Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p < 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

Teaching, learning, research, and development are all supported in a favorable atmosphere at the University of Lagos (UNILAG). The wetland systems made up of freshwater that are extremely biodiverse makeup about 10% of the total land area. Flooding, deforestation, excessive sedimentation, blockages to streams, abuse, overuse, and invasion of wetlands are some of the recent environmental challenges that the university faced. Urban heat island impacts, contaminants in the air, wetland degradation, social issues including stress, and a detachment from nature are all major concerns. With the green corridor behind the faculties of law and management science serving as a model supported by sustainability as a true foundation for UNILAG's campus landscapes, this article investigates the sustainable restoration of wetlands within the boundaries of the university. The use of qualitative techniques was employed, utilizing the Strengths-Weaknesses-Opportunities-Threats (SWOT) analysis. Additionally, a geospatial mapping of the wetlands and tributaries that connect the Lagos Lagoon was conducted to evaluate the intrinsic ecological goods and services through a series of analytical steps, beginning with an analysis of the land area, current biodiversity, hydrology, and its potential through landscape mapping and analysis. The biophysical setup, landscape features, climatic data analysis, the ecological goods and services derived from the wetlands, and the records of flooding and rainfall are all included in the geospatial evaluation and analysis. The educational institution's site planning for the remediation of its wetlands takes into account the actual evolution of the area's drainage network. Throughout the wetlands, low carbon emissions are generated by off-road bike lanes, trails for walking, and raised hardwood platforms. Combining native plant species and park furniture, the academic landscape atmosphere will be improved in each of the wetlands and aesthetic values. the country's "University of First Choice" and its biophysically restored wetlands will help illuminate the landscape while the green corridors have an innate ability to attract human affinity within the academic community. All of these elements are implemented following an environmentally friendly landscape planning, management, design model, and enforcement process.

Primary open-angle glaucoma (POAG) is a progressive optic neuropathy with a complex, multifactorial aetiology. Raised intraocular pressure (IOP) is the most important clinically modifiable risk factor for POAG. All current pharmacological agents target aqueous hu-mour dynamics to lower IOP. Newer therapeutic agents are required as some patients with POAG show a limited therapeutic response or develop ocular and systemic side ef-fects to topical medication. Elevated IOP in POAG results from cellular and molecular changes in the trabecular meshwork driven by increased levels of transforming growth factor β (TGFβ) in the anterior segment of the eye. Understanding how TGF affects both the structural and functional changes in the outflow pathway and IOP is required to de-velop new glaucoma therapies that target the molecular pathology in the trabecular meshwork. In this study we evaluated the effects of TGF-1 and -2 treatment on miRNA expression in cultured human primary trabecular meshwork cells. Our findings are pre-sented in terms of specific miRNAs (miRNA-centric), but given miRNAs work in net-works to control cellular pathways and processes, a pathway-centric view of miRNA ac-tion is also reported. Evaluating TGF-responsive miRNA expression in trabecular meshwork cells will further our understanding of the important pathways and changes involved in the pathogenesis of glaucoma and could lead to the development of miRNAs as new therapeutic modalities in glaucoma.

Purpose: To examine the effectiveness of patterned laser trabeculoplasty (PSLT) as an additional treatment for patients of open-angle glaucoma (OAG) receiving maximized ocular hypotensive medications (OHM). Methods: Forty eyes of 33 patients (average age 72.7±10.7 years) who had not previously undergone open glaucoma surgery or laser trabeculoplasty and were treated with maximized OHM between June 2018 and March 2022 were included. A 360-degree PSLT was conducted and postoperative intraocular pressure (IOP) and survival curves at 1, 3, 6, 9, and 12 months were evaluated. Results: According to the Kaplan-Meier survival analysis, the average survival time was 8.1 months with death defined as postoperative IOP reduction of less than 10% or requiring additional treatment. The average survival time was 4.9 months with death defined as postoperative IOP reduction of less than 20% or requiring additional treatment. In the 31 eyes which received no additional treatment after PSLT, the mean preoperative IOP was 18.5±3.9 mmHg, which reduced to 15.3±4.1 mmHg (p=1.62 x 10-6)), 15.5±3.4 mmHg (p=1.51 x 10-5), 15.7±4.0 mmHg (p=1.75 x 10-5), 14.7±4.38 (p=2.89 x 10-6), and 15.0±4.0 mmHg (p=5.74 x 10-9) at 1, 3, 6, 9 and 12 months after PSLT, respectively. The IOP reduction rate one year after PSLT was 18.7%. Thirteen of the 31 eyes (42%) achieved a 20% reduction in IOP compared to the baseline. Conclusion: Adjunctive treatment with PSLT in OAG patients receiving maximized OHM may be effective over 12-months of follow-up.

INTRODUCTION: Breast sensibility following reconstruction surgery, though often overlooked, holds significant importance due to its widespread occurrence and profound effects on patients’ well-being and safety. Our objective is to compare the sensory outcomes between DIEP flap microsurgery reconstruction and implant-based reconstruction. Additionally, we explored the potential influence of sociodemographic and clinical factors on sensory recovery, along with assessing temperature discrimination abilities and evaluating quality of life. MATERIAL AND METHODS: We conducted an ambispective descriptive-analytical study, involving women who underwent mastectomy with reconstruction using either DIEP flap and implants at our hospital between 1990 and 2021. Data were collected from medical records, patient histories, physical examination, and validated quality of life questionnaires (BREAST-Q). RESULTS: A total of 99 women with breast reconstruction were included, 47 with DIEP flap and 52 with implants. Sensory recovery in implant-based reconstruction was found to be superior to DIEP flap reconstruction (5.03 and 5.18 respectively, p-value <0.005). A direct correlation was observed between sensory improvement and thermal discrimination (Spearman coefficient 0.9, p-value <0.001). Factors such as radiotherapy, delayed reconstruction with DIEP flap, and height with implants were associated with poorer sensory recovery in the breast. Women experiencing better breast sensibility reported higher satisfaction with their surgeon, medical team, and psychosocial quality of life. CONCLUSION: Women reconstructed with implants or DIEP abdominal flap exhibit suboptimal overall sensory recovery of the reconstructed breast, with slightly better outcomes observed in women reconstructed with implants.

We report the case of a 61-year-old woman who was referred to the Oral Surgery and Implantology Unit of the University Hospitals of Geneva to take care edentulous sites after dental avulsions of teeth 11 and 21 following traumatic shock due to endotracheal intubation under general anaesthesia. The dental history revealed that the patient had a history of generalized chronic periodontitis that had been treated several years earlier. Treatment consisted, for the first time to our knowledge, of immediate insertion of implants at sites 11 and 21 with simultaneous bone augmentation in a single surgical procedure and immediate restorations.

Objectives (Purpose) This study aims to evaluate the outcomes of the Subcrestally Placed Implant (SPI) technique in single molar cases, focusing on biological stability and aesthetics. It proposes a schematic model to elucidate the interplay between the biological stability of soft tissues and bone around the SPI and the morphological requisites that Implant Abutment Prostheses (IAP) must fulfill to effectively replace natural teeth. Materials and methods I examined 20 cases using the SPI technique with Internal Platform Switching (IPS) design implants for single molar replacements to assess their stability. Routine check-ups utilized plain panoramic X-rays to measure changes in crestal bone on the mesial and distal sides. Additionally, 10 cases with CBCT X-rays taken more than one year after the initial surgery underwent a novel 3-dimensional soft tissue analysis (3DSTA). Measurements included placement depths (PD), soft tissue thickness (STT) at central (cPD, cSTT) and peripheral areas (pPD, pSTT), the length of the Transitional Zone (TZ) on mesial, distal, facial, and lingual aspects, and crestal bone thickness (CBT) at buccal and lingual sites. Results Panoramic analyses showed minimal changes in crestal bone (mean changes of pPD were less than 0.1 mm) over an average period of 3.3 years. Average measurements were as follows: cPD was 1.7 mm, pPD was 2.7 mm, cSTT was 0.2 mm, pSTT was 0.6 mm, TZ length was 3.8 mm, buccal CBT was 3.0 mm, and lingual CBT was 3.7 mm. Conclusions CBCT analyses of the topographical relationships between soft tissue and crestal bone with IAP for SPIs demonstrated stable results over an average 3-year period. The consistency in the relationship between crestal bone and surrounding soft tissue can be ascribed to biological structural integrity. The study classified peri-implant soft tissues into subcrestal and supracrestal (transitional zone – TZ) segments, exploring their characteristics through dimensional measurements and assessing mechanical resistance. Further histological study is needed to identify specific features of each segment.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p<0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p<0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Background: In most cases, intra-labyrinthine schwannoma (ILS) occurs in patients with unilateral hearing deterioration or neurofibromatosis type II (NF II). The pattern of localization of these tumors is various but affects mostly the cochlea. Extirpation of the ILS, if hidden by the cochlea modiolus, is difficult under the aspect of complete removal. Therefore, a tissue removal device (TRD) was designed and tested in temporal bones. The principle of handling the new device is a pushing and pipe cleaner handling inside the cochlea. This present study aimed to describe the first in vivo experience with the newly developed TRD for removing cochlear intra-labyrinthine schwannoma. Methods: In three patients, the TRD was used for the tumor removal of ILS. In two patients with a cochlear schwannoma in combination with a cochlea implantation and one patient suffering from NF II, a cochlear schwannoma was removed with the TRD. The access was performed with a posterior tympanotomy, an enlarged round window approach, and an additional second-turn access. The device was inserted and extracted gradually from the second turn access until the rings were visible in the second turn access. By pushing and pipe cleaner handling, the tumors were removed. An MRI control was performed on the day postoperatively with a T1 GAD sequence. Results: Tumor removal with the TRD was performed in a 15-minute procedure. MRI control confirmed a complete removal on the postoperative day in both cases. Conclusion: In vivo handling of the device confirmed a straightforward handling for tumor removal. MRI scanning showed a complete removal of the tumor by the TRD.

The ultimate goal of our review is to draw clinician’s attention, especially of those who are managing pediatric patients with permanent, long-standing, ventriculoperitoneal or, less commonly, ventriculo-atrial shunts. This specific subgroup of patients may eventually suffer from severe, intractable headaches which may negatively impair their quality of daily living. In the absence of any other clinical condition that could be attributed as the cause of the headache, shunt overdrainage should not be overlooked but, on the contrary, should be seriously taken into consideration in the therapeutic armamentarium of such cases, that are difficult to be handled.

Background: The main objective of this study is to develop a customized metatarsophalangeal implant for the treatment of various conditions affecting this specific joint. This approach involves replacing the joint with a custom implant designed specifically to fit each patient's unique anatomical structure. The need for custom implants stems from the obvious lack of size variety available, which presents a major challenge when, the search for the ideal size implant can be a hard task, also when considering the possibility of extensive modification of the bone to adapt it to the available implant. This adaptation, often synonymous with bone reduction, can cause significant post-operative pain for the patient and impact healing time. Methods: A comparative study of modeling software was carried out to select the perfect software, by defining and comparing the relevant criteria. Similarly, the different biomaterial options were examined and compared to select the one best suited to this project, mentioning the imaging modality used to determine the types of images used for our approach. Finally, the 3D printers used in this work were represented, highlighting their technical characteristics. Findings: A resin metatarsophalangeal implant prototype was created using 3D modeling and reconstruction software and tools. Interpretation: Reconstruction and 3D modeling techniques are revolutionizing implant creation, offering customized solutions for patients suffering from metatarsophalangeal joint disorders caused by a wide range of diseases. These results have significant implications for disability management and rehabilitation, encouraging further exploration and progress.

The aim of this study was to evaluate the use of a flexible synthetic polymer bone graft to provide implant stability in the absence of implant stability during implant placement in a dense cortical bone model. Sockets were prepared on polyurethane blocks according to the standard implant socket drilling protocol in the control group, both oversizing and deepening in group 2, and oversizing only in group 3. In groups 2 and 3, flexible synthetic polymer bone grafts were placed in the sockets prior to implant placement. The implants were placed at bone level in all groups. The highest torque value obtained was recorded as the insertion torque. 75 implant sites in 3 groups were included in the study. The torque values of the implants in the control group were significantly higher than those of the implants with the oversized and deepened sockets and the oversized-only sockets (p<0.05; p<0.01).The torque values of the implants with the oversized and deepened sockets were significantly higher than those of the implants with the oversized-only sockets (p<0.01). In this study, flexible synthetic polymer bone graft was shown to be effective in achieving implant stability in the management of implants with loss of primary stability.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

The study aimed to evaluate implant success and bone height variations after transcrestal sinus floor elevation (tSFE) using the osseodensification technique (OD) combined with beta-tricalcium phosphate (β-TCP), as bone graft material and simultaneous implant placement. Thirteen patients requiring the placement of one implant in the upper posterior maxilla, with a residual bone height of

In the last decades, the impacts of urbanization on the hydrological cycle have led to an increase in the frequency and magnitude of urban flooding events, also amplified by the effects of climate change. Sustainable Drainage Systems (SuDS) provide a revolutionary change in this field, improving the sustainability and resilience of cities. This research explores the integration of different SuDS with the aim of significantly reducing both flow volume and celerity of floods in a residual urban catchment area of metropolitan city of Querétaro (Mèxico), where extreme rainfall frequently occurs. This catchment is a representative suburb of urban pressure and environmental degradation problems. Currently, managing storm water under climate uncertainty through a multi-disciplinary approach is a major concern in this urban area. A 1D-2D coupling model of shallow water equations, finite volume method, unstructured meshing method, and hybrid parallel computing application defined the optimal configuration of SuDS at catchment scale to reduce the flood vulnerability in Querétaro. Specifically, in this paper we explore the management issues of the proposed SuDS configuration that acts as a water resource system with multiple purposes. A generic simulation model called MODSIM was applied to simulate the designed urban drainage system under a balanced IPCC future climate scenario in terms of reliability, resilience and vulnerability against water scarcity.

This review article explores the transformative impact of Artificial Intelligence (AI) on glaucoma care, focusing on advancements in diagnosis, monitoring, and treatment algorithms. AI technologies have revolutionized the field of ophthalmology by enhancing the accuracy and efficiency of diagnosing glaucoma. Furthermore, AI-powered monitoring systems enable continuous and personalized patient care, facilitating early detection of disease progression. Integrating AI algorithms in treatment protocols promises individualized and optimized therapeutic strategies for better management of glaucoma. This comprehensive review elucidates AI applications' current state and future directions in transforming glaucoma care, emphasizing the potential benefits of improving patient outcomes.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

Childhood glaucoma encompasses congenital and juvenile primary glaucoma, which are heterogeneous, uncommon, and irreversible optic neuropathies leading to visual impairment with poorly understood genetic basis. Our goal was to identify gene variants associated with these glaucoma types by assessing the mutational burden in 76 matrix metalloproteinase-related genes. We studied 101 childhood glaucoma patients with no identified monogenic alterations using next-generation sequencing. Gene expression was assessed through immunohistochemistry. Functional analysis of selected gene variants was conducted in cultured cells and in zebrafish. Patients presented a higher proportion of rare variants in four metalloproteinase-related genes, including CPAMD8 and ADAMTSL4, compared to controls. ADAMTSL4 protein expression was observed in the anterior segment of both the adult human and zebrafish larvae's eye, including tissues associated with glaucoma. In HEK-293T cells, expression of four ADAMTSL4 variants identified in this study showed that two variants (p.Arg774Trp and p.Arg98Trp) accumulated intracellularly, inducing endoplasmic reticulum stress. Additionally, overexpressing these ADAMTSL4 variants in zebrafish embryos confirmed partial loss-of-function effects for p.Ser719Leu and p.Arg1083His. Double heterozygous functional suppression of adamtsl4 and cpamd8 zebrafish orthologs resulted in reduced volume of both the anterior eye chamber and lens within the chamber, supporting a genetic interaction between these genes. Our findings suggest that accumulation of partial functional defects in matrix metalloproteinases-related genes may contribute to increased susceptibility to early-onset glaucoma and provide further evidence supporting the notion of a complex genetic inheritance pattern underlying the disease.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

The objective of this study was to evaluate the pain and inflammatory response in soft tissues using healing and prosthetic abutments of different diameters and lengths. Methods: The study population was rehabilitated with Astra tech EV single implants (Dentsply Sirona, Atlantis, Dentsply Sirona S.A., Barcelona, Spain), 4.2 and 4.8 millimetres in diameter in upper and lower maxilla and loaded with custom abutments digitally designed with the software of the company Dentsply Sirona (Atlantis WebOrder, Dentsply Sirona S.A., Barcelona, Spain), version 4.6.5, with a larger diameter than the healing abutment, to account for biomarkers through ELISA. Results: Rehabilitations in mandible and with healing abutments below 4.29 millimetres and rehabilitators below 2.18 millimetres elicited higher pain and inflammatory responses, and in turn higher interleukin 1β values. Conclusions: Greater inflammation was evident in cases in which healing abutments with reduced diameter were used in relation to the same subsequent rehabilitation with prosthetic abutments of larger diameter.

In this field pot study, effect of drainage method (e.g., intermittent drainage (ID) and continuous flooding (CF)) on greenhouse gas (GHGs: CO2 and CH4) emission was determined from three Korean paddies (BG, MG, and JS series), varying soil properties such as soil texture, labile carbon, and mineral types. Emission of GHGs was evidently influenced by the irrigation, to a different extent, depending on paddy’s redox (Eh) shift upon flooding events. The Eh decline upon flooding was slower in JS pot, where pore-water concentration of ferric and sulfate ions is the highest (~ up to 3-fold) among three paddies. MG pot was 2- to 3-fold percolative than others and the Eh drop during flooding period was the smallest (staying above -50 mV). In ID treatment, CH4 emission (t CO2-eq ha-1 yr-1) was reduced in a wide range by 5.6 for JS pot, 2.08 for BG pot, and 0.29 for MG pot relative to CF, whereas CO2 emissions (t CO2-eq ha-1 yr-1) was increased by 1.25 for JS pot, 1.07 for BG pot, and 0.48 for MG pot due to the enhanced oxidation of labile carbon. Grain yield and aboveground biomass production from ID were no less than those from CF (p < 0.05). Consequently, gain of global warming potential (S GWP) by ID varied as the order of JS (37%) > BG (14%) > MG (~0 %) pots, and negligible effect observed for MG pot is due to the equivalent trade-off between CO2 and CH4. Our findings suggest that the efficacy of ID practice on GHGs emission can be further improved by the consideration of redox response of paddy system.

Breast cancer is the most common cancer in women globally, often necessitating mastectomy and subsequent breast reconstruction. Silicone mammary implants (SMIs) play a pivotal role in breast reconstruction, yet their interaction with the host immune system and microbiome remains poorly understood. This study investigates the impact of SMI surface topography on host antimicrobial responses, wound proteome dynamics, and microbial colonization. Biological samples were col-lected from ten human patients undergoing breast reconstruction with SMIs. Mass spectrometry profiles were analyzed for acute and chronic wound proteomes, revealing a nuanced interplay between topography and antimicrobial respondseproteins. 16S rRNA sequencing assessed mi-crobiome dynamics, unveiling topography-specific variations in microbial composition. Surface topography alterations influenced wound proteome composition. Microbiome analysis revealed heightened diversity around rougher SMIs, emphasizing topography-dependent microbial inva-sion. In vitro experiments confirmed staphylococcal adhesion, growth, and biofilm formation on SMI surfaces, with increased texture correlating positively with bacterial colonization. This comprehensive investigation highlights the intricate interplay between SMI topography, wound proteome dynamics, and microbial transmission. The findings contribute to understanding host-microbe interactions on SMI surfaces, essential for optimizing clinical applications and minimizing complications in breast reconstruction.

A healthy 47-year-old woman consulted the Oral Surgery and Implantology Unit of the University Hospitals of Geneva with a request to treat her painful tooth 11 and replace the missing tooth 21. The dental history revealed that the patient had lost teeth 21 and 22 due to advanced caries. On clinical examination, tooth 11 showed an ill-fitting prosthetic crown with overhanging margins, an increased localized probing depth of 8 mm in the disto-vestibular area and sensitivity to percussion. The edentulous site 21 showed horizontal bone atrophy. Radiological examination revealed a well-defined unilocular radiotransparent lesion surrounded by a thin radiolucent border, located at the apex of tooth 11 and measuring 10 x 8 mm. The treatment consisted of extraction of 11, enucleation of the apical lesion, insertion of implants at sites 11 and 21 with simultaneous bone augmentation in a single surgical procedure with aesthetic and functional results at 3-year follow-up without any complications. Our case highlights that immediate implant placement in case of cystic periapical lesion represents a good valid alternative to standard treatment.

This article addresses the challenge of simulating rainstorm waterlogging in urban-scale areas where reliable drainage pipe network data is often lacking. Despite existing methods attempting to tackle this issue, there remains a gap in effectiveness. We present a novel approach, the Modified Equivalent Infiltration (MEI) method, building upon the foundation of the Equivalent Infiltration (EI) method. The study focuses on the outer ring area of Shanghai, utilizing data from the "In-Fa" typhoon period for simulation and comparison. Our findings reveal that the MEI method, requiring the same data inputs as the EI method, surpasses its predecessor in both principle and simulation results. Additionally, the MEI method demonstrates robustness in handling rainstorm waterlogging scenarios.

The majority of contemporary total hip arthroplasty (THA) implants are constructed from Ti-alloys, which are generally believed to generate fewer adverse local tissue reactions (ALTR) compared to CoCr-alloys. This study presents a case of unusual primary THA failure where a substantial release of Ti-alloy debris was observed. A 52-year-old active male underwent THA after posttraumatic aseptic necrosis of the femoral head in 2006. Seventeen years after the procedure, the patient presented with groin pain and restricted range of motion. X-rays revealed protrusion of the alumina ceramic head through the Ti6Al4V acetabular cup. Trace element analysis indicated significantly elevated levels of serum Ti, Al and V. CT and MRI confirmed Ti-alloy cup failure and severe ALTR. During revision surgery, the worn-out ceramic head was in direct contact with the acetabular cup, having protruded through the central hole it created over time. Histological analysis of tissue samples showed wear-induced synovitis with areas of multinucleated foreign-body giant cells and accumulation of numerous metal particles but no acute inflammatory response. Six months after the revision THA, the patient has experienced favourable outcomes. This case provides an instructive illustration for studying the consequences of substantial release of Ti-alloy debris from orthopaedic implants.

Peri-implantitis continues to be one of the major reasons for implant failures. We propose a new approach for incorporating MTA into Zirconia implant surfaces with Nd:YAG laser and investigate the biological response of peri-implant cells as well as the microbiological response. Discs of Zirconia stabilized with Yttria and Titanium were produced according 4 tested groups: Nd:YAG laser textured Zirconia coated with MTA (Zr MTA); Nd:YAG laser textured Zirconia (Zr Textured); Zirconia and Titanium discs (Zr and Ti ). Contact profilometry was used to evaluate surface roughness. Human osteoblasts, gingival fibroblasts and S. oralis were cultured on samples. Cell adhesion and morphology, cell viability, cell differentiation markers and bacterial growth were assessed. Zr Textured roughness was significantly higher compared to all other groups. Cellular adhesion was observed at 1 day in all samples in both cell lines. Osteoblasts viability was lower in Zr MTA group, unlike fibroblasts viability was shown to be higher in Zr MTA group compared to Zr Textured group at 3 and 7 days. Osteocalcin and IL-8 release by osteoblasts were higher in Zr MTA. Zr Textured showed higher IL-8 values released by fibroblasts. No differences in S. oralis CFUs were observed between groups. The results suggest that Zirconia implant surfaces coated with MTA seems to promote fibroblasts proliferation and osteoblasts differentiation, however does not appear to have antibacterial properties.

This study introduces a technique to uncover concealed patterns in satellite altimetry data, reflecting sea level variations in inland water bodies. We applied the methodology to the Caspian Sea, using altimetry data from four satellite missions over 27 years (1993-2020): TOPEX/Poseidon, Jason1, Jason2, and Jason3. The approach involves two steps: estimating sea level trends and identifying breakpoints that indicate trend shifts; and leveraging time lags between breakpoints at various locations to classify water drainage areas according to their degree of influence on each period. By revealing concealed patterns in the altimetry data, this technique can provide insights to understand the impacts of global warming and local climate changes on sea level fluctuations in the Caspian Sea. We hope that our study can facilitate subsequent interdisciplinary research on the intricate interplay between climate change and hydrological processes in inland water bodies.

The aim of this paper was to determine the soil phosphorus release risk from drained and re-wetted peatlands under different landcovers. The study was carried out at 10 soil profiles (organic soils, frequently with mursh in the topsoil, developed from low peat with various degrees of decomposition, on mineral subsoil or gyttja) located south-west of Lake Kośno nature reserve in northern-central Europe (north-eastern Poland). The soil samples were collected from the depths of 0-30 cm, 50-80 cm and 100-130 cm during spring, summer and autumn (in April, July, and October). In the laboratory, the following soil properties were determined: ash content, soil reaction, content of total organic carbon, total nitrogen, total and plant-available phosphorus. Gyttja formations and hemic peats had the highest total P content (6.77 g∙kg-1 and 2.29 g∙kg-1, respectively). Murshes contained twice less P (1.18 g∙kg-1). In spring, more plant-available phosphorus (AP sp) was released in murshes (0.29 g∙kg-1) than in peats (0.07-0.14 g∙kg-1). In the summer, higher amounts of plant-available P were stated in fiber peats (0.37 g∙kg-1) than in murshes (0.26 g∙kg-1), whereas in autumn, the amounts of P in murshes (0.22 g∙kg-1) and peats (0.21-0.23 g∙kg-1) did not vary. Generally, average contents of AP were the highest in murshes (0.26 g∙kg-1) and fiber peats (0.25 g∙kg-1), and the lowest in sapric peats (0.15 g∙kg-1). The release of phosphorus from organic compounds or binding of P by organic matter (immobilization) depends on the C:P ratio in plant residues and soil. If it is wide (>300), P is bound, if it is narrower (150–200), P is released. In the tested soil formations, the C:P ratio was frequently above 300. Only in some murshes and gyttjas the C:P ratio was below 150, which may indicate a risk of phosphorus release to groundwaters.

Glaucoma poses a serious public health concern as it is the second leading cause of blindness after cataracts, while also being the leading cause of irreversible blindness worldwide. Glaucoma is more prevalent among Black, Latino, and Asian populations and it is essential to examine both racial and ethnic disparities that exist in treatment and prevention. As the number of people with glaucoma continues to grow, it is important to review aspects of this condition in order to better care for those affected. This article will review significant forms of glaucoma and what differentiates them in a diagnosis, treatment options, and recommendations on prevention and improving awareness

In areas where conventional fundus cameras are logistically unaffordable, the smartphone-based approach is considered as a promising future of glaucoma screening due to their affordability and ease-of-use. Optic disc localization is a critical stage during glaucoma screenings. For fundus images captured with standard fundus cameras, the majority of the models available out there can locate the optic disc with satisfactory performance. However, for images that are captured with smartphone-based fundus cameras, the inherent noise and lower quality of the fundus image makes it difficult for models to detect the optic disc region. In this study, we have proposed to utilize YOLOv8n for optic disc localization due to the model’s cutting-edge performance in diverse tasks and its lightweight nature. We have used a public dataset which has 2000 low quality fundus images that are captured using a smartphone-based fundoscopy device. From these, 60% of the data was used for fine-tuning the model, and 25% for testing. By using a confidence of 50% set as threshold, the model was able to detect the optic disc successfully on over 97% of test images with intersection over union of above 0.85. These results highlight the potential of the lightweight YOLOv8n model for deployment on resource-constrained environments, offering a promising performance on accurately localizing the OD and enhancing the feasibility of affordable glaucoma screening on smartphones.

Although the connection of implant abutments to implant analogs and implant bodies has been evaluated separately, comparative evaluation of connections to implant analogs and implant bodies has not been evaluated. The objective of this study was to identify whether torque applied during laboratory manufacturing and during restoration cementation affects the compatibility between the implant body-abutment and the implant analog-abutment, as well as to spot any structural differences. Three different implant system with internal conical connection (Bioinfinity, Dant, and Dentist) were used. For each group, straight abutments (n=20) were tightened to implant analogs (n=10) and implant bodies (n=10) with hand tightening and using torque wrench device. The fitting of componenets were evaluated for each group using linear and volumetric micro-CT analysis. For linear analysis, when the mean differences (difference between measurements of the linear distance of abutments during hand tightening and applying torque) values between implant analog and implant body were compared within groups, There was no statistically significant difference observed in all groups (p> 0.05). Throughout the fabrication and clinical phases, it is recommended to tighten the abutments on the analogs with a torque wrench instrument to minimize the risk of prosthetic incompatibility.

Glaucoma is a group of ocular diseases that causes irreversible blindness worldwide and is characterized by a multifactorial degeneration of optic nerve and retinal ganglion cells (RGCs), leading to vision loss. One of the significant risk factors in glaucoma pathogenesis is glia-driven neuroinflammation. Impairment of mitochondrial dynamics and bioenergetics is associated with glaucomatous neurodegeneration and is linked to neuroinflammation. Apolipoprotein A-I binding protein (AIBP) binds to toll-like receptor 4 (TLR4) and facilitates the removal of excess cholesterol from the plasma membrane in activated cells, suggesting the regulation of cholesterol-driven inflammation by inhibiting the TLR4-associated lipid rafts. AIBP is localized in mitochondria and regulates mitophagy by ubiquitination of mitofusin 1 and 2. We observed elevated intraocular pressure-induced AIBP deficiency in glaucomatous neurodegeneration. We also observed that AIBP deficiency activated TLR4 in Müller glia, triggered mitochondrial dysfunction in both RGCs and Müller glia and impaired visual function. In mouse models of glaucoma, AIBP treatment protects RGCs by reducing inflammatory responses. Here, our review focuses on investigating the role of AIBP in the retina and examining the underlying mechanism by which AIBP contributes to the pathogenesis of glaucoma, aiming to provide new insight into the therapeutic potential for the treatment of glaucoma.

Implantation of two electrical stimulators of different cranial nerves in one patient is rare. We report the case of a forty-seven-year-old patient already implanted with a trigeminus nerve stimulator. In addition, this patient suffered from hearing problems. In one ear, the patient was deaf. On the other side, the patient wore a bone conduction hearing aid to improve hearing. In this complex situation, we decided to check the possibility of cochlear implantation on the deaf side. Finally, we managed to provide electrical stimulation of the auditory pathway of the deaf ear to improve the patient’s hearing tests. In addition, this case report shows how the trigeminus stimulator interferes with the electrical stimulation in auditory evoked potentials measurements of the auditory brainstem and cortex via EABR (evoked auditory brainstem response) resp. EALR (evoked auditory late response).

Among hearing aid (HA) users, there is a considerable variability in word-recognition scores (WRS). This variability is most pronounced among individuals with moderately severe to severe hearing loss. The variability cannot be adequately explained by factors such as the pure-tone audiogram, audiogram type, or age. This prospective study was designed to investigate the relationship between tone decay (TD) and WRS in a group of HA users with corresponding pure-tone hearing loss. The study population included 22 patients with hearing loss between 50 and 80 dB HL. Aided WRS, unaided WRS and TD were assessed for both ears. TD was found to be frequency-dependent. TD and WRS were correlated, with up to R=–0.66. The TD test was revealed as a feasible method for explaining the variability in WRS among HA users with hearing loss below 80 dB. This may contribute to improved differential diagnostics. The TD test may thus offer a better understanding of the limitations of HA use in the context of cochlear implant candidacy assessment for HA users.

Purpose To investigate secondary glaucoma resulting from uveitis in a patient infected with Human T-cell Leukemia Virus Type 1 (HTLV-1) pathologically and discuss the management of glaucoma with recurrent uveitis. Clinical course An octogenarian woman diagnosed as a carrier of HTLV-1 experienced recurrent uveitis and a sudden rise in intraocular pressure (IOP) in both eyes. Due to the uncontrolled IOP and severely damaged visual field in her left eye, a combined procedure of trabeculectomy and DGIS (Glaucoma drainage implant surgery, Baerveldt 350) was performed. The presence of HTLV-1 provirus was detected in the aqueous humor. Her trabeculectomy sample was processed for light microscopic observation. Following an irregular follow-up, she presented with a sudden decrease in vision and pain in her fellow eye, four years after the glaucoma surgeries. Her right eye exhibited a significant accumulation of mutton-fat-like keratic precipitates. Results Clinical manifestations revealed the presence of granulomatous uveitis. The combined glaucoma surgery, along with continuous topical corticosteroid medication post-surgery in her left eye, effectively suppressed the high IOP spikes and the recurrence of uveitis for 4 years. The pathological examination of the outflow pathways showed a range of damages in Schlemm's canal (SC), including SC endothelial loss, narrowing, and occlusion, as well as loss of trabecular meshwork (TM) cells and fused TM beams. Conclusion Combined GDIS and trabeculectomy represents a promising approach for managing such refractory cases of secondary glaucoma. The continuous topical corticosteroid medication is strongly recommended to prevent irreversible changes in SC and TM associated with granulomatous uveitis.

In implantology, among the key choices, to obtain predictable results, it’s essential to establish, using CBCT, the bone site where to insert the implants; these sites must be identified on the mucosa and secondarily, during the surgical phase, on the cortical bone. Surgical templates are a valid aid especially in complex cases which require sev-eral implants. In cases of single implant, on the other hand, surgical guides are rarely used and the implant is inserted freehand and the identification of the implant site on the oral mucosa is more difficult; for this reason the clinician uses the teeth in the arch as a ref-erence. This experimental study is based on the use of a thermo-printed mask, con-taining radiopaque references which, worn by edentulous patients during the execu-tion of the CBCT, helps to evaluate the identification of the implant sites on the patient when surgical guides are not used and the free hand technique is adopted. This method is certainly reserved for experienced operators capable of identifying the correct angle of the implants with the freehand technique. The level of experience remains fundamental in the clinician's decision whether or not to use surgical guides; in fact, doctors with little experience should use surgical guides even in the simplest cases to reduce the risk of error.

Background: Retinal vascular abnormalities may be associated with glaucomatous damage. Adaptive optics (AO) is a new technology that enables analysis of retinal vasculature at the cellular level in vivo. The purpose of this study is to evaluate retinal arteriolar parameters using the adaptive optics fundus camera (AO -FC) rtx1 in patients with primary open-angle glaucoma (POAG) at different stages and to investigate the relationship between these parameters and changes in optical coherence tomography (OCT) and perimetry. We wanted to assess whether vascular changes could be a cause or effect of glaucomatous damage. Methods: Parameters of retinal supratemporal and infratemporal arterioles (wall thickness (WT), lumen diameter (LD), total diameter (TD), wall-to-lumen ratio (WLR), and cross-sectional area of the vascular wall (WCSA)) were analysed with the rtx1 in 111 POAG eyes, divided into three groups according to the severity of disease and 70 healthy eyes in correlation of structural defects in retinal nerve fibre layer and visual fields defects. Results: Compared with the control group, the POAG groups showed significantly smaller TD and LD values (p<0,05) and significantly higher WLR and WT values (p<0,05) for supratemporal and infratemporal arterioles. Rtx1 parameters significantly correlated with OCT parameters (retinal nerve fibre layer, ganglion cell complex and rim area) and visual field parameters (mean deviation and pattern standard deviation) (p<0.05). Conclusion:  The results suggest that vascular dysfunction may be involved in POAG pathogenesis and neurodegenerative damage, even at the very early stage of glaucoma, without visual field defects.

Dental implant fracture is closely connected to the stress buildup surrounding the implant system during static loading. In areas where the cross section of the implant rapidly changes or where the geometry of the implant system has discontinuities, stress concentrations arise. Therefore, the implant's design is crucial in preventing early failure of the implant system, including fracture, screw loosening, and increased leakage, in addition to reducing stresses at the implant-abutment interface. In the current work, three-dimensional (3D) models of mechanically connected Ti6Al4V implant systems in various dimensions were constructed. Finite Element Analysis (FEA) was used to conduct a stress study of the created implants under actual acting forces static loading conditions in accordance with ISO 14801. In the created models, design elements including implant screw type, thickness, and taper angle of abutment were modified in order to increase the longevity of the implants. The results show that the equivalent stress level is dramatically reduced from 596.22 MPa to 212.72 MPa in the implant model, which exhibit more homogeneous stress pattern under static loading conditions. Furthermore, the relatively smoother stress transmission observed in this model holds promise for the development of new implants capable of withstanding the forces encountered in the oral environment.

Acid mine drainage (AMD) contamination is the primary environmental issue in industrial areas and where geological mining occurs. The oxidative dissolution of sulphide minerals causes AMD, natural ecosystems depend on microbial diversity and functioning at their best. This review presents the long-term effects of AMD water such as pollution from heavy metals (HM) on humans and plants, and the solution to the problem of heavy metal pollution by microbes metal interactions.

The advent of zirconia ceramics with excellent mechanical, biomechanical and optical properties has made it an attractive metal-free substitute for titanium implants. Both animal and human studies have documented shortcomings with titanium implants. A review of the current literature on 3 iterations of zirconia implant designs has been challenging due to heterogeneous success data and limited follow-up. Zirconia implants hold promise for a new generation of dental implants, but technical developments are needed for design and material enhancements that will need to be validated by long-term rigorous studies.

Purpose: The objective of the study was to qualitatively assess micro-gap dimensions, connecting fitting surface profile and bacterial leakage of machined and cast high gold alloy UCLA abutments, with or without electrodeposited gold coatings attached to external hexagon implants. Materials and methods: 16 plastic UCLA (PUCLA) and 5 machined cast-to UCLA (GUCLA) abutments were cast with a high gold content alloy. 10 were electrolytically gold plated (8 - PUCLA, 2 - GUCLA). All abutments were attached to implants giving 21 implant-abutment combinations (IACs). External perimeter micro-gaps measured with SEM under different illumination and magnification conditions were averaged over three regions. The IACs were examined for E.coli leakage following an initial sterility test. Disassembled combinations were examined with SEM and surface profiles qualitatively assessed. Results: External micro-gap measurements did not reflect the variable connecting surface profiles but average values < 3.5 μm were observed for all IACs. Bacterial transfer was observed in 3 of 5 PUCLA plated and 2 of 5 PUCLA non-plated IACs. No transfer occurred in the 3 GUCLA non-plated or 2 GUCLA plated IACs. Abutment connecting surfaces, both Au plated and not Au plated, showed plastic deformation (smearing) in variable mosaic patterns across the micro-gap. External micro-gap dimensions although not truly reflective of surface connecting profiles averaged < 3.5 μm measured under shadow eliminating silhouette illumination for both cast and pre-machined external hexagon abutments with and without Au plating. Conclusions: Micro-gap dimensions < 5 μm were obtained with both high noble metal cast and pre-machined external hexagon abutments with and without Au electrodeposited on the abutment connecting surface. Regions of intimate contact due to plastic deformation (smearing) of these surfaces was observed. A continuous smeared region around the circumference of the surfaces can provide an effective barrier to egress of E.coli bacteria from the internal regions of the implant under static loading.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&amp;S), (ii) mechanical alloying with press and sintering (MA + P&amp;S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting &lt; MA + P&amp;S &lt; BE + P&amp;S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.

Agricultural drainage canals that connect upstream fish spawning areas to downstream rivers and lakes serve as crucial habitats for migrating fish. However, disconnections, such as drops and chutes, have been constructed in these canals due to agricultural modernization and flood control measures, hindering the movement of fish with limited swimming abilities. Portable fishways offer a promising solution to reconnect water bodies in agricultural canals, as they can be easily removed during high water discharges to avoid impeding the canals' drainage function. In addition to experimental assessments of fishway functionality, employing a hydrodynamic model to explore effective placement strategies for portable fishways is essential to maximize their effectiveness. This study presents a method to determine the best horizontal location of a portable fishway in an agricultural drainage canal using two-dimensional hydrodynamic simulations within the specified cases. The applicability of this method is demonstrated by addressing the positioning challenge of a portable fishway on a chute in an agricultural drainage canal in Japan. Results indicate that the proposed method allows for the selection of a suitable location, considering preferable hydraulic conditions both within the portable fishway and around its entrance.

Background: By using outcome prediction scores, it is possible to distinguish between good and poor performers with cochlear implants (CI) after CI implantation. The reasons for poor performance, despite good basic conditions, can be manifold. On the one hand, the postoperative fitting may be inadequate; on the other, neurophysiological disease processes may impair speech understanding with a CI. These disease processes are not yet fully understood. In acoustics, it is known that the auditory brainstem responses (ABR) and their latencies and amplitudes allow differential diagnosis based on reference values for normal-hearing individuals. The aim of this study was to provide reference values for electrically evoked brainstem responses (EABRs) in terms of rate-dependent latencies and amplitudes. Methods: 20 experienced adult CI recipients with a predicted and measured good postoperative word recognition score were recruited from the clinic’s patient pool. In the same stimulation mode and intensity we measured latencies and interpeak-latencies of EABRs and electrically evoked compound action potentials (ECAPs). With a defined supra-threshold stimulation intensity above the individual ECAP threshold, we applied stimulation at several rates between 11 and 91 stimuli per second. Results: We found rate dependences for EABR latency t3 and t5 in the order of 0.19 ms and 0.37 ms respectively, while ECAP was not affected by rate. Correspondingly, the interpeak intervalls’ rate dependences for t5-t1, t5-t3 and t3-t1 were of the order of 0.37 ms, 0.18 ms and 0.19 ms. Comparing the EABR amplitudes between the stimulation rates 11/s and 81/s, we found that at 81/s the amplitudes were significantly reduced down: to 73% for A3 and 81% for A5. These rate dependences of latency and amplitude in EABR have characteristics comparable to those of acoustic ABR. Conclusions: These data may serve to provide reference values for EABR and ECAP latencies, interpeak intervals and amplitudes with respect to stimulation rate. Altered response patterns of ECAPs and EABRs to normalised stimulation modes could be used in the future to describe and classify neuropathological processes in a better-differentiated way.

Backround Cochlear implant is the first approved cranial nerve stimulator that works by directly stimulating the cochlear nerve. Various attempts have been made to evaluate the dimensions of the cochlea related to cochlear implantationThe preoperative computed tomographic examination is essential in assessing the anatomical aspect of the cochlea, but also in determining its dimensions, in order to choose an appropriate electrode, in order to obtain the best possible audiological performance. Method In the present paper, we aimed to carry out an observational study, regarding the role of cochlear measurements in the preoperative evaluation of patients proposed for cochlear implant. The purpose of the study was to measure the cochlea and to establish the existence of a correlation between the size of the cochlea and the age and gender of the patients. Results From the group of 35 examined patients, 54% (n= 19) were male and 46% (n=16) female. The average length of the cochlea in the age group 0-4 years is 7.82 mm in the left ear and 7.86 in the right ear, in the age group 4-7 years it is 7.82 mm and 7.94 mm respectively, for the age group 7-14 years the dimensions increase to 8.48 and 8.77 mm respectively, and after 14 years these dimensions reach 9.12, respectively 9.18 mm. Comparative measurements of the length of the cochlea by age groups show an increase in length with the patient's age, but this increase does not exceed 1.5 mm for both the right and left ears. The measurements of the width of the cochlea, by age group, start from 6.84 mm left ear and 6.81 mm right ear at 0-4 years, 6.94 mm and respective 6.97 mm at the group 4-7 years, 7.71 mm and respective 7.55 mm at 7-14 years , and reaching 8.19 mmm and 8.12 mm at the age of over 14 years. Conclusions From the study carried out it can be concluded that the evaluation of the dimensions of the cochlea is important for cochlear implantation, the size variables, although small, are still an element to be considered in correlation with the age of the patient and the implanted ear. This increase is statistically insignificant, but it still exists, even if from a theoretical point of view, it is considered that the dimensions of the cochlea remain constant.

Purpose The objective of this study was to eliminate any ambiguity by examining the correlation between gut microbiota and both AMD and glaucoma. Methods Mendelian randomization studies were conducted utilizing the data sourced from the GWAS database for the gut microbiome, AMD, and glaucoma. SNP estimates were summarized through five MR methods. We utilized Cochran's Q statistic to evaluate the heterogeneity of the instrumental variables. Additionally, we employed a "leave-one-out" approach to verify the stability of our findings. Results IVW suggests that Eubacterium (oxidoreducens group) and Parabacteroides had a protective effect on AMD. Both weighted median and IVW suggests that Lachnospiraceae (NK4A136 group) and Ruminococcaceae (UCG009) had a protective effect on AMD. However, both weighted median and IVW suggests that Dorea had a risk effect on AMD. Similarly, The IVW of Eubacterium (ventriosum group) showed a risk effect on AMD. The weighted median of Eubacterium (nodatum group), Lachnospiraceae (NC2004 group), and Roseburia had a risk effect on glaucoma. IVW suggested that Ruminococcaceae (UCG004) had a risk effect on glaucoma. Reverse MR analysis found a causal link between Eubacterium (nodatum group) and glaucoma. No causal relationships were found between AMD or glaucoma and the other mentioned bacterial groups. No significant heterogeneity or evidence of horizontal pleiotropy was detected. Conclusions This study found that certain gut bacteria had protective effects on AMD, while others may be risk factors for AMD or glaucoma. Besides, reverse MR found that glaucoma led to increased abundance of certain gut bacteria. Further trials are needed to clarify the specific mechanisms involved.

In regions with limited precipitation information like Peru, many studies rely on precipitation data derived from satellite products (SPPs) and reanalysis products. These products provide near-real-time information and offer global spatial coverage, making them attractive for various applications. However, it is essential to consider their uncertainties when conducting hydrological simulations, especially in a key region like the Pacific drainage (Pd), where 56% of Peruvian population resides (including the capital Lima). This study evaluates the performance of three precipitation products: Reanalysis, ERA5-Land (top down approach), and two SPPs: GPM+SM2RAIN and SM2RAIN-ASCAT (bottom-up approaches). Hydrological modeling was conducted on 30 basins distributed across the Pd, which were grouped into five regions (I-V, ordered from south to north). The results showed that SM2RAIN-ASCAT performed well in regions I-III-IV, ERA5-Land in region II, and GPM+SM2RAIN in region V. The hydrological model GR4J was tested, and better efficiency criteria were obtained with SM2RAIN-ASCAT and GPM+SM2RAIN when comparing simulated versus observed streamflows. The hydrological modeling with SM2RAIN-ASCAT and GPM+SM2RAIN demonstrated satisfactory efficiency metrics (KGE > 0.75; NSE > 0.65). Additionally, ten hydrological signatures were quantified to assess the variability of simulated streamflows in each basin, with metrics such as Mean Flow (Q mean), 5th Quantile Flow (Q5), and 95th Quantile Flow (Q95) showing overall better performance. Finally, the results of this study demonstrate the reliability of using bottom-up satellite products in Pd basins.

Purpose: Glaucoma is the second leading cause of blindness, however, it remains incurable even with the appropriate treatment. Intraocular pressure (IOP) reduction is currently the only proven method to decline glaucoma progression. When medical therapy fails, surgical treatment usually arises as the solution to a better IOP control. Nevertheless, its success is compromised by frequent post-operative complications, most of them due to excessive fibrous tissue formation during wound healing process. Nanotechnology devices for glaucoma surgery can improve post-operative IOP control and reduce undesirable fibrosis. This systematic review aims to summarize some advances of nanotechnology application to ophthalmology, giving an overview about the state of the art of the nanotechnology based glaucoma drainage devices. Methods: A literature search in the PubMed/Medline database was performed using the keywords: “glaucoma surgery”, “glaucoma drainage device”, “nanotechnology”, “nanoparticles”, “nanomedicine” and “valve”. Were included articles published until March 1, 2023. A first identification of relevant articles was done through the title and abstract’s information, and a second selection was done by full-text articles assessment. Seven articles were included in this systematic review. Results: Nanotechnology-based glaucoma drainage devices included in this review promise to overcome the challenges of glaucoma surgical treatment by allowing a more effective control over post-operative scarring, a noninvasive and customized control of aqueous humour (AH) drainage while achieving optimal IOP reduction through all phases of the post-operative period. Conclusion: Despite the decreased post-operative complications and apparently enhanced biocompatibility of nano-based drainage devices, further in vivo tests and human studies are needed to evaluate cytotoxicity and corroborate the biocompatibility and efficacy showed in the initial testing results of these devices.

Abstract: With a resurgence in ITRT (Immediate Tooth Replacement Therapy) as a method of preserving both hard and thus soft tissues for improved aesthetic outcomes, this multi-centre, retrospective study will look at two novel products and their effect on these outcomes. A new synthetic particulate graft material along with a novel Implant design was utilized in the study and a 1 year follow up assessment, analysed for hard and soft tissue regeneration.

Hypoglossal nerve stimulator (HGNS) is a minimally invasive device used for treating obstructive sleep apnea (OSA). The conventional implantable HGNS is a device that consists of a stimuli generator, a breathing sensor, and electrodes connected to the hypoglossal nerve via leads. However, this implant is bulky and causes significant trauma. In this paper, we propose a minimally invasive HGNS based on an electrocardiogram (ECG) sensor and a wireless power transfer (WPT), consisting of a wearable breathing monitor and an implantable stimulator. The breathing external monitor utilizes an ECG sensor to identify abnormal breathing patterns associated with OSA with 88.68$\%$ accuracy, achieved through the utilization of a Convolutional Neural Network (CNN) algorithm. With a skin thickness of 5mm and a receiving coil diameter of 9mm, the power conversion efficiency was measured at 31.8$\%$. The implantable device, on the other hand, is composed of a front-end CMOS Power Management Module (PMM), a Binary Phase Shift Keying (BPSK)-based data demodulator, and a bipolar biphasic current stimuli generator. The PMM, with a silicon area of 0.06 $mm^2$ (excluding pads), demonstrates a power conversion efficiency of 77.5$\%$ when operating at a receiving frequency of 2 MHz. Furthermore, it offers three-voltage options (1.2V, 1.8V, and 3.1V). Within the data receiver component, a low-power BPSK demodulator has been ingeniously incorporated, consuming only 42 $\mu$W when supplied with a voltage of 0.7V. The performance is achieved through the implementation of the self-biased phase-locked loop (PLL) technique. The stimuli generator delivers biphasic constant currents, providing a 5-bit programmable range spanning from 0 to 2.4 mA. The functionality of proposed ECG and WPT-based HGNS was validated, representing a highly promising solution for the effective management of OSA, all while minimizing trauma and space requirements.

Background: The target volume for post-mastectomy radiation therapy (PMRT) in breast cancer patients with reconstruction has been a subject of debate. This study aimed to assess the radiation dose distribution and treatment outcomes associated with different chest wall (CW) delineation according to ESTRO ACROP guideline for patients underwent implant-based reconstruction. Methods: We conducted a retrospective review of breast cancer patients who underwent mastectomy followed by two-stage implant-based breast reconstruction and adjuvant radiation therapy (RT) between 2007 and 2022. The expanders/implants were positioned retropectorally. The chest wall target volumes were categorized into two groups: the prepectoral group, which excluded the deep lymphatic plexus, and the whole expander group. Results: The study included 26 patients, 15 in prepectoral group and 11 in whole expander group. No significant differences were observed in normal organs exposure between the two groups. There was a trend toward a lower ipsilateral lung mean dose in the prepectoral group (10.2 vs. 11.1 Gy, p=0.06). Both groups exhibited limited instances of reconstruction failure and local recurrence. Conclusions: For patients undergoing two-stage expander-implant retropectoral breast reconstruction and PMRT, our data have provided comparable outcomes and normal organs exposure for those omitting the deep lymphatic plexus.

Purpose: This study builds upon an established effective training method to investigate the advantages of high variability phonetic identification training for enhancing lexical tone perception and production in Mandarin-speaking pediatric cochlear implant (CI) recipients, who typically face ongoing challenges in these areas. Method: Thirty two Mandarin-speaking children with CIs were quasi-randomly assigned into the training group (TG) and the control group (CG). The sixteen TG participants received five sessions of high variability phonetic training (HVPT) within a period of three weeks. The CG participants did not receive the training. Perception and production of Mandarin tones were administered before (pretest) and immediately after (posttest) the completion of HVPT via lexical tone recognition task and picture naming task. Both groups participated in the identical pretest and posttest with the same time frame between the two test sessions. Results: TG showed significant improvement from pretest to posttest in identifying Mandarin tones for both trained and untrained speech stimuli. Moreover, perceptual learning of HVPT facilitated trainees’ lexical tone production as rated by a cohort of 10 Mandarin-speaking adults with normal hearing. In contrast, CG did not exhibit significant changes in either perception or production. Conclusion: The results represent initial evidence of HVPT-induced transfer of perceptual learning to lexical tone production in CI users, which supports the application of this speech training protocol to aural rehabilitation practice.

In several Indonesian tropical cities, such as Makassar City, frequent flooding during the peak rainy season poses a significant challenge. This study seeks to address this issue by devising effective policies to reduce flood exposure. The main obstacle lies in accurately determining the flood inundation area. To overcome this, the study utilizes multiple satellite data sources on a cloud platform, integrating them with land use data, and DEM data, aligning these with the local government's urban land use plan and existing drainage networks. The research aims to quantify the affected area, identify the predominant inundated land cover, and assess the efficiency of Makassar's drainage system and urban land use plan. The study reveals that an uncoordinated drainage system in the Tamalanrea, Biringkanaya, and Mangala sub-districts results in severe flooding, encompassing a total area of 35.28 km². The most affected land use type is cultivation, constituting approximately 43.5% of the flooded area. Furthermore, 82.26% of the urban land use plan, covering 29.02 km², is submerged. It is imperative for the local government and stakeholders to prioritize the enhancement of drainage systems and urban land use plans, particularly in low-lying and densely populated regions

The clinical requirement for a good esthetic result for immediate implant placement is the absence of dehiscence in the anterior facial alveolar bone. In the presence of a dehiscence, it is recommend-ed to use a connective tissue graft in addition to immediate implant placement or to change to ear-ly implant placement. However, the literature focusing on dehiscence is scarce, and the influence of different placement times and combined use of connective tissue graft on postoperative esthetics in cases with dehiscence is unclear. Therefore, we quantitatively evaluated the pre-extraction de-hiscence morphology and postoperative changes in the facial tissue of implants in three groups: immediate implant placement (Group I), immediate implant placement with connective tissue graft (Group IC), and early implant placement (Group E). Fifty-two implants were obtained (20 in Group I, 16 in Group IC, and 16 in Group E). A wider dehiscence increases the risk of soft tissue regression, which was one reason for choosing early implant placement. A combination of imme-diate implant placement and connective tissue graft, or early implant placement, tended to result in less soft tissue regression due to the thicker postoperative facial soft tissue volume.

Irrigation and debridement using an irrigation solution is a fundamental step during the surgi-cal treatment of both acute and chronic periprosthetic joint infection (PJI). However, there is no consensus on the optimal solution, nor is there sufficient evidence on optimal irrigation time and combination of solutions. Therefore, it is necessary to determine which solution or combi-nation of solutions is most efficacious against biofilm, as well as the optimal irrigation time. We conducted an experimental in vitro model by inoculating stainless steel discs with ATCC strains of methicillin-susceptible Staphylococcus aureus, methicillin-resistant S. aureus, Pseudomonas aeru-ginosa, and a clinical strain of Staphylococcus epidermidis. The discs were all irrigated with com-monly used antiseptic solutions (10% and 3% povidone iodine, hydrogen peroxide, 3% acetic ac-id, and Bactisure™) for 1 min, 3 min, and 5 min and their combinations for 9 min (3 min each) vs. sterile saline as a positive control. We evaluated the reduction in biofilm based on colony form-ing unit (cfu) counts and, in combination assays, also based on cell viability and scanning elec-tron microscopy. All antiseptics alone reduced more than 90% of cfu counts after 1 min of irriga-tion; the worst results were for hydrogen peroxide and 3% acetic acid. When solutions were combined, the best results were observed for all those starting with acetic acid, in terms of both reduction of log cfu/ml counts and viable cells. We consider that a combination of antiseptic so-lutions, particularly that comprising the sequence acetic acid+povidone iodine+hydrogen per-oxide, would be the best option for chemical debridement during PJI surgery.

Electric stimulation via a Cochlear Implant (CI) enables people with severe to profound sensorineural hearing loss to regain speech understanding and music appreciation and thus allowing them to actively engage in social life. Three main manufacturers (Cochlear, MED-EL and Advanced Bionics “AB”) have been offering CI systems, thus challenging CI recipients and Otolaryngologists with a difficult decision, as currently no comprehensive overview or meta-analyses on performance outcome following CI implantation is available. The main goal of this scoping review is to provide evidence that data and standardized speech and music performance tests are available for performing such comparisons. To this end, a literature search was conducted to find studies that address speech and music outcomes in CI recipients. From a total of 1592 papers, 188 paper abstracts were analyzed and 147 articles were found suitable for examination of full text. From which, 42 studies were included for synthesis. A total of 16 studies used the consonant-nucleus-consonant (CNC) word recognition test in quiet at 60db SPL. We found that aside from technical comparisons, only very few publications compare speech outcomes across manufacturers of CI systems. Evidence suggests though, that these data are available in large CI centers in Germany and US. Future studies should therefore leverage large data cohorts to perform such comparisons that could provide critical evaluation criteria and assist both CI recipients and Otolaryngologists to make informed performance-based decisions.

Sacroiliac (SI) joint dysfunction can lead to debilitating pain but can be treated with minimally invasive sacroiliac joint fusion (SIJF). This treatment is commonly performed using 2D fluoroscopic guidance. This makes placing the implants without damaging surrounding neural structures challenging. Virtual surgical planning (VSP) using simulated fluoroscopic images may improve perioperative guidance. This article describes a workflow with VSP in SIJF using simulated fluoroscopic images and evaluates achieved implant placement accuracy. Routinely collected survey data on the added value of VSP were also evaluated. Ten interventions were performed on 10 patients by the same surgeon, comprising 30 implants; the median age was 39 years, and all patients were female. The overall mean implant placement accuracy was 4.9 ± 1.26 mm and 4.0 ± 1.44°. There were no malpositioning complications. The VSP helped the surgeon understand the anatomy and determine the optimal position and length of the implants. The average Likert scale score of the survey was 4.7, suggesting a positive role of VSP for SIJF. Planned positions of the implants could be reproduced in surgery with clinically acceptable accuracy and VSP was a valuable asset for the surgeon.

Alveolar bone atrophy after tooth extraction presents significant difficulties when planning delayed-immediate implant treatment to replace a lost tooth. Socket augmentation is an effective therapy that limits the post extraction volumetric changes and facilitates implant placement whilst reducing the need for staged grafting. However, socket augmentation and osteoconductive graft conversion is a slow process that could take 4-6 months. PRF and its variants have significant bio-enhancement effect on wound healing and regeneration through release of platelet drived growth factors, bioactive substances, cytokines. Leukocytes in PRF also play a significant role in enhancing tissue regeneration as part of osteo-immune response. Use of PRF during socket augmentation is highly effective in enhancing extraction site healing and graft integration by angiogenesis, cell proliferation, recruitment, and differentiation through release of growth factors and bioactive substances mediated by platelets and leukocytes. PRF with SA is recommended as an adjunct to SA as a sole biomaterial or in combination with xenograft or allograft bone substitutes to enhance tissue regeneration and to reduce risk of infection, osteitis and postoperative pain in extraction sockets

Abstract: The glucocorticoid receptor (GR), including both alternative spliced isoforms (GRa and GRb), has been implicated in the development of primary open-angle glaucoma (POAG) and iatrogenic glucocorticoid-induced glaucoma (GIG). POAG is the most common form of glaucoma, which is the leading cause of irreversible vision loss and blindness in the world. Glucocorticoids (GCs) are commonly used therapeutically for ocular and numerous other diseases/conditions. One serious side effect of prolonged GC therapy is the development of iatrogenic secondary ocular hypertension (OHT) and OAG (i.e. GC-induced glaucoma (GIG)) that clinically and pathologically mimics POAG. GC-induced OHT is caused by pathogenic damage to the trabecular meshwork (TM), a tissue involved in regulating aqueous humor outflow and intraocular pressure. TM cells derived from POAG eyes (GTM cells) have lower expression of GRb, a dominant negative regulator of GC activity, compared to TM cells from age-matched control eyes. Therefore, GTM cells have a greater pathogenic response to GCs. Almost all POAG patients develop GC-OHT when treated with GCs, in contrast to a GC responder rate of 40% in the normal population. Increased expression of GRb can block GC-induced pathogenic changes in TM cells and reverse GC-OHT in mice. Endogenous expression of GRb in the TM may relate to differences in the development of GC-OHT among the normal population. A number of studies have suggested increased levels of endogenous cortisol in POAG patients as well as differences in cortisol metabolism, suggesting that GCs may be involved in the development of POAG. Additional studies are warranted to better understand the molecular mechanisms involved in POAG and GIG in order to develop new disease modifying therapies to better treat these two sight threatening forms of glaucoma.

A maxillary totally edentulism was rehabilitated with one-piece implants starting from pre-existing totally removable denture. A 3D digital scan of the removable denture and upper and lower arches was performed. On this basis, a prototype with optimal esthetic and functional outcomes was re-alized and turned into a custom-made radiological stent with markers. The superimposition of STL and DICOM files allowed the virtual planning of one-piece implants ideal position. The stackable templates composed of a fixed component, namely base template, and removable components, were realized. The fixed component, once secured with anchor pins to the bone, was no longer removed. The removable components, screwed to the fixed component, were used to perform the implant surgery and the immediate prosthetic loading. A base template allowed for maintaining a fixed reference during the entire workflow, improving the transition between the digital project, the surgical procedure, and the prosthetic rehabilitation.

(1) Importance of problem: Breast cancer accounted for 685.000 deaths globally in 2020, and half of all cases occur in women with no specific risk factor beside gender and age-group. During last 4 decades we see a reduction by 40% of age-standardized breast cancer [1], which in turn means that the number of mastectomies performed for younger women increased, raising the need for adequate breast reconstructive surgery. Advances in oncological treatment have made it possible to limit the extent of what represents radical surgery for breast cancer, yet in the past decade, we see a marked trend toward mastectomy in breast conserving surgery eligible patients [2]. Prophylactic mastectomy has also registered an upward trend [3,4]. This trend together with new indication for breast reconstruction like chest feminization in transgender patients [5] have increased the need for breast reconstruction surgery. (2) Purpose: The purpose of this study is to analyze the types of reconstructive procedures, their indications, their limitations, their functional results and the safety profiles when used during the integrated treatment plan of the oncologic patient; (3) Methods: We conducted an extensive literature review of the main reconstructive techniques, especially the autologous procedures, summarized the findings and presented a few cases from our own experience for exemplification of the usage of breast reconstruction in oncologic patients. (4) Conclusions: Breast reconstruction has become a necessary step in the treatment of most breast cancers and many reconstructive techniques are now routinely practiced. Microsurgical techniques are considered the "gold standard", but they are not accessible to all services, from a technical or financial point of view, so pediculated flaps remain the safe and reliable option, along with alloplastic procedures, to improve the quality of life of these patients.

There are several pathologies that can change the anatomy of the otic capsule and that can distort the bone density of the bony structures of the inner ear, but otosclerosis is one of the most frequent. Similar behavior has been shown in patients affected by osteogenesis imperfecta (OI), a genetic disease due to a mutation in the genes coding for type I (pro) collagen. In particular, we note that otosclerosis and OI can lead to bone resorption creating pericochlear cavitations in contact with the internal auditory canal (IAC). In this regard, in our experience we have collected 5 cases presenting this characteristic and their audiological data and clinical history were analyzed. This feature can be defined as a potential cause of a third-window effect, because it causes an energy loss during the transmission of sound waves from the OW away from the basilar membrane.

Glaucoma secondary to Peters' anomaly (PA) is an important factor affecting visual prognosis, but there are few reports on it. This study aimed to investigate the characteristics of glaucoma asso-ciated with PA and glaucoma surgery outcomes. This retrospective study included 31 eyes of 20 patients with PA. PA was classified into three stages: Stage 1, with a posterior corneal defect only; Stage 2, a corneal defect with iridocorneal adhesion; and Stage 3, a corneal defect with lens ab-normalities. The associations between glaucoma and anterior segment dysgenesis severity, visual prognosis, and glaucoma surgery outcomes were analyzed. Sixteen eyes of 10 patients developed glaucoma. Stage 1 PA had no glaucoma, 52% of Stage 2 had glaucoma, and 75% of Stage 3 had glaucoma. Of the 16 eyes with glaucoma, 11 underwent surgery. Eight of these 11 eyes achieved intraocular pressure (IOP) control. Five of the nine eyes that underwent trabeculotomy (TLO) succeeded, and none had corneal staphyloma. Three of the four eyes for which TLO was ineffective had corneal staphyloma (P=0.0331). Patients with PA are more likely to develop glaucoma as anterior segment dysgenesis progresses, and the effect of TLO is limited if corneal staphyloma is present.

The incidence of breast cancer and therefore need for breast reconstruction is expected to increase. The many reconstructive options available and the changing aspects of the field make this a complex area of plastic surgery, requiring knowledge and expertise. Two major types of breast reconstruction can be distinguished: Breast Implants and Autologous Flaps. Both present advantages and disadvantages. Autologous fat grafting is also commonly used. MRI is the modality of choice for evaluating breast reconstruction. Knowledge of the type of reconstruction is preferable to provide the maximum of pertinent information and avoid false positives. Early complications include seroma, hematoma, and infection. Late complications depend on the type of reconstruction. Implant rupture and implant capsular contracture are frequently encountered. Depending on the implant type, specific MRI signs can be depicted. In case of myocutaneous flap, fat necrosis, fibrosis and vascular compromise represent the most common complications. Late cancer recurrence is much less common. Rare reported late complications include breast implant associated large cell anaplastic lymphoma (BIA-ALCL) and, recently described and even rarer, Breast implant-associated squamous cell carcinoma (BIA-SCC). In this review article, the various types of breast reconstruction will be presented, with emphasis on pertinent imaging findings and complications.

Chlorhexidine digluconate (CHX) has shown the ability to significantly reduce inflammation and marginal bone loss (MBL) at 1-year follow-up but limited data exists regarding its long-term efficacy in peri implant stability. The objective was to compare the long-term effects of a placebo gel (16 patients in Group A) or a 0.20% CHX gel (15 patients in Group B) used at each previous surgical and prosthetic stage. Follow-ups were conducted in 2022, investigating by biological, radiological, clinical, mechanical evaluation the long-term effects. Data were statistically analyzed. The research achieved a 96.7% implant success rate over five years, but 41.9% of patients didn't attend annual oral hygiene check-ups. The average MBL was 1.04 ± 0.39 mm, with no significant differences between the two groups. Notably, patients who attended regular periodontal check-ups experienced significantly less MBL than those who didn't (p &lt;0.05). At five years, the effects of CHX were reduced, with both groups showing moderate bone loss. The results suggest early disinfection could enhance both short and long-term outcomes. In fact, patient with initial minor MBL preserve this advantage also at 5 years of follow-up. Additionally, the data underscore the importance of annual check-ups in early detection and management of biological and mechanical complications.

Purpose: To compare refractive prediction error (PE)s between phacotrabeculectomy and phacoemulsification. Methods: Refractive PE was defined as the difference of spherical equivalent between the predicted value using the Barrett Universal II formula and the actual value obtained at postoperative one month. Forty-eight eyes that had undergone phacotrabeculectomy (19 eyes, open-angle glaucoma; 29 eyes, angle-closure glaucoma) were matched with 48 eyes that had undergone phacoemulsification by age, average keratometry value and axial length (AL), and their PEs were compared. The factors associated with PE were analyzed by multivariable regression analyses. Results: Phacotrabeculectomy group showed a larger absolute PE compared to the phacoemulsification group (0.51 ± 0.37 Diopters vs. 0.38 ± 0.22, P=0.033). Larger absolute PE was associated with longer AL (P=0.010) and higher intraocular pressure (IOP) difference (P=0.012). Hyperopic shift (PE>0) was associated with shallower preoperative anterior chamber depth (ACD) (P=0.024) and larger IOP difference (P=0.031). In the phacotrabeculectomy group, the PE was inversely correlated with AL: long eyes showed myopic shift and short eyes hyperopic shift (P=0.002). Conclusions: Surgeons should be aware of the possibility of worse refractive outcomes when planning phacotrabeculectomy especially in eyes with high preoperative IOP, shallow ACD, and/or extreme AL.

This review provides a comprehensive overview of two major advancements in hearing loss treatment: the middle ear implant (MEI) and bone conduction implants (BCIs). MEI, surgically inserted in the middle ear, directly stimulate the ossicles, and are primarily employed to treat sensorineural, conductive, or mixed hearing losses. BCIs work via bone conduction, bypassing the outer and middle ear to deliver sound vibrations to the inner ear, beneficial especially for conductive or mixed hearing losses and single-sided deafness. The decision to opt for these devices is a multifaceted process, considering audiological criteria, surgical feasibility, and patient expectations. The review also details the portfolio of available devices, their functioning, and audiological usage indications. While both MEI and BCIs prove beneficial for patients, the review emphasizes the need for careful preoperative planning and counselling, considering factors such as potential complications, surgical challenges, and patient suitability. Overall, the two types of implants, despite their individual complexities, provide an effective alternative to traditional hearing aids, offering a path to improved sound clarity and quality for patients with various types of hearing loss.

This study describes the AMD impacted environments and critically discusses the effects of AMD, current prediction and prevention methods and treatment technologies. The study further, crit-ically analyses the case studies, gaps in AMD research and the challenges and opportunities of-fered by AMD. The study outlined future technological intervention aiming at a paradigm shift towards reducing the volume of sludge generated as well as the operating cost and improving AMD treatment efficiency. The integrated AMD treatment technologies that result in a holistic approach toward sustainable AMD treatment are a current need. As a result, a sustainable AMD treatment strategy has been made possible due to water reuse and rich resource recoveries such sulphuric acid, rare earth elements, and metals. The cost of AMD treatment can be decreased with the use of recovered water and resources, which is essential for developing a sustainable AMD treatment process.

A surgical technique aimed at rerouting aqueous humor (AH) outflow from the anterior chamber to the suprachoroidal space (SCS) without performing surgical cyclodialysis was developed to decrease intraocular pressure (IOP) in glaucoma patients. The surgical outcomes of the technique were retrospectively analyzed in fifty-eight patients. At 6, 12, and 24 months, the mean IOP decreased from 27.8±8.3 to 14.95.0 mmHg, median 15.0 (25th percentile (p25 )13.0; 75th percentile (p75) 18.0), and 15.23.3 mmHg; hypotensive medication use reduced from median (p25; p75) 3 (2; 3) to 0 (0; 2), 0 (0; 2), and 0 (0; 1.5), and complete success was achieved in 62.8%, 51.2%, and 32.5% cases, with partial success in 28.4%, 44.2%, and 62.5% cases, respectively. Eight cases (13.8%) presented unsatisfactory outcomes. Intra- and postoperative complications were few and manageable. No bleb formation was observed in any of the cases. In 50% of cases, conjunctival lymphatic vessels (CLVs) developed following surgery in superior quadrants. The technique is safe and effective in providing a long-term decrease in IOP and hypotensive medication use. It was hypothesized in this study that the IOP decrease occurred as a result of enhanced AH outflow from the SCS to CLVs through intrascleral microchannels connecting the SCS to CLVs.

Progressive loss of retinal ganglionic cells (RGC) causes blindness in glaucoma. Elevated intraocular pressure (IOP) is the most important, treatable risk factor. Currently, the management of glaucoma is centred at reducing the IOP, and drugs in the form of topical drops are the first line of management. Drugs reduce IOP either by suppressing aqueous humour secretion or improving the aqueous humour outflow. Newer drugs added during the past three decades to the armamentarium of glaucoma treatment have targeted the aqueous outflow. With an evolving understanding of the pathogenesis of glaucoma, the role of 24-hour IOP control and other IOP-independent risk factors affecting ocular blood flow and RGC toxicity is also recognised. The role of available drugs in controlling IOP over 24-hours is being evaluated. Improvement of ocular blood flow and neuroprotection are seen as potential drug targets in preventing the loss of RGC. In this article, we review the pharmacotherapy of glaucoma based on current therapeutic principles.

This study aimed to compare the efficacies and safety of enhanced and standard monofocal intraocular lenses (IOLs) in eyes with early glaucoma. Patients with concurrent cataracts and open-angle glaucoma (OAG) were enrolled. They underwent cataract surgery with IOL implantation. Manifest refraction; monocular uncorrected distance visual acuity (UDVA), corrected distance visual acuity (CDVA), uncorrected intermediate visual acuity (UIVA), and uncorrected near visual acuity (UNVA); visual field (VF); contrast sensitivity (CS); defocus curves and questionnaires were assessed three months postoperatively. Thirty-four and 38 patients had enhanced and standard monofocal IOLs, respectively. The enhanced monofocal IOL provided better UIVA than the standard monofocal IOL (p = 0.003) but similar UDVA, CDVA and UNVA. The enhanced monofocal IOL had more consistent defocus curves than the standard monofocal IOL, especially at -1 (p = 0.042) and -1.5 (p = 0.026) diopters. The enhanced monofocal IOL provided better satisfaction (p = 0.019) and lower spectacle dependence (p = 0.004) than the standard monofocal IOL for intermediate vision, with similar VF and CS. In conclusion, the enhanced monofocal IOL is recommended for patients with OAG because they provide better intermediate vision, higher satisfaction, and lower dependence on spectacles than standard monofocal IOL, without worsening other visual outcomes.

Enophthalmos is a severe complication of primary reconstruction following orbital floor frac-tures, oncological resections or maxillo-facial syndromes. The goal of secondary reconstruction is to re-store symmetrical globe positions to recover function and aesthetics. In this article we pre-sent a method of computer-assisted orbital floor reconstruction using a mirroring technique and a customized titanium or high-density polyethylene mesh, printed using computer aided manufac-turing techniques. This reconstructive protocol involves 4 steps: mirroring of the healthy orbit at the affected site, vir-tual design of a patient specific orbital floor mesh, computer-assisted manufacturing (CAD) of the implant, and surgical insertion of the device. Using a computed tomography data set, the un-injured side of the craniofacial skeleton was reflected onto the contralateral injured side, and a reconstructive orbital floor prosthesis was virtually designed on the mirrored orbital bone sur-face. The solid-to-layer (.STL) files of the prosthesis were then manufactured using Direct Metal Laser Sintering (DMLS) or Computer Numerical Control (CNC) methods, leading to the produc-tion of 10 titanium meshes and 2 high density polyethylene (HDPE) implants. Clinical outcomes were assessed using 3dMD photogrammetry and computed tomography measures in 14 treated patients. The technique described here appears to be a viable method to correct complex orbital floor de-fects needing delayed reconstruction. This article represents the prosecution of a previous study, which is part of a wider experimental protocol for orbital floor reconstruction using comput-er-assisted design-computer-assisted manufacturing (CAD-CAM) technology

The purpose of this study was to evaluate the outcomes of implants placed in horizontally augmented alveolar ridges using porcine bone grafts and to investigate the long-term stability of the porcine bone grafts. A retrospective analysis was conducted on 55 sites that underwent horizontal ridge augmentation using porcine bone grafts and implant placement with a follow-up period longer than 5 years. Furthermore, additional analysis was conducted on 24 sites where porcine bone grafts were used exclusively and implants were placed simultaneously with horizontal ridge augmentation. The mean follow-up period after prosthesis loading was 67.3 months, with a mean marginal bone loss of 0.18 mm at 1 year and a cumulative mean marginal bone loss of 0.37 mm over the entire follow-up period. Of the 55 implants, 2 were lost and 4 did not meet the success criteria, resulting in a survival rate of 96.4% and a success rate of 89.1%. In 24 sites, the mean marginal bone loss was 0.22 mm at 1 year and 0.40 mm at 65.8 months, with 100% survival and success rates. Porcine bone grafts can be successfully used in horizontal ridge augmentation for implant placement in cases of ridges with insufficient horizontal width.

(1) Background: Melanoma is the most aggressive tumor located at the skin level and the man-agement of this pathology requires a correct staging as well as a modern oncological treatment, adapted to each patient. The main objective of the study is to determine the variability of lymphatic drainage in the case of melanomas located on the trunk; (2) Methods: This retrospective study in-cluded 62 cases of melanoma located on the trunk operated between July 2019 and March 2023 in which SLNB was performed and a total of 84 lymph node were excised; (3) Results: Patients had an average age of 54.5 years old, while melanomas had a mean Breslow index of 2.3 mm. The distri-bution of trunk melanomas was: upper trunk 54 cases, lower trunk 30 cases (64.3 % vs. 35.7%). The type of anesthesia chosen was general anesthesia in 53 cases, respectively spinal anesthesia in 9 cases (85.5% vs. 14.5%, p<0.001). The number of sentinel lymph nodes was 54 for melanomas lo-cated on the upper trunk, 8 cervical and 46 axillary, respectively 30 sentinel lymph nodes in cases of melanomas of the lower trunk, 16 at the axillary level and 14 at the inguinal level; (4) Conclusions: Lymph node involvement in melanoma represents an important prognostic factor and the different lymphatic drainage pathways in relation to the location of the primary tumor represents an im-portant objective in the management of this pathology.

Despite the high biocompatibility of titanium and its alloys, the need to remove titanium implants is increasingly being debated due to the potential for adverse effects associated with long-term retention. Therefore, new solutions are being sought to enhance the biocompatibility of titanium implants. One of them is to increase the thickness of the passive layer of the implant made of titanium dioxide. We were the first to evaluate the effect of hard-anodized (type II) Ti-6Al-4V alloy discs on the cytotoxicity, mitochondrial function and redox balance of mitochondrial fibroblasts compared to standard-anodized (type III) and non-anodized discs. The study used fibroblasts obtained from human gingival tissue. The test discs were applied to the bottom of 12-well plates. Cells were cultured for 24h and 7; 14 and 21 days and mitochondria were isolated. We demonstrated the occurrence of oxidative stress in the mitochondria of fibroblasts of all tested groups, regardless of the presence and type of anodization. Type II anodization prevented changes in complex II activity (vs. control). The lowest degree of citrate synthase inhibition occurs in mitochondria exposed to titanium discs with type II anodization. In the last phase of culture, the presence of type II anodization reduces the degree of cytochrome c oxidase inhibition compared to the other tests groups and the control group, and prevents apoptosis. Throughout the experiment, the release of titanium, aluminium and vanadium ions from titanium discs with a hard-anodized passive layer was higher than from the other titanium discs, but decreased with time. The obtained results prove the existence of dysfunction and redox balance in the mitochondria of fibroblasts exposed to hard-anodized titanium discs, suggesting the need to search for new materials perhaps biodegradable in tissues of the human body.

The North Railway in the Kingdom of Saudi Arabia (KSA) extends over vast areas, crossing various terrains, including valleys, sand veins, plateaus, and hills. Therefore, the Railway was designed and implemented to suit this environmental diversity under the highest safety standards. However, the Railway may be subject to hazards for various reasons. In general, the possibility of direct surface runoff disasters increases if there are residential areas and facilities within the boundaries of drainage basins. Therefore, these areas should be studied, and the degree of hazard in drainage basins should be accurately determined. Hence, this study analyzed the degree of risk of 14 drainage basins affecting the North Train railway within the Wadi Malham drainage basin, using the risk degree model with eight parameters that have hydrological indications to give an idea of the behavior of direct surface runoff and interfere with increasing the risk of direct surface runoff. Researchers found 28.57% of the total basins in the study area have high-risk basin overall score values, which are basins 6, 7, 13, and 14. It is recommended to estimate the rainfall depth during different return periods, analyze soil permeability and land use classification in the study area, and apply hydrological modeling of drainage basins, which contributes to estimating the volume and peak of direct surface runoff in such arid and semi-arid environments that do not contain hydrometric stations to monitor the runoff. .

Glaucoma, a group of diseases characterized by progressive retinal ganglion cell loss, cupping of the optic disc and by a typical pattern of visual field defects, is a leading cause of severe visual impairment and blindness worldwide. Elevated intraocular pressure (IOP) is the leading risk factor for glaucoma development. However, glaucoma can also develop at normal pressure levels. An increased susceptibility of retinal ganglion cells to IOP, systemic vascular dysregulation, endothelial dysfunction and autoimmune imbalances have been suggested to play a role in the pathophysiology of normal tension glaucoma. Since inflammation and oxidative stress play a role in all forms of glaucoma, the goal of this review article is to resent an overview on the inflammatory and prooxidant mechanisms in the pathophysiology of glaucoma and to discuss immunomodulatory and antioxidant treatment approaches.

Background: We compared corneal visualization Scheimpflug technology (CST) parameters between eyes with primary open-angle glaucoma (POAG) and primary angle-closure glaucoma (PACG). Methods: A retrospective analysis was done on data from 89 eyes with POAG and 83 eyes with PACG that had CST examinations. CST parameters were compared between eyes with POAG and those with PACG using a linear mixed model (LMM). Results: No differences were observed in age, central corneal thickness, intraocular pressure, or use of antiglaucoma eye drops between the two groups. Patients with PACG had a significantly shorter axial length (AL), a higher proportion of females, CST parameters, longer applanation 2 (A2) time, deeper A2 deformation amplitude, shorter peak distance (PD), longer whole eye movement, and longer whole eye movement time than patients with POAG. Highest concavity (HC) length and PD showed a significant positive correlation with AL. However, A1 length, A1 deformation amplitude, A2 time, A2 velocity, A2 length, A2 deformation amplitude, HC time, whole eye movement, and whole eye movement time were negatively correlated with AL. Conclusions: Biomechanical properties of the cornea differed between PACG and POAG. In some parts, AL differences between the POAG and PACG groups might contribute to the variation in CST parameters.

Background - Mandibular flexion (MF) is a complex biomechanical phenomenon, which involves a deformation of the mandible, due mainly to the contraction of the masticatory muscles, and can have numerous clinical effects. The main aim of the current systematic review is to highlight the different factors that can increase MF, to help clinicians, identify patients to whom they should pay more attention. As a secondary outcome, we wanted to analyze the preventive measures and suitable techniques to be adopted to minimize the negative effects of this phenomenon on oral fixed rehabilitations. Methods - The review, which was carried out in accordance with the “Preferred Reporting Items for Systematic reviews and Meta-Analyses” (PRISMA) flowchart, was recorded in the “International Prospective Register of Systematic Reviews” (PROSPERO). As research questions, “Patient/Population, Intervention, Comparison and Outcomes” (PICO) questions were employed. Using the ROBINS-I technique, the risk of bias in non-randomized clinical studies was evaluated. Results - The initial electronic search identified over 1300 potential articles, of which 54 studies were included in this systematic review. Information regarding the relationship between MF and individual factors, mandibular movements, impression-taking and fixed rehabilitations were obtained. Conclusions – The studies included in this systematic review showed that MF is greater during protrusive movements, in the posterior areas of the lower jaw, and in patients with brachial facial type, greater jaw length, small gonial angle and less density, length and bone surface of the symphysis. The biomechanical effects of mandibular flexion on fixed restorations are debated. Prospective clinical and radiological observational studies should be conducted to evaluate the potential short-, medium- and long-term consequences of MF.

Titanium (Ti) and Ti-based alloys are commonly used in dental implants, and surface modifications of dental implants are important for achieving osseointegration (i.e., direct connection between the implant surface and bone). This study investigated the effect of an eco-friendly etching solution—a hydrogen peroxide–sodium bicarbonate mixture—on the surface properties and contact angles of and osteoblast adhesion and proliferation on Ti surfaces. Disk-shaped Ti specimens were prepared using different surface treatments (machining, sandblasting, and sandblasting/acid-etching), and they were immersed in the etching solution and then ultrasonically cleaned. Surface characterization was performed using scanning electron microscopy, digital microscopy, contact angle analysis, and X-ray photoelectron spectroscopy. MG-63 osteoblasts were cultured on the specimens, and their adhesion to the specimen surface and their proliferation were examined using staining and the MTT assay, respectively. Additional etching with the etching solution caused the formation of nano/micro hierarchical structures, increased the surface roughness, and enhanced the hydrophilicity. Osteoblast adhesion and proliferation were found to improve on the modified surfaces. The eco-friendly etching method has the potential to enhance the biological properties of Ti implant surfaces and to thereby improve the dental implant performance.

Visual impairment and blindness are a growing public health problem, as they reduce the quality of life of millions of people. The management and treatment of these diseases represent a scientific and therapeutic challenge, since the different cellular and molecular actors involved in the pathophysiology are still being identified. The visual system components, particularly the retinal cells, are extremely sensitive to genetic or metabolic alterations, and immune cells activated by insults contribute to biological events that culminate with vision loss and irreversible blindness. Several ocular diseases are linked to retinal cell loss, and diseases such as retinitis pigmentosa, age-related macular degeneration, glaucoma and diabetic retinopathy are characterized by pathophysiological hallmarks that represent possibilities to study and develop novel treatments for retinal cells degeneration. Here, we present a compilation of revisited information on retinal degeneration, including pathophysiologic and molecular features, biochemical hallmarks and possible directions for novel treatments, aiming to assist as a guide for innovative research. The expansion of knowledge of the mechanistic bases of the pathobiology of eye diseases, including information on the complex interactions of genetic predisposition, chronic inflammation, and environmental and aging-related factors will allow the identification of new therapeutic strategies.

Background: This systematic umbrella review aims to investigate whether provide an analysis of guidelines regarding the treatment of diverticular abscesses summarizing the evidences from the best available practice. Material and methods: A systematic literature search was performed until using the Cochrane Overviews of Reviews model for search the ‘Clinical Practice Guidelines’; at the end of initial search only 12 guidelines, whose characteristics are reported in the following table were included in this analysis. The quality of the guidelines was assessed by adopting the 2017 updated version of the “Appraisal of Guidelines for Research and Evaluation II” (AGREE II). The comparative analysis of these guidelines has highlighted the presence of some differences regarding the recommendations on the treatment of diverticular abscesses. In particular, there are some controversies about the diameter of abscess to be used in order to decide between medical treatment and percutaneous drainage. Different guidelines propose different abscess diameter cutoffs, such as 3 cm, 4-5 cm, or 4 cm, for distinguishing between small and large abscesses. Conclusions: Currently, a lot of scientific societies recommend that diverticular abscesses with diameters larger than 3 cm should be considered for percutaneous drainage whereas abscesses with diameters smaller than 3 cm could be appropriately treated by medical therapy with antibiotics; only, few guidelines, suggest the use of percutaneous drainage for abscess with a diameter greater than 4 cm .The difference among guidelines is the consequence of the different selection of scientific evidences. In conclusion, our evaluation has revealed the importance of seeking new scientific evidence with higher quality to either confirm, reinforce or potentially weaken the existing recommendations from different societies.

Optic nerve disorders encompass a wide spectrum of conditions characterized by the loss of retinal ganglion cells (RGCs) and subsequent degeneration of the optic nerve. The etiology of these disorders can vary significantly, but emerging research highlights the crucial role of oxidative stress, an imbalance in the redox status characterized by an excess of reactive oxygen species (ROS), in driving cell death through apoptosis, autophagy, and inflammation. This review provides an overview of ROS-related processes underlying four extensively studied optic nerve diseases: glaucoma, Leber's hereditary optic neuropathy (LHON), anterior ischemic optic neuropathy (AION), and optic neuritis (ON). Furthermore, we present preclinical findings on antioxidants, with the objective of evaluating the potential therapeutic benefits of targeting oxidative stress in the treatment of optic neuropathies.

Peri-implant bone resorption has been reported around some implants after loading and this could create problems for the long-term stability of peri-implant soft and hard tissues. The causes are still not completely known, but a relevant importance could be assumed by the presence of a bacterial contamination at the micro-gap level of the implant-abutment junction. In this regard, external and internal implant-abutment assemblies have been shown to be much more permeable to bacterial colonization than Cone-Morse or conical connections. A subcrestal implant placement could have aesthetic advantages allowing a better prosthetic emergence profile. In literature controversial experimental and clinical results have been reported about bone resorption around implants placed equicrestally and subcrestally. Interestingly, Finite Element Analysis (FEA) studies revealed to be extremely useful for assessing the peri-implant bone strain and stress. Thus, the aim of this study was a FEA evaluation of implants with a Cone-Morse implant-abutment assembly (Implacil De Bortoli, São Paulo, Brazil) inserted into a bone block model (width: 10 mm, vertical height: 17.5 mm, thickness of the cortical area: 1.5 mm) mimicking equicrestal and subcrestal placements (1 and 2 mm). The results demonstrated that maximum stresses were observed within the cortical bone around the equicrestally placed implants, the lowest in the implant placed 2-mm subcrestally and intermediate stresses within the implant placed 1-mm subcrestally. Cortical bone was more stressed under lateral loads than axial loads. In conclusion, this FEA study suggested that implant placement at -1 mm could be recommended.

Surface chemistry evaluation plays a crucial role in assessing the efficacy of chemical decontamination products for titanium implants. This study aimed to investigate the effectiveness of chemical decontamination solutions in cleaning a contaminated dental implant surface and to evaluate the potential of combining Pluronic gel with hydrogen peroxide (NuBone®Clean) by evaluating pellicle disruption and re-formation on implant surfaces. In addition, ensuring safety with in- vitro and human testing protocols. X-ray Photoelectron Spectroscopy (XPS) was utilized for surface analysis. All the tested gels had some effect on the surface cleanness except for PrefGel®. Among the tested chemical decontamination candidates, NuBone®Clean demonstrated effectiveness in providing a cleaner titanium surface. Furthermore, none of the tested chemical agents exhibited any cytotoxic effects, and the safety assessment showed no adverse events. The results of this study highlight the significance of conducting comprehensive evaluations, encompassing safety and efficacy, before introducing new chemical agents for dental treatments. The findings suggest that NuBone®Clean shows potential as a chemical decontamination solution for implant surfaces. However, further investigation through randomized clinical trials is necessary. By adhering to rigorous testing protocols, the development of safe and efficient chemical decontamination strategies can be advanced, benefiting patients and promoting progress in the field of implant dentistry.

Two-stage surgery is unintentionally necessary when total tumor removal cannot be accomplished in the first surgery, although, it has not yet been established how to leave the tumor for the next surgery. There is a risk of postoperative hemorrhage in the residual tumor, especially in hypervascular tumors. We report a case of hypervascular choroid plexus papilloma in which preservation of intratumoral venous drainage was considered important to avoid hemorrhagic complications during a two-stage surgery. In hypervascular tumor resection, to prevent postoperative hemorrhage associated with a residual tumor, it may be important to preserve venous drainage of the tumor.

Insufficient oral ridge tissue presents a challenge in the treatment of dental implants. One method to enhance alveolar crest dimensions is guided bone regeneration (GBR); however, existing membranes have certain limitations. To address this issue, we aimed to compare the effectiveness of a resorbable bilayer membrane composed of poly(l-lactic acid) and poly(-caprolactone) （PLACL）with that of a collagen membrane（COL） in a rat GBR model. The rat calvaria was used as an experimental model by placing a plastic cylinder. Forty male Fisher rats underwent surgery, and micro-computed tomography and histomorphometric analyses were performed to assess bone regeneration. The results showed that bone regeneration was similar across all the groups. However, after 24 weeks, the PLACL membrane demonstrated significant resilience, occasional partial degradation, and intermittent air bubble formation. This extended preservation of the barrier effect has great potential to facilitate optimal bone regeneration. In conclusion, this study shows that the PLACL membrane is a promising alternative to GBR. By providing a durable barrier and supporting bone regeneration over an extended period, this resorbable bilayer membrane may address the limitations of the current membranes. Further studies and clinical trials are warranted to validate the efficacy and safety of this drug in humans.

Background and Objectives: Mechanical and biological complications can lead to system fracture or screw loss on dental implants. Narrow and regular platforms have been used without a consensus about the effect of distance the abutment from the prosthetic platform margin. The aim of this study is to evaluate different insertion torques in the deformation of tri-channel platform connections through two- and three-dimensional measurements with micro-CT. Materials and Methods: 164 implants were divided into groups (platform diameter and type): 3.5, 3.75, and 4.3 mm NP (Narrow Platform), and 4.3 mm RP (Regular Platform). Each implant-platform group was then divided into four subgroups (n = 10) with different torques: T45 (45 Ncm), T80 (80 Ncm), T120 (120 Ncm) and T150 (150 Ncm). The implant-abutment-screw assemblies were scanned and the images obtained were analyzed. Results: A significant difference was observed for the linear and volume measures between the different platforms (p &lt;0.01) and the different implant insertion torques (p &lt;0.01). Qualitative analysis suggested higher deformation resistance for the 3.75 NP compared to the 3.5 NP, and RP was more resistant compared to the NP. Conclusions: The 0.25-mm increment in the implant platform did not increase the resistance to the applied insertion torques; the 4.3-mm implant was significantly stronger compared to the 3.5-mm implant and the proposed micro-CT analysis was considered valid for both 2D and 3D analyses of micro gaps, qualitatively and quantitatively.

The objective of this study was to compare the distribution of stress in the maxillary bone, dental implants, and prosthetic components supporting implant-supported maxillary overdentures with partial palatal coverage, in both splinted and unsplinted designs. Two models of maxillary overdentures were designed using the Exocad Dental CAD program, which included cancellous and cortical bone. The complete denture design and abutments (locator abutments in the unsplinted and Hader bar with Vertix attachments placed distally in the splinted variant) were also designed. The denture material was PEEK (Polyetheretherketone), and the method used to analyze patient-specific 3D X-ray scans was 3D QCT/FEA (Three-dimensional Quantitative Computed Tomography-Based Finite Element Analysis). Loading was divided into three load cases: frontal region (both incisors of the denture) and distal region (both molars and first premolar of the denture). The forces applied were 150 N with an oblique component with a buccal inclination of 35° in the frontal region, and 600 N with a buccal inclination of 5° (molars) or solely vertical (premolar) in the distal region. The model with locator abutments showed higher stresses in all load cases in both analyzed implant variants and in the maxilla. The differences in stress distribution between the splinted and unsplinted variants were more significant in the distal region. According to the results of the present study, the amount of stress in bone tissue and dental implant parts was smaller in the splinted, bar-retained variant. The findings of this study can be useful in selecting the appropriate prosthetic design for implant-supported maxillary overdentures with partial palatal coverage.

Keywords: artificial bone; conical implants; cylindrical implants; dental implants; implant stability quotient; insertion torque; polyurethane; post-extraction sites; removal torque.

The early failure of glaucoma surgery is mainly caused by an overly fibrosis at the subconjunctival space causing obliteration of the filtration bleb. Because fibrosis has a suspected basis of genetic predisposition, we have undertaken a prospective study to identify upregulated profibrotic genes in a population of glaucoma patients with signs of conjunctival fibrosis and early postoperative surgical failure. Clinical data of re-operated fibrosis patients, hyperfibrosis patients re-operated more than once in a short time, and control patients with no fibrosis were recorded and analyzed at each follow-up visit. Conjunctival-Tenon surgical specimens were obtained intraoperatively to evaluate the local expression of a panel of genes potentially associated with fibrosis. In order to correlate gene expression signature with protein levels, we quantified secreted proteins in primary cultures of fibroblasts from patients. Expression of VEGF-A, IL-8, C-MYC, and CDKN1A was induced in the conjunctiva of hyperfibrosis patients. VEGF-A and IL-8 protein levels were also increased in fibroblast supernatants. We propose that these proteins may act as biomarkers of conjunctival fibrosis in glaucoma patients undergoing filtering surgery. Molecular markers could be crucial for early detection of patients at high risk of failure of filtration surgery leading to more optimal and personalized treatments.

The XEN® gel stent reduces intraocular pressure (IOP) in glaucoma. XEN®-45 is widely used while the newer XEN®-63 has a larger lumen that may lower IOP more. We retrospectively compared the first 15 XEN®-63 cases to 15 matched XEN®-45 controls. With a preoperative IOP of 18.1 ± 3.9 mmHg (mean ± SD) and a final IOP of 9.2 ± 4.2 mmHg, XEN®-63 implantation resulted in an IOP reduction of 48.0 ± 23.3%. Similarly, with a preoperative IOP of 18.3 ± 4.5 mmHg and a final IOP of 10.5 ± 2.3 mmHg, XEN®-45 implantation resulted in an IOP reduction of 39.5 ± 17.81%. The median follow-up period was 57 days for the XEN®-63 group and 183 days for the XEN®-45 group. 5/15 eyes of each group underwent open conjunctival bleb revision within the period of observation. Two eyes of the XEN®-63 group also had secondary glaucoma surgery. In both groups only one eye required restart of antiglaucomatous medication. XEN®-63 and XEN®-45 effectively lower IOP and medication. XEN-63 achieved lower IOP over a short follow-up. Com-plication and revision rates were similar.

: Glaucoma is the most common cause of blindness, which significantly reduces quality of life. Most glaucoma cases are primary glaucoma; nevertheless, many patients suffer from glaucoma caused by drugs, such as corticosteroids. A comprehensive review of the risks associated with corticosteroid-induced glaucoma is limited. Therefore, we used the Japanese Adverse Drug Event Reporting Database (JADER) published by the Pharmaceuticals and Medical Devices Agency (PMDA) to analyze the risk factors associated with glaucoma and the trends and characteristics of corticosteroid-induced glaucoma. We did not find sex or age differences associated with the onset of glaucoma. Hierarchical clustering and principal component analysis revealed that triamcinolone acetonide and betamethasone sodium phosphate, which are used around the eyes in Japan, are more likely to induce intraocular pressure (IOP) elevation compared with other corticosteroids. Increased IOP is a direct cause of glaucoma. Based on these findings, it may be necessary to limit or avoid the use of these corticosteroids.

(1) Background: Breast cancer-associated lymphedema (BCRL) is a major complication of breast cancer treatment, affects the quality of life of breast cancer survivors who develop it. Manual lymphatic drainage has a beneficial result in combating lymphedema in patients who have undergone breast cancer surgery. The hypothesis consists in complete decongestive therapy reduces the lymphedema at the level of the upper limb on the side of mastectomy. (2) Methods: Twenty-five patients with radical mastectomy and upper limb lymphedema on the mastectomy side were included in this study. Upper limb circumferences were measured with a tape measure at the following levels: metacarpophalangeal joint; distal radioulnar joint; 10 cm distal to lateral epicondyle; 5 cm proximal to elbow joint; 10 cm proximal to lateral epicondyle. (3) Results: Patients received twice weekly manual lymphatic drainage, multi-layer compression bandaging and upper limb muscle stimulation exercises on the mastectomy side twice weekly. The circumference assessed at the level of the metacarpophalangeal joints and distal radio-carpal joint decreased at the final evaluation. Forearm perimetery - 5 and 10 cm distal to the lateral epicondyle the circumference decreased at the final assessment. (4) Conclusions: Patients with breast cancer-related lymphedema should receive comprehensive decongestive therapy in the early stage of lymphedema to achieve rapid clinical results and improved quality of life

This review article deals with the design of bioactive calcium phosphate coatings deposited on metallic substrates to produce bone implants. The bioceramic coating properties are used to create a strong bonding between the bone implants and the surrounding bone tissue. They provide a fast response after implantation and increase the lifespan of the implant in the body environment. The first part of the article describes the different compounds belonging to the calcium phosphate family and their main properties for applications in biomaterials science. The calcium to phosphorus atomic ratio (Ca/P)at. and the solubility (Ks) of these compounds define their behavior in a physiological environment. Hydroxyapatite is the gold standard among calcium phosphate materials, but other chemical compositions/stoichiometries have also been studied for their interesting properties. The second part reviews the most usual deposition processes to produce bioactive calcium phosphate coatings for bone implant applications. Plasma spraying is the main industrial process, but magnetron sputtering, pulsed laser deposition, electrospray deposition, electrophoretic deposition, and electrodeposition are also widely studied in academic and industrial research. The last part describes the main physicochemical properties of calcium phosphate coatings and their impact on the bioactivity of bone implants in a physiological environment.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

Background: The objective of the present study was to evaluate the formation of biofilm in bone patellar tendon bone grafts (BPTB grafts) and to compare it to the formation of biofilm formation in quadrupled hamstring anterior cruciate ligament grafts (4xHt graft). Methods: A descriptive in vitro study was conducted. One 4xHt graft and one BPTB graft were prepared. They were then contaminated with a strain of S. epidermidis. Later, a quantitative analysis was carried out by means of microcalorimetry and sonication with plating. Additionally, a qualitative analysis was carried out by means of electron microscopy. Results: No significant differences were found between the bacterial growth profiles of 4xHt graft and BPTB graft in microcalorimetry and colony counting. In the samples analyzed with electron microscopy, no specific biofilm growth pattern was identified upon comparing BPTB graft to 4xHt graft. Conclusions: There were no significant differences at either the quantitative or qualitative level when comparing bacterial growth in BPTB graft to that in 4xHt graft. Therefore, the presence of sutures in 4xHt graft cannot be established as a predisposing factor for increased biofilm growth in this in vitro study.

Background and Objectives: The novel double-pigtail catheter (DPC) has an additional pigtail coiling at the mid-shaft with centripetal multiple side holes. The aim of the present study was to investigate the advantages and efficacy of DPC in overcoming the complications of conventional single-pigtail catheters (SPC) used to drain pleural effusion. Materials and Methods: Between July 2018 and December 2019, 382 pleural effusion drainage procedures were reviewed retrospectively (DPC, n = 156; SPC without multiple side holes, n = 110; SPC with multiple side holes [SPC+M], n = 116). All patients showed shifting pleural effusion in the decubitus view of chest radiography. All catheters were 10.2 Fr in diameter. One interventional radiologist performed all procedures and used the same anchoring technique. Complications (dysfunctional retraction, complete dislodgement, blockage, and atraumatic pneumothorax) were compared among the catheters using chi-square and Fisher’s exact tests. Clinical success was defined as improvement in pleural effusion within 3 days without additional procedures. A survival analysis was performed for calculating the indwelling time. Results: The dysfunctional retraction rate of DPC was significantly lower than that of the other catheters (p < .001). Complete dislodgement did not occur in any of the DPC cases. The clinical success rate of DPC (90.1%) was the highest. The estimated indwelling times were nine (95% confidence interval [CI]: 7.3–10.7), eight (95% CI: 6.6–9.4), and seven (95% CI: 6.3–7.7) days for SPC, SPC+M, and DPC, respectively, with DPC showing a significant difference (p < .05). Conclusions: DPC had a lower dysfunctional retraction rate compared to conventional drainage catheters. Furthermore, DPC were efficient for pleural effusion drainage with a shorter indwelling time.