GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

Two types of trenches cross-section in conventional vertical and brand new reverse-V-shape have fabricated on SCD substrate by micro-jet water-assist laser, the epitaxial lateral overgrowth technique has applied by microwave plasma chemical vapor deposition system in forming multiple micrometer-size channels. Raman and SEM techniques have applied in analyze both types growth layer characterization. Optical microscope has used to test microchannels hollowness. As a result, with the brand new reverse-V-shape trench, epitaxial lateral overgrowth layer reaches higher SCD surface morphology and crystal quality.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

We review recent work on narrowband orthogonally polarized optical RF single sideband generators as well as dual-channel equalization, both based on high-Q integrated ring resonators. The devices operate in the optical telecommunications C-band and enable RF operation over a range of either fixed or thermally tuneable frequencies. They operate via TE/TM mode birefringence in the resonator. We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization for both the fixed and tunable devices.

This paper presents a novel micro-segmented genetic algorithm (μsGA) to identify the best solution for the locomotion of a quadruped robot designed on a rectangular ABS plastic platform. We compare our algorithm with three similar algorithms found in the specialized literature: a standard genetic algorithm (GA), a micro-genetic algorithm (μGA), and a micro artificial immune system (μAIS). The quadruped robot prototype guarantees the same conditions for each test. The platform was developed using 3D printing for the structure and can accommodate the mechanisms, sensors, servomechanisms as actuators. It also has an internal battery and a multicore embedded system (mES) to process and control the robot locomotion. This research proposes a μsGA that segments the individual into specific bytes. μGA techniques are applied to each segment to reduce the processing time; the same benefits as the GA are obtained, while the use of a computer and the high computational resources characteristic of the GA are avoided. This is the reason why some research in robot locomotion is limited to simulation. The results show that the performance of μsGA is better than the three other algorithms (GA, μGA and AIS). The processing time was reduced using a mES architecture that enables parallel processing, meaning that the requirements for resources and memory were reduced. This research solves the problem of continuous locomotion of a quadruped robot, and gives a feasible solution with real performance parameters using a μsGA bio-micro algorithm and a mES architecture.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Various natural disasters such as floods, fires, earthquakes, etc. have affected human life. Detection and classification of large and small earthquakes caused by natural or abnormal events have been always important to Earth scientist. One of the most important research challenges in this field is the lack of an effective method for identifying and categorizing various types of seismic events at less important and important levels. Based on latest achievements of Data Mining international institutions such as Rexer-KDnugget-Gartner and also newest authentic articles, SVM, KNN, C4.5, MLP are from most important and popular and leading classifiers in data world.Therefor in present study, a boost learning system consisting support vector machine algorithms with linear regression, MLP Neural Network ، C4.5 decision tree and KNN near neighborhood have been utilized in a combined form to detect and categorize micro seismic events. In general, the steps involved in the proposed method are: 1) performing artificial seismic tests, 2) data gathering and analysis, 3) conducting preprocessing and separating training and testing samples, 4) generating relevant models with training samples and detecting and categorizing test samples and 5) extracting a cluster with the maximum candidate using boost learning. After simulations, it was observed that the accuracy of proposed boost method to the best answer was about 6.1% higher compare to other methods and the error rate was 0.082% of recalling. Accuracy of detection and classification to the best answer were also improved compare to other methods up to 2.31% and 6.34%, respectively.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

Pandemics, and other risk-related contexts, require dynamic changes in behavior as situations develop. Human behavior is influenced by both explicit (cognitive) and implicit (intuitive) factors. In this study, we used psychological distance as a lens to understand what influences our decision-making with regards to risk in the context of COVID-19. The study was based on the rationale that our relational needs are more concrete to us than the risk of the virus. First, we explored the impact of social-psychological distance on participants’ risk perceptions and behavioral willingness. As hypothesized, we found that close social relationships of agents promoted willingness to engage in risky behavior. In the second phase, we tested an intervention designed to increase the concreteness of information about virus transmission as a mechanism to mitigate the bias of social influence. We found that the concreteness intervention resulted in significantly reduced willingness to engage in risky behavior. As such, communications aimed at changing the behavior of citizens during times of increased risk or danger, should consider conceptually concrete messaging when communicating complex risk, and hence may provide a valuable tool in promoting health-related behavior.

Cities are important sources of anthropogenic methane emissions. Municipal governments can play a role in reducing those emissions to support climate change mitigation, but they need information on the rate of emissions to context mitigation actions and track progress. Here, we examine the application of satellite data from the TROPOspheric Monitoring Instrument (TROPOMI) to estimate city-level methane emissions rates in a case study of the City of Calgary, Alberta, Canada. While satellites are touted as a global methane monitoring system, we found limited observational coverage over Calgary that precluded the reliability of measurement-based models to track the annual emissions. In this work, we integrated valid observations over three years (2020-22) and used mass balance modeling to derive a long-term averaged emission estimate. The column-averaged dry-air mole fraction (XCH4) enhancement over Calgary was small, 4.7 ppb, but within the city boundary, we identified local hot spots in the vicinity of known sources (wastewater treatment facility and landfills). The city-scale emissions estimate from mass balance was 215.4 ± 132.8 t/d CH4. This estimate is approximately four- and six-times larger than estimates from Canada's gridded national inventory report of anthropogenic CH4 emissions and the Emissions Database for Global Atmospheric Research (EDGAR v8.0), respectively. Valid observations are more common in warmer months and occur during a narrow daily overpass timeslot over Calgary – these effects may bias the emissions estimate. Overall, the findings from this case study highlight the challenge of deriving routine (sub-annual to annual) satellite-based estimates of city-scale methane emissions in similar geographic settings and suggest that more granular emissions inventories are needed to improve methane reporting.

Infrastructure and urban network operators, city users and industrialists are faced with complex issues to ensure the sustainability of the service, maintain, operate and develop their urban systems, while integrating environmental, economic and societal impacts and being resilient to unexpected geopolitical and climatic upheavals. Digital Twins are now recognized as the cornerstone of digital transformation. In the field of smart cities, they can enable all stakeholders to collaborate across disciplinary silos and foster digital transformation in urban and territorial projects to ensure sustainability, resilience and increased inventiveness. However, the application of the Digital Twin technology to Smart Cities lacks of standards. This paper proposes a high-level architecture for Digital Twins as an enabler of various levels of interoperation between key stakeholders of a Smart City. Such a technology-agnostic architecture, when implemented for a given Smart City, produces a middleware for large scale interoperability between actors involved in multiple supply chains of this territory.

Emotional intelligence and educational level are commonly associated with success in life and well-being. While multiple studies have explored these concepts independently, few studies have examined the impact of educational level on emotional intelligence and associated variables, such as well-being. A total of N = 202 participants were recruited online. Participants completed measures of emotional intelligence, well-being (i.e., happiness, self-esteem, personal growth). Overall, participants who previously obtained a bachelor’s degree displayed higher levels of emotional intelligence, happiness, self-esteem, and personal growth compared to those without an undergraduate degree. However, no differences were observed on any variable between individuals currently enrolled in a university and non-students. The results suggest that, while completing a university degree increases emotional intelligence and well-being, the stress of being a student may negatively impact the benefits obtained from attending university. Limitations and possible directions for future research are discussed.

Sediment thickness increases can cause floodplains and the water level increases. This has the potential to generate a flood. Using electromagnetic waves, Time Domain Electromagnetic (TDEM) detected resistivity or conductivity contrast of lithology in the subsurface. It is measured in the time domain. TDEM method has been developing for decades. Here we tried to develop a 1-D forward modelling program for central loop configuration in the water environment using the Adaptive Born Forward Mapping (ABFM) method. We simulated this program in several water environment conditions (such as freshwater, brackish water and saline water) to know its response. Preventing natural hazards, especially flood hazards which are caused by the floodplain increases is our motivation in this research. Our simulation shows that Central-Loop Configuration Time-Domain Electromagnetic Method is able for imaging the sediment thickness clearly. The response of this method is extremely sensitive in saline water to depth changing than in other water environments.

The national study analyzes sea level rise (SLR) impacts based on 36 different SLR and storm surge scenarios across 5.7 million geographic locations and 3 time periods. Taking an approach based on engineering design guidelines and current cost estimates, the study details projected cost impacts for states, counties, and cities. These impacts are presented from multiple perspectives including total cost, cost per-capita, and cost per-square mile. The purpose of the study is to identify specific locations where infrastructure is vulnerable to rising sea levels. The study finds that Sea Level Rise (SLR) and minimal storm surge is a $400 billion threat to the United States by 2040 that includes a need for at least 50,000 miles of protective barriers. The research is limited in its scope to protecting coastal infrastructure with sea walls. Additional methods exist and may be appropriate in individual situations. The study is original in that it is a national effort to identify infrastructure that is vulnerable as well as the cost associated with protecting this infrastructure.

Pain is an unpleasant emotional and sensory experience. For many years orthodontists have been looking for an effective method of reducing this feeling of discomfort. In recent years, low-level laser therapy (LLLT) has taken hold in the orthodontic field. Among the countless advantages it can modulate the painful feeling. The aim of this research is to identify the use of photobiomodulation in subjects undergoing fixed orthodontic treatment, to reduce the pain and discomfort that it causes. The research was conducted from the Web of Science, Pubmed and Scopus databases. Only 14 of all articles met the inclusion and exclusion criteria and were therefore used to conduct the research. The different studies compared, in most cases, patients whose mouth was divided into a part treated with laser therapy and a placebo part. The results show a statistically significant difference in perceived pain between the irradiated arch and the non-irradiated arch. Three authors didn’t find statistically significant results in favour of low-laser therapy, but it is important to remember that they used different parameters. To obtain generally valid studies, with consistent and reproducible results, it is necessary to standardize the different parameters used that are independent by operator performing the procedure.

The majority of urban inhabitants in low- and middle-income country (LMIC) cities live in deprived urban areas. However, statistics and data (e.g., local monitoring of Sustainable Development Goals - SDGs) are hindered by the unavailability of spatial data at metropolitan, city and sub-city scales. Deprivation is a complex and multidimensional concept, which has been captured in existing literature with a strong focus on household-level deprivation while giving limited attention to area-level deprivation. Within this scoping review, we build on existing literature on household- as well as area-level deprivation frameworks to arrive at a combined understanding of how urban deprivation is defined with a focus on LMIC cities. The scoping review was enriched with local stakeholder workshops in LMIC cities to arrive at our framework of Domains of Deprivations, splitting deprivation into three different scales and nine domains. (1) Socio-Economic Status and (2) Housing Domains (Household scale); (3) Social Hazards & Assets, (4) Physical Hazards & Assets, (5) Unplanned Urbanization and (6) Contamination (Within Area scale); and (7) Infrastructure, (8) Facilities & Services and (9) city Governance (Area Connect scale). The Domains of Deprivation framework provides a clear guidance for collecting data on various aspects of deprivation, while providing the flexibility to decide at city level which indicators are most relevant to explain individual domains. The framework provides a conceptual and operational base for the Integrated Deprived Area Mapping System (IDEAMAPS) Project for the creation of a data ecosystem, which facilitates the production of routine, accurate maps of deprived “slum” areas at scale across cities in LMICs. The Domains of Deprivation Framework is designed to support diverse health, poverty, and development initiatives globally to characterize and address deprivation in LMIC cities.

Sea-level rise is a problem increasingly affecting coastal areas worldwide. The existence of Free and Open-Source Models to estimate the sea-level impact can contribute to better coastal man-agement. This study aims to develop and to validate two different models to predict the sea-level rise impact supported by Google Earth Engine (GEE) – a cloud-based platform for planetary-scale environmental data analysis. The first model is a Bathtub Model based on the uncertainty of projections of the Sea-level Rise Impact Module of TerrSet - Geospatial Monitoring and Modeling System software. The validation process performed in the Rio Grande do Sul coastal plain (S Brazil) resulted in correlations from 0.75 to 1.00. The second model uses Bruun Rule formula implemented in GEE and is capable to determine the coastline retreat of a profile through the creation of a simple vector line from topo-bathymetric data. The model shows a very high cor-relation (0.97) with a classical Bruun Rule study performed in Aveiro coast (NW Portugal). The GEE platform seems to be an important tool for coastal management. The models developed have been openly shared, enabling the continuous improvement of the code by the scientific commu-nity.

Sea-level rise is a problem increasingly affecting coastal areas worldwide. The existence 15 of Free and Open-Source Models to estimate the sea-level impact can contribute to better coastal 16 management. This study aims to develop and to validate two different models to predict the 17 sea-level rise impact supported by Google Earth Engine (GEE) – a cloud-based platform for plan-18 etary-scale environmental data analysis. The first model is a Bathtub Model based on the uncer-19 tainty of projections of the Sea-level Rise Impact Module of TerrSet - Geospatial Monitoring and 20 Modeling System software. The validation process performed in the Rio Grande do Sul coastal 21 plain (S Brazil) resulted in correlations from 0.75 to 1.00. The second model uses Bruun Rule for-22 mula implemented in GEE and is capable to determine the coastline retreat of a profile through the 23 creation of a simple vector line from topo-bathymetric data. The model shows a very high correla-24 tion (0.97) with a classical Bruun Rule study performed in Aveiro coast (NW Portugal). The GEE 25 platform seems to be an important tool for coastal management. The models developed have been 26 openly shared, enabling the continuous improvement of the code by the scientific community.

Failure to adapt to climate change is currently considered one of the major threats affecting humanity. Hence, much effort is being put into discussing adaptation approaches. While many adaptation options have been identified, the academic literature does not present a simple process that local councils and community members can use to rank adaptation options. In this context, community members participating on planning processes are presented with many adaptation options, but with no objective approach for selection, which adds challenge to the planning process. With the objective of addressing this issue, this work proposes a simple equation that allows calculating the applicability level of adaptation options. Results can then be plotted into graphs that allow correlating adaptation options and applicability level, which can be easily understood by community members. To develop such equation, this work built on existing sophisticated models from where the indicators used on the equation were identified, as well as the relationship between them. A scale was proposed to help on identifying adaptation options that should be implemented on the short, medium and long term, and options that should only be implemented if the circumstance change.

Modern Monte-Carlo-based rendering systems still suffer from the computational complexity involved in the generation of noise-free images, making it challenging to synthesize interactive previews. We present a framework suited for rendering such previews of static scenes using a caching technique that builds upon a linkless octree. Our approach allows for memory-efficient storage and constant-time lookup to cache diffuse illumination at multiple hitpoints along the traced paths. Non-diffuse surfaces are dealt with in a hybrid way in order to reconstruct view-dependent illumination while maintaining interactive frame rates. By evaluating the visual fidelity against ground truth sequences and by benchmarking, we show that our approach compares well to low-noise path traced results, but with a greatly reduced computational complexity allowing for interactive frame rates. This way, our caching technique provides a useful tool for global illumination previews and multi-view rendering.

Academic staffs’ organizational commitment has been a critical issue to determine work performance for successes of University, as well as, to keep its Academic staffs motivation granted for achieving better work performance. This subject has therefore, been investigated so as to draw attention for enhancement of effective work performance and success. The main objective of this study was to assess academic staffs’ level of organizational commitment in Haramaya University. The study also investigated whether significant differences exist in academic staffs’ level of organizational commitment in reference to their gender and level of education. Researchers used cross-sectional research design. Primary and secondary data sources were used to study the problem. A commitment scale questionnaire was used to collect data from 275 participants who were selected from 877 target population of the study using stratified sampling technique; furthermore, focus group discussion and document review were also used to triangulate the data. The quantitative data were analyzed using both descriptive and inferential statistics; the qualitative data were also analyzed using narration methods of analysis. The study revealed that academic staffs of the university have moderate level organizational commitment. This implies relatively no more expected effective work performance for success of the institution; In addition, there were relative implications of turnover, turnover intention, absenteeism, and demotivation among staffs. The study further revealed that although there is no significance difference in employees’ level of commitment with reference to gender, their level of organizational commitment was significantly different in reference to level of education.

Multigranulation is a new approach to the Rough Set Theory, where several separability relationships are used to obtain different granulations of the universe. The Multigranulation starts from the existence of different contexts or subsets of features to characterize the objects of the universe. In this paper, a method for the generation of contexts from the construction of similarity relations is proposed.The proposed solution was evaluated in an international database using the KNN classifier. It was also applied in the solution of a real problem in Civil Engineering specifically in Traffic Engineering, the contexts generated from the proposal used to determine the features of higher incidence in the service level of the road. The results achieved both in the international database and in the proposed application demonstrate the applicability of the proposed method.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

In the field of agricultural food production, the transition between organic and inorganic farming methods has been an issue of much debate. The debate, on one hand, stresses the urgency for the transition in order to preserve environment and health; and, on the other hand, emphasizes the pressure of maintaining food production for a large growing population. Thus, the dilemma is how to find an agricultural system that would balance between obtaining food security and ensuring a safe sustainably environment-friendly food production system. This article focuses on the debate, in the context of Bangladesh, and questions whether it is the proper time, and stage in the development process, to attempt the transition from inorganic conventional food production methods to organic food production methods. This article contemplates why the organic rice market is not expanding in Bangladesh, and attempts to explain the slow growth of the market through the two main factors of income constraint and lack of awareness among people about the environmental and health detriments of inorganic farming methods. The study is exploratory in nature, and finds that it is not mainly the lack of awareness but the income constraint that can be principally attributed to the slow expansion of the organic rice market in Bangladesh. Through exploring consumers’ awareness about organic farming methods and their demand for organic products, this study shows how income as the major constraint, besides price, affects consumers demand for organic and inorganic rice in Bangladesh. Income being identified as the major barrier reveals the potential of the organic rice market to grow in the future, as Bangladesh continues its journey towards becoming a middle-income country.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

Cross-border e-commerce is an opportunity for micro, small and medium sized enterprise (MSMEs) in developing countries. Based on a resource-based approach, this research studied how to support resource lacking enterprises with export marketing strategy. It dealt with actual business cases of Mongolian entrepreneurs trying to export Mongolian products to Korean market. Multiple source data including interviews, internal documents, and group discussions, were matched with theories to come up with strategies and validated by supporting organizations in Mongolia and Korea. The research suggests that MSMEs should rely on third party digital platforms rather than setting up their own. For product strtategy of the marketing mix, sellecting competitive product categories and supporting them adjusting to foreign markets and quality assurance is needed. For price strategy, loccally high priced products should use a price penetration strategy with a lower price compared to competing foreign products. For place strategy, supporting organizations should partner with exporters for collective delivery. For promotion strategy, they need to support the capacity of MSMEs enabling them to use digital marketing tools effectivly. These strategies were validated and adopted by supporting organizations in Monglia and Korea.

Micro elastofluidics is a transformative branch of microfluidics, leveraging fluid-structure interaction (FSI) at the microscale to enhance the functionality and efficiency of various microdevices. This review paper elucidates the critical role of advanced computational FSI methods in the field of micro elastofluidics. By focusing on the interplay between fluid mechanics and structural responses, these computational methods facilitate the intricate design and optimisation of microdevices such as microvalves, micropumps, and micromixers, which rely on the precise control of fluidic and structural dynamics. In addition, these computational tools extend to the development of biomedical devices, enabling precise particle manipulation and enhancing therapeutic outcomes in cardiovascular applications. Furthermore, this paper addresses the current challenges in computational FSI and highlights the necessity for further development of tools to tackle complex, time-dependent models under microfluidic environments and varying conditions. Our review highlights the expanding potential of FSI in micro elastofluidics, offering a roadmap for future research and development in this promising area.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross sections and high optical quality. This is particularly challenging for spatially-constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in SZ2080™polymer with photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modeling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Road traffic transportation has flourished in the process of urbanization by its advantages, but it also produces harmful environmental vibrations. The vibration problem is especially significant for production workshops with precision instruments. A field measurement was conducted to analyze the source characteristics and propagation laws of traffic-induced vibrations. Off the northern side of an urban highway lies a microelectronics workshop. When a large truck passes by, both the vibration responses on the ground and in the workshop considerably increase. Greater vibration is produced in the vertical direction than in the X and Y axes. The predominant frequency band of the vibration response caused by road traffic vehicles is lower than 20 Hz. The vertical vibration responses of the first and second floors in the workshop greatly exceed the VC-C limit because of the high daily traffic flow. Attribute to the excitation of the operation of the manufacturing equipment on the second floor, the vertical vibration level of the second floor is essentially higher than that of the first floor. Therefore, it is impossible to disregard the micro-vibration in the workplace produced by the manufacturing machinery as well as the ex-citement of the road traffic. The measured data can be used to test potential numerical models for forecasting vibrations caused by traffic on roads as well as to guide vibration assessment work throughout the planning and design stages of roads.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

This paper presents a novel dynamic camera parameter control method for position and posture estimation of highly miniaturized AR markers (micro AR markers) using a low cost general camera. The proposed method performs iterative calculation of the marker’s position and posture to converge them to specified accuracy with dynamically updating the camera’s zoom, focus and other parameter values based on the detected marker’s depth distances. For a 10 mm square micro AR marker, the proposed system demonstrated recognition accuracy of better than ±1.0% for depth distance and 2.5∘ for posture angle with a maximum recognition range of 1.0 m. In addition, the iterative calculation time was at most 0.7 seconds in an initial detection of the marker. These experimental results suggest that the proposed method and system can be applied to a robotic precise handling of small objects with low cost.

The genus Eucalyptus is a globally captivated source of hardwood and is well known for its medicinal uses. The hybrid and wild species of Eucalyptus are widely used as exotic plantations due to their renowned potential of adapting to various systems and sites, furthermore, making the species the most extensively propagated. Despite unquestionable progression in biotechnological and tissue culture approaches, the productivity of plantations is still limited often due to the low efficiency of clonal propagation from cuttings. The obtained F1 hybrids yield high biomass and High-quality low-cost raw material for large-scale production, however, the development of hybrid, clonal multiplication, proliferation, and post-developmental studies are still major concerns. This riveting review describes the problems concerned with in-vitro and clonal propagation of Eucalypt plantation; recent advances in biotechnological and tissue culture practices for massive and rapid micro-propagation of Eucalyptus; as well, highlights the Eucalypt germplasm preservation techniques.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

The purpose of this review is to present the current role of ultrasound-based techniques in the diagnostic pathway of prostate cancer (PCa). With overdiagnosis and overtreatment of a clinically insignificant PCa over the past years, multiparametric magnetic resonance imaging (mpMRI) became recommended for every patient suspected of PCa before performing a biopsy. It enabled targeted sampling of the suspicious prostate regions, improving the accuracy of the traditional systematic biopsy. However, mpMRI is associated with high costs, relatively low availability, long and separate procedure or exposure to the contrast agent. The novel ultrasound modalities such as shear wave elastography (SWE), contrast-enhanced ultrasound (CEUS) or high frequency micro-ultrasound (MicroUS) may be capable of maintaining the performance of mpMRI without its limitations. Moreover, the real-time lesion visualization during biopsy would significantly simplify the diagnostic process. Another value of these new techniques is the ability to enhance the performance of mpMRI by creating the image fusion of multiple modalities. Such models might be further analyzed by artificial intelligence to mark the regions of interest for investigators and help to decide about the biopsy indications. The dynamic development and promising results of new ultrasound-based techniques should encourage researchers to thoroughly study their utilization in prostate imaging.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

ST-elevation myocardial infarction (STEMI) remains one of the leading causes of morbidity and mortality worldwide. The identification of novel metabolic and imaging biomarkers could unveil key pathophysiological mechanisms at the molecular level and promote personalized care in patients with acute coronary syndromes. We studied 38 patients with STEMI who underwent primary percutaneous coronary intervention and thrombus aspiration. We sought to correlate serum ceramide levels with micro-CT quantified aspirated thrombus volume and relevant angiographic outcomes, including modified TIMI thrombus grade and pre- or post-procedural TIMI flow. Higher ceramide C16:0 levels were significantly, but weakly correlated with larger aspirated thrombus volume (Spearman r=0.326, p=0.046), larger intracoronary thrombus burden (Nagelkerke R2=0.236, p=0.030) and worse pre- and post-procedural TIMI flow (Nagelkerke R2=0.210; p=0.049 and Nagelkerke R2=0.277; p=0.039, respectively). Ceramides C24:0 and C24:1 were also significantly associated with larger intracoronary thrombus burden (Nagelkerke R2=0.311; p=0.008 and Nagelkerke R2=0.423; p=0.001, respectively). In conclusion, serum ceramide levels (mainly C16:0 and C24:1) were higher among patients with larger intracoronary and aspirated thrombus burden. This suggests that quantification of serum ceramides might improve risk-stratification of patients with STEMI and facilitate a more individualized approach in everyday clinical practice.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

Diabetes is one of the metabolic syndromes that demands the great concern affecting millions of people all over the world. Viral infections were also considered as responsible for diabetes. Though, variety of medications for prevention and treatment of diabetes are available, numerous limitations are also prevailing that cannot be neglected. Precise drug-targetability, controlled drug-release, oral bioavailability, minimizing side effects are a few to consider. To address most of these shortcomings of traditional drug-delivery models, nanoformulation has been employed therein a wide range of nanoformulation models are developed. The pharmacology of a drug can be greatly enhanced through nanoformulation models in diabetes treatment in terms of enhanced bioavailability, prolonged and sustained drug-lease, maintain maximum drug concentration in serum, higher intestinal absorption, and protection from enzymatic degradation. In this review work, recently designed nanoformulation models for efficient insulin delivery and the other properties concerning diabetes such as reducing blood glucose level, total cholesterol, triglycerides, lipid profile, wound healing, elevating antioxidant enzymes etc. are discussed. Classification of the nanoformulation models is done based on the nature of the fabricating material employed in nanoformulation. This review may be helpful in designing a more efficient nanoformulation model for diabetes treatment.

This paper utilizes the 2020 financial data of A-share listed companies, both ST and non-ST, as the data sample. The model is constructed employing the Factor-Logistic fusion algorithm. Eight key indicator factors were selected from the frameworks of profitability, solvency, operating capacity, development potential, shareholder retained earnings, cash flow and asset growth. An independent indicator system was subsequently established to address the issue of collinearity among risk indicators. The results of model are presented in the form of probabilities, enhancing the interpretability of model. The weights of the features indicate the influence of different features on the final outcome. The model achieves a prediction accuracy of over 89%, with an AUC score exceeding 95%. Finally, by applying the principles of interval estimation theory in statistical hypothesis testing, the risk levels are categorized as A-level representing significant risk, B-level representing moderate risk, C-level representing minor risk and D-level representing no risk. This paper aims to provide a comprehensive definition of a universal financial risk management warning model for enterprises, applicable to all enterprises in China.

Keywords: green spaces, NDVI, level of greenness, urban environment, Aktobe

The development of U.S. Army and NATO data link systems is introduced first, and then the development trend of future intelligent data link is summarized into integration, generalization, multifunctionality and high security. A unit-level combat system architecture based on the global combat cloud, which is capable of realizing the flexible scheduling of global combat resources and maximizing the overall combat effectiveness, is proposed. Intelligent data link is an important part of this solution, providing strong information support for future urban unit-level warfare.

Abstract: Rural digital governance is an inevitable requirement to improve the efficiency of rural governance, and is also an important means to realize the modernization of rural governance. In the context of the digital rural development strategy, the index measurement system of rural digital governance level is built around five key governance areas of "digital economy, digital ecology, digital culture, digital people's livelihood, and digital government affairs". The entropy weight Topsis model is used to measure and evaluate the level of rural digital governance in 31 provinces in China in 2021. The results show that there is a large gap in the level of digital governance in China's counties and villages, and the level of each region presents a decreasing spatial distribution from "east - middle - west". In terms of digital economy, the eastern region has a high score and good development, while the central and western regions have poor development. In terms of digital ecology, only the eastern region is higher than the national average; In terms of digital culture, only the central region is higher than the national average; In terms of digital livelihood and digital government, the central and eastern regions are slightly higher than the national average; The top three provinces in overall scores are Zhejiang, Guangdong and Jiangsu.

Flood disasters have become an annual occurrence along the East Coast of North Sumatra (ECNS) and Medan City. Numerous studies have examined the causal factors flood disasters in this area, such as changes in land use, drainage issues, and population growth, but the intensity of flood disasters continues to rise. In this research, we focused on evaluating the unexplored factors of land subsidence and rising sea levels in this region. Our investigation uses multi-sensor satellite data and field surveys to conduct an assessment of the rate of land subsidence and sea level rise and assess their implications on flood disasters. This study highlights the potential of multi-sensor satellite data as a primary resource for assessing flood disasters in coastal areas and densely populated large cities. Furthermore, we propose a solution to reduce the negative impact of flood disasters by by engaging local communities and environmental enthusiasts in mangrove reforestation along the coastline.

The creation of crop-type maps from satellite data has proven challenging, often impeded by a lack of accurate in-situ data. This paper aims to demonstrate a method for crop-type (ie. Maize, Wheat and Other) recognition based on Convolutional Neural Networks using a bottom-up approach. We trained the model with a highly accurate dataset of crowdsourced labelled street-level imagery. Classification results achieved an AUC of 0.87 for wheat, 0.85 for maize and 0.73 for other. Given that wheat and maize are the two most common food crops globally, combined with an ever-increasing amount of available street-level imagery, this approach could help address the need for improved crop-type monitoring globally. Challenges remain in addressing the noisy aspect of street-level imagery (ie. buildings, hedgerows, automobiles, etc.), where a variety of different objects tend to restrict the view and confound the algorithms

Smoking have been linked to male infertility by affecting the sperm epigenome and genome. In this study, we aimed to determine possible changes in the transcript levels of the PTPRN2, PGAM5, and TYRO3 genes in heavy smokers compared with non-smokers; and to investigate their association with fundamental sperm parameters. One hundred eighteen sperm samples (63 heavy-smokers (G1) and 55 non-smokers (G2) were included in this study. Semen analysis was performed according to WHO guidelines. After total RNA extraction, RT-PCR was used to quantify the transcript levels of studied genes. In G1 a significant decrease in standard semen parameters in comparison to non-smokers has been shown (p<0.05). Moreover, PGAM5 and PTPRN2 were differentially expressed (P≤0.03 and P≤0.01, respectively), and downregulated in spermatozoa of G1 compared to G2. In contrast, no difference was observed for TYRO3 (p≤0.3). In G1, mRNA expression level of studied genes correlated negatively with motility, sperm count, normal form, vitality, and sperm membrane integrity (p<0.05). Therefore, smoking may affect gene expression and male fertility by altering DNA methylation patterns in genes associated with fertility and sperm quality, including PGAM5, PTPRN2, and TYRO3.

Memristor has attracted a lot of interest due to its high processing speed, low power consumption and high integration ability, which is critical for electronic systems and memory-centric computing. However, the memristor programming circuit and strategy are still inflexible and complex, since the signal generator/collector and stimulate pulse must be carefully matched and designed based on memristor intrinsic characteristics without reconfigurable. Here, a simple and effective circuit only consists a parallel reference-resistor-and-NMOS is designed to program memristor with a more than 99% memristance precision. And the amplitude and width of stimulate pulse are fixed to ±4V and 5ms, respectively. In order to cope with the device variation, such as ±10% tolerance of transition voltage, an optimized programming strategy was proposed and demonstrated great robustness. Additionally, a set of reference resistors and NMOSs have been added to facilitate multi-level memristance operation without requiring any changes to the circuit structure. This program circuit was also employed to program memristor crossbar remains 99% precision. In the end, a memristor-based convolutional neural network which controlled by our optimized programming circuit was used for image recognition, and 89.36% accuracy can be achieved even under 15.8% memristance tolerance. This novel circuit demonstrates a simple and flexible strategy in memristor programming, providing a new way to control memristor crossbar for practical application.

Structured extraction of emergency event information can effectively enhance the ability to re-spond to emergency events. This article focuses on the extraction of Chinese document-level emergency events, which mainly faces two key issues in this field: first, related datasets; Secondly, existing DEE (document-level event extraction) studies mostly use sequence annotation to extract candidate entities in the subtask of candidate entity extraction without considering the problem of role overlapping between candidate entities. On the one hand, this article constructs a Chinese document-level emergency extraction dataset, CDEEE, which first annotates the issues of argu-ment scattering, multiple events, and role overlapping. On the other hand, this article proposes a model RODEE for the problem of role overlapping in DEE tasks. This model first uses two in-dependent modules to represent the head and tail positions of candidate entities, then uses a multiplication attention mechanism to interact with the two to obtain a scoring matrix. Finally, role-overlapping candidate entities are predicted to assist in completing DEE tasks. Experiments were conducted on our manually annotated dataset, CDEEE, and the results showed that RODEE can effectively solve the problem of role overlapping in candidate entities and improve the performance of the DEE model.

When there is uncertainty in the value of parameters of the input random components of a stochastic simulation model, two-level nested simulation algorithms are used to estimate the expectation of performance variables of interest. In the outer level of the algorithm (n) observations are generated for the parameters, and in the inner level (m) observations of the simulation model are generated with the value of parameters fixed at the value generated in the outer level. In this article, we consider the case in which the observations at both levels of the algorithm are independent, showing how the variance of the observations can be decomposed into the sum of a parametric variance and a stochastic variance. Next, we derive central limit theorems that allow us to compute asymptotic confidence intervals to assess the accuracy of the simulation-based estimators for the point forecast and the variance components. Under this framework, we derive analytical expressions for the point forecast and the variance components of a Bayesian model to forecast sporadic demand; and we use these expressions to illustrate the validity of our theoretical results by performing simulation experiments using this forecast model.

Abstract: This work is presenting a water level control and monitoring system in a tank, by using the development boards Arduino Uno, NodeMCU ESP8266 and the ultrasonic sensor HC-SR04. The water tank is supplied through a pump controlled by the development board Arduino Uno by means of a relay. The author has issued a control algorithm for controlling the water level and a program in the development environment Arduino IDE that has been implemented and validated on the experimental stand. For monitoring the development board NodeMCU ESP8266 has been used that takes the information from the ultrasonic sensor HC-SR04 and sends it through Wi-Fi to the platform ThingSpeak. Based on the experimental results it has been found out that the water level control system in the tank provides the performances imposed through the designing stage, and the pump running has been automatically stopped when the limit, settled through the program for the water maximum level in the tank, has been reached. The measured value of the water level is shown on the LCD 1602 display. In the water circuit of the home consumers or irrigation systems supplied from the tank a pump controlled by means of a mobile phone has been installed. In order to implement this control system, the author has issued a program for another development board Arduino Uno, whilst for the mobile phone he used the application Arduino Bluetooth Control. The advantage of this water level control and monitoring system in the tank is given by the very low costs in comparison to the cost of an industrial type control system.

Mangrove forests, which are essential for the maintenance of terrestrial and marine biodiversity on tropical coasts and constitute the main blue-carbon ecosystems for the mitigation of global warming, are among the world’s most threatened ecosystems. Mangrove conservation can greatly benefit from paleoecological and evolutionary studies, as past analogs documenting the responses of these ecosystems to environmental drivers such as climate change, sea level shifts and anthropogenic pressure. A database (CARMA) encompassing nearly all studies on mangroves from the Caribbean region, one of the main mangrove biodiversity hotspots, and their response to past environmental shifts has recently been assembled and analyzed. The dataset contains over 140 sites and ranges from the Late Cretaceous to the present. The Caribbean was the cradle of Neotropical mangroves, where they emerged in the Middle Eocene (~50 million years ago; Ma). A major evolutionary turnover occurred in the Eocene/Oligocene transition (34 Ma) that set the bases for the shaping of modern-like mangroves. However, the diversification of these communities leading to their extant composition did not occur until the Pliocene (~5 Ma). The Pleistocene (the last 2.6 Ma) glacial-interglacial cycles caused spatial and compositional reorganization with no further evolution. Human pressure on Caribbean mangroves increased in the Middle Holocene (~6000 years ago), when pre-Columbian societies began to clear these forests for cultivation. In recent decades, deforestation has significantly reduced Caribbean mangrove cover and it has been estimated that, if urgent and effective conservation actions are not undertaken, these 50 million-year-old ecosystems might disappear in a few centuries. A number of specific conservation and restoration applications based on the results of paleoecological and evolutionary studies are suggested.

Reliable and accurate flood prediction is a challenging task in poorly gauged basins due to data scarcity. Data is an essential component of any AI/ML model today, and the performance of such models hugely depends on the availability of sufficient amount of trusted, representative data. However, unlike a few well-studied rivers, most of the rivers in developing countries are still insufficiently monitored, which significantly hinges the design and development of advanced flood prediction models and early warning systems. This paper presents a multi-modal, sensor-based and near-real time river monitoring system to produce a multi-feature data set for the Kikuletwa river in Northern Tanzania, an area that heavily suffers from frequent floods. Our deployed system, which gather information about river depth levels and weather at several locations, aims at widening the ground truth of the river characteristics and eventually improve the accuracy of flood predictions. We provide details on the monitoring system used to gather the data as well as report on the methodology and the nature of the data. Finally, we present the relevance of the data set in the context of flood prediction, discussing the most suitable AI/ML-based forecasting approaches, while also highlighting some applications of the data set beyond flood warning systems.

Anemia is a significant public health problem among children, especially school-age children because their body quickly produces red blood cells to provide sufficient blood volume with plasma expansion to maintain blood concentration. This research aimed to study the anemia situation, knowledge about anemia, food consumption behaviors, and the association between knowledge, food consumption behaviors, and hematocrit level among school-age children in primary school, in Thasala district, Nakhon Si Thammarat Province. This is a descriptive study among 408 students, Grades 4 to 6, aged 9-12 years. Research instruments included the demographic data of the children and their knowledge about anemia, food consumption behaviors, and hematocrit assessment. Data were analyzed using descriptive, Spearman’s rank correlation coefficient, and logistic regression statistics. The results revealed that 23.2% of the samples had anemia, whereas 22.22% had mild anemia and 0.98% had moderate anemia. The children knew about anemia, where the mean score was at a moderate level (Mean= 6.63; SD= 2.51) out of 10. The mean score on food consumption behaviors was in the moderate level (Mean= 17.49; SD= 3.68) out of 24. There were significantly positive correlations between the knowledge about anemia and the hematocrit level at a moderate level (r= 0.45, p< 0.001). Correlation analysis revealed moderate food consumption behaviors with the hematocrit level (r= 0.40, p< 0.001). When confirm with Logistic regression found that knowledge about anemia (OR = 9.15, 95% CI: 4.57-18.34), and food consumption behaviors (OR = 19.09, 95% CI: 9.71-37.53) were significantly associated with the hematocrit level. Conclusions: This study showed that knowledge and appropriate food consumption behaviors are associated with hematocrit levels. Enhancing knowledge about anemia and food consumption behaviors may be reduced the prevalence of anemia in school-age children. The health care providers in primary care should be encouraged children to have health education and eat sufficient food.

Abstract The article discusses about the current situation of Novel Corona Virus also called as the COVID-19 that hinder for all human’s life including the education. Rapidly escalating COVID-19, has caused havoc in quality education and every educational institution are closed. As the UNESCO report it showed that 1.6 billion children being affected due to the close of institution across 191 countries. With the alternative method every education institution started blended learning virtual classes in order to continue learning environment in students. The articles investigate COVID-19 impact on student’s quality education in Nepal and social work implication. The findings of the study shows that the COVID-19 has seriously effects on the students learning environment. It showed the huge gap between getting the good education in Nepal. However, Nepal has also made some policies to provide equal quality education to all the children through the ICT and also encourage social work to actively participate on providing education to all the majority of group children in Nepal. Whereas social work applied the micro, messo, and macro level of implication in practice to provide the education for children in remote area of Nepal.

Yam (Dioscorea spp.) is a monocotyledonous herbaceous vine plant grown in the tropics and subtropics. It is a multi-species plant with varied intra- and interspecific ploidy levels. Of the 600 species, 11 are cultivated staple supporting the livelihood of over 300 million people. The paucity of information on ploidy and the genomic constitution is a significant challenge to the crop’s genetic improvement through crossbreeding. The objective of this study was to investigate the ploidy levels of 236 accessions across six cultivated and two wild species using chromosome counting, flow cytometry and genotyping-based ploidy determination methods. Results obtained from chromosome counting and genotyping-based ploidy determination were in agreement. In majority of the accessions, chromosome counting and flow cytometry were congruent, allowing future rapid screening of ploidy levels using flow cytometry. Among cultivated accessions, 168 (71%) were diploid, 50 (21%) were triploid, and 12 (5%) were tetraploid. Two wild species included in the study were diploids. Resolution of ploidy level in yams offers opportunities for implementing successful breeding programmes through intra- and inter-specific hybridization.

Investigation of sea-level positions during the highly-dynamic Marine Isotope Stage 3 (MIS 3: 29-61 kyrs BP) proves difficult because: i) in stable and subsiding areas, coeval coastal sediments are currently submerged at depths of few to several tens of meters below present sea level; ii) in uplifting areas, the preservation of geomorphic features and sedimentary records is limited due to the erosion occurred during the Last Glacial Maximum (LGM) with sea level at depth of -130 m, followed by marine transgression that determined the development of ravinement surfaces. This study discusses previous research in the Mediterranean and elsewhere, and describes new fossiliferous marine deposits laying on metamorphic bedrock of Cannitello (Calabria, Italy). Radiocarbon ages of marine shells (about 43 kyrs cal BP) indicate that these deposits, presently between 28 and 30 meters above sea level, formed during MIS 3.1. Elevation correction of the Cannitello outcrops (considered in an intermediate-to-far-field position with respect to the ice sheet) with the local vertical tectonic rate and Glacial Isostatic Adjustment (GIA) rate allows to propose a revision of the eustatic depth for this highstand. Our results are consistent with recently proposed estimates based on a novel ice sheet modelling technique.

In a safety-critical system typically not all provided services have the same criticality, which we call mixed-criticality systems. Criticality arithmetic, also called SIL arithmetic, is an approach to lower the development effort of a service by providing redundancy with tasks that are developed for a lower criticality level. In this paper we present ATMP-CA, which is a derivation of the multi-core scheduler ATMP. ATMP-CA is able to take into account the knowledge about the use of criticality arithmetic. ATMP-CA has a modified core allocation and procedure for utility optimisation, considering the context of the replicated tasks. We conducted experiments that show that ATMP-CA is able to provide the services using criticality arithmetic, while the reference schedulers were not.

Evolutionary convergence provides natural opportunities to investigate how, when, and why novel traits evolve. Many convergent traits are complex, highlighting the importance of explicitly considering convergence at different levels of biological organization, or ‘multi‐level convergent evolution’. To investigate multi‐level convergent evolution, we propose a holistic and hierarchical framework that emphasizes breaking down traits into several functional modules. We begin by identifying long‐standing questions on the origins of complexity and the diverse evolutionary processes underlying phenotypic convergence to discuss how they can be addressed by examining convergent systems. We argue that bioluminescence, a complex trait that evolved dozens of times through either novel mechanisms or conserved toolkits, is particularly well suited for these studies. We present an updated estimate of at least 94 independent origins of bioluminescence across the tree of life, which we calculated by reviewing and summarizing all estimates of independent origins. Then, we use our framework to review the biology, chemistry, and evolution of bioluminescence, and for each biological level identify questions that arise from our systematic review. We focus on luminous organisms that use the shared luciferin substrates coelenterazine or vargulin to produce light because these organisms convergently evolved bioluminescent proteins that use the same luciferins to produce bioluminescence. Evolutionary convergence does not necessarily extend across biological levels, as exemplified by cases of conservation and disparity in biological functions, organs, cells, and molecules associated with bioluminescence systems. Investigating differences across bioluminescent organisms will address fundamental questions on predictability and contingency in convergent evolution. Lastly, we highlight unexplored areas of bioluminescence research and advances in sequencing and chemical techniques useful for developing bioluminescence as a model system for studying multi‐level convergent evolution.

This article presents a new method of segmenting images with gray levels. The method is based on determining several thresholds for separation of gray levels. The determination of these thresholds is done using the certainty of the neutrosophic information. The concept of this method can be stated simply: to choose the local maximums for the neutrosophic certainty.

The humpback puffer, Tetraodon palembangensis, also known as Pao palembangensis, is a species of poisonous freshwater pufferfish mainly distributed in Southeast Asia (Thailand, Laos, Malaysia and Indonesia). Despite interesting biological features, such as its very inactive nature, tetrodotoxin production and body expansion mechanisms, molecular research on the humpback puffer is still rare because of the lack of a high-quality reference genome. Here, we reported a first chromosome-level genome assembly of an adult humpback puffer, of which the genome size is 362 Mb with ~1.78 Mb contig N50 and ~15.8 Mb scaffold N50s. Based on the genome, ~61.5Mb (18.11%) repeat sequences were also identified, and totally 19,925 genes were annotated, 99.20% of which could be predicted with function using protein-coding function databases. Finally, a phylogenetic tree was constructed with single-copy gene families from ten teleost fishes. The humpback puffer genome will be a valuable genomic resource to illustrate possible mechanisms of tetrodotoxin synthesis and tolerance, providing clues for future detailed studies of biological toxins.

Recent climatic changes have resulted in an increased frequency and prolonged periods of drought and strained water resources affecting plant production. We explored the possibility of reducing irrigation in a container nursery and studied the growth response of seedlings of economically important forest trees: broadleaf deciduous angiosperms Fagus sylvatica, Quercus petraea and evergreen conifers Abies alba and Pinus sylvestris. We also studied markers of water stress including modifications of biomass allocation, leaf anatomy, proline accumulation and expression of selected genes. Growth of the broadleaved deciduous species was more sensitive to the reduced water supply than that of conifers. Remarkably, growth of the shade tolerant Abies was not affected. Adjustment of biomass allocations was strongest in P. sylvestris, with a remarkable increase in allocation to roots. In response to water deficit both deciduous species accumulated proline in leaves and produced leaves with shorter palisade cells, reduced vascular tissues and smaller conduit diameters, but not conifers. Relative transcript abundance of a gene encoding a Zn-finger protein in Q. petraea and a gene encoding a pore calcium channel protein 1 in A. alba increased as water deficit increased. These findings suggest that in container nursery, the genetic selection can be initiated by water deficit. Our study shows major differences between functional groups in response to irrigation, with seedlings of evergreen conifers having higher tolerance than the deciduous species. This suggests that major water savings could be achieved by adjusting irrigation regime to functional group or species requirements.

Multiple studies have shown that hospital settings are poorly cleaned during terminal cleaning. The adequacy of these cleaning methods has been undermined by presence of multi drug resistant bacteria on hospital surfaces. This case is even more serious in developing countries leading to health care- associated infections that pose a great threat to patients, visitors and health care providers in hospital settings.This study used various microbiological techniques to test for antibiotic susceptibility profiles of bacteria present at Thika Level 5 Hospital surfaces, Kenya. A simple random cross sectional study was performed, with a total of 85 samples being collected from five different sites. The sites included male and female wards, health care personnel offices, latrine, and kitchen surfaces. Samples were collected using sterile swabs, dipped in normal saline, and transported to the laboratory within 2Hours for processing.Of the 85 plates cultured, 47 plates showed bacterial growth (55%) on selective media with a significant P value of 0.0357. Seven different species of bacteria were identified biochemically from all sites, Escherichia coli was the most abundant species (28%), and the least was Salmonella typhii (5%). Multiple drug resistance was common in the different bacteria identified. All isolates were resistant to chloramphenical and susceptible to gentamycin. The most resistant microorganism was Staphylococcus aureus (50%), and the least resistant microorganism was Klebsiella pneumoniae (12.5%). The antimicrobial resistant bacterial species identified in this study have been documented to cause serious health care associated infections. These results present a significant public health concern because there is a possibility of patients, staff and visitors contacting nosocomial infections when they come into contact with surfaces at Thika Level 5 Hospital surfaces, Kenya.

Background: Acute appendicitis (AA) is the most common cause of emergency surgery. Perforation is more common than adults. Early diagnosis and new markers are needed. The aim of this study was to investigate the effects of plasma Fetuin-A (FA) levels in patients with the acute abdomen (AB). Material and Method: This prospective study included 107 patients younger than 16 years of age who were admitted to the emergency department for abdominal pain between January 2018 and December 2018. The patients who presented to abdominal pain were divided into two groups as AA and other causes (OC) of AB. T Patients with acute appendicitis; intraperitoneal, retrocolic / retrocecal and appendicitis were divided into three groups. Also, the AA group was divided into two groups as perforated appendicitis and non-perforated appendicitis. Serum FA levels of the patients were evaluated in the emergency department. Results: In the AA group, C-reactive protein (CRP) and white blood cell (WBC) levels were higher, and FA levels were significantly lower than in the AB group. Intraperitoneal localization was 95.2% and perforation was frequent. When significant values in the univariate regression analysis for acute abdomen and perforation were compared in the multivariate regression analysis, CRP, WBC, and FA levels were found to be prognostic. Also, decreased FA levels were associated with AA while too much decreased FA levels were associated with the risk of perforation. Conclusion: While trying to diagnose AA in children, the FA level, CRP and WBC may be predictive values to identify risk factors.

There has been rampant fold-ups, merger and acquisitions occurring in the Ghanaian banking industry. Then, the questions arise: Is the Ghanaian Financial System in Crisis? This study was conducted to find answers to these problems unsolved with prior literature. A sample of seventy customers of the Royal Bank, 8 employees of the Royal Bank and 2 managers of the Royal Bank were selected for a case-survey. The study also monitored the Trend of the Ghanaian Financial System through the reading and monitoring of daily news on the Financial System and reports of banks. The data from the field and the secondary data from news and reports were analysed symmetrically. The study drew on Minsky’s Financial Crisis Theory to explain the phenomenon in the Ghanaian economy and to draw predictions of what would happen in other developing economies. The study found out that: (1) The Ghanaian financial system is fragile and it holds true for most developing economies; (2) The financial system suffers greatly when the confidence level of customers falls significantly; (3) Management information systems raises the confidence level of customers (borrowers and lenders) such that there is a greater fall and impact in times of instability in the economy; (4) The higher the level of MIS adoption in an unstable economy, the more fragile the Financial System becomes and (5) A higher adoption of Management Information Systems in a Fragile Financial System indirectly contributes to Financial Crisis of the Financial System.

Study nature of epidemiological risk factors and patterns of distribution of mortality from Alzheimer's (D_A) in 160 countries. An exponential Malthus model was used to construct adequate approximations of statistical data. Proportionality of average lifetime after 55 years (Δt) to education index (Ψ) was established. Ranking of countries by increasing value of ΨΔt showed that D_A depends exponentially on ΨΔt and all countries can be divided into three groups in accordance with level of their economic development. In series of countries of low, medium and highly developed, their average values of D_A increase exponentially. Growth of D_A in developed countries in post-industrial epoch was explained by emergence of a new risk factor Alzheimer's of a mental nature. A mismatch of complexity or, on contrary, primitiveness of profession with level of mental development of worker, provokes development of chronic stress in him, fraught with pathologies of cognitive function metabolism in elderly. The geography of Alzheimer's disease was explained by the dependence of the human mentality on latitudinal climate change and on the chiral factor of a solar nature acting at night on a sleeping person.

On 5-7 April 2018 a landfalling atmospheric river resulted in widespread heavy precipitation in the Sierra Nevada of California and Nevada. Observed snow levels during this event were among the highest snow levels recorded since observations began in 2002 and exceeded 2.75 km for 31 hours in the northern Sierra Nevada and 3.75 km for 12 hours in the southern Sierra Nevada. The anomalously high snow levels and over 80 mm of precipitation caused flooding, debris flows, and wet snow avalanches in the upper elevations of the Sierra Nevada. The origin of this atmospheric river was super typhoon Jelawat, whose moisture remnants were entrained and maintained by an extratropical cyclone in the northeast Pacific. This event was notable due to its April occurrence, as six other typhoon remnants that caused heavy precipitation with high snow levels (mean = 2.92 km) in the northern Sierra Nevada all occurred during October.

Coastal inundation is an increasing problem. Sea-level rise will greatly increase the frequency and depth of inundation, forcing vulnerable communities to adapt. Communities will need to decide when and how to adapt. The process of decision-making along adaptive pathways is now being used internationally to plan for adaptation over time by anticipating decision points in the future however it unfolds. This process requires risk and uncertainty considerations to be transparent in the scenarios used in such planning. We outline a framework for uncertainty identification and management within coastal hazard assessments which recognizes different types of decision and identifies the types of uncertainty that must be accounted for, such as statistical, scenario and deep uncertainty types. We show how coastal-inundation hazard can be mapped and presented in a way that clearly separates sources of uncertainty, so that they are transparent within a dynamic adaptive pathways planning process. Traditional coastal inundation maps show inundated area only. We present maps of inundation depth and frequency which clearly show the degree of exposure, where that exposure occurs, and how much sea-level rise can be tolerated. The new uncertainty framework and mapping techniques can better identify decision points and their expected time range, which provides more useful input to the adaptation process than traditional coastal inundation assessments.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

The severe and complex COVID-19 symptoms, often needing hospital care, occur suddenly, late in the virus replication stage of SARS-CoV-2 infection. Hospitalised patients have tissue damage due to micro-clots at multiple sites. Could long-covid, also clinically variable, be a milder form caused by “nano-clots”, too small to cause detectable tissue damage? The timing and suddenness of the onset of serious disease needs an explanation. A paper reported on the first 20 children needing urgent hospital care. No child had any symptoms prior to suddenly becoming seriously ill, only one had a positive PCR test but all had positive SARS-CoV-2 antibody test. That finding indicated to me that this onset occurred at the moment of sero-conversion. An emerging viral moiety, the virion-IgG-antibody complex, has concentrations rapidly increasing, then decreasing. It is known that influenza-IgG-antibody-complex consists of many virions bound together by the antibody. It seems a reasonable step to propose that SARS-2, being a large virus and having many spike proteins, can form larger clumps of virus-IgG-antibody complexes than with influenza, the former being sufficiently large to initiate micro-clots. Therefore, my hypotheses is that the SARS-CoV-2 virion-antibody complex initiates micro-clot formation. Either before or after sero-conversion, the complex will be at too low a concentration to initiate micro-clots. To be useful, a hypothesis should be testable, provide explanations and give predictions. My presentation will give examples. I like the way that several apparently separate pieces of a jig-saw puzzle have come together to form a single picture. [I suggest that the reader scrolls down to the addenda [10,11 & 12] before reading the ICAR Poster]

The spatial segregation is a characteristic of Latin American cities, resulting in distinct dynamics of social inclusion and exclusion at both spatial and identity levels. Then, specific green spaces may convert into appreciated and contested territories, where various actors negotiate their uses and regulations. Considering a case-study in a green icon of the metropolitan city of Santiago de Chile, the main objective of the present study was to describe and comprehend the uses and meanings of the Quebrada Macul park among different social groups over the past two decades. We employed qualitative methods including six in-depth interviews with key informants (social and ecological leaders, historical neighbors, and park workers), five participant observations in the park, and statistical analysis of visitors. Results reveal that (1) the transition of being a popularly used hill to a metropolitan park rises tensions between public and private statuses of place; (2) conflicts emerge regarding who uses the space and how, reflecting power dynamics among different social groups; (3) the park, beyond being a public space, holds significant identity value for its historical residents, both for those who fought for its recovery and those who have lived closely, so processes of forgetfulness might be resentful. We conclude on enduring meanings of the park associated with the struggle for the place among different groups, highlighting the role of memory for the social integration of groups among natural spaces.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

Micro-plastics (MPs) become significantly important to society since their commercial manufacture began in the 1950s because of their low production costs, stability, light weight, and adaptability. Plastic was produced in 400 million tons worldwide in 2020, compared to 1.5 million tons just 60 years earlier. Scientists predict that by 2050, plastic production would increase to 33 billion tons. MPs are a rising scientific and societal issue in the environment as a new type of contaminant that is widely disseminated in aquatic ecosystems and organisms. Aquatic species that come into contact with MPs for an extended period of time experience ecotoxicity, which includes oxidative stress, genotoxicity, neurotoxicity, and reproductive issues. In aquatic environments, MPs not only transport chemicals within animals but also serve as mediators for chemicals or other contaminants. As a result of co-exposure of MPs and chemical contaminants, various toxicity incidences involving aquatic organisms have been reported. The final exposure of MPs occurs in humans through biomagnification of aquatic edible products. This study presents an important overview of the literature on MP ingestion by aquatic biota. It covers topics such as the present scenario of plastic pollution worldwide, the pathways that MPs take to reach humans and aquatic species, the eco-toxicological impacts of MPs on aquatic species, the relation between MPs and other environmental pollution and the ensuing effects on aquatic organisms, and the MP pollution status in Bangladesh.

Castanea sativa Mill., an indigenous species of the mountainous Gabala region of Azerbaijan, where its local variety is now facing the danger of extinction. The preservation of this variety of European chestnut requires the development of effective strategies for reliable in vitro regeneration systems as an alternative to traditional methods, which has become the main objective of this study. In solving this problem, the generally accepted technique of micro-multiplication of axillary shoots was mainly used. First, a phased sterilization of was carried out using liquid soap, Previkur fungicide and mercury (II) chloride. DKW (Driver and Kuniyuki Walnut) nutrient medium was used for germination of explants, into which growth stimulants BAP (Benzilamunapurine), IBA (Indole - 3 butyric acid), IAA (Indole Acetic acid), NAA (Naphthalene Acetic Acid) and GA3 (Gibberelic acid) were introduced in various combinations and quantities. The test of the above-mentioned sterilization model revealed significant shortcomings in terms of the acceptability of the results obtained (16-77%). It was also found that the germination of explants takes 14 days and it is better to conduct it in a DKW environment containing hormones BAP (0.6 mg), IBA (0.1 mg) and GA3 (0.1 mg) / 1 L DKW. A mixture of BAP (0.1mg) + IBA (0.35 mg) is more suitable for the reproduction of grown explants + GA3 (0.2 mg) / 1 l DKW (the result is 3 new micro-plants for each explant), and for good root formation (it takes 30 days) – a mixture of IBA 1.0 mg + NAA 0.5 mg + IAA 0.5 mg / l L DKW. After the shoots have acquired a certain length (at least 1.5 cm), it is required to transfer them for 22 days to a DKW medium containing IBA (1 mg), IAA (0.5 mg) and NAA(0.5 mg) / l L DKW so that the root splitting process begins and ends.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Artificial intelligence, a key technological tool in the era of the 4th Industrial Revolution, is being actively applied to education beyond industry, economy, and culture. In the future society, understanding and using artificial intelligence technology will be considered an essential skill for everyone, and the professionalism of AI education for pre-service teachers nurturing future talents is also important. This study verifies the effectiveness of pre-service teachers after undergoing a 15-week extension program consisting of AI Literacy Education (10 weeks), AI-Linked Subjet Education (3 weeks), and Micro-teaching (2 weeks) which was designed to enhance the AI ​​education professionalism of pre-service teachers. The AI Literacy Education section consisted of understanding AI, AI ethics, and basic programming, and the education was conducted through both experience and practice. After that, the pre-service teachers analyzed the curriculum of the 5th and 6th grades of an elementary school, and developed a subject-related education program using AI tools in three stages. Using the developed program, micro-teaching classes were conducted twice. The study results are as follows. First, there was a change in the positive perception of AI (p<.05). Second, the understanding of AI educational technology tools was improved and the recognition of the usefulness of developing a curriculum-related program was expanded. Third, the importance of teacher competency development was learned through the micro-teaching, and the students' understanding of the learning process was expanded.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.