Hydrogen peroxide is an important chemical of increasing demand in today’s world. Currently, the anthraquinone autoxidation process dominates the industrial production of hydrogen peroxide. Herein, hydrogen and oxygen are reacted indirectly in the presence of quinones to yield hydrogen peroxide. Owing to the complexity and multi-step nature of the process, it is advantageous to replace the process with an easier and straightforward one. The direct synthesis of hydrogen peroxide from its constituent reagents is an effective and clean route to achieve this goal. Factors such as water formation due to thermodynamics, explosion risk, and the stability of the hydrogen peroxide produced hinder the applicability of this process at an industrial level. Currently, the catalysis for the direct synthesis reaction is palladium based and the research into finding an effective and active catalyst has been ongoing for more than a century now. Palladium in its pure form, or alloyed with certain metals are some of the new generation of catalysts that are extensively researched. Additionally, to prevent the decomposition of hydrogen peroxide to water, the process is stabilised by adding certain promoters such as mineral acids and halides. A major part of today’s research in this field focusses on the reactor and the mode of operation required for synthesising hydrogen peroxide. The emergence of microreactor technology has helped in setting up this synthesis in a continuous mode, which could possibly replace the anthraquinone process in the near future. This review will focus on the recent findings of the scientific community in terms of reaction engineering, catalyst and reactor design in the direct synthesis of hydrogen peroxide.

High porosity and mass transport properties of microfiltration polymeric membranes benefits nutrients supply to cells when used as scaffolds in interstitial perfusion bioreactors for tissue engineering. High nutrients transport is assumed when pore size and porosity of the membrane are in the micrometric range. The present work demonstrates that the study of membrane fouling by proteins present in the culture medium, though not done usually, should be included in the routine testing of new polymer membranes for this intended application. Two poly(ε-caprolactone) microfiltration membranes presenting similar average pore size (~0.7µm) and porosity (>80%) but different external surface porosity and pore size have been selected as case study. The present work demonstrates that a membrane with lower surface pore abundance and smaller external pore size (~0.67 µm), combined with adequate hydrodynamics and tangential flow filtration mode is usually more convenient to guarantee high flux of nutrients. On the contrary, having large external pore size (~1.70µm) and surface porosity would incur in important internal protein fouling that could not been prevented with the operation mode and hydrodynamics of the perfusion system. Additionally, the use of glycerol in the drying protocols of the membranes might cause plasticization and a consequent reduction of mass transport properties due to membrane compaction by the pressure exerted to force perfusion. Therefore, preferentially, drying protocols that omit the use of plasticizing agents are recommended.

The dynamic development of electromobility poses challenges to designers regarding not only the efficiency of energy transformation but also the battery life, which is influenced by the stability of its operating temperature. Designing cooling systems is connected not only with the optimization of energy management but also with other environmental parameters, such as noise emission. The paper presents the numerical optimization of an innovative radiator for use in electric buses in terms of energy consumption and noise emission. The results of the numerical studies were verified in laboratory and field conditions, showing a very good convergence of the model with the results of the experiments.

This primer provides an overview of the rapidly evolving field of generative artificial intelligence, specifically focusing on large language models like ChatGPT (OpenAI) and Bard (Google). Large language models have demonstrated unprecedented capabilities in responding to natural language prompts. The aim of this primer is to demystify the underlying theory and architecture of large language models, providing intuitive explanations for a broader audience. Learners seeking to gain insight into the technical underpinnings of large language models must sift through rapidly growing and fragmented literature on the topic. This primer brings all the main concepts into a single digestible document. Topics covered include text tokenization, vocabulary construction, token embedding, context embedding with attention mechanisms, artificial neural networks, and objective functions in model training. The primer also explores state-of-the-art methods in training large language models to generalize on specific applications and to align with human intentions. Finally, an introduction to the concept of prompt engineering highlights the importance of effective human-machine interaction through natural language in harnessing the full potential of artificial intelligence chatbots. This comprehensive yet accessible primer will benefit students and researchers seeking foundational knowledge and a deeper understanding of the inner workings of existing and emerging artificial intelligence models. The author hopes that the primer will encourage further responsible innovation and informed discussions about these increasingly powerful tools.

Background: COVID-19 has impacted Indian engineering institutions (EIs) enormously. It has tightened its knot around EIs that forced their previous half-shut shades completely down to prevent the risk of spreading COVID-19. In such a situation, fetching new enrollments on EI campuses is a difficult and challenging task, as students’ behavior and family preferences have changed drastically due to mental stress and emotions attached to them. Historically, during crisis situations, institutions have struggled to return to the normal track. Consequently, it becomes a prerequisite to examine the choice characteristics influencing the selection of EI during the COVID-19 pandemic to make it ‘normal’ for ‘new’ enrollments. The purpose of this study is to critically examine choice characteristics that affect students’ choice for EI and consequently to explore relationships between institutions’ characteristics and the suitability of EI during the COVID-19 pandemic across students’ characteristics. Quantitative research, conducted through a self-reported survey composed of a closed-ended structured questionnaire, was purposefully incorporated into the students who recently were enrolled in EIs (batch years 2020-2021) belonging to the North Maharashtra region of India. Results:The findings of this study revealed dissimilarities across students’ characteristics regarding the suitability of EIs under pandemic conditions. Regression analysis revealed that EI characteristics such as proximity, image and reputation, quality education and curriculum delivery have significantly contributed to suitability under COVID-19. At the micro level, multiple relationships were noted between EI characteristics and the suitability of EI under the pandemic across students’ characteristics. Conclusion:Bringing ‘normality’ to ‘new’ enrollments totally depends on EI’s resilience in meeting the needs of diversity in the COVID-19 pandemic situation, which repositions themselves to govern student-centric strategies instituted for the overall suitability of EI under pandemic conditions. The study has successfully demonstrated how choice characteristics can be executed to regulate the ‘suitability’ of EI under the COVID-19 pandemic for the inclusion of diversity. It is useful for policy makers and academicians to reposition EIs that fetch diversity during the pandemic. This study is the first to provide insights into the performance of choice characteristics and their relationship with the suitability of EIs under a pandemic and can be a yardstick in administering new enrollments.

Building Information Modelling (BIM) has been more popular in the construction industry as a consequence of the many advantages it offers, such as increased productivity, improved project outcomes, and reduced expenses. However, there are many obstacles that must be overcome before BIM can be widely used. This research uses a poll of construction industry experts to investigate the challenges associated with using BIM in projects. Cost of implementation, inadequate standards and procedures, and a lack of knowledge with BIM were some of the hurdles that were measured in the study. Statistical techniques were used to examine the data, and the findings indicate that the high cost of implementation and the absence of sufficient standards and procedures are the two main obstacles to the widespread adoption of BIM. Problems with supply chain management and a lack of experience with BIM are also mentioned as obstacles. The report also suggests solutions, such as a more focused teaching effort on BIM-related issues and the creation of a specialised BIM curriculum. Professionals in the construction industry may utilise the study’s results to their advantage by expanding their knowledge of the obstacles standing in the way of widespread adoption of BIM.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

The occurrence of bone-related disorders and diseases has increased dramatically in recent years around the world. Demineralized bone matrix (DBM) has been widely used as a bone implant due to its osteoinduction and bioactivity. However, the use of DBM is limited because it is a particulate material, which makes it difficult to manipulate and implant with precision, in addition, these particles are susceptible to migrate to other sites. To address this situation, DBM is commonly incorporated into a variety of carriers. An injectable scaffold has advantages over bone grafts or preformed scaffolds, such as the ability to flow and fill the bone defect. The aim of this research is to develop a DBM carrier with such viscoelastic properties to obtain an injectable bone substitute (IBS). The DBM carrier developed consisted of a PVA/glycerol network cross-linked with borax and reinforced with CaCO3 as a pH neutralizer, porosity generator, and source of Ca. The physicochemical properties were determined by the injectability test, FTIR, SEM, and TGA. Porosity, degradation, bioactivity, possible cytotoxic effect, and proliferation in osteoblasts were also determined. The results show that the developed material has great potential to be used in bone tissue regeneration

The treatment of large-area bone defects remains a challenge; however, various strategies have been developed to improve the performances of scaffolds in bone tissue engineering. In this study, poly(lactide-co-glycolide)/hydroxyapatite (PLGA/HA) scaffold was coated with Asp-Gly-Glu-Ala (DGEA)-incorporated collagen for the repair of rat skull defect. Our results indicated that the mechanical strength and hydrophilicity of PLGA/HA scaffold were clearly improved and conducive to cell adhesion and proliferation. The collagen-coated scaffold with DGEA significantly promoted the repair of skull defect. These findings indicated that a combination of collagen coating and DGEA improved scaffold properties for bone regeneration, thereby providing a new potential strategy for scaffold design.

This comprehensive study delves into the implementation and effectiveness of the flipped classroom model in engineering EMI (English as a Medium of Instruction) courses in Taiwan. Situated within the strategic framework of Taiwan's Bilingual Nation 2023 policy, this research aims to enhance the global competitiveness of Taiwan's semiconducting manufacturing engineering sector. The study’s primary focus is on understanding the perceptions and learning outcomes of EFL (English as a Foreign Language) students in engineering courses. Through a methodical approach using descriptive statistics and chi-square tests, the study analyzes data from 33 junior engineering students specializing in mechanical and mechatronic fields. The findings highlight a significant positive influence of the flipped classroom model on various aspects of student learning, including increased engagement, heightened creativity, and enhanced problem-solving skills. Additionally, the study emphasizes the critical role of timely L1 support in facilitating effective learning in EMI settings. These outcomes not only demonstrate the flipped classroom's viability as a sustainable educational approach but also provide crucial insights for educators and policymakers. By aligning cutting-edge teaching methods with the evolving needs of engineering education, this study contributes to the discourse on educational innovation. It ultimately guides the development of future engineering programs that cater to diverse student needs and fosters the cultivation of skilled engineering professionals.

The main goal of the research is to assess the effectiveness of aerial ground-penetrating radar (GPR) in delineating boundaries between disturbed clayey ground and rock formations along the old Wadi. The study also tackles technical challenges associated with drone-based GPR applications in urban open areas, considering geological heterogeneity, topographic variations, and environmental conditions. The potential of using drone-based GPR equipped with an unshielded dipole antenna as a transformative tool in geospatial analysis was demonstrated. The research encompasses academic insights and field borehole drilling experiments to validate the accuracy and reliability of drone-based GPR data in real-world scenarios. Anticipated contributions include advancements in understanding drone-based GPR technology for mapping disturbed soil boundaries in foundation engineering applications and other relevant areas and recommendations for optimizing its performance in challenging terrains.

Bacteriotherapy is emerging as a strategic and effective approach to treat infections by providing putatively harmless bacteria (i.e., probiotics) as antagonists to pathogens. A proper delivery of probiotics or their metabolites (i.e., post-biotics) can avail itself of biomaterial encapsulation by innovative manufacturing technologies. This review paper aims at providing the most recent biomaterial-assisted strategies proposed to treat infections or disbiosis using bacteriotherapy. We revised the encapsulation processes across multiscale biomaterial approaches, which could be ideal to target different tissues and suit diverse therapeutic opportunities. Hydrogels, and in particular polysaccharides, are the focus of this review, as they have been reported to better sustain vitality of the live cells incorporated. Specifically, the approaches for fabricating hydrogel-based devices with increasing dimensionality (D), namely, 0D (i.e., particles), 1D (i.e., fibers), 2D (i.e., fiber meshes), and 3D (i.e., scaffolds) endowed with probiotics, were detailed by describing their advantages and challenges, along with a future overlook in the field. Electrospinning, electrospray and 3D bioprinting were investigated as new biofabrication methods for probiotic encapsulation within multidimensional matrices. Finally, examples of biomaterial-based systems for cell and post-biotic release were reported.

Evaluating mutation testing behavior can help decide whether refactoring successfully maintains the expected initial test results. Moreover, manually performing this analytical work is both time-consuming and prone to errors. This paper extends an approach to assess test code behavior and proposes a tool called MeteoR. This tool comprises an IDE plugin to detect issues that may arise during test code refactoring, reducing the effort required to perform evaluations. A preliminary assessment was conducted to validate the tool and ensure the proposed test code refactoring approach is adequate. By analyzing not only the mutation score but also the generated mutants in the pre- and post-refactoring process, results show that the approach is capable of checking whether the behavior of the mutants remains unchanged throughout the refactoring process. This proposal represents one more step toward the practice of test code refactoring. It can improve overall software quality, allowing developers and testers to safely refactor the test code in a scalable and automated way.

Hydrogels prepared from natural polymer have attracted extensive attentions in biomedical fields such as drug delivery, wound healing, and regenerative medicine due to their good biocompatibility, degradability and flexibility. This review outlines the commonly used natural polymer in hydrogel preparation, including cellulose, chitosan, collagen/gelatin, alginate, hyaluronic acid and starch. The polymeric structure and process/synthesis of natural polymers are illustrated, and natural polymer-based hydrogels including the hydrogel formation and properties are elaborated. Subsequently, the biomedical application of hydrogels based on natural polymer in drug delivery, tissue regeneration, wound healing and other biomedical field is summarized. Finally, the future perspectives of natural polymers and hydrogels based on them are discussed. For natural polymer, novel technologies such as enzymatic and biological methods are developed to improve the structural properties and the development of new natural based polymers or natural polymer derivatives with high performance is still very important and challenging. For natural polymer-based hydrogels, novel hydrogel materials, like double-network hydrogel, multifunctional composite hydrogels and hydrogel microrobots are designed to meet the advanced requirements in biomedical application, and new strategies such as dual-crosslinking, microfluidic chip, micropatterning and 3D/4D bioprinting, have been explored to fabricate advanced hydrogel materials with designed properties for biomedical application. Overall, natural polymeric hydrogels have attracted increasing interests in biomedical application, and the development of novel natural polymer-based materials and new strategies/methods for hydrogel fabrication is badly desirable and still challenging.

The aerospace industry demands high-performance materials that can withstand extreme conditions and maintain efficiency in a variety of applications. Bio-inspired polymer coatings have emerged as a promising approach to meet these demands, by drawing inspiration from natural systems to develop new coatings that exhibit enhanced properties, such as self-cleaning, anti-icing, thermal management, and corrosion resistance. In this review, recent developments in the field of bio-inspired polymer coatings for aerospace applications are presented, covering a range of coatings and their respective properties. We discuss the recent developments and applications of bio-inspired coatings, with a focus on their advantages and challenges in aerospace applications. We also highlight the potential for future research and development in this field, including the integration of advanced technologies such as nanotechnology and additive manufacturing. The review aims to provide insights into the current state-of-the-art of bio-inspired polymer coatings for aerospace applications and to inspire further research in this rapidly growing field.

Hydrogels (gels) are attractive tools for tissue engineering and regenerative medicine due to their potential for drug delivery and ECM-like composition. In this study, we use rheology to characterize GelMA/alginate gels loaded with human platelet lysate (PL). We then characterize these gels from a physicochemical perspective and evaluate their ability to transport PL proteins, their pore size, and their rate of degradation. Finally, their biocompatibility is evaluated. We describe how alginate changes the mechanical behavior of the gels from elastic to viscoelastic after ionic (calcium-mediated) crosslinking. In addition, we positively report the release of PL proteins and relate it to the degradation profile of the gels and the biocompatibility of the gels. Thus, the developed gels represent attractive substrates for both cell studies and bioactive materials.

Development of bioresponsive extrudable hydrogels for 3D bioprinting is imperative to address the growing demand for scaffold design and efficient and reliable methods of tissue engineering and regenerative medicine. This study proposed genipin-crosslinked gelatin-hyaluronic acid hydrogel bioink with different amounts of gelatin tailored for 3D bioprinting, focusing on high cell density loading and less artificial extra-cellular matrix (ECM) effect, as well as exploring their potential applications in tissue engineering. The bioresponsiveness of these hydrogel scaffolds was successfully evaluated in different physiological conditions. 3D and four-axis printing of complex structures such as shapes of hollow tube, star, pyramid, and four-axis tubular scaffolds prove the hydrogel’s high extrusion ability and post-printing shape fidelity. Cytocompatibility and high cell density 3D bioprinting using this moderately stable hydrogel exhibit high potential for precise cell-delivery modes in tissue engineering as well as regenerative medicine.

Product assembly is usually one of the last steps in the entire production process. This activity is typically entrusted to assembly workers because it is generally not possible to automate every type of product. For complex products, assembly can take a long time until the fitter learns the procedure and is able to assemble the product on his own. This contribution presents a cus-tom-developed system that enables controlled assembly of the extruder and can be used for complex and diverse products. The system serves to guide the fitter precisely and shows him which part to use at which time. The proposed system will show and describe on the display all necessary assembly steps and parts. Two-step verification is used to ensure that the correct part is picked from the stack. The contribution is supported by the implementation of a case study in a small company with a sample of 30 employees, which demonstrates that the proposed system shortens the extruder assembly time and significantly reduces the error rate. The presented solution is scalable and flexible, as it can be easily adapted to display the assembly steps of another product.

The main objective of this work is the design and implementation of self-adaptive capabilities in wireless sensors by applying control engineering and model-based design methodologies. It has been addressed the problem related to the changes in the flow of data packets through the network connection and the excess energy consumption that this causes in these devices. To design the solution, a systemic characterization of the scheduling and execution process of embedded tasks on the device has been carried out. This means defining cause-effect relationships in the system and its modelling theoretically and/or experimentally. In turn, these models facilitate the design of control strategies to improve the dynamic behavior of the system. As a solution, a self-adaptation strategy based on feedforward control algorithm has been designed and developed, which has been applied to improve the dynamic behavior and resource consumption. The developed solution has been satisfactorily evaluated experimentally.

There are various biomaterials in nature, but none fulfills all the requirements. Cellulose, eco-friendly material-based biopolymers, have been advanced biomedicine to satisfy most market demand and circumvent many ecological concerns. This review aims to present an overview of the state of the art in cellulose's knowledge and technical biomedical applications. It included an extensive bibliography of recent research findings for fundamental and applied investigations. The chemical structure of cellulose allows modifications and simple conjugation with several materials, including nanoparticles, without tedious efforts. Cellulose-based materials were used for biomedicine applications such as antibacterial agents, antifouling, wound healing, drug delivery, tissue engineering, and bone regeneration. They advanced the applications to be cheap, biocompatible, biodegradable, easy for shaping and processing into different forms, with suitable chemical, mechanical and physical properties.

Cases of road cave-ins have been reportedly increasing globally and reports have associated this phenomenon to underground soil erosion due to defective sewer pipes. As the sewer pipes age, they may develop some defects which may lead to cracks and crevices that will lead to infiltration of the soils surrounding the pipe into the pipe, leading to the formation of cavities around the pipe. Therefore, this study investigated the factors behind the causes of underground soil erosion due to defective sewer pipes and proffered solutions for combating underground soil erosion due to defective sewer pipes. The study objective included; (a) establishing how the soil particle sizes affect the internal soil erosion due to defective sewer pipes, (b) determination of the effect of defect sizes on the internal soil erosion due to defective sewer pipes, (c) establishing the effect of the embedment material used on the internal soil erosion due to defective sewer pipes, (d) investigation of the type of soil erosion mechanism in the presence of a buried sewer pipe defect caused by the groundwater infiltration process. The methodology of the study involved reviewing and analyzing secondary qualitative and quantitative data. The findings established that the defect size of the pipe, the type and characteristics of the soil and the type of embedment materials used affected erosion of soil around a defective sewer pipe.

Metabolite transport across cellular membranes is a key feature of living organisms. Specialized proteins or protein complexes mediate such transport processes and are accessible to genetic engineering approaches. This special issue will reflect on the different transport between cellular compartments. It will provide an overview about different transporter classes and metabolic engineering approaches in different organisms ranging from Bacteria to Eukarya. The transport mechanisms energetics of these compounds were thought little of, and most consideration was given to the designing of metabolic pathways. Gram-negative microbes discharge a wide scope of proteins whose capacities incorporate biogenesis of organelles, for example, pilli and flagella, supplement securing, destructiveness, and efflux of medications and different poisons. Six particular emission frameworks have been appeared to intervene protein send out through the inward and external layers of Gram-negative microbes. These pathways are exceptionally monitored all through the Gram-negative bacterial species. In Gram-positive microscopic organisms, discharged proteins are usually moved across the single layer by the Sec pathway or the two-arginine (Tat) pathway. Recently efforts focused on transporter and metabolite engineering, visualize the improvement and enhancement of microbial cell to pass such metabolites these metabolite carrier proteins are inserted into the inner membrane of mitochondria across the inner membrane, specialized carrier proteins are necessary that mediate the transport into and out of the mitochondrial matrix. Two main strategies for metabolic engineering in plants: the introduction of genes encoding new enzymes and the use of TFs controlling specialized metabolic pathways

It has remained a hard nut for years to segment sonar images, most of which are noisy images with inevitable blur after noise reduction. For the purpose of solutions to this problem, a fast segmentation algorithm is proposed on the basis of the gray value characteristics of sonar images. This algorithm is endowed with the advantage in no need of segmentation thresholds to be calculated. To realize this goal, it follows the undermentioned steps: first, calculate the gray matrix of the fuzzy image background. After adjusting the gray value, segment the region into the background region, buffer region and target regions. After filtering, reset the pixels with gray value lower than 255 to binarize images and eliminate most artifacts. Finally, remove the remaining noise from images by means of morphological image processing. The simulation results of several sonar images show that the algorithm can segment the fuzzy sonar image quickly and effectively, with no problem of incomplete image target shape. Thus, the stable and feasible method is testified.

Melon (Cucumis melo L.) a member of family Cucurbitaceae is extensively cultivated for its fleshy fruits. Based on the specific agro-climatic zones of cultivation as well as concerning the regional preferences, melon displays significant variability phenotypic and biochemical attributes. Below, an effort is put forth to considerably evaluate the scope of achievements while in the growth as well as the enactment of melon breeding programs by employing the newest solutions. Melon breeding has achieved critical milestones throughout the previous century, and we hope this trend will go on to persist down the road. However, studies have to determine new genetic information for genes associated with the challenges imposed by climate change. The identification of valuable hereditary and also metabolic variability in the form of landraces and melon wild relatives will be useful for harvest diversification and also for the broadening of the cultivated melon genetic base. Whereas, considerable information on genomics, and melon metabolomics, is beneficial for dissecting the basis of the inheritance of important traits and their impact on the former characteristics. Overall, we hope the manuscript is going to serve as a crucial resource for the melon breeders.

Three-dimensional (3D) bioprinting promises to be essential in tissue engineering for solving the rising demand for organs and tissues. Some bioprinters are commercially available, but their impact on the field of TE is still limited due to their cost or difficulty to tune. Herein, we present a low-cost easy-to-build printhead for microextrusion-based bioprinting (MEBB) that can be installed in many desktop 3D printers to transform them into 3D bioprinters. We can extrude bioinks with precise control of print temperature between 2 - 60 ºC. We validated the versatility of the printhead, by assembling it in three low-cost open-source desktop 3D printers. Multiple units of the printhead can also be easily put together in a single printer carriage for building a multi-material 3D bioprinter. Print resolution was evaluated by creating representative calibration models at different temperatures using natural hydrogels such as gelatin and alginate, and synthetic ones like poloxamer. Using one of the three modified low-cost 3D printers, we successfully printed cell-laden lattice constructs with cell viabilities higher than 90% after 24h post printing. Controlling temperature and pressure according to the rheological properties of the bioinks was essential in achieving optimal printability and great cell viability. The cost per unit of our device, which can be used with syringes of different volume, is less expensive than any other commercially available product. These data demonstrate an affordable open-source printhead with the potential to become a reliable alternative to commercial bioprinters for any laboratory.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

In MBSE there is yet no converged terminology. The term ’system model’ is used in different contexts in literature. In this study we elaborated the definitions and usages of the term ’system model’, to find a common definition. 104 publications have been analyzed in depth for their usage and definition as well as their meta-data e.g., the publication year and publication background to find some common patterns. While the term is gaining more interest in recent years it is used in a broad range of contexts for both analytical and synthetic use cases. Based on this three categories of system models have been defined and integrated into a more precise definition.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

Recently there has been growing interest in the application of game theory (GT) to solve many diverse problems in the field of construction, including i.a.: tender preparation, selection of a contractor for construction works, negotiating terms and conditions of cooperation of the parties to the contract, analysis and modeling of investment risk. In the authors opinion, the use of GT by general contractor (GC) of construction works to indicate the best strategy leading to winning court proceedings in a situation of conflict with investor (IN), so far has not been the subject of research. Taking into account the above, the aim of the presented paper is to indicate the optimal strategy from the GC point of view in the conflict situation with IN. The article presents a list of the most common causes of conflicts between parties of the construction works' contract, defines the background of the problem and the cause of the dispute, and on its basis, the authors generate the theoretical model of the game. Based on the analyzed game model, expected payoffs for players were calculated and the probability border value at which GC should apply the indicated strategy determined. The results of the study show that in the case when the probability of issuing a judgment favorable for GC is at least equal to 69.23%, it is justified to use an aggressive strategy. The analysis also confirms that from the financial perspective, litigation in most cases of conflicts in the area of construction should be the last choice.

This article deals with the possibility of partial replacement of blast furnace slag with fly ash after denitrification by the Selective Non-Catalytic Reduction (SNCR) method in alkali-activated materials. In the experiment, the basic physical-mechanical properties and durability properties were tested, the hydration reaction was monitored in a calorimeter and infrared spectroscopy was performed. Results were compared between mixtures prepared with fly ash without denitrification and also with reference mixture based only on alkali-activated blast furnace slag. The basic result is the finding, that hybrid alkali-systems with fly ash after denitrification show similar trends as hybrid alkali-systems with fly ash without denitrification. The significant effect of fly ash is manifested especially in terms of resistance to freeze-thaw. The reactions in the calorimeter show a slower development of reactions with increasing replacement of slag by fly ash. In the case of testing resistance to leaching in demineralised water, a decrease of flexural strength was found, which corresponds to the conclusions of strength testing, that long-term deposition of bodies in water causes deterioration of mechanical properties.

The four-way reversing valve is a key component determining whether a heat pump air conditioning system can work. Studying the four-way reversing valve is of great significance for improving the performance of the heat pump air conditioning system. In this paper, the control equation of the sliding block movement process is constructed to simulate the reversing process of the four-way reversing valve in fluid mechanics, and a detailed study is carried out from the sliding block speed, sliding block acceleration, sliding block force, refrigerant leakage, and other aspects. Research has shown that optimizing the structure of the slider can greatly improve the working performance of the four-way reversing valve. Increasing the height of the slider not only improves the pressure relief ability of the four-way reversing valve and prevents the slider from being damaged by high-pressure gas impact, but also reduces the leakage of refrigerant during the directional process; When reducing the length of the slider, although it will improve the pressure relief capacity of the four-way reversing valve, it also increases the amount of refrigerant leakage. The research results provide a theoretical basis and improvement direction for designers to improve the performance of four-way reversing valves.

In the article, the authors presented the problem of the transition effect in bridge engineering, its causes, negative consequences, and suggested a solution involving the use of integral bridges with the embankment through a spatial bars structure using reinforced composite polymer material. Integral bridges are designed to collaborate with road or railway embankments in bearing loads. Additionally, their application minimizes maintenance and construction costs while enhancing durability. Current solutions in bridge engineering were described. It is predicted that the presented concept will reduce the amount of plastic waste and contribute to the long-term use of materials. The article emphasized the importance of sustainable development, recycling, and the potential application of substitute materials.

This study explored drivers’ emotion-based impressions of car-borne central control platforms (CBCCPs) personal-use vehicles. Thus, this preference-based study examined experts’ and drivers’ opinions regarding CBCCPs’ appeal from the perspective of Miryoku engineering. To this end, this study analyzed data via the EGM (evaluation grid method (EGM) and quantification theory type I. Results: Drivers’ preferences for specific CBCCP design characteristics were categorized into the factors “legible,” convenient,” and “tasteful,” which comprised the core of the EGM semantic hierarchical diagram. In addition, the importance of CBCCPs’ appeal factors and characteristics was assessed through quantification theory type I.The findings of this study provide valuable insights for designers, manufacturers, and researchers interested in the design of CBCCPs. Additionally, the results of this study can contribute to research on applied psychology, human-computer interactions, and car interface design.

Yeasts belonging to the Metschnikowia genus are particularly interesting for the unusual formation of only two needle-shaped ascospores during their mating cycle. Presently, the meiotic process that can lead to only two spores from a diploid zygote is poorly understood. The expression of fluorescent nuclear proteins should allow the meiotic process to be visualized in vivo; however, no large-spored species of Metschnikowia has ever been transformed. Accordingly, we aimed to develop a transformation method for Metschnikowia borealis, a particularly large-spored species of Metschnikowia, with the goal of enabling the genetic manipulations required to study biological processes in detail. Genetic analyses confirmed that M. borealis, and many other Metchnikowiacea, are CUG-Ser yeasts. Codon-optimized selectable markers lacking CUG codons were used to successfully transform M. borealis by electroporation and lithium acetate, and transformants appeared to be the result of random integration. Mating experiments confirmed that transformed-strains were capable of generating large asci and undergoing recombination. Finally, random integration was used to transform an additional 18 yeast strains, and all attempts successfully generated transformants. The results provide a simple method to transform many yeasts from an array of different clades and can be used to study or develop many species for various applications.

Utilizing ecological engineering to manage pests by enhancing the biological control function of natural predators through the selection of high-efficiency bank plants and the establishment of bank plant systems within agricultural ecosystems is an optimal strategy. While bank plant systems have found widespread use in greenhouse crop cultivation, their application in rice fields remains limited. This study aimed to assess the efficacy of Leersia sayanuka as a bank plant for controlling planthoppers and to explore the potential of sesame as a complementary plant to enhance the effectiveness of the bank plant system through field trials. The findings revealed that planting a strip of L. sayanuka, at least 50 cm wide and extending over 1 m in length, had a notable impact on planthopper control in paddy fields. Moreover, the incorporation of Sesamum indicum, a nectar plant, into the bank plant system consisting of L. sayanuka, Nilaparvata muiri, and Anagrus nilaparvatae, led to a significant increase in the population of Anagrus spp. in rice fields. This increase was accompanied by a rise in the egg parasitism rate targeting rice planthoppers, resulting in a marked improvement in overall rice planthopper control in paddy fields. Thus, the combined system demonstrated efficiency as an effective bank plant system for managing rice planthoppers.

Curdlan is a water-insoluble polymer that has structure and gelling properties useful in a wide variety of applications such as in medicine, cosmetics, packaging and the food and building industries. The capacity to produce curdlan has been detected in certain soil-dwelling bacteria of various phyla, although the role of curdlan in their survival remains unclear. One of the major limitations of the extensive use of curdlan in industry is the high cost of production during fermentation, partly because production involves specific nutritional requirements such as nitrogen limitation. Engineering of the industrially relevant curdlan-producing strain Agrobacterium sp. ATTC31749 is a promising approach that could decrease the cost of production. Here, during investigations on curdlan production, I found that curdlan was deposited as a capsule. Curiously, only a part of the bacterial population produced a curdlan capsule. This heterogeneous distribution appeared to be due to the activity of Pcrd, the native promoter responsible for the expression of the crdASC biosynthetic gene cluster. To improve curdlan production, Pcrd was replaced by a promoter (PphaP) from another Alphaproteobacterium, Rhodobacter sphaeroides. Compared to Pcrd, PphaP was stronger and only mildly affected by nitrogen levels. Consequently, PphaP dramatically boosted crdASC gene expression and curdlan production. Importantly, the genetic modification overrode the strict nitrogen depletion regulation that presents a hindrance for maximal curdlan production and from nitrogen rich, complex media, demonstrating excellent commercial potential for achieving high yields using cheap substrates under relaxed fermentation conditions.

Mucosal vaccines offer several advantages over injectable conventional vaccines, such as adaptive immunity induction, secretory IgA production at the entry site of most pathogens, and needleless vaccinations. Despite their potential, only a few mucosal vaccines are currently used. Developing new effective mucosal vaccines strongly relies on identifying innovative anti-gens, efficient adjuvants, and delivery systems. Several approaches based on phages, bacteria, or nanoparticles have been proposed to deliver antigens to mucosal surfaces. Bacterial spores have also been considered antigen vehicles, and various antigens have been successfully exposed on their surface. Due to their peculiar structure, the spores conjugate the advantages of live microorganisms with synthetic nanoparticles. When mucosally administered, spores expressing anti-gens have been shown to induce antigen-specific, protective immune responses. This review accounts for recent progress in the formulation of spore-based mucosal vaccines, describing the spore's structure, specifically the spore surface, and the diverse approaches developed to improve its efficiency as a vehicle for heterologous antigen presentation.

Extracellular vesicles are considered a novel therapeutic tool, due to their ability to transfer their cargoes to target cells. Different strategies to directly load extracellular vesicles with RNA species have been proposed. Electroporation has been used for the loading of non-active vesicles, however the engineering of vesicles already carrying a therapeutically active cargo is still under investigation. We here set up a coincubation method to increase the anti-tumor effect of extracellular vesicles isolated from human liver stem cells (HLSC-EVs). Using the coincubation protocol, vesicles were loaded with the anti-tumor miRNA-145, and their effect was evaluated on renal cancer stem cell invasion. Loaded HLSC-EVs maintained their integrity and miR transfer ability, and miR-145 was protected by RNAse digestion possibly due to its binding to RNA-binding proteins on HLSC-EV surface, such as Annexin A2. Moreover, miR-145 coincubated HLSC-EVs were more effective in inhibiting the invasive properties of cancer stem cells, in comparison to naïve vesicles. The protocol reported here exploits a well-described property of extracellular vesicles to bind nucleic acids on their surface and protect them from degradation, in order to obtain an effective miRNA loading that results in the increase of the effect of naïve active extracellular vesicles.

Land engineering is a specific new academic discipline in China. Although the undergraduate major of land engineering was officially approved and established lately since 2017, the birth of land engineering as an academic discipline dates back 40 years ago. It has passed through four development stages: the incubation stage in 1978-1985, the initial stage in 1986-1997, the growth stage in 1998-2011, and the expanding stage from 2012 to present. However, land engineering as an academic discipline remains immature and seriously lags behind practice. There are still no unified academic community and broad academic consensus. After a historical overview of the four development stages, this study gave a strategic consideration to five key questions. We argue that the study object of the discipline is land engineering activity, which is defined as the artificial transformation of a land complex combined by various natural and human elements. The uniqueness of the discipline is rooted in its ability to study the comprehensive and integrated reorganization or rebuilding of various elements of land as a complex, with the theory of land complex reconstruction being the core theory. The discipline of land engineering is based on land pure science and land technology, and is one basis of land management. It consists of two modules (rural land engineering and urban land engineering), five secondary disciplines of each module (land development, land rearrangement, land improvement, land protection, and land remediation), and more than 30 research directions. Various technologies are only instrumental but not essential components of land engineering as an academic discipline.

To establish simulated micro-gravity conditions, biological organisms are placed on a simulated microgravity system, which primarily rotate in two or three dimensions and rely on slow sedimentation with latency to detect gravity. Fluid dynamics arise as a consequence of rotation of the chambers with in which the cells are filled. To minimize the effects of centrifugal forces, it is necessary to position the samples as close to the center of rotation as possible. Strong shear forces and velocities within the vessel can have an adverse impact on cells, making this a critical topic in cell biology. During experimental investigation, this specific phenomenon is not apparent, but numerical modelling readily illustrates and is not widely analyzed in literature's. Furthermore, bulk flask are frequently employed on random positioning machines (RPM), not merely because they demand a substantial quantity of reagents. The flask presented in the study can be easily developed and fitted in conventional cell culture plates containing medium and reagents similar to those used in ground experiments, thus allowing it to remain close to the center of rotation. In the present study, a series of fluid dynamics simulations are performed to examine the impact of shear forces within the microvessel presented under varying conditions using a foreign medium condition, and these results are compared with existing vessels by observing the effects of shear forces and maximum velocity zones.

COVID-19, caused by SARS-CoV-2, is responsible for widespread mortality and economic loss across almost 212 countries. The distribution of disease prevalence is, however, uneven and likely dependent on the range of human behavior and/or the pathogen and environmental variables. Here in this research we examined the correlation between daily and total COVID-19 case reports from Bangladesh and meteorological variables (average temperature, average humidity, and average wind speed) against one another using Spearman rank and Kendall correlation tests to highlight significant meteorological variables in relation to COVID-19. The tests revealed that both temperature and humidity had a non-significant correlation with COVID-19 transmission amid epicenter (EC) and non-epicenter (NEC) areas. However, a weak (KCC: 0.168, p < 0.05; SCC: 0.271, p < 0.05) correlation was found for temperature in ECs. Wind speed showed moderate to strong correlation in ECs with a very high statistical significance to both daily new cases [(KCC: 0.494, p < 0.01); (SCC: 0.689, p < 0.01)] and total cases [(KCC: 0.426, p < 0.01); (SCC: 0.617, p < 0.01)]. The COVID-19 transmission was found to have a weak (KCC: 0.354, p < 0.01) to moderate (SCC: 0.465, p < 0.01) correlation with daily new cases; however, a moderate (KCC: 0.497, p < 0.01) to strong (SCC: 0.712, p < 0.01) correlation with total cases was found in NECs. The results suggest that temperature and humidity have little influence on COVID-19 transmission, but wind speed may have some influence. Countries should prioritize social engineering to modify human behavior in order to combat the spread of COVID-19 and future pandemics.

Nano-scale organofunctional silanes have been developed, tested and successfully applied to protect stone buildings in Europe against climatic effects since the 1860s. The same nanotechnologies can also be used in pavement engineering to create strong chemical bonds between a stabilising agent and the material substrata. The attachment of the organofunctional silane to a material also makes the surface of the material hydrophobic, reducing future chemical weathering. These properties allow naturally available materials to be used in any pavement layer at a low risk. In the built environment, scientists soon determined that the successful use of an organo-silane depends on the type and condition of the stone to be treated. The same principles apply to the implementation of applicable nanotechnologies in pavement engineering. Understanding the basic chemistry determining the properties of the stabilising agent and the organofunctional modifying agent and the chemical interaction with the primary and secondary minerals of the material are essential for the successful application of these technologies in pavement engineering. This paper explains some basic chemistry which fundamentally influences engineering outputs that can be achieved using New-age (Nano) Modified Emulsions (NME) stabilising agents with naturally available material in all road pavement TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

The key to building a strong bridge country lies in talent, and the foundation lies in education. The cultivation of bridge engineering talents is related to the future and destiny of building a strong bridge country. This course adopts the educational philosophy of "holographic teaching method" centered on the comprehensive development of students, cultivating "engineering thinking" guided by engineering education certification, enhancing "abilities and qualities" through professional knowledge, reconstructing the course knowledge content system through engineering philosophy thinking, and implementing the ideological and political construction of the course in a multi-level unified manner of "explicit + implicit". Based on restructuring the course content system, we will strengthen the construction of diversified course resources, integrate theory with practice throughout the entire process of the course, practice the concept of "bridge architects + bridge engineers" parallel development, and cultivate cross-border and compound talents with comprehensive qualities of "engineering + art + humanities".

Amino acid efflux and influx transport systems play vital roles in industrial microorganisms’ cell growth and metabolism. However, although biochemically characterized, most amino acid transporters remain unknown at the molecular level in Bacillus licheniformis. This study focuses on the molecular and functional characterizations of three transporters, YdgF, YvbW, and YveA, mainly when catalyzing the cross-membrane flux of L-Aspartate. When growing in the minimal medium with L-Asp as the only carbon and nitrogen source, the growth of strains lacking proteins YdgF, YvbW, and YveA was significantly inhibited compared with wild-type strains, while supplementing the expression of the corresponding proteins in the single-gene knockout strains can alleviate the inhibition to some extent. Upon overexpression, the recombinant proteins mediate the accumulation of L-aspartate to varying degrees. Compared with wild-type strains, the single knockout strains of the three protein genes exhibited reduced absorption of L-aspartate. In addition, this paper focuses on the effects of these three proteins on the absorption of β-alanine, L-glutamate, D-serine, D-alanine, and glycine.

We have performed the first comparative analysis of the potential of two physiologically-diverse model cyanobacteria, Synechococcus PCC 7002 (S.7002) and Synechococcus PCC 7942 (S.7942), for the photosynthetic production of four chemically-different high-value terpenes: two monoterpenes limonene and pinene, and two sesquiterpenes bisabolene and farnesene. We showed, for the first time, that S.7002 and S.7942 can produce farnesene and bisabolene, respectively. Both cyanobac-teria produced farnesene (S.7942 better than S.7002) more efficiently than the other tested terpenes (especially pinene the weakest produced terpene). S.7002 produced limonene better than bisabo-lene, whereas S.7942 produced bisabolene better than limonene. These findings suggest that S.7942 is better suited to produce sesquiterpenes than monoterpenes. Also interestingly, higher levels of terpenes were produced by S.7942 and S.7002 expressing a terpene-synthase gene from both a RSF1010-derived replicating plasmid and a neutral chromosomal site, as compared to ei-ther the plasmid alone or the chromosome alone. These results suggest that in both cyanobacteria the production of terpenes is more limited by the activity of terpene synthases than the abondance of terpene precursors. Finally, higher levels of terpenes were produced by S.7002 growing on urea (a frequent pollutant) as compared to nitrate (or ammonium) the standard nitrogen sources for cyanobacteria (more expensive than urea).

The study of ecosystems, both natural and artificial, has historically been mediated by population dynamics theories. In this framework, quantifying population numbers and related variables (associated with metabolism or biological-environmental interactions) plays a central role in measuring and predicting system-level properties. As we move towards advanced technological engineering of cells and organisms, the possibility of bioengineering ecosystems (from the gut microbiome to wildlands) opens several questions that will require quantitative models to find answers. Here, we present a comprehensive survey of quantitative modelling approaches for managing three kinds of synthetic ecosystems, sharing the presence of engineered strains. These include test tube examples of ecosystems hosting a relatively low number of interacting species, mesoscale closed ecosystems (or ecospheres), and macro-scale, engineered ecosystems. The potential outcomes of synthetic ecosystem designs and their limits will be relevant to different disciplines, including biomedical engineering, astrobiology, space exploration and fighting climate change impacts on endangered ecosystems. We propose a space of possible ecosystems that captures this broad range of scenarios and a tentative road map for open problems and further exploration.

Cartilage degeneration is a characteristic of osteoarthritis (OA) which is often observed in aging populations. This degeneration is due to the breakdown of articular cartilage (AC) mechanical and tribological properties, primarily attributed to lubrication failure. Understanding the reasons behind these failures and identifying potential solutions could have significant economic and societal implications, ultimately enhancing the quality of life. This review provides an overview of developments in the field of AC, focusing on its mechanical and tribological properties. The emphasis is on the role of lubrication in degraded AC, offering insights into its structure and function relationship. Further it explores the fundamental connection between AC mechano-tribological properties and the advancement of its degradation and puts forth recommendations for strategies to boost its lubrication efficiency.

Gene editing is now easy to make new disease models through in-vivo and in vitro tests. It can potentially be used to make animals with single-gene or multiple-gene changes. The mutant strains with changed germlines are no longer needed with in vivo gene editing, which uses the CRISPR-Cas9 system to target cells of interest in their normal tissues. Whereas, the AAVs and other viral vectors have made it possible to change cells selectively. Gene editing hade made it possible to use human induced pluripotent stem cells (iPSC) to model diseases that run in families. Researchers can compare and contrast the human genomes of many different ethnic and racial groups using this method. Scientists may be able to make a disease in a lab dish using iPSCs from a patient. Using CRISPR, iPSCs made from patient cells can be fixed if they have certain problems. This shows that gene therapy is possible and shows what happens when cells aren't working right. The fact that CRISPR-Cas9 can change the DNA by just one nucleotide has had a huge effect on biological studies. CRISPR is becoming more and more popular, which shows how useful, easy, and effective it is. With the broad use of CRISPR-based apps, the tool is now used for much more than just changing genes. This method can be used to screen the whole genome, control the translation of genes based on their sequence, and edit several genes at the same time. Scientists can now model diseases in different species and learn more about how genes work because of these advances. Genome-wide association studies and genome-editing tools like CRISPR are giving us a good look at the future of personalized medicine.

The catalytic parameters describing enzyme catalysis are discussed in the context of the design of de novo enzymes. It is shown that high values of the catalytic efficiency may in some cases reflect tight substrate binding and lead to an immediate levelling-off of rates to reach a low plateau, an undesirable scenario for many industrial applications. It is argued that increasing the catalytic rate constant should be a main target in de novo enzyme engineering.

Passive marine listening, involving the acoustic monitoring of underwater environments, has become increasingly vital for scientific research, environmental monitoring, and defense applications. However, the success of such applications critically depends on the ability to extract meaningful information from the often noisy and dynamic underwater acoustic environment. In this context, Mel-frequency cepstral coefficients (MFCCs) have emerged as an essential tool for feature extraction, capturing the spectral characteristics of marine sounds and making them ideal for species identification and sound event detection. This research presents an innovative approach to enhance the robustness of MFCC-based passive marine listening through adaptive noise reduction techniques. The proposed approach utilizes dynamic spectral subtraction to counter underwater noise, resulting in enhanced signal-to-noise ratios for desired sounds. This adaptive system adjusts to dynamic underwater noise, allowing it to concentrate on target sounds and suppress interference effectively. The experimentation further validates the effectiveness of the proposed approach, with results reaching 99% on the full dataset of 570 mammals and vessels, demonstrating the effectiveness of SVM and Random Forests in the classification of underwater audio.

Microbial cell factories offer an eco-friendly alternative for transforming raw materials into commercially valuable products, primarily because of their reduced carbon impact compared to conventional industrial procedures. These systems often depend on lignocellulosic materials, mainly pentose and hexose sugars, richly available carbon reservoirs. Nevertheless, these resources might not always be efficient due to the limited supply, significant cost, and other considerable obstacles. One major hurdle when working with sugars derived from lignocellulosic biomass, especially glucose, is balancing carbon allocation to satisfy energy, cofactor, and other essential component needs for cellular proliferation while maintaining a robust yield. Furthermore, nearly half or more of this carbon is inevitably lost as CO2 during the biosynthesis processes, which serves to generate the energy necessary for maintaining cell growth and other regular metabolic activities. This carbon loss lowers the theoretical production yield and compromises the benefit of reducing greenhouse gas emissions – a fundamental advantage of biomanufacturing. This review paper posits the perspectives of using CO2 from atmosphere, industrial wastes, or the exhausted gases generated in microbial fermentation as a feedstock for biomanufacturing. Both one-step direct CO2 fixation or two-step indirect CO2 fixation and conversion strategies are discussed, which can minimize the carbon loss, significantly increase the carbon yield, and eventually achieve the carbon-neutral or -negative goals. The one-step strategy uses novel metabolic pathway design and engineering approaches to directly fix the CO2 via the pathway toward the synthesis of the desired fermentation products. Due to the limitation of the yield and efficiency in one-step CO2 fixation, the two-step strategy aims to completely avoid carbon loss in biomanufacturing by integrating a first electrochemical fixation of the exhausted CO2 into C1/C2 products such as formate, methanol, acetate, and ethanol and a second fermentation unit to utilize the CO2-derived C1/C2 chemicals or co-utilize both C5/C6 sugars and C1/C2 chemicals for product formation. The great potentials and challenges of using CO2 as a feedstock for further biomanufacturing are also discussed.

Silk fibroin (SF) extracted from Bombyx mori cocoons is a biocompatible and biodegradable polymer shows potential as matrices for tissue engineering and regenerative medicine, or con-trolled drug delivery systems. Regenerated fibroin, obtained by removing sericin from natural silk, is water-soluble. Its aqueous solutions can be processed into a variety of materials, for example, fibrous matrices, using the electrospinning method. In this article, the concentration dependences of the properties of aqueous solutions of regener-ated fibroin, that determine the possibility of obtaining electrospun mats for tissue-engineering applications, are studied. A slowdown in the growth of viscosity after a concentration of fibroin of 30% and a decrease in the transparency of the solution were found; this may be due to the on-set of conformational rearrangements: the transition of fibroin from the random coils, charac-teristic for dilute solutions, to the anisotropic conformation of the helix and the appearance of β-pleated sheets. Fibrous mats from regenerated fibroin were obtained from solutions with a concentration of 10 and 20%. Two methods were used to prevent solubility of fibroin-based matrices: conversion of fibroin to the β-conformation by treatment with an ethanol solution and chemical cross-linking with gen-ipin (Gp). The structures of the fibrous samples were studied by AFM and confocal laser scan-ning microscopy. The composition of the moulding solution for the electrospinning of regener-ated fibroin fibrous matrices and the conditions for their modification have been optimised. It has been shown that the composition of fibroin with chitosan contributes to a decrease in the solubility of electrospun fibrous matrices by increasing the number of amino groups available for modification by Gp, and also leads to a decrease in the diameter of the fibers. Electrospun fiber matrices based on regenerated SF, modified by cross-linking with Gp in water-alcohol solutions, promote cell growth and proliferation and may be promising for tissue engineering.

Regenerative endodontic procedures (REPs) aim at recreating dental pulp tissue using biomaterials such as hydrogels. Their bioactivity is mostly linked to the nature of biomolecules or chemical compounds that will compose the endodontic hydrogel. However, many other parameters, such as hydrogel concentration, type, bioactive molecules solubility, of apex size were reported to influence the hydrogel behavior, leading to the inability to predict the clinical outcome. This lack of knowledge and the various parameters that should be considered, suggest that biological activity of endodontic hydrogel is impossible to anticipate and could hinder the bench to bedside transition. We formulated in this article our opinion that most of these parameters could be identified, described, and studied. A second part of the document lists some challenges and perspectives, including development of future mathematical models able to explain and predict the bioactivity of these endodontic hydrogel in clinic.

The advancements achieved in Tissue Engineering are based on a careful and in-depth study of cell-tissue interaction. The choice of a certain biomaterial in Tissue Engineering is fundamental as it represents an interface for adherent cells in the creation of a microenvironment suitable for cell growth and differentiation. The knowledge of the biochemical and biophysical properties of the extracellular matrix is a useful tool for the optimization of polymeric scaffolds. The aim of this re-view is to analyse the chemical, physical and biological parameters on which it is possible to act in Tissue Engineering for the optimization of polymeric scaffolds. Understanding the scaffold impact on cell fate is of paramount importance for the successful advancement of Tissue Engineering.

Amidst the strong demand for wood-based products, and the clamor of environmental consciousness, more functional and green solutions arise to meet both of these goals. Pursuant to this, the study looked into the potential of a bio-waste taken from Cocos nucifera tree known as phellem—the tree’s outermost skin made of dead tissues, to be a main component of a new construction material. This study builds on existing research showing phellem is impermeable, buoyant, elastic, has a slow burn rate, and repels water during precipitation, which supports the hypothesis that phellem may be a potential substitute material for dry wall boards. To test this, three (3) formulations were developed as experimental setups to test the physico-mechanical properties of coconut palm phellem (COPAP): Formulation A (40% COPAP and 60% cement); Formulation B ( 25% COPAP and 75% cement); and lastly, Formulation C that was (10% COPAP and 90% cement). The study tested (1) which among these formulations exhibited the best physico-mechanical properties, then it (2) compared the formulations with common dry wall products available in the market, and subsequently, (3) identified the possible architectural applications of COPAP board as a new building material. Of the three setups, Formulation C exhibited the best physico-mechanical properties in terms of compressive and flexural strength, fire resistivity, and water absorption. It fared better than the particle board in terms of compressive strength, better than wafer and particle board in fire resistivity, performed best in the water absorption test, and was almost equivalent in flexural strength to fiber cement board. With these findings, the study concluded that COPAP board can be used for projects that entail a high number of interior partitions, such as offices, BPO firms and commercial stalls in shopping malls, etc. The findings were conclusive only for interior applications, as the results clearly suggest that the COPAP boards are not load-bearing. Future investigations may explore and assess other properties of COPAP boards like thermal and sound insulation, resistance to rot and other properties that may prove its competitive advantage as a construction material.

The results of applying drilling engineering tools in planned deviated and horizontal wells of oil and gas condensate fields have been examined. The basis for the implementation of a comprehensive approach was the information obtained from drilling horizontal wells in the West and East Siberia, Volga-Ural region, and Iraqi Kurdistan. A synthetic model is considered as an example of the data, incorporating geomechanical and geological properties. As a result of the conducted audit of the geomechanical model and drilling process, the methodologies used were further developed to obtain optimal drilling fluid densities, aiming to prevent cavity formation on well walls, hydraulic fractures, and other related issues. The implementation of the Python programming language was introduced in the stages of geomechanical model preparation, resulting in a time acceleration of up to 20%. During the pre-drilling stage, technological operations were synchronized with the geomechanical model, increasing the involvement of process participants through the synchronization of knowledge areas. The interrelation between drilling technology, drilling parameters, properties of flushing fluids, and rock stability analysis was established, ensuring a 5% increase in construction speed (through NPT reduction and modification of existing tools and technological operations) and accident-free drilling of complex deviated and horizontal wells, provided that the recommended drilling parameters are followed.

Most neuromorphic technologies use a point-neuron model, missing the spatiotemporal nature of neuronal computation performed in dendrites. Dendritic morphology and synaptic organization are structurally tailored for spatiotemporal information processing, enabling various computations like visual perception. Here, we report on a neuromorphic computational model termed ‘dendristor’, which integrates functional synaptic organization with dendritic tree-like morphology computation. The dendristor presents bioplausible nonlinear integration of excitatory and inhibitory synaptic inputs with silent synapses and diverse spatial distribution dependency. We show that the dendristor can emulate direction selectivity, which is the feature to react robustly to a preferred signal direction on the dendrite. We discover that silent synapses can remarkably enhance direction selectivity, turning out to be a crucial player in dendritic computation processing. Finally, we develop neuromorphic dendritic neural circuits that can emulate a cognitive function such as motion perception in the retina. Using dendritic morphology, we achieve visual perception of motion in 3D space by various mapping of spatial information on different dendritic branches. This neuromorphic dendritic computation innovates beyond current neuromorphic computation and provides solutions to explore new skylines in artificial intelligence, neurocomputation, and brain-inspired computing.

2,7-bis(pyridin-4-ylethynyl)-9H-carbazole (1) was synthesized by reacting 4-ethynylpyridine hydrochloride with 2,7-dibromo-9H-carbazole. The full characterization of compound 1 is presented, and the crystal structure of its monohydrate co-crystal was determined by single-crystal XRD analysis.

In Model-Driven Development (MDD), the models, their generation, and imposing changes on them (model transformation) are used for the development of software. Models provide a framework to start from the imagination and abstraction to create and accomplish the final system. Models create a slow and steady transition from whatness to howness, i.e. from the natural path of the generation of software. For supporting this path, the Logic and Functionality of software must be changeable during its evolution. Here we provide a brief introduction to the concept of Model Driven Development.

Currently, the clinical impact of cell therapy after a myocardial infarction (MI) is limited by low cell engraftment due to significant cell death, including apoptosis, in an infarcted, inflammatory, poor angiogenic environment, low cell retention and secondary migration. Cells interact with their environment through integrin mechanoreceptors that control their survival/apoptosis/differentiation/migration/proliferation. Optimizing these interactions may be a way of improving outcomes. The association of free cells with a 3D-scaffold may be a way to target their integrins. Collagen is the most abundant structural component of the extracellular matrix (ECM) and the best contractility levels are achieved with cellular preparations containing collagen, fibrin, or Matrigel (i.e. tumor extract). In the interactions between cells and ECM, 3 main proteins are recognised: collagen, laminin and RGD (Arg-Gly-Asp) peptide. The RGD plays a key role in heart development, after MI, and on cardiac cells. Cardiomyocytes secrete their own laminin on collagen. The collagen has a non-functional cryptic RGD and is thus suboptimal for interactions with associated cells. The use of a collagen functionalized with RGD may help to improve collagen biofunctionality. It may help in the delivery of paracrine cells, whether or not they are contractile, and in assisting tissue engineering a safe contractile tissue.

Technological innovation has led to the development of increasingly efficient and complex industrial plants. To manage this complexity, it is necessary to define an integrated vision of the socio-technological system that includes: technological, human and organizational component. Petrochemicals can be considered one of the most complex socio-technical systems that deserve special attention to high risk management, especially during the emergency conditions. Traditional safety management models only consider static systems, while new resilience engineering models evaluate the performance variability developed between different actions. One of the recent development methods is the Functional Resonance Analysis Method (FRAM) that identifies the pairs between the functions. FRAM unfortunately is a qualitative model, this research integrates this model with the Performance Shaping Factors (PSFs) and with the Bayesian approach to identify the performance variability of the system. The analysis aims to develop a system that improves safety analysis. The proposed model is applied in a case study of an emergency in a petrochemical company.

Background Tropical and subtropical crops such as coffee, cacao, and papaya are valuable commodities and its consumption is a seemingly indispensable part of the daily lives of billions of people across the world. Conventional breeding in these crops is lengthy and yields are threatened by runaway global warming. In this review we propose the application of chromosome engineering and synthetic biology principles in order to enhance synthesis of key metabolites, and transmission of wild traits for resistance to stress and disease. Conclusions It is hoped that the adoption of such technological approaches may enhance the resilience of agricultural communities, lead to economic growth and secure the availability of key resources for generations to come.

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

With the continuous improvement of people's quality of life and aesthetics, furniture products have higher requirements. Excellent solid wood chairs are the most representative products in furniture to enhance space and taste and whose design may significantly impact consumers' emo-tional experience and purchase decisions. This study aims to evaluate how the modeling imagery of solid wood chairs affects user preferences and emotional experiences. The development of the current era is inseparable from the analysis of big data. Firstly, a representative sample was ob-tained by multidimensional scaling (MDS), and the sample was analyzed and evaluated by fac-tor analysis. Moreover, five groups of adjective vocabulary were selected to describe the model-ing imagery of solid wood chairs, such as "balanced and coordinated", "unique and novel", "prac-tical and simple", "quality and detailed" and "traditional and plain". Further, the triangular fuzzy theory was applied to analyze and discuss the 12 types of solid wood chairs in the five groups of adjective vocabulary. Then the study verified that the differences in the evaluations of the 12 sam-ples in the "unique and novel" and "quality and detailed" groups were significant, but more minor differences in the groups of "traditional and plain", "balanced and coordinated" and "practical and simple". Through comprehensive comparison, five groups with similar modeling imagery were created, and solid wood chairs with different modeling imagery should be placed in suita-ble spaces. According to the results of this study, the evaluation of the modeling imagery of solid wood chairs can not only rely on subjective judgments but can be reasonably described through data analysis and mathematical algorithms. It can scientifically and effectively reflect the poten-tial perception needs of consumers on the modeling imagery of solid wood chairs, as well as help to improve the design efficiency of the furniture product development stage.

One of the main technological and economic challenges for an engineer is designing high-quality products in manufacturing processes. Most of these processes involve a large number of variables included the setting of controllable (design) and uncontrollable (noise) variables. Robust Design (RD) method uses a collection of mathematical and statistical tools to study a large number of variables in the process with a minimum value of computational cost. Robust design method tries to make high-quality products according to customers’ viewpoints with an acceptable profit margin. This paper aims to provide a brief up-to-date review of the latest development of RD method particularly applied in manufacturing systems. The basic concepts of the quality loss function, orthogonal array, and crossed array design are explained. According to robust design approach, two classifications are presented, first for different types of factors, and second for different types of data. This classification plays an important role in determining the number of necessity replications for experiments and choose the best method for analyzing data. In addition, the combination of RD method with some other optimization methods applied in designing and optimizing of processes are discussed.

With the continuous emergence and application of new technologies, the construction of smart cities has entered the practical promotion period. Since 2012, the pilot construction of smart city has been promoted by the government in China. On the basis of these practical experiences, this paper presents an overview of the latest technologies and applications for smart city construction in China and demonstrates that smart city strategy needs to be implemented according to local conditions, adhering to the people-oriented concept and using scientific and effective top-level design and planning. The construction of smart city is comprehensive system engineering, including the integration of geographic information sharing service platform, full-cycle management and control system of urban planning, construction and social management, as well as intelligent business information management system of gardening, water conservancy, environmental protection and other industries and departments. The information system (GIS), satellite remote sensing (SRS), global navigation satellite system (GNSS), Internet of things, mobile applications, cloud computing, visualization technology ware used to promote urban construction and sustainable development, and to meet the needs of future smart city development. Results show that centralized management is very important for the construction of smart city. The government plays a major role in the construction of smart city, which will be conducive to the development of new technologies and the effective use of smart city construction resources.

Background: Multifunctional nanoparticles are known for their wide range of biomedical applications. Controlling the magnetic properties of these nanoparticles is imperative for various applications, including therapeutic angiogenesis. The study was performed to evaluate the magnetic properties and their control mechanisms by the external magnetic field. Methods: A 100nm magnetic nanoparticle was placed in the magnetic field, and parametrically the magnet field strength and distance was evaluated. Various models of magnetic strength and disposition were evaluated. Magnetic flux density, force/weight, and magnetic gradient strength were the parameters evaluated in electromagnetic computational software. Results: The seven-coil method with three centrally placed coils as Halbach array, and each coil with a flux density of 7 Tesla, and with a coil dimension of 20cmx20cm (square model) of each coil showed a good magnetic strength and force/weight parameters in a distance of 15cm from the centrally placed coil. The particles were then evaluated for their motion characteristics in saline. It showed good displacement and acceleration properties. After that, the particles were theoretically assessed in a similar mathematical model after parametrically correcting the drag force. After application of high drag forces, the particles showed adequate motion characteristics. When the particle size was reduced further, the motion characteristics were preserved even with high drag forces. Conclusion: There is potential for a novel method of controlling multifunctional magnetic nanoparticles using high magnetic fields. Further studies are required to evaluate the motion characteristics of these particles in-vivo and invitro.

To facilitate the promotion and application of the whole process engineering consulting (WPEC) model, the transmission mechanism of influencing factors in WPEC's promotion and application is investigated. It identifies and categorizes the influencing factors within the framework of "external environment-project factors-stakeholders", systematically organizing and summarizing ten primary categories and thirty-eight secondary influencing factors of WPEC's promotion and ap-plication. Utilizing the complex network analysis method, a network of influencing factors in the promotion and application of WPEC is constructed. The network is then converted into three binary networks based on weight, which are subjected to structural analysis and motif analysis. On this basis, the transmission mechanism of influencing factors in WPEC's promotion and applica-tion and its causations are explored.

For the emerging autonomous swarm technology, from the perspective of systems science and systems engineering, there must be some novel elements and methods to aggregate multiple systems into a group, which distinguish with the general components with specific functions, and we expect to provide the presentation of their existence in the swarm development processes. The inspiration of our methodology origins from the integration of swarm ontology, multi-paradigm modeling, multi-agent system, cyber-physical system, etc. Therefore, we choose the model-driven technology as a framework to acquire an approach of model representation across the multiple levels of abstraction and composition. The autonomous strategic mechanism is defined and formed in parallel with ConOps analysis and systems design, so as to effectively solve the cognitive problem of emergence caused by the nonlinear causation among individual and whole behaviors. This approach highlights to use the MBSE processes and their artifacts to embed the meso mechanism to integrate the operational and the functional, and which means to connect the macro and micro aspects in formalism and so to become a whole with its expected goals, and then to verify and validate within a L-V-C simulation environment.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

This paper reviews the pioneering work related to the generation of a sequence of prompts in Pretrained Language Models (PLMs) to automatically complete a complex writing task. The paper identifies the main categories of automated multi-step prompting and discusses their advantages and disadvantages. The paper also proposes an additional approach for automated multi-step prompting with iterative four main phases: in the first phase a sequence of prompts is geared to elicit the structure of the requested task. This is done by identifying the task’s main parts, the general contents of the different parts and their precedence relations. The structure of each main part is iteratively explored to find secondary and tertiary parts if they exist. A second phase is followed by a sequence of prompts that fill in the primary, secondary, and tertiary parts, and seek to fine-tune the result. The third phase reviews the generated text and criticizes it. Based on this criticism a revision is prepared. The fourth phase is fine-tuning the document, with emphasis on section length and text tone. Future research could deal with the system identification of points where the system should initiate interaction with the user for desired feedback and guidance.

Freeze-drying is a well-established process in biomedical engineering for the fabrication of three-dimensional open-porous medical devices, especially those based on biopolymers. One of the most used biopolymers in this field is collagen, the most abundant protein in the human body and the main component of the extracellular-matrix, as well as its derivatives. Freeze-dried collagen-based sponges with a wide variety of attributes can be produced by design and have led to a wide range of successful commercial medical devices, foremost for dental, orthopedic, hemostatic and neuronal applications. However, this is still considered a high-cost and time-consuming process that is often used in a non-optimized manner. By combining advances in other technological fields, the opportunity arises to further evolve this process in a sustainable manner, and optimize the resulting products as well as create new opportunities in this field.

All departments in a business work separately, but for the same purpose.In this article, a system that allows not only the mechanical design department but also the manufacturing, storage, process planning, quality control, electrical design, purchasing departments, etc. to have access to the required information has been developed. Initially, current manufacturng result informations is collected from the project attandees. Secondly, a workflow is designed dependent on the current data flow. All the project stakeholders are introduced to join and use product data management system. In the absence of this kind of system, loss of time, scraps and loss of engineering time would be investigated. This allowed the company owners to be sure that no faulty revision of design will be produced after the system started. On the other hand automation of bill of materials generation provided the purchasing department correct and up to date information about outsourced parts. Allowing different engineering disciplines to work together provided more suitable environment. Gradually this conditions allowed all the departments work faster and market the new product much faster than before the system. Tracing the workflows for management purposes would be handled by the system. A ‘Validation of Design’ process is modelled for the company.

Heavy metal contamination of drinking water is a public health concern that requires the development of more efficient bioremediation techniques. Absorption technologies, including biosorption, provide opportunities for improvements to increase the diversity of metal ions removed and overall binding capacity. Microorganisms are a key component in wastewater treatment plants and they naturally bind metal ions through surface macromolecules but with limited capacity. The long-term goal of this work is to engineer capsule polymerases to synthesize molecules with novel functionalities. In previously published work, we showed that the Neisseria meningitidis serogroup W (NmW) galactose-sialic acid (Gal—NeuNAc) heteropolysaccharide binds lead effectively, thereby demonstrating the potential for using this capsular polysaccharide in environmental decontamination applications. In this study, computational analysis of the NmW capsule polymerase galactosyltransferase (GT) domain was used to gain insight into how the enzyme could be modified to enable the synthesis N-acetylgalactosamine-sialic acid (GalNAc—NeuNAc) heteropolysaccharide. Various computational approaches, including molecular modeling with I-TASSER and molecular dynamics simulations (MD) with NAMD, were utilized to identify key amino acid residues in the substrate binding pocket of the GT domain that may be key to conferring UDP-GalNAc specificity. Through these combined strategies and using BshA, a UDP-GlcNAc transferase, as a structural template, several NmW active site residues were identified as mutational targets to accommodate the proposed N-acetyl group in UDP-GalNAc. Thus, a rational approach for potentially conferring new properties to bacterial capsular polysaccharides is demonstrated.

Fusion protein therapeutics engineering is advancing to meet the need for novel medicine. Herein, we further characterize the development of novel RTA & PAP-S1 antiviral fusion proteins. In brief, RTA/PAP-S1 and PAP-S1/RTA fusion proteins were produced in both cell free and E. coli in vivo expression systems, purified by His-tag affinity chromatography, and protein synthesis inhibitory activity assayed by comparison to the production of a control protein, CalmL3. Results showed that the RTA/PAP-S1 fusion protein is amenable to standardized production and purification and has both increased potency and less toxicity compared to either RTA or PAP-S1 alone. Thus, this research highlights the developmental potential of novel fusion proteins with reduced cytotoxic risk and increased potency.

In recent years, bone tissue engineering (BTE) has made significant progress in promoting the direct and functional connection between bone and graft, including osseointegration and osteoconduction, to facilitate the healing of damaged bone tissues. Herein, we introduce a new, environmentally friendly, and cost-effective method for synthesizing reduced graphene oxide (rGO) and hydroxyapatite (HAp). The method uses epigallocatechin-3-O-gallate (EGCG) as a reducing agent to synthesize rGO (E-rGO), and HAp powder is obtained from Atlantic bluefin tuna (Thunnus thynnus). The physicochemical analysis indicated that the E-rGO/HAp composites had exceptional properties for use as BTE scaffolds, as well as high purity. Moreover, we discovered that E-rGO/HAp composites facilitated not only proliferation, but also early and late osteogenic differentiation of human mesenchymal stem cells (hMSCs). Our work suggests that E-rGO/HAp composites may play a significant role in promoting the spontaneous osteogenic differentiation of hMSCs, and we envision that the E-rGO/HAp composites could serve as promising candidates for BTE scaffolds, stem cell differentiation stimulators, and implantable device components due to their biocompatible and bioactive properties. Overall, we suggest a new approach for developing cost-effective and environmentally friendly E-rGO/HAp composite materials for BTE application.

Due to the fact that to date, the question of the origin of SARS-CoV-2 has not been resolved yet, the author analyzed the main advances in the development of genetic engineering of viruses that took place before the onset of the COVID-19 pandemic. The first artificial genetically modified viruses could appear in nature in the mid-1950s. The technique of nucleic acid hybridization was developed by the end-1960s. In the late 1970s, a method called the "reverse genetics" emerged to synthesize RNA and DNA molecules. In the early 1980-s, it became possible to combine the genes of different viruses and insert the genes of one virus into the genome of another virus. Since that time, the production of vector vaccines began. Currently, by modern technologies one can assemble any virus based on the nucleotide sequence available in the virus database or designed by a computer as a virtual model.Scientists around the world are invited to answer the call of Neil Harrison and Jeffrey Sachs of Columbia University, for a thorough and independent investigation into the origin of SARS-CoV-2. Only a full understanding of the origin of the new virus can minimize the likelihood of a similar pandemic in the future.

Introduction Despite efforts to use scaffolds to treat meniscus tears, minimal progress has been made in facilitating meniscus regeneration and return of function. Our research objective was to develop a meniscus repair and regeneration implant by applying a resorbable scaffold in combination with cells and growth factors. We report here the results of using platelet-rich plasma (PRP) as a source of growth factors to induce fibrochondrogenic differentiation of human adipose-derived mesenchymal stem cells (hADSC) in a three-dimensional (3D) Type I collagen-based scaffold in vitro. Methods Scaffold Preparation. Type I collagen scaffolds were prepared following a protocol previously published. Two different densities of scaffolds, high density (HD) and low density (LD), were produced for in vitro study. hADSC and PRP Preparation. hADSCs were cultured to the fifth passage to reach the desired number for experimentation. PRP was collected from human blood and activated. Cell Culture Procedure. Effects of PRP on hADSC proliferation and differentiation into fibrochondrogenic cells were examined in four scaffold groups: LD, HD, LD+PRP and HD+PRP. hADSCs were seeded onto scaffolds (n=5) at a concentration of 2 × 106 cells/scaffold. 1% of PRP was added to the experimental media. Cellular proliferation was assessed at 1, 7, 14, and 21 days. Differentiation was measured using qRT-PCR on Days 14 and 21. qRT-PCR analysis of gene expression was completed with primers for COLLAGEN 1 and AGGRECAN. Data Analysis. ANOVAs were conducted (two-tailed tests) at the .05 significance level. Results Cellular proliferation of hADSCs seeded on each scaffold increased over time. Similar trend was observed for cells seeded on HD scaffolds with and without PRP. hADSC showed significant increase in cellular proliferation on the LD scaffolds at Days 1 and 7. At Day 21, PRP treatment and LD scaffold had a synergistic positive effect on Type I collagen gene expression. PRP did not elevate type I collagen gene in the HD group, the HD scaffold alone had the same level of type I collagen gene expression as LD+PRP. Aggrecan expression was elevated in the presence of PRP in both the HD and LD scaffold groups, indicating enhanced fibrochondrogenic differentiation of hADSCs. Effective cell infiltration was observed across both HD and LD scaffolds with and without PRP treatment. HD scaffolds displayed larger cell clusters and more extensive cell migration over time compared to LD scaffolds. However, LD scaffolds resulted a more uniform cellular distribution than HD scaffolds. Conclusion Our study demonstrates that PRP can play an important role in directing hADSCs towards fibrochondrogenic differentiation in Type I collagen-based scaffolds in vitro. Additionally, our study shows that collagen scaffold density can influence the spatial distribution and cellular behavior of infiltrated cells.

Exoskeletons designed to assist patients with activities of daily living are becoming increasingly popular, but still are subject to research. In order to gather requirements for the design of such systems, long-term gait observation of the patients over the course of multiple days in an environment of daily living are required. In this paper a wearable all-in-one data acquisition system for collecting and storing biomechanical data in everyday life is proposed. The system is designed to be cost efficient and easy to use, using off-the-shelf components and a cloud server system for centralized data storage. The measurement accuracy of the system was verified, by measuring the angle of the human knee joint at walking speeds between 3 and 12 km/h in reference to an optical motion analysis system. The acquired data was uploaded to a cloud database via a smartphone application. Verification results showed that the proposed toolchain works as desired. The system reached an RMSE from 2.9° to 8°, which is below most of the comparable system. The system provides a powerful, scalable platform for collecting and processing biomechanical data, which can help to automize the generation of an extensive database for human kinematics.

Coastal zones experience increasing climatic and human pressures, which lead to growing risks and tipping points (TPs) under future scenarios and natural resource scarcity. To avoid crossing TPs with irreversible coastal losses, this paper proposes the development of adaptation pathways based on advanced coastal oceanography and engineering knowledge that enables an objective assessment of evolving coastal risks. These pathways feature sequential interventions, combining conventional engineering works with nature-based solutions (NbS), steered by simulations and observations as a function of available coastal resources (space and sediment) and risks for infrastructure and socioeconomic assets. Such an adaptation has been developed for urban and peri-urban Mediterranean beaches, considering conventional coastal engineering together with NbS. Both types of interventions are assessed in terms of key physical variables, which serve to evaluate performance and estimate TPs. This analysis supports the new coastal protection and management plan promoted by the local government and the coastal adaptation plan of the central government. The approach and results illustrate the potential of adaptation pathways for beach sustainability, enhancing the compatibility between short/long-term coastal protection objectives under present/future climate and management scenarios. The adaptation pathways development underpins an increasing stakeholder cooperation to achieve shared decisions for coastal sustainability.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

We evaluate performance of Isogeometric analysis (IGA) for structural deformation and automobile crash. In automobile crash analysis, ensuring the accuracy of the acceleration, velocity and load in time series as well as the deformation behavior is important. To maintain the aforementioned consistency, accurately reproducing the bending and buckling of structural members is indispensable. In this study, we firstly compute the bending and buckling of structural members using IGA and validate its performance by comparing the results with conventional finite element analysis and experiments. In addition, we utilize IGA for the crash analysis of an automobile body.

Collaboration among individuals with diverse skills and personalities is crucial in producing high-quality software. The success of any software project depends on the team’s cohesive functionality and mutual complementation. This study introduces a data-centric methodology for forming Software Engineering (SE) teams centred around personality traits. Our study analyzed data from an SE course where 157 students in 31 teams worked through four project phases and were evaluated based on deliverables and instructor feedback. Using the Five Factor Model (FFM) and a variety of statistical tests, we determined that teams with higher levels of extraversion and conscientiousness and lower neuroticism consistently performed better. We examined team member interactions and developed a predictive model using extreme gradient boosting. The model achieved a 74% accuracy rate in predicting inter-member satisfaction rankings. Through graphical explainability, it underscored incompatibilities among members, notably those with differing levels of extraversion. Based on our findings, we introduce a team formation algorithm using Simulated Annealing (SA), built upon the insights from our predictive model and additional heuristics.

Geoenvironmental engineering involves defining solutions for complex problems, such as containment systems management, contaminant transport control, wastewater management, remediation of contaminated sites and valorization of geomaterials and wastes. In the last years, energy harvesting (EH) - or energy scavenging - methods and technologies have been developed to reduce the dependence on traditional energy sources, namely fossil fuels, and nuclear power, also responding to the increase of energy demands for human activities and to fulfill sustainable development goals. EH in geoenvironmental works and surrounding soil and water environment include a set of processes for capturing and accumulating energy from several sources considered deemed wasted or unusable associated to soil dynamics, stress and strain of geomaterials, hydraulic, vibrations, biochemical, light, heating and wind sources can be potential EH systems. Therefore, this work presents a review of the literature and critical analysis on the main opportunities for EH capturing, accumulating and use in geoenvironmental works, among basic electric concepts and mechanisms, analyzing those works in complex conditions involving biological, chemical, mechanical, hydraulic, and thermal coupled actions, concluding with the main investigation and challenges within geoenvironmental aspects for EH purpose.

Self-adaptive systems are capable of reconfiguring themselves while in use to reduce the risks forced by environments for which they may not have been specifically designed. Run-time validation techniques are required because complex Self-adaptive systems must consistently offer acceptable behavior for important services. The run-time testing can offer further confidence that a Self-adaptive system will continue to act as intended even when operating in unknowable circumstances. This article introduces an evolutionary framework that supports adaptive testing for Self-adaptive systems. To ensure that the adaptive systems continue to operate following its requirements and that both test plans and test cases continuously stay relevant to shifting operational conditions. The proposed approach using the SPEA2 algorithm facilitates both the execution and adaptation of run-time testing operations.

The potential of sericin, a protein derived from silkworms, is explored in bone graft applications. Sericin's biocompatibility, hydrophilic nature, and cost-effectiveness make it a promising candidate for enhancing traditional graft materials. Its antioxidant, anti-inflammatory, and UV-resistant properties contribute to a healthier bone-healing environment, and its incorporation into 3D-printed grafts could lead to personalized medical solutions. However, despite these promising attributes, there are still gaps in our understanding. The precise mechanism through which sericin influences bone cell growth and healing is not fully understood, and more comprehensive clinical trials are needed to confirm its long-term biocompatibility in humans. Furthermore, the best methods for incorporating sericin into existing graft materials are still under investigation, and potential allergic reactions or immune responses to sericin need further study.

The production of plants and crops is influenced by environmental stress, which is a serious scientific issue. Cotton is an essential crop for producing natural fibers that are used to make biofuel and edible oils. Salinity is the main element that influences cotton growth during the beginning of germination. The type of salt and the growth stage affects how sensitive a plant is to salt stress. Developing ways to enhance cotton performance in salty circumstances can be aided by an understanding of the response of cotton to salt, its mechanism of resistance, and its management methods. Osmotic and ionic imbalances originate due to the deposition of soluble salts under salinity stress in the plant's root zone. Soil salinity significantly reduces plant growth due to several factors, such as nutritional ion imbalance, which reduces K+, PO4-, and NO- absorption, excessive salt chloride concentrations, and osmotic stress, which hinders water availability. Research has revealed that compared to subsequent stages, the germination, emergence, and seedling phases are more vulnerable to salinity stress, which ultimately affects the seed cotton yield by delaying blooming, reducing fruiting positions, shedding fewer fruits, and reducing boll weight. The morphology, growth of cotton roots, shoots, yield, and fiber quality are all strongly impacted by salinity stress. It slows down plant feeding, cellular metabolism, and photosynthesis. The soil, water, and climate all affect how the plant responds to salinity stress. During salt stress, excessive exclusion of sodium or its compartmentalization is the key adaptation process in cotton. A major adaptive potential to create cotton types that can withstand salt is provided by the up-regulation of both physicochemical and non-enzymatic antioxidant genes. A successful strategy to increase cotton germination in saline soils is seed priming. Moreover, the transgenic strategy might be a viable choice for improving cotton yield in saline environments. Our review focuses on the impacts of salinity on cotton productivity as well as how plants react to salt stress. It also clarifies recent genetic advancements and molecular breeding for cotton's resistance to soil salt. To create salt-tolerant cultivars, a combination of traditional breeding and novel molecular approaches will be useful.

In this paper, a multirotor UAV platform based on the PX4 ecosystem was discussed, which in combination with the MATLAB Simulink programming environment enables utilization in various aspects of mechatronic engineering education. Extensive testing of the UAV platform control module was performed, in order to enable implementation in engineering education. In the design phase of the educational platform, take-off-the-shelf components were selected and tested, and airframe parts were manufactured using rapid prototyping technologies. The proposed educational platform with four rotors was presented and tested. The learning outcomes of the undergraduate mechatronics professional study program according to the Croatian Qualifications Framework and related to the considered platform are shown. A preliminary framework of laboratory exercises for the field of mechatronic systems control is investigated.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

The gastrointestinal and genitourinary tracts share several similarities. Primarily, these tissues are composed of hollow structures lined by an epithelium through which materials need to flow with the help of peristalsis brought by muscle contraction. In the case of the gastrointestinal tract, solid or liquid food must circulate to be digested and absorbed and the waste products eliminated. In the case of the urinary tract, the urine produced by the kidneys must flow to the bladder, where it is stored until its elimination from the body. Finally, in the case of the vagina, it must allow the evacuation of blood during menstruation, accommodate the male sexual organ during coitus, and is the natural way to birth a child. The present review describes the anatomy, pathologies and treatments of such organs, emphasizing tissue engineering strategies.

Nowadays, the Internet of Things (IoT) devices and applications have rapidly expanded worldwide due to their benefits in improving the business environment, industrial environment, and people's daily lives. However, the IoT devices are not immune to malicious network traffic, which causes potential negative consequences and sabotages IoT operating devices. Therefore, developing a method for screening network traffic is necessary to detect and classify malicious activity to mitigate its negative impacts. Therefore, this research proposes a predictive machine learning model to detect and classify network activity in an IoT system. Specifically, our model distinguishes between normal and anomaly network activity. Furthermore, it classifies network traffic into five categories, normal, Mirai attack, denial of service (DoS) attack, Scan attack, and man-in-the-middle (MITM) attack. Five supervised learning models were implemented to characterize their performance in detecting and classifying network activities for IoT systems. This includes models shallow neural networks (SNN), decision trees (DT), bagging trees (BT), support vector machine (SVM), and k-nearest neighbor (kNN). The learning models were evaluated on a new and broad dataset for IoT attacks, the IoTID20 dataset. Besides, a deep feature engineering process was applied to the dataset to improve the accuracy of the learning models. Our experimental evaluation exhibited an accuracy of 100% recorded for the detection using all implemented models and an accuracy of 99.4%-99.9% recorded for the classification process.

This paper presents a requirements specification analysis for driving the design of new systems that will allow 3D media creators to further promote and monetize from their work. The provided requirements analysis is based on the IEEE 830 standard for requirements specification. It allows us to elucidate system requirements through existing (AS-IS) and envisioned (TO-BE) scenarios affected by the latest trends on design methodologies and content promotion in social media. A total of 30 tools for content creation, promotion and monetization are reviewed. The target groups, i.e. creator groups, are divided in 10 types according to their role in 3D media production. Based on this division 10 candidate TO-BE scenarios have been identified and out of these 10 scenarios, we have selected 6 scenarios for validation by media creators. The validation was performed through a survey of 24 statements on a 5 Likert scale by 47 individuals from the domains of Media, Fine arts, Architecture, and Informatics. Useful evaluation results and comments have been collected that can be useful for future systems design.

The three-dimensional printing of scaffolds is an interesting alternative to the traditional techniques of periodontal regeneration. This technique uses computer assisted design and manufacturing after CT scan. After 3D modelling, individualized scaffolds are printed by extrusion, selective laser sintering, stereolithography, or powder bed inkjet printing. These scaffolds can be made of one or several materials such as natural polymers, synthetic polymers, or bioceramics. They can be monophasic or multiphasic and tend to recreate the architectural structure of the periodontal tissue. In order to enhance the bioactivity and have a higher regeneration, the scaffolds can be embedded with stem cells and/or growth factors. This new technique could enhance a complete periodontal regeneration. This review summarizes the application of 3D printed scaffolds in periodontal regeneration. The process, the materials and designs, the key advantages and prospects of 3D bioprinting are highlighted, providing new ideas for tissue regeneration.

This paper introduces a method for tunnel point cloud and BIM model integration and cross-section monitoring, providing information to analyse tunnel cross-sections and surrounding rock deformation, and support for tunnel maintenance and reconstruction. Three types of data are processed for the integration: laser scanning point cloud, BIM tunnel model and terrain model from oblique photogrammetry. An adaptive BIM modelling scheme is proposed for tunnels with alien structures. Precise spatial registration of the data sets is conducted by applying singular value decomposition (SVD) algorithm to calculate transformation parameters from the point cloud model to the BIM model. Since the tunnel central line has high-order derivability, a cross-section calculation method based on tangent vector is proposed to obtain the cross-sectional profile of tunnels at any mileage. The proposed method has been verified by applying it to a tunnel reconstruction project. The experiment results show that the tunnel point cloud and the BIM model were highly coincident after the integration. The developed program can effectively get the cross-section of the tunnel at any mileage, and correctly express the spatial relationship between the BIM tunnel, the point cloud of tunnel and the external mountainous terrain.

In the pre era of synthetic antibodies, pharmaceutical companies depend on finding novel drugs from medicinal plants and other traditional resources; while in present, technological advances in biology, computer and robotics give the researchers the ability to rewrite and edit DNA in order to synthesize very large sets of drug candidates; these novel and improved candidates serves the basis for creating another library of drug candidates and so on until we find the right biomolecule for the disease of interest. all these technologies combined together to synthesize therapeutic antibodies for many types of cancer, autoimmune diseases, and infectious diseases, that can address diseases much more readily to very rapidly get therapeutics into patients so that we can potentially have an impact on disease. The antibodies mechanism is recognize and bind to disease cells and pinpoint the immune system to attack those cells effectively. Now a days, they dependent on computational approach to guide and accelerate the process of antibodies engineering by combination of selection system and use of high-throughput data acquisition and analysis to build and construct populations of next generation antibodies that are thermo-stable, non-immunogenic as possible, and to be administered to many humans as possible. In this review, I will discuss the latest in silico methods for antibodies engineering.

Preparing high school students for engineering disciplines is crucial for sustainable scientific and technological developments in the USA. This paper discusses a pre-college program, which not only exposes students to various engineering disciplines but also enables them to consider engineering as the profession. The four-week long “Engineering Innovation (EI)” course is offered every year to high school students by the center of outreach, Johns Hopkins University. EI program is designed to develop problem-solving skills through extensive hands-on engineering experiments. A team consisting of an instructor, generally a PhD in Engineering, and a teaching fellow, generally a high school science teacher, closely work with students to pedagogically inculcate basics of core engineering disciplines such as civil, mechanical, electrical, materials, and chemical engineering. EI values independent problem-solving skills and simultaneously promote the team spirit among students. A number of crucial engineering aspects such as professional ethics, communications, technical writing, and understanding of common engineering principles are inculcated among high school students via well-designed individual and group activities. This paper discusses the model of EI program and its impact on students learning and their preparation for the engineering career.

Abstract: The broad clinical use of synthetic vascular grafts for vascular diseases is limited by their thrombogenicity and low patency rate, especially for vessels with a diameter inferior to 6 mm. Alternatives such as tissue-engineered blood grafts (TEBGs) have gained increasing interest. Among the different manufacturing approaches, 3D bioprinting presents numerous advantages and enables the fabrication of multi-scale, multi-material, and multicellular tissues with heterogeneous and functional intrinsic structures. Extrusion-, inkjet- and light-based 3D printing techniques have been used for the fabrication of TEBG out of hydrogels, cells, and/or solid polymers. This review discusses the state-of-the-art research on the use of 3D printing for TEBG with a focus on the biomaterials and deposition methods.

Literature review indicates that the basic microstructure of Ti-6Al-4V is bimodal which consist of two phases: α + β, and it occurs after the fabrication in conventional methods such as casting, plastic forming or machining processes. After the additive manufacturing methods, there could be significant changes in the microstructure. Due to the rapid heat exchange during heat-treatment process, bimodal microstructure transforms into lamellar microstructure which consists of two phases α′ + β. Despite applying optimum printing parameters, 3D-printed products exhibit typical surface defects and discontinuities. Recently, two of the primary technologies for the improvement of surface layer properties of titanium alloys are shot peening and electropolishing. Literature review signalizes that shot peening and electropolishing processes have positive impact on the corrosion behaviour, mechanical properties and the condition of the surface layer of titanium alloy. Furthermore, there is a lack of studies about combining shot peening and electropolishing in one hybrid process on titanium alloys, which could synthesize the benefits of both processes. The scope of future investigation is also included in this review.

Bone tissue engineering has been developed in the past decades, with the engineering of bone substitutes on the vanguard of this regenerative approach. PCL based scaffolds are fairly applied for bone regeneration, and several composites have been incorporated, as to improve the devices’ mechanical properties and tissue ingrowth. In this study, HA was incorporated on PCL based scaffolds with two different proportions, 80:20 and 60:40. Devices were produced with two different techniques, SC and MB, and further investigated with regards to their mechanical characteristics and in vitro cytocompatibility. Results show the MB devices to present more promising mechanical properties, along with the incorporation of HA. The latter is also related to an increase in osteogenic activity and promotion. Overall, this study suggest PCL:HA scaffolds to be promising candidates for bone tissue engineering, particularly when produced by the MB method.

Abstract: The promise of regenerative medicine and tissue engineering is founded on the ability to regenerate diseased or damaged tissues and organs into functional tissues and organs or the creation of new tissues and organs altogether. In theory, all damaged and diseased tissues and organs can be regenerated or created using different configurations and combinations of extracellular matrix, cells and inductive biomolecules. Currently, regenerative medicine and tissue engineering can allow the improvement of patients’ quality of life through availing novel treatment options. Tissues and organs have a specific ECM, with specific proteins and factors released by cells residing within the local microenvironment. The coupling of regenerative medicine and tissue engineering field with 3D printing is revolutionizing the treatment of patients in a huge way. 3D bioprinting allows the proper placement of cells and ECMs, allowing the recapitulation of native microenvironments of tissues and organs. 3D bioprinting utilizes different bioinks made up of different formulations of ECM/biomaterials, biomolecules and even cells. The choice of the bioink used during 3D bioprinting is very important as properties such as printability, compatibility and physical strength influence the final construct printed. The extracellular matrix (ECM) provides both physical and mechanical microenvironment needed by cells to survive and proliferate. Decellularized ECM bioink contains biochemical cues from the original native ECM and also the right proportions of ECM proteins. Different techniques and characterization methods are used to derive bioinks from several tissues and organs and to evaluate their quality. This review discusses the uses of decellularized ECM bioinks and argues that they represent the most biomimetic bioinks available. In addition, we briefly discuss some polymer-based bioinks utilized in 3D bioprinting.