Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

Identifying anti-spike antibodies that exhibit strong neutralizing activity against current dominant circulating variants and antibodies that are escaped by these variants have important implications in the development of therapeutic and diagnostic solutions as well as in improving understanding of the humoral response to SARS-CoV-2 infection. We characterized seven anti-RBD monoclonal antibodies for their binding activity, pairing capability and neutralization activity to SARS-CoV-2 and three variant RBDs (UK, SA and BR P.1) via lateral flow immunoassays. The results allowed us to group these antibodies into three distinct epitope bins. Our studies showed that two antibodies had broadly potent neutralizing activity against SARS-CoV-2 and these variant RBDs and that one antibody did not neutralize the SA and BR P.1 RBDs. The antibody escaped by the SA and BR P.1 RBDs retained binding activity to SA and BR P.1 RBDs but was unable to induce neutralization. Further, we demonstrated that the lateral flow immunoassay can be a rapid and effective tool for antibody characterization, including epitope classification and antibody neutralization kinetics. From these studies, the potential contributions of the mutations (N501Y, E484K and K417N/T) contained in these variants’ RBDs on antibody pairing capability, neutralization activity and therapeutic antibody targeting strategy are discussed.

Long span cable-stayed bridge is the main bridge type with a span of more than 400 meters. It is generally designed as a double tower long-span structure with good spanning capacity and economic performance. Wind resistance safety performance is the main index to control the long-span cable-stayed bridge structure. During the operation of long-span cable-stayed bridge structure, because the service life of the cable is far less than the design life of the structure, the wind resistance performance of the structure will inevitably deteriorate significantly, which will seriously affect the structural service performance of symmetric cable-stayed bridge. Based on symmetric reliability theory, this paper takes flutter and static wind stability of long-span cable-stayed bridge structure as the main design control index, uses positive reliability theory to calculate the reliability index of symmetric cable-stayed bridge structure, uses inverse reliability theory to calculate the safety factor of symmetric cable-stayed bridge structure, and evaluates the wind resistant time-varying performance of long-span cable-stayed bridge structure by comprehensively considering the reliability index and safety factor. Taking a practical project of a long-span cable-stayed bridge as a specific case, the wind resistant time-varying reliability of the bridge during its operation for more than 30 years is analyzed, and the parameter sensitivity is analyzed. The results show that the wind resistance performance of the cable-stayed bridge structure is obviously affected by the cable, and the degradation of the cable performance will have an important impact on the wind resistance time-varying performance of the structure, especially the critical wind speed of the structure has obvious time-varying characteristics. The safety factor and reliability index can objectively evaluate the wind resistance time-varying performance of the long-span cable-stayed bridge structure.

The objective of this work was to evaluate the roast time, weight loss and quality of coffee grain at four different roasting degrees, aiming to recognize and develop sustainable patterns to industrialize specialty coffees. Coffee (Coffea arabica L.), from eight producers, with scores between 80 and 83 from SCA classification, were used. Samples of 300 g were roasted in a cylindric rotative roaster, until the grains reached four different roasting profiles (Agtron scale 22.36, #33.64, #40.05, #59.92). Afterwards, analysis of roasting time, gas pressure, weight loss, and sensorial grades were accomplished. It was observed that samples roasted at #22.36 led to significant differences, regarding roasting time and weight loss. Furthermore, there is a significant difference at the sensorial grades of the coffee beverage. Comparing the roast degree #40.05 (standard used for specialty coffee) with the roast degree #22.36 (most used for commodities coffee), the first one has a gas consumption of 0.34 kg per coffee kg, whilst the second presented a gas consumption of 0.41 kg per coffee kg. Thus, from gas consumption, roast degree # 40.05 is the more sustainable option, along with the remaining parameters analyzed.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

Over the past decades, overweight and obesity has become a global epidemic and the leading threat for death. To prevent the serious risk, an overweight or obese individual must apply a long-term weight-management strategy to control food intake and physical activities, which is however, not easy. Recently, with the advances of information technology, more and more people can use wearable devices and smartphones to obtain physical activity information, while they can also access various health-related information from Internet online social networks (OSNs). Nevertheless, there is a lack of an integrated approach that can combine these two methods in an efficient way. In this paper, we address this issue and propose a novel mobile-social framework for health recognition and recommendation, namely, H-Rec². The main ideas of H-Rec² include (1) to recognize the individual's health status using smartphone as a general platform, and (2) to recommend physical activity and food intake based on personal health information, life science principles, and health-related information obtained from OSNs. To demonstrate the potentials of the H-Rec² framework, we develop a prototype that consists of four important components: (1) an activity recognition module that senses physical activity using accelerometer, (2) a health status modeling module that applies a novel algorithm to generate personalized health status index, (3) a restaurant information collection module that collects relevant information from OSN, and (4) a restaurant recommendation module that provides personalized and context-aware recommendation. To evaluate the prototype, we conduct both objective and subjective experiments, which confirm the performance and effectiveness of the proposed system.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

Setting A high proportion of notified tuberculosis cases in the Philippines are clinically diagnosed (63%) as opposed to bacteriologically confirmed. Better understanding of this phenomenon is required to improve tuberculosis control. Objectives To determine the percentage of Smear Negative Presumptive Tuberculosis patients that would be diagnosed by GeneXpert; compare clinical characteristics of patients diagnosed as tuberculosis cases; and review the impact that the current single government physician and a reconstituted Tuberculosis Diagnostic committee (Expert Panel) may have on tuberculosis over-diagnosis. Design This is a cross-sectional study of 152 patients 15-85 years old with two negative Direct Sputum Smear Microscopy results, with abnormal chest X-ray who underwent GeneXpert testing and review by an Expert Panel. Results 31% (48/152) of the sample were Xpert positive. 93% (97/104) of GeneXpert negatives were clinically diagnosed by a Single Physician. Typical symptoms and X-ray findings were higher in bacteriologically confirmed tuberculosis. When compared to GeneXpert results, the Expert panel’s sensitivity for active tuberculosis was high (97.5%, 39/40) but specificity was low (40.2%, 35/87). Conclusion Using the GeneXpert would increase the level of bacteriologically confirmed tuberculosis substantially among presumptive Tuberculosis. An Expert panel will greatly reduce over-diagnosis usually seen when a decision is made by a Single Physician.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

This paper considers the Hermitian solutions of a new system of commutative quaternion matrix equations, we establish both necessary and sufficient conditions for the existence of solutions. Furthermore, we derive an explicit general expression when it is solvable. To illustrate our main findings, we present two numerical algorithms and examples in this paper.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

Prostate cancer is the second most frequent malignancy (after lung cancer) in men worldwide. Prostate tissue biopsies are usually graded using scores according to the Gleason grading system. This Gleason score is the most popular prognostic marker that reveals the potential aggressiveness of the disease. However, inter-observer variability in rating by human assessors is a major limiting factor. Such variability could lead to missing a severe case or suggesting unnecessary treatments. This study explores the discriminative ability of artificial intelligence (deep learning models) for Gleason score assessment. The study was designed to use whole-slide images of digitized H&E-stained biopsies of prostate tissues to automate the grading process and provide a remotely accessible clinical decision support system. Custom convolutional neural network architectures were trained on 10,616 images of prostate tissues. Gaussian filters were applied to pre-process the images and improve model performance. Transfer learning was applied to train eight machine learning architectures namely: Xception, VGG16 & 19, ResNet101, MobileNet, DenseNet121, EfficientNetB5 & B7. Efficient NetB7 had the best performance 85.2% compared with ground-truth classification by experts. Performance improves as more data is available. The model was deployed and hosted as a web application API on Google cloud service to ensure remote access. Tissue biopsy images can be uploaded and the corresponding Gleason score recovered immediately. This system reduces diagnostics turnaround time, increase throughput, and compensate for limited skills, especially in low resource settings.

In recent years, the implementation of artificial intelligence (AI) in accounting has grown in many domains, including auditing. AI permits auditors to evaluate large data sets and rapidly identify discrepancies and sequences in audit. This means auditors can review all of a client's transactions via a low time and effort. This entails auditing firms investing heavily in technological infrastructure as well as training their human resources to use cutting-edge AI technologies. Thus, this research sought to investigate the impact of the use of AI techniques by Jordanian external auditors in fraud risk assessment, the moderating effect of auditor size. The descriptive analytical method was used by distributing 280 questionnaires electronically to auditors employed in auditing firms operating in Jordan, The result reveals that AI techniques are extremely beneficial in fraud risk assessment at all levels, and the relationship between the use of AI techniques and the assessment of fraud risk has improved as auditor size has increased.

In order to comprehensively evaluate the employee satisfaction of mine occupational health and safety management system, an analytic method based on fuzzy analytic hierarchy process and 2- tuple linguistic model was established. Firstly, based on the establishment of 5 first- grade indicators and 20 second- grade ones, the weight of each indicator is calculated and validated by method of FAHP and root mean square model. Secondly, a path based on the time-ordered Weighted Averaging Operator (T-OWA) model is constructed. Finally, the model is validated by empirical analysis. The results demonstrate that the employee satisfaction of the mine occupational health and safety management system is of the “general” rank. The method including the comprehensive evaluation of employee satisfaction and the quantitative analysis of language evaluation information ensures the authenticity of the language evaluation information.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

For many engineering applications it is sufficient to use the concept of simple materials. However, higher gradients of the kinematic variables are taken into account to model materials with internal length scales as well as to describe localization effects using gradient theories in finite plasticity or fluid mechanics. In many approaches length scale parameter have been introduced that are related to a specific micro structure. An alternative approach is possible, if a thermodynamically consistent framework is used for material modelling as shown in the present contribution. However, even if sophisticated and thermodynamically consistent material models can be established there are still not yet standard experiments to determine higher order material constants. In order to contribute to this ongoing discussion system identification based on the method of self-adaptive filtering is proposed in this paper. To evaluate the effectiveness of this approach it has been applied to second-order gradient materials considering longitudinal vibrations. Based on thermodynamically consistent models that have been solved numerically it has been possible to prove that system identification based on self-adaptive filtering can be used effectively for both narrow-band and broadband signals in the field of second-order gradient materials. It has also been found that the differences identified for simple materials and gradient materials allow for condition monitoring and detection of gradient effects in the material behavior.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Gamba grass (Andropogon gayanus Kunth) is a tussock-forming forage species adapted to acid soils of Brazilian savannas and cultivated for grazing pastures. Four decades since its releasing, Planaltina prevails as the most commercialized cultivar of the species, even though the new cultivar BRS Sarandi could be a better alternative for Gamba grass-based farms by presenting greater leaf:stem ratio. The objective of this study was to evaluate the average daily live weight gain (ADG) of Nellore bulls (Bos indicus) for two Gamba grass cultivars – Planaltina and Sarandi. The experiment was conducted in Planaltina, Federal District, Brazil, during 3 years, namely 2018, 2018-2019 and 2020. The experimental design was completely randomized block with two treatments and three replicates, each one continuously stocked at three stocking rates (SR) - 1.3, 2.6 and 4 young bulls/ha. Canopy height (CH), forage mass (FM), plant-part proportion (leaf, stem and dead material) and nutritive value were evaluated. In 2018, mean ADG for Sarandi pastures was greater (0.690 kg/bull/d) than Planaltina (0.490 kg/bull/d) (P=0.0839). In the subsequent year (2018-2019), there was no effect of cultivar (P = 0.4089), while in 2020 the ADG was again affected by cultivar (P=0.0412), confirming the advantage of Sarandi (0.790 kg/bull/d) over Planaltina (0.650 kg/bull/d). In 2018 and 2020, the percentage of stems for Sarandi was about 3-6 pp lesser than for Planaltina (P

Here, we present a staged approach for an innovative repurposing of a portable infant humidicrib into a live cell growth, observation, and imaging system. Furthmore, humidicrib can support different variations of “umbilical” bioreactors, and can be used to conduct electrophysiology experiments and in situ immunohistochemistry. Modifications incorporate a closed loop carbon dioxide (CO₂) concentration control system with umbilical CO₂ and heating support for tailored bioreactors. The repurposing cost is inexpensive and allows for the continued observation and imaging of cells. This prototype unit has been used to continuously observe and image live primary neurons for up to 21 days. This demonstrates the repurposed units’ suitability for use in tissue culture based research, particularly where modifications to microscopes are required or where sensitive manipulation outside of a standard incubator is needed.

Research on Traffic Light Recognition (TLR) has grown in recent years, primarily driven by the growing interest in autonomous vehicles development. Machine Learning algorithms have been widely used to that purpose. Mainstream approaches, however, require large amount of data to properly work, and as a consequence, a lot of computational resources. In this paper we propose the use of Expert Instruction (IE) as a mechanism to reduce the amount of data required to provide accurate ML models for TLR. Given an image of the exterior scene taken from the inside of the vehicle, we stand the hypothesis that the picture of a traffic light is more likely to appear in the central and upper regions of the image. Frequency Maps of traffic light location were thus constructed to confirm this hypothesis. The frequency maps are the result of a manual effort of human experts in annotating each image with the coordinates of the region where the traffic light appears. Results show that EI increased the accuracy obtained by the classification algorithm in two different image datasets by at least 15%. Evaluation rates achieved by the inclusion of EI were also higher in further experiments, including traffic light detection followed by classification by the trained algorithm. The inclusion of EI in the PCANet achieved a precision of 83% and recall of 73% against 75.3% and 51.1%, respectively, of its counterpart. We finally presents a prototype of a TLR Device with that expert model embedded to assist drivers. The TLR uses a smartphone as a camera and processing unit. To show the feasibility of the apparatus, a dataset was obtained in real time usage and tested in an Adaptive Background Suppression Filter (AdaBSF) and Support Vector Machines (SVMs) algorithm to detect and recognize traffic lights. Results show precision of 100% and recall of 65%.

Spatio-temporal aspects of data lead to critical information. Sensors capture data at all scales continually so it is imperative that useful information be extracted ubiquitously and regularly. Location plays a vital part by helping understand relations between datasets. It is crucial to link developmental works with spatial attributes and current challenge is to create an open platform that manages real-time sensor data and provides critical spatial analytics atop expert domain knowledge provided in the system. That is a two-faced problem where the solution tackles not only data from multiple sources but also runs data management platform, a spatial data infrastructure(SDI) as backbone framework able to harness sensor web(SW). The paper proposes development of such a globally shared open spatial expert system(ES), SmaCiSENS, a first of a kind geo-enabled knowledge based(KB) ES for multiple fields, smarter cities to climate modeling. SmaCiSENS is integration of SW and SDI with domain KB on data and problems, ready to infer solutions. The paper describes an architecture for semantic enablement for SW, SDI; connect interfaces, functions of SDI and SW, and sensor data application program interfaces (APIs) to better manage climate modeling, geohazard, global changes, and other vital areas of attention and action.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

Hypertension is a frequent risk factor for cardiovascular diseases and the prevalence rate is continuously rising. Multiple pathophysiological mechanisms are responsible for hypertension, necessitating a combination of drugs from different classes for best management. Combination therapy is five times more effective in decreasing blood pressure compared to escalating the dose of a single agent. As per the ACCOMPLISH trial analysis, coupling a renin-angiotensin system inhibitor with a calcium channel blocker is more effective than the combination of a renin-angiotensin system inhibitor with diuretics in reducing major cardiovascular events, cardiovascular-related mortality, and the progression of chronic kidney disease. The renin-angiotensin system can be suppressed by inhibiting the angiotensin-converting enzyme or angiotensin type 1 receptor (AT1R), resulting, in decreased vascular smooth muscle contraction, heart performance, and reduced aldosterone synthesis. Calcium channel blockers work by inhibiting L-type calcium channels, reducing heart performance via negative inotropic, chronotropic, and bathmotropic effects, along with reducing vascular smooth muscle contraction. Diuretics exert their antihypertensive impact by changing body fluid volume and electrolytes. Initially, hypertension treatment commences with a single medication but often, different classes of two or more antihypertensive medications are necessary for achieving the target blood pressure goal. Sometimes, for Resistant hypertension four different classes of antihypertensive medications are necessary to reach the target blood pressure goal.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

The purpose of the study is to control the ratio of programs of different genres when forming the broadcast grid in order to increase and maintain the rating of the channel. In the multichannel environment, television rating control consists of selecting such content, ratings of which are completely restored after advertising. A hybrid approach combining the benefits of semantic training and fuzzy relational equations in simplification of the expert recommendation systems construction is proposed. The problem of retaining the television rating can be attributed to the problems of fuzzy resources control. The increase or decrease trends of the demand and supply are described by primary fuzzy relations. The rule-based solutions of fuzzy relational equations connect significance measures of the primary fuzzy terms. Rules refinement by solving fuzzy relational equations allows avoiding labor-intensive procedures for the generation and selection of expert rules. The solution set generation corresponds to the granulation of the television time, where each solution represents the time slot and the granulated rating of the content. In automated media planning, generation of the weekly TV program in the form of the granular solutions provides the decrease of the time needed for the programming of the channel broadcast grid.

Antler is the fastest growing tissue. Because is based on proto-oncogenes, to avoid the risk of cancer, antlers evolved strong anticancer mechanisms, and thus its extract (DVA) is effective also against the few human tumours studied so far. We assessed whether DVA is a general anticancer compound testing direct effects in cells of different tumours: glioblastoma (GBM), colorectal and breast cancer, and leukaemia. DVA reduced viability of tumour but not healthy cells. Mobility decreased at least at the longest test (72 h). Intraperitoneal/oral 200 mg DVA/kg administration in GBM xenograft mice for 28 d reduced tumour weight 66.3% and 61.4% respectively, and also spleen weight. In addition, tumours treated with DVA showed symptoms of liquefactive necrosis. Serum cytokines showed DVA up-regulated factors related with tumour fighting and down-regulated those related with inducing immune tolerance to the tumour. DVA shows general anticancer effects in the lines tested and, in GBM mice, also strong indirect effects apparently mediated by the immune system.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

There has been an increased focus on new technologies to monitor habitat use and behaviour of cattle, to develop a more sustainable livestock grazing system, without compromising animal welfare. The currently most used method for monitoring cattle behaviour is tri-axial accelerometer data from systems such as virtual fencing technology or bespoke monitoring technology. This method requires high frequency data, and as such, quickly drains contemporary systems of power making it unsuitable for long-term monitoring. In this paper, we explore the possibility of determining habitat preference and habitat utilisation patterns in cattle, using low frequency activity and location data. We do this by (1) calculating habitat selection ratios, (2) determining daily activity patterns and based on those, (3) inferring grazing and resting sites in a group of cattle wearing virtual fencing collars in a coastal setting with grey, wooded and decalcified dunes, humid dune slacks and salt meadows. We found that GPS data, and a measure of activity, combined with accurate mapping of habitats can be an effective tool in assessing habitat preference. The animals preferred salt meadows over the other habitats, with wooded dunes and humid dune slacks being the least preferred. We were able to identify daily patterns in activity. By comparing general trends in activity levels to existing literature, it was possible to somewhat infer resting and grazing behaviour in the different habitats. According to our inference of behaviour the herd predominantly used the salt meadows for resting and ruminating. The approach used in this study allowed us to use GPS location data for measuring the activity and combine it with accurate habitat mapping in a cheap and effective way, which can be an important tool for guiding management decisions.

Spatial planners are nowadays strongly interested in the benefits of greenspace for the health of urban residents. However, concrete and context-specific guidance on effective greening strategies is still lacking. We present a novel, model-based approach to support the development of such strategies. The approach is quantitative and spatially-explicit, and accounts for multiple health benefits as well as burdens. In this study, we applied the approach to the city of Maastricht (The Netherlands), and conducted an integrated, city-scale assessment of the health benefits and burdens of four urban greenspace designs. These included: ‘No greenspace’, ‘Current greenspace’, ‘Green parking lots and squares’, and ‘Optimized greenspace locations’. For each greenspace design, indicator values were calculated for five health determinants: heat stress, air pollution, perceived unsafety, unattractive views, and tick-bite risk. To assess the health contribution of urban greenspace in a given design, these indicator values were compared with the values in the ‘No greenspace’ design. The study produced clear, quantitative conclusions about the health benefits and burdens of the urban greenspace designs for the case of Maastricht, but also generated novel, more general insights relevant to planning of urban greenspace for health. These insights concern the importance of translating health policy objectives into specific target values or thresholds, and the importance of ‘smart’ choices in greenspace type and location that can effectively reduce trade-offs between health benefits and burdens. Priorities for future research, addressing limitations of the presented approach, concern a further expansion of the range of health benefits and burdens covered by the model, and the development of a common metric for the entire range of health benefits and burdens allowing optimization of greenspace design to maximize its overall net health benefit.

This paper explores Ghana's two-decade journey in developing a digital land information system (LIS), exemplified by Ghana Enterprise Land Information System (GELIS) and Enterprise Land Information System (ELIS). Despite advancements by Ghana’s Lands Commission, manual processes persist and coexist with digital ones. Our study uses a qualitative approach to assess the effectiveness of the LIS implemented in Accra. The study found that Accra’s LIS is highly aligned with clear institutional mandates, roles, and responsibilities as well as the availability of laws and policies to support analogue to digital conversion. Furthermore, a robust approach for protecting data, operating system and software underpins the system. Subsequently, the integration of a digital LIS has enhanced service delivery and accountability. Nonetheless, Accra’s LIS is still at the beginning of a comprehensive learning and development curve. To sustain the LIS requires furtherance in the implementation plan, funding, law implementation, ICT strategy, divisional integration, work processes, data quality, and communication strategy. These findings will inform the next steps of improvement for Accra's LIS and guide its nationwide scaling, contributing to discussions on technology acceptance dynamics in predominantly analogue environments.

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

Background: clubfoot is a common congenital deformity. The Ponseti technique, involving early corrective manipulations followed by the application of long leg casts and Achilles tenotomy, is widely accepted as the preferred treatment. Rapid healing of the tendon after surgery has been documented, but the aspect regarding tendon structure and properties is not known. Three cases of Achilles tendon rupture in adolescent previously treated for clubfoot have been described in the literature. Since rupture is a rare event in this age group a possible correlation with previous surgery has been hypothesized. The primary aim of the study was to compare the ultrasound findings of the Achilles tendon, in patients treated for clubfoot, between patients treated with casting alone and the ones who underwent surgery (percutaneous tenotomy or Z-plasty lengthening). Methods: 22 asymptomatic patients, (34 feet) median age 12 years, previously treated for clubfoot, were recruited for this study; the patients underwent an Achilles tendon ultrasound examination during a follow-up outpatient visit. Results: a greater thickness and structural alterations with presence of hypoechoic areas of the operated tendons compared to those treated with plaster alone were observed (p value: 0.0498 and

Contemporary financial systems, despite their inherent complexity and resilience, face significant challenges related to transparency, efficiency, and security. Notable deficiencies in transparency and emerging security vulnerabilities underscore the pressing need for innovative solutions in current financial practices. Hence, this paper introduces a financial distribution system based on a consortium blockchain. Given organizations’ preference for keeping sensitive data private, the partially decentralized nature of consortium blockchains plays a pivotal role in the proposed system’s architecture. Moreover, within this system, the proposed smart contract serves a dual role. It functions not only as a transactional tool but also as a specialized solution designed to improve transactional procedures. Its multifaceted capabilities include ensuring data accuracy, facilitating swift execution, and ensuring adherence to regulatory requirements within the dynamic financial distribution landscape. Through rigorous testing and empirical analysis utilizing the Hyperledger Besu platform, it has been observed that the performance of the proposed system surpasses traditional blockchain frameworks. The results unequivocally demonstrate the proposed system’s proficiency in handling high-frequency financial transactions with minimal computational burden.

Various vaccines have been developed in response to the SARS-CoV-2 pandemic, and the safety of vaccines has become an important issue. COVID-19 vaccines-related central nervous system inflammatory demyelinating diseases (CNS IDDs) have been reported recently. We present one case of AstraZeneca vaccine-related myelin oligodendrocyte glycoprotein (MOG) antibody-associated disease and literature review another 78 patients published from January 2020 to October 2022. Patients were divided into three vaccine groups (viral vector, mRNA and inactivated vaccines) for further analyses. Among 79 patients with COVID-19 vaccines-related CNS IDDs, 49 (62%) cases received viral vector vaccines, 20 (25.3%) received mRNA vaccines and 10 (12.7%) received inactivated vaccines. Twenty-seven cases (34.2%) were confirmed with autoantibodies, including 15 patients (19%) with anti-MOG, 11 (13.9%) with anti-aquaporin 4 (AQP4), and one (1.3%) with both antibodies. Significantly, more males developed CNS IDDs post viral vector vaccines compared to mRNA and inactivated vaccines. Patients receiving mRNA vaccines were older than other groups. Furthermore, mRNA and inactivated vaccines correlated more with anti-AQP4 antibodies, while viral vector vaccines showed higher MOG positivity. The research suggests potential associations between COVID-19 vaccines-related CNS IDDs and gender, age, and autoantibodies, contingent on vaccine types. Protein sequence analysis implies similarities between the S protein and AQP4/MOG. Further studies may elucidate the mechanisms of CNS IDDs, aiding vaccine selection for specific groups.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

This study aimed to investigate the relationship between sleep duration, dementia severity, age, and ANS regulation. This cross-sectional pilot study included 27 older patients with probable Alzheimer’s disease, hospitalized at a psychiatric center. We measured heart rate variability to assess ANS regulation at night, evaluated dementia severity using the Clinical Dementia Rating scale, and obtained sleep duration data from sleep diaries maintained by psychiatric nurses. The data were analyzed using repeated-measures generalized linear models with age, sex, dementia severity, and medication (antipsychotics) as covariates. A sleep duration of 7–8 h per night was associated with better ANS regulation than other sleep durations, as indicated by sympathovagal balance (p = 0.005). ANS dysregulation was characterized by a 20.7% increase in sympathetic nervous system activity and a 14.8% decrease in parasympathetic nervous system (PSNS) activity. We found a significant correlation between dementia severity and PSNS activity (p = 0.04) and observed an inverted U-shaped association between sleep duration and ANS regulation. This pilot study demonstrated that a sleep duration of 7–8 h per night may be critical in maintaining optimal ANS regulation. Bidirectional associations between sleep duration, inadequate sleep duration, aging, and ANS regulation warrant further investigation.

The ongoing challenge to ensure a sustainable and affordable energy supply forces industrial companies to implement appropriate measures. These measures typically lead to an increased system complexity, which has to be addressed during operation. Whereas existing approaches from the field of supervisory and optimal control appear to be capable of mastering this issue, these are still not adopted in industry. Therefore, this work presents a procedure model for the systematic development of application-oriented operating strategies for industrial energy supply systems. The procedure model combines research approaches from the fields of sequencing control and approximate MPC to extract rule-based operating strategies. By splitting the procedure model into five phases, expert knowledge can be integrated in a target-oriented manner. Subsequently to the description, the procedure model is exemplary applied to the example of an industrial heating supply system. Throughout an optimization study, the developed operating strategy is compared to a MPC strategy as well as a baseline strategy. Whereas the conventional MPC approach is the upper bound with regard to optimality, the developed operating strategy is able to generate comparable results. Compared to the baseline strategy, a relative reduction in operating expenses of 5.4 % to 37.0 % are achieved in this specific use case.

Transport infrastructure’s asphalt pavement deteriorates under the influence of destructive factors. Damages which have been occurred during its exploitation period are repaired, and when their further rehabilitation is economically and technically irrational, the asphalt pavement is recycled. The material from the asphalt pavement layer that has reached its limit state is milled out or broken and crushed and then is repeatedly used in the production of hot-mix asphalt (HMA) or warm-mix asphalt (WMA) mixtures. In this paper, the dynamics of the percentage recycling ratio (RR) of old asphalt pavement material was investigated. RR represents the quantity of reclaimed asphalt pavement (RAP) used in the production of HMA and WMA mixtures in Europe and the USA, divided by the total amount of RAP prepared in the country. Factors and goals affecting it are analyzed. An original system of 10 criteria that increase the RR country has been created. By applying different multiple criteria decision making (MCDM) methods and using the importance given to these criteria by 14 experts, the normalized subjective weights of the criteria were determined. Analytic Hierarchy Process (AHP), rank correlation, Average Rank Transformation into Weight - Linear (ARTIW-L) and Non-linear (ARTIW-N), Direct Percentage Weight (DPW) methods were used in the study. The results display that the RAP recycle rate is close to 100% in countries with a sustainable economic background. In the Baltic countries, it is mostly increased by the adequacy of regulatory documents, the strategy promoting asphalt recycling in the country, and the homogeneity and classifying of RAP. The number and capacity of RAP stocks, the number and productivity of asphalt milling equipment and the wear and tear of the asphalt pavement have the least influence on the increase of RR. The opinions of experts in assessing the significance of all criteria are consistent. The averages of the weights of criteria determined by four MCDM methods (AHP, ARTIW-L, ARTIW-N, DPW) made it possible to obtain more reliable results. These results can be used to make strategic decisions and to create a plan of practical actions to increase the RAP recycling rate in the developing countries.

This paper proposes a method for determining the bridge condition index (BCI) in concrete bridges, which is based on the views of bridge experts. First, eight indices were defined for a concrete bridge including structure, hydrology, safety, load impact, geotechnical and seismicity, strategic importance, facilities, and finally traffic and pavement. Each index consists of several sub-indices. Next, a series of questionnaires about the relative importance of indices and their sub-indices were prepared and distributed among bridge experts. Experts’ views were analyzed by Expert Choice software and the relative importance (weight) of each index and each sub-index was determined using the analytical hierarchy process (AHP). Then, based on experts’ views, an average score was assigned to each sub-index for any condition. Now the bridge inspectors can examine the bridge and determine the scores of sub-indices. Each index’s score is the sum of the weighted score assigned to its’ sub-indices and BCI is the sum of weighted scores assigned to indices. Higher values of BCI indicate a better condition. Therefore, bridges with lower BCI take priority in maintenance activities. To apply the proposed method, five bridges were selected in Semnan province, Iran, and BCI calculation of these bridges were conducted.

Opossums, native to the Americas, are unique marsupials with over 100 species. The Common Opossum and Virginia Opossum are notable species. They are nocturnal, omnivorous, and adapt to various habitats. Their reproduction involves a short gestation and marsupial pouch development. Despite their ecological benefits like seed dispersal and insect control, their proximity to human habitats exposes them to pathogens, posing public health risks. These include protozoa, helminths, and arthropods that can spread zoonotic parasites and vector-borne diseases. The marsupial immune system, including opossums, is complex, rivaling eutherian mammals. Key immune genes were identified in the grey short-tailed opossum genome. CD1 protein and VpreB surrogate light chain were also found. Marsupials are proposed as ideal models for studying developmental immunology. A West Indian opossum (Didelphis marsupialis) was found and examined. Blood tests revealed abnormalities, including a low white blood cell count and signs of anemia. The results contribute to understanding the species’ health and adaptability in the wild.

Artificial intelligence (AI) techniques have grown rapidly in recent years in the context of computing with smart mobile phones that typically allows the devices to function in an intelligent manner. Popular AI techniques include machine learning and deep learning methods, natural language processing, as well as knowledge representation and expert systems, can be used to make the target mobile applications intelligent and more effective. In this paper, we present a comprehensive view on mobile data science and intelligent apps in terms of concepts and AI-based modeling that can be used to design and develop intelligent mobile applications for the betterment of human life in their diverse day-to-day situation. This study also includes the concepts and insights of various AI-powered intelligent apps in several application domains, ranging from personalized recommendation to healthcare services, including COVID-19 pandemic management in recent days. Finally, we highlight several research issues and future directions relevant to our analysis in the area of mobile data science and intelligent apps. Overall, this paper aims to serve as a reference point and guidelines for the mobile application developers as well as the researchers in this domain, particularly from the technical point of view.

Increased nutrient withdrawal by rapidly expanding intensive cropping systems, in combination with imbalanced fertilization, is leading to potassium (K) depletion from agricultural soils in Asia. There is an urgent need to better understand the soil K-supplying capacity and K-use efficiency of crops to address this issue. Maize is increasingly being grown in rice-based systems in South Asia, particularly in Bangladesh and North East India. The high nutrient extraction, especially K, however, causes concerns for the sustainability of maize production systems in the region. The present study was designed to estimate, through a plant-based method, the magnitude, and variation in K-supplying capacity of a range of soils from the maize-growing areas and the K-use efficiency of maize in Bangladesh. Eighteen diverse soils were collected from several upazillas (or sub-districts) under 11 agro-ecological zones to examine their K-supplying capacity from the soil reserves and from K fertilization (@ 100 mg K kg-1 soil) for successive seven maize crops grown up to V10-V12 in pots inside a net house. A validation field experiment was conducted with five levels of K (0, 40, 80, 120 and 160 kg ha-1) and two fertilizer recommendations based on “Nutrient Expert for Maize-NEM” and “Maize Crop Manager-MCM” decision support tools (DSSs) in 12 farmers’ fields in Rangpur, Rajshahi and Comilla districts in Bangladesh. Grain yield and yield attributes of maize responded significantly (P < 0.001) to K fertilizer, with grain yield increase from 18 to 79% over control in all locations. Total K uptake by plants not receiving K fertilizer, considered as potential K-supplying capacity of the soil in the pot experiment, followed the order: Modhukhali >Mithapukur >Rangpur Sadar >Dinajpur Sadar >Jhinaidah Sadar >Gangachara >Binerpota >Tarash >Gopalpur >Daudkandi >Paba >Modhupur >Nawabganj Sadar >Shibganj >Birganj >Godagari >Barura >Durgapur. Likewise in the validation field experiment, the K-supplying capacity of soils was 83.5, 60.5 and 57.2 kg ha-1 in Rangpur, Rajshahi, and Comilla, respectively. Further, the order of K-supplying capacity for three sites was similar to the results from pot study confirming the applicability of results to other soils and maize-growing areas in Bangladesh and similar soils and areas across South Asia. Based on the results from pot and field experiments, we conclude that the site-specific K management using the fertilizer DSSs can be the better and more efficient K management strategy for maize.

Viruses can induce the fusion of infected and neighboring cells, leading to the formation of syncytia. Cell-cell fusion is mediated by viral fusion proteins on the plasma membrane of infected cells that interact with cellular receptors on neighboring cells. Viruses use this mechanism to spread rapidly to adjacent cells or escape host immunity. For some viruses, syncytium formation is a hallmark of infection and a known pathogenicity factor. For others, the role of syncytium formation in viral dissemination and pathogenicity remains poorly understood. Human cytomegalovirus (HCMV) is an important cause of morbidity and mortality in transplant patients and the leading cause of congenital infections. Clinical HCMV isolates have broad cell tropism but differ in their ability to induce cell-cell fusions, and little is known about the molecular determinants. We developed a system to analyze HCMV glycoprotein B (gB) variants in a defined genetic background. HCMV strains TB40/E and TR were used as vectors to compare the fusogenicity of six gB variants from congenitally infected fetuses with those from three laboratory strains. Five of them conferred the ability to induce fusion of MRC-5 human embryonic lung fibroblasts to one or both backbone strains, as determined by a split GFP-luciferase reporter system. The same gB variants were not sufficient to induce syncytia in infected ARPE-19 epithelial cells, suggesting that additional factors are involved. The system described here allows a systematic comparison of the fusogenicity of viral envelope glycoproteins and may help to clarify whether fusion-promoting variants are associated with increased pathogenicity.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

A model of a single-server queuing-inventory system (QIS) with catastrophes and a finite waiting room for consumer customers (c-customers) has been developed. When a catastrophe occurs, all inventory in the system's warehouse is destroyed, but c-customers in the system are still waiting for restocking. In addition to c-customers, negative customers (n-customers) are also taken into account, which displaces one c-customers (if any). The policy (?, ?) is used to replenish stocks. If upon arrival of the c-customer the inventory level is zero, then according to Bernoulli’s scheme this c-customer is either lost or joining the queue. The mathematical model of the studied QIS is constructed in the form of a two-dimensional continuous-time Markov chain (2D CTMC). Exact and approximate methods for calculating the steady-state probabilities of constructed 2D CTMCs are developed and closed-form expressions are derived for calculating the performance measures. The results of numerical experiments are presented, demonstrating the high accuracy of the developed approximate formulas, as well as the behavior of performance indicators depending on the reorder point. In addition, an optimization problem is solved to obtain the optimal reorder point to minimize the expected total cost.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

This study delves into the realm of heuristic evaluation within usability testing, focusing on refining and applying a tailored algorithm that simplifies the implementation of the Analytic Hierarchy Process for heuristic prioritization. Addressing the prevalent challenge of disparate evaluation methodologies and the absence of a standardized process in usability testing, our research introduces a novel method that leverages the Analytic Hierarchy Process alongside a bespoke algorithm. This algorithm utilizes transitive properties for pairwise comparisons, significantly reducing the evaluative workload. This innovative approach facilitates the estimation of heuristic relevance irrespective of the number of items per heuristic or the item scale and streamlines the overall evaluation process. In addition to rigorous simulation testing of the tailored algorithm, we applied our method in a practical scenario, engaging seven usability experts in evaluating a web interface. This empirical application underscored our method’s capacity to diminish the requisite comparison count and spotlight areas of improvement for critically weighted yet underperforming heuristics. The outcomes of this study underscore the efficacy of our approach in enhancing the efficiency and organization of heuristic evaluations, paving the way for more structured and effective usability testing methodologies in future research endeavors.

The COVID-19 led to changes modifying the role of digital transformation and unleashing unparalleled opportunities to improve business production processes in all three dimensions of sustainability - economic, social, and environmental through data-driven innovative service implications that significantly impact restaurant business, resulting in an increased competitive advantage. This paper identifies the innovative service implications and summarizes sustainable social systems measures in the context of strategic management in the restaurant industry triggered by COVID-19. Based on in-depth interviews with sixteen key experts in the restaurant industry, the paper clarifies and concretizes the rapidly transforming problem of identifying the main changes in the restaurant business, using three dimensions: consumer demand, corporate strategy optimization, and the use of the company's innovative potential. The findings reveal how companies need to expand their digital strategies and adapt their management approach to all stakeholders bringing sustainable business development in the post-pandemic period into focus. This paper serves as a framework for understanding the digital transformation role in resilient business management within restaurant social systems, with friction occurring along the workflow from kitchen to customer.

The delineation of the clinical target volumes (CTVs) for radiation therapy is time-consuming, requires intensive training and shows high inter-observer variability. Supervised deep learning methods depend heavily on consistent training data, thus state-of-the-art research focuses on making CTV labels more homogeneous and strictly bounding them to current standards. International consensus expert guidelines standardize CTV delineation by conditioning the extension of the clinical target volume on surrounding anatomical structures. Training strategies that directly following the construction rules given in the expert guidelines or the possibility to quantify the conformance of manually drawn contours with the guidelines are still missing. 71 anatomical structures that are relevant for CTV delineation in head and neck cancer patients according to the expert guidelines were segmented on 104 CT scans to assess the possibility to automate their segmentation by state-of-the-art deep learning methods. nnU-Net models were trained to automatically segment those 71 structures on planning CT scans. We report the DICE, HD and sDICE for 71 + 5 anatomical structures for most of which no previous segmentation accuracies have been reported. For those structures, for that prediction values have been reported, our segmentation accuracy matched or exceeded the reported values. The predictions from our models were always better than those predicted by the TotalSegmentator. The sDICE with 2mm margin was larger than 80% for almost all structures. Individual structures with decreased segmentation accuracy are analyzed and discussed with respect to their impact on the CTV delineation following the expert guidelines. No deviation is expected to affect the rule-based automation of the CTV delineation.

Warming of the climate system is unequivocal, and many of the observed changes are unprecedented over five decades to millennia. Globally the atmosphere and ocean is increasingly getting warmer, the amount of ice on the earth is decreasing over the oceans, and the sea level has risen. According to Intergovernmental Panel on Climate Change, the total increasing temperature globally averaged combined land and surface between the average of the 1850-1900 period and the 2003 to 2012 period is 0.78 °C (0.72 to 0.85). But should we prepare for such the relatively small change? The importance is not the mean of the warming but the considerable likelihood of climate change that could trigger extreme natural hazards. The impact and the risk of climate change associated with railway infrastructure have not been fully addressed in the literature due to the difference in local environmental parameters. On the other hand, the current railway network in Malaysia, over the last decade, has been significantly affected by severe weather conditions such as rainfall, lightning, wind and very high temperatures. Our research findings point out the extremes that can lead to asset system failure, degraded operation and ultimately, delays to train services. During the period of flood, the embankment of the track can be swept away and bridge can be demolished, while during drought, the embankment of the track can suffer from soil desiccation and embankment deterioration, high temperature increases the risk of track buckling and high winds can result in vegetation or foreign object incursion on to the infrastructure as well as additional quasi-static burden exerted. This review is of significant importance for planning and design of the newly proposed high speed rail link between Malaysia and Singapore.

Nearly half a century has passed since the discovery of cytoplasmic inheritance of human chloramphenicol resistance. The inheritance was then revealed to take place maternally by mitochondrial DNA (mtDNA). Later, a number of mutations in mtDNA were identified as a cause of severe inheritable metabolic diseases with neurological manifestation, and the impairment of mitochondrial functions has been probed in the pathogenesis of a wide range of illnesses including neurodegenerative diseases. Recently growing number of preclinical studies has revealed that animal behaviors are influenced by the impairment of mitochondrial functions and possibly by the loss of mitochondrial stress resilience. Indeed, as high as 54% of patients with one of the most common primary mitochondrial diseases, mitochondrial encephalomyopathy with lactic acidosis and stroke-like episodes (MELAS) syndrome, present psychiatric symptoms including cognitive impairment, mood disorder, anxiety, and psychosis. Mitochondria are multifunctional organelles which produce cellular energy and play a major role in other cellular functions including homeostasis, cellular signaling, and gene expression, among other. Mitochondrial functions are observed to be compromised and to become less resilient under continuous stress. Meanwhile, stress and inflammation have been linked to the activation of the tryptophan (Trp)-kynurenine (KYN) metabolic system, which observably contributes to development of pathological conditions including neurological and psychiatric disorders. This narrative review discusses the functions of mitochondria and the Trp-KYN system, the interaction of the Trp-KYN system with mitochondria, and the current understanding of the involvement of mitochondria and the Trp-KYN system in preclinical and clinical studies of major neurological and psychiatric diseases.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

The traditional manual recording of vaccination records in Germany faced challenges during the COVID-19 pandemic, prompting the introduction of a Covid smartphone app with QR codes. However, this solution brought new challenges, emphasizing the need for a centrally managed European digital vaccination record for efficiency and validity. Thus, this study assesses the feasibility of using the HL7 FHIR standard in the healthcare industry for implementing a digital vaccination pass management and monitoring system. The system aims to offer convenience and improved efficiency for both patients and healthcare providers while promoting interoperability with other healthcare systems. We developed a prototype using modern technologies, such as React, Quarkus, and Keycloak, evaluating the applicability of FHIR in promoting interoperability within the healthcare industry. Results indicate potential benefits for patients and healthcare providers, offering secure access to immunization records, personalized recommendations, and streamlined management. However, challenges in integrating nuanced vaccination processes into the standardized FHIR system, necessitating custom extensions, and issues with manual data entry and identity provider integration, pose obstacles. Despite these challenges, the study suggests that implementing HL7 FHIR can enhance efficiency, data accessibility, and accuracy in the vaccination process, supporting broader digitization efforts in the German healthcare system and beyond.

Tea infusions are the most consumed beverages in the world after water, their pleasant yet peculiar flavor profile drives consumer choice and acceptance and becomes a fundamental benchmark for industry. Any qualification method capable of objectifying the product's sensory features effectively supports industrial quality control laboratories guaranteeing high sample throughputs even without the human panel intervention. The current study presents an integrated analytical strategy acting as an Artificial Intelligence decision tool for black tea infusion aroma and taste blueprinting. Key markers validated by sensomics are accurately quantified in a wide dynamic range of concentrations. Thirteen key aromas are quantitatively assessed by standard addition with in-solution solid-phase microextraction sampling followed by GC-MS. On the other hand, nineteen key taste and quality markers are quantified by external standard calibration and LV-UV/DAD. The large dynamic range of concentration for sensory markers is reflected in the selection of seven high-quality teas from different geographical areas (Ceylon, Darjeeling Testa Valley and Castleton, Assam, Yunnan, Azores, and Kenya). The strategy acts as an AI smelling and taste machine predicting teas sensory features without the human panel intervention.

Intelligent systems are increasingly present in various areas of society, gaining special relevance in healthcare environments. In this work, grounded on previous developments proposed by the authors, the evolution and improvement of a novel intelligent system focused on the diagnosis of obstructive sleep apnea (OSA) is addressed. To do this, starting from two packages of information of a heterogeneous nature, and deploying a set of Machine Learning classification algorithms, focused each of them on different levels of the apnea-hypopnea index (AHI), as well as a set of cascaded expert systems, it is possible to obtain a series of risk metric pairs (Statistical Risk, Symbolic Risk) for each AHI level, understood as a warning forecast associated with the early detection of the pathology. The risk indicators of each pair are subsequently aggregated by means of a symbolic inference system, whose knowledge base was determined using the automatic rule generation approach proposed by Wang and Mendel. At the output of each inference system, a risk indicator is obtained for each AHI level, the Apnea Risk, whose interpretation makes it possible to discriminate between patients who could suffer OSA and those who do not, as well as to generate the appropriate recommendations. For the initial tests of the system, the design and development of a specific software artifact was carried out using data from 4,400 patients from the Álvaro Cunqueiro Hospital in Vigo, obtaining when applied to the test set AUC values within the range 0.74–0.88, which invites optimism and points to the benefits expected from the architecture of the proposed intelligent system.

Oil has become the object of global exploits and fierce competition among the major world powers as it is a key strategic non-renewable resource. Transnational petroleum investment is therefore an important mechanism available to countries and international corporations to control oil resources even though there are numerous inherent uncertainties and risks. A new risk assessment index system is proposed in this paper based on use of the Delphi expert scoring system and fuzzy comprehensive evaluation that aims to minimize the potential risks inherent to multinational petroleum investment. This approach encapsulates political, legal, socioeconomic, and infrastructural factors to develop a technical method that can be used for transnational petroleum investment risk assessment. An evaluation of oil investment risk within a case study area is also presented; results provide reference data that can be applied by national and international oil companies to mitigate risks of transnational oil investment.

The aim of this study is to solve the problems of complicated pretreatment and high analytical cost in the detection technology of trace drug toxicants in municipal wastewater. A high-performance magnetic sorbent was synthesized for enrichment of trace drug substances in wastewater to develop magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical methods for the molecules in wastewater drug toxicants. The magnetic nanospheres was successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinyl pyrrolidone.The results showed that the linear dynamic range of 17 drugs was 1-500 ng/L, the recovery was 43%-105%, the matrix effect was more than 67%, the limit of quantitative detection was 1-2 ng/L, and the detection time of each sample was 2.98s. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problem of complicated pre-treatment and analytical cost in the detection of drugs in wastewater. The developed magnetic material and acoustic excitation coupled mass spectrometry analysis method can realize the low-cost, efficient enrichment and fast analysis of different kinds of drug molecules in urban sewage.

This article discusses how, in today’s world of disruptive and dramatic social change (DSC), non-sports related coaching, which includes a wide range of services such as life coaching, career coaching, executive coaching, and team coaching, can inadvertently fuel undesirable social dynamics. There is little or no awareness of this risk among coaches and coachees. The global, fast-growing, multi-billion-dollar industry aimed at supporting people and organisations to perform better and increase wellbeing while managing and adapting to change has been developed with limited sociological input. The article is based on 15 years of social constructionist-informed reflective practice by a sociologist-turned-coach, and uses a multi-layered autoethnographic account to argue for a sociologically informed paradigm shift in coaching, as well as relevant sociological knowledge and social and human sciences research methodology in coaches’ education. It presents the rationale and key features of a new coaching approach that places DSC-relevant sociological concepts at the heart of the coaching process, helps people develop psycho-sociological awareness, and uses a learning-to-develop through research design. A new definition of coaching to address DSC is derived. Coaching practitioners will find DSC-relevant sociological concepts, critical reflections, coaching questions, and procedures to expand coaching effectiveness. Interdisciplinary research topics combining coaching sociology and coaching psychology are suggested.

The sustainability of ecotourism is the backbone of tourism development of a country. Ecotourism can contribute to both conservation and development in which involves dynamic relationship between tourism, biodiversity and communities, facilitate by great management. The purpose of this study is to analyze the dimensions of the socio-economic and environmental impacts of ecotourism in communities surrounding the Tasik Kenyir in Terengganu, Malaysia. This study provides a framework for the development and evaluation of ecotourism. The framework will determine if the relationships between indicators are positively correlated which will result in positive contribution to the other by using System Dynamic. Socio-cultural and economic data will be collected through interviews and group discussions in selected communities in Tasik Kenyir. Data on wildlife will be extracted from secondary data from Kenyir Research Institute, Universiti Malaysia Terengganu. The data analysis will explore the socio-cultural and economic differences between and within different communities due to ecotourism development, the contribution of ecotourism to conservation activities, local support for conservation and ecotourism as well as the influence of tourist activities on the distribution of wildlife species in Tasik Kenyir. This study aims to contribute toward understanding the natural resource community-ecotourism inter-relationship and help to bridge the knowledge gap that hinders biodiversity conservation initiatives. The findings will be used as a base for further development of ecotourism and will recommend alternative management options where necessary for the study area.

We describe an interesting case report about a patient with hemophilia A with severe chronic elbow arthropathy who underwent multiple surgical because of his condition. We collected all the clinical and imaging findings, and we compared the decision-making flow chart and the surgery performed with the most recent indications, treatments and complications reported in the literature. The aim of this case report is to show how usually the hemophilic patient even if young usually comes to our attention from the beginning with complex and advance musculoskeletal disease. Elbow hemophilic arthropathy is a complex disease and the management in these patients could be more difficult than others because of the higher risk of complications rate after all surgical procedures, for this reason it’s very important to treat these patients in hub centers with expertise in well-coordinated multidisciplinary teams. The path from diagnosis to surgical treatment of hemophilic elbow arthropathy can be a risky one, as it happened in this case.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

Access to medical care is a global issue. Technology-aided approaches have been applied in addressing this. Interventions have however not focused on medical diagnosis as a fully automated procedure and available applications employ mainly text-based inputs rather than conversation in natural language. We explored the utility of ontology-based chatbot technology for the design of intelligent agents for medical diagnosis through a systematic review of the most recent related literature. English articles published in 2011-2016 returned 233 hits which yielded 11 relevant articles after a 3-stage screening. Findings showed that the creation of expert systems had been the focus of many the studies which utilize the physician-system-patient framework with system training based mostly on expert knowledge for designing web- or mobile phone-based applications that serve assistive purposes. Findings further indicated gaps in the design and evaluation of more effective systems deployable as standalone applications, for example, on an embodied robotic system. The need for technology supporting the physical examination part of diagnosis, connection to data sources on patients’ vitals and medical history are also indicated in addition to the need for more qualitative work on natural language-based interaction. The system should be one that is continuously learning. Future works should also be directed towards the building of more robust knowledge base as well as evaluation of theory-based diagnostic methodological options

Objective: The long-term care insurance (LTCI) system was introduced in 2000 to provide financial support for long-term care services to older adults. What is known on this topic report focuses on a comparative analysis of how the LTCI system has affected older people in Japan. Methods: We obtained data from the literature about the LTCI system, compared and analysed the collected articles, and concluded. Results: The LTCI system has improved access to long-term care services, with more older adults receiving care than before the system’s implementation. This service has improved the quality of life for many elderly individuals who require assistance with daily activities. Furthermore, the LTCI system has alleviated the financial burden of long-term care services since the insurance covers a large portion of the costs. It has made older adults maintain their independence and dignity, as they can afford the necessary care without relying solely on their savings or burdening their families. Conclusions: Japan’s LTCI system has positively impacted older adults by improving access to long-term care services and alleviating financial burdens. However, challenges such as increasing demand and variations in service quality need to be addressed to ensure the system effectively supports older people in Japan.

In the past few years, micromodels have become a useful tool for visualizing flow phenomena in porous media with pore structures, e.g., the multifluid dynamics in soils or rocks with fractures in natural geomaterials. Micromodels fabricated using glass or silicon substrates incur high material cost; in particular, the microfabrication-facility cost for making a glass or silicon-based micromold is usually high. This may be an obstacle for researchers investigating the two-phase-flow behavior of porous media. A rigid thermoplastic material is a preferable polymer material for microfluidic models because of its high resistance to infiltration and deformation. In this study, cyclic olefin copolymer (COC) was selected as the substrate for the micromodel because of its excellent chemical, optical, and mechanical properties. A delicate micromodel with a complex pore geometry that represents a two-dimensional (2D) cross-section profile of a fractured rock in a natural oil or groundwater reservoir was developed for two-phase-flow experiments. Using an optical visualization system, we visualized the flow behavior in the micromodel during the processes of imbibition and drainage. The results show that the flow resistance in the main channel (fracture) with a large radius was higher than that in the surrounding area with small pore channels when the injection or extraction rates were low. When we increased the flow rates, the extraction efficiency of the water and oil in the mainstream channel (fracture) did not increase monotonically because of the complex two-phase-flow dynamics. These findings provide a new mechanism of residual trapping in porous media.

We have presented a controllable and human-readable polynomial neural network (CR-PNN) that is the first human-readable neural network. One can imagine its influence on system identification. Subsequently, we developed a relation spectrum in a medical application, which is likely to stand alongside the Fourier spectrum. However, the system analysis methodology is incomplete in contrast to signal processing methodology. Here, we presented the system filters for the first time. In this paper, we used the simulation system to verify the availability of the system analysis methodology. The system analysis methodology showed great properties in system identification and filter. The contribution of this paper is the system analysis methodology: transform method (CR-PNN), relation spectrum, and system filter design.

Polymeric based nanoparticles are garnering significant interest for their potential in drug delivery. Specially, nanopolymers that have been functionalized with molecules, such as proteins or peptides, are a versatile vehicle for drug delivery. Curcumin (Cur) is one of the most commonly studied anticancer compounds and is widely acknowledged as having positive effects on human health. However, its insolubility and low bio-distribution greatly hinder the exploitation of its beneficial traits. In this study, our team created a nano delivery system which utilized a nanopolymer called PCL-PEG (poly(ε-caprolactone)-poly (ethylene glycol)). This system was functionalized with A6 peptide to enable targeted delivery of Cur. The system was designed with advantageous nanoparticles (NPs), including a stable zeta potential (–32.7), small size (54.3), uniform surface morphology, and high hydrophilicity (13.72°). In addition, targeted delivery systems exhibited high encapsulation efficacy (93 ± 0.89 %), and drug loading (16.7 ± 0.9 %), and were characterized by a slow and gradual release profile with a release of approximately 83.13 ± 0.12%. The MTT assay results showed that the formulation known as Cur-NPs-A6 caused a significant increase in cell death in MDA-MB-231 cancer cells (IC50 = 23.31 ± 0.85 µM). The designed delivery system did not cause any harm to the noncancerous MCF-10A cells (normal group). Furthermore, the results of both the RT-qPCR and invasion assays demonstrated that the designed system was able to effectively activate the apoptosis pathway and inhibit cell invasion. Our findings suggest that the use of the designed smart delivery system, which is functionalized with A6 peptide that has a high affinity for CD44 receptor - known to be upregulated in numerous malignant conditions, could be a highly efficient approach to treating cancer.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Sulfate, the main dissolved contaminant in acid mine drainage (AMD), is ubiquitous in watersheds affected by coal and metal mining operations worldwide. Engineered passive bioremediation systems (PBS) are low-cost technologies that remediate sulfate contamination by promoting (1) precipitation of sulfate-bearing compounds, such as schwertmannite and gypsum; and (2) microbially-mediated sulfate reduction (BSR) to sulfide with subsequent precipitation of sulfide minerals. In this study, chemical and sulfur isotopic data are used to infer multiple pathways for sulfate sequestration in the Tab-Simco PBS. By simultaneously monitoring sulfate concentrations and δ34SSO4 values at four sampling points across the PBS, we (1) identified that the organic layer within the bioreactor was the primary site of BSR processes contributing to sulfate sequestration; (2) observed seasonal variations of BSR processes; (3) estimated that initially the BSR processes contributed up to 30% to sulfate sequestration in the Tab-Simco bioreactor; and (4) determined that BSR contribution to sulfate sequestration continuously declined over the PBS operational lifetime. Together, our results highlight the utility of combining geochemical and microbial fingerprinting techniques to decipher complementary processes involved in sulfur cycling in a PBS as well as the value of adding the sulfur isotope approach as an essential tool to help understand, predict, prevent and mitigate sulfate contamination in AMD-impacted systems.

The successful 2020 launch and 2021 landing of the National Aeronautics and Space Administration’s (NASA) Perseverance Mars rover initiated the first phase of the NASA and European Space Agency (ESA) Mars Sample Return (MSR) campaign. The goal of the MSR campaign is to collect scientifically interesting samples from the Martian surface and return them to Earth for further study in terrestrial laboratories. The MSR campaign consists of three major spacecraft components to accomplish this objective: the Perseverance Mars rover, the Sample Retrieval Lander (SRL) and the Earth Return Orbiter (ERO). Onboard the ERO spacecraft is the Capture, Containment and Return System (CCRS). CCRS will capture, process and return to Earth the samples that have been collected after they are launched into Mars orbit by the Mars Ascent Vehicle (MAV), which is delivered to Mars onboard the SRL. To facilitate the processing of the orbiting sample (OS) by CCRS we have designed and developed a vision system to determine the OS capture orientation. The vision system is comprised of two cameras sensitive to the visible portion of the electromagnetic spectrum and two illumination modules constructed from broadband light emitting diodes (LED). Vision system laboratory tests and physics-based optical simulations predict CCRS ground processing will be able to correctly identify the OS post-capture orientation using only a single vision system image that is transmitted to Earth from Mars orbit.

Continuum robots play the role of end-effector in various surgical robots and endoscopic devices. The robots may be categorized as rigid or soft continuum robots (SCRs). While the SCRs have proven advantages such as safety and compliance, more research and development are required to enhance their capability for specific medical scenarios. This research aims at designing a soft robot considering concepts of geometric and kinematic similarities. The chosen application is a semi-invasive medical application known as Transesophageal Echocardiography (TEE), but the methodology can be implemented in other similar applications. Since established rigid carrier construction make use of principles we find as well embodied in vertebral spines, the paragon for soft robot solution can be the phylogenetic precursor of the spine, the Chorda dorsalis. The feasibility of fabrication of a soft endoscopic device derived from that paragon within a robotics laboratory was shown empirically by producing a three-segment pneumatic SCR. The kinematic model was proposed based on the method of transformation matrices, and an algorithm based on a self-organizing map (SOM) was proposed and applied to realize kinematic similarity. The simulation results indicate that the algorithm acting as an open-loop controller forces the soft robot tip to follow the desired path which in this case is the path of the rigid probe. It is concluded that the solution provides a soft robot that can surrogate and succeed the traditional rigid counterpart owing to size, workspace, and kinematics.

New technologies have resulted in a better understanding of blood and lymphatic vascular heterogeneity at the cellular and molecular levels. Meanwhile, we still need to learn more about the heterogeneity of the cardiovascular and lymphatic systems between different species at the anatomical and functional levels. Even the deceptively simple question of the functions of fish lymphatic vessels has yet to be conclusively answered. The most common interpretation assumes a similar dual setup of the vasculature in zebrafish and mammals: on the one hand, there is the cardiovascular, circulatory system, and on the other hand, the lymphatic vascular system, in which the unidirectional flow is derived from surplus interstitial fluid and returned into the cardiovascular system. A competing interpretation questions the identity of the lymphatic vessels in fish as at least some of them receive their flow from arteries via specialised anastomoses, neither requiring an interstitial source for the lymphatic flow nor stipulating unidirectionality. In this alternative view, the “fish lymphatics” are a specialised subcompartment of the cardiovascular system, called the “secondary vascular system” (SVS). Many of the contradictions found in the literature appear to stem from the fact that the SVS develops in part or its entirety from an embryonic lymphatic vascular system by transdifferentiation. Future research needs to establish the extent of embryonic transdifferentiation of lymphatics into SVS blood vessels. Similarly, more insight is needed into the molecular regulation of vascular development in fish. Most fish do feature more than the five VEGF genes and three VEGF receptor genes that we know from mice or humans, and the relative tolerance of fish to whole genome and gene duplications could underlie the evolutionary diversification of the vasculature. This review discusses the key elements of the fish lymphatics versus the SVS and attempts to draw a picture coherent with the existing data, including the phylogenetic knowledge.

Aiming at the difficult problem of broadband oscillation localization in power systems, the intel-ligent localization method of oscillation source based on the digital twin is proposed and the os-cillation source localization system based on the digital twin is constructed. Firstly, a digital twin-based oscillation source localization method and system architecture are proposed. Fur-thermore, an intelligent positioning method of oscillation source based on data-driven and mechanism fusion is proposed. It includes three steps: oscillation signal preprocessing, oscillation modal analysis and oscillation source localization. For the oscillation signal preprocessing, the generative adversarial imputation network is used to repair the missing samples, and the su-per-resolution technique is used to realize the super-resolution measurement of broadband os-cillation. In the oscillation modal analysis, the spectrum of the oscillation signal is extracted using the fast Fourier transform. To accurately locate the oscillation source, the branch potential energy is used as input to the data-driven model, such as LSTM and CNN. Finally, an oscillation source localization system is developed based on the digital twin workshop CloudPSS-XStudio, which can locate the oscillation source quickly and accurately.

The increase in the rate and prevalence of diseases associated with the localized and general loss of bone mass calls for an investigation into therapeutic alternatives that largely involve the de-velopment of new biomaterials and cell therapy, converting tissue bioengineering into a prom-ising option. An experimental model of a critical mandibular lesion in rats has been used to study bone re-generation by treating the ostectomy with the biomaterials Evolution® and Gen-Os® (OsteoBiol®, Italy) combined, or not, with dental pulp stem cells (DP-MSC). The results obtained through the Micro-CT and histological study reveal the almost complete re-covery of the lesion in the group with DP-MSC. These results are supported by increases in endoglin, TGF-β, protocollagen I, parathormone, and calcitonin, generating an environment of bone generation and development when combining Evolution® and Gen-Os® (OsteoBiol®, Italy) with DP-MSC. These promising results confirm the transcendental role of DP-MSC in combina-tion with osteogenic biomaterials for bone regeneration, and warrant further studies, including its assessment in clinical trials.

Origin, mechanics and properties of the Solar System are analysed in the framework of the Complete Relativity theory (by the same author). According to Complete Relativity, everything is relative. Any apparent absolutism (notably invariance to scale of dimensional constants, absolute elementariness, invariance to time) is an illusion stemming from limits imposed by [or on] polarized observers that will inevitably lead to misinterpretation of phenomena (another illusion) occurring on non-directly observable scales or even on observable but distant scales in space or time. If everything is relative, reference frames will exist where particles are planets and where planets are living beings. Earth is, therefore, analysed here in more detail, both as a particle and, as a living evolving being (of, hypothesized, extremely introverted intelligence). The analysis confirms the postulates and hypotheses of the theory (ie. existence of discrete vertical energy levels) with a significant degree of confidence. During the analysis, some new hypotheses have emerged. These are discussed and confirmed with various degrees of confidence. To increase confidence or refute some hypotheses, experimental verification is necessary. Main conclusions that stem from my research and are further confirmed in this paper are: universes are, indeed, completely relative; Solar System is a scaled (inflated, in some interpretations) Carbon isotope with a nucleus in a condensed (bosonic) state and components in various vertically excited states; life is common everywhere, albeit extroverted complex forms are present on planetary surfaces only during planetary neurogenesis; anthropogenic climate change is only a part (trigger from one perspective) of bigger global changes; major extinction events on a surface of a planet are relative extinctions, a regular part of transformation and transfer of life in the process of planetary neurogenesis.

—The number of ATMs in various countries is increasing steadily and rapidly with the number of users increasing very widely. On the other hand, banks have become more interested in finding the best procedures to combat ATM crimes to ensure the safety and security of their customers and other cardholders. This has become an excellent target for some criminals or fraudsters, despite the limited amounts that can be withdrawn from these devices, given a maximum daily limit. We aim at implementing this system inside bank ATMs in order to detect objects like guns, hammers, and knives. Once the suspicious objects and actions are detected, we perform facial recognition to identify whether the suspect is a repeating offender. We use object, face, and action recognition algorithms to achieve our objective. Results showed that using our proposed algorithm is efficient in detecting threatening objects

This review describes the positive effects of growth hormone on the cardiovascular system. We analyze why the vascular endothelium is a real internal secretion gland, whose inflammation is the first step for developing atherosclerosis, as well as the mechanisms by which GH acts on the vascular endothelium improving its dysfunction. We also report how GH acts on coronary arterial disease and heart failure, and on peripheral arterial disease inducing the generation of new collateral vessels able to bypass a major artery occlusion. We include some preliminary data from a trial in which GH or placebo is given to elder people suffering from critical limb ischemia, showing the effects of the hormone on plasma markers of inflammation, and stating that the administration of GH in short periods of time is safe and effective even in diabetic patients. We also analyze how Klotho may have strong relationships with GH, inducing, after being released from the damaged vascular endothelium, the pituitary secretion of GH to repair the damaged tissue. Lastly, we show how GH induces wound healing by increasing the blood flow to the ischemic tissue. In summary, we postulate that short-time GH administration is useful for treating cardiovascular diseases.

Autonomous vehicle technology, employing image sensors for road marking recognition, is largely dependent on the Lane Departure Warning System (LDWS) to prevent vehicular deviations from driving lanes. The effectiveness of image-based lane recognition, however, is susceptible to environmental influences like weather conditions and the surrounding road environment. This study investigates the impact of road marking retro-reflectivity on LDWS under varied environmental conditions. Conducted at the Yeoncheon SOC Demonstration Research Center, the experiments encompassed a spectrum of weather scenarios, incorporating rainfall and shifts between day and night lighting. Controlled wear was applied to white, yellow, and blue road markings, followed by measuring their retro-reflectivity at different stages of degradation. The LDWS's performance was evaluated by assessing the recognition rates of these markings under these diverse environmental settings. The study reveals that enhanced retro-reflectivity significantly boosts LDWS detection, especially in challenging weather conditions. Furthermore, the research led to the development of a simulation framework to analyze the cost-effectiveness of road marking maintenance, aligning it with the safety needs of autonomous vehicles. This framework suggests the necessity for updated road marking guidelines that cater to the advanced needs of driver assistance systems and autonomous vehicle technology.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

Cannabis has long been used for its medicinal and psychoactive properties. With the relatively new adoption of formal medicinal cannabis regulations worldwide, the study of cannabinoids, both endogenous and exogenous, has similarly flourished in more recent decades. In particular, research investigating the role of cannabinoids in regeneration and neurodevelopment has yielded promising results in vertebrate models. However, regeneration-competent vertebrates are few, whereas a myriad of invertebrate species have been established as superb models for regeneration. As such, this review aims to provide a comprehensive summary of the endocannabinoid system, with a focus on current advances in the area of endocannabinoid system contributions to invertebrate neurodevelopment and regeneration.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

AbstractBackground: In digitalization era, health care system was conditioned with the health worker’s ability to adapt media of digital technology. Digital technology media was used to strengthening and fasted the health care for patient and community. Aims: This study aimed to explore the accurate information of health professional utilization digital technology during doing the job at the health facilities in Timor-Leste. Methods: This study was used correctional study with 56 respondents was participated in the study. Was collected the data from 1 to 30 February 2023. Was used questioner of google form based for data collection. Data collection was distributed via online with google form to social media as WhatsApp’s, email and face book and twitter to completed by respondents. The inclusive Criteria are: health professional living in Timor-Leste, to able response the questioner. Was used descriptive analysis in this study. Finding: This study was indicated that majority of health professional was participated in the study as 54,2% man then women have 45,8%. About 100% health professional used hand phone to facilitate their daily activities including related with their work activities. Other side indicated in digital technology tools use are able to use Microsoft word is 78,3%, able to use Microsoft Excel is 76,7% and able to use Power Point is 81,7%. E-mail use about 89,2%, WhatsApp’s use 81,7%, About 74,2% was used zoom/webinars/Google meet application, about 72,5% sad that they were used computer in the work place until now. Around 96.4% need to improve or deepen their knowledge and skills in using ICT in the future to facilitate they are activity. Conclusion: Majority of health professional in Timor-Leste was used the computer, internet, hand phone in daily activities. Majority need to gate the training to improve their knowledge, attitude and psychomotor in the future.

This study examines the performance of the Indian Monsoon Data Assimilation and Analy-sis (IMDAA) in predicting five extremely severe cyclonic storms (ESCS) over the Bay of Bengal. The Advanced Research version of the WRF (ARW) model is utilized for this analysis over the last two decades. The initial and lateral boundary conditions are derived from the IMDAA datasets with a horizontal resolution of 0.12° × 0.12°. Five ESCSs from the past two decades are considered: Sidr 2007, Phailin 2013, Hudhud 2014, Fani 2019, and Amphan 2020. The model is integrated up to 96 hours using double nested domains of 12 km and 4 km. Model performance is evaluated using the 4 km results, compared with available observational datasets, including the best-fit data from the India Meteorological Department (IMD), The Tropical Rainfall Measuring Mission (TRMM) satellite, and Doppler Weather Radar (DWR). The results indicate that IMDAA provides accurate forecasts for ESCSs Fani, Hudhud, and Sidr in terms of track, intensity, and mean sea level pressure, aligning well with IMD observational datasets. However, Sidr's track deviates more from the observations. The calculated mean absolute maximum sustained wind speed errors range from 8.4 m/s to 10.6 m/s from day-1 to day-4, while mean track errors range from 114 km to 496 km during the same period. Statistical analysis, including bias, mean error, and standard deviation, underscores the significance of ESCS prediction. The discussion also covers rainfall prediction, maximum reflectivity, and the associated structure of the storms.

Energy management, especially in communities, is attracting growing interest, but is often marred by confusion between the terms "Energy Information System" (EIS) and "Energy Man-agement System" (EMS). This ambiguity hinders understanding of their use and role in improv-ing energy performance. Our objective is to clarify these terms and their contribution to energy management. We used a mixed qualitative and quantitative approach to evaluate and compare the criteria of definition, objective, functionality, role, as well as correlated elements such as or-ganizational structure, responsibilities, planning and policy, according to the requirements of ISO 50001, in addition to criteria specific to the two systems. The study reveals differences in the roles of the EIS and the SME, with a complementarity of 40% between the two systems, depend-ing on the positioning of the EIS in relation to the elements of the SME process. The EIS plays a crucial role in facilitating the implementation of the EMS according to ISO 50001. This clarifica-tion contributes to a better understanding of the respective roles of these systems in energy management, thus helping communities to improve their energy performance in an effective manner.

In this paper, we propose a novel approach to the development of green public policies. We emphasize the significance of the System of Systems (SoSs) methodology, which concentrates on understanding and managing complex systems by contemplating their interdependencies and interactions as a single integrated system. Based on this perspective, we view green public policy as a system interacting with the energy, health, pollutants, and economic systems of the SoSs. We employ both Decision-Making Trial and Evaluation Laboratory (DEMATEL) and Interpretive Structural Modeling (ISM) techniques as a method of systematic structural analysis to comprehend the relationships between the aforementioned systems. We provide a comprehensive literature review on the application of these soft operation research (SOR) techniques. We note that SOR methods are suitable for the formulation of effective and long-lasting public policies. Using an example, we demonstrate the primary advantage of DEMATEL and ISM, which is the establishment of easily comprehendible causal relationships between the systems in the SoSs.

Cancer-associated cachexia (CAC) is a debilitating condition marked by muscle and fat loss, unresponsive to nutritional support, and contributes significantly to morbidity and mortality in patients with cancer. Immune dysfunction, driven by cytokine imbalance, contributes to CAC progression. This review explores the potential relationship between CAC and anti-cancer immune response in pre-clinical and clinical studies. Pre-clinical studies showcase the involvement of cytokines like IL-1β, IL-6, IL-8, IFN-γ, TNF-α, and TGF-β, in CAC. IL-6 and TNF-α, interacting with muscle and adipose tissues, induce wasting through JAK/STAT and NF-κB pathways. Myeloid-derived suppressor cells (MDSCs) exacerbate CAC by promoting inflammation. Clinical studies confirm elevated pro-inflammatory cytokines (IL-6, IL-8, TNFα) and immune markers like neutrophil-to-lymphocyte ratio (NLR) in patients with CAC. Thus, immunomodulatory mechanisms involved in CAC may impact the anti-neoplastic immune response. Inhibiting CAC mechanisms could enhance anti-cancer therapies, notably immunotherapy. R-ketorolac, a new immunomodulator, reversed weight loss and increased survival in mice. Combining these agents with immunotherapy may benefit patients with cancer experiencing CAC. Further research is vital to understand the complex interplay between tumor-induced immune dysregulation and CAC during immunotherapy.

The paper draws attention and opens the debate on major societal issues that concern not only Muslims but human societies, at large, because of their profound implications, afflictions, and their present and future transitive dimensions. The paper discusses two major issues that have attracted a great deal of attention in the recent past: wealth and income disparities, and global indebtedness. Four remedies have stressed upon and/or proposed to eradicate and/or lessen some of the burdens of these problems have been thoroughly examined. These are: - Stripping commercial banks of their power to create money out of thin air (i.e., Ex Nihilo). Thus, reviving financial reform in line with the spirit of the call for the “Establishment of a National Bank [in England]” in the 1820s by the renowned British economist David Ricardo (1772-1823). The Bank of England was a private commercial entity at that time. - Prohibiting of ‘harmful’ speculation activities in financial and economic transactions and/or imposing hefty taxes on transactions relating to such activities. The implementation of such a policy requires and clear-cut distinction between the ‘harmful’ and ‘non-harmful’ speculative activities in financial and non-financial markets. - Levying adequate and fair taxes on the wealthiest upper class at the global scene. Calls for such a policy is on rise in the past few years. For instance, “Speakers at the European Development Days summit in Brussels, [in 2017], said that a just tax system should be “at the heart” of the development debate, and that more transparency is needed to ensure that companies pay their fair share. Tax avoidance schemes used by multinational companies, such as moving profits to tax havens, result in global losses of around $650 billion a year in tax receipts — with developing countries losing $200 billion, according to a study from the International Monetary Fund”, (Edwards, 2017; Crivello et al., 2015, p. 21) - Establishing a neutral legislative and tax regimes for different modes of financing. Thus, providing ‘a level playing field’ for equity and debt modes of financing due to the current biasness of the tax regimes to debt-based financing instruments as it has been documented in various studies carried out by the IMF, the European Commission, and other international prominent bodies.

The endocannabinoid system (eCB) began to be studied from the identification of the molecular structures present in the cannabis sativa plant. The ECS is constituted of cannabinoid receptors, endogenous ligands and all the associated enzymatic apparatus responsible for maintaining homeostasis. Several physiological effects of cannabinoids are exerted through interaction with various receptors such as CB1 and CB2 receptors, vanilloid receptors, and the recently discovered [GPCRs (GPR55, GPR3, GPR6, GPR12 and GPR19). Endogenous ligands such anandamide and 2-arachidonoylglycerol might modulate these receptors. eCB has proved to play a critical role in some human diseases and has been extensively studied due to its wide therapeutic potential and because it is a promising target for the development of new drugs. Phytocannabinoids and synthetic cannabinoids have shown varied affinities to eCB, which are relevant to the treatment of various diseases. They may also have potential as lead compounds in the development of cannabinoid-based pharmaceuticals for a variety of diseases. Furthermore, Integrative and Complementary Health Practices (ICHP) appear to influence the endocannabinoid system through modulation. This review will show a description of ECS components and discuss how phytocannabinoids, other exogenous compounds, and PICS may operate the eCB balance.