Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is pandemic. Prevention and control strategies require an improved understanding of SARS-CoV-2 dynamics. We did a rapid review of the literature on SARS-CoV-2 viral dynamics with a focus on infective dose. We sought comparisons of SARS-CoV-2 with other respiratory viruses including SARS-CoV-1 and MERS-CoV. We examined laboratory animal, and human studies. The literature on infective dose, transmission, and routes of exposure was limited specially in humans, and varying endpoints were used for measurement of infection. We propose the minimum infective dose of COVID-19 in humans, is higher than 100 particles, possibly slightly lower than the 700 particles estimated for H1N1 influenza. Despite variability in animal studies, there was some evidence that increased dose at exposure correlated with higher viral load clinically, and severer symptoms. Higher viral load measures did not reflect COVID-19 severity. Aerosol transmission seemed to raise the risk of more severe respiratory complications in animals. An accurate quantitative estimate of the infective dose of SARS-CoV-2 in humans is not currently feasible and needs further research. Further work is also required on the relationship between routes of transmission, infective dose, co-infection, and outcomes.

Background: COVID-19 pandemic has pulled us all a few steps back, were we never shake hands or hug each other when we meet our friends and family after a gap, but instead we greet them by saying Namaste and joining our hands together. As we all know, COVID-19 spreads through air and the only way to shield ourselves is by maintaining a safe distance from one another. Methodology: In order to conduct a meta-analysis on the number of COVID-19 cases in Kerala and India, the data was retrieved from various sites hosted by the government bodies. The data for analysis was collected from May 2020 to July 2020. The average number of days required to reach every 5000 fresh cases were also calculated using this data. COVID-19 has affected all the economy holistically regardless of financial, behavioral, or societal aspects. Conclusion: Lifting of the lockdown in a step by step process keeping in mind the necessities for the nation was a thoughtful act, but the people who mistook this opportunity and did not remain in quarantine after coming from abroad was recognized as the reasons behind the sudden and uncontrolled rise in the number of COVID-19 cases in Kerala, India. The government authorities had no other option but to lift the restrictions to reduce the economic burdens that had already affected the daily wage worker and farmers prompting them to give up their lives.

Organ-on-Chip is a game-changing technology born from the convergence of tissue engineering and microfluidic technology. Organ-on-Chip devices (OoCs) are expected to offer effective solutions to persisting problems in drug development and personalized disease treatments. This opinion paper surveys the current landscape in research, development, application and market opportunities for OoCs to help establishing a global and multi-stakeholder OoC ecosystem. Based on a bibliometric study, a market analysis, expert interviews, and panel discussions held at the ORCHID Vision Workshop (Stuttgart, 23 May 2018), we outline presently unmet needs, key challenges, barriers and perspectives of the field, and finally propose recommendations towards the definition of a comprehensive roadmap that could render OoCs realistic models of human (patho)physiology in the near future.

Effects of the convection flow, atmospheric diffusivity and humidity on evolution and travel distances of exhaled aerosol clouds by an infected person are considered. The aim of this work is to evaluate the importance of aerosol transmission routes and the effectiveness of the 2-metre separation distance policy. A potential impact of use of face masks on the infection transmission rate, and an opportunity to reduce infection in hospitals, care homes and other public spaces by appropriate monitoring and filtering of air are also considered. The results obtained demonstrate that aerosol particles generated by coughing and sneezing can travel over 30 m. Modelling of the evolution of aerosol clouds generated by coughing and sneezing enables us to evaluate the deposition dose of aerosol particles in healthy individuals. For example, a person in a public place (e.g. supermarket or car park) can accumulate in the respiratory system up to 200 virus copies in 2 min time by breathing in virus laden aerosols. Wearing face mask considerably reduces the deposited load down to 2 virus copies per 2 min. The modelling also suggests that it should be possible to measure virus causing COVID-19 (SARS-CoV-2) within aerosol particles in hospitals and public places, e.g. care homes and supermarkets.

World is now experiencing a major health calamity due to the coronavirus disease (COVID-19) pandemic, caused by the severe acute respiratory syndrome coronavirus clade 2 (SARS-CoV- 2). The foremost challenge facing the scientific community is to explore the growth and transmission capability of the virus. Use of artificial intelligence (AI), such as, deep learning, in (i) rapid disease detection from x-ray/computerized tomography (CT)/ high-resolution computed tomography (HRCT) images, (ii) accurate prediction of the epidemic patterns and their saturation throughout the globe, (iii) identification of the epicenter in each country/state and forecasting the disease from social networking data, (iv) prediction of drug-protein interactions for repurposing the drugs, and (v) socio-economic impact and prediction of future relapses, has attracted much attention. In the present manuscript, we describe the role of various AI-based technologies for rapid and efficient detection from CT images complementing quantitative real time polymerase chain reaction (qRT-PCR) and immunodiagnostic assays. AI-based technologies to anticipate the current pandemic pattern, possibility of future relapses and socio-economic impact are also discussed. We inspect how the virus transmits depending on different factors, such as, population density and mobility among others. We depict how AI-based mobile app for contact tracing and surveys can prevent the transmission. A modified deep learning technique can assess affinity of the most probable drugs to treat COVID-19. Here a few effective antiviral drugs, such as, Geneticin, Avermectin B1, and Ancriviroc among others, have been reported with their appropriate validation from previous investigations.

Background: World Health Organization (WHO) declared that COVID-19 as a pandemic on March 11, 2020. There is sudden need of statistical modeling due to onset of COVID-19 pandemic across the world. But health planning and policy requirements the estimates of disease problem form clinical data. Objective: To predict recovery rate, cases load rate on the basis of cumulative confirmed Novel Corona virus (NCV) cases, recovered cases and deaths form COVID-19 in India. Methods: The reported COVID-19 cases in the country were obtained from website (https://datahub.io/core/covid-19#resource-covid-19_zip/). The cumulative NCV confirmed cases; recovery cases and deaths were used for estimating recovery rate, cases load rate and death rate till date 24 April 2020. Results: A total of 24530 NCV confirmed cases were reported nationwide in India on 24 April 2020. It is found that the recovery rate increased 22% and case load rate decreased 74%. Death rate is found to be very low 3%. The difference of cases load rate and recovery rate (delta) coincide at 50 % then NCV cases expected would be declined. Conclusion: The epidemic in the country was mainly caused by the importation of India. Lockdown as restricting the migration of population and decided to quarantine of population may greatly reduce the risk of continued spread of the epidemic in India. This study predicts that by 20 May 2020, the cases load rate lesser than recovery rate there after COVID-19 patients would be started to reducing.

This study was aimed to investigate the effect of capital structure on firms’ profitability with special emphasis on Ethiopian Large Private Manufacturing Firms using panel data of five consecutive years (2006/07-2010/11G.C). The secondary data sources (audited financial statements) have been collected from the randomly selected thirty three large private manufacturing firms in Ethiopia. Linear regression model has been employed to analyze the relationship between firms’ profitability and capital structure. Specifically, Random-effect Generalized Least Square of panel data regression model has been selected to empirically test the literature driven hypotheses. Finally, the findings of this study revealed that a significant positive relationship between firms’ profitability and total debt ratio which indicate firm’s capital structure.

Despite their limited spatial extent, freshwater ecosystems host remarkable biodiversity, including one third of all vertebrate species. This biodiversity is declining dramatically: globally, wetlands are vanishing three times faster than forests and freshwater vertebrate populations have fallen more than twice as steeply as terrestrial or marine populations. Threats to freshwater biodiversity are well- documented but co-ordinated action to reverse this decline is lacking. We present an Emergency Recovery Plan to “bend the curve” of freshwater biodiversity loss. Priorities for action include: 1) accelerating implementation of environmental flows, 2) improving water quality, 3) protecting and restoring critical habitats, 4) managing exploitation of freshwater species and riverine aggregates, 5) preventing and controlling non-native species invasions, and 6) safeguarding and restoring river connectivity. We recommend revised targets and indicators for the Convention on Biological Diversity and the Sustainable Development Goals, and investment in enabling conditions at national, river basin and local scales.

We show the tensor properties of joint probabilities on a Riemannian parametric manifold. Initially we develop a binary data matrix for parameter measurements of a large number of particles confining in a closed system in order to retrieve the joint probability densities of related parameters. By introducing a new generalized inner product as a multilinear operation on dual basis of parametric space, we extract the set of joint probabilities and prove them to meet contravariant tensor properties in a general Riemannian parametric space. We show these contravariant tensors reduce to classical ordinary partial derivatives definition in ordinary Euclidean parametric space. Finally we prove by a theorem that symmetrized iterative contravariant derivative of cumulative probability function on Riemannian manifold gives the set of joint probabilities in those manifold. We bring some examples for compatibility with physical tensors.

Publicly-funded scientists have a responsibility to engage with the public on scientific information, but are lacking a standardized framework and assessment strategy to do it well. The PEPS (Public Engagement Practices for Scientists) Method is an outcomes-centered framework employing standardized pedagogical methods with quantifiable outcomes. This approach reveals that scientists often have unrealistic expectations for achieving affective learning outcomes (i.e. changing views from anti- to pro-vaccine) by solely cognitive learning strategies (i.e. supplying data). The PEPS Method can serve as a roadmap for standardized science communication assessments, complementing existing science communication training programs for the next generation of scientists.

Background: The question of whether children are less likely to pass on SARS-CoV-2 is important for planning society’s response to the pandemic. A document available on the Charité hospital website has not been formally published but is frequently referred to as supporting the notion that viral loads are similar in children and adults. Methods: The summary data from this document was extracted and used to produce summary statistics for three age groups: younger children (ages up to 11), older children (ages 12 to 19) and adults (ages 20 and above). Viral loads between the two children’s groups and the adult group were compared using Welch’s t test, which only requires group means and standard deviations and which is robust against moderate departures from normality. Findings: Viral loads were significantly lower than in adults for both younger children (p=0.04) and older children (p=0.04). Overall, viral loads were lower in children than adults (p=0.005). Interpretation: For both younger and older children, on average those with detectable SARS-CoV-2 have significantly lower viral loads than adults. Funding: No funding was received for this analysis.

In this paper, quasi-static axial compression tests are performed on the nodal Moso bamboos to study the size effect on energy absorption of the bamboos and the damage pattern of the multiple bamboo columns. Experimental results show that under the same moisture content, growth age and growing environment, the specific energy absorption (SEA) of the test samples increases with the increase of the out-diameter and thickness of the bamboo columns, indicating that size effect exists for energy absorption of the Moso Bamboos. For the multiple bamboo columns, there are mainly three failure modes for the constituent single bamboo columns: splitting above the node, splitting below the node and splitting through the node. Also, the tensile tests are conducted on three kinds of dog-bone shaped bamboo samples to investigate the macroscopic tensile fracture mode in the longitudinal direction of Moso bamboos. Results show that there is no direct relationship between the fracture pattern and moisture content of the bamboos, as well as the growth age of the bamboos. However, the tensile loading rate and the shape of the dog-bone shaped bamboo sample could affect the macroscopic fracture pattern of the bamboos in some cases.

There is a skin allergy epidemic in the western world, and the rate of deterioration has increased significantly in the past 5-10 years. It is probable that there are many environmental contributing factors, yet some studies have linked it primarily to the rise in the use of synthetic chemical ingredients in modern cosmetics. Our challenge, therefore, was to find a mechanism to determine the effect these substances have on skin health, and whether they really are a primary cause of long term damage to the skin. The first problem is the lack of any definitive way to measure skin health. Motivated by the overwhelming evidence for a link between deficient gut flora and ill health, we decided to look at whether our skin microbiota could similarly be used as an indicator of skin health. Our research illustrates how it is microbiota diversity alone that can predict whether skin is healthy or not, after we revealed a complete lack of conclusive findings linking the presence or abundance of particular species of microbe to skin problems. This phenomenon is replicated throughout nature, where high biodiversity always leads to healthy ecosystems. ‘Caveman’ skin, untouched by modern civilisation, was far different to ‘western’ skin and displayed unprecedented levels of bacterial diversity. The less exposed communities were to western practices, the higher the skin diversity, which is clear evidence of an environmental factor in the developed world damaging skin. For the first time we propose benchmark values of diversity against which we can measure skin to determine how healthy it is. This gives us the ability to be able to predict which people are more likely to be prone to skin ailments, and start to test whether cosmetic ingredients and products are a main cause of the skin allergy epidemic.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

Globally, humans are struggling with the double threat of communicable and non-communicable diseases, which are presenting new challenges to public health. Public health problems are generally studied and addressed at primary, secondary and tertiary levels. Most effective results are seen with primary interventions. Public health is becoming more aware of the importance of environment-gene interactions in the ontology of health and disease using epigenetics. Epigenetics is the study of altered gene expression without change in base pairs. Be it physical, social, behavioral, or economic factors; they all influence quality of life and health of individuals and populations. That environments are changing the human health phenotype and these changed phenotypes are heritable is of concern for the future of the human race. Knowing the causes of non-communicable human diseases using epigenetics will contribute to the development of new policies to encourage prevention using primary public health initiatives. Research and application of epigenetics shows great promise for improving population health. Continued advances in epigenetics will enhance how we understand and address the way environments are affecting the human health phenotype. For some time, health systems have been and continue to be tertiary in nature. Epigenetic changes can provide information necessary to better understand how social determinants of health can be used to build societies focused on equitable health for all people, rather than continuing to focus on treatment of diseases in the tertiary phase that leads to health disparities. Understanding mechanisms of social determinants of disease, will allow society to evolve in a health-oriented rather than a disease-oriented world. For this reason, we must enhance and apply epigenetics (physical, social, behavioral, economic) research to policy development. We will discuss how bringing social determinants together with biology can be used as new tools for public health policy.

Concrete-filled steel columns have been extensively used in the world due to having all suitable characteristics of concrete and steel, more ductility, increasing concrete confinement using steel wall, large energy-absorption capacity and appropriate fire behavior. In present paper, concrete-filled steel square columns have been simulated under the influence of blast load using ABAQUS software. These responses will be compared for scaled distances based on the distance to source and weight of explosive material. As result, it can be seen that although concrete deformation has been restricted using steel tube, but inner layer of concrete has been seriously damaged and column displacement will be decreased by increasing scaled distance. We also concluded that concrete-filled steel columns have high ductility and blast resistance.

In this study, the probabilistic exergoeconomic analysis was performed for four industrial gas turbine (GT) units comprising of two (GT16 and GT19) units of 100MW GE engine and two (GT8 and GT12) units of 25MW Hitachi engine at Transcorp Power Limited, Ughelli. These four industrial GT engine units were modelled and simulated using natural gas as fuel. The design point (DP) simulation results of the modelled GT engines were validated with the available DP thermodynamic data from original equipment manufacturer (OEM). This was done before the off-design point (ODP) simulation was carried out which represents the plant operations. The results obtained from exergy analysis at full load operation show that the turbine has the highest exergy efficiency followed by compressor and combustion having the least. For turbines these were 96.13% for GT8 unit, 98.02% for GT12 unit, 96.26% for GT16 unit, and 96.30% for GT19 unit. Moreover, the combustion chamber has the highest exergy destruction efficiency of 55.16% GT8 unit, 56.58% GT12 unit, 43.90% GT16 unit, and 43.30% GT19 unit respectively. The exergy analysis results obtained from the four units show that the combustion chamber (CC) is the most significant exergy destruction with lowest exergy efficiency and highest exergy destruction efficiency of plant components. The exergoeconomic analysis results from four units showed combustion chamber energy destruction cost of 531.08 $/h GT8 unit, 584.53 $/h GT12 unit, 2351.81$/h GT16, and 2315.93$/h GT19 unit. The probabilistic results analysis based on the input parameters distributions evaluated and discussed.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

The SARS-CoV-2 virus that causes the COVID-19 disease has wreaked havoc on the world community in terms of every imaginable parameter. The research output on COVID-19 has been nothing short of phenomenal, especially in the medical and biomedical sciences, where the search for a potential vaccine is being conducted in earnest. Much of the advanced research has been distributed in the leading medical journals, including the Journal of the American Medical Association (JAMA), where the latest research is distributed on a daily basis. The purpose of this paper is to provide some perspectives on 44 interesting and highly topical research papers that have been published in JAMA, at the time of writing, within the past two weeks. The diverse topics include public health, general medicine, internal medicine, oncology, paediatrics, geriatrics, and biostatistics.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

An on-site, ultra-sensitive, and quantitative sensing method was developed based on quantum dot nanobeads (QDNBs) and test strip for the determination of total aflatoxins (AFTs) in rice and peanut. The monoclonal antibody against AFT (mAbAFT) was home-made and labeled with QDNB. After the pre-coating of the AFT antigen on the test line (T line), the competitive immunoreactions were conducted between AFT and AFT antigen on the T line with QDNBs-mAbAFT. Under optimal conditions, this approach allowed a rapid response towards AFT with a considerable sensitivity of 1.4 pg/mL and 2.9 pg/mL in rice and peanut matrices, respectively. The put-in and put-out duration were within 10 min. The recoveries for AFT in rice and peanut samples matrices were recorded from 86.25–118.0% with the relative deviations (RSD) below 12%. The assay was further validated via the comparison between this QDNB strip and the conventional HPLC method using spiked samples. Thus, the design provided a potential alternative for on-site, ultra-sensitive, and quantitative sensing of AFT that could also be expanded to other chemical contaminants for food safety.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

Mechanical properties of cardiomyocytes from different transmural regions are heterogeneous in the left ventricular wall. The cardiomyocyte mechanical environment affects this heterogeneity because of mechano-electric feedback mechanisms. In the present study, we investigated the effects of load upon transmural differences in contraction of subendocardial (ENDO) and subepicardial (EPI) single cells isolated from the murine left ventricle. Various loads were applied to the cells using carbon fiber techniques for single myocytes. To simulate experimentally obtained results and to predict mechanisms underlying the cellular response to change in load, our mathematical models of the ENDO and EPI cells were used. Extent of the transmural gradient in the time course of contractions was independent of the loading conditions where unloaded and heavy loaded (isometric) contractions were examined, but the regional gradient of the relaxation time characteristics tended to decrease when the load decreased. Under auxotonic contractions, time to peak contraction (T_max) was significantly longer in ENDO cells than in EPI cells at low preload. An increase in preload (axial stretch) prolonged T_max in both cell types; however, the prolongation was greater in EPI cells, resulting in a decrease in transmural gradient in T_max at high preload. The [Ca²⁺]_i transient decay time constant was consistent with the greater preload dependency in T_max of EPI cells. Our modified mathematical models reproduced experimental results, suggesting that differences in cooperativity of cross bridges and calcium troponin C complex interactions between the ENDO and EPI cardiomyocytes may contribute to the different cellular responses to stretch, which may provide a decrease in transmural dispersion of cellular shortening in the intact heart.

After a local pollution control plant significantly reduced phosphorus loading into a phytoplankton-dominated tributary of the Potomac River in the early 1980’s, water quality and biological communities were monitored bi-weekly from April-September. After a 10-year time-lag, submerged aquatic vegetation (SAV), once abundant in this freshwater tidal embayment, returned to the area in 1993. After additional reductions in nitrogen load starting in 2000, the system completely switched to a SAV-dominated state in 2005. Fish abundance didn’t change during these distinct phase changes, but the fish community structure did. Increases in SAV provided refuge and additional spawning substrate for species with adhesive eggs such as Banded Killifish (Fundulus diaphanus), which is now the most abundant species in the embayment. Other changes seen were a decrease in the relative contribution of open water dwelling species such as White Perch (Morone americana), and an increase of visual predators such as Largemouth Bass (Micropterus salmoides). The 30-year record of data from this Potomac River tributary has revealed many important long-term trends that validate the effectiveness of initiatives to improve water treatment, and will aid in the continued management of the watershed and point source inputs.

Collision avoidance is an important feature in advanced driver-assistance systems, aiming at providing correct, timely and reliable warnings before an imminent collision (objects, vehicles, pedestrians, etc.). A co-simulation framework is proposed in this paper to address the design and evaluation of collision avoidances in a cyber-physical system. The co-simulation framework is supported on the interaction between SCANeR and Matlab/Simulink. From the best of authors’ knowledge, two main contributions are reported in this paper. Firstly, the modelling and simulation of virtual on-chip LIDAR sensors in a cyber-physical system (CPS) considering traffic scenarios is presented. The CPS is designed and implemented in SCANeR. Secondly, an obstacle recognition library with three specific Artificial Intelligence-based methods is also designed based on sensory information database provided by SCANeR. Three methods for collision avoidance detection are considered, i.e.; a multi-layer perceptron neural network, a self-organization map and a support vector machine. Finally, a comparison among these methods for detecting obstacles before different weather conditions is done with very promising results in terms of accuracy. The best results are achieved using the multi-layer perceptron in sunny and fog conditions, the support vector machine in rainy and self-organized map in snowy conditions.

Distribution systems can form islands when faults occur. Each island represents a subsection with variable boundaries subject to the location of a fault(s) in the system. A subsection with variable boundaries is referred to as island in this paper. For operation in autonomous mode, it is imperative to detect the island configurations and stabilize these subsections. This paper presents a novel scheme for the detection of islanding boundaries and stabilizing the system during autonomous operation. In the first stage, a boundary detection method is proposed to detect the configuration of the island. In the second stage a dynamic voltage sensitivity factor (DVSF) is proposed to assess the dynamic performance of the system. In the third stage, a wide area load shedding program is adopted based on DVSF to shed the load in weak busbars and stabilize the system. The proposed scheme is validated and tested on a generic 18-bus system using a combination of EMTDC/PSCAD and MATLAB softwares.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

Increased access to highly active antiretroviral therapy (HAART) by HIV⁺ individuals has become a reality worldwide. In Brazil, ART currently reaches over half of the HIV-infected subjects. In the context of a remarkable HIV-1 genetic variability, highly related variants, called quasispecies, are generated. HIV quasispecies generated during infection can influence virus persistence and pathogenicity, representing a challenge to treatment. However, the clinical relevance of minority quasispecies is still uncertain. For this study, we have determined the archived proviral sequences, viral subtype and drug resistance mutations from a cohort of HIV⁺ patients with undetectable viral load undergoing HAART as first-line therapy using next-generation sequencing for near full-length virus genome (NFLG) assembly. HIV-1 consensus sequences representing NFLG were obtained for eleven patients, while for another twelve varying genome coverage rates were obtained. Phylogenetic analysis showed the predominance of subtype B (83%; 19/23). Considering the minority variants, 18 patients carried archived virus harboring at least one mutation conferring antiretroviral resistance; for six patients, the mutations correlated with the current ARVs used. These data highlight the importance of monitoring HIV minority drug resistant variants and their clinical impact, to guide future regimen switches and improve HIV treatment success.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Macrobrachium rosenbergii is a valuable freshwater prawn in Asian aquaculture. In recent years, a new symptom that was generally called as ‘white head’ caused high mortality in M. rosenbergii farms in China. Samples of M. rosenbergii, M. nipponense, Procambarus clarkii, M. superbum, Penaeus vannamei, and Cladocera from a farm suffering from ‘white head’ in Jiangsu Province were collected and analyzed in this study. Pathogen detection showed that all samples were positive for Shrimp hemocyte iridescent virus (SHIV). Histopathological examination revealed dark eosinophilic inclusions and pyknosis in hematopoietic tissue, hepatopancreas and gills of M. rosenbergii and M. nipponense. Blue signals of in situ DIG-labeled LAMP (ISDL) appeared in hematopoietic tissue, hemocytes, hepatopancreatic sinus, and antennal gland. TEM of ultrathin sections showed a large number of SHIV particles with a mean diameter about 157.9 nm. The virogenic stromata and budding virions were observed in hematopoietic cells. Quantitative detection by TaqMan probe based real-time PCR of different tissues in natural infected M. rosenbergii showed that hematopoietic tissue contained the highest SHIV load with a relative abundance of (25.4±16.9)%. Hepatopancreas and muscle contained the lowest SHIV load with a relative abundance at (2.44±1.24)% and (2.44±2.16)%, respectively. Above results verified that SHIV is the pathogen causing ‘white head’ in M. rosenbergii, and M. nipponense and Pr. clarkii are also the susceptible species of SHIV.

Identifying appropriate animal models is critical in developing translatable in vitro and in vivo systems for therapeutic development and investigating disease pathophysiology. These animal models should have direct biological and translational relevance to the underlying disease they are supposed to mimic. Aging dogs naturally develop a cognitive decline in many aspects including learning and memory, but also exhibit human-like individual variability in the aging process. Neurodegenerative processes that can be observed in both human and canine brains include the progressive accumulation of β-amyloid (Aβ) found as diffuse plaques in the prefrontal cortex, including the gyrus proreus, the hippocampus, and in the cerebral vasculature. A growing body of epidemiological data shows that human patients with neurodegenerative diseases have concurrent intestinal lesions, and histopathological changes in the gastrointestinal (GI) tract occurs decades that evolve before neurodegenerative changes. Gut microbiome alterations also have been observed in many neurodegenerative diseases including Alzheimer’s and Parkinson’s diseases, and inflammatory CNS diseases. Interestingly, only recently has the dog gut microbiome been recognized to more closely resemble in composition and in functional overlap with the human gut microbiome as compared to rodent models. This article aims to review the physiology of the gut-brain axis (GBA), and its involvement with neurodegenerative diseases in dogs and humans. Additionally, we outline the advantages and disadvantages of traditional in vitro and in vivo models and discuss future research directions investigating major human neurodegenerative diseases such as Alzheimer’s and Parkinson’s diseases using dogs.

To implement renewable energy resources, microgrid systems have been adopted and developed into the technology of choice to assure mass electrification in the next decade. Microgrid systems have a number of advantages over the conventional utility grid systems, however, it faces severe instability issues due to continually increasing constant power loads. To improve the stability of the entire system, load side compensation technique is chosen because of its robustness and cost effectiveness. In this particular occasion, a sliding mode controller is developed for microgrid system in the presence of CPL to assure certain control objective of keeping the output voltage constant at 480V. After that, the robustness analysis of the sliding mode controller against parametric uncertainties is presented. The sliding mode controller robustness against parametric uncertainties, frequency variations, and additive white Gaussian noise (AWGN) are illustrated in this paper. Later, the performance of the PID and sliding Mode controller is compared in case of nonlinearity, parameter uncertainties, and noise rejection to justify the selection of Sliding Mode controller over PID controller. All the necessary calculations are reckoned mathematically and results are verified in the virtual platform such as MATLAB/Simulink with the appreciable outcome.

The variations in socioeconomic status (SES) between different social classes of a population correspond to differences in accessibility to all resources available and able to improve global health. SES can influence global health trajectory for an individual or a community, depending if SES is low or high. Sleep is sensitive to environmental stimuli, as well as living conditions. Plenty of studies linked sleep complaints with mood disorders, allostatic load or circadian disruption; but very few or none investigated deeply what happened earlier to sleep depending of SES. While SES is now known as one of the main determinants for a good health and a good aging, its influence on sleep disorders (SD) is not well understood. SES is a concept, not directly observable but estimated using indicators like income, education, occupational status and area of living. Even if recent evidence suggested that few of SES indicators like occupational status are linked with sleep disturbances, the relation between SES and health in general with sleep as an outcome or a mediator is not well documented. This scoping review synthetized studies which investigated physiological and psychological mechanisms resulting from a low SES and linked them with sleep disturbances as consequences or as mediators. This review also explore a possible role played by sleep in the relation between socioeconomic status and health inequalities.

The objective of this work was to investigate the use of remotely sensed vegetation indices to improve the quality of yield maps. The method was applied to the yield data of twelve cornfields from the Data Intensive Farm Management project. The results revealed the need to time shift the yield values up to three seconds to better match the sensor readings with the geographic coordinates. The residuals of the yield prediction model were used to identify points with unlikely yield values for that location, as an alternative to traditional approaches using local spatial statistics, without any assumption of spatial dependence or stationarity. The temporal and spatial distribution of the standardized coefficients for each experimental unit highlighted the presence of trends in the data. At least five out of the twelve fields presented trends that could have been induced by data collection.

In the current study, the failure behavior of retrofitted steel structures was studied experimentally and theoretically with steel/CFRP double strap joints (DSJs) under quasi-static tensile loading. A series of DSJs with different bonding lengths are also considered and examined to experimentally assess the effective bond length. To predict the failure load values of the tested specimens, a new stress-based criterion, namely the point stress (PS) criterion is proposed. Although some theoretical predictive modelling for the strength between steel/CFRP joints under various loading conditions has been presented, in this work by using the new proposed approach, one can calculate rapidly and conveniently the failure loads of the steel/CFRP specimens. Furthermore, to assess the validity of the new proposed criterion, further experimental data on steel/CFRP DSJs available in the open literature are predicted using the PS criterion. Finally, it was found that a good agreement exists between the experimental results and the theoretical predictions based on the PS criterion.

Cropland area per capita and pressure index on cropland is the important parameters measuring the social vulnerability and sustainability in the perspective of food security in a certain region in China during the historical periods. This study reconstructs the spatial distribution change of cropland area per labor/household and pressure index on cropland during the 17th-20th century by the methods of historical documents, regression analysis, pressure index model and GIS. Then it analyzed the impacting process of climate change and sustainability of cropland use during the different periods. It draws conclusions: (i) the spatial difference of labor/household density was obvious which had the same pattern as cropland distribution during the same periods, which is higher density in three agricultural areas. (ii) Cropland area per capita was relatively higher during the 17th-18th century, which were above 0.4 ha/person in majority counties and distributed homogenously. Till the 19th century and the beginning of 20th century, cropland area per capita in large amount of regions decreased below 0.2 ha/person embodying the increase of social vulnerability and unsustainability at that time. (iii) Pressure index on cropland also showed the similar spatial pattern as cropland area per capita which presented lower threshold than nowadays. During the 17th-18th century there was no pressure on cropland. While, in the 19th century and at the beginning of 20th century, two high value centers of pressure index on cropland appeared in Middle Shandong and the Jiaodong region, pressure on sustainable cropland use increased obviously and a food crisis is probably created. (iv) Higher sustainable extent of cropland use corresponds to cold period, and lower sustainable extent of cropland use corresponds to warm period in Shandong over the past 300 years. The turning point of 1680s from dry to wet attributes to the decrease of sustainable extent of cropland use in Shandong not very distinctively. More and more pressure on sustainability of cropland use finally since the beginning of 20th century would intensify the social conflict and increase the probability of social revolts.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

Sleep disorders (SD) have a complex aetiology, and socioeconomic status (SES) as determined by social class, household income, ethnicity and education plays an important role in their development. As SD are associated with cognitive impairment and mood disorders, they in turn impact SES. Socioeconomic status also influences allostatic load caused by chronic accumulation of stress throughout life. Environmental and psychological stressors have a direct effect on SD, and they are modulated by SES, in combination with comorbidities like obesity and cardiovascular disease. This review explores the recent theories about the influence of SES on the development of SD in the general population, whether or not occurring with comorbidities, and also focusses on the interplay between socioeconomic status, circadian rhythms, aging and clinical outcomes like metabolic diseases and cancer.

ABSTRACT Ethiopia is a developing country, where majority of the population lives in rural areas without access to electricity. 83% of the total population of the country use traditional biomass energy as a basic source of energy. In contrast, the country is endowed with sufficient renewable energy resources which can be used as a standalone electric energy supply system for electrifying remote areas of the country. These resources are mainly micro hydropower and wind which can be used individually or the best combination of one another. The application of hybrid renewable energy system has become an important alternative solution for rural electrification program. The Modeling and control of a hybrid PV-Wind-Hydro DG system is also addressed. Dynamic models for the major system components, namely, wind energy conversion system, PV energy conversion system, hydro, inverter, and overall fuzzy logic controller units are developed. Then, a simulation model for the proposed hybrid power system has been developed using MATLAB /Simulink environment. This is done by creating subsystem sets of the major dynamic component models and then assembling into a single aggregate model. The overall power management strategy for coordinating and/or controlling the different energy sources is also presented in the thesis work. Generally there are 800 households with total electric demand of 71.6KW.To satisfy this demand 52%, 35% and 13% is to be contributed from wind/hydro/solar respectively. To use the power economically fuzzy logic controller is used. The controller monitors the demand and the available sources and then switches to the appropriate power supply according to the written rules. Simulations have been carried out to verify the system dynamic performance using a practical load profile and weather data. The result shows that the overall power management strategy is effective and the load demand is balanced. To complete this work, a grid extension from the closest substation has been compared with hybrid system. Cost of the grid extension is estimated based on the data obtained from EEP office. This is done in order to compare the cost of the designed hybrid power system against the cost of grid extension. The result shows that breakeven grid extension distance to be 23.9km which indicates that grid extension is preferable.

With large-scale distributed generators (DGs) in an active distribution network (ADN), conventional load flow convergence failure is incurred by heavy power transmission. The Holomorphic Embedding Load Flow Method (HELM) has proven to be more robust than the Newton–Raphson method under heavy power transmission. At present, HELM is mainly designed for balanced transmission networks. In this study, we developed a three-phase HELM model to accommodate DGs, delta connection loads, and ZIP loads for ADN. The effectiveness and better performance of the proposed method under heavy load situations were validated using modified unbalanced IEEE 13, 34, 37, and 123 test feeders.

Emergency control load-shedding is a key solution to prevent blackouts in the power system. This paper proposed a new model of emergency controls load shedding based on the fast identification of the unstable state of the power system. K-means clustering algorithm divided the instability mode into the clusters. The results of analysis of this cluster were used as the basis for classification control. Building load shedding strategies is consisted of the pre-designed rules based on AHP algorithm. When the recognition of the power system “instability” is detected, the signal of load shedding control is triggered immediately, therefore the decision time is greatly shortened comparing to the traditional methods. The effectiveness of the proposed method was tested on the IEEE 39-bus to overcome the limitations of the last traditional methods.

Human-Computer Interaction, including technology-aided instruction, is beginning to focus on virtual reality (VR) technology due to its ability to support immersive learning, teaching through simulation, and gamification of learning. These systems can deliver high-level multisensory learning experiences that are important in the teaching of many subjects, especially those involving abstract concepts or requiring spatial skills, such as organic chemistry. Haptic experiences with VR, however, remain a challenge. In addition, development have focused on general entertainment/gaming; VR systems in chemistry implement simulations of the chemistry laboratory and other advanced systems whereas those that support safe, game-like, immersive and multisensory learning of organic chemistry with haptics at pre-university education levels are scarce. We developed the VR Multisensory Classroom (VRMC) as an immersive learning environment within a VR head-mounted display, where learners employ hand movements to build hydrocarbon molecules and experience haptic feedback through gloves with built-in sensors and hand-tracking with the Leap Motion system. We report here the evaluation of the first prototype by learners from diverse backgrounds who reported on the ability of the VRMC to support high engagement, motivation, interest and organic chemistry learning as well as diverse learning styles. The VRMC is a novel VR classroom that supports immersive learning in molecular organic chemistry with haptics for multisensory learning.

Besides the Lagrangian and the Eulerian descriptions, the motion of a body can also be expressed relative to the present configuration of the body, known as the relative motion description. It is interesting to consider such a relative motion description in general to formulate the basic system of field equations for solid bodies. In doing so, when the time increment from the present state is small enough, the nonlinear constitutive equations can be linearized relative to the present state so that the resulting system becomes linear. This will be done for thermoelastic materials with a brief comment on the exploitation of entropy principle in general. Relative Lagrangian formulation is based on the well-known ``small-on-large'' idea, and can be implemented for solving problems with large deformation in successive incremental manner. Some applications of such a formulation in numerical simulations are briefly reviewed.

Background: Schizophrenia is a severe psychiatric disorder that has a large impact on patients’ lives. In addition to Western medicine, the use of additional treatments, such as acupuncture, in treating the positive, negative, and cognitive symptoms is increasing. Methods: We conducted a systematic review on the use of acupuncture as an add-on treatment for patients with schizophrenia that are in regular care, with a special focus on the treatment of the often accompanying co-morbid sleep disorders. In this study, we searched the Medline, ScienceDirect, Cochrane Library, Scopus, and ERIC databases with a cut-off date of December 31, 2017, thereby following the guidelines of the Preferred Reporting Items for Systematic Reviews and Meta-analysis (PRISMA) protocol. Results: Our search resulted in 26 eligible studies. Most studies showed limited evidence for the use of acupuncture as add-on therapy in the treatment of clinical symptoms, but beneficial effects have been reported in the treatment of co-morbid sleep disorders. Conclusions: Limited evidence was found for the use of acupuncture as add-on therapy in the treatment of patients with schizophrenia; however, positive results were found in the treatment of sleep disorders, but this result needs to be confirmed in large, randomized, controlled trials.

In this paper, a recent meta-heuristic optimization algorithm called the discrete-continuous hyper-spherical search algorithm is used to solve the mixed-integer nonlinear problem of soft open points (SOPs) and renewable distributed generators allocation along with new network reconfiguration methodology under different loading conditions to minimize the total power loss in balanced distribution systems. Multi-scenario studies, which aim to improve the investigation of the overall performance of the strategies, are conducted on IEEE 33-node and 83-node balanced distribution systems. The contributions of SOP losses to the total active losses, as well as the effect of increasing the number of SOPs connected to the system, are investigated to determine the real benefits gained from their allocation. The results obtained validate, with proper justifications, the effectiveness of allocating both SOPs and renewable distributed generators with the proposed network reconfiguration methodology to provide the best operation of distribution networks with minimum losses and enhanced power quality performance. It was also shown that SOPs successfully assist the growing integration plans of the renewable distributed generators units and can address issues related to voltage violations and network losses efficiently.

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

This is a quantitative research based on secondary sources of data. The study examines the influence of Chief Executive Officer’s (CEO) compensation on a firm's performance. The objectives of the study were to determine if CEO compensation and firm size do significantly influence a firm’s performance. In other to elicit information to examine the relationship between the variables, the convenience sampling technique, with the combination of both the cross-sectional and time-series data (panel data) were used since they provide greater precision and guard against having an illusory sample. 10 banks quoted on the Nigerian Stock Exchange were sampled for easy accessibility of data. The least square regression technique was used to test the hypotheses of the study. Two hypotheses were tested using panel least square (EViews 8) and from the research work, we summarize the following results; there is a significant relationship between CEO compensation and firm performance in the Nigerian banking industry. In addition, firm size does significantly influence firm performance in the Nigerian banking industry. The study recommends that there should be proper compensation review as this will increase the productivity of the executives. Since increased pay is necessary for the efficiency of the workers, it is advised to ensure a considerable pay as this will ensure for efficiency in the organization. In addition, since the core goal of setting up any business is to make a profit, business organisations should sort out ways at maximising profit and this could include cutting down expenses such as cutting down excessive employees’ pay (CEOs pay especially) and setting apposite pay package for employees. Therefore, policymakers (board of directors) should make an effort to align CEO’s paywith the firm’s capability to pay.

A fluid power industry powering the agricultural machinery faces big challenges nowadays. An issue of energy saving has become important due to increasing fuel costs and more stringent emissions regulations impacting vehicle development. A recent study conducted by the U.S. Department of Energy shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications and create innovative solutions. To increase energy efficiency of fluid power systems reduction of throttling losses and potential energy recovery strategies are needed. Aim of this work is to present classification of current energy saving architectures and aid the development of new techniques for mobile fluid power machines.

Blade Health Monitoring (BHM) is often necessary in power plants and in aviation to prevent excessive blade vibration and cracks. This article proposes a network of blade tip timing sensors operated in a distributed BHM system. A number of cooperating agents is implemented in smart conditioning units which can autonomously operate in an adverse environment and communicate with other nodes via a serial interface. The project uses special versions of reduced instruction set chips that are able to operate near the hot section of the engine. Due to the limited number of types of microprocessors available in the extended temperature range grading, it was necessary to fully utilize the limited hardware resources and implement preemptive multitasking. For this purpose, a custom operating system and communication protocol were designed. The protocol hosts the middle layer which hides the implementation of the distributed system. The presented architecture ensures the sufficient computational capacity in individual nodes of the network operated in adverse conditions. It is scalable and resistant to transmission errors.

Load balancing, energy efficiency and fault tolerance are among the most important data dissemination issues in Wireless Sensor Networks (WSNs). In order to successfully cope with the mentioned issues, two main approaches (namely, Data-centric Storage and Distributed Data Storage) have been proposed in the literature. Both approaches suffer from data loss due to memory and/or energy depletion in the storage nodes. Even though several techniques have been proposed so far to overcome the mentioned problems, the proposed solutions typically focus on one issue at a time. In this paper, we integrate the Data-centric Storage (DCS) features into Distributed Data Storage (DDS) mechanisms and present a novel approach, denoted as Collaborative Memory and Energy Management (CoMEM), to overcome both problems and bring memory and energy efficiency to the data loss mechanism of WSNs. We also propose analytical and simulation frameworks for performance evaluation. Our results show that the proposed method outperforms existing approaches in various WSN scenarios.

Increasing and prolonged droughts have become a feature of the South African environmental landscape. This article investigates the sustainability of water procurement to the rural town of Beaufort West and the reasons for the town’s water provision crises during the droughts of 2009-2011 and 2017-2019. Innovative solutions were reached to alleviate the serious water-shortages during these droughts. Data to illustrate population increases and precipitation decreases, which impacted on the town’s water resources, was collected from census records of Statistics South Africa and from the Department of Water and Sanitation, respectively. A number of risk factors contributed to the town’s water crises, e.g. unsustainable water extraction at times of serious droughts, poor water monitoring, metering and attention to leakages, an expansion of informal settlements within the municipal boundaries of Beaufort West, as well as annual rainfall patterns that became increasingly unpredictable. The article concludes that water resource development had not kept pace with demand, therefore water infrastructure should be built with enough capacity to cope with regular dry periods. Equilibrium should be reached between the water expectations of the community and water availability to avoid future social instability in water-stressed towns such as Beaufort West.

The illegal use of explosives by terrorists and other criminals is an increasing issue in public spaces, such as airports, railway stations, highways, sports arenas, theaters, and other large buildings. Security in these environments can be achieved by a set of different means, including the installation of scanners and other analytical devices to detect ultra-small traces of explosives in a very short time-frame to be able to take action as early as possible to prevent the detonation of such devices. Unfortunately, an ideal explosive detection system still does not exist, which means that a compromise is needed in practice. Most detection devices lack the extreme analytical sensitivity, which is nevertheless necessary due to the low vapor pressure of nearly all explosives. In addition, the rate of false positives needs to be virtually zero, which is also very difficult to achieve. Here we present an immunosensor system based on kinetic competition, which is known to be very fast and may even overcome affinity limitation, which impairs the performance of many traditional competitive assays. This immunosensor consists of a monolithic glass column with a vast excess of immobilized hapten, which traps the fluorescently labeled antibody as long as no explosive is present. In the case of TNT occurring, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled CMOS camera. Liquid handling is performed with high-precision syringe pumps and chip-based mixing-devices and flow-cells. The system achieved limits of detection of 1 pM (1 ppt) of the fluorescent label and around 100 pM (20 ppt) of the explosive 2,4,6-trinitrotoluene (TNT). The total assay time is less than 8 min. A cross-reactivity test with 5000 pM solutions showed no signal by PETN, RDX, and HMX. This immunosensor belongs to the most sensitive and fastest detectors for TNT with no significant cross-reactivity by non-related compounds.

Since its inception in the late 2000s, blockchain has emerged as a powerful tool for creating trust without intermediaries to incentivize global communities for working for a common goal, such as the improvement of its very ecosystem, its applications and community adoption. While first blockchains were mainly devised for confirming transactions of their innate cryptocurrencies like Bitcoin, smart-contract blockchains like Ethereum can interface with the real-world through so-called “oracles”, which feed trustful off-chain information. This paper introduces digital twins of physical objects and processes as computational oracles to effectively unleash the tremendous opportunity offered by blockchain to the realm of fundamental science, research and technology development (RTD). The crowdsourcing concept is illustrated with the example of centrifugal flow control in microfluidic “Lab-on-a-Disc” (LoaD) systems.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

In this work we identify combinations of technological activities that signal the presence local capabilities in a country to successfully export a product. We use country-level patent and trade data to generate a multi-layer network, and we apply maximization of entropy to generate synthetic data to effectively divide signal from noise. We show that in several sectors the signal far exceed the noise. Our exercise provides robust evidence of the presence of synergies between technologies to explain trade performances in specific markets. This can be highly useful for policy makers, to inform industrial and innovation policies.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

Molecular autism research is evolving towards a biopsychosocial framework that is more informed by autistic experiences. In this context, research aims are moving away from correcting external autistic behaviors and towards alleviating internal distress. Autism Spectrum Conditions (ASCs) are associated with high rates of depression, suicidality and other comorbid psychopathologies, but this relationship is poorly understood. Here, we integrate emerging characterizations of internal autistic experiences within a molecular framework to yield insight into the prevalence of psychopathology in ASC. We demonstrate that descriptions of social camouflaging and autistic burnout resonate closely with the accepted definitions for early life stress (ELS) and chronic adolescent stress (CAS). We propose that social camouflaging could be considered a distinct form of CAS that contributes to allostatic overload, culminating in a pathophysiological state that is experienced as autistic burnout. Autistic burnout is thought to contribute to psychopathology via psychological and physiological mechanisms, but these remain largely unexplored by molecular researchers. Building on converging fields in molecular neuroscience, we discuss the substantial evidence implicating mitochondrial dysfunction in ASC to propose a novel role for mitochondrial allostatic load in the relationship between autism and psychopathology. An interplay between mitochondrial, neuroimmune and neuroendocrine signaling is increasingly implicated in stress-related psychopathologies, and these molecular players are also associated with neurodevelopmental, neurophysiological and neurochemical aspects of ASC etiology. Together, this suggests an increased exposure and underlying molecular susceptibility to ELS that increases the risk of psychopathology in ASC. This article describes an integrative framework shaped by autistic experiences that highlights novel avenues for molecular research into mechanisms that directly affect the quality of life and well-being of autistic individuals. Moreover, this framework emphasizes the need for increased access to diagnoses, accommodations, and resources to improve mental health outcomes in autism.

The investigation of the electromagnetic properties of biological particles in microfluidic platforms may enable wireless monitoring and interaction with functional activity of microorganisms. Of high relevance is the membrane potential as it is one of the most important parameters of living cells. In particular, the complex mechanisms of the cell’s membrane potential are comparable to the dynamics of bacteria membranes, providing a simplified platform for advancing the current techniques and knowledge of general bio-particle dynamics. In this work, we provide a theoretical analysis and experimental results on the microwave detection of bacteria on a microfluidic-based framework for sensing the membrane potential of bacteria. The results enable to further advance the state-of-the-art of electromagnetic bacteria sensing and microfluidic control, and their implication for measuring and interacting with the cell and its membrane potentials, which is of great importance for developing new biotechnological engineered systems and solutions.

This paper aims to describe the geometrical structure and explicit expressions of family of finitely parametrized probability densities over smooth manifold $M$. The geometry of family of probability densities on $M$ are inherited from probability densities on Euclidean spaces $\left\{U_\alpha \right\}$ via bundle morphisms, induced by an orientation-preserving diffeomorphisms $\rho_\alpha:U_\alpha \rightarrow M$. Current literature inherits densities on $M$ from tangent spaces via Riemannian exponential map $\exp: T_x M \rightarrow M$; densities on $M$ are defined locally on region where the exponential map is a diffeomorphism. We generalize this approach with an arbitrary orientation-preserving bundle morphism; we show that the dualistic geometry of family of densities on $U_\alpha$ can be inherited to family of densities on $M$. Furthermore, we provide explicit expressions for parametrized probability densities on $\rho_\alpha(U_\alpha) \subset M$. Finally, using the component densities on $\rho_\alpha(U_\alpha)$, we construct parametrized mixture densities on totally bounded subsets of $M$. We provide a description of inherited mixture product dualistic geometry of the family of mixture densities.

Magnetic nanoparticles are met across many biological species ranging from magnetosensitive bacteria, fishes, bees, bats, rats, birds, to humans. They can be both of biogenetic origin and due to environmental contamination, being either in paramagnetic or ferromagnetic state. The energy of such naturally occurring single-domain magnetic nanoparticles can reach up to 10-20 room k_BT in the magnetic field of the Earth, which naturally led to supposition that they can serve as sensory elements in various animals. This work explores within a stochastic modeling framework a fascinating hypothesis of magnetosensitive ion channels with magnetic nanoparticles serving as sensory elements, especially, how realistic it is given a highly dissipative viscoelastic interior of living cells and typical sizes of nanoparticles possibly involved.

We introduce a modelling framework for the investigation of on-line machine learning processes in non-stationary environments. We exemplify the approach in terms of two specific model situations: In the first, we consider the learning of a classification scheme from clustered data by means of prototype-based Learning Vector Quantization (LVQ). In the second, we study the training of layered neural networks with sigmoidal activations for the purpose of regression. In both cases, the target, i.e. the classification or regression scheme, is considered to change continuously while the system is trained from a stream of labeled data. We extend and apply methods borrowed from statistical physics which have been used frequently for the exact description of training dynamics in stationary environments. Extensions of the approach allow for the computation of typical learning curves in the presence of concept drift in a variety of model situations. First results are presented and discussed for stochastic drift processes in classification and regression problems. They indicate that LVQ is capable of tracking a classification scheme under drift to a non-trivial extent. Furthermore, we show that concept drift can cause the persistence of sub-optimal plateau states in gradient based training of layered neural networks for regression.

Sometimes a pavement deflects only because of seasonal volume change of expansive soils in the pavement subgrade. Engineering practitioners expect an implementable and straightforward analysis method for a geosynthetic-reinforced pavement subjected to the swelling/shrinkage issue of expansive clayey subgrade, in an effort to find the bending moment, shear force and tension force distributions through the reinforced pavement, which are induced from the volumetric changes of subgrade soils. The virtual load method (VLM) was proposed in the past following the Timoshenko beam theory to analyze geosynthetic-reinforced pavement on expansive soils. In the VLM, the unknown virtual distributed load was obtained in the way by applying the inverse theory for the identification of material parameters of the pavement-foundation system. It was seen that the selection of the number of material parameters to obtain virtual load significantly affects the accuracy of the structural properties of the pavement and tensile properties of the geosynthetics if the linear least square method is used. In this paper, a unique numerical scheme was proposed in the hopes of solving the issue. After a forward problem was solved numerically, the Timoshenko beam deflection was taken as a start-up for the inverse problem to back analyze the load applied to the pavement. Solutions from forward/backward examples have explicitly shown the accuracy achieved related to the bending moment in the pavement and tension in the geosynthetic reinforcements. The proposed methodology can be applied for an in-depth understanding of the geosynthetic function for the mitigation of longitudinal cracks on pavements caused by heave/shrinkage of expansive soils.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

The ongoing revolution in Deep Learning is redefining the nature of computing that is driven by the increasing amount of pattern classification and cognitive tasks. Specialized digital hardware for deep learning still holds its predominance due to the flexibility offered by the software implementation and maturity of algorithms. However, it is being increasingly desired that cognitive computing occurs at the edge, i.e. on hand-held devices that are energy constrained, which is energy prohibitive when employing digital von Neumann architectures. Recent explorations in digital neuromorphic hardware have shown promise, but offer low neurosynaptic density needed for scaling to applications such as intelligent cognitive assistants (ICA). Large-scale integration of nanoscale emerging memory devices with Complementary Metal Oxide Semiconductor (CMOS) mixed-signal integrated circuits can herald a new generation of Neuromorphic computers that will transcend the von Neumann bottleneck for cognitive computing tasks. Such hybrid Neuromorphic System-on-a-chip (NeuSoC) architectures promise machine learning capability at chip-scale form factor, and several orders of magnitude improvement in energy efficiency. Practical demonstration of such architectures has been limited as performance of emerging memory devices falls short of the expected behavior from the idealized memristor-based analog synapses, or weights, and novel machine learning algorithms are needed to take advantage of the device behavior. In this work, we review the challenges involved and present a pathway to realize ultra-low-power mixed-signal NeuSoC, from device arrays and circuits to spike-based deep learning algorithms, with ‘brain-like’ energy-efficiency.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

Novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) variants of concern (VOC) are constantly threatening global public health. With no end date, the pandemic still persists with the emergence of novel variants that threaten the effectiveness of diagnostic tests and vaccines. Mutations in the Spike surface protein of the virus are regularly observed in the new variants, potentializing the emergence of novel viruses with different tropism from the current ones, which may change the severity and symptoms of the disease. Growing evidence has shown that mutations are being selected in favor of variants that are more capable of evading the action of neutralizing antibodies. In this context, the most important factor guiding the evolution of SARS-CoV-2 is its interaction with the host’s immune system. Thus, as current vaccines cannot block the transmission of the virus, measures complementary to vaccination, such as the use of masks, hand hygiene, and keeping environments ventilated remain essential to delay the emergence of new variants. Importantly, in addition to the involvement of the immune system in the evolution of the virus, we highlight several chemical parameters that influence the molecular interactions between viruses and host cells during invasion and are also critical tools making novel variants more transmissible. In this review, we dissect the impacts of the Spike mutations on biological parameters such as (1) increase of Spike binding affinity to hACE2; (2) bound time for the receptor to be cleaved by the proteases; (3) how mutations associate with increase of RBD up-conformation state in the Spike ectodomain; (4) expansion of uncleaved Spike protein in the virion particles; (5) increment of Spike concentration per virion particles; and (6) evasion of the immune system. These factors play key roles in the fast spreading of SARS-CoV-2 variants of concern, including the Omicron.

The air is not the same as thousands and hundreds of years ago. In the air, suspended particles originate from natural phenomena like dust storms or volcanic activities, as well as anthropogenic pollutants such as fuel engine exhaust and everyday activities at home. The total particles in the air can be classified by sizes, such as PM10, PM2.5 or ultrafine particles. However, there are many other important factors in addition to the particle size, influencing the particle behavior and affecting our health. The surface area, chemical and biological composition, aspect ratio, and the charge are all factors characteristic of particles. OoC microfluidic chips are very useful for the pollutant toxicity measurements on various body tissues. A better understanding of pollutants will help to trace these to the potential sources. The data from the on-the-ground and satellite monitoring can be integrated into models, helping to predict and prevent pollution exposure.

Energy storage systems will play a key role for individual users in the future smart grid. They serve two purposes: (i) handling the intermittent nature of renewable energy resources for a more reliable and efficient system, and (ii) preventing the impact of blackouts on users and allowing for more independence from the grid, while saving money through load-shifting. In this paper we investigate the latter scenario by looking at a neighbourhood of 25 households whose demand is satisfied by one utility company. Assuming the users possess lithium-ion batteries, we answer the question of how each household can make the best use of their individual storage system given a real-time pricing policy. To this end, each user is modelled as a player of a non-cooperative scheduling game. The novelty of the game lies in the advanced battery model, which incorporates charging and discharging characteristics of lithium-ion batteries. The action set for each player comprises day-ahead schedules of their respective battery usage. We analyse different user behavior and are able to obtain a realistic and applicable understanding of the potential of these systems. As a result, we show the correlation between the efficiency of the battery and the outcome of the game.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

Assisted reproductive technology has been developed significantly throughout the past few years, particularly diagnosing and treating male infertility. Many studies have been performed showing that Intracytoplasmic Sperm Injection (ICSI) is a successful method to attain clinical pregnancy and live birth through impaired spermatozoa characteristics or low sperm count, such as severe oligospermia. Severe oligospermia indicates low sperm count, which in some cases leads to azoospermia. Severe oligospermia can be caused by several factors such as genetics or medication. In search of efficient treatment for couples with Severe oligospermia, numerous retrospective and prospective researches have reported high pregnancy and live birth rates through testicular sperm for men with severe oligospermia and cryptozoospermia with or without high sperm DNA damage. The research showed that the use of testicular sperm in combination with ICSI yielded a high pregnancy rate and live births over another source of sperm, such as ejaculated sperms. Moreover, the use of ICSI in severe oligospermia has shown successful fertilization and pregnancy.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

Recent developments in optical biosensors based on integrated photonic devices are reviewed with a special emphasis on silicon-on-insulator ring resonator. The review is mainly devoted to the following aspects: (1) Principles of sensing mechanism, (2) sensor design, (3) biofunctionalization procedures for specific molecule detection and (4) measurement set-ups and advances in chip-integration. The inherent challenges of implementing photonics-based biosensors to meet specific requirements of applications in medicine, food analysis, and environmental monitoring are discussed.

Wind turbine plants are complex dynamic and uncertain processes driven by stochastic inputs and disturbances, as well as different loads represented by gyroscopic, centrifugal, and gravitational forces. Moreover, as their aerodynamic models are nonlinear, both modelling and control become challenging problems. On one hand, high-fidelity simulators should contain different parameters and variables in order to accurately describe the main dynamic system behaviour. Therefore, the development of modelling and control for wind turbine systems should consider these complexity aspects. On the other hand, these control solutions have to include the main wind turbine dynamic characteristics without becoming too complicated. The main point of this paper is thus to provide two practical examples of development of robust control strategies when applied to a simulated wind turbine plant. Experiments with the wind turbine simulator and the Monte–Carlo tools represent the instruments for assessing the robustness and reliability aspects of the developed control methodologies when the model-reality mismatch and measurement errors are also considered. Advantages and drawbacks of these regulation methods are also highlighted with respect to different control strategies via proper performance metrics.

Various type of soils have been identified based on their electrical and magnetic properties, especially with regards to peat soils. Peat soils are commonly considered as partly decomposed vegetation. In this study, electrical and magnetic properties have been used in K-means clustering to identify layers of peat soils. K-means clustering is a partitioning method that treats observations in the data. Data cores were obtained at every centimeter and examined for their electrical conductivity (σ) and magnetic susceptibility (χ_m) properties. A 291 cm core was obtained at Tegal Arum Village in South Kalimantan, Indonesia. The K-means clustering results indicate two different layers at 148 cm, and this is supported by loss on ignition (LOI) measurements. In the first layers, a 87.65% LOI was found associated with peat soils (above 248 cm). Whereas, in the second layers, there was a 26.11% LOI associated with mineral soils (below 248 cm). The results of this study using K-means clustering can be used to delineate soil layers.

In this work is represented conceptual model of robot-manipulator for capture and holding no-cooperation client spacecraft, which has Payload Adapter interface PAS 1666 S, PAS 1194 C, PAS 1666 MVS, PAS 1184 VS, when there are dynamic errors of linear and angular position of client spacecraft in the interval +/-5 deg. per minute and +/-0.1 meters per minute respectively.

Microfluidic lab-on-chip devices are widely being developed for chemical and biological studies. One of the most commonly used types of these chips is perfusion microwells for culturing multicellular spheroids. The main challenge in such systems is the formation of substantial necrotic and hypoxic zones within the cultured spheroids. Herein, we propose a novel acoustofluidic integrated platform to tackle this bottleneck problem. We show that such an approach enhances cell viability and shrinks necrotic and hypoxic zones in these spheroid-on-a-chip platforms without the need to increase the flow rate, leading to a significant reduction in costly reagents' consumption. Proof-of-concept, designing procedures, and finite element numerical simulation are discussed in details. Also, the effects of acoustic and hydrodynamic parameters on the cultured cells are investigated. The results show that by increasing acoustic boundary displacement amplitude (d0), the spheroid’s proliferating zone enlarges greatly. Moreover, it is shown that by implementing d0=0.5 nm, the required flow rate to maintain the necrotic zone below 13% will be decreased 12 times compared to non-acoustic chips.

This study examined the effects of incorporating 8 weeks of biweekly upper limb loaded plyometric training (elastic band) into the in-season regimen of handball players. Trial participants were assigned between control (n = 15, age: 18.1±0.5 years, body mass: 73.7±13.9 kg) and experimental (n = 14, age: 17.7±0.3 years, body mass: 76.8±10.7 kg) groups. Measures obtained pre- and post- included a cycle ergometer force-velocity test, ball throwing velocity in three types throw, 1-RM bench press and pull-over, and anthropometric estimates of upper limb muscle volumes. Gains in the experimental group relative to controls included absolute muscle power (W) (Δ23.3%; t-test p<0.01; d=0.083), relative muscle power (W.kg-1) (Δ22.3%; t-test p<0.01; d=0.091), and all 3 types of ball throw (Δ18.6%, t-test p<0.01, d=0.097 on jumping shot; Δ18.6%, t-test p<0.01; d=0.101 on 3-step running throw; and Δ19.1%, t-test p<0.01, d=0.072 on standing throw). Furthermore, a significant improvement by time interactions was observed in both groups on 1-RM bench press and pull-over performance. However, upper limb muscle volumes remained unchanged in both groups. We conclude that adding biweekly elastic band plyometric training to standard training improves measures important to game performance. Accordingly, such exercises can usefully be adopted as a part of handball training.

In this paper a full state feedback control of a double inverted pendulum on a cart (DIPC) are designed and compared. Modeling is based on Euler-Lagrange equations derived by specifying a Lagrangian, difference between kinetic and potential energy of the DIPC system. A full state feedback control with H infinity and H 2 is addressed. Two approaches are tested: open loop impulse response and a double inverted pendulum on a cart with full state feedback H infinity and H 2 controllers. Simulations reveal superior performance of the double inverted pendulum on a cart with full state feedback H infinity controller.

Three-dimensional (3D) cell culture systems can be regarded as suitable platforms to bridge the huge gap between animal studies and two-dimensional (2D) monolayer cell culture to study chronic diseases such as cancer. In particular, the preclinical platforms for multicellular spheroid formation and culture can be regarded as ideal in vitro tumor models. The complex tumor microenvironment such as hypoxic region and necrotic core can be recapitulated in 3D spheroid configuration. Cells aggregated in spheroid structures can better illustrate the performance of anti-cancer drugs as well. Various methods have been proposed so far to create such 3D spheroid aggregations. Both conventional techniques and microfluidic methods can be used for generation of multicellular spheroids. In this review paper, we first discuss various spheroid formation phases. Then, the conventional spheroid formation techniques such as bioreactor flasks, liquid overlay and hanging droplet technique are explained. Next, a particular topic of the hydrogel in spheroid formation and culture is explored. This topic has received less attention in the literature. Hydrogels entail some advantages to the spheroid formation and culture such as size uniformity, the formation of porous spheroids or hetero-spheroids as well as chemosensitivity and invasion assays and protecting from shear stress. Finally, microfluidic methods for spheroid formation and culture are briefly reviewed.

The use of naturally available materials not conforming to traditional specifications or standards, in the base and sub-base layers of road pavement structures, stabilised with New-age (Nano) Modified Emulsions (NME), have been tested, implemented and successfully verified through Accelerated Pavement Testing (APT) in South Africa. This was made possible through the development and use of a design procedure addressing fundamental principles and based on scientific concepts, which are universally applicable. The understanding of and incorporation of the chemical interaction between the mineralogy of the materials and a NME stabilising agent (compatibility between the chemistry of the reactive agents and material mineralogy) into the design approach is key to achieving the required engineering properties. Stabilised materials evaluation is done using tests indicative of the basic engineering properties (physics) of compressive strengths, tensile strengths and durability. This article describes the basic materials design approach developed to ensure that organofunctional nano-silane modified emulsions can successfully be used for pavement layer construction utilising naturally available materials, at a low risk. The enablement of the use of naturally available materials in all pavement layers can have a considerable impact on the unit cost and life-cycle costs of road transportation infrastructure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Power disaggregation aims at determining the appliance-by-appliance electricity consumption leveraging upon a single meter only, which measures the entire power demand. Data-driven procedures based on Factorial Hidden Markov Models have been proven remarkable results on energy disaggregation. Nevertheless, those procedures have various weaknesses: there is a scalability problem as the number of devices to observe raises and the algorithmic complexity of the inference step is severe. DNN architectures, such as Convolutional Neural Networks, have demonstrated to be a viable solution to deal with FHMMs shortcomings. Nonetheless, there are two significant limitations: a complicated and time-consuming training system based on back-propagation has to be employed to estimates the neural architecture parameters, and large amounts of training data covering as many operation conditions as possible need to be collected to attain top performances. In this work, we aim to overcome those limitations by leveraging upon the unique and useful characteristics of the extreme learning machine technique, which is based on a collection of randomly chosen hidden units and analytically defined output weights. Experiment evaluation has been conducted using the UK-DALE corpus. We find that the suggested approach achieves similar performances to recently proposed ANN-based methods and outperforms FHMMs. Besides, our solution generalises well to unseen houses.

Access and Benefit Sharing (ABS) is a framework which refers to a relatively recent type of legal requirements for access to and/or use of “genetic resources”. They are based on diverse national and regional laws and regulations, which mostly result from the implementation of the United Nations’ Convention on Biological Diversity (CBD) and its supplementary agreement, the Nagoya Protocol. Their ambition is to achieve fair and equitable sharing of benefits arising out of the use of genetic resources as an incentive to conserve and sustainably use them. This paper describes the experiences, practical constraints and complexities encountered by users of genetic resources when dealing with ABS legislation, with a focus on users from the private sector. We provide insights on how ABS laws have fundamentally changed the way of working with genetic resources in the hope that it inspires re-thinking of the ABS framework, to better support the overall objectives of the CBD.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

Regarding the high efficiency of metaheuristic techniques in energy performance analysis, this paper scrutinizes and compares five novel optimizers, namely biogeography-based optimization (BBO), invasive weed optimization (IWO), social spider algorithm (SOSA), shuffled frog leaping algorithm (SFLA), and harmony search algorithm (HSA) for the early prediction of cooling load in residential buildings. The algorithms are coupled with a multi-layer perceptron (MLP) to adjust the neural parameters that connect the CL with the influential factors. The complexity of the models is optimized by means of a trial-and-error effort, and it was shown that the BBO and IWO need more crowded spaces for fulfilling the optimization. The results revealed that the internal parameters (i.e., biases and weights) suggested by the BBO generate the most reliable MLP for both analyzing and generalizing the CL pattern (with nearly 93 and 92% correlations, respectively). Followed by this, the IWO emerged as the second powerful optimizer with mean absolute errors of 1.8632 and 1.9110 in the training and testing phases. Therefore, the BBO-MLP and IWO-MLP can be reliably used for accurate analysis of the CL in future projects.

The aim of this study is to introduce a novel method which can separate sand or gravel dominated bed load transport in rivers with mixed-size bed material. In engineering practice, the Shields-Parker diagram could be used for such purposes, however, the method has certain applicability limits, due to the fact that it is based on uniform bed material and provides information rather on river-scale, instead of reach or local scale. When dealing with large rivers with complex hydrodynamics and morphodynamics the bed load transport modes can also indicate strong variation even locally, which requires a more suitable approach to estimate the locally unique behavior of the sediment transport. Here, we suggest that the decision criteria utilizes the shear Reynolds number (Re*). The method was verified against field and laboratory measurement data, both performed at non-uniform bed material compositions. The comparative assessment of the results show that the shear Reynolds number based method operates more reliably than the Shields-Parker diagram and it is expected to predict the sand or gravel transport domination with a < 5% uncertainty. The introduced results can greatly contribute to the improvement of numerical sediment transport modeling as well as to the field implementation of bed load transport measurements.

Aneuploidy should compromise cellular proliferation but paradoxically favours tumour progression and poor prognosis. Here, we consider this paradox in terms of our most recent observations of chemo/radio-resistant cells undergoing reversible polyploidy. The latter perform segregation of two parental groups of end-to-end linked dyads by pseudo-mitosis creating tetraploid cells through a dysfunctional spindle. This is followed by autokaryogamy and homologous pairing preceding a bi-looped endo-prophase. The associated RAD51 and DMC1/γ-H2AX double-strand break repair foci are tandemly situated on the AURKB/REC8/kinetochore doublets along replicated chromosome loops, indicative of recombination events. MOS-associated REC8-positive peri-nucleolar centromere cluster organises a monopolar spindle. The process is completed by reduction divisions (bi-polar or with radial cytotomy including pedogamic exchanges) and release of secondary cells and/or formation of an embryoid. Together this process preserves genomic integrity and chromosome pairing, while tolerating aneuploidy by by-passing the mitotic spindle and meiotic SC checkpoints. Concurrently, it reduces the chromosome number and facilitates recombination that decreases the mutation load of aneuploidy and lethality in the chemo-resistant tumour cells. This cancer life-cycle has parallels both within the cycling polyploidy of the asexual life cycles of ancient unicellular protists and cleavage embryos of early multicellulars, supporting the atavistic theory of cancer.

The popular motor drive systems with a single two-level voltage source inverter (VSI) have one main problem that is the occurrence of the common-mode voltage (CMV), which is an effect of the electromagnetic interference, shaft voltage, bearing currents, leakage current. These cause the high stress, increasung temperature and early mechanical failure in machine. To overcome this problem, the technology of the dual two-level VSI fed open-end three-phase ac loads is now available to eliminate the CMV at the ac/induction motor load with the 120-degree modulation technique for controlling each inverter. In this paper, the discontinuous space vector modulation (DSVM) schemes are proposed and applied for the dual two-level VSI fed open-end load. It is based on the 120-degree modulation technique by using only 12 active voltage vectors and the 10 zero voltage vectors from the total 64 voltage vectors along with the different five-segment swicthing sequence designs with centralizing pulse width modulation technqiue in order to not only cancel the CMV in the ac load, but also reduce the switching number/switching loss of the conversion system. Among the various DSVM schemes, their performances are compared in this paper, such as the number of the switching, the step and peak value of the CMV in each inverter, and the quality of the output waveform, etc. The details of the verfication and comparison are carried out by simulation using Matlab/Simulink software.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

Hepatitis-C is one of the most common viral diseases caused by hepatitis C virus (HCV). It is responsible for millions of deaths each year in the developing world. The common dissemination paths of HCV include the use of contaminated water and transfusion of infected blood. Control of this virus has become a challenge for scientists and health professionals due to its versatility and adaptability in different host environments. Along with other problems, lack of efficient diagnosis, quantification and genotyping of viral strains are the major hindrances in a management of this notorious epidemic. The knowledge of HCV genotype and an amount of virus in patient’s blood are pre-requisites to determine the duration and method of treatment. In this review, we discuss the implications of HCV molecular diagnostic methods and their clinical applications. We conclude that while, several commercial and home-brewed methods are available for this purpose, and there is a visible vacuum for cost effective, robust, sensitive assays that can detect multiple viral genotypes in a single reaction. We are of the view that the level of sensitivity offered by Reverse Transcriptase-Polymerase Chain Reaction (RT-PCR) technique is unequivocal as compared to other techniques. Therefore, researchers may explore further possibilities using this technique in the management of HCV.

Reinforced concrete (RC) columns are often placed under confinement to increase their strength and ductility. Carbon fiber reinforced polymer (CFRP) materials have recently been recognized as favorable confinement systems. At present, a number of national standards and codes dedicated to the design of concrete components strengthened with CFRP in general and CFRP confinement in particular are available. These sets of rules provide design equations for confined reinforced concrete columns with circular and rectangular cross sections. Most of the standards and codes exhibit significant differences, including the used predictive models limitations, observed effects, and covered loading conditions. In this paper, five international standards and design guidelines are introduced and discussed. The purpose is to present a constructive and critical assessment of the state-of-the-art design methodologies available for CFRP confined RC columns and to discuss effects not previously considered properly. Therefore, some recent research efforts and findings from the Leipzig University of Applied Sciences are also introduced. The obtained data is used for a comparative study of the guideline predictive equations. Furthermore, it is shown that some new findings concerning the rupture strength and the maximum strength plus accompanying axial strain of a CFRP confined column are suitable to improve the current guidelines.

Background: The reference test for SARS-CoV-2 detection is the reverse transcriptase real time PCR (real time RT-PCR). However, evidences reported that real time RT-PCR has a lower sensitivity compared with the droplet digital PCR (ddPCR) leading to possible false negative in low viral load cases. Methods: We used ddPCR for viral genes N1 and N2 on 20 negative (no detection) samples from symptomatic hospitalized COVID-patients presenting fluctuating real time RT-PCR results and 10 suspected samples (Ct value>35) from asymptomatic not hospitalized subjects. Results: ddPCR performed on RNA revealed 65% of positivity for at least one viral target in the hospitalized patients group of samples (35% for N1 and N2, 10% only for N1 and 20% only for N2) and 50% in the suspected cases (30% for N1 and N2, while 20% only for N2). On hospitalized patients’ samples, we applied also a direct ddPCR approach on the swab material, achieving an overall positivity of 83%. Conclusion: ddPCR, in particular the direct quantitation on swabs, shows a sensitivity advantage for the SARS-CoV-2 identification and may be useful to reduce the false negative diagnosis, especially for low viral load suspected samples.

Non-intrusive load monitoring (NILM) is a core technology for demand response (DR) and energy conservation services. Traditional NILM methods are rarely combined with practical applications, and most studies aim to decompose the whole loads in a household, which leads to low identification accuracy. In this paper, an NILM approach based on multi-feature integrated classification (MFIC) is explored, which combines some non-electrical features such as ON/OFF duration, usage frequency of appliances, and usage period to improve load differentiability. The implementation of MFIC algorithm is consistent with traditional event-based method. The uniqueness of our algorithm is that it designs an event detector based on steady-state segmentation and a linear discriminant classifier group based on multi-feature global similarity. Simulation results using an open-access dataset demonstrate the effectiveness and high accuracy of MFIC algorithm, with the state-of-the-art NILM methods as benchmarks.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

In the paper, an improved smart meter data-based three-stage algorithm to calculate the power/energy losses in the three-phase networks with the voltage level below 0.4 kV (low voltage - LV) is presented. In the first stage, a loading function of input data was built having as main feature the working at the same time with files from the database of smart metering system (SMS) containing the hourly electricity records, and files including the characteristic load profiles established by the Distribution Network Operator (DNO) for the consumers with standard energy meters depending the following factors: consumption class, day and season. In the second stage, a function which is based on the work with the structure vectors was implemented to identify easy the configuration of analysed networks. In the third stage, an improved version of forward/backward sweep-based algorithm was proposed to calculate fast the power/energy losses to three-phase LV distribution networks in balanced and unbalanced regime. A real LV rural distribution network from a pilot zone belonging to a Distribution Network Operator (DNO) from Romania was used to confirm the accuracy of the proposed approach. The comparison with the results obtained using the DigSilent PowerFactory Simulation Package certified the performance of the algorithm, the mean absolute percentage error (MAPE) being 0.94%.

As described in previous work, the use of synthetic chemical ingredients in modern cosmetics is postulated to be a cause of damage to the skin microbiome. The discovery that biodiversity on the human skin is currently the only reliable indicator of skin health, meant that for the first time, a mechanism to test for healthy skin was possible. Using this mechanism and in collaboration with The Medical University of Graz, who carried out the independent study, this work aimed to help answer whether modern day synthetic cosmetics are a main cause of long term damage to the skin microbiome. Thirty-two human participants tested three different face washes for their effect on the skin’s microbial diversity, along with skin pH, moisture and TEWL (trans-epidermal water loss), washing twice a day for four weeks. The upper volar forearm of the volunteers was swabbed at the beginning, two weeks in and end (four weeks). 16S rRNA sequencing was used. One leading ‘natural’ brand full of synthetic ingredients, a leading synthetic brand and a 100% natural face wash were used. Results give the first indications of a link between synthetic ingredients in a cosmetics product, and its effect on skin microbiome biodiversity. It paves the way for future studies on the topic with a larger sample group, longer test period and standardised methodology to create a universal standard for testing the health of skin using benchmark diversity values. This can be used in the future to test the effectiveness of cosmetics or ingredients on skin health, leading to the banning of products proven to harm the skin’s natural environment.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

We introduce a new class of Vertex Operator Algebras Y+ and their duals, which generalize the standard W-algebras WN of type sl(N). These algebras can be defined in terms of junctions of boundary conditions and interfaces in the GL-twisted N = 4 Super Yang Mills gauge theory. The aim of these technical calculations is to find the relation of these ortho-symplectic Y-algebras to truncations of even W\infinity.

Concrete is a very common construction material. As time prevails, cracks often appear in structures that pose a threat to strength and durability, which ultimately affect the structural integrity of concrete. Extensive work has been carried out in past on utilization of Carbon Fiber Reinforced Polymer (CFRP) as a repair material. But, this research particularly focuses on: multiple fiber layers i.e. single and double, traditional concrete mix ratio with locally available materials and varying flexural reinforcement. Furthermore, this work presents an experimental analysis to strengthen the Reinforced Concrete (RC) beams using SikaWrap- 230 C as a CFRP wrap, and Sikadur-330 as a bonding material. The comparison between single and double layers of CFRP is of major interest in this research. Six reinforced concrete beams were repaired with CFRP and tested under three-point bending test. For these specimens, load deflection behavior along with crack propagation and failure of beams were studied. Experimental results show that beams repaired using CFRP wrapping achieved higher flexural capacity and ductility as compared with reference beam. Moreover, results reveal that introduction of second layer of fiber caused around 4-5.2% increment in flexural strength and resulted in higher ductility of RCC beam.

Ever since pharmacy has become a profession, pharmacist's role has been continuously subjected to changes due to specific influences from historical, socio-economic, political, and scientific context. Nowadays the classic perception of pharmaceutical profession in Community Pharmacy is facing worldwide extinction due to many factors. Modern services, such as online, mail-order, and telephone-order pharmacies are increasingly gaining ground thanks to their ability to facilitate customer demand. However, at the same time, they are endangering “face-to-face” contact, affecting the building of customer loyalty based on direct “human” interaction, and consequently reducing pharmacists to mere commercial figures. Communication is in fact emphasized as the essential element to build a solid and appropriate interpersonal relationship with the client, to make the consultancy process effective, and to strengthen pharmacist's professionalism in community pharmacy. The aim of this work is to analyze pharmacist’s role in modern society by pinpointing the factors affecting pharmacy profession practice. Specific purpose will be improving both the academic training of future professionals and their capacity to approach public relations through a deepened study and practice of behavioral, communication, educational, and sociological methodologies and techniques that would allow the development of more effective communication skills useful for providing an efficient consultancy service.