Manufactured sand and natural sand have great differences in terms of physical properties, chemical composition, and so on. In the mix ratio design of manufactured sand concrete, the traditional common concrete ratio cannot be used. The water-cement ratio playing a crucial role in the mix ratio design. The optimum water-cement ratio can not only improve concrete performance, it can also reduce cement consumption and costs. The present study examines the working performance indicators and mechanical performance indicators of manufactured sand concrete using Fujian granite with three strength grades (C35, C40 and C50) at different water-cement ratios. The impact of water-cement ratio on the operational and mechanical performance of manufactured sand concrete with different strength grades is analyzed and summarized. Revised sentence: The findings suggest that the workability of Fujian granite concrete is directly influenced by the water-cement ratio. Additionally, the water-cement ratio indirectly affects the mechanical properties of manufactured sand concrete. Finally, when changing the water-cement ratio, cube compressive strength, splitting tensile strength and bending strength exhibit similar trends. The optimal water-cement ratio for C35 concrete is determined to be 0.39, considering the workability and mechanical properties of Fujian granite manufactured sand concrete. Similarly, the optimal water-cement ratio for C40 concrete is 0.34, while for C50 concrete it is 0.32.

Structural evolution, mechanical and tribological properties of Al-Mg alloy admixed with 5, 10 and 15 vol.% of iron powder using multi-pass friction stir processing (FSP) have been studied. Homogeneous distribution of intermetallic compound (IMC) particles were achieved after 4 FSP passes what resulted in increasing the stir zone hardness and ultimate tensile stress with simultaneous loss in the ductility. The reinforcement of the aluminum alloy matrix with IMCs allowed reducing wear at the same magnitude of friction. Subsurface composite tribological layer was formed on the FSPed samples as a result of rubbing against a steel counterbody.

Modular high-rise buildings frequently adopt cast-in-place concrete to ensure building integrity. To reduce the material consumption and realize mold-free casting, a 30 mm thick light concrete mold shell wall panel ( MiC wall panel) is set as part of the shear wall. But the concrete casting process is prone to cracking and rising pattern. Its force performance and damage mechanism is not clear. To this end, this paper designs three groups of MiC wall panels with different material component types. The static load test is carried out in a graded partitioned loading mode. The effects of different material components on the mechanical properties of MiC wall panels are systematically investigated and parametrically analyzed by numerical simulation. The results show that the front cracks of the wall slab are mainly distributed under the truss tendons, and the back cracks are mainly distributed in the span position of the adjacent truss tendons. They are both along the span direction of the wall slab. Increasing the strength level of concrete and using steel fiber concrete can improve the mechanical properties of MiC wall panels to different degrees. Among them, increasing the concrete strength has a significant effect on improving the load-bearing capacity of wall panels, while incorporating steel fibers can significantly improve the deformation and crack resistance of wall panels. By building more finite element models, it was verified that the steel fiber admixture has limited effect on the mechanical properties of wall panels as the concrete grade increases. This study aims to summarize the types of wall panels with the best working properties. It provides a practical basis for optimizing the production and fabrication process of MiC wall panels.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

In the last two decades, gelatin-based hydrogels have been widely used as tissue engineering scaffolds due to their excellent biocompatibility, biodegradability, easy processability, transparency, non-toxicity, and reasonable structural similarity to the natural extracellular matrix (ECM). However, intrinsic low mechanical properties of gelatin are not structurally and mechanically suitable to support cell growth and proliferation. That’s why various crosslinking strategies including physical, chemical, enzymatic and combination of them as well as networking patterns including double network, interpenetrating network and nano reinforcing mechanism have been utilized to enhance the structural stability and mechanical integrity of gelatin. In this review, the advances in modulating the mechanical properties of gelatin-based hydrogels for the design and development of structurally stable scaffolds for tissue engineering are discussed. The optimized crosslinking parameters with the adequate mechanical properties of gelatin-based hydrogels are reviewed. Gelatin-based scaffolds for a wide range of tissue engineering applications, such as bone, cartilage, cardiac, skin, and nerve tissue engineering are also outlined. Lastly, current challenges and future perspectives in this research field are presented.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

Currently, synthetic diamonds are finding new applications. Quantum devices can be created based on diamond plates with the desired concentration of defects in the structure of the crystal lattice. NV color centers can be used in quantum applications by irradiating plates with high-energy particles, followed by annealing at temperatures above 800°C to develop the spin-optical properties of the centers Diamond plates are subjected to electron irradiation and much less often to proton irradiation. As a result, synthetic diamond plates with NV centers ob-tained by proton irradiation are less studied, although proton irradiation makes it possible to obtain a layered structure of NV centers. In this work, single crystal diamond plates irradiated with protons were studied using polarization microscopy, IR spectroscopy and ODMR spectros-copy. It is shown that when creating NV centers, the distribution and concentration of C – defects in the sample, as well as mechanical stresses before and after irradiation (with subsequent an-nealing), can differ significantly from each other.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

The mechanical properties of α-chitin and chitosan biocomposite are investigated due to their broad range of potential applications in bioengineering, materials science, and environmental technology. Employing molecular dynamics (MD), and stress-strain analyses, this study comprehensively investigates biopolymers mechanical response and anisotropic mechanical behavior under uniaxial tensile loading conditions in an aqueous environment. Our computational models were validated against existing experimental data, showing high degrees of correspondence. Uniaxial tensile tests revealed that α-chitin exhibits a remarkable ultimate tensile strength (UTS) of 10.07 GPa in the crystalline chain direction (y-axis) at a high strain rate of 0.636, compared to a significantly lower UTS of 2.78 GPa in the perpendicular direction (x-axis) at a lower strain rate of 0.066. The biocomposite nanostructure, encompassing randomly distributed chitosan, reduced stiffness, maintaining remarkable flexibility as α-chitin, with a UTS of 5.03 GPa in the y-axis and 2.34 GPa in the x-axis. Further, the directional elastic modules for α-chitin were calculated as 51.76 GPa and 39.76 GPa in the x and y directions, respectively. In contrast, these values for the α-chitin-chitosan biocomposite were estimated as 31.66 GPa and 26.00 GPa, respectively. The findings provide valuable insights into the distinct mechanical properties of α-chitin and chitosan biocomposite, making a substantial contribution to optimizing these materials for specialized applications.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

This research aimed to determine the effect of alkaline treatment on zalacca midrib fiber (ZMF) concerning various aspects such as thermal stability, crystallinity index, interfacial bonding, interfacial shear strength, water absorption capacity, as well as conducting Scanning Electron Microscopy (SEM). This investigation extended to evaluating the mechanical properties of composites enriched with microcrystalline cellulose with prosthetic socket materials available on the market. Subsequently, ZMF was obtained by splitting and soaking zalacca midrib for 12 hours. Each of ZMF was removed from the midrib and soaked in 5% sodium hydroxide for 3, 6, 9, and 12 hours. The composite material was molded by mixing 10% microcrystalline cellulose with a rotational speed of 150 rpm, maintaining a temperature of 40°C, and continuing the mixing process for 30 minutes. As a result of the alkaline treatment, several positive effects were observed, including increased fiber density, improved particle bonding, increased thermal compatibility, and cleaner fiber surfaces, attributed to reduced levels of hemicellulose, lignin, pectin, and other impurities as confirmed by SEM analysis. The microcrystalline cellulose added to the composite increased the interfacial shear strength, and tensile strength increased by 56.74%, composite flexural strength increased by 76.43%. The SEM analysis results showed that the composite with ZMF on the base fiber broke during the tensile test because fiber experienced an increase in interfacial bonding between fiber and the matrix. The water absorption test showed that untreated fiber had a higher level of absorption

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Background: Number of joint infections caused by Vancomycin-resistant pathogens is emerging. Currently no PMMA cement is commercially available to cover VRE. Daptomycin shows promising results in infection treatment, offers a good safety profile and reduced risk for resistance development. Purpose of this in vitro study is to investigate the mechanical stability, handling properties, elution behavior and antimicrobial effectiveness of PMMA cement loaded with three different Daptomycin concentrations in comparison to commercially available ALBC; Methods: Mechanical properties and handling characteristics (ISO 5833, DIN 53435), HPLC elution, antimicrobial effectiveness with proliferation assay (DIN 17025) and inhibition zone testing were investigated; Results: All tested Daptomycin concentrations fulfilled ISO and DIN mechanical strength. Dosage of 0.5. g added Daptomycin did not show any antimicrobial effectiveness in contrast to 1.0 g and1.5 g. Cement with 1.5 g Daptomycin was best in elution and effectiveness, showed good mechanical ISO strength, ISO doughing was a little longer sticky and setting was faster as Vancomycin containing reference cement; Conclusion: PMMA cement containing 0.5 g Gentamicin and 1.5 g Daptomycin could be a good alternative to the already established COPAL® G+V for PJI treatment of VRE.

Chemical and mechanical properties of plasma-assisted nitrided (PAN), TiN cathodic arc coated, and PAN with TiN coated samples were thoroughly evaluated on tool steel samples of 1.2379. The evaluation involved SEM, nano-indentation, profilometer, micro scratch, and corrosion tests. The results revealed that PAN treatment alters the roughness of the surface, while it has minimal impact on the coefficient of friction. However, it increases the substrate's hardness, making it twice as hard and three times more resilient against scratch tests, along with improved corrosion resistance. TiN-coated samples are four times harder than untreated ones, but they exhibit a higher elastic modulus (E), leading to a lower H/E index. The most promising results were obtained with PAN+TiN treatment, combining high hardness (H) with lower E, resulting in a high H/E index, a crucial criterion for wear resistance. These samples also demonstrated superior scratch hardness and corrosion resistance, despite being thinner and rougher.

Entangled metallic wire material (EMWM) can be utilized as a novel elastic element in vibration isolation devices for mechanical actuators. This paper presents a vibration experiment aimed at investigating the degradation behavior of mechanical performance in EMWM under cyclic compressive environment. An electric vibration testing system, coupled with an isolation structure, is employed to apply compressive loads to the EMWM specimens. Through visual observations and quasi-static compression tests, the variations in geometric morphology and mechanical properties are studied, considering different relative densities and stress amplitudes. The results incidate a significant reduction in the compressed dimension of the specimens as the number of cycles increases, without any wire fractures or wear. Moreover, the mechanical properties exhibit an increasing secant modulus and a decreasing loss factor. These variations ultimately lead to a gradual deviation of the vibration characteristics of the isolation structure from its design state. To predict the mechanical property degradation of EMWM, prediction models are proposed, incorporating dimension, modulus and damping by fitting the obtained results. This research provides valuable experimental data and presents an effective method to determine the operational lifetime of vibration isolators utilizing EMWM.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

The changes in consumer lifestyles have raised awareness of the variety of food options and packaging technologies. Active and smart packaging represents an innovative technology that serves to enhance the safety and quality of products. Smart packaging, as a subset of this technology, entails the integration of additives into packaging materials, thereby facilitating the preservation or extension of product quality and shelf life. This technological approach stimulates a heightened demand for safer food products with prolonged shelf life. Active packaging predominantly relies on the utilization of natural active substances. Therefore, the combination of active substances has a significant impact on the characteristics of active packaging particularly on polymeric blend like Polylactic acid (PLA) as a matrix. So, This review will summarize and explains how the addition of natural active agents influenced the properties related to the performance of active packaging through systematic analysis, providing new insights about the relationship between the types of active agents on physical-mechanical properties, bacterial colony reduction, and applications in foods packaging such as meat, fish, fruit, and vegetables. Through their integration, the market for active and smart packaging systems is expected to have a bright future.

Mechanical ventilation systems used in houses are designed to reduce carbon dioxide emissions while minimizing the energy loss resulting from ventilation. However, increase in indoor fine particulate (PM2.5) concentration because of external PM2.5, influx through the ventilation system poses a problem. In this study, we analyzed the changes in indoor PM2.5 concentrations via dis-tinguishing between cases of high and low outdoor PM2.5 concentrations, considering the effi-ciency of filters used in residential mechanical ventilation systems. When using minimum effi-ciency reporting value (MERV) 10 filters in the ventilation system, the outdoor PM2.5 concentra-tion was 5 μg/m³; the indoor PM2.5 concentration became 73% after 60 min compared to the ini-tial. When the outdoor PM2.5 concentration was 30–40 μg/m³, the indoor PM2.5 concentration reached 91%. However, when MERV 13 filters were used, the indoor PM2.5 concentration con-sistently dropped to 73–76% regardless of the outdoor PM2.5 concentration. Furthermore, by comparing the established equation with the mass-balance model, the error was confirmed to be within 5%, indicating good fit. This allows the prediction of indoor PM2.5 under various condi-tions when using mechanical ventilation systems, enabling the formulation of strategies to maintain indoor PM2.5 as recommended by the World Health Organization.

The phosphogypsum (PG) pile of solid waste is of immense proportions and poses a grave threat to the ecological environment, with its reserves steadily increasing year after year. The urgent need for large-scale consumption and high-quality utilization of PG in industrial production has become apparent. The present study provides a comprehensive analysis of the correlation be-tween the macroscopic mechanical properties and microstructure of PG, elucidating the crystal morphology characteristics in different phases and outlining the crystallization preparation pro-cess. By integrating the physical and chemical properties of diverse PG phases with the intricacies associated with its preparation process, it is imperative to explore avenues for its high-value utili-zation, investigate possibilities for industrial-scale production, and analyze and predict the appli-cation trends and developmental directions in comprehensive PG utilization. These endeavors hold immense significance in guiding the realization of resource utilization potential inherent in PG.

A medium-Mn steel was processed by a route involving twin-roll strip casting, hot-rolling and quenching and partitioning with different quenching temperatures. The effects of quenching temperature on the microstructure and mechanical properties were studied. It was found primary martensite and retained austenite (RA) were obtained at the quenching temperature of 140–180 °C, while primary martensite, RA and secondary martensite were obtained when the quenching temperature was 220–300 °C. With increase in quenching temperature from 140 to 260 and to 300 °C, RA fraction first increased from 15.4% to 31.8% and then decreased to 16.6%. The sample at quenching temperature of 220 °C yielded the mechanical properties with yield strength of 992 MPa, tensile strength of 1159 MPa and total elongation of 20.4%. The superior mechanical properties were achieved by an optimum combination of high RA fraction (26.5 vol%), appropriate mechanical stability of RA and a small amount of secondary martensite.

Neat polyimide films are known to be dense and rigid. They are therefore not suitable for use in membranes, sensors and sustainable energy storage applications. In this study a novel technique has been used to simulta-neously improve the rigidity, damping ability and impact resistance of polyimide membranes. It is demonstrated that dispersion of a small amount of polyaniline copolymer-modified clay of about 0.25-0.5 wt.% into the pol-yimide matrix, resulted in enhanced storage modulus while maintaining high damping ability and glass transition temperature, Tg. Novel polyimide/substituted polyaniline-copolymer-clay nanocomposite membranes containing poly(N-ethyl-aniline-co-aniline-2-sulfonic-acid-modified-clay (SPNEAC) was successfully prepared and in-corporated into polyimide matrix to form modified clay/polyimide nanocomposites. UV-Vis analysis of the nanocomposite films show that the optical transparency of the SPNEAC-PI nanocomposite membranes de-creased with increasing SPNEAC concentration due to the high UV-Vis absorption of SPNEAC. Transmittance of about 3 % was observed in the nanocomposite membrane containing 5wt.% modified clay at 500 nm wave-length, which is significantly lower than that for the neat PI membrane of about 36 %. The dispersion of SPNEAC containing high concentration of clay (≥ 40 wt.% clay), SPNEAC2 in polyimide matrix, resulted in attainment of a higher degree of imidization than was possible for the neat organoclay/polyimide nanocomposite. This behavior is believed to be due to the synergistic interaction between PI and polyaniline copolymer modified clay. The viscoelastic property of polyimide and the nanocomposite membranes was measured by using the dynamic mechanical spectroscopy, DMS. It was shown that the glass transition temperature, Tg of the nano-composites decreased, while the damping ability and impact energy increased with increasing weight fraction of fillers.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

Studies have shown the benefits of endovascular treatment (EVT) in adult stroke cases, but its application in pediatric stroke remains controversial. Despite evidence of improved outcomes in adults, there are no established recommendations for EVT in children. Conducting individual case reports and case series is vital to understanding its potential advantages and disadvantages in this context. This case report presents a 9-year-old boy who experienced basilar artery occlusion leading to a stroke and was effectively treated with mechanical thrombectomy.

Graphyne is a material that has unique mechanical properties, but little is known about how these properties change when the material has holes. In this work, the effect of hole geometry, considering circular, triangle, and rhombus hole configurations, on the mechanical nonlinear response of γ-graphyne structures is studied. Graphyne, graphdiyne, graphyne-3, and graphyne-4 structures are under investigation. An efficient nonlinear finite element analysis (FEA) method is adequately implemented under large deformations for this purpose. The study varied the size and shape of the holes to understand how these changes affect the nanostructure's mechanical response. The results indicate that the hole geometry significantly impacts the mechanical nonlinear response of γ-graphyne structures. The holes' size and shape affect the structures' elastic behavior, deformation, and strength. The findings can be used to optimize the design of γ-graphyne structures for specific mechanical applications. The study highlights the importance of considering the hole geometries in the design and fabrication of these materials.

Mechanical circulatory support has proven effective in managing postcardiotomy cardiogenic shock by stabilizing patients' hemodynamics and ensuring adequate organ perfusion. Among the available device modalities, the combination of extracorporeal life support and a microaxial flow pump for left ventricular unloading has emerged as a valuable tool in the surgical arma-mentarium. In this publication, we provide recommendations for the application and weaning of temporary mechanical circulatory support in cardiogenic shock patients, derived from a con-sensus among leading cardiac centers in German-speaking countrie

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

In 1911, A. Einstein suggested that gravity affects at the electromagnetic radiation originating from the distant sources, namely, it shifts the spectral lines in the red side of the spectrum and derived the gravitational redshift formula. A modern science claims that Einstein’s formula is mathematically immaculate. We show that this is not true: in fact, this formula is approximate. Using the law of conservation of mechanical energy, we derived two exact formulas оf the gravitational redshift.

The flavor, aroma and color of coffee may change due to mechanical damage, reducing its qual-ity. To measure the mechanical response of materials, compression tests can be performed, de-termining the effect of force application on the mechanical behavior of the fruit at different stages of ripeness. In this context, this study aimed to analyze the deformation, strain energy and equivalent von Mises stress of coffee fruits at mature, semi-mature and immature maturation stages and compressed by collapse forces. Compression in three directions (x, y and z) was sim-ulated on coffee fruit models using the finite element method, with a compression support in the direction opposite to the force application axis. The numerical simulation of the compression process allowed to verify that the more mature the fruit, the greater the associated mean defor-mation (2.20 mm mm-1, 0.78 mm mm-1 and 0.88 mm mm-1), the lower the mean strain energy (0.07 mJ, 0.21 mJ and 0. 34 mJ) and the lower the mean equivalent von Mises stress (0.25 MPa, 1.03 MPa and 1.25 MPa), corresponding to ripe, semi-ripe and immature fruits; and these proper-ties may be used to analyze how processes in the production chain affect the amount of mechan-ical damage.

The present study aimed to evaluate the effect of the citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid over the physical properties of wood. After choosing the best treatments (170°C and 5% and 10% of citric acid) it was evaluated the effect of these on the chemical properties (SEM, FTIR and pH), on the density profile using an X-ray microtomography, and on the resistance to ageing through abrasion test. The result of the chemical analysis allowed to observe an increase of the presence of ester functional groups, as well as a better coverage and higher acidity of the surface. The density profile technique allowed to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasion because of the application of the citric acid.

Abstract: The chemical mechanical polishing (CMP) has been widely used for surface modification of critical materials and components and provided global planarization of topography with a low post-planarization slope high quality and efficiency. The colloidal silica slurries play an important role in the finishing processes of optical components. Monodisperse mesoporous silica nanospheres were synthesized with different surfactant by Stöber method. Their architectural features and texture parameters were characterized by XRD, FTIR, N2 adsorption–desorption isotherms, SEM, XPS, and TGA techniques. The spherical SiO2 products presented with the controllable 50-150 nm particle size and distribution. The AFM micrographs reveal that flat and smooth surfaces without distinct scratches residual particles are achieved by using the as-obtained composite particles as abrasives[The particle size of SiO2 slurry plays a critical role in the chemical-mechanical polishing process.

Microelectromechanical System (MEMS) vibrating gyroscope design considerations are always intriguing due to their microscale mechanical, electrical, and material behavior. MEMS vibrating ring gyroscopes have become important inertial sensors in inertial measurement units (IMU) for navigation and sensing applications. The design of a MEMS vibrating ring gyroscope incorporates an oscillating ring structure as a proof mass, reflecting unique design challenges and possibilities. This paper presents a comprehensive design analysis of the MEMS vibrating ring gyroscope from the mechanical, electrical, and damping perspectives. The mechanical design of the MEMS vibrating ring gyroscope investigates the various frame designs of the vibrating ring structure, as well as the various beam structures, including curved, rectangular, and semicircular beam structures, which are analyzed using mathematical models and finite element analysis (FEA) simulations that provide an in-depth analysis of the stiffness and deflection of the vibrating structures. The electrical designs of the MEMS vibrating ring gyroscope were analyzed using various electrode configurations, electrostatic actuation, and capacitive detection mechanisms, respectively. The design analysis of various forms of damping, including viscous, structural, thermoelastic, and anchor damping, has been discussed. The variety of design structures investigated for MEMS vibrating ring gyroscopes' mechanical, electrical, and damping performance.

Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m3) can be enhanced by approximately 484% in a composite (56.86 MJ/m3) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.

Sulfur, peroxide and combined sulfur and peroxide curing systems were applied for cross-linking of unfilled and carbon black filled rubber compounds based on ethylene-propylene-diene-monomer rubber. The results revealed that the type of curing system influenced the course and shape of curing isotherms. This resulted in the change of curing kinetics of rubber compounds. The cross-link density of vulcanizates cured with combined vulcanization systems was lower than that for vulcanizates cured only in the presence of sulfur or peroxide system. The results revealed good correlation between the cross-link density as well as the structure of the formed cross-links and physical-mechanical characteristics of the materials. It can be stated that by proper combination of vulcanization systems it is possible to modify tensile behavior of vulcanizates in targeted manner. On the other side, dynamical-mechanical properties were found not be significantly influenced by the composition of curing system.

Several lime mortars for the repair of painted plasters of the rock cut church of Ss. Pietro and Paolo in Matera were studied. They were designed taking into account both aesthetic criteria that need to be fulfilled in the field of paintings restoration, and physical-mechanical compatibility with the original materials on site, i.e. the pre-existing plasters and the supporting rock. Mixes with calcareous and silica aggregates, based on different grain size proportions, were prepared for filling missing portions of the original painted plaster. The effects of the mineralogical nature and size of the aggregates on the characteristics and properties of the mixes were investigated in relation to the microstructure, physical-mechanical features and resistance to salt ageing. At the end of the experimental campaign, the overall performances were evaluated.

In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

In recent times, the soft robotics field is gaining numerous research focus owing to its high level of manipulation capabilities unlike traditional rigid robots, which gives room for an increasing use in other areas. However, compared to traditional rigid gripper robots, being capable of controlling/obtaining overall body stiffness when required is yet to be further explored since soft gripper robots have inherently less rigid properties. unlike previous designs with very complex variable stiffness systems, this paper demonstrates a soft gripper design with minimum system complexity while being capable of varying the stiffness of a continuum soft robotic actuator and proves to have potential applications in gripping objects of various shapes, weights & sizes. The soft gripper actuator comprises two separate mechanisms; the pneumatic mechanism for bending control and the mechanical structure for stiffness variation by pulling tendons using stepper motors which compresses the actuator, thereby changing the overall stiffness. The pneumatic mechanism was first fabricated and then embedded into another silicon layer during which it was as well merged with the mechanical structure for stiffness control. By first pneumatically actuating the actuator which causes bending and then pulling the tendons, we found out that the actuator stiffness value can be increased up to 145 % its initial value, and the gripper can grasp & lift a weight of up to 2.075 kg.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

Cancer cells exhibit aberrant extracellular matrix mechanosensing due to altered expression of mechanosensory cytoskeletal proteins. Aberrant mechanosensing of the tumor microenvironment (TME) by cancer cells has been shown to be associated with cancer development and progression. Recent studies show that altered mechanosensing changes the mechanobiological properties of cells, and, in turn, cells become susceptible to mechanical perturbations. Due to an increasing understanding of cell biomechanics and cellular machinery, several approaches have emerged to target the mechanobiological properties of cancer cells and cancer-associated cells to inhibit cancer growth and progression. In this review, we summarize the progress that happened in the development of mechano-based approaches to target cancer by interfering with the cellular mechanosensing machinery and overall TME.

A CoCrFeNiNb0.65 eutectic high-entropy alloys (EHEAs) prepared by arc melting were irradiated with a 100 keV He+ ion beam. Swelling, helium bubbles and mechanical response induced by irradiation were evaluated. When the ion fluence reached 1.0×1018 ions/cm2, the irradiation-induced swelling occurred on the sample surface, and as the ion fluence increasing, the swelling became increasingly severe and the surface of Nb-rich phase appeared peeling and shedding. Meanwhile, along the boundaries of matrix and Nb-rich phase there was a neat line of helium bubbles. The size of these helium bubbles decreased with distance from the center of the helium bubble layer. This result indicated that the phase boundaries were favorable sites for the nucleation and gathering of helium bubbles. Nanoindentaion results indicated that hardening and softening induced by He+ ion irradiation occurred in various ion fluences. At ion fluence of 5.0×1017 ions/cm2, the CoCrFeNiNb0.65 EHEAs exhibited an obvious hardening behavior, which can be explained by dislocation-dominated hardening effect. When the ion fluence reached 1.0×1018 ions/cm2 and 2.0×1018 ions/cm2, the hardening effect decreased probably due to the helium bubble aggregation and growth, as well as helium bubbles induced noncompact structures. The results of this study provide insights into the effect of helium bubbles on mechanical evolution and pave the way for designing EHEAs suitable for the nuclear industry.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

For enhancing the efficiency of cantilever casting the construction in the bridge, a novel rhombus traveling track of hanging basket was developed and optimized. The civil software titled Midas was applied to analyse the mechanical properties of the hanging basket with full load and control load. The strength and distortion of the walking mechanism were within the specified range when the maximum beam unit internal force of 149.69Mpa, which was less than the allowable stress of steel 175Mpa, and the anti-overturning safety factor of the hanging basket was 2.5 to meet the requirements. Through the comparative analysis of the key components and the finite element calculation, it was found that there was about 30% redundancy in the structure performance. Therefore, further optimization of each structure was carried out, and the front elevation of the main truss of 20° was achieved. It obtained the best performance in all aspects.

In vivo, articular cartilage tissue is surrounded by a cartilage membrane, and HP (HP) and compressive strain increases simultaneously with the compressive stress. However, it has been impossible to investigate the effects of simultaneous loading in vitro. In this study, a bioreactor capable of applying compressive stress under HP was developed to reproduce ex vivo the same physical loading environment found in cartilage in vivo. First, a HP stimulation unit was constructed to apply cyclic HP pressure-resistant chamber by controlling a pump and valve. A compression-loading mechanism that can apply compressive stress using an electromagnetic force was implemented in the chamber. The synchronization between the compression and HP units were evaluated and the stimulation parameters were quantitatively evaluated. Physiological HP and compressive strain were applied to the chondrocytes encapsulated in alginate and gelatin gels after applying high HP at 25 MPa, which induced damage to chondrocytes. It was found that compressive stimulation increased the expression of genes related to osteoarthritis. Furthermore, the simultaneous application of compressive strain and HP, which is similar to the physiological environment in cartilage, had an inhibitory effect on the expression of genes related to osteoarthritis. HP alone also suppressed the expression of osteoarthritis-related genes. Therefore, the simultaneous hydrostatic and compressive stress-loading device developed to simulate the mechanical environment in vivo may be an important tool for elucidating the mechanisms of disease onset and homeostasis in the cartilage.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

Silica aerogels and their derivatives have outstanding thermal properties with exceptional values in the thermal insulation industry. However, the brittle nature restricts its large-scale commercialization. Thus, enhancing their mechanical strength without affecting their thermal insulating properties is essential. Therefore, for the first time, highly thermally stable Poly(acrylamide-Co-acrylic acid) partial sodium salt is used as a reinforcing polymer to synthesize hybrid P(AAm-CO-AAc)-silica aerogels via epoxy ring-opening polymerization in the present study. Functional groups in P(AAm-CO-AAc) partial sodium salts, such as CONH2 and COOH, acted as nucleophiles for the epoxy ring-opening reaction with (3-glycidyloxypropyl)trimethoxysilane, which resulted in a seven-fold enhancement in mechanical strength compared to that of a pristine silica aerogel while maintaining the thermal conductivity at less than 30.6 mW/mK and porosity of more than 93.68%. Moreover, the hybrid P(AAm-CO-AAc)-silica aerogel demonstrated improved thermal stability up to 343 ⁰C owing to the synergetic effect between P(AAm-CO-AAc) and the silica aerogel, corresponding to thermal stability and strong covalent bonding among them. These excellent results illustrate that this new synthetic approach for producing hybrid P(AAm-CO-AAc)-silica aerogels is useful for enhancing the mechanical strength of a pristine silica aerogel without impairing its thermal insulating property and shows potential as an industrial heat insulation material.

Abstract: This study aims to analyze the physico-mechanical properties and dynamic models of tissue-simulating hydrogels, specifically the photoacoustic (PA) response signals, by varying the concentrations of polyvinyl alcohol (PVA) and molecular weight (MW). A state space model (SSM) is proposed to study the PVA hydrogels to retrieve the PA-related signal's damping ratio and nat-ural frequency. Nine box-shaped PVA hydrogels containing saline solution were used, with five concentrations of PVA (7, 9, 12, 15, 20%) for MW1 and four for MW2. The results indicated that the concentration of PVA and MW played an important role in the PA wave's amplitude, arrival time, and speed of sound over the hydrogels. The SSM parameters showed that increasing PVA and MW concentrations improved the hydrogels' ability to absorb and transfer energy under the PA effect. These parameters were also found to be correlated with density and modulus of elasticity. Addi-tionally, the concentrations of PVA and MW affected the absorption and optical scattering coeffi-cients. The physical-mechanical properties, including porosity, density, and modulus of elasticity, improved as the concentration of PVA and MW increased. The ultimate goal of this study is to develop hydrogels as phantoms that can be used for tissue simulation and imaging.

The aim of the present study was to describe and determine changes in the superelastic properties of NiTi archwires after clinical use and sterilization. Ten archwires from five different manufacturers (GAC, 3M, ODS, GC, FOR) were cut in two segments and evaluated using a three-point bending test in accordance with ISO 14841:2006. The centre of each segment was deflected to 3.1mm and then unloaded to 0 N to obtain a load-deflection curve. Deflection at the end of the plateau and forces at 3, 2, 1 and 0.5mm on the unloading curve were recorded. Plateau slopes were calculated at 2, 1 and 0.5mm of deflection. Data obtained were statistically analysed to determine differences (p<0.001). Results showed that the degree of superelasticity and exerted forces differed significantly among brand groups. After three months of clinical use, FOR released a greater force for a longer activation period. GC, EURO and FOR archwires seemed to lose their mechanical properties. GC wires released more force than other brand wires after clinical use. Regarding superelasticity after sterilization, GAC, 3M and FOR wires recovered their properties, while EURO archwires lost more.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

The global production of macadamia nuts has witnessed a significant increase, resulting in the accumulation of large quantities of discarded nutshells. These nutshells possess remarkable hardness and toughness, comparable to aluminum. Incorporating natural fillers to enhance the properties of composite materials for various applications, including light duty, structural, and semi-structural purposes, is a common practice. Given their inherent hardness and toughness, macadamia nutshells present an intriguing choice as fillers, provided that the manufacturing conditions are economically viable. With the urgent need to shift towards natural fillers and reduce reliance on synthetics, exploring macadamia nutshells as components of natural fiber composites becomes imperative. This review aims to comprehensively examine the existing body of knowledge on macadamia nutshells and their bio-synthetic polymer composites, highlighting key research findings, achievements, and identifying knowledge gaps. Furthermore, the article will outline prospective areas of focus for future research endeavors in this domain, aligning with the universal goal of minimizing synthetic materials.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

The study of mechanical properties of rock mass can be effectively carried out through rock-like material model test. The similarity of mechanical properties between rock-like material and protolith is dependent on the appropriate selection of composition and content of rock-like materials. In this research, X-Ray diffraction test was conducted to analyze the composition of deep rock, which confirmed silica, quartz, and dolomite as the primary components of deep sandstone. An orthogonal design test was used to execute the ratio test of rock-like material. River sand was used as an aggregate, cement as a binder, gypsum powder as a regulator, and polystyrene foam (EPS) as rock damage simulation material. The influencing factors considered in the orthogonal mechanical tests were the proportion of aggregate and binder, ratio of binder and regulator, quantity of damage simulation material, and size of damage simulation material. Three levels were set for each factor, and mechanical parameters such as compressive strength, tensile strength, elastic modulus, axial strain, and Poisson's ratio were tested for each group of samples. The changes of those parameters with the levels of the above four factors were studied. The study revealed that adjusting the size of polystyrene foam (EPS) can adjust the values of elastic modulus, tensile strength, and Poisson's ratio of rock-like material. Similarly, changing the ratio of binder and regulator can adjust the values of axial strain and compressive strength of rock-like material. The rock-like material developed in the study can simulate the mechanical properties of different rock masses such as granite, sandstone, shale, and limestone.

The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

The main purpose of the work was to determine the powder composition and properties of iron-based sinters used as a matrix in metallic diamond tools. The FeCuSnNi sinters obtained from a mixture of commercial powders were used for research. The material was subjected to milling in a ball mill and sinter have been performed with the hot-pressing technique in a graphite mold. The physical and mechanical properties of the sinters were tested. The investigations of obtained sinters concerned density, porosity, hardness, oxygen content, static tensile test and analysis of microstructure. The static tensile test was carried out with the use of a universal testing machine UTS-100. The study of the microstructure of sinters was performed using the JSM-7100F scanning electron microscope. The sinters are characterized by a high coefficient of thermal expansion and good mechanical properties. The FeCuSnNi sinter revealed a complex phase structure. Spot chemical analysis revealed the presence of Fe solution, Cu solution and the presence of iron oxides oxides. Nickel atoms were present throughout the sinter volume. The obtained results indicate that the presented material can be used as a matrix of a diamond-metal composite in diamond tools for the processing of natural stones and building materials.

This study investigates the influence of the porous structure, on the density and the mechanical behaviour of new foam concretes incorporating hemp shives. A total of eight batches of foam concretes were manufactured and tested, made with a protein-based foam agent, containing cement, ground granulated blast furnace slag and Metakaolin as binder and hemp shives as natural aggregate. The effect of several parameters is studied, elaboration method (direct and preformed), amount of pozzolanic additions (0% and 30%) and incorporation of hemp shives (5 and 15 vol%) on the resulting physical properties, microstructure, porous structure and mechanical behaviour of the concretes. Hemp shives incorporation results in increased concrete porosity and air bubble radius, decreased uniformity and mechanical strength, and lower cohesion with the cement matrix compared to standard concretes.

This paper begins with an introduction to porcelain tiles. A review of the major scientific and technological features of the mullite−based porcelain tile (MPT) and anorthite−based porcelain tile (APT), focusing primarily on the raw material, processing, phase evolution and mechanical behavior, is then presented. Based on the porcelain tile firing behavior and a series of physical and chemical changes that can occur, a comprehensive comparison is described. In the last part, the prospects for further developments related to MPT and APT are discussed.

Electrically conductive adhesives (ECA’s) are used widely to replace or reinforce lead soldering or conductive metal components in electronic packaging applications such as die attachment, solderless interconnections, component repair, display interconnections, and heat dissipation. Their conductive behavior as well as the associated behaviors such as heat conduction and mechanical behavior (strength, rigidity, deformation and viscoelastic behavior, which may be affected by moisture ingression) are affected by adhesive film thickness, volume fraction, size and shape of the conductive filler, as well as uncured base adhesive viscosity, substrate and filler surface treatment and the applied pressure (during bonding and during conduction). The adhesive resistivity decreases precipitously above a characteristic filler volume fraction called the percolation threshold. In general, micron-sized metal fillers mixed in an adhesive (often an epoxy) resulting with different film thicknesses exhibit thickness thresholds for transition from three-dimensional conductivity to two-dimensional conductivity with considerable increases in thickness-direction (z-axis) resistivity when the film thicknesses are smaller than these threshold values. Recently, the use of conductive nanoparticles allowed decreases in percolation threshold levels as well as increases in mechanical strength and durability of ECA’s. Most ECA’s are supplied in liquid or paste form in varying viscosities and therefore, the method of their application also affects their performance. This work intends to provide an understanding of these effects on conduction behavior in (usually high-priced) equipment in which they are used.

Polyethylene terephthalate (PET) is nowadays one of the most used polymers for packaging applications. Modifications induced by service conditions and the optimal mean to recycle this matter several times have to be perfectly understood to allow a reuse for similar application (from bottle to bottle for example). The present study aims to compare physico-chemical properties, crystalline organization, and mechanical behaviour of virgin (vPET) and recycled PET (rPET). Using different combined experimental methods (Calorimetry, Small Angle X-ray Scattering, Atomic Force Microscopy, DMA, and uni-axial tensile test), it has been proven that even if there is no change in the crystallinity of PET, the crystallisation process shows some differences (size and number of spherulites). The potential impact of these differences on local mechanical characterization, at the lamella scale, is explored and tends to demonstrate the development of homogeneous microstructure, leading to well-controlled and relevant local mechanical properties. This approach increases the understanding of crystallisation of PET and recycled PET during forming processes such as thermoforming or injection stretch blow moulding (ISBM) where elongation at break can depend on the microstructure conditioned by the crystallisation process.

There is rapidly emerging evidence from pre-clinical studies, patient samples and patient subpopulations that certain chemotherapeutics inadvertently produce prometastatic effects. Prior to this, we showed that doxorubicin and daunorubicin, stiffen cells before causing cell death, predisposing the cells to clogging and extravasation, the latter being a step in metastasis. Here, we investigate which other anti-cancer drugs might have similar prometastatic effects by altering the biophysical properties of cells. We treat myelogenous (K562) leukemic cancer cells with the drugs nocodazole and hydroxyurea, and then measure their mechanical properties using the microfluidic microcirculation mimetic (MMM) device, which mimics aspects of blood circulation and enables the measurement of cell mechanical properties via transit times through the device. We also quantify the morphological properties of cells to explore biophysical mechanisms underlying the MMM results. Results from MMM measurements show that nocodazole- and hydroxyurea-treated K562 cells exhibit significantly altered transit times. Nocodazole caused significant (p < 0.01) increase in transit times, implying a stiffening of cells. This work shows the feasibility of using the MMM to explore possible biophysical mechanisms that might contribute to chemotherapy-induced metastasis. Our work also suggests cell mechanics as a therapeutic target for much needed antimetastatic strategies in general.

Abstract: To compare the use of variable mechanical ventilation with conventional mechanical ventilation in porcine model of ARDS. Methods: Animals were divided into two groups (n = 6), conventional ventilation and variable ventilation with bi-oscillatory PEEP. For induction of ARDS, intravenous oleic acid was used until a P/F ratio of 200 to 300 mmHg. The animals were ventilated with pressure control, FiO2 1.0, inspiration-expiration ratio = 1:2, tidal volume 6 ml/kg with the initial respiratory rate adjusted to maintain an end tidal CO2 tension of 35 to 45 mmHg. Variable ventilation was characterized by the oscillation of PEEP from 5 to 10 cmH2O every 4 respiratory cycles, in convencional ventilation group PEEP was set from 5 cmH2O. Ventilatory, hemodynamic parameters, oxidative stress, antioxidant enzymes, Interleukin 8 (IL8) and 17-a (IL17a) and histological analyzes were evaluated; Results: The use of BiPEEP demonstrated improvement in lung compliance and PaO2 in relation to control. The levels of oxidative stress and antioxidant enzymes showed no significant difference. There was no difference in IL17a between groups. In IL8 there was a significant increase in the lung base of control in relation to BiPEEP, and a reduction in the apex of BiPEEP in relation to control. The control group showed changes in lung morphology characterized by cellular infiltrates, a thickening of the alveolar septae and atelectasis, which were attenuated in BiPEEP group; (4) Conclusions: The use of variable ventilation with bi-oscillatory level of PEEP demonstrates a potential ventilatory strategy in an experimental model of ARDS.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

In this work, a simple and environmentally friendly process combining low pressure (vacuum) and mechanical compression is proposed to convert recycled polypropylene (PP) foams (28 kg/m3) into low density foams (90-131 kg/m3) having negative tensile and compressive Poisson's ratios (NPR). The effect of processing conditions (vacuum time, temperature, and mechanical pressure) was studied. Based on the optimized conditions, the tensile Poisson’s ratio of the resulting auxetic foams reached −1.50, while the minimum compressive Poisson's ratios was −0.32 for the same sample. The foam structure was characterized via morphological analysis (SEM) to determine any changes related to the treatment applied. Finally, tensile and compressive properties (Young's modulus, strain energy, energy dissipation and damping capacity) are also presented and discussed. It was observed that the mechanical properties of the resulting auxetic foams were improved compared to the original PP foam (PP-O) for all tensile properties in terms of modulus (19.9 to 59.8 kPa), strength (0.298 to 1.43 kPa) elongation at break (28 to 77%), energy dissipation (14.4 to 56.3 mJ/cm3) and damping capacity (12 to 19%). Nevertheless, improvements were also observed under compression in terms of energy dissipation (1.6 to 3.6 mJ/cm3) and damping capacity (13 to 19%). These auxetic foams can find applications in sport and military protective equipment, as well as any energy mitigation system.

Not in the history of transmissible illnesses has there been an infection as strongly associated with acute cerebrovascular disease as the novel human coronavirus, SARS-CoV-2. While the risk of stroke has known associations with other viral infections, such as influenza and human immunodeficiency virus, the risk of ischemic and hemorrhagic stroke related to SARS-CoV-2 is unprecedented. Furthermore, the coronavirus disease 2019 (COVID-19) pandemic has so profoundly impacted psychosocial behaviors and modern medical care that we have witnessed shifts in epidemiology and have adapted our treatment practices to reduce transmission, address delayed diagnoses, and mitigate gaps in health care. In this narrative review, we summarize the history and impact of the COVID-19 pandemic on cerebrovascular disease, and lessons learned regarding the management of patients as we endure this period of human history.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

The objective of this research is to conduct a comparative analysis between rectangular-shaped ASTM D3039 specimens with different angles (0°, 15°, and 90°) and various tensile test specimens based on ASTM and ISO standards, all 3D-printed using polyethylene terephthalate glycol (PETG) material through FDM. The study aimed to assesses the weak spot commonly found at the neck of the specimens. Two different printing orientations, namely flat and on-edge, were investigated, and a comprehensive examination and comparison were made regarding the variations in tensile strength, E-modulus, strain, and elongation at break among the tested samples. Additionally, the broken areas was evaluated, and a numerical study utilizing the finite element method (FEM) was conducted to identify stress risers' locations in each specimen type. The experimental results demonstrated that the ASTM D3039-0° specimen exhibited the best tensile properties when printed in the on-edge orientation, while the flat orientation yielded the best results in terms of the broken area. On the other hand, the ISO 527-2 specimens displayed the lowest tensile properties, regardless of the printing orientation. The study highlighted the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location.

In this study, an extensive data set was based on existing literature records in order to enable the suitability of several predictive models, from Multiple Linear Regression (MLR) to Neural Networks (NN). The main objective was to, through regression analyses, generate model computations to correlate tensile properties (UTS- Ultimate Tensile Strength, YTS – Yield Tensile Strength and EF – Elongation-to-Fracture) to a given alloy composition and microstructural spacing. This investigation led to positive results, as the highest accuracies of the trained modules (in 80% of the database) were found to be above ~82% (UTS and EF) and a maximum of ~98% (YTS), when analyzing the results to a test data set. Later, these models were used to define trends for possible next solder alloy commercial compositions. Overall, using the standard model’s setup, the Random Forest and Decision Tree models showed the highest accuracy results, with 0.958 for YTS as opposed to 0.907 for MLR. Moreover, Multilayer Perceptron (MLP)-optimized models yielded the best results for each variable, with the highest increases in accuracy associated with the YTS and EF. The present contribution might imply an important milestone towards alloy design research based on data science guidelines to unlock the full potential of former experiments and their extensive set of results.

Advanced coatings are essential to modern technologies, as they optimise surface characteristics for different application scenarios. Transparent and self-cleaning coatings are increasingly used as protective coatings for various applications, such as foldable touchscreens, windows, and solar panels. Moreover, incorporating other functionalities such as high hardness, wear resistance, and flexibility into transparent and self-cleaning coatings is important for broadening the use cases. Although many kinds of multifunctional coatings have been developed, it is still difficult to embody several properties in one coating adequately, as some properties, such as hardness and flexibility, are inherently contrastive. This review first describes basic principles, including wetting ability, photocatalytic reactions, photo-induced hydrophilic phenomena, and the implication of self-cleaning. The desired properties of multifunctional coatings are then listed, and methods for evaluating different properties are used. Recent progress in various preparation methods for multifunctional coatings, including the sol-gel, dip/spin, and chemical vapour deposition (CVD) methods, are also presented. Magnetron sputtering (MS) technology is widely used in coating preparation. Compared with chemosynthesis and CVD, MS is time-saving, suitable for industrial production, and environmentally friendly. Coatings prepared by MS usually possess excellent mechanical properties. Thus, we highlight the current research status of MS technology in multifunctional coating preparation. Moreover, according to the multilayer design structure of coatings, their optical and mechanical properties and self-cleaning ability can be controlled by combining the characteristics of different materials. Finally, combining photocatalytic materials such as TiO2 with other materials through a multilayer structure to obtain a multifunctional coating with excellent overall properties is discussed.

There is an international concern for reducing energy consumption and protecting the environment in the construction industry. The energy efficiency of a building depends on the thermal resistance of concrete, and utilizing concrete products with elevated thermal resistance can enhance this aspect. This study analyzes the impact of perlite, as an addition, on the physico-mechanical properties of concrete, with the aim of identifying perlite concrete products that will respond to the improvement of the heat transfer resistance of the building envelope. The study examines the effect of replacing different amounts of concrete aggregates with perlite in percentages of 10%, 20%, 30%, and 100%. The results show that substituting sand with perlite improves the thermal performance of concrete, but its mechanical properties are negatively affected. The research carried out highlighted that perlite can be successfully introduced in the production of concrete blocks used for external non-bearing wall panels, the outstanding feature being the reduction of energy consumption in buildings. Overall, the paper identifies an efficient and environmentally friendly way of using perlite in the construction industry, enhancing the energy efficiency of buildings while minimizing the environmental footprint caused by the construction industry.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The evolution of transportation has been inextricably tied to the progress of civilization. Through innovation, the automobile business has been working to improve safety, quality, and compliance with environmental regulations. Electric vehicles have made significant strides in this area, but optimizing their efficiency requires a special focus because they expend energy that can be recovered in a variety of ways. Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, has recently received a lot of attention as it constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses. This study tenders a thorough examination into energy recovery technologies which could be applied to the various types of energy dissipated in electric vehicles. Firstly, the paper investigates the possible sources of energy recoverable from an electric vehicle, as well as the various types of energy dissipated. Secondly, the article examines the energy recovery technologies most frequently used in vehicles, categorizing them according to the type of energy and application. Finally, it determines that with further research and development, energy harvesting holds considerable potential for improving the energy efficiency of electric vehicles. New and innovative methods for capturing and utilizing wasted energy in electric vehicles can be established. The potential benefits of applying energy recovery systems in electric vehicles is a vital issue for the automobile industry to focus on due to the potential benefits involved. The ongoing progress currently being made in this field is expected to play a significant role in shaping the future of transportation.

Hydrogel-based wearable electrochemical biosensors (HWEBs) are emerging biomedical devices that have recently received immense interest. The exceptional properties of HWEBs include excellent biocompatibility with hydrophilic nature, high porosity, tailorable permeability, the capability of reliable and accurate detection of disease biomarkers, suitable device-human interface, facile adjustability, and stimuli-responsive to the nanofiller materials. Although the biomimetic three-dimensional hydrogels can immobilize bioreceptors, such as enzymes and aptamers, without any loss in their activities. However, most HWEBs suffer from low mechanical strength and electrical conductivity. Many studies have been performed on emerging electroactive nanofillers, including biomacromolecules, carbon-based materials, and inorganic and organic nanomaterials, to tackle these issues. Non-conductive hydrogels and even conductive hydrogels may be modified by nanofillers as well as redox species. All these modifications have led to the design and development of efficient nanocomposites as electrochemical biosensors. In this review, both conductive-based and non-conductive-based hydrogels derived from natural and synthetic polymers are systematically reviewed. The main synthesis methods and characterization techniques are addressed. The mechanical properties and electrochemical behavior of HWEBs are discussed in detail. Finally, the prospects and potential applications of HWEBs in biosensing, healthcare monitoring, and clinical diagnostics are highlighted.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

Improper lifting measures of long-span spatial steel structures during construction process may delay the construction period and even cause safety accidents. Few studies on long-span spatial steel structures considered time-varying mechanical characteristic during construction process. In order to achieve safe and efficient installation in a long-span spatial steel structure, this research presents a time-varying mechanical analysis of the synchronous and asynchronous integral lifting and a single and interlaced point’s asynchronous integral lifting analysis method of a long-span spatial steel structure. The results showed that in the case of asynchronous lifting of single point, the displacement influence on other members is related to the distance. The closer the distance from the lifting point, the greater the influence. In asynchronous integral lifting, the lifting point with large lifting force is first installed to the specified position, and the lifting point with small lifting force is installed to the specified position.

Ground-based high-power lasers enable to, in principle, deorbit any kind of space debris object from the low Earth orbit (LEO) by remotely inducing laser-ablative momentum. However, the assessment of efficiency and operational safety depends on many factors like atmospheric constraints or the risk of debris disintegration during irradiation. We analyze laser momentum for a great variety of target geometries and sizes, and – for the first time in a large-scale simulation – include thermal constraints for laser irradiation configuration. Using a coherently coupled 100 kJ laser system at 1030 nm wavelength, 5 ns pulse duration in an optimized pointing elevation angle range, the pulse frequency should amount to less than 10 Hz to prevent fragment meltdown. For mechanically intact payloads or rocket bodies, repetition rates should be even lower. Small debris fragments sized between 10 and 40 cm can be de-orbited by around 100 to 400 station passes with head-on irradiation while objects exceeding 2 m typically require far more than 1000 irradiations for deorbit. Hence, laser-based debris removal cannot be considered a prime space sustainability measure tackling the top-risk large debris, yet it can provide for remediation of a multitude of small-sized debris using small networks of globally distributed laser sites.

While traditional AC mechanical circuit breakers have been competent for protecting AC circuits, high penetration of DC power distribution technologies like DC microgrids (MGs) obligate better disruption performance features such as quick and reliable switch-ing speeds. However, a DC circuit breaker (DCCB) novel design is challenging due to the need to quickly break high currents within milliseconds, caused by the high fault current rise in DC grids compared to AC grids. In DC grids, the circuit breaker must provide zero current crossing and be designed for absorbing surges since the arc is not naturally extinguished by the system. Additionally, the DC breaker must mitigate the magnetic energy stored in the system inductance and withstand residual over-voltages after current interruption. These challenges require a fundamentally different topology for DCCBs, which are typically made using solid-state semiconductor technology, metal oxide varistors (MOV), and ultra-fast switches. This study aims to provide a comprehensive review on development, design, and performance description of DCCBs in parallel with a specific concentration on analysis of internal topology, energy absorption path and sub-circuits in Solid-State (SS)-based DCCBs. The research explores various novel designs that introduce different structures for energy dissipation solution. The classification of these designs is based on the fundamental principles of surge mitigation and a detailed analysis of the techniques employed in DCCBs. In addition, our framework offers an advantageous reference point for the future evolution of SS-circuit breakers in numerous developing power delivery systems.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

Radical prostatectomy (RP) is one of the recommended treatments to achieve oncological outcomes in localized prostate cancer. However, radical prostatectomy is a major abdominopelvic surgery. Venous thromboembolism (VTE) is a well-known complication associated with surgical procedures including RP. There is a lack of consensus regarding VTE prophylaxis in urological procedures. The aim of this systematic review was to investigate different aspects of VTE in post-Radical Prostatectomy patients. A comprehensive literature search was performed, and relevant data were extracted. The primary aim was to perform a systematic review and meta-analysis (wherever possible) of VTE occurrence in post-RP patients in relation to surgical approach, pelvic lymph node dissection, and type of prophylaxis (mechanical or combined prophylaxis). The secondary aim was to investigate- the incidence and other risk factors of VTE in post-RP patients. A total of 16 studies were included for quantitative analysis. Statistical methods for analysis included the DerSimonian-Laird random effects. We were able to conclude that the overall incidence of VTE in post-radical prostatectomy is 1% and minimally invasive procedures (MIS), including laparoscopic as well as robotic procedures for radical prostatectomy and RP without pelvic lymph node dissection (PLND) are associated with less risk of developing VTE. Additional pharmacological prophylaxis to mechanical methods may not be necessary in all cases and should be considered in high-risk patients only.

Bobbin Tool Friction Stir Welding (BTFSW) is a variant of FSW process using the special two shoulder tool that forms the top and bottom weld surface. As such, a significant simplification of welding setup is achieved. One of the dominant parameters of BTFSW process is the interference between tool shoulder pinch gap and weld metal thickness. In this research, the influence of interference of the square pin tool with convex shoulders on process temperature, microstructure, tensile, impact and bend performance were studied, and appropriate correlations were devised. The base metal was aluminum-magnesium alloy, with the interference varied in the range of 0.1 to 0.5 mm. The worm defects and irregularities were found in all specimens except in specimen welded with 0.4 mm interference. Optimal interference of 0.4 mm resulted in the highest mechanical properties, which, in terms of tensile strength and reduction of area were similar to the base metal. Furthermore, impact strength was significantly higher, which was attributed to grain refinement effect in the nugget zone.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

Root crops grow in the soil deeply and bond with soil closely, which results in that the process of the separation between soil and root becomes the most difficult during the harvesting processes. In order to harvest root crops efficiently, the mechanical harvesting has become the main developing trend. However, high power and high damage rate are still occurred when mechanical harvester gets in touch with the roots. In this paper, we review the research of the development and evaluation of the mechanical harvesting of root crops and its performance optimization on the past years. The process of soil separation mainly consists in the initial separation between root and the ground and further separation between root and adhered soil. In general, the soil-cutting operation in the initial separation and the sieving mechanism in the further separation require high draught and power. And the dramatic friction, impact, pressure and so on, which happen in the components and soil-roots, are the key reasons to lead to root damage. The optimization of harvesting methods and parameters, including the digging shovel shape, working conditions, vibration, and screening way, is more significant in improving the harvesting performance. But there are still some limitations in the research and application of the mechanical harvester for root crops. Future research is suggested to focus on the development of the soil break-up when the digging shovel cutting soil, the insight into the interaction between soil and roots by different external compression loads, and the long-term studies to verify the high-efficiency and low-damage performances of mechanical harvester in practical application.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

In recent years, additive manufacturing of products made from 5000 series alloys has grown in popularity for marine and automotive applications. In this work, we compare of mechanical properties characteristics of aluminum alloy 5056 material produced by wire-arc additive technology and rolling. We carried out tension tests under quasi-static loading and impact toughness tests under impact loading. The results show that upon similar ultimate tensile strength and ductility, material after additive manufacturing demonstrates decreased resistance against dynamic loading than material manufactured by the typical method of casting and rolling. This decrease in properties was explained through macro- and microstructure analysis.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Bronchopulmonary dysplasia (BPD), also known as chronic lung disease, is the most common respiratory morbidity in preterm infants. "Old" or "Classic" BPD, as per the original description, is less common now. "New BPD," which presents with distinct clinical and pathological features, is more frequently observed in the current era of advanced neonatal care, where extremely premature infants are surviving due to medical advancements. The pathogenesis of BPD is complex and multifactorial and involves both genetic and environmental factors. This review provides an overview of the pathology of BPD and discusses the influence of several prenatal and postnatal factors on its pathogenesis, such as maternal factors, genetic susceptibility, ventilator-associated lung injury, oxygen toxicity, sepsis, patent ductus arteriosus (PDA), and nutritional deficiencies. This in-depth review draws on existing literature to explore these factors and their potential contribution to the development of BPD.

Background: For the treatment of bone defects, biodegradable compressive biomaterials are needed as a substitute, which degrade at the same rate as the bone regenerates. In this study, the compressive strength of CPC ceramics (with a layer thickness of more than 12 layers) should be compared with sintered ceramics. Methods: Round scaffolds with 20, 25, 30 and 45 layers were 3D printed the 3D Bioplotter, solidified in a water-saturated atmosphere for 3 days and then tested for compressive strength together with a sintered ceramic using a Zwick universal testing machine. Results: The 3D printed scaffolds are more compressive at 41.56 ± 7.12 MPa than the sintered ceramic at 24.16 ± 4.44. Conclusions: The round geometry sintered ceramics approach or exceed the upper limit of the compressive strength of cancellous bone in the direction of compacta (depending on the author).

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.