Our investigations show that electrochemical corrosion of copper is faster than electrochemical corrosion of aluminium at temperatures below 100oC. Literature data analysis shows that the Al atoms diffuse faster than the Cu atoms at temperatures higher than 475oC, Al rich intermetallic compounds (IMCs) are formed faster in the Cu-Al system, and the Kirkendall plane shifts toward Al side. Electrochemical corrosion occurs due to electric current and due to diffusion. An electronic devise working time, for example, depends on initial copper cover thickness on aluminium wire, connected to the electronic devise, temperature, and volume and dislocation pipe diffusion coefficients, so copper, iron, and aluminium electrochemical corrosion rates are investigated experimentally at room temperature and at temperature 100oC. Intrinsic diffusivities ratios of copper and aluminium at different temperatures and diffusion activation energies in the Cu-Al system are calculated by proposed here methods using literature experimental data. Dislocation pipe and volume diffusion activation energies of pure iron are calculated separately by earlier proposed method using literature experimental data. Aluminium dissolved into NaCl solution as the Al3+ ions at room temperature and at temperature 100oC, iron dissolved into NaCl solution as the Fe2+ (not Fe3+) ions at room temperature and at temperature 100oC, copper dissolved into NaCl solution as the Cu+ ions at room temperature and as the Cu+ and the Cu2+ ions at temperature 100oC. It is founded experimentally that copper corrosion is higher than aluminium corrosion, and ratio of electrochemical corrosion rates, kCu/kAl>1, decreases with temperature increasing, although iron electrochemical corrosion rate doesn’t depend on temperature below 100oC. It is obvious, because melting point of iron is more higher then melting point of copper or aluminium. It is calculated that copper electrochemical corrosion rate is approximately equal to aluminium electrochemical corrosion at temperature about 300oC, so copper can dissolve into NaCl solution mostly as the Cu2+ ions at temperature about 300oC. Ratio of intrinsic diffusivities, DCu/DAl <1, increases with temperature increasing, and intrinsic diffusivity of aluminium could be approximately equal to intrinsic diffusivity of copper at temperature about 460oC.

Nanostructured anodic oxide layers on an FeAl₃ intermetallic alloy were prepared by two-step anodization in 20 wt.% H2SO4 at 0°C. The voltage range was 10.0 – 22.5 V with a step of 2.5 V. The structural and morphological characterizations of the received anodic oxide layers were performed by FE-SEM. Therefore, the formed anodic oxide was found to be highly porous with a high surface area, as indicated by the FE-SEM studies. It has been shown that the morphology of fabricated nanoporous oxide layers is strongly affected by the anodization potential. The oxide growth rate first increased slowly (from 0.010 μm/s for 10 V to 0.02 μm/s for 15 V) and then very rapidly (from 0.04 μm/s for 17.5 V up to 0.13 μm/s for 22.5 V). The same trend was observed for the change in the oxide thickness. Moreover, for all investigated anodizing voltages, the structural features of the anodic oxide layers, such as the pore diameter and interpore distance, increase with increasing anodizing potential. The obtained anodic oxide layer was identified as a crystalline FeAl₂O₄, Fe₂O₃ and Al₂O₃ oxide mixture.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

In order to develop waterborne silicate anticorrosive coatings to replace solvent-based anticorrosive coatings used widely in ship’s industry, epoxy modified silicate emulsions were synthesized with different content of epoxy resin, then aqueous silicate zinc-rich coatings were prepared with synthesized silicate emulsion, triethylamine and zinc powder. The influence of the content of epoxy on the properties and chemical structure of modified emulsion, mechanical properties of silicate coatings, and the corrosion behavior of silicate zinc-rich coatings in 3.5% NaCl solution were investigated. The coating samples on steel were measured by immersion test, Tafel polarization test and electrochemical impedance spectroscopy (EIS) test with different immersion time. The results showed that epoxy modified silicate emulsions were successfully synthesized. With the increase of epoxy content, the viscosity and the solid content of modified emulsion increases, the impact resistance of the silicate coating raises, the pencil hardness decreases, but the adhesion is not affected. Epoxy modification can reduce to s certain extent the corrosion driving force of zinc rich coating and increase the impedance of the zinc-rich coating decreases with the increase of immersion time in 3.5% NaCl solution. With the increase of the epoxy content, the resistance value of the zinc-rich coating increases, indicating the ability of the coating to resist corrosive media is enhanced.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

In the present work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated using three fused and crushed alumina powders of different particle size fine, medium and coarse. The influence of the particle size on thermal properties and micro-structural features of the produced coating were investigated by thermal insulation test and detailed image analysis technique, respectively. The analyzed micro-structural features include the total porosity, pore size (fine, medium, and large) and cracks. All types of cracks were considered in calculations as voids and were evaluated according to their sizes as pores. All spray parameters except the particle size were fixed throughout the spraying process. The results revealed that the fine starting powder has produced the densest coating with the lowest total porosity and that the total porosity increases with an increasing particle size. This was expected as powders of smaller particle size will reach a higher in-flight temperature and velocity than powders of bigger particle sizes as long as the same spray parameters are applied. However, a detailed image analysis investigation on the three produced coatings showed that the fraction of fine pores and cracks versus the total porosity is substantially higher in coatings produced by using fine starting powders than those produced using medium and coarse powders. In this work, a connection between the thermal insulation and the porosity fraction, which includes fine pores and cracks, was revealed.

The accumulation of microorganisms, plants, algae, or small animals on wet surfaces that have a mechanical function causes biofouling, which can result in structural or other functional deficiencies. The maritime shipping industry must constantly manage biofouling to optimize operational performance, which is a common and long-lasting problem. It can occur in any metal structure in contact or submerged in ocean water, which represents additional costs in terms of repairs and maintenance. This study is focused on the production of antifouling coatings, made with nanoparticles of copper selenide (CuSe) modified with gum arabic, within a water-base acrylic polymeric matrix. During the curing of the acrylic resin, the CuSe NPs remain embedded in the resin but this does not prevent the release of ions. The coatings presented to release copper and selenium ions for up to 80 days, selenium was the element that was released the most. The adhesion of film coatings to metallic substrates showed good adhesion, scale 5B (ASTM D3359 standard). Antimicrobial activity tests show that the coatings have an inhibitory effect on Escherichia coli and Candida albicans. The effect being more noticeable when the coating is detached from the substrate and placed on a growing medium, than compared to the coating on a substrate. Scanning electron microscopy (SEM) observations show that nanostructured CuSe coatings are made up of rod-shaped and spherical particles whose range ranges from 12 to 25 nm. The Energy Dispersive X-ray spectroscopy (EDS) studies showed that the ratio of selenium nanoparticles is greater than that of copper and that their distribution is homogeneous

Master equations define the dynamics that govern the time evolution of various physical processes on lattices. In the continuum limit, master equations lead to Fokker-Planck partial differential equations that represent the dynamics of physical systems in continuous spaces. Over the last few decades, nonlinear Fokker-Planck equations have become very popular in condensed matter physics and in statistical physics. Numerical solutions of these equations require the use of discretization schemes. However, the discrete evolution equation obtained by the discretization of a Fokker-Planck partial differential equation depends on the specific discretization scheme. In general, the discretized form is different from the master equation that has generated the respective Fokker-Planck equation in the continuum limit. Therefore, the knowledge of the master equation associated with a given Fokker-Planck equation is extremely important for the correct numerical integration of the latter, since it provides a unique, physically motivated discretization scheme. This paper shows that the Kinetic Interaction Principle (KIP) that governs the particle kinetics of many body systems, introduced in [G. Kaniadakis, Physica A 296, 405 (2001)], univocally defines a very simple master equation that in the continuum limit yields the nonlinear Fokker-Planck equation in its most general form.

Several coatings configurations of combined aluminizing and diffusion layered aluminide on 316 steel were produced and characterized. These coatings, typically employed as thermal barrier coating (TBC), can also be effective as vibration reduction elements at intermediate and high temperatures. This preliminary work has been focused on the microstructural design and processing effects of the coatings. The damping of the produced specimens was measured up to 450°C and compared with that of the steel substrate. The most performing coatings contain an Al-Si layer and exhibit a steep damping increase above 200 °C, reasonably due to dislocation movements by plastic straining of soft alloy layer and to the interface sliding between layers with different elastic moduli.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

One method of creating a brass coating is through electrodeposition, which is most often completed in cyanide galvanic baths. Because of the toxicity of cyanides, many are working on the development of cyanide-free baths, which are promising but not satisfactory to replace the classic methods. The purpose of the study was to explore a new generation of non-aqueous cyanide-free baths based on 1-ethyl-3-methylimidazolium acetate ionic liquids. The study involved the formation of copper, zinc, and brass coatings. The influence of the bath composition, cathodic current density, and temperature was determined. The obtained coatings were characterized by their morphology, chemical composition, roughness, and corrosion resistance. It was found that the structure of the obtained coatings is strongly dependent on the process parameters. The three main structures observed were fine-grained, porous, and olive-like. To the best knowledge of the authors, it is the first time the olive-like structure was observed in the case of an electrodeposited coating. The Cu-Zn coatings consisted of 19–96 at.% copper and exhibited relatively strong corrosion resistance. High improvement of corrosion properties was found in the case of copper and brass coatings with an olive-like structure.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

In laser joining of copper (Cu) and aluminum (Al) sheets, the Al sheet is widely chosen as the top surface for laser irradiation because of increased absorption of laser beam and lower melting temperature of Al in contrast to Cu. This research focus on welding from Cu side to Al sheet. The main objective of irradiating the laser beam from the copper side (Cu on top) is to exploit higher solubility of Al in Cu. A significantly lower laser power can be used with 515 nm laser in comparison to 1030 nm. In addition to low laser power, a stable welding is obtained with 515 nm. Because of this advantage, 515 nm is selected for the current research. By fusion of Cu and Al the two sheet metals are welded, with presence of beneficial Cu solid solution phase and Al+Al2Cu in the joint with the brittle phases intermixed between the ductile phase. Therefore the mixed composition strengthens the joint. However excessive mixing leads to formation of more detrimental phases and less ductile phases. Therefore optimum mixing must be maintained. Energy dispersive X-ray spectroscopy (EDS) analysis indicate that large amount of beneficial Cu solid solution and Al rich phases is formed in the strong joint. From the tensile shear test for a strong joint, fracture is obtained on the heat-affected zone (HAZ) of Al. Therefore the key for welding from copper side is to have optimum melt with beneficial phases like Cu and Al+ Al2Cu and the detrimental phases intermixed between the ductile phases

Food processing and consumption involves multiple contacts between biological fluids and solid materials of processing devices of which steel is one of the most common. Due to complexity of these interactions, it is difficult to identify the main control factors in the formation of undesirable deposits on the device surfaces that may affect safety and efficiency of the processes. Mechanistic understanding of biomolecule-metal interactions involving food proteins could improve management of these pertinent industrial processes and consumer safety in food industry and beyond. In this work, we perform a multiscale study of formation of protein corona on iron surfaces and nanoparticles in contact with cow milk proteins. By calculating the binding energies of proteins with the substrate we quantify the adsorption strength and rank proteins by the adsorption affinity. We use a multiscale method involving all-atom and coarse-grained simulations as well as generation of 3D structures of the proteins for this purpose. Finally, using the adsorption energy results, we predict the composition of protein corona on iron nanoparticles and flat surfaces via a competitive adsorption model.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

We consider a specific holographic model in the limit where the gauge field does not couple to the rest of of the holographic fields (gravity and scalar sector) and investigate a phase of matter at zero charge density, a realistic feature that may have implications for disordered strange metals. We then pick a specific form of the gauge coupling $Z(\alpha)$ with a certain disorder realization and argue that this provides a hard-gapped insulator with exponentially-suppressed conductivity by holographic methods. The limit is non-trivial: as there is backreaction at zero density amount, surviving in the coupled case.

Information taken from David A. Scott’s book “Copper and Bronze in Art” was crucial for research on copper corrosion products in Stuttgart. Examples discussed are the nature and variability of ‘Black Spots’ (aka ‘Brown Fuzzies’); cupric hydroxide by cleaning, patination, and pigment synthesis; the wondrous phenomenon of curly malachite; chalconatronite formed by contact to soda glass; the formation of copper formates by glass-induced metal corrosion; and synthesis and X-ray diffraction of basic copper acetates (‘verdigris’).

Polymer electrolyte was used as a medium for testing the performance of microband electrodes under conditions of linear diffusion. Cyclic voltammetry and chronoamperometry experiments were performed in such viscous medium, where diffusion rates are much slower than in fluid solutions. Confirmation of the existence of such conditions from the log i vs. log v or log i vs. log t relationships in the current equation always yielded values lower than the expected value of 0.5. This could indicate impure linear diffusion profile, i. e. some contribution from radial diffusion (edge effect). However, performing these tests in monomeric solvents of similar viscosities, such as glycerol or propylene glycol, gave the desired value of 0.5. These results lead to the conclusion that current equations which are based on Fick’s laws may not be applicable for polymer electrolytes, where various obstruction to diffusion make it a more complicated process than in monomeric solvents.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Selection of efficient corrosion inhibitors requires detailed knowledge regarding interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. Position of functional groups between different isomers is often overlooked but not less important since factors like steric hinderance may significantly affect the adsorption mechanism. In this study we have presented how different dihydroxybenzene isomers interact with aluminium alloy 5754 surface, reducing its corrosion rate in bicarbonate buffer (pH = 11). We have shown the highest inhibition efficiency among tested compounds belongs to catechol at 10 mM concentration, although differences were moderate. Utilization of novel impedance approach to adsorption isotherm determination allowed to confirm that while resorcinol chemisorbs on aluminium surface, catechol and quinol follows ligand exchange model of adsorption. Unlike catechol and quinol, the protection mechanism of resorcinol is bound to interaction with insoluble aluminium corrosion products layer and was only found efficient at concentration of 100 mM (98.7%). The aforementioned studies were confirmed with scanning electron microscopy and x-ray photoelectron spectroscopy analyses. There is a significant increase of the corrosion resistance offered by catechol at 10 mM after 24 h exposure in electrolyte: from 63 to 98%, with only negligible changes in inhibitor efficiency observed for resorcinol at the same time. However, in the case of resorcinol a change in electrolyte color was observed. We have revealed that the differentiating factor is the keto-enol tautomerism. The NMR studies of resorcinol indicate the keto form in structure in presence of NaOH, while the chemical structure of catechol does not change significantly in alkaline environment.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

A 9,10-phenanthrenequinone (PQ) was electrochemically polymerized on a graphite rod electrode using potential cycling. The electrode modified by poly-9,10-phenanthrenequinone (poly-PQ) was studied by means of cyclic voltammetry, electrochemical impedance spectroscopy, atomic force microscopy and scanning electron microscopy. The poly-PQ shows variations in growth pattern depending on the number of potential cycles for the initiation of polymerization. Formed poly-PQ layer demonstrates good electric conductivity, great electrochemical capacitance and unique oxidation/reduction properties, which are suitable for broad technological applications, including applicability in biosensors, supercapacitors, and in some other electrochemical systems.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

This paper investigates the effect of shot peening on the strength and corrosion properties of EN AW 6082-T651 aluminium alloy. Surface roughness, microhardness, residual stresses and corrosion performance were investigated and compared with the untreated aluminium alloy. Cracks and delaminations in the surface layer can only be seen on the treated specimens at a working pressure of 4 bar and 8 bar, while no such effect was observed at a working pressure of 1.6 bar. The effect of dislocation densification was confirmed by the microhardness measurement of the hardened layer, where microhardness increased by up to 23 % compared to the untreated aluminium alloy. Shot peening also results in a deeper layer with higher compressive residual stresses compared to untreated specimens. With higher working pressure, surface roughness increases, which can promote localized pitting corrosion. However, all treated specimens improve the corrosion resistance and have a lower degree of anodic dissolution. The current density of the shot peened specimen with the lowest surface roughness was more than twice lower than that of the untreated specimen.

In this work, nitrite intercalated CaAl-LDH was firstly prepared in this work. Scanning electronic microscopy (SEM) coupled with the energy dispersive spectrometer (EDS) was used to characterize the morphology and element composition of the synthesized powder. Fourier transform infrared spectroscopy (FTIR) was used to characterize the chemical composition and X-ray diffraction (XRD) was used to analyze the structure. The nitrite release curve and the chloride concentration change curve were obtained to study the anion-exchange reaction. The corrosion protection effect of the CaAl-LDH loaded with nitrites towards the carbon steel was evaluated in 0.02 M NaCl solution by electrochemical impedance spectroscopy (EIS). Then the powder was added in the epoxy coating with a percentage of 2% (vs. epoxy resin). The coating morphology and roughness was evaluated by SEM and laser microscopy, and the corrosion protection effect was investigated by EIS in an immersion period of 21 d. Local electrochemical impedance spectra (LEIS) was used to characterize the corrosion development process in micro-corrosion sites. The corrosion product of the scratched area after salt spray exposure was analyzed by EDS and Raman spectroscopy. The corrosion protection mechanism of the CaAl-LDH loaded with nitrites was proposed based on the above experimental results.

Carbonous nanomaterials are promising additives for composite coatings for heat-dissipation materials because of their excellent thermal conductivity. Here, copper/carbonous nanomaterial composite coatings were prepared using nanodiamond (ND) as the carbonous nanomaterial. The copper/ND composite coatings were electrically deposited onto copper substrates from a continuously stirred copper sulfate coating bath containing NDs. NDs were dispersed by ultrasonic treatment, and the initial bath pH was adjusted by adding sodium hydroxide solution or sulfuric acid solution before electrodeposition. The effects of various coating conditions—the initial ND concentration, initial bath pH, stirring speed, electrical current density, and the amount of electricity—on the ND content of the coatings were investigated. Furthermore, the surface of the NDs was modified by hydrothermal treatment to improve ND incorporation. A higher initial ND concentration and a higher stirring speed increased the ND content of the coatings, whereas a higher initial bath pH and a greater amount of electricity decreased it. The electrical current density showed a minimum ND content at approximately 5 A/dm². Hydrothermal treatment, which introduced carboxyl groups onto the ND surface, improved the ND content of the coatings. A copper/ND composite coating with a maximum of 3.85 mass% ND was obtained.

The kinetic analysis of octogen coating with a polyurethane base containing hydroxyl-terminated polybutadi-ene (HTPB) was investigated using infrared spectroscopy. The coating process involved a solvent method, where octogen and liquid polyurethane were mixed, the solvent was evaporated, and curing took place at an elevated temperature. The ratio of HTPB to diisocyanate was equimolar. Initially, the curing process occurred in the solvent system, followed by further curing in the bulk system. The kinetic analysis was performed using a modified diffusion-autocatalytic model, which includes non-catalytic, autocatalytic, and diffusion compo-nents. This model was compared with others during the bulk reaction and proved to be effective in correcting errors, particularly in the gel time region. Thermodynamic parameters were evaluated using the Arrhenius and Eyring equations. The reaction rate was initially controlled by chemical reactivity, but after the gel time, diffusion became the controlling factor. In the HTPB-TDI system, both the non-catalytic and autocatalytic parts decreased with increasing temperature, while diffusivity increased. It is worth noting that diffusivity is temperature-dependent. Different diisocyanates, namely toluene diisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HMDI), were studied, revealing that HMDI exhibited higher reactivi-ty than TDI and IPDI. The catalyst effect on reaction rate HTPB-TDI system is investigated. Catalysts adding (0.1%) to HTPB-TDI system is really decrease their activation energy by efectivity DBTL>FeAA>TPB. Catalyst not change their diffusivity.

Porous metals possess low bulk density, large specific strength, high stiffness and special thermal, electromagnetic and acoustic conductivity, so that porous metals are widely used in filtration and separation, flame retardant explosion-proof, biomedical application, etc. Compared with its corresponding dense metal, the presence of porous structures also leads to different corrosive performances of porous metal. So, some researches have utilized weight loss method, electrochemical impedance to evaluate porous metals’ corrosion behavior; however, the influence of pore structure on metal corrosion is still controversial, and present methods used for analyses of porous metals’ corrosion are statistical averages of the corrosion behavior of the entire porous material, which cannot accurately reflect the corrosion behavior inside the pore structure. Herein, we prepare porous copper samples with 0, 24, 72, 96 pores using mechanical process, and employ scanning kelvin probe combined with electrochemical polarization curve and impedance spectroscopy to test the corrosion performance of the porous copper in static and dynamic NaCl solution. The relevant results indicate that in static solution, the corrosion resistance of samples gradually increases with the rise of the number of pores. By contrast, the sample with 24 pores exhibits more susceptible to corrosion than the sample without pore.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Diatomite (DME) consists of natural ordered porous structures that are excellent candidates as microcontainers. However, to the best of our knowledge, the application of DME loaded with corrosion inhibitors in anti-corrosion coatings has not hitherto been reported. In this study, DME has been used as a source of microcontainers to load benzotriazole (BTA) inhibitor by an immersion method. In order to prevent unwanted early release of the small molecule BTA inhibitor from the DME microcontainers, inspired by the adhesion characteristics of catechol and amine in mussel adhesion protein, polydopamine (PDA) was coated on their surfaces to generate BTA@DME/PDA microcapsules. Because of the depolymerization characteristics of PDA at low pH, the synthesize microcapsules showed a controllable release function. The SEM morphology, chemical structure, and loading capacity of the synthesized BTA@DME/PDA microcapsules were characterized. The corrosion resistances of epoxy coatings with different contents of BTA@DME/PDA microcapsules were compared by saline immersion and electrochemical impedance tests. A scratched coating with 5wt.% BTA@DME/PDA microcapsules showed the best anti-corrosion effect.

The release profiles of methotrexate, an anticancer drug, from the monoolein liquid crystalline cubic phases were studied. The cubic phases were used either in the form of a lipidic film deposited onto a glassy carbon electrode surface or in the dispersed form of magnetocubosomes, which are considered a prospective hybrid drug delivery system. Commonly, cubosomes or liposomes are employed, but not in the case of toxic methotrexate, known to block receptors responsible for folate transport into the cells. The release profiles of the drug from the lipidic films were monitored electrochemically and described using the Higuchi model. They were also modified via changes in temperature; the release was faster, although deviating from the model when the temperature was increased. Magnetocubosomes - cubic phase nanoparticles containing hydrophobic magnetic nanoparticles placed in an alternating magnetic field of low frequency and amplitude, stimulated drug release from the suspension, which was monitored spectroscopically. These new biocompatible hybrid materials are very promising, allowing to control the release of the drug at the appropriate sites, but do require further investigations into their in vitro cytotoxicity and in vivo biodistribution.

In this paper, various Ni-P composite coatings containing toner, MoS2, and nano-SiO2 particles were deposited on steel substrates by the electroless method. Then, the electrochemical properties of these coatings after a heat treatment process were compared. The microstructural evaluations were also done by using the optical and electron microscopy methods. Both Tafel polarization and electrochemical impedance spectroscopy techniques were utilized to survey the electrochemical behavior of such coatings. The surface morphology of all coatings contained cauliflower-like nodules. The X-ray diffraction patterns showed the crystalline phases of Ni and Ni3P for all coatings after the heat-treatment step. Obtained results showed that all composite coatings exhibited lower corrosion rates with respect to Ni-P coatings. Such a reduction was about 21.6-92.2%. This behavior was attributed to the presence of reinforcement as barriers for corrosive ion diffusion through the coating plus the changes in detected phases and thickness. Electrochemical impedance spectroscopy test results also demonstrated that the increase in the polarization resistance for composites coatings was about 18.4-85.3% after 1 h immersion in a 0.6M NaCl solution; however, when the immersion time increased to 24 h, such increased resistance changed to 18.1 to 73.1%. Totally, despite the lower deposition rate, the presence of MoS2 and nano-SiO2 particles were more effective than toner particles to raise the corrosion rate of the Ni-P coating.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Rapid solidification during metal additive manufacturing (AM) leads to non-equilibrium microsegregation, which can result in the formation of detrimental phases and cracking. Most of the microsegregation models, assume a Scheil-type solidification, where the solidification interface is planar and there exists local equilibrium at the interface along with either zero or infinite solute diffusion in the respective participating phases - solid and liquid. This assumption leads to errors in prediction. One has to account for finite solute diffusion and the curvature at the dendritic tip for more accurate predictions. In this work, we compare different microsegregation models that do and do not consider finite diffusion and dendrite tip kinetics against the experiments. We also propose a method to couple dendrite tip kinetics with the diffusion module (DICTRA®) implemented in Thermo-Calc®. The models which accounted for both finite diffusion and dendrite tip kinetics matched well with the experimental data.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

The effect of transition metal substitution for Fe and the structural and magnetic properties of Gd2Fe16Ga0.5TM0.5 (TM=Cr, Mn, Co, Ni, Cu, and Zn) compounds were investigated. Rietveld analysis of X-ray diffraction indicates that all the samples crystallize in the hexagonal Th2Ni17 structure. The lattice parameters: a, c and unit cell volume show TM ionic radii dependence. Both Ga and TM atoms show preferred site occupancy for 12j and 12k sites. The saturation magnetization at maximum room temperature was observed for Co, Ni, and Cu of 69, 73, and 77 emu/g, respectively while minimum value was observed for Zn (62emu/g) doping Gd2Fe16Ga0.5TM0.5. Highest Curie temperature of 590 K was observed for Cu doping which is 15% and 5% and thesehigher than Gd2Fe17 and Gd2Fe16Ga compounds, respectively. The hyperfine parameters viz. hyperfine field and isomer shift, show systematic dependence on the TM atomic number. The observed magnetic and Curie temperature behavior in Gd2Fe16Ga0.5TM0.5 is explained on the basis of Fe(3d)-TM(3d) hybridization. The superior Curie temperature and magnetization value of Co, Ni, and Cu doped Gd2Fe16Ga0.5TM0.5 compounds as compared to pure Gd2Fe17 or Gd2Fe16Ga makes Gd2Fe16Ga0.5TM0.5 a potential candidate for high-temperature industrial magnet applications.

This paper investigates the evolution of microstructures and precipitations of an ultra-low iron alloy 625 subjected to long term aging treatment by scanning electron microscope (SEM) and X-ray diffraction(XRD). Use ASTM G28A acid Fe3(SO4)2 erosion to represent intergranular corrosion weightlessness and corrosive morphology. The result shows that alloy at 750C by aging treatment for 40h, precipitated γ'' phase in the grain boundary. In high density area of γ'' phase, occurs γ'' phase to δ phase degeneration transformation by aging treatment for 200h and the needle-like δ phase becomes more with time prolonged. And γ'' phase degenerated to δ phase completely until treated for 1000h. The sample which has aging treatment tends to have intergranular corrosion and mainly because alloy element spreading leads to dilution area and grain boundary precipitated phase, plus interlaced δ phase’s dissolving, which makes sample grain particle fall off and this results in apparent weightlessness. The weightlessness rate(WLR) is related with precipitated volume score. With aging sensitization time change, can be described by Johnson-Mehl-Avrami equation, i.e.: $WLR=44.32\left[1-\text{exp}\left(-\frac{t}{10.99}\right)\right]+44.62\left[1-\text{exp}\left(-\frac{t}{327.8}\right)\right]+1.267\left(mm/a\right)$

Classical antibacterial drugs were designed to target specific bacterial properties distinct from host human cells to maximize potency and selectivity. These designs were quite effective as they could be easily derivatized to bear next generation drugs. However, the rapid mutation of bacteria and their associated acquired drug resistance have led to the rise of highly pathogenic superbug bacterial strains for which treatment with first line drugs is no match. More than ever, there is a dire need for antibacterial drug design that goes beyond conventional standards. Taking inspiration by the body’s innate immune response to employ its own supply of labile copper ions in a toxic attack against pathogenic bacteria, which have a very low Cu tolerance, this review article examines the feasibility of Cu-centric strategies for antibacterial preventative and therapeutic applications. Promising results are shown for the use of Cu-containing materials in the hospital setting to minimize patient bacterial infections. Studies directed at disrupting bacterial Cu regulatory pathways elucidate new drug targets that can enable toxic increase of Cu levels and perturb bacterial dependence on iron. Likewise, Cu intracellular chelation/prochelation strategies effectively induce bacterial Cu toxicity. Cu-based small molecules and nanoparticles demonstrate the importance of the Cu ions in their mechanism and display potential synergism with classical drugs.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

Aluminium bronzes possess a unique combination of high strength and wear and corrosion resistance in aggressive environments; thus, these alloys find wide application in marine, shipbuilding, aviation, railway, offshore platform applications and other fields. Iron-aluminium bronzes (IABs) are the cheapest and most widely used. When the aluminium content is above 9.4 wt%, IAB is biphasic (i.e. it undergoes -transformation) and can be subjected to all heat-treatment types depending on the desired operating behaviour of the bronze component. This article presents correlations (mathematical models) between the primary mechanical characteristics (yield limit, tensile strength, elongation, hardness and impact toughness) and the ageing temperature and time of quench at 920°C in water Cu-11Al-6Fe bronze, obtained using the centrifugal casting method. The microstructure evolution was evaluated depending on the ageing temperature and time changes. Overall, the research was conducted in three successive inter-related stages: a one-factor-at-a-time study, planned experiment, and optimisations. Four optimisation tasks, which have the greatest importance for practice, were formulated and solved. The defined multiobjective optimisation tasks were solved by searching for the Pareto-optimal solution approach. The decisions were made through a nondominated sorting genetic algorithm (NSGA-II) using QstatLab. The optimisation results were verified experimentally. Additional samples were made for this purpose, quenched at 920°C in water and subjected to subsequent ageing with the optimal values of the governing factors (ageing temperature and time) for the corresponding optimisation task. The comparison of the results for the mechanical characteristics with the theoretical optimisation results presents good agreement.

Undoubtedly the Wageningen B-screw Series is the most widely used systematic propeller series. It is very popular to preselect propeller dimensions during the preliminary design stage before performing a more thorough optimization, but in the smaller end of the market it is often used to merely select the final propeller. Over time the originally measured data sets were faired and scaled to a uniform Reynolds number of 2·10⁶ to increase the reliability of the series. With the advent of the computer, polynomials for the thrust and torque values were calculated based on the available data sets. The measured data are typically presented in the well-known open-water curves of thrust and torque coefficients K_T and K_Q versus the advance coefficient J. Changing the presentation from these diagrams to efficiency maps reveals some unsuspected and surprising behaviours, such as multiple optima when optimizing for efficiency or even no optimum at all for certain conditions. These artefacts get more pronounced at higher pitch to diameter ratios and low blade numbers. The present work builds upon the paper presented by the author at the AMT’17 and smp’19 conferences and now includes the extended efficiency maps, as suggested by Danckwardt, for all propellers of the Wageningen B-screw Series.

Zn–Ni plating is indispensable in various industries because of its high corrosion resistance. However, Ni has been reported to trigger allergies; thus, an alternative Ni-free plating is desired. Zn–Fe plating is considered to be a promising candidate, albeit its corrosion resistance still needs to be improved. The corrosion resistance of Zn–Fe plating is expected to increase by the addition of Mo as the third alloying element as it is more noble than Zn and Fe. In this study, Zn–Fe–Mo plating with a corrosion resistance nearly equivalent to that of the Zn–Ni plating was fabricated. Zn–Fe–Mo plating was electrically deposited from continuously agitated plating baths prepared by mixing ZnSO₄, FeSO₄, Na₂MoO₄, Na₃C₆H₅O₇, and Na₂SO₄ using Fe or Ni plates as the substrate. The surface morphology, composition, crystal phase, and electronic state of Mo of the platings were investigated by SEM-EDS, XRD, and XPS. The anti-corrosion performance was evaluated by Tafel extrapolation method. Formation of plating comprising a Mo containing alloy phase was found to be crucial for improving corrosion resistance. The Zn–Fe–Mo plating demonstrates promise for replacing anti-corrosion Zn–Ni platings.

In order to design effective protective coatings against corrosion, the polyvinyl alcohol (PVA) as compound and composite with silver nanoparticles (nAg/PVA) were electrodeposited on copper surface employing electrochemical techniques such as linear potentiometry and cyclic voltammetry. A new paradigm was used to distinguish the features of coatings, i.e., a Deep Convolutional Neural Network (CNN) was implemented to automatically and hierarchically extract the discriminative characteristics from the information given by optical microscopy images. The main arguments that invoke a CNN implementation in the surface science of materials are the following: artificial intelligence techniques can be successfully applied to learn differences between surface coatings; based on their popularity for image processing, CNN can model images related to the problem of coatings; deep learning is able to extract the features that are distinguishable between material surfaces. To provide an overview of the copper surface, CNN was applied on microscope slides (CNN@microscopy) and inherently learnt distinctive characteristics for each class of surface morphology. The material surface morphology controlled by CNN without the interference of the human factor was successfully conducted, in our study, to extract the similarities/differences between unprotected and protected surfaces to establish the PVA and nAg/PVA performance to retard the copper corrosion.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

The direct methane to methanol (MTM) oxidation is a grand challenge in catalysis, with profound economical implications for the modern chemical industry. Bioinspired metal-organic frameworks (MOFs) with active iron and copper sites have been emerging very recently as innovative catalytic platforms to accomplish the MTM conversion under mild conditions. This review discusses the current state of the art regarding the application of MOFs with iron and copper catalytic centers to perform the MTM reaction, with a focus on the diverse spectroscopic techniques used to unveil the electronic and structural properties of the MOF catalysts at a microscopic level. We explore the synthetic strategies employed to incorporate iron and copper sites into different MOF topologies, the efficiency and selectivity of the iron- and copper-bearing MOF catalysts, and the ensuing MTM reaction mechanisms proposed on the basis of spectroscopic characterization supported by theory. In particular, we evidence how the combination of complementary spectroscopic tools probing different regions of the electromagnetic spectrum is particularly useful to reach a satisfactory understanding of the key reaction pathways and intermediates. Finally, we provide a critical perspective on future directions to advance the use of MOFs to accomplish the MTM reaction.

In recent years, electrochemical methods utilizing reactive electrochemical membranes (REM) have been recognized as the most promising technologies for the removal of organic pollutants from water. In this paper, we propose a 1D convection-diffusion-reaction model concerning the transport and oxidation of oxalic acid (OA) and oxygen evolution in the flow-through electrochemical oxidation system with REM. It allows the determination of unknown parameters of the system by treatment of experimental data and predicts the behavior of the electrolysis setup. There is a good agreement in calculated and experimental data at different transmembrane pressures and initial concentrations of OA. The model provides an understanding of the processes occurring in the system and gives the concentration, current density, potential and overpotential distributions in REM. The dispersion coefficient was determined as a fitting parameter and it is in good agreement with literary data for similar REMs. It is shown, that the oxygen evolution reaction plays an important role in the process even under the kinetic limit, and its contribution decreases with increasing total organic carbon flux through the REM.

Replacing carbon by hydrogen is a huge step towards reducing CO₂ emissions in the iron- and steel-making industry. The reduction of iron oxides using hydrogen plasma smelting reduction as an alternative to conventional steel-making routes has been studied at Montanuniversitaet Leoben, Austria. The aim of this work was to study the slag formation during the reduction process and the reduction behaviour of iron oxides. Furthermore, the reduction behaviour of iron ore during continuous feeding was assessed. Mixtures of iron ore and calcined lime with a basicity of 0, 0.8, 1.6, 2.3, and 2.9 were melted and reduced by hydrogen. The off-gas composition was measured during the operations to calculate the process parameters. The reduction parameters, namely the degree of reduction, degree of hydrogen utilisation, produced iron, and slag, are presented. The results of the batch-charged experiments showed that at the beginning of the reduction process, the degree of hydrogen utilisation was high, and then, it decreased over the operation time. In contrast, during the continuous-feeding experiment, the degree of hydrogen utilisation could be kept approximately constant. The highest degrees of reduction and hydrogen utilisation were obtained upon the application of a slag with a basicity of 2.3. The experiment showed that upon the continuous feeding of iron ore, the best conditions for the reduction process using hydrogen could be applied.

A comparative study of the physicochemical properties of natural bentonite clays of Pogodayevо (Republic of Kazakhstan, mod.1) and Dash-Salakhli (Republic of Azerbaijan, mod.2) deposits and modification of the bentonite clay with polyhydroxocations of iron (III) and aluminium (III). It-wasestablished that the modification of natural bentonitesusing polyhydroxocations of iron (III) and aluminium(III) by the method of "co-precipitation" leads to a change in their chemical composition, structural and sorption properties. The results showed that hydroxy-aluminum cations ([Al3O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe were intercalated into clay layers, which led to an increase in the values of d001 and specific surface areas compared to those of the original bentonite, from 37 to 120 for the Pogodaevo bentonite and from 51 to 172 respectively for bentonite from the Dash-Salakhli deposit. It is shown that modified sorbents based on natural bentonite are finely porous objects with a predominance of pores of 1.5−6.0 nm in size. As a result, there is a significant increase in the specific surface area of sorbents. Modification of bentonite with polyhydroxocations of iron (III) and aluminium (III) by the "co-precipitation" method also leads to an increase in the sorption capacity of the sorbents obtained with respect to nickel (II) cations. Modified bentonites were used for the adsorption of Ni (II) ions from the model solution. Ni (II) was absorbed in a neutral pH solution. The study of equilibrium adsorption showed that the data are in good agreement with the Langmuir isotherm model. The maximum adsorption capacity of the Ni (II) monolayer obtained from the Langmuir equation was 25.0 mg/g (mod. 1_Al_5-c), 18.2 mg/g (mod. 2_Al_5-c) for Al-bentonite and 16.7 mg/g (mod. 1_Fe_5-c), 10.1 (mod. 2_Fe_5-c) for Fe-bentonite. The kinetics of adsorption is considered. The high content of Al-OH anion exchange centresin them determines the higher sorption activity of Al-modified bentonites.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

The potential agricultural use of metal nanoparticles (NPs) for slow-release micronutrient fertilizers is beginning to be investigated by both industry and regulatory agencies. However, the impact of such NPs on soil biogeochemical cycles is not clearly understood. In this study, impacts of a commercially-available copper NPs on the soil nitrification kinetics was investigated via batch experiments. The X-ray absorption near edge structure spectroscopy analysis showed that the NPs readily oxidized to Cu(II) and strongly retained in soils with minimum dissolution (<1% of total mass). The Cu2+ (aq) at 1mg/L showed the beneficial effect on the nitrification, an increase in the rate of nitrification kinetics (Vmax). However Vmax was negatively impacted by ionic Cu at 10-100mg/L and CuNP at 1-100 mg/L. The trace metal toxicity of soil nitrifiers seems to be critical in the soil nitrification processes. Among CuNPs, the suppressed nitrification kinetics was concentration dependent at >10mg/L. The reaction products of surface oxidation such as the release of ionic Cu seem to play an important role in suppressing the nitrification process. Considering the potential use of copper NPs as a slow-release micronutrient fertilizer, further studies are needed in heterogeneous soil systems.

Substituted bis(iminophosphoranyl)methanes are CH acidic compounds that can form complexes with formally dianionic central carbon centres. The reaction of H₂C(Ph₂P=NDip)₂ (≡ H₂L), Dip = 2,6-diisopropylphenyl, with one equivalent of di-n-butylmagnesium afforded the methanide complex [HLMgnBu] 1. Treatment of complex 1 with phenylsilane in aromatic solvents at elevated temperatures afforded the methanediide complex [(LMg)₂] 2 presumably via the MgH intermediate [(HLMgH)_n] (n = 1 or 2). The reaction of 1 with LiAlH₄ in diethyl ether yielded the AlH complex [HLAlH₂] 3. Alternatively, this complex was also obtained from the reaction of H₂L with AlH₃∙NMe₃. The molecular structures of [HLMgnBu] 1, [(LMg)₂] 2, and [HLAlH₂] 3 are reported. Complex 3 shows no sign of H₂ elimination to a methanediide species at elevated temperatures in contrast to the facile elimination of the putative reaction intermediate [(HLMgH)_n] (n = 1 or 2) to form [(LMg)₂] 2. The chemical properties of complex 2 were investigated and this complex appears to be stable against coordination with strong donor molecules.

The evolution of metals micro/nano-structure upon severe plastic deformation (SPD) is still far to be theoretically explained, while experimental datasets are persistently growing for several decades. Major problem associated with understanding of SPD is related to a fact that the latter is a synergetic product of several competing physical effects which alter the material micro/nano-structure. In attempt to find deformational boundaries, where predominantly one mechanism determines the micro/nano-structure, in this paper we propose a continuous piecewise model for the analysis of experiments on material hardness vs strain of SPD processed materials. The novelty of this approach lies in its ability to find, as free-fitting parameters, the strain breakpoints which separate different micro/nano-structure modes generated upon SPD process. The model is applied to analyse experimental data for polycrystalline samples of pure iron and two distinctive strain breakpoints are revealed with good accuracies. This finding is in a good agreement with our earlier results on TEM microscopy studies on pure iron polycrystals after SPD treatment.

Biofilms are communities of microorganisms that can colonize biotic and abiotic surfaces playing a significant role in the persistence of bacterial infection and antibiotic resistance. About 65% and 80% of microbial and chronic infections are produced by biofilm formation. The increase in infections by multi-resistant bacteria draws attention to the discovery of new drugs based on natural inhibitory molecules. The inhibition of diguanylate cyclases (DGCs), the enzyme implicated in the synthesis of the second messenger, cyclic diguanylate (c-di-GMP), involved the biofilm formation, represents a potential method for preventing the biofilm development. It has been extensively studied using PleD protein as a model of DGC for in silico studies as virtual screening and as a model for in vitro studies in biofilms formation. In the present study 224205 molecules from natural products database, ZINC15 has been evaluated through molecular docking and molecular dynamic simulation, our result suggests trans-Aconitic acid (TAA) as a possible starting point for hit-to-lead methodologies to obtain new molecules capable of inhibiting the PleD protein and hence blocking the biofilm formation.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

Hydroxamic acid (HA) derivates displayed antibacterial and antifungal activities. HA with various numbers of carbon atoms (C2, C6, C8, C10, C12 and C17), complexed to different metal ions Fe(II/III), Ni(II), Cu(II) and Zn(II) were evaluated for their antimycobacterial activities and their anti-biofilm activities. Some derivates, among others HA12Fe2, inhibited the development of Mycobacterium tuberculosis, Mycobacterium bovis BCG and Mycobacterium marinum biofilms and could even attack pre-formed Pseudomonas aeruginosa biofilm. Proteomic profiles showed that the potential targets of HA10FeCl were mainly related to mycobacteria stress adaptation, involving cell wall lipid biosynthesis, drug resistance and tolerance, siderophore metabolism. This study provides new insights regarding the antimycobacterial activities of the HA and their complexes, especially about their potential antibiofilm activities.

This work aims to follow the corrosion behavior of copper in 3 wt% NaCl solution in the presence of a bio-oily extract. Spent coffee grounds (SCG), a highly recyclable and usable biomass - often thrown away and becoming a serious threat to the environment - , has a fraction of oils (12%) that we have opted to use as a corrosion inhibitor for copper. The extraction was carried out using n-hexane as the solvent for the decoction. The oily fraction was analyzed by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). Potentiodynamic polarization measurements have revealed SCG extract acts as a cathode-type inhibitor for copper in saline media, mainly preventing the diffusion of oxygen molecules toward the substrate. As the extract concentration increased, the inhibition efficiency has improved as well, reaching 95.78 % with 0.6 g/L of SCG extract. The obtained results by electrochemical impedance spectroscopy (EIS) are in accordance with the order of inhibitory efficiency obtained by potentiodynamic polarization. We have found that the SCG extract adsorption process on copper surface is spontaneous and complies with Langmuir isotherm.

Poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) named further PVBA was investigated as protective coating for copper corrosion in 0.9 % NaCl solution using electrochemical measurements such as, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization associated with Atomic Force Microscopy (AFM). The PVBA coating on the copper surface (Cu-PVBA) was modeled in methanol containing PVBA. Its inhibitory properties against corrosion was comparatively discussed with those of the copper sample treated in methanol without polymer (Cu-Me) and of untreated sample (standard copper). A protective performance of PVBA coating of 80 % was computed from electrochemical measurements, for copper corrosion in NaCl solution. Also, AFM images designed a specific surface morphology of coated surface with PVBA, clearly highlighting a polymer film adsorbed on the copper surface, which presents certain deterioration after corrosion, but metal surface was not significantly affected compared to those of untreated samples or treated in methanol, in the absence of PVBA.

Abstract: Lipodystrophies (LDs) are rare, complex disorders of the adipose tissue characterized by selective fat loss, altered adipokines profile and metabolic impairment. Sirtuins (SIRTs) are class III NAD+-dependent histone-deacetylases linked to fat metabolism. SIRT1 plays a critical role in metabolic health by deacetylating target proteins in tissues including liver, muscle and adipose tissue. Circulating SIRT1 levels have been found to be reduced in obesity while increased in anorexia nervosa and in patients experiencing weight loss. We evaluated circulating SIRT1 levels in relation to fat amount in 32 lipodystrophic patients affected by congenital or acquired LDs compared to non-LD subjects (24 with anorexia nervosa, 22 normal weight and 24 with obe-sity). SIRT1 serum levels were higher in LDs as compared with normal weight subjects (mean ± SEM: 4.17 ± 0.48 vs. 2.59 ± 0.20 ng/mL) or subjects with obesity (1.7 ± 0.39 ng/mL), whereas they were close to those measured in anorexia nervosa (3.44 ± 0.46 ng/mL). Our findings show that within the LD group there was no relationship between SIRT1 levels and the amount of body fat. The mechanisms responsible for secretion and regulation of SIRT1 in LD deserve further investi-gation.

This article presents, for the first time, the kinetics and the general conversion features of a 3-initiator system (A/B/N), based on proposed mechanism of Mokbel et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using copper complex as the initiator. Higher FRP and CP conversion can be achieved by co-initiators concentration [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals S' and S. The FRP and CP conversion is proportional to, respectively, the nonlinear and linear power of bI[A][B], where b and I are the absorption coefficient and the light intensity, respectively. System in air has lower conversion than in laminate due to the oxygen inhibition effects. For thick samples (with thickness z), there is an optimal concentration [A*] which is inverse proportional (bzI), in contrast with very thin sample, in which the conversion is an increasing function of [A] and [B]. The unique feature of dark polymerization in CP conversion enables the polymerization to continue in living mode, in contrasts with that of the radical-mediated pathway in most conventional FRP. The measured results of Mokbel et al are well analyzed and matching the predicted features of our modeling.

The reaction between 5-acetylbarbituric acid and 4-dimethylthiosemicarbazide or 4-hexamethyleneiminyl thiosemicarbazide produces 5-acetylbarbituric-4-dimethylthiosemicarbazone (H2AcbDM) and 5-acetylbarbituric-4N-hexamethyleneiminyl thiosemicarbazone (H2Acbhexim). Eight new complexes with different cooper (II) salts have been prepared and characterized using elemental analysis, molar conductance, UV–vis, ESI-HRMS, FT-IR, magnetic moment, EPR and cyclic voltammetry. In addition, three-dimensional molecular structures of [Cu(HAcbDM)(H2O)2](NO3)·H2O (3a), [Cu(HAcbDM)(H2O)2]ClO4 (4), and [Cu(HAcbHexim)Cl] (6) were determined by single crystal X-ray crystallography, and was carried out an analysis of their supramolecular structure. The H-bonded assemblies were further studied energetically using DFT calculations, MEP surface and QTAIM analyses. In these complexes, the thiosemicarbazone coordinates to the metal ion in an ONS-tridentate manner, in the O-enolate/S-thione form. The electrochemical behavior of the thiosemicarbazones and their copper(II) complexes has been investigated at room temperature using the cyclic voltammetry technique in DMFA. The Cu(II)/Cu(I) redox system was found to be consistent with the quasi-reversible diffusion-controlled process.

This study employs a high-fidelity numerical framework to determine the plastic material flow patterns and temperature distributions that lead to void formation during friction stir welding (FSW), and to relate the void morphologies to the underlying alloy material properties and process conditions. Three aluminum alloys, viz., 6061-T6, 7075-T6, and 5053-H18 were investigated under varying traverse speeds. The choice of aluminum alloys enables investigation of a wide range of thermal and mechanical properties. The numerical simulations were validated using experimental observations of void morphologies in these three alloys. Temperatures, plastic strain rates, and material flow patterns are considered. The key results from this study are: (1) The predicted stir zone and void morphology are in good agreement with the experimental observations, (2) The temperature and plastic strain-rate maps in the steady-state process conditions show a strong dependency on the alloy type and traverse speeds, (3) The material velocity contours provide a good insight into the material flow in the stir zone for the FSW process conditions that result in voids as well as those that do not result in voids. The numerical model and the ensuing parametric studies presented in this work provide a framework for understanding material flow under different process conditions in aluminum alloys, and potentially in other alloys. Furthermore, the utility of the numerical model for making quantitative predictions and investigating different process parameters to reduce void formation is demonstrated.

Under the same seismic load, different local topography will have different effects, which is an important research field in seismic engineering. Hills are connected with valleys is a very typical terrain. Taking this terrain as an example, its response to the most destructive SH waves in the earthquake is studied. By simplifying and dividing the model, the wave functions satisfying the wave equation and boundary conditions in each region are constructed by using the complex function and moving coordinate method. The equations satisfying the boundary continuity conditions are established. With the help of calculation software, the numerical results are obtained. The influence of different parameters on ground motion is discussed.

Spherical microparticles of TiO₂ were synthesized by the ionic liquid-assisted solvothermal method at different reaction time (3, 6, 12 and 24h). The properties of the prepared photocatalysts were investigated by means of UV-vis diffuse-reflectance spectroscopy (DRS), BET surface area measurements, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The results indicated that the efficiency of phenol degradation was related with a time of the solvothermal synthesis as determined for TiO₂_EAN(1:1)_24h sample. Microparticles of TiO₂_EAN(1:1)_3h formed during the only 3h of synthesis time revealed really high photoactivity under visible irradiation – 75%. This value increased to 80% and 82% after 12h and 24h, respectively. The photoactivity increase was accompanied by the increase of the specific surface area thus pores size, as well as ability to absorb UV-vis irradiation. The high efficiency of phenol degradation of IL-TiO₂ photocatalysts was ascribed to the interaction between the surface of TiO₂ and ionic liquid components (carbon and nitrogen).

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Positively charged polyelectrolytes hold significant potential as materials for creating antibacterial coatings. Water-soluble macromolecules can be easily deposited onto a treated surface through various techniques, forming a film that provides antimicrobial properties to the surface through electrostatic interactions with bacterial membranes. The structural and molecular weight characteristics of the polymers play a crucial role in the physical and mechanical properties of the coatings. In this study, we investigated the properties of branched polyethyleneimine (PEI) and linear polydiallyldimethylammonium chloride (PDADMAC) coatings with different molecular weights of polymer samples to determine their suitability as stable coatings with antibacterial properties against foodborne bacteria. Using thermogravimetric analysis, dynamometry, and dynamic light scattering, we examined the physicochemical and mechanical properties of the macromolecules in water solutions and in coatings. Microbiological study was conducted to analyze the biocidal activity of the polycations in solutions and on the surface of coatings. Our findings showed that the moisture saturation of the polycationic coatings did not significantly depend on the chemical nature of charged groups or the molecular weight or architecture of macromolecules. Moreover, biocidal activity was not found to depend on the molecular weights of PEI and PDADMAC. However, the lowering of the molecular weight of polymers resulted in the loss of cohesive forces in the coatings and to dramatically loss of the stability towards wash-off with water. The diffusion coefficient (D0) of macromolecules was identified as a key parameter for the wash-off mechanism. Films formed by molecules with D0 below 1×10-7 cm2/s demonstrated high resistance to wash-off procedures. We demonstrated that PEI and PDADMAC samples with high molecular weights showed high antimicrobial activity towards L. monocytogenes. Our results highlight the importance of macromolecule characteristics in the development of new biocidal coatings based on polycations.

Alzheimer’s disease (AD) is the leading cause of dementia, characterised by beta-amyloid plaques, neurofibrillary tangles, and oxidative stress. Iron is suspected to enhance disease progression, and chelation may be a potential treatment. We propose that Aloysia citrodora Paláu (AC), a plant in the Verbenaceae family, can act as a moderate chelator of iron. It may reduce the effect of iron on beta-amyloid 1-42 (Aβ1-42) aggregation. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to demonstrate that AC can interact with iron (II) and iron (III), the two most abundant forms of iron within the body. DPV was also used to characterise Aβ1-42 aggregation, and two main features were obtained. The first is the tyrosine peak (~0.6 V) decreased in magnitude over time, which is a sign of aggregation and folding. The other is a conglomerate of peaks at ~0 V, whose identity is unknown. Furthermore, iron (II) increased the rate of tyrosine peak depreciation, and the addition of AC negated this induced effect. This implied that iron (II) increases Aβ1-42 aggregation into higher order, and AC may be an effective countermeasure.

Experimental optimization of analytical methods based on solid-phase microextraction (SPME) is a complex and labor-intensive process associated with uncertainties. Using the theoretical basics of SPME and finite element analysis software for the optimization proved to be an efficient alternative. In this study, an improved finite element analysis-based model for SPME of volatile organic compounds (VOCs) by porous coatings was developed mainly focussing on the mass transport in coatings. Benzene and the Carboxen/polydimethylsiloxane (Car/PDMS) coating were used as the model VOC and a porous SPME coating, respectively. It has been established that in the coating, volumetric fractions of Carboxen, PDMS, and air are 33, 42 and 24%, respectively. Knudsen diffusion in micropores can slow down a mass transport of analytes in the coating. When PDMS was considered as the solid part of the coating, lower root-mean-square deviation of the modeling results from experimental data was observed. It has been shown that the developed model can be used to model the extraction of VOCs from air and water samples encountered in a typical SPME development method procedure. It was possible to determine system equilibration times and use them to optimize sample volume and Henry’s law constant. The developed model is relatively simple, fast, and can be recommended for optimization of extraction parameters for other analytes and SPME coatings. The diffusivity of analytes in a coating is an important property needed for improved characterization of existing and new SPME polymers and analytical method optimization.

This investigation mainly focused on the microstructural analysis of Al based hybrid metal matrix composites. Aluminium as base metal and reinforced with 2% B4 C, ZrO2 (2%,4%,6%), SiC (4%,8%,12%). Specimens were manufactured by using conventional stir casting technique. Hybrid metal matrix composites were examined by using Scanning electron microscope. This research explained XRD, EDS and Fractography analysis. This investigation shows the reinforced material has given better results in all aspects than pure Al6061 alloy and homogeneous dispersion of particles inside the matrix. Porosity, delamination, cracks, particle distributions were observed through microstructural analysis. Additionally determined the crystal size of pure Aluminium 6061 alloy and hybrid composites.

Direct interaction with the neuronal cells is a prerequisite to deciphering useful information in understanding the underlying causes of diseases and functional abnormalities in the brain. Precisely fabricated nanoelectrodes provide the capability to interact with the brain in its natural habitat without compromising its functional integrity. Considerable research has been focused on the employment of vertical nanotubes as nanoelectrodes due to large-scale intracellular recording capability and longer-term intracellular access that arise from their unique geometry. Despite many types of nanotube structures reported in the literature, a limited subset of the nanotubes has been investigated for neural interfacing. This work reports on the fabrication and optimisation of vertically oriented titania nanotube arrays as a scalable electrode platform for neural interface application. To this end, the doping was performed by incorporating a selected group of biologically active metallic ions, including zinc, strontium, and copper, into TiO2 lattice and its effect was studied with respect to the structural, electrochemical and biological properties of the nanotube arrays. It was found that doping can change the length, diameter and wall thickness of the nanotubes. Among pure and doped samples, the copper-doped TiO2 nanotubes demonstrated the highest electrochemical and biological performance. Our results suggest that the doping can be used as a promising method to optimise the properties of nanotube arrays for the development of high-performance neural electrodes.

The objective of this study was to investigate the impact of athletes' respiratory muscle strength, as assessed through maximal inspiratory (MIP) and expiratory pressure (MEP), on aerobic endurance, as indicated by maximal oxygen consump-tion (Max VO2) kinetics. Respiratory muscle strength was assessed using a digital spirometer (Pony FX Cosmed, Italy), while maximal oxygen utilization capacity was measured using a breath-by-breath automatic portable gas analysis system (Cosmed K5, Italy). Statistical analysis was conducted utilizing SPSS 22.0. Based on the standardized regression coefficients (β), it was found that MEP (mean ± SD: 130.95 ± 42.82) and inspiratory diaphragmatic circumference values significantly influenced ventilatory equivalent (VE), oxygen consumption (VO2), and carbon dioxide pro-duction (VCO2). Conversely, the remaining predictor variables did not exhibit a sig-nificant effect on VE (mean ± SD: 134.80 ± 36.69), VO2 (mean ± SD: 3877.52 ± 868.47 ml), and VCO2 (mean ± SD: 4301.27 ± 1001.07 ml). In contrast, measurements of chest circumference (mean ± SD: 91.40 ± 10.72 cm), MEP, and diaphragmatic cir-cumference during inspiration (mean ± SD: 95.20 ± 10.21 cm) were found to signifi-cantly impact Max VO2 (mean ± SD: 58.52 ± 10.74 ml/kg/min), while the other pre-dictor variables did not demonstrate a significant effect on Max VO2. Conclusively, the study revealed that measured values of diaphragmatic circumference during inspiration and MEP exerted a notable influence on Max VO2, VE, VO2, and VCO2. Our findings underscore the importance of considering respiratory muscle strength in assessing and enhancing athletes' aerobic performance. These insights contribute to a deeper understanding of the interplay between respiratory function and exercise capacity, offering potential avenues for optimizing training regimens and perfor-mance outcomes in athletic contexts.

A novel process design for damage-free and highly accurate positional integration of an optical multi-axial force sensor into a hollow tube by means of rotary swaging is introduced. Numerical simulations reveal relevant process phenomena of thin disc joining inside a pre-toothed hollow tube and help to find an optimal process design. Experimental trials show a significant effect of axial material flow and the number of tools in a rotary swaging process. By taking these effects into account, a successful form- and force-fit joining of the sensor carrying discs into the tube can be achieved. A successful joining of an optical sensor for bending forces and torque measurement shows hysteresis-free sensory behavior and thus backlash-free joining of the sensor carrier discs. The paper finishes with presenting an approach for closed-loop position controlling during the joining process and numerically investigation of the process design.

Speleothems have proven to be one of the most reliable terrestrial archives for palaeoclimate research. However, due to the complexity of karst systems, long-term monitoring and high-resolution analyses of the cave atmosphere and water geochemistry have become essential to better constrain the factors that control calcite growth and how geochemical palaeoclimate proxies are encoded into speleothems. While calcite precipitation incorporates the palaeoclimate signals into the speleothem fabric, certain conditions in caves can favour dissolution, which may form hiatuses or even destroy these signals. In extreme cases, in-cave dissolution by dripwater can form cup-shaped features (i.e., corrosion cups), which were the main focus of this study. The study site in Postojna Cave, Slovenia, was investigated through cave climate monitoring and drip and cup water sampling, which took place during 2017–2021. We found that the cups are fed by low calcium drips as the consequence of the thin vadose zone above the cave. Due to the specific configuration of airflow pathways, the study site accumulates high levels of CO2 (&gt;10,000 ppm), which shifts low calcium dripwater into undersaturation. This causes dissolution on rock surfaces and speleothems on the cave floor. The results of this study have broader significance in addressing the suitability of cave environments and speleothems used in paleoclimate research.

Co/TiO2 catalysts with different cobalt loadings (3.8, 7.5 and 15 wt%) were prepared by impreg-nation method of Co(NO3)2 .6H2O over titania. Samples containing Co(NO3)2 .6H2O and TiO2 in stoichiometric proportions in order to obtain CoTiO3 and Co2 TiO4 phases were also synthesized. The effect of the calcination treatment at two different temperatures, 550 and 1150 °C was investigated. Characterizations by several techniques, such as XRD UV-vis-NIR, DRS, Raman and XPS were carried out. XRD showed the coexistence of three phases: CoTiO3; Co2TiO4 and Co3O4 after calci-nation at 550°C, while the calcination at high temperature (1150°C) leads to single-phase systems (CoTiO3 or Co2TiO4). Diffuse reflection and XPS spectroscopy showed that divalent cobalt occupies octahedral sites in the ilmenite phase and both tetrahedral and octahedral sites in the spinel phase. The catalytic performances of the prepared catalysts, calcined at the two different temperatures, were evaluated in the oxidative dehydrogenation reaction (ODH) of ethane to ethylene. The con-version values were almost comparable for all the samples, calcined at 550 °C, and comparable the ethylene selectivity were recorded, slightly higher only in the case of CoTiO3. The calcination at 1150°C did not modify the overall activity (ethane conversion values around 20%), however, the production of COx becomes more significant. The study examined the influence of the reaction mixture composition, specifically the presence of water, and reveals a slight increase in the yield of ethylene accompanied by a decrease in the overall catalyst activity. This behavior is likely attributed to an increase in the surface concentration of hydroxyl species (OH), resulting in heightened surface acidity.

Abstract: Alzheimer's Disease (AD) is a progressive uncurable neurodegenerative disease affect-ing millions worldwide. Various methods, including drug therapies and light emission diode (LED) irradiation, are promising alternatives for preventing and reducing the rapid progression of neurodegenerative diseases, also stimulating the reconstructing of neural tissue structures. In this study, we evaluated the neuroprotective and restorative effects of taurine combined with LED on human neuroblastoma cells (SH-SY5Y), under oxidative stress condition, a considerable modulator in AD. We evaluated LED at the wavelength of 660 nm and taurine under different concentrations before and after exposing SH-SY5Y cells to different concentrations of hydrogen peroxide (H2O2), assessing mitochondrial activity by the MTT colorimetric test and labeling live cell mitochondria by fluorescence using MitoTracker Orange. Cell viability was also evaluated by the trypan blue exclusion assay, and we verified cellular morphological structures by scan-ning electron microscopy (SEM). It was observed that neuroprotective effects are achieved by both LED and taurine when cells are exposed to them and later are stressed with H2O2. Compar-ing both agents, LED irradiation is sufficient to stimulate cell proliferation, representing an af-fordable candidate to contribute against neurodegeneration.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

The composite coatings prepared by mixing the 5 wt.% of polyaniline with commercial alkyd-based paint are applied on carbon steel. The polyaniline emeraldine chloride salt is prepared by procedure recommended by IUPAC, deprotonated by ammonia hydroxide, and reprotonated with the sulfamic, succinic, citric, and acetic acids with different doping degrees or oxidation states. The steel samples with base and composite coatings are immersed in 3% NaCl and the corrosion current density is determined after 96 h in-site using ASTM 1,10-phenanthroline method. The samples are also inspected by the optical microscope. It is shown that composite coatings reduce the possibility of blister formations and delamination. The corrosion current density and the appearance of the corrosion products, which area is determined by ImageJ softer, closely follow the initial oxidation state of the polyaniline. The role of the initial state of the polyaniline is discussed. It is suggested that such behavior could be connected with the oxygen reduction reaction mechanism that proceeds mainly via two electron paths on the polyaniline particles, releasing a much smaller amount of hydroxyl ions, responsible for the delamination and blister formations of the commercial coatings.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

Current hydrogen production is based on the reforming process leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. Production of green hydrogen from water electrolysis using intermittent sources (e.g., solar, eolic) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for efficient nickel-based electrocatalysts. For these reasons, herein, a review of recent progress is presented.

Re-interpretation of the Fermat principle governing propagation of light in media within the Ramsey Theory is suggested. Complete bi-colored graphs corresponding to the light propagation in media are considered. The vertices of the graphs correspond to the points of the real physical space, in which light sources or sensors are placed. Red links in the graphs correspond to the actual optical paths, emerging from the Fermat principle. A variety of optical events: refraction, reflection, etc. may be involved in the light propagation. Green links, in turn, denote the trial/virtual optical paths, which actually do not occur. The Ramsey Theorem states that within the graph containing six points, inevitably, actual or virtual optical cycle will be necessarily present. Implementation of the Ramsey Theorem to the light propagation in metamaterials is discussed. The Fermat Principle states that in metamaterials a light ray in going from point S to point P must traverse an optical path length L that is stationary with respect to variations of this path. Thus, bi-colored graphs built of links corresponding to maxima or minima of optical paths become possible. Graphs, comprising six vertices, inevitably will demonstrate optical cycles, built of the mono-colored links corresponding to the maxima or minima of the optical path. The notion of the “inverse graph” is introduced and discussed. The total number of triangles in the “direct” (source) and “inverse” Ramsey optical graphs is the same, Optical interpretation of the infinite Ramsey Theorem is suggested.

Application of the Ramsey Theory to the set of the points placed in the plane is discussed. Consider a set of N points located in the same plane. The straight lines connecting these points are yikx=αikx+βik i,k=1...N. Listed below values of slopes αik are possible: αik&gt;0; αik=0; αik is not defined; αik&lt;0. Following coloring procedure is introduced: we connect the pairs of points for which αik&gt;0, αik=0 or αik is not defined, with the red links, and the pairs of points for which αik&lt;0 place with green links. The suggested coloring procedure enables building of the complete bi-colored graph for any set containing N points located in the same plane. We apply the Ramsey theorem to the complete graph emerging from the suggested coloring. For the set containing N=6 points at least one monochromatic triangle will necessarily appear in the graph. The values of the slopes αik depend on the chosen coordinate system. The rotation of coordinate axes changes the coloring of the graph; however, at least one monochromatic triangle will be present for N=6. The introduced coloring procedure diminishes the order of the symmetry group of the regular hexagon, irrespectively to the orientation of the coordinate axes. We hypothesized that this will be true for arbitrary regular n-polygon, independently on the orientation of coordinate axes. The inverse bi-color Ramsey graphs arise, when we replace red links appearing in the source graph with red ones, and vice versa. The total number of triangles in the “direct” and “inverse” Ramsey graphs is the same. We considered the particular case of the set of points for which αik&gt;0 or αik&lt;0 is true in the given coordinates. In this particular case, the rotation of the Cartesian coordinate axes to the angle θ=π2 yields the inverse complete graph. Generalization of this coloring for an arbitrary number and arbitrary location of the source points is introduced.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close to the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li embedded into various matrices. The one-dimensional lattice built of the identical metallic micro-elements m_eff connected by ideal springs k_1 representing various media such as polydimethylsiloxane and soda-lime glass is treated. The optical and acoustical branches of longitudinal modes propagating through the lattice are elucidated for various ratios ω_1/ω_p . The 1D lattice built of the thin metallic wires giving rise to the low frequency plasmons is treated. The possibility of the anti-resonant propagation, strengthening the effect of the negative mass occurring under  = p = 1 is addressed.

A novel and simple method to improve the corrosion resistance of copper by constructing a 3D 1-dodecanethiol self-assembled monolayers (SAMs) in 3.5% NaCl solution is reported in this study. Several drops of 1% H3PO4 solution are thinly and uniformly distributed on copper surface to form a 3D nanostructure constituted by Cu3(PO4)2 nanoflowers. The anticorrosion properties of 1-dodecanethiol SAMs on copper surface and on copper surface treated with H3PO4 solution were evaluated. Results demonstrated that 1-dodecanethiol SAMs on bare copper surface exhibit good protection capacity, whereas a copper surface pretreated with H3PO4 solution can substantially enhance the corrosion resistance of 1-dodecanethiol SAMs.

Voronoi entropy for the random patterns and patterns demonstrating various elements of symmetry are calculated. The symmetric patterns are characterized by the values of the Voronoi entropy very close to those inherent to random ones. This contradicts the idea that the Voronoi entropy quantifies the ordering of the seed points, constituting the pattern. The extension of the Shannon-like formula embracing symmetric patterns is suggested. Analysis of Voronoi diagrams enables revealing of the elements of symmetry of the pattern.

Surface processes such as coatings, corrosion, photocatalysis, and tribology are greatly diversified by acid-base interaction at the surface overlayer. This study focuses on the action of metallic copper surface as an electron donor/acceptor related to inactivation of viruses; it was found that regarding Cu2O or Cu materials electrostatic interaction plays a major role in virus inactivation. We applied TPPE method to clarify the mechanism of electron transfer (ET) occurring at light irradiated copper surfaces. The TPPE characteristics was strongly influenced by the environments, which correspond to the temperature and environment dependence of the total count of emitted electrons in the incident light wavelength scan (PE total count, NT), the photothreshold, and further the activation energy (E) analyzed from Arrhenius plot of NT values obtained in the temperature-increase and subsequent temperature-decrease processes. In this study we reexamined the dependence of the TPPE data from two types of Cu metal surfaces: Sample A, which was mechanically abraded in alcohols, water, and air, and Sample C, which was only ultrasonically cleaned in these liquids. The NT for both Samples slowly increased with increasing temperature, reached a maximum (NTmax) at 250C (maximum temperature, Tmax), and after that decreased. For Sample A the NTmax value decreased in the order H2O > CH3OH > C2H5OH > (CH3)2CHOH > C3H7OH, although the last alcohol gave Tmax = 100C, while with Sample C the NTmax value decreased in the order: C3H7OH > (CH3)2CHOH > C2H5OH > CH3OH > H2O. Interestingly, both orders of the liquids were completely opposite: this means that Cu surface can possess two-way character. The NT intensity was found to be strongly associated with the change of the hydroxyl group (Cu-OH) to the oxide oxygen (O2) in the O1s spectra in the XPS measurement. The difference between the above orders was explained by the acid-base interaction mode of the Cu-OH group with the adsorbed molecule on the surfaces. The H2O adsorbed on Sample A produces the electric dipole Cu-OH+---:OH2 (--- hydrogen bond), while the C3H7OH and (CH3)2CHOH adsorbed on Sample C produce ROH+---:O(H)-Cu (R = alkyl groups). Gutmann’s acceptor number (AN) representing the basicity of the liquid molecules was found to be related to the TPPE characteristics: (CH3)2CHOH (33.5), C2H5OH (37.1), CH3OH (41.3), H2O (54.8) (the AN of C3H7OH could not be confirmed). With Sample A the values of NTmaxa and EaUp1 both increased with increasing AN (Up1 means the 1st temperature-increase process). On the other hand, with Sample C the values of NTmaxc and EcUp1 both decreased with increasing AN. These findings suggest that Sample A acts as an acid, while Sample C functions as a base. However, in the case of both types of Samples A and C the NTmax values were found to increase with increasing EUp1. It was explained that the EUp1 values depending on the liquids originate from the difference in the energy level of the hydroxyl group radical at the surface denoted. This is able to attract electrons in the neighborhood of the Fermi level of the base metal by tunnelling. After that due to Auger emission electrons are released, leading to the ET in the overlayer. These electrons are considered to have a strong ability of reducibility.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

Paper is one of the most promising materials for food packaging and wrapping due to its low environmental impact, but surface treatments are often needed to improve some performance, e.g. the resistance to fats and oils. In this context, this research is focused on the formulation of a new paper bio-coating. Paper was coated with liquids containing Poly(hexano-6-lactone) (PCL), Glycerol and variable percentages of starch (5 - 10% w/w PCL dry weight), agar agar (0 - 1.5% w/w PCL dry weight) and PEG (5% or 15% w/w PCL dry weight) to improve coating uniformity and diffusion. A Design of Experiments approach was implemented to find statistically reliable results in terms of best coating formulation. Coated paper was characterized through mechanical and physical properties. Results showed that agar content (1.5% w/w PCL dry weight) has a beneficial effect on increasing the resistance to oil. Furthermore, the best coating composition has been calculated, and it is: 10% w/w PCL dry weight of Starch, 1.5% w/w PCL dry weight of agar and 15% w/w PCL dry weight of PEG.

In this study, grit blasting pretreatment was used to improve the adhesion and corrosion resistance and microhardness of Ni-W/SiC nanocomposite coatings fabricated using conventional electrodeposition technique. Prior to deposition, grit blasting and polishing (more commonly used) pretreatment were used to prepare the surface of the substrate and the 3D morphology of the pretreated substrates was characterized using laser scanning confocal microscopy. The coatings surface and the cross section morphology were analyzed using scanning electron microscopy (SEM). The chemical composition, crystalline structure, microhardness, adhesion, and the corrosion behavior of the deposited coatings were characterized using energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester, scratch tester and electrochemical workstation, respectively. The results indicated that the grit blasting and SiC addition, improved the microhardness, adhesion and corrosion resistance. The Ni-W-SiC nanocomposites pretreated by grit blasting exhibited the best adhesion strength, up to 36.5 ± 0.75 N. Its hardness was the highest and increased up to 673 ± 5.47Hv and its corrosion resistance was the highest compared to the one pretreated by polishing.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex &gt; organic-matter–clay mineral complex &gt; iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Turner syndrome (TS) is caused by a complete or partial absence of an X or Y chromosome, including chromosomal mosaicism, affecting 1 in 2,500 female live births. Sister chromatid exchange (SCE) is used as a sensitive indicator of spontaneous chromosome instability. Cells from mosaic patients constitute useful material for SCE evaluations as they grow under the influence of the same genetic background and endogenous and exogenous factors. We evaluated proliferation dynamics and SCE frequencies of 45,X and 46,XN cells of 17 mosaic TS patients. In two participants, 45,X cells exhibited a proliferative disadvantage in relation to 46,XN cells after 72h of cultivation. The analysis of mean PI showed significant differences between 45,X and 46,XN lineages; however there were no intraindividual differences. On the other hand, mean SCE frequencies showed no differences between the two lineages, but there were intraindividual differences in 5 patients. The absence of mean SCE frequency differences between 45,X and 46,XN lineages may indicate that both were equally unstable, as more than 70% of the 46,XN lineages had an anomalous karyotype. However, 46,XN had a higher mean PI, suggesting that the amount of cells with a karyotype distinct from 45,X may increase with time in mosaic TS women.

In common model testing practise, the measured values of the self propulsion test are split into the characteristics of the hull, the propeller and into the interaction factors. These coefficients are scaled separately to the respective full scale values and subsequently reassembled to give the power prediction. The accuracy of this power prediction depends {\em inter alia} on the accuracy of the measured values and the scaling procedure. An inherent problem of this approach is, that it is virtually impossible to verify each single step, because of the complex nature of the underlying problem. In recent years the scaling of the open-water characteristics of propeller model tests attracted a renewed interest, fuelled by competitive tests, which became the norm due to requests of the customer. This paper will show the influence of different scaling procedures on the predicted power. The prediction is compared to the measured trials data and the quality of the prediction will be judged. The procedures examined are the standard ITTC~1978 procedure plus derivatives of it: the Meyne, the strip method and the βᵢ-method.