Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Nitrogen and phosphorous support the ecosystem by supplying nutrients to algae and aquatic plants. Having them in excess results in the eutrophication of waters creating quality problems. In the past, nitrogen has been widely investigated for wells in the context of groundwater flow. However, a national-scale nitrogen assessment in rivers and streams has not received enough attention. In this research, the Wilcoxon rank sum test, as a non-parametric hypothesis testing method, has been applied to nitrogen concentration in the form of nitrate-nitrogen and nitrite-nitrogen in rivers and streams of the Contiguous United States. This approach was particularly selected because of the non-normal and positively skewed nitrogen levels occurring in the surface flow. This method was able to identify the impaired body of waters as well as quantify the confidence, significance, and errors involved. The Northern Appalachians (NAP), Northern Plains (NPL), and Xeric (XER) ecoregions were worsening in the nitrogen-nitrate condition with NAP, and XER needed immediate actions. The nitrite-nitrogen condition did not pose an immediate threat, so mitigation plans should focus more on nitrate-nitrogen remediation. It was shown that the method was superior to the two-sample t-test by yielding lower type II errors.

Ayurveda as a healthcare system has survived for thousands of years but continues to be dogged by reported lack of efficacy of the treatments in clinical trials. The reported lack of efficacy could be due to a real lack of efficacy (which then contradicts the survival of Ayurveda as a functional medical system enjoying considerable public patronage) or could be attributed to inadequacies in the efforts towards evidence generation or in a larger context the overall scientific conduct of research in Ayurveda. In an effort towards better evidence generation, there is an immediate need for standardizing the design, conduct and reporting of clinical trials of Ayurveda but it is a daunting task. For this effort to benefit the scientific endeavors of Ayurveda researchers, it should allow the researchers to be able to apply Ayurveda’s multi-component, individualized and inherently holistic approach. Statistical principles can benefit this effort. Statistical hypothesis testing (SHT) is central to these statistical principles and also aligns well with conventional scientific principles of evidence generation. Although there are challenges with SHT, good practitioners engaged in it do much more than just apply the mathematical theory behind it. As a particular example, lot of time in clinical trial designing is spent in addressing biases and designing trials prudently by minimizing the effect of such biases. SHT can benefit such an effort objectively. There is a need for Ayurveda researchers to engage deeply and mindfully about biases in study design in order to gain scientific validity and acceptability. The article highlights issues that arise in Ayurveda research, and discusses few ways of dealing with these issues using statistical principles.

The performance of a normal-strength SHCC under impact loading was studied using the results obtained from a split Hopkinson tension bar (SHTB). The focus of the investigation is to explain the mechanisms behind the peculiar rate-dependent behavior of SHCC under tensile loading. With the help of frames obtained by high-speed cameras and the subsequent Digital Image Correlation (DIC) analysis, the stress-strain relation of the SHCC obtained in SHTB was analyzed. The investigation of the composite’s behavior was supported by constituent-level experiments on the non-reinforced matrix of the SHCC and on the fiber-matrix bond. In the case of the constituent matrix, the well-known apparent increase in the tensile strength of the cement-based matrix and its influence on the behavior of SHCC was studied. For this purpose, experiments on the SHCC specimens with different geometries were performed in the SHTB. The results obtained from these experiments and those obtained by DIC show that commonly used analytical models, in which the specimen is assumed elastic, cannot capture the effects of structural inertia on the results. Thus, an alternative novel method based on the results of DIC has been used to explain and quantify the contribution of structural inertia. The rate-dependent behavior of the fiber-matrix bond was studied by performing high-speed single fiber pullout tests in a miniaturized split Hopkinson tension bar. This novel experimental technique enabled explanation of the rate-dependent bridging action of the fibers in SHCC. Based on the results, the enhanced behavior of SHCC under impact loading is explained.

Background: HIV poses a threat to global health. With effective treatment options available, education and testing strategies are essential in preventing transmission. Text messaging is an effective tool for health promotion and can be used to target higher risk populations. This study reports on the design, delivery and testing of a mobile text messaging SMS intervention for HIV prevention and awareness, aimed at adults in the construction industry and delivered during the COVID-19 pandemic. Method: Participants were recruited at Test@Work workplace health promotion events (21 sites, n=464 employees), including health checks with HIV testing. Message development was based on a participatory design and included a focus group (n=9) and message fidelity testing (n=291) with assessment of intervention uptake, reach, acceptability, and engagement. Barriers to HIV testing were identified and mapped to the COM-B behavioural model. 23 one-way push SMS messages (19 included short web links) were generated and fidelity tested, then sent via automated SMS to two employee cohorts over a 10-week period during the COVID-19 pandemic. Engagement metrics measured were; opt-outs, SMS delivered/read, number of clicks per web link, and four two-way pull messages exploring repeat HIV testing, learning new information, perceived usefulness and behaviour change. Results: 291 people participated (68.3% of eligible attendees). A total of 7,726 messages were sent between March and June 2020, with 91.6% successfully delivered (100% read). 12.4% of participants opted out over 10 weeks. Of delivered messages, links were clicked an average of 14.4%, max 24.1% for HIV related links. The number of clicks on web links declined over time (r= -6.24, p=0.01). Response rate for two-way pull messages was 13.7% of participants. Since the workplace HIV test offer at recruitment, 21.6% reported having taken a further HIV test. Qualitative replies indicated behavioural influence of messaging on exercise, lifestyle behaviours and intention to HIV test. Conclusion: SMS messaging for HIV prevention and awareness is acceptable to adults in the construction industry, has high uptake, low attrition and good engagement with message content, when delivered during a global pandemic. Data collection methods may need refinement for audience and effect of COVID-19 on results is yet to be understood.

In a wide range of lymphoid neoplasms, the process of malignant transformation is associated to somatic mutations in B cells that affect the epigenetic machinery. Consequential alterations in histone modifications contribute to disease-specific changes in the transcriptional program. Affected genes commonly play important roles in cell cycle regulation, apoptosis-inducing signal transduction and DNA damage response, thus facilitating the emergence of malignant traits that impair immune surveillance and favor the emergence of different B-cell lymphoma subtypes. In the last two decades, the field has made a major effort to develop therapies that target these epigenetic alterations. In this review, we discuss which epigenetic alterations occur in non-Hodgkin B-cell lymphoma. Furthermore, we aim to present in close to comprehensive manner the current state-of-the-art in the preclinical and clinical development of epigenetic drugs. We focus on therapeutic strategies interfering with histone methylation and acetylation as these are most advanced in being deployed from the bench-to-bedside and have greatest potential to improve the prognosis of lymphoma patients.

Background: The epidemiological situation generated by COVID-19 has cast into sharp relief the delicate balance between public health priorities and the economy, with businesses obliged to toe a line between employee health and continued production. In an effort to detect as many cases as possible, isolate contacts, cut transmission chains and limit the spread of the virus in the workplace, mass testing strategies have been implemented in both public health and industrial contexts to minimize the risk of disruption in activity. Objective: To evaluate the economic impact of mass workplace testing strategy as carried out by a large automotive company in Catalonia in terms of health and healthcare resource savings. Methodology: Analysis of health costs and impacts based on the estimation of mortality and morbidity avoided because of screening and the resulting savings in healthcare costs. Results: The economic impact of the mass workplace testing strategies (using both PCR and RAT tests) was approximately €10.44 per test performed or €5,575.49 per positive detected. 38% of this figure corresponds to savings derived from better use of health resources (hospital beds, ICU beds and follow-up of infected cases), while the remaining 62% corresponds to improved health rates due to avoided morbidity and mortality. In scenarios with higher positivity rates and a greater impact of the infection on health and the use of health resources, these results could be up to ten times higher (€130.24 per test performed or €69,565.59 per positive detected). Conclusion: In the context of COVID-19, preventive actions carried out by the private sector to safeguard industrial production also have concomitant public benefits in the form of savings in healthcare costs. Thus, governmental bodies need to recognize the value of implementing such strategies in private settings and facilitate them through, for example, subsidies.

An iterative outlier elimination procedure based on hypothesis testing, commonly known as Iterative Data Snooping (IDS) among geodesists, is often used for the quality control of the modern measurement systems in geodesy and surveying. The test statistic associated with IDS is the extreme normalised least-squares residual. It is well-known in the literature that critical values (quantile values) of such a test statistic cannot be derived from well-known test distributions, but must be computed numerically by means of Monte Carlo. This paper provides the first results about Monte Carlo-based critical value inserted to different scenarios of correlation between the outlier statistics. From the Monte Carlo evaluation, we compute the probabilities of correct identification, missed detection, wrong exclusion, overidentifications and statistical overlap associated with IDS in the presence of a single outlier. Based on such probability levels we obtain the Minimal Detectable Bias (MDB) and Minimal Identifiable Bias (MIB) for the case where IDS is in play. MDB and MIB are sensitivity indicators for outlier detection and identification, respectively. The results show that there are circumstances that the larger the Type I decision error (smaller critical value), the higher the rates of outlier detection, but the lower the rates of outlier identification. For that case, the larger the Type I Error, the larger the ratio between MIB and MDB. We also highlight that an outlier becomes identifiable when the contribution of the measures to the wrong exclusion rate decline simultaneously. In that case, we verify that the effect of the correlation between the outlier statistics on the wrong exclusion rates becomes insignificant from a certain outlier magnitude, which increases the probability of identification.

Duchenne muscular dystrophy (DMD) is a fatal X-linked recessive neuromuscular disorder most commonly caused by mutations disrupting the reading frame of the dystrophin (DMD) gene. DMD codes for dystrophin, which is critical for maintaining the integrity of muscle cell membranes. Without dystrophin, muscle cells receive heightened mechanical stress, becoming more susceptible to damage. An active body of research continues to explore therapeutic treatments for DMD as well as to further our understanding of the disease. These efforts rely on having reliable animal models that accurately recapitulate disease presentation in humans. While current animal models of DMD have served this purpose quite well, each comes with their own limitations. To help overcome this, clustered regularly interspaced short palindromic repeats (CRISPR)-based technology has been extremely useful in creating novel animal models for DMD. This review focuses on animal models developed for DMD that have been created using CRISPR, their advantages and disadvantages as well as their applications in the DMD field.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

The Sei Dareh Bridge is a cable-stayed bridge located in West Sumatra Province, Indonesia. The bridge, has a main span of 123 meters length and 9 meters wide, crosses the Batanghari River. Traffic load is transmitted through 4 prestressed cables to a 42.4 meter high pylon made of concrete. Bridge deck and traffic loads are directly supported by steel box girders as main beams that are reinforced laterally with cross beams IWF 800.300.16.24 and stringers IWF 350.350.12.19. This paper discusses static and dynamic testing on the bridge which aims to assess the feasibility before it is opened for public. Based on the test, it was concluded that the 73% static load could not be achieved because the deflection that occurred was beyond the allowable deflection. This is exacerbated by the sound of a loud clanging sound on the ST2-X1 prestressed cable when loading to 240 tons or 58% of the targeted load. In addition, this bridge is included in the "lazy bridge" category because it takes 24 hours to return to an undeformed condition after loading. As a recommendation for this bridge, it is necessary to carry out a structural health monitoring system (SHMS) regularly on the vehicle floor and cables.

Most of the research of mental fatigue evaluation mainly concentrated on some indexes that require sophisticate and large instruments which make the detection of mental fatigue cumbersome, time-consuming, and difficult to apply on a large scale. A quick and sensitive mental fatigue detection index is necessary so that mental workers can be alerted in time and take corresponding countermeasures. But to date, no studies have compared the sensitivity of common objective evaluation indexes. To solve these problems this study recruited 56 human subjects. These subjects were evaluated using six fatigue indexes: the Stanford sleepiness scale, digital span, digital decoding, short-term memory, critical flicker fusion frequency (CFF), and speed perception deviation. The results of fatigue tests before and after mental fatigue were compared, and a one-way analysis of variance (ANOVA) was performed on the speed perception deviation. The result indicated the significance of this index. Considering individual differences, the relative fatigue index (RFI) was proposed to compare the sensitivity of the indexes. The results showed that when the self-rated fatigue grade changed from non-fatigue to mild fatigue, the ranges of RFI values for digital span, digital decoding, short-term memory and CFF were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. Correspondingly, when the self-rated fatigue grade changed from non-fatigue to severe fatigue, the ranges of RFI values for the above indexes were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. These results suggest that the sensitivity of the digital decoding, digital span, short-term memory, and CFF decreased sequentially when the self-evaluated fatigue grade changed from no fatigue to mild or severe fatigue. The RFI individuality of the speed perception deviation is highly variable and is not suitable as an evaluation index. In mental fatigue testing, digital decoding testing can provide faster, more convenient, and more accurate results.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

Regional mechanics of the heart is vital in the development of accurate computational models for the pursuit of relevant therapies. Challenges related to heart dysfunctioning are the most important sources of mortality in the world. For example, myocardial infarction (MI) is the foremost killer in sub-Saharan African countries. Mechanical characterisation plays an important role in achieving accurate material behaviour. Material behaviour and constitutive modelling are essential for accurate development of computational models. In most cases previously, the mechanical properties of the heart myocardium were assumed to be homogeneous. The main objective of this paper is to determine the mechanical material properties of healthy porcine myocardium in three regions, namely left ventricle (LV), mid-wall/interventricular septum (MDW) and right ventricle (RV). The biomechanical properties of the pig heart RV, LV and MDW were characterised using biaxial testing. The biaxial tests show the pig heart myocardium behaves non-linearly, heterogeneously and anisotropically. In this study, it was shown that RV, LV and MDW may exhibit slightly different mechanical properties. Data presented here may be helpful in regional tissue mechanics, especially for the understanding of various heart diseases and development of new therapies.

Dry powder inhalers are used by a large number of patients worldwide to treat respiratory diseases. The objective of this work is to experimentally investigate changes in aerosol particle diameter and particle number concentration of pharmaceutical aerosols generated by five dry powder inhalers under realistic inhalation and exhalation conditions. The active respiratory system model (xPULM™) was used as a model of the human respiratory system and to simulate a patient undergoing inhalation therapy. A mechanical upper airway model was developed, manufactured and introduced as a part of the xPULM™ to represent the human upper respiratory tract with high fidelity. Integration of optical aerosol spectrometry technique into the setup allowed for evaluation of pharmaceutical aerosols. The results show that the upper airway model increases the resistance of the overall system and act as a filter for bigger particles (>3 µm). Furthermore, there is a significant difference (p < 0.05) in mean particle diameter between inhaled and exhaled particles with the majority of the particles depositing in the lung. The minimum deposition is reached for particle size of 0.5 µm. The mean particle number concentrations exhaled are 2.94% (BreezHaler®), 2.66% (Diskus®), 10.24% (Ellipta®) 2.13% (HandiHaler®) and 6.22% (Turbohaler®). In conclusion, the xPULM™ active respiratory system model is a viable option for studying interactions of pharmaceutical aerosols and the respiratory tract in terms of applicable deposition mechanisms. The model can support the reduction of animal experimentation in aerosol research and provide an alternative to experiments with human subjects.

Model-based image reconstruction has brought improvements in terms of contrast and spatial resolution to imaging applications such as magnetic resonance imaging and emission computed tomography. However, their use for pulse-echo techniques like ultrasound imaging is limited by the fact that model-based algorithms assume a finite grid of possible locations of scatterers in a medium -- which does not reflect the continuous nature of real world objects and creates a problem known as off-grid deviation. To cope with this problem, we present a method of dictionary expansion and constrained reconstruction that approximates the continuous manifold of all possible scatterer locations within a region of interest. The expanded dictionary is created using a highly coherent sampling of the region of interest, followed by a rank reduction procedure based on a truncated singular value decomposition. We develop a greedy algorithm, based on the Orthogonal Matching Pursuit (OMP), that uses a correlation-based non-convex constraint set that allows for the division of the region of interest into cells of any size. To evaluate the performance of the method, we present results of 2-dimensional ultrasound image reconstructions with simulated data in a nondestructive testing application. Our method succeeds in the reconstructions of sparse images from noisy measurements, providing higher accuracy than previous approaches based on regular discrete models.

In addition to the traditional QoS metrics of delay, delay jitter, and packet loss probability (PLP), Quality of Experience (QoE) is now widely accepted as a numerical proxy for actual user experience. The literature has reported many mathematical mappings between QoE and QoS. These QoS parameters are measured by the network providers using sampling. There are some papers studying sampling errors in QoS measurements; however there is no account of propagation of these sampling errors to QoE evaluation. In this paper, we used industrially acquired measurements of PLP and jitter to evaluate the sampling errors and correlation in measurements. Focussing on Video-on-demand (VoD) applications, we use subjective testing and regression to map QoE metrics onto PLP and jitter. The resulting mathematical functions of QoE and theory of error propagation was used to evaluate the propagated error in QoE, and this error was represented as confidence interval. Using the guidelines of UK government for sampling, our results indicate that confidence intervals around estimated QoE in a busy hour can be between MOS=1 to MOS=5 at targeted operating point of QoS parameters. These results are a new perspective on QoE evaluation, and are of great significance to all organisations that need to estimate the QoE VoD applications precisely.

The determination of crack propagation velocities can provide valuable information for a better understanding of damage processes of concrete. The spatio-temporal analysis of crack patterns developing at a speed of several hundred meters per second is a rather challenging task. In the paper, a photogrammetric procedure for the determination of crack propagation velocities in concrete specimens using high-speed camera image sequences is presented. A cascaded image sequence processing which starts with the computation of displacement vector fields for a dense pattern of points on the specimen’s surface between consecutive time steps of the image sequence chain has been developed. These surface points are triangulated into a mesh, and as representations of cracks, discontinuities in the displacement vector fields are found by a deformation analysis applied to all triangles of the mesh. Connected components of the deformed triangles are computed using region-growing techniques. Then, the crack tips are determined using principal component analysis. The tips are tracked in the image sequence and the velocities between the time stamps of the images are derived. A major advantage of this method as compared to established techniques is in the fact of its allowing for spatio-temporally resolved, full-field measurements rather than point-wise measurements and that information on crack width can be obtained simultaneously. To validate the experimentation, the authors processed image sequences of tests on four compact-tension specimens performed on a split-Hopkinson tension bar. The images were taken by a high-speed camera at a frame rate of 160,000 images per second. By applying to these datasets the image sequence processing procedure as developed, crack propagation velocities of about 800 m/s were determined with a precision in the order of 50 m/s.

Current oncological developments are based on improved understanding of genetics, and especially the discovery of genes whose alterations affect cell functions with consequences for the whole body. Our work is focused on the one of these genes, the BARD1 and its oncogenic role in breast cancer. Most importantly, the study points to new avenues in the treatment and prevention of the most frequent female cancer based on BARD1 research. The BARD1 and BRCA1 proteins have similar structures and functions, and they combine to form the new molecule BARD1-BRCA1 heterodimer. The BARD1-BRCA1 complex is involved in genetic stabilization at the cellular level. It allows to mark abnormal DNA fragments by attaching ubiquitin to them. In addition, it blocks (by ubiquitination of RNA polymerase II) the transcription of damaged DNA. Ubiquitination, as well as stabilizing chromatin, or regulating the number of centrosomes, confirms the protective cooperation of BARD1 and BRCA1 in the stabilization of the genome. The overexpression of the oncogenic isoforms BARD1β and BARD1δ permit cancer development. The introduction of routine tests, for instance, to identify the presence of the BARD1β isoform, would make it possible to detect patients at high risk of developing cancer. On the other hand, introducing BARD1δ isoform blocking therapy, which would reduce estrogen sensitivity, may be a new line of cancer therapy with potential to modulate responses to existing treatments. It is possible that the BARD 1 gene offers new hope for improving breast cancer therapy.

This paper proposes a linear eddy-current feature to determine the radius of a metallic ball in a non-contact manner. An electromagnetic eddy-current sensor with two coils is placed co-axially to the metal ball during measurement. It is well known that the distance between the sensor and test piece (i.e. lift-off) affects eddy-current signals. In this paper, it is found that the peak frequency feature of inductance spectrum is linear to the lift-off spacing between the centre of coil and ball. Besides, the slope of peak frequencies versus lift-offs is linked to the radius of ball. The radius of metallic balls is retrieved from the experimental and embedded analytical result of the slope. Measurements have been carried out on 6 metallic balls with different radii. The radius of the metallic ball can be retrieved with an error of less than 2 %.

Background/Aims: Screening for gestational diabetes mellitus (GDM) are currently done at 24 - 28 weeks of conception, missing out on the most vulnerable period of organogenesis and thus preventing clinicians from starting treatments until the late second or third trimester. MicroRNAs (miR) are small non-coding RNA molecules that could aid in detecting or predicting GDM through establishing a novel non-invasive prenatal testing (NIPT) tool. The objective of this study was to summarize the most recent updates on plasma microRNAs as GDM diagnostic biomarkers. Methods: Between April and June 2021, a PubMed literature search was undertaken to review recent articles on human plasma miR associated with GDM. Animal studies and papers that are written in languages other than English were excluded. Only plasma miRNAs were used to avoid coagulation biases. Results: A total of 31 miRNAs were found significantly upregulated in the plasma samples of patients with GDM. It was found mainly during the 2nd or 3rd trimester except for miR-223 and miR-23a that were upregulated at 9 – 11 weeks of gestation. Conclusion: Though extensive prospective cohort studies are required, miR-223 and miR-23a should be considered the most promising to develop a successful NIPT tool because they were found to be upregulated earliest, during the first trimester.

The stress testing methodology should be implemented and applied to the entity's overall financial system at least annually, and if the organization operates in a volatile economy, it should be performed at least twice a year. Finally, managers should include regular training and development sessions for relevant employees of their organization to be fully informed and more informed and informed, considering the evolving science, theory and practicality of a discrete range of stress testing mechanisms that can be appropriately applied to overall financial framework and system of multiple financial institutions and banks. In addition, stress testing is essentially a methodology that collects and analyzes certain future macro-prudential and micro-prudential economic drivers and indicators, the primary purpose of which is to assess the future financial and economic well-being, level of growth and status quo of a financial institution, bank, organization, credit institution or economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. with the primary intention of assessing the future financial and economic well-being, level of growth and status quo of a group of financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically targeted and incorporated into a paper that substantially and broadly discussed and summarized the importance of the feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. with the primary intention of assessing the future financial and economic well-being, level of growth and status quo of a group of financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. the level of growth and status quo of the financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries. region. the level of growth and status quo of the financial institutions, banks, organizations, credit institutions or the economy or the nation as a whole. In addition, several of these reviews were specifically focused and incorporated into the paper, which substantially and broadly discussed and summarized the importance, feasibility and implementation and conclusions of different stress testing approaches for financial institutions and banks, especially in European and Chinese countries.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

There is increasing interest in automating train operations of mainline services, e.g. to increase network capacity. Automatic train operation (ATO) is already achieved by several pilot projects, but not implemented on a large scale. Before the general introduction of new or adapted technologies can have a transformative effect on the operation of such a complex system as train operation on mainlines, they have to pass functional, interoperability and performance tests. A virtual preliminary analysis is one way to ensure a smooth as well as safe introduction and implementation. This paper aims to present an approach that applies to the performance testing of ATO systems. Therefore, methods and test standards for technologies enabling automatic operation in other transport sectors are reviewed. The main findings have been adapted, transformed and combined to be used as a general strategy for virtual performance testing in the railway sector. Specifically, universal performance indicators, namely punctuality, accuracy, energy consumption, safety and comfort, are presented. A layer model for scenario description is adapted from the automotive sector, as well as the definition of different scenario types. Lastly, factors that can influence the performance of an ATO algorithm are identified. To demonstrate the developed approach, a straightforward investigation of a case study is conducted using a microscopic train simulator in combination with an ATO algorithm.

In the advent of COVID-19 pandemic, testing is highly essential to be able to isolate, treat infected persons, and finally curb transmission of this infectious respiratory disease. Group testing has been used previously for various infectious diseases and recently reported for large-scale population testing of COVID-19. However, possible sample dilution as a result of large pool sizes has been reported, limiting testing methods’ detection sensitivity. Moreover, the need to sample all individuals prior to pooling overburden the limited resources such as test kits. An alternative proposed strategy where test is performed on pooled samples from individuals representing different households is presented here. This strategy intends to improve group testing method through the reduction in the number of samples collected and pooled during large-scale population testing. Moreover, it introduces database system which enables continuous monitoring of the population’s virus exposure for better decision making.

The neuroglial extracellular matrix (ECM) provides critical support and physiological cues for the proper growth, differentiation, and function of neuronal cells in the brain. However, in most in vitro settings that study neural physiology, cells are grown as monolayers on stiff surfaces that maximize adhesion and proliferation, and therefore lack the physiological cues that ECM in native neuronal tissues provides. Macromolecular crowding (MMC) is a biophysical phenomenon based on the principle of excluded volume that can be harnessed to induce native ECM deposition by cells in culture. Here, we show that MMC using two species of Ficoll with vitamin C supplementation significantly boosts deposition of relevant brain ECM by cultured human astrocytes. Dopaminergic neurons co-cultured on this astrocyte-ECM bed prepared under MMC treatment showed longer and denser neuronal extensions, a higher number of pre ad post synaptic contacts, and increased physiological activity as evidenced by higher frequency calcium oscillation, compared to standard co-culture conditions. When the pharmacological activity of various compounds was tested on MMC-treated co-cultures, their responses were enhanced, and for apomorphine, a D2-receptor agonist, it was inverted in comparison to control cell culture conditions, thus emulating responses observed in in vivo settings. These results indicate that macromolecular crowding can harness the ECM-building potential of human astrocytes in vitro forming an ultra-flat 3D microenvironment that makes neural cultures more physiological and pharmacological relevant.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

This paper presents an innovative testing framework, testFAILS, designed for the rigorous evaluation of AI Linguistic Systems, with a particular emphasis on various iterations of ChatGPT. Leveraging orthogonal array coverage, this framework provides a robust mechanism for assessing AI systems, addressing the critical question, "How should we evaluate AI?" While the Turing test has traditionally been the benchmark for AI evaluation, we argue that current publicly available chatbots, despite their rapid advancements, have yet to meet this standard. However, the pace of progress suggests that achieving Turing test-level performance may be imminent. In the interim, the need for effective AI evaluation and testing methodologies remains paramount. Our research, which is ongoing, has already validated several versions of ChatGPT, and we are currently conducting comprehensive testing on the latest models, including ChatGPT-4, Bard and Bing Bot, and the LLaMA model. The testFAILS framework is designed to be adaptable, ready to evaluate new bot versions as they are released. Additionally, we have tested available chatbot APIs and developed our own application, AIDoctor, utilizing the ChatGPT-4 model and Microsoft Azure AI technologies

The availability of simple SARS-CoV-2 detection methods is crucial to contain the COVID-19 pandemic. This study examined whether a commercial LAMP assay can reliably detect SARS-CoV-2 genomes directly in respiratory samples without having to extract nucleic acids (NA) beforehand. Nasopharyngeal swabs (NPS, n = 220) were tested by real-time reverse transcription (RT)-PCR and with the LAMP assay. For RT-PCR, NA were investigated. For LAMP, NA from 26 NPS in viral transport medium (VTM) were tested. The other 194 NPS were analyzed directly without prior NA extraction [140 samples in VTM; 54 dry swab samples stirred in phosphate buffered saline]. Ten NPS were tested directly by LAMP using a sous-vide cooking unit. The isothermal assay demonstrated excellent specificity (100%) but moderate sensitivity (68.8%), with a positive predictive value of 1 and a negative predictive value of 0.65 for direct testing of NPS in VTM. The use of dry swabs, even without NA extraction, improved the analytical sensitivity; up to 6% of samples showed signs of inhibition. The LAMP could be performed successfully with a sous-vide cooking unit. This technique is very fast, requires little laboratory resources and can replace rapid antigen tests or verify reactive rapid tests on site.

Background: HIV self-testing (HIVST) is one of the recommended approaches for HIV testing services, particularly for helping reach populations who would not normally access facility-based HIV testing. HIVST must be tailored to different populations to ensure uptake. Objective: The main objective of this study was to develop an acceptable HIVST delivery strategy to help improve urban men’s engagement with HIV services. Methods: We invited key stakeholders for urban men’s HIV services to participate in a co-creation workshop aimed at developing HIVST delivery approaches for urban men, using eThekwini municipality as a study setting. We conducted purposive sampling to include health care users and health care providers, representing a range of views across the public sector and voluntary sector. We employed the Nominal Group Technique (NGT) method for data collection. The NGT workshop was conducted in two consecutive phases: phase one was focused on determining barriers for men’s engagement with the current/facility-based HIV testing services; phase two was aimed at determining HIVST delivery strategies. We used the results of the NGT to design a tailored HIVST strategy for urban men in eThekwini District. Results: Participants identified the following psychological factors as the most important barriers to uptake of HIV testing services by urban men: stigma, ignorance about the importance of testing and testing process as well as fear of positive test results. Key stakeholders suggested internal motivation strategies as a potentially effective approach to support HIVST delivery strategy. Guided by the NGT results, we designed a HIVST delivery strategy that is supported by a risk communication approach Conclusion: We designed an evidence-based risk communication mobile health (mHealth) strategy coupled with SARS COV-2 self-testing tailored to improve men’s uptake of HIVST. A follow-up study to evaluate the feasibility of implementing these approaches is recommended.

Semi-destructive and non-destructive techniques are not commonly used for masonry as they are complex and difficult to perform. This paper describes validation of the following methods: semi-destructive and non-destructive, ultrasonic technique for autoclaved aerated concrete (AAC). The research subject was the compressive strength of AAC test elements with declared various density classes of: 400, 500, 600 and 700 (kg/m3) and various moisture levels. Empirical data including the shape and size of specimens, were established from tests on 494 cylindrical and cuboid specimens, and standard cube specimens 100×100×100 mm using the general relationship for standard concrete (Neville’s curve). The effect of moisture on AAC was taken into account while determining the strength fBw for 127 standard specimens tested at different levels of water content (w = 100%, 67%, 33% 23% and 10%). Defined empirical relations can be used to correct the compressive strength of dry specimens. For 91 specimens 100×100×100 mm, the P-wave velocity cp was tested with the transmission method using using the ultrasonic pulse velocity method with exponential transducers. The curve (fBw – cp) for determining the compressive strength of AAC elements with any moisture level (fBw) was established.

Inhalation is the main route of exposure to airborne pollutants. To evaluate the safety and assess the risks of occupational hazards different testing approaches are used. 3D airway epithelial tissues allow to mimic exposure conditions in vitro, generates human-relevant toxicology data, allows to elucidate mode of action of pollutants. Gilian 3500 pumps equipped with Standard Midget Impingers were used to collect the airborne particulate from woodworking and metalworking environments. EpiAirway™ tissues were used to model half working day (4 h), full working day (8 h), and 3 working day exposures to occupational pollutants. Tissue viability was assessed using MTT assay. RT-qPCR analyses performed to analyze the expression of gelsolin, caspase-3, and IL-6. Tissue morphology was assessed by hematoxylin/eosin staining. Acute exposure to workspace pollutants slightly affected tissue viability and did not change the morphology. Both types of particles suppressed expression of gelsolin, with metalworking samples showing the most pronounced effect. A slight reduction in caspase-3 expression was observed. Particles from metalworking suppressed IL-6 expression. 3D Epithelial tissues can be used to model exposures to airborne pollutants. Exposure to particles from woodworking and metalworking had a minor effect on tissue viability but affected the expression of inflammation and apoptosis-related genes.

This paper presents the development of an underwater crack detection system for structural integrity assessment of submerged structures, like offshore oil and gas installations, underwater pipelines, underwater foundations for bridges, dams etc. Focus is on use of machine learning based approaches. First a detailed literature review of state of the current methods for underwater surface crack detection is presented highlighting challenges and opportunities. An overview of image augmentation approach for creation of underwater optical effects is also presented. Experimental results using standard network based machine learning approach, used for surface crack detection in onshore environment, is presented. Series of Test cases are presented where existing networks performance are improved using augmented images for underwater conditions. The experimental results demonstrate the effectiveness and accuracy of the proposed system in detecting cracks in underwater structures. The system has the potential to improve the safety and reliability of underwater structures and prevent catastrophic failures.

The existence of the hole on a plate affects the calculation of eddy current problems. Consequently, the accuracy for the prediction of the material properties decreases if the effect of the hole is not taken into account. In this paper, a novel analytical method based on the modified integration range is proposed which can address the presence of the hole. Due to the presence of the hole, the conventional Dodd-Deeds analytical solution cannot be used to calculate the inductance change. Therefore, a revised upper integration limit is introduced to replace the original limit -- ∞ when using the co-axially air-core electromagnetic sensor. With the presence of the hole, the magnitude of the received signal reduces, and the peak frequency feature changes. The analytical method is validated by measured and numerical simulation results. It is found that the upper limit is related to the radius of the open hole. With the new technique, the thickness of sample plates with holes can be estimated based on the peak frequency feature.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Acute vertigo and dizziness are frequent presenting symptoms in patients on the emergency department. With a broad differential diagnosis and symptoms/signs often subtle and transient, the diagnostic approach to the dizzy patient remains challenging. Previous work emphasized the value of combining structured history-taking and a targeted examination focusing on subtle oculomotor signs. Here I review different bedside algorithms proposed for the acutely dizzy patient. Comparing area-under-the-curve ROC-characteristics and sensitivity/specificity, highest diagnostic accuracy was observed for algorithms focusing on subtle oculomotor signs. Both the HINTS+ bedside-exam and the STANDING algorithm have demonstrated higher diagnostic accuracy for identifying strokes than early (<24-48h after symptom-onset) MRI-DWI. Importantly, HINTS and STANDING require moderate training to allow reliable application. Thus, for physicians lacking dedicated training, other approaches are needed. Various scores that rely on vascular risk-factors, clinical symptoms and focal neurologic findings have been proposed (e.g., ABCD2-score, PCI-score, TriAGe+-score). While these scores are more readily applicable for frontline providers, they provide intermediate diagnostic accuracy at best and often lack external validation, thus are an insufficient substitute for algorithms assessing subtle oculomotor findings. Providing dedicated training in HINTS+ or STANDING techniques will be key to improve the diagnostic accuracy and to avoid unnecessary brain imaging.

We have previously reported that a single test measuring oVEMP n10 to 4000Hz stimuli (either bone-conducted vibration (BCV) or air-conducted sound (ACS)) provides a definitive diagnosis of semicircular canal dehiscence (SCD) in 22 CT-verified patients with a sensitivity of 1.0 and specificity of 1.0. Such a single short screening test has great advantages of speed, minimizing testing time and the exposure of patients to stimulation. However some studies of the 4000Hz test for SCD have reported sensitivity and sensitivity values somewhat less that what we reported.

The relative dislocation density of aluminum and copper samples is quantitatively measured using linear Resonant Ultrasound Spectroscopy (RUS). For each metallic group, four samples were prepared with different thermomechanical treatments in order to induce changes in their dislocation densities. The RUS results are compared with Nonlinear Resonant Ultrasound Spectroscopy (NRUS) as well as Second Harmonic Generation (SHG) measurements. NRUS has a higher sensitivity by a factor of two to six and SHG by 14% to 62%. The latter technique is, however, faster and simpler. As main a result we obtain a quantitative relation between the changes in the nonlinear parameters and the dislocation density variations, which in a first approximation is a linear relation between these differences. We also present a simple theoretical expression that explains the better sensitivity to dislocation content of the nonlinear parameters with respect to the linear ones. X-Ray diffraction measurements, although intrusive and less accurate, support the acoustics results.

A better understanding of diseases progress in tissues vest on the accurate understanding of tissues under mechanical loading. Also, development of therapies for injuries may depend on the available mechanical data for soft tissues. In this study, the raw data of biaxial tensile testing of sclera soft tissue is presented in this paper. Biaxial mechanical testing of soft tissues presents details understanding of how soft tissues behave when compared to uniaxial testing. Biomechanical properties of soft tissues are vital in the development of accurate computational models. Reliable computational models of studying mechanisms of diseases depends mainly on the accurate and more details mechanical behavior of soft tissues. These accurate and detailed computational models may be utilized to further develop the understanding and therapies of various diseases. The mechanical tensile testing was conducted on the passive sheep sclera. Engineering stress vs strain of several samples of the sheep sclera are further presented determined from force and displacement experimental data. The goal of this paper is to make available biaxial data of sheep sclera soft tissue that can be further utilized.

The emerging industry of offshore wind turbines mounted on floating bases has garnered significant attention from both academia and industry. The desire to understand the complex physics of these floating structures has led to the development of numerical and physical modelling techniques. While physical testing has traditionally been employed, there is a growing focus on cost-effective and accurate high-fidelity numerical modelling as a potential alternative or supplement. However, commonly used numerical engineering tools in the offshore industry are considered mid- to low-fidelity and may lack the desired precision for floating offshore wind turbines (FOWTs). Given the complexity of these simulation codes, it is crucial to validate their accuracy. To address this, the International Energy Agency (IEA) Wind Technology Collaboration Programme initiated various research endeavors, including the Offshore Code Comparison Collaboration (OC3), Offshore Code Comparison Collaboration Continuation (OC4), Offshore Code Comparison Collaboration Continuation with Correlation (OC5), and the recent Offshore Code Comparison Collaboration Continued with Correlation and Uncertainty (OC6) projects. This study offers a comprehensive survey of the simulation tools available for FOWTs which were part of OC projects, focusing particularly on horizontal axis wind turbines (HAWTs) and highlighting their capabilities and fundamental theories.

Cyclic vomiting syndrome (CVS) is a frequently disabling condition defined by severe, discrete, stereotypical episodes of nausea and vomiting. In our previous report [1], a candidate gene list was evaluated in a group of 80 unrelated participants with CVS with extensive genetic sequencing (whole exome/genome). Twenty-two good candidate genes for CVS association were identified, from which a cellular model of aberrant cation transport and energy metabolism was proposed. Herein, we present additional clinical information on those 80 participants, including eight case reports to highlight general principles and clinical practices. Our participants demonstrate substantial phenotypic and genotypic heterogeneity in CVS, including a propensity for specific co-morbidities in the participants and relatives, evolution towards episodes in which vomiting is less apparent, labeling with “non-organic” diagnoses, multiple genes, polygenic inheritance, and association with variants not designated as Pathogenic. Our case reports illustrate how genetic information can guide clinical management and argue to the high clinical utility of appropriate genetic testing and analysis in CVS. Expression profiling of our 22 candidate genes suggests an anatomical model in a unit defined by vagal afferents and adjacent cells. Our models are consistent with multiple current hypotheses of CVS and the efficacy of commonly-recommended treatments.

Human adenoviruses are one of the most important pathogens detected in acute respiratory diseases in pediatrics and immunocompromised patients. In 1953, Wallace Rowe described it for the first time in oropharyngeal lymphatic tissue. To date, more than 85 types of HAdV have been described, with different cellular tropisms. They can cause respiratory and gastrointestinal symptoms, even urinary tract inflammation, although most infections are asymptomatic. However, there is a population at risk that can develop serious and even lethal conditions. These viruses have a double-stranded DNA genome, 25-48 kbp, 90 nm in diameter, without a mantle, stable in the environment, and resistant to fat-soluble detergents. Currently the diagnosis is made with lateral flow immunochromatography or molecular biology through a polymerase chain reaction. The objective of this review is to recognize the variability of HAdV, the pandemic potential that a recombinant could present between HAdV-3 and 7 viral types, known to produce aggressive outbreaks in health facilities. The review determined the characteristics of HAdV, from the infection to treatment, vaccine development and the evaluation of the social determinants of health associated with HAdV, guiding the necessary measures for future sanitary control, and preventing disasters such as the SARS-CoV-2 pandemic.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

Purpose: Determine the internal consistency and reproducibility test-retest of the Barrier Scale for Cardiac Rehabilitation (BSCR) in Colombian population. Methods: 190 patients (67% men, average age = 65 ± 12 years) completed the scale in two moments, with an average of eight days between applications. Cronbach's Alpha and Intraclass Correlation (ICC) coefficients were calculated. Results: The internal consistency of the Colombian version of the BSCR was good (Cronbach's alpha = 0.85). The ICC of the instrument was 0.69 (95% CI 0.61-0.76), 0.78 (95% CI 0.71-0.84) when used in the interview type, and 0.47 (95% CI 0, 21-0.67) when it was self-completing. Conclusions: The EBRC has an acceptable reliability in the Colombian population, however, its reproducibility decreases when it is self-directed. Identifying barriers using this scale will allow developing strategies to increase participation and adherence to cardiac rehabilitation programs focused on the real needs of patients.

This article presents raw data of biaxial tensile measurements of rat heart passive myocardium conducted in lab scale environment. The passive myocardium of the rat was divided into three regions, namely: left ventricle, mid-wall and right ventricle. The biaxial dataset of passive rat myocardia is presented as stress vs strain of the passive rat myocardium in various regions. The determination of valid material properties of the heart plays an important role in the development computational models. These computational models are useful in studying various scenarios and mechanisms of heart diseases. In addition, valid and accurate materials are critical in the development of new therapies. The dataset presented here is useful in the area of soft tissue mechanics including studying the mechanisms of heart diseases such as myocardial infarction. Accordingly, the evaluation of stress and strain in left ventricle, mid-wall and right ventricle was performed.

Online digital mental health communities can contribute to users’ mental health positively and negatively. Yet the measurement of outcomes and impact relating to digital mental health communities is difficult to capture. In this paper we demonstrate the development of an online experience measure for a specific children and young people’s community inside a digital mental health service. The development is informed by three phases: (i) item reduction through Estimate-Talk-Estimate modified Delphi methods, (ii) user testing with participatory action research and (iii) a pilot within the digital service community to explore its use. Rounds of experts talks help to reduce the items. User experience workshops helped to inform the usability and appearance, wording, and purpose of the measure. Finally, the pilot results highlight completion rates, difference in scores for age and community roles and a preference to ‘relate to others’; as a mechanism of support. Outcomes frequently selected in the measure show the importance of certain aspects of the community, such as safety, connection, and non-judgment previously highlighted in the literature. Self-reported helpfulness scales like this one could be used as indicators of meaningful engagement within the community and its content but further research is required to ascertain its acceptability and validity. Phased approaches involving stakeholders and participatory action research enhances the development of digitally enabled measurement tools.

The use of multi-gene panels for germline testing in breast cancer enables the estimation of cancer risk and guides risk-reducing management options for tested individuals and their family members. We performed an analysis in our clinical database to identify breast cancer patients undergoing genetic testing with positive reports. We reviewed positive results with respect to the different levels of information provided in the reports; risk estimation and management, cascade family testing, information from secondary findings and actionable information for treatment decision-making. A total of 415 positive test reports were identified with 57.1%, 18.1%, 10.8% and 13.5% of individuals having pathogenic/likely pathogenic variants in high (BRCA1, BRCA2, PALB2, PTEN, TP53), moderate (ATM, CHEK2, NBN), low (BARD1, BRIP1, CHEK2, MLH1, MSH2, MSH6, NF1, RAD51C) and with insufficient evidence for breast cancer risk genes (FANCA, FANCM, NBN, MRE11, PMS2, RAD50, RAD51B, XRCC2, MUTYH), respectively. 6.7% of individuals were double heterozygotes with two pathogenic variants. Germline findings in 92% of individuals are linked to evidence-based treatment information and receive risk estimates for predisposition to breast and/or other cancer types. The use of germline findings for treatment decision making expands the indication of genetic testing to include individuals that could benefit from targeted treatments.

The paper is focused on the examination of the internal quality of joints created in a multi-material - additive manufacturing process. The main part of the work focuses on experimental production and non-destructive testing of restrained joints of modified PLA (polylactic acid) and ABS (Acrylonitrile butadiene styrene) 3Dprinted on RepRap 3D device that works on the "open source" principle. The article presents the outcomes of non-destructive materials test in the form of the data from the Laser Amplified Ultrasonography, microscopic observations of the joints area and tensile tests of the specially designed samples. The samples with designed joints were additively manufactured of two materials: specially blended PLA (Market name – PLA Tough) and conventionally made ABS. The tests are mainly focused on the determination of the quality of material connection in the joints area. Based on the results obtained, the samples made of two materials were compared in the end to establish which produced material joint is stronger and have a lower amount of defects.

Our primary objectives were a) to determine the need for, and the availability of point-of-care testing (POCT) for infectious diseases and b) to recommend point-of-care testing strategies and spatial care paths (SCPs) that enhance public health preparedness in regional districts of Thua Thien Hue Province (TTHP), Central Vietnam, where we conducted field surveys. Medical professionals in 7 community health centers (CHCs), 7 district hospitals (DHs) and 1 provincial hospital (PH) participated. Survey questions (English and Vietnamese) determined the status of diagnostic testing capabilities for infectious diseases and other acute medical challenges in TTHP. Infectious disease testing was limited: 6 of 7 CHCs (86%) lacked infectious disease tests. One CHC (14%, 1/7) had two forms of diagnostic tests available for the detection of Malaria. All CHCs lacked adequate microbiology laboratories. District hospitals had few diagnostic tests for infectious diseases (Tuberculosis, Syphilis), blood culture (29%, 2/7), and pathogen culture (57%, 4/7) available. The PH had broader diagnostic testing capabilities but lacked preparedness for highly infectious disease threats (e.g., Ebola, MERS-CoV, SARS, Zika, and Monkeypox). All sites reported having COVID-19 rapid antigen tests; COVID-19 RT-PCR tests were limited to higher tier hospitals. We conclude that infectious disease diagnostic testing should be improved and POC tests must be supplied near patients’ homes and in primary care settings for the early detection of infected individuals and mitigation of the spread of new COVID-19 variants and other highly infectious diseases.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

Meier–Gorlin syndrome (MGS) is a rare genetic developmental disorder that causes primordial proportional dwarfism, microtia, absent or hypoplastic patellae and other skeletal anomalies. Overlapping skeletal symptoms make MGS difficult to diagnose clinically. We describe a 3-year-old boy with short stature, recurrent respiratory infections, short-rib dysplasia, tower head and facial dysmorphisms who was admitted to the Tomsk Genetic Clinic to verify a clinical diagnosis of Jeune syndrome. Clinical Exome sequencing revealed two variants (compound heterozygosity) in the ORC6 gene: c.2T&gt;C(p.Met1Thr) and c.449+5G&gt;A. In silico analysis showed the pathogenicity of these two mutations and predicted a decrease in donor splicing site strength for c.449+5G&gt;A. An in vitro minigene assay demonstrated that variant c.449+5G&gt;A causes a complete skipping of exon 4 in ORC6 gene. The parents asked for urgent prenatal testing for MGS for the next pregnancy, but it ended in a miscarriage. Thus, this case report may help to prevent MGS misdiagnosis in the future. We also performed in silico and functional analyses of ORC6 mutations and developed a restriction fragment length polymorphism and haplotype-based short-tandem-repeat assay for prenatal genetic testing for MGS. These findings should elucidate MGS aetiology and improve the quality of genetic counselling for affected families.

COVID-19 has harmful impact on health. It is especially important for endurance athletes (EAs). Sleep and psychology influence sport performance. Aims of this study were: (1) investigation of the consequences of mild COVID-19 on sleep and psychology and (2) assessment of the conse-quences of the infection on cardiopulmonary exercise test (CPET) results. 49 EAs (males= 43; 87.76%, females= 6; 12.24%, age= 39.9±7.8 years, height= 178.4±6.8 cm, weight= 76.3±10.4 kg; BMI= 24.0±2.6 kg·m−2) underwent maximal cycling or running CPET pre- and post- COVID-19 and completed a survey. Exercise performance was deteriorated after COVID-19 (maximal oxy-gen uptake; VO2max= 47.81±7.81 vs 44.97±7.00 ml·kg·min−1 respectively pre- and post- infection; p<0.001). Waking up at night affected heart rate (HR) at the respiratory compensation point (RCP) (p=0.028). Sleep time influenced pulmonary ventilation (p=0.013), breathing frequency (p=0.010), and blood lactate concentration (Lac) (p=0.013) at RCP. Maximal power/speed (p=0.046) and HR (p=0.070) linked with the quality of sleep. Stress management and relaxation techniques linked with VO2max (p=0.046), maximal power/speed (p=0.033), and maximal Lac (p=0.045). Cardiorespiratory fitness was deteriorated after mild COVID-19 and was correlated with sleep and mental health. Medical Professionals should encourage EAs to maintain proper mental health and sleep after COVID-19 infection to facilitate recovery.

This paper proposes an optimal trading algorithm based on a novel application of the conventional Control Engineering (CE). We consider a fundamental CE concept, namely, the feedback control and apply it to the Algorithmic Trading (AT). The concrete feedback control strategy is designed in a form of the celebrated Proportional-Integral-Derivative (PID) model. The highly fluctuating nature of the modern financial markets has led to the adoption of a model-free realisation of the generic PID framework. The control theoretical methodology we propose is combined with the advanced statistics for the historical market data. We obtain a specific log-normal probability distribution function (pdf) associated with the specific quantities associated with the available stock data. The empirical log-normal pdf mentioned above makes it possible the necessary PID gains optimization. For this aim, we apply the data-driven optimization approaches and consider the corresponding Monte Carlo solution procedure. The optimized PID trading algorithm we propose is also studied in the Fourier analysis framework. This equivalent frequency domain representation involves a new concept in the financial engineering, namely, the "stock market energy" concept. For the evaluation, we implement the proposed PID optimal trading algorithm and develop a Python based prototype software. We finally apply the corresponding prototype software to a dataset from the Binance BTC / USDT stock market. The experimental result illustrates the implementability of the proposed optimal PID trading scheme and also shows the effectiveness of the proposed CE methods in the modern AT.

Guided by the Conceptual Model of Implementation Research, we explored the acceptability, appropriateness, and feasibility of: 1) automated screening approaches utilizing existing health data to identify those who require subsequent diagnostic evaluation for familial hypercholesterolemia (FH) and 2) family communication methods including chatbots and direct contact to communicate information about inherited risk for FH. Focus groups were conducted with 22 individuals with FH (2 groups) and 20 clinicians (3 groups). These were recorded, transcribed, and analyzed using deductive (coded to implementation outcomes) and inductive (themes based on focus group discussions) methods. All stakeholders described these initiatives as: 1) acceptable and appropriate to identify individuals with FH and communicate risk with at-risk relatives; and 2) feasible to implement in current practice. Stakeholders cited current initiatives, outside of FH (e.g., pneumonia protocols, colon cancer and breast cancer screenings), that gave them confidence for successful implementation. Stakeholders described perceived obstacles, such as nonfamiliarity with FH, that could hinder implementation and potential solutions to improve systematic uptake of these initiatives. Automated health data screening, chatbots, and direct contact approaches may be useful for patients and clinicians to improve FH diagnosis and cascade screening.

For polymicrobial infections, AtbFinder utilizes a novel paradigm of the population response to antibiotics, enabling bacterial growth in the form of a mixed microbial community and selecting the antibiotics targeting not only the principal pathogen, but also those bacteria that support their growth. TGV medium allowed culturing a more diverse set of bacteria from polymicrobial biospecimens, compared with that achieved with the standard media and enabled, already within 4h, accurate selection of the antibiotics that completely eliminated all cultivatable bacteria from clinical samples. In conclusion, AtbFinder system may be a valuable tool in improving antibiotic selection, enabling targeted empirical therapy and accurate antibiotic replacement, which is especially important in high-risk patients.

The Developing Countries Vaccine Manufacturing Network coordinated a multi-laboratory study funded by the US National Institute for Innovation in Manufacturing Biopharmaceuticals to assess the performance of the Pertussis Serological Potency Test (PSPT) in the laboratories of seven whole-cell pertussis vaccine (wP) manufacturers and three National Control Laboratories based in Southeast Asian countries. To this end, common protocols for the immunization of mice and serological testing by ELISA were shared with all laboratories. Each laboratory used their own wP vaccines and the reference vaccine routinely used in the regulatory required mouse protection test (MPT) and assayed the products both in the MPT and PSPT. Whereas in all laboratories the PSPT showed decreased serum IgG levels after immunization with sub-potent compared to potent final batches, some issues were encountered during execution of the assay, which prevented drawing of definitive conclusions on assay performance. Nevertheless, the study provided the participants with the opportunity to familiarize themselves with the PSPT protocols and revealed the next steps to be addressed for implementation of the method.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

This paper describes a new optimization methodology of testing vector sets reduction for testing of soft-processor cores and their individual blocks. The deterministic test vectors both for whole core and its individual blocks are investigated that significantly reduce the testing time and amount of test data that needs to be stored on the tester memory. The processor executes an assembler program which together with determined testing vectors ex-ercise its functionality. The new BIST methodology applicable at industrial testing of processor cores, diagnostics and dynamic reconfiguration of FPGA is proposed. This novel methodology combined with dynamic reconfiguration of FPGAs can be profitable applied for missions-critical i.e. FPGAs operate in space, or other difficult condition where are explore on radiation. Experimental results demonstrate that the proposed approach reduces many times testing time.

TThe aim of the work is to present a newly developed stand and methodology of accelerated tests of fatigue strength of flexible propellers and fins. The paper presents the design and concepts of the measuring elements used in the research. Test methodology and water stressing were devel-oped. The mechanical properties of the following materials were presented: Arnitel EL-550 and QUEO 8230 with the addition of PP / EVA 50/50 (polypropylene / ethylene-vinyl acetate) - in the proportion of 70/30 (QUEO 8230 / additive). The constructed test stand and a new method of fa-tigue testing of biomimetic fins made it possible to determine the number of fin movement cy-cles under a given load, which may facilitate the determination of a warranty for a newly intro-duced product. The current consumption by the fin drive and video monitoring allowed for the selection of the range of the number of movement cycles and the determination of the moment of fatigue cracks until the fin structure loses its capacity. During the analysis, the test results showed that the fins made of Arnitel EL-550 did not show changes in the measured values of the current and the force generated by the fin. For a fin made of QUEO 8230, at 35,000 cycles, there is a decrease in the current and force consumed, which indicates the initiation of fatigue damage to the fin. The performed tests can be the basis for the development of standards for the fatigue strength of flexible propellers.

SARS-CoV-2, influenza A/B virus (IAV/IBV) and respiratory syncytial virus (RSV) are among the common viruses causing acute respiratory infections. Clinical diagnosis to differentiate these viruses is challenging due to similar clinical presentations, thus laboratory-based real-time RT PCR is the gold standard for diagnosis. The study aimed to evaluate the diagnostic performance of STANDARD M10 Flu/RSV/SARS-CoV-2 (SD Biosensor Inc, Seoul, Korea). This retrospective study was conducted with archived respiratory samples positive and negative for SARS-CoV-2, IAV, IBV or RSV. The evaluation study involved a total of 322 respiratory samples comprising 215 positive samples (49 SARS-CoV-2, 48 IAV, 53 IBV, 65 RSV) and 107 negative samples. All samples were tested with both STANDARD M10 and either Xpert Xpress SARS-CoV-2 or Xpert Xpress Flu/RSV (Cepheid, USA). The sensitivity, specificity, positive predictive value and negative predictive value rates of STANDARD M10 were very similar to Xpert Xpress SARS-CoV-2 or Xpert Xpress Flu/RSV ranges for each virus (98-100%). The overall agreement was 99.4% with 99.1% agreement for positive samples and 100% agreement for negative samples. In conclusion, the STANDARD M10 point-of-care test is suitable for rapid simultaneous detection of SARS-CoV-2, IAV, IBV and RSV.

Conventional diagnostic techniques are based on utilization of analyte sampling, sensing and signalling on separate platforms for detection purposes, that must be evaded and integrated to a single step procedure in point of care (POC) testing devices. Therefore, the trend has been shifted towards utilization of microfluidic platforms for detection of analytes in biochemical, clinical and food technology due to its being expeditious. Microfluidic systems moulded with polymer substances or glass offer specific and sensitive detection of infectious and non-infectious diseases by providing innumerable benefits including less cost, good biological affinity, strong capillary action and simple process of fabrication. In the case of nucleic acid-based nanosensors, there are some challenges that need to be addressed such as cellular lysis, isolation and amplification of nucleic acid required to be accomplished prior to its detection. To avoid utilization of laborious steps for executing these steps, advances have been deployed in this perspective for on-chip sample preparation, amplification and detection which not only improves sensitivity and selectivity but also saves time and resources. This review emphasizes the significance of microfluidic technology for nucleic acid detection of infectious and non-infectious diseases. The implementation of isothermal amplification in concomitance with lateral flow assay greatly increases the binding efficiency of nanoparticles and biomolecules, improves limit of detection and sensitivity. Most importantly deployment of paper-based material made of cellulose reduces the overall cost. Microfluidic technology in nucleic acid testing has been discussed by explicating its applications in different fields. This review concludes with the prospects and proposes future directions in microfluidic based methods in disease diagnosis.

In the rapidly advancing field of Artificial Intelligence (AI), this study presents a critical evaluation of the resilience and cybersecurity efficacy of leading AI models, including ChatGPT-4, Bard, Claude, and Microsoft Copilot. Central to this research is the use of innovative adversarial prompts designed to rigorously test the content moderation capabilities of these AI systems. The study introduces new types of adversarial tests and the Response Quality Score (RQS), a metric specifically developed to assess the nuances of AI responses. Additionally, the research spotlights FreedomGPT, an AI tool engineered to optimize the alignment between user intent and AI interpretation. The empirical results from this investigation are pivotal for assessing the current robustness and security of AI models. They highlight the necessity for ongoing development and meticulous testing to bolster AI defenses against an array of adversarial challenges. Importantly, the study also delves into the ethical and societal implications associated with employing advanced 'jailbreak' techniques in AI testing. The findings are significant for understanding AI vulnerabilities and formulating strategies to enhance the reliability and ethical soundness of AI technologies, paving the way for safer and more secure AI applications.

In an industrial environment, the quality assurance of weld seams requires extensive efforts. The most commonly used methods for that are expensive and time-consuming destructive tests, since quality assurance procedures are difficult to integrate into production processes. Beyond that, available test methods allow only the assessment of a very limited set of characteristics. They are either suitable for determining selected geometric features or for locating and evaluating internal seam defects. The presented work describes an evaluation methodology based on microfocus X-ray computed tomography scans (µCT scans) which enable the 3D characterization of weld seams, including internal defects such as cracks and pores. A 3D representation of the weld contour, i.e., the complete geometry of the joint area in the component with all quality-relevant geometric criteria, is an unprecedented novelty. Both the dimensions of the weld seam and internal defects can be revealed, quantified with a resolution down to a few micrometers and precisely assigned to the welded component. On the basis of the methodology developed within the framework of this study, the results of the scans performed on the alloy AA 2219 can be transferred to other aluminum alloys. In this way, the data evaluation framework can be used to obtain extensive reference data for the calibration and validation of inline process monitoring systems employing Deep Learning-based data processing.

To improve accessibility, this article describes a static, four-legged, walker that can be constructed from materials and fasteners commonly available from hardware stores coupled by open-source 3-D printed joints. The designs are described in detail, shared under an open-source license, and fabricated with a low-cost open-source desktop 3-D printer and hand tools. The resulting device is loaded to failure to determine the maximum load that the design can safely support in both vertical and horizontal failure modes. The experimental results showed the average vertical failure load capacity was 3680±694.3N, equivalent to 375.3±70.8kg of applied weight with the fractured location at the wood dowel handlebars. The average horizontal load capacity was 315.6±49.4N, equivalent to 32.2±5.1kg. The maximum weight capacity of a user of 187.1±29.3kg was obtained, which indicates the open-source walker design can withstand the weight requirements of all genders with a 95% confidence interval that includes a safety factor of 1.8 when considering the lowest deviation weight capacity. The design has a cost at the bottom of the range of commercial walkers and reduces the mass compared to a commercial walker by 0.5kg (19% reduction). It can be concluded that this open-source walker design can aid accessibility in low-resource settings.

Smartphone-based point-of-care testing (POCT) is rapidly emerging as an alternative to traditional screening and laboratory testing, particularly in resource-limited settings. In this proof-of-concept study, we present a smartphone- and cloud-based artificial intelligence quantitative analysis system (SCAISY) for relative quantification of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2)-specific IgG antibody lateral flow assays that enables rapid and accurate evaluation of test strips. By capturing an image with a smartphone camera, SCAISY quantitatively analyzes antibody levels and provides results to the user. We analyzed changes in antibody levels over time in over 248 individuals, including vaccine type, number of doses, and infection status, with a standard deviation of less than 10%. We also tracked antibody levels in six participants before and after SARS-CoV-2 infection. Finally, we examined the effects of lighting conditions, camera angle, and smartphone type to ensure consistency and reproducibility. This study suggests that SCAISY is a simple and powerful tool for real-time public health surveillance, enabling the acceleration of quantifying SARS-CoV-2-specific antibodies generated by either vaccination or infection and tracking of personal immunity levels.

The reported study was devoted to the investigation of viscoelastic behavior for solid and porous ultra-high-molecular-weight polyethylene (UHMWPE) under compression. The obtained experimental stress curves were interpreted using a two-term Prony series to represent the superposition of two coexisting activation processes corresponding to long molecular (~160 s) and short structural (~20 s) time scales, respectively, leading to good statistical correlation with the observations. In the case of porous polymer, the internal strain redistribution during relaxation was quantified using Digital Image Correlation (DIC) analysis. The strongly inhomogeneous deformation of the porous polymer was found not to affect the relaxation times. In order to generalize the results to three dimensions, X-ray tomography was used to examine the porous structure at the macro- and micro-scale levels. DIC analysis revealed positive correlation between the applied force and relative density. The apparent stiffness variation for UHMWPE foams with mixed open and closed cells was described using a newly proposed three-term expression. Furthermore, the in situ tensile loading and X-ray scattering study was applied for isotropic solid UHMWPE specimens to investigate their parameters of internal structure during orientation and stress relaxation process at another mode.

In Los Angeles, at one point, the Covid-19 testing positivity rate was 6.25%, or one in sixteen. This translates to, on average, one in sixteen specimens testing positive and the vast majority testing negative. Usually, we run sixteen tests on sixteen specimens to identify the positive one(s). This process can be time consuming and expensive. Since a group of negative specimens pooled together for testing will produce a negative result, one single test could potentially eliminate many specimens. Only when the pooled specimen tests positive do we need further testing to identify the positive one(s). Based on this concept, we designed a strategy that will identify the positive specimen(s) efficiently. Assuming one in sixteen specimens is positive, we find that only four tests are needed. Furthermore, we can run them simultaneously, saving both resources and time. Although, in the real world, we cannot make the assumption of only one positive specimen, the same strategy works with slight modification and proves to be much more efficient than the conventional testing. Our strategy returns an answer 48% of the time in four tests and one time cycle. Overall, the average number of tests is seven or eight depending on the follow-up testing, and the average time cycle is about one and a half.

The ABCDEFG Protocol provides an evolving tool for imposing structure on the flow of Covid infection information obtained from community testing, collective policy and individual compliance. ABCDEFG Protocol could not assume soundness, invariance, symmetry and completeness of the available information and relied on signaling game theory to design solutions that could evolve with the variable narratives, theories, individual utilities and pathogen variants. Thus, ABCDEFG Protocol suggests a novel and a very flexible pool-testing and badging protocol in the context of controlling contagious epidemics and tackling the far-reaching associated challenges, including understanding and evaluating individual and collective risks of returning prior infected individuals to normal society and other economic and social arrangements and interventions to protect against disease. AbCDEFG Proto uses both control theoretic and game theoretic mathematical models that may be centralized (an optimizing policy maker mandates behavior based on estimated models) or decentralized (a strategizing individual selects their behavior based on available asymmetric information). ABCDEFG protocol demonstrates how society can continue to carry out plausible economic activities in addition to controlling the prevalence of a contagious disease by keeping the number of infected people below a desired limit without compromising an individuals' privacy despite the presence of deception and selfishness among people, and limitations of available resources. Different types of badges would come with different restrictions. Badges would be reissued periodically by third-party testing centers via suitably frequent pool testing of samples of the participants. The size of the pools, frequency of tests, and allowable activities for people with a given type of badge would depend on the available resources, the prevalence of the disease, and the efficacy of the equipment used in the tests.

Cystic fibrosis (CF) is characterized by mutations of CFTR that lead to increased viscous secretions, bacterial colonization and recurrent infections. Chronic P. aeruginosa infection in persons with CF is associated with progressive and accelerated lung function decline despite aggressive antibiotic treatment. We report the management of respiratory infections in persons with CF with antibiotic therapy that was based on the recommendations of AtbFinder, a novel, rapid, culture-based diagnostic test system that employs a novel paradigm of antibiotic selection. AtbFinder mimics bacterial interactions with antibiotics at concentrations that can be achieved in affected tissues or organs, and models conditions of interbacterial interactions within polymicrobial biofilms. This open-label, single-arm, investigator‐initiated clinical study was designed to identify the efficacy of antibiotics selected using AtbFinder in persons with CF. Microbiological and clinical parameters were assessed following the change of antibiotic therapy to antibiotics selected with AtbFinder between January 2016 and December 2018 and retrospectively compared with clinical data collected between January 2013 and December 2015.We enrolled 35 persons with CF (33 with chronic P. aeruginosa colonization). Antibiotics selected using AtbFinder resulted in clearance of P. aeruginosa in 81.8% of subsequent cultures, decreased pulmonary exacerbations from 1.21 per patient per annum to 0, and an increase in predicted FEV1% up to 28.4% from baseline. The number of systemic antibiotic courses used in patients after switching to the AtbFinder selected therapy was reduced from 355 to 178. These findings describe the superiority of antibiotic regimens selected with AtbFinder compared with routine antimicrobial susceptibility testing.

In response to the growing inspection demand exerted by process automation in component manufacturing, Non-destructive testing (NDT) continues to explore automated approaches that utilize deep learning algorithms for defect identification, including within digital X-ray radiography images. This necessitates a thorough understanding of the implication of image quality parameters on the performance of these deep learning models. This study investigates the influence of two image quality parameters, namely Signal-to-Noise Ratio (SNR) and Contrast-to-Noise Ratio (CNR), on the performance of U-net deep learning segmentation model. Input images were acquired with varying combinations of exposure factors such as kilovoltage, milli-ampere, and exposure time, which altered the resultant quality. The data was sorted into 5 different datasets according to their measured SNR and CNR values. The deep learning model was trained 5 distinct times, utilizing a unique dataset for each training session. Training the model with high CNR values yielded an intersection over Union (IoU) metric of 0.9594 on test data of the same category but drops to 0.5875 when tested on lower CNR test data. The result in this study emphasizes the importance of achieving a balance in training dataset according to the investigated quality parameters, to enhance the performance of deep learning segmentation models in NDT radiography applications.

Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

Globally, the use of whole-cell matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) in clinical microbiology laboratories has increased considerably. With the rapid growth of artificial intelligence technology, there is an increasing number of areas devoted to solving problems by implementing machine learning-based methods. Applying the use of artificial intelligence to the analysis of the massive amount of information obtained in the mass spectrum derived from MALDI-TOF MS should be a breakthrough in clinical microbiology. Specifically, it would facilitate a more rapid and accurate strain typing or antibiotic susceptibility test (AST) based on whole-cell MALDI-TOF MS spectra, and hence, it is a promising solution. Even though the reproducibility of peaks could result in some critical problems, computational methods have been developed to address this issue. Therefore, clinical microbiologists are able to perform strain typing or an AST as smoothly and easily as identifying species by using MALDI-TOF MS and artificial intelligence.

This article is some review of results that were obtained at 2007-2021 years development of “The Information as Absolute” concept and the informational physical model, which is based on the concept; including a number of fundamental physical problems are briefly considered in framework of the conception and the model. Recently in physics there are several publications, that present lists of the problems. However, those lists are essentially incomplete, for at least two reasons. Firsts of all, a number of phenomena are studied traditionally by philosophy, and so corresponding problems are usually considered to be “metaphysical”. However, they relate also to some concrete physical phenomena. For example, physics evidently studies Matter, and so the metaphysical problems “what is ontology of Matter”, “what is “Space”, “Time” and a few other physical phenomena and notions as well, are really a Meta-physical problems “what does physics study?” There are other fundamental physical problems, which are not considered as such in physics, and are absent in the “fundamental problems lists”. Those include the problems, which really exist, yet are incorporated into standard physical theories, and so are fundamental “implicitly”, which in physics are “solved by default” ‒ and mostly erroneously. Note, though, that a number of “Meta-physical”, and concrete fundamental, problems more in detail are considered in the paper “The Informational Conception and Basic Physics”, https://arxiv.org/abs/0707.4657, v5 (2021), so this paper is, in certain sense, an expanded conclusion of this paper, which includes, correspondingly, more in detail consideration of some more general physical problems; and, besides, in this article, the problem “what are Gravity and Electric Forces” is essentially clarified comparing with the arXiv 2021 paper version above. Besides, the concrete problem “What is Life”, and the rational cosmological model, where a few vague points in standard cosmology rather probably are rationally clarified, while the fundamental problem “matter – antimatter asymmetry” in Matter is solved practically for sure, are considered, and one of recently published rather complete “lists of fundamental problems” is commented in Appendix.

Basketball playing entails the repetitive performance of short intense actions using lower limb explosive power. As such, it is important to measure this capability in basketball players, especially among young players, and to optimize training programs and game plans. After presenting an in-depth understanding of the specific physiological requirements when playing basketball, as well as the type of movements required, The aim of this review is to better understand the importance of the physiological energy systems in basketball, to examine the contribution of each energy system and, accordingly, to heighten awareness of the importance and dominance of the alactic anaerobic physiological system in basketball, for actions requiring high level explosive power. This review of the literature depicts the horizontal and vertical physical movements and physiological requirements entailed in playing basketball, and presents eight standardized anaerobic alactic measurement tools relevant to the game. As some of these tests suit a number of ball games, the findings of this review article are important for making order of the elements unique to basketball as well as additional parameters to consider when testing basketball players. By reliably and validly testing the anaerobic alactic capabilities of basketball players, test results can be used for training purposes and for improving game outcomes. Despite the fact that much of the information in this review is familiar to coaches, highlighting the specific needs of basketball may help them to choose the most suitable tools, and may also shed light on new directions for developing basketball-specific assessment tests.

The purpose of this work was to evaluate a novel methodology developed by Digital Blood Corporation (DBC) to calculate critical blood values using four non-invasive measured values as input. The values obtained using a point-of-care testing (POCT) device were utilized for comparison and reference. Radial arterial blood was collected for the POCT comparator analysis using the Abbott i-STAT^® device. The non-invasive methodology from DBC requires four parameters to be directly measured: temperature, hemoglobin, pO2, and pCO2. Subsequently, sodium, potassium, chloride, ionized calcium, total carbon dioxide, pH, bicarbonate, and oxygen saturation are calculated using an algorithm. The agreement between the POCT and DBC’s methodology was analyzed using Bland-Altman difference plots. For a second data set, pO2 and pCO2 values collected with the POCT were used as input for DBC’s algorithm to test its robustness. Data from 37 healthy ambulatory individuals, mean age: 42.4 + 13 years; range: 18-64 years, were included in the primary analysis. In the case of the non-invasive gained four input values the greatest variation between POCT and DBC’s approach was observed for pO2 and consequently for algorithm values that depend upon pO2 precision. Replacing transcutaneous pO2 and pCO2 with POCT values demonstrates the principal ability of DBC’s algorithm to predict the additional 8 blood values in sufficient agreement with a standard POCT device in healthy patients. The algorithm developed by DBC appears to be robust in the case of healthy patients but does need the four measured input values with preciseness comparable to a POCT device to give reliable and clinically relevant results. The present study thus serves as a proof of concept to facilitate future study and further development of this methodology into a non-invasive device.

Long read sequencers, known for their effectiveness in detecting genomic structural variations (SV), are becoming a standard in comprehensive genetic analysis. In preimplantation genetic testing (PGT) for SV carriers, information on breakpoint junctions is required for the determination of carrier status in embryo selection. These sequencers are employed for challenging cases involving SVs that are difficult to analyze with conventional cytogenetical methods or detailed junctions of chromosomal translocations, providing valuable insights. They also play a crucial role in acquiring simultaneous information on surrounding single-nucleotide polymorphisms (SNPs) around causative variants in PGT. Despite their advantages, challenges related to sequencing accuracy and testing costs exist. Thus, understanding long read sequencers’ characteristics is essential for their effective utilization. This review summarizes the advanced applications of long read sequencers in preclinical workups and their integration into PGT. It also highlights in-house clinical cases, showing the implementation of long-read sequencing and discussing prospects in the field.

The FDA has concluded that a biosimilar candidate capable of demonstrating pharmacodynamic biomarkers in a healthy subject need not be tested for clinical efficacy in patients, regardless of if the biomarker correlates with clinical response. Since monoclonal antibodies (mAbs) do not trig-ger pharmacodynamic response, they can be substituted with robust functional disqualifying them for this waiver that can be overcome by allowing comparison of functional properties that eventually result in clinical response. This suggestion is based on the FDA's preference for more sensitive testing methods. However, clinical efficacy testing in patients is the least sensitive method, as confirmed by statistical modeling, a fact that regulatory agencies need to admit. In this paper, I present a logical and rational argument to establish the biosimilarity of products that do not have pharmacodynamic biomarkers based on their orthogonally proven functional bio-similarity. This understanding will significantly lower the development cost of biosimilars, a goal that the FDA outlined in all its guidance. Keywords: biosimilarity 1; biosimilars 2; pharmacodynamic biomarkers 3; monoclonal antibodies 4; FDA 5; clinical efficacy testing in healthy subjects 6; clinical efficacy testing in patients 7; functional assays 8; receptor binding 9.

Three-point shooting plays an important role in determining the outcome of the basketball games, and could be relevant for player selection. However, there has been little research into the relationship between basketball players' physical capacities, metabolic capacities and three-point shooting accuracy, particularly among female players. The aim of this study was to examine the relationship between physical capacities, metabolic capacities and dynamic three-point shooting accuracy in female professional basketball players. Twelve female professional basketball players from the Women’s Chinese Basketball Association (WCBA) league (age: 19.04±1.31 years, height: 181.33±4.90cm, playing experience: 7.83±1.7 years) were recruited for this study. Pearson correlations and multiple linear regression analysis were run to assess the relationship between physical capacities, metabolic capacities and dynamic three-point shooting. Results showed that coordination, balance, core strength and relative average power were positively correlated with the three-point shooting accuracy (r>0.58, P<0.05), while no other variables showed significant correlations. The current study suggests that coaching staff should consider coordination, balance, core strength and anaerobic capacities when selecting players as well as in their training periodization if three-point shooting accuracy is considered relevant.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

Foundational and state-of-the-art anomaly detection methods through power system state estimation are reviewed. The traditional components for bad data detection such as chi-square testing, residual-based methods, and hypothesis testing are discussed to explain the motivations for recent anomaly detection methods given the increasing complexity of power grids, energy management systems, and cyber-threats. In particular, state estimation anomaly detection based on data-driven quickest change detection and artificial intelligence are discussed and directions for research are suggested with particular emphasis on considerations of the future smart grid.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

Alternative food sources are essential in both low-resource settings or during emergencies like abrupt sunlight reduction scenarios. Seaweed presents a promising option but requires investigation into the viability of unconventionally sourced ropes for harvesting. As such, a low-cost reliable method to test the tensile strength of rope is needed to validate alternative materials for use in harvesting seaweed. Unfortunately, commercial rope testing jigs alone range in price from several thousand to tens of thousands of dollars. To fill this need, this article reports on an open-source design for tensile strength rope testing hardware. The hardware design focuses on using readily available parts that can be both sourced from a hardware store and manufactured with simple tools to provide for the greatest geographic accessibility. The jig design, which can be fabricated for CAD$20 is two to three orders of magnitude less expensive than commercially available solutions. The jig was built and tested using a case study example investigating denim materials (of 1 5/8”, 3 1/4", 4 7/8”, 6 1/2", and 8 1/8” widths) as a potential alternative rope material for seaweed farming. Denim demonstrated strength up to 1.65kN for the widest sample and the jig demonstrated sufficient strength and stiffness for operating at forces below 4kN. The results are discussed and areas for future improvements are outlined to adapt the device to other circumstances and increase the strength of materials that can be tested.

The question whether a given set of test items can be considered “identical” is often addressed in terms of the homogeneity of the test material from which said items were taken. However, for some types of matrices – in particular, for matrices consisting of minute separate particles, only some of which carry the analyte under consideration – even in the case of homogenous test material, an irreducible source of variability between test items may remain: the fundamental variability. In this paper, the concept of fundamental variability is explained, and procedures for reducing and characterizing it are described.

Insecticide testing facilities that evaluate a variety of vector control products may generate large amount of hazardous wastes from routine operations. These wastes originate from degraded technical grade materials, sprayed substrates, redundant stock or working insecticidal solutions. The washing of Long-Lasting Insecticidal Nets (LLINs) during preparation for laboratory and experimental hut trials also contribute to waste water with insecticide content. Human and environmental exposure to insecticidal waste can occur during transport, categorization, storage and disposal in resulting in environmental pollution and potential health effects. Various national and international guidelines have been devised for safe disposal and should be strictly followed to avoid adverse effects on humans or environment. The current paper describes a case study from insecticide test facility in north-eastern Tanzania in management of insecticidal waste.

Soybean with insignificant differences in appearance have large differences in their internal physical and chemical components, therefore follow-up storage, transportation and processing require targeted differential treatment. A fast and effective machine learning method based on hyperspectral data of soybean for pattern recognition of categories is designed as a non-destructive testing method in this paper. A hyperspectral-image dataset with 2299 soybean seeds in 4 categories is collected; Ten features is selected by extreme gradient boosting algorithm from 203 hyperspectral bands in range 400 to 1000 nm; A Gaussian radial basis kernel function support vector machine with optimization by the Tree-structured Parzen Estimator algorithm is built as TPE-RBF-SVM model for pattern recognition of soybean categories. The metrics of TPE-RBF-SVM are significantly improved compared with other machine learning algorithms. The accuracy is 0.9165 in the independent test dataset which is 9.786% higher for vanilla RBF-SVM model and 10.02% higher than the extreme gradient boosting model.

1) Background: Genomic medicine harbors the real potential to improve the health and healthcare jour-ney of patients, care provider experiences, and improve health system efficiency – even reducing health care costs. There is expected to be an exponential growth in medically necessary new genome- based tests and test approaches in coming years. Testing can also create scientific research and commercial opportu-nities beyond healthcare decision-making. The purpose of this research is to generate a better under-standing of Canada’s state of readiness for genomic medicine, and to provide some insights for other healthcare systems; (2) Methods: a mixed-methodsapproach of literature review and key informant in-terviews with a purposive sample of experts was used. Health system readiness was assessed using a pre-viously published set of conditions. (3) Results: Canada has created some of the established conditions but more needs to be done to improve the state of readiness for genome-based medicine. Important gaps are the need for linked information systems and data integration; evaluative processes that are timely, and transparent; navigational tools for care providers; dedicated funding to facilitate rapid onboarding and supports test development and proficiency testing; and broader engagement with a broader set of inno-vation stakeholders. These findings highlight the known role of organizational context, social influence, and other factors that are known to affect the diffusion of innovation within health systems

Growth environment greatly alters many facets of pathogen physiology, including pathogenesis and antimicrobial tolerance. The importance of host-mimicking environments for attaining an accurate picture of pathogen behaviour is widely recognised. Whilst this recognition has translated into the extensive development of artificial cystic fibrosis (CF) sputum medium, attempts to mimic the growth environment in other respiratory disease states have been completely neglected. The composition of the airway surface liquid (ASL) in different pulmonary diseases is far less well characterised than CF sputum, making it very difficult for researchers to model these infection environments. In this review we discuss the components of human ASL, how different lung pathologies affect ASL composition, and how different pathogens interact with these components. This will provide researchers interested in mimicking different respiratory environments with the information necessary to design a host-mimicking medium, allowing for better understanding of how to treat pathogens causing infection in these environments.

Introduction: Mucopolysaccharidosis type I (MPSI) is an autosomal recessive lysosomal storage disorder characterized by deficient or absent α-L-iduronidase (IDUA) enzyme activity due to pathogenic variants in IDUA gene. Early treatment with hematopoietic stem cell transplantation and/or enzyme replacement therapy is associated with improved outcomes in this progressive multisystem disease. The diagnosis is usually delayed due to late presentation and nonspecific symptoms resulting in high morbidity and mortality. The incidence of MPSI in US is estimated to be 0.26:100,000, however, it is unknown in Kuwait. This pilot study was undertaken to screen MPSI in all Kuwaiti neonates born at Farwaniya Hospital over a period of 12-months. This study examined the incidence of MPSI in a major center in Kuwait for inclusion in the national newborn screening program to enable its early detection and adequate treatment. Methods: All Kuwaiti neonates born at Farwaniya Hospital, Kuwait from December 2021 to December 2022, were screened for MPSI. The screening consisted of determining IDUA enzyme activity in dried blood spots (DBS)-derived samples by Tandem Mass Spectrometry. A follow-up genetic analysis of IDUA gene is planned to screen the cases with diminished IDUA enzyme activity as second-tier testing. Results: A total of 618 newborns, including 331 (54%) males and 287 (46%) females, were screened. Twenty of them had deficient IDUA enzyme activity but showed negative genetic testing for IDUA. However, we have diagnosed one additional female baby with MPSI, who belonged to Farwaniya Hospital, but the parents chose to deliver in a private hospital. She presented at age three months with recurrent upper airway infections, snoring and extensive Mongolian spots. The molecular study revealed previously reported pathogenic nonsense variant in IDUA c.1882C>T; p.(Arg628Ter), associated with severe phenotype. That being included, MPSI is estimated to be about 0.3% among tested females and 0.2% of all screened cases in Kuwait. Conclusion: Our study is the first to evaluate the incidence of MPSI in Kuwait. Given the single center, small number of screened babies and the short study duration thus far, it is premature to calculate the incidence of MPSI. It is anticipated that as the study continues and more infants are examined, we would be able to estimate the incidence of this disease in our population correctly. Further studies including screening newborns in all maternity hospitals in Kuwait are needed to calculate the actual incidence of MPSI. Our data supports including MPSI in national newborn screening program to allow early initiation of treatment and thus improve disease outcome.

Burkina Faso is a sub-Saharan African country with a high poverty rate that has quadruplicated its population in the last half fifty years, that is, from 4.5 to 18 million inhabitants. Such demographic changes together with an intense migration process from rural areas to large cities, among other issues, are contributing to a rapid process of socio-cultural transformation. In this context, changes in both traditional and contemporary housing are analyzed and a complete ther-mo-hygrometric evaluation is carried out by processing significant data from on-site measure-ments to shed new light on the response of the said dwellings to the environmental and local cultural values. Results show that the introduction of land ownership linked to climate change and the increasing scarcity of natural resources are forcing native ethnic groups to modify their traditional ways of life, threatening their subsistence. Consequently, we can prove that the new building typologies are not in the least suitable for the climatic conditions nor the rich cultural heritage of Burkina Faso. This fact, negatively affects the possibility of revitalizing vernacular and environmentally-oriented solutions for the contemporary world and the necessary advance to-wards a more sustainable architecture.

Ante-mortem bovine tuberculosis (bTB) tests for buffaloes include the single comparative intradermal tuberculin test (SCITT), interferon-gamma (IFN-γ) release assay (IGRA) and IFN-γ-inducible protein 10 release assay (IPRA). Although parallel test interpretation increases detection of Mycobacterium bovis-infected buffaloes, these algorithms may not be suitable for screening buffaloes in historically bTB-free herds. In this study, the specificities of three assays were determined using M. bovis unexposed herds, and a high specificity diagnostic algorithm developed. Serial test interpretation using the IGRA and IPRA showed significantly greater specificity (98.3%) than individual tests or parallel testing (73%). When the SCITT was added, the algorithm had a 100% specificity. Since the cytokine assays had imperfect specificity, potential cross-reactivity with nontuberculous mycobacteria (NTM) was investigated. No association was found between NTM presence (in oronasal swab cultures) and positive cytokine assay results. As a proof-of-principle, serial testing was applied to high-value buffaloes (n=153) in a historically bTB-free herd. Buffaloes positive on a single test (n=28) were regarded as test negative. Four buffaloes were positive on IGRA and IPRA, and M. bovis infection was confirmed following culling. These results demonstrate the value of using IGRA and IPRA in series to screen buffalo herds with no previous history of M. bovis infection.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

Abstract: A prevalence boundary (PB) marks the point in prevalence where the false omission rate, RFO=FN/(TN+FN), exceeds the tolerance limit for missed diagnoses. Objectives were to mathematically analyze rapid antigen test (RAgT) performance, determine why PBs are breeched, and evaluate the merits of testing three times over five days, now required by the US Food and Drug Administration for asymptomatic persons. Equations were derived to compare test performance patterns, calculate PBs, and perform recursive computations. An independent July 2023 FDA-university-commercial evaluation of RAgTs provided performance data used in theoretical calculations. Tiered sensitivity/specificity comprise: Tier-1) 90%, 95%; Tier-2) 95%, 97.5%; and Tier-3) 100%, ≥99%, respectively. Repeating a T2 test improves the PB from 44.6% to 95.2% (RFO 5%). In the FDA-university-commercial evaluation, RAgTs generated sensitivity of 34.4%, which improved to 55.3% when repeated, then 68.5% with the third test. With RFO=5%, PBs were 7.37/10.46/14.22%, respectively. PB analysis suggests RAgTs should achieve clinically proven sensitivity of 91.0-91.4%. When prevalence exceeds PBs, missed diagnoses can perpetuate virus transmission. Repeating low-sensitivity RAgTs delays diagnosis. In homes, high-risk settings, and hotspots, PB breaches may prolong contagion, defeat mitigation, facilitate new variants, and transform outbreaks into endemic disease. Molecular diagnostics can help avoid these potential vicious cycles

With the continuous development of digital transformation and upgrading of Chinese construction enterprises, it is becoming increasingly important to measure their digital level, find the problems in the enterprise transformation process, and identify the key factors of enterprise digital capacity enhancement. This paper constructs a construction enterprise digital transformation maturity evaluation model from six first-level indicators and 20 second-level indicators, including digital strategy, digital business application, digital technology capability, data capability, digital organization capability, and change management. Digital maturity is divided into five levels: business management, process operation, intelligent construction, intelligent scene application, and industrial ecological collaboration. A detailed process of digital maturity evaluation based on the method of Analytic Hierarchy Process (AHP)-Decision Testing and Evaluation Laboratory (DEMATEL) is then developed. A questionnaire survey of 25 experts is used to weight the various parameters in the model, which is then demonstrated with an example construction enterprise. The model comprehensively reflects digital levels under the background of the digital economy. Its application will help understand the advantages and disadvantages enterprises face in their digital transformation to enable targeted measures to improve their digital transformation capabilities and efficiency, enhance their core competitiveness of enterprises, and promote the development of digital transformation in the construction industry.

For the soil in different regions, the nutrient fertility contained in it is different, and the detection and zoning management of soil nutrients before tillage every year can improve grain yield. In this paper, an integrated learning strategy model based on black soil hyperspectral data is designed for rapid classification of organic matter content classification of black soil. Soil hyperspectral image dataset of Xiangyang Experimental Base was collected; by changing the internal structure of the stacking model, an LSVM-stacking model with (MLP, SVC, DTree, XGBl, kNN) five classifiers as the L1 layer was built, and the simulated annealing algorithm was used for hyperparameter optimization. Compared to other stacking models, the LSVM-stacking metrics are significantly improved. The accuracy rate of hyperparameter optimization is improved by 38.6515%, the accuracy rate of the independent test data set is 0.9488, and the comparison of individual learners can improve the recognition classification accuracy of label"1" to 1.0.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

Background: The COVID-19 pandemic has promoted a shortage of filtering facepiece respirators (FFRs) and the emergence of new FFRs brands. We aimed to determine the fit provided by in-use FFRs in Peruvian healthcare workers (HCWs) during the COVID-19 pandemic. Methods: We enrolled 279 HCWs from 37 primary healthcare centers with highest burden of care for TB in Peru, of which 263 were assessed using quantitative fit tests (QNFT). Results were expressed as real-time fit factor (rt-FF) and overall fit factor (overall-FF), which was categorized as ≥100 (optimal result), 50-99, and <50. Results: We identified 3M 1860 FFRs (33.1%), Xiantao Zhong Yi ZYB-11 FFRs (24.7%) and Makrite 9500 FFRs (20.5%), mainly. Eighty-seven HCWs (33.1%) had an optimal overall-FF, 27 (10.3%) between 50-99, and 149 (56.7%) less than 50. Of the 87 HCWs with optimal over-all-FF, 73 (83.9%) were 3M 1860 FFR. Of the 27 participants with overall-FF between 50-99, 7 (25.9%) were Makrite 9500, while of the 149 with overall-FF less than 50, 58 (38.9%), and 47 (31.5%) were Xiantao Zhong Yi ZYB-11 and Makrite 9500, respectively. Conclusion: The Xiantao Zhong Yi and Makrite FFRs do not adapt adequately to the face of Peruvian HCWs, most having fit factors less than 50.

(1) Background: The COVID-19 pandemic had a devastating impact on the world, causing widespread illness and death. It is essential to focus on prevention strategies to limit the spread of the disease. Despite the advent of vaccines, maintaining a vigilant approach to prevention remains paramount. While vaccines are essential, they do not guarantee absolute immunity, and their protective effect may diminish over time; (2) Methods: We reviewed effective strategies to prevent COVID-19 transmission. We focused on me-ta-analyses (MA), literature reviews (LR) and the health care context. Various prevention measures and interventions were reviewed. Both es-tablished practices and unresolved issues were considered; (3) Results: Standard precautions (SP) as the cornerstone of infection control, with hand hygiene and mask use as key components. Debate about the relative importance of droplet versus aerosol transmission led to differences in recommendations between agencies at the onset of the pandemic. We have clarified the role of personal protective equipment (PPE), including eye protection. The effectiveness of masks in pre-venting transmission is reviewed. The use of surgical masks is recommended to prevent droplet transmission, while eye protection is recommended in combination with masks. Although data show some risk reduction, the clear superiority of N95/FFP2 over surgical masks remains unproven. In terms of room occupancy, ventilation is critical in reducing the risk of transmission in poorly ventilated environments. The use of negative pressure isolation rooms (NPIRs) is being investigated. The presence of viral RNA on surfaces does not necessarily indicate infectivity, and the risk of transmission by surface contact is low if surfaces are properly maintained and hand hygiene is practised regularly. Testing for SARS-CoV-2 in asymptomatic persons in healthcare settings may help prevent transmission; (4) Conclusions: Prevention of SARS-CoV-2 transmission requires a multifaceted approach, including reducing particle emissions from infected persons by wearing masks, eliminating aerosols by ventilation, ensuring physical separation, and protecting exposed persons with masks and eye protection.

Background: Multiple system atrophy (MSA) is a rapidly progressive neurodegenerative disorder that has no curative treatment. Diagnosis is based on a set of criteria established by Gilman (1998 and 2008) and recently updated by Wenning (2022). We aim to determine the effectiveness of [123I]Ioflupane SPECT in MSA, especially at the initial clinical suspicion. Methods: Cross-sectional study of patients at initial clinical suspicion of MSA, referred for [123I]Ioflupane SPECT. Results: 139 patients (68 men, 71 women) were included, 104 being MSA-probable and 35 MSA-possible. MRI was normal in 89.2% while SPECT was positive in 78.45%. SPECT showed high sensitivity (82.46%) and positive predictive value (86.24), reaching maximum sensitivity in MSA-P (97.26%). Significant differences were found when relating both SPECT assessments in the healthy-sick and inconclusive-sick groups. We also found an association when relating SPECT to the subtype (MSA-C or MSA-P), as well as to the presence of parkinsonian symptoms. Lateralization of striatal involvement was detected (left side). Conclusions: [123I]Ioflupane SPECT is a useful and reliable tool for diagnosing MSA, with good effectiveness and accuracy. Qualitative assessment shows a clear superiority when distinguishing between the healthy-sick categories, as well as between the parkinsonian (MSA-P) and cerebellar (MSA-C) subtypes at initial clinical suspicion.

The seed industry plays a crucial role in the global food production, but it faces a persistent challenge in ensuring the health and quality of seeds, particularly those of tomato and pepper, which represent key seed commodities on the global market. Seeds can serve as potential pathways for the introduction and dissemination of seed-borne bacteria, which may have devastating effects on crop yield, farmers’ remunerability, and food security. Therefore, fungicides and other anti-microbial compounds are extensively used to disinfect the seeds, thus increasing the input of chemicals in the agri-enviroment. In this review, we address aspects that connect disease epide-miology with seed infection and health, including seed contamination, endophytic colonization, and seed-borne infections. We focused on the main bacterial diseases affecting tomato and pepper by discussing their official seed testing methods as requirements supporting a smooth seed trade. Moreover, we present a survey on the past and recent innovations for seed treatments, focusing on sustainable disinfection methods. Therefore, this review will be a short, but indispensable guide for seed technologists and pathologists involved in the production of high-quality seeds, providing indications and suggestions to contrast seed-borne pathogens dissemination, avoid international controversies and complaints by phytosanitary authorities, extension services and farmers.