Hip fractures are the most frequently treated fractures in the world. Of these, intertrochanteric fractures (ITFs) account for almost 50%. After surgical fixation of ITFs, nonunion is rare. Nonunions are commonly produced from mal-reduction (in varus) and/or inadequate stability of the bone-implant construct and/or fatigue failure of the implants. Other causes of nonunion include posteromedial comminution and osteoporosis. The published incidence of ITF nonunion is 1%-2%. Mechanical complications of ITFs include cut-out, excessive shortening of the proximal femur, delayed union, nonunion, early implant fracture, nail toggle and cut through/medial migration. That is why a fundamental goal in the treatment of ITFs is to achieve stable fixation in osteoporotic bone, allowing early weight bearing. Intraoperative determination of fracture stability is essential. The American Academy of Orthopedic Surgeons (AAOS) clinical practice guidelines for the management of intertrochanteric fractures (ITF) in patients older than 55 years are the following: 1) In patients with stable ITF, the use of either a sliding hip screw (SHS) or a cephalomedullary nail (CMN) is advised (strong strength of evidence). 2) In patients with reverse obliquity fractures, a CMN is recommended (strong strength of evidence). 3) Patients with unstable ITF should be treated with a CMN (strong strength of evidence). 4) In patients with ITF, a short or long CMN may be considered (limited strength of evidence).

In the history of high-performance polymer composite parts with continuous in-plane fibre reinforcement, the comparatively moderate structural-mechanical properties in their out-of- plane-z-direction and the limited load carrying capability between individual reinforcement layers within the laminated structures have always been one of the greatest challenges. Plenty of research work has been carried out to improve load transfer capability as well as fracture toughness for crack opening events between the reinforcement layers by means of out-of-plane fibre reinforcement implementation, for example by sewing or z-pinning technologies. However, the results have not become established across a wide range of applications so far, because the technologies used have led to considerable losses of in-plane strength properties. In this paper first results are presented for a new method of a low fraction z-fibre reinforcement by means of very thin diameter laser drilled holes filled with short carbon fibres, demonstrating potential to improve Mode II fracture toughness.

The integration of three-dimensional (3D) printed resin denture teeth represents a significant ad-vancement in digital dentistry. This study aimed to assess their ability to withstand chipping and indirect tensile fractures, comparing them with conventionally manufactured resin denture teeth. Four groups, each comprising 30 specimens, were examined: Group 1 featured 3D printed denture teeth (NextDent, 3D Systems, Soesterberg, The Netherlands), while the others included commer-cially obtained Ivostar Shade, SpofaDent Plus, and Major Super Lux teeth. Stereolithography 3D printing was utilized to produce methacrylate-based photopolymerized resin teeth models for Group 1, while the remaining groups were commercially sourced. Chipping and indirect tensile fracture tests were performed at a speed of 1 mm/min until fracture occurred. Statistical analysis was conducted using one-way analysis of variance (ANOVA) with Tukey's honestly significant difference multiple comparisons test (p < 0.05). Results indicated that 3D-printed teeth exhibited higher indirect tensile fracture resistance than Major Super Lux and Ivostar Shade but lower than SpofaDent Plus. Additionally, in the chipping test, buccal chipping occurred in 3D-printed resin teeth without distortion. In the indirect tensile test, the fracture line emerged near the loading point, extending cervically from the inner incline of both cusps. Overall, denture teeth produced via 3D printing with printable resin materials demonstrated sufficient fracture resistance, making them suitable for prosthetic applications.

Leaf springs are critical components for the railway vehicle safety in which they are installed. Although these components are produced in high-strength alloyed steel and designed to operate under cyclic loading conditions in the high-cyclic fatigue region, their failure is still possible to occur and hence lead to economic and human catastrophes. The aim of this document is precisely to characterise the mechanical crack growth behaviour of the 51CrV4 spring steel representative of leaf springs under cyclic conditions, that is, crack propagation in mode I. The common fatigue crack growth prediction models (Paris and Walker) considering the effect of stress ratio and parameters such as propagation threshold, critical stress intensity factor and crack closure ratio are also determined using statistical methods, which resulted in good approximations with respect to the experimental results. Lastly, the fracture surfaces under the different test conditions were analysed using SEM, with no significant differences to declare. As a result of this research work, it is expected that the developed properties and fatigue crack growth prediction models can assist design and maintenance engineers in understanding fatigue behaviour in the initiation and propagation phase of cracks in leaf springs for railway freight wagons.

Bone/fracture healing is a complex process with different steps and four basic tissue layers being affected: cortical bone, periosteum, fascial tissue surrounding the fracture, and bone marrow. Stem cells and their derivatives, including embryonic stem cells, induced pluripotent stem cells, mesenchymal stem cells, hematopoietic stem cells, skeletal stem cells, and multipotent stem cells, can function to artificially introduce highly regenerative cells into decrepit biological tissues and augment the healing process at the tissue level. Stem cells are molecularly and functionally indistinguishable from standard human tissues. The widespread appeal of stem cell therapy lies in its potential benefits as a therapeutic technology that, if harnessed, can be applied in clinical settings. This review aims to establish the molecular pathophysiology of bone healing, the current stem cell interventions that disrupt or augment the bone healing process, and finally, consider the future direction/therapeutic options related to stem cells and bone healing.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Zirconia-reinforced lithium silicate (ZLS) is utilized as a material for prosthetic tooth crowns, offering enhanced strength compared to other dental glass-ceramics. In this study, we investigate a commercial ZLS material, provided in a fully crystallized form. We examine the effects of an optional post-processing heat treatment on micro-contact damage using controlled indentation tests simulating the primary modes of contact during chewing: axial and sliding. Our findings indicate that the heat treatment does not affect mechanical properties such as the elastic modulus, hardness and indentation fracture toughness. However, it does enhance the resistance to contact damage by fracture and chipping in both axial and sliding modes, as well as the resistance to crack initiation measured from sliding tests. This improvement is attributed to the refinement of the flaw population achieved through the heat treatment. The results are analysed within the framework of contact and fracture mechanics, and the implications for prosthetic dentistry are briefly discussed.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

This is a brief critique of the functions—particularly olfactory functions—specified for the “Chemosensory Protein” (CSPs) molecule family. On the basis of these proteins’ presence in the sensory antennal lymph of locusts, odor chemosensory ligand binding functions have been hypothesized. According to this hypothesis, the entire protein molecule superfamily is referred to as “CSPs”. However, new information and developments in the field of CSP molecular research, such as the expression of CSP genes in the gut, brain, fat body, wings, epidermis, and pheromone gland, as well as gene expression profiling from most early developmental stages—that is, CSP expression well in advance of the appearance of chemical sense nerve cells—strongly suggest that the protein molecule has other roles that are unrelated to chemosensing. Moreover, CSPs are found in bacterial microbial prokaryote organisms in addition to insects and all other arthropods. Thus, we examine the molecule’s name, definition, RNA editing, protein structure, lipid binding properties, DNA interaction, and evolutionary characteristics in brief before referring to this protein family as “Chemosensory Proteins”. As a means of renaming this protein family, this review article discusses the latest findings (“CSP” is attached to the tail of bigger intracellular proteins) and attempts to compel all the data. Because of its highly conserved molecular distinctive feature (four adjacent cysteines), we propose renaming “CSPs” as “4CSPs” (4 Cysteines Soluble Proteins) and use at least for abbreviations for distinctive animal proteins the common peptide 5-letter code, such as “Bommo-4CSPs”.

Background: Olecranon fractures are common injuries of the upper limb in adults. Simple dis-placed trasverse fractures are generally surgically treated with tension-band wiring (TBW) or plate fixation (PF). The purpose of this retrospective study is to compare the clinical-functional outcome, complications and reoperation rates between TBW and PF for Mayo IIA fractures. Methods: 72 patients treated with PF or TBW at our institution, completed our survey and clinical evaluation and their demographic and clinical data were recorded and analysed. The clini-cal-functional outcomes were evaluated assessing ROMs and three validated scoring systems: the Disabilities of the Arm, Shoulder, and Hand (DASH), the Mayo Elbow Performance Score (MEPS) and the Patient American Shoulder and Elbow Surgeons Standardized Elbow Assess-ment score (pASES-e). Results: 38 patients (53%) underwent TBW and 34 (47%) PF. The mean DASH, MEPS and pASES-e scores were respectively 14.5±17.2, 80.5±14.7 and 83.6±12.4 in the TBW group and 21±21.7, 75.6±15.3 and 75.1±19.2 in the PF group (p=0.16, p=0.17 and p=0.03). The mean duration of surgery and hospitalisation period were longer in the PF group (p=0.002, p=0.37) whereas the complication and reoperation rates were higher after TBW (p=0.15, p=0.24). Conclusion: According to the literature, both TBW and PF resulted comparable valid surgical op-tions for the treatment of simple isolated displaced olecranon fractures, revealing that they both provide good/excellent outcomes with no significant differences.

Abstract Background Context Pelvic ring fractures are becoming more common in the aging population and can prove to be fatal, having mortality rates between 10% and 16%. Stabilization of these fractures is challenging and often require immediate internal fixation. Therefore, it is necessary to have a biomechanical understanding of the different fixation techniques for pelvic ring fractures. Methods A previously validated three-dimensional finite element model of the lumbar spine, pelvis, and femur was used for this study. A unilateral pelvic ring fracture was simulated by resecting the left side of the sacrum and pelvis. Five different fixation techniques were used to stabilize the fracture. A compressive follower load and pure moment was applied to compare different biomechanical parameters including range of motion (contralateral sacroiliac joint, L1-S1 segment, L5-S1 segment), and stresses (L5-S1 nucleus stresses, instrument stresses) between different fixation techniques. Results Transiliac -trans sacral screw fixation at S1 and S2 showed the highest stabilization for horizontal and vertical displacement at the sacral fracture site and reduction of contralateral sacroiliac joint for bending and flexion range of motion by 165% and 121%, respectively. DTSF (Double transiliac rod and screw fixation) model showed highest stabilization in horizontal displacement at the pubic rami fracture site, while the L5_PF_W_CC (L5-Ilium posterior screw fixation with cross connectors) and L5_PF_WO_CC ( L5-Ilium posterior screw fixation without cross connectors) showed higher rod stresses, reduced L1-S1 (approximately 28%), and L5-S1 (approximately 90%) range of motion. Conclusions Longer sacral screw fixations were superior in stabilizing sacral and contralateral sacroiliac joint range of motion. Lumbopelvic fixations displayed a higher degree of stabilization in the horizontal displacement compared to vertical displacement of pubic rami fracture, while also indicating the highest rod stresses. When determining the surgical approach for pelvic ring fractures, patient-specific factors should be accounted for to weigh the advantages and disadvantages for each technique.

This study comprehensively investigates Al2O3's mechanical properties, focusing on fracture toughness, surface energy, Young's modulus, and crack propagation. The density functional theory (DFT) is employed to model the vacancies in Al2O3, providing essential insights into this material’s structural stability and defect formation. The DFT simulations reveal a deep understanding of vacancy-related properties and their impact on mechanical behavior. In conjunction with molecular dynamics (MD) simulations, the fracture toughness and crack propagation in Al2O3 are explored, offering valuable information on material strength and durability. The surface energy of Al2O3 is also assessed using DFT, shedding light on its interactions with the surrounding environment. The combination of DFT and MD simulations provides a robust framework for a comprehensive understanding of Al2O3's mechanical properties, with implications for material science and engineering applications.

Forensic anthropologists play a key role in skeletal trauma analysis and commonly use macroscopic features to distinguish between trauma types. However, this approach can be challenging, particularly in cases of highly comminuted or incompletely recovered fractures. Histological analysis of microscopic fracture characteristics in fractured bones may thus help provide additional information on trauma type and bone fracture biomechanics in general. This study analysed the extent of microcrack damage to osteons in long bones with blunt force trauma (BFT) and gunshot trauma (GST), from both traumatic death cases and post-mortem experimental fractures. We identified four types of osteonal damage (OD). In traumatic death cases, OD affecting the inside of the osteon and compromising the Haversian canal (type 1) was found to be indicative of BFT. Moreover, OD affecting the cement line (type 3) and interstitial lamellae (type 4) was more common in the GST samples. OD affecting the inside of the osteon without compromising the Haversian canal (type 2) was not found to be indicative of either trauma type. In cases of experimental fractures, our study revealed that post-mortem fractures in dry bone samples featured the highest amount of OD, particularly of type 4. This study also found that the experimentally produced GST featured similar OD pattern to GST death cases. These findings support our hypothesis that there are distinct osteonal damage patterns in human long bones with BFT and GST, which are of relevant value for trauma analysis in forensic anthropology.

Baculovirus is a type of virus with a double stranded, circular, and super helical DNA structure, whose transcription, replication and assembly of offspring virus occur in the nucleus of the cell. However, due to the natural barrier of the cellular nuclear membrane, macromolecular substances larger than 40-60 kDa cannot directly penetrate the nuclear membrane. Therefore, baculovirus have evolved various strategies to achieve transmembrane transport of viral proteins. This article attempts to review the recent literature on mechanisms by which the DNA baculoviruses of insects transport proteins into the infected host cell nucleus. In this article, we summarise the studies of nuclear localisation signals(NLSs) in baculovirus, which are involved in the classical nuclear import pathways and review the non-classical nuclear transport pathways independent on NLS derived from baculovirus. Moreover, during the protein nuclear transport process, viruses will regulate the nuclear pathway through protein modifications. Host structure changes and other methods will create a favorable environment for the nuclear transport of viral proteins.

Background and objectives: The incidence of hip fractures in advanced age is increasing due to the aging society. In trochanteric region fractures of the femur, patient positioning can be performed various ways. The aim of this study is to clinically and radiologically compare the use of the supine hemilithotomy position, the lateral decubitus position, and the traction table when performing PFN surgery for femoral intertrochanteric fractures in the geriatric age group.Materials and Methods: A total of 170 older patients with femoral intertrochanteric fractures were included in this cross-sectional study. The patients were divided into three groups the supine hemilithotomy group, lateral decubitus group and fracture table. For the postoperative period, complications, length of stay in the intensive care unit, and length of stay in hospital were examined, while in postoperative radiographs, tip-apex distance (TAD), collodiaphyseal angle (CDA), and Cleveland-Bosworth quadrants were examined to evaluate the placement of the lag screw in the femoral head. Quality of fracture reduction was evaluated according to the modified Baumgaertner criteria.Results: The mean age of the patients was 77.77±8.8; 57.6% of patients were female. According to the modified Baumgaertner criteria, it was determined that patients with ‘poor’ reduction quality had an approximately ten times higher risk of cut-out than those with ‘good’ reduction quality. (OR = 10.111, p = 0.002, 95% confidence interval; 2.313-44.207). The duration of surgery of patient in the fracture table group was found to be higher than in the other groups, the CDA in the supine position group were found lower than in the other groups, and the TAD in the supine position group was found higher than in the other groups. Complications were mostly detected in patients who underwent surgery in the lateral decubitus position. (p<0,05) Conclusion: We believe that it is necessary to be familiar with all methods, since it is very difficult to choose the most appropriate method according to the surgeon’s experience, the hospital’s facilities and conditions, and the patient’s clinical status.

The purpose of this study was to compare the long-term clinical outcomes and quality of life measures for two fixation methods in the setting of displaced femoral neck fractures. The two groups included fixation with multiple cancellous screws (group 1) and telescopic femoral neck screws and small locking plate device (Targon FN) (group 2). Patients underwent reduction and internal fixation with either multiple cancellous screws or Targon FN device from March 2000 to January 2012. Failure endpoints included nonunion, osteonecrosis of the femoral head, and revision surgery. Patient reported outcome measures included chronic pain, ability to ambulate, and the use of ambulation assistive devices. Statistical analysis demonstrated a statistically significant lower rate of non-union and overall complication in the Targon FN group (p value < 0.001 and p value = 0.005 respectively). Logistic regression analysis showed that operative fixation with the Targon FN device decreased the odds ratio for overall complication by a factor of 0.34 (P = 0.02). There were no statistically significant differences between groups 1 and 2 in patient reported outcomes (chronic pain (p-0.21), ability to ambulate (p- 0.07), and the use of ambulation assistive device (p-0.07)). When compared to traditional cancellous screw fixation of femoral neck fractures, the Targon FN device has significantly lower complications rates and equivalent patient reported outcomes.

In the present work, the effects of ageing treatment on the microstructures of a near-β Ti alloy (TC18) are studied. The influence of ageing treatment on the tensile properties and failure mechanisms are systematically analyzed. It is found that the size and morphology of the primary α (αp) phases are insensitive to ageing temperature and time. Furthermore, the ageing temperature and time dramatically influence the precipitation of the secondary α (αs) phases. Massive αs phases precipitate and gradually coarsen, and finally weave together with increasing the ageing temperature or extending the ageing time. The thickness of αs phases is responsible for the material strengths, while the content of α phases can enhance the material ductility. The ductile characteristics of the alloy with coarser αs phases are more obvious than those with thinner αs phases. Therefore, the ageing treatment is helpful for the precipitation and homogeneous distribution of αs phases, which is essential for balancing the strengths and ductility of the studied Ti alloy.

Osteoporotic vertebral fracture is the most common fracture from osteoporosis, and are largely undiagnosed due to the mostly asymptomatic nature of the condition. It increases the risk of subsequent fractures and contributes to societal burden. Risk factors for osteoporotic fractures are found in the WHO fracture risk assessment model and used as a tool for monitoring bone health. Vertebral fractures are diagnosed from anteroposterior and lateral spine radiographs and are confirmed with an approximate loss of 20% vertebral height as compared to adjacent vertebrae. One of the most used grading for vertebral fractures is the SQ grading. Mild vertebral fractures could easily be misdiagnosed due to some peculiarities of the vertebral column. CT scan is useful for planning surgical intervention while an MRI scan can provide information about the recency of the fracture and rule out cancer-related fractures. Management depends on the severity of the fracture which could range from conservative management to surgical vertebral augmentation and decompression. Bisphosphonates are used to treat osteoporosis in acute and long-term management of fractures. Osteoimmunological therapies such as denosumab and romosozumab are new therapeutic interventions for osteoporosis while there are many other potential treatment options. Precision medicine provides an individualized treatment approach while regenerative medicine utilizes mesenchymal stem cells for fracture repair.

This is a brief critique of the functions—particularly olfactory functions—specified for the “Chemosensory Protein” (CSPs) molecule family. On the basis of these proteins’ presence in the sensory antennal lymph of locusts, odor chemosensory ligand binding functions have been hypothesized. According to this hypothesis, the entire protein molecule superfamily is referred to as “CSPs”. However, new information and developments in the field of CSP molecular research, such as the expression of CSP genes in the gut, brain, fat body, epidermis, and pheromone gland, as well as gene expression profiling from most early developmental stages—that is, CSP expression well in advance of the appearance of chemical sense nerve cells—strongly suggest that the protein molecule has other roles that are unrelated to chemosensing. Moreover, CSPs are found in bacterial microbial prokaryote organisms in addition to insects. Thus, we examine the molecule’s name, definition, RNA editing, protein structure, lipid binding properties, DNA interaction, and evolutionary characteristics in brief before referring to this protein family as “Chemosensory Proteins”. This article tries to compel and discuss the most recent information as a way to rename this protein family. Because of its highly conserved molecular distinctive feature (four adjacent cysteines), we propose renaming “CSPs” as “4CSPs” (4 Cysteines Soluble Proteins).

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

Percutaneous kyphoplasty (PKP) is a highly successful treatment option for Kümmell's disease (KD). Due to the obstruction of the fibrocartilaginous membrane at the periphery of the intervertebral vacuum cleft (IVC) and inadequate osteointegration of conventional bone cement, there is insufficient locking strength between trabecular bone and bone cement in Kümmell's disease (KD), leading to postoperative displacement of the bone cement and sub-sequent early surgical failure. However, there is no standard strategy managing this complica-tion at present. We reported a rare case of premature bone cement displacement resulting in adjacent vertebra fracture. An 80-year-old male with Kümmell's disease at T10 received per-cutaneous kyphoplasty (PKP) with bone cement leaking into the upper disc. Only 3 days after the surgery, the patient complained of severe back pain again. X-ray and MRI showed bone cement displacement at T10, adjacent vertebra fracture at T9. In consideration of poor toler-ance of open surgery for the old patient, we successfully revised by using percutaneous ky-phoplasty with multi-point anchoring technique (A-PKP). During a 10-month postoperative follow-up, the patient reported pain relief. X-ray and three-dimensional CT scan revealed no obvious progress of bone cement displacement. Although the exact mechanism underlying this rare complication remains unclear, we observed that the premature bone cement dis-placement can result in adjacent vertebra fracture especially when the pattern of bone cement is blocky. Percutaneous kyphoplasty with multi-point anchoring technique (A-PKP) appears effective in managing this complication.

The establishment of an isolation layer in submarine mining has long presented an enduring challenge. In the context of this research, we conducted a similarity simulation test to preliminarily ascertain the interplay between the thickness and extent of the isolation layer. Subsequently, we introduce an innovative approach that integrates fractal theory and the bonded block model (BBM) to simulate undersea isolation layer mining. The validation of this method hinges on on-site borehole scanning and displacement monitoring, which serve to depict the intricate fractal evolution of fractures and predict the optimal thickness of the isolation layer. Our findings affirm the robustness and validity of this method. Evaluation of the fractal dimensions of fractures reveals that a critical threshold of 1.7 exists to prevent structural failure of the isolation layer, while a limit of 1.5 is necessary to avert significant water ingress. Remarkably, the correlation dimension of the settlement time series closely aligns with the fractal dimension of the fractures, underscoring the feasibility of ensuring the safety of isolation layer mining through real-time settlement monitoring.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

This paper presents the results of experiments on the study of a hydraulic fracture interaction with a preliminary created fracture that simulates a natural fracture. A distinctive feature of the conducted experiments is the ability to use an ultrasonic sounding to measure the fracture propagation and opening simultaneously with the fluid pore pressure measurements at the several points of the porous saturated sample. It allows to obtain the pressure distributions at various experiment stages and to establish a relation between the pore pressure distribution and the hydraulic fracture propagation and its interaction with macroscopic natural fracture. The possibilities of active ultrasonic monitoring have been expanded due to preliminary calibration experiments, which make it possible to estimate the fracture opening value by attenuation of ultrasonic pulses. The experiments show that the fracture propagation is limited by the natural fracture. This is caused by the hydraulic fracturing fluid leaks into the natural fracture, so both hydraulic fracture and natural fracture compose united hydraulic system.

The continental shale layers are more complex in matrix pore-microfracture interactions and connectivity characteristics under the influence of tuff devitrification, which limits the explicit understanding of the coupling relationship between wettability and pore structure, as well as hydrocarbon flow behavior. Therefore, the influence of tuffaceous components on the reservoir formation mechanism and oil-rich effect of the continental shale formation system is a critical issue to be solved. The Upper Triassic Yanchang Formation tuffaceous shale in Ordos Basin and the Middle Permian Jingjingzigou Formation tuffaceous shale in the southern margin of Junggar Basin is taken as the research objects, using whole-rock mineral composition analysis, FE-SEM observation and digital image processing and extraction, as well as wettability angle determination and spontaneous imbibition experiments to illustrate the influence of the difference of devitrification extent on reservoir pore connectivity and interfacial wettability in two different environments of freshwater and saline lacustrine basins, and summarize the reservoir formation differential pattern under the influence of devitrification. The results show that the saline lacustrine is significantly modified by devitrification. The pore plane porosity of the devitrified tuffaceous shales in the saline lacustrine is higher than that of the tuffaceous shales in the freshwater; the oleophilic of the saline lacustrine tuffaceous shales is better than that of the tuffaceous shales in the freshwater, moreover, the pore connectivity of the saline lacustrine tuffaceous shales is better than that of the tuffaceous shales in the freshwater. Wettability and connectivity control the storage performance of shale oil in the tuffaceous shales formation system. The more oleophilic the reservoir wettability is, the better the pore connectivity is, and the better the reservoir of tuffaceous shale formation system is. According to the different extents of devitrification, two different reservoir formation models of freshwater and saline lacustrine are established, which are of great theoretical and practical significance to enrich the theory of shale oil enrichment and reservoir formation in the continental shale formation system and to guide the exploration of continental shale oil benefits.

We performed arthroscopically assisted coracoclavicular (CC) stabilization using a suture button device for modified Neer type IIb lateral clavicle fractures accompanied by CC ligament injury. The purpose of the present study was to evaluate the radiological and clinical outcomes of this procedure. Six consecutive patients with modified Neer type IIb fractures were treated with the technique and followed for 12 months. Postoperative ranges of motion (ROMs) and X-rays were evaluated every 3 months. Shoulder functional scores (University of California Los Angeles score, Japanese Orthopedics Association score), visual analog scale (VAS) scores for pain at rest, at night, and during motion, and VAS score for satisfaction were analyzed at 12 months after surgery. For the clinical outcomes, early ROM recovery and excellent outcomes were achieved. For the radiological outcomes, all patients accomplished bone union, slight superior displacement was noted in the CC distance and Dog Bone distance, and bone hole dilation was observed in the superior coracoid and inferior clavicle, but there were no critical complications. The present findings indicate that arthroscopically assisted CC stabilization with a suture button device for unstable lateral clavicle fractures can produce satisfactory radiological and clinical results.

In response to a threefold increase in osteoporotic vertebral fractures (OVF) at our institution over the past decade and the subsequent development of new fractures within a year in a third of cases, we evaluated the effectiveness of STIR MRI scans in conjunction with CT scans for initial OVF diagnosis. This study, conducted over five months, involved full spine sagittal STIR MRI scans alongside CT scans for patients over 50 with minor injury-related vertebral fractures. The independent assessments by radiologists and neurosurgeons of 64 patients revealed that while CT scans identified 161 fresh fractures, of which only 68 were previously reported, MRI detected 266 fractures, 1.65 times more than CT. CT scans showed single fractures in 27% of patients and multiple fractures in 73%, whereas MRI identified single fractures in 9% and multiple fractures in 91% of patients. Additionally, MRI demonstrated a 1.5-fold increase in adjacent fracture detection. The use of MRI influenced treatment plans in 67% of cases. Given these findings, we advocate for including a STIR MRI of the entire spine alongside CT scans in OVF cases, as it significantly enhances fracture detection and can alter treatment strategies.

Our daily activities hinge on the flexibility of our fingers, and a fractured finger can significantly disrupt these routines. The finger bones enable us to bend and fold the fingers and thumb to pick up or grasp objects and do all of our daily activities. A broken finger can cause adverse effects on our daily life activities. It is important to treat broken finger as soon as possible. Swift and precise treatment begins with capturing multiple X-rays, followed by the critical step of fracture detection in these images. Relying on the naked eye for this task carries the risk of overlooking small fractures. To address this issue an automated diagnoses of fractured fingers from images is required for which the current research employs advanced deep learning models—ResNet34, ResNet50, ResNet101, ResNet152, VGG-16, and VGG-19—to classify finger images from the Musculoskeletal Radiographs (MURA) dataset as either fractured or non-fractured. The results emphasize the consistently strong performance of ResNet models, attaining an impressive accuracy of 81.9%. This surpasses VGG models by 3.4% and establishes ResNet as the new benchmark for state-of-the-art accuracy.

The purpose of this study was to explore and develop high-resolution infrared thermal (HRIT) imaging for screening toddler’s fracture. A Toddler’s fracture is a common tibial fracture of children younger than 6 years old. Initial x-ray radiographs may not show the fracture and another x-ray during a follow-on visit is usually required. The study included 39 participants admitted to an emergency department with a suspected toddler’s fracture. X-ray confirmed 8 cases with a toddler’s fracture (20.5%). Infrared images of participants were recorded on their index visit, focusing on region-of-interests on the injured and the contralateral (uninjured) legs. The uninjured leg acted as a thermal reference. Nine statistical measures were extracted from the images: maximum, mini-mum, mean, standard deviation, median, mode, interquartile range, skewness, and kurtosis. Wilcoxon rank sum test indicated that maximum, mean, standard deviation, median, and inter quartile range temperature measures were significantly different (p<0.05) when comparing fractured and non-fractured legs. Principal component analysis of these measures highlighted distinct separation of toddler’s fracture and non-fracture cases. Similarly, plots of the statistical measures further confirmed clustering of toddler’s fracture cases. The study demonstrated that HRIT imaging can be a valuable tool for screening for toddler’s fracture.

Hard coatings like Titanium diboride (TiB2) on silicon substrates are used for interconnects. micro-electro-mechanical devices and metallurgical protective coatings were analyzed based on shallow depths of nanoindentation penetration which involves a change in the nature of the contact from Hertzian to Pyramidal both in loading as well as unloading modes. Features like ductile fracture, linear unloading, and the creation of electrical conduction paths were analyzed. These high-precision features are influenced by the thickness and crystalline nature of the films and are significant for device fabrication.

Permeability is an important transport property of porous materials, and its accurate evaluation is relevant in studying applied tasks such as CO2 injection into reservoirs and investigating groundwater quality issues. This study examines the dependence of permeability on total and connected porosity, hydraulic tortuosity, specific surface area, and mean pore radius based on the data of 408 cubic sub-volumes extracted from heterogeneous and naturally fractured cylindrical carbonate samples before and after injection of HCl solutions into them. These parameters were computed using pore-scale modeling of fluid flow. It has been shown that permeability correlates well with porosity and mean pore radius with correlation coefficients of R2≈0.65-0.79 for heterogeneous samples. It was found that the presence of natural fractures significantly influenced the relationship between permeability and other parameters. The relationship between permeability k, tortuosity τ, and specific surface area S is described by power laws k~τ-α and k~S-β, with coefficients α and β substantially exceeding those in the Kozeny-Carman equation. It was also found that there is a parabolic relationship between connected and total porosities both before and after rock dissolution with R2≈0.96-0.99. This allowed for estimation of percolation threshold porosity that are in good agreement with the literature data.

This paper conducts an extensive literature review focusing on the utilisation of crack tip plasticity as a crucial parameter in determining and enhancing crack growth models. The review encompasses a comprehensive analysis of various methodologies, predominantly emphasising numerical simulations of crack growth models while also considering analytical approaches. Although experimental investigations are not the focus of this review, their relevance and interplay with numerical and analytical methods are acknowledged. The paper critically examines these methodologies, providing insights into their advantages and limitations. Ultimately, this review aims to offer a holistic understanding of the role of crack tip plasticity in the development of effective crack growth models, highlighting the synergies and gaps between theoretical, experimental, and simulation-based approaches.

The management of blunt abdominopelvic trauma with combined hemoperitoneum and pelvic fractures is challenging for trauma surgeons. Although angioembolization can achieve hemostasis in most visceral organ injuries and pelvic fractures after blunt abdominal trauma, it cannot effectively control hemorrhage in patients with blunt bowel mesenteric injury (BBMI). This study aimed to determine the risk factors associated with hemodynamically unstable patients with BBMI and to test the hypothesis that pelvic fracture is an independent risk factor for patients with unstable BBMI and concomitant pelvic fracture to guide the therapeutic sequence for difficult-to-manage patients. This retrospective study reviewed the data of hospitalized patients with trauma between 2009 and 2021 and included 158 adult patients with surgically proven BBMI. The patients were divided on the basis of the presence of a shock episode before emergency laparotomy. The shock group included 44.3% of all patients in the study (n = 70). Clinical injury severity and prognosis for patients in the shock group were poorer than those for patients in the non-shock group, and more invasive treatments and transfusions were performed for patients in the shock group than for those in the non-shock group. Pelvic fractures were more frequently associated in the shock group than in the non-shock group (21.4% vs. 5.7%; p = 0.003). In multivariate analysis, the presence of intracerebral hemorrhage (odds ratio [OR] = 10.87, 95% confidence intervals [CIs]: 1.70–69.75) and rib fracture (OR = 5.94, 95% CIs = 1.06–33.45) were identified as independent predictors of shock, whereas the effect of pelvic fracture did not achieve statistical significance (OR = 2.94, 95% CIs = 0.66–13.13) after adjusting for confounding factors. For patients with BBMI, outcomes need to be improved during early diagnosis and treatments should be expeditiously performed on the basis of the rapid identification of unstable hemodynamic status. In unstable patients with concomitant pelvic fractures, we support the current management algorithm that recommends performing laparotomy first.

The incidence of articular injury, particularly osteochondral fractures (OCF), has seen a notable increase in recent years. Regardless of their location, fragments might be overlooked by plain radiographs which might lead to osteoarthritis in the long run. Diagnostic imaging has a pivotal role in the assessment and classification of the fracture severity, as well as the presence of any associated dislocations. These fractures require surgical intervention for the restoration of joint function and the reduction of long-term complications. The paper aims to present the surgical correction and post-operative treatment of osteochondral fractures with absorbable implants in three children. Affected areas are discussed as follows: lateral condyle of the femur, patella, and radial head. Utilising absorbable implants for the management of OCFs provides numerous advantages, including the elimination of the need for reanaesthesia and reoperation, reducing complications, and enabling early rehabilitation. This approach also minimises the period of hospitalisation and proved effective in pediatric OCF treatment.

Rapid draw-down in an earthfill dam has serious implications for dam safety regarding slope stability. The evaluation of reservoir draw-down impact on slope stability was carried out considering the case study of 8 hours of rapid draw-down of the Middle Marsyangdi Hydroelectric Power Project (MMHPP) rock-fill dam using the Limit Equilibrium Method (LEM) and stress-based Finite Element Method (FEM). The time-dependent factor of safety (FOS) was evaluated and found that the 8 hours of rapid draw-down undertaken in October 2012 for reservoir flushing was unsafe with a draw-down rate of 1.91m/h. The resulting FOS of 1.28 and 1.27 using LEM and FEM was classified as unsafe as per the US Army Corps of Engineers’ guideline, the minimum required factors of safety should be greater than 1.3. The minimum safe allowable draw-down rate of 0.76m/h for 20 hours was identified. Applying three layers of horizontal filter materials and increasing the upstream dam’s permeability provided adequate FOS results for all cases by increasing seepage discharge to reduce the destabilizing excess pore water pressure. Several gradual draw-down rates were also tested and found that FOS increases with decreased draw-down rates, as it reduces the excess pore water pressure controlled with stabilizing existing water load.

Introduction: Bone fractures may be the result of high force impact or stress, or a minimal trauma injury as a result of certain medical conditions that weaken the bones, such as osteoporosis, osteopenia, bone cancer, or osteogenesis imperfecta, where the fracture is then properly termed a pathologic fracture. Bone cancer can be primarily or secondary to metastasis. Case presentation: We report a rare case of left humerus fracture in a 59-year-old male patient due to metastatic renal cell carcinoma. Our patient had no important past medical history. He suffered from two months of left arm pain, moderate disability and fever at night. Analgesics consumption resulted in minimal relieve. Trauma history was negative. X-ray of the left arm showed an osteolytic lesion with humerus fracture. Abdominal computed tomography with contrast showed right renal mass.Radical right nephrectomy was performed in addition to alignment nailing of the left humerus fracture with biopsy. Pathology report documented clear cell carcinoma with metastatic bone. The treatment was completed by chemotherapyDiscussion: Secondary bone tumors are metastatic lesions which have spread from other organs, most commonly carcinomas of the breast, lung, and prostate, and rarely from kidney. In some cases, bone metastasis could be the first symptoms of renal cell carcinoma. Conclusion: suspected pathological bone fractures should be investigated completely. It may hide a tumor as a cause.

This study employs the phase-field regularized cohesion model (PF-CZM) to simulate crack propagation and damage behavior in porous granite. We investigate how pore radius (r), initial crack-pore distance (D), and pore-crack angle (θ) impact crack propagation. The simulation findings reveal that, with a fixed deflection angle and initial crack-pore distance, larger pores are more likely to induce crack extension under identical loading conditions. Moreover, with r and θ keeping constant, the crack extension can be divided into two stages: from its initiation to the lower edge of the pore and then from the lower edge to the upper boundary of the model. By varying the values of D and r, we derive multiple combinations of different D/r ratios and pore radii. These results demonstrate that with constant r, cracks tend to deflect toward the pore closer to the initial crack. Conversely, when D is maintained constant, cracks will preferentially deflect toward pores with a larger r. In summary, the numerical simulation of rock pores and initial cracks, based on the PF-CZM, exhibits remarkable predictive capabilities and holds significant potential in advancing rock fracture analysis.

We investigated the biomechanical behaviour of different fixations of the tibial posterior malleolus (TPM), simulating distinct situations of involvement of the tibiotalar articular surface (TTAS) through a finite element model (FEM). A 3D computer-aided design model of the left ankle was obtained. The materials used were divided according to their characteristics into ductile and non-ductile, and all materials were assumed to be linear elastic, isotropic, and homogenous. Three different fracture lines of the TPM were defined, with sagittal angles of 10º, 25º, and 45º. For biomechanical comparison, different constructions using a trans-syndesmotic screw (TSS) only (Group T), a one-third tubular plate only with (Group PT) and without (Group PS) a TSS, and a locked compression plate with (Group LCPT) and without (Group LCPS) a TSS were tested. FEM was used to simulate the boundary conditions of vertical loading. Load application regions were selected in the direction of the 700N Z axis, 90% on the tibia and 10% on the fibula. Data on the displacement and stress in the FEM were collected, including the total principal maximum (MaxT) and total principal minimum (MinT) for non-ductile materials, total displacement (desT), localized displacement at the fragment (desL), localized displacement at syndesmosis (desS), and Von Mises equivalent stress for ductile materials. The data were analyzed using ANOVA and multiple comparison LSD tests were used. For TPM fractures with a sagittal angles 10º and 25º, desL in the PT and LCP groups was significantly lower, as well as Von Mises stress in Group LCPT in 10º, and PT and LCPT groups in 25º. TPM fractures with a sagittal angle of 45º, desL in the LCP group and Von Mises stress in Group LCPS and LCPT was significantly lower. We found that any TPM fracture may indicate instability of the distal tibiofibular syndesmosis, even when the fragment is small. Our study showed that in fragments involving 10% of the TTAS, the use of a TSS is sufficient, but when the involvement is greater than 25% of the TTAS, either non-locked or locked plate must be used to buttress the TPM. In posterior fragments affecting 45% or more of the TTAS, the use of a locking plate is recommended.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

We present an investigation on the fracture of a mold, comparing it with a normal part using specific techniques, such as EDX, SEM, and AES. The EDX analysis revealed that the composition of the normal part was consistent with that of low carbon steel, mainly comprising Fe and C. In contrast, the fractured part exhibited cracks due to nonconforming nonmetallic inclusions and reticular carbides, with fractures resulting from microporosity agglomeration and cleavage fracture. The SEM and AES analyses further presented the causes of mold fracture, highlighting the mechanism by which dimples on the specimen edge contributed to the fracture. The EDX analysis confirmed that the mold experienced thermal brittleness during use. To enhance mold durability and extend its lifespan, a double-pulse electrodeposition method was employed to create a NiCo alloy coating as a replacement for the Cr layer on the metal surface. The coating exhibited a smooth and scratch-free surface. The prepared NiCo special coating significantly increased the mold yield strength by approximately 313.8%, facilitated a 13% increase in plastic deformation, and reduced fracture strain by 25%, effectively preventing mold fracture and 3improving its service life.

As the oil industry increasingly turns to unconventional low-permeability and low-porosity reservoirs, precise post-fracture production prediction is a pivotal instrument in investment de-cision-making, formulation of energy policies, and promotion of environmental assessments. Nevertheless, despite extensive research spanning decades, the precise post-fracture production prediction based on logging parameters remains an intricate task. In this study, we gathered ex-tensive logging data and segmented the post-frac gas production during well testing on the first day to enrich the dataset. Nine pipelines were then architected using various techniques of data preprocessing, feature extraction, and advanced machine learning models. Hyperparameter op-timization was executed via the GridsearchCV. To assess the efficacy of diverse models, metrics including the coefficient of determination (R2), standard deviation (SD), and root mean square error (RMSE) were invoked. Among the several pipelines explored, the PS-NN exhibited excellent predictive capability in specific reservoir contexts (an R2 value of 0.94 and an RMSE of 48.15). In essence, integrating machine learning with logging parameters effectively assesses reservoir productivity at multi-meter formation scales. This strategy not only mitigates uncertainties en-demic to reservoir exploration but also equips petroleum engineers with monitoring on reservoir dynamics, thereby facilitating reservoir development. Additionally, this approach provides res-ervoir engineers with an efficient way of reservoir performance oversight.

Cervical injuries from athletic activities are rare; they can have severe consequences if not diagnosed and managed promptly. The choice of diagnostic imaging modality is pivotal in ensuring timely and accurate diagnosis. We detail the case of a 19-year-old female athlete who sustained a C2 Durel Type II Subclass C fracture during a short-track speed skating championship. Initial evaluation using X-ray imaging at the athletic center medical facility did not detect the injury, allowing her to continue competing. Persistent pain led to further evaluation at our institution, where MRI and CT scans confirmed the fracture. Approximately 45 days post-injury, the patient underwent a successful surgical intervention utilizing O-arm CBCT navigation for C1-C2 dorsal fusion. Post-surgery, she embarked on a comprehensive rehabilitation program and fully recovered within 12 weeks. This case underscores the limitations of relying solely on X-ray imaging for diagnosing cervical fractures post-trauma. Our findings advocate prioritizing CT scans as a primary diagnostic tool in such scenarios, emphasizing the need for a robust diagnostic approach to ensure athlete safety and well.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

Hemolysin II (HlyII) – one of the pathogenic factors of Bacillus cereus, a pore-forming β-barrel toxin – possesses a C-terminal extension of 94 amino acid residues, designated as the C-terminal domain of HlyII (HlyIICTD), which plays an important role in the functioning of the toxin. Our previous work described a monoclonal antibody (HlyIIC-20), capable of strain-specific inhibi-tion of hemolysis caused by HlyII, and demonstrated the dependence of the efficiency of hemol-ysis on the presence of proline at position 324 in HlyII outside the conformational antigenic de-terminant. In this work, we studied 16 mutant forms of HlyIICTD. Each of the mutations, ob-tained by multiple site-directed mutagenesis leading to the replacement of amino acid residues lying on the surface of the 3D structure of HlyIICTD, led to a decrease in the interaction of HlyIIC-20 with the mutant form of the protein. Changes in epitope structure confirm the high conformational mobility of HlyIICTD required for the functioning of HlyII. Comparison of the effect of the introduced mutations on the effectiveness of interaction between HlyIICTD and HlyIIC-20 and a control antibody recognizing a non-overlapping epitope enabled identifying the amino acid residues N339, K340 included in the conformational antigenic determinant rec-ognized by HlyIIC-20.

Epoxy matrix composites reinforced with high-performance fibers such as carbon, Kevlar, and glass, exhibit excellent specific stiffness and strength in many mechanical applications. However, these composites are disappointingly non-recyclable and are usually disposed of in landfill sites, with no realistic prospect for biodegradation in reasonable time. In contrast, moldable composites with carbonized elastomeric matrices developed in the last decades possess attractive mechanical properties in final net-shape products and can also be incinerated or recycled. Many carbon and inorganic fillers have recently been evaluated to adjust the properties of carbonized elastomeric composites. Renewable organic fillers such as human or animal hair offer an attractive fibrous material with substantial potential for reinforcing composites with elastomeric matrices. Samples of unidirectional fiber composites (with hair volume fraction up to 7 %) and quasi-isotropic short fiber composites (with hair volume fraction up to 20 %) of human hair-reinforced nitrile butadiene rubbers (HH-NBR) were produced in the peroxide-cured and carbonized states. The samples were characterized using SEM, Raman spectroscopy and photoacoustic microscopy. Mechanical tests were performed in tension using a miniature universal testing machine. The expected effect of fiber reinforcement on the overall mechanical performance has been demonstrated for both cured and carbonized composites. Considerable enhancement of the elastic modulus (up to 10 times), ultimate tensile strength (up to 3 times) and damage tolerance was achieved. The evidence of satisfactory interfacial bonding between hair and rubber was confirmed by SEM imaging of fracture surfaces. The suitability of photoacoustic microscopy was assessed for 3D reconstruction of the fiber sub-system spatial distribution and non-destructive testing.

The fatigue crack growth rate (FCGR) of aluminium alloys under the combined influence of temperature and humidity remains a relatively unexplored area, receiving limited attention due to its intricate nature and challenges in predicting the combined impact of these factors. The challenge was to investigate and address the specific mechanisms and interactions between temperature and humidity, as in coastal environment conditions, on the FCGR of aluminium alloy. The present study conducts a comprehensive investigation on the combined influence of temperature and humidity on the FCGR of Al6082 alloy. The fatigue pre-cracked compact tension specimens were corroded for 7 days and then subjected to various temperature and humidity conditions in a thermal chamber for 3 days to simulate coastal environments. The obtained data were analysed to determine the influence of temperature and humidity on the FCGR of Al6082 alloy. An empirical model was also established to predict fatigue life cycle values under these environmental conditions precisely. The correlation between FCGR and fracture toughness models was also examined. The Al6082 alloy exhibits a 34% increase in the Paris constant C, indicating reduced FCGR resistance due to elevated temperature and humidity levels. At the same time, fatigue, corrosion, moisture-assisted crack propagation, and hydrogen embrittlement lead to a 27% decrease in threshold fracture toughness. The developed model exhibited accurate predictions for fatigue life cycles, and the correlation between fracture toughness and FCGR showed less than 10% error, indicating a strong relationship between these parameters.

Faced with difficulties stemming from the complex interactions between tight gas sand bodies and fractures when describing and identifying reservoirs, a composite reservoir model was established. By setting the supply boundary to characterize the superposition characteristics of sand bodies, a mathematical model of unstable seepage in fractured vertical wells in tight sandstone gas reservoirs was constructed considering the factors such as stress sensitivity, fracture density and fracture symmetry. The seepage law and pressure response characteristics of gas well in tight sandstone discontinuous reservoir with stress sensitivity, semi-permeable supply boundary and complex fracture topology were determined, and the reliability of the model was verified. The research results more accurately depict the pressure characteristic curve of the superposed sand body complex fracture vertical well, and provide a more comprehensive model for tight gas production dynamic analysis and well test data analysis, which can more accurately guide the dynamic inversion of reservoir and fracture parameters.

Hydraulic fracturing is an efficient method to develop oil/gas resources economically. Temporary plugging and diverting fracturing (TPDF) can generate diversion fractures perpendicular to the initial fractures and enhance the stimulated area. The aperture of the diversion fractures determines its conductivity and the oil/gas production. This work established a fluid-solid fully coupled simulation model to investigate the fracture aperture influenced by various factors during TPDF. The factors include the permeability of the tight plug, the length of the tight plug, Young’s modulus, rock tensile strength, in-situ stress contrast, the leak-off coefficient of the fracture surface, and fluid injection rate. Results show that the aperture of the previous fracture can be enlarged, and the aperture of the diversion fracture can be decreased by the tight plug. The aperture at the diversion fracture mouth is much smaller than that along the diversion fracture. Reservoirs with low Young’s modulus and high rock tensile strength can generate the diversion fracture with a wider aperture. Moreover, increasing the fluid injection rate can effectively increase the fracture mouth aperture. In this way, the risk of screenout can be lowered. This work is beneficial for the design of the TPDF and ensures safe construction.

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

The construction of sustainable road and highway networks in the world, despite numerous feasibility, pre-feasibility and execution studies, are always confronted with the demands and vagaries of foreseeable and unforeseeable natural disasters. Studying cyclones, earthquakes, fracturing and landslide zones along roads is therefore a challenge for the sustainability of these infrastructures. In many countries around the world, the methods generally used for these studies are not only expensive and time-consuming, but the results obtained are not always efficient. This work examines whether Landsat 8 (with a high cloud level) and SRTM data can be used in both equatorial and coastal Central Africa zones to produce relevant mapping, locating fracture and landslide zones, in order to contribute not only to better road layout at lower cost and in a relatively short time, but also to better prevention of geological disasters that may occur on its network. To this end, a map of the main road network was produced and validated with field data, as well as the maps of the main unstable slopes, faults and fractures zones intersecting the road or highway network. These approaches are useful for sustainable planning, management, monitoring and extension of roads worldwide especially, in Central Africa.

Fractures are the most common large organ trauma in humans. The initial inflammatory re-sponse promotes bone healing during the initial post-fracture phase, but chronic and persistent inflammation due to infection or other factors does not contribute to the healing process. The precise mechanisms by which immune cells and their cytokines are regulated in bone healing remain unclear. The use of mesenchymal stem cells (MSCs) for cellular therapy of bones injury is a novel clinical treatment approach. Bone progenitor MSCs not only differentiate into bone, but also interact with the immune system to promote the healing process. We review in vitro and in vivo studies on the role of the immune system and bone marrow MSCs in bone healing and their interactions. A deeper understanding of this paradigm may provide clues to potential therapeu-tic targets in the healing process, thereby improving the reliability and safety of clinical applica-tions of MSCs to promote bone healing.

Introduction: Suicide is the second leading cause of death among 15 to 19-years-olds in Europe. From the beginning of COVID-19 pandemic, literature confirms a significant increase in mental health disease in children and adolescents. At Bambino Gesù Pediatric Hospital emergency department (Rome, Italy) there was a dramatic increase of suicidal attempts, and particularly a rise of suicidal jumpers. Many of these patients presented vertebral fractures. Material and Methods: This retrospective study includes all suicidal jumpers with vertebral fractures treated at our Pediatric Hospital from April 1, 2017 to March 31, 2023. We collected and compared data from three years before to three years after pandemic spreading analyzing vertebral fractures. Results: From April 1 2019 to March 31, 2020 141 cases of suicide attempt arrived at Bambino Gesù Pediatric Hospital emergency department. Five of these patients were suicidal jumpers but none had a vertebral fracture. From April 1, 2020 to March 31, 2023, 362 cases of suicide attempts arrived in the same emergency department and 19 were suicidal jumpers; 12 reported vertebral fractures and were included in this study. Mean age was 14 years. Most common level of fracture was L1. Four patients presented with preoperative neurologic impairment and two cases recovered completely. There was a transforaminal sacral fracture, a spinopelvic dissociation and an Anderson-D’Alonso C2 type II fracture. Two cases with thoracolumbar vertebral fractures were conservatively treated. Seven patients were treated by percutaneous pedicle fixation to achieve an indirect decompression and to restore a better sagittal balance. Only three patients needed an open spinal surgery by posterior approach and in two cases a posterior decompression was performed. One case with cervical fractures was treated by Halo-Vest. Conclusions: Recent literature highlights concern about the consequences of COVID-19 pandemic on pediatric population mental health. This is the first report that shows a significant increase in vertebral body fractures due to suicide jumping attempt. The comparison between three years pre and post pandemic is sufficient to demonstrate a sharp increase of these cases. This could be a new epidemiological phenomenon that could persist or even increase over time because of COVID-19 pandemic.

Background: Calcaneal fractures are the most frequent traumatic injuries of the hindfoot and can cause severe disability with social and economic sequelae; since 1980 an increasing number of studies and new technologies have led to an improvement in their management and complications but treatment is still controversial. The purpose of the study to review the secondary scientific literature looking for the optimal management of calcaneal fracture; Methods: through the PubMed MEDLINE database, 4856 articles were identified; only meta-analyses and systematic reviews were included in the study. Results: 59 reviews with more than 10,000 calcaneus fractures were examined and results were divided into various topics; the majority of articles agree on the superiority of surgical versus conservative treatment; minimally invasive access to the sinus tarsi shows better results and fewer complications than traditional extended lateral access; reduction and osteosynthesis with percutaneous and/or minimally invasive techniques seem to provide better outcomes if compared to open treatments. Conclusions: The management of calcaneus fractures requires an individualized planning based on the functional demands of the patient, the type of fracture and associated injuries. New technologies and further studies may still improve the management of these lesions.

Introduction: Postoperative epidural hematomas of the cervical and thoracic spine can pose a great risk of rapid neurological impairment and sometimes require immediate decompressive surgery. Case Report: We present the case of a young patient operated on for stabilization of a two-level thoracic vertebra fracture who developed total paralysis due to an epidural hematoma postoperatively. The course of epidural hematoma was quickly reversed with the help of a con-servative technique that prevented revision surgery. The patient regained complete neurology on follow-up without any recurrent episodes. Conclusion: There is a role of similar maneuvers as described in this case to be employed in the management of postoperative epidural hematomas. However, prolonged watchful waiting should still be discouraged, and patients should remain ready for revision surgery if there are no early signs of rapid recovery.

Fatigue-related subchondral bone injury of the third metacarpal/ metatarsal (McIII/ MtIII) bone is a common cause of wastage and welfare concern in racehorses. Better understanding of bone health and strength would improve animal welfare and be of benefit for the racing industry. Porosity index (PI) of bone is an indirect measure of osseous pore size and number and is therefore an interesting indicator of bone strength. MRI of compact bone using traditional methods even with short echo times fails to generate enough signal to assess bone architecture as the water protons are tightly bound. Ultrashort echo time (UTE) sequences aim to increase the amount of signal detected in the equine McIII/MtIII condyle. Cadaver specimens were imaged using a novel dual-echo UTE MRI technique and PI was calculated and validated against quantitative CT-derived bone mineral density (BMD). BMD and PI are inversely correlated in the equine distal Mc/ MtIII with a mean r value of -0.29. The r value is significantly different between fore- and hindlimbs. Further work is needed to assess how correlation patterns behave in different areas of the bone and to evaluate PI in horses with and without clinically relevant stress injury.

Numerous reservoirs that play a significant role in worldwide petroleum production and reserves contain fractures. Typically, the fractures must form a connected network for a reservoir to be classified as naturally fractured. Characterizing the reservoir with a focus on its fracture network is crucial for modeling and predicting production performance. To simplify the solution, dual continuum modeling techniques are commonly employed. However, to use continuum-scale approaches, properties such as average aperture, permeability, and matrix fracture interaction parameters must be assigned, making it necessary to improve fracture depiction and modeling methods. This study investigates a fractured reservoir with a low matrix permeability and a well-connected fracture network. The focus is on the impact of the hyrachical fracture network on the production performance of gas-based enhanced oil recovery methods. The Discrete Fracture Model (DFN) was utilized to create comprehensive two-dimensional models for three processes: Gas Injection (GI), Water Alternating Gas (WAG), and Foam Assisted Water Alternating Gas (FAWAG). Moreover, dimensionless numbers were employed to establish connections between properties across the entire fracture hierarchy, spanning from minor to major fractures and encompassing the fracture intensity. The results indicate that the FAWAG is more sensitive to fracture types and networks than the WAG and GI processes. Hence, the sensitivity of the individual EOR method to the fracture network requires a respective depth of description of the fracture network. However, other factors, such as reservoir fluids properties and fracture properties, might influence the recovery when the minor fracture networks are excluded. This study has determined that, among the enhanced oil recovery (EOR) techniques examined, the significance of the hyrachical depth of fracture networks diminishes as the ratio of major (primary fracture) aperture to the aperture of medium and minor fractures increases. Additionally, the impact of the assisted-gravity drainage method was greater with increased reservoir height; however, as the intensity ratio increased, the relative importance of medium and minor fracture networks decreased.

Why do the eyes remain comparatively large whereas the cornea is reduced in most troglobiont mysids? Are there any important organ size-dependent functions served by non-visual eye rudiments? This issue was approached by measuring eye structures in five troglobiont species of Mysida and two Stygiomysida compared with 14 troglophile and 49 trogloxene Mysida species. The Organ of Bellonci (OB) was found in all Mysida and as first records also in Stygiomysida. The length of OBs increased with individual body length and eye length in four examined species: from postnauplioid larvae to adult stage in a troglophile and a trogloxene mysid species examined; and from juveniles to adults in a troglobiont mysid and a troglobiont stygiomysid. At the interspecific level, eye length was on average 26% shorter at a given body length while the OB was 40% longer at a given body length and 54% longer at a given eye length, respectively, in adult troglobionts compared with trogloxene mysids. The OB is clearly proliferating while the cornea is reduced in troglobionts. This points to sensory functions (possibly together with other functions). The sensory pore organ was found in all 15 Mysida species whose eyes were mounted on slides, and a first record of this organ was also found in Stygiomysida.

The surrounding rock during the coal mine excavation is prone to significant engineering disasters such as considerable deformation and rockbursts. Pressure release can improve the stress field of a deep rock mass and prevent the occurrence of dangers such as roadway collapse and coal and gas outbursts. This paper uses the ANSYS/LS-DYNA finite element software to simulate the crush area and fracture zone of a detonation charge with different diameters under in-situ stress. The stability of the surrounding rock was analyzed based on the impact stress and velocity, and was verified by field tests. The research results show that the blasting load primarily affects the damaged area near the borehole, while the in-situ stress affects the far-field crack propagation. The crack propagates in the direction of high surrounding rock pressure. When the uncoupling index is 1.5, the impact pressure of the 60 mm diameter cartridge is 8 times that of the 20 mm diameter cartridge. The impact speed can reach 2 times that of the 20 mm diameter cartridge. The high-energy event of the roof is transferred to the front of the working face, the distribution is no longer concentrated, and a better blasting pressure relief effect is achieved. The research results can help guide the prevention and control measures of rock bursts and other mining disasters.

The research on calcium leaching of 3D printed cement pastes (3DPC) exposed in aggressive water is limited, and the mechanism underlying its effect needs to be better understood. The performance anisotropy of degraded 3DPC due to calcium leaching is investigated in this paper. Samples with aggregate micro fines (AMF) and fly ash (FA) were prepared. A 6 mol/L NH₄Cl solution was used in the accelerated experiment. At specific leaching durations, performances were tested on the samples in different leaching directions. Results show that the performances of 3DPC in aggressive water have a significant anisotropic behavior. The evolution of pore defects and hydration products mainly governs the performance anisotropy of degraded 3DPC. The remaining hydration products of the surface of 3DPC leached in the Z direction are less than the other two directions because calcium ions leached in the Z direction are difficult to be compensated through weak interfaces between layers.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

It is widely reported that the mitochondrial membrane potential, ∆Ψm, is reduced in aging animals. It was recently suggested that the lower ∆Ψm in aged animals modulate mitochondrial bioenergetics and that this effect is a major cause of aging since artificially increased ∆Ψm in C. elegans increased lifespan. Here I review, critically, studies that reported reduction of ∆Ψm in aged animals, including worms, and conclude that many of these observations are best interpreted as evidence that the fraction of depolarized mitochondria is increased in aged cells because of the enhanced activation of the mitochondrial Permeability Transition Pore, mPTP. Activation of the voltage-gated mPTP depolarizes the mitochondria, inhibits oxidative phosphorylation, releases large amounts of calcium and mROS, and depletes cellular NAD+, thus accelerating degenerative diseases and aging. Since the inhibition of mPTP was shown to restore ∆Ψm and retard aging, the reported lifespan extension by artificially generated ∆Ψm in C. elegans is best explained by inhibition of the voltage-gated mPTP. Similarly, the reported activation of the mitochondrial Unfolded Protein Response by reduction of ∆Ψm, and the reported preservation of ∆Ψm in dietary restriction treatment in C. elegans are best explained as a resulting from activation or inhibition of the voltage-gated mPTP, respectively.

The outer membrane of Gram-negative bacteria contains a variety of pore-forming structures collectively referred to as porins. Some of these are voltage-dependent, but weakly so, closing at high voltages. Triplin, a novel bacterial pore-former, is a three-pore structure, highly voltage dependent, with a complex gating process. The three pores close sequentially: pore 1 at positive potentials, 2 at negative and 3 at positive. A positive domain containing 14 positive charges (the voltage sensor) translocates through the membrane during the closing process and the translocation is proposed to take place by the domain entering the pore and thus blocking it resulting in the closed conformation. This mechanism of pore closure is supported by kinetic measurements that show that in the closing process the voltage sensor travels through most of the transmembrane voltage before reaching the energy barrier. Voltage-dependent blockage of the pores by polyarginine but not by a 500 fold higher concentrations of polylysine, is consistent with the model of pore closure, with the sensor consisting mainly of arginine residues, and with the presence, in each pore, of a complementary surface that serves as a binding site for the sensor.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

The purpose of this work is to compare two fracture prediction models with real-world data. The pure Artificial Neural Network (ANN) model emphasizes regression analysis, while the hybrid model (SVM-ANN) focuses on the combination of regression and classification analysis or Support Vector Machine. The results were subsequently tested against logging data by combining the Machine Learning approach with advanced logging tools. In this context, we used electrical image logs and the dipole acoustic tool which together allowed the distinction of 404 open fractures and 231 closed fractures and, consequently the estimation of fracture porosity. The results are then fed into two machine-learning algorithms. Pure Artificial Neural Networks and hybrid models are used to establish comprehensive results, which are subsequently tested to check the accuracy of the models. The outputs obtained from the two methods demonstrate that the hybridized model has a lower Root Mean Square Error (RMSE) than pure ANN. The results of our approach strongly suggest that incorporating hybridized machine learning algorithms in fracture porosity estimations can contribute to the development of more trustworthy static reservoir models in simulation programs. Finally, the combination of Machine Learning (ML) and well-log analysis do permit reliable estimation of fracture porosity in the Ahnet field in Algeria, where, in many places, advanced logging data is absent and costly.

Based on the engineering background of Daliuta mining area, the fracture distribution and water movement within the weakly cemented overlay strata are studied through liquid-solid coupling physical simulation and COMSOL numerical simulation test. 3D fracture network of overburden strata in mining is plotted based on the result of the physical simulation test. The results showed that the ‘fractured zone’ of the weakly cemented overburden strata in the western area develops more evidently than that in the eastern area ---- wide-opened fractures form at both ends of the working area and this leads to a wide distribution of fractures in the overlying strata.After the initial caving of the roof, height of the penetrating fractures increases rapidly and the separated strata space becomes the main channel for water flow. Under the action of water flow and rock strata movement, mining-induced fractures in overlying rock display cyclic change of expansion, penetration and closure. When the working face is fully mined, the penetrating fractures in the overlying strata and mining-induced fractures up in the working face become the main passages for water flow. The experimental result provides a reference for underground reservoirs layout and maintenance and water-conserved mining in western China.

Osteoporotic spinal fractures represent an increasingly widespread health problem in our aging society. We aimed to investigate the treatment options for low-energy spinal fractures in the el-derly and their impact on mortality, focusing on surgical stabilization using minimally invasive and open techniques. We evaluated 1356 patients over 50 years of age with compression frac-tures sustained due to low energy trauma treated at a single trauma center. We compared the mortality of patients following stable and operated/non-operated unstable compression frac-tures and the eligibility to surgery using the open and minimally invasive approach. The pa-tients received surgical or conservative care according to severity and eligibility to surgery. The mortality hazard ratio of patients who underwent screw fixation was 1.02 (P > .91), of patients who refused surgery was 1.68 (P < .001) and that of patients with anesthesiological contraindica-tion was 1.57 (P = .08), compared to conservatively treated patients with stable fractures. The dif-ference in mortality between open and minimally invasive surgeries was not significant, but the number of patients eligible for surgery with the minimally invasive procedure was significantly higher (OR: 0.25; P < .001). Spinal stability after fractures may be an important predictor of sur-vival in patients with low-impact fractures.

With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

Fracture and failure performance of foamed concrete materials were conducted using three methods, i.e., inverse analysis, digital image correlation (DIC) and finite element modelling (FEM) from tested normalized notched beams under three-point bending. From this study, several characteristics both experimental and FEM are discussed. However inverse analysis is only well applicable for series GF-30. The bilinear softening of the testing beam was estimated to identify fracture energy (GF), critical crack length (ac) and elastic modulus (E) with values of 0.015 N/mm, 54.5 mm, and 13 GPa, respectively. Additionally, fracture toughness was calculated by adopting double-K (initiation fracture of 6.907 MPa.mm0.5, unstable fracture of 23.186 MPa.mm0.5 and cohesive fracture of 16.278 MPa.mm0.5). Two-dimensional FEA Modelling of fracture was carried out using a Traction Separation Law (TSL), incorporating extended finite element method (XFEM) and cohesive zone (CZM) techniques. A sensitivity study was carried out, global mesh size of two and damage stabilization cohesive with the value of 1 × 10-5 showed good convergence and were used in other models. Furthermore, by comparing experimental observation using DIC, reliability FEM was validated and showed good acceptance to simulating the crack propagation.

China is rich in coal resources under water bodies. However, for a long time, the safety prediction of high-intensity mining under water bodies is one of the problems encountered by the coal industry. It is of great significance to realize safe mining under water bodies, improve the recovery rate of coal resources and protect reservoir resources. Therefore, this article takes the No. 5 coal seam and No. 11 mining area of Wangwa Coal Mine as the research object, and integrates physical simulation, numerical simulation, theoretical analysis and other methods to study the development height of water-conducting fracture zones in fully mechanized top coal caving mining. Solid-liquid coupling physical simulation test reveals the failure characteristics of overlying strata in goaf and the seepage law of reservoir water under the influence of mining. By comparing the monitoring data of borehole leakage, the measured data obtained by borehole peeping with the height data of water-conducting fracture zone obtained by the traditional empirical formula of three-under standard, the error between the two is as high as -29.39 %. In this case, the variance correction coefficient is used to correct the empirical formula, and on this basis, in order to effectively protect the surface water dam and water body, the mining height of coal seam in the working face with limited height mining is inversely derived. The research results provide a basis for the safety prediction of high-intensity mining under the reservoir dam in the ecologically fragile areas of western China and provide a scientific guarantee for the formulation of safety measures under such conditions.

Glycans play important roles as recognition molecules on cell surfaces in living organisms due to their remarkable structural diversity. Carbohydrates exist in numerous isomeric forms and can adopt diverse structures through various branching patterns. Despite their relatively small molecular weights, they exhibit extensive structural diversity. On the other hand, lectins, also known as carbohydrate-binding proteins, not only recognize and bind to the diverse structures of glycans but also induce various biological reactions based on structural differences. Initially discovered as hemagglutinins in plant seeds, lectins have been found to play significant roles in cell recognition processes in higher vertebrates. However, our understanding of lectins in marine animals, particularly marine invertebrates, remains limited. Recent studies have revealed that marine animals possess novel lectins with unique structures and glycan recognition mechanisms not observed in known lectins. Of particular interest is their role as pattern recognition receptors in the innate immune system, where they recognize glycan structures of pathogens. Furthermore, lectins serve as toxins for self-defense against foreign enemies. Recent discoveries have identified various pore-forming proteins containing lectin domains in fish venoms and skins. These proteins utilize lectin domains to bind target cells, triggering oligomerization and pore formation in the cell membrane. These findings have spurred research into the new functions of lectins and lectin domains. In this review, we present recent findings on the diverse structures and functions of lectins in marine animals.

The pore-throat radius of shale oil reservoir is extremely small, and it is difficult to accurately obtain the absolute permeability and oil-water two-phase relative permeability of actual oil reservoir through conventional core experiments. However, these parameters are very important for reservoir numerical simulation. In this paper, a method for characterizing flow parameters based on pore network model that considers differential pressure flow and diffusion flow is proposed. Firstly, a digital core was reconstructed using focused ion beam scanning electron microscopy (FIB-SEM) from the Gulong shale reservoir in the Songliao Basin, China, and a pore network model was extracted. Secondly, quasi-static single-phase flow and two-phase flow equations considering diffusion were established in the pore network model. Finally, pore throat parameters, absolute permeability, and oil-water two-phase permeability curves were calculated, respectively. The results show that the pore throat distribution of Gulong shale reservoir is mainly concentrated in the nanometer scale, the mean pore radius is 87 nm, the mean throat radius is 41 nm, and the mean coordination number is 3.97; The calculated permeability considering diffusion is 0.000124mD, which is approximately twice the permeability calculated without considering diffusion; The irreducible water saturation of the Gulong shale reservoir is approximately 0.26, and the residual oil saturation is approximately 0.73. The method proposed in this paper can provide an important approach for characterizing the flow parameters of similar shale oil reservoirs.

Background and Objectives: The relevance of red flags in serious spinal pathology (SSP) evolved throughout the last years. Recently, new considerations have been proposed to expand the consideration of red flags. The purpose of this study was to determine, approve and test a model for the triage and manage-ment process of SSP based on the latest data available in the literature. Materials and Methods: The SSP model was initially built on the basis of a literature re-view. The model was further determined and approved by an expert panel us-ing a Delphi process. Finally, clinical scenario were used to test the applicabil-ity of the model. Results: After three rounds of Delphi process, panellists reached a consensus on a final version of the model. The use of clinical scenari-os by experts bring about reflexive elements both on the determined model and on the evocative SSP of the clinical cases. Conclusions: The validation of the model and its implementation in the clinical field could help assess the skills of first-line practitioners managing spinal painful patients. To this end, the devel-opment of additional clinical scenarios fitting with the determined model should be further considered.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

This paper reports the effect of as-deposited surface condition on the fatigue strength in an additive manufactured titanium alloy Ti-6Al-4V (WAAM Ti64). First, local stress concentration caused by the surface waviness was quantified by a metrology technique followed by numerical modelling. Fatigue tests were conducted under bending load with the as-deposited surface being under tensile cyclic stress. The applicability of two predictive methods was studied and compared with the fatigue test results. The traditional notch stress method overestimated the fatigue strength by a factor of 1.5 at a given life; the poor agreement with the test is attributed to the crack propagation from the waviness being dominant in the bending test, i.e., the crack initiation stage was short, hence the local stress method is unsuitable. The fracture mechanics approach has delivered good predictions at every applied stress levels. The method treats a waviness trough as an initial crack. This approach is suitable for predicting the fatigue life in materials built by wire based directed energy deposition processes.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

A reliable finite element procedure to simulate shear-dominated ductile fracture in large-scale, thin-walled steel structures is still evolving due primarily to the challenges in determining the fracture criterion of steel materials under complex stress states. This paper aims to examine the accuracy of the modified Gurson-Tvergaard-Needleman (GTN) model considering the shear failure in simulating ductile fracture of steel plate structures under quasi-static punch loading. The modified GTN damage models are performed by ABAQUS user defined material subroutine (VUMAT). The void related parameters and shear damage parameters of Xue’s and N-H modified GTN models are calibrated from test specimens with various geometries corresponding to different stress triaxiality and shearing conditions. The damage evolution associated with the shearing of voids in the modified GTN models has strong influences on the stress triaxiality versus equivalent plastic strain under complex stress states, especially for the shear dominated loading conditions. Based on the original GTN model, Xue’s model, and N-H modified GTN model with calibrated material parameters, a numerical comparative study examines the ductile fracture of steel non-stiffened plate and stiffened plate under punch loading. Benchmarked against the experimental studies, the numerical simulations demonstrate that the shear driven void evolution in the modified GTN model imposes significant effects on the load-displacement responses, as well as the onset and extension of ductile fracture in steel plates under punch actions. The N-H modified model with calibrated shear damage parameters shows a better correlation with the ductile fractures in steel plates observed in the experiment, than the original GTN model and Xue’s modified GTN model. As a result of this study, the modified GTN model considering the shear failure can be applied for practical applications in the crashworthiness assessment of ship collision and grounding.

An 11-month-old castrated male Pomeranian presented with nonunion following a femoral fracture that occurred after femoral head and neck osteotomy. Radiography and computed tomography revealed severe atrophy of the proximal bone fragment and retardation of the ipsilateral distal fragment and tibia. An autogenous bone graft using coccygeal bone was performed, in which three-and-a-half coccyges were placed in series and fixed using an orthogonal locking plate. To promote bone healing and facilitate proper weight bearing and ambulation, bone morphogenetic proteins, biphasic calcium phosphate, platelet-rich plasma, passive range of motion exercises, transcutaneous electrical nerve stimulation, neuromuscular electrical stimulation, and low level laser therapy were applied. During the four-year follow-up, it was observed that the previously engrafted bone healed well and maintained stability over a prolonged period, resulting in the patient being able to walk and trot comfortably with good outcomes. However, some degree of lameness was noted during galloping owing to limb shortening and joint contracture.

Weathering and erosion transport minerals and organics toward the sea or lake bottoms over geologic time. The finest solids are deposited in lower, less turbulent areas, such as lake bottoms and continental shelves. They sometimes stack up to thicknesses of kilometers, and begin compacting. These sediment sections are called shales, and as initially deposited in water, shales can have porosities up to 50-80{\%} water, As they are buried, many alteration products from oil to slate are produced due to overburden and temperature increasess, making them important to study. A preceeding paper \cite{1} showed that pressure solution is the primary mechanism for porosity reduction, with possible mechanical compaction at shallow depths. Without naming the mineral(s) involved, it postulated that the greater the product of the water and pore interfaces, the faster the reaction would proceed. This term is $ \varphi^{4m/3}(1-\varphi)^{4n/3}$ , where $\varphi$ is porosity and m and n are numbers close to unity. The large exponents, {\em 4/3}, recognize that the reaction occurs at the molecular scale at which the surfaces are rough. A second term, $\exp^{(-E/RT)}$ , indicates that the reaction is impeded by a quantum energy barrier, E, with diminished impeding power as increased available thermal energy, represented by the absolute temperature, T, becomes available at greater depths in the Earth. These two factors combine to allow porosity $\varphi$ to reduce with time, or equivalently for the fraction of solids, $(1-\varphi)$, to increase with time,$\left. \frac{\partial(ln(1-\varphi) ) }{\partial t } \right |_{\sigma} = (\varphi )^{4m/3}( 1-\varphi )^{4n/3}Ae^{-E/(RT)}$. { \em Here it is shown that this equation can cover quantitatively any actual deposition rates which may have been experienced by the six sections studied, the actual deposition rates being unknown for these cases. Hence a time-depth depositional history for any new shale section, known in detail, would allow determination of the parameters m, n, E and a lumped proportionality constant A. This was accomplished by showing that, for a wide range of depositional rates, r, the range of E for any of the studied sections is small compared to laboratory measurements of quartz solution\cite{2}, 24+-15kJ/mol. Results were obtained over this range of r's using the previously determined m and n, and porosity and temperature profiles. The presently existing porosity profiles necessarily incorporate any overpressure or underpressure conditions that may have existed in the past or currently, as the net difference between overburden and pore pressure is a primary driving force for pressure solution. $SiO_2$ usually comprises 20-50{\%} of shales. In conclusion, pressure solution of quartz can account for vertical compaction of shales quantitatively in the studied examples. Separately, a quasi-eqivalent method for discussing reduced porosities in Macron 2 versus Macron 1 as increased vertical stress, rather than additional horizontal stress, is illustrated. Experiments are suggested to clarify the pressure solution mechanism. The role of horizontal forces is discussed.

The aim of this study was to evaluate and compare the fracture resistance of definitive zirconia dioxide restorations obtained using a computer-aided design and manufacturing (CAD/CAM) system. Methods: Two groups of ten samples were analyzed for each material (n: 20), the first group was Zolid Gen X Amann Girrbach (ZGX) and the second group was Cercon HT Dentsply Sirona (CDS). The restorations were designed with identical parameters and milled with a CAD/CAM system. Each specimen was load tested at a speed of 0.5 mm/min with a direction parallel to the major axis of the tooth and with an initial preload of 10N until fracture using a universal testing machine (Universal/Tensile Testing Machine, Autograph AGS-X Series) equipped with a 20 kN load cell. The results obtained were recorded in Newtons (N), using software connected to the testing machine. Results: Statistically significant differences were found, and the fracture toughness of the monolithic zirconia crowns was lower in the CDS group (1744.84 ± 172.8 N), compared to the ZGX group (2387.41 ± 516 N). Conclusions: The monolithic zirconia CAD-CAM zirconia crowns showed sufficient fracture strength to be used in posterior molar and premolar zones with either material as they withstood fracture loads greater than the maximum masticatory force.

Sulfate attack is one of the main factors affecting the durability of concrete structures. In recent years, multi-walled carbon nanotubes (MWCNTs) have attracted the attention of scholars for their excellent mechanical properties and durability performance. In this paper, the influence of sulfate attack and dry-wet cycles on the performance of multi-walled carbon nanotube-lithium slag concrete (MWCNTs-LSC) with varied MWCNTs content (0wt%, 0.05wt%, 0.10wt% and 0.15wt%) and varied water-cement ratios (0.35, 0.40 and 0.45) were investigated. Besides, scanning electron microscopy (SEM) and X-ray computed tomography (CT) tests were conducted to analyze the microstructure and pore structure of the concrete. The results show that concrete incorporated with MWCNTs could effectively mitigate sulfate attack The resistance to sulfate attack of concrete is negatively related to the water-cement ratio when the dry-wet cycle is fixed. The MWCNTs-LSC showed the best compressive strength at the water-cement ratio of 0.35 and 0.10 wt% MWCNTs. The SEM test results showed that the MWCNTs both filled the pores and cracks within the specimen and formed bridges between the cracks, enhancing the resistance to sulfate attack. The CT test results also showed that the addition of MWCNTs could reduce the porosity of concrete, refine the pore size and inhibit the generation and development of cracks, thus optimizing the internal structure of concrete and improving its resistance to sulfate attack.

Recent advances in synthetic membranes allow their use in fields as diverse as food and agriculture, biotechnology, industrial wastewater treatment, and potable water production. Among the newly developed technologies, nanofiltration for liquids and more particularly for desalination of seawater or saline aquifers are actively pursued. However, current solid-state membranes performance is limited, which calls for the development of novel formulations for membranes offering both high permeability (ion and water flux) and ion differentiation (selectivity), usually considered antagonist features. We report the development of hybrid nanoporous membranes made of solid-state polymeric carbonate track-etched (PCTE) thin films in which biological ion channels such as Gramicidin A (GA), alpha-hemolysin (α-HL), and outer-membrane protein F (OmpF) aquaporin are confined and graphene oxide (GO) conjugated cobalt ion selective binding peptide motifs (Copep) are adsorbed, referring as bioinspired and biomimetic approaches, respectively. These solid-state nanoporous membranes are attracting widespread attention since they offer scalability, mechanical robustness, selectivity, controlled pore dimension and shape, for water sustainability. The ion permeability, ion diffusion coefficient and selective ion recognition are evaluated via nanofiltration, cell diffusion kinetics, and UV-Visible absorption spectroscopy to gain insights into the role of key performance parameters including effective ion confinement in track-etched pores, rich surface chemistry, and peptide-induced channel for selective ion transport. These findings provide new avenues for artificial ion channels by synergistic combination of eco-friendly material design such as GO enabled by bio-molecular recognition chemistry.

Indirect fracturing from roof rock to coal using a horizontal well is a new and promising technology for coalbed methane surface exploitation in soft and low-permeability coal seams. In order to study the propagation law of hydraulic fracture across the coal-rock interface, a pore pressure cohesive element is used to establish a numerical model for indirect fracturing. Combined with practical engineering in 3# coal seam in Xinjing mine in China, the propagation behavior of hydraulic fracture across the coal-rock interface was researched, and the range of horizontal well position for indirect fracturing was determined. The results show that: (1) the pore pressure cohesive element can be used to simulate accurately the interaction between hydraulic fracture and natural fracture, and the propagation of hydraulic fracture across the coal-rock interface. (2) As the vertical distance between the horizontal well and coal-rock interface decreases, the breakdown pressure of perforation decreases; while the injection pressure increases when the hydraulic fracture crosses the coal-rock interface. (3) For the indirect fracturing engineering in 3# coal seam in Xinjing mine, the vertical distance between the horizontal well and coal-rock interface should not be larger than 2.0m to make the hydraulic fracture propagate into the coal seams.

Fracture of viscoplastic materials is a complex process due to its time-dependent and plastic responses. Numerical simulation for fracture plays a significant role in crack prediction and failure analysis. In recent years, the phase field model is becoming a competitive approach to predict crack growth and has been extended to inelastic materials such as elasto-plastic, viscoelastic and viscoplastic materials, etc. However, the contribution of inelastic energy to crack growth is seldom studied. For this reason, we implement the phase field model coupled with a viscoplastic constitutive in finite element framework, in which the elastic energy and inelastic energy are used as crack driving energy. The implicit algorithm for a viscoplastic constitutive is presented, this procedure is suitable for other viscoplastic constitutive relations. The strain rate effect, creep effect, stress relaxation effect and cyclic loading responses are tested using a single element model with different inelastic energy contributions; A titanium alloy plate specimen and a stainless-steel plate specimen under tension are studied compared with the experimental observations in existing literature. The results show that the above typical damage phenomenon and fracture process can be well reproduced; The inelastic energy significantly affects the force-displacement responses but has slight effect on the crack paths.

In this paper, we propose a modeling method based on peridynamics for ductile fracture at high temperatures. A thermoelastic coupling model combining peridynamics and classical continuum mechanics is used to limit the peridynamics calculations to the failure region of a given structure, thereby reducing computational costs. Then, a plastic constitutive model of peridynamic bonds is developed to capture the ductile-fracture process of the structure. Furthermore, an iterative algorithm for ductile-fracture calculation is presented. Finally, several numerical examples are shown. Particularly, the fracture processes of a superalloy structure under 800℃ and 900℃ environments are simulated and compared with experimental results. Our comparisons show that the crack modes captured by the proposed model are similar to experimental observations, which verifies the validity of the proposed model.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Mild impacts to the head, particularly when repetitive in nature, are increasingly recognized to have a range of significant negative implications for brain health. Much of the ongoing research in the field is focused on the neurological consequences of these injuries, and the relationship between head impacts and long-term neurodegenerative conditions such as chronic traumatic encephalopathy and Alzheimer’s disease. However, our understanding of the complex relationship between applied mechanical force at impact, brain pathophysiology, and neurological function, remains incomplete. Past research has shown that mild head impacts, even below the threshold that results in cranial fracture, induce changes in cranial bone structure and morphology. These structural and physiological changes likely have implications for the transmission of mechanical force into the underlying brain parenchyma. Here, we review this evidence in the context of the current understanding of bone mechanosensitivity and the consequences of traumatic brain injuries or concussions. We postulate that heterogeneity of the calvarium including differing bone thickness due to prior impacts, age, or individual variability, may be a modulator of outcomes following subsequent head impacts. We advocate for greater consideration of cranial responses to head injury in both experimental and computer modeling of impact biomechanics, and raise the hypothesis that calvarial bone thickness represents a novel biomarker of brain injury vulnerability after head trauma.

Near-neutral pH and low redox potentials (EH) are considered favorable conditions for radionuclides immobilization in deep repository systems in clay geological formations. Cigeo is a future Industrial Centre for Geological Disposal for Nuclear Waste (NW) for high-level and intermediate level long-lived radioactive waste, to be built in France, at 500 m depth within the Callovo-Oxfordian clay formation. Deep knowledge of the mechanisms and kinetics of corrosion occurring at the external surface of tubings made of API 5L X65 carbon steel (CS-X65) in contact with COx pore water, is essential for a reversible NW management of the Cigeo site. By using robust handmade electrodes and electrochemical and gravimetric techniques, this work aimed to determine the corrosion phenomenology and kinetics of CS-X65 in contact with COx pore water flowing continuously through a Multi-Parameter Probe (MPP) device, placed at 500 m depth, for more than 180 days. It also aimed at demonstrating the reliability and the robustness of the measurement methodology for the corrosion evaluation of the metallic liner of the future nuclear waste disposal site. Two iron oxidants were encountered, oxygen, who was depleted, and proton, who was accompanied by hydrogen sulfide. Corrosion mechanisms and kinetics were well established for two CS-X65, electrochemically perturbed and not. The corrosion thickness loss rates stand between 0.016 and 0.032 mm/y.

Introduction: Fractures in older individuals are often caused by falls, with approximately 90% of hip fractures resulting from falls. The risk of falling increases with age, and while a significant portion of individuals over 65 fall at least once per year, only a small percentage of these falls result in hip fractures. Factors that influence the likelihood of a fracture occurring include the intensity of the fall and the quality of the bone, with lower bone mineral content increasing the risk of fracture. Older women, particularly those in their 70s, are significantly more prone to hip fractures and any type of fracture. Efforts to reduce the likelihood of falls or mitigate the associated trauma are more complex than treating osteoporosis, due in part to a lack of understanding of the causes and contributing factors of falls in older age.Methods: This study analyzed data from patients admitted to Carmel medical center with upper or lower limb fractures between 2017 and 2019 to determine the side of wrist fractures and compare it to patient age in order to examine whether there was a difference in the distribution of sides in distal radius fractures based on age and test the hypothesis that falls are more likely to occur on the left side due to the assumption that dominant hand gross motor skills are better preserved. The study received approval from the Institutional Helsinki Committee and used statistical analysis with a significance level of 0.05. Potential sources of bias include limited availability of reliable data for many patients and the risk of errors in fracture registration or diagnosis, although the small sample size is expected to minimize these biases.Results: In this analysis of patient data from 2019 to 2017, a binomial test found that the probability of breaking the left wrist is significantly greater than the probability of breaking the right wrist (p < 0.05), while a t-test found no difference in the distribution of fractures between the right and left wrists of the distal radius based on age (p = 0.2774). Discussion: The findings of the study are consistent with previous research, and indicate that there is no change in side preference for fractures with age. Conclusion: The probability of breaking the left wrist is approximately 1.5 times greater than the probability of breaking the right wrist.

The effect of elastic constants, cij, on the nature (easy or difficult) of a cleavage system in YBa2Cu3O7−δ is investigated, by employing a novel three-dimensional eigenfunction expansion technique, based in part on separation of the thickness-variable and partly a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism. Out of the available three complete sets of elastic constants, the first constitutes an estimate, while the second assumes tetragonal symmetry. This leaves only the experimental measurements by resonant ultrasound spectroscopy, despite reported values of c12 and to a lesser extent, c66, being excessively high. The present investigation considers six through-thickness crack systems weakening orthorhombic YBCO mon-crystalline plates. More important, the present approach predicts whether a crack would propagate in its original plane/direction or deflect to a different one. This fracture mechanics criterion is then employed for accurate determination of the full set of elastic constants of mono-crystalline YBCO. Finally, generally unavailable results, pertaining to the through-thickness variations of stress intensity factors and energy release rates for a crack corresponding to symmetric and skew-symmetric hyperbolic cosine loads that also satisfy the boundary conditions on the bounding surfaces of an orthorhombic monocrystalline plate bridge a longstanding gap in the field.

Medicinal plants for bone grafts are promising because they are free from infecting microorganisms and biocompatible. We report a novel study evaluating osteoregeneration of bone grafts from extracts of Alternanthera brasiliana and Fridericia platyphylla after bone injury induced by radius fracture in rats. Grafts were obtained using 2% chitosan gel and 0.5% hydroalcoholic extract. The rats were randomly divided into four experimental groups (N= 12): Negative control (NC) - Chitosan gel; Positive control (PC) - bovine mineral bone graft (Lumina Bone®, fine powder 0.5); F. platyphylla Graft (FRID) - 0.5% bone graft; A. brasiliana Graft (ABRA) - 0.5% bone graft. The animals were evaluated for three periods, 30, 60, and 90 days after fracture induction. Bone alkaline phosphatase (BSAP) and radiographic and histological evaluations were followed. After 90 days, there was an increase in BSAP for the ABRA group on the newly formed bone matrix but not for FRID, indicating the presence of active osteoblasts. Additionally, mature bone tissue and bone remodeling were observed, and a conspicuous presence of type I collagen for both FRID and ABRA. We demonstrated that FRID and ABRA grafts produced early bone neoformation. New perspectives for these species as a graft are suggested.

Objectives Bone fractures are very common diseases, which can be caused by impact injuries or physiological disorders. Thus, the present review aimed to study the use of medicinal plants in the healing mechanism of bone fractures. Evidence acquisition Through research in the PubMed, Google Academic, and Scielo databases, this article reviews 11 ethnopharmacological studies and 34 preclinical studies on the biological actions of different plants in bone fracture healing mechanism. Results Indian tribes have highlighted in the plants ethnopharmacological study for various diseases, including bone fractures. However, despite the large citations of traditional use, technical-scientific studies are still scarce in the literature. Chenopodium ambrosioides, Piper sarmentosum, quadrangular Cissus, Ricinus communis and Radix salvia miltiorrhiza plants were the most studied in the literature regarding their osteogenic, angiogenic, anti-inflammatory and remodeling effects, acting on bone receptors, stimulating bone metabolism, increasing minerals uptake, and assisting in free radicals breakdown. Conclusion Thus, the medicinal plants use is promising in the field of bone regeneration, as well as being alternative when conventional therapies are unfeasible, increasing herbal medicines demand and popularity.

The 1884 Andalusia Earthquake, with an estimated Magnitude between 6.2 and 6.7, is one of the most destructive events that shook the Iberian Peninsula, causing around 1200 casualties. Ac-cording to paleoseismology studies and intensity maps, the earthquake source relates to the nor-mal Ventas de Zafarraya Fault (Granada, Spain). Diverse studies registered and later analyzed hydrological effects, such as landslides, rockfalls, soil liquefaction, all-around surge and loss of springs, alterations in the phreatic level, discharge in springs and brooks, and well levels, along with changes in water properties. Further insight into these phenomena found an interplay be-tween hydro-geomechanical processes and crust surface deformations, conditions, and properties. This study focuses on analyzing and simulating the features involved in the major 1884 event and aims at elucidating the mechanisms concerning the mentioned effects. This ex-post analysis builds on the qualitative effects and visible alterations registered by historical studies. It encompasses conceptual geological and kinematic models, and a 2D finite element simulation to account for the processes undergone by the Zafarraya Fault. The study focuses on the variability of hy-dro-geomechanical features and the time evolution of the ground pore-pressure distribution in both the preseismic and coseismic stages, matching some of the shreds of evidence found by field studies. This methodology can be applied to other events registered in the National Catalogues of Earth-quakes to achieve a deeper insight, further knowledge, and a better understanding of past earth-quakes.

NASA/ESA/CSA joint venture James Webb Space Telescope is about to be launched. It is hypothesized to operate in near-infrared range. It is also hypothesized to unveil early star formation, galaxies, and universe due to its orbit, point in orbit and orbital motion. It has been under manufacturing for over 20 years at a staggering cost of 10 billion US dollars (most expensive scientific experiment in history). Beryllium (Be) is chosen to be element for construction of its main mirrors due to its high stiffness, low density, low linear coefficient of thermal expansion (α) in cryogenics and high thermal conductivity. It is followed by gold (Au) layer deposition on its (Be) surface to enhance its sensitivity towards infrared radiation as later is hypothesized to bear superior properties. However, serious mistakes have been made in selecting this material for this application. Owing to its crystal structure (hexagonal close packed (hcp)), slip planes (basal, prismatic and pyramidal) and mechanisms of their activation, Be necessitates easy fracture at cryogenic temperature. It has anisotropic properties and prone to transverse fracture under tensile loading. Furthermore, its ductile to brittle transition temperature is very low making it entirely unsuitable for such an application. It is one of most expensive metals on planet. This study constitutes revisiting these fundamental properties and mechanisms which were entirely ignored during materials selection thus rendering whole project useless.

One of the most broadly used models for membrane fouling is the Hermia model, which separates this phenomenon into four blocking mechanisms, each with an associated parameter n. These mechanisms are complete blocking (n=2), intermediate blocking (n=1), standard blocking (n=3/2), and cake formation (n=3/2). The original model, which was obtained through experimental data, is given by an Ordinary Differential Equation (ODE) dependent on n. At the time, this ODE was only solved for these four values of n, which limits the effectiveness of the model when adjusted to experimental data. This paper aims to not only mathematically prove the original Hermia model but also to broaden the scope of this model for any real number n by using the original ODE, the equations of fluid mechanics, and the properties of single and multivariable calculus. The extended Hermia model (EHM) is given by a power law for any n≠2 and is given by an exponential function at n=2. To better test the model, we have performed the model fitting of the EHM and compared its performance to the original four pore-blocking mechanisms in 6 micro- and ultrafiltration examples. In all examples, the EHM performed consistently better than the four original pore-blocking mechanisms. Changes in the blocking mechanisms concerning transmembrane pressure (TMP), crossflow rate (CFR), crossflow velocity (CFV), membrane composition, and pretreatments are also discussed.

Al-6%Mg-Sc-Zr alloys with the total ratio of Sc + Zr = 0.32 wt.% make up the target of this research. The content of scandium and zirconium varied with an increment of 0.02%. The alloys were produced by induction casting. Their ultrafine-grained (UFG) microstructure was formed with Equal Channel Angular Pressing (ECAP). Such cast alloys have a homogeneous macrostructure formed by small equiaxed grains in the central part of the ingot and columnar crystals along the edges of the cross section. After ECAP, the average grain size in the alloy specimens is 0.5–1 µm. The average grain size does not depend on the ratio of Sc and Zr in these alloys. Superplasticity tests were performed at temperatures ranging from 300 to 500 °C and at a strain rate varying between 3.3·10-3 and 3.3·10-1 s-1. UFG Al-6%Mg-0.20%Sc-0.12%Zr and Al-6%Mg-0.18%Sc-0.14%Zr alloys exhibit the highest superplasticity. It was suggested that changes in Sc:Zr ratio affect spatial distribution and composition of the following precipitating particles: Al3Sc, Al3Zr, Al3(ScxZr1-x). An increase in Zr concentration is shown to reduce the susceptibility of UFG alloys to cavitation fracture.

Introduction: Acute compartment syndrome (ACS) is a surgical emergency that requires urgent intervention in order to prevent permanent structural damage and irreversible functional disability. The diagnosis of ACS depends on a high index of suspicion, relying on the following diagnostic criteria commonly known as the 5 Ps; Pain, Paresthesia, Paralysis, Pallor, and Pulse-lessness. When the diagnosis is uncertain, intracompartmental pressure greater than 30 mmHg is suggestive of ACS. Case Presentation: We report a case of an underdiagnosed ACS, with a lack of classical presentation in a thirty-seven-years-old male patient with a history of myopathy. The patient was admitted to the emergency room due to direct trauma to his right hip, without a significant Visual Analogue Score. On his hip radiograph a subtrochanteric fracture of the right femur was demonstrated. An additional masked ipsilateral subcapital fracture was detected during the operation. The diagnosis of ACS was made during the operation while relying on the clinical appearance of the thigh and the clinical findings during surgery. Fasciotomies were performed, and open reduction with internal fixation via Proximal Femoral Nail was done. The diagnosis of ACS was confirmed later on, by the biopsy results. Conclusion: This case suggests that myopathy can mask the classical presentation of ACS. Furthermore, the extent of pain complaints and accompanying paresthesia cannot be relied on in this regard and other clinical features should be considered in order to diagnose ACS.