To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

The behaviour of steel frame buildings under progressive collapse conditions depends on a combination of several parameters including the interplay between different collapse resistance mechanisms mobilized in different structural components. Previous studies have shown that the extent to which these mechanisms may contribute to progressive collapse resistance depends on the ability of the beam-column connections to undergo large inelastic deformations prior to reaching their deformation capacity limits. For this reason, and due to the important role of their flexural strength and tying capacity in the development of essential collapse resistance mechanisms, the response of beam-column connections is one of the most important features of progressive collapse performance. Based on the knowledge gained through previous studies on the mechanics of the problem, the role of the connections is critically reviewed by examining the results of several experimental studies conducted during the past decade. The factors that may adversely affect progressive collapse resistance – such as failure modes of certain connection types – are evaluated, and novel approaches of limiting these factors which are currently under development are reviewed. The assessment of these parameters leads to useful conclusions of practical significance, while highlighting the aspects of the problem that need further study and understanding.

Chromatographic separation is a critical technique in the manufacturing processes of both chemical products and biopharmaceuticals. Its principle relies on exploiting the differences in distribution between the stationary and mobile phases to achieve the separation of mixtures. The precision of substance concentration during separation directly impacts the quality and usability of the final product. Therefore, the development of an effective and precise separation control technique has long been a vital concern in the field of chromatographic separation control. Currently, the employment of Simulated Moving Bed (SMB) technology for chromatographic separation, which allows for continuous feed, has been recognized as a cutting-edge technique. SMB is a continuous process technology that enhances the efficiency of adsorbents within the bed. This sequential multi-column SMB technology not only increases production capacity but also reduces the consumption of solvents and water. It is acknowledged as one of the cleanest manufacturing technologies in the biopharmaceutical industry. However, multi-column SMB involves various variables such as flow rates in multiple sections and valve switching times, rendering its system control highly complex. Unlike traditional control objectives that aim to minimize control output errors, the control objective of SMB is to achieve a specific proportion of substance concentration. Consequently, designing and implementing traditional control theories for SMB is challenging, leading to SMB systems largely being controlled based on simple PLC controls. Moreover, these controls are often applicable only to single or a few-column SMB setups, limiting the effectiveness of high-capacity applications. To achieve effective control of SMB, this study employs an adjustable intelligent fuzzy controller with a structure like an approximate neural network (NN) for SMB control research. Simulation results demonstrate that the intelligent controller effectively achieves desirable control outcomes for the SMB system.

Stochastic modelling of geometrically imperfect steel frame structures requires inputs of statistical values of the imperfection parameters, in some cases also with suitably selected mutual correlations between these input parameters. The paper presents a verification study of two stochastic methods to directly model the initial global geometrical imperfections of the steel frame structures. The stochastic input values of geometrical imperfections are derived from the tolerance criteria of the corresponding European Standard. Two advanced stochastic methods have been developed, referred as #RSS (random story sway) and #RSP (random story position). These methods are verified using random sampling simulations. This study provides useful provisions for the advanced numerical analyses of multi-story steel frames of various geometries. The proposed methods are verified for equidistant story heights and for structures of up to 24 stories, hence might be used for the most types of the standard steel frame structures.

The small satellite market continues to grow year after year. A compound annual growth rate of 17% is estimated during the period between 2020 and 2025. Low-cost satellites can send a vast amount of images to be post-processed at the ground to improve the quality and extract detailed information. In this domain lies the resolution enhancement task, where a low-resolution image is converted to a higher resolution automatically. Deep learning approaches to Super-Resolution (SR) reached the state-of-the-art in multiple benchmarks; however, most of them were studied in a single-frame fashion. With satellite imagery, multi-frame images can be obtained at different conditions giving the possibility to add more information per image and improve the final analysis. In this context, we developed and applied to the PROBA-V dataset of multi-frame satellite images a model that recently topped the European Space Agency’s Multi-frame Super Resolution (MFSR) competition. The model is based on proven methods that worked on 2D images tweaked to work on 3D: the Wide Activation Super Resolution (WDSR) family. We show that with a simple 3D CNN residual architecture with WDSR blocks and a frame permutation technique as data augmentation better scores can be achieved than with more complex models. Moreover, the model requires few hardware resources, both for training and evaluation, so it can be applied directly from a personal laptop.

In research applications across several areas, noise removal is indispensable for accuracy of final results. Noise is caused due to physical principals, such as background electronic noise, quantum effect, and wave rebound effect to name a few. Noise removal can help improve results in medical, astronomy, defense, and numerous other fields. Addressing this limitation would result in potentially low cost, automatic, and reliable systems. In this paper, a generalized new approach i.e. Multi-Frame Noise Removal (MFNR) is proposed for noise removal. Given any type of data, the probability density function (PDF) of the noise can be determined. Herein, we extracted the noise PDF parameters using KDE (Kernel Density Estimation). Because the data is corrupted by “deterministic” noise, hence can be cleaned. This could be used as a general purpose noise removal tool. The data point with same position in multiple frames helps us determine the noise PDF characteristics and hence making it possible to remove noise. The conventional wisdom which states that noise removal and detail preservation are contrary to each other is not true for MFNR. Experimental results validate our proposed method which showed practically complete noise reduction based on number of frames used, as compared to existing benchmark methods.

Cerebrovascular and airway structures are tubular structures used for transporting blood and gases, respectively, providing essential support for the normal activities of the human body. Accurately segmenting these tubular structures is the basis of morphology research and patho-logical detection. Nevertheless, accurately segmenting these structures from images presents great challenges due to their complex morphological and topological characteristics. To address this challenge, this paper proposes a framework UARAI based on the U-Net multi-scale reverse at-tention network and sparse convolution network. The framework utilizes a multi-scale structure to effectively extract the global and deep detail features of vessels and airways. Further, it enhances the extraction ability of fine-edge features by a joint reverse attention module. In addition, the sparse convolution structure is introduced to improve the features' expression ability without increasing the model's complexity. Finally, the proposed training sample cropping strategy re-duces the influence of block boundaries on the accuracy of tubular structure segmentation. The experimental findings demonstrate that the UARAI-based metrics, namely Dice and IoU, achieve impressive scores of 90.31% and 82.33% for cerebrovascular segmentation and 93.34% and 87.51% for airway segmentation, respectively. Compared to commonly employed segmentation tech-niques, the proposed method exhibits remarkable accuracy and robustness in delineating tubular structures such as cerebrovascular and airway. These results hold significant promise in facilitating medical image analysis and clinical diagnosis, offering invaluable support to healthcare profes-sionals.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Salinity acts as a critical environmental filter on microbial communities in natural systems, negatively affecting microbial diversity. However, how salinity affects the community assembly remains unclear. This study used Wendeng multi-pond saltern as a model to evaluate the prokaryotic community composition and diversity and quantify the relative importance of ecological processes across salinity gradients. Results showed that low saline salterns (45-80 g/L) exhibited higher bacterial diversity than those in high saline salterns (175-265 g/L). The relative abundance of taxa assigned to Halanaerobiaceae, Haloferacaceae, Desulfohalobiaceae, Phormidiaceae, Rohodobacteraceae, and Nitrococcaceae was higher with increasing salinity. Salinity and pH were the primary environmental factors that directly or indirectly determined the composition and diversity of prokaryotic communities. Microbial co-occurrence network dynamics were more complex in the sediment than in water of salterns. An infer Community Assembly Mechanisms by Phylogenetic-bin-based null model analysis (iCAMP) showed that microbial community assembly in sediment and water differed. Our findings provide more information about microbial community structure and the importance of various ecological processes in controlling microbial community diversity and succession along salinity gradients in water and sediment environments.

Existing reinforced concrete buildings with seismically-deficient column details affect the overall behavior depending on the failure type of column. The purpose of this study is to develop and validate a machine learning-based prediction model for the column failure modes (shear, flexure-shear and flexure failure modes). For this purpose, artificial neural network (ANN), K-nearest neighbor (KNN), decision tree (DT), and random forest (RF) models were used considering previously-collected experimental data. Using four machine learning methodologies, we developed a classification learning model that can predict the column failure modes in terms of the input variables using concrete compressive strength, steel yield strength, axial load ratio, height-to-dept aspect ratio, longitudinal reinforcement ratio, and transverse reinforcement ratio. The performance of each machine learning model was compared and verified by calculating accuracy, precision, recall, F1-Score, and ROC. Based on the performance measurements of the classification model, the RF model represents the highest average value of the classification model performance measurements among the considered learning methods, and it can conservatively predict the shear failure mode. Thus, the RF model can rapidly predict the column failure modes with the simple column details. Additionally, it was demonstrated that the predicted failure modes from the selected model were exactly same as the failure mode determined from a code-defined equation (traditional method)

Food analysis demands fast methods for routine control and high throughput of samples. Chromatographic separation enables simultaneous determination of numerous compounds in complex matrices, several approaches increasing separation efficiency and speed of analysis were involved. In this work, modern types of column with monolithic rod or superficially porous particles were employed and compared for determination of eight synthetic food dyes, their chromatographic performance was evaluated. During method optimization, cyano stationary phase Chromolith Performance CN 100 × 4.6 mm and Ascentis Express ES-CN 100 × 4.6 mm, 5 µm were selected for the separation of polar colorants. The separation was performed by gradient elution of acetonitrile/methanol and 2% water solution of ammonium acetate at flow rate 2.0 ml min-1. Mobile phase composition and the gradients were optimized in order to enable efficient separation on both columns. The method using fused-core particle column provided higher separation efficiency, narrow peaks of analytes resulted in increased peak capacity and shortening of analysis time. After the validation, the method was applied for analysis of colored beers, soft drinks and candies.

In recent decades, porous scaffolds for bone tissue engineering (BTE) have gained significant attention. Considerable research efforts have been dedicated to investigating the impact of scaffold pore size on a diverse array of biological processes, including cell-scaffold interactions, substance transportation, and vascularization. However, the multi-scale hierarchical porosity, a key structural characteristic of natural bone, has rarely been replicated in BTE scaffolds due to the challenges of controlling the scaffold structure across multiple length scales. With the advancement of manufacturing technology, there has been increasing research on biomimetic multi-scale hierarchical materials, which are also gaining favor in the field of BTE. Therefore, there is an urgent need to review multi-scale hierarchical porous BTE scaffolds. This paper aims to review the role and fabrication methods of multi-scale porous BTE scaffolds at different length scales, the design and manufacturing of new BTE scaffolds for bone regeneration.

Tree condition, pruning and orchard management practices within intensive horticultural tree crop systems can be determined via measurements of tree structure. Multi-spectral imagery acquired from an unmanned aerial system (UAS) has been demonstrated as an accurate and efficient platform for measuring various tree structural attributes, but research in complex horticultural environments has been limited. This research established a methodology for accurately estimating tree crown height, extent, plant projective cover (PPC) and condition of avocado tree crops, from a UAS platform. Individual tree crowns were delineated using object-based image analysis. In comparison to field measured canopy heights, an image-derived canopy height model provided a coefficient of determination (R2) of 0.65 and relative root mean squared error of 6%. Tree crown length perpendicular to the hedgerow was accurately mapped. PPC was measured using spectral and textural image information and produced an R2 value of 0.62 against field data. A random forest classifier was applied to assign tree condition into four categories in accordance with industry standards, producing out-of-bag accuracies >96%. Our results demonstrate the potential of UAS-based mapping for the provision of information to support the horticulture industry and facilitate orchard-based assessment and management.

In this paper, the effect of multi-rotational speeds super-gravity field on the grain refinement and tensile properties of as-cast H13 steel were investigated systematically. The experimental results revealed that the as-cast grains of H13 steel can be significantly refined in multi-rotational speeds supergravity field. In conventional supergravity field, with the decrease of rotational radius, the secondary dendrite average spacing (SDAS) and the austenite grain average size (AGAS) increase, and the maximum values of SDAS and AGAS are 90 µm and 55 µm, respectively. while in multi-speeds supergravity fields, at the range of increasing rotational speeds, SDAS and AGAS decrease as the rotational radius decreases. In three-rotational speeds supergravity field, the maximum values of SDAS and AGAS are 80 µm and 50 µm. In five-rotational speeds supergravity field, the maximum values of SDAS and AGAS are reduced to 58 µm and 34 µm. Accordingly, both the tensile strength and the plasticity are enhanced with the increasing the number of rotational speeds in supergravity field, especially for the inner position of supergravity sample. The ultimate tensile strengths at outer, middle, and inner positions of H13 steel solidified in conventional supergravity field are 1445 MPa, 1378 MPa, and 1023 MPa, corresponding elongations of 2%, 1.5%, and 0.5%, while in the five-rotational speeds supergravity field, they are 1408 MPa, 1443 MPa, and 1453 MPa, corresponding elongations of 1.8%, 3.9%, and 2.2%. The mechanism for the grain refinement is that multi-speeds super-gravity can reduce the critical nucleation work of austenite, and the tangential force produced by changing the rotational speeds breaks dendrites at the solidification front, refining solidification structure.

Osteoporotic vertebral fracture is the most common fracture from osteoporosis, and are largely undiagnosed due to the mostly asymptomatic nature of the condition. It increases the risk of subsequent fractures and contributes to societal burden. Risk factors for osteoporotic fractures are found in the WHO fracture risk assessment model and used as a tool for monitoring bone health. Vertebral fractures are diagnosed from anteroposterior and lateral spine radiographs and are confirmed with an approximate loss of 20% vertebral height as compared to adjacent vertebrae. One of the most used grading for vertebral fractures is the SQ grading. Mild vertebral fractures could easily be misdiagnosed due to some peculiarities of the vertebral column. CT scan is useful for planning surgical intervention while an MRI scan can provide information about the recency of the fracture and rule out cancer-related fractures. Management depends on the severity of the fracture which could range from conservative management to surgical vertebral augmentation and decompression. Bisphosphonates are used to treat osteoporosis in acute and long-term management of fractures. Osteoimmunological therapies such as denosumab and romosozumab are new therapeutic interventions for osteoporosis while there are many other potential treatment options. Precision medicine provides an individualized treatment approach while regenerative medicine utilizes mesenchymal stem cells for fracture repair.

The BIOTON® biochar, produced by a wood biomass pyrolysis process, usually applied as a soil amendment, was investigated for a novel application, i.e. the adsorption of lead from contaminated solutions. The experimental activity firstly included the physical-chemical characterization of BIOTON®; SEM images were also obtained to highlight its internal structure. The adsorption process was investigated through batch and column experiments. Adsorption kinetics showed a very rapid achievement of the equilibrium conditions, i.e. at 2h and 4h for 50 mg/L and 100 mg/L initial Pb concentration, respectively. Complete removal also occurred within the same time. The Brunauer–Emmett–Teller model better fitted the equilibrium data for both Pb concentrations, whereas the kinetics were best represented by the pseudo second order model. The column tests showed that the addition of biochar as adsorbent media within the bed significantly extended the time of breakthrough and exhaustion, with respect to the column filled with soil only. The adsorption capacities of BIOTON® versus lead solutions was found to be comparable to that reported for commercial adsorbents. Therefore, BIOTON® can be considered a valid option, with the additional benefit to reduce the environmental impact since allows to recover a residue which alternately would need to be disposed of.

Hyperuricemia is mainly caused by the overproduction of uric acid (UA) catalyzed from xanthine by xanthine oxidase (XO) in abnormal purine metabolism in human body. There is an increasing demand for developing novel XO inhibitors of plant origins. The inhibition kinetics and type as well as actions of hesperetin against XO were investigated in vitro using multi-spectroscopic methods including UV-Vis absorption, Fourier transform infrared spectroscopy (FT-IR), fluorescence spectroscopy and molecular docking simulation. Results indicated that hesperetin reversibly inhibited XO in a competitive manner with an inhibition constant (Ki) value of (2.15 ± 0.05) × 10-6 mol/L. Hesperetin had a higher scavenging rate against O2- radical generated by the XO reaction system. The binding of hesperetin to the active site of XO altered the protein’s secondary structure as demonstrated by FT-IR and fluorescence spectra. Molecular docking study revealed that hesperetin had highly affinity to XO and the bonding of hesperetin to the molybdopterin (Mo-pt) active center inhibited not only substrate entry, but also prevented oxygen binding to flavin adenine dinucleotide (another active center in XO). Additionally, hydrophobic interactions and hydrogen bonds contributed to the stabilization of the hesperetin-XO complex. The results suggested that hesperetin be a promising natural XO inhibitor to alleviate hyperuricemia and gout.

Utilization of Bidirectional Reflectance Distribution Function (BRDF) model parameters obtained from the multi-angular remote sensing is one of the approaches for the retrieval of vegetation structural information. In this research, the potential of multi-angular vegetation indices, formulated by the combination of multi-spectral reflectance from different view angles, for the retrieval of forest above ground biomass was assessed. This research was implemented in the New England region with the availability of a high quality forest inventory database. The multi-angular vegetation indices were generated by the simulation of the Moderate Resolution Imaging Spectroradiometer (MODIS) BRDF/Albedo Model Parameters Product (MCD43A1 Version 6) based BRDF parameters. The effects of seasonal (spring, summer, autumn, and winter) composites of the multi-angular vegetation indices on above ground biomass, angular relationship of the spectral reflectance with above ground biomass, and the interrelationships between the multi-angular vegetation indices were analyzed. Among the existing multi-angular vegetation indices, only the Nadir BRDF-adjusted NDVI ( and Hot-spot incorporated NDVI ( showed significant relationship (more than 50%) with the above ground biomass. This research proposed two more sensitive vegetation structural indices, Fore-scattering Back-scattering NDVI and Vegetation Structure Index (VSI). The Fore-scattering Back-scattering NDVI showed higher sensitivity (R² = 0.62, RMSE = 52.46) towards the above ground biomass than existing multi-angular vegetation indices. Furthermore, the VSI performed in the most efficient way explaining 64% variation of the above ground biomass, suggesting that the right choice of the spectral channel and observation geometry should be considered for improving the estimates of the above ground biomass. In addition, the right choice of seasonal data (summer) was found to be important for estimating the forest biomass while other seasonal data were either insensitive or pointless. The promising results shown by the VSI suggest that it could be an appropriate candidate for monitoring vegetation structure from the multi-angular satellite remote sensing.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

The construction of reinforced concrete (RC) structures inevitably consumes an excessive number of rebars, leading to significant cutting waste and carbon emissions. Extensive research has been conducted to minimize this issue and its consequences; however, these methods consistently consume a substantial number of rebars. This includes a previous study that utilizes the lap splice position optimization and special-length rebar concept without considering the lapping zone regulation. Moreover, conventional lap splices pose inherent drawbacks that could jeopardize the structural integrity of RC members. In contrast, mechanical couplers eliminate the need for rebar lapping, effectively reducing rebar consumption. This research aims to evaluate the impact of an integrated mechanical coupler and special-length-priority minimization algorithm on the reduction in rebar consumption and cutting waste in RC columns, achieving near-zero cutting waste. To validate the effectiveness of the proposed algorithm, it was applied to the column rebars of an RC building. The results revealed a significant reduction in ordered rebar consumption by 18.25%, accompanied by substantial reductions in cutting waste (8.93%), carbon emissions (12.99%), and total costs (10.81%) compared with a previous study. The outcomes provide the industry with insights into further reducing rebar consumption and its related consequences. Applying the proposed algorithm to various construction projects will further amplify the corresponding benefits.

The dorsal column nuclei complex (DCN-complex) includes the dorsal column nuclei (DCN, referring to the gracile and cuneate nuclei collectively), external cuneate, X, and Z nuclei, and the median accessory nucleus. The DCN are organised by both somatotopy and modality, and have a diverse range of afferent inputs and projection targets. The functional organisation and connectivity of the DCN implicate them in a variety of sensorimotor functions, beyond their commonly accepted role in processing and transmitting somatosensory information to the thalamus, yet this is largely underappreciated in the literature. To consolidate insights into their sensorimotor functions, this review examines the morphology, organisation, and connectivity of the DCN and their associated nuclei. First, we briefly discuss the receptors, afferent fibres, and pathways involved in conveying tactile and proprioceptive information to the DCN. Next, we review the modality and somatotopic arrangements of the remaining constituents of the DCN-complex. Finally, we examine and discuss the functional implications of the myriad of DCN-complex projection targets throughout the diencephalon, midbrain, and hindbrain, in addition to their modulatory inputs from the cortex. The organisation and connectivity of the DCN-complex suggest that these nuclei should be considered a complex integration and distribution hub for sensorimotor information.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

Free-Living Amoebae (FLA) are widely distributed protozoa in both nature and artificial environments such as drinking water. Besides the ability of all FLA to transport various pathogenic microorganisms, certain species, Acanthamoeba spp. or Balamuthia mandrillaris, have intrinsic pathogenic abilities and cause severe cerebral infections. Previous work has shown an enrichment of FLA cysts in biofilm developed in upper levels of Drinking Water Storage Towers (DWST), suggesting that differences in densities of FLA cysts may play a role in their unequal distribution in the water column. To evaluate this hypothesis, a model of a water column was created for this study and used to analyze the vertical distribution of cysts of the FLA Acanthamoeba castellanii, Vermamoeba vermiformis and Balamuthia mandrillaris from 0 to 23 weeks. Interestingly, our data showed that the cysts of both A. castellanii and V. vermiformis were enriched in upper water levels during their aging. However, B. mandrillaris cysts were equally distributed in the water column during the entire study. These results showed that, besides the role of the water level variation in the DWST, some FLA cysts can become less dense during their aging, which contributes to their enrichment in upper water, and thus biofilm levels.

The use of friction-based Beam-to-Column Connections (BCC)s for earthquake-resistant Moment Resistant Frames (MRFs), aiming at eliminating damage to beam end sections due to the development of plastic hinges, has taken hold since the early eighties. Different technical solutions were proposed for steel structures, some were also designed for timber structures, while few more recent studies concern friction joints employed in reinforced concrete structures. Research aimed at characterizing the behavior of joints has focused on the evaluation of the tribological properties of the friction materials, coefficient of friction, shape and stability of the hysteresis cycles, influence of the temperature, speed of load application, effects of the application method, stability of preload, the influence of seismic excitation characteristics on the structural response, statistical characterization of amplitude and frequency of the slip excursion during seismic excitation. Studies aimed at identifying the design parameters capable of optimizing performance have focused attention mainly on the slip threshold, device stiffness, and deformation capacity. This review compiles the main and most recent solutions developed for MRFs. Furthermore, the pros and cons for each solution are highlighted, focusing on the dissipative capacity, shape and stability of hysteresis loops. In addition, the common issues affecting all friction connections, namely characteristics of friction shims and the role of bolt preload, are discussed. Based on the above considerations, a guideline can be outlined, which can help to choose the appropriate solutions for beam-to-column connections for MRFs.

Identifying skeletal remains has been and will remain a challenge for forensic doctors and forensic anthropologists, especially in disasters with multiple victims or skeletal remains in an advanced stage of decomposition. This study proposes a machine learning method to determine gender starting from morphometric analysis of L1-L5 lumbar vertebrae in a modern Romanian population. The purpose of the present study was to observe whether by using the ML method there is a good predictability of gender in forensic identification based on parameters obtained from the metric analysis of the lumbar spine specific to the Romanian population. This paper offers two models of ML, RF and XGB, each with its own characteristics, and presenting different performance, random forest having the best. For both, we used two metrics (accuracy and roc_auc), the latter being the most used to highlight model performance. The L1-L5 lumbar vertebrae exhibit sexual dimorphism and can be used in gender estimation. Machine learning is more accurate in determining gender than discriminatory function analysis.

The objective of this paper is to estimate the trend of Total Ozone Column (TOC) over Togo. Multi Sensor Reanalysis-2 (MSR-2) TOC over the entire territory of Togo were used. Multiple Linear Regression (MLR) method has been applied to retrieve the interannual contributions of different forcings and the long term variability. It was found that the Annual Oscillation (AnO), the Quasi Biennial Oscillation at 30 mb (QBO30), the Solar Flux (SF), and the El Niño–Southern Oscillation (ENSO) have statistically significant influence on the interannual variability of the TOC. The strongest contribution (22 ± 1.4 DU) is allocated to the AnO while the weakest (< 1 DU) is attributed to the Semi-Annual Oscillations (SAnO). Before the peak year of Equivalent Effective Stratospheric Chlorine (EESC) in tropics in 1997 the trend is negative (- 0.3% ± 0.9% per decade) and is not statistically significant. After the peak year, a statistically significant positive trend is observed. The trend of TOC is 0.6% ± 0.2% per decade. The monthly TOC trend over Togo is positive and statistically significant during the rainy season (particularly during the monsoon period) except in April, unlike during the harmatan period (DJF) where the trend is not significant.

In the present study, Electrocoagulated Metal Hydroxide Sludge (EMHS) was analyzed as adsorbent material to remove both fluoride ion (F-) and arsenic V (As(V)) from aqueous effluents. This material was generated during an electrocoagulation process using Aluminum anode. It was characterized by using specific surface areas and the surface morphology was studied by scanning electron microscopy (SEM). Adsorbent fixed-beds are generally studied to remove different class of contaminants. EMHS was evaluated using a continuous flow rate column test with an experimental design. The effect of initial concentration of F- (2.5–10 mg L⁻¹) and the Empty Bed Contact Time (EBCT (0.4–0.8 min)) was studied following a central composite design methodology. The experimented parameters had a significant influence on saturation time, breakthrough volume, and breakthrough time. A response surface analysis was a tool for analyzing the adsorption study, showing interactions that are complicated to identify by others methods. The results, here reported, revealed that EMHS is an efficient and promising adsorbent material in order to remove F- and As(V) from water contaminated by these pollutants.

A problem with synthetic aperture radar (SAR) is that, due to the poor penetrating action of electromagnetic waves inside solid bodies, the capability to observe inside distributed targets is precluded. Under these conditions, imaging action is provided only on the surface of distributed targets. The present work describes an imaging method based on the analysis of micro-movements on the Khnum-Khufu Pyramid, which are usually generated by background seismic waves. The results obtained prove to be very promising, as high-resolution full 3D tomographic imaging of the pyramid's interior and subsurface was achieved. Khnum-Khufu becomes transparent like a crystal when observed in the micro-movement domain. Based on this novelty, we have completely reconstructed internal objects, observing and measuring structures that have never been discovered before. The experimental results are estimated by processing series of SAR images from the second-generation Italian COSMO-SkyMed satellite system, demonstrating the effectiveness of the proposed method.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

In recent years, growing attention has been directed towards the potential of plant extracts as great therapeutic agents in controlling oxidative stress and inflammation. Gymnema inodorum (Lour.) Decne, an indigenous plant locally grown in Northern Thailand, is known for its anti-diabetic activity. This study aims to explore the antioxidant properties and phenolic profile of column chromatographic fractionated G. inodorum leaf extract. The ethanolic-reflux extracts of G. inodorum leaves were subjected to column chromatography for the isolation of bioactive molecules. Total phenolic and flavonoid content were assessed using Folin–Ciocalteu and aluminium chloride colorimetric methods, respectively. Total antioxidant activity was evaluated by employing different antioxidant assays, including 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulfonic)acid (ABTS) scavenging assay and ferric reducing antioxidant power (FRAP) assay. High-Performance Liquid Chromatography (HPLC) with a C18 column was employed to determine the level of gymnemic acid, while Liquid Chromatography Quadrupole Time-of-Flight/Mass Spectrometry (LC-QTOF/MS) was used to identify potential phenolic compounds. The three separated fractions indicating A, B, and C, exhibited remarkable antioxidant activity, with total phenolic content of 0.294 ± 0.056, 0.085 ± 0.039, and 0.227 ± 0.041 mg QE/mL, and total flavonoid content of 0.274 ± 0.050, 0.309 ± 0.110, and 0.384 ± 0.007 mg QE/mL, respectively. Fraction A exhibited the highest DPPH and ABTS scavenging activity, while fraction C demonstrated significantly higher ferric-reducing power. HPLC analysis revealed a highest concentration of gymnemic acid in fraction C (0.393 ± 0.003 mg/g) compared to fraction A (0.159 ± 0.003 mg/g) and fraction B (0.142 ± 0.000 mg/g). The LC-QTOF/MS phenolic screening showed seven potential phenolic compounds in fraction A, seven compounds in fraction B, and four compounds in Fraction C. A significant relationship is found between antioxidant potential and total phenolic content, suggesting that phenolic compounds are the major contributors to the antioxidant activity of G. inodorum.

The lordosis of the haemal part of the vertebral column is a frequent abnormality in reared fish. Haemal lordosis develops during the late larval and early juvenile period, mainly due to the high swimming activity of the fish in the rearing tanks. In the present study we examined whether haemal lordosis recovers during the growth of European sea bass. Furthermore, we aimed to develop simple morphometric indices (PrAn1 and PrAn2) that could link the severity of lordosis at the juvenile stage with fish morphological quality at harvesting. At 111 days post-hatching (dph, 53±4 mm standard length, SL), 600 seabass juveniles with lordotic (L, 200 fish) or normal (N, 400 fish) external morphology were selected and introduced in a common tank. At 150 dph (75±7 mm SL), 350 fish were randomly selected, pit-tagged and transferred in a sea cage for on-growing up to 502 dph (234±16 mm SL). The morphological examination of the fish at 150 and 502 dph revealed that the 60% (46 out of 77) of L juveniles turned into normal phenotype by the end of on-growing period. Interestingly, 56% of the fish with recovered external morphology (N-Rec) presented either a completely normal vertebral column (31%) or minor abnormalities of individual vertebrae (25%). Following the results of geometric morphometric analysis, the differences in the body shape between N-Rec and N fish were not significant (p&gt;0.05, canonical variate analysis). The examined morphometric indices were effective in discriminating the normal fish from the 58% (PrAn1) to 65% (PrAn2) of lordotic juveniles. Results are discussed with respect to the mechanism of lordosis recovery, as well as to their application for the quality control and cull out of the abnormal fish in the commercial hatcheries.

In our previous works we have proposed design equations that can predict with reasonable accuracy the transition point from homogeneous to heterogeneous regime as well as the gas holdup and the mean Sauter diameter at the homogeneous regime. The validity of the proposed correlations was checked with data obtained using different geometrical configurations and several Newtonian and non-Newtonian liquids as well as the addition of surfactants. However, in all the experiments the gas phase was atmospheric air. This work investigates the effect of gas phase properties by conducting experiments employing various gases (i.e., air, CO₂, He) that cover a wide range of physical property values. Experiments revealed that only the use of low-density gas (He) has a measurable effect on bubble column performance. More precisely, when the low-density gas (He) is employed, the transition point shifts to higher gas flow rates and the gas holdup decreases, a fact attributed to the lower momentum force exerted by the gas. In view of the new data, the proposed correlations have been slightly modified to include the effect of gas phase properties and it is found that they can predict the aforementioned quantities with an accuracy of ±15%. It has been also proved that CFD simulations are an accurate means for assessing the flow characteristics inside a bubble column.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

Although the statistical methods of downscaling climate data have progressed significantly, the development of high-resolution precipitation products continues to be a challenge. This is especially true when interest centres on downscaling value over several study sites. In this paper , we report a new downscaling method termed the multi-site Climate Generative Adversarial Network (MSCliGAN), which can simulate annual maximum precipitation to the regional scale during the 1950-2010 period in different cities in Canada by using different AOGCM's from the Coupled Model Inter-Comparison Project 6 (CMIP6) as input. Auxiliary information provided to the downscaling model included topography and land-cover. The downscaling framework uses a convolution encoder-decoder U-net network to create a generative network and a convolution encoder network to create a critic network. An adversarial training strategy is used to train the model. The critic/discriminator used Wasserstein distance as a loss measure and on the other hand the generator is optimized using a summation of content loss on Nash-Shutcliff Model Efficiency (NS), structural loss on structural similarity index (SSIM), and adversarial loss Wasserstein distance. Downscaling results show that downscaling AOGCMs by incorporating topography and land-use/land-cover can produce spatially coherent fields close to observation over multiple-sites. We believe the model has sufficient downscaling potential in data sparse regions where climate change information is often urgently needed.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

The current need to develop sustainable power sources has led to the development of ocean-based conversion systems. Wells turbine is a widely used converter in such systems which suffers from a lack of operational range and power production capacity under operational conditions. The profile named IFS which is concave in the post-mid-chord region, can produce significantly larger lift forces and show better separation behavior than the NACA profiles. In the present study, we tested this profile for the first time in a Wells turbine. The performance of six different blade designs with IFS and NACA profiles were evaluated and compared using a validated computational fluid dynamic model. Although the substitution of the NACA profile with the IFS profile in all cases increased the torque generated, the most efficient power generation and the largest efficient range were achieved in the design with varying thickness from the hub with a 0.15 thickness ratio reaching to the ratio of 0.2 at the tip. The operational span of this design with the IFS profile was 24.1% greater and the maximum torque generation was 71% higher than the case with the NACA profile. Therefore, the use of the IFS profile is suggested for further study and practical trials.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

Intelligent algorithms are recently used in the optimization process in chemical engineering and application of multiphase flows such as bubbling flow. This overview of modeling can be a great replacement with complex numerical methods or very time-consuming and disruptive measurement experimental process. In this study, we develop the adaptive network-based fuzzy inference system (ANFIS) method for mapping inputs and outputs together and understand the behavior of the fluid flow from other output parameters of the bubble column reactor. Neural cells can fully learn the process in their memory and after the training stage, the fuzzy structure predicts the multiphase flow data. Four inputs such as x coordinate, y coordinate, z coordinate, and air superficial velocity and one output such as pressure gradient are considered in the learning process of the ANFIS method. During the learning process, the different number of the membership function, type of membership functions and the number of inputs are examined to achieve the intelligent algorithm with high accuracy. The results show that as the number of inputs increases the accuracy of the ANFIS method rises up to almost for all cases, while the increment in the number of rules has a effect on the intelligence of artificial algorithm. This finding shows that the density of neural objects or higher input parameters enables the moded for better understanding. We also proposed a new evaluation of data in the bubble column reactor by mapping inputs and outputs and shuffle all parameters together to understand the behaviour of the multiphase flow as a function of either inputs or outputs. This new process of mapping inputs and outputs data provides a framework to fully understand the flow in the fluid domain in a short time of fuzzy structure calculation.

The water-rich liquid layer immobilized on the surface of the polar stationary phases is critical to the retention of polar compounds in hydrophilic interaction chromatography (HILIC). Although the presence of the adsorbed water layer has been investigated and confirmed by multiple techniques, there is a lack of quantitative measure that can be easily determined and linked to chromatographic parameters. This study proposes a simple measure termed volume ratio (the ratio of the adsorbed water layer volume and the mobile phase volume) that provides a relative, but quantitative information on the adsorbed water layer and may be linked to the phase ratio. The volume ratio can be easily determined using toluene elution volume. The volume ratio values are measured in 25 polar stationary phases in various mobile phase conditions. In addition to the acetonitrile content in the mobile phase, ammonium acetate concentration in the mobile phase and column temperature also have significant influences on the volume ratio and the adsorbed water layer.

In daily travel and activities, pathfinding is a significant process. They are often used in transportation routes calculation. They have now evolved to be able to solve most situations of the pathfinding and its related problems. This review describes previous and recent studies on the pathfinding algorithms. It reviews the development of pathfinding algorithms in a classification base on their usage. The aim is to summarize the application of the pathfinding algorithms for the readers interested in the subject that can be used as a supplement.

Multi-Faith Spaces (MFS) are a relatively recent invention that quickly gained in significance. On the one hand, they offer a convenient solution for satisfying needs of people with diverse beliefs in the institutional context of hospitals, schools, airports, etc. On the other hand, as Andrew Crompton pointed out, they are politically significant because the multi-faith paradigm “is replacing Christianity as the face of public religion in Europe” (2012, p. 493). Due to their ideological entanglement, MFS are often used as the means to promote either a more privatised version of religion, or a certain denominational preference. Two distinct designs are used to achieve these means: negative in the case of the former, and positive in the latter. Neither is without problems, and neither adequately fulfils its primary purpose of serving diverse groups of believers. Both, however, seem to follow the biases and main problems of secularism. In this paper, I analyse recent developments of MFS to detail their main problems and answer the question, whether the MFS, and the underlying Multi-Faith Paradigm, can be classified as a continuation of secularism.

Multi-channel and multi-parameter near-infrared spectrometers (NIRS) have gradually become a new research direction and hot spot due to their ability to provide real-time, continuous, comprehensive indicators of multiple parameters. However, multi-channel and multi-parameter detection may lead to crosstalk between signals. There is still a lack of benchmarks on the evaluation of reliability, sensitivity, stability and response consistency of the NIRS instrument. In this study, a set of test methods (the ink drop test, multi-channel crosstalk test and multi-parameter crosstalk test) for analysis crosstalk and verifying the reliability of NIRS were conducted to test experimental verification on a multi-channel (8-channel), multi-parameter (4-parameter) NIRS instrument independently developed by our team. Results show that these tests can be used to analyze the signal crosstalk and verify the reliability, sensitivity, stability and response consistency in the NIRS instrument. This study contributes to the establishment of benchmarks for the NIRS instrument crosstalk and reliability testing. These novel tests have the potential to become the benchmark for the NIRS instrument reliability testing.

Although there are several access control systems in the literature for flexible policy management in multi-authority and multi-domain environments, achieving interoperability &amp; scalability, without relying on strong trust assumptions, is still an open challenge. We present HMBAC, a distributed fine-grained access control model for shared and dynamic multi-authority and multi-domain environments, along with Janus, a practical system for HMBAC policy enforcement. The proposed HMBAC model supports: (a) dynamic trust management between different authorities; (b) flexible access control policy enforcement, defined at domain and cross-domain level; (c) a global source of truth for all entities, supported by an immutable, audit-friendly mechanism. Janus implements the HMBAC model and relies on the effective fusion of two core components. First, a Hierarchical Multi-Blockchain architecture that acts as a single access point that cannot be bypassed by users or authorities. Second, a Multi-Authority Attribute Based Encryption protocol that supports flexible shared multi-owner encryption, where attribute keys from different authorities are combined to decrypt data distributedly stored in different authorities. Our approach was implemented using Hyperledger Fabric as the underlying blockchain, with the system components placed in Kubernetes Docker container pods. We experimentally validated the effectiveness and efficiency of Janus, while fully reproducible artifacts of both our implementation and our measurements are provided.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

Breakthrough curves for the adsorption of H2S using a metal-oxides mixture were predicted using the Bohart-Adams model of fixed bed adsorption. This mixture (ZnMn2O4+ZnO+Mn2O3) came from the processing of an urban waste as spent alkaline batteries were. The H2S adsorption experiments were carried out in a fixed-bed column at 20º C, and under various experimental conditions: gas flow rate, inlet H2S concentration and adsorbent dosage. Curves predicted by the model matched well with experimental data, providing data for the possible scale-up of the system. At the various experimental variables, the efficiency of the column, were also provided in the work. This investigation demonstrated the usefulness of a waste material, like spent alkaline batteries, to provide an adsorbent material to mitigate the problem of the presence of this harmful gas.

The process of ultrasonic atomization involves a series of dynamic/topological deformations of free surface, though not always, of a bulk liquid (initially) below the air. This study focuses on such dynamic interfacial alterations realized by changing some acousto-related operating conditions, including ultrasound excitation frequency, acoustic strength or input power density, and the presence/absence of a “stabilizing” nozzle. High-speed, high-resolution imaging made it possible to qualitatively identify four representative transitions/demarcations: 1) the onset of a protrusion on otherwise flat free surface; 2) the appearance of undulation along the growing protuberance; 3) the triggering of emanating beads fountain out of this foundation-like region; and 4) the induction of droplets bursting and/or mist spreading. Quantitatively examined were the two-parameters specifications—on the degrees as well as induction—of the periodicity in the protrusion-surface and beads-fountain oscillations, detected over wider ranges of driving/excitation frequency (0.43–3.0 MHz) and input power density (0.5–10 W/cm2) applied to the ultrasound transducer of flat surface on which the nozzle was mounted or not. The resulting time sequence of images processed for the extended operating ranges, regarding the fountain structure pertaining in particular to recurring beads, confirms the wave-associated nature, i.e., their size “scalability” to the ultrasound wavelength, predictable from the traveling wave relationship. The thresholds in acoustic conditions for each of the four transition states of the fountain structure have been identified—notably, the onset of plausible “bifurcation” in the chain-beads diameter below a critical excitation frequency.

The current work addresses the control of two-input two-output (TITO) Wood and Berry model of a binary distillation column. The controller design problem is formulated in terms of multivariable H_∞ control synthesis. The controller structure takes the form of simplest static output feedback (SOF) control. The controller synthesis is performed using a hybrid approach of blending linear matrix inequalities (LMI) and genetic algorithm (GA). The performance of the static output feedback controller is compared with three other controllers designed for Wood and Berry model available in the literature. The first simulation study is performed for the case of tracking a unit step command in the presence of a step change in output disturbance. A second simulation study is performed for rejecting a change in sinusoidal output disturbance.

The paper proposes TOPSIS method for solving multi-objective multi-level programming problem (MO-MLPP) with fuzzy parameters via fuzzy goal programming (FGP). At first, - cut method is used to transform the fuzzily described MO-MLPP into deterministic MO-MLPP. Then, for specific , we construct the membership functions of distance functions from positive ideal solution (PIS) and negative ideal solution (NIS) of all level decision makers (DMs). Thereafter, FGP based multi-objective decision model is established for each level DM for obtaining individual optimal solution. A possible relaxation on decisions for all DMs is taken into account for satisfactory solution. Subsequently, two FGP models are developed and compromise optimal solutions are found by minimizing the sum of negative deviational variables. To recognize the better compromise optimal solution, the concept of distance functions is utilized. Finally, a novel algorithm for MO-MLPP involving fuzzy parameters is provided and an illustrative example is solved to verify the proposed procedure.

We develop an interactive likelihood (ILH) for sequential Monte-Carlo (SMC) methods for image-based multiple target tracking applications. The purpose of the ILH is to improve tracking accuracy by reducing the need for data association. In addition, we integrate a recently developed deep neural network for pedestrian detection along with the ILH with a multi-Bernoulli filter. We evaluate the performance of the multi-Bernoulli filter with the ILH and the pedestrian detector in a number of publicly available datasets (2003 PETS INMOVE, AFL, and TUD-Stadtmitte) using standard, well-known multi-target tracking metrics (OSPA and CLEAR MOT). In all datasets, the ILH term increases the tracking accuracy of the multi-Bernoulli filter.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) buildings and are often used for multistory housing. The evaluation of the peak deformation and hysteretic dissipated energy of such building structures is essential for the rational seismic design of RC buildings with SDCs. In a previous study, the authors proposed an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for high quality predictions. In this article, the V_ΔE1^*–D₁^*_max relationships of RC moment-resisting frames with and without SDCs are invested using a critical pseudo-double impulse (PDI) analysis based on a study by Takewaki and coauthors. The results show that the V_ΔE1^*–D₁^*_max relationship obtained from the critical PDI analysis agrees well with that calculated from the equations proposed in the previous study.

This paper presents the experimental and numerical study on a ductile beam-column connection between a composite reinforced concrete truss (CRCT) beam and Concrete Filled Tube (CFT) column subjected to bending and shear loads. Two experimental models with different beam-column joint testing schemes, extracted from the same prototype three-dimensional structure designed according to the rules of the capacity design provided by seismic code, were subjected to quasi-static cyclic tests by applying gravitational loads and the horizontal seismic force. The main objective of this paper is to verify the experimental ductile behavior of both specimens and to simulate the experimental global and local response by nonlinear static analysis considering different modelling approaches. The comparison between the experimental and numerical results highlights, for both models considered, the ductile and dissipative capacity of the connection system, designed following the criterion of the hierarchy of resistances proposed by the current Italian code. Different experimental setup showed similar results demonstrating the repeatability of the test and its reproducibility through the nonlinear numerical analysis.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

Satellite derived bathymetry methods over coastal areas were born to deliver basic and useful information like bathymetry. However, the process is not straightforward, the main limitation being the need of field data. The Self-calibrated Spectral Supervised Shallow-water Modeler (4SM) method was tested to obtain coastal bathymetry without the use of any field data. Using LANDSAT-8 multispectral images from 2013 to 2016, a bathymetric time series was produced. Groundtruthed depths and an alternative method, Stumpf’s Band Ratio Algorithm, were used to verify the results. Retrieved (4SM) vs groundtruthed depths scored an average r2 (0.90), and a low error (RMSE = 1.47 m). Also 4SM showed, over the whole time series, the same average accuracy of the control method (40%). Advantages, limitations and operability under complex atmosphere and water column conditions, and high and low-albedo bottom processing capabilities of 4SM are discussed. In conclusion, the findings suggest that 4SM is equally accurate as the commonly used Stumpf’s method, the only difference being the independence of 4SM to previous field data, and the potential to deliver bottom spectral characteristics for further modelling. 4SM represents a significative advance in coastal remote sensing potential to obtain bathymetry and optical properties of the marine bottom.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

One of the most important applications in the wireless sensor networks (WSN) is to classify mobile targets in the monitoring area. In this paper, a multi-DBN weighted voting classification algorithm is proposed on the basis of the Deep Belief Network (DBN) classifier and combined with the idea of voting method, which is implemented on the nodes of the WSN monitoring system by means of "upper training, lower transplantation" appraoch. The performance of the algorithm is verified by using real-world experimental data, and the results show that the proposed method has a higher accuracy in classifying the target signal features, achieving an average classification accuracy of 84.63% across four different types of moving targets. The experiment reveals that the multi-DBN weighted voting algorithm enhances the target classification accuracy by approximately 5% in comparison to the single DBN classifier, but the memory and computation time required for the algorithm to run are also increased at the same time. Compared to the FFNN classifier, which exhibited the highest classification accuracy among the four selected methods, the algorithm achieves an improvement of approximately 8.8% in classification accuracy. However, it incurs greater time overhead to run.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

Rapid assessment of maize yields in smallholder farming system is important to understand its spatial and temporal variability and for timely agronomic decision-support. Imageries acquired with unmanned air vehicles (UAV) offer opportunity to assess agronomic variables at field scale, however, it is not clear if this can be translated into reliable yield assessment on smallholder farms where field conditions, maize genotypes, and management practices vary within short distances. In this study, we assessed the predictability of maize grain yield using UAV-derived vegetation indices (VI), with(out) biophysical variables, in smallholder farms. High-resolution images were acquired with UAV-borne multispectral sensor at 4 and 8 weeks after sowing (WAS) on 31 farmers’ managed fields (FMFs) and 12 nearby Nutrient Omission Trials (NOT), all distributed across 5 locations within the core maize region of Nigeria. The NOTs included non-fertilized and fertilized plots (with and without micronutrients), sown with open-pollinated or hybrid maize genotypes. Acquired multispectral images were post-processed into several three (s) vegetation indices (VIs), normalized difference vegetation index (NDVI), normalized difference red-edge (NDRE), green-normalized difference vegetation index (GNDVI). Biophysical variables, plant height (Ht) and percent canopy cover (CC), were measured with the georeferenced plot locations recorded. In the NOTs, the nutrient status, not genotype, influenced the grain yield variability and outcome. The maximum grain yield observed in NOTs was 9.3 tha^-1, compared to 5.4 tha^-1 in FMF. Without accounting for between- and within-field variations, there was no relationship between UAV-derived VIs and grain yield at 4WAS (r<0.02, P>0.1), but significant correlations were observed at 8WAS (r≤0.3; p<0.001). Ht was positively correlated with grain yield at 4WAS (r=0.5, R²=0.25, p<0.001), and more strongly at 8WAS (r=0.7, R²=0.55, p<0.001), while relationship between CC and yield was only significant at 8WAS. By accounting for within- and between-field variations in NOTs and FMF (separately) through linear mixed-effects modeling, predictability of grain yield from UAV-derived VIs was generally (R²≤0.24), however, the inclusion of ground-measured biophysical variable (mainly Ht) improved the explained yield variability (R² ≥0.62, RMSEP≤0.35) in NOTs but not in FMF. We conclude that yield prediction with UAV-acquired imageries (before harvest) is more reliable under controlled experimental conditions (NOTs), than in actual farmer-managed fields where various confounding agronomic factors can amplify noise-signal within the vegetation canopy.

In this work, we show that a late fusion approach to multi-modality in sign language recognition improves the overall ability of the model in comparison to the singular approaches of Computer Vision (88.14%) and Leap Motion data classification (72.73%). With a large synchronous dataset of 18 BSL gestures collected from multiple subjects, two deep neural networks are benchmarked and compared to derive a best topology for each. The Vision model is implemented by a CNN and optimised MLP and the Leap Motion model is implemented by an evolutionary optimised deep MLP topology search. Next, the two best networks are fused for synchronised processing which results in a better overall result (94.44%) since complementary features are learnt in addition to the original task. The hypothesis is further supported by application of the three models to a set of completely unseen data where a multi-modality approach achieves the best results relative to the single sensor method. When transfer learning with the weights trained via BSL, all three models outperform standard random weight distribution when classifying ASL, and the best model overall for ASL classification was the transfer learning multi-modality approach which scored 82.55% accuracy.

Urgent environmental challenges and emerging additive manufacturing (AM) technologies push research towards more performant and new materials. In the field of metallurgy, high entropy alloys (HEAs) have recently represented a topic of intense research because of their promising properties, such as high temperature strength and stability. Moreover, this class of multi-principal element alloys (MPEAs) have opened up researcher community to unexplored compositional spaces, making prosper literature of high-throughput methodologies and tools for rapidly screening large number of alloys. However, none of the methods has been aimed to design new MPEAs for AM process known as selective laser melting (SLM) so far. Here we conducted nanoindentation testing on single scan tracks of elemental powder blends and pre-alloyed powders after ball milling of AlTiCuNb and AlTiVNb. Results show that nanoindentation can represent an effective technique to gain information about phase evolution during laser scanning, contributing to accelerate the development of new MPEAs.

(S)-Atenolol ((S)-2-(4-(2-Hydroxy-3-(isopropylamino)propoxy)phenyl)acetamide) has been synthesized in >99% ee with use of Candida antarctica lipase B from Syncozymes (Shanghai, China), in a kinetic resolution of the corresponding racemic chlorohydrin. Deprotonation of the starting phenol building block was base catalyzed. The enantiopurity of the chlorohydrin building block remained unchanged upon subsequent amination. All four steps in the synthesis protocol have been optimized compared to previously reported methods, which makes this new protocol more sustainable and in accordance with green chemistry principles compared to previously reported protocols.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

Abstract: Thermal desalination is yet a reliable technology in the treatment of brackish water and seawater; however, its demanding high energy requirements have lagged it compared to other non-thermal technologies such as reverse osmosis. This review provides an outline of the development and trends of the three most commercially used thermal or phase change technologies worldwide: Multi Effect Distillation (MED), Multi Stage Flash (MSF), and Vapor Compression Distillation (VCD). First, state of water stress suffered by regions with little fresh water availability and existing desalination technologies that could become an alternative solution are shown. The most recent studies published for each commercial thermal technology are presented, focusing on optimizing the desalination process, improving efficiencies, and reducing energy demands. Then, an overview of the use of renewable energy and its potential for integration into both commercial and non-commercial desalination systems is shown. Finally, research trends and their orientation towards hybridization of technologies and use of renewable energies as a relevant alternative to the current problems of brackish water desalination are discussed. This reflective and updated review will help researchers to have a detailed state of the art of the subject and to have a starting point for their research, since current advances and trends on thermal desalination are shown.

Water area segmentation in remote sensing is of great importance for flood monitoring. To overcome some challenges in this task, we construct the Water Index and Polarization Information (WIPI) multi-modality dataset and propose a multi-Modality Fusion and Gated multi-Filter U-Net (MFGF-UNet) convolutional neural network. The WIPI dataset enhances the water information and reduces the data dimension. In particular, the Cloud-Free label provided in the database effectively mitigates the issue of scarcity of labeled samples Since a single form or uniform kernel size cannot handle the variety in size and shape of water bodies, we proposed the gated multi-filter inception (GMF-Inception) module in our MFGF-UNet. Moreover, we utilize the attention mechanism by introducing the Gated Channel Transform (GCT) skip connection and integrating GCT into GMF- Inception to further improve model performance. Extensive experiments on three benchmarks, including WIPI, Chengdu and GF2020 datasets demonstrate that our method achieves favorable performance with lower complexity and better robustness against six competing approaches. For example, on WIPI, Chengdu and GF2020 datasets, the proposed MFGF-UNet model achieves F1 of 0.9191, 0.7410, and 0.8421, respectively, which average F1 on three datasets is 0.0045 higher than the U-Net model and reduces 62% average GFLOPs. New WIPI dataset, code and trained models have been released on GitHub

Real-world optimization problems are often governed by one or more constraints. Over the last few decades, extensive research has been performed in Constrained Optimization Problems (COPs) fueled by advances in computational intelligence. In particular, Evolutionary Algorithms (EAs) are a preferred tool for practitioners for solving these COPs within practicable time limits. We propose an ensemble of multi- method hybrid EA framework with four mutation operators, two crossover operators, multi-search [Differential Evolution (DE) & Gaining Sharing Knowledge (GSK)] optimization algorithm, and ensemble of constraint handling techniques to solve global real- world constrained optimization problem. The proposed frame- work FEPEA has an ascendancy of multiple adaptation strategies concerning the control parameters, search mechanisms, two sub-populations as well as uses knowledge sharing mechanism between junior and senior phases. The algorithm also combines the power of four popular constraint handling techniques (CHT) and uses a voting mechanism to select any particular CHT. On top of that, this algorithm also uses both linear and non- linear population size reduction in every step of the evolutionary process. We test our method on 57 real-world problems provided as part of the CEC 2020 special session & competition on real- world constrained optimization benchmark suite. Experimental results indicate that FEPEA is able to achieve state-of-the- art performance on real-world constrained global optimization when compared against other well-known real-world constrained optimizers.

The hybrid bond graph has been studied in depth for scalar bond graphs, but how does this translate to the multi-bond graph? Here, the controlled junction – used to model structural switching such as contact – is extended to the multi-bond case. This is a simple process, assuming that all bonds switch simultaneously (which makes physical sense). A controlled 0-junction is applied to multi-bond graph of a car, which can lose contact with the ground in cornering. Dynamic causality features, but this can be accommodated using an equational submodel in 20-Sim (in a manner similar to that used with scalar bond graphs). The junction is proposed for subsequent work to develop a validated multi-body dynamics car model in cornering.

The quality of digital elevation models (DEMs) is inevitably affected by the limitations of the imaging modes and the generation methods. One effective way to solve this problem is to merge the available datasets through data fusion. In this paper, a fusion-based global DEM dataset (82°S-82°N) is introduced, which we refer to as GSDEM-30. This is a 30-m DEM mainly reconstructed from the unfilled SRTM1, AW3D30, and ASTER GDEM v2 datasets combining the multi-source and multi-scale fusion techniques. A comprehensive evaluation of the GSDEM-30 data, as well as the 30-m ASTER GDEM v2 and AW3D30 DEM, was presented. Global ICESat GLAS data and the local National Elevation Dataset (NED) were used as the reference for the vertical accuracy validation, while GlobeLand30 was introduced for the landscape analysis. Furthermore, we employed the maximum slope approach to detect the potential artefacts in the DEMs. The results show that the GDEM data are seriously affected by noise and artefacts. With the advantage of the multiple datasets and the refined post-processing, the GSDEM-30 are contaminated with fewer anomalies than both ASTER GDEM and AW3D30. The fusion techniques used can also be applied to the reconstruction of other fused DEM datasets.

The framework of product life cycle (PLC) cost analysis is one of the most important evaluation tools for a contemporary high-tech company in an increasingly competitive market environment. The PLC-purchasing strategy provides the framework for a procurement plan and examines the sourcing strategy of a firm. The marketing literature emphasizes that ongoing technological change and shortened life cycles are important elements in commercial organizations. From a strategic viewpoint, the vendor has an important position between supplier, buyer and manufacturer. The buyer seeks to procure the products from a set of vendors to take advantage of economies of scale and to exploit opportunities for strategic relationships. However, previous studies have seldom considered vendor selection (VS) based on PLC cost (VSPLCC) analysis. The purpose of this paper is to solve the VSPLCC problems considering the situation of a single-buyer-multiple-supplier. For this issue, a new VSPLCC procurement model and solution procedure are derived by this paper to minimize net cost, rejection rate, late delivery and PLC cost subject to vendor capacities and budget constraints. Moreover, a real case in Taiwan is provided to show how to solve the VSPLCC procurement problem.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

In order to perceive the behavior presented by the multiphase chemical reactors, the ant colony optimization algorithm was combined with computational fluid dynamics (CFD) data. This intelligent algorithm creates a probabilistic technique for computing flow and it can predict various levels of three-dimensional bubble column reactor (BCR). This artificial ant algorithm is mimicking real ant behavior. This method can anticipate the flow characteristics in the reactor using almost 30 % of the whole data in the domain. Following discovering the suitable parameters, the method is used for predicting the points not being simulated with CFD, which represent mesh refinement of Ant colony method. In addition, it is possible to anticipate the bubble-column reactors in the absence of numerical results or training of exact values of evaluated data. The major benefits include reduced computational costs and time savings. The results show a great agreement between ant colony prediction and CFD outputs in different sections of the BCR. The combination of ant colony system and neural network framework can provide the smart structure to estimate biological and nature physics base phenomena. The ant colony optimization algorithm (ACO) framework based on ant behavior can solve all local mathematical answers throughout 3D bubble column reactor. The integration of all local answers can provide the overall solution in the reactor for different characteristics. This new overview of modelling can illustrate new sight into biological behavior in nature.

Improving air quality and reducing human exposure to unhealthy levels of airborne chemicals are important global missions, particularly in China. Satellite remote sensing offers a powerful tool to examine regional trends in NO2, thus providing a direct measure of key parameters that strongly affect surface air quality. To accurately resolve spatial gradients in NO2 concentration using satellite observations and thus understand local and regional aspects of air quality, a priori input data at sufficiently high spatial and temporal resolution to account for pixel-to-pixel variability in the characteristics of the land and atmosphere are required. In this paper, we adapt the Berkeley High Resolution product (BEHR v3.0A, v3.0B and v3.0C) and meteorological outputs from the Weather Research and Forecasting (WRF) model to describe column NO2 in southern China. The BEHR approach is particularly useful for places with large spatial variabilities and terrain height differences such as China. We retrieved tropospheric NO2 vertical column density (TVCD) within part of southern China, for four seasons of 2015, based upon satellite datasets from Ozone Monitoring Instrument (OMI). Retrieval results are validated by comparing with MAX-DOAS tropospheric column measurements conducted in Guangzhou. BEHR retrieval algorithms are more consistent with MAX-DOAS measurements than OMI-NASA retrieval, opening new windows into research questions that require high spatial resolution, for example retrieving NO2 vertical column and ground pollutant concentration in China and other countries.

Fragmentation processes of multiply charged ions of C10H8 isomers produced in fast proton collision (velocity between 1.41 and 2.4 a.u.) is discussed in view of their fundamental molecular dynamics. Especially so in the mechanisms to produce a variety of carbon clusters from such ions. This aspect is assessed with the help of a multihit analysis of daughter ions in coincidence with elimination of H+ and CHn+ (n = 0 to 3). The elimination of H+/C+ was found to be very different from CH3+ loss. The loss of CH3+ was found to be accompanied with the formation of heavy ions like C9H5+, C9H5++ and C7H3+ by a cascade of momentum correlated dissociations. The most probable structures of large fragment ions in the CH3+ loss cascade are predicted with the help of computed electronic energy and the multihit ToF correlations of second and third hit. In addition, we report observation of super-dehydrogenation of naphthalene and azulene targets, with evidence of complete dehydrogenation in a single collision.

This paper proposes a multi-terminal adaptive collaborative operation method to solve the problem of unstable internal force tracking in clamping and handling unknown objects by multi-terminal robots. In the proposed method, the internal command force changes the complex internal force control problem into an internal force tracking problem from multi-slave to master. Moreover, we develop an algorithm for multi-slave setups to estimate object stiffness and motion uncertainty in the direction of the internal command force according to Lyapunov theory. Finally, the impedance control generates a reference trajectory for the multi-slave to maintain the desired internal force and track the master’s motion. Several experiments are conducted on a self-made robot equipped. The experimental results show that the oscillation amplitude of each slave end is less than 1 mm, the directional oscillation amplitude is less than 1 degree during the tracking of the desired commanded internal force. For objects with low stiffness, the error of the commanded internal force is less than 1 N (6%) per slave. The error in tracking the commanded internal force for objects with high stiffness is less than 2 N (8%). The results prove the feasibility and effectiveness of the proposed method.

In gravitational theory and astrophysical dynamics, singular initial value problems (IVPs) are frequently encountered. Finding the solutions to this class of IVPs can be challenging due to their complex nature. This study strives to circumvent the complexity by proposing a numerical method for solving such problems. The approach proposed in the current research seeks solutions to the IVP by partitioning the domain [0,L] of the problem into two intervals and solving the problem on each domain. The study seeks a closed-form solution to the IVP in the interval containing the singular point. A linearization technique and piecewise partitioning of the domain not containing the singularity are applied to the nonlinear IVP. The resulting linearized differential equation is solved using the Chebyshev spectral collocation method. Some examples are presented to illustrate the efficiency of the proposed method. Numerical analysis of the solution and residual errors are shown to ascertain convergence and accuracy. The results suggest that the technique gives accurate convergent solutions using a few collocation points.

Dracunculiasis (also known as Guinea worm disease) is caused by Dracunculus medinensis parasite and it spreads by drinking water containing Larvae of Guinea worm. The lack of safe water facilities, preventions and treatments resulted in highly dangerous consequences in its endemic regions. The economy of the affected regions totally falls down due to less production which is the result of agricultural field worker’s bad health. In this study, a multi epitope vaccine was designed against Dracunculus medinensis by using immune-informatics. The vaccine was designed by using T-Cell and B-Cell epitopes derived from Dracunculus medinensis proteins (Lactamase-B domain-containing protein, G-Domain containing protein and Ferrochelatase) in addition to Adjuvants and Linkers. The tertiary structure, physiochemical properties and immunogenic elements of vaccine were achieved. The validation of tertiary structure was accessed, and quality was achieved. In addition, the world coverage of parasite’s CTL and HTL epitopes is 95.61%. The stability of the chimeric vaccine was achieved through disulfide engineering. The molecular docking with Toll Like Receptor 4 (TLR-4) of vaccine showed its binding efficiency followed by Molecular Dynamic Simulation. The immune simulation suggested the mediated cell immunity and repeated antigen clearance. At the end, the optimized codon was used in in silico cloning to ensure vaccine’s higher exposure in bacterium E. coli strain K12. With further assessments, it is believed that the proposed multi epitope vaccine has strong immunogen to control Dracunculus medinensis which may result in better social and economic conditions of endemic regions.

Introduction Tuberculosis is common in Pakistan. Due to various factors including socioeconomic factors, compliance is poor to anti-tuberculosis drugs, leading to resistance. We aim to determine the prevalence of Multidrug resistance (MDR) tuberculosis in Pakistani population.Methods A prospective observational study was conducted from April 1, 2019, to December 31, 2019, in the Pulmonology department of a tertiary care hospital in Pakistan. Culture and sensitivity were assessed using a sputum sample or, in cases of an absent sputum sample, from Broncho alveolar lavage.ResultsApproximately 71.3% percent patients who had tuberculosis were found to be resistant to Isoniazid and around 48.6% did not respond to Rifampin. Multi-drug resistant was found in 29.4% participants.ConclusionMulti-drug resistance tuberculosis is very prevalent in Pakistan, which may increase burden on health care system and may lead to various complications of tuberculosis.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

In the framework of maritime surveillance, vessel detection techniques based on spaceborne Synthetic Aperture Radar (SAR) images have promoted extensive applications for the effective understanding of unlawful activities at sea. The paper deal with this topic presenting a novel approach exploiting a cascade application of a pre-screening, and discrimination phase. The latter leverage the SAR spectrum by means of sub-looks analysis. For the first time, the method has been validated with experiments on multi-frequency (C-, X-, and L-band) SAR images. For a future syngergic exploitation of more SAR missions, the developed dataset, composed of Sentinel-1, SAOCOM and COSMO-SkyMed images, is comprehensive of multiple images gathered over the same area with short time lag (below 15 minutes). Finally, the diversified processing chains and the results for each mission product and scenarios are discussed. Being the first dataset of SLC (Single Look Complex) SAR multi-frequency data, the present work intends to encourage additional research in this promising field of research.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

All empirical water column correction methods have consistently been reported to require existing depth sounding data for the purpose of calibrating a simple depth retrieval model; they yield poor results over very bright or very dark bottoms. In contrast, we set out to (i) use only the relative radiance data in the image along with published data, and several new assumptions, (ii) in order to specify and operate the simplified radiative transfer equation (RTE), (iii) for the purpose of retrieving both the satellite derived bathymetry (SDB) and the water column corrected spectral reflectance over shallow seabeds. Sea truth regressions show that SDB depths retrieved by the method only need tide correction. Therefore it shall be demonstrated that, under such new assumptions, there is no need (i) for formal atmospheric correction, (ii) nor for conversion of relative radiance into calibrated reflectance , (iii) nor for existing depth sounding data, to specify the simplified RTE and produce both SDB and spectral water column corrected radiance ready for bottom typing. Moreover, the use of the panchromatic band for that purpose is introduced. Altogether, we named this process the Self-Calibrated Supervised Spectral Shallow-sea Modeler (4SM). This approach requires a trained practitioner, though, to produce its results within hours of downloading the raw image. The ideal raw image should be a “near-nadir” view, exhibit homogeneous atmosphere and water column, include some coverage of optically deep waters and bare land, and lend itself to quality removal of haze, atmospheric adjacency effect, and sun/sky glint.

In this article, we introduce some multi-messenger studies of blazars. Main contents contain the following parts, 1. the subclasses of blazars and the observational characteristics, 2. emission variabilities from the multi-messenger observations, 3. the physical origin for the multi-messenger studies. Based on mid-IR observations collected from the $WISE$ database, we collect two sources (BZQ J1700+6830 and BZQ J1842+6809) to analyze the mid-IR variabilities. \\ (1) For BZQ J1700+6830, the period is $P\approx$ 42 hr at the four bands ($W1$, $W2$, $W3$, $W4$); for BZQ J1842+6809, the period is $P\approx$ 123 hr at the two bands ($W1$, $W2$). \\ (2) Using the periodicities, we calculate that the central black hole mass ($BH$) should be $M = (5.44\sim33.0)\times10^8M_{\odot}$ for BZQ J1700+6830 and $M = (1.13\sim6.88)\times10^9M_{\odot}$ for BZQ J1842+6809.\\ (3) For the two sources, during the flaring stage, we find anti-clockwise variation trends based on the time-based relations built by the spectral indices ($\alpha$) and flux densities ($F$).\\ (4) We calculate the Doppler factor ($\delta$) when the sources are in the dimming or brightening stages, and find that with the frequency increasing, the Doppler factor become stronger.

The paper considers new effects of the nanoscale state of matter, which open up prospects for the creation of electronic devices using new physical principles. The contact of chemically homogeneous different sizes hydrated nanoparticles of yttrium-stabilized zirconium oxide (ZrO2 – x %mol Y2O3, x=0, 3, 4, 8; YSZ) with particle sizes of 7.5 nm and 7,5 nm; 7.5 nm and 9 nm; 7.5 nm and 11 nm; 7.5 nm and 14 nm in the form of compacts obtained using high hydrostatic pressure (HP-compacts of 300MPa) was studied at direct and alternating current. A unique size effect of the nonlinear (semiconductor) dependence of the electrical properties (in the region U <2.5 V, I ≤ 2.7 mA) of the contact of different-sized YSZ nanoparticles of the same chemical composition is revealed, which indicates the possibility of creating semiconductor structures of a new type based on chemically homogeneous nanostructured systems. The electronic structure of the near-surface regions of nanoparticles of a special type of oxide materials and the possibility, on this basis, to obtain specifically rectifying properties of the contacts were studied theoretically. Models of surface states of the Tamm type are constructed, but considering the Coulomb long-range action. The discovered variance and its dependence on the curvature of the surface of nanoparticles made it possible to study the conditions for the formation of a contact potential difference in cases of nanoparticles of the same radius (synergistic effect), different radii (doped and undoped variants), as well as to discover the possibility of describing a group of powder particles from material within the Anderson model. The established effect makes it possible to solve the problem of diffusion instability of semiconductor heterojunctions and opens up prospects for creating electronics devices with a fundamentally new level of properties for use in various fields of the national economy and breakthrough critical technologies.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

Our work uses Iterative Boltzmann Inversion (IBI) to study the coarse-grained interaction between 20 amino acids and the representative carbon nanotube CNT55L3. IBI is a multi-scale simulation method that has attracted the attention of many researchers in recent years. It can effectively modify the coarse-grained model derived from the Potential of Mean Force (PMF). IBI is based on the distribution result obtained by All-Atom molecular dynamics simulation, that is, the target distribution function, the PMF potential energy is extracted, and then the initial potential energy extracted by the PMF is used to perform simulation iterations using IBI. Our research results have gone through more than 100 iterations, and finally, the distribution obtained by coarse-grained molecular simulation (CGMD) can effectively overlap with the results of all-atom molecular dynamics simulation (AAMD). In addition, our work lays the foundation for the study of force fields for the simulation of the coarse-graining of super-large proteins and other important nanoparticles.

Multi-morbidity and polypharmacy are common in older people and pose a challenge for health and social care systems especially in context of global population ageing. They are complex and interrelated concepts in the care of older people that require early detection and patient centred decision making that are underpinned by the principles of multidisciplinary led comprehensive geriatric assessment (CGA). Personalised care plans need to remain responsive and adaptable to the needs of a patient, enabling an individual to maintain their independence.

This paper presents a new and enhanced fusion module for the Multi-Sensor Precipitation Estimator (MPE) that would objectively blend real-time satellite quantitative precipitation estimates (SQPE) with radar and gauge estimates. This module consists of a preprocessor that mitigates systematic bias in SQPE, and a two-way blending routine that statistically fuses adjusted SQPE with radar estimates. The preprocessor not only corrects systematic bias in SQPE, but also improves the spatial distribution of precipitation based on SQPE and makes it closely resemble that of radar-based observations. It uses a more sophisticated radar-satellite merging technique to blend preprocessed datasets, and provides a better overall QPE product. The performance of the new satellite-radar-gauge blending module is assessed using independent rain gauge data over a 5-year period between 2003-2007, and the assessment evaluates the accuracy of newly developed satellite-radar-gauge (SRG) blended products versus that of radar-gauge products (which represents MPE algorithm currently used in the NWS operations) over two regions: I) inside radar effective coverage and II) immediately outside radar coverage. The outcomes of the evaluation indicate a) ingest of SQPE over areas within effective radar coverage improve the quality of QPE by mitigating the errors in radar estimates in region I; and b) blending of radar, gauge, and satellite estimates over region II leads to reduction of errors relative to bias-corrected SQPE. In addition, the new module alleviates the discontinuities along the boundaries of radar effective coverage otherwise seen when SQPE is used directly to fill the areas outside of effective radar coverage.

Bioelectrocatalysis provides the intrinsic catalytic-functions of redox enzymes to non-specific electrode reactions and is the most important and basic concept for biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multi-analyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination.

This article proposes the use of a multi-scale and multi-sensor approach to collect and modelling 3D data concerning wide and complex areas in order to obtain a variety of metric information in the same 3D archive, based on a single coordinate system. The employment of these 3D georeferenced products is multifaceted and the fusion or integration among different sensors data, scales and resolutions is promising and could be useful for the generation of a model that could be defined as hybrid. The correct geometry, accuracy, radiometry and weight of the data models are hereby evaluated comparing integrated processes and results from Terrestrial Laser Scanner (TLS), Mobile Mapping System (MMS), Unmanned Aerial Vehicle (UAV), terrestrial photogrammetry, using Total Station (TS) and Global Navigation Satellite System (GNSS) as topographic survey. The entire analysis underlines the potentiality of the integration and fusion of different solutions and is a crucial part of the “Torino 1911” project whose main purpose is mapping and virtually reconstructing the 1911 Great Exhibition settled in the Valentino Park in Turin (Italy).

Does cell clustering influence intrinsic and acquired multi-drug resistance (MDR) differently? To address this question, we studied cultured monolayers (representing individual cells) and cultured spheroids (representing clusters) formed by drug-naïve (intrinsic MDR) and drug-exposed (acquired MDR) lines of ovarian cancer A2780 cells by cytometry of reaction rate constant (CRRC). MDR efflux was characterized by accurate and robust “cell number vs. MDR efflux rate constant (kMDR)” histograms. Both drug-naïve and drug-exposed monolayer cells presented unimodal histograms; the histogram of drug-exposed cells was shifted towards higher kMDR value suggesting greater MDR activity. Spheroids of drug-naïve cells presented a bimodal histogram indicating the presence of two subpopulations with different MDR activity. In contrast, spheroids of drug-exposed cells presented a unimodal histogram qualitatively similar to that of the monolayers of drug-exposed cells but with a moderate shift towards greater MDR activity. The observed greater effect of cell clustering on intrinsic than on acquired MDR can help guide the development of new therapeutic strategies targeting clusters of circulating tumor cells.

In this paper, we consider a new class of polynomials which is called the multi-poly-Euler polynomials. Then, we investigate their some properties and relations. We provide that the type 2 degenerate multi-poly-Euler polynomials equals a linear combination of the degenerate Euler polynomials of higher order and the degenerate Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Euler polynomials and degenerate Whitney numbers.