This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

In the food industry, Listeria is a standard control microorganism in ready-to-eat food since it may be pathogenic and cause a disease called listeriosis. The objective of the present study was to carry out a challenge test to verify the efficiency of different combinations of natural antimicrobial ingredients, against Listeria monocytogenes, to be used in ready-to-eat foods. Six different formulations of cooked ham were elaborated: a control, and five different formulations. An initial inoculation of 2 log cycles was used in the different products and the growth of Listeria was monitored at different temperatures and times (4° C for 17 w; 7ºC for 12 w). Control samples showed a progressive growth, reaching 5-6 log after 3 or 4 weeks. The rest of samples showed constant counts of Listeria during the all study. Only samples containing: 100 ppm nitrite + 250 PPM ascorbic acid+0,7% PRS DV-5 did not control the growth of Listeria at 7 ° C after 7 w of storage. The results obtained allowed to classified the cooked ham elaborated using any natural ingredients combinations as a “Ready-to-eat food unable to support the growth of L. monocytogenes other than those intended for infants and for special medical purposes”.

Most diagnostic tests for tuberculosis (TB) rely on sputum samples, which are difficult to obtain and have low sensitivity in immunocompromised patients, patients with disseminated TB, and children, delaying treatment initiation. The World Health Organization (WHO) calls for the development of a rapid, biomarker-based, non-sputum test capable of detecting all forms of TB at the point-of-care to enable immediate treatment initiation. Lipoarabinomannan (LAM) is the only WHO-endorsed TB biomarker which can be detected in urine, an easily collected sample. This review discusses the characteristics of LAM as a biomarker, describes the performance of first-generation urine LAM tests and reasons for slow uptake, and presents considerations for developing the next-generation of more sensitive and impactful tests. Next-generation urine LAM tests have the potential to reach adult and pediatric patients regardless of HIV status or site of infection and facilitate global TB control. Implementation and scale-up of existing LAM tests and development of next-generation assays should be prioritized.

Oriented strand board (OSB) panels are widely marketed for several applications, from building to packaging. The manufacturing of poplar OSB started recently in Northern Italy representing a relevant innovation in the sector since this product is usually made of coniferous wood. The thermal treatment is widely used for reducing the hygroscopicity of wood-based products, nonetheless it influences the mechanical behavior and degrades the main components of wood, which can affect their finishing. Therefore, it is important to know the properties of the treated surfaces. To this purpose, in this study a lot of OSB panels, made of poplar wood, 15 mm thick and with a density of 590 kg/m³, were thermally treated under vacuum conditions at 190 °C for 2 h and then subjected to accelerated weathering. The changes in color and in wettability due to treatment and accelerated weathering were studied. The thermal treatment determined a significant darkening of the color; the accelerated weathering darkened the untreated surfaces and, on the opposite, lightened the thermo-treated surfaces. The wettability decreased after thermal treatment and increased after weathering, more evidently in treated panels. Overall, this study improves the knowledge about the behavior of the surface of thermo-treated poplar OSB, which is relevant for the industrial coating of this product.

Hair cosmetics are in fashion. Numerous products are commonly used in combination. Frequent allergens are present in hair cosmetics, which, added to almost daily use, increase the risk of sensitization. Familiarity with the clinical distribution of the eczematous rash is necessary to seriously consider patch testing. There are haptens on the market, although not all of them. It is necessary to know how to patch your own products. When avoidance of the allergen cannot be possible, new treatments are being evaluated to combat allergic contact dermatitis, mainly of the occupational type. In this manuscript, a complete and practical review of the main allergens and contact sources of hair cosmetic origin has been carried out.

Acceleration parameters in sit-to-stand (STS) movements are useful for measuring lower-limb function in older adults. The purpose of this study was to examine the relationship between acceleration in STS movements and physical function and the test-retest reliability of acceleration parameters in older adults. We performed cross-sectional analyses on 244 older adults including 107 men (mean age:77.4±4.7) and 137 women (mean age: 75.6±5.3). Four acceleration parameters were measured in STS movements: maximum acceleration (MA), maximum velocity (MV), maximum power (MP), and stand-up time (ST). Good intraclass correlation coefficients (ICC>0.70) were observed for all parameters. For the acceleration parameters, MA, MV, and MP were relatively strongly associated with the 5-time STS test (men: r=-0.36~-0.47; women: r=-0.37~-0.45) and the Timed up and Go test (men: r=-0.39~0.47, women: r=-0.43~-0.51): MP was also strongly associated with grip strength (men: r=0.48, women: r=0.43). All acceleration parameters were poorer in participants reporting mobility limitations than in those reporting no mobility limitations. These findings support the usefulness of sensor-based STS measurement. The system is expected to be useful in various settings where care prevention is addressed.

Introduction:Few robust studies have analyzed association between cognitive tests and the marital status of Mild Cognitive Impairment (MCI) group with ADNI dataset. To test the hypothesis that Rey Auditory Verbal Learning test (RAVLT) cognition performance with marital status is associated with greater odds of MCI group than either RAVLT independently, we used TADPOLE data to evaluate cross-sectional associations between RAVLT performance in immediate response, learning, forgetting, and perception of forgetting with marital status and MCI. Methods: Subjects with MCI and Normal Cognition were included. Logistic regression models indicate associations between four RAVLT subgroups (low and high performance of immediate response, immediate response with learning, performance of immediate response with learning and forgetting, performance of immediate response with learning, forgetting and perception of forgetting) and MCI group. Models adjust for age, sex, race, marital status, ethnicity, education, APOE4 genotype, hippocampus, whole-brain, ventricles and ICV. Results: The sample (n=6560) had a mean age of 77 / 67 years, 44% were female, 58% in MCI group. Only all RAVLT subgroups test with age 61 to 70(OR 0.26, 95% CI 0.15-0.45), age 71 or older(OR 0.07, 95% CI,0.04-0.12), race:black/african american(OR 0.13, 95% CI 0.03-0.52)race:more than one(OR 0.05, 95% CI 0.01-0.24), marital status:never married(OR 0.2, 95% CI 0.12-0.34). Conclusion: Studies are needed to evaluate other cognitive test with missing data within TADPOLE dataset as modifiable risk factor for MCI.

In this study a method for predicting the preferred pleasantness induced by different forest environments, represented by virtual photographs, was proposed and evaluated using a novel Anti-Environmental Forest Experience Scale psychometric test. The evaluation questionnaire contained twenty-one items divided into four different subscales. The factor structure was assessed in two separate samples collected online (sample 1: N = 254, sample 2: N = 280). The internal validity of the four subscales was confirmed using an exploratory factor analysis. Discriminant validity was tested and confirmed using the Amoebic Self Scale (Spatial-Symbolic domain). Concurrent validity was confirmed using the Connectedness to Nature Scale. Predictive validity was based on assessment of pleasantness induced by nine different photographs (control – urban landscapes, forest landscapes, dense forest landscapes), with subscales differently correlated with the level of pleasantness assessed for each photograph. This evaluation instrument is appropriate for predicting preferred pleasantness induced by different forest environments.

Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

In order to reduce the vibration of the transporter and improve the stability of the transporter, the vibration characteristics and key structure optimization research of the mountain orchard transporter are carried out. In this paper, the vibration of electric monorail transporters under different working conditions is tested, and the causes of vibration generated by monorail transporter during operation are explored. The three-dimensional model of the trailer and transmission box is established using Solidworks, and the modal vibration modes of the structure are analyzed theoretically. The modal test system is used for modal test analysis of trailers and transmission boxes. By comparing the results of finite element and experimental modal analysis, the second-order frequency of the trailer is close to the motor's rotating excitation frequency of 50 Hz at rated speed, which is easy to generate resonance. By optimizing the structure of the trailer, the second and third natural frequencies are increased to 54.79 Hz and 58.35 Hz respectively, which avoid the resonance of the trailer during operation and effectively reduce the vibration generated during the transportation of the trailer. Through vibration testing of the optimized electric monorail transporter, the results of vibration testing before and after structural optimization are compared and analyzed, and it is found that the vibration amplitudes of the transporter in X, Y and Z directions are reduced by 0.308m/s², 0.351m/s² and 0.334m/s² respectively, the running stability of the conveyer is improved.

Background: Open AI developed ChatGPT, a language model based on the GPT architecture, designed for text-based communication. Trained on diverse internet texts, ChatGPT generates contextually appropriate responses using machine learning. It understands input through analysis and context interpretation, generating coherent and contextually relevant responses. Interaction is possible through messaging platforms. Materials and Methods: In November 2023, we utilized ChatGPT 3.5, the default version at that time, to answer questions from the Italian National Residency Program Admission Tests (SSMs) of 2021, 2022, and 2023. The questions cover clinical, diagnostic, analytical, therapeutic, and epidemiological scenarios, sometimes accompanied by images. The study compared ChatGPT's answers to the official corrections on the Italian Ministry of University and Research (MUR) website. The scoring method used for evaluation was 1 point for correct answers, 0 points for unanswered questions, and -0.25 points for incorrect answers, reflecting the SSM test scoring system. Results: In summary, ChatGPT was tested with a total of 420 questions, 140 for each test. It achieved an overall accuracy of 80.48%, providing correct answers for 338 questions and incorrect answers for 82 questions. When faced with questions containing both text and images, it answered 55% correctly and 45% incorrectly. The model's performance varied over time, with an 82.14% accuracy rate in 2021 and 2022 (115 correct out of 140) and a 77.14% accuracy rate in 2023 (108 correct out of 140). Applying thisscoring method to the SSM test, ChatGPT would have scored 105 points in 2021 and 2022, and 100 points in 2023. Conclusions: ChatGPT has exhibited above-average performance in the last three SSM tests, highlighting its robust capability to interpret clinical scenarios and offer precise diagnostic and therapeutic guidance. Despite this, some limitations persist, notably the software's inability to interpret non-textual information.

Nowadays, the presence of pathogen-specific antibodies in the blood is widely controlled by a serodiagnostic technique based on the lateral flow immunoassay (LFIA). However, its common one-stage format with an antigen immobilized in the binding zone of a test strip and a nanodis-persed label conjugated with immunoglobulin-binding proteins is associated with risks of very low analytical signals. It is caused by the presence of non-specific immunoglobulins in very large excess to the target antibodies in the tested samples thus decreasing their binding with the detected labels. In this study, the first stage of the immunochromatographic serodiagnosis was carried out in its traditional format using a conjugate of gold nanoparticles with staphylococcal immunoglobulin-binding protein A and an antigen immobilized on a working membrane. At the second stage, a labeled immunoglobulin-binding protein was added, which enhanced the coloration of the bound immune complexes. The use of two separated steps, binding of specific antibodies, and further coloration of the formed complexes allowed a significant reducing the influence of non-specific immunoglobulins on the assay results. The proposed approach was ap-plied for the serodiagnosis using a recombinant RBD protein of SARS-CoV-2. As a result, an in-crease in the intensity of test zone coloration by more than two orders of magnitude was demonstrated, which enabled to significantly reduce false-negative results. When testing a panel of 16 positive and 8 negative serum samples, the diagnostic sensitivity of the LFIA was 62.5% for the common format and 100% for the enhanced format; the diagnostic specificity of both variants was 100%.

Managing blood cholesterol levels is important for the treatment and prevention of diabetes, cardiovascular disease, and obesity. An easy-to-use, portable cholesterol blood test will accelerate more frequent testing by patients and at-risk populations. We aim to evaluate the performance of smartphone-based point-of-care cholesterol blood tests as compared to that of hospital-grade laboratory tests. We used smartphone systems that are already familiar to many people. Because smartphone systems can be carried around everywhere, blood can be measured easily and frequently. We compared the results of cholesterol tests with those of existing clinical diagnostic laboratory methods. We found that smartphone-based point-of-care lipid blood tests are as accurate as hospital-grade laboratory tests (N=116, R>0.97, P<0.001 for all 3 cholesterol blood tests: total cholesterol, high density lipoprotein, and triglyceride). Our system will be useful for those who need to manage blood cholesterol levels to motivate them to track and control their behavior.

Stock bubbles are characterized by unpredictable price surges and subsequent declines, causing significant losses for investors. The study aimed to detect mildly explosive patterns in S&P 500-listed stocks in real-time using the GSADF test. This study focused on the length, the normality of the stock bubble episode and compared the effectiveness of SADF and GSADF tests in bubble detection, consistently finding GSADF's superiority. The duration of breakouts exhibited non-normality, suggesting unusually long bubble durations.

Wave overtopping, i.e., excess of water over the crest of a coastal protection infrastructure due to wave run-up, of a smooth slope can be reduced by introducing slope roughness. A stepped revetment ideally constitutes a slope with uniform roughness. Apart from reducing overtopping, a stepped revetment provides safer access to a beach compared to conventional rubble. In recent years, research studies on stepped revetments have provided valuable findings regarding the performance and design optimization of stepped revetments as a typical mean of coastal protection. A stepped revetment can reduce overtopping volumes of breaking waves up to compared to a smooth slope. The effectiveness of the overtopping reduction decreases with increasing Iribarren number. However, up to date a unique approach applicable for a wide range of boundary conditions is still missing. The present paper critically reviews previous findings, gathers and analyzes data from previous studies and proposes a new formula for robust prediction of overtopping of stepped revetments. By means of this approach a critical assessment based on beforehand disclosed parameter ranges between a smooth slope on the one hand and a plain vertical wall on the other are contrasted. By analysis of a new data set compounded from different original studies a novel empirical formulation is derived to predict the roughness reduction coefficient of a stepped revetment for breaking and non-breaking waves. This coefficient is developed and adjusted for a direct incorporation into the present design guidelines. Underlying uncertainties are clearly addressed and quantified. Scale effects are highlighted.

Hepatitis B e antigen (HBeAg) is a marker of wild-type hepatitis B virus replication. In resource-limited countries where access to enzyme-linked immunosorbent assay (ELISA) remains a challenge, rapid diagnostic tests (RDT) constitute a good alternative. The HBeAg status is employed to evaluate eligibility for antiviral therapy and to prevent the transmission of hepatitis B from mother to child (PMTCT). The objective of this study was to assess the diagnostic performance of the SD-Bioline®HBeAg RDT commonly used for detecting HBeAg in laboratories in Burkina Faso. The sample panel used was collected from HBsAg positive patients received in the laboratory for the detection of HBeAg with the rapid test. The samples were retested for HBeAg using the VIDAS HBe/Anti-HBe enzyme-linked fluorescent assay (ELFA) (Gold standard). Then, the viral load (VL) of HBV DNA was determined using the GENERIC HBV CHARGE VIRLAE kit (GHBV-CV). The diagnostic performances of the SD-Bioline®HBeAg and its agreement with the gold standard were calculated with their 95% confidence intervals. 340 sera obtained from HBsAg positive patients were included in this evaluation Compared to the VIDAS HBe/Anti-HBe ELFA test, the sensitivity (Se) and specificity (Sp) of the SD-Bioline®HBeAg test were 33.3% and 97.9% respectively. The concordance between the two tests was 0.42. Depending on the viral load, the Se and Sp varied from 8.8% and 98.3% for a VL &lt; 2,000 IU/mL to 35.5% and 98.4% for a VL &gt; 2,000,000 IU/mL. The results showed a low Sensibility of the SD-Bioline®HBeAg RDT test, indicating that its use is inappropriate for the clinical management of HBV-infected patients. They also highlight the urgent need to develop HBeAg rapid tests with better sensitivities.

The aim of this study was to clarify effects of 3-week work-matched high-intensity intermittent cycling training (HIICT) with different cadences on VO2max in university athletes. Eighteen university athletes performed HIICT with either 60 rpm (n = 9) or 120 rpm (n = 9). HIICT consisted of eight sets of 20-s exercise with a 10-s passive rest between each sets. The initial training intensity was set at 135% of VO2 max and was decreased by 5% every two sets. Athletes in both groups performed 9 sessions of HIICT during 3-week. The total work-load and achievement rate of the work load calculated before experiments in each group were used for analysis. VO2max was measured pre and post-training. After 3-week of training, no significant differences in the total work-load and achievement rate of the work load were found between the two groups. VO2max similarly increased in both groups from pre to post training (p = 0.016), with no significant differences between the groups (p = 0.680). These results suggest that cadence during HIICT is not training variable affecting effect of VO2max.

Over the last ten years, the integrated pond aquaculture (IPA) has been developing rapidly as a new aquaculture mode, and mechanical power oxygenator is a common oxygenation device in this aquaculture mode. However, with the gradual expansion of the application range of this aquaculture mode, the problems of low efficiency, poor oxygenation uniformity, and low applicability of mechanical power oxygenators, which can produce water reflux and suction pollution accumulation, have gradually emerged. Therefore, we designed a new type of push-water aerator device (NPWAD) applicable to the integrated recirculating water aquaculture mode of ponds. Mainly, the specific parameters of the key components were clarified through the selection calculation and structural design, and the experiments were carried out in the self-constructed pond integrated aquaculture system at the experimental base. The experiments were carried out on the water in the tank for grass carp culture, and the oxygenation and water pushing effects of the type of push-water aerator device under 15 groups of different operating parameters were carried out by using multiple types of high-precision water quality monitoring sensors, with the rotational speed of the device, the operating time (0-30 min) and the height of the water (0.5-1.5 m) as the independent variables, and the oxygenation amount R, the oxygenation power efficiency E_s and the surface layer of the water as the evaluation indexes, average flow velocity V_f were used as its evaluation indexes of oxygenation and water pushing. The results show that the optimal parameters of the NPWAD are impeller water lifting component speed n_1=1000r/min, small-hole aeration component speed n_2=2280r/min. At this time, the average oxygen increase of this device is R=1.96mg/L, the average oxygenation power efficiency is E_s=3.8 kg·(h·kW)-1, the DO uniformity of the water M_1=95.3%, and the average flow velocity V_f=190.8mm/s, which can effectively promote the water directional flow and achieve the water circulation and layer exchange, and it is in line with the preferred swimming speed of grass carp at various growth stages. The new type of push-water aerator device is able to enhance the DO concentration of the water faster, but also to achieve the purpose of promoting the directional flow of the water and renewing the water in the tank, as well as in a short period of time to improve the uniformity of the DO of the water faster, for the improvement of the pond aquaculture production efficiency has practical significance.

This paper reports the effect of as-deposited surface condition on the fatigue strength in an additive manufactured titanium alloy Ti-6Al-4V (WAAM Ti64). First, local stress concentration caused by the surface waviness was quantified by a metrology technique followed by numerical modelling. Fatigue tests were conducted under bending load with the as-deposited surface being under tensile cyclic stress. The applicability of two predictive methods was studied and compared with the fatigue test results. The traditional notch stress method overestimated the fatigue strength by a factor of 1.5 at a given life; the poor agreement with the test is attributed to the crack propagation from the waviness being dominant in the bending test, i.e., the crack initiation stage was short, hence the local stress method is unsuitable. The fracture mechanics approach has delivered good predictions at every applied stress levels. The method treats a waviness trough as an initial crack. This approach is suitable for predicting the fatigue life in materials built by wire based directed energy deposition processes.

A cross-sectional study was carried out to determine the prevalence of subclinical mastitis (SCM) among medium to large scale household dairy farms in southwestern district, Jhenaidah, Bangladesh during July to December 2019. A total of 78 (n=100) lactating cows from household dairy farms (N=32) having three or more dairy cows were selected randomly as sampled populations. Milk samples were screened for SCM by using Surf Field Mastitis Test (SFMT). The prevalence of SCM varied among farm level [71.9% (95% CI: 53.3-86.3)], individual animal level [67.9% (95% CI: 56.4-86.3)] and quarter level [29.5% (95% CI: 24.5-34.9)]. Descriptive statistics represented the farmers and farm demography, characteristics of the sampled population, and overall management feature. Random Effect Logistic Regression identified, Body Condition Score (BCS) [OR=3.8 and 2.9, at cows level and quarter level respectively (BCS-2 vs. BCS-≥3)], and breed [OR=5.1 and 2.9, at cows level and quarter level respectively (HF× Sahiwal vs. HF × Local)] as potential risk factors. This study shows that SCM is highly prevalent in the study area, which is a major threat to the dairy industry's production performance. Regular screening by SFMT, proper hygiene, improve the management system, and farmer’s awareness is required to control the disease.

Depression and cognitive impairment are recognized complications of COVID-19. This study aimed to assess cognitive performance in clinically diagnosed post-COVID depression (PCD) patients using neuropsychological testing. The study involved 71 post-COVID patients, with matched control groups: recovered COVID-19 individuals without complications (n=18) and individuals without prior COVID-19 history (n=19). A post-COVID depression group (PCD, n=25) was identified based on psychiatric diagnosis, a comparison group (noPCD, n=46) included participants with neurological COVID-19 complications, excluding clinical depression. The PCD patients showed significantly less scores in the MoCA test, decreased immediate memory recall in the Word Memory Test, decreased processing speed and higher accuracy in the Trail Making Test, and near to significant worse executive control and processing speed in the Stroop task compared to controls and the noPCD patients. The number of post-COVID symptoms negatively correlated with immediate word memory recall and processing speed among all post-COVID patients. In PCD patients, negative correlations between number of post-COVID symptoms and delayed recall, between time after recovery and immediate recall, and positive correlation between the number of acute symptoms and processing speed in the incongruent condition of the Stroop task were found. No differences between groups in Sniffin’s stick olfactory test was found. Overall, our study revealed cognitive impairment in PCD patients similar to those in major depressive disorder.

Several factors, such as internal algorithm, sensor technology, and obsolescence might skew outcomes when comparing different gas analysers measurements during CPET. Besides aerosol borne infectious disease are a source of contamination during cardiopulmonary exercise tests (CPET). Thus, the main aim of this study was to determine the agreement degree between the Quark RMR and the Jaeger Oxycon Pro, using an antibacterial filter with the latter. Forty-two participants (19-54 years old) performed two non-consecutive maximal graded exercise tests on a cycle-ergometer on two counterbalance and different days using the Oxycon Pro and the Quark RMR in a randomized order. Differences between devices were tested using a generalized linear model adjusted by Bonferroni, and correlation and agreement was assessed using Pearson’s correlation coefficient (R), intraclass coefficient correlation (ICC), Lin’s concordance correlation coefficient (CCC) and Bland-Altman plots. No significant differences were found between devices in any of metabolic or ventilatory parameters for cardiorespiratory fitness assessment (VO_2max: 3131.3±882.1 vs. 3189.8±894.8, p=0.071, VCO_2max: 3436.3±936.0 vs. 3550.3±1043.2, p=0.071, for Quark RMR and Oxycon Pro, respectively). However, Bland-Altman plots showed a trivial tendency towards Oxycon Pro overestimation relative to Quark RMR as air flow volume increases. Both devices showed strong correlation and high level of agreement during maximal and submaximal exercise intensities (Pearson’s R: 0.974 & 0.977; ICC: 0.985 & 0.987; Lin’s CCC: 0.971 & 0.974, for VO₂ and VCO₂, respectively). Therefore, providing consistency to CPET data comparison between both devices, and insight into whether the use of these metabolic carts could be interchangeable or combined when a single device cannot be used for CPET assessment.

Introduction: The SARS-CoV2 pandemic has led to an worldwide shortage of Personal Protection Devices (PPD) for medical and paramedical personnel. Adaptation of commercially available snorkel masks to serve as full face masks has been proposed. Even not formally approved as PPD, they are publicized on social media as suitable for this use. Concerns about actual protection levels and risk of carbon dioxide (CO₂) accumulation while wearing them for extended periods made us perform a systematic testing of various brands, in order to verify whether they are as safe and effective as claimed. Methods: A ‘fit’ test was performed, analogous to gas mask testing. Respiratory safety was evaluated by measuring end-tidal CO₂ and oxygen saturation while wearing the masks in rest and during physical exercise. Masks were tested with 3D adaptors to mount regular bacterial-viral ventilator filters when available, or with snorkel openings covered with N95/FFP2 cloth. Results: Modified masks performed reasonably well on the fit test, comparable to regular N95/FFP2 masks. Not all ventilator filters are equally protective. For all masks, a small initial increase in end-tidal CO₂ was noted, remaining within physiological limits. Masks with specific adaptors (3D printed or provided by the manufacturer) are safer, have more flexibility and reliability than makeshift adaptations. Conclusions: These masks can offer benefit as a substitute for complete protective gear as they are easier to don and remove and offer full-face protection. They may be more comfortable to wear for extended periods. Proper selection of mask size, fit testing, quality of 3D printed parts and choice of filter are important.

A patient will visit physicians when he/she feels ill. This illness is not for COVID-19 but it is a general tendency of human being to visit doctor probably it can not be controlled by general drug. When a patient comes to a doctor, the doctor examines him/her after knowing his/her problem. The physician always asks him/her about some questions related to him/her daily life. For example, if a young male patient comes to a doctor with a symptom of fever and cough, the first question doctor asked him that he has a habit of smoking. Then doctor asks him whether this type of symptom appeared often to him previously or not. If the answers of both questions are yes, then the first one is habit and the second one is that he may suffering from some serious disease or a disease due to the weather. The aim of this paper is to consider habit of the patient as well as he/she has been affected by a critical disease. This information is used to build a model that will predict whether there is any possibility of his/her being affected by COVID-19. This research work contributes to tackle the pandemic situation occurred due to Corona Virus Infectious Disease, 2019 (Covid-19). Outbreak of this disease happens based on numerous factors such as past health records and habits of patients. Health records include diabetes tendency, cardiovascular disease existence, pregnancy, asthma, hypertension, pneumonia; chronic renal disease may contribute to this disease occurrence. Past lifestyles such as tobacco, alcohol consumption may be analyzed. A deep learning based framework is investigated to verify the relationship between past health records, habits of patients and covid-19 occurrence. A stacked Gated Recurrent Unit (GRU) based model is proposed in this paper that identifies whether a patient can be infected by this disease or not. The proposed predictive system is compared against existing benchmark Machine Learning classifiers such as Support Vector Machine (SVM) and Decision Tree (DT).

As time continues to advance, the need for robust security threat mitigation has become increasingly vital in software. However, ensuring early effective security threat mitigation requires optimal test data and consistent test case design. It is a constant struggle to maximize test coverage through test data optimization. We conducted explanatory research to maximize test coverage of security requirements as modeled in Structured Misuse Case Description (SMCD) i.e., structured specification of misuse case, so as to improve consistency in optimal test data generation. We specified constraints upon Mal activity in Object Constraint Language (OCL) in order to minimize human dependency and improve consistency in optimal test data generation. It was evident through results that MC/DC generated optimal test data of security threats through SMCD in comparison to the Decision Coverage method thus resulting in designing a significantly lower number of test cases and yet maximizing test coverage of security threats. MC/DC generated test data with n+1, while Decision Coverage generated test data with〖 2〗^n, we, therefore, conclude that MC/DC maximizes test coverage through optimal test data from SMCD in comparison to Decision Coverage.

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

Purpose: To investigate trabeculopuncture (TP) for predicting the outcome of ab interno trabeculectomy (AIT). AIT is an effective, low-risk procedure for open angle glaucoma. Despite widespread utilization, it fails in patients with an unidentified distal outflow resistance. Methods: We bisected 81 enucleated porcine eyes and perfused them for 72 hours. They were assigned to two groups: trial (n=42) and control (n=39). Intraocular pressure (IOP) was measured continuously. At 24 hours, four YAG-laser trabeculopunctures on the nasal trabecular meshwork were performed, followed by a 180° AIT at the same site at 48 hours. Eyes were divided into TP and AIT responders and non-responders; the proportion of TP responders between both AIT groups was compared. Results: Both post-TP and post-AIT IOPs were lower than baseline IOP (p=0.015 and p<0.01, respectively). The success rates of TP and AIT were 69% and 85.7%, respectively. The proportion of TP responders among AIT responders was greater than that of AIT non-responders (p<0.01). Sensitivity and specificity values of TP as predictive test for AIT success were 77.7% and 83.3%, respectively. The positive and negative predictive values were 96.6% and 38.5%, respectively. Conclusion: A 10% reduction in IOP after TP can be used as predictor for the success (>20% IOP decrease) of 180° AIT in porcine eyes.

There is still a lack of a clinical test to reliably identify patients with Parkinson’s disease (PD) being at risk for aspiration. In this prospective, controlled, cross-sectional study we assessed if swallowing speed for water is a useful clinical test to predict aspiration proven by flexible endoscopic evaluation of swallowing (FEES). Due to this we measured the swallowing speed for 90 ml water in 115 consecutive and unselected PD outpatients of all clinical stages and 32 healthy controls. Average swallowing speed was lower in patients compared with controls (6.5 ± 3.9 ml/s vs. 8.5 ± 3.2 ml/s; p < 0.01). The disease-independent widely used threshold of < 10 ml/s showed insufficient sensitivity of 88% and specificity of 19% with unacceptable false-positive rates of 63% for patients and 69% for controls. Receiver operating characteristic (ROC) analysis was carried out to define a suitable cut-off value for detection of aspiration of water (area under the curve 0.72, p < 0.001) in PD patients. The optimized cut-off value was 5.5 ml/s with a sensitivity of 69% and a specificity of 64%. Overall, measuring swallowing speed is prone to methodological errors and not suitable as a screening instrument to predict aspiration in PD patients.

There are some limitations in the null test measurement in the stitching interferometry. In order to meet the null test conditions, the moving distance between the sub-apertures often deviates from the theoretical preset distance, which leads to a position deviation of sub-apertures under measurements. To overcome this problem, an algorithm for data processing is proposed. We used iterative calculation of the deviations between the sub-apertures to adjust their positions, to ensure the local validity of the linear approximation algorithm and realize the exact stitching. A cylindrical lens as an object for experimental examination of the proposed method was taken. The obtained results demonstrate the validity, reliability and feasibility of our iterative stitching algorithm.

Alkali-silica reactivity (ASR) is one of multiple reactions responsible for premature loss in concrete infrastructure service life. ASR is a deleterious reaction initiated when highly reactive silicious content of aggregates reacts with alkali hydroxides content within portland cement in the presence of moisture. ASR results in the formation of expansive, white-colored gel-like material which results in internal stresses within hardened concrete. ASR induced stresses result in concrete cracking, spalling, and increased reinforcement steel corrosion rates. The main objective of this research is to improve the conditions of concrete infrastructure projects conditions by mitigating ASR damaging effect. The expansion of accelerated mortar bars poured using fine aggregates collected from different sources is measured versus time to evaluate aggregate’s reactivity. Different percentages of supplementary cementitious materials (SCMs) including class c fly ash, micro-silica, were used in remixing mortar bars to evaluate the efficiency of different types of SCMs in mitigating mortar bar expansion. Research findings showed that SCMs can mitigate ASR, thus, decrease the mortar bar expansion. The efficiency of SCMs in ASR mitigation is highly dependent on the incorporated SCM percentage and particle fineness. Silica fume, having the least particle size, displayed higher rates of ASR mitigation followed by fly ash, respectively. The outcomes of this research will assist design engineers in avoiding future losses due to ASR cracking in concrete infrastructure projects, and reduce the excessive need to maintenance, repair, and replacement activities.

Objective: The future mobility challenges leads to considering new safety systems to protect vehicle passengers in non-standard and complex seating configurations. The objective of this study is to assess the performance of a brand new safety system called nanobag and to compare it to the traditional airbag performance in the frontal sled test scenario. Methods: The nanobag technology is assessed in the frontal crash test scenario and compared with the standard airbag by numerical simulation. The previously identified material model is used to assemble the nanobag numerical model. The paper exploits an existing validated human body model to assess the performance of the nanobag safety system. Using both the new nanobag and the standard airbag, the sled test numerical simulations with the variation of human bodies are performed in 30 km/h and 50 km/h frontal impacts. Results: The sled test results for both the nanobag and the standard airbag based on injury criteria shows a good and acceptable performance of the nanobag safety system compared to the traditional airbag. Conclusion: The results show that the nanobag system has its performance compared to the standard airbag, which means that thanks to the design, the nanobag safety system has a high potential and extended application for multi-directional protection against impact.

Research has been actively conducted on the materials used to commercialize finished products that use hydrogen energy. Hydrogen embrittlement that occurs when hydrogen atoms penetrate metals is the largest problem that must be addressed first regarding safety. Because liquefied hydrogen has an 800 times higher density than hydrogen gas, hydrogen has been stored and transported through liquefaction at -253℃ using helium gas as a refrigerant. However, even if extreme temperatures below zero are maintained, natural vaporization loss that reduces liquefied hydrogen by 3 to 5% of the tank storage capacity per day occurs. In addition, when liquefied hydrogen is converted into high-pressure hydrogen gas for use, it is difficult to completely prevent the loss of the gas, even if sealing technology is applied to prevent gas leaks in transport and storage tanks. Therefore, methods to minimize the loss of hydrogen, establishment of assessment criteria for the embrittlement caused by a small amount of hydrogen gas, and related research are essential. We researched the hydrogen embrittlement resistance of SUS316L rods according to the tensile speed by conducting water electrolysis testing at room temperature, at which hydrogen gas is used to present hydrogen embrittlement assessment criteria for primary ring-shaped forged products.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

Tumors of the central nervous system produce adverse outcomes in everyday life; however, low-grade gliomas are uncommon in adults. For this reason, the objective is to describe the executive function of a 59-year-old adult neuro-oncological patient. Pre- and postintervention evaluation of neurological and neuropsychological functioning was performed through neuroimaging techniques (iRM, Spectroscopy, Electroencephalography), hospital history, psychological interview, and Wisconsin Card Classification Test (WCST). Executive performance exhibited a noticeable decline in typical and centile WCST results, as evidenced by deterioration in persistent scores, failure to maintain an attitude and difficulty learning from clinical samples. This information coincides with the evolution of the neuroimage over time. Finally, this topic is discussed in the literature.

Owing to fascinating applications of ZnO in modern devices, it is interesting to explore its more features for future devices. Hence, herein, we have synthesized the high quality ZnO spherical nanoparticles (SNPs) through a facile green synthesis route and robust structural and biomedical studies are carried out. Hexagonal phase with 93.2% crystallinity was confirmed through XRD analysis. ZnO nanoparticles were tested for their bioactivities both in vivo (acute cytotoxicity test) and in vitro (Anti-cancer activities on liver (HepG2) and cervical (Hela) cancer cell lines, stimulatory/inhibitory effects on normal rat splenic cells and hemolytic effects on red blood cells). Results showed that ZnO SNPs has no cytotoxic effects on vital organ like liver and has no hemolytic action on red blood cells. ZnO SNPs showed inhibitory consequence on normal rat splenic cells growth at all tested concentrations. ZnO nanoparticles showed an inhibitory effect on HepG2 cell line. While showed stimulatory effect on Hela cell line. Current study presents the synthesized ZnO SNPs as highly applicable in bio-optoelectronics.

In only a few months after initial discovery in Wuhan, China, SARS-CoV-2 and the associated COVID-19 disease has become a global pandemic causing significant mortality and morbidity. In the absence of vaccines and effective therapeutics, reliable serological testing can be a key element of public health policy to control further spread of the disease and gradually ease quarantine measures. However, prior to launch of large-scale seroprevalence studies to assess herd immunity, it is critical to understand the limits and potential of current SARS-CoV-2 serological tests on the market. In this study, we provide an overview of serological testing and conduct a systematic review of independent evaluations of SARS-CoV-2 serological tests performance. Our findings show significant variability in the accuracy of marketed tests and highlight several lab-based and point-of-care rapid diagnostic tests with high performance level in detecting SRAS-CoV-2 specific antibodies. The findings of this review highlight the need for ongoing independent evaluations of commercialized COVID-19 diagnostic tests.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

4-(thiazol-2-yldiazenyl)phenol (L₁) and 2-((4-hydroxyphenyl) diazenyl)-5-nitrophenol (L₂) based on azo phenol were synthesised and used as selective colorimetric sensor for CN^- and AcO⁻ ion in DMSO/H₂O-HEPES (v/v; 1:1, pH–7.3 ± 0.2) and showed good sensitivity with large red shifts and nanomolar detection limit for CN^- and AcO^- ion. The stoichiometry of L₁ with CN⁻/AcO⁻ ion was found to be 1:1 and L₂ with CN⁻/AcO⁻ ion was found to be 1:2. Binding constant for L₁+ CN⁻, L₁ + AcO⁻, L₂ + CN⁻ and L₂ + AcO⁻ were calculated by B-H plot as 1.6 × 10³, 8.0 × 10², 8.4 × 10³ and 1.7 × 10² respectively. L₂ showed high selectivity towards CN⁻ ion with low detection limit of 81 nM and large binding constant. In addition, ¹H NMR titration and DFT studies also supported the deprotonation mechanism of receptors in the presence of selective anions.

With the rapid development of China's economy, construction industrialization has become the main development trend of China's construction industry, and the convenient, efficient, environmental protection has become the new fashion, therefore the application of prefabricated building is more and more common. Stair serves as the weak link in prefab type building, the connecting node has an important influence on its failure. In this paper, pseudo-static tests are carried out on the joints in different forms of ladder holes to study the mechanical properties of flexible hinge points filled with flexible materials, and the hysteresis curve, skeleton curve and bearing capacity of each specimen are analyzed. The test results show that the flexible hinge can give full play to its flexible characteristics to ease the stress of ladder beam, pin bolt reinforcement and ladder hole, and the bearing capacity of flexible hinge points is moderate, which can not only mitigate the inclined bracing effect under the action of small and medium earthquakes, but also ensure the stair does not fall off under the action of large earthquakes. Through the experiment comparison, the ladder hole adopts node form 2, which can give full play to the advantage of flexible material.

Background: The aim of this study was to compare energy expenditure (EE) predicted by accelerometery (EEAcc) with indirect calorimetry (EEMETA) in individuals with hemiparesis. Methods: Twenty-four participants (12 with stroke and 12 healthy controls) performed a six-minute walk test (6MWT) during which EEMETA was measured using a portable indirect calorimetry system and EEACC was calculated using Bouten’s equation (1993) with data from a 3-axis accelerometer positioned between L3 and L4. Results: Median EEMETA was 9.85 [8.18;11.89] W·kg-1 in the stroke group, and 5.0 [4.56;5.46] W·kg-1 in the control group. Median EEACC was 8.57 [7.86;11.24] W·kg-1 in the control group and 8.2 [7.05;9.56] W·kg-1 in the stroke group. EEACC and EEMETA were not significantly correlated in either the control (p=0.8) or the stroke groups (p=0.06). The Bland-Altman method showed a mean difference of 1.77±3.65 W·kg-1 between EEACC and EEMETA in the stroke group and -2.08±1.59 W·kg-1 in the controls. Conclusions: The accuracy of the predicted EE, based on the accelerometer and the equations proposed by Bouten et al, is low in individuals with hemiparesis and impaired gait. This combination (sensor and Bouten's equation) is not yet suitable for use as a stand-alone measure in clinical practice for the evaluation of hemiparetic patients.

Background. In a cannot ventilate cannot intubate situation, careful preoxygenation with high FiO₂ allowing subsequent apneic oxygenation can be life-saving. The best position for an oxygen supply line within the human airway at which oxygen insufflation is more effective than standard preoxygenation with a face mask, or comparably effective as intratracheal insufflation, is unknown. Methods. In this experimental study, we compared effectiveness of preoxygenation by placing an oxygen cannula at the nose entrance, through the nose at the soft palatine, or at the base of tongue; as control we used ambient air. We connected a fully preoxygenated test lung on one side to an oximeter with a flow rate of 200ml/min simulating oxygen consumption of a normal adult, and on the other side to the trachea of an anatomically correctly shaped airway manikin over a 20 min observation period five times for each cannula placement in random order. Results. Oxygen percentage in the test lung dropped from 100% in all groups to 53±1% in the ambient air control group, to 87±2% in the nasal cannula group, to 96±2% in the soft palatine group, while it remained at 99±1% in the base of tongue group (p=0.003 for soft palatine vs base of tongue; and p<0.001 between all other groups). Conclusions. When simulating apneic oxygenation in a preoxygenated manikin, oxygen insufflation at the base of tongue kept oxygen percentage at baseline values of 99% demonstrating a complete block for ambient air flowing into the manikin’s airway. Oxygen insufflation at the soft palatine or insufflation via nasal cannula were less effective in regard of this effect.

Background: The role of inhaled Nitric Oxide (iNO) in managing Acute Respiratory Distress Syndrome Covid-19 related (C-ARDS) is debatable. The study aimed to analyze the effect of iNO administration in patients with persistent severe hypoxia and Intensive Care Unit (ICU) mortality. Methods: This retrospective study included 98 consecutive critically ill patients with C-ARDS admitted to ICU from 1 October 2020 to 31 October 2021. Results: Of these patients, 28% had received iNO. Twelve (44.4%) were responders. Kaplan-Mayer plot shows mortality was higher in non-responders (86.6 vs 25.0%). Non-response to iNo was the most important predictive value (p. 0.01). The Receiver Operating Characteristic (ROC) curve for a percentage increase in PaO2 from baseline confirmed that it had a higher predictive value for in-hospital survival. A value of 19% can predict the death event with a sensitivity of 81.8% and a specificity of 81.2%. Conclusions: Therefore, we propose to use iNO as a vasoreactivity test for prognostic stratification in patients with persistent severe hypoxia.

This brief note aims to explain the scope in conducting large-scale serological surveys of SARS-CoV-2 to define the landscape of population immunity without overlooking the inherent uncertainty steaming from sampling design and diagnostic validity. The note completes with a succinct statistical appendix of simple methods for estimating prevalence from random population samples using imperfect diagnostic tests.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

We ascertain the in vitro Benznidazole (BZN) and Nifurtimox (NFX) susceptibility pattern of epimastigotes, trypomastigotes, and amastigotes of 21 T. cruzi strains, from patients, reservoir and triatomine bugs of various geographic origin. Using this panel of isolates, we compute the Epidemiological cut off value (CO_wt). Then, the frequency of the susceptible phenotype (Wild type) towards BZN and nifurtimox (NFX) within this set of strains belonging to 3 discrete typing units (DTUs), TcI, TcII, and TcV was deduced. We have observed that the susceptibility status of individual T. cruzi isolates toward BZN and NFX is related to the genetic background and to underlying factors probably related to the individual life trait history of each strain. Analyzing drug susceptibility in this conceptual framework would offers the possibility to evidence a link between isolates expressing a low susceptibility level (not wild-type) as define by the CO_wt value and none-curative treatment. It will also permit to tract drug-resistant parasites in T. cruzi population.

Land Surface Temperature (LST) is a basic parameter in energy exchange between the land and atmosphere and is frequently used in many sciences such as climatology, hydrology, agriculture, ecology, etc. LST time series data have usually deficient, missing and unacceptable data caused by the presence of clouds in images, presence of dust in atmosphere and sensor failure. In this study, Singular Spectrum Analysis (SSA) algorithm was used to resolve the problem of missing and outlier data caused by cloud cover. The region studied in the present research included an image frame of MODIS with horizontal number 22 and vertical number 05 (h22v05). This image involved a large part of Iran and Turkmenistan and Caspian Sea. In this study, MODIS LST sensor (MOD11A1) was used during 2015 with 1×1 Km spatial resolution and day/night LST data (daily temporal resolution). The results of the data quality showed that cloud cover caused 36.37% of missing data in the studied time series with 730 day/night LST images. Further, the results of SSA algorithm in reconstruction of LST images indicated the Root Mean Square Error (RMSE) of 2.95 K between the original and reconstructed data in LST time series in the study region. In general, the findings showed that SSA algorithm using spatio-temporal interpolation in LST time series can be effectively used to resolve the problem of missing data caused by cloud cover.

Proprioceptive deficits accompanied with motor paresis after stroke, namely sensory ataxic motor paresis has a poorer prognosis of recovery than pure motor deficit. We aimed to investigate the effects of repetitive peripheral magnetic stimulation (rPMS) on sensory ataxic upper extremity (UE) paresis at acute stroke. Eighteen stroke participants with sensory ataxic UE paresis were randomized. rPMS group received five sessions of intervention per week, where 20 minutes of rPMS prior to 20 minutes of physical therapy (PT) every other day, alternating with 40 minutes of PT. The control group received five sessions of 40 minutes of PT/week. Outcome measures were Wolf motor function test (WMFT), UE motor section of Fugl-Meyer Motor Assessment Scale (FMA-UE), and Thumb localizing test (TLT). All assessments were compared before and after intervention. rPMS group received mean 6.5 sessions and the control group received 12.8 sessions, showing significantly imbalanced intervention due to different timing of hospital discharge. The imbalance was corrected by calculating gains of motor scores divided by sessions as Progress Rate (PR). Corrected gains (PR) of rPMS group was more significantly enhanced in WMFT and FMA-UE than control groups. rPMS group tended to improve TLT more than control one. rPMS might improve sensory ataxic UE paresis after stroke and proprioceptive deficit.

Abstract: The Inconel 625 is a nickel-based alloy has been widely used in the high-temperature application. The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier effect. The aim of this work is to evaluate the mechanical properties at high temperatures of the Inconel 625. The tensile tests were performed in the temperature range of room temperature until 1000 °C and strain rate of 2x10^-4 to 2x10^-3 s^-1. The creep tests were performed in the temperature range of 600-700 °C, in the stress range of 500-600 MPa in a constant load mode. The surface fracture was observed by optical and scanning electron microscopy. Serrated stress-strain behavior was observed in the curves obtained at 200 to 700 °C, which was associated with the dynamic strain aging effect. The yield strength and the elongation values show an anomalous behavior as a function of the test temperature. An intergranular cracking was observed specimen tensile tested at 500 °C that can be attributed to the decohesion of the carbides along the grain boundaries. The fracture surface of the specimen tensile tested at 700 °C showed the predominance of transgranular cracking with tear dimples with a parabolic shape.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

While the language model using the stop sign as an independent token has been widely used to decide when the model should stop, it may lead to the growth of vocabulary dimensions and further problems. Similarly, present research on game algorithms usually estimate stopping point related problems based on the evaluation of the winning rate. However, information redundancy may also exist in such models, thus increasing the training difficulty. Above two types of tasks (and similar autoregressive tasks) show a common problem of stopping point prediction. In this paper, we describe a design of separated model, trying to separate the complexity of stopping point prediction from the main task model, so that the information used for estimating stopping point can be reduced. On this basis, in order to verify the rationality of using separated model, we propose a model-free test method. It judges the separability of transformed data based on point difference and sequence difference metrics. In this way, it can predict the credibility of the separated model inference.

in this work formulations of "environmentally compatible" silicone-based antifouling synthesized in the laboratory and based on copper and silver on silica/titania oxides have been characterized, capable of replacing the non-ecological antifouling paints currently on the market. The texture properties and the morphological analysis of these powders with an antifouling action indicate that their activity is linked to the nanometric size of the particles and to the homogeneous dispersion of the metal on the substrate. The presence of two metal species on the same support limits the for-mation of nanometric species and therefore the formation of homogeneous compounds. The presence of the antifouling filler (specifically the one based on TiO2 and Ag) facilitates the achievement of a higher degree of cross-linking of the pure resin, and therefore a better compactness and completeness of the coating. This leads to a consequent better degree of adhesion to the tie-coat and therefore to the steel support used for the construction of the boats.

In this paper, particular attention is paid to an advanced variant of the plug-in hybrid engine, known as PHEV, which combines two functionalities: the vehicle's internal combustion engine (ICEV) and the electric engine (BEV). The paper also presents the assumptions of the DEVS model, which allows for the estimation of vehicle’s energy consumption. The study described herein also presents the influence of factors such as ambient temperature and constant speed on the PHEV’s energy consumption. It has been shown that the vehicle’s range estimated based on its electronic control module (ECU) is about 20% shorter per annum on average for its year-round operation in every-day driving conditions. When analyzing the energy consumption based on the vehicle’s unit energy consumption model, attention was paid to values that are strongly correlated with the traffic volume and weather conditions affecting the moving vehicle. In addition, the authors emphasized that the estimated total energy consumption of an electric (BEV) or hybrid (PHEV) vehicle, relative to the normative values arising from the type approval test cycle, deviate from the actual values arising from real driving conditions and often vary substantially. In extreme cases, the actual range of a hybrid vehicle is 75% shorter.

The aim of this study was to evaluate the Hapo ms, a passive upper limbs exoskeleton developed to assist workers for tasks with arms in front of the body. Twelve participants had to perform a static task, a manual handling task and a load carrying task two times: with and without the exoskeleton. In all cases subjective (perceived effort in arm and back areas, comfort) and objective (muscular activity, postural balance) criteria were evaluated. Results have shown a decrease in anterior deltoid (-12 to -18% depending of the task) and in biceps brachii (-19% to -33% depending of the task) muscular activity. No significant difference was pointed out in back muscle and postural balance was not significantly perturbed due to the wear of the exoskeleton. Finally, perceived effort reduction was observed during the three tasks (except in back area for task 1). To conclude, the Hapo ms seems well adapted to assist upper arms during tasks with arms in front of the body.

Studies on the structure of economic systems are, most frequently, carried out by the methods of informational statistics. These methods, often accompanied by a wide range of indicators (Shannon entropy, Balassa coefficient, Herfindahl specialty index, Gini coefficient, Theil index etc.) around which a wide literature has been created over time, have a major disadvantage. Such weakness is related to the imposition of the system condition, therefore the need to know all the components of the system (as absolute values or as weights). This restriction is difficult to accomplish in some situations, and in others, this knowledge may be irrelevant, especially when there is an interest in structural changes only in some of the components of the economic system (either we refer to the typology of economic activities - NACE or of territorial units – NUTS). This article presents a procedure for characterizing the structure of a system and for comparing its evolution over time, in the case of incomplete information, thus eliminating the restriction existent in the classical methods. The proposed methodological alternative uses a parametric distribution, with subunit values for the variable. The application refers to Gross Domestic Product values for five of the 28 European Union countries, with annual values of over 1,000 billion Euros (Germany, Spain, France, Italy and United Kingdom) for the years 2003 and 2015. A form of the Wald sequential test is applied to measure changes in the structure of this group of countries, between the years compared. The results of this application validate the proposed method.

Since the 1970s, land subsidence has been developing rapidly in the Beijing Plain, the systematic study of its evolution mechanism is of great significance to the sustainable development of the regional economy. First, based on ENVISAT ASAT and RADARSAT2 data, the land subsidence data in Beijing Plain were obtained using permanent interferometer technology. Second, based on the GIS platform and using fishing net tools, vector data of ground settlement with different resolutions were obtained. Through a series of tests, a scale of 960 metres was selected as the research unit, and the subsidence rate of the grid was obtained from 2004 to 2015. Finally, based on the Mann-Kendall mutation test method, a trend analysis of land subsidence changes in various grids was carried out. The results showed that single-year mutation mainly distributed in the middle and lower parts of the Yongding River alluvial fan and the Chaobai River alluvial fan, mainly occurring in 2015, 2005 and 2013, respectively. The upper and middle alluvial fan of the Chaobai River, the vicinity of the emergency water source and the edge velocity of the groundwater funnel have undergone several sudden changes. Combined with hydrogeology, basic geological conditions and the impact of the South-to-North Water transfer project, we analysed the causes of the mutations in the grid. The research results can provide a basis for the study and prevention of land subsidence in this area and help to further explore the trend characteristics of land subsidence in this area.

In this paper a robust version of the Wald test statistic for composite likelihood is considered by using the composite minimum density power divergence estimator instead of the composite maximum likelihood estimator. This new family of test statistics will be called Wald-type test statistics. The problem of testing a simple and a composite null hypothesis is considered and the robustness is studied on the basis of a simulation study. Previously, the composite minimum density power divergence estimator is introduced and its asymptotic properties are studied.

Introduction: Biliary Atresia (BA) is a common cause of neonatal cholestatic jaundice which, if recognized and treated early, can be life-saving for the infant. If the liver biopsy suggests the presence of BA, exploratory laparotomy is then carried out to confirm the diagnosis, along with the Kasai procedure to provide drainage to the bile secreted by the liver. The purpose of this study is to get a deep dive into all the various imaging modalities that can diagnose BA more effectively and with absolute certitude, thus helping prevent several children from a grave prognosis.Methodology: For the collection of the data, a search was done by two individuals using PubMed, Google Scholar, and Cochrane Library databases for all relevant literature. Each qualifying paper was evaluated independently by two reviewers. Each article was analyzed for the number of patients, their age, procedure modality, complexity of ethology, and incidence of the pre-decided complications. The statistical software packages RevMan (Review Manager, version 5.3), SPSS (Statistical Package for the Social Sciences, version 20), Google Sheets, and Excel in Stata 14 were used to perform the statistical analyses. The data was obtained and entered into analytic software.Results: A total of 39 studies with 3,679 subjects were selected for the study, out of which 7 studies showed sensitivity above or equal to 95%, and an astounding 14 studies showed specificity above 95%. The value of True Positive (TP) was 1280, that of True Negative (TN) was 1817, that of False Positive (FP) was 239, and that of False Negative (FN) was 343. With a confidence interval of 95%, sensitivity, specificity, and positive predictive values were calculated. The sensitivity of Ultrasonography for Biliary Atresia is 0.79, with a CI of 95% in a range of 0.77 to 0.81. The specificity of Ultrasonography for Biliary Atresia is 0.88, with a CI of 95% in a range of 0.87 to 0.90. Conclusion: Even though several radiological techniques at present help to detect BA, USG of the abdomen proves to be an effective diagnostic and a modest screening test for the detection of BA.

Lumpy skin disease (LSD) is a viral disease of cattle and water buffalo characterized by cutaneous nodules, biphasic fever and lymphadenitis. LSD is endemic in Africa and Middle East but in recent years has spread in different Asian countries. Drop of animal productions, vaccination campaign, surveillance costs and trade restrictions have significant impact on the economy of affected countries. The disease is well characterized in cattle while little is known in buffaloes and no experimental studies have been conducted in this species. Six buffaloes and two cattle were inoculated with an Albanian LSD virus (LSDV) field strain. Over a period of 42 days animals were clinically monitored and sampled for serological and virological analysis. Only two buffaloes showed clinical sign, fever, skin nodules and lymphadenitis. All samples tested in real time PCR (blood, swabs, biopsies and organ) gave negative results. Three buffaloes seroconverted at day 39 and 42 post-inoculation, detected by ELISA, but all sera were negative in serum neutralization test. Cattle showed more severe clinical signs. Moreover, viraemia and virus shedding were proven by positive PCR results and antibodies were detected by both ELISA and serum neutralization test. These findings demonstrated the limited susceptibility of buffaloes compared to cattle once experimental infected with LSDV. Further studies are needed to investigate the epidemiological role of the buffaloes.

An analysis of the performance of Automatic Dependent Surveillance-Broadcast (ADS-B) data received from the Grand Forks, North Dakota International Airport was carried out in this study. The purpose was to understand the vulnerabilities of Universal Access Transceiver (UAT) ADS-B system and recognize the effects on present and future Air Traffic Control (ATC) operation. The Federal Aviation Administration (FAA) mandated all the General Aviation aircraft to be equipped with ADS-B. The aircraft flying within United States and below the transition altitude (18,000 feet) are more likely to install an UAT ADS-B. At present unmanned aircraft systems (UAS) and autonomous air traffic control (ATC) towers are being integrated into the aviation industry and UAT ADS-B is a basic sensor for both class 1 and class 2 Detect and Avoid (DAA) systems. As a fundamental component of future surveillance system, the anomalies and vulnerabilities of ADS-B system need to be identified to enable a fully utilized airspace with enhanced situational awareness. The data received was archived in GDL-90 format, which was parsed into readable data. The anomaly detection of ADS-B messages was based on the FAA ADS-B performance assessment report. The data investigation revealed ADS-B message suffered from different anomalies including drop out; missing payload; data jump; low confident data and altitude discrepancy. Among those studied, the most severe was drop out and 32.49% of messages suffered from this anomaly. Dropout is an incident where ADS-B failed to update within a specified rate. Considering the potential danger being imposed, an in-depth analysis was carried out to characterize message dropout. Three flight parameters were selected to investigate their effect on drop out. Statistical analysis was carried out and Friedman Statistical Test identified that altitude affected drop out more than any other flight parameters.

Swimming pools are examples of water-intensive facilities, where solutions for reducing economic and environmental costs are increasingly frequently searched. One of the solutions is the recovery of water from wastewater, including from washings obtained through the process of rinsing filter bed. The study objective was the qualitative and quantitative assessment of post-coagulation sludges, the main pollutant found in the washings. During the analyses, assessment of the sedimentation capabilities of the sludges was performed (gravitationally), particle size distribution was assessed (particle size distribution analyzer) and assessment of phytotoxicity with the use of plant indicators in short-term tests was performed (Lemna minor, Lepidium sativum, Sinapis alba, Raphanus sativus). The samples were collected from two independent circulations, which differed in terms of capacity and type of coagulant used. The tested post-coagulation sludges were characterized by high content of total suspended solids: in samples from Circulation 1 from 251 to 128 mg/l, in Circulation 2 from 489 to 228 mg/l. However, the sedimentation processes enabled significant separation of sludges. The hydrolyzed coagulant contributed to the improvement of sedimentation capabilities of sludges. Despite the fact that in many samples low sludge concentrations favored stimulation of plant growth, the post-coagulation sludges can constitute a hazard to plant growth, particularly in the long-term perspective.

The lack of accurate and feasible diagnostic tests poses a significant challenge to visceral leish-maniasis (VL) healthcare services in endemic areas. To date, various VL diagnostic tests have been or are being developed, and their diagnostic performance needs to be assessed.. In the present study, the diagnostic performance of rk39RDT, Direct Agglutination Test (DAT), Microscopy, Loop Mediated Isothermal Amplification (LAMP), and miniature direct-on-blood polymerase chain reaction - nucleic acid lateral flow immunoassay (mini-dbPCR-NALFIA) was assessed using quantitative polymerase chain reaction (qPCR) as reference test in an endemic region of Ethiopia. In this study, 235 patients VL suspected patients and 104 non-endemic healthy controls (NEHC) were recruited. Among the VL-suspected patients, 144(61.28%) tested positive with qPCR. Sensi-tivities for rk39 RDT, DAT, Microscopy, LAMP assay, and mini-dbPCR-NALFIA were 88.11%, 96.50%, 76.58%, 94.33%, and 95.80%, respectively. Specificities were 83.33%, 97.96%, 100%, 97.38%, and 98.92% for rk39 RDT, DAT, Microscopy, LAMP assay, and mini-dbPCR-NALFIA, respectively. In conclusion, Rk39 RDT and microscopy exhibited lower sensitivity, while DAT demonstrated excellent performance. LAMP and mini-dbPCR-NALFIA showed excellent perfor-mance with feasibility to implement in remote endemic areas, although the latter requires further evaluation in such regions.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

The present paper investigates the influence of the specimen size of EN-AW6082 wrought aluminium alloy subjected to very high cycle fatigue (VHCF) tests. The hourglass specimens were tested under fully reversed loading condition, up to 10^9 cycles, by means of the ultrasonic fatigue testing machine developed by Italsigma® (Italy). Three specimens groups were considered, with a diameter in the middle cross-section ranging from 3 mm up to 12 mm. The stress field in the specimens was determined numerically and by strain gauge measurements in correspondence of the cross-section surface. The dispersion of experimental results has been accounted for, and data are reported in P-S-N diagrams. The decrease in fatigue resistance with increasing specimen size is evident. Theoretical explanation for the observed specimen-size effect is provided, based on Fractal Geometry concepts, allowing to obtain scale independent P-S*-N curves. The fatigue life expectation in the VHCF regime of the EN-AW6082 aluminium alloy full-scale components is rather overestimated if it is assessed only from standard small specimens of 3 mm in diameter. Experimental tests carried out on larger specimen, and a proper extrapolation, are required to assure safe structural design.

Organophilic nano clay is the composition of mostly clay and organic molecules designed to improve various materials' physical and chemical properties. Permanent deformation in asphalt pavements is primarily the result of inadequate compaction, excessive loading, and high temperatures. Rutting can result in aquaplaning, leading to accidents and costly maintenance and rehabilitation works that drain the economy. Such behavior of asphalt pavements may be attributable to poor selection of aggregate, asphalt binder, or substandard asphalt binders. This study used different percentages of organophilic nano clay ranging from 3.0% - 5.0% with two penetration grade bitumen, i.e., N.R.L 60-70 &amp; N.R.L 80-100. Adding organophilic nano clay to asphalt binder significantly reduced the rutting potential under cyclic loading at high temperatures (55 °C). Ten modified formulations and two virgin bitumen specimens were prepared. The modified binders' viscosity and rutting were tested using the Rotational Viscometer and Wheel Tracker Test (W.T.T.), respectively. The results were analyzed using software for Statistical Analysis. It was recorded that organophilic nano clay-modified bitumen significantly affected rutting to interpret the results. The results indicated that rutting decreased and viscosity increased in all nano clay-modified bitumen samples, with a 4.5% O.N.C modified binder showing the most significant improvement.

Background: Prismatic cover test (PCT) is a gold standard assessment of strabismus angle, however it has a significant number of disadvantages which are eliminated in Strabiscan device. Methods: Patients with strabismus (n = 30) and a group of healthy subjects (n = 30) were given a detailed history and underwent ophthalmologic examinations (best corrected visual acuity assessment, cycloplegic autorefractometry, biomicroscopic examination of anterior and posterior part of the eye). Each patient and healthy subjects were then subjected to the PCT, and then the presence of strabismus was detected, and its angle assessed using a Strabiscan demonstrator. Statistical analysis was done with Statistica software. Results: No statistically significant differences were noted in the measurements of strabismus angles made by the differing methods. Among the control group, using the Strabiscan demonstration device, low-angle latent strabismus ≤3PD was diagnosed in 83% of patients, and >3PD in 13% of patients. Those using the PCT, on the other hand, diagnosed latent strabismus ≤3PD in only 13% of patients, and latent strabismus with an angle >3PD in 13% of patients. Conclusion: The Strabiscan demonstration device provides quick and accurate assessment of the strabismus angle.

The study of mechanical properties of rock mass can be effectively carried out through rock-like material model test. The similarity of mechanical properties between rock-like material and protolith is dependent on the appropriate selection of composition and content of rock-like materials. In this research, X-Ray diffraction test was conducted to analyze the composition of deep rock, which confirmed silica, quartz, and dolomite as the primary components of deep sandstone. An orthogonal design test was used to execute the ratio test of rock-like material. River sand was used as an aggregate, cement as a binder, gypsum powder as a regulator, and polystyrene foam (EPS) as rock damage simulation material. The influencing factors considered in the orthogonal mechanical tests were the proportion of aggregate and binder, ratio of binder and regulator, quantity of damage simulation material, and size of damage simulation material. Three levels were set for each factor, and mechanical parameters such as compressive strength, tensile strength, elastic modulus, axial strain, and Poisson's ratio were tested for each group of samples. The changes of those parameters with the levels of the above four factors were studied. The study revealed that adjusting the size of polystyrene foam (EPS) can adjust the values of elastic modulus, tensile strength, and Poisson's ratio of rock-like material. Similarly, changing the ratio of binder and regulator can adjust the values of axial strain and compressive strength of rock-like material. The rock-like material developed in the study can simulate the mechanical properties of different rock masses such as granite, sandstone, shale, and limestone.

Migratory flows and international travel are triggering an increase in imported cases of schistosomiasis in non-endemic countries, with serology being the recommended method for screening migrants. The present study aims to evaluate, for the first time, the LAMP technique on patients’ urine samples for the diagnosis of imported schistosomiasis in a non-endemic area in comparison to a commercial immunochromatographic test and microscopic examination of feces and urine. A prospective observational study was conducted in sub-Saharan migrants attending at the Tropical Medicine Unit, Almería, Spain. For schistosomiasis diagnosis, serum samples were tested using an immunochromatographic test (Schistosoma ICT IgG-IgM). Stool and urine samples were examined by microcopy. Urine samples were evaluated by combining three LAMP assays for the specific detection of Schistosoma mansoni and S. haematobium, and an assay for the genus Schistosoma. To evaluate the diagnostic accuracy of Schistosoma-LAMP in comparison to microscopy and Schistosoma ICT IgG-IgM test, a Latent Class Analysis (LCA) was performed. A total of 115 patients were included; 21 patients (18.3%) were diagnosed with schistosomiasis confirmed by microscopy, with S. haematobium being the most frequent species identified (18/115; 15.7%). The Schistosoma ICT IgG-IgM test resulted 100% positive and Schistosoma-LAMP was 61.9% positive, reaching as high as 72.2% for S. haematobium. The sensitivity and specificity estimated by LCA, respectively, were: 92% and 76% for Schistosoma ICT IgG-IgM, 68% and 44% for Schistosoma-LAMP and, 46% and 97% for microscopy. The Schistosoma-LAMP technique presented a higher sensitivity than microscopy for the diagnosis of imported urinary schistosomiasis, which could improve the diagnosis both in referral centers and in centers with limited experience or scarce resources and infrastructure.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

The article focuses on derivation of simplified predictive models for identification of overall compressive stiffness and strength of corrugated cardboards. As a representative example an unsymmetrical 5-ply sample (with E and B flute) was used in this study. In order to exclude unreliable displacement measurement in the standard edge crush test, the virtual strain gauges are used. Video extensometry is employed here to collect measurements from the outer surfaces of the sample on both sides. Additional data allows for obtaining real force-displacement curves, which are used in the validation procedure. To emulate the experimental results, beside simple analytical model, also a 3D numerical model fully reflecting the geometry of the corrugated board, based on finite elements method was also built. In both cases a good agreement between the experimental results and the analytical and numerical calculations was observed. This proves that the proposed analytical model can be successfully used to determine the overall stiffness and compressive strength of the corrugated board, provided that the geometry and properties of all the layers of the board are known. The simple model presented in this work enables quick and reliable design and prototyping of new assemblies without the need to manufacture them.

Drug hypersensitivity reactions (DHR) to platinum-based compounds (PC) are on the rise, and their personalized and safe management is essential to enable first-line treatment of these cancer patients. This study aimed to evaluate the usefulness of basophil activation test by flow cytometry (BAT-FC) and the newly developed sIgE-microarray and BAT-microarray in diagnosing IgE-mediated hypersensitivity reactions to PC. 24 patients with DHR to PC (20 oxaliplatin and four carboplatin) were evaluated: 13 patients diagnosed as allergic with positive skin tests (STs) or drug provocation tests (DPTs), six patients diagnosed as non-allergic with negative STs and DPTs, and five patients classified as suspected allergic because DPTs could not be performed. In addition, four carboplatin-tolerant patients were included as controls. BAT-FC was positive in 2 of 13 allergic patients, with a sensitivity of 15.4% and specificity of 100%. However, the sIgE- and BAT-microarrays were positive in 11 of 13 DHR patients, giving a sensitivity of over 84.6% and a specificity of 90%. Except for one patient, all samples from the non-allergic and control group were negative for the sIgE- and BAT-microarrays. Our experience indicates that sIgE- and BAT-microarray could be helpful in the endophenotyping of IgE-mediated hypersensitivity reactions to PC and may provide an advance in decision-making for drug provocation testing.

When designing the battery of an electric vehicle, different parameters must be considered to obtain the safest arrangement of the battery/modules/cells from the mechanical and thermal point of view. In this study, the thermal runaway propagation mechanism of lithium-ion cells is analyzed as a function of their arrangement within a battery pack in case of a fire propagation of a battery pack in which a thermal runaway has occurred. The objective is to identify which cell/module arrangement is most critical within the battery pack by microscopic analysis of the structure and chemical composition of the most damaged cells, both horizontally and vertically, of a battery belonging to a burnt vehicle. And their final condition has been compared with the condition of new cells of the same type. In this way the structure and chemical composition of the anode, cathode and separator after Thermal Runaway has been compared. This research has been carried out to obtain information to understand the mechanical properties of lithium-ion cells and their behavior after thermal runaway heating leading to the propagation of a fire. Through the analysis carried out, it is concluded that cells placed in a vertical arrangement have worse behavior than cells in a horizontal arrangement. Regarding the safety of the battery, the results of this study will allow to determine which arrangement and structure of the cells within the battery pack is safer against thermal runaway due to thermal failure.

Ethiopia has been known for its recurrent droughts and poverty due to extreme climate change and variability affecting agricultural production. This study was, therefore, conducted to analyze the seasonal and inter-annual variability in rainfall and temperature v over the past three decades in western Tigray. The study consisted of 34 years of temperature and rainfall data from nine stations in two administrative zones in the western part of Tigray. The climate data was obtained from the National Aeronautic Space Administration (NASA) from 1983 to 2016. Total rainfall, simple daily intensity index, Rx1day and Rx5day, and maximum and minimum temperature, tropical nights, diurnal temperature range, cold spell and warm spell duration indicator values, cold days and cold nights, warm days, and warm nights were analyzed. RClimDex software was employed to analyze the trends and quality control of the extreme rainfall and temperature indices; in addition, the Mann-Kendall test was also used to detect the changes and variability of the variables. The trend analysis showed that there was significant (p&lt;0.05) variability in extreme temperatures, with maximum and minimum temperatures varying from 0.04 to 0.051 0C, and 0.022 to 0.031 0C, respectively. The results also revealed that there was a negative trend in extreme rainfall, with no uniform pattern. The highest and smallest reduction in the annual rainfall was 14.6 mm and 8.4 mm, which were observed at Maygaba and Adigoshu, respectively. More than 60% of the total rainfall was received in July and August throughout the study areas, with the maximum monthly rainfall of 294.2 mm observed at Adiremets. Finally, this study demonstrated that areas in the northwestern and western zones of Tigray were significantly affected by extreme rainfall and temperature variability, which subsequently affected crop yield, natural resources, food security, and the livelihood of the community during the last three decades.

Oak woodlands are a keystone ecosystem that may not be sustainable under ongoing fire management regimes and climate change. For example, in 2014, sassafras saplings started to emerge in degraded woodlands at the 1200 ha Drury Conservation Area as part of research at the Bull Shoals Field Station in Taney County, Missouri where burning was initiated in 1999. After Spring (March) 2021 burnt, we examined trend in the potential community and ecosystem effects, we assessed sapling density, height, and specific leave weigh (SLW) of white oak and sassafras (<1.0 m) from fall 2021 through fall 2022. In fall 2021, sassafras density was 560/0.1ha with mean height of 25.42cm and SLW of 0.00436g/cm² while white Oak density was 171/0.1ha with mean height of 10.2cm and SLW of 0.00680g/cm. However, in fall 2022, Sassafras density was 582/0.1ha with mean height of 71.689cm and SLW of 0.00366 g/cm² meanwhile, white Oak density was 213/0.1ha with mean height of 50.544cm and SLW of 0.00563 g/cm². We analyzed mass loss for sassafras and white oak after buried for 198 days. The weight loss for sassafras was 0.857g while oak was 0.790g for 61 days of buried. Subsequent sassafras weight loss was 1.942g, 3.343g, 4.222g and 4.82g while that of white Oak was 1.877g, 2.862g, 3.344g and 4.28g for day 105, 153 and 198 respectively. The nutrients composition and carbon sequestration of sassafras and white oak species need to be determined to better understand the effect of their dominance in fire management regime of degraded oak woodland in Southwest Missouri Ozarks.

The process of testing software is examining the artifacts and behavior of the software under test by validating and verifying it. Testing can provide valuable information about the software. Given an input to the system, there is a challenge of distinguishing correct from potentially incorrect behavior, which is the test oracle problem. Although the combinatorial testing approach can effectively reduce the number of test cases, the manual inspection of the outputs is still required. In this paper, we propose an approach to automatically classify the return pages with conducting combinatorial testing based on page similarities and hierarchical clustering, by which potential output anomalies can be identified. In the experiment, we apply our approach to a real-world e-commerce website, an anomaly can be found with the visualization of the clustering hierarchy, which suggests the potential of the applicability of the approach.

High prevalence of allergic disorders in Indian pediatric patients demands early diagnosis of allergens so that appropriate allergen avoidance methods, pharmacotherapy or immunotherapy can be provided in time to avoid the worsening of symptoms due to triggers. In this context, identification of the most prevalent aeroallergens in a given area is critical for diagnosis and treatment of various allergic reactions especially in case of rhino-conjunctivitis and asthma. The specific diagnosis of IgE mediated allergy is usually based on the correlation between the clinical history and signs and symptoms endorsed by the diagnostic tests. Skin prick tests are the gold standard however has some limitation. In view of this, the aim of this study was to assess the significance of ImmunoCAP assay for assessing serum specific IgE levels, available in India, against skin prick test by standardized allergens, for the diagnosis of allergic sensitization. A single-center observational study was conducted at tertiary care corporate hospitals in North India from 2017-2020. Patients with self-reported allergic symptoms or whose symptoms were suspected for allergies were tested for the type of sensitization using skin prick test (SPT) after their consents followed by ImmunoCAP based quantification of serum specific IgE levels. A total of 256 (95.9%) pediatric patients were analyzed in the study and were analysed. The patients were most commonly (30% patients) sensitized to D. farinae (173 [67.6%]), D. pteronyssinus (174 [68.0%]), Acarus siro (93 [36.3%]), Lepidoglyphus destructor (96 [37.5%]), Plantago lanceolata (Engl.). The ROC curve of Bermuda grass shows that the AUC of serum-specific IgE is larger than that of SPT (1.000 / 0.881). The receiver operating characteristic (ROC) analysis of serum-specific IgE reference method resulted in the largest AUC of all the allergens taken into consideration (0.711 / 1.000) compared to those of SPT (0.589 / 1.000). These results revealed that serum-specific IgE is more reliable method over prick test for accessing the sensitivity of patient for various allergens. This study may be helpful in performing early diagnosis of allergies as well as in taking appropriate preventive measures for managing life threatening allergic reactions

The magnetic heating effect for the superconducting quarter-wave resonator (QWR) cavities is investigated, and the Q slopes of the superconducting cavities are measured with an increasing accelerating field. Physical phenomena for zero-temperature limit are introduced. Bardeen–Cooper–Schrieffer (BCS) resistance and Casimir force are calculated for the zero-temperature limit. The vertical test is shown for the performance test of the quarter-wave resonator (QWR) cavities. The parameters for the quarter-wave resonator (QWR) cavity are presented. The Q slopes are measured as a function of an accelerating electric field at 4.2 K. The surface resistance of the superconducting cavity increases with an increasing peak magnetic field. The magnetic defects cause the degradation for the quality factor. From the magnetic degradation, we can find the magnetic moments of the superconducting cavities. All the quarter-wave resonator (QWR) cryomodules are installed in the tunnel, and beam commissioning is performed successfully.

Background: The maximal one-repetition test (1-RM) is widely used in scientific research; however, there are conflict results regarding its reproducibility in elderly population. The present study aimed to analyze the reproducibility the test both before and after a 12 week training period by using the bench press and leg press 45° 1-RM tests in the elderly taking into consideration the training experience and strength level of the women. Methods: Elderly women (n = 376; age, 68.5 ± 14.1 years; height, 162.7 ± 5.5 cm; body mass, 71.2 ± 16.0 kg) who underwent ≥3 months of resistance training performed an initial week of familiarization and a second week of testing and retest, with a 48–72 hour interval. Results: The results showed maximal and relative load strength of 39.3 kg and 0.59 kg/body mass for lower limbs and 20.9 kg and 0.31 kg/body mass for upper limbs. The Kappa indices were 0.93 and 0.95, and the intraclass correlation coefficients were 0.99 and 0.99 for the lower and upper limbs, respectively. Conclusion: Therefore, the present study confirms that the 1-RM test has high reliability and reproducibility in the elderly, for both upper and lower limbs.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

Chenodeoxycholic acid (CA) is a naturally occurring bile acid that is produced in the liver from cholesterol. Three CA complexes using Zn(II), Mg(II), and Ca(II) ions were synthesized to examine the chelation tendencies of CA towards these metal ions. The complexation reaction of CA with the metal ions under investigation was conducted with a 1:1 molar ratio (CA to metal) at 60-70°C in natural media (pH 7-8), which consisted of a binary solvent of MeOH and H2O (1:1). The resulting CA complexes were characterized using analytical data (metal, H, C, and Cl, analysis) and spectral data (UV-visible, FT-IR, and 1H NMR) to elucidate the complexes’ structures. The results suggested that CA in anion form utilized oxygen atoms of the carboxylate group (-COO−) to capture Zn(II), Mg(II), and Ca(II) ions. This produced complexes with the general compositions of [Zn(CA)(H2O)Cl], [Mg(CA)(H2O)Cl]H2O, and [Ca(CA)(H2O)Cl]2H2O, respectively. The Kirby-Bauer disc diffusion assay was then used to explore the bioactivity of the CA complexes toward three fungal species, three Gram-positive bacteria, and two Gram-negative bacteria. The Ca(II) and Mg(II) complexes exhibited marked inhibitory effects on the cell growth of the fungal species Aspergillus niger with potency equal to 127% and 116% of the activity of the positive control, respectively. The Zn(II) and Ca(II) complexes strongly inhibited the growth of Penicillium sp., while the Zn(II) and Mg(II) complexes showed strong growth inhibition towards the Gram-negative species Pseudomonas aeruginosa.

Objectives and Background: Gestational diabetes (GDM) is a common pregnancy complication, defined as a glucose intolerance diagnosis during pregnancy. GDM is strongly associated with adverse fetal and maternal outcomes. In Germany, to screen and diagnose GDM we use a 1-hour 50g oGCT (oral glucose challenge test) followed by a 2-hour 75g oGTT if the first was pathological. This analysis examines the correlation of 75g oGTT glucose levels and fetomaternal outcome. Methods: Data of 1664 patients from a gestational diabetes consultation clinic at the Charité University hospital in Berlin, Germany, were analyzed retrospectively from 2015 until 2022. The 75g oGTT blood glucose levels were categorized into isolated fasting hyperglycemia (GDM-IFH), isolated post-load hyperglycemia (GDM-IPH) and combined hyperglycemia (GDM-CH), using the levels of the fasting, 1-hour and 2-hour values after glucose application. These subtypes were compared regarding baseline characteristics as well as fetal and maternal outcome. Results: GDM-IFH and GDM-CH women displayed higher preconceptional BMI and required insulin therapy more frequently (p<0,001). The GDM-IFH group was at higher risk of having a primary cesarean section (p=0,047), while GDM-IPH women were significantly more likely to have an emergent cesarean section (p=0,013). The offspring of GDM-IFH and GDM-CH women were born with a significantly higher mean birthweight (p<0,001) and birth weight percentiles (p<0,001) and were at increased risk of being large for gestational age (LGA) (p=0,004). Women from the GDM-IPH group delivered significantly more neonates who were small for gestational age (p=0,027) or with low fetal weight <30th percentile (p=0,003). Conclusion: This analysis shows a strong association between glucose response pattern in the 75g oGTT and adverse perinatal fetomaternal outcome. The differences among the subgroups, specifically concerning insulin therapy, mode of delivery and fetal growth, suggest an individualized approach in prenatal care after a GDM diagnosis.

Global malaria epidemiology has changed in the last decade with a substantial increase in cases and death being recorded. Over 90% of global cases and deaths occur in Sub-Saharan Africa (SSA). Tanzania accounts for about 4% of all cases and deaths reported in recent years. It is believed that several factors contribute to the resurgence of malaria, parasite resistance to antimalarials and mosquito resistance to insecticides being at the top of the list. The presence of sub-microscopic infections poses a significant challenge to malaria rapid diagnostic tests (mRDT), particularly in low-endemic areas. Our cross-sectional surveys in Handeni and Moshi, Tanzania assessed the effect of low parasite density on mRDT. A significant difference (P˂0.001) in malaria prevalence by mRDT, light microscopy (LM) and nested polymerase chain reaction (PCR) was found among age groups. In comparison to all other groups, school-age children (5-15 years) had the highest prevalence of malaria. Based on the results of this study, mRDT may miss up to 6% of cases of malaria mainly due to low-density parasitaemia. Routinely used mRDT will likely miss the sub-microscopic parasitemia which will ultimately contribute to the continued spread of malaria and hinder efforts to control and eliminate it.

The open hole tensile and flexural test of composites holds immense importance in aerospace and structural engineering. These tests provide critical insights into how composites perform under real-world conditions, allowing for the development of materials that meet rigorous standards, thereby ensuring the safety and durability of aircraft and other applications. This study investigates the influence of hole size on the open hole tensile (OHT) and flexural properties (OHF) of plane woven aramid/epoxy (AFRP), basalt/epoxy (BFRP), and aramid-basalt/epoxy (ABFRP) sandwiched laminates. Specimens with three different hole sizes viz., 4 mm, 6 mm, 8 mm were prepared and tested according to ASTM D5766 and ASTM D7264 for OHT and OHF performance respectively. Results indicated that the hybridization of aramid-basalt layers in a sandwich lay up significantly improved the mechanical performance when compared to only aramid laminate. However, with the increase in hole size the mechanical properties declined irrespective of the material. Basalt fibres showed higher hole sensitivity under tensile loading due to its brittle fracture mechanism while aramid fibres exhibited higher hole sensitivity under flexural loading which can be attributed to its the poor compressive strength. The effect of hole size on the damage mechanism has also been highlighted through scanning electron microscope (SEM). Major failure modes observed are delamination around the hole edges, ductile and brittle fibre fractures, and delamination.

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.

The current study was formulated with the aim of assessing the impact of the Extent of Drug addiction on the Family environment and interventions for drug-addicted youth in rural areas of Dir Lower Khyber Pakhtunkhwa, Pakistan. The study comprised a dependent variable (Extent of Drug addiction) and an independent variable (Family Environment). A sample size of 266 was randomly selected for primary data collection through structured interviews. The collected information was evaluated through descriptive analysis (frequency and percentage distribution) and inferential analysis, specifically utilizing the Chi-square Statistical Test. The study concluded that drug addiction among youth has an adverse impact on the family environment, leading to instability and violent behavior. Further, families of drug-addicted youth experience a high level of dissatisfaction in relationships, often culminating in divorce. Similarly, the families of drug-addicted are characterized by low cohesion, role conflict, and tolerance. Thus, the government should formulate polices and strategies for the prevention of drug addiction, with speedy implementation across all institutional dynamics, including family. Moreover, It is also crucial to rehabilitate the lifeblood of a nation (youth) in terms of socio-economic, emotional and psychological growth. These recommendations were put forward in the light of the current study.

Background: In 2020, the incidence of cancer was 844,778 cases among the population aged 0 to 19 years. Ninety percent of the population under 18 years of age lives in low- and middle-income countries, where cancer survivors report adverse outcomes. disease, which negatively impacts individuals’ general health, emotional state and external factors such as academic performance. Therefore, the objective of this article was to report the performance of the WCST and the sociodemographic characteristics of oncopediatric patients from Cali, Colombia. We report the reliability of the WCST instrument and indicate the association between the type of cancer and executive functioning in patients. Methods: In a cross-sectional observational study, 24 oncopediatric patients were interviewed and evaluated via the WCST. Results: The mean age was 12.08 years (3.98), 20.8% were women, 70.8% had a diagnosis of leukemia, 8 patients had acquired brain deficits, and more than 75% had adequate functioning in terms of the indicators of executive functions. Robust statistics were used to explore the differences between the types of diagnoses and performance in executive functions, and no statistically significant differences were found (p = 0.156). We accumulated evidence that the WCST has a reliable Cronbach's α of 0.804 and that oncopediatric patients without brain deficits had high scores for executive functions (p = 0.002) with a moderate effect size (0.727). Conclusions: The WCST is reliable for discriminating executive function among pediatric cancer patients. The evidence suggests that there are no differences between the types of cancer evaluated and executive functioning in the participants.

The reference method for cefiderocol antimicrobial susceptibility testing is broth microdilution (BMD) with iron-depleted-Mueller-Hinton (ID-MH) medium, whereas breakpoints recommended for disk diffusion (DD) are based on MH-agar plates. We aimed to compare the performance of the commercial BMD tests ComASP (Liofilchem) and UMIC (Bruker), DD and E-test using MH- and ID-MH-agar plates with the reference BMD method using 100 carbapenem-resistant-A. baumannii isolates. Standard BMD was performed according to the EUCAST guidelines, DD and E-test were carried out using two commercial MH-agar plates (bioMérieux and Liofilchem) and an in-house ID-MH-agar plate, while ComASP and UMIC were performed according to the manufacturer’s guidelines. DD performed with the ID-MH-agar plates led to a higher categorical agreement (CA, 95.1%) with standard BMD and fewer categorization errors compared to the commercial MH-agar plates (CA bioMérieux 91.1%, Liofilchem 89.2%). E-test on ID-MH-agar plates exhibited a significantly higher essential agreement (EA, 75%) with standard BMD compared to the two MH-agar plates (EA bioMérieux 57%, Liofilchem 44%), and showed a higher performance in detecting high-level resistance than ComASP and UMIC (mean log2 difference with standard BMD for resistant isolates of 0.5, 2.83 and 2.08, respectively). In conclusion, DD and E-test on ID-MH-agar plates exhibit a higher diagnostic performance than on MH-agar plates and the commercial BMD methods. Therefore, we recommend using ID-MH-agar plates for cefiderocol susceptibility testing of A. baumannii.

The employment of breast silicone implants, both in aesthetic and reconstructive medicine, is widespread thanks to their recognized biocompatibility and durability. Some critical situations, as for example in case of accidental impacts, may however induce concerns by potential patients about their use. Experimental data is collected by means of static compressive and tensile tests. Aging at 37, 60, 75° and 90° Celsius is performed in a physiological saline solution (0,9% NaCl). Impact dynamic tests are carried out using a Hybrid II anthropomorphic test dummy with the prostheses implanted. Mechanical tensile and compressive tests show mechanical degradation of the prostheses characteristics after aging. Impact dynamic tests show a great probability of breast implant rupture at speeds up to 90 km/h. Accidental events like car crashes or bad falls, are con-firmed as possible causes of significant damages to implanted prostheses. In addition, the possi-ble long-term aging of the silicone shell, although of limited relevance in terms of body compati-bility or reaction, can lead to some degradation of mechanical properties, rendering the outcome of accidental events even more worthy of attention.

In general, the stone pagoda structures with discontinuous surfaces are vulnerable to lateral forces and are severely damaged by earthquakes. After the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the earthquakes damaged numerous stone pagoda structures due to slippage, rotation and the separation of stacked stone. To evaluate seismic resistance of masonry stone pagoda structure, we analyzed the seismic behavior of stone pagoda structure using shaking table test. Shaking frequency, permanent displacement, maximum acceleration, rocking, and sliding were assessed. Responses to simulations of the Bingol, Gyeongju, and Pohang earthquakes based on Korean seismic design standard (KDS 41 17 00) were analyzed for return periods of 1,000 and 2,400 years. We found that the type of stylobate affected the seismic resistance of stone pagoda structure. When the stylobates were stiff, seismic energy was transferred from lower to upper regions of the stone pagoda, which mainly resulted in deformation of the upper region. When the stylobates were weak, earthquake energy was absorbed in the lower regions; this was associated with large stylobate deformations. The lower part of tower body was mainly affected by rocking, because the structural members were slender. The higher part of the stone pagoda was mainly affected by sliding, because the load and contact area decreased with height.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

Hazelnut is a widespread nut species, especially in Europe, that can be consumed raw or roasted, due to its pleasant taste and nutritional properties. Despite the renowned beneficial properties, hazelnuts contain several proteins capable of inducing food allergy in sensitized individuals such as Cor a 2 (profilin), Cor a 8 (lipid transfer protein), Cor a 9 (11S seed storage globulin, legumin-like) and Cor a 11 (7S seed storage globulin, vicilin-like). In the present paper we investigated the effectiveness of autoclave based treatments in decreasing the allergic potential of hazelnut as also assessed by submitting the treated material to in vivo skin prick test and to in vitro immunoblot analysis with sera of allergic individuals exposed to the treated food material. This preliminary analysis shows that autoclave treatment, preceded by hydration and/or followed by drying, seems to be a promising approach and appears to be effective in reducing the allergenicity of hazelnut in most patients, probably due to the denaturation of most major and minor allergenic proteins. This work will open to the opportunity to produce, in perspective, hypoallergenic hazelnut derivatives tolerated by the allergic subjects.

Respiratory infections constitute a major reason for infants and children seeking medical advice and visiting health facilities, thus remaining a significant public threat with high morbidity and mortality. The predominant viruses causing viral respiratory infections are influenza A and B viruses (Flu-A, Flu-B), Respiratory Syncytial Virus (RSV), Adenovirus and Coronaviruses. We aimed to record the incidence of RSV, SARS-CoV-2, Influenza A/B and Adenovirus cases with rapid antigen tests and validate the results with RT-PCR assay of upper respiratory specimens with a wide range of viral loads and (co)-infection patterns in children. Clinical samples were collected from early symptomatic children (presenting with fever and/or cough and/or headache within 5–7 days). The surveillance program was conducted in five private pediatrician dispensaries and one Pediatric care unit, from 10 January 2023 to 30 March 2023 in central Greece. The total sample of specimens collected was 784 young children and infants, of which 383 (48.8%) ware female and 401 were male (51.2%). The mean age of participants was 7.3 + 5.5 years. The sensitivity of FLU A &amp; B test was 91.15% (95% CI: 84.33% -95.67%), and the specificity was 98.96% (95% CI: 97.86% - 99.58%). The sensitivity and specificity of the adenovirus and RSV test was {92.45% (95% CI: 81.79% - 97.91%), 99.32% (95% CI: 98.41% -99.78%)} and {92.59% (95% CI: 75.71% -99.09%), 99.47% (95% CI: 98.65% - 99.86%)} respectively. Lastly, the sensitivity of the SARS-CoV-2 test was 100.00% (95% CI: 79.41%-100.00%) and the specificity was 99.74% (95% CI: 99.06% - 99.97%). We recorded proportion of incidence for the Influenza-A and B, (14.3%), - (3.44%) correspondingly, followed by the adenovirus with a proportion (6.9%) and the RSV with (3.7%) incidence proportion and finally, the SARS-CoV-2 (2.3%). The combination of a new multiple rapid test with multiple antigens, will be probably a useful tool with financial impact for health systems targeting the early detection and right treatment of respiratory infections in the emergency departments in primary health care facilities.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

The aim of this study was to identify the differences in functional fitness and quality of life among women over 60 years of age depending on their level of objectively measured physical activity (PA) according to Global Recommendations on Physical Activity for health. The study used cross-sectional design with 213 volunteered women over 60 years of age. Physical activity was monitored for 7 days of the week using Actigraph Gt3x monitor. The Senior Fitness Test battery and Hand-grip strength tests were performed to assess functional fitness. Quality of life was self-reported using short version of WHOQOL-brief questionnaire. Women who met the PA recommendations achieved slightly better results in most functional tests and all domain of quality of life. The significant differences were found in upper body strength, dynamic balance and social relationships domain of quality of life. Physical activity programs developed on the basis of WHO recommendations have the potential to improve functional capacity and quality of life. However, further experimental studies in this area are required.

The steel grid structure with bolted ball joints is gaining popularity in offshore platforms and aquaculture cages, but the corrosion resistance of these joints is a critical safety concern. This article introduces an innovative method to enhance the sealing performance of bolted ball joints, preventing seawater ingress and corrosion. The approach involves creating a sealed surface within the contact gap between the sleeve and connecting components. Circular grooves and sealing washers are added to both ends of the sleeve. A two-dimensional finite element analysis model of the bolted ball joint with the sealing structure was created using SOLIDWORKS and ANSYS. The study analyzes the sealing gasket's contact pressure at various compression levels and evaluates its performance with bubble tests for air tightness. Research results show a linear relationship between contact pressure and compression rate, with a sealing pressure of 5.95MPa achieved at a 14% compression rate. This simple, cost-effective sealing method effectively prevents corrosion from seawater, making it ideal for marine environments.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

A real-time flight simulation tool is proposed using a Virtual Reality Head-Mounted Display (VR-HMD) for airships operating in beyond the line-of-sight (BLOS) conditions. Particularly, the VR-HMD is developed for stratospheric airships flying at low/high altitudes. The proposed flight simulation tool uses the corresponding aerodynamics characteristics of the airship, the buoyancy effect, mass balance, added mass, propulsion contributions and ground reactions in the FlightGear Fight Simulator (FGFS). The VR headset has been connected to the FGFS along with the radio controller containing the real-time orientation/state of each button that is also simulated to provide better situational awareness and a Head-Up Display (HUD) that has been developed to provide the required flight data. In this work, a system was developed to connect the FGFS and the VR-capable graphics engine, Unity, to a PC and a wireless VR-HMD in real-time with minimal lag between data transmission. A balance was found for FGFS to write to a CSV file at a period of 0.01s. For Unity, the file was read every frame which translates to around 0.0167s (60 Hz). A test procedure was also conducted with a similar rating technique based on the NASA TLX questionnaire that identifies the pilot’s spare mental capacity when completing an assigned task to assure the comfortability of the proposed VR-HMD. Accordingly, a comparison has been made for the aircraft control using the desktop simulator and the VR-HMD tool. Results, showed that the current iteration of the system is ideal to train pilots on using similar systems in a safe and immersive environment. Furthermore, such an advanced portable system may even increase the situational awareness of pilots and allow them to complete a sizeable portion of actual flight tests with the same data transmission procedures in simulation. The resulting VR-HMD flight simulator is also conceived to express the ground control station (GCS) concept and transmit flight information as well as the point of view (POV) visuals in real-time using the real environment broadcasted using an onboard camera.

Bacterial adhesion to the surface of the adhesive material is an important step in the formation of plaque and enamel demineralization. In order to correlate the material composition to the specific surface roughness of the resin and to the probable more favourable adhesion of bacteria, scanning electron microscopy, combined with focus ion bean micromachining, together with stylus profilometry analysis have been in vitro performed to reveal the structural nature of three orthodontic adhesive resins used for bracket bonding and, above all, to understand how compositional factors can influence specific pivotal properties such as material’s surface roughness and robustness. In particular, we speculated about the morphological features that determine an increase in the bacterial adhesion and we proposed focused ion beam technique as a valuable tool to compare the internal structures of the polymers and to determine the peculiar mechanical properties of the examined adhesive resins.