This paper assesses the behaviour of active distribution networks with high penetration of renewable energy sources when the control is performed in a centralised manner. The control assets are the on-load tap changers of transformers at the primary substation, the reactive power injections of the renewable energy sources and the active and reactive power exchanged between adjacent feeders when they are interconnected through a DC link. A scaled-down distribution network is used as testbed to emulate the behaviour of an active distribution system with massive penetration of renewable energy resources. The laboratory testbed involves hardware devices, real-time control, and communication infrastructure. Several key performance indices are adopted to assess the effects of the different control actions on the system operation. The experimental results demonstrate that the combination of control actions enables the optimal integration of a massive penetration of renewable energy.

This paper considers a non-mixture cure model for right censored data. It utilizes the maximum likelihood method to estimate model parameters in the non-mixture cure model. The simulation study is based on Fréchet susceptible distribution to evaluate the performance of the method. Comparing with Weibull and exponentiated exponential distributions, the non-mixture Fréchet distribution is shown to be the best in modeling a real data on allogeneic marrow HLA-matched donors and ECOG phase III clinical trial e1684 data.

The battery energy storage systems (BESS) are most promising solution for increasing efficiency and flexibility of distribution networks (DNs) with significant penetration level of photovoltaic (PV) systems. There are various issues related to the optimal operation of DNs with integrated PV sys-tems and BESS that need to be addressed to maximize DN performance. This paper deals with the day-ahead optimal active-reactive power dispatching in unbalanced DNs with integrated sin-gle-phase PV generation and BESSs. The objectives are the minimization of cost for electricity, en-ergy losses in the DN and voltage unbalance at three-phase load buses by optimal managing of active and reactive power flows. To solve this highly constrained nonlinear optimization problem, a hybrid particle swarm optimization with sigmoid-based acceleration coefficients (PSOS) and cha-otic gravitational search algorithm (CGSA), called PSOS-CGSA algorithm, is proposed. A scenario based approach encompassing the Monte Carlo simulation (MCS) method with the simultaneous backward reduction algorithm is used for the probabilistic assessment of the uncertainty of PV generation and power of loads. The effectiveness of the proposed procedure is evaluated through the series test cases in a modified IEEE 13-bus feeder.

The transverse momentum distribution of J/ψ mesons produced in pp collisions at the center-of-mass energy 5 TeV, 7 TeV，and 13 TeV is described by the modified Hagedorn function which is based on the Tsallis function and Hagedorn function. The calculated results by the modified Hagedorn function are in accord with experimental data measured by the LHCb Collaboration at LHC. The related parameters are obtained and analyzed.

Quantum cryptography revolutionizes secure information transfer, providing defense against both quantum and classical computational attacks. The primary challenge in extending the reach of quantum communication comes from the exponential decay of signals over long distances. Addressing this challenge, we have developed Quantum-protected Control-based Key Distribution (QCKD), overcoming transmission range limitations by monitoring signal leakages and rendering leaked quantum states significantly non-orthogonal. This paper reports on the experiments with the QCKD, conducted over a 1,707 km fiber line. We demonstrate advancements in critical components of the protocol, showing its remarkable scalability and adaptability for extended distances and multi-user configurations.

Measurement-Device-Independent Quantum Key Distribution (MDI-QKD) is a two-photon protocol devised to eliminate eavesdropping attacks that interrogate or control the detector in realized quantum key distribution systems. In MDI-QKD, the measurements are carried out by an untrusted third party, and the measurement results are announced openly. Knowledge or control of the measurement results gives the third party no information about the secret key. Error-free implementation of the MDI-QKD protocol requires the crypto-communicating parties, Alice and Bob, to independently prepare and transmit single photons that are physically indistinguishable, with the possible exception of their polarization states. In this paper, we apply the formalism of quantum optics and Monte Carlo simulations to quantify the impact of small errors in wavelength, bandwidth, polarization and timing between Alice's photons and Bob's photons on the MDI-QKD quantum bit error rate (QBER). Using published single-photon source characteristics from two-photon interference experiments as a test case, our simulations predict that the finite tolerances of these sources contribute (4.04+/-20/N_sifted) to the QBER in an MDI-QKD implementation generating an N_sifted-bit sifted key.

Free-Living Amoebae (FLA) are widely distributed protozoa in both nature and artificial environments such as drinking water. Besides the ability of all FLA to transport various pathogenic microorganisms, certain species, Acanthamoeba spp. or Balamuthia mandrillaris, have intrinsic pathogenic abilities and cause severe cerebral infections. Previous work has shown an enrichment of FLA cysts in biofilm developed in upper levels of Drinking Water Storage Towers (DWST), suggesting that differences in densities of FLA cysts may play a role in their unequal distribution in the water column. To evaluate this hypothesis, a model of a water column was created for this study and used to analyze the vertical distribution of cysts of the FLA Acanthamoeba castellanii, Vermamoeba vermiformis and Balamuthia mandrillaris from 0 to 23 weeks. Interestingly, our data showed that the cysts of both A. castellanii and V. vermiformis were enriched in upper water levels during their aging. However, B. mandrillaris cysts were equally distributed in the water column during the entire study. These results showed that, besides the role of the water level variation in the DWST, some FLA cysts can become less dense during their aging, which contributes to their enrichment in upper water, and thus biofilm levels.

A numerical approach for generating a limited number of water demand scenarios and estimating their occurrence probabilities in a Water Distribution Network (WDN) is proposed. This approach makes use of the demand scaling laws in order to consider the natural variability and spatial correlation of nodal consumptions. The scaling laws are employed to determine the statistics of nodal consumption as a function of the number of users and the main statistical features of the unitary user's demand. Besides, consumption at each node is considered to follow a Gamma probability distribution. A high number of groups of cross-correlated demands, i.e., scenarios, for the entire network were generated using Latin Hypercube Sampling (LHS) and the numerical procedure proposed by Iman and Conover. The Kantorovich distance is used to reduce the number of scenarios and estimate their corresponding probabilities, while keeping the statistical information on nodal consumptions. By hydraulic simulation, the whole number of generated demand scenarios was used to obtain a corresponding number of pressure scenarios on which the same reduction procedure was applied. The probabilities of the reduced scenarios of pressure were compared with the corresponding probabilities of demand.

Capsicum annuum var. glabriusculum, is a variety of wild chili pepper belonging to the family Solanaceae and is considered as the origin for all cultivated chili species of the world. This species is an important genetic resource for agriculture and food, is widely distributed in northeastern Mexico in altitudes from 0 – 1200 m.a.s.l. This species grows mainly at low altitudes and its upper limit reaches 1000m., it prefers temperatures above 18.3^O C and its production and harvest may ocurr at two seasons, one during the beginning of the summer and the main one ocurring in the middle of the autumn in northeast México. It is estimated that the main production occurs in the state of Tamaulipas with 84 tons per year and is harvested from 23 municipalities. Concentration of capseicins and dihydrocapsaicine from wild populations may vary considerably from one location to another in the municipalities, ecotypes and diverse climatic conditions from this wide geographic zone. The high demands of wild chili as well as the variability on concentration of capseicins in fruits are considered as some of the main reasons why intensive cultivation of this species should be carried out in Northeastern Mexico.

Successive-addition-of-digits-of-a-number(SADN) refers to the process of adding up the digits of an integer number until a single digit is obtained. Concept of SADN has been occasionally identified but seldom employed in extensive mathematical applications. This paper discusses SADN and its properties in terms of addition, subtraction and multiplication. Further, the paper applies the multiplication-property of SADN to understand the distribution of prime numbers. For this purpose the paper introduces three series of numbers -S1, S3 and S5 series- into which all odd numbers can be placed, depending on their SADN and the rationale of such classification. Extending the analysis the paper explains how composite numbers of the S1 and S5 series can be derived. Based on this discussion it concludes that even as the concept of SADN is rather simple in its formulation and appears as an obvious truism but a profound analysis of the properties of SADN in terms of fundamental mathematical functions reveals that SADN holds a noteworthy position in number theory and may have significant implications for unfolding complex mathematical questions like understanding the distribution of prime numbers and Goldbach-problem.

Mercury contamination in the Amazon is a significant public health concern arising from both natural sources and intensive mining activities in the region. This metal is used to separate Au from sediments, forming an amalgam that facilitates the extraction of precious metals. Accordingly, this study aimed to address the following question: What is the impact of mining on mercury contamination in the animal and human populations of the Amazon? The overall objective of this study was to conduct a systematic review of the existing literature to identify gaps in geographic coverage and assess the impact of Hg contamination on human and animal populations in the Amazon region. Our hypothesis was that higher mercury concentrations in tissue samples would be found closer to the mining areas. We employed the PECO and PRISMA-ScR protocols to collect articles published between 2017 and 2023, selected based on criteria representing projected points on a map within the biogeographic boundaries of the Amazon. Mercury concentrations increase with trophic levels, reaching high values of 3.7 µg/g in the muscles of predatory fish and 34.9 µg/g in human hair. The average level of mercury in humans exceeds 6 µg/g, surpassing tolerance levels. Although mining regions show high concentrations of Hg, the highest incidence was observed among populations with fish-based diets. Research on fish is crucial for assessing the risk to human health, given that fish are the main source of protein in the region.

Aedes scapularis is a neotropical mosquito known to transmit pathogens of medical and veterinary importance. Its recent establishment in southeastern Florida has potential public health implications. We used an ecological niche modeling approach to predict the abiotic environmental suitability for Ae. scapularis across much of the Americas and Caribbean Islands. Georeferenced occurrence data obtained from the Global Biodiversity Inventory Facility and recent collection records of Ae. scapularis from southern Florida served as input for model calibration. Environmental layers included bioclimatic variables provided in 2000 to 2010 average Modern Era Retrospective-analysis for Research and Applications climatic (MERRAclim) data. Models were run in the software program Maxent. Isothermality values found often in costal environments contributed strongest to model performance. Model projections suggested areas predicted suitable for Ae. scapularis across portions of the Amazon Basin, the Yucatán Peninsula, the Florida Peninsula, and multiple Caribbean Islands. Additionally, model predictions suggested connectivity of highly suitable or relatively suitable environments spanning the United States Gulf Coast, which may facilitate geographic expansion of this species. At least sixteen Florida counties were predicted highly suitable for Ae. scapularis, suggesting vigilance is needed by vector control and public health agencies to recognize further spread of this vector.

Species distribution modeling (SDM) has come a long way since its inception. Starting as simple bioclimatic envelope models based on expert knowledge, species distribution models (SDMs) have evolved into complex and sophisticated models that incorporate multiple sources of data and machine learning algorithms. Today, SDMs play a crucial role in addressing pressing conservation and management issues, including the impacts of climate change on species ranges and the as-sessment of species vulnerability to extinction. In this article, we will embark on a journey through the history, present, and future of SDM, exploring its evolution from bioclimatic envelopes to machine learning. We will also provide practical tips on how to use SDMs effectively and discuss the exciting future developments in this field. Whether you are a seasoned SDM expert or new to this field, this article will provide valuable insights into the exciting world of SDM. By exploring the rich history and current state of the field, we hope to shed light on the tremendous potential of SDM for improving our understanding of the distribution of species in a changing world.

Spodoptera frugiperda is an invasive pest that has spread in various parts of the world. These pests have the ability to spread and adapt highly to new habitats. Until now, it is not known with certainty the distribution of these invasive pests in Eastern Indonesia, especially Bali and Nusa Tenggara. This study aims to map the spatial distribution and genetic distribution of S. frugiperda which damages maize in the areas of Bali and Nusa Tenggara. This research was conducted using a survey method from May to September 2022 covering the islands of Bali, Lombok, Sumbawa, Sumba, Flores, and Timor. The results showed that S. frugiperda had spread evenly in Bali and Nusa Tenggara. The results of PCR amplification in the COI gene from 9 sample isolates from all research locations showed the similarity of DNA bands leading to the Spodoptera frugiperda species with a banding pattern length of 683 – 697. These results indicated that the distribution of genetic variants of corn caterpillars in Bali, NTB, and NTT was confirmed as S. frugiperda species. However, the isolated gene S. frugiferda, which was shown by the alignment results of the sequences from Lombok, was confirmed as a different strain from strains from Bali, Sumba, Sumbawa, Flores, and Timor. This incident can be seen from the difference in the protein base composition of S. frugiperda from Bali, Sumba, Sumbawa, Timor, and Flores. The results of phylogenetic analysis in this study confirmed 3 clusters of the genetic closeness of S. frugiperda. Cluster-1 comes from the results of the search for specimens of JB FAW and KB FAW from Bali, SB FAW and SB FAW Sorghum from Sumba, SW FAW from Sumbawa, KP FAW from Timor, and FL FAW from Flores. Cluster-2 is an isolate outside of our species. Cluster-3 comes from the search for LT and LS FAW specimens from Lombok. The genetic distance between cluster-1 and cluster-3 is quite far, which is 0.20 mu.

. Background: regular exercise elicits adaptive changes from several organs and physiological processes, including erythrocyte properties. Methods: in a group of 79 subjects (62 men and 17 women; mean age 31.37 +/- 10.19 years) who trained several times a week as they practiced amateur sports, we evaluated the elongation index, marker of erythrocyte deformability, the red blood cell distribution width (RDW), indicator of erythrocyte anisocytosis, hematocrit, hemoglobin and the main erythrocyte indices (MCV, MCH, MCHC) in basal conditions. Results: in comparison with a group of healthy not trained volunteers, the values of the elongation index, and not the RDW, are increased and this datum is accompanied by an increase of MCV and MCHC, likely related to an increased presence of circulating young erythrocytes in trained subjects. We also divided the same group according to the median of the VO2max, observing that the subgroup above the median shows both an increase in the elongation index values and a decrease in MCH and MCHC. Conclusions: in trained subjects there is no correlation between the values of elongation index and the RDW, while of particular interest and of a certain complexity seem the interrelations among elongation index, RDW and the main erythrocyte indices.

Based on the analysis of the spatial distribution of uranium grade in 348 boreholes of a uranium deposit in Xinjiang, the enrichment and spatial variation of uranium ore in two stopes of the deposit are discussed by using multifractal theory. The distribution characteristics of uranium ore of the two stopes are studied by multifractal parameters: the scaling exponent of mass , the scaling exponent of each sub-set and its corresponding fractal dimension , the fractal dimension D0 and information dimension D1. The differences of uranium distribution in two stopes can be well quantified by multifractal spectrum and multifractal parameters( , , ).10m×10m is defined as a fence unit, and the window sizes are respectively set, the singularity exponent of the two stopes are calculated by this element concentration-area(C-A) method. The results show that the multifractal theory and model can organically combine spatial structure information, scale change information and anisotropy information to obtain low-grade and weak mineral resources information, and can effectively distinguish complex and superimposed anomalies. This will provide a basis for local concentration and spatial variation rules of uranium distribution and the design of the parameters of leaching uranium mining well site.

Minirhizotron tubes were installed to monitor root growth dynamics of mature Shiraz grapevines in a rootstock trial established in the hot climate Riverina region of New South Wales, Australia. The vertical root distribution and seasonal root growth dynamics of Shiraz on own-roots and Shiraz grafted on the rootstocks Ramsey, 140 Ruggeri and Schwarzmann was studied for five seasons across a seven-year period to a depth of 60 cm. New root production was significantly influenced by genotype, soil depth, season, growth stage and year. Soil moisture and soil tem-perature were monitored at 10, 30 and 60 cm in the last two seasons. Soil moisture at 30 cm and soil temperature at all three depths were significant predictors of root growth. New root numbers were significantly higher in 140 Ruggeri than the other rootstocks. To the depth studied, 140 Ruggeri roots were evenly distributed from the topsoil down, whereas the majority of roots of Schwarzmann and Shiraz were located at intermediate depths in the 10-40 cm ad 20-40 cm zones respectively, while Ramsey roots were found at 20 cm or below. Depending on genotype, root growth occurred across several phenological stages but tended to peak at flowering. In some years we observed root growth in early and late winter at rates exceeding that of autumn, and this was associated with warmer temperatures during this period. Overall, seasonal rooting dynamics were responsive to abiotic factors but dominated by genotype.

Keywords: Fatigue crack propagation; Welding residual stress; Plastic re-distribution; Stress ratio effect

The main objective of this study is to apply structural equation modeling with partial least squares and based on covariance to assess the satisfaction of residential electricity consumers. The methodology used compares the results of both structural equation models to indicate the model that best fits the problem of measuring the satisfaction of residential consumers of electricity concessionaires and licensees. The sample used in the survey contained questionnaire responses from 86.175 individuals considering the period from 2014 to 2018. The constructs evaluated were satisfaction, quality, value, loyalty, and trust. Confidence interval analysis shows that all weights are significant, demonstrating the importance of all the indicators that represent the constructs. The trust, quality, and value constructs can explain 74.4% of the variability of the satisfaction construct, so the explanatory capacity of this relationship is considered substantial. Finally, the evaluation of the performance of the service provided by the electric energy concessionaires/licensees, measured by customer satisfaction, allows for the continuous improvement of services and meeting, even if minimally, the expectations of its consumers.

This paper aims to provide an adaptation of the TL-moments method to censored data. The present study concentrates on Type-I censored data. The idea of using TL-moments with censored data may seem conflicting. But our perspective in that, we may use data censored from one side and trimmed from the other side. This study is applied to estimate the two unknown parameters of the Weibull distribution. The suggested point is compared with Direct L-moments and ML methods. A Monte Carlo simulation study is carried out to compare these method in terms of estimate average, root of mean square error (RMSE) and relative absolute biases (RAB).

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The degree of collaboration among supply chain partners and the structure of the network are important determinants of the level of satisfaction customers derive from the products or services. However, the effects of these dimensions on customer satisfaction at the downstream section of the supply chain remain under-researched in Nigeria. This study precisely examined the effects of collaboration and supply chain design on customers’ satisfaction at the downstream end of the chain using Ekiti State as study area. The study employed descriptive survey design with the use of structured Likert scale questionnaire administered to 381 retailers of noodles in Ekiti State. The research hypotheses were analysed using simple linear regression as statistical technique with the aid of SPSS version 22.0. At the end of the study, it was observed that both collaboration and supply chain design were significant predictors of customers’ satisfaction of instant noodles in Ekiti State. However, collaboration among supply chain partners emerged as stronger determinant of customers’ satisfaction than supply chain design. The study concludes that these two practices of supply chain management are highly important criteria any manufacturing firm especially in the noodles industry must pay close attention to in order to satisfy her consumers.

Inferring algorithmic structure in data is essential for discovering causal generative models. In this research, we present a quantum computing framework using the circuit model, for estimating algorithmic information metrics. The canonical computation model of the Turing machine is restricted in time and space resources, to make the target metrics computable under realistic assumptions. The universal prior distribution for the automata is obtained as a quantum superposition, which is further conditioned to estimate the metrics. Specific cases are explored where the quantum implementation offers polynomial advantage, in contrast to an indispensable exhaustive enumeration in the corresponding classical case. The unstructured output data and the computational irreducibility of Turing machines make this algorithm impossible to approximate using heuristics. Thus, exploring the space of program-output relations is one of the most promising problems for demonstrating quantum supremacy using Grover search that cannot be dequantized. Experimental use cases for quantum acceleration are developed for self-replicating programs and algorithmic complexity of short strings. With quantum computing hardware rapidly attaining technological maturity, we discuss how this framework will have significant advantage for various genomics applications in meta-biology, phylogenetic tree analysis, protein-protein interaction mapping and synthetic biology. This is the first time experimental algorithmic information theory is implemented using quantum computation. Our implementation on the Qiskit quantum programming platform is copy-left and can be found on https://github.com/Advanced-Research-Centre/QPULBA

Rural electrification rate (RER) in Africa is still low to date. Several countries in Sub-Saharan Africa have tried to address this problem using conventional single-phase two-wire or three-phase three-wire systems, however at large costs due to the nature of dispersed rural load centers, low load demand, and low population density. Another solution of off-grid generation creates associated health problems. Therefore, this paper undertakes a review of a single wire earth return (SWER) network as a RER improvement solution. The paper undertakes intensive literature review to elucidate challenges and solutions to the implementation of SWER technology. Advantages of SWER technology discussed make it the choice for RER improvement in Sub-Saharan African countries. After that, a case study is selected in rural Tanzania, and a preliminary SWER network design is undertaken.

Efficient and uninterrupted energy supply plays crucial role in the quality of the modern daily life, while it is obvious that the efficiency and performance of energy supply companies has significant impact on energy supply itself, and on determining and finetuning the future roadmap of the sector. In this study, the performance and efficiency of energy supply companies with respect to productivity is investigated over a case study of an electricity distribution company in Turkey. The factors affecting the company’s performance and their corresponding weights have been determined and elicited using analytical hierarchy process (AHP) and the Fuzzy AHP methods, as two well-known multi-criteria decision-making methods, which are two well-known prominent methods widely used in the literature. The results help demonstrate that the criteria elicited to evaluate the company’s energy supply performance plan a crucial role in developing strategies, policies and action plans to achieve continuous improvement and consistent development.

Staphylococcus aureus are commensal bacteria present on skin and mucosae in both humans and animals, but they can also be found in food, water and in various environments. They are also considered a major pathogen having a great morbidity leading to a wide range of infections. They are included in the list of most virulent and antimicrobic resistant bacterial pathogens (ESKAPE, Escherichia coli, Staphylococcus, Klebsiella pneumoniae, Acinetobacter baumannii, Pseudomonas aeruginosa, Enterococcus faecalis and faecium)) by the Center for Disease Control and Prevention (CDC), and S. aureus is part of the worldwide threat represented by the presence of antimicrobial resistance (AMR). The outcomes of an epidemiological investigation on 26,430 S. aureus isolates from a global public database (NPDIB; NCBI Pathogen Detection Isolate Browser) support the evidence of significant differences in the distribution of isolates and ARGs (Antimicrobial Resistance Genes) clusters among geographical areas of origin and among sources of the isolates. Moreover, the ARGs cluster patterns suggest an association between the isolates from human and animal populations. This outcome and the large diffusion of the pathogens among human and animal populations support the importance of gaining information on the epidemiology of these infections with a One Health approach.

In statistics and probability theory, one of the most important statistics is the sums of random variables. After introducing a probability distribution, determining the sum of n independent and identically distributed random variables is one of the interesting topics for authors. This paper presents the probability density functions for the sum of n independent and identically distributed random variables such as Shanker, Akash, Ishita, Pranav, Rani, and Ram Awadh. In order to determine all aforementioned distributions, the problem-solving methods are applied which is based on the change-of-variables technique.

This paper presents the development, comparison and analysis of several implementations of the B92 Quantum Key Distribution (QKD) protocol. In order to achieve this objective a prototype which consists of traditional (non-quantum) simulators was created, one for B92 protocol, one for B92 protocol with eavesdropper and one for B92 protocol with Quantum Bit Travel Time (QBTT) eavesdropper detection method. The principles of quantum mechanics were studied, as a foundation of quantum cryptography, for the realization of simulation programs that were written in C ++, focusing mainly on the B92 protocol and QBTT eavesdropper detection method. We compared the Quantum Bit Error Rate (QBER) for implementation of B92 protocol without eavesdropper, B92 protocol with eavesdropper and B92 protocol with QBTT eavesdropper detection method and found that QBTT eavesdropper detection method significantly reduces the QBER from the final key.

We analyzed the plant-litter-soil continuum to investigate the carbon and nitrogen distribution and ecological stoichiometry of an evergreen broad-leaved forest at Dagangshan Mountain, Jiangxi. The results showed that the average C and N contents and C:N ratios in the leaves and fine roots among 6 different tree species were 401.87g/kg, 21.41g/kg, 19.27 and 348.64g/kg, 15.73g/kg, 23.97, respectively; the average C and N contents and C:N ratios were 323.06 g/kg, 12.76 g/kg, 25.58 respectively in leaf litter, and 16.40 g/kg, 1.09 g/kg, 16.27 respectively for soil. In contrast with the C content, the total N content of the fine roots and litter had a high coefficient of variation and a high spatial heterogeneity. We ranked the six different representative tree species according to total C and N content in leaves and fine roots. The results for each species were generally consistent with each other, showing a positive correlation relationship between total C and N content in the leaves and roots. Among them, S. discolor (Champ. ex Benth.) Muell. plants displayed high carbon and nitrogen storage capacities, and on the other hand, C. fargesii Franch., C. myrsinifolia (Blume) Oersted, A. fortunei (Hemsl.) Makino, and V. fordii (Hemsl.) Airy Shaw showed a high nitrogen transfer rate. Total soil N and C decreased with depth. Soil organic carbon (SOC), soil resistant organic carbon (ROC), total N, alkali nitrogen, NH4+-N and NO3--N contents were all also negative correlated with soil depth, but the contents of the NH4+-N and NO3--N did not change significantly; The spatial distribution of soil NO3--N was significantly heterogeneous. At 0-10 cm soil depth, SOC was positively correlated with alkaline nitrogen, and at 10-20 cm soil depth, SOC was significantly positively correlated with total N. In general, when soil carbon was abundant, nitrogen supply capacity was also high.

As in any other plant, in the grapevine roots play a vital role in terms of anchorage, uptake of water and nutrients, as well as storage and production of chemicals. Their behaviour and development depend on various factors, namely rootstock genetics, soil physical and chemical features, field agronomic practices. Canopy management, involving techniques such as defoliation and pruning, could greatly influence root growth. To date, most of the studies on grapevine winter pruning have focused on the effects on yield and quality of grapes, achievable by using different pruning systems and techniques, while the knowledge of root distribution, development, and growth in relation to winter pruning is still not well understood. In this contest, the purpose of this study was to investigate the effect of winter pruning on the root system of field-grown Vitis vinifera cv. Pinot Gris grafted onto rootstock SO4. We compared two pruning treatments (pruning-P and no pruning-NP) and analysed the effect on root distribution and density, root index and on the root sugar reserves. Root data were analysed in relation to canopy growth and yield, to elucidate the effect of winter pruning on the root/yield ratio. Our data indicated that winter pruning stimulated the root growth and distribution without compromising canopy development, while no-pruning treatment produced less growth of roots but a larger canopy. Information regarding root growth and root canopy ratio is important as it gives us an understanding of the relationship between the aerial and subterranean parts of the plant, how they compete, and finally, offers us the possibility to ponder on cultural practices.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

The process of building microgrids on top of existing passive distribution networks warrants a multi-criteria analysis. Besides the calculation of investment outlays needed for the modernization of distribution networks, such an analysis covers an assessment of the technological and economic effects of building microgrids. The resulting effects depend on the topology and configuration of distribution networks, specific microgrid features, the choice of current type for the entire microgrid or its individual parts, the ways of connecting distributed energy resources (DER), the availability and condition of information and communications technology (ICT) infrastructure, and other factors. Complete input data allow one to design an optimal microgrid configuration, but the main technological and economic effects are determined by the algorithms of operation and the parameters setting of the automatic control system (ACS) and the protection system. Known approaches to designing microgrids focus on addressing basic tasks while minimizing investment required for their implementation. The above is fully justified when constructing new microgrids, but building microgrids on top of existing distribution networks, given the uniqueness of their topology and configuration, does not allow the use of standardized solutions. The development of approaches to the design of microgrids under such constraints, with minimized investment for the modernization of existing distribution networks, is an urgent task. The use of different types of current for microgrid segments determines the choice of particular ACS and protection system, which depends on the availability of information and communications technology infrastructure. This article contributes a review of approaches to designing AC and AC-DC microgrids to maximize their technological and economic effects. We review techniques for analyzing existing distribution networks aimed at choosing the type of current for the entire microgrid or its individual parts, the optimal connection points of microgrids to distribution networks, the mix and capacity of DERs, with such choices informed by the condition of switching devices and information and communications technology infrastructure. The article presents the results of the analysis of approaches to choosing the optimal configuration of microgrids, microgrid ACS and protection system, with an evaluation of the technological and economic effects subject to minimization of investment for the modernization of existing distribution networks.

The intercomparison among different atmospheric monitoring systems is key for instrument calibration and validation. Common cases involve satellites, radiosonde, radio occultation (e.g. GNSS-RO) and atmospheric model outputs (e.g. ERA5 reanalysis). Since instruments and/or measures are not perfectly collocated, the miss-collocation uncertainty must be considered in the related intercomparison uncertainty budgets.

Background: Acute pancreatitis is a common emergency. Morbidity control requires early detection of disease severity. METHODS: A total of 131 AP patients were analyzed retrospectively. Patients were divided into two groups mild AP (MAP: Ranson score <3) and severe AP (SAP: Ranson score ≥3), according to Ranson’s criteria. Demographic data, hospitalization duration, PNI, CRP, and RDW levels were compared. Any p-value below 0.05 (p<0.05) was accepted as statistically significant. RESULTS: Study included 67 (51.15%) males and 64 (48.85%) females. The age average was 59.74 (19-90) years. 95 (72.52%) patients had MAP, and 36 (27.48%) patients had SAP. Mean hospitalization time, PNI, and CRP differed significantly between the two groups (p=0.010, p<0.05, p<0.05, respectively). The RDW (p=0.380) level difference was insignificant. For SAP prediction; the sensitivity, specificity and cut-off value according to Ranson code cut-off point for PNI were determined as 80.0% (95% CI:54.8-85.8), %72.2 (95% CI:70.5-87.5) and ≤45.6 (gr/L) + (mm3), respectively, and 94.7% (95% CI:57.8-87.9), %75.0 (95% CI:88.1-98.3) and >105,1 mg/L, respectively for CRP. CONCLUSION: PNI and CRP values (but not RDW values) were compatible with the disease severity determined by the Ranson criteria.

Despite the continued growth of the sport, particularly among recreational athletes, very little is known about how triathletes prepare for an event. The aim of this study was to identify the training characteristics of recreational-level triathletes and assess how their preparation for a triathlon influences their health and fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after the event, ten (5 males, 5 females) recreational athletes completed a daily training log to provide information on every training session. In addition, participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Health Questionnaire weekly. Training loads were calculated using session-based rating of perceived exertion (sRPE) and training impulse (TRIMP). Every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. In the 6 weeks leading up to the event, training loads, total minutes trained, and time spent in each training zone did not differ significantly. Significant reductions in training duration (Z=2.39, p=0.017, ES = 0.90), training strain (Z=2.59, p=0.009, 0.98), and number of sessions (Z=2.49, p=0.012, ES = 0.94) were seen on week 6. Training intensity distribution favored a threshold approach with athletes spending 56% of their training time at zone 1, 40% at zone 2, and 4% at zone 3. No significant changes were seen in the DALDA or TDS questionnaires. The results show that while the training intensity distribution of recreational-level triathletes does not follow a polarized model, these athletes were able to maintain their health while preparing for an Olympic distance triathlon.

The Asian weaver ant (Oecophylla smaragdina) is a natural enemy, generalist predator of diverse major pest species (i.e. the highly destructive oriental fruit fly Bactrocera dorsalis) in economically strategic agricultural landscapes in Australia and Southeast Asia countries. For effective implementation of the weaver ant for biological control of the invasive bagworms Metisa plana, the dominant pest in the oil palm plantation, its distribution was investigated in Malaysia. From 2018-2022, censuses were first carried out to record Oecophylla colonies presence. Oecophylla colonies’ occupation patterns were monitored on 8 selected plantations. To distinguish between brood and barracks nests, 26 captured nests were evaluated to define the main predictor variable for its practical visual identification. More than 11000 palms with 10821 nests for over 500 colonies were sampled in this study. Results showed that O. smaragdina colonies distribution pattern exhibited three-dimensional ubiquitous occupation dominance. We also found that by observing the colony’s dense population spatial arrangements, it demonstrates them as spreading by waves featuring interconnected irregular geometrical patches shaped for each colony. The height to the ground nest location in palm canopies was the significant visual discriminant factor between Brood and barrack nests. Moreover, polydomous arboreal nesting behavior occupation occurred irrespective of palms or associated host plants sizes (≥ 3 m), throughout the year. However, colony nesting behaviors were polydomous and monodomous on shorter plants (≥ 2 m), while being strictly monodomous on small plants (≤ 1.5 m). Colonies occupied an average 3 to 4 palms yearly beginning from the newly founding phase up to the stable mature phase (3 to 4 years). Furthermore, we found that matured stable colonies (3 ≥ age ≥13) occupied 10-12 palms on average, on 800 m² to 2500 m² area delimited by a minimum average 20 m² of “no ants land” zone between each colony. Our results suggest that a sustained agriculture system in this area would be possible with the presence of matured colonies nests exploitation which could provide an efficient biological control ecosystem service.

Species distribution models have become tools of great importance in ecology since the advanced knowledge of suitable habitat of species is needed in the process of the world's biodiversity conservation. Models that use presence-only data are of great interests and are widely used in ecology due to their easy access. However, these models do not estimate accurately the true spatial species distribution based solely on presence-only data since they do not account for biases induced by the sampling techniques used and imperfect detection. To address this gap, Hierarchical integrated models have been recently introduced. Through this study, we assessed the relative performance of these new SDMs models using simulated data. The performance of the models was tested by comparing the estimates of parameters of the distribution models they provide with parameters used to simulate the distribution of the virtual species. The best model was the one whose estimates were close to the true distribution parameters of the virtual species. Results showed that analyzing Presence-only data in conjunction with Point-counts data through the Dorazio's Hierarchical model produced estimates of the coecients of the species intensity models with high precision and less bias while the Koshkina integrated model showed poor performance. Site-occupancy data, being not informative of species abundance, did not allow reducing biases in Presence-only data. The Dorazio's Hierarchical model produced estimates with high precision even with low detection probability. We have also found that the species rarity tends to in ate the variability of the models' estimates making modelling abundant species to be more accurate than modelling less abundant species. Hence, to model the species distribution with high precision based on Presence-only data, additional Point-counts data are required to account for sampling bias and imperfect detection.

The objective of this study is to examine a nonparametric estimate , using the kernel approach, of the conditional distribution function of a scalar response variable that is given a random variable whose values take place in a separable real Hilbert space. The observations will be dependent on one another in a quasi-associated fashion. The pointwise practically perfect consistencies with rates of this estimator are established by us under some broad conditions. The study’s major objective is to investigate the convergence rate of the proposed estimator and its application in the convergence rate and asymptotic normality of the hazard function. The asymptotic normality of the developed estimator is established precisely. Simulation studies were conducted to investigate the behavior of the asymptotic property in the context of finite sample data.

The weakness of the dispersion-managed link combined with optical phase conjugation to compensate for optical signal distortion caused by chromatic dispersion and nonlinear Kerr effect of standard single mode fiber is its limited structural flexibility. We propose dispersion map that can simultaneously compensate for the distorted wavelength division multiplexed signal while increasing the configurational flexibility. Each residual dispersion per span (RDPS) in the former half of the proposed link is randomly determined, and in the latter half, the arrangement order of RDPS is the same as or inverted in the former half. We confirm that the dispersion maps in which the RDPS distribution pattern in the latter half is opposite to the arrangement order in the former half are more effective in compensation, and rather, the compensation effect is better than in the dispersion map of the conventional scheme. The notable result of this paper is that the increase of flexibility can be achieved through random arrangement of RDPS in the former half, and the compensation improvement can be achieved by through inverse arrangement in the latter half which make the distribution profile of each half link roughly symmetric with respect to the midway optical phase conjugator.

Aiming at the current optimization problem of electric vehicle charging path planning, a charging path optimization strategy for electric vehicles under the "Traffic-Price-Distribution" mode is proposed. This strategy builds an electric vehicle charging and navigation system based on road traffic network model, real-time electricity price model and distribution network model. Based on Dijkstra shortest path algorithm and Monte Carlo time-space prediction method, the goal is to minimize the charging cost of electric vehicles. Optimal charging path. The simulation results of MATLAB and MATPOWER show that the electric vehicle charging path optimization strategy can better solve the local traffic congestion problem and improve the safety and stability of the distribution network on the basic of fully considering the convenience of electric vehicle charging.

The study delves into the critical examination of the Size of Loss distribution patterns in the context of auto insurance during pre- and post-pandemics, emphasizing their profound influence on insurance pricing and regulatory frameworks. Through a comprehensive analysis of the historical Size of Loss data, insurers and regulators gain essential insights into the probabilities and magnitudes of insurance claims, informing the determination of precise insurance premiums and the management of case reserving. This approach aids in fostering fair competition, ensuring equitable premium rates, and preventing discriminatory pricing practices, thereby promoting a balanced insurance landscape. The research further investigates the transformative impact of the COVID-19 pandemic on these Size of Loss patterns, given the substantial shifts in driving behaviors and risk landscapes. Also, the research contributes to the literature by addressing the need for more studies focusing on the implications of the COVID-19 pandemic on pre- and post-pandemic auto insurance loss patterns, thus offering a holistic perspective encompassing both insurance pricing and regulatory dimensions.

Generalized distributions have been studied a lot recently because of their flexibility and relia-bility in modeling lifetime data. The two-parameter exponentially-modified logistic distribution is a new flexible modified distribution that was introduced recently. It is regarded as a strong competitor for widely used classical symmetrical and non-symmetrical distributions such as normal, logistic, lognormal, and log-logistic. In this study, the unknown parameters of the dis-tribution are estimated using the maximum likelihood method. The Grey Wolf Optimization al-gorithm, which is a new meta-heuristic algorithm, is applied in order to solve the nonlinear like-lihood equations of the study model. The performance of the Grey Wolf Optimization method is compared to that of the other meta-heuristic algorithms used in this study, which include the Whale Optimization Algorithm, the Sine Cosine Algorithm, and the Particle Swarm Optimiza-tion Algorithm. The efficiencies of maximum likelihood estimates for all algorithms are com-pared via an extensive Monte-Carlo simulation study. The likelihood estimates for the location α and scale β parameters of the exponentially-modified logistic distribution developed with the Grey Wolf Optimization algorithm are the most efficient among others, according to simulation findings. Four real datasets are analyzed to show the flexibility of this distribution.

To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.

The distribution of noble metal nanoparticles in hydrogels are influencing their nanoplasmonic response and signal used for biosensor purposes. By controlling the particle distribution, it is possible to obtain new nanoplasmonic features with new sensing modalities. Particle distributions can be characterized by using volume-imaging methods such as the focused ion beam-scanning electron microscope (FIB-SEM) and the serial block-face scanning electron microscopy (SBFSEM) techniques . Since the pore structure of hydrogels is contained by the water absorbed in the polymer network it may pose challenges for volume-imaging based on electron microscope techniques since the sample must be in a vacuum chamber. The structure of hydrogels can be conserved by choosing appropriate preparation methods, which also depends on the composition of the hydrogel used. In this paper, we have prepared low-weight percentage hydrogels, with and without gold nanorods (GNR) for conventional SEM imaging by using two different drying techniques; (1) the critical point drying (CPD) technique and (2) hexamethyldisilazane (HMDS) drying of hydrogels. A qualitative characterization of the GNR-hydrogels was carried out to study the GNRs positioned in the polymer network. The effect of the two different drying methods on the hydrogel morphology were also compared. The use of HMDS as an alternative to the CPD has several advantages involving less parametrical variables for drying, involving less effort, being cost-effective, and requires no equipment use. In addition, choosing an optimized sample preparation method for SEM with optimized imaging parameters is highly important for obtaining accurate information about materials that is not correlated to artifacts. Hence, the results obtained from the preparation methods and SEM imaging parameters in this paper are useful for developing methods for mapping the metal particle distributions in micro-hydrogels by using FIB-SEM and SBFSEM techniques.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

This study presents an analysis of the spatial and temporal distribution of the two large destructive earthquakes that occurred in Lake Van area on October 23, and November 9, 2011, together with the azimuth-dependent distribution of the seismic activity and microseismicity clusters after the mainshocks, associated with the complex rupture processes of their aftershock sequence. The sequence began with the magnitude Mw 7.1 earthquake of 23 October and a second destructive earthquake of Mw 5.6. The aftershock sequences of the two mainshocks were linked to the local crustal faults beneath Lake Van area, followed successively and produced unusually intense activity and significant damage in the area. The main purposes of this study are to document the spatial and temporal distribution and evolution of the October 23, 2011 aftershock hypocenters and the azimuth-dependent distribution of seismic activity, and to understand the spatial and temporal character of the aftershock sequence using the distributional and evolutional patterns of the aftershock hypocenters. A total of 10,000 aftershocks were obtained from seismic data with a high signal-to-noise ratio over collected over three years from October 23, 2011 to March 2014. These aftershocks were plotted for the time periods from November 2011 through March 2012 to March 2014 and ≈ 5000 aftershocks were retained in the depth versus distance cross-sections to detect the clusters in the first step of study (November 2011–March 2012). The focal depth distribution of the aftershock clusters, the migration of hypocenter activity and microseismicity clusters were analyzed and the distributional patterns of the detected clusters were assessed using the geometric distribution of the aftershock hypocenters. The spatial and temporal distribution of aftershocks reveal interesting key features of the deep rupture complexity of the Van earthquake: (1) most prominent aftershocks have been located in the upper crust at depths shallower than 10 km beneath ruptured area, indicating that the upper crust is brittle and seismogenic; (2) two spatial clusters have been detected at 8-10 km depths and the upward extrapolation of these clusters intersects with faults; the main cluster (60 km wide) bounded by inferred reverse faults (f3 and f4) and the central cluster (25–30 km wide) bounded by faults (f1 and f2); (3) these spatial clusters form the largest volumetric pattern of the conical-shaped cluster at depths of about 25–30 km of the azimuth-dependent rotational projections, suggesting azimuthal distributions of deep rupture characteristics; and (4) the strongest temporal cluster of microseismicity derived from temporal distribution of aftershocks has been detected within an area of about 2.5–3.0 km² and it is spatially observed at 20 km depth within the central cluster, suggesting progressive failure of the adjacent patches of possible fault.

Generalized Bayes is a Bayesian approach based on the learning rate parameter η. In this study, we examine the effect of parameter η on the estimation results considering joint type-I and type-II hybrid censored samples from k exponential populations. In addition to the learning rate parameter, we consider two loss functions, the Linex and general entropy loss functions in the Bayesian approach. Monte Carlo simulations are performed to compare the performances of the estimation results under losses and different values of η. An illustrative example is performed to study the effect of the learning rate parameter and the different losses with different parameters.

The food distribution process is responsible for significant quality loss in perishable products. However, preserving quality is costly and consumes a tremendous amount of energy. To tackle the challenge of minimizing transportation costs and CO2 emissions while also maximizing product freshness, a novel multi-objective model is proposed. The model integrates a vehicle routing problem with temperature, shelf life, and energy consumption prediction models, thereby enhancing its accuracy. Non-dominated sorting genetic algorithm II is adapted to solve the proposed model for the set of Solomon test data. The conflicting nature of these objectives and the sensitivity of the model to shelf life and shipping container temperature settings are analyzed. The results show that optimizing freshness objective degrade the cost and the emission objectives, and the distribution of perishable foods are sensible to the shelf life of the perishable foods and temperature settings inside the container.

Recently, volatile organic compounds (VOCs) have been shown to act as precursors of secondary organic particles that react with ultraviolet rays in the atmosphere and contribute to photochemical smog, global warming, odor, and human health risks, highlighting the importance of VOC management. In this study, we measured VOC concentrations in various contexts including industrial and residential areas of Bucheon, Korea, through mobile laboratory and proton-transfer-reaction time-of-flight mass spectrometry methods to determine winter VOC concentrations, visualized the data based on spatial information, and used the results to develop an air quality management plan. For this purpose, global information system (GIS)-based air quality data and various environmental variables were comprehensively reviewed to assess spatial and temporal concentrations in three dimensions rather than in tables and graphs. Among VOCs, the levels of toluene, methanol, and n+i-butene were relatively high, with average concentrations of 48.3 ± 67.2, 34.4 ± 102.7, and 32.6 ± 57.7 ppb, respectively, at the end of the working day. The highest concentrations occurred near the Ojeong Industrial Complex. Mobile pollution sources are also a major driver of VOCs, highlighting the necessity of comprehensively reviewing traffic variables such as road level, estimated traffic volume, and average speed when identifying hotspots of air pollution. GIS-based visualization analysis techniques will improve the efficiency of air quality management.

We extend Ziv and Lempel's model of finite-state encoders to the realm of lossy compression of individual sequences. In particular, the model of the encoder includes a finite-state reconstruction codebook followed by an information lossless finite-state encoder that compresses the reconstruction codeword with no additional distortion. We first derive two different lower bounds to the compression ratio that depend on the number of states of the lossless encoder. Both bounds are asymptotically achievable by conceptually simple coding schemes. We then show that when the number of states of the lossless encoder is large enough in terms of the reconstruction block-length, the performance can be improved, sometimes significantly so. In particular, the improved performance is achievable using a random-coding ensemble that is universal, not only in terms of the source sequence, but also in terms of the distortion measure.

In the electric distribution systems, the “Smart Grid” concept is implemented to encourage energy savings and integration of the innovative technologies, helping the Distribution Network Operators (DNOs) in choosing the investment plans which to lead the optimal operation of the networks and increasing the energy efficiency. In this context, a new phase load balancing algorithm was proposed to be implemented in the low voltage distribution networks with hybrid structures of the consumption points (switchable and non-switchable consumers). It can work in both operation modes (on-line and off-line), uploading information from different databases of the DNO which contain: the consumers’ characteristics, the real loads of the consumers integrated into the Smart Metering System (SMS), and the typical load profiles for the consumers non-integrated in the SMS. The algorithm was tested in a real network, having a hybrid structure of the consumption points, on a time interval by 24 hours. The obtained results were analyzed and compared with other algorithms from the heuristic (Minimum Count of Loads Adjustment algorithm) and the metaheuristic (Particle Swarm Optimization and Genetic Algorithms) categories. The best performances were provided by the proposed algorithm, such that the unbalance coefficient resulted in the smallest value (1.0017). The phase load balancing led to the following technical effects: decreasing the average current in the neutral conductor with 94% and for the energy losses with 61.75 %, and increasing the minimum value of the phase voltage at the farthest pillar with the 7.14 %, compared to the unbalanced case.

Driven by industrialization and urbanization, urban air pollution can increase respiratory, heart, and cerebrovascular diseases, and thus mortality rates; as such, it is necessary to improve air quality through the consideration of individual pollutants and emissions sources. In South Korea, national and local governments have installed urban and roadside air quality monitoring systems. However, stations are lacking outside metropolitan regions, and roadside stations are sparsely distributed, limiting comparisons of pollutant concentrations with vehicle traffic and floating population levels. Local governments have begun using mobile laboratories (MLs) to supplement the fixed measurement network and investigate road pollution source characteristics based on their spatiotemporal distribution; however, the collected data cannot be used effectively if they are not visualized. Here, we propose a method to collect and visualize global information system (GIS)-based air quality data overlayed with environmental variables to support air quality management measures. Spatiotemporal analyses of ML-derived data from Bucheon, Korea, confirmed that particulate and gaseous pollutant concentrations were high during typical commuting hours, at intersections, and at a specially managed road. During commuting hours, the maximum PM10 concentration reached 200.7 µg/m³ in the Nae-dong, Gyeongin-ro, and Ojeong-dong ready-mix concrete complex areas, and the maximum PM_2.5 concentration was 161.7 µg/m³. The maximum NOx, NO₂, and NO levels of 1.34 ppm, 0.18 ppm, and 1.18 ppm, respectively, were also detected during commuting hours. These findings support the need for targeted management of air pollution in this region, and highlight the benefit of comprehensively comparing road levels, driving speed, and traffic levels when identifying hotspots of air pollution. Such analyses will contribute to the development of air quality management measures customized to regional characteristics.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Nature-Based Solutions (NBSs) can help to achieve multiple Water-Ecosystem-Food Nexus Do-main Objectives & Nexus Resilience Qualities, facilitating the transition to more resilient agrifood systems and providing an evidence base for a broader Nexus policy dialogue. This paper de-scribes the stepwise methodology developed in the EU-funded LENSES project to carry out a comprehensive analysis of NBSs in 6 pilot areas in 5 Mediterranean countries, and presents the results of NBSs implementation in 4 pilot areas, highlighting obstacles and opportunities. The methodology includes the development of an analytical evaluation framework and of a com-prehensive catalogue of Nexus-related NBSs, whose suitability needs to be assessed at the local level to achieve better use of protected/natural ecosystems, increase the sustainability and mul-tifunctionality of managed ecosystems and design and manage novel ecosystems. Subsequently, in a collective learning process which supported the operationalisation of the WEF Nexus, NBSs were identified that address specific contextual vulnerabilities, improve water distribution and enhance food security, while preserving ecosystems and supporting adaptation to climate change. The added value of the proposed methodology lies in the multi-stakeholder participatory approach to gain in-depth knowledge of local agri-food systems, including their main WEF-related challenges, and to facilitate overcoming barriers to NBS implementation.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

Deep Learning (DL) and Machine Learning (ML) are widely used in many fields, but rarely used in Frequency Estimation (FE) and Slope Estimation (SE) of signals. Frequency and slope estimation for Frequency-Modulated (FM) and single-tone sinusoidal signals are essential in various applications, such as wireless communications, sonar, and radar measurements. In this work, artificial neural network (ANN) and convolutional neural network (CNN) are used in frequency and slope estimation for FM signals under Additive White Gaussian Noise (AWGN) and Additive Symmetric alpha Stable Noise (SαSN). SαS distributions are impulsive noise disturbances found in many communication environments like marine systems; their distribution lacks a closed-form Probability Density Function (PDF), except for specific cases, and infinite second-order statistic, hence Geometric SNR (GSNR) is used in this work to determine the impulsiveness of noise in a mixture of Gaussian and SαS noise processes. ANN is a machine learning classifier, designed with few layers for reducing FE and SE complexity while getting higher accuracy as compared with classical techniques. CNN is a deep learning classifier, designed with many layers for FE and SE, and proved to be more accurate than ANN when dealing with big data and finding optimal features. Simulation results show that SαS noise can be much more harmful for FE and SE of FM signals than Gaussian noise. DL and ML can significantly reduce FE complexity, memory cost, and power consumption, which is important in many systems such as some Internet of Things (IoT) sensor applications. After training DCNN for frequency and slope estimation of LFM signals, the performance of DCNN (in terms of accuracy) can give acceptable results at very low signal-to-noise ratios where TFD fails, giving more than 20dB difference in the GSNR working range.

In order to achieve its carbon peak and neutrality targets, a high proportion of distributed power sources are connected to the distribution network in China, which greatly increases the risk of distribution network operation. Aiming at the above problems, this paper proposes an active distribution network risk planning model based on multi-source data from carbon capture and power internet of things, and conducts exceeding testing of distribution network based on the stochastic load flow algorithm with semi-invariant and level expansion, calculates the semi-invariant of each order of node state vectors and branch current vectors, and then utilizes the Gram-Charlier level expansion to obtain the exceeding probability density function and probability distribution function of the node voltages and line powers of the distribution network. The probability density function and probability distribution function of the exceeding are obtained using the Gram-Charlier series expansion. Combined with multi-source data, the active distribution network with integrated energy system considering carbon capture is modeled. According to the risk scenario of the distribution network, the nonconvex constraints in the model are simplified by the second-order cone relaxation, and the optimal planning scheme of the distribution network is solved by combining the gurobi solver with the risk index as the first-level objective and the economic benefit as the second-level objective. The simulation results of a coupled network consisting of a 39-node distribution network and an 11-node transportation network verify the effectiveness of the proposed model.

We present a novel passive satellite remote sensing approach for observing the three-dimensional distribution of aerosols emitted from wildfires. This method, called AEROS5P, retrieves vertical profiles of aerosol extinction from measurements of the TROPOMI satellite sensor onboard the Sentinel 5 Precursor mission. It uses a Tikhonov-Phillips regularization which iteratively fits cloud-free near-infrared and visible selected reflectances to simultaneously adjust the vertical distribution and abundance of aerosols. The information on the altitude of the aerosol layers is provided by TROPOMI measurements of the reflectance spectra at the oxygen A-band near 760 nm. In the present paper, we use this new approach for observing the daily evolution of the three-dimensional distribution of biomass burning aerosols emitted by Australian wildfires on 20-24 December 2019. Aerosol optical depths (AOD) derived by vertical integration of the aerosol extinction profiles retrieved by AEROS5P are compared with MODIS, VIIRS and AERONET coincident observations. They show a good agreement in the horizontal distribution of biomass burning aerosols, with a correlation coefficient of 0.86 and a mean absolute error of 0.2 with respect to VIIRS. A fair agreement is found between coincident transects of vertical profiles of biomass burning aerosols derived from AEROS5P and from the CALIOP spaceborne lidar. The mean altitude of these aerosols derived from these two measurements show a good agreement, with a small mean bias (185 m) and a correlation coefficient of 0.83. Moreover, AEROS5P observations reveal the height of injection of the biomass burning aerosols in 3D. The highest injection heights during the period of analysis are coincident with the largest fire radiative power derived from MODIS. Consistency is also found with respect to the vertical stability of the atmosphere.

In ore regions impacted by mining and metal smelting emissions, distinguishing between geogenic anoma-lies and anthropogenic contamination poses a significant challenge. In a study from two areas with different mining histories in the Ore Mountains, Czech Republic, we demonstrate that targeted sampling of topsoils and subsoils respecting local geology and correct soil data treatment respecting soil textural variability effects are indispensable to correctly construct and interpret geochemical maps and identify anthropogenic contam-ination by As, Cu, Pb, and Zn. The list of analysed elements must include both potentially toxic and lithogenic elements, otherwise natural controls of soil composition cannot be deciphered. By using empirical cumulative distribution functions, we found that local backgrounds for As/Fe and Pb/Ti are significantly naturally ele-vated (5.7 to 9.8 times and 2.1 to 2.7 times higher, respectively) compared to the global averages. We con-structed geochemical maps with topsoil minus subsoil concentrations to show the main directions of spreading anthropogenic contamination. The anthropogenic diffuse contamination contribution was calcu-lated (1.12·10-4 and 1.42·10-4 for As/Fe and 16.5·10-4 and 16.2·10-4 for Pb/Ti, respectively), which corresponds to topsoil enrichment by ca. 15 and 14 mg kg-1 for As and ca. 35 and 42 mg kg-1 for Pb in the two study areas. Our study thus provided the first published quantitative estimates of geogenic and anthropogenic contribution to this well-known montane area. The obtained estimates were comparable to the results obtained previously from the local peat archives. The approach we used is efficient in deciphering natural and anthropogenic controls of PTEs in geochemically complicated areas.

Conservation of tropical endemic amphibians largely suffers from Wallacean shortfall, a gap to which predictive species distribution models have contributed significantly to bridge by delineating probable distribution and the underlying suitable habitat within their distributional range. However, rarely is a prediction model ground-truthed to evaluate their predictive performance. Here we present a species distribution modeling approach using maximum entropy algorithm corrected for smaller sample size, in guiding explorative surveys aimed at optimizing survey effort and discovering unrecorded populations of Zhangixalus suffry, a rhacophorid tree-frog endemic to the northeastern part of the Indian subcontinent along with the factors limiting their distribution. With only 16 established historical locality data to model for (after spatial thinning to reduce autocorrelation) and a set of environmental predictors (climatic, topographic, and landscape composition), our model prediction enabled the successful discovery of seven new population records from unreported landscapes, extending its southernmost distributional limit over a considerable distance. The final composite distribution model combining all the locality records (n=23) predicted similar core areas of suitable habitat consistent with the known geographic distribution of the species but showed poor representation under existing coverage of Protected Area (PA) network in the Region with only 7% representation of suitable habitat under protection. Habitat suitability of a site was significantly governed by factors related to precipitation (precipitation seasonality and precipitation of the warmest quarter) and topographic factors that can influence it (elevation and aspect). This corroborates with the known ecology of Rhacophorid frogs, especially concerning their seasonal explosive reproductive strategy and foam nest-building behavior.Through this study, we propose explorative surveys guided by species distribution models to expedite unknown population discovery of rare, tropical endemic amphibians and using such taxa as surrogates in identifying conservation priority zones that can be directly applied to reserve design and conservation and management planning.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

Centrifugal pumps are widely employed in the oil refinery industry due to their efficiency and effectiveness in fluid transfer applications. The reliability of pumps plays a pivotal role in ensuring uninterrupted plant productivity and safe operations. Analysis of failure history data shows that bearings have been identified as critical components in oil refinery pump groups. However, traditional reliability estimation theories may not apply when data is limited or subject to right censoring. This paper addresses the complexity of estimating the Weibull distribution parameters using the maximum-likelihood method under the abovementioned conditions. The likelihood equation lacks an explicit analytical solution, necessitating the use of numerical methods for resolution. The proposed approach presented in this article leverages the Expectation-Maximization (EM) algorithm for estimating the Weibull distribution parameters. This method provides more accurate estimates of failure rates and probabilities by accounting for limited and censored data. The findings are demonstrated through a case study, showcasing the practical application of the proposed approach.

This research focuses on the customer orientation of insurance brokers, whose activity is regulated by the Law of 26/2006 of July 17 on the mediation of private insurances and reinsurances. The goal is to ascertain whether the intermediation inherent in the insurance broker’s activity, which implies a customer-oriented service, entails a positive behaviour that transcends the immediate environment, reaching society. This study presents a comparative analysis between the insurance brokerage society, characterised by providing a personalised customer service, and banks’ advisory services on insurance. To this end, we study the evolution of the total volume of business and new production, compared for a portfolio of insurance products. The results presented in this research suggest that the customer values the advisory service provided by the broker. However, for a particular business segment in standardised insurance products and products related to banking assets, customers are more likely to resort to the bank’s services. In addition, the results indicate that the commission percentages applied by the entities operating in the banking insurance channel exceed those perceived by the insurance broker. With all this, intermediation in the development of the insurer’s activity can entail an ethical and social behaviour that involves customer-orientation and, possibly, social service, which does not always benefit the insurer.

The average sizes \ {\bar{L}}_{i\ } and their dispersion W_i along the i-th axis of crystallites in powders are used to determine the X-ray diffraction sizes, D_{i\ XRD}, averaged over crystallite columns within the BWA method. Numerical calculations have been carried out for an orthorhombic lattice of crystallites, such as LiFePO4, NMC, having Lamé's g-type superellipsoid shape. For Lognormal distributions, the analytical expression for the normalized coefficient Kn is found and includes two constants. The first K_{g,0} is a constant at W→0, the second K_g is a constant depending on the g -type shape. The dependences of D_{i\ XRD} are also calculated for Normal distribution. A fairly simple equation can be obtained as a result of analytical transformations in the framework of experimentally validated approximations. However, a simpler way is to carry out numerical computer calculations with subsequent approximation of the calculated curves. Using the obtained analytical expressions to control technologies from nuclear fuel to cathode materials will improve the efficiency of flexible energy network especially storage in autonomous and standby power plants.

It has been well known that the exponential distribution is the only continuous distribution that has the memoryless property. Here, we observe that, if the exponential distribution dominates an economy as a probability distribution of income acquisition, then the memoryless property imposes equal opportunities on agents in this economy to acquire earnings. Based on this observation, we propose to identify the emergence of an exponential income distribution as a potential necessary condition for guaranteeing the equality of opportunity. Together with other conditions (such as social and economic mobility), it would promote equal opportunities for income acquisition among citizens. Empirically, we employ the latest data available from four representative market-economy countries (the United Kingdom, the United States, Canada, and China) to demonstrate that the exponential distribution is a stylized feature of the income structure of the low- and middle-income class, which occupies the great majority of populations. By contrast, the top income classes in these countries obey the Pareto distribution. To validate the relationship between exponential distribution and equal opportunity, we empirically show how the income structure of the low- and middle-income class in China (from 1978 to 2015) evolved towards an exponential distribution after the market-oriented economic reformation.

Glaucomatous optic neuropathy, a major cause of blindness, is characterized by the loss of retinal gan-glion cells (RGCs) and degeneration of their axons. Mitochondria are deeply involved in maintaining RGCs and their axons. Therefore, lots of attempts have been made to develop diagnostic tools and therapies tar-geting mitochondria. Recently, we reported that mitochondria are uniformly distributed in unmyelinated axons of RGCs, possibly owing to the ATP gradient. Thus, using transgenic mice expressing yellow fluo-rescent protein targeting mitochondria exclusively in RGCs within the retina, we assessed the alteration of mitochondrial distributions induced by optic nerve crush (ONC) via in vitro flat-mount retinal sections and in vivo fundus images captured through the cornea with a confocal scanning ophthalmoscope. We observed that the mitochondrial distribution in unmyelinated axons of RGCs that survived the ONC remained uni-form, although their density increased. Furthermore, via in vitro analysis, we discovered that the mitochon-drial size is attenuated following ONC. These results suggest that ONC induces mitochondrial fission without disrupting the uniform mitochondrial distribution. This mechanism may help to prevent axonal degeneration and apoptosis. The in vivo visualization system of axonal mitochondria in RGCs may be ap-plicable in the diagnosis of progression of optic neuropathy.

Recent studies on seafloor mapping have presented different modelling methods for the automatic classification of seafloor sediments. However, most of these studies have applied these models to seafloor data with appropriate number of ground-truth samples, which raises the question whether these methods are applicable to studies with smaller numbers of ground-truth data. In this study, we aim to address this issue by conducting sediment class-specific predictions using ensemble modelling to map areas with limited or without ground-truth data and combined with hydro-acoustic datasets. The resulting class-specific maps were then assembled into one map, where the most probable class was assigned to the appropriate location. Our approach was able to predict sediment classes without bias to the class with more ground-truth data and produced reliable seafloor sediment distributions maps that can be used for seafloor monitoring. Sediment shifts of a heterogenous seafloor in the Sylt Outer Reef, German North Sea were also assessed to understand the sediment dynamics in the area. The analyses of sediment shifts showed that the western area of the Sylt Outer Reef is highly active, and the results of the analyses assisted in providing recommendations on future seafloor monitoring activities.

The effects of environmental media on the corrosion fatigue fracture behavior of 25CrMo steel were investigated. The media include air, and a 3.5 wt.% and a 5.0 wt.% NaCl solutions. Experimental results indicate that the media induces the initiation of corrosion fatigue cracks at multiple sites. The multi-cracking sites cause the changes in the crack growth directions, the crack growth rate during the coupling action of the media and the stress amplitude. The coupling effects are important for engineering applications and research. The probability and predictions of the corrosion fatigue characteristic life can be estimated using the 3-parameter Weibull distribution function.

In China's mountainous coastal terrain, the storm badly damaged low-rise buildings. At present, it is not clear how the relative position of buildings and mountains affects the surface of a low-rise building’s fluctuating coefficient. The study compared these results with the wind pressure distribution without the surrounding environment. The primary objective of this study is to examine the fluctuating coefficient variation rule based on the spacing between hillsides and buildings under 0° wind angle. Additionally, the study analyzes the fluctuating wind pressure coefficient across wind angles between 0°~90°. The distribution of wind pressure in different common hillside landforms was examined through a wind tunnel experiment, which also compared with the distribution in an open environment. The study examined the fluctuating coefficient as the distance between the building and the hillside changed, specifically for wind blowing at a 0° angle. Next, an analysis is conducted on the changing pattern of the fluctuating coefficient for low-rise buildings ranging from a wind angle of 0° to 90°. Simultaneously, the investigation examined the power spectrum and wind pressure’s probability distribution, while considering the proximity of the building to an adjacent hill. The findings indicated that the changing wind pressure factor on the surface of the structure differed based on the relative location of the hillside and the building. The roof's wind pressure coefficient fluctuated and gradually increased until it reached its peak, unaffected by the surroundings. The low-frequency energy decreased in windward eaves, while the high-frequency energy progressively rose as the distance between the hillside and the building increased. The wind pressure on the leeward side exhibited Gaussian characteristics in its probability distribution.

This study has developed a Matlab application for simulating statistical models project (SMp) probabilistic distributions that are similar to binomial and Poisson, which were created by mathematical procedures. The simulated distributions are graphically compared with these popular distributions. The application allows to obtain many probabilistic distributions, and shows the trend (τ ) for n trials with success probability p, i.e. the maximum probability as τ=np. While the Poisson distribution PD(x;µ) is a unique probabilistic distribution, where PD=0 in x=+∞, the application simulates many SMp(x;µ,Xmax) distributions, where µ is the Poisson parameter and value of x with generally the maximum probability, and Xmax is the upper limit of x with SMp(x;µ,Xmax) ≥ 0 and limit of the stochastic region of a random discrete variable. It is shown that by simulation via, one can get many and better probabilistic distributions than by mathematical one.

This study has developed a Matlab application for simulating statistical models project (SMp) probabilistic distributions that are similar to binomial and Poisson, which were created by mathematical procedures. The simulated distributions are graphically compared with these legendary distributions. The application allows to obtain many probabilistic distributions, and shows the trend (τ ) for n trials with success probability p, i.e. the maximum probability as τ=np. While the Poisson distribution PD(x;µ) is a unique probabilistic distribution, where PD=0 in x=+∞, the application simulates many SMp(x;µ,Xmax) distributions, where µ is the Poisson parameter and value of x with generally the maximum probability, and Xmax is upper limit of x with SMp(x;µ,Xmax) ≥ 0 and limit of the stochastic region of the random discrete variable X. It is shown that by simulation via, one can get many and better probabilistic distributions than by mathematical one.

To enable the deployment of battery-electric vehicles (BEV) as passenger cars in the private transport sector, a suitable charging infrastructure is crucial. In this paper a methodology for efficient spatial distribution of charging infrastructure is evaluated by investigating a scenario with a market penetration of BEVs of 100 percent (around 1.3 million vehicles). It aims towards the development of various charging infrastructure scenarios - including public and private charging - which are suitable to cover the charging demand. Therefore, these scenarios are investigated in detail with focus on number of public charging points, their spatial distribution, the available charging power and the necessary capital costs. For the creation of those charging infrastructure scenarios a placement model is developed. It uses the data of a MATSim (Multi-Agent Transport Simulation) traffic simulation of the metropolitan area of Berlin to evaluate and optimize different distributions of charging infrastructure. The model uses a genetic algorithm and the principle of multi-objective optimization. The capital cost of the charging points and the mean detour car drivers must cover additionally are used as optimization criteria. Using these criteria should lead to cost efficient infrastructure solutions which provide high usability at the same time. The main advantage of the method selected is that multiple optimal solutions with different characteristics can be found and suitable solutions can be selected by using other criteria subsequently. The optimized charging infrastructure solutions show capital costs between 624 and 2950 million euro. Users must cover an additionally mean detour of 254m to 590m per charging process to reach an available charging point. According to the results a suitable ratio between charging points and vehicles is between 11:1 and 5:1. A share of fast charging infrastructure (&gt;50kW) of less than ten percent seems to be sufficient, if it is situated at main traffic routes and highly frequented places.

The philosophy of testing statistical hypothesis is a natural consequence and functional extension of mathematical analysis of Probability. Along with the concept of recurrence when applied to random sequences and functions, it leads to the analysis of a priori and posterior which implies testing statistical hypothesis. Testing statistical hypothesis also involves algebraic, functional and dimensional considerations, which are found in the works of Laplace. Aspects of mathematical analysis such as universality of solutions, Laws of Large Numbers, Entropy, Information, and various functional dependencies are the main factors explained in the five properties that lead to implication of testing statistical hypothesis. Various interesting examples with modern scientific significance from genetics, astrophysics, and other areas give methodological access to answers of different problems and phenomena which are involved in the logic of testing statistical hypothesis.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

In this paper, we will use the maximum likelihood estimation (MLE) and the Bayes methods to perform estimation procedures for the reliability of stress-strength ℜ=P[X>Y] based on independent adaptive progressive censored samples that were taken from the Chen distributions. An approximate confidence interval of ℜ is constructed using a variety of classical techniques, such as the normal approximation of the MLE, the normal approximation of the log-transformed MLE, and the percentile bootstrap (Boot-p) procedure. The Bayesian estimation of ℜ is obtained based on the balanced loss function, which comes in two versions here, the symmetric balanced squared error (BSE) loss function and the asymmetric balanced linear exponential (BLINEX) loss function. When estimating ℜ using the Bayesian approach, all the unknown parameters of the Chen distributions are assumed to be independently distributed and to have informative gamma priors. Further, a mixture of Gibbs sampling algorithm and Metropolis-Hastings algorithm is used to compute the Bayes estimate of ℜ and the associated highest posterior density credible interval. In the end, simulation research are used to assess the general overall performance of the proposed estimators and a real data set is provided to exemplify the theoretical results.

A comprehensive heuristic analysis of the Pollard's Rho Method (PRM) is given. The analysis is based on ultimate periods and tails distribution of sequences. If $n$ is the composite number to be factored, then an improved version of PRM is developed which has an expected run time of $O(\sqrt[8]{n}\ln n)$ on a multi-core architecture which utilized a clever way of evaluating polynomials.

This paper provides attempts to formalize Hayek’s theory of knowledge. It has been theoretically shown that exponential income distribution is a spontaneous order of the well-functioning market economy. We show that this theoretical result is supported by the empirical evidence from the United Kingdom and China. In particular, we empirically show how the income structure of China evolved towards an exponential distribution after the market-oriented economic reformation. Furthermore, we strictly prove that, if the income structure of an economy obeys an exponential distribution, the income summation over all households leads to an aggregate production function with Hicks-neutral-like technical progress, in which the technology factor is exactly equal to society’s information stock that is a result of combining all of decentralized decisions.

SStatistical characteristics of the wind speed in Samaria region of Israel have been analyzed by processing 11 years of wind data provided by the Israeli Meteorological Service, recorded at 10 m height above the ground. The cumulative mean wind speed at measurement height was shown to be 4.53 m/s with standard deviation of 2.32 m/s. Prevailing wind direction is shown to be char-acterized by cumulative mean azimuth of 226° with standard deviation of 79.76°. The results were extrapolated to 70-meter height in order to estimate wind characteristics at hub height of a me-dium-scale wind turbine. Moreover, Weibull distribution parameters were calculated annually, monthly and seasonally, demonstrating a good match with histogram-based statistical repre-sentations. Shape parameter of the Weibull distribution was shown to reside within a narrow range of 1.93 to 2.15, allowing us to assume a Rayleigh distribution, thus simplifying wind tur-bines energy yield calculations. The novelty of the current paper is related to gathering wind statistics for a certain area (Samaria) we are not aware of any published statistics regarding wind velocity and direction in this area. The data may be interesting for potential regional wind energy development in which the obtained Weibull distribution can be used in calculations of expected power generation of particular turbines with known power dependence on velocity. We also point out that the fact that realistic wind velocity statistics is well described by an analytic formula (Weibull distribution) is not trivial, and in fact the fit may have been poor.

We describe the development and validation of a HPLC-MS/MS method to assess the pharmacokinetics and tumour distribution of fenretinide, a synthetic retinoid chemically related to all-trans-retinoic acid, after administration of a novel oral nanoformulation of fenretinide, called bionanofenretinide (BNF). BNF was developed to overcome the major limitation of fenretinide: its poor aqueous solubility and bioavailability due to its hydrophobic nature. The method proved to be reproducible, precise, and highly accurate for the measurement of the drug and the mains metabolites. The lower limit of quantification resulted 1 ng/mL. The curve range of 1-500 ng/mL and 50-2000 ng/mL, for plasma and tumor homogenate respectively, was appropriate for the analysis, as demonstrated by the accuracy between 96.8% and 102.4% for plasma and 96.6-102.3% for tumor. The inter-days precision and accuracy determined on quality controls at 3 different levels were in ranges of 6.9%-7.5% and 99.3-101.0% and 0.96-1.91% and 102.3-105.8% for plasma and tumour, respectively.

Based on the engineering background of Daliuta mining area, the fracture distribution and water movement within the weakly cemented overlay strata are studied through liquid-solid coupling physical simulation and COMSOL numerical simulation test. 3D fracture network of overburden strata in mining is plotted based on the result of the physical simulation test. The results showed that the ‘fractured zone’ of the weakly cemented overburden strata in the western area develops more evidently than that in the eastern area ---- wide-opened fractures form at both ends of the working area and this leads to a wide distribution of fractures in the overlying strata.After the initial caving of the roof, height of the penetrating fractures increases rapidly and the separated strata space becomes the main channel for water flow. Under the action of water flow and rock strata movement, mining-induced fractures in overlying rock display cyclic change of expansion, penetration and closure. When the working face is fully mined, the penetrating fractures in the overlying strata and mining-induced fractures up in the working face become the main passages for water flow. The experimental result provides a reference for underground reservoirs layout and maintenance and water-conserved mining in western China.

While lidar-based forest inventory methods have been widely demonstrated, prediction of tree diameters with lidar is not well understood. The performance metrics typically used in studies for prediction of diameters can be difficult to interpret and may not support comparative inferences between sampling designs or study areas. We evaluate a variety of lidar and k nearest neighbor (k-NN) strategies for prediction of tree diameter distributions using two indices which are easier to interpret and compare. The indices are based on the coefficient of determination (R²), and root mean square deviation (RMSD). These indices facilitate comparisons with alternative (non-lidar) inventory strategies, and with other project areas. We evaluate k nearest neighbors (k-NN) dbh density (relative frequency by dbh class) prediction strategies with lidar for 190 training plots distribute across the 800 km² Savannah River Site in South Carolina, USA. We evaluate the performance of k-NN with respect to distance metrics, number of neighbors, predictor sets, and response sets. Amongst the examined strategies we found Mahalanobis distance with k = 3 neighbors performed best according to a number of criteria.

This work presents a new algorithm to resolve the problem of distribution network reconfiguration using the Tabu Search metaheuristic and voltage drop. The proposed method presents a different way to obtain the initial solution using the voltage drop, as well as a new way to generate a neighborhood of candidate solutions, based on randomness and the voltage drop, to perform a smooth and steady descent execution of the algorithm. The proposed algorithm has the main objective to reduce the active power losses in distribution networks, but it also achieves an refinement in the voltage profile. The proposed method was tested in two distribution systems, the 33-Bus and 94-Bus systems, commonly found and tested in the literature. The results of the tests show that the proposed method presents a low computational cost, achieves good solutions, and is better than the other methods found in the literature.

The increasing demand for higher inclusion cleanliness levels motivates the control over the formation and evolution of inclusions in the steel production process. In this work, the evolution of the chemical composition and size distribution of inclusions throughout a slab production process of Al-killed steel, including ladle furnace (LF) treatment and continuous casting (CC), was followed. The initial solid Al2O3 and Al2O3-MgO inclusions were modified to liquid Al2O3-CaO-MgO inclusions during LF treatment. The evolution of the size distributions during LF treatment was associated with the growth and removal of inclusions, as new inclusions were not created after the deoxidation process, according to a population density function (PDF) analysis. Additionally, the size distributions tended to be similar as the LF treatment progressed regardless of their initial features, whereas they differed during CC. Analysis of the upper tails of the distributions through generalized extreme values theory showed that inclusion distributions shifted from larger to smaller sizes as the process progressed. There were great changes in the distributions of large inclusions throughout the LF treatment and between the end of the LF treatment and the start of the CC process. Additionally, distributions of large inclusions differed at the end of the LF treatment, whereas such differences decreased as CC progressed.

It is quite easy to stochastically distort an original count variable to obtain a new count variable with relatively more variability than in the original variable. Many popular overdispersion models (variance greater than mean) can indeed be obtained by mixtures, compounding or randomlystopped sums. There is no analogous stochastic mechanism for the construction of underdispersed count variables (variance less than mean), starting from an original count distribution of interest. This work proposes a generic method to stochastically distort an original count variable to obtain a new count variable with relatively less variability than in the original variable. The proposed mechanism, termed condensation, attracts probability masses from the quantiles in the tails of the original distribution and redirect them toward quantiles around the expected value. If the original distribution can be simulated, then the simulation of variates from a condensed distribution is straightforward. Moreover, condensed distributions have a simple mean-parametrization, a characteristic useful in a count regression context. An application to the negative binomial distribution resulted in a distribution allowing under, equi and overdispersion. In addition to graphical insights, fields of applications of special cases of condensed Poisson and condensed negative binomial distributions were pointed out as an indication of the potential of condensation for a flexible analysis of count data

The broad global distribution of freshwater clams belonging to the genus Corbicula is driven by multiple hermaphroditic lineages. These lineages, characterized by shared morphological traits and phenotypic plasticity, pose challenges to morphological identification. Genetic markers, such as the mitochondrial COI gene, play a crucial role in delineating these lineages and their ranges. Morphotypes represent observed phenotypic variations, while lineages are defined based on genetic markers. Here, we comprehensively review Corbicula's distribution in Argentina, dis-criminate extant lineages based on both morphological and genetic (COI) data, and describe variation in internal and external morphology using 15 Argentine populations. Haplotype net-works identified two mitochondrial lineages: A/R morphotype (FW5 haplotype) and C/S mor-photype (FW17 haplotype). Strikingly, despite having similar vectors, origins, and invasive stages, Corbicula lineages exhibit virtually segregated distributions. However, intermediate morphotypes and both mitochondrial haplotypes are found in sympatry in northeastern Argen-tina, suggesting the presence of hybrids due to maternal genome retention. These findings con-tribute to the clarification of the identity and distribution of Corbicula lineages in Argentina, where the genus has been found for over half a century. Similar studies are needed in other areas to better understand the invasion patterns of a successful and plastic group.

Inflammation is the response of the immune system to infection and injury, with complex interactions with the body, tissues and cells, and plays an important role in the initiation and progression of many diseases such as cancer and cardiovascular disease. Traditional excipients functioning as drug delivery systems can reduce the side effects of systemic distribution of inflammatory drugs. Oil phase, a common excipient in nanoemulsions (NEs), has the advantages of assisting the formation of emulsions, loading lipophilic drugs, thermodynamic stability, wide sources, low price and easy availability. In particular, some of them, like linolenic acid and medium chain triglyceride (MCT), also function as inhibitors of systemic inflammation marker and vascular inflammation marker. However, the influences of different oil phases on the construction of NEs and their distribution in vivo have not been fully investigated. Herein, Tween 80 and ethyl alcohol were screened out as emulsifiers and co-emulsifiers, and three different oil phases used in clinical practice widely, including MCT, oleic acid (OA), and ethyl oleate (EO), were selected as the oil phase to prepare NEs delivery platform. Three NEs had consistent size, potential, morphology, excellent stability and mitochondrial localization function. Importantly, they exhibited superior cellular uptake capacity in inflammatory-injuried human umbilical vein endothelial cells and significantly targeted the brain, lung, heart and thoracic aorta in the lipopolysaccharide-induced mouse and zebrafish larvae inflammation models. Meanwhile, the fluorescence intensities of three NEs were different in these organs, suggesting that their differential enrichment might provide alternative delivery platform for disease treatment in the corresponding organs.

This paper deals with experimental study of the influence of conductive (Fe₃O₄) and insulating (Al₂O₃) nanostructured particles at various concentrations on the dielectric strength of transformer mineral oil. The method of preparation and characterization of these nanofluids (NFs) through the measurements of zeta potential, the real and imaginary parts of dielectric constant as well as the concentration and size of nanoparticles using Scanning Electron Microscope (SEM) images of nanoparticles powders and Dispersive x-ray Spectroscopy (EDS) analysis are presented. Experimental findings reveal that these two types of nanoparticles materials significantly improve AC breakdown voltage and the magnitude of this improvement depends on the concentration, size and nature (material) of nanoparticles. For a given type of nanoparticles, the effect is more marked with the smallest nanoparticles. The conductive nanoparticles offer higher enhancement of dielectric strength compared with insulating nanoparticles based nanofluids. With Fe₃O₄, the breakdown voltage (BDV) can exceed twice that of mineral oil and it increases by more than 76% with Al₂O₃. The physicochemical mechanisms implicated in this improvement are discussed.

The rodents of Saudi Arabia consist of 20 species and 12 genera within four families (Gliridae, Dipodidae, Muridae, and Hystricidae). Details on the past and present distribution of the rodents were included along with available data on their habitat preference and biology. The eastern central part of Saudi Arabia covering Tuwiq mountains plateau, including the vicinity of Riyadh, hosts the highest number of rodent species. Analysis of the rodent fauna of Saudi Arabia revealed that they have four major zoogeographical affinities; Palaearctic-Oriental (one species), Afrotropical- Palaearctic (six species), Palaearctic (four species), endemic to Saudi Arabia and Yemen (three species), Afrotropical-Palaearctic-Oriental (three species) and three cosmopolitan species. According to the National Red List, the Euphrates Jerboa, S. euphratica, is listed as Endangered, Near Threatened for the Indian Crested Porcupine, H. indica, three species as Data Deficient, while the rest are considered as Least Concern.

Monitoring is an important component of pest management, to prevent or mitigate outbreaks of native pests, and to check for quarantine organisms. Surveys often rely on trapping, especially when the target species respond to semiochemicals. Many traps are available for this purpose, but they are bulky in most cases, which raises transportation and deployment issues, and they are expensive, which limits the size and accuracy of any network. To overpass these difficulties, entomologists have used recycled material, such as modified plastic bottles, producing cheap and reliable traps but at the cost of recurrent handywork, not necessarily possible for all end-users (e.g., for national plant protection organizations). These bottle-traps have allowed very large surveys which would have been impossible with standard commercial traps, and we illustrate this approach with a few examples. Here we present, under a Creative Commons BY-SA License, the blueprint of a fan-trap, a foldable model, laser-cut from a sheet of polypropylene, that can rapidly be produced in large numbers, and could be transported and deployed in the field with very little efforts. Our first field comparisons show that fan-traps are as efficient as bottle-traps, and we describe two cases where they are being used for monitoring.

Bemisia tabaci (Gennadius) is a polyphagous, highly destructive pest capable of vectoring viruses in most agricultural crops. Currently, information on the distribution and genetic diversity of B. tabaci in South Sudan is not available. The objectives of this study were to investigate the genetic variability of B. tabaci infesting sweet potato and cassava in South Sudan. Field surveys were conducted between August 2017 and July and August 2018 in 10 locations in Juba County, Central Equatoria State, South Sudan. Sequences of mitochondrial DNA cytochrome oxidase I (mtCOI) were used to determine the phylogenetic relationships between sampled B. tabaci. Six distinct genetic groups of B. tabaci were identified including three non-cassava haplotypes (Mediterranean (MED), Indian Ocean (IO) and Uganda) and three cassava haplotypes (Sub-Saharan Africa 1 sub-group 1 (SSA1-SG1), SSA1-SG3 and SSA2). MED predominated on sweet potato and SSA2 on cassava in all the sampled locations. The Uganda haplotype was also widespread, occurring in five of the sampled locations. This study provides important information on the diversity of B. tabaci species in South Sudan. A comprehensive assessment of the genetic diversity, geographical distribution, population dynamics and host range of B. tabaci species in South Sudan is vital for its effective management.

Cotton cultivation and sustaining its productivity is challenging in temperate arid regions around the globe. Exploring suitable cotton cultivation areas to improve productivity in such climatic regions is essential. Thus, this study explores the ecologically suitable areas of cotton cultivation using the Maxent model, having 375 distribution points of long-staple cotton and various factors, including 19 climatic factors, 2 terrain factors, and 6 soil factors in Xinjiang. The area under the curve (AUC) of the predicted results was greater than 0.9, indicating that the model's predictions had fairly high accuracy. However, the main environmental factors that affect cotton's growth are the lowest temperature in the coldest month, the hottest month, the precipitation in the driest season, and the monthly average temperature difference. Further, the temperature factors contribute 71%, while the contribution ratio of terrain and soil factors is only 22%. The research shows that the current planting area is consistent with the predicted area in many areas of the study. Still, some areas, such as the Turpan region, northwest of Bayingolin Mongol Autonomous Prefecture, are supposed to be suitable for planting cotton, but it is not planted. The current potential distribution area of long-staple cotton is mainly located in Aksu Prefecture and the northern part of the Kashgar Prefecture region. The climatic prediction shows that the growing area of long-staple cotton may expand to southern Altay, central Aksu, and Bortala Mongol Autonomous Prefecture. This study will be helpful for cotton cultivation suitability areas in Xinjiang and other regions with similar environments.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

The author attempts to reconstruct the climatic vicissitudes of the Mediterranean to explain why only broadly distributed Eurasian forest species have penetrated the Mediterranean peninsulas. He has carried out a bibliographic survey of the status of breeding forest birds in Italy over 15 decades (1872-2022) in order to establish an objective long-term trend (stable, increasing, decreasing, etc.). The number of breeding forest birds in Italy amounts to 61; their distribution, with a few exceptions, indicates that they are widespread in Eurasia, but only a small percentage of Eurasian forest species have colonized Italy and the other Mediterranean peninsulas, namely 49 in Iberian, 61 in Italian and 64 in Balkan peninsulas; a small percentage of them (between 10.9 and 14.3%) belongs to trans-Saharan migrants. The similarity between the forest species on the three peninsulas (Iberian, Italian and Balkan) results between 0.45 and 0.48, indicating a certain differ-ence in the overall fauna on the three territories. Not all species have penetrated southwards into the three peninsulas; for example, some that stopped in the Italian Alps have instead arrived to the forests of Greece, at a latitude corresponding to southern Italy, or species that in Italy stopped in the northern Apennines in the other two peninsulas have instead arrived far south. Iberian peninsula and the island of Corsica hold three endemic species among breeding forest birds, Italian and Balkan peninsulas have not endemic species. Overall, the Mediterranean presently hosts mainly neo-endemic taxa among forest bird species; the only paleo-endemics can be considered the three species of nuthatches living in Corsica, Algeria, and Turkey (other than Caucasus and the islet of Lesvos) and Le Vaillant’s woodpecker in the Maghreb (North Africa). Italian forests cover ca. 40% of land surface and since 1980’ are increasing, but 22% of them do not have a natural origin. However, it is difficult to know the true increase of forests, because some of them are fired every year. The presence of some ecologically demanding forest birds depends on the age of the trees, permanent open spaces and other characteristics at the edge of woodland.

The Amazon region has the most incredible diversity of freshwater stingrays; however, there are still places where information about this group is scarce. The present work aims to record the occurrence of freshwater stingrays in the Uatumã river basin, Amazonas, Brazil. For this, collections were carried out in three municipalities bathed by the Uatumã River, Presidente Figueiredo, Itapiranga and São Sebastião do Uatumã. The rays were collected through fishing using a hand net and, after capture, were identified through the pattern of the dorsal and ventral color of the disc, the absence or presence of the labial groove and the organization of the row of spines on the tail, too were also measured, weighed and sexed. In total, 69 specimens of Potamotrygonines were captured, 59 of which were from the genus Potamotrygon and ten individuals from the genus Paratrygon. The present study provides preliminary information on the characteristics of freshwater stingray species that may occur in the Uatumã River. Furthermore, new research is necessary to improve the identification of specimens to determine the diversity and elucidate aspects related to the biology of elasmobranchs in the Uatumã River Basin, Brazil.

In this work, we explore the extreme searching of multidimensional functions by natural gradient descent based on Dirichlet and generalized Dirichlet distributions. The natural gradient is based on describing multidimensional surface with probability distributions, which allows us to reduce changing the accuracy of gradient and step-size. In this article, we propose an algorithm of natural gradient descent based on Dirichlet and generalized Dirichlet distributions. We demonstrate that the natural gradient descent with step-size adaptation with Dirichlet and generalized Dirichlet distributions has higher accuracy and does not take a large number of iterations for minimizing test functions than gradient descent and Adam.

A critical analysis of the classical definition of outsiders is given. Some examples show that this notion is not universal and has at least two drawbacks. Particularly, the set of outsiders may have the probability arbitrary close to one half. On the other hand, the deleting of the set of outsiders may dramatically change the value of the median.

Tourism is increasingly becoming one of the most important components of the economy. Coastal tourism is of particular importance in our country, this is because Albania has a very favorable geographical position. The tourist destination chosen for study in this paper is Durrës. It is analyzed as a complex dynamic system that evolves with a series of techniques and methods drawn from the area of network theory. The main objective of this paper is the comparison of technological and socio-economic networks, through different methods and techniques. The methodology of this research includes different data collection methods for both networks and their analysis. 504 nodes were taken into consideration. A significant part of the research is based on network theory, using algorithms and network analysis techniques to reveal their static and dynamic characteristics. Through this paper we show that the internet network and the socio-economic network of Durrës are similar in some aspects and have a great impact on the development of the tourist destination. The analysis of these two networks provides a deeper picture of the relations between the actors of the destination and helps to improve the tourism strategies and the economic development of the area. Thus, the research is an attempt to better understand the impact of technological and socio-economic networks in the development of the tourist destination of Durrës and uses different ways of network analysis to discover the similarities and differences between them.

Taxes on the consumption of certain products have played a key role in public revenue analysis in European countries. This work aims to assess the differences in tax planning on new non-combustion products across some European territories. Through theoretical analysis, the paper has three distinct aspects. Firstly, we show the taxpayer profile in different countries. Secondly, the study analyzes the risks for the health system and the individual. Thirdly, the design of the land tax is based on previous experience and planning in Europe. This paper concludes with a case study for different countries: 1) Spain “vapers” and “smokers”, where the analysis is based on micro-data from the European Health Interview Survey 2020. 2) Sweden with the analysis of snus, shows it as a practice to reach economic savings while decreasing economic costs thanks to the nudging of consumers towards better products. The results show taxation and, specially, land taxation, should consider differences in planning in the case of new products, such as the non-combustion products, given the user per capita income and the potential lower health risks involved.

A descriptive epidemiological study has been conducted using hospital database of Teaching Veterinary Hospital (TVH) at Jhenaidah Government Veterinary College (JGVC) from July 2018 to June 2019. The study aimed to estimate the proportionate prevalence of different livestock and poultry diseases along with their spatiotemporal distribution and drug prescribing pattern. A total of 960 clinical cases were recorded during the study period. Ectoparasitic cases were proportionately higher in cattle (25.2%), whereas Peste des Petits Ruminants (PPR) cases were more frequent in goat (53.4%). The proportionate prevalence of other cases in cattle was Fascioliasis (14.3%), Myiasis (11.2%) and Foot and Mouth Disease (FMD) (7.2%). The proportionate prevalence of other cases in goats were vitamin and mineral deficiency (12.3%), bloat (5.2%), abscess (4.7%), and dog bite (1.2%). Again, the proportionate prevalence of poultry diseases was Infectious Bursal Disease (41.2%), salmonellosis (33.4%), fowl cholera (13.7%) and pox (7.8%). Most of the cattle cases were highly prevalent during the summer season except fascioliasis. In goat, PPR was predominated in the rainy season whereas myiasis was in the winter. Around 92% of disease cases were spatially located within the 2.5 km radius of the TVH of JGVC where only 0.9% of disease cases came from >10km away from TVH of JGVC. Simple linear regression identified a significant relation (p=0.01) with the distance and number of diseased animals came to the hospital. Antimicrobials belonging to b-Lactam group were most frequently prescribed for both poultry (48.6%), cattle (32.5%) followed by goat (9.2%), however sulfar drugs (34.8%) were commonly prescribed for goat cases. This type of study is very novel in Jhenaidah region of Bangladesh that might contribute to the researchers for further investigation.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.