To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

A reduced order model is developed to monitor aeroengines condition (defining their degradation from a baseline state) in real-time, by using data collected in specific sensors. This reduced model is constructed by applying higher order singular value decomposition plus interpolation to appropriate data, organized in tensor form. Such data are obtained using a detailed engine model that takes the engine physics into account. Thus, the method synergically combines the advantages of data-driven (fast online operation) and model-based (the engine physics is accounted for) condition monitoring methods. Using this reduced order model as surrogate of the engine model, two gradient-like condition monitoring tools are constructed. The first tool is extremely fast and able to precisely compute `on the fly’ the turbine inlet temperature, which is a paramount parameter for the engine performance, operation, and maintenance, and can only be roughly estimated by the engine instrumentation in civil aviation. The second tool is not so fast (but still reasonably inexpensive) and precisely computes both, the engine degradation and the turbine inlet temperature at which sensors data have been acquired. These tools are robust in connection with random noise added to the sensors data and can be straight forwardly applied to other mechanical systems.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

Through a partnership with three Federally Qualified Health Centers (FQHCs), the local health department in Los Angeles County implemented a produce prescription program (PPR) to increase fresh fruit and vegetable purchases among patients with diabetes or prediabetes. The PPR, which began in 2020, provided eligible patients with a $40 voucher every month for 6 months to promote the purchase of fresh produce at large chain grocery stores. This qualitative assessment describes staff experiences with the PPR, documenting the facilitators and barriers they encountered while implementing the program. Fifteen clinic staff (i.e., PPR implementers) were interviewed for this assessment. Thematic analysis and coding were conducted using the ATLAS.ti software; the coding was carried out by two separate coders. Interviewees discussed the importance of having preexisting partnerships and programs to support the PPR at their clinic site. Hidden costs related to implementing the program included a large and unexpected amount of staff time devoted to enrolling patients into the program. Collecting quality data and having limited expertise to rigorously evaluate the program were other challenges. Because patients often share their food with their family, the monthly $40 incentive was generally not enough to support their needs; interviewees suggested giving a higher inventive amount to those with a larger household. Future PPR efforts and similar food incentive programs should consider these and other facilitators and barriers to implementation and sustainability, especially when making adjustments to these programs to improve services and access to food resources.

Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

: Electric air conditioning and heating systems capacity is growing rapidly. So does the nameplate capacity of PV power plants. While demand in cooling has a positive correlation with solar irradiationirradiance, the demand in heating has an opposite relation. In this study, different approaches of to design (aggregation; energy storagethermal, battery and implicit systems storage) and control (frequency conversion; variable and adaptive load) and their effects on the efficiency of an off-grid active thermal stabilisation system based on a solar-powered heat pump are analysed. The case considered is permafrost thermal stabilisation system in Norway. It is shown that proper layout and control of the system with an adaptive load can reduce the capital expenses expenditures and the total cost of ownership by 30-40%. Increase in the efficiency capacity factor and cooling stability of the systems with the aggregated and threshold power consumervariable load due to the principle of aggregation is studied. The downside of that is the increase in compressors operation time by 50% with variable load and by 25% per unit with aggregation which means more frequent replacement in terms of motor-hours. But The the feasibility of this approaches considered are applicable for a wide range of solar-powered facilities, but the results are is quite case sensitive and depends on the prices for low-power heat pumps. The prospects of using the excess refrigerant and soil for thermal energy storage instead of traditional electrochemical batteries are considered.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

In the context of energy decarbonization, wind farms with type IV wind turbines from various manufacturers are being massively put into operation. These wind turbines comply with the requirements of the grid codes of the countries where they are designed and/or manufactured, but do not factor in the specific features of the distribution networks of other countries to which they are connected. The study at issue involves a comparative analysis of the requirements of grid codes of different countries for the stable operation of wind turbines under standard disturbances. The Low Voltage Ride Through (LVRT) characteristic implemented in type IV wind turbine inverters makes it possible to prevent wind turbine shutdowns in case of short-term voltage dips of a given depth and duration. The calculations of transient processes indicate that wind turbines may not meet the requirements of the grid code of a particular country for their stable operation. As a result, standard disturbances will block the reactive current injection and the wind turbine will be switched off. This is often caused by the relay protection devices with a time delay of 1-2 s, which are used in distribution networks and implement the functions of long-range redundancy. Excessive shutdowns of wind turbines lead to emergency rise in the load for the generating units of conventional power plants, aggravating the post-accident conditions and disconnecting consumers of electricity. The paper presents a method for checking the LVRT characteristic settings for compliance with the technical requirements for wind turbines. To prevent wind turbine outages, one should either change the configuration of the LVRT characteristic, or upgrade the relay protection devices in the distribution network adjacent to the wind farm, or implement group or individual technical solutions at the wind farm. The performance of the proposed technical solutions is confirmed by the calculations of transient processes.

The utilization of wind energy has become increasingly popular in the United States and many European countries due to its abundant natural source and optimized design. While existing wind turbines are predominantly large-scale and not suitable for standalone or distributed power production, Lubbock County in West Texas offers a diverse range of renewable energy options to meet its energy needs. The region relies heavily on utility-scale wind energy sources to supply power to the Texas Grid, replacing conventional fossil fuel-based systems. Currently, standalone solar PV systems are the preferred choice for renewable energy generation. However, West Texas possesses an ample supply of wind energy that can be harnessed to establish a microgrid and provide standalone power to rural communities. By employing the latest technology and optimizing efficiency, even in low-scale generation, a 6 kW permanent magnet alternator-based distributed wind turbine has been designed. This paper focuses on analyzing the techno-economic aspects of implementing this wind turbine in a real-world scenario, taking into account wind attributes such as velocity and available power at the specific location.

Cross-field innovation in faba bean breeding has added significant value to the traditional faba bean planting industry by allowing for the selection of faba bean varieties with a dual purpose as ornaments and food. In order to improve the selection efficiency, we determined 17 phenotypes related to ‘dual purpose’ faba beans and evaluated 37 new breeding lines, which were bred for 10 years by our team, and two traditional faba bean varieties by means of an Analytic Hierarchy Process. The lines and varieties were evaluated and sorted into five grades, from which two breeding lines with excellent comprehensive phenotypes and dual ornamental and food functions were selected. The new line GS5 passed the identification of Crop Identification Committee of Chongqing Seed Industry Association on November 25, 2021 and was renamed "Doumei 1 hao" with the identification number of " 202111". The results confirmed that the comprehensive evaluation system constructed in this study can be used for the effective selection of dual-purpose faba bean lines, providing an empirical approach for strategic decision-making by breeders.

Wind power is one of the most important sources of renewable energy available today. A large part of the wind energy cost is due to the cost of maintaining wind power equipment. When a wind turbine component fails to function, it might need to be replaced under the less than ideal circumstances. This is known as corrective maintenance. To minimize unnecessary costs, a more active maintenance policy based on the life expectancy of the key components is preferred. Optimal scheduling of preventive maintenance activities requires advanced mathematical modeling. In this paper, an optimal preventive maintenance algorithm is designed using the renewal-reward theorem. In the multi-component setting, our approach involves a new idea of virtual maintenance which allows us to treat each replacement event as a renewal event even if some components are not replaced by new ones. The proposed optimization algorithm is applied to a four-component model of a wind turbine and the optimal maintenance plans are computed for various initial conditions. The modeling results showed clearly the benefit of PM planning compared to pure CM strategy (about 30% lower maintenance cost).

Hydrogen powered vehicles use high-pressure reservoirs from which the gas is transferred to the low-pressure fuel-cell via a classical pressure reduction valve. In these systems no expansion work is recovered and the question is addressed of the potential to increase the global efficiency by using an expansion machine between the reservoir and the electrochemical reactor. This paper investigates the feasibility of such an expansion machine, evaluates the mechanical constraints in terms of forces, torques and produced power by numeric simulation. It further evaluates the energetic contribution to the whole conversion chain from the hydrogen reservoir to the common electrical network on board. A low energy contribution of the expansion system addresses the question of the real benefit of such an investment.

For engines operating with heavy fuel oil (HFO), the nozzle rings of the turbocharger turbines are prone to severe degradation in terms of contamination with unburned fuel deposits. This contamination may lead to increased excitation of blade resonances. A previous study provides technical guidelines on how to extract the relevant information from the pulsation spectra by means of a single probe installed away from the turbine trailing edge and some sound experimental proofs of integral mode turbine vibration detection. These theoretical discussions only allude to the effects of mistuning and interferences due to classical blade passing frequencies on sound radiation patterns emitted by integral blade vibration modes. In this paper, both effects are thoroughly discussed. Combining the knowledge of theoretical study and further experimental results, the application range of this blade vibration detection method can be remarkably extended.

An experimental investigation on the heat pump performance improvement equipped with the two-phase ejector called “an ejector-expansion heat pump (EEHP)” is proposed. The system performance of the EEHP is compared with a vapour-compression heat pump (VCHP). The improvement potential is determined and discussed. The heat pump test system is constructed which is based on a water-to-water heat pump. It can be experimented with both EEHP and VCHP. The two-phase ejector with the cooling load up to 2500 W is installed for experiment. The results show that the EEHP always produces a higher heating rate and COP than the VCHP throughout the specified working conditions. The heating COP is increased by 5.7-12.2% depending on the working conditions. It is also that under the same heat sink and heat source temperature, the EEHP can produce lower compressor discharge temperature and lower compressor pressure ratio than the VCHP. This is evidence that the two-phase ejector can provide better compressor working characteristics which yields a longer compressor lifetime. It is demonstrated that a key to the performance of the EEHP is the expansion pressure ratio. A larger expansion pressure ratio yields a higher improvement potential when compared with the VCHP.

In this paper, the linear nonequilibrium thermodynamic approach is used to analyze energy processes in the wind energy conversion system (WECS), with a directly connected vertical axis wind turbine (VAWT) and vector controlled permanent magnet synchronous generator (PMSG). Both elements are considered as linear universal energy converters (EC) linearized at the points of the given range of common to VAWT and PMSG angular velocity. The dependences on the angular velocity of the coupling coefficients between the ECs input and output and the dimensionless parameters of their operating modes were received. This allows for choosing the optimal points of ECs operation according to the specified criteria and obtaining indicators of their maximum efficiency. To assess the quality of the cascade connection of two ECs, the appropriate coefficient was introduced, the dimensionless parameters and characteristics of the equivalent EC were obtained, and the conditions of its maximum efficiency were determined. Analysis of the VAWT-PMSG connection quality showed reserves for improving WECS efficiency. The impact of VAWT and PMSG variable parameters on the quality of this connection is studied, and further research directions are shown. The proposed thermodynamic approach allows an effective search for solutions for the efficiency improvement of various systems with energy transfer and transformation.

Drag-dominant tidal turbine energy holds tremendous clean energy potential but faces significant hurdles as unsuitability of Disk Actuator theory due to the varying swept blockage area, unaccounted bypass flow downstream interaction and rotor parasitic drag whereas Blade Element Momentum theory is computably effective for majorly 3-blade lift-dominated aerofoil. This study proposes a novel method to find the optimal TSR of any turbine with a cost-effective and user-friendly Moment Balancing algorithm to support robust tidal energy development. Performance analysis CFD study of Pinwheel and Savonius tidal turbines was carried out. Dynamic TSR matrix was developed with varying rotational speeds and fluid velocities for reliability, unlike previous works simulated at a fixed fluid velocity. Novel parameters such as thrust and idle moment are introduced as functions of only inlet fluid velocity and rotational speed respectively. These relationships are verified through regression analysis, and the turbines' net moment equations are established based on these parameters. Rotational speed was a reliable predictor for Pinwheel's idle moment, while inlet velocity was a reliable predictor for thrust moment in both models. The optimal (Cp, TSR) values for Pinwheel and Savonius turbines were (2.37, 0.223) and (0.63, 0.16) respectively, within an acceptable error range for experimental validation.

Since Darwin’s “Power of movement in plants” the precise mechanism of oscillatory plant growth remains elusive. Hence the search continues for the hypothetical growth oscillator that regulates a huge range of growth phenomena ranging from circumnutation to pollen tube tip growth and stomatal movements. Oscillators are essentially simple devices with few components. A universal growth oscillator with only four major components became apparent recently with the discovery of a missing component, notably arabinogalactan glycoproteins (AGPs) that store dynamic Ca2+ at the cell surface. Demonstrably, auxin-activated proton pumps, AGPs, Ca2+ channels and auxin efflux “PIN” proteins, embedded in the plasma membrane, combine to generate cytosolic Ca2+ oscillations that ultimately regulate oscillatory growth: Hechtian adhesion of the plasma membrane to the cell wall and auxin-activated proton pumps trigger the release of dynamic Ca2+ stored in periplasmic AGP monolayers. These four major components represent a molecular PINball machine a strong visual metaphor that also recognizes auxin efflux “PIN” proteins as an essential component. Proton “pinballs” dissociate Ca2+ ions bound by paired glucuronic acid residues of AGP glycomodules, hence reassesses the role of proton pumps. It shifts the prevalent paradigm away from the recalcitrant “acid growth” theory that proposes direct action on cell wall properties, with an alternative explanation that connects proton pumps to Ca2+ signaling with dynamic Ca2+ storage by AGPs, auxin transport by auxin-efflux PIN proteins and Ca2+ channels. The extensive Ca2+ signalling literature of plants ignores arabinogalactan proteins (AGPs). Such scepticism leads us to reconsider the validity of the universal growth oscillator proposed here with some exceptions that involve marine plants and perhaps the most complex stress-test, stomatal regulation.

An area has been designated for demonstrating the utility of marine hydrokinetic turbines in Minas Passage, Bay of Fundy. Marine renewable energy may be useful for the transition from carbon-based energy sources but there is concern for the safety of fish that might encounter turbines. Acoustic receivers that detect signals from acoustically tagged fish that pass through the tidal demonstration area and detection efficiency of tag signals might be used to estimate the likelihood of fish encountering marine hydrokinetic turbines. The method requires that tagged fish passing through the development area will be reliably detected by a receiver array. The present research tests the reliability with which passing tags are detected by suspending tags beneath GPS-tracked drifters. Drifters carrying high residency Innovasea tags that transmitted every 2 seconds were usually detected by the receiver array even in fast currents during spring tides but pulse position modulation tags were inadequate. Sometimes very few high residency tag signals were detected when fast tidal currents swept a drifter through the receiver array, so increasing the transmission interval degrades performance at the tidal energy development area. High residency tags suspended close to the sea surface were slightly less likely to be detected if they passed by during calm conditions. Previously measured detection efficiencies were found to slightly overestimate the chances of a high residency tag carried by a drifter being detected as it passed by a receiver. This works elucidates the effectiveness with which acoustically tagged fish are detected in fast, highly turbulent tidal currents and informs the application of detection efficiency measurements to calculate the probability that fish encounter a marine hydrokinetic turbine.

Semidiurnal tidal currents can exceed 5 ms−1 in Minas Passage, Bay of Fundy, where a tidal energy demonstration area has been designated to generate electricity using marine hydrokinetic turbines. The risk of harmful fish-turbine interaction cannot be dismissed for either migratory or local fish populations. Individuals belonging to several fish populations have been acoustically-tagged and monitored by using acoustic receivers moored within Minas Passage. Detection efficiency ρ is required as the first step to estimate probability of fish-turbine encounter. Moored Innovasea HR2 receivers and high residency (HR) tags were used to obtain detection efficiency ρ as a function of range and current speed, for near-seafloor signal paths within the tidal energy development area. Strong tidal currents moved moorings so HR tag signals, and their reflections from the sea surface, were used to measure ranges from tags to receivers. HR2 self-signals that reflected off the sea surface showed which moorings were displaced to lower and higher levels on the seafloor. Some of the range testing paths had anomalously low ρ which might be attributed to variable bathymetry blocking the line of sight signal path. Clear and blocked signal paths accord with mooring levels. Application of ρ is demonstrated for calculation of abundance, effective detection range, and detection-positive intervals. High residency signals were better detected than pulse position modulation (PPM) signals. Providing the presently obtained ρ applies to tagged fish that swim higher in the water column, there is a reasonable prospect that probability of fish-turbine encounter can be estimated by monitoring fish that carry HR tags.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

pump as turbine (PAT); computational fluid dynamics; variable rotational nominal speed; OpenFoam.

Tidal stream energy is a renewable energy resource that might be developed to offset carbon emissions. A tidal energy demonstration (TED) area has been designated in Minas Passage, Bay of Fundy, for testing and installing marine hydrokinetic (MHK) turbines. Regulations require quantification of the potential for MHK turbine installations to harm local populations of marine animals. Here we use acoustic telemetry to quantify probability that post smolt Inner Bay of Fundy salmon encounter a turbine installation at the TED area. Previous work has quantified detection efficiency of Innovasea HR acoustic tags as a function of current speed and range from a moored HR2 receiver and also demonstrated that drifters carrying HR tags will be effectively detected when the drifter track crosses the array of HR2 receivers in Minas Passage. Salmon smolts were tagged and released in Gaspereau and Stewiacke Rivers, Nova Scotia, in order that the HR2 receiver array could monitor seaward migration of the post smolts through Minas Passage and particularly through the TED area. Presently we demonstrate methods by which tag signals detected by the HR2 array can be used to estimate the expected number of times that a post smolt would encounter a single near-surface MHK turbine installation during its seaward migration.

Green hydrogen is likely to play an important role in meeting the net zero targets of countries around the globe. Hence, producing green hydrogen cheaply and effectively is an important area of research. One potential option for green hydrogen production is to run electrolysers directly from offshore wind turbines, with no grid connection and hence no expensive cabling to shore. The removal of the grid presents an unusual integration challenge. The variable nature of wind turbines and farms results in a power output that can fluctuate more quickly than the electrolyser’s ability to respond without significantly stressing the electrolyser. Thus, the use of a battery, with the wind farm, becomes essential to even out some of the power variations that the electrolyser cannot deal with. In this work, a proof of concept of a wind farm control methodology designed to reduce variability in wind farm active power output is presented. Smoothing the power supplied by the wind farm to the battery reduces the size and number of battery charge cycles and helps to increase battery lifetime. Considering off-grid wind farms which exclusively power an electrolyser, this work quantifies the impact of the wind farm control method on battery lifetime for wind farms of 1, 4, 9 and 16 wind turbines. This is achieved using suitable wind farm, battery and electrolyser models. As an example, for the largest wind farm studied, consisting of 16 x 5 MW wind turbines, batteries with a lifetime of 15 years have approximately a 30 % reduction in required capacity (reduced from 14 MWh to 10 MWh) compared to operating without wind farm control. It is found that reducing the variability of the active power output of wind farms through the wind farm control methodology presented can have a significant impact on battery degradation and hence on battery lifetime. Hence, wind farm control can reduce the required battery capacity for a given lifetime or it can increase the lifetime of a given battery capacity. The work presented shows that wind farm control could play a critical role in reducing the levelised cost of green hydrogen produced from wind farms with no grid connection and paves the way for the design and testing of a full implementation of the wind farm control.

Broadband reverse saturable absorption is systematically investigated via Z-scan, transient absorption spectrum (TAS). The excited state absorption and negative refraction of Orange IV are observed in the Z-scan experiment at 532 nm. Meanwhile, two-photon induced excited-state absorption and pure two-photon absorption are observed at 600 nm and 700 nm with the pulse width of 190 fs, respectively. An ultrafast broadband absorption in visible wavelength region is observed via TAS. The different nonlinear absorption mechanism at multiple wavelengths is discussed and interpreted from the results of TAS. In addition, the ultrafast dynamics of negative refraction in the excited state of Orange IV is investigated via degenerate phase object pump probe, from which the weak long-lived excited state is extracted. All studies indicate that Orange IV has the potential to be further optimized into a superior broadband reverse saturable absorption material and also has certain reference significance for the study of optical nonlinearity in organic molecules containing azobenzene groups.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

Objectives: We aimed to clarify the endoscopic and clinicopathological features of raspberry-shaped gastric lesions (RSGLs) and to establish an endoscopic diagnostic algorithm for RSGLs. Methods: We collected RSGLs from an endoscopic database at our hospital between May 2009 and August 2021. All RSGLs were histopathologically classified and compared based on their endoscopic and clinicopathological characteristics. Results: Sixty-five RSGLs in 54 patients were classified into five histopathological types: gastric adenocarcinoma of foveolar type (GA-FV, n = 43), gastric adenocarcinoma of fundic-gland type (GA-FG, n = 2), gastric adenocarcinoma of fundic-gland mucosa type (GA-FGM, n = 4), hyperplastic polyp (HP, n = 12), and proton pump inhibitor-related lesion (PPI-L, n = 4). All RSGLs exhibited polygonal or curved marginal crypt epithelium (MCE). GA-FV lesions had homogenously reddish (95%) and irregular microvascular (MV) pattern (91%). GA-FG lesions were heterogeneously reddish with a submucosal tumor shape (100%) and had a regular MV pattern (50%). GA-FGM lesions were homogenously reddish (75%) and occasionally had a submucosal tumor shape (50%) with an irregular MV pattern (75%). HP and PPI-L were homogeneously reddish (93%), with linear or dotted MCE (81%) and a regular MV pattern (100%). Conclusion: Our diagnostic algorithm for RSGLs constructed using endoscopic features might be useful for the endoscopic differential diagnosis of RSGLs.

Considering the dynamic stall effects in engineering calculations is essential for correcting the aerodynamic loads acting on wind turbines, both during power production and stand-still cases, and impacts significantly the turbine aeroelastic stability. The employed dynamic stall model needs to be accurate and robust for a wide range of airfoils and range of angle of attack. The present studies are intended to demonstrate the performance of a recently implemented "IAG dynamic stall" model in a wind turbine design tool Bladed. The model is transformed from the indicial type of formulation into a state-space representation. The new model is validated against measurement data and other dynamic stall models in Bladed for various flow conditions and airfoils. It is demonstrated that the new model is able to reproduce the measured dynamic polar accurately without airfoil specific parameter calibration and has a superior performance compared to other models in Bladed.

We work within a Winterberg framework where space, i.e., the vacuum, consists of a two component superfluid/super-solid made up of a vast assembly (sea) of positive and negative mass Planck particles, called planckions. These material particles interact indirectly, and have very strong restoring forces keeping them a finite distance apart from each other within their respective species. Because of their mass compensating effect, the vacuum appears massless, charge-less, without pressure, net energy density or entropy. In addition, we consider two variable models, where, , is Newton’s constant, and, , increases with an increase in cosmological time. We argue that there are at least two competing models for the quantum vacuum within such a framework. The first follows a strict extension of Winterberg’s model. This leads to nonsensible results, if increases, going back in cosmological time, as the length scale inherent in such a model will not scale properly. The second model introduces a different length scale, which does scale properly, but keeps the mass of the Planck particle as, the Planck mass. Moreover we establish a connection between ordinary matter, dark matter, and dark energy, where all three mass densities within the Friedman equation must be interpreted as residual vacuum energies, which only surface, once aggregate matter has formed, at relatively low temperatures. The symmetry of the vacuum will be shown to be broken, because of the different scaling laws, beginning with the formation of elementary particles. Much like waves on an ocean where positive and negative planckion mass densities effectively cancel each other out and form a zero vacuum energy density/ zero vacuum pressure surface, these positive mass densities are very small perturbations (anomalies) about the mean. This greatly alleviates, i.e., minimizes the cosmological constant problem, a long standing problem associated with the vacuum.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

We present a new interpretation of the Higgs field as a composite particle made up of a positive, with, a negative mass Planck particle. According to the Winterberg hypothesis, space, i.e., the vacuum, consists of both positive and negative physical massive particles, which he called planckions, interacting through strong superfluid forces. In our composite model for the Higgs boson, there is an intrinsic length scale associated with the vacuum, different from the one introduced by Winterberg, where, when the vacuum is in a perfectly balanced state, the number density of positive Planck particles equals the number density of negative Planck particles. Due to the mass compensating effect, the vacuum thus appears massless, charge-less, without pressure, energy density, or entropy. However, a situation can arise where there is an effective mass density imbalance due to the two species of Planck particle not matching in terms of populations, within their respective excited energy states. This does not require the physical addition or removal of either positive or negative Planck particles, within a given region of space, as originally thought. Ordinary matter, dark matter, and dark energy can thus be given a new interpretation as residual vacuum energies within the context of a greater vacuum, where the populations of the positive and negative energy states exactly balance. In the present epoch, it is estimated that the dark energy number density imbalance amounts to, , per cubic meter, when cosmic distance scales in excess of, , are considered. Compared to a strictly balanced vacuum, where we estimate that the positive, and the negative Planck number density, is of the order, particles per cubic meter, the above is a very small perturbation. This slight imbalance, we argue, would dramatically alleviate, if not altogether eliminate, the long standing cosmological constant problem.

Artificial intelligence systems are increasingly becoming a component of security-critical applications. The protection of such systems from various types of destructive influences is thus a relevant area of research. The vast majority of previously published works are aimed at reducing vulnerability to certain types of disturbances or implementing certain resilience properties. At the same time, the authors either do not consider the concept of resilience as such, or their understanding varies greatly. This work presents a formalized definition of resilience and its characteristics for artificial intelligence systems from a systemic point of view. It systematizes ideas and approaches to building resilience to various types of disturbances. Taxonomy of resilience of artificial intelligence systems to destructive disturbances is proposed. Approaches and technologies for complex protection of intelligent systems, issues of their resource efficiency and other open research issues are considered. Approaches of resilience assessment for artificial intelligence system are also analyzed and recommendations are provided for their implementation.

This study investigates the power production and blade fatigue of a three-turbine array subjected to active yaw control (AYC) in full-wake and partial-wake configurations. A framework of two-way coupled large-eddy simulation (LES) and aeroelastic blade simulation is applied to simulate the atmospheric boundary-layer (ABL) flow through the turbine array and the structural responses of the turbine blades. Mean power outputs and blade fatigue loads are extracted from the simulation results. By exploring the feasible AYC decision space, we find that (a) in the full-wake configuration, the local power-optimal AYC strategy with positive yaw angles endures less flapwise blade fatigue and more edgewise blade fatigue than the global power-optimal strategy; (b) in the partial-wake configuration, applying positive AYC in certain inflow wind directions achieves higher optimal power gains than that in the full-wake scenario and reduces the blade fatigue from the non-yawed benchmark. Through a theoretical analysis based on the blade element momentum theory, we reveal that the aforementioned differences in flapwise blade fatigue between the positively and negatively yawed turbine are due to the differences in the azimuthal distributions of the local relative velocity on blade sections, resulting from the combined effects of vertical wind shear and blade rotation. Furthermore, the difference in the blade force between the positively and negatively yawed front-row turbine induces different wake velocity and turbulence distributions, causing different fatigue loads on the downwind turbine exposed to the wake.

In this contribution, we make an attempt to write a theoretical proposal for designing an eco friendly thermal power plant which runs with cold nuclear fusion technology at a temperature of (1500 to 2000) deg.C. In our recently published papers, we have proposed a clear cut mechanism for understanding and implementing cold nuclear fusion technique pertaining to fusion of hydrogen with metals of mass numbers starting from 50. In this context, we would like to stress the point that, fusion of hydrogen under controllable temperature and pressure can be understood as a phenomenon of fusing neutron to the nucleus of the base atom. Part of isotopic nuclear binding energy difference of final and base atomic nuclides can be seen in the form of safe thermal energy of the order of (1 to 3) MeV per atom against 200 MeV released in nuclear fission of one Uranium atom. Due to increased heaviness and weak interaction, sometimes fused neutron splits into proton and electron. Proton seems to be retained by the base atom’s nuclear core and electron seems to join with the electronic orbits of the base atom. In this way, increased mass of base atomic nuclide helps in eco friendly production of thermal energy in large quantity. For this purpose we consider Iron-56 as a fuel. In a simplified view, under strong nuclear attractive forces, Iron-56 absorbs hydrogen atom as a neutron and by emitting 1MeV equivalent thermal energy transforms to Iron-57. Thus, one gram of Iron-56 can generate 1000MJ of heat with 50% efficiency. In a shortcut approach, by bombarding powder and semi-liquid forms of Iron-56 with direct neutrons coming from neutron source, our proposal can be tried, understood and verified experimentally.

The hitologiy image of mouse xenograft of olfactory ensheating cells ( OECs) in to Albino Swiss Strain rats corticospinal tract lesion shows immunorejection after 10 days in grafted tissue . Moreover, the images of postoperative xenotransplanted OECs under daily subcutaneous injection of 100 ml of a dosage of 6 mg/kg/day avoid immunorejection in the misplace of GFP labeled transplanted OECs with the survival time of 4 weeks and there is no sign of inflammation. the result shows that the daily injection of 100ml diluted cyclosporine avoids immune attack and reduces inflammatory cells infiltrate in delayed CST ipsilateral rat model and also our study proved that stop of cyclosporine injection would not prevent DFR function and the regenerated fibers can still be visualised.

Hydrogen plays a key role in the transition to a carbon-free economy. One of the areas of hydrogen use is the substitution of hydrocarbon fuel in gas turbine engines and power plants. This review article discusses the features of hydrogen combustion and their influence on the characteristics of combustion chambers in comparison with methane. The paper presents both the results of a study of pure hydrogen or methane and methane-hydrogen mixtures with different hydrogen content. Among the main features, it is worth noting a smaller ignition delay time and higher laminar flame speed with a shift in its maximum value to a rich mixture, which significantly affects on flashback inside burners premixer, especially at elevated air temperatures. Another feature is the increased temperature of the flame, which can lead to an increase in the rate of nitrogen oxides formation. However, wider combustion concentration ranges contribute to the stable combustion of hydrogen at temperatures lower than those of methane. Along with this, it was shown that even at the same adiabatic temperature, more nitrogen oxides are formed in a hydrogen flame than in a methane flame, which indicates an additional mechanism for NOx formation in addition to the Zeldovich mechanism. The article also summarizes some of the results of a study on the effect of hydrogen on the occurrence of thermoacoustic instability, which depends on the initial nature of pulsations during methane combustion. The presented data will be useful both to engineers who are engaged in solving the problems of designing hydrogen combustion devices, and to scientists in this field of study.

Vacuum pump wear is the most prevalent failure mode of the IBA Synthera® automated radiochemistry system. Rebuilding or replacing the pump causes equipment downtime and increases the radiation exposure of the service personnel. We built a dedicated test device to assess new or rebuilt pumps prior to installation, thus reducing downtime and radiation exposure during repairs. The Testbed incorporates a microprocessor that actuates the pump, valves, pressure sensor, and communicates with the user through lights, buttons, and an alphanumeric screen. The Testbed increases productivity and safety in the radiochemistry laboratory.

Pump Sizing is the process of dimensional matching an impeller and stator to provide a satisfactory performance test result and good service life during the operation of progressive cavity pumps. In this process, historical data analysis and dimensional monitoring are done manually, consuming a large amount of man-hours and requiring a deep knowledge of progressive cavity pump behavior. This work presents the use of complex networks in the construction of a prototype to recommend interference during the Pump Sizing process in a Progressive Cavity Pump. For this, data from different expert applications were used in addition to individual control Excel spreadsheets to build the database used in the prototype. From the pre-processed data, complex network techniques and the Betweenness Centrality metric were used to calculate the degree of importance of each order confirmation, as well as to calculate the dimensionality of the rotors. The model was evaluated using the mean squared error (MSE), obtaining a MSE of 0.28 for the cases where there were recommendations for order confirmations. Based on the results obtained, it was realized that there is a similarity with the dimensional defined by design engineers during the Pump Sizing process.

A simple line of reasoning, based on the most fundamental concepts of thermodynamics, yields some intriguing results for a better understanding of the processes occurring in the observable Universe. Gravitational mass must be continuously generated within an expanding thermodynamic system for this system to remain closed. The Second Law is a direct consequence of this production of mass. Simple expressions for the entropy and temperature of the Universe were obtained and the results agree well with observable values. Furthermore, it is demonstrated that the conservation laws within the Universe are independent of its energy density. Based on the solution for the quantum state of the Universe, it is conjectured that the Second Law is incomplete and must be complemented to a conservation law, which takes into account the growth of the amount of information within the Universe. Once the Second Law is complemented to a conservation law, the importance of mass generation within the Universe becomes well pronounced – not only gravitational effects play the role of an organising force, but also the amount of mass within the Universe defines both the amount of information within the Universe and the level of the Universe’s complexity.

Micro turbojets are used for propelling radio-controlled aircraft, aerial targets and personal air vehicles. When compared to full-scale engines, they are characterized by relatively low efficiency and durability. In this context, the degraded performance of gas path components could lead to an unacceptable reduction in the overall engine performance. In this work, a data-driven model based on a conventional Artificial Neural Network (ANN) and an extreme learning machine (ELM) was used for estimating the performance degradation of the micro turbojet. The training datasets containing the performance data of the engine with degraded components were generated using the validated GSP model and the Monte Carlo approach. In particular, compressor and turbine performance degradation were simulated for three different flight regimes. It was confirmed that component degradation had a similar impact in flight than at sea level. Finally, the datasets were used in the training and testing process of the ELM algorithm with four different input vectors. Two vectors had an extensive number of virtual sensors, and the other two were reduced to just fuel flow and Exhaust Gas Temperature. Even with the small number of sensors, the high prediction accuracy of ELM was maintained for takeoff and cruise but was slightly worse for variable flight conditions.

COVID-19 and long COVID-19 vulnerabilities may be caused indirectly by albumin binding deficiency (ABD) which can be corrected by the correct administration of human serum albumin (HSA). The liver is the primary site of nutrient regulation and fluid volume maintenance, control of both is by changes to albumin concentration. In healthy subjects the HSA lymphatic nutrient pump (HSALNP) ensures continual pumping of nutrients from the liver are appropriately distributed to organs. Nutrients are delivered to cells according to the availability of binding to HSA. The HSALNP therefore maintains the correct nutrients and colloidal pressure balance in all tissues independently. In unhealthy tissues, following COVID-19 infection, the passage of HSA/nutrients through the interstitial spaces and lymph will be impeded. Fluid therapy into the periphery leads to dilution of essential nutrients attached to the protein-carriers such as albumin. The levels of albumin being charged by the liver with nutrients is critical in maintaining immune stability by maintaining nutrient support and colloidal pressure of cellular structures. The site of HSA binding by the liver is of great importance and direct infusion of albumin into the Hepatic Portal Vein is the most appropriate method of maintaining colloid pressure and cellular nutrient levels.

The present study explores the effect of using two porous deflectors on the performance of the Savonius wind turbine compared to only one porous deflector. The numerical simulation is performed to solve the unsteady Navier-Stokes equations using the SST k-

The power utility, Tanzania Electric Supply Company Limited (TANESCO) is faced with challenges of supplying adequate power to the ever-increasing demand. To this end, this paper explores the installed Ubungo Gas Power Plant (UGP II) located in Dar es Salaam to find means of utilizing it in co-generation method. The study embarked on detailed modelling of the system and run simulations which indicated that the co-generation can result to power generation efficiency increase between 10.42 to 50.92%. It is recommended to change the UGP II to exploit this co-generation method. Further, the study could be improved by including more parameters of the gas and steam plant and verify them experimentally.

In order to improve the operation performance of the multi-stage double-suction centrifugal pump and reduce the internal energy loss of the pump, this paper proposes a single-objective optimization design method based on non-hierarchical response surface model (RSM) and the multi-island genetic algorithm (MIGA). Nine parameters, such as the blade outlet width and blade wrap angle, were used as design variables, and the optimization objective was the efficiency under design conditions. In total, 149 sets of valid data were obtained under the latin hypercube sampling method (LHS), the corresponding thresholds were set for efficiency and head, and 99 sets of valid data were obtained. A cross-validation analysis of the sieved data was carried out based on non-hierarchical RSM, global optimization of the efficiency was carried out using MIGA, and numerical verification was carried out via CFD. The research results show that compared with hierarchical RSM, non-hierarchical RSM can approximate the nonlinear relationship between the objective function and the design variables with higher accuracy, and the model fitting R2 value was 0.919. The efficiency was improved by 3.717% after optimization. The overall prewhirl of the impeller inlet after optimization decreased, the internal speed of the volute significantly improved, the large-area vortex at the volute and the outlet pipe was eliminated, the impact loss at the volute separating tongue disappeared, and the overall hydraulic performance of the pump was improved. The total entropy output value of the optimized pump was reduced by 4.79 (W/K), mainly concentrated in the reduction in the entropy output value of the double volute, and the overall energy dissipation of the pump was reduced.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

Abstract Universities have the potential, and the responsibility, to take on more ecological and relational approaches to facilitating learning-based change in times of interconnected socio-ecological crises. Signs for a transition towards these more regenerative approaches of higher education (RHE) that include more place-based, ecological, and relational, ways of educating can already be found in niches across Europe (see for example the proliferation of education-based living labs, field labs, challenge labs). In this paper, the results of a podcast-based inquiry into the design practices and barriers of enacting such forms of RHE are shown. This study revealed seven educational practices that occurred across the innovation niches. It is important to note these practices are enacted in different ways, or are locally nested in unique expressions, For example, while the ‘practice’ of Cultivating Personal Transformations was represented across the included cases, the way these transformations were cultivated were unique expressions of each context. These RHE-design practices are derived from twenty-six narrative-based podcasts as interviews recorded in the April through June 2021 period. The resulting podcast (The Regenerative Education Podcast) was published on all major streaming platforms from October 2021 and included 21 participants active in Dutch Universities, 1 in Sweden, 1 in Germany, 1 in France, and 3 primarily online. Each episode engages with a leading practitioner, professor, teacher, and/or activist that is trying to connect their educational practice to making the world a more equitable, sustainable, and regenerative place. The episodes ranged from 30 to 70 minutes in total length and included both English (14) and Dutch (12) interviews. These episodes were analyzed through transition mapping a method based on story analysis and transition design. The results include seven design practices such as Cultivating Personal Transformations, Nurturing Ecosystems of Support, and Tackling Relevant and Urgent Transition Challenges, as well as a preliminary design tool that educational teams can use together with students and local agents in (re)designing their own RHE to connect their educational praxis with transition challenges.

Wind energy in Europe is aimed to grow at a steady, high pace, but opposition from residents to local wind farm plans is one of the obstacles to further growth. A large body of evidence shows that local populations want to be involved and respected for their concerns, but in practice this is a complex process that cannot be solved with simple measures such as financial compensation. The visual presence and the acoustic impact of a wind farm is an important concern for residents. Generally environmental noise management aims to reduce the exposure of the population, usually based on acoustics and restricted to a limited number of sources (such as transportation or industry) and sound descriptors (such as Lden). Individual perceptions are taken into account only at an aggregate, statistical level (such as percentage of exposed, annoyed or sleep-disturbed persons in the population). Individual perceptions and reactions to sound vary in intensity and over different dimensions (such as pleasure/fear or distraction). Sound level is in fact a weak predictor of the perceived health effects of sound. The positive or negative perception of and attitude to the source of the sound is a better predictor of its effects. This article aims to show how the two perspectives (based on acoustics and on perception) can lead to a combined approach in the management of a wind farm aimed to reduce annoyance, not primarily of sound level. An important aspect in this approach is what the sound means to people: is it associated with the experience of having no say in plans, does it lead to anxiety or worry, is it appropriate? The available knowledge will be applied to wind farm management: planning as well as operation.

Mycobacterium tuberculosis is a leading cause of human mortality worldwide and the emergence of drug-resistantstrains, demands the discovery of new classes of antimycobacterials that can be employed in the therapeutic pipeline. Previously, a secondary metabolite Chrysomycin A, isolated from Streptomyces sp. OA161 was shown to have potent bactericidal activity against drug-resistant clinical isolates of M. tuberculosis and different species of mycobacteria. The antibiotic inhibits the mycobacterial topoisomerase I and DNA gyrase leading to bacterial death, but the mechanisms that could cause resistance are currently unknown. To further understand the resistance mechanism, spontaneous resistance mutants were isolated and subjected to whole-genome sequencing. Mutation in a Tet^R family transcriptional regulator MSMEG_1380 was identified in the resistant isolates and was close to an operon encoding membrane protein MSMEG_1381 and MSMEG_1382. Sequence analysis and modeling studies indicated that they are components of the Mmp family of efflux pumps and over-expression of either the operon or individual genes conferred resistance to chrysomycin A, isoniazid, and ethambutol that are in TB therapy. Our study highlights the role of membrane transporter proteins in conferring multiple drug resistance and the utility of recombinant strains overexpressing membrane transporters in the drug screening pipeline.

Large structures such as wind turbines are subject to environmental factors and varying operational loads which may result in structural damage, making components of these large structures prone to performance and mechanical degradation. The use of high-definition optical vision sensors in digital image correlation (DIC) allow for the application of a non-destructive image registration technique in which it measures finite three-dimensional deformations on surfaces through correlations of a unique pattern or set of unique localized patterns. However, the physical placement of an artificial marker such as a unique speckled pattern on the surface of the structure is time-consuming and often impractical for large structures. Therefore, we propose a novel auto-mated methodology that searches and segments salient and unique regions of an image as well as for all subsequent images to assist in performing efficient displacement measurements for vibrational study and structural health monitoring purposes. Our algorithm is validated on a con-trolled set of images, as well as on a small structure and large real-world wind turbine, which suggests the algorithm’s efficacy without the use of artificial markers for large structural health monitoring.

This paper proposes and demonstrates, in full scale, a novel type of energy geostructure (“the Climate Road”) that combines a ground source heat pump (GSHP) with a sustainable urban drainage system (SUDS) by utilizing the gravel roadbed simultaneously as energy source and rainwater retarding basin. The Climate Road measures 50m x 8m x 1m (length, width, depth) and has 800 m of geothermal piping embedded in the roadbed, serving as the heat collector for a GSHP that supplies a nearby kindergarten with domestic hot water and space heating. Model analysis of operational data from 2018-2021 indicates sustainable annual heat production levels around 0.6 MWh per meter road, with a COP of 2.9-3.1. The continued infiltration of rainwater to the roadbed increases the amount of extractable heat by an estimated 17% compared to the case of zero infiltration. Using the developed model for scenario analysis we find that draining rainwater from three single family houses and storing 30% of the annual heating consumption in the roadbed, increases the predicted extractable energy by 56% compared to zero infiltration with no seasonal energy storage. The Climate Road is capable of supplying three single family houses with heating, cooling and rainwater management year-round.

The membrane potential or resting potential of the neuron has been the subject of many studies. Although this theory explains the generation and maintenance of the membrane potential by direct or even facilitated diffusion, there are too many contradictions to doubt that these forces are sufficient or even at work in a process whose initial conditions are of rare complexity. The aim of this article is to show that already in the past, a competing theory has been developed whose hypothesis seems more scientifically sound. To confirm this last theory, Hirohisa Tamagawa carried out an experiment of great simplicity which makes it possible to invalidate the current theory and to question the teaching and the knowledge in Biology and Biophysics.

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Following the principles of chemistry, electrostatics and geometry, it becomes clear that ion channels cannot function in this way. The ions channels cannot by their location have both a filter function and be ion concentrators, and the Na/K pump by its position in the membrane and by the proposed assumptions is not able to perform its regulatory function. The current model must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena opening new research perspectives.

As one of the representatives of emerging metallic transition metal dichalcogenides, niobium ditelluride (NbTe₂) has attracted intensive interest recently due to its distorted lattice structure and unique physical properties. Here, we report on the ultrafast carrier dynamics in NbTe₂ measured using time-resolved pump-probe transient reflection spectroscopy. A thickness-dependent carrier relaxation time is observed, exhibiting a clear increase in the fast and slow carrier decay rates for thin NbTe₂ flakes. In addition, pump power dependent measurements indicate that the carrier relaxation rates are power-independent, with the peak amplitude of the transient reflectivity increasing linearly with pump power. Isotropic relaxation dynamics in NbTe₂ is also verified by performing polarization-resolved pump-probe measurements. These results provide an insight into the light-matter interactions and charge carrier dynamics in NbTe₂ and will pave the way for its applications to photonic and optoelectronic devices.

Motivated for improving the efficiency and reliability of wind turbine energy conversion, this paper presents an advanced control design that enhances the power regulation efficiency and re-liability. The constrained behaviour of the wind turbine is taken into account, by using the barrier Lyapunov function in the analysis of the Lyapunov direct method. This, consequently, guarantees that the generated power remains within the desired bounds to satisfy the grid power demand. Moreover, a Nussbaum-type function is utilized in the control scheme, to cope with the unpre-dictable wind speed. This eliminates the need for accurate wind speed measurement or estimation. Furthermore, via properly designed adaptive laws, a robust actuator fault-tolerant capability is integrated into the scheme, handling the model uncertainty. Numerical simulations are performed on a high-fidelity wind turbine benchmark model, under different fault scenarios, to verify the effectiveness of the developed design. Also, a Monte-Carlo analysis is exploited for the evaluation of the reliability and robustness characteristics against the model-reality mismatch, measurement errors and disturbance effects.

The Virtual Blade Model (VBM) is the implementation of the Blade element model (BEM). This was done by coupling the Blade Element Momentum theory equations to simulate rotor operation with the Reynolds Averaged Navier-Stokes (RANS) equation to simulate rotor wake and the turbulent flow field around it. Exclusion of actual geometry of blades causes lower computational cost (about 10 to 100 times). Also, due to simplifications in the meshing procedure, VBM is easier to set up than the models that consider the actual geometry of blades. One of the main unaddressed limitations of the VBM code was the constraint of modeling up to ten rotor zones within one computational domain. This paper provides a detailed and well-documented general methodology to develop a virtual blade model for simulation of ten-plus turbines within one computational domain to remove the limitation of this widely used and robust code. It is strongly believed that the technical contribution of this paper, combined with the current sky-rocketing advancement of available computational resources and hardware, would open the gates to simulate various engineering problems in the field of aerospace, clean energy, and many more.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

Tomatoes, one of the most appreciated vegetables consumed, are crops well adapted for cultivation in arid and semi-arid conditions, the success of large yields is guaranteed by covering water consumption through irrigation. Solar Pumps - SP are driven by Photovoltaic Panels - PV (SPAPV), eliminating the dependence on electricity or diesel; they are environmentally friendly because they generate carbon-free electricity and the cost of operation and maintenance is lower. In order to preserve the water administered by drip to the tomato crop grown in solariums, mulching is used. In Husasău de Tinca, in the Crișurilor Plain, cultivation of tomato varieties without mulching (WM) and with mulching with black foil (MBF) were studied. To answer the question "How effective are water conservation measures in terms of energy independence?", two variants of SPAPVs, direct pumping (ADP) and storage tank (AST) were simulated. Considering the conditions in the solariums, tomato crops do not benefit from the contribution of precipitation, therefore it is proposed to determine the water consumption of tomatoes (ETRo), using the temperatures inside the solarium. In 2016, the average temperatures during the vegetation period were observed with an insurance of over 20 %, the irrigation norms were 6945.7 m3 ha-1, for the WM variant and 6594.0 m3 ha-1 for the MBF variant, respectively. Specific Investment (SI) is 214,795 Euro ha-1 in case of ADP and respectively 202,990 Euro ha-1 in case of ATS. The payback period (IPT) is between 2.68 years and 2.53 years for the ADP variant and between 1.63 years and 1.54 years for the ATS variant, respectively. The indications for water use and irrigation water use show that in the MBF variant the water administered by localized irrigation is better utilized than in the WM variant. In the conditions of Crișurilor Plain, the best solution for the distribution of water in solariums, with the help of SPAPVs is the mulching system of tomatoes grown in solariums (MBF) and the arrangement of the drip irrigation system with a water storage tank (ATS).

The generation and maintenance of membrane potential is a fundamental part of Membrane Pump Theory. One of the key points of this hypothesis is based on a natural or facilitated molecular diffusion through several types of ion channels and pumps like the Na/K ATPase. Chemistry, physics and especially electrochemistry, however, bring strong contradictions to this theoretical assumption. By respecting the principles of chemistry and electrostatics, it becomes obvious that this theoretical hypothesis cannot work. The ionic diffusion that would be at the origin of this potential cannot take place. Indeed, the topology and the forces involved definitively exclude the current model, which must absolutely be revised according to the current state of our knowledge and allow an advance in the understanding of the phenomena and open new research perspectives.

The pH-related metabolic paradigm has rapidly grown in cancer research and treatment. In this contribution, this recent oncological perspective has been laterally for the first time in order to integrate neurodegeneration within the energetics of the cancer acid-base conceptual frame. At all levels of study, molecular, biochemical, metabolic and clinical, the intimate nature of both processes appears to be opposite mechanisms occurring at the far ends of a physiopathological intracellular pH/extracellular pH (pHi/pHe) spectrum. This wide-ranged original approach now permits an increase in our understanding of these opposite processes, cancer and neurodegeneration, and, as a consequence, allows to propose new avenues of treatment based upon the intracellular and microenvironmental hydrogen ion dynamics regulating and deregulating the biochemistry and metabolism of both cancer and neural cells. Under the same perspective, the etiopathogenesis and special characteristics of multiple sclerosis (MS) becomes an excellent model for the study of neurodegenerative diseases and, utilizing this pioneering approach, we find that MS appears to be a metabolic disease even before an autoimmune one. Also within this paradigm, several important aspects of MS, from mitochondrial failure to microbiota functional abnormalities, are analyzed in depth.

We report on the application of time-resolved inline digital holography to study the nonlinear optical properties of quantum dots deposited onto the sample glass. Fresnel diffraction patterns of the probe pulse due to noncollinear degenerate phase modulation induced by the femtosecond pump pulse were extracted from the set of inline digital holograms and analyzed. Absolute values of the nonlinear refractive index of both sample glass substrate and the deposited layer of quantum dots were evaluated using the proposed technique. To characterize the inhomogeneous distribution of samples’ nonlinear optical properties we proposed to plot an optical nonlinearity map calculated as a local standard deviation of diffraction patterns intensity induced by noncollinear degenerate phase modulation.

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

Cryptococcus neoformans causes meningoencephalitis in immunocompromised individuals, which is treated with Fluconazole (FLC) monotherapy when resources are limited. This can lead to azole resistance, which can be mediated by overexpression of ABC transporters, a class of efflux pumps. ABC pump-mediated efflux of FLC is also augmented in 10-generation old C. neoformans cells. Here, we describe a new ABC transporter Afr3 (CNAG_06909), which is overexpressed in C. neoformans cells of advanced generational age, that accumulate during chronic infection. The delta-afr3 mutant strain showed higher FLC susceptibility by FLC E-Test strip testing and also by a killing test that measured survival after 3 h FLC exposure. Furthermore, delta-afr3 cells exhibited lower Rhodamine 6G efflux compared to the H99 wild type cells. Afr3 was expressed in the Saccharomyces cerevisiae AD-delta strain, which lacks several drug transporters, thus reducing background transport. The AD-delta + Afr3 strain demonstrated a higher efflux with both Rhodamine 6G and Nile Red, even though the FLC MICs were not changed. Characterization of the delta-afr3 mutant revealed unattenuated growth but a prolongation (22%) of the replicative life span. In addition, delta-afr3 exhibited decreased resistance to macrophage killing and attenuated virulence in the Galleria mellonella infection model. In summary, our data indicate that a novel ABC pump Afr3p, which is upregulated in C. neoformans cells of advanced age may contribute to their enhanced FLC tolerance, by promoting drug efflux. Lastly, its role in macrophage resistance may also contribute to the selection of older C. neoformans cells during chronic infection.

The aim of this work was to test polyamines as potential natural substrates of the Acinetobacter baumannii chlorhexidine efflux protein AceI using near-UV synchrotron radiation circular dichroism (SRCD) spectroscopy. The Gram-negative bacterium A. Baumannii is a leading cause of hospital-acquired infections and an important foodborne pathogen. A. Baumannii strains are becoming increasingly resistant to antimicrobial agents, including the synthetic antiseptic chlorhexidine. AceI was the founding member of the recently recognised PACE family of bacterial multidrug efflux proteins. Using the plasmid construct pTTQ18-aceI(His₆) containing the A. Baumannii aceI gene directly upstream from a His₆-tag coding sequence, expression of AceI(His₆) was amplified in E. coli BL21(DE3) cells. Near-UV (250-340 nm) SRCD measurements were performed on detergent-solubilised and purified AceI(His₆) at 20 °C. Sample and SRCD experimental conditions were identified that detected binding of the triamine spermidine to AceI(His₆). In a titration with spermidine (0-10 mM) this binding was saturable and fitting of the curve for the change in signal intensity produced an apparent binding affinity (K_D) of 3.97 +/- 0.45 mM. These SRCD results were the first experimental evidence obtained for polyamines as natural substrates of PACE proteins.

The main goal of this paper is to show that Bayesian optimization could be regarded as a general framework for the data driven modelling and solution of problems arising in water distribution systems. Hydraulic simulation, both scenario based, and Monte Carlo is a key tool in modelling in water distribution systems. The related optimization problems fall in a simulation/optimization framework in which objectives and constraints are often black-box. Bayesian Optimization (BO) is characterized by a surrogate model, usually a Gaussian process, but also a random forest and increasingly neural networks and an acquisition function which drives the search for new evaluation points. These modelling options make BO nonparametric, robust, flexible and sample efficient particularly suitable for simulation/optimization problems. A defining characteristic of BO is its versatility and flexibility, given for instance by different probabilistic models, in particular different kernels, different acquisition functions. These characteristics of the Bayesian optimization approach are exemplified by the two problems: cost/energy optimization in pump scheduling and optimal sensor placement for early detection on contaminant intrusion. Different surrogate models have been used both in explicit and implicit control schemes. Showing that BO can drive the process of learning control rules directly from operational data. BO can also be extended to multi-objective optimization. Two algorithms have been proposed for multi-objective detection problem using two different acquisition functions.

During operation, the support bracket is the main part to withstand the axial loads of the pumped storage unit. Moreover, the effects of axial loads including the hydraulic thrust of runner flow and the weight of runner body may cause the support bracket deformation and fatigue damage. For the safe and stable operation, the simulation of the axial force and the structural analysis of the support bracket of a pumped storage unit was carried out in this paper. The CFD simulation result has revealed the variation rule of the axial force in different operating conditions. Using ANSYS Mechanical, the static stresses and deformation of support bracket with axial loads were calculated. The results release the location and variations of maximum stress and maximum deformation caused by the axial loads. By comparing the predicted maximum axial force with the admission force calculated by the structural analysis, it is found that the axial force of the researched machine is within the safe range. This study provides the reference for the safety and stable operation of the pumped storage unit.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

In developing countries today, population growth and the penetration of higher standard of living appliances in homes has resulted in a rapidly increasing residential load. In South Africa, the recent rolling blackouts and electricity price increase only highlighted this reality calling for sustainable measures to reduce the overall consumption and peak load. The dawn of the smart grid concept, embedded systems and ICTs have paved the way to novel HEMS design. In this regard, the Internet of Things (IoT), an enabler for smart and efficient energy management systems is seeing increasing attention for optimizing HEMS design and mitigate its deployment cost constraints. In this work, we propose an IoT platform for residential energy management applications focusing on interoperability, low-cost, technology availability and scalability. We focus on the backend complexities of IoT Home Area Networks (HAN) using the OCF IoTivity-Lite middleware. To augment the quality, servicing and reduce cost and complexities, this work leverages open-source Cloud technologies from Back4App as BaaS to provide consumer and Utilities with a data communication platform within an experimental study illustrating time and space agnostic “mind-changing” energy feedback, Demand Response Management (DRM) and appliance operation control via a HEM App via an Android smartphone.

Wind technology is considered to be among the most promising types of renewable energy sources, and due to high oil prices and growing concerns about climate change and energy security, it has been the subject of extensive considerations in recent years, including questions related to the relative sustainability of electricity production when the manufacturing, assembly, transportation and dismantling processes of these facilities are taken into account. The present article evaluates the environmental impacts, carbon emissions and water consumption, derived from the production of electric energy of the Villonaco wind farm, located in Loja-Ecuador, during its entire life cycle, using the Life Cycle Analysis method. Finally, it is concluded that wind energy has greater environmental advantages, since it has lower values of carbon and water footprints than other energy sources. Additionally, with the techniques Cumulative Energy Demand and Energy Return on Investment, sustainability in the production of electricity from wind power in Ecuador is demonstrated; and, that due to issues of vulnerability to climate change, the diversification of its energy mix is essential considering the inclusion of non-conventional renewable sources such as solar or wind, this being the only way to reduce both the carbon footprint and the water supply power.

This study aimed to enhance a micro hydroelectric generator system driven by free-flow vortex and to compare efficiency of Propeller and Crossflow turbines. Series of turbines in each type were designed and tested at water-flowrate of 0.02 m3/s. The turbine housing has 1 meter in diameter and 0.5-meter height with 2 meters outlet drain at the bottom. The best efficiency extracted from Crossflow turbines with the same height (0.3 meter) but different in diameter (0.4, 0.5, 0.6, and 0.7 meter) and numbers of blade (12, 18, 24, 30, and 23) was from an 18 blades turbine at 23.01% of efficiency. The best efficiency extracted from Propeller turbines with 5 blades was from a 0.4-meter-high turbine with a diameter of 0.7 meter at 13.92% of efficiency. There were 12 Propeller turbines designed in this study. They were different in height (0.2, 0.3, and 0.4 meter) and, in each height, 0.4, 0.5, 0.6, and 0.7 of diameter was applied. The result revealed that Cross Flow turbine had more efficiency to the system than Propeller turbine (9.09%) at the water-flowrate of 0.02 m3/s

The previously developed models for fuel droplet heating and evaporation processes, mainly the Discrete Multi Component Model (DMCM), and Multi-Dimensional Quasi-Discrete Model (MDQDM) are investigated for the aerodynamic combustion simulation. The models have been recently improved, and generalised for a broad range of bio-fossil fuel blends so that the application areas are broadened with increased accuracy. The main distinctive features of these models are that they consider the impacts of species thermal conductivities and diffusivities within the droplets to account for the temperature gradient, transient diffusion of species and recirculation. A formulation of fuel surrogates is made, using the recently introduced model, referred to as ‘’Complex Fuel Surrogate Model (CFSM)’’ and analysing their heating, evaporation, and combustion characteristics. The CFSM is aimed to reduce the full composition of fuel to a much smaller number of components based on their mass fractions, and to formulate fuel surrogates. Such approach has provided a proof of concept with the implementation of the developed model into a commercial CFD code ANSYS-Fluent. A case study is made for the CFD modelling of gas-turbine engine using kerosene fuel surrogate. The surrogate is proposed using the CFSM. The model is implemented into ANSYS-Fluent via a user-defined function to provide the first full simulation of the combustion process. Detailed chemical mechanism is also implemented into ANSYS Chemkin for the combustion study.

The Betz limit sets a theoretical upper limit for the power production by turbines expressed as a maximum power coefficient of 16/27. Betz’s theory is accurate and it is based on the calculation of kinetic energy.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

Low pressure fluid transport (1) applications often require low and precise volumetric flow rates (2) including low leakage to reduce additional costly and complex sensors. A peristaltic pump de-sign (3) was realized, with the fluid’s flexible transport channel formed by a solid cavity and the wobbling plate comprising a rigid and a soft layer (4). In operation, the wobbling plate is driven externally by an electric motor, hence, the soft layer is contracted and unloaded (5) during pump-cycles transporting fluid from low to high pressure sides. A thorough characterization of the pump system is required to design and dimension the components of the peristaltic pump. To capture all these parameters and their dependencies on various operation-states, often complex and long-lasting dynamic 3D FE-simulations are required. We present, here, a holistic design methodology (6) including analytical as well as numerical calculations, and experimental valida-tions for a peristaltic pump with certain specifications of flow-rate range, maximum pressures, and temperatures. An experimental material selection process is established and material data of candidate materials (7) (liquid silicone rubber, acrylonitrile rubber, thermoplastic-elastomer) are directly applied to predict the required drive torque. For the prediction, a semi-physical, analyti-cal model was derived and validated by characterizing the pump prototype.

Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

Novel molecular pinball machines of the plasma membrane control cytosolic Ca²⁺ levels that regulate plant metabolism. [https://youtu.be/zABg7LiBk88] Essential components involve: 1. an auxin-activated proton pump; 2. arabinogalactan glycoproteins (AGPs); 3. Ca²⁺ channels; 4. auxin-efflux “PIN” proteins. Typical pinball machines release pinballs that trigger various sound and visual effects. However, in plants “proton pinballs” eject Ca²⁺ bound by paired glucuronic acid residues of numerous glycomodules in periplasmic AGP-Ca²⁺. Freed Ca²⁺ ions flow down the electrostatic gradient through open Ca²⁺ channels into the cytosol thus activating numerous Ca²⁺-dependent activities.Clearly cytosolic Ca²⁺ levels depend on activity of the proton pump, the state of Ca²⁺ channels and size of the periplasmic AGP-Ca²⁺ capacitor: Proton pump activation is a major regulatory focal point tightly controlled by the supply of auxin: auxin efflux carriers conveniently known as “PIN” proteins [null mutants are pin-shaped!] pump auxin from cell to cell. Mechanosensitive Ca²⁺ channels and their activation by reactive oxygen species (ROS) are yet another factor regulating cytosolic Ca²⁺.Cell expansion also triggers proton pump/pinball activity by mechanotransduction of wall stress via Hechtian adhesion thus forming a Hechtian oscillator that underlies cycles of wall plasticity and oscillatory growth.Finally, Ca²⁺ homeostasis of plants depends on cell surface external storage as source of dynamic Ca²⁺, unlike the internal ER storage source of animals where the added regulatory complexities ranging from vitamin D to parathormone contrast with the elegant simplicity of plant life. This paper summarises a sixty year Odyssey.

Double suction centrifugal pump installed along the Yellow River faces the serious sediment erosion due to the high sediment content which cause the poor operation efficiency of pump unit. The particle motion characteristics and erosion characteristics in the pump under different flow rates and different particle concentrations were numerically simulated based on the particle track model of solid-liquid two-phase flow. The results show that the flow rate has a significant effect on the particle tracks and the erosion caused by the particles in the impeller. The total erosion rate is positively correlated with the flow rate, and increases with the increase of flow rate. The vortex and secondary flow in the impeller have obvious influence on the particle trajectory, which increases the particle concentration at the trailing edge of the pressure surface and intensifies the impact erosion in this area. The particles carried by the vortex intensifies the local erosion. The particle concentration mainly affects the erosion rate, but has little effect on the erosion position. The in-fluence of flow rate on the pump erosion is greater than that of the particle properties. These results provide a reference for optimization of the design of anti-erosion blades of the double-suction pump and regulation-operation of pumping station.

Existing Reynolds Averaged Navier-Stokes based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this study, a novel framework based on computational fluids dynamics driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model.

This paper presents the super-twisting algorithm (STA) direct power control (DPC) scheme for the control of active and reactive powers of grid-connected DFIG. Simulations of 5 KW DFIG has been presented to validate the effectiveness and robustness of the proposed approach in the presence of uncertainties with respect to vector control (VC). The proposed controller schemes with fixed gains are effective in reducing the ripple of active and reactive powers, effectively suppress sliding-mode chattering and the effe This paper presents a comparative study of two approaches for the direct power control (DPC) of doubly-fed induction generator (DFIG) based on wind energy conversion system (WECS). Vector Control (VC) and Sliding Mode Control (SMC). The simulation results of the DFIG of 5 KW in the presence of various uncertainties were carried out to evaluate the capability and robustness of the proposed control scheme. The (SMC) strategy is the most appropriate scheme with the best combination such as reducing high powers ripple, diminishing steady-state error in addition to the fact that the impact of machine parameter variations does not change the system performance. cts of parametric uncertainties not affecting system performance.

Energy harvesting from wind turbines has been explored by researchers for more than a century from conventional turbines up to the latest bladeless turbines. Amongst these bladeless turbines, vortex bladeless wind turbine (VBT) harvests energy from oscillation of a turbine body. Due to the novelty of this science and the widespread researches around the world, one of the most important issues is to optimize and predict produced power. To enhance the produced output electrical power of VBT, the fluid-solid interactions (FSI) were analyzed to collect a dataset for predicting procedure. Long short-term memory (LSTM) method has been used to predict the produced power of VBT from the collected data. The reason of choosing LSTM from various artificial neural network methods is that the parameters of VBT study are all time- dependent and the LSTM is one of the most accruable algorithms for predicting time series data. In order to find the relationship between the parameter and the variables used in this research, a correlation matrix was presented. According to the value of 0.3 for the root mean square error (RMSE), a comparative analysis between the simulation results and its prediction shows that the LSTM method is very accurate for these types of research. Furthermore, the LSTM method has significantly reduced the computation time so that the prediction time of desired values has been reduced from an average of 2 and a half hours to two minutes. Also, one of the most important achievements of this study is to suggest a mathematical relation of VBT output power which helps to extend it in a different size of VBT with a high range of parameter variations.

The fault diagnosis of safety critical systems such as wind turbine installations includes extremely challenging aspects that motivate the research issues considered in this paper. In fact, the prompt detection and the reliable diagnosis of faults in their earlier occurrence represent the key point especially for offshore installations. For these plants, operation and maintenance procedures in harsh environments would inevitably increase the cost of the energy production. Therefore, this work investigates fault diagnosis solutions that are considered in a viable way and used as advanced techniques for condition monitoring of dynamic processes. To this end, the work proposes the design of fault diagnosis strategies that exploit the estimation of the fault by means of data--driven approaches. This solution leads to the development of effective methods allowing the management of partially unknown information of the system dynamics, while coping with measurement errors, the model--reality mismatch and other disturbance effects. In mode detail, the proposed data--driven methodologies exploit fuzzy systems and neural networks in order to estimate the nonlinear dynamic relations between the input and output measurements of the considered process and the faults. To this end, the fuzzy and neural network structures are integrated with auto--regressive with exogenous input descriptions, thus making them able to approximate unknown nonlinear dynamic functions with arbitrary degree of accuracy. Once these models are estimated from the input and output data measurement acquired from the considered dynamic process, the capabilities of their fault diagnosis capabilities are validated by using a high--fidelity benchmark that simulates the healthy and the faulty behaviour of a wind turbine system. Moreover, at this stage the benchmark is also useful to analyse the robustness and the reliability characteristics of the developed tools in the presence of model--reality mismatch and modelling error effects featured by the wind turbine simulator. On the other hand, a hardware--in--the--loop tool is finally implemented for testing and comparing the performance of the developed fault diagnosis strategies in a more realistic environment and with respect to different fault diagnosis approaches.

Abstract:Shown is the derivation of Lorentz-Einstein k-factor in SRT as an amplitude-term of oscillation-differential equations of second order.This case is shown for classical Lorentz-factor as solution of an equation for undamped oscillation as well as the developed theorem as a second solution for advanced SRT of fourth order with an equation for damped oscillation-states.This advanced term allows a calculation for any velocities by real rest mass

In this paper we compare using computational fluid dynamics the aerothermal performance of two candidate casing manifolds for supplying an impingement-actuated active tip clearance control system for an aero-engine high-pressure turbine. The two geometries are (a) single-entry: an annular manifold fed at one circumferential location; (b) multiple-entry: a casing manifold split into four annular sectors, each sector supplied separately from an annular ring main. Both the single-entry and multiple-entry systems analysed in this paper are idealised version of active clearance control systems in current production engines. Aerothermal performance is quantitatively assessed on the basis of the heat transfer coefficient distribution, driving temperature difference for heat transfer between the jet and casing wall, and total pressure loss within the high-pressure turbine active clearance control system. We predict that the mean heat transfer coefficient (defined with respect to the inlet temperature and local wall temperature) of the single-entry active clearance control system is 77% greater than the multiple-entry system; primarily because the coolant in the multiple-entry case picks up approximately 40 K of temperature from the ring main walls, and secondarily because the average jet Reynolds number of impingement holes in the single entry system is 1.2 times greater than in the multiple entry system. The multiple-entry system exhibits many local hot and cold spots, depending on the position of the transfer boxes, while the single-entry case has a more predictable aerothermal field across the system. The multiple-entry feed system uses an average of 20% of the total available pressure drop, while the feed system for the single-entry geometry uses only 2% of the total available pressure drop. From the aerothermal results of this computational study, and in consideration of holistic aero-engine design factors, we conclude that a single-entry system is closer to an optimal solution than a multiple-entry system.

The adoption of Pump as Turbines (PATs) both in small scale hydroelectric plants and water supply systems has brought different advantages, the most recognized being cost-effectiveness as compared to other hydroturbines. However, due to their lack of flow control ability, their intolerance to off-design operations constitutes one tough shortfall. Moreover, this technology’s newness leads to PAT flow dynamics still being ununderstood even to date. Therefore, this study intends to numerically investigate the mixed flow PAT’s pump mode flow dynamics for five operating conditions expanding from optimum (1QBEP) to deep part-load (0.41 QBEP) conditions. Moreover the effect of runner blade angle on the same has been investigated where three angles namely -2°, 0°, and 2° have been considered. PAT flow stability was found to deteriorate as the flow decreased, where associated pressure pulsation level worsened at different flow zones. In addition, the blade angle increase led correspondingly increasing flow unsteadiness and pressure pulsation levels, where the pulsation frequencies from rotor-stator interactions were dominant for most of flow zones. This study’s findings are of a crucial importance to both scientific and engineering communities as they contribute to thorough understanding of PAT flow dynamics.

This paper studied the combined influences of the hot streak and swirl on the cooling performances of the NASA C3X guide vane coated with or without TBCs. The results show that: (1) Even under uniform velocity inlet conditions, the hot streak core can be stretched as it impinges the leading edge which causes higher heat load on the suction side of the forward portion. (2) The swirl significantly affects circumferential and radial migration of the hot streak core in the NGV passage. On the passage inlet plane, positive swirl leads to a hotter tip region on the suction side. In comparison, negative swirl leads to a hotter hub region on the pressure side. (3) Under the influence of swirl, migration of coolant improve the coverage of film cooling close to the midspan, while in the regions close to the hub and tip end-wall, the overall cooling performance decrease simultaneously. (4) In the regions with enough internal cooling, the cooling effectiveness increment is always larger than that in other regions. Besides, the overall cooling effectiveness increment decreases on the region covered by film cooling for the coated vane, especially in the region with negative local heat flux.

Smart cities will have a strong impact on the future of renewable energies as terms like sustainability and energy saving will be more common. In this sense, both of wind and hydrokinetic compact-size turbines, can play an important role in urban communities by providing energy to nearby consumption points in an environmentally suitable way. This work presents the experimental evaluation for a vertical-axis turbine Darrieus type, operating in an open-field wind tunnel and a confined water channel. Power and characteristic curves have been obtained for all test conditions, also the effect of turbine blockage has been evaluated under blockage values ranging from 6.8% to 35%. The peak power coefficient for the confined flow condition reached a value of 0.31 which is 1.5 times higher than the peak one for the experimental open field condition at the same Reynolds number and a blockage of 20%. Finally, two blockage correction equations have been applied to the water channel tests, which gave values quite similar to the results obtained from the wind tunnel.

To investigate the optimum layouts of small vertical axis wind turbines, a two-dimensional analysis of dynamic fluid body interaction is performed via computational fluid dynamics for a rotor pair in various configurations. The rotational speed of each turbine rotor (diameter: D = 50 mm) varies based on the equation of motion. First, the dependence of rotor performance on the gap distance (gap) between two rotors is investigated. For parallel layouts, counter-down (CD) layouts with blades moving downwind in the gap region yield a higher mean power than counter-up (CU) layouts with blades moving upwind in the gap region. CD layouts with gap/D = 0.5–1.0 yield a maximum average power that is 23% higher than that of an isolated single rotor. Assuming isotropic bidirectional wind speed, co-rotating (CO) layouts with the same rotational direction are superior to the combination of CD and CU layouts regardless of the gap distance. For tandem layouts, the inverse-rotating configuration (IR) shows an earlier wake recovery than the CO configuration. For 16-wind-direction layouts, both the IR and CO configurations indicate similar power distribution at gap/D = 2.0. For the first time, this study demonstrates the phase synchronization of two rotors via numerical simulation.

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.

The European Union Green Deal aims at curbing planet-warming greenhouse gas emissions and introducing clean energy production. But to achieve energy efficiency, the opportunity cost of different energies must be assessed. In this article, we analyse two different systems for the treatment of wastewater that, at the same time, produce energy for its own operation. On the one hand, high-rate algal ponds system (HRAP) is considered; on the other hand, we study a conventional activated sludge system which uses photovoltaic power (AS+PV). This paper offers a viability analysis of both systems based on the capacity to satisfy their energetic consumption. In order to assess this viability, the probability of not achieving the energy consumption threshold at least one day is studied. The results point that the AS+PV system self-sufficiency is achieved using much lesser surfaces than those of HRAP system (for the former, less than 6.500 m2, for the latter 40.000 m2). However, the important AS capital cost makes still the HRAP system more economic, although storage provides a great advantage for using the AS+PV in locations where we have a lot of irradiance. This viability analysis, along with the opportunity cost analysis, will be used to assess these two projects devoted to the treatment of wastewater.

Amorphous chalcogenide (ChGs) glasses are intrinsically metastable, highly photosensitive, and therefore exhibit numerous lightinduced effects upon bandgap and sub-bandgap illumination. Depending on the pulse duration of the excitation laser, ChGs exhibit a series of lightinduced effects spanning over femtosecond to seconds time domain. For continuous wave illumination, the effects are dominantly metastable in terms of photodarkening (PD) and photobleaching (PB) that takes place via homopolar to heteropolar bond conversion. On the other hand, under nanosecond and ultrafast pulsed illumination, ChGs exhibit transient absorption (TA) that is instigated from the transient bonding rearrangements through self-trapped exciton recombination. In the first part of the review, we pay special attention to continuous wave lightinduced PD and PB, while in the second part we will focus on the TA and controlling such effects via internal and external parameters e.g., chemical composition, temperature, sample history etc.

Some wind farms have implemented automated camera\textendash based monitoring systems e.g. IdentiFlight to mitigate the impact of wind turbines on protected raptors. These systems have effectuated the collection of large amounts of data that can be used to describe flight behavior in a novel way. This data uniquely provides both flight trajectories and images of individual birds throughout their flight trajectories. The aim of this study was to evaluate how this unique data could be used to create a robust quantitative behavioral analysis, that could be used to identify risk prone flight behavior and avoidance behavior thereby in the future assess collision risk. This was attained through a case study at a wind farm on the Swedish island Gotland, where golden eagles (Aquila chrysaetos), white-tailed eagles (Haliaeetus albicilla), and red kites (Milvus milvus), were chosen as the selected bird species. The results demonstrate that flight trajectories and bird images can be used to identify high risk flight behavior and thereby also used to evaluate collision risk and avoidance behavior. This study presents a promising framework for future research, demonstrating how data from camera\textendash based monitoring systems can be utilized to quantitatively describe risk prone behavior and thereby assess collision risk and avoidance behavior.

Wind energy is becoming an essential source of power for countries which have the aim to reduce greenhouse gases emission and mitigate the effects of global warming. The Wind Turbines (WTs) installed around the globe is increasing significantly every year. The dramatic increase in wind power has encountered quite a few challenges, among which the major issues are availability and reliability. The unexpected failure in WTs Gearbox (GB) ultimately increases the Operation and Maintenance (O&M) cost. The identification of faults in the earlier stages before it turns to catastrophic damage to other components of WT is crucial. This research deals with the prediction of WT failures by using a Supervisory Control and Data Acquisition (SCADA) system. The main aim is to forecast the temperature of the WTs GB to predict the impending overheating of the GB at an early stage. The earlier prediction will help to optimize the maintenance period and to save maintenance expenses and, even more important, generate warnings in due time to avoid major damages or even technical disasters. In the proposed method we compared six different machine learning (ML) models based on error and accuracy of prediction. The bagging regressor is the best ML model, which results in the mean square error of 0.33 and R of 99.8 on training data. The bagging regressor is then used to predict the fault in the WT GB, which detected the anomalous behavior of WT GB 59 days earlier than the actual failure. This model also detects the extremely unusual behavior of the GB 9 days earlier than a complete failure.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Mobility as a Service (MaaS) is an innovative transport concept, anticipated to provide travelers with different kinds of travel services, more sustainable than a private car, in a simpler, packaged way. It combines different transport modes to offer a tailored mobility package, like a monthly mobile phone contract. The rapid development of intelligent transportation system and the shared economy has speeded up the development of MaaS in these years. In this paper, we aim at classifying the existing research on MaaS and the characteristics of MaaS into different categories, in order to answer the following questions after reviewing the existing literature: What is MaaS? Who are the main actors in MaaS? How can MaaS be implemented? Why should it be implemented? Where will MaaS end up in this wave of disruption? When we talk about MaaS, what are we focusing on? What is the future leading frequency of MaaS? Finally, based on the existing literature, we envision the leading future of MaaS.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

The structural and strength analysis of the material used to construct such an important engine element as the turbine is of great significance, both at the design stage as well as during tests and expertises related to emergency situations. Bearing in mind the conditions above mentioned, the paper presents the results of research on the chemical composition, morphology and phased structure of the metallic construction material used to produce the blades of the high and low pressure turbine of the RD-33 jet engine, which is the propulsion unit of the MiG-29 aircraft. The data obtained as a result of the material tests of the blades allowed, on the basis of the analysis of chemical composition and phased structure, to determine the grade of the alloy used to construct the tested elements of the jet engine turbine. The structural stability of the material was found to be lower in comparison with engine operating conditions, which manifested itself as a clear decrease in the resistance properties of the blade material. The results obtained can be used as a basis for analyzing the life span of an object or a selection of material replacements, which enable to produce the analyzed engine element.

Background: Drinking and smoking have economic consequences and are the main risk factors of mortality and morbidity. Disease-specific deaths attributable to using substances present the primary health indicator in this study. This analysis focuses on mortality in productive age, 15 to 64 years since those deaths are considered the highest economic burden. Method: In the analytical part, data from the Registry of deaths of the Czech Republic for 1994 to 2017 were used. The number of deaths attributable to smoking and drinking was calculated using attributable fractions, based on literature review. This research aimed to reveal the gender differences in deaths attributable to drinking and smoking, according to age, and the differences in deaths regarding smoking or drinking. Results: The mortality attributable to smoking and drinking differs across age groups and genders. The highest median share of tobacco-related deaths is in the age group, 60—64 years. The highest median share of alcoholic deaths is in the age group of 50—54 years. Conclusions: There are significant differences between genders in both, smoking and drinking. A prevention program should be targeted to different age groups.

The extracts from the aerial parts of Helianthus salicifolius A. Dietr and Helianthus tuberosus L. collected in June were obtained using carbon dioxide supercritical fluid extraction with water as co-solvent. The antimicrobial activity in vitro of these extracts were determined against the reference species of Gram-positive and Gram-negative bacteria as well as fungi, representing by the yeast species of Candida spp. The following parameters were estimated: minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) or minimum fungicidal concentration (MFC). Both extracts were found to possess antimicrobial activity with MIC = 0.62-5 mg mL-1 for bacteria and MIC = 5-10 mg mL-1 for yeasts, showing bactericidal (MBC/MIC = 2-4) or fungicidal effect (MFC/MIC = 1-2 ). The highest activity was observed against S. aureus ATCC 29213 (MIC = 0.62 mg mL-1 for H. salicifolius extract; MIC = 2.5 mg mL-1 for H. tuberosus extract). Bactericidal effect of both extracts against S. aureus ATCC 29213 was confirmed by time-kill assay. Higher antioxidant activity was found for H. tuberosus extract (EC50 = 0.332 mg mL-1) as compared to that of H. salicifolius (EC50 = 0.609 mg mL-1). The total polyphenol content (TPC) expressed as gallic acid equivalents (GAE) was 13.75 ± 0.50 mg GAE (g of H. salicifolius extract)-1 and 33.06 ± 0.80 mg GAE (g of H. tuberosus extract)-1. There was a correlation between the antioxidant potential of both extracts and TPC but not between antistaphylococcal activity and TPC. The obtained data suggest potential application of these extracts as the natural preparations with the biocidal activity, including those with antistaphylococcal activity. Besides, both extracts may be regarded as potential natural conservants in cosmetics as well as natural preservatives in food.

Many academics are critical of the current publishing system, but it is difficult to create a better alternative. This review relates to the Sciences and Social Sciences, and discusses the primary purpose of academic journals as providing a seal of approval for perceived quality, impact, significance, and importance. The key issues considered include the role of anonymous refereeing, continuous rather than discrete frequency of publications, avoidance of time wasting, and seeking adventure. Here we give recommendations about the organization of journal articles, the roles of associate editors and referees, measuring the time frame for refereeing submitted articles in days and weeks rather than months and years, encouraging open access internet publishing, emphasizing the continuity of publishing online, academic publishing as a continuous dynamic process, and how to improve research after publication. Citations and functions thereof, such as the journal impact factor and h-index, are the benchmark for evaluating the importance and impact of academic journals and published articles. Even in the very top journals, a high proportion of published articles are never cited, not even by the authors themselves. Top journal publications do not guarantee that published articles will make significant contributions, or that they will ever be highly cited. The COVID-19 world should encourage academics worldwide not only to rethink academic teaching, but also to re-evaluate key issues associated with academic journal publishing in the future.