Pomegranate peel is a natural source of phenolics, claimed to possess healing properties, among which antioxidant and antidiabetic. In line with this evidence, the ethyl acetate PGE extract, obtained by Soxhlet from the peel of Dente di cavallo DC2 variety and characterized by a 4% amount of ellagic acid, has been studied for its hypoglycemic, antiglycation and antioxidative cytoprotective properties, in order to support a possible further nutraceutical interest. The α-amylase and α-glucosidase enzyme inhibition, interference with advanced glycation end-products (AGE) formation and metal chelating abilities were evaluated as hypoglycemic mechanisms. Also, considering that oxidative stress is associated with hyperglycemia complications, PGE antioxidant cytoprotective properties under hyperglycemic conditions were assayed. Phenolic profile was characterized by integrated chromatographic and spectrophotometric methods. Under our experimental conditions, PGE strongly inhibited the tested enzymes, especially α-glucosidase, and exerted chelating and antiglycation properties. Also, it reduced both ROS and GSH levels under hyperglycemic conditions, thus suggesting its ability to support cell functions by counteracting intracellular oxidative stress. Along with ellagic acid, rutin was the major identified flavonoid (about 4 %) of PGE. Present results suggest PGE to be a possible remedy for hyperglycemia management and encourage further studies to exploit its promising properties.

This study evaluates the feasibility of stabilizing clay bricks with marble cutting waste (MCW). This waste currently discarded in huge quantities as a sludge resulted from sawing the marble blocks to slabs, grinding and polishing of marble processes to the landfills located around the marble processing factories located in the Shaq El-Thoban industrial zone, Cairo governorate, Egypt causing negative impacts on the environment, health and sustainable development. Experimental investigations were carried out to explore the effect of addition of the MCW in different clay-base mixes at different percentages up to 25% at the expense of the hydrated lime. Cement, hydrated lime and MCW are the three types of solidification agents used, clay and sand were also added in the formulations of the unfired clay brick specimens. Laboratory cylindrical stabilized and compressed specimens were made, and then they were cured in a humidity chamber for 2 and 4 weeks, then after were air dried, tested and evaluated according to the Egyptian code for the building by the stabilized and compressed earth soil (ECBS, 2016). To enhance the durability of the cured specimens, transparent silicon – based paint was used for this purpose. The laboratory results demonstrate high potential usage of MCW based additives up to 15% incorporating HL. In addition, the used paint could be an effective treatment way for the use of stabilized bricks in a wet environment. The use of eco-friendly building materials will be a great contribution for the environmental advantages and suggest a remarkable economical alternative to the fired building units.

Dealing with and maintaining high-quality standards in the design and construction phases is challenging, especially for on-site construction. Issues like improper implementation of building components and poor communication can widen the gap between design specifications and actual conditions. To prevent this, particularly for energy-efficient buildings, it's vital to develop resilient, sustainable strategies. These should optimize resource use, minimize environmental impact, and enhance livability, contributing to carbon neutrality by 2050 and climate change mitigation. Traditional post-occupancy evaluations, which identify defects after construction, are impractical for addressing energy performance gaps. A new, real-time inspection approach is necessary throughout the construction process. This paper suggests an innovative guideline for prefabricated buildings, emphasizing digital 'self-instruction' and 'self-inspection'. These procedures ensure activities impacting quality adhere to specific instructions, drawings, and 3D models, incorporating relevant acceptance criteria to verify completion. This methodology, promoting alignment with planned energy-efficient features, is supported by BIM-based software and Augmented Reality (AR) tools, embodying Industry 4.0 principles. BIM and AR bridge the gap between virtual design and actual construction, improving stakeholder communication and enabling real-time monitoring and adjustments. This integration fosters accuracy and efficiency, key for energy-efficient and Nearly Zero-Energy Buildings, marking a shift towards a more precise, collaborative, and environmentally sensible construction industry.

Over the years, the need for autonomous systems such as drones, also known as unmanned aerial vehicles (UAVs), has significantly increased in popularity across several industries, including the military. The Internet of Battlefield Things (IoBT) represents a modern technological advancement that significantly enhances the operational efficacy of defense systems. It establishes an integrated military force by connecting individuals to intelligent technology in drones, radios, equipment, antennas and ground stations. This is achieved through the utilization of cloud and edge computing, sensors, mobile devices, embedded systems, and IoT-based systems. However, IoBT security is significantly compromised by enemies that exploit the vulnerabilities and malicious intrusions that specifically target the external environment or to obtain sensitive data. In addition, a comprehensive understanding of cyberattacks and countermeasures is essential for assuring the security of IoBT. On the other hand, as cyber threats get more complicated, trust becomes increasingly important for the security of digital systems. Within this context, the zero trust architecture contends that the security of a complex network is inherently vulnerable to internal and external threats. In defense, UAV security system applications, for example, the primary purpose of the zero trust architecture is to limit the vulnerability of military UAV systems to cyberattacks, hence reducing the possibility of data breaches and illegal entry. This study conducts a systematic review aimed at identifying different aspects of cybersecurity strategies for protecting UAV systems within the IoBT domain. Furthermore, zero trust architecture is presented in the study as an effective prospective solution to the security issues that develop in defense UAV systems.

Education is one of the most important tools available to policymakers and non-governmental bodies to promote a change in the behavior of society and to address the climate crisis, in line with the 4^th and 13^th Sustainable Development Goals of the United Nations 2030 Agenda. Project-based learning (PBL) addresses real and global challenges and allows the academic and professional formation of students. As part of the reflection stage of the educational action research method using the Business Canvas Model (BMC), pedagogic deficiencies were identified in the PBL and a didactic proposal was elaborated to emulate the interaction of students with the ecosystems of society. A prototype for improving the management of organic manures as soil amendments was initially developed, to provide the students with a quick start on the first steps of the proposed project. In the 10 sessions designed for the PBL (Make it happen!), the students elaborate a more sophisticated artifact in response to the demands of potential clients, as per the outcomes of the primary market research (5^th session). Active teaching methods and tools, such as a modified template of the BMC with the Rumsfeld’s matrix, aid the metacognition of students and their competences development. In a double session of the PBL, the primary market research is organized with key stakeholders of the agroindustry to enquire about the feasibility of the implementation of the technological solution and the logistics at farm level. Finally, the evaluation relies on the suitability of the upgraded prototype to respond customers’ demands.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

The analysis of the key factors which prevent or contribute to the promotion and development of the Power Purchase Agreements (PPAs) in order to meet the sustainability goals represents an important issue which worth being investigated, especially in the situation in which entering in bilateral relations inside this contract has a powerful meaning in achieving new climate targets, developing and improving the use of green energy, and promoting a sustainable green economy. The main goal of this research is to identify and analyze the main factors which help or pre-vent the promotion and development of a PPA, in order to meet the sustainability goals by promoting a green economy. For this research survey based on comparative analysis, questionnaires and interviews with energy experts, Spearman’s correlation matrix and IBM SPSS Statistics for Window are also used. The results suggest that although there are positive interest and an open attitude towards the PPA from both sides (sellers and buyers), but there is still place for improvement, the lack of knowledge or the insufficient measures taken so far being two of the reasons way until now in Romania we do not have a developed PPA market and the level of knowledge regarding this type of mechanism is quite low.

Hydrogen plays an important role in the implementation of Australia’s Net-Zero Strategy. It competes with lithium-ion rechargeable batteries in the electrification of Australian land transportation sector, and can provide an alternative energy storage medium for the greening of the country’s electrical grid system. This paper reviews the role hydrogen plays in the current government’s Net-Zero strategy, and investigates the potential role of other bioenergy sources. It is found that hydrogen and batteries play essentially complementary roles in reducing transport emissions, and that the former energy source is more suited to the operation of long-distance commercial service vehicles than batteries. It is suggested that bioenergy fuels such as biomethane, second generation biofuels and HVO can provide suitable bridging alternatives in the event that Australia’s EV strategy is unable to meet the 2030 target.

Already more than 140 countries consider or have pledged to reach net-zero emission targets by 2050 or earlier and the share of global emissions falling into an emission pricing scheme has steeply increased over the past three years. Even where there are no direct implications for industry (yet), there is a series of subtle pressure points driving an increasing number of companies across the globe to work towards climate neutrality and pledging ambitious emission reduction goals. This article sheds light on the pressure points, the subtle triggers, the underlying considerations as well as the hoped-for benefits for industrial companies from achieving net-zero emissions. The observations and ideas presented in this paper are derived from quantitative data obtained via the Energy Efficiency Index of German Industry (EEI) and qualitative data. Not only societal, work force, supply chain and investor expectations play a large role, but also many strategic considerations which have the potential to make the company more resilient and profitable, particularly in time of crisis. Those companies that do not move towards decarbonisation, on the other hand, may face a costly late-mover disadvantage. This piece uncovers subtle interconnections, helping stakeholders from industry and beyond to grasp opportunities and challenges ahead.

Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

Recently, the relationship between emotional arousal and depression has been studied. Focusing on this relationship, we first developed an arousal level voice index (ALVI) to measure arousal levels using the Interactive Emotional Dyadic Motion Capture database. Then, we calculated ALVI from the voices of depressed patients from two hospitals (Ginza Taimei Clinic [GTC] and National Defense Medical College hospital [NDMC]) and compared them with the severity of depression as measured by the Hamilton Rating Scale for Depression (HAM-D). Depending on the HAM-D score, the datasets were classified into a no depression (HAM-D<8) and a depression group (HAM-D≥8) for each hospital. A comparison of the mean ALVI between the groups was performed using the Wilcoxon rank-sum test and a significant difference at the level of 10% (p = 0.094) at GTC and 1% (p = 0.0038) at NDMC was determined. The area under the curve (AUC) of the receiver operating characteristic was 0.66 when categorizing between the two groups for GTC, and the AUC for NDMC was 0.70. The relationship between arousal level and depression severity was indirectly suggested via ALVI.

Acetylcholine (ACh) is the best one characterized neurotransmitter. Its central roles in the cholinergic areas and central nervous system (CNS) and peripheral (PNS) synapses are well known. It was the first molecule identified as a neurotransmitter and appears to be phylogenetically the oldest one signaling molecules. ACh was detected in bacteria, protozoa, fungi, algae and primitive plants, indicating that the cholinergic system was widely distributed in living organisms before its appearance in the nervous system. The autonomous nervous system (ANS) is an integral part animal kingdom history. It determines fight-escape reactions as well as outlining the vital and cognitive functions bio-organization rhythms. The virus (Covid-19) extraneous effects acting on it could help to better understand its functions. The Blast results show some factors like protein that can be implicated such as bungaro-toxins, phospholipase A2 and the similar prothrombin activator protein. A positive correlation with different toxins is obtained and the Covid-19 double pathogenic mechanism theory is proposed. The process allows us to outline the possibility about toxic-like factors presence.

An explanation of the origin of dark matter is suggested in this work. The argument is based on symmetry considerations about the concept of mass. In the Wigner's view, the rest mass and the spin of a free elementary particle in flat space-time are the two invariants that characterize the associated unitary irreducible representation of the Poincar\'e group. The Poincar\'e group has two and only two deformations with maximal symmetry. They describe respectively the de Sitter (dS) and Anti de Sitter (AdS) kinematic symmetries. Analogously to their shared flat space-time limit, two invariants, spin and energy scale for de Sitter and rest energy for Anti de Sitter, characterize the unitary irreducible representation associated with dS and AdS elementary systems. While the dS energy scale is a simple deformation of the Poincaré rest energy and so has a purely mass nature, AdS rest energy is the sum of a purely mass component and a kind of zero-point energy derived from the curvature. An analysis based on recent estimates on the chemical freeze-out temperature marking in Early Universe the phase transition quark-gluon plasma epoch to the hadron epoch supports the guess that dark matter energy might originate from an effective AdS curvature energy.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

The pyrolysis process has emerged as an attractive option for waste treatment. In this technology, inorganic compounds play catalytic effects in the pyrolytic reaction of organic materials, increa-sing the char's yield, porosity, and physicochemical properties. The present research investigates and compares the slow pyrolysis of spent coffee grounds (SCG) using potassium hydroxide (KOH) (weight ratio of 1:1) and landfill leachate membrane concentrate (LLMC) residue (weight ratio of 1:1) as pyrolitic additives. We hypothesized that the high content of alkali and alkaline earth metals in LLMC could enhance the yield or improve the quality of the carbon-based material produced in pyrolysis. This strategy could be a sustainable alternative for valorizing SCG and landfill wastes, replacing catalyzing agents such as steam, CO2, and chemical additives used on an industrial scale. The char yields in slow pyrolysis ranged from 18 to 24%. The SCG had a low specific surface area (4.5 m2 g-1), contrasting with the notable surface areas observed in both ac-tivated chars. In particular, the KOH-activated char displayed a higher surface area than the LLMC-activated char (1960 vs. 1130 m2 g-1). On the other hand, the combustion enthalpy of the LLMC-activated material was estimated at 22 MJ kg-1. This value was 22% higher than the energy enthalpy of SCG and KOH-activated char used for comparison. Our findings confirm that pyrolysis of SCG with KOH produces a microporous material with a high specific surface area. In contrast, the resulting LLMC-activated char demonstrates a higher calorific value. Our findings could contribute to establishing potential industrial applications for SCG and LLMC residues to produce energy and high-value materials.

Investments in small and medium-sized anaerobic digestion facilities have the potential to boost biogas production in Greece and other EU countries. This study aimed to evaluate the economic feasibility of anaerobic digestion facilities equipped with combined heat and power (CHP) units ranging from 50 to 400 kW, while treating livestock waste. For this purpose, data were gathered from various livestock operations (dairy cattle, poultry, swine, dairy sheep and goat) regarding their annual production, revenues, electricity and fuel usage, and waste generation. Waste samples were then collected and analyzed to assess their biochemical methane production potential. The capital and operational costs of anaerobic digestion facilities, from 50 and 400 kW, were calculated using the equations developed within the “eMT cluster” project. Findings indicate that current feed-in tariffs (FIT) of 0.21 € kWh-1 are insufficient to incentivize investment in anaerobic digestion facilities with capacities below 250 kW, highlighting the need for increased FIT rates or capital expenditure subsidies. Recommendations include shifting towards simplified technology and business models with reduced farmer involvement, coupled with supportive legislative framework and long-term electricity price guarantees. These measures are expected to foster the implementation of anaerobic digestion projects in the animal husbandry sector.

Frass generated during the production of black soldier fly larvae is taking the interest of scientists and horticultural producers because it is a material from the biotransformation of organic waste, it has several nutrients that can be used by plants, and its recent focus on its biostimulant capacity. The thermal-composting process is a stabilization that improves physical and chemical properties of treated wastes, allowing better performance in plants compared to its fresh state. In this research, thermocomposted frass was evaluated as a germination substrate for kale seeds (Brassica olerasea). To achieve this, it was evaluated the phytotoxicity in different concentrations on the seeds, and seedlings were grown in a germination substrates mixed with 20, 40, 60, 80 and 100% of frass. The treatment with 20% frass showed the highest values of seedling height, stem diameter, number of leaves, length, and width of first true leaf and length and width of cotyledons, reduced the content of phenols and tannins antioxidants but the content of flavonoids increased compared to the control and the rest of mixtures.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Artificial intelligence (AI) has found extensive applications in the sustainability domain. The municipal solid waste incineration (MSWI) process can achieve waste-to-energy (WTE) goals through the assistance of automation and information technologies. In theory, AI can facilitate the intelligent operation of the MSWI process, simultaneously achieving low pollution emissions and high production efficiency. This study provides an overview of AI applications in the MSWI process. Addressing fundamental challenges, the optimal control of the MSWI process is categorized into four aspects: modeling, control, optimization, and maintenance. Subsequently, this study conducts a detailed analysis and discussion of AI applications in each of these technological domains. In conclusion, this paper outlines the future research directions and provides an outlook on the fundamental issues pertaining to AI applications in the optimal control of the MSWI process.

The influence of aluminosilicate pozzolanic waste, specifically spent fluid catalytic cracking catalyst (FCCW) and metakaolin waste (MK) from expanded glass industry, on the properties of hardened Portland cement paste were analysed. The study involved replacing part of cement with FCCW and MK and observing their impact on hydration, microstructure, density and compressive strength of hardened cement paste. Various analysis methods were employed, including X-ray diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM), to understand the changes in the structure of hardened cement paste during hydration. The findings revealed that FCCW tends to accelerate cement hydration process due to its high surface area and pozzolanic activity. Notably, the formation of portlandite crystals was observed on FCCW particle surfaces in a specific direction. These crystals appeared smaller and developed in different directions in compositions containing a composite binder with mixture of FCCW and MK in a ratio 1:1. This could be influenced by pozzolanic reactions activated by fine particles of MK and the formation of calcium silicate hydrates (CSH) and calcium alumino silicate hydrates (CASH) in the presence of portlandite. XRD and TG results indicated that the specimens containing a composite binder exhibited the least amount of portlandite. The compressive strength of these specimens increased compared to control specimens, although the amount of cement was 9% lower.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

Investigating the potential impact of composting and recycling waste on income distribution are crucial to promote a fairer and more sustainable fresh tomato supply chain (FTSC). Therefore, this study aims to explore the potential of gaining extra income from recycling tomatoes waste generated along the FTSC and to calculate the contribution of extra income from recycling tomato waste to reduce income inequality along the FTSC. Data were collected from 136 greenhouse tomato producers, 60 wholesalers, 18 exporters, 120 domestic retailers, 22 overseas retailers, and 3 recycling facilities in Türkiye. Marketing cost, absolute marketing margin, relative marketing margin and net profit margin were used when economically analyzing the FTSCs. Research results showed that the net profit share of the producer decreased associated with the increasing number of intermediaries. Research results also showed that revenue gained from composting and recycling of product loss and waste increased the welfare of greenhouse producer more than other supply chain actors. When taking into account the revenue from composting and recycling of wastes, producers increased their net profit by 9.85% at first FTSC, while that of second and third FTSCs were 8.29% and 9.21%, respectively comparing to the prevailing conditions. The contribution of extra revenue from composting and recycling of wastes to retailers was more comparing wholesaler and exporter. Retailers and wholesalers gaining from recycling in domestic FTSCs was more comparing to overseas one. Close cooperation between producers, wholesalers, exporters, retailers, and recycling facilities is essential for the effective implementation of waste recycling initiatives. Organizing the training and education programs focused on waste management can increase the extra income of producers and active intermediaries in FTSC from composting and recycling tomato wastes. Offering financial incentives, grants, or subsidies can encourage producers and other actors within the supply chain to adopt waste recycling practices. Continuous research and innovation are crucial in identifying and developing new technologies, processes, and strategies to minimize food loss and waste. Dominating fair-trade practices to ensure that all FTSC actors may balance the income distribution among FTSC actors.

Genetic adaptation of Hermetia illucens (BSF) to suboptimal single sourced wastes can open new perspectives for insect production. Here, four replicate BSF lines were maintained on a single sourced, low-quality wheat bran diet (WB) or on a high-quality chicken feed diet (CF) for 13 generations. We continuously evaluated evolutionary responses in several performance traits to rearing at the two diets. Subsequently, we tested responses to interchanged diets, i.e. of larvae that had been adapted to low-quality feed and to high quality feed and vice versa to evaluate costs associated with diet adaptation. BSF were found to experience rapid adaptation to the diet composition. While performances on WB diet were always inferior to CF diet, the adaptive re-sponses were stronger to the former diet. This stronger response was likely due to stronger se-lection pressure experienced by BSF fed on the low-quality single sourced diet. The interchanged diet experiment found no costs associated with diet adaptation but confirmed diet adaptation for the larval biomass and insect frass traits for the WB diet treatment. Our results revealed that BSF can rapidly adapt to diet through evolutionary responses, which has potential to be utilized to produce lines tailored to specific diets.

Development of high nutritious bakery products with optimum utilization of food waste is a major challenge for food industries. Food waste is major challenge in an each country. The optimum utilization of food waste for sustainable development goal of country is important ant for growth of the nation. The aim of the present work is to prepare value-added composite flour mixed bread from wastes of fruit and vegetables. The composite flour was prepared in four formulations of Peel and Pomace Wheat Flour (PPWF), as PPWF1, PPWF2, PPWF3 and PPWF4. Compositing flour was blended by a mix of vegetable and fruits pomace powders and whole wheat flour. Indian gooseberry pomace powder, apple pomace powder, bottle gourd peel powder, and potato peel powder were used with whole wheat flour to make pomace and whole wheat flour compositions as PPWF1, PPWF2, PPWF3 and PPWF4. Broadly this work was divided into three phases, first phase has conducted nutritional and functional analysis on peel and pomace powders individually, which shows the significance of using them for our research work. The second phase works in the creation of composite flours with different composition ratios as discussed above as PPWF. This phase shows the nutritional and functional analysis of four composite flours. Out of these four flours, PPWF3 contained a good amount of fiber 8.16%, crude protein 3.18%, total phenolic content 14.48%, moisture 9.5%, vitamin C 13.64mg/100g, and total phenolic compound 14.48(mg/GAE/g) which are maximum and acceptable range values as compared to other three composite flours and the wheat flour-control group flour. Then in the third phase, the PPWF3 is used as a partial replacement ratio of wheat flour in wheat flour due to its high phenolic content, Vitamin C, and the richness of fibers. This composite flour is used to make bread dough, two samples G1 and G2 are made; out of which G2 offers better nutritional, functional, and sensory evaluations in comparison with refined wheat four bread is taken as a control group. Thus, such utilization of food wastes in bread making can generate a value of wastes and can improve nutritional attributes of bread, which may improve an individual’s health.

The volatile fatty acids (VFAs) productions, as well as particulate organics decomposition, soluble chemical oxygen demand (SCOD) yield, and the VFAs production pathways, of mesophilic and thermophilic anaerobic fermentation were investigated. Batch experiments showed that the decomposition rate of volatile suspended solids (VSS), particulate carbohydrate (P-C) and particulate protein (P-P) followed the first-order kinetic model at different temperature. However, the intermediates， accumulated in the process of protein or carbohydrate digestion had a more significant inhibitory effect on the production of VFAs during the mesophilic anaerobic acidification process. Thermophilic fermentation led to more accumulation of VFAs compared to mesophilic fermentation. Then 13C stable isotope labeling experiment demonstrated that, acetic (HAc), propionic (HPr) and butyric (HBu) could be produced from carbohydrate and protein digestion, but valeric (HVa) was only generated from the degradation of protein. Finally, the possible pathway of HVa synthesis was proposed.

The anaerobic digestion (AD) of rumen residues and wheat straw in different proportions of inoculum (66.67, 50, 33.33 %V/V) to substrate and their co-digestion potential have been exhaustively studied in this research. It explores variation of feedstock characteristics such as biodegradability and methane potential during AD and anaerobic co-digestion (ACoD) of rumen residues (RR) with wheat straw (WS), under mesophilic conditions. Comparative performance was made with a organic load rate of 18 gVS/L (with 2:1, 1:1 and 1:2 g/g VS of inoculum to substrate). Among different kinetic models studied (modified Gompertz model, transfer model and logistic function), the AD and ACoD of substrates showed better fit to Gompertz model (R2: 0.977–0.997) indicating variation in lag phase and methane production rate depending on the substrate characteristics. During AD, the methane yield improved as the inoculum ratio increased, however, there was no significant difference in ACoD yield from RR to WS for the inoculum to substrate ratios studied, due to the synergistic effect as a result. of greater biodegradability and optimal conditions (such as the C/N ratio). A comparison of methane generation means indicated that maximum methane production can be achieved by mixing rumen residue (75 %) and wheat straw (25 %) with a C/N ratio of (38.15).

In this study, the gravimetric characterization and analysis of the solubilized extract of the organic fraction of Urban Household Solid Waste (RSDU) from the municipality of Belém do Pará was carried out in order to obtain the composition of the collected materials and the characteristics of the liquid resulting from the solubilization of these materials . The waste used to carry out this research was collected door-to-door, in which the points and neighborhoods served were determined through the sectorization of these locations and representative statistical sampling. For the sectorization of neighborhoods, family income values ​​were considered as the main parameter. After collecting the solid waste, the material was sent to the facilities of the Federal University of Pará (FUPa), where the waste was classified into paper, cardboard, tetrapak, rigid plastic, soft plastic, metals, glass, organic matter, waste toilets, fabrics and others. The organic fraction of solid waste was separated and sent to the drying, crushing and packaging processes. Subsequently, the solubilized extract of the organic fraction of solid waste was obtained, following the methodology recommended by NBR standard nº 10.006/2004, of the Brazilian Association of Technical Standards and the values ​​obtained were compared with Ordinance GM/MS nº 888/2021 and CONAMA Resolution nº 357/2005, in addition to results obtained by other authors. After carrying out the gravimetric characterization, it was possible to obtain the average proportions of 5.09% paper, 3.20% cardboard, 0.94% tetrapak, 3.58% rigid plastic, 9.97% soft plastic, 2.00% metals, 55.57% organic matter, 1.86% glass, 14.26% sanitary waste, 3.23% fabrics and 3.00% other waste. High values ​​of organic residues were found in the gravimetric composition, which can be explained by the collection method used and the high humidity of the organic solid residues. In the analyzes of the solubilized extract, values ​​of Hp (3.69 to 4.92), Turbidity (791 to 1,733 uT), Apparent Color (8,500 to 12,500 uC), True Color (6,000 to 14,000 uC), Total Dissolved Solids (5,330 to 8,040 mg/L), Total Nitrogen (201.80 to 359.90 mg/L), Ammoniacal Nitrogen (161 to 289 mg/L), Nitrate (10 to 40 mg/L), Total Phosphorus (52.30 to 166.80 mg/L) and Chemical Oxygen Demand (28,701 mg/L to 38,608 mg/L), in addition to other measured parameters, in which such information makes it possible to check the similarities of the waste solubilization conditions to that of leachates from landfills, in addition to not being in compliance with environmental and health legislation, demonstrating risks to the local environment and public health.

Conventional hydrogen production, as an alternative energy resource, has relied on fossil fuels to produce hydrogen, releasing CO2 into the atmosphere. Hydrogen production via the dry forming of methane (DRM) process is a lucrative solution to utilize greenhouse gases, such as carbon dioxide and methane, by using them as raw materials in the DRM process. However, there are a few DRM processing issues, with one being the need to operate at a high temperature to gain high conversion of hydrogen, which is energy intensive. In this study, bagasse ash, which contains a high percentage of silicon dioxide, was designed and modified for catalytic support. Modification of silicon dioxide from bagasse ash was utilized as a waste material and the performance was explored of bagasse ash-derived catalysts interacting with light irradiation and reducing the amount of energy used in the DRM process. The results showed that the performance of 3%Ni/SiO2 bagasse ash WI was higher than that of 3%Ni/SiO2 commercial SiO2 in terms of the hydrogen product yield, with hydrogen generation initiated in the reaction at 300 °C. Using the same synthesis method, the current results suggested that bagasse ash-derived catalysts had better performance than commercial SiO2-derived catalysts when exposed to an Hg-Xe lamp. This indicated that silicon dioxide from bagasse ash as a catalyst support could help improve the hydrogen yield while lowering the temperature in the DRM reaction, resulting in less energy consumption in hydrogen production.

The larvicidal potential of olive mill waste water (OMWW) extract against mosquito larvae was evaluated. We exposed second instar Culex laticinctus (Edwards) and Aedes albopictus (Skuse) larvae to increasing OMWW concentrations. In addition, we tested the effects of long term exposure to a low OMWW concentration on larval development. The two mosquito species responded differently to OMWW extracts. Larval Cx. laticinctus showed higher vulnerability to increasing OMWW concentrations in comparison to Ae. albopictus. By contrast, Cx. laticinctus exposed to a low OMWW concentration until pupation did not exhibit survival differences, but rather sex-specific development responses. These trends were not observed in Ae. albopictus whose survival was significantly reduced following long exposer to OMWW extraction. These results showed that OMWW, which is known as agricultural byproduct waste, may be reused as a biopesticide.

Data centres, though a necessary part of modern society, are being stigmatised for consuming vast amounts of electricity for their operational and cooling needs. Due to Ireland’s reliance on fossil fuels to meet the increased energy demand of data centres, the data centres are contributing significantly to Ireland’s total carbon emissions. As much of this energy is expelled from data centres as waste heat energy, the potential for recycling some of this wasted heat energy was explored using environmentally friendly systems from recent publications. The recovered waste heat energy was applied in a vertical farming system, and the benefits of this waste heat to the vertical farm were analysed and quantified in two scenarios. Using conservative estimates, it was predicted that each vertical farm could be between 5-23% the size of the data centre and produce enough food to feed between 14-61 adults their daily calorie needs, and between 13-58 people their daily fresh produce requirements, depending on the scenario applied. For a more accurate prediction, each vertical farm would have to be assessed on a case-by-case basis. However, there was not enough data available on Irish data centres to perform these calculations.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Food security is a matter of global concern, as the supply of food is one of the basic needs, ensuring the survival of the species. The trend of globalization and development of the global economy has shifted the responsible, local consumption patterns towards an increased homogeneity of diets, with food products being disconnected from their source, leading to two major results: (1) increased global consumption, driven by the extensive availability of affordable seasonal foods throughout the year and (2) increased uncertainty in the supply chain – susceptible to disruptions, causing food insecurity. To determine what the nutritional model is in the case of the present study – Romania – we developed a questionnaire of 32 questions and distributed it to 1,053 respondents from Romania. The survey was conducted during 2021 and 2022, both in urban and rural areas with the aim of investigating the consumption pattern of the population. The analysis of the questionnaire data reveals overconsumption of animal products, starchy vegetables and bread and pastry products. This nutritional pattern with a high intake in animal protein, correlated with a lack of diversification, is extremely unsustainable, having a negative impact on human health and environmental health.behaviour towards a careful approach to food, environment and personal health, aims to identify consumption patterns that have the potential to increase the sustainability of the food system and a positive correlation with food security. Adopting sustainable dietary patters, based on short supply chains and mindful consumption, has great potential in restoring food security and resilience to adversity.

Food security is a matter of global interest, as the provision of food resources is the primary determinant of human existence. Food is one of the basic needs, ensuring the survival of the species. The trend of globalization and development of the global economy has shifted the responsible local consumption patterns to an increased homogeneity of diets, food products being disconnected from their source. This disconnection led to two major results: (1) increased global consumption, with seasonal foods now available throughout the year, and a decrease in food prices on the global market, and (2) increased uncertainty in the supply chain, susceptible to disruptions, as was the case during the Covid-19 pandemic. The present study, based on the research and analysis of third-party data on food security, sustainable diets, consumption patterns and recommended actions to change the current unsustainable consumer behaviour towards a careful approach to food, environment and personal health, aims to identify consumption patterns that have the potential to increase the sustainability of the food system and a positive correlation with food security. Adopting sustainable dietary patters, based on short supply chains and mindful consumption, has great potential in restoring food security and resilience to adversity.

Quantum cell automata (QCA) is a nanotechnology that uses a transistor-free structure to design digital circuits and overcome the limitations listed for CMOS circuits. The computing circuits that make up the bulk of computers can be designed and using this technology. Subtractors are a big part of computational circuits. This research deals with the design of a subtractor that due to the innovation in the design of this circuit and the novel arrangement of quantum cells of its kind has caused the number of cells used in the design of the circuit to reach its lowest value compared to previously designed circuits. The size of the circuit as well as the loss power are minimized compared to the circuits designed by the subtractors. Another trait clears of this circuit compared to many previous designs is its single-layer design, which reduces latency and noise in the output waveform. The circuit designed by the QCADesigner simulator is tested and simulated inadition the results are displayed in the simulated waveform. Also, the results of calculations for power dissipation in each QCA cell were evaluated by QCAPro software, which is a powerful tool for estimating power loss simulation. It has less implementation and level (single layer) than Previous designs.

During the novel coronavirus disease (COVID-19) pandemic, several environmental factors have influenced the activities and the protection policy measures. This has had a major effect on climate change and global environmental catastrophe. In many countries, the strategy of closing various activities such as tourism, industrial production, stopped normal life, transportation, among others. This closure has a positive impact on the environment. However, the massive use of masks and personal protection could significantly increase pollution worldwide. The impact on the environment needs to be calculated to have information for public health actions. In this study, we present a first overview of the potential impacts of COVID-19 on some environmental matrices in Bogota, Colombia.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

This paper aims to investigate the usage of waste from Absorbent Hygienic Products (AHP) as a fuel for gasification or pyrolysis, two attractive routes to obtain valuable products and dispose of this kind of waste. The study experimentally investigated the devolatilization of coarsely shred-ded materials from diapers, in a laboratory-scale bubbling fluidized bed made of sand, as a rep-resentative preparatory step of above-mentioned thermochemical conversions. Two versions of shredded materials were considered: as-manufactured diapers (AHPam, as a reference), and the cellulosic fraction of sterilized used diapers (AHPus). Results were presented, obtained from physic-chemical characterization of AHPam and AHPus (TGA, CHNS/O, proximate and ultimate analysis, XRF, ICP-AES, SEM-EDS) and their devolatilizations at 500-600-700-800°C, under two different atmospheres (air plus nitrogen, or pure nitrogen as a reference). Generally, temperature had most influenced syngas composition, with better performances under pure nitrogen. At 700-800 °C under pure nitrogen, the highest syngas quality and yield were obtained. For AHPam and AHPus, respectively: (i) H2 richness equaled 29.5 vol% and 23.7 vol%, while hydrocarbons poorness equaled 14.8 vol% and 7.4 vol% on dry, dilution-free basis; (ii) 53.7 Nl 100 gfuel-1 and 46.0 Nl 100 gfuel-1 were produced. Overall, AHP emerged as an interesting fuel for thermochemical conversions.

The HS-SPME GC-MS analysis of the volatile compounds adsorbed at the outer surface of lemon and grapefruit pectins obtained via hydrodynamic cavitation of industrial waste streams of lemon and grapefruit peels in water only suggests important new findings en route to understanding the powerful and broad biological activity of these new pectic materials. In agreement with the ultralow degree of esterification of these pectins, the high amount of highly bioactive α-terpineol and terpinen-4-ol points to limonene decomposition catalyzed by residual citric acid in the citrus waste peel residue of the juice industrial production.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

The bio-oil was largely produced by thermal pyrolysis of Jatropha-derived biomass wastes (denoted as Jatropha bio-oil) using a Pilot Plant with a capacity of 20 kg h-1 at Thailand Institute of Scientific and Technological Research (TISTR), Thailand. Jatropha bio-oil is an unconventional type of bio-oil, which is mostly composed of fatty acids, fatty acid methyl esters, fatty acid amides and derivatives, and consequently it contained large amounts of heteroatoms (oxygen ~ 20 wt.%, nitrogen ~ 5 wt.%, sulfur ~ 1000 ppm.). The heteroatoms, nitrogen especially, are highly poisonous to the metal or sulfide catalysts for upgrading of Jatropha bio-oil. To overcome this technical problem, we reported a stepwise strategy for hydrotreating of 100 wt% Jatropha bio-oil over mesoporous sulfide catalysts of CoMo/γ-Al2O3 and NiMo/γ-Al2O3 to produce drop-in transport fuels, such as gasoline- and diesel-like fuels. This study is very different from our recent work on co-processing of Jatropha bio-oil (ca. 10 wt%) with petroleum distillates to produce a hydrotreated oil as a diesel-like fuel (Chen et al., Catalysts 2018, 8, 59; http://dx.doi.org/10.3390/catal8020059). Jatropha bio-oil was pre-treated through a slurry-type high pressure reactor under severe condition, resulting in a pre-treated Jatropha bio-oil with relatively low amounts of heteroatoms (oxygen < 20 wt.%, nitrogen < 2 wt.%, sulfur < 500 ppm.). The light and middle distillates of pre-hydrotreated Jatropha bio oil was then separated by distillation at temperature below 240 oC, and the temperature of 240-360 oC. Deep hydrotreating of light distillates over sulfide CoMo/γ-Al2O3 catalyst was performed on a batch-type high pressure reactor at 350 oC and 7 MPa of H2 gas for 5 h. The hydrotreated oil was a gasoline-like fuel, which contained 29.5 vol.% of n-paraffins, 14.4 vol.% of iso-paraffins, 4.5 vol.% of olefins, 21.4 vol. % of naphthene compounds and 29.6 wt.% of aromatic compounds, and little amounts of heteroatoms (nearly no oxygen and sulfur, and less than 50 ppm of nitrogen), corresponding to an octane number of 44, and it would be suitable for blending with petro-gasoline. The hydrotreating of middle distillates over sulfide NiMo/γ-Al2O3 catalyst using the same reaction condition produced a hydrotreating oil with diesel-like composition, low amounts of heteroatoms (no oxygen and less than 50 ppm of sulfur and nitrogen), and a cetane number of 60, which would be suitable for use in drop-in diesel fuel.

Fish oil rich in polyunsaturated omega-3 fatty acids is extracted in high yield from anchovy filleting waste using d-limonene as green biosolvent in a simple solid-liquid extraction performed by mechanically stirring and maceration followed by limonene removal via evaporation under reduced pressure. As limonene is renewably obtained from waste orange peel, this protocol establishes a circular bioeconomy method to obtain valued omega-3 extracts from biowaste available worldwide in several million t/year amount. The method closes the materials cycle and opens the route to full valorisation of an important biological resource so far mostly discarded as waste. Significant economic opportunities benefiting local communities, the ecosystem and public health are anticipated.

In this paper, ground tire rubber (GTR) was mechano-chemically modified with road bitumen 160/220 and subsequently treated using a microwave radiation. The combined impact of bitumen 160/220 content and microwave treatment on short-term devulcanization of GTR were studied by thermal camera, wavelength dispersive X-ray fluorescence spectrometry (WD-XRF), static headspace and gas chromatography-mass spectrometry (SHS-GC-MS), thermogravimetric analysis combined with Fourier transform infrared spectroscopy (TGA-FTIR), oscillating disc rheometer and static mechanical properties measurements. The obtained results showed that bitumen plasticizer prevent oxidation of GTR during microwave treatment and simultaneously improves processing and thermal stability of obtained reclaimed rubber.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

We present here a theory of Majorana excitons, photo-excited conduction electron-valence band hole pairs, interacting with Majorana Fermions in a Kitaev chain of semiconductor quantum dots embedded in a nanowire. Using analytical tools and exact diagonalisation methods we identify the presence of Majorana Zero Modes in the nanowire absorption spectra.

Considering increasingly ambitious pledges by countries, pressure from society, investors, and clients further up the supply chain, the question for companies is not so much whether to take decarbonisation action, but what action and by when. However, determining an ideal mix of measures to apply ‘decarbonisation efficiency’ requires more than knowledge of technically feasible measures and how to combine them to achieve the most economic outcome: In this paper, the author describes seven aspects which heavily influence the composition of an ‘ideal mix’ that executive leadership needs to take a (strategic) position on. These aspects consider underlying motivations and span across (socio-)economic, technical, regulatory, strategic, corporate culture and environmental factors and further underline the necessity of clarity of definitions. How these decisions influence the determination of the decarbonisation-efficient ideal mix of measures, both in principle but also in terms of specific impact is further explored by providing examples. What choices are taken by German manufacturers in several of the aspects is disclosed by insights from about 850 responses to the ‘Energy Efficiency Index of German Industry’. Knowledge of the status quo, and clarity in definitions, objectives, time frames and scope are key.

In 2010, Parties to the Convention on Biological Diversity (CBD) adopted the Strategic Plan for Biodiversity 2011–2020 to address the loss and degradation of nature. Subsequently, most biodiversity indicators continued to decline. Nevertheless, conservation actions can make a positive difference for biodiversity. The emerging Post-2020 Global Biodiversity Framework has potential to catalyze efforts to ‘bend the curve’ of biodiversity loss. Thus, the inclusion of a goal on species, articulated as Goal B in the Zero Draft of the Post-2020 Framework, is essential. However, as currently formulated, this goal is inadequate for preventing extinctions, and reversing population declines; both of which are required to achieve the CBD’s 2030 mission. We contend it is unacceptable that Goal B could be met while most threatened species deteriorated in status and many avoidable species extinctions occurred. We examine the limitations of the current wording and propose an articulation with robust scientific basis. A goal for species that strives to end extinctions and recover populations of all species that have experienced population declines, and especially those at risk of extinction, would help to align actors towards the transformative actions and interventions needed for humans to live in harmony with nature.

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

The aim of this investigation is focused on the effects of hooked-end steel fibers on both fresh and hardened properties of modified self-compacting concretes (SCC). For this purpose, the steel fibers are associated with other residues contents (i.e. marble, granite and rubber). This concatenated materials contents constitutes a novelty since no investigations are reported. It is found that the increase of rubber content, a better ability to absorb energy is observed. This indicates that a good alternative of structural material is provided. Fresh properties are evaluated by using flow, T500 time, V-funnel, J-ring methods. The mechanical behavior is evaluated in terms of compressive strength, tensile strength, static and dynamic modulus of elasticity, and damping ratio. Experimental results of the water absorption, porosity and density are also attained. It is also found that a SCC mixture containing steel fiber, marble/granite residue and rubber content is a potential mixture to be considered when in SCC designing associated with improved damping ratio. Although the rubber content decreases the mechanical behavior and slump flow, the concatenated utilization of MGR and steel fiber contents provide a slight improve in the damping result. An environmental benefit can also be associated since the cement consumption is decreased with marble additions.

E-waste management (EWM) refers to the operation-management of discarded or unproductive electronic devices and components, a challenge exacerbated due to overindulgent urbanization. This article presents a multidimensional cost-function-based analysis of the EWM framework structured on three modules - environmental, economic, and social uncertainties - which contemplate the 3 pillars of sustainability in an e-waste recycling plant, including the production-delivery-utilization process. The framework incorporates material recovery from a single e-waste facility provisioning for chemical and mechanical recycling. Each module is ranked using independent Machine Learning (ML) protocols: a) Analytical Hierarchical Process (AHP) and b) combined AHP and Principal Component Analysis (PCA). From a long list of possible contributors, the model identifies and ranks two key sustainability contributors to the EWM supply chain: overall energy consumption and volume of carbon dioxide generated. Another key finding is a precise time window for policy resurrection, which for the data considered, happens to be 400-600 days from the start of operation. Another interesting outcome is the quality of prediction using a combination of AHP and PCA, which consistently produced better results than any of these ML methods individually implemented. Model outcomes have been verified using a case study to outline a future E-waste sustained roadmap.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The characteristics of excess aerobic granular sludge, related to its structure and chemical composition, limit the efficiency of anaerobic digestion. For this reason, pre-treatment methods and compositions with other organic substrates are used. The aim of the research was to determine the effects of co-digestion of pre-hydrodynamically cavitated aerobic granular sludge with waste fats on the efficiency of methane fermentation under mesophilic and thermophilic conditions. The addition of waste fats improved the C/N ratio and increased its value to 19. The greatest effects were observed in thermophilic anaerobic digestion at 55°C, where a 15% waste fat content in volatile soilds was ensured. This resulted in the production of 1278.2±40.2 mL/gVS biogas and 889.4±29.7 mL/gVS CH4. The CH4 content of the biogas was 69.6±1.3%. The increase in biogas and CH4 yield compared to pure AGS anaerobic digestion was 34.4% and 40.1%, respectively. An increase in the proportion of waste fats in the substrate had no significant effect on the efficiency of methane fermentation.

The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

New composite with core-shell structure based on magnesium hydride and finely dispersed aluminum powder with aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from composite occurred at the temperature of 117°C. The maximum desorption temperature from the MgH₂-EEWAl composite (10 wt.%) is 336°C compared to pure magnesium hydride – 417°C. The mass content of hydrogen in the composite is 5.5 wt.%. The positive effect of aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. Calculations showed that the activation energy of desorption for the composite is 106±1 kJ/mol, compared with pure magnesium hydride, whose activation energy was 155±2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Rice cultivation is the main agricultural activity in Asia, and it results in an enormous amount of agricultural waste, that are usually disposed-off by burning, causing serious environmental health and climate problems. Pakistan is the tenth largest producer in the world and the fourth exporter of rice in the world. To date, there are no studies targeting Pakistan’s profile monitoring its contribution in open burning emissions from rice straw waste. This study presents the characterization of PCDD/Fs, PCBs and PAHs emissions from three samples of rice straw collected from the main rice cultivation regions of Pakistan (Punjab, Sindh and Azad Jammu and Kashmir) in relation to the role of metal-based agricultural additives. PCDD/Fs, PCBs and PAHs emissions were quantified using a fixed grid system biomass plant and measuring the macro-pollutants online and sampling the organic micro-pollutants and metals in isokinetic mode, followed by ISO and CEN standards methods. In addition, role of agrochemicals was monitored in terms of metal catalysis resulted in POPs emissions. This study provides the characterization of most relevant group of pollutants (metals, PCDD/Fs, PCBs and PAHs) as a result of agricultural waste combustion. The rice straw samples from AJK showed high values of organochlorine micro-pollutants compared to the values followed by samples from Punjab and Sindh, i.e., respectively, ∑PCDD/F (2594>1493>856 pg/Nm³) and ∑PCB (41>38>30 pg/Nm³). Whereas the organic micro-pollutants ∑PAH, indicators of incomplete combustion (PICs), were recorded high in the samples from Sindh followed by Punjab and AJK. This study supports the idea that the phenomena that lead to the formation of PCDD/F and PCB are influenced not only by poor combustion but also by the presence of metal catalysts or precursors in the burned fuel.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

The aim of this study is to examine an efficient and environmental friendly process for hydrolyzing starch, an industrial-derived by-product of the potato processing industry, and to use the produced hydrolysates as substrates for methane production. A full factorial experiment was designed and the optimal concentrations of FeSO4·7H2O, H2O2 and temperature were determined obtaining a yield of 99.5%, with a total carbohydrates content equal to 28.65 g, when the input parameters were at their high level: FeSO4·7H2O 1.00g/L, H2O2 0.51 g/L and temperature 70.0oC. The hydrolysis kinetics were also examined revealing that temperature was the most important factor among the three optimization parameters. Furthermore, biodegradability tests were carried out to measure the methane production potential from the produced hydrolysates. The specific methanogenic activity was reached 0.669 g CODCH4/gVSS-day proving the effectiveness of the hydrolysis process and highlighting the potential of this food manufacturing by-product for bioenergy production. A preliminary cost analysis showed that a small investment for utilizing the starch in an existing wastewater treatment facility of a potato processing industry becomes profitable before the end of the 3rd year obtaining a NPV 37.5% higher than the NPV of the current utilization scenario.

The feasibility of using zeolites, synthesized from components found in municipal solid waste fly ash (MSW-FA), as sorbents for the recovery of nutrients (nitrate and phosphate) and heavy metals is critically assessed in this review. The inherent drawbacks of utilising a highly contaminated, variable, and relatively Al- and Si-dilute source such as MSW-FA to synthesize zeolites are discussed, and different methods to extract and decontaminate zeolite precursor materials from MSW-FA are considered. Ways to synthesize tailored zeolites and how their properties as well as the operational conditions impact the adsorption of cations such as ammonium and heavy metals are summarized. The use of surface-modified zeolites to adsorb nitrate and phosphate is also reviewed. And subsequently, approaches to utilise directly or recover for reuse the adsorbed compounds are considered, discussing potential challenges and mitigating measures related to leaching of unwanted compounds from the zeolites. Moreover, the possibility to regenerate the adsorption capacity of the zeolites for multiple adsorption cycles is considered. In the final chapter of the review a more general discussion of the main challenges and existing research gaps is provided, giving directions for recommended studies.

Bitumen is produced from non-renewable natural resources, continuously deplete and intrigues researchers to look for alternative binders. Annually, tons of waste engine oil (WEO) and crumb rubber (CR) are discarded unsustainably and pose a significant environmental threat. Adding these industrial waste products to asphalt provides a safe and cost-effective way for their disposal and improves the bitumen's performance in parallel. This study uses various combinations of waste engine oil and crumb rubber with 60/70 penetration grade bitumen to produce a partially synthetic bitumen. Adhesion being one of the critical characteristics of the bituminous binder has been assessed using the bitumen bond strength test along with physical and rheological properties. Results showed that waste engine oil with crumb rubber inclusion increases penetration and decreases the softening point, viscosity, complex modulus, and bonding strength. Additionally, polyphosphoric acid (PPA) in smaller dosages was also incorporated into the optimum percentage of CR + WEO to improve the properties of the binder. The results confirm that binder modification with waste engine oil and crumb rubber can be more effective with PPA. It is concluded that 35% of waste can replace the virgin binder giving a cost-effective and environmentally friendly solution.

The decentralized treatment of wastes is studied for an urban scenario considering a high-density population of 2500 inhab./km2. Food and garden waste were assumed to be treated in a co-digestion configuration using several mid-size digesters. In contrast biogas and digestate valorization were carried out in a centralized manner. Electricity and thermal energy were produced from this configuration, accounting for 1.3% of residential electricity demand and 3.2% of thermal demand when using double-turbocharged engines. However, the location of the treatment plants is a factor that may raise social discomfort. Rejection of locating the plant in specific sites close to residential neighbors, nuisance due to possible odor and gaseous emissions, and house market distortions are just a few of a long list of problematic aspects that may threaten the decentralized alternative. These factors are of great relevance and must be given a practical solution if the circular economic model is to be implemented by considering the insertion of waste streams into the production system and generating local energy sources and raw materials.

The extensive utilization of rebar during the construction of the project generates immense rebar waste, leading to increased construction costs and significant greenhouse gas emissions. Various approaches have been explored focusing on the minimization of rebar-cutting waste, such as optimizing cutting patterns, lap splice position, and special-length rebar utilization. Nonetheless, reducing rebar usage by minimizing the number of splices remains uninvestigated. In response to these issues, a two-stage optimization algorithm was developed, prioritizing special-length rebar to achieve near-zero rebar-cutting waste of less than 1% and concurrently reduce rebar usage, thereby promoting sustainable construction practices. The two-stage algorithm presented in this study involves the optimization of the lap splice position for the continuous rebar with a reduction of splices number. Furthermore, it integrates a special-length minimization algorithm for the additional rebars. Applying the algorithm to beam structures in a small-sized factory building project led to a notable reduction of 29.624 tons of rebar, equivalent to 12.31% of the total purchased quantity. Greenhouse gas emissions were reduced by 102.68 tons, and associated costs decreased by USD 30,256. A rebar-cutting waste of 0.99% which is near zero was achieved. These findings highlight the significant potential of the proposed algorithm in reducing rebar waste and facilitating sustainable construction practices. In addition, the application of the proposed algorithm in reinforced concrete construction projects will amplify the associated advantages accordingly.

Brewers’ spent grain (BSG) is an important waste produced in beer companies with a high po-tential to be transformed into commercial by-products. The present paper reports a forecasting technology study with the aid of bibliographic review and patent analysis tools aiming to in-vestigate the maturity of certain technologies, considering the use of BSG on a closed-loop bio-refinery and circular bioeconomy concept integrated into a brewery. To evaluate the possibili-ties of production of high-added value products in Brazil, it was presented an overview of BSG’s scientific, technological, and marketing products and applications. The comparison between numbers of articles versus patents shows that the solutions proposed by research articles are not being transformed into maturated viable technologies. The results suggest that there is a gap between the scientific research in the institutions and their applications in industry, which lead to the destination of the BSG for more economically attractive investments when compared to research in Brazil. Ultimately, from the carried-out analysis, it was possible to propose a brew-ing process connected to the biorefinery system, showing the possibility to the newly arising brewery industries.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

Despite the development of biorefinery processes, so far this area does not take into account the possibility of coupling the “conventional” composting process with the production of biochemicals. However, net carbon monoxide (CO) production has been observed during bio-waste composting. So far, O2 concentration and temperature have been identified as main variables influencing CO formation. This study aimed to investigate the CO net production during bio-waste composting under controlled laboratory conditions, depending on different aeration rates and temperatures. A series of composting processes were carried out in conditions ranging from ~psychrophilic to thermophilic (T=35, 45, 55, and 65°C) and an aeration rate of 2.7, 3.4, 4.8, and 7.8 L‧h-1. The highest concentrations of CO in each thermal variant was achieved with oxygen deficit (aeration rate 2.7 L‧h-1); additionally, CO levels increased with temperature, reaching ~300 ppm at 65°C. Production of CO in mesophilic and thermophilic conditions draws attention to the biological CO formation by microorganisms capable of producing the CODH enzyme. Further research on the CO production efficiency in these thermal ranges is necessary with the characterization of the microbial community and analysis of the ability of the identified bacteria to produce the CODH enzyme and convert CO from CO2.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Over the past few decades, the quantity of construction waste has steadily risen in tandem with the expansion of construction activities and the rapid pace of development and urbanization. This problem is rooted in the practice of delivering materials to construction sites without totally using them for their intended purpose. The primary aim of the JIT tactic is to ensure that the precise materials required for production are available at the precise location, exact time, and appropriate quantity, thereby facilitating timely production. Presently, the use of ready-mix concrete is the most typical instance of a just-in-time construction process Developed countries have benefitted immensely from the use. However, the reverse is the case in developing countries like Nigeria, where indigenous contractors still employ traditional in-situ concreting even when faced with restrictive site space. This study focuses on investigating Ready-mix concrete, to project its immense benefits and effectiveness in minimizing lean construction waste. A survey research design and case study were adopted for this study, with the population being the management staff of construction firms in Lagos State, Nigeria. The questionnaire was used to collect data and the targeted respondents were purposively selected from the population. A total number of 112 questionnaires were administered with a response rate of 51%. Percentage, mean, standard deviation, and ANOVA were used to analyze the data. The mean value is above 3 on a Likert Scale of 5, while faster construction speed and uniform quality of concrete are the topmost benefits derived from adopting Ready-mix Concrete in Nigeria. The Case study also revealed the effectiveness of Ready-mix concrete in minimizing the two lean construction wastes that were examined, namely; waste of overproduction and waste of waiting. It is recommended Just-in-Time technique should be extended to other construction materials aside from concrete to improve waste minimization through the adoption of an overall JIT policy for the construction process.

The Metabolic Food Waste [MFW (kg of food)], first time developed in 2016 as a new indicator by Serafini and Toti, indicates the amount of food consumed over the nutritional requirements and the impact of this overconsumption on the environment. It is necessary to identify the causes and to develop potential methods to prevent and reduce MFW, at the same time with increasing consumer awareness about unsustainable diets and changing diet habits toward more environmentally conscious consumption patterns. By analysing and corroborating external data available for food waste, nutritional requirements, environmental impact of food waste and consumer behaviour, we identified as primary causes for MFW the lack of nutritional education and little understanding of the nutritional requirements amongst all categories of consumers, no access to appropriate food resources or reduced availability of fresh produced food. We conclude that for the quantification of the negative impact of MFW on both the environment and human health, we need a decisive action to raise consumer awareness for healthy and sustainable diets, together with an uniform worldwide distribution of the nutritious food.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

One of the potential sources of rare-earth elements (REEs) is the solid waste from alumina industry - bauxite residue, known as “red mud” (RM). The main REEs from the raw bauxite are concentrated in RM after the Bayer leaching process. The earlier worldwide studies were focused on the scandium (Sc) extraction from RM by concentrated acids to enhance the extraction degree. This leads to the dissolution of major oxides (Fe2O3 and Al2O3) from RM. This article studies the possibility of selective Sc extraction from alkali fusion red mud (RMF) by diluted nitric acid (HNO3) leaching at pH ≥ 2 to prevent co-dissolution of Fe2O3. RMF samples have been analyzed by X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), electron probe microanalysis (EPMA), and inductively coupled plasma mass spectrometry (ICP-MS). Sc extraction has been found to be 71.2 % at RMF leaching by HNO3 at pH=2 and at 80 °C during 90 min. The kinetic analysis of experimental data by the shrinking core model has shown that Sc leaching process is limited by the interfacial diffusion and the diffusion through the product layer. The apparent activation energy (Ea) was 19.5 kJ/mol. We have established that according to EPMA of RMF, Sc is associated with iron minerals; it could act as the product layer. The linear dependence of Sc extraction of magnesium (Mg) extraction has been revealed. This fact indicates that Mg can act as a leaching agent of Sc presented in RMF by ion-exchangeable phase.

A winemaking waste was used as a precursor of activated carbon used in hazardous Cr(VI) removal from solutions. The preparation process consisted of a hydrothermal process, and a chemical activation, of the resulting product, with KOH. The adsorption results showed that the adsorption of Cr(VI) on the obtained activated carbon is strongly dependent on the stirring speed applied to the carbon/solution mixture, pH of the solution, and temperature. The equilibrium isotherm was well fitted to the Langmuir type-II equation, whereas the kinetic can be described by the pseudo-second-order kinetic model. Thermodynamic studies revealed that Cr(VI) adsorption was an exothermic and spontaneous process. Finally, desorption experiments showed that Cr(VI) was effectively desorbed using hydrazine sulfate solutions, and at the same time, the element was reduced to the less hazardous Cr(III) oxidation state.

One way to increase overall natural gas engine efficiency is to transform exhaust waste heat into useful energy by means of a bottoming cycle. Organic Rankine cycle (ORC) is a promising technology to convert medium and low grade waste heat into mechanical power and electricity. This paper presents an energy and exergy analysis of three ORC-Waste heat recovery configurations by using an intermediate thermal oil circuit: Simple ORC (SORC), ORC with Recuperator (RORC) and ORC with Double Pressure (DORC), and Cyclohexane, Toluene and Acetone have been proposed as working fluids. An energy and exergy thermodynamic model is proposed to evaluate each configuration performance, while available exhaust thermal energy variation under different engine loads was determined through an experimentally validated mathematical model. Additionally, the effect of evaportating pressure on net power output , absolute thermal efficiency increase, absolute specific fuel consumption decrease, overall energy conversion efficiency, and component exergy destruction is also investigated. Results evidence an improvement in operational performance for heat recovery through RORC with Toluene at an evaporation pressure of 3.4 MPa, achieving 146.25 kW of net power output, 11.58% of overall conversion efficiency, 28.4% of ORC thermal efficiency, and an specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas Flow, 1.784 lambda, and 1758.77 kW mechanical engine power.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

Efficient use of agricultural wastes and by-products, basically transforming waste materials into value added products, is considered as pivotal for an effective bioeconomy strategy for the rural development. To this scope, citrus waste management represents a major issue for citrus processors but, at the same time, it embodies a potentially unexploited resource for the rural sustainable development. This study focuses on analyzing the current management of citrus waste in South Italy and identifying the determinants and barriers that may affect an entrepreneur’s choice on the destination of citrus waste. Citrus processors’ preferences about the contract characteristics needed to take part in a co-investment scheme have been investigated. Both analyses are preliminary steps to design an innovative and sustainable citrus by-product supply chain. Results show that the distance between the citrus processors and the citrus by-products plant is one of the main criteria for choosing alternative valorization pathways. Moreover, the required guaranteed capital, the short duration of the contract, and low risk are contract scheme characteristics that improve entrepreneurs’ willingness to co-invest in the development of a citrus waste multifunctional plant.

DR2B and DR2C extracts, from peel of commercially and physiologically ripe eggplants, were studied for the antioxidative cytoprotective properties and anti-HSV-1 activity, in line with the evidence that several antioxidants can impair viral replication by maintaining reducing conditions into the host cells. The antioxidative cytoprotective effects against tBOOH-induced damage was assessed in Caco2 cells, while the antiviral activity was studied in Vero cells; phenolic and anthocyanin fingerprint was characterized by integrated phytochemical methods. Results highlighted different compositions of the extracts, with chlorogenic acid and delphinidin-3-rutinoside as the major constituents; other peculiar phytochemicals were also identified. DR2C resulted able to partly counteract the tBOOH-induced cytotoxicity, with a remarkable lowering of lactate metabolism under both normoxia and hypoxia. DR2B and DR2C reduced ROS production, possessed scavenging and chelating properties. Interestingly, DR2C increased intracellular GSH levels. Furthermore, DR2C inhibited the HSV-1 replication when added for 24 h after viral adsorption, as also confirmed by the reduction of many viral proteins expression. Since DR2C was able to reduce NOX4 expression during HSV-1 infection, its antiviral activity may be correlated to its antioxidant properties. Although further studies are needed to better characterize DR2C activity, the results suggest this extract as a promising new anti-HSV-1 agent.

The efficiency of cold steel rolling depends mainly on the quality of the metal-working coolant (MWC) and its cost. In this connection, it is actual to search for new compositions of lubricants and emulsions, which provide the lowest values of the friction coefficients in deformation zone and are obtained by waste recycling in other industries. In this study we have developed new compositions of the MWC on basis of mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The new compositions of MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 100 mm. The efficiency of new MWC during cold rolling of brass L63 samples was determined by factor of metal stretch forming λ. We found the new metal-working coolants to show the most efficiency under higher cobbing that provides the highest metal stretch forming. The composition with 30 % of mono- and diglycerides is the most effective because it provides the minimum coefficient of friction that leads to increase of factor of metal stretch forming. Thereby the metal-working coolants on basis of mono- and diglycerides obtained from the wastes of sunflower oil production can be recommended for use in strip rolling of copper-zinc alloys because of a low cost, availability and high efficiency.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

The textbook analysis of vacuum energy density (VED) in flat spacetime follows from Pauli’s lectures of 1951, in which quantum vacuum is modeled as a reservoir of free harmonic oscillators. In his lectures, Pauli shows that deriving a nearly vanishing VED is contingent upon fulfilling three corollary conditions called polynomial-in-mass-constraints. The goal of this work is to evaluate Pauli’s constraints against the Standard Model parameters and the Higgs mechanism of spontaneous symmetry breaking.

This paper presents an optimal design for the inner current control loop of the continuous current conduction mode (CCM) power factor correction (PFC) stage, which it can be used as the front stage of the two stages alternating current-direct current (AC-DC) telecom power supply. Conventional single-phase CCM-PFC boost converter usually implemented with using of the proportional-integral (PI) controllers in both of the voltage and current control loops, to regulate the output DC voltage to the specified value, moreover to maintains the input current follows the input voltage which offers converter with high power factor (P.F) and low current total harmonic distortion (THD). However, due to the slow dynamic response of the PI controller at the zero-crossing point of the input supply current, input current can’t fully follow the input voltage which leads to high THD. Digitally controlled PFC converter with an optimal design of the inner current control loop using doubly control loops IP controller to reduce the THD and to offer input current with unity P.F was performed in this paper. Furthermore, for the economic design of the digitally control PFC converter, two isolated AC and DC voltage sensors are proposed and designed for the interfacing with the microcontroller unit (MCU). PSIM software was used to test the converter performance with using the proposed designed current controllers and isolated voltage sensors. High power density digitally controlled telecom PFC stage with P.F of about 99.93%, full load efficiency of about 98.70% and THD less 5.50% is achieved in this work.

Molecule radiation can be used as a tool to study colder regions in switching arc plasmas like arc fringes in contact to walls and ranges around current zero (CZ). This is demonstrated in the present study for the first time for the case of ablation-dominated high–current arcs as key elements of self–blast circuit breakers. The arc in a model circuit breaker (MCB) in CO2 with and an arc in a long nozzle under ambient conditions with peak currents between 5 and 10 kA were studied by emission and absorption spectroscopy in the visible spectral range. The nozzle material was polytetrafluoroethylene (PTFE) in both cases. Imaging spectroscopy was carried out either with high-speed cameras or with intensified CCD cameras. A pulsed high-intensity Xe lamp was applied as background radiator for the broad-band absorption spectroscopy. Emission of Swan bands from carbon dimers was observed at the edge of nozzles only or across the whole nozzle radius with highest intensity in the arc center, depending on current and nozzle geometry. Furthermore, absorption of C2 Swan bands and CuF bands were found with the arc plasma serving as background radiator. After CZ, only CuF was detected in absorption experiments.

The move to a low carbon economy is very important for enhancing international competitiveness. The eco-innovation is the critical factor of the green paradigm. This study is designed to investigate deeply the determinants of eco-innovation of manufacturing firms in Korea by suggesting anticipated regulations, self-regulations, and industry-specific characteristics as external factors and open information sources as internal factors. The data used in the analysis is 1946 sample firms from Korean Innovation Survey 2010 based on the Oslo Manual. Using the multi-variate probit analysis and the zero-inflated negative binomial (ZINB) regression analysis, we have found out that the anticipated regulations and self-regulations have significant influences both on eco-process innovation and eco-product innovation, while industrial characteristics have no effects. The empirical results also show that the breadth of information sources has a positive effect on businesses in implementing eco-innovations. Our findings show that the Korean government should provide a good platform where firms can better understand the future trends of environmental policies, particularly policies on anticipated and self-regulations. At the same time, Korean firms should establish a voluntary system to control environmental activities so that they can improve eco-innovations through integrating external information.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The circular economy is one of the main strategies for mitigating the environmental impacts of civil construction, due to the generation of construction and demolition waste (CDW). In this transition, evaluating alternatives for using buildings as material banks is a way to make the process of reusing construction components more efficient. Thus, the article aimed to evaluate the state of the art of publications on the relationship between the circular economy in civil construction and the conceptual model of buildings as material banks, to mitigate the environmental impacts of CDW. The authors chose the methodological design of Systematic Literature Review, using the Scopus and Web of Science databases for research, with the following search strings: ("construction" or "civil construction" or "built environment" or "construction industry" ) and ("circular economy" or "circular construction") and ("material banks" or "BAMB" or "buildings as material banks" or "building stocks" or "building materials") and ("construction waste" or "demolition waste" or "CDW" or "construction and demolition waste" or "environmental impacts"). After a screening in which only articles published in journals were selected, from 2013 to 2023, inclusion and exclusion criteria were applied, to evaluate only those that had a direct relationship with CDW management through circular economy strategies and buildings such as banks of material. As a result, 93 articles remained, which were analyzed using quantitative and qualitative approach. The quantitative results showed an increase in publications since 2020, which are concentrated in European countries and China. The predominance of applied studies was also noted, through case studies that evaluate the management of materials and waste in the urban environment. The qualitative analysis, carried out using a SWOT Matrix, highlighted the strengths of the buildings, such as material banks, the potential reduction of resource extraction and urban mining, promoting the circulation of construction products. However, the recycling of waste, such as aggregates, still stands out as the main end-of-life strategy adopted, even without occupying the top of the waste hierarchy.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

Involving industrial waste into economic circulation, in particular flotation waste from coal enrichment, is an urgent task. The coal preparation waste of ArcelorMittal Temirtau JSC was studied with a view to the possibility of using it as an alternative substitute for coke breeze in the sintering process. During a thermoanalytical study on a synchronous thermal analyzer STA 449 NETZSCH in dynamic mode with a heating rate of 10, 20, 30 °C/min in an air flow of 30 cm³/min in the temperature range 30–1000 °C, we determined the lower heat of combustion of carbon-containing material, change mass during calcination, change and rate of change in the mass of the sample, thermal effect of the process, the temperature of the beginning, end and maximum development of thermal effects. It has been established that the greatest mass loss is observed in the temperature range 580 °C- 610 °C, which is about 65–67% of the total mass of the organic component of coal. The maximum burnout rate corresponds to a temperature of 540–563 °C. The lowest calorific value of the studied waste was 15.9 MJ/kg. The results of thermal analytical research and technical analysis substantiate the possibility of using flotation waste in a mixture of up to 10% with coke breeze for combustion in the sintering layer for the production of sinter. Analysis of the composition of flotation waste showed that they have a high specific surface area (56.8∙10³ m²/kg), are highly dispersible, soggy, and capable of swelling, and the predominant amount of clay substance makes them a plastic material. The possibilities of using coal flotation waste as an alternative substitute for coke breeze have been studied after the regimes of its preparation for sintering have been developed and a rational regime of layer-by-layer combustion in the sintering layer has been established. The optimal ratio of coke and OPC in the fuel mixture of the sintering charge was determined.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Printed circuit boards (PCBs) make up 3 to 5% of all electronic waste. The metal content of spent PCBs can reach 40%. They usually contain valuable metals - Ag, Au, Pd, as well as other metals such as Cu, Sn, Pb, Cd, Cr, Zn, Ni and Mn. However metallic part of whole PCB is 40-60% including Cu layers between the fiberglass-polymer layers. The paper describes economics of the the valuable metals (Ag, Au, Pd) containing concentrate preparation from raw PCB. Considered the influence of pre-treatment method of PCB before the extraction of valuable metals on the extraction self-cost change. The disintegration method is based on the high-energy impact of the particles of the material to be ground, thus causing the separation of the metallic components of the PCB. In the course of the work, single and double direct grinding by the method of disintegration was studied. For the calculation the test batch 10’000 kg of two types of PCB were taken for estimation of the self costs and potential profit in case of complete valuable metals (Ag, Au, Pd) plus Cu extraction. Is shown that from 10’000 kg of studied PCB is possible to obtain 1144 and 1644 kg of metal-rich concentrate, which further should be subjected to electro-hydrochlorination for metals leaching. The main findings shows, that despite of high content of Cu in studied PCB, the commercial value is insignificant in total income from the Ag, Au and Pd sale. Was established correlation of the self-cost decrease after separative disintegration of PCB by metal content increase (by specific metals such as Au, Ag, Pd and also Cu) with the metal potential yield after extraction.

The Indorama Eleme Petrochemical Limited (IEPL) is found in the southern part of Nigeria more specifically on the Rivers State southern religion Nigeria. It consists of five distinct units, each of which generates its own unique trash at a rate of around 3115.98 tonnes per year. This study had the goal of concentrating on the management of the processing wastes in order to minimize the negative effects that they have on the environment. It is necessary to have an understanding of the number, nature, and make-up of IEPL's industrial wastes in order to effectively manage and regulate the development of waste there. As a result, we decided to collect data through the use of questionnaires. The classification of industrial wastes was accomplished by doing a comparative study and synthesis of research that were relevant to the management of petrochemical waste. Because an individual coding system is required for the integrated management of industrial waste, we gave each type of trash a code that consists of thirteen digits. The primary components of trash were catalysts (9.58 percent), metallic materials (7.62 percent), plastic barrels (35.77 percent), coke (12.66 percent), wood (4.47%), oil (4.15%), glass (0.028 percent), cooling tower packaging (6.7 percent), and other material (18.83 percent). According to the findings of the investigation into the physical qualities of the wastes, only 11.81% of these residues were liquid, while 88.19% were solid. The current handling of these wastes has been experiencing significant difficulties as of late. garbage management at IEPL was particularly challenging due to the wide variety of wastes produced there and the dangerous nature of the wastes themselves (88.19% of garbage was hazardous waste). Recycling and reuse of garbage may have been the greatest decision in some situations; yet, incineration and disposal of waste are also necessary options.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

The Atlantic cod (Gadus morhua) and red king crab (Paralithodes camtschaticus) processing wastes are massive and unutilized in the Murmansk region of Russia. The samples of skin-containing waste of Atlantic cod fillets production were hydrolyzed using enzyme preparations derived from red king crab hepatopancreases, porcine pancreases and Bacillus subtilis bacteria. The activity of enzymes from crab hepatopancreases was significantly higher than the activity of enzymes derived from other sources. The optimal conditions of the hydrolysis process have been figured out. The samples of cod processing waste hydrolysate were analyzed for amino acid composition and molecular weight distribution. The samples of hydrolysate were used as core components for bacterial culture medium samples. The efficiency of the medium samples was tested for Escherichia coli growth rate; the most efficient sample had efficiency 95.3% of that of a commercially available medium based on fish meal. Substitution of medium components with those derived from industrial by-products is one of the ways to decrease a cost of a culture medium in biopharmaceutical drug production.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

The use of natural stone has a historical and environmental value that makes it strategically valuable for landscape conservation in Europe. Marble, among others, is widely spread on Earth, and it offers high-performance features in architectural applications. However, the complexity of these formations and the rock variability in different ore bodies require detailed studies of the natural and induced stress state, the fracturing degree, and the influence of external factor (such as temperature and/or chemical agents) on the mechanical properties in order to optimize the exploitation processes by reducing extractive waste. This article shows a series of studies conducted by the authors over the last 20 years aimed at making the exploitation of marble blocks in the Carrara basin safer, more efficient, and, therefore, more sustainable. In particular, studies for increasing the knowledge on the natural and the induced stress state through on-site measurements and numerical modeling, studies to improve the quality of the exploited material through improvements of cutting technologies, studies to improve the knowledge of the mechanical behavior of the material under varying loads and temperature conditions and studies to improve the reuse of water materials and their reduction are reported.

Relying on the United Arab Emirates (UAE) extract from the cross-national data sample on the environmental affection and cognition of adolescent students, and seemingly unrelated bivariate weighted ordered probit regression modeling, this study adopts a national perspective to investigate the determinants of adolescent students' awareness and expectations about nuclear power technology and nuclear waste in the UAE. Identification of model parameters is achieved through maximum simulated likelihood estimation. The findings show that each level increase in UAE youth's interest in ecosystem services and sustainability raises their awareness of nuclear electrical power and nuclear waste by 13.5%, while reducing by 2.4% their level of optimism towards the technology. Furthermore, we find significant heterogeneity in youth awareness and expectations about nuclear power technology across the seven Emirates. Accounting for all other factors (including interest in ecosystem services), UAE youth awareness about nuclear electrical power technology appears to not significantly influence their expectations about the evolution of this technology for the next 20 years. Given that the UAE first nuclear power plant ``Barakah'' is scheduled to start operations end of 2019 beginning 2020, and the typical long life-span of nuclear wastes, our results provide important insights for developing sustainable nuclear energy policies and establishing a long-term nuclear energy program in the UAE.