scalable model of a ILM element pair with a distinct three-phase snapping characteristics ensuring reliable holding capabilities.

Selective Paste Intrusion (SPI) is an additive manufacturing (AM) process in which thin layers of aggregates are selectively bonded by cement paste only where the structure is to be produced. In this way, concrete elements with complex geometries and structures can be created. Reinforcement is required to increase the flexural strength of the concrete elements and, thus, enable their applicability in practice. Integrating the reinforcement is a difficult task, particularly in the case of SPI due to the layer-wise printing method. Especially with respect to possible complex structures, the production of the reinforcement needs to be adapted to SPI, thereby offering a high degree of freedom. One concept for a reinforcement integration is combining the two additive manufacturing processes SPI and Wire and Arc Additive Manufacturing (WAAM). However, since the two processes serve different fields of application, their compatibility is not necessarily given. Ongoing investigations show that the temperatures caused by WAAM adversely affect both, the cement paste rheology required for sufficient paste penetration into the particle bed and the overall concrete strength. This paper provides an overview of ongoing research focusing on different cooling strategies and their effects on the compressive strength of SPI-printed concrete parts.

Bone is a dynamic tissue with the capacity of repair and regeneration in specific conditions. Nevertheless, due to the increased incidence of bone disorders, the need of bone grafts has been growing over the past decades and the development of an ideal bone graft with optimal properties remains a clinical challenge. This review addresses the bone properties (morphology, composition and their repair and regeneration capacity) and puts the main focus on the potential strategies for developing bone repair and regeneration materials. It describes the requirements for designing a suitable scaffold material, types of materials (polymers, ceramics and composites) and techniques to obtain the porous structures (additive manufacturing techniques/robocasting or derived from marine skeletons) for bone tissue engineering applications. The main objective of this review is to gather the knowledge on the materials and methods for the production of scaffolds for bone tissue engineering and highlighting the potential of natural porous structures such as marine skeletons as promising alternative bone graft substitute materials without any further mineralogical changes, or after partial or total transformation into calcium phosphate. The suitability of the marine-derived porous bone graft substitutes for the intended applications will be also discussed.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

In the current paper, we present our work towards developing a solution combining computer vision and AI to support footrest design customization in the wheelchair industry. Wheelchairs and postural systems are complex and often user centric in the design process. Those products require a wide range of adjustments to adapt to the various anthropometries and disabilities of patients. Most commercial products, dedicated to severe disability, also include a series of additional elements, designed to keep the patient in a comfortable but “fixed” position. Such systems do not allow to “fix and maintain” the position of patient foot, especially for patients who have no control over their lower limbs. For that reason, it becomes essential to supply wheelchairs with specific elements to hold patient's shoe in place. Commercial foot supports are typically developed on standard sizes and do not always cover the entire population. In addition, those designs are based on standard shoes, thus they do not lend themselves well to adapting to special shoes or orthopedic shoes. Feet final position therefore becomes a key element in correct postural management. In this paper, we investigate the use of computer vision and AI to correctly define customization parameters of the footrest. The proposed design has been developed based on the specifications received from the Pro Medicare S.r.l orthopedic technicians. We present suitable algorithms, design principles and well defined components towards the implementation of our proof of concept. We also present the testing activities we have undertaken and the obtained performance results.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

The present work proposes a novel manufacturing technique based on the combination of Laser Metal Deposition, Laser Beam Machining and Laser Polishing processes for the complete manufacturing of complex parts. Therefore, the complete process is based on the application of a laser heat source both for the building of the preform shape of the part by additive manufacturing and for the finishing operations. Their combination enables to manufacture near-net-shape parts and afterwards, remove the excess material via laser machining, which has resulted to be capable of eliminating the waviness resulting from the additive process. Besides, surface quality is improved via laser polishing to reduce the roughness of the final part. Therefore, conventional machining operations are eliminated, what results in a much cleaner process. In order to validate the capability of this new approach, the dimensional accuracy and surface quality of the resulting parts are evaluated. The process has been validated on an Inconel 718 test part, where a previously additively built up part has been finished by means of laser machining and laser polishing.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

There is evidence that Additive Manufacturing plays a crucial role in the fourth industrial revolution. The design freedom provided by this technology is disrupting limits and rules from the past enabling engineers to have new products otherwise unfeasible. Recent developments in the field of SLM have led to a renewed interest in lattice structures that can be produced non-stochastically in previously unfeasible dimensional scales. One of the primary applications is aerospace engineering where the need of lightweight and performance is urgent to reduce the carbon footprint of civil transport around the globe. Of particular concern is fatigue strength. Being able to predict fatigue life in both LCF (Low Cycle Fatigue) and HCF (High Cycle Fatigue) is crucial for a safe and reliable design in aerospace systems and structures. In the present work, an experimental evaluation of compressive-compressive fatigue behavior has been performed to evaluate the fatigue curves of different cells, varying sizes and relative density. A Design of Experiment approach has been adopted in order to maximize the information extractable in a reliable form.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

Layer-wise 3D surface morphology information is critical for the quality monitoring and control of additive manufacturing (AM) processes. However, most of the existing 3D scan technologies are either contact or time consuming, which are not capable of obtaining the 3D surface morphology data in a real-time manner during the process. Therefore, the objective of this study is to achieve real-time 3D surface data acquisition in AM, which is achieved by a supervised deep learning-based image analysis approach. The key idea of this proposed method is to capture the correlation between 2D image and 3D point cloud, and then quantify this relationship by using a deep learning algorithm, namely, convolutional neural network (CNN). To validate the effectiveness and efficiency of the proposed method, both simulation and real-world case studies were performed. The results demonstrate that this method has strong potential to be applied for real-time surface morphology measurement in AM, as well as other advanced manufacturing processes.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

The current paper is focused on the rapidly developing field of nano-/micro three-dimensional production of inorganic materials. The fabrication method includes laserlithography of hybrid organic-inorganic materials with subsequent heat treatment lead-ing to a variety of crystalline phases in 3D structures. In this work, it was examineda series of organometallic polymer precursors with different silicon (Si) and zirconium (Zr) molar ratios, ranging from 9:1 to 5:5, prepared via sol-gel method. All mixtureswere examined for perspective used in 3D laser by manufacturing by fabricating nano-and micro-feature sized structures. Their deformation and surface morphology wereevaluated depending on chemical composition and crystallographic phase. The appear-ance of a crystalline phase was proven using single-crystal X-ray diffraction analysis,which revealed a lower crystallization temperature for microstructures compared tobulk materials. Fabricated 3D objects retain a complex geometry without any distortion after heat treatment up to 1400^oC. Under the proper conditions, a zircon phase (ZrSiO₄ - a highly stable material) can be observed. In addition, the highest newrecord of achieved resolution below 60 nm has been reached. The proposed prepara-tion protocol can be used to manufacture micro/nano-devices with high precision andresistance to high temperature and aggressive environment.

In this study, a novel task of printing speed optimization for continuous fiber composites is investigated. Using continuous fibers is an innovative approach to reinforce products made by fused filament fabrication (FFF) additive manufacturing (AM) technology. In the printing process of composites with continuous fibers, the printing speed is critical because of its significant effect on the geometric shape of the samples, especially their corners. During optimization in this research, continuous glass fiber (CGF) and polylactic acid (PLA) filaments were utilized as reinforcing phase and matrix, respectively, and were simultaneously fed into the extrusion-based polymer 3D printer to form PLA/CGF composites. The optimization was carried out by calculating the temperature changes of the deposited rasters in the presence and absence of fibers as a first step and then determining the special relationship between the printing speeds and rasters temperature changes. Finally, the optimal and the maximum printing speed was computed based on a hypothesis, which is proved by the results of high-quality printed composites with different geometric shapes.

The paper is focused on the examination of the internal quality of joints created in a multi-material - additive manufacturing process. The main part of the work focuses on experimental production and non-destructive testing of restrained joints of modified PLA (polylactic acid) and ABS (Acrylonitrile butadiene styrene) 3Dprinted on RepRap 3D device that works on the "open source" principle. The article presents the outcomes of non-destructive materials test in the form of the data from the Laser Amplified Ultrasonography, microscopic observations of the joints area and tensile tests of the specially designed samples. The samples with designed joints were additively manufactured of two materials: specially blended PLA (Market name – PLA Tough) and conventionally made ABS. The tests are mainly focused on the determination of the quality of material connection in the joints area. Based on the results obtained, the samples made of two materials were compared in the end to establish which produced material joint is stronger and have a lower amount of defects.

Binder jet printed components typically have low overall density in the green state and high shrinkage and deformation after heat treatment. It has previously been demonstrated that, by including nanoparticles of the same material in the binder, these properties can be improved as the nanoparticles can fill the interstices and pore throats between the bed particles. The beneficial effects from using these additive binder particles can be improved by maximising the binder particle size, enabling the space within the powder bed to be filled with a higher packing efficiency. The selection of maximum particle size for a binder requires detailed knowledge of the pores and pore throats between the powder bed particles. In this paper, a raindrop model is developed to determine the critical radius at which binder particles can pass between pores and penetrate the bed. The model is validated against helium pycnometry measurements and binder particle drop tests. It is found that the critical radius can be predicted, with acceptable accuracy, using a linear function of the mean and standard deviation of the particle radii. Percolation theory concepts have been employed in order to generalise the results for powder beds that have different mean particle sizes and size distributions. The results of this work can be employed to inform the selection of particle sizes required for binder formulations, to optimise density and reduce shrinkage in printed binder jet components.

It is a common practice to detect outliers in a financial time series in order to avoid the adverse effect of additive outliers. This paper investigated the performance of GARCH family models (sGARCH; gjrGARCH; iGARCH; TGARCH and NGARCH) in the presence of different sizes of outliers (small, medium and large) for different time series lengths (250, 500, 750, 1000, 1250 and 1500) using root mean square error (RMSE) and mean absolute error (MAE) to adjudge the models. In a simulation iteration of 1000 times in R environment using rugarch package, results revealed that for small size of outliers, irrespective of the length of time series, iGARCH dominated, for medium size of outliers, it was sGARCH and gjrGARCH that dominated irrespective of time series length, while for large size of outliers, irrespective of time series length, gjrGARCH dominated. The study further leveled that in the presence of additive outliers on time series analysis, both RMSE and MAE increased as the time series length increased.

This paper provides an overview of the new CPAM Project on Additive Manufacturing (AM) in design and simulation, focusing on topology & lattice structure optimization for a light-weighting advantage. This industry/academia collaboration project aims to utilize existing hardware and software tools, and investigate the practical limits of the technologies, providing eventual guidelines for general use. This will provide a solid foundation for the practical use of metal AM optimized solid and latticed structures especially for Ti6Al4V parts. Two case studies are demonstrated here, one a purely topology optimized design, and one also incorporating lattice optimized design, both from Ti6Al4V and load-bearing components, to be utilized in the Nelson Mandela University (NMU) Eco-Car Project in competition, late in 2018. This paper presents the Design for Additive Manufacturing (DfAM) process, the challenges met iro applying a DfAM design mindset, and a unique final voxel-based smoothing step finishing off the design process. Detailed structural integrity assessment of these parts are included - the question remains: can Additive Manufacturing help win the race?

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

(1) Background. Cognitive impairment in people with Multiple Sclerosis (MS) has been studied in relation to some clinical variables (e.g., motor disability and disease duration) and lifestyle fac-tors such as Cognitive Reserve (CR). However, only very few studies have considered the interac-tion of clinical variables and cognitive reserve in preserving the integrity of the neuropsychologi-cal profile. In this paper, we hypothesised that a higher level of CR might predict good cognitive efficiency by modulating the clinical outcome of the disease. (2) Methods. A sample of 100 partic-ipants with MS (age range 30-74), was recruited and assessed remotely with a questionnaire to measure CR and a cognitive screening test. Data were analysed through Generalized Additive Models. (3) Results. We found that the model analysing the interaction between CR and disease duration, and between CR and motor disability was able to explain a significant percentage of cognitive performance. In particular, higher levels of CR predicted better cognitive performance despite long disease duration, unless the motor disability was severe. (4) Conclusion. This study highlights the crucial role of CR in modulating cognitive efficiency in people with MS.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99±0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile strength in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile strength to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

Successive-addition-of-digits-of-a-number(SADN) refers to the process of adding up the digits of an integer number until a single digit is obtained. Concept of SADN has been occasionally identified but seldom employed in extensive mathematical applications. This paper discusses SADN and its properties in terms of addition, subtraction and multiplication. Further, the paper applies the multiplication-property of SADN to understand the distribution of prime numbers. For this purpose the paper introduces three series of numbers -S1, S3 and S5 series- into which all odd numbers can be placed, depending on their SADN and the rationale of such classification. Extending the analysis the paper explains how composite numbers of the S1 and S5 series can be derived. Based on this discussion it concludes that even as the concept of SADN is rather simple in its formulation and appears as an obvious truism but a profound analysis of the properties of SADN in terms of fundamental mathematical functions reveals that SADN holds a noteworthy position in number theory and may have significant implications for unfolding complex mathematical questions like understanding the distribution of prime numbers and Goldbach-problem.

The thermal stabilizers, lubricant, and plasticizers are three crucial additives for processing poly (vinyl chloride) (PVC). In this study, a new mannitol stearate ester-based aluminum alkoxides (MSE-Al) was designed and synthesized as a novel additive for PVC. The thermal stability and processing performance of PVC stabilized by MSE-Al were evaluated by Congo red test, conductivity measurement, thermal aging test, ultravioletevisible (UV-vis) spectroscopy test, and torque rheometer test. Results showed that the addition of MSE-Al can not only markedly improve the long-term thermal stability of PVC, but also greatly accelerate the plasticizing and decrease the balance torque which demonstrated that MSE-Al possesses the lubricating property. Thus, MSE-Al was demonstrated to be able to provide tri-functional additive roles, e.g., thermal stabilizer, plasticizer, and lubricant. The test results for the thermal stability of PVC indicated that the initial whiteness of PVC stabilized with MSE-Al was not good enough, thus the synergistic effect of MSE-Al with zinc stearates (ZnSt₂) on the thermal stability of PVC was also investigated. The results showed that there exhibited an appreciable synergistic effect between MSE-Al and ZnSt₂. The thermal stabilization mechanism and synergism effect of MSE-Al with ZnSt₂ were then discussed.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

Structural integrity is a crucial aspect of engineering components, particularly in the field of additive manufacturing (AM). Surface roughness is a vital parameter that significantly influences the structural integrity of additively manufactured parts. In this study, we present a comprehensive investigation into the relationship between surface roughness and structural integrity of Polyactic Acid (PLA) specimens produced through additive manufacturing. This research work focuses on the prediction of surface roughness of Additive Manufactured Polyactic Acid (PLA) specimens using eight different supervised machine learning regression-based algorithms. For the first time, Explainable AI techniques are employed to enhance the interpretability of the machine learning models. The eight algorithms used in this study are Support Vector Regression, Random Forest, XG Boost, Ada Boost, Catboost, Decision Tree, Extra Tree regressor, and Gradient Boosting regressor. The study analyzes the performance of these algorithms to predict the surface roughness of PLA specimens, while also investigating the impact of individual input parameters through Explainable AI methods. The experimental results indicate that the XG Boost algorithm outperforms the other algorithms with the highest coefficient of determination value of 0.9634. This value demonstrates that the XG Boost algorithm provides the most accurate predictions for surface roughness compared to other algorithms. The study also provides a comparative analysis of the performance of all the algorithms used in this study, along with insights derived from Explainable AI techniques.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Direct Energy Deposition (DED) is a versatile and efficient method in metal additive manufacturing. However, humping, caused by abnormal dynamics in the melt pool (MP), poses a significant threat to the geometric integrity of manufactured products. Current state-of-the-art (SOTA) methods primarily detect humping by analyzing late-stage spatial abnormalities, such as MP detachment. This approach is fundamentally reactive, leading to a tendency to miss early humping spatiotemporal dynamics, like cyclic elongation of the MP. This study introduces a novel, proactive indicator named VIMPS (Variability of Instantaneous MP Solidification-Front Speed), a physics-based tool designed to quantify early abnormal fluctuations in MP solidification speed. The experiments demonstrate VIMPS correlation with humping-induced geometric inaccuracies. By capturing early spatiotemporal dynamics of the MP, VIMPS reduces detection latency by 30 seconds compared to existing SOTAs that focus solely on spatial abnormalities. This significant improvement transforms detection from reactive to proactive, providing the time needed for corrective actions to enhance the overall productivity and quality of the DED process.

In recent years, Additive Manufacturing (AM), commonly referred to as 3D printing, has garnered the attention of the scientific community due to its capacity to transform ordinary and traditional items into customized materials at an affordable cost, through various AM processes. Antimicrobial/antibiofilm 3D printed materials are one of the most trending research topics, owing to the growing concerns over the emergence of complex microbial structures called "biofilms" on various surfaces. The review provides an overview of the evolution of additive manufacturing (AM) technologies and their various derivatives, along with a brief description of their materials and applications. It also introduces how biofilms can represent an advantageous lifestyle for microbial populations. The primary objective of this research was to conduct a systematic review on the development of planctonic or biofilm forms of microorganisms on 3D printed materials. The article summarizes commonly studied microorganisms on these materials and presents their 3D printing process, materials, as well as the fields covered by each of the analyzed papers. To the best of our knowledge, this is the first all-inclusive systematic review that amalgamated research conducted in diverse fields to assess the development of biofilms on surfaces produced through three-dimensional printing. Most notably, this review presents a comprehensive account of sustainable approaches for producing antimicrobial materials through 3D printing. Additionally, we assess their advancements in various fields such as medicine, environment, agri-food, and other relevant sectors. The findings of our literature review can be used to recommend appropriate microorganisms, 3D printing materials, and technologies for academic and industrial research purposes focusing on the development of microbial biofilms on 3D printed surfaces. Furthermore, it highlights the potential of environmentally-friendly modified AM technologies to combat biofilms in clinical and non-clinical areas. Our goal with this review is to help readers gain a better understanding of fundamental concepts, inspire new researchers, and provide valuable insights for future empirical studies focused on eradicating biofilms from 3D printed materials.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

This research focused on the perception of visually impaired individuals regarding tactile image creation using 3D printing. We developed and applied an experiment with 28 participants with visual impairments. They performed tasks based on skills whose foundations are needed and used in their daily lives, such as scanning, tactile discrimination, picture and spatial comprehension. The tactile images used in this study were developed by additive manufacturing and printed over 180 g/m² sulphite paper. The best performances were obtained when (1) the tactile image contour line heights were between 0.2 mm and 0.4 mm; and (2) the texture presented densities between 10% and 50%, when alone, or between 10% and 90%, when combined with another texture. The tested line widths (0.8 mm and 1.2 mm) did not present statistically significant differences in the results. Vision status (low vision or blindness) and moment of vision loss (congenital or late blind) did not influence the results. Schooling affected the activities of identifying objects and locating their copies. In the Conclusion section, there is a detailed recommendation list for the production and application of tactile materials, which range from simplifying forms to encouraging the use of both hands during content assimilation.

Additive Manufacturing and nanotechnology have been used as basic tools for the manufacture of nanostructured parts with magnetic properties to expand the variety of applications in additive processes by tank photopolymerization. Magnetic cobalt ferrite (CoFe2O4) and barium ferrite (BaFe12O19) nanoparticles with the size distribution of average value DTEM of 12 ± 2.95 nm and 37 ± 12.78 nm, respectively were generat-ed by hydroxide precipitation method. The dispersion of the nanoparticles on commercial resins (Anycubic Green and IRIX White resin) was obtained by mechanochemical reactions carried out in an agate mortar for 20 minutes, at room temperature and with limited exposure to light. The product of each reaction was placed in amber vials, also being kept in a box, to avoid contact with light. The photopolymerization process was carried out only at low concentrations (w/w % nanoparticles/resin) since, at high concentrations, there is no for-mation of pieces due to the high refractive index of ferrites. Raman shift spectroscopy of the final pieces showed that they contain the magnetic nanoparticles, with no apparent chemical changes. The EPR results of the pieces maintain the magnetic properties and apparently, they are not modified during the photopolymer-ization. Although significant differences were found in the dispersion process of the nanoparticles in each piece, we determined that the photopolymerization did not influence the structure and superparamagnetic behavior of ferrite nanoparticles during processing, and the magnetic properties were successfully transferred to the final 3D-printed magnetic obtained piece.

Nature provides plenty of good examples for simple and very efficient joint assemblies. One example is the enormously flexible cervical spine of American barn owls, which consists of 14 cervical vertebrae. Each pair of vertebrae produces a comparatively small individual movement in order to provide a large overall movement of the entire cervical spine. The biomimetic replication of such joints is difficult due to the delicate and geometric unrestricted joint shapes as well as the muscles that have to be mimicked. Using X-ray as well as micro computed tomography images and with the utilisation of additive manufacturing, it is possible to produce the owl neck vertebrae in scaled-up form, to analyse them and then to transfer them into technically usable joint assemblies. The muscle substitution of these joints is realised by smart materials actuators in the form of shape memory alloy wire actuators. This actuator technology is outstanding for its muscle-like movement and for its enormous energy density [1,2]. The disadvantage of this wire actuator technology is the low rate of contraction, which means that a large length of wire has to be installed to generate adequate movement. For this reason, the actuator wires are integrated into additively manufactured carrier components to mimic the biological joints. This results in joint designs that compensate for the disadvantages of the small contraction of the actuators by intelligently installing large wire lengths on comparatively small installation spaces, while also providing a sufficient force output. With the help of a test rig, the developed technical joint variants are examined and evaluated. This demonstrates the technical applicability of this bionic joints.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Additive manufacturing (AM) is a promising new technology that is having a very fast growth from home workshops to high-tech cutting-edge factories. As any manufacturing technique, adequate metrology services are needed to assure the quality of items manufactured by AM. One of the most widely used instruments to measure the characteristics of surfaces manufactured with AM is the confocal microscope. In this paper, authors present a whole calibration procedure for confocal microscopes designed to be implemented preferably in workshops or industrial environments rather than in research and development departments. Because of that, it is as simple as possible. The procedure is designed without forgetting any of the key aspects that need to be taken into account and based on classical reference material standards. These standards can be easily found in industrial dimensional laboratories and easily calibrated in accredited calibration laboratories.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

In this paper, the fatigue response of Fused Filament Fabrication (FFF) Acrylonitrile butadiene styrene (ABS) parts is studied. Different building parameters (layer height, nozzle diameter, infill density, and printing speed) were chosen to study their influence on the lifespan of cylindrical specimens according to a design of experiments (DOE) using the Taguchi methodology. The same DOE was applied on two different specimen sets using two different infill patterns: rectilinear and honeycomb. The results show that infill density is the most important parameter for both studied patterns. The specimens manufactured with the honeycomb pattern show longer lifespans. The best parameter set associated to that infill was chosen for a second experimental phase, in which the specimens were tested under different maximum bending stresses to construct the Wöhler curve associated to this 3D printing configuration. The results of this study are useful to design and manufacture ABS end-use parts that are expected to work under oscillating periodic loads.

Live fuel moisture content (LFMC) influences fire activity at landscape scale and fire behavior in laboratory experiments. However, field evidences linking LFMC to fire behavior are very limited despite numerous field experiments. In the present study, we reanalyze a shrubland fire dataset with a special focus on LFMC to explain this counterintuitive outcome. We found that this controversy might result from three reasons. First, the range of experimental LFMC data was too moist to reveal significant effect with the widespread exponential or power functions. Indeed, LFMC exhibited a strong effect below 100%, but marginal above this threshold, contrary to these functions. Second, we found that the LFMC significance was unlikely when the size of the dataset was smaller than 40. Finally, a complementary analysis suggested that 10 to 15% of random measurement error in variables could lead to an underestimation by 30 % of the LFMC effect. The effect of LFMC in field experiments is thus stronger than previously reported in the range prevailing during the actual French fire season and in accordance with observations at different scales. This highlights the need to improve our understanding of the relationship between LFMC and fire behavior to refine fire danger predictions.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

Natural rocks are highly heterogeneous due to various geological processes that constantly alter their properties. The accumulation, deposition, and cementation of mineral and organic particles continuously modify the spatial characteristics of rock properties. Property variability or anisotropy is commonly observed in most rock types and influences strength, transport, and thermal conductivity behavior. This unpredictability presents a significant challenge for laboratory testing. Binder-jet additive manufacturing (3D printing) has emerged as a valuable technology for characterizing rock properties in geoscience and engineering. This study proposes a methodology to evaluate the variability and repeatability of mechanical properties of 3D-printed sandstones during binder-jet additive manufacturing. The mechanical properties were analyzed statistically for samples located in various parts of the 3D printer build volume. The results showed that the 3D-printed sandstones exhibited significant variations in their strength and stiffness properties when measured from samples produced within the same build volume during binder-jet additive manufacturing. The Uniaxial Compressive Strength (UCS) varied from 23 to 38 MPa, with an average value of 29 MPa. The Young's modulus, on the other hand, ranged from 1.5 to 4.05 GPa, with an average value of 2.33 GPa. The variability of the mechanical properties, quantified by the standard deviation, decreased when the entire population of 3D-printed sandstones was divided into smaller samples situated at different elevations of the build platform.

In this research, a screw-barrel system was designed and implemented, coupled with material extrusion, to print high-melt-temperature thermoplastic materials. The aim was to integrate two methods: the direct extrusion of thermoplastic polymer pellets with material extrusion,utilize various polymers in the form of pellets, especially high melt temperature ones, instead of traditional filaments. This addresses one of the significant challenges in filament preparation for various materials that are not readily available in the market or nearly impossible to fabricate (such as highly filled plastics). First, the screw-barrel assembly performance and factors influencing feed rate were evaluated. Subsequently, specimens were printed with polyether ether ketone (PEEK), an advanced plastic material known for its outstanding mechanical properties, high-temperature tolerance, and broad applications in various sectors, such as medical. Additionally, the material was reinforced with 2.5% continuous glass fibers while printing, which presented a novel product. Upon comparing theoretical values with experimental data from the tensile testing, a notable observation emerged: the inclusion of 2.5% glass fibers led to an approximate 43% increase in the tensile strength of the material. Furthermore, SEM images provided visual evidence of satisfactory adhesion between layers and fibers.

In this work, the manufacture of thin walls with sharp corners has been optimized by adjusting the limits of a 3-axis cartesian kinematics through data recorded and analyzed off-line, such as axis speed, acceleration and the positioning of the X and Y axes. The study was carried out with two powder materials (SS316L and IN718) using the directed energy deposition process with laser. 1 mm thick walls were obtained with only one bead per layer and straight/sharp corners at 90º. After adjusting the in-position parameter G502 for positioning precision on the FAGOR 8070 CNC system, it has been possible to obtain walls with minimal accumulation of material in the corner, and with practically constant layer thickness and height, with a radii of internal curvature between 0.11 and 0.24 mm for two different precision configuration. The best results have been obtained by identifying the correct balance between the decrease in programmed speed and the precision in the positioning to reach the point defined as wall corner, with speed reductions of 29% for a programmed speed of 20 mm/s and 61% for a speed of 40 mm/s. The walls show minimal defects such as residual porosities, and the microstructure is adequate.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

This comprehensive review explores the advancements in Orthognathic and Oral Maxillofacial Surgery, focusing on the integration of 3D Printing and Virtual Surgical Planning (VSP). Traditional surgical methods, while effective, come with inherent risks and complications, and can lead to variability in outcomes due to the reliance on the surgeon's skill and experience. The shift towards patient-centric care necessitates personalized surgical methods, which can be achieved through advanced technology. The amalgamation of 3D printing and VSP revolutionizes surgical planning and implementation by providing tactile 3D models for visualization and planning, and accurately designed surgical guides for execution. This convergence of digital planning and physical modeling facilitates a more predictable, personalized, and precise surgical process. However, the adoption of these technologies presents challenges, including the need for extensive software training and the steep learning curve associated with computer-aided design programs. Despite these challenges, the integration of 3D printing and VSP paves the way for advanced patient care in orthognathic and oral maxillofacial surgery.

Hybrid manufacturing processes that combine additive and machining operations are gaining relevance in modern industry thanks to the capability of building complex parts with minimum material and, many times, with process time reduction. Besides, as the additive and subtractive operations are carried out in the same machine, without moving the part, dead times are reduced and higher accuracies are achieved. However, it is not clear whether the direct material deposition after the machining operation is possible or intermediate cleaning stages are required because of the possible presence of residual cutting fluids. Therefore, different LMD tests are performed on a part impregnated with cutting fluid, both directly and after the removal of the coolant by techniques such as laser vaporizing and air blasting. The present work studies the influence of the cutting fluid in the LMD process and the quality of the resulting part. Resulting porosity is evaluated and it is concluded that if the part surface is not properly clean after the machining operation, deficient clad quality can be obtained in the subsequent laser additive operation.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

The osseointegration process in and around additively manufactured (AM) lattice structures of a new titanium alloy, Ti–19Nb–14Zr, was evaluated. Three different implants, including lattices with increasing high sidewalls gradually closing them, were designed, manufactured and implanted in the tibia and metatarsal bone of two sheep for twelve weeks. After removal, they were characterized with X-ray computed tomography (XCT). The 3D XCT images were segmented using machine learning. The bone-interface implant (BII) and bone-implant contact (BIC) were studied. The results show that, since AM naturally leads to high roughness surface finish, the wettability of the implant is increased. The new alloy possesses an increased affinity to the bone enhancing the quality of osseointegration. The lattice provides crevices, in which the biological tissue can jump in and cling. The combination of these factors is pushing ossification beyond its natural limits. Therefore, the quality and speed of the ossification and osseointegration in and around these Ti–19Nb–14Zr AM laterally closed lattice implants open the possibility of bone spline key of prostheses. This enables the stabilization of the implant into the bone while keeping the possibility of punctual hooks allowing the implant to be removed more easily if required.

17-4PH steel is a widely used grade for precipitation hardening. The growing demand for modern materials with high corrosion and tribological resistance has led to its increased use for the production of medical devices. With additive manufacturing (AM), complex functional shapes can be achieved for medical applications. Direct laser metal sintering (DMLS) technology makes it possible to obtain products with complex architectures, but it also faces various challenges, including imperfections in the surface layer of products due to the use of 3D printing technology itself. This study analyzed the abrasive wear resistance in 0.9% NaCl solution of 17-4PH steel produced by DMLS technology. In order to improve the properties of the surface layer after 3D printing and to improve the tribological wear resistance of the steel, a shot peening (SP) process using CrNi shot and ceramic beads (based on ZrO2) was applied. The chemical and phase composition of the materials obtained, Vickers hardness, surface roughness, and microscopic and SEM imaging were investigated. Tribological tests were carried out using the ball-on-disc method, and the surfaces that showed traces of abrasion to identify wear mechanisms were subjected to SEM analysis. The chemical composition was in accordance with the EOS manufacturer's declarations, and the presence of austenite and martensite was found in the post-production state, while a higher content of martensitic phase was found in the case of peened samples due to phase transformations. The surface hardness of the peened samples increased more than twice, and the post-treatment roughness increased by 12.8% after peening CrNi steels and decreased by 7.8% after peening ZrO2 relative to reference surfaces. Roughness has an identifiable effect on sliding wear resistance. Higher roughness promotes material loss. After the SP process, the coefficient of friction increased by 15.5% and 20.7%, while the wear factor (K) decreased by 25.9% and 32.7% for the samples peened with CrNi steels and ZrO2, respectively. Abrasive and adhesive mechanism were dominant featured with slight fatigue. The investigation showed a positive effect of SP on the tribological properties of DMSL 17-4PH.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

Three-dimensional (3D) and four-dimensional (4D) printing emerged as the next generation of manufacturing techniques, spanning several research areas such as engineering, chemistry, biology, computing, and materials science. Three-dimensional printing allows the manufacture of complex shapes with high precision, by adding layer by layer of different materials. The use of smart materials that change shape or color, produce an electrical current, become bioactive, or perform an intended function in response to an external stimulus. Shape memory materials (SMMs) in 3D printing technology have attracted a lot of attention due to their ability to respond to external stimuli, leading this technology towards an emerging area of research, "4D printing technology." The core part of this review summarizes the effect of the main external stimuli on 4D textile materials followed by the main applications 4D printed textiles can change their shape over time due to external stimuli such as temperature.

(1) The study using the quails of the Manchurian golden breed was aimed at the efficacy of the food supplement based on micro-incapsulated phytase of Obessumbacterium proteus in the recombinant yeast producer Yarrowia lipolytica at a dose of 500 FYT/kg of the feed. (2) The effect of the supplement in the poultry diets on the productivity of young and adult quails was assayed; (3) It was found that the keeping the quails on the diets using the microencapsulated phytase O. proteus provided the highest live weight, the highest intensity of egg production, and the slaughter yield of animals, the lowest feed conversion compared to those in control groups and the groups getting a commercial phytase supplement based on Aspergillus ficuum. Taken together the data obtained in our experiments indicate a high degree of assimilation of phytate-containing products by the quails when using the encapsulated phytase compared to both the control and commercial preparation of phytase of the PhyA class. It can be concluded that it is a highly expedient and promising supplement based on the microencapsulated phytase of class D for feeding, which shows the best kinetic features compared to the phytases of PhyA and PhyC classes when working in the chyme of the poultry.

In this paper, the characterization of 3D printed materials that are considered in the design of multirotor unmanned aerial vehicles (UAVs) for specialised purposes was carried out. The multirotor UAV system is briefly described, primarily from the aspect of system dynamics, considering that the airframe parts connect the UAV components, including the propulsion configuration, into a functional assembly. Three additive manufacturing (AM) technologies were discussed, and a brief overview was given of selective laser sintering (SLS), fused deposition modeling (FDM), and continuous fiber fabrication (CFF). Using hardware and related software, 12 series of specimens were produced which were experimentally tested utilizing a quasi-static uniaxial tensile test. The results of the experimental tests are given graphically with displacement-force characteristics. In this work, the focus is on CFF technology and the testing of materials that will be used in the production of mechanically loaded airframe parts of multirotor UAVs. Furthermore, an overview was given in such a way that the specimens were grouped, and the mean values of the maximum stress were presented, so that the tested materials could be more easily compared with conventional materials, such as aluminum alloys.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

Additive manufacturing (AM) are used in several industries such as automotive, aerospace, and medical sciences. One of the most common devices used in additive manufacturing is fused deposition modeling (FDM) 3D printers. This fabrication method has different inputs that affect the quality of the parts. In this research, the bending fatigue properties of polylactic acid (PLA) biomaterial made with a 3D printer are investigated. To demonstrate the influence of printing parameters on fatigue lifetime, standard specimens with nozzle diameters of 0.2-0.6 mm, extruder temperature of 180-240°C, and print speed of 5-15 mm/s were printed. After performing fully-reversed bending fatigue tests, it was found that printed specimens at 180°C have the best fatigue lifetime in most cases. Accordingly, fatigue behavior improved by reducing the nozzle diameter. Printing at lower temperatures also improved fatigue lifetime. The printing speed affected the slope of the S-N diagram, known as the fatigue strength exponent.

Classification predictive modeling involves the accurate assignment of observations in a dataset to target classes or categories. There is an increasing growth of real-world classification problems with severely imbalanced class distributions. In this case, minority classes have much fewer observations to learn from than those from majority classes. Despite this sparsity, a minority class is often considered the more interesting class yet developing a scientific learning algorithm suitable for the observations presents countless challenges. In this article, we suggest a novel multi-class classification algorithm specialized to handle severely imbalanced classes based on the method we refer to as SAMME.C2. It blends the flexible mechanics of the boosting techniques from SAMME algorithm, a multi-class classifier, and Ada.C2 algorithm, a cost-sensitive binary classifier designed to address highly class imbalances. Not only do we provide the resulting algorithm but we also establish scientific and statistical formulation of our proposed SAMME.C2 algorithm. Through numerical experiments examining various degrees of classifier difficulty, we demonstrate consistent superior performance of our proposed model.

Welding processes offer a unique capability with a wide range of applications in industries. In recent times, welding has established itself as a tool for large scale additive manufacturing. In general, the quality and repeatability assurance for welding and specifically for additive manufacturing necessitates integrating process monitoring techniques with existing welding and additive manufacturing processes. The process-specific signals such as welding current fluctuations, temperature, and acoustic, generated during the welding operations, make them a suitable candidate for digitization. This chapter comprehensively describes the process monitoring techniques relevant to welding and additive manufacturing. Firstly, various sensors used during welding are described for their construction and working. Subsequently, specific applications of the sensors in digitizing the welding processes are presented.

Conditional generative adversarial networks (CGANs) learn a mapping from conditional input to observed image and perform tasks in image generation, manipulation and translation. In-situ monitoring uses sensors to obtain real-time information of additive manufacturing (AM) processes that relate to process stability and part quality. Understanding the correlations between process inputs and in-situ process signatures through machine learning can enable experimental-driven predictions of future process inputs. In this research, in-situ data obtained during a metallic powder bed fusion AM process is mapped with a CGAN. A single build of two turbine blades is monitored using EOSTATE Exposure OT, a near-infrared optical tomography system of the EOS M290 system. Layerwise images generated from the in-situ monitoring system were paired with a conditional image that labeled the specimen cross-section, laser-scan stripe overlap and z-distance to part surfaces. A CGAN was trained using the turbine blade data set and employed to generate new in-situ layerwise images for unseen conditional inputs.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Abstract: The broad clinical use of synthetic vascular grafts for vascular diseases is limited by their thrombogenicity and low patency rate, especially for vessels with a diameter inferior to 6 mm. Alternatives such as tissue-engineered blood grafts (TEBGs) have gained increasing interest. Among the different manufacturing approaches, 3D bioprinting presents numerous advantages and enables the fabrication of multi-scale, multi-material, and multicellular tissues with heterogeneous and functional intrinsic structures. Extrusion-, inkjet- and light-based 3D printing techniques have been used for the fabrication of TEBG out of hydrogels, cells, and/or solid polymers. This review discusses the state-of-the-art research on the use of 3D printing for TEBG with a focus on the biomaterials and deposition methods.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Laser metal deposition with wire (LMD-w) is a developing additive manufacturing (AM) technology that has a high deposition material rate and efficiency, and is suitable for fabrication of large aerospace components. However, control of material properties, geometry, and residual stresses is needed before LMD-w technology can be widely adopted for the construction of critical structural components. In this study, we investigated the effect of interlayer cooling time, clamp constraints, and tool path strategy on part distortion and residual stresses in large-scale laser additive manufactured Ti-6Al-4V components using finite element method (FEM). The simulations were validated with the temperature and the distortion measurements obtained from a real LMD-w process. We found that a shorter interlayer cooling time, full clamping constraints on the build plates, and a bidirectional tool path with 180⁰ rotation minimized part distortion and residual stresses and resulted in symmetric stress distribution.

The terrain of Changbai Mountain has great influence on the distribution of atmospheric flows and the occurrence and development of precipitation. This study quantitatively analyzes the regional characteristic of topographic perturbations and the relationship between terrain, wind and precipitation in Changbai Mountain region, by using a spectral analysis of the two-dimensional discrete cosine transform. Three domains with relatively heavy summer precipitation are selected as the study region. The results indicate that the overall terrain of Changbai Mountain region exhibits anisotropic characteristics. The terrain spectra of domain B are less than those of domain A and C across the whole wavelength (λ) bands, indicating that the large-scale topographic perturbations of domain B are relatively weak. The largest topographic spectral peak of domain C shows the most pronounced undulation of terrain among the three domains. The dominant wavelengths of terrain height variance for domain A and C, both close to the respective maximum wavelengths, indicate more prominent large-scale topographic perturbations. For domain A, the variation of the precipitation spectra is consistent with that of the wind spectra at the wavelength bands of λ < 390 km, showing a high correlation between wind field and the occurrence of rainfall. The inverse relationship at larger wavelengths indicates that multiple factors contribute to the occurrence of rainfall. For domain B, there is consistency in the fluctuations of terrain spectra, precipitation spectra, and wind spectra at the wavelength bands of λ < 278.3 km, implying that the smaller-scale terrain has an important effect on the occurrence of summer precipitation. For domain C, the variations of terrain spectra, precipitation spectra, and wind spectra are almost consistent across the whole wavelength bands, indicating that the large-scale terrain and minor terrain both play a crucial role in atmospheric uplift and the occurrence and development of summer rainfall.

HIV diagnosis and management have often caused disruptions to the everyday life and imagined futures of people living with HIV, both at individual and social levels. This has been conceptualised, in a rather dystopian way, as ‘biographical disruption’. This paper attempts to re-cast data from interviews with 40 men living with HIV (MLHIV) in Yogyakarta and Belu, Indonesia, in a slightly more positive light. Our analysis uses the concepts of additive and subtractive resilience strategies and we show how, rather than having a purely disrupted biography, participants talked about their experiences of ‘biographical reinvention'. Study participants were recruited using the snowball sampling technique, starting from two HIV clinics in the settings. Data were collected using one-on-one in-depth interviews, and a qualitative framework analysis was used to guide step-by-step data analysis. The findings showed that despite the disruptions in their everyday life (i.e., mental health condition, work, activities, social relationships, etc.) following the HIV diagnosis and management, MLHIV in our study managed to utilise their internal assets or traits (i.e., hope, optimism, resilience) and mobilised external resources (i.e., support from families, friends and healthcare professionals) to cope with the disruptions. An interweaving of these internal assets and external resources enabled them to take on new activities and roles (additive resilience strategies) and give up health compromising behaviours (subtractive resilience strategies). These were effective for most MLHIV in our study not only to cope with the HIV repercussions and improve their physical and mental health conditions, but to think or work on a ‘reinvented’ biography which encompassed resilience, hope and optimism for better health, life and future. The findings indicate the need for HIV interventions and healthcare systems that provide appropriate support for the development and maintenance of internal assets of PLHIV to enable them to cope with the repercussions of HIV and work on a ‘reinvented’ biography.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

The manuscript presents the use of three novel technologies for the implementation of wireless green battery-less sensors that can be used in agriculture. The three technologies, namely additive manufacturing, energy harvesting, and wireless power transfer from airborne transmitters carried from UAVs, are considered for smart agriculture applications. Additive manufacturing is exploited for the implementation of both RFID based sensors and passive sensors based on humidity sensitive materials. A number of energy-harvesting systems at UHF and ISM frequencies are presented which are in position to power platforms of wireless sensors, including humidity and temperature IC sensors used as agriculture sensors. Finally, in order to provide the wireless energy to the soil-based sensors with energy harvesting features, wireless power transfer (WPT) from UAV carried transmitters is utilized. The use of these novel technologies can facilitate the extensive use and exploitation of battery-less wireless sensors which are environmentally friendly and thus “green”. Additionally, it can potentially drive precision agriculture in the next era, through the implementation of a vast network of wireless green sensors which can collect and communicate data, to airborne readers so as to support with data the Artificial Intelligence and Machine Learning based, decision making platforms.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Additive manufacturing (AM) or 3D printing of metals is gaining popularity due to its flexibility in fabricating parts with highly complex designs, as well as simplifying manufacturing steps and optimizing process times. In this investigation, 17-4 PH stainless steel was additively manufactured using Laser-Powder Bed Fusion (L-PBF), followed by functionalization through a DUPLEX treatment. This treatment involved a plasma-assisted nitriding process, followed by deposition of an arc-PVD c-Al0.7Cr0.3N hard coating. The microstructural modifications resulting from plasma nitriding (such as the formation of Fe2,3N and Fe4N, and the αN or expanded martensite phases), and the surface improvements with the c-Al0.7Cr0.3N coating on the 3D-printed 17-4 PH steel, are evaluated in comparison to conventionally manufactured 17-4 PH steel. These microstructural characteristics are correlated with the mechanical response of the treated surfaces. As a result of the plasma nitriding process, the hardness of the 3D-printed 17-4 PH SS increased by approximately 260%. The wear, measured through dynamic and static scratch-testing, was reduced by approximately 31%. This improvement was attributed to the modification of adhesive failure mechanisms, leading to a reduction in wear volume, improved coating adhesion, and enhanced scratch resistance.

Human exposure to foodborne inorganic nanoparticles (NPs) is a growing concern. However, identifying potential hazards linked to NP ingestion often requires long-term exposure in animals. Owing these constraints, intestinal organoids are a promising alternative to in vivo experiments, as such an in vitro approach should enable rapid and reliable assessment of the effects on the gut of ingested chemicals. However, this remains to be validated for inorganic substances. In our study, a transcriptomic analysis and immunofluorescence staining were performed to compare the effects of food-grade TiO2 (fg-TiO2) on enteroid-derived monolayers (EDMs) from murine intestinal organoids to known impacts of TiO2 on intestinal epithelium. After validating their ability to dose-dependently respond to a pro-inflammatory cytokine cocktail, EDMs were exposed to 0.1, 1 or 10 µg fg-TiO2/mL for 24h. In line with known data, a dose-related increase of muc2, vilin 1 and chromogranin A gene markers of cell differentiation was observed. In addition, fg-TiO2 induced apoptosis and dose-dependent genotoxicity, while a decreased expression of genes encoding for antimicrobial peptides, and of genes related to tight junction function was observed. These results validated the use of EDMs as a reliable model for toxicity testing of foodborne NPs likely to affect the intestinal barrier.

This article addresses the need to know the thermal conductivity in different filaments that this FDM technology uses. Because there are multiple applications that these additive manufacturing products play in the field of thermal insulation. For the study of thermal conductivity, the DTC-25 commercial conductivity measurement bench is used, where the tests will be carried out on a set of seven different materials with 100% fabrication density. From base materials such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), materials of high mechanical and thermal resistance, polyether ether ketone (PEEK) and high-performance polyetherimide thermoplastic (ULTEM), to materials with metal inclusions (aluminum 6061) that would later be subjected to thermal aftertreatments. The study shows how the parts manufactured with aluminum inclusion have a higher thermal conductivity, 0.40 ±0.05 W/m·K, compared to another material, such as TPU, of high mechanical and thermal resistance, with a conductivity of 0.26 ±0.05 W/m·K.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

The Coronavirus disease 2019 (COVID-19) rapidly spread to over 180 countries and abruptly disrupted the production rates and supply chains worldwide. Since then, 3D printing also recognized as additive manufacturing (AM) and known to be a novel technique that uses layer-by-layer deposition of material to produce the intricate 3D geometry, has been engaged in reducing the distress caused by the outbreak. During the early stages of this pandemic, shortages of Personal Protection Equipment (PPE), including facemasks, shields, respirators, and other medical gears, were significantly answered by remotely 3D printing them. Amidst the growing testing requirements, the 3D printing emerged as a potential and fast solution manufacturing process to meet the production needs due to its flexibility, reliability, and rapid response capabilities. In the recent past, some of the other medical applications that have gained prominence in the scientific community include 3D printed ventilator splitters, device components, and patient-specific products. Regarding the non-medical applications, researchers have successfully developed contact-free devices to address the sanitary crisis in public places. This work aims to systematically review the applications of 3D printing or AM techniques that have been involved in producing various critical products essential to limit this deadly pandemic's progression.

Additive manufacturing (AM) is an emerged layer-by-layer manufacturing process. However, its broad adoption is still hindered by limited material options, different fabrication defects, and inconsistent part quality. Material extrusion (ME) is one of the most widely used AM technologies, and, hence, is adopted in this research. Low-cost metal ME is a new and AM technology used to fabricate metal composite parts using sintered metal infused filament material. Since the involved materials and process are relatively new, there is a need to investigate the dimensional accuracy of ME fabricated metal parts for real-world applications. Each step of the manufacturing process, from the material extrusion to sintering, might significantly affect the dimensional accuracy. This research provides a comprehensive analysis of dimensional changes of metal samples fabricated by the ME and sintering process, using statistical and machine learning algorithms. Machine learning (ML) methods can be used to assist researchers in sophisticated pre-manufacturing planning and product quality assessment and control. This study compares linear regression to neural networks in assessing and predicting the dimensional changes of ME made components after 3D printing and sintering process. The prediction outcomes using a neural network performed the best with the highest accuracy as compared to regression. The findings of this study can help researchers and engineers to predict the dimensional variations and optimize the printing and sintering process parameters to obtain high quality metal parts fabricated by the low-cost ME process.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

The noble metals palladium and silver find use in many high performance applications, and their alloys (PdAg), known for more than sixty years, are industrially important, finding use in many fields including hydrogen purification and separation, numerous facets of catalysis, and in fuel cells. In recent years, interest in these materials has grown significantly, particularly in energy generating applications and due to their performance as solid-state chemical sensors for a range of small molecules. PdAg thin films can be prepared using traditional physical methods such as cold rolling, or more modern and controllable chemical or physical deposition techniques such as electrodeposition or chemical vapour deposition. Despite the wide-reaching uses of PdAg, several recent advancements in materials preparation, such as additive manufacturing, better known as 3-D printing, remain unexplored for this material due to the differing chemistries of the two elements. In this review, we explore the manufacturing methods commonly employed for the preparation of PdAg thin films, the common and niche applications of these materials, and opportunities for the future development of these two aspects, with an emphasis on how preparation of thin films can utilise additive manufacturing approaches.

Notwithstanding the advances achieved in the last decades in the field of synthetic bone substitutes, the development of biodegradable 3D scaffolds with ideal mechanical and biological properties remains an unattained challenge. In this work, a novel approach is explored to produce synthetic bone grafts mimicking the complex bone structure using additive manufacturing. For the first time, scaffolds were produced, using an extrusion technique, composed of a thermoplastic polymer, polycaprolactone (PCL), hydroxyapatite nanoparticles (HANp), and polyethylene glycol diacrylate (PEGDA). These scaffolds were further compared with two groups of scaffolds: one composed of PCL and another of PCL and HANp. After production, optimisation and characterisation of these scaffolds, an in vitro evaluation was performed using human dental pulp stem/stromal cells (hDPSCs). Through the findings it was possible to conclude that PEGDA scaffolds were successfully produced presenting networks of interconnected channels, presenting hydrophilic properties (15.15 4.06°), adequate mechanical performance (10.41MPa 0.934), and allowing a cell viability significantly superior to the other groups analysed. To conclude, findings in this study demonstrated that PCL, HANp and PEGDA scaffolds may have promising effects on bone regeneration and might open new insights for 3D tissue substitutes.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.