This research presents a comprehensive computational analysis of the two-phase flow dynamics within a three-dimensional porous transport layer (PTL) in a proton exchange membrane (PEM) electrolyzer. Employing advanced computational fluid dynamics (CFD) and a volume of fluid (VOF) approach, the study utilizes the finite-volume method to model a time-dependent, isothermal process within a laminar flow regime. Notably, the study treats oxygen as the dispersed phase and water as the continuous phase within the system. Investigations on the anode side uncovered the formation of gas bubbles on the electrode's surface subsequent to the electrochemical reaction. The simulation, spanning 5 seconds with 0.25-second intervals, highlights the critical role of the time interval between the initiation and 2 seconds in achieving pressure and velocity equilibrium within the PTL. The initial 0.75 seconds witnessed a peak in oxygen concentration, followed by its movement across the PTL, exhibiting a transition from regions of lower to higher concentration, consistent with known physical behaviour. Remarkably, the model recorded the highest pressure of 3.5 Pa at 0.25 s. Furthermore, the study observed an incremental pressure drop from 0.25 s to 0.5 s and 1 s, approximately amounting to 28.5% and 20%, respectively, ultimately leading to a uniform pressure distribution within the model. Over time, the pressure drop intensified across the entire model due to the evolving nature of the oxygen gas. These findings provide valuable insights into the complex dynamics of two-phase flow processes within PEM electrolyzers, contributing to the advancement of sustainable energy technologies.

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in MV-class bushing aimed to detect partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signals. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) principle for voltage measurement and D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kV) were less than 0.2% and 10 minutes, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

We discuss two queueing-inventory systems with catastrophes in the warehouse. Catastrophes occur according to Poisson process and upon arrival of a catastrophe all inventory in the system is instantly destroyed. But consumer customers in the system (in the server or in the buffer) continue still waiting for the replenishment of the stock. The arrivals of the consumer customers follow a Markovian Arrival Process (MAP) and they can be queued in an infinite buffer. Service time of a consumer customer follows a phase-type distribution. The system receives negative customers whose have Poisson flows to service facility and upon arrival of a negative customer one consumer customer is pushed out from the system, if any. One of two replenishment policies can be used in the system: either (s,S) or (s,Q). If upon arrival of the consumer customer, the inventory level is zero, then according to the Bernoulli scheme, this customer is either lost (lost sale scheme) or join the queue (backorder sale scheme). The system is formulated by a four-dimensional continuous-time Markov chain. Steady state distribution is obtained using the matrix-geometric method. A comprehensive numerical study is performed on the performance measures under various replenishment policies. Finally, an optimization study is presented.

At the molecular level, aging is often accompanied by dysfunction of stress-induced membrane-less organelles (MLOs) and changes in their material state. In this work, we analyzed the proteins included in the proteome of stress granules (SGs) and P-bodies for their tendency to transform the material state of these MLOs. Particular attention was paid to proteins whose gene expression changes during replicative aging. It was shown that the proteome of the studied MLOs practically does not differ in the analyzed characteristics and consists of completely or partially intrinsically disordered proteins, 30 - 40% of which are potentially capable of liquid-liquid phase separation (LLPS). At the same time, the proportion of proteins capable of spontaneous LLPS is relatively small, which indicates the leading role of nucleic acids in the biogenesis of these membrane-less organelles. Proteins whose gene expression changes during the transition of human cells to a senescent state make up about 20% of the studied proteomes. There is a statistically significant increase in the number of positively charged proteins in both datasets studied compared to the complete proteomes of these organelles. An increase in the relative content of DNA-, but not RNA-binding proteins, was also found in the stress-granules dataset with senescence-related processes. Among SG proteins potentially involved in senescent processes, there is an increase in the abundance of potentially amyloidogenic proteins compared to the whole proteome. The hnRPDL protein has the highest degree of disorder and highest propensity for LLPS among such proteins, which allows us to consider it as “potentially dangerous.” Proteins common to SGs and P bodies, potentially involved in processes associated with senescence, form clusters of interacting proteins. The largest cluster is represented by RNA-binding proteins involved in RNA processing and translation regulation. These data indicate that SG proteins, but not proteins of P-bodies, are more likely to transform the material state of MLOs. Furthermore, these MLOs can participate in processes associated with aging in a coordinated manner.

Tight junctions (TJ) are cell-cell adhesive structures that define the permeability of barrier-forming epithelia and endothelia. In contrast to this seemingly static function, TJs display a surprisingly high molecular complexity and an unexpected dynamic regulation, which allows the TJs to maintain a barrier in the presence of physiological forces and in response to perturbations. Cell-cell adhesion receptors play key roles during the dynamic regulation of TJs. They connect individual cells within cellular sheets and link sites of cell-cell contacts to the underlying actin cytoskeleton. Recent findings support roles of adhesion receptors in transmitting mechanical forces and promoting phase separation. In this review, we discuss newly discovered functions of cell adhesion receptors localized at the TJs and their role in the regulation of the barrier function.

Background: Malnutrition was associated with worse survival outcomes, impaired quality of life, and deteriorated performance status across various cancer types. We aimed to identify risk factors for malnutrition in patients with epithelial ovarian(EOC) and impact on survival. Methods: In our prospective study, we included the patients with primary and recurrent EOC, tubal or peritoneal cancer conducted. We assessed serum laboratory parameters, body mass index, nutritional risk index, nutritional risk screening score(NRS-2002), and bio-electrical impedance analysis. Results: We recruited a total of 152. Patients >65 years-old, with ascites of >500 ml, or with platinum-resistant EOC showed statistically significant increased risk of malnutrition when evaluated by NRS-2002(p-values = 0.014, 0.001, and 0.007, respectively). An NRS-2002<3 was an independent predictive factor for complete tumor resectability (p=0.009). The patients with NRS-2002≥3 had a median overall survival(OS) of seven months (95% CI=0-24 months), as compared to the patients with NRS-2002<3 where median OS was 46 months(p=0,001). Phase angle(PhAα)≤ 4.5 was the strongest predictor of OS. Conclusion: Malnutrition is an independent predictor of incomplete cytoreduction in study population. It is an independent prognostic factor for poor OS. Preoperative nutritional assessment is an effective tool in identification of high-risk groups within EOC characterized by poor clinical outcome.

Magnetic Resonance Imaging (MRI) is widely used in clinics and research due to its accurate disease identification and non-invasive nature. MRI is based on Nuclear Magnetic Resonance (NMR), which is also extensively employed in various fields. NMR and its modern versions involve intricate pre-processing steps before data analysis. These steps are initially processed in the time domain and subsequently in the frequency domain. While our previous review focused on time domain pre-processing (https://www.preprints.org/manuscript/202310.2032/v1), this review delves into the mathematical and statistical aspects of frequency domain pre-processing. We discuss essential pre-processing steps like phase error correction, baseline correction, solvent filtering, calibration and alignment, reference deconvolution, binning/bucketing and peak picking, peak fitting/deconvolution and compound identification, integration and quantification, normalization and transformation. Furthermore, we offer practical recommendations for each step.

Post-stroke depressive disorders (PSD) and post-stroke cognitive impairments (PCI) are frequent consequences of ischemic stroke (IS). The study was focused on exploring possible associations between relative volumes of cortical and limbic brain structures during the acute period of IS, and changes in biochemical indices of hypothalamic-pituitary-adrenal, sympathoadrenal medullary and inflammatory systems, with the development of PSD or PCI after mild or moderate IS. Patients developing PSD later on had significantly smaller relative volumes of the hippocampus, entorhinal cortex, and temporal pole versus patients without depressive symptoms. PCI development was associated with significantly smaller volumes of temporal pole and supramarginal gyrus versus patients without cognitive changes. Multiple logistic regression analysis showed higher likelihood of developing PSD in patients with smaller temporal pole volume (β0=10.9; β=-4.27; p=0.04) and increased salivary α-amylase activity (β0=-3.55; β=2.68e-05; p=0.02,). PCI likelihood was higher in patients with smaller supramarginal gyrus volume (β0=3.41; β=-0.99; p=0.047), smaller temporal pole volume (β0=3.41; β=-3.12; p=0. 06), and increased hair cortisol concentration at admission (index of accumulated stress load within a month before IS; β0=3.41; β=-0.05; p=0.08). The data support the hypothesis suggesting predisposition to PSD and PCI and multi hit scenarios of their pathogenesis with IS providing a final hit.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

The spin-1/2 quantum transverse Ising model, defined on a ladder structure, with nearest-neighbor and four-spin interaction on a plaquette, is studied by using exact diagonalization and finite-size-scaling procedures. The quantum phase transition between the ferromagnetic and paramagnetic phases has been obtained in the thermodynamic limit. The critical transverse field decreases as the antiferromagnetic four-spin interaction increases, and reaches a multicritical point. However, the exact diagonalization approach was not able to capture the essence of the dimer phase beyond the multicritical transition.

An array of diverse processes and factors have been linked to the pathoetiology and pathophysiology of Parkinson’s disease (PD), including systemic CNS factors. This article reviews some of the many processes and factors linked to the emergence and progression of PD that culminates in the loss of substantia nigra pars compacts (SNpc) in PD patients. It is proposed that SNpc astrocytes may be a key hub, with numerous systemic and CNS factors acting to suppress the astrocyte tryptophan-melatonin pathway, leading to a loss of astrocyte melatonin and lactate for SNpc dopamine neurons. Consequently, dopamine neurons show an increase in α-synuclein, oxidative stress and suboptimal mitochondrial function, partly due to the loss of melatonin induced PTEN-associated kinase (PINK)1/parkin and mitophagy. This leads to an increase in the major histocompatibility (MHC)-1 and the chemoattraction of CD8+ T cells that destroy SNpc dopamine neurons in an ‘autoimmune’/’immune-mediated’ manner. The upstream processes driving the end-point ‘chaos’ of SNpc dopamine neuron loss are proposed to be driven by the suppression of night-time pineal melatonin, gut microbiome derived butyrate and possibly bcl2-associated athanogene (BAG)-1, which all act to suppress the glucocorticoid receptor (GR) translocation to the nucleus in all systemic and CNS cells, thereby potentiating the effects of the rising levels of cortisol over the night and accelerated rise in the course of the cortisol awakening response (CAR). The potentiation of cortisol effects at the GR has consequences for the homeostatic regulation of the diverse array of systemic and CNS microenvironments, as well as a distinct regulation of different immune and glia cells. The morning CAR is classically proposed to ‘prepare the body for the coming day’. However, the differential regulation of the GR over the circadian rhythm at night would indicate that such preparation for the coming day may be powerfully determined by night-time factors and processes. The article integrates this systemic, night-time pathoetiology with the ‘immune-mediated’ processes that ultimately drive SNpc dopamine neuron loss. This has a number of novel future research and treatment implications.

In this paper, intrusion detection systems are thoroughly investigated utilizing the CSE-CIC-IDS-2018 dataset. The research is divided into three key phases: first, applying Data Cleaning, Exploratory Data Analysis, and Data Normalization techniques (min-max and z-score) for preparing data across distinct classifiers. Second, feature importance is reduced using a combination of Principal Component Analysis (PCA) and Random Forest (RF), with the goal of improving processing speed and decreasing model complexity. This stage comprises a comparison with the entire dataset. Finally, machine learning algorithms (XGBoost, CART, DT, KNN, MLP, RF, LR, and Bayes) are applied to specific features and preprocessing approaches. Surprisingly, the XGBoost, DT, and RF models outperform in both ROC values and CPU runtime. Following evaluation, which includes PCA and RF feature selection, an optimal set is produced.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

Alzheimer’s disease manifests itself as a complex pathological condition with neuroinflammation, oxidative stress and cholinergic dysfunction being a few of the many pathological changes. Due to the complexity of the disease current therapeutic strategies aim at a multitargeted approach often relying on a combination of sub-stances with versatile and complementary effects. In the present study, unique combination of α-lipoic acid, citicoline, extracts of leaves from olive tree and green tea, Vitamin D3, selenium and an immune supporting complex was tested in a scopolamine-induced dementia in rats. Using behavioral and biochemical methods we assessed the effects of this combination on learning and memory, and elucidated the mechanisms under-lying its effects. Our results showed that as compared to the components, experimental combination was most efficient in improving short- and long-term memory assessed by the step-through method as well as spatial memory, assessed by T-maze and Barnes maze underlying decrease in AChE activity and LPO, in-creases in SOD activity in cortex; activities of catalase and GPx, levels of BDNF and pCREB in the hippocam-pus. No significant histopathological changes or blood parameter changes were detected, making the experi-mental combination an effective and safe candidate in a multitargeted treatment of AD.

For decades SrTiO3 is in the focus of research with seemingly never-ending new insights regarding its ground state properties, its application potentials, its surface and interface properties, the superconducting state, the twin boundaries and domain functionalities, etc. Here, we focus on the already well-investigated lattice dynamics of STO and show that four different temperature regimes can be identified which dominate the elastic properties, the thermal conductivity and the birefringence. These regimes are the low-temperature quantum fluctuation dominated one, followed by an intermediate regime, the region of the structural phase transition at ~105 K and its vicinity, and at high temperatures a regime characterized by precursor and saturation effects. They can all be elucidated by lattice dynamical aspects. The relevant temperature dependences of the soft modes are discussed and their relationship to lattice polarizability is emphasized.

We show that, as in the case of the principle of minimum action in classical and quantum mechanics, there exists an even more general principle in the very fundamental structure of quantum space-time: This is the principle of minimal group that allows to consistently and simultaneously obtain a natural description of the spacetime dynamics and the physical states admissible in it. The theoretical construction is based on the physical states that are average values of the generators of the Metaplectic group Mp(n) , the double covering of SL(2C) in a vector representation, with respect to the coherent states carrying the spin weight. Our main results here are: (i) There exists a connection between the dynamics given by the Metaplectic group symmetry generators and the physical states (mappings of the generators through bilinear combinations of the basic states). (ii) The ground states are coherent states of the Perelomov-Klauder type defined by the action of the Metaplectic group which divide the Hilbert space into even and odd states mutually orthogonal. They carry a spin weight 1/4 and 3/4 respectively from which, two other basic states can be formed. (iii) The physical states, mapped bilinearly with the basic 1/4 and 3/4 spin weight states, plus their symmetric and antisymmetric combinations, have spin contents s = 0, 1/2, 1, 3/2 and 2. (iv) The generators realized with the bosonic variables of the harmonic oscillator introduce a natural supersymmetry and a superspace whose line element is the geometrical Lagrangian of our model. (v) From the line element as operator level, a coherent physical state of spin 2 can be obtained and naturally related to the metric tensor. (vi) The metric tensor is naturally discretized by taking the discrete series given by the basic states (coherent states) in the n number representation, reaching the classical (continuous) space-time for n going to infinity. (vii) There emerges a relation between the eigenvalue of our coherent state metric solution and the black hole area (entropy) as A_{bh}/4 l_{p}^{2} = I alpha I relating the phase space of the metric found g_{ab} and the black hole area A_{bh} through the Planck length l_{p}^{2} and the eigenvalue I alpha I of the coherent states. As a consequence of the lowest level of the quantum discrete space-time spectrum, eg the ground state associated to n = 0 and its characteristic length, there exists a minimum entropy related to the black hole history.

The commonly quoted bistable Higgs potential is not a proper description of the Higgs field because, among other technical reasons, one of its stable states acquires a negative expectation value in vacuum. We rely on formal catastrophe theory to derive the form of the Higgs potential that admits only one positive mean value in vacuum. No symmetry is broken during the ensuing phase transition that assigns mass to the Higgs field; only gauge redundancy is “broken” by the appearance of phase in the massive state, but this redundancy is not a true symmetry of the massless field. Furthermore, a secondary, certainly amusing conclusion is that, in its high-energy state, the field oscillates about its potential minimum between positive and negative masses; but it is doubtful that such evanescent states can survive below the critical temperature of 159.5 GeV, where the known particles were actually created.

Mass transfer and phase transition have important effect on the velocity of bubble migration in deepwater wellbore, and accurate prediction of bubble migration velocity is crucial for calculating the safe shut-in period of deepwater oil and gas well. Therefore, the effect of bubble dissolution mass transfer and hydrate phase transition on bubble migration behavior in deepwater environment have attracted extensive attention from researchers in the fields of energy, marine chemistry, and marine engineering safety. In this work, a new model of bubble migration velocity in deepwater is developed, which considers the effect of hydrate phase transition and gas-water bidirectional cross-shell mass transfer during bubble migration. Based on the observation data of bubble migration in deepwater, the reliability of the model in predicting bubble migration velocity is verified. Then, the model is used to calculate and analyze the bubble migration velocity and bubble migration cycle under different initial bubble size, different annular fluid viscosity and density. The results show that the initial size of bubble and the viscosity of annulus fluid are the main factors affecting the migration velocity of bubble, but the density of annulus fluid has little effect on the migration velocity of hydrated bubble and clean bubble. In addition, the migration velocity of clean bubble gradually increases during the migration process from the bottom to the wellhead, while the migration velocity of hydrated bubble is divided into gradually decreasing stage and slowly increasing stage. The gas consumption and the thickening of hydrate shell in the gradually decreasing stage play a dominant role, and the increase of bubble volume caused by the decrease of pressure in the slowly increasing stage is the most important factor. The formation of hydrated bubble can significantly reduce the migration velocity of bubble and effectively prolong the safe shut-in period. This study provides a reference for quantitative description and characterization of complex bubble migration behavior with phase change and mass transfer in deepwater environment.

This study employs the phase-field regularized cohesion model (PF-CZM) to simulate crack propagation and damage behavior in porous granite. We investigate how pore radius (r), initial crack-pore distance (D), and pore-crack angle (θ) impact crack propagation. The simulation findings reveal that, with a fixed deflection angle and initial crack-pore distance, larger pores are more likely to induce crack extension under identical loading conditions. Moreover, with r and θ keeping constant, the crack extension can be divided into two stages: from its initiation to the lower edge of the pore and then from the lower edge to the upper boundary of the model. By varying the values of D and r, we derive multiple combinations of different D/r ratios and pore radii. These results demonstrate that with constant r, cracks tend to deflect toward the pore closer to the initial crack. Conversely, when D is maintained constant, cracks will preferentially deflect toward pores with a larger r. In summary, the numerical simulation of rock pores and initial cracks, based on the PF-CZM, exhibits remarkable predictive capabilities and holds significant potential in advancing rock fracture analysis.

The work carried out first-principles calculations within the framework of density functional theory to study the structural stability of the CsSnI₃ compound and the influence of phase transitions on their electronic and optical properties. Using the GGA and SCAN functionals, the relaxed structures of the CsSnI₃ phases were obtained and their geometric characteristics were assessed. Using the Phonopy code based on VASP, calculations of phonon and thermodynamic properties were performed, and the temperatures of phase transitions of CsSnI₃ were determined. The temperature dependences of the thermodynamic parameters α-, β-, γ- and δ-phases of CsSnI₃ were analyzed. The trends in free energy, entropy, enthalpy, heat of formation energy and heat capacity were justified in terms of the pattern of changes in the total energy of the four phases of CsSnI₃ from VASP calculations. It is shown that at 0 K the non-perovskite structure of the CsSnI₃ compound (δ-CsSnI₃) is the most stable (followed by γ-CsSnI₃), and the tetragonal phase (β) is quite unstable, having the highest energy among the perovskite phases. It was revealed that at temperatures above 450 K the tetragonal phase becomes stable, and when the temperature drops, it transforms into the cubic phase (α-CsSnI₃). The phase transition between the β and γ phase of perovskite occurs in the range of 300-320 K, and at 320 K a black-yellow transformation of CsSnI₃ occurs in which the cubic phase (black perovskite) undergoes a phase transition to a non-perovskite conformation (yellow phase). The presence of temperature phase transitions between two orthorhombic phases of CsSnI₃ at 360 K was discovered, although direct transitions of the α⟷γ and γ⟷δ types have not yet been reported in any experiment, except for γ→δ transitions under the influence of moisture. Based on well-relaxed structures (from the SCAN calculations), the band gap widths for four CsSnI₃ phases were calculated and compared with experimental measurements. Electronic properties and Fermi level shifts as a result of phase transformations of CsSnI₃ were assessed using the HSE06 functional and machine learning prediction. The values of the complex dielectric constant and the refractive index of all phases of the CsSnI₃ were determined.

A new mesogenic non-symmetric dimeric monomer with a terminal olefin function, forming a twist bend nematic (Ntb) as well as a nematic (N) phase was synthesized, using an enhanced synthetic methodology, which avoids isomerization of the terminal double bond in the preparation of the dimer. This monomer was attached to a pentamethyldisiloxane group, resulting in SmA LC phase behaviour of the ensuing material. Linking the monomer to a siloxane main chain resulted in nematic phase behaviour. Detailed studies with the Ntb phase forming dimer DTC5C7 show full miscibility of the dimer and the new LC polymer in the LC state, suggesting that the side-chain LC polymer forms a Ntb phase as the low temperature nematic phase. Copolymerizing the monomer with a cyanobiphenyl based monomer allows to tune the glass transition and phase behavior further.

Super-resolution technology is important not only in bio-related fields but also in nanotechnology, particularly in the semiconductor industry, where fine patterning is required and super-resolution is essential. However, observing microstructures beyond the diffraction limit proposed by Abbe and Rayleigh is considered impossible because of diffraction in traditional optical microscopy ob-servation techniques. However, in recent years, it has been possible to observe microstructures beyond the Rayleigh criterion by analysing the phase distribution of light. This study investigated the physical reasons why phase analysis makes this new analysis technique possible using simula-tions. The results confirmed that the phase component of the zero-order diffracted light reflected from the microstructure and able to pass through the lens system contained the phase information related to the shape of the measured object. Analysis of this information demonstrates the possi-bility of realising super-resolution based on speckle interferometry.

Bimetallic colloidal CoPt nanoalloys, with a very low platinum content, were successfully synthesized following a modified polyol approach. Powder X-ray diffraction, IR spectroscopy, thermogravimetric analysis, and Transmission Electron Microscopy studies were performed to estimate the crystal structure, morphology and surface functionalization of the colloids respectively, while the room temperature magnetic properties were measured using Vibrating Sample Magnetometer. The particles exhibit excellent uniformity, with a narrow size distribution, and display strong room temperature hysteretic ferromagnetic behavior even in the as-made form. Upon annealing at elevated temperatures, progressive formation and co-existence of exchange coupled both chemically ordered and disordered phases, significantly enhance the room temperature coercivity.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

The α-synucleinopathies are a group of neurodegenerative diseases characterized by the deposition of α-synuclein aggregates (α-syn) in the brain. Currently, there is no suitable tracer to enable a definitive early diagnosis of these diseases. We reported candidates based on 4,4'-disarylbisthiazole (DABTA) scaffold with a high affinity towards α-syn and excellent selectivity over Aβ and tau fibrils. Based on prior in silico studies a focused library of 23 halide-containing and O-methylated DABTAs was prepared. The DABTAs were synthesized via a modified two-step Hantzsch thiazole synthesis, characterized, and used in competitive binding assays against [3H]PiB, and [3H]DCVJ. The DABTAs gave an overall chemical yield of 15 – 71%, with a calculated lipophilicity of 2.5 – 5.7. The ligands demonstrated an excellent affinity to α-syn with both [3H]PiB and [3H]DCVJ: Ki 0.1 – 4.9 nM and up to 20 – 3900-fold selectivity over Aβ and tau fibrils. It could be concluded that in-silico simulation is useful for the rational design of a new generation of DABTAs. Further investigation of the leads in the next step is encouraged: radiolabeling of the ligands with radioisotopes such as fluorine-18 or carbon-11 for in vivo, ex vivo and translational research and for further in vitro experiments on human-derived protein aggregates.

Our previous studies showed that in patients with brain diseases neurotrophic factors in lacrimal fluid (LF) may change more prominently than in blood serum (BS). Since glial cell line-derived neurotrophic factor (GDNF) is involved in control of neuronal networks in epileptic brain, we aimed to assess GDNF levels in LF and BS as well as BDNF, hypothalamic-pituitary-adrenocortical and inflammation indices in BS of patients with focal epilepsy (PWFE), epilepsy and comorbid depression (PWFE+MDD) compared with major depressive disorder (PWMDD) and healthy controls (HC). GDNF levels in BS were similar in patients and HC and higher in PWFE taking valproates. GDNF levels in LF were significantly lower in all patient groups compared to controls, and independent of drugs used. LF and BS GDNF concentrations positively correlated in HC, but not patient groups. BDNF level was lower in BS of patients compared with HC and higher in PWFE+MDD taking valproates. Logistic regression models demonstrated that GDNF decrease in LF may be an important predictor of focal epilepsy. Probability of focal epilepsy can be evaluated using GDNF in LF and BDNF in BS; MDD - GDNF in LF, cortisol and TNF-α in BS; epilepsy with MDD - GDNF in LF, TNF-α and BDNF in BS.

The formation and functioning of membrane-less organelles (MLOs) is one of the main driving forces in the molecular life of the cell. These processes are based on the separation of biopolymers into phases regulated by multiple specific and nonspecific inter- and intramolecular interactions. Among the realm of MLOs, a special place is taken by the promyelocytic leukemia nuclear bodies (PML-NBs or PML bodies), which are the intranuclear compartments involved in the regulation of cellular metabolism, transcription, maintenance of genome stability, response to viral infection, apoptosis, and tumor suppression. According to the accepted models, specific interactions, such as SUMO/SIM, formation of disulfide bonds, etc., play a decisive role in the biogenesis of PML bodies. In this work, a number of bioinformatics approaches were used to study proteins found in the proteome of PML-bodies for their tendency to spontaneous liquid-liquid phase separation (LLPS), which is usually caused by weak nonspecific interactions. 205 proteins found in PML bodies have been identified. It has been suggested that UBC9, P53, HIPK2, and SUMO1 can be considered as the scaffold proteins of PML bodies. It was shown that more than half of the proteins in the analyzed proteome are capable of spontaneous LLPS, with 85% of the analyzed proteins being intrinsically disordered proteins (IDPs), and remaining 15% being proteins with intrinsically disordered protein regions (IDPRs). About 44% of all proteins analyzed in this study contain SUMO binding sites and can potentially be SOMYylated. These data suggest that weak nonspecific interactions play a significantly larger role in the formation and biogenesis of PML bodies than previously expected.

We study different aspects of an exactly solvable master equation (ME). Its simplicity allows one direct access to the details of its workings, highlighting significant features and peculiarities. The existence of phase transitions is unveiled.

The α-glucosidase inhibitor is of interest to researchers due to its association with type-II diabetes treatment by suppressing postprandial hyperglycemia. Hesperidin is a major flavonoid in orange fruit with diverse biological properties. This paper evaluates the effects of hesperidin on α-glucosidase through inhibitory kinetics, fluorescence quenching, and molecular docking methods for the first time. The inhibition kinetic analysis showed that hesperidin reversibly inhibited the α-glucosidase activity with an IC50 value of 18.52 M and the inhibition was performed in an uncompetitive type. Fluorescence quenching studies indicated that the intrinsic fluorescence of α-glucosidase was quenched via a static quenching process and only one binding site was present between hesperidin and α-glucosidase. The interaction between them was spontaneous and mainly driven by hydrogen bonds as well as hydrophobic forces. Furthermore, molecular docking results suggested that hesperidin might bond to the entrance or outlet part of the active site of α-glucosidase through a network of five hydrogen bonds formed between hesperidin and the four amino acid residues (Trp709, Arg422, Asn424, and Arg467) of ?-glucosidase and hydrophobic effects. These results provide new insights into the inhibitory mechanisms of hesperidin on α-glucosidase, supporting the potential application of hesperidin-rich orange product as a hypoglycemic functional food.

Zinc, being a part of many proteins and enzymes, plays an important role in the vital processes of the body. Racemic α-lipoic acid (LA) has a wide range of biological activities: antioxidant, antidiabetic, anticancer, and it is also used in diseases such as Parkinson's and Alzheimer's. Nowadays, the synthesis and structural studies of new zinc complexes with biologically active compounds are of great importance for drug discovery. This work shows the studies carried out on the synthesis, structure, identification, also biological activity using in silico methods of a complex compound based on LA and zinc. A complex compound of zinc with LA (ZnLA) was synthesized in the presence of LA and zinc acetate in ethanol. The identification of ZnLA by (FT-IR, XRD and TGA-DTA), also DFT calculations at the B3LYP/def2-TZVPP level of theory was performed. The molecular docking investigation involved docking ZnLA with two different protein receptors such us Glycogen phosphorylase (2GPA) and Kv potassium channel beta subunit (1ZSX) using CB-Dock 2 server and Auto-Dock Vina program to determine the mechanism of action and biological activity. This study reveals potential ligand-protein interactions at the atomic level and suggests that the treatment of diabetes (non-insulin dependent) with ZnLA.

Ant Colony Optimization (ACO) is a stochastic optimization algorithm inspired by the foraging behavior of ants. We investigate a simplified computational model of ACO, wherein ants sequentially engage in binary decision-making tasks, leaving pheromone trails contingent upon their choices. The quantity of pheromone left is the number of correct answers. We scrutinize the impact of a salient parameter in the ACO algorithm, specifically, the exponent $\alpha$ that governs the pheromone levels in the stochastic choice function. In the absence of pheromone evaporation, the system is accurately modeled as a multivariate nonlinear P\'{o}lya urn, undergoing a phase transition as $\alpha$ varies. The probability of selecting the correct answer for each question asymptotically approaches the stable fixed point of the nonlinear P\'{o}lya urn. The system exhibits dual stable fixed points for $\alpha\ge \alpha_c$ and a singular stable fixed point for $\alpha<\alpha_c$. When pheromone evaporates over a time scale $\tau$, the phase transition does not occur and leads to a bimodal stationary distribution of probabilities for $\alpha\ge \alpha_c$ and a monomodal distribution for $\alpha<\alpha_c$.

This article presents the results of studies of the structure and conductive properties of Na3Fe2(PO4)3 polycrystals synthesized by solid-phase and melt (using concentrated optical radiation) methods. It has been established that with the melt method, the synthesis of the material occurs under significantly nonequilibrium temperature-gradient conditions, which leads to the creation of deformations in the sample that contribute to an increase in ionic conductivity. The ability of the Na3Fe2(PO4)3 structure to adapt to anomalous deformations that occur under temperature-gradient conditions indicates the elasticity of the crystalline framework {[Fe2(PO4)]3-}3∞. Through a comparative assessment of the structural parameters and conductive properties of these materials, it is shown that polycrystals obtained by the melt method have a better texture and greater ionic conductivity. The advantage of this method is that the duration of the synthesis of α-Na3Fe2(PO4)3 is halved. It is concluded that this method is applicable to obtain effective polycrystals of other compositions.

It's a method to achieve energy savings in single-phase active power greater than that obtained with the "Fan Law" in electric machines applied to ventilation. Quantitative analysis methods were based on electrotechnical techniques, practiced with the corresponding laboratory equipment on the working materials (three prototypes of electric machines). The results obtained from experimentation on the test bench were recorded in tables that collect data of formulas, values, and physical units. The discussion provides a comprehensive comparative study, mainly between power (watts), active energy consumption (kWh), and rotational speed (revolutions per minute). The permanent magnet synchronous motor (PMSM) with the coupling of an RL circuit design does mechanical work at its maximum speed of 3000 (RPM) with only 6.3 (Watts), which is equivalent to 25.2% of the active power required by the single-phase induction asynchronous motor (or shaded pole motor), which required 25 (Watts) to rotate at 1690 (RPM). This translates to 75% lower active power with a 44% superiority in speed, resulting in a 75% savings in single-phase active energy (measured in kWh). The same occurs when comparing it to the universal AC motor (with brushes and wound rotor) to maintain a speed of 3000 (RPM); since it consumes 64.8 (Watts), which is 90.3% more single-phase active energy than that required to achieve the same rotational speed as the permanent magnet synchronous motor (PMSM). The study was conducted on all motors with the same impeller blade diameter and under identical air temperature and atmospheric pressure conditions.

In view of the limitations of the existing eccentricity error separation method of the rotary table, an eccentricity error separation method based on the phase feature of the moiré signal of single reading head is proposed herein. A grating pair transmission model is established based on the analysis of the principle of the rotary table, thereby the influence of eccentricity error on the phase feature of the moiré signal in the rotation course of the rotary table is clarified, and the corresponding model between the phase feature spectral components and the eccentricity error is established. The verification experiments of the proposed method are carried out based on the laboratory-made circuit system. After verifying the accuracy of the data acquisition of the laboratory-made circuit board, the verification experiments of the eccentricity error separation effect of the proposed method are carried out. The experimental data are compared with those of the traditional method and the results show that the error between the two methods is 2.34μm and the relative error is 2.3%.

This Article demonstrates how an eigendecomposition problem is inputted into a quantum circuit, how gates are applied in the quantum circuit, and how the output measurements are the correct eigenvalues. This process is known as quantum phase estimation (QPE). A quantum harmonic oscillator example, a foundational quantum physical chemistry problem, is demonstrated within the context of QPE. A particle in a box example, another quantum physical chemistry problem, may be solved by QPE with a caveat. These examples are of the limiting cases of diagonal matrices. Future advances in taking matrix inverses for solving linear sets of equations or finding ground state energies in the Schrödinger equation will use the principles implemented in this Article.

The majority of current methods for measuring the angular deflection of a laser beam enable measurement only in one selected plane. However, there are tasks in which measurements of laser beam deflections in 3D are required. In this paper, we present a way of enabling two-axial measurements of the deflection of a beam based on a single-axis sensor. The key idea is to direct a laser beam alternately into one of two arms of a measurement system. In the first arm, the beam is transmitted directly to the angular sensor, while in the second, the beam is directed to the sensor via a special optical element that rotates the plane of the beam deflection; in other words, this element changes the deflection in the horizontal plane into a deflection in the vertical plane, and vice versa. To alternate the path of the beam, a variable phase retarder and a polarising beamsplitter are used. The proposed technique is experimentally verified, and the results confirm its effectiveness.

The mechanical properties of α-chitin and chitosan biocomposite are investigated due to their broad range of potential applications in bioengineering, materials science, and environmental technology. Employing molecular dynamics (MD), and stress-strain analyses, this study comprehensively investigates biopolymers mechanical response and anisotropic mechanical behavior under uniaxial tensile loading conditions in an aqueous environment. Our computational models were validated against existing experimental data, showing high degrees of correspondence. Uniaxial tensile tests revealed that α-chitin exhibits a remarkable ultimate tensile strength (UTS) of 10.07 GPa in the crystalline chain direction (y-axis) at a high strain rate of 0.636, compared to a significantly lower UTS of 2.78 GPa in the perpendicular direction (x-axis) at a lower strain rate of 0.066. The biocomposite nanostructure, encompassing randomly distributed chitosan, reduced stiffness, maintaining remarkable flexibility as α-chitin, with a UTS of 5.03 GPa in the y-axis and 2.34 GPa in the x-axis. Further, the directional elastic modules for α-chitin were calculated as 51.76 GPa and 39.76 GPa in the x and y directions, respectively. In contrast, these values for the α-chitin-chitosan biocomposite were estimated as 31.66 GPa and 26.00 GPa, respectively. The findings provide valuable insights into the distinct mechanical properties of α-chitin and chitosan biocomposite, making a substantial contribution to optimizing these materials for specialized applications.

The direct measurements of the magnetocaloric effect were performed in Heusler Ni44.4Mn36.2Sn14.9Cu4.5 alloy at cryogenic temperatures in magnetic fields up to 10 T. The maximum value of the inverse magnetocaloric effect in a field of 10 T was observed ∆Tad = –2.7 K in the vicinity of the 1st order magnetostructural phase transition at T0 = 117 K. The ab initio and Monte Carlo calculations were performed to discuss the effect Cu doping into Ni-Mn-Sn compound on the ground state structural and magnetic properties. It is shown that with increasing Cu content the martensitic transition temperature decreases and the Curie temperature of austenite slightly increases. In general, calculated transition temperatures, magnetization values are correlated well with the experimental ones.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

The efficient extraction of phthalate acid esters (PAEs) is challenging due to their extremely low concentration, complicated matrices and hydrophilicity. Herein, hol-low microspheres, as an ideal coating, possesses significant potential for solid-phase microextraction (SPME) due to their fascinating properties. In this study, multi-walled carbon nanotubes hollow microspheres (MWCNTs-HMs) were utilized as a fiber coating for the SPME of PAEs from tea beverages. MWCNTs-HMs were ob-tained by dissolving the polystyrene (PS) cores with organic solvents. Interestingly, MWCNTs-HMs well maintain the morphology of the precursors MWCNTs@PS. The layer-by-layer (LBL) assembly of MWCNTs on PS microsphere templates was ac-quired through electrostatic interactions. Six PAEs, di-ethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-2-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DOP), were se-lected as target analytes for assessing the efficiency of the coating for SPME. The stirring rate, sample solution pH and extraction time were optimized by using the Box-Behnken design. Under optimal working conditions, the proposed MWCNTs-HMs/SPME was coupled with gas chromatography-tandem mass spec-trometry (GC-MS/MS) to achieve high enrichment factors (118–2137), wide linearity (0.0004-10 μg L-1), low limits of detection (0.00011-0.0026 μg L-1) and acceptable recovery (80.2%-108.5%) for the detection of PAEs. Therefore, the MWCNTs-HMs coated fibers are promising alternatives in the SPME method for the sensitive detec-tion of PAEs at trace levels in tea beverages.

Oral cancer ranks sixth among Taiwan's top 10 cancers, and most patients with poor prognosis acquire metastases. The essential fatty acid alpha-linolenic acid (ALA) has been found to diminish many cancer properties. However, the anti-cancer activity of ALA in oral cancer has yet to be determined. Migration and invasion assays confirmed OSCC cells' EMT capabilities, whereas flow cytometry and Western blotting identified the molecular pathways. ALA dramatically reduced cell growth in a concentration dependent manner, according to the findings. Low concentrations of ALA (100 or 200 μM) inhibit colony formation, expression of Twist and EMT-related proteins, expression of MMP2/-9 proteins and enzyme activity, as well as cell migration and invasion. Treatment with high concentrations of ALA (200 or 400 μM) greatly increases JNK phosphorylation and c-jun nuclear accumulation, then upregulates the FasL/caspase8/caspase3 and Bid/cytochrome c/caspase9/caspase3 pathways, leading to cell death. Low concentrations of ALA inhibit SAS and GNM cell migration and invasion by suppressing Twist and downregulating EMT-related proteins, or by decreasing the protein expression and enzyme activity of MMP-2/-9, whereas high concentrations of ALA promote apoptosis by activating the JNK/FasL/caspase 8/caspase 3-extrinsic pathway and the Bid/cytochrome c/caspase 9 pathway. ALA demonstrates potential as a treatment for OSCC patients.

SPME analysis of the scent Ophrys orchids gave the following results: O. apifera: benzyl benzoate, -copaene, caryophyllene, and cyclosativene. O. crabronifera subsp. biscutella: pentadecene, pentadecane, heptadecane, nonadecane, and heinecosane. O. bertolonii subsp. bertolonii: pentadecane, heptadecane and nonadecane. O. passionis subsp. garganica: i-propyl palmitate, caryophyllene, pentadecane, and heptadecane. O. holosericea subsp. apulica: -copaene, pentadecane, caryophyllene, and heptadecane. O. lacaitae: -copaene, pentadecane, heptadecane, and caryophyllene. O. bombyliflora: cyclosativene, pentadecane, and ethyl dodecanoate. O. insectifera: 8-heptadecene, pentadecane, and heptadecane. O. lutea: heptadecane, 8-heptadecene, nonadecane, and docosane. O. tenthredinifera subsp. neglecta: -copaene, caryophyllene, and i-propyl palmitate.

Background: Non-alcoholic fatty liver disease (NAFLD) is manifested by hepatic steatosis, insulin resistance, hepatocyte death, and systemic inflammation. Obesity induces steatosis and chronic inflammation in the liver. However, the precise mechanism underlying hepatic steatosis in the setting of obesity remains unclear. Here we report studies that address this question. Methods: 14 weeks on high-fat diet (HFD) with high sucrose, C57BL/6 mice revealed a phenotype of liver steatosis. Transcriptional profiling analysis of the liver tissues was performed using RNA sequencing (RNA-seq). Results: Our RNA-seq data revealed 692 differentially expressed genes involved in processes of lipid metabolism, oxidative stress, immune responses, and cell proliferation. Notably, the gene encoding neutral sphingomyelinase SMPD3, was predominantly upregulated in the liver tissues of the mice displaying a phenotype of steatosis. Moreover, nSMase2 activity was elevated in these tissues of the liver. Pharmacological and genetic inhibition of nSMase2 prevented intracellular lipid accumulation and TNFα-induced inflammation in in-vitro HepG2-steatosis cellular model. Furthermore, nSMase2 inhibition ameliorates oxidative damage by rescuing PPARα and prevent cell death associated with high glucose/oleic acid-induced fat accumulation in HepG2 cells. Conclusions: Collectively, our findings highlight the prominent role of nSMase2 in hepatic steatosis which could serve as a potential therapeutic target for NAFLD and other hepatic steatosis-linked disorders.

In this study, we aimed to reveal the proinflammatory effects of serum 25-hydroxyvitamin D3 (Vit D) deficiency and insufficiency in new-onset type 2 diabetes mellitus (T2DM) and prediabe-tes. We recruited 84 prediabetes patients, 94 new-onset T2DM patients and 113 healthy partici-pants. Levels of C-reactive protein (CRP), fibrinogen, ferritin, interleukin-1β (IL-1β), interleu-kin-6 (IL-6), interleukin-8 (IL-8), tumour necrosis factor-α (TNF-α), nuclear factor kappa-B (NF-κB) and mitogen-activated protein kinase (MAPK) were measured in the serum of the par-ticipants. The ANOVA Bonferonni and Kruskal Wallis Dunn tests were used for the comparison of the inflammation markers and vitamin D levels between the groups. Upon covariance analy-sis with age, gender and BMI; Vit D levels of T2DM group were found to be significantly lower (p<0.003). Proinflammatory markers and CRP were found to be significantly higher in predia-betic and diabetic subjects. In the prediabetes group, IL-1β, IL-6, IL-8, TNF-α and MAPK were significantly higher in those with Vit D insufficiency and deficiency groups. In T2DM group, IL-1β, IL-6, IL-8, TNF-α, NF-κB, MAPK and CRP were significantly higher in those with Vit D insufficiency and deficiency. Our study emphasizes the proinflammatory effects of Vit D on the initiation of inflammation in both prediabetes and diabetes mellitus.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Understanding the phenomena underlying the non-selective susceptibility to ischemia of py-ramidal neurons in the CA3 area of the hippocampus is important from the point of view of elu-cidating the mechanisms of memory loss and the development of post-ischemic dementia. We used an ischemic model of Alzheimer's disease to study changes in amyloid protein precursor gene expression, its cleavage enzymes and tau protein in the CA3 area of the hippocampus af-ter a 10-minute brain ischemia with 12, 18, and 24-month survival. Quantitative reverse tran-scriptase PCR assay showed that the expression of all the genes that contribute to amyloid pro-duction was dysregulated within 2 years in the CA3 area of the hippocampus after ischemia. The expression of the amyloid protein precursor gene was above the control values at all times of the study. The expression of the α-secretase gene also exceeded the control values throughout the study. In contrast, the expression of the β-secretase gene reaching its maximum increase 12 months after ischemia, was below control values after 18 months and again above control values after 24 months of survival. Presenilin 1 and 2 gene expression was significantly elevated throughout the follow-up period, with peak expression of both genes occurring 12 months after ischemia. This suggests that the genes studied are involved in the non-amyloidogenic processing of amyloid protein precursor. Also, tau protein gene expression was significantly elevated throughout the observation period, and peak gene expression was present 12 months after is-chemia. Data indicate that an episode of brain ischemia with long-term survival causes damage and death of pyramidal neurons in the CA3 area of the hippocampus in a manner dependent on modified tau protein. Thus defining a new and important mechanism of pyramidal neuronal death in the CA3 area after ischemia. In addition tau protein gene modification after brain is-chemia is useful in identifying ischemic mechanisms occurring in Alzheimer's disease.

An overview of the link between nonequilibrium thermodynamics and complexity theory is offered. It is shown how the rate of entropy production can be quantified through the spectrum of the Lyapunov exponents. It was shown how the entropy production per unit of time meets the necessary and sufficient conditions to be a Lyapunov function and constitutes per se an extremal principle. The entropy production fractal dimension conjecture was established. It is shown how the rate of entropy production as a non-extremal criterion represents an alternative way of sensitivity analysis of differential equations. Finally, an extension to biophysical-chemical systems, on the one hand, the use of the dissipation function is shown, as a thermodynamic potential out of equilibrium, in the characterization of biological phase transitions. On the other hand, it was evidenced how the rate of entropy production represents a physical quantity to evaluate the complexity and robustness of cancer.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

In recent years there has been increasing interest in the discovery of new natural herbal remedies for the treatment of common conditions such as diabetes and inflammatory diseases. In this context, this paper analyzed the antidiabetic and anti-inflammatory potential of two plants of the genus Artemisia: Artemisia absinthium (wormwood) and Artemisia vulgaris (mugwort) and Trigonella foenum-graecum (fenugreek) plants less studied from this point of view. Thus, hydroal-coholic extracts (50% EtOH v/v, 10% mass) were made, which were processed by membrane technologies, micro- and ultrafiltration, in order to concentrate the biologically active principles. The extracts were then analyzed in terms of content in active principles of interest (polyphenols, flavones). The antidiabetic activity of the extracts was analyzed by testing their ability to inhibit α-amylase and α-glucosidase and the anti-inflammatory activity by testing the ability to inhibit hyaluronidase (HYA) and lipoxygenase (LOX). Thus, the T. foenum-graecum extracts showed a high inhibitory activity on α-amylase 3.22 ± 0.3 g / mL (compared to the standard used - IC50 acarbose = 3.5 g / mL) and a high inhibitory activity on LOX: 19.69 ± 0.52 g/mL (compared to all standards used). The concentrated extract of Artemisia vulgaris showed increased activity of inhibition of α-amylase - IC50 = 8.57 ± 2.31g/mL and moderate activity of inhibition of HYA - IC50 = 17.18 g/mL compared to ibuprofen, the standard used - IC50 = 5.73 g/mL. The concentrated extract of Artemisia absinthium showed a pronounced activity of inhibition of LOX - IC50 = 19.71 g / mL, compared to the standard - rutin - IC50 = 22.34 g/mL).

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

A series of novel substituted isoxazolidine derivatives was synthesized through 1,3-dipolar cycloaddition reactions of α-aryl-N-methyl nitrones with various ethylene moieties, resulting in the formation of isoxazolidine derivatives. The structures of the synthesized compounds were characterized using spectroscopic methods. The [3+2] cycloaddition (32CA) reactions of α-aryl-N-methyl nitrones with diverse ethylene substituents were computed employing Density Functional Theory (DFT) at the B3LYP/6–31G(d) level, upgrading bond parameters. An investigation of the electron localization function (ELF) unveiled the zwitterionic nature of α-aryl-N-methyl nitrones, devoid of pseudoradical or carbenoid centers. Utilization of CDFT indices enabled the prediction of global electronic flux from the strongly nucleophilic α-aryl-N-methyl nitrones to the varied electrophilic ethylene functionalities. Molecular docking and molecular dynamics simulations were conducted on the isoxazolidine derivatives against the EGFR receptor (PDB: 4ZAU). In silico assessment of the synthesized isoxazolidines involved molecular docking, wherein the compound with the highest docking score was subjected to molecular dynamics simulations. Compound 11a, out of the thirty isoxazolidine derivatives, displayed the most substantial binding energy, yielding a g score of -6.57 kcal/mol. These observations highlighted the functional role of amide NH2 and NO2 in the binding process with the target protein, influencing its activity. Furthermore, prediction of ADME drug-likeness properties was performed to identify a suitable candidate.

In the theoretical treatment of crystallization it is commonly assumed that relaxation processes of the liquid proceed fast as compared to crystal nucleation and growth processes. Actually, it is supposed that the liquid is located always in the metastable state corresponding to the current values of pressure and temperature. However, near and below the glass transition temperature, Tg, this condition is commonly not fulfilled. In such cases, in the treatment of crystallization, deviations of the state of the liquid from the respective metastable equilibrium state have to be accounted for in determining the kinetic coefficients governing the crystallization kinetics, the thermodynamic driving force of crystallization, and the surface tension of the aggregates of the newly evolving crystal phase including the surface tension of critical clusters affecting considerably the crystal nucleation rate. These factors may considerably influence the course of the overall crystallization process. A theoretical analysis of the resulting effects is given in the present paper by numerical solutions of the J(ohnson)–M(ehl)–A(vrami)–K(olmogorov)–equation employed as the tool to model the overall crystallization kinetics and by analytical estimates of the crystallization peak temperatures in dependence on cooling and heating rates. The results are shown to be in good agreement with experimental data. Possible extensions of the theory to be explored in future analysis are anticipated.

The development of mineral resources in China has gradually entered the stage of deep mining. Rock burst, collapse and other ground pressure disasters caused by deep high stress have become major hidden dangers restricting mine safety production. Microseismic monitoring technology is an important means of ground pressure risk prediction. In this paper, the wavelet coefficient threshold denoising method in time-frequency domain, STA/LTA method, AIC method, Skew and Kurtosis method are studied, and the automatic P-phase onset time picking model based on noise reduction and multiple detection indexes is established. Through the effect analysis of microseismic signals collected by microseismic monitoring system of coral Tungsten Mine in Guangxi, automatic P-phase onset time picking is realized. the reliability of the P-phase onset time picking method proposed in this paper based on noise reduction and multiple detection indexes is verified. The picking accuracy can still be guaranteed under the severe signal interference of background noise, power frequency interference and manual activity underground mine, Which is of great significance to the data processing and analysis of microseismic monitoring.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. A doping-induced and concentration-dependent phase transition in ZrO₂ under the influence of Y₂O₃ was discovered, due to which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The results show that ab initio approaches are able to describe the mechanism of doping-induced phase transitions in (ZrO₂+Y₂O₃)-like systems, based on which it can be assumed that DFT calculations can also flawlessly evaluate other physical and chemical properties of YSZ, which have not yet been studied quantum chemical research. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Outbreaks of the desert locust Schistocerca gregaria affect some of the poorest parts of Africa, causing devastating catastrophes. Key to understanding and dealing with this problematic adaptation to environmental changes is comparing locusts that are gregarious (associated with outbreak states) and solitarious (associated with non-outbreak states) either in nature or after experimental treatments in laboratories. Categorising locusts and detecting changes in their phase status is key to such comparisons. Such comparisons are hitherto based on applying mathematical models that use behavioural parameters and that each laboratory has to build a new for each experiment. All such models used thus far for research on locusts are different from each other. That implies differences in the tools used for the different experiments and by the different laboratories and, thus, potential noise in the scientific results and interpretations too. Standardizing the way how we categorise locusts between laboratories and experiments is needed if we want to reduce noise and errors. It is even a must if we are to make the results and interpretations transferable and comparable between experiments and laboratories that work in such an important research area. Here, we use samples from independent S. gregaria population in order to further test the two models that were suggested earlier as standardizing tools for S. gregaria categorization. The outcomes of both models were largely replicated and reproducible. We report on how successful the two models were at categorizing solitarious, intermediate (transient) and gregarious nymph and adult samples. We highlight shortcomings and make more specific recommendations on the use of these models based on the differences they show as to their precision when categorizing the solitarious and gregarious S. gregaria nymph and adult samples.

The extraction method for simultaneously analyzing fatty acids (Myristic acid, cis-Palmitvaccenic acid, Palmitic acid, Palmitic-9,9-d2 acid, Oleic acid, Stearic acid and Stearic-2,2-d2 acid) related to biodiesel fuel in large algae was developed. The introduction of trimethylaminoethyl (TMAE) derivatives into the hydroxyl group (-OH) functional group of the analyte was able to improve ionization and obtain high sensitivity. Liquid Chromatography (LC) was used to investigate the optimal mobile phase composition and flow rate for the separation of five derived fatty acids. In this study, a solid phase extraction (SPE) column was introduced for efficient extraction of fatty acids, and the optimal conditions for SPE were set by comparing the recovery rate according to the solvent for each step (loading, washing, and elution) of SPE from macroalgae.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

The research community has shown significant interest in the aqueous synthesis of nanomaterials due to its ability to eliminate the need for complex organic solvents. This synthesis approach aligns with the principles of green chemistry, attracting considerable attention. Aqueous solution technology in fabricating nanostructures has gained recognition for its potential to create ultrasensitive, low-energy, and ultrafast optoelectronic devices. This report focuses on synthesizing lead iodide (PbI2) nanoplates using a water-based solution technique and fabricating a planar photodetector. The photodetectors with a planar type of device structure (ITO/PbI2 NPs/Au) demonstrated a remarkable photosensitivity of 3.9×103 and a photoresponsivity of 0.51 mA/W at a wavelength of 405 nm. Notably, the asymmetrical output properties of ITO/PbI2 NPs/Au detector deliver additional evidence of the effective creation of a Schottky contact. Thus, the photodetector exhibited a photoresponse even at 0 V bias, leading to the realization of self-powered photodetectors. Additionally, the device exhibited a rapid photoresponse of 0.21/0.38 s (−5 V) in the visible range. This study has expanded the horizons for the aqueous-phase synthesis of nanoplate nanostructures, enabling the large-area fabrication of high-performance photodetectors.

Using straightforward and cost-effective methods, persimmon leaves were converted into a high-quality powder. This powder was applied as an adsorbent for the removal of Cu(II) and Cd(II) from aqueous solutions. Scanning electron microscopy (SEM) indicated the presence of particles with non-homogeneous sizes and rough texture. Elemental analysis and the EDX technique confirmed the presence of elements such as sulfur, phosphorus, nitrogen, and oxygen. The results of ¹³C nuclear magnetic resonance (¹³C-NMR), obtained through the cross-polarization technique, suggest the presence of groups containing sulfur and oxygen. Infrared spectroscopy (FTIR) indicated the existence of amine and hydroxyl groups. The material was used in solid-phase extraction of Cu(II) and Cd(II) in batch experiments, and its adsorption capacity was evaluated as a function of time, pH, and analyte concentration. Kinetic equilibrium was reached within 5 minutes, and the experimental data were fitted to the pseudo-second-order kinetic model. The optimum pH for adsorption of both metal species was observed to be around 5.0. The adsorption isotherms were adjusted using the modified Langmuir equation, and the maximum amount of metal species extracted from the solution was determined to be 0.213 mmol g^-1 for Cu(II) and 0.215 mmol g^-1 for Cd(II), with high linear correlation coefficients for both metals. The persimmon leaves are typically abundant during the growing season, and since they are seasonal, the Diospyros kaki L.f. tree undergoes the natural process of leaf abscission, ensuring the availability of leaves for application.

By making periodic thru-holes in a suspended film, the phonon system can be modified. Motivated by the BCS theory, the technique -- so-called phonon engineering -- was applied to a metallic niobium sheet. It was found that its electrical resistance dropped to zero at 175 K, and the zero-resistance state persisted up to 290 K in the subsequent warming process. Despite the initial motivation, neither these high transition temperatures nor the phase transition with thermal hysteresis can be accounted for by the BCS theory. Therefore, we abandon the BCS theory. Instead, it turns out that the metallic holey sheet is partly oxidized to form a niobium-oxygen square lattice, which has points of resemblance to a copper-oxygen plane, the fundamental component of cuprate high-T_c superconductors. Therefore, the pairing mechanism underlying this study should be related to that of cuprate high-T_c superconductors, which we may not yet understand. In addition to the electrical results of zero resistance, the holey sheet exhibited a decrease in magnetization upon cooling, i.e., the Meissner effect. Moreover, the remnant magnetization was clearly detected at 300 K, which can only be attributed to persistent currents flowing in a superconducting sample. Thus, this study meets the established criteria for a conclusive demonstration of true superconductivity. Finally, the superconducting transition with the unambiguous thermal hysteresis is discussed. According to Halperin, Lubensky, and Ma, or HLM for short, any superconducting transition must always be first order with thermal hysteresis because of the intrinsic fluctuating magnetic field. The HLM theory is very compatible with the highly oriented system harboring two-dimensional superconductivity.

Alginate-gelatin hydrogels are extensively used in bioengineering. However, despite different formulations being utilized for growing different cell types in vitro, their pH and its effect, together with the crosslinking ions, of those formulations are still infrequently assessed. In this work we studied how these elements can affect hydrogel stability and printability and influence U2OS and NIH/3T3 cell viability and metabolism on the resulting 3D prints. In this context, 6% alginate + 2% gelatin hydrogels were prepared with 0.1 M MES buffer with pH 5.5, 6.5, 7.0 or 8.0, printed by extrusion-based 3D printing, and crosslinked immediately after printing with either CaCl2 or BaCl2. Our results showed that both the buffer pH and the crosslinking ion (Ca2+ or Ba2+) influence the swelling and degradation rates of the prints. Moreover, the buffer pH influenced the printability of the hydrogel in air, but when printed directly in a fluid-phase CaCl2 or BaCl2 crosslinking bath. In addition, both U2OS and NIH/3T3 cells showed greater cell metabolic activity on one-layer prints crosslinked with Ca2+. Besides, Ba2+ increased cell death of NIH/3T3 cells while had no effect on the U2OS cell viability. The pH of the buffer also caused an important impact on the cell behaviour. U2OS cells showed a 2.25-fold cell metabolism increase on one-layer prints prepared at pH 8.0 in comparison to those prepared at pH 5.5. Whereas, NIH/3T3 cells showed greater metabolism on one-layer prints with pH 7.0. Finally, we observed a difference on cell arrangement of the U2OS cells growing on prints prepared from hydrogels with acidic buffer in comparison to cells growing on those prepared using neutral or basic buffer. These results show that both pH and crosslinking ion influence hydrogel strength and cell behaviour.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

Consciousness is a special type of interaction between subjects exchanging by lingua quanta (phonemes). A set of lingua quanta composes a thesaurus placed on the edge of chaos. Its library is a memory, modification of which is due to tuning of memristive neural elements scattered in the brain volume. The memristive neural model takes into consideration two types of neurons - excitatory and inhibitory and the current leakage, all at the body temperature, T = 309 K. At such temperatures only heavy ions like hydrogen ions - protons can pass robustly through the water medium of the brain. The robust ion transport is proton water wires supported by the Grotthuss mechanism. Final aims of the ions are the gap junctions (electric synapses) linking nearest neurons. Following these observations, a model of excitable nervous tissue is constructed. Namely, a difference mapping on the basis of sigmoid curves can reproduce chaotic modes of neural activity proved by positive values of the Lyapunov exponent. The edge of chaos is placed near the bifurcation boundary dividing the chaos and the periodic convulsive activity typical at the epileptic discharges. In this region the self-sustained spiral waves occur. An intermittent activity of the competing excitatory and inhibitory neurons is observed on the edge of chaos. The intermittent electrical activity of neural tissues is demonstrated by records both from different literature issues and records made by the author together with DR. A. Dudkin on slices of CA1 field of the hippocampus.

Deep neural networks (DNNs) have gained prominence in addressing regression problems, offering versatile architectural designs that cater to various applications. In the field of earthquake engineering, seismic response prediction is a critical area of study. Simplified models such as single-degree-of-freedom (SDOF) and multi-degree-of-freedom (MDOF) systems have traditionally provided valuable insights into structural behavior, known for their computational efficiency facilitating faster simulations. However, these models have notable limitations in capturing the nuanced nonlinear behavior of structures and the spatial variability of ground motions. This study focuses on leveraging ambient vibration (AV) measurements of buildings, combined with earthquake (EQ) time-history data, to create a predictive model using a neural network (NN) in image format. The primary objective is to predict a specific building's earthquake response accurately. The training dataset consists of 1,197 MDOF 2D shear models, generating a total of 32,319 training samples. To evaluate the performance of the proposed model, termed MLPER (Machine Learning based Prediction of building structures' Earthquake Response), several metrics are employed. These include mean absolute percentage error (MAPE) and mean deviation angle (MDA) for comparisons in the time domain. Additionally, we assess magnitude-squared coherence values and phase differences (Δφ) for comparisons in the frequency domain. This study underscores the potential of MLPER as a reliable tool for predicting building earthquake response, addressing the limitations of simplified models. By integrating AV measurements and EQ time-history data into a neural network framework, MLPER offers a promising avenue for enhancing our understanding of structural behavior during seismic events, ultimately contributing to improved earthquake resilience in building design and engineering.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

The phenomenon of ordered self-assembly on solid substrates is a topic of interest in both fundamental surface science research and its applications in nanotechnology. The regulation and control of two-dimensional (2D) self-assembled supra-molecular structures on surfaces have been realized through applying external stimuli. By utilizing scanning tunneling microscopy (STM), researchers can investigate detailed phase transition process about self-assembled monolayers (SAMs), providing insight into the interplay between intermolecular weak interactions and substrate-molecule interactions, which govern the formation of molecular self-assembly. This review will discuss the structural transition of self-assembly probed by STM in response to external stimuli and provide state-of-art methods such as tip induced confinement for the alignment of SAM domains and selective chirality. Finally, we discuss the challenges and opportunities in the field of self-assembly and STM.

Self-phase modulation (SPM) broadening of laser spectra was studied in a transmission mode in natural and synthetic diamonds at variable laser wavelengths (515 and 1030 nm), pulse energies and widths (0.3 - 12 ps, positively chirped pulses), providing their filamentary propagation. Besides the monotonous SPM broadening of the laser spectra versus pulse energy, more pronounced for the (sub)picosecond pulsewiths and more doped natural diamond, periodical low-frequency modulation was observed in the spectra at the shorter laser pulsewidths, indicating dynamic Bragg filtering of the supercontinuum due to ultrafast plasma and nanoplasmonic effects. Damping of broadening and ultramodulation for the longer picosecond pulsewidths was related to thermalized electron-hole plasma regime established for the laser pulsewidths longer, than 2 ps. Unexpectedly, at higher pulse energies and corresponding longer microfilaments, the number of spectral modulation features increases, indicating dynamic variation of the periods in the longitudinal plasma Bragg gratings along the filaments due to prompt secondary laser-plasmon interactions.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

We address weighted composition operators ψCφ from α-Bloch spaces to Bers-type spaces of bounded holomorphic functions on Y, where Y is a generalized Hua domain of the first kind, and obtain some necessary and sufficient conditions for the boundedness and compactness of those operators.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Many biological functions of curcumin have been reported. As certain bioactivities of curcumin are eliminated by antioxidants, reactive oxygen species generated by curcumin have been suggested as a relevant mechanism. In the present study, effects of different types of antioxidants on stability and bioactivities of curcumin were analyzed. High concentrations (>4mM) of the thiol antioxidants including N-acetylcysteine (NAC), glutathione (GSH) and β-mercaptoethanol accelerated decomposition of curcumin and other curcuminoids; Submillimolar levels (<0.5 mM) of GSH and NAC rather improved their stability. Ascorbic acid or superoxide dismutase also stabilized curcumin regardless of their concentration. Cellular levels and bioactivities of curcumin including cytotoxicity and induction of heme oxygenase-1 were significantly reduced in the presence of 8 mM of GSH and NAC. The effects were enhanced in the presence of submillilmolar GSH and NAC, or non-thiol antioxidants. The present results indicate that antioxidants with reduced thiol group could directly interact with α, β-unsaturated carbonyl moiety of curcuminoids and modulate their stability and bioactivity.

The β-thalassemias are hereditary monogenic diseases characterized by low or absent production of adult hemoglobin and excess in the content of α-globin. This excess is cytotoxic for the erythroid cells and responsible of the β-thalassemia associated ineffective erythropoiesis. Therefore, the decrease of α-globin excess is a relevant clinical effect for these patients and can be obtained by induction of fetal hemoglobin, by autophagy, or both. The in vivo effects of sirolimus (rapamycin) and analogues on induction of fetal hemoglobin (HbF) is of key importance for therapeutic protocols in a variety of hemoglobinopathies, including β-thalassemia. In this research communication, we report data showing that decrease of autophagy-associated p62 protein, increased expression of ULK-1 and reduction of the excess of α-globin is operating in erythroid precursors (ErPCs) stimulated in vitro with low dosages of sirolimus. In addition, increased ULK-1 mRNA content and decrease of α-globin content were found in ErPCs isolated from β-thalassemia patients recruited for the NCT03877809 clinical trial and treated with 0.5-2 mg/day sirolimus. Our data support the concept that autophagy, ULK1 expression and α-globin chain reduction should be considered important endpoints in sirolimus-based clinical trials for β-thalassemia.

Andrographis paniculata leaves have been widely used in traditional medicine due to their rich content of phenolic compounds. In this study, we evaluated the total phenolic and flavonoid content of Andrographis paniculata leaf extracts (ALE), as well as its antioxidant activities against DPPH, ABTS, and hydrogen peroxide radicals. Additionally, we conducted cell viability assays, RT-PCR, and western blot analysis to investigate the biochemical effects of ALE on UVB-induced HaCaT cells. Our results revealed that ALE exhibited a high concentration of polyphenols and flavonoids, which were associated with potent abiotic antioxidant properties. Furthermore, ALE treatment effectively abrogated the damage caused by UVB radiation on key molecules such as hyaluronan synthase 1, Aquaporin 3, and loricrin in HaCaT cells. ALE also demonstrated the ability to reduce the overactivation of mitogen-activated protein kinases (MAPKs) and the expression of pro-inflammatory cytokines, including interleukin-6 and interleukin-1β in UVB-induced HaCaT cells. Additionally, ALE positively influenced the peroxisome proliferator-activated receptor alpha in these cells. Overall, our findings highlight the antioxidant and anti-inflammatory effects of ALE, as well as its significant role in modulating skin barrier functions. These results contribute to the growing body of evidence supporting the therapeutic potential of ALE in skincare and dermatological applications.

Covariant integral quantization with rotational symmetry SO(3) is established for the quantum motion on this group manifold, or, alternatively, for Gabor signal analysis on this group. We revisit the action of the related (non-unitary) Weyl-Gabor operator on the Hilbert space of square integrable functions on SO(3) and disclose a set of various properties. By selecting weight functions on the corresponding discrete-continuous phase space, one derives related coherent states and Wigner transform.

An atomic-scale approach is employed to simulate the formation of precipitates with different lattice misfits in the early stages of aging of supersaturated aluminum alloys. Simulation results reveal that the increase of lattice misfit could significantly promote the nucleation rate of precipitates, which results in a larger number and smaller size of the precipitates. The morphologies of the precipitates also vary with the degree of lattice misfit. Moreover, the higher the lattice misfit, the earlier the nucleation of the second phase occurs, which can substantially inhibit the movement of dislocations. The research on the lattice misfit of precipitation can provide theoretical guidance for the design of high-strength aluminum alloy.

Cellular biomolecular condensates termed ribonucleoprotein (RNP) granules often are enriched in messenger RNA (mRNA) molecules relative to the surrounding cytoplasm. Yet, the spatial localization and diffusion of mRNAs in close proximity to phase separated RNP granules is not well understood. In this study, we performed single molecule fluorescence imaging experiments of mRNAs in live cells in the presence of two types of RNP granules, stress granules (SG) and processing bodies (PB), which are distinct in their molecular composition and function. We developed a photobleaching- and noise-corrected colocalization imaging algorithm that was employed to determine the accurate positions of individual mRNAs relative to the granule’s boundaries. We found that mRNAs are often localized at granule boundaries, an observation consistent with recently published data. We suggest that mRNA molecules become spontaneously confined at the RNP granule boundary similar to the adsorption of polymer molecules at liquid-liquid interfaces, which is observed in various technological and biological processes. We also suggest that this confinement could be due to a combination of intermolecular interactions associated with, first, the screening of a portion of the RNP granule interface by the polymer and, second, electrostatic interactions due to a strong electric field induced by a Donnan potential generated across the thin interface.

Continuous-variable quantum key distribution (CV-QKD) shows potential for the rapid development of an information-theoretic secure global communications network; however, the complexities of CV-QKD implementation remain a restrictive factor. Machine learning (ML) has recently shown promise in alleviating these complexities. ML has been applied to almost every stage of CV-QKD protocols, including ML-assisted phase error estimation, excess noise estimation, state discrimination, parameter estimation and optimization, key sifting, information reconciliation, and key rate estimation. This survey provides a comprehensive analysis of the current literature on ML-assisted CV-QKD. In addition, the survey compares the ML algorithms assisting CV-QKD with the traditional algorithms they aim to augment, as well as providing recommendations for future directions for ML-assisted CV-QKD research.

Acute lymphoblastic leukemia (ALL) is the most common childhood cancer. Although prognosis continually improved along years, a significant proportion of patients still relapse from the disease due to leukemia resistance to therapy. Methotrexate (MTX), a folic acid antagonist, is a chemotherapy agent commonly used against ALL and a immune-system suppressant for rheumatoid arthritis, that presents multiple and complex mechanisms of action and resistance. Previous studies have shown that MTX modulates the nuclear factor kappa B (NF-κB) pathway, an important family of transcription factors involved in inflammation, immunity, cell survival, and proliferation, frequently hyperactivated in ALL. Using gene set enrichment analysis (GSEA) on publicly available gene expression data from 161 newly diagnosed pediatric ALL patients, we found “TNF-α signaling pathway” to be the most enriched Cancer Hallmark in MTX poor responder patients. Transcriptomic analysis in a panel of ALL cell lines (6 BCP-ALL and 7 T-ALL) also identified the same pathway as differentially enriched among MTX resistant cell lines, as well as in slowly dividing cells. To better understand the crosstalk between NF-κB activity and MTX resistance, we genetically modified the cell lines to express luciferase under a NF-κB biding site promoter. We observed that the fold change in NF-κB activity triggered by TNF-α (but not MTX) treatment correlated with MTX resistance and proliferation across the lines. At the individual gene level, NFKB1 expression was directly associated with a poorer clinical response to MTX, and with both an increased TNF-α-triggered NF-κB activation and MTX resistance in the cell lines. Despite these results, pharmacological inhibition (with BAY 11-7082 and parthenolide) or stimulation (with exogenous TNF-α supplementation) of the NF-κB pathway did not alter MTX resistance of the cell lines significantly, evidencing a complex interplay between MTX and NF-κB in ALL.

Oxidative stress-mediated damage is often a downstream result of Parkinson’s disease (PD), which is marked by sharp decline in dopaminergic neurons within the nigrostriatal regions of the brain, accounting for the symptomatic motor deficits in patients. Regulating the level of oxidative stress may present a beneficial approach in preventing PD pathology. Here, we assessed the efficacy of a nicotinamide adenine phosphate (NADPH) oxidase (NOX) inhibitor, an exogenous reactive oxygen species (ROS) regulator synthesized by Aptabio therapeutics with the specificity to NOX-1, 2, and 4. Utilizing N27 rat dopaminergic cells and C57Bl/6 mice, we confirmed that the exposures of alpha-synuclein preformed fibrils (PFF) induced protein aggregation, a hallmark in PD pathology. In vitro assessment of the novel compound revealed an increase in cell viability and decreases in cytotoxicity, ROS, and protein aggregation (Thioflavin-T stain) against PFF exposure at the optimal concentration of 10nM. Concomitantly, the oral treatment alleviated motor deficits in behavioral tests, such as hindlimb clasping, rotarod, pole, nesting, and grooming test, via reducing protein aggregation, based on rescued dopaminergic neuronal loss. The suppression of NOX-1, 2, and 4 within the striatum and ventral midbrain regions including SNc contributed to neuroprotective/recovery effects, making it a potential therapeutic option for PD.

The mechanism of vapor-gas deposition of vinyltrimethoxysilane (VS) and ethylene glycol (EG) from azeotropic solutions is investigated, which allows to reduce the evaporation temperature of the components of working mixtures. The need for such studies is associated with the development of a new direction in the technology of vapor-gas deposition of polymer coatings. Methods have been developed for monitoring the chemical composition of working solutions in evaporators using optical spectroscopy, which allow calculating the partial pressures of vapor phase components. Based on these studies, compositions of working solutions are proposed that allow to equalize the partial pressures of the components of working mixtures with a large difference in boiling point. A new method of vapor-gas deposition of non-volatile powder inhibitors on metals is proposed. Chemical compositions of siloxane coatings were determined using XPS and mechanisms of interaction of VS with polymerization promoters ethylene glycol and 1-hydroxy ethylidene-1,1-diphosphonic acid (HEDP) were proposed.

In this paper, we consider the one-dimensional Ising model (shortly, 1D-MSIM) having mixed spin-(s,(2t−1)/2) with nearest neighbors and the external magnetic field. We establish the partition function of the model by means of the transfer matrix. Under a null boundary condition, we compute certain thermodynamic quantities for the 1D-MSIM. We find some precise formulas to determine the model’s free energy, entropy, magnetization, and susceptibility. By examining the model’s associated iterative equations, we use the cavity approach to investigate the phase transition problem. We numerically determine the model’s periodicity.

MoS2 has long been considered as a promising catalyst for hydrogen production. At present, there are many strategies to further improve its catalytic performance, such as edge engineering, defect engineering, phase engineering and so on. However, at present, there is still a great deal of controversy about the mechanism of MoS2 catalytic hydrogen production. For example, it is generally believed that the base plane of MoS2 is inert, but it has been reported that the inert base plane can undergo a transient phase transition in the catalytic process to play the catalytic role, which is contrary to the common understanding that the catalytic activity is only at the edge. Therefore, it is necessary to further understand the mechanism of MoS2 catalytic hydrogen production. In this article, we summarized the latest research progress on the catalytic hydrogen production of MoS2, which is of great significance for revisited the mechanism of MoS2 catalytic hydrogen production.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

We investigate numerically the interactions of in-phase Airy beams modulated by a fundamental Gaussian beam and fourth-order diffraction in Kerr nonlinear media. Directly numerical simulations show that normal (anomalous) fourth-order diffractions and in-phase (out-of-phase) Gaussian beam affect the interactions of solitons generated from Airy beams in unique manners. Different from previous results that interactions between in-phase (out-of-phase) conventional beams are always attractive (repulsive), many anomalous interactions of Airy beams are obtained. Stable bound states of breathing Airy soliton pairs can be formed with the help of fourth-order diffraction and fundamental Gaussian beam.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

Beef meat production in Uruguay is based on pasture or concentrate feeding systems, leading to differences in meat quality. The objective of this study was to compare the oxidative and color stability during refrigerated retail display of beef meat from these two systems. For this, ten Aberdeen Angus steers were reared and fed on pasture and other ten were finished on a concentrate diet. After slaughter, the Semimembranosus muscle was cut into slices and put in a refrigerated showcase for 3, 6, and 9 days simulating commercial conditions. The β-carotene, α-tocopherol, and fatty acid content were determined before the display, and the lipid and protein oxidation, color parameters, and heme iron content were determined before and during the display. Meat from steers fed pasture had a lower content of intramuscular fat, monounsaturated fatty acids, n-6/n-3 ratio, lipid and protein oxidation, L* and a* values, and a higher content of linolenic acid, DHA, total n-3, β-carotene, and α-tocopherol. In conclusion, meat from pasture-fed steers was more stable during the retail display, which can probably be explained by a higher content of antioxidant compounds, such as β-carotene and α-tocopherol, and presented a healthier fatty acid profile.

The Chen circuit system, a three-dimensional autonomous system with intriguing dynamics, has gained considerable attention due to its potential applications in diverse scientific fields. In this article, a Chen circuit-like system is defined and a comprehensive dynamics has been studied. The system exhibits chaotic dynamics, limit cycles, and bifurcations, making it a captivating subject of study. By employing numerical simulations and analytical techniques, we explore the system's stability and identify critical parameter values leading to qualitative changes. Notably, we delve Hopf bifurcations, which give rise to stability changes and the emergence of limit cycles. Furthermore, we analyze the fractal dimension of the system's attractor, providing insights into its complexity and self-similarity. Through a systematic examination of the Chen circuit-like system, we deepen our understanding of its intricate dynamics and offer valuable insights into the underlying mechanisms. The findings contribute to the field of dynamical systems and hold potential implications in areas such as chaos-based secure communications, signal processing, and nonlinear control. This work serves as a valuable reference for researchers and practitioners interested in the dynamics and bifurcation analysis of nonlinear systems.

Physical layer secret key (SK) generation is known to be an efficient means to achieve high secrecy rate, on the condition that dynamic channel state information (CSI) is provided. For this reason, the secrecy performance is highly degraded in a static environment. The intelligent reflecting surface (IRS) is a promising solution to create dynamic randomness, and thus lead to enhanced secrecy performance regardless of the user environments. This paper proposes an IRS-assisted physical layer SK generation scheme, by efficiently combing phase information of the direct and reflected channel information in a hybrid way. In particular, the initial SKs are obtained by adopting efficient phase quantization method with symmetric bit allocation to complex numbered channel estimates. Simulation results show that the proposed hybrid phase quantization (PQ) can improve the SK generation rate and the key disagreement probability in a static environment.

This study reports the development of a numerical method to simulate two-phase flows of Newtonian fluids that are incompressible, immiscible, and isothermal. The interface in the simulation was located and reconstructed using the geometric volume of fluid (VOF) method. The implementation of the Piecewise-Linear Interface Calculation (PLIC) scheme of the VOF method was performed to solve the three-dimensional (3D) interface transport during the dynamics of two-phase flows. In this method, the interface is approximated by a line segment in each interfacial cell. The balance of forces at the interface was accounted for using the continuum interfacial force (CSF) model. To solve the Navier-Stokes equations, meshless finite difference schemes from the HiG-Flow computational fluid dynamics software were employed. The 3D PLIC-VOF HiG-Flow algorithm was used to simulate several benchmark two-phase flows for the purpose of validating the numerical implementation. First, the performance of the PLIC implementation was evaluated by conducting two standard advection numerical tests: the 3D shearing flow test and the 3D deforming field test. Good agreement is obtained for the 3D interface shape using both the 3D PLIC-VOF HiG-Flow algorithm and those found on the scientific literature. In addition, the absolute error of the volume tracking advection calculation obtained by our 3D PLIC-VOF HiG-Flow algorithm was found to be smaller than the one found in the scientific literature for both the 3D shearing and 3D deforming flow tests. Lastly, the 3D bubble rising problem was simulated for different fluid densities and viscosity’s ratios. Again, good agreement is obtained for the 3D interface shape using both the newly implemented algorithm and the OpenFOAM, DROPS and NaSt3D software. The bubble’s rise velocity and evolution of the bubble’s center of mass is also computed with the 3D PLIC-VOF HiG-Flow algorithm and found to be in agreement with these software.

Microarray patches (MAPs) have the potential to be a safer, more acceptable, easier to use, and more cost-effective means for the administration of vaccines than injection by needle and syringe. Here, we report findings from a randomized, partially double-blind, placebo-controlled Phase I trial using the Vaxxas high-density MAP (HD-MAP) to deliver a measles rubella (MR) vaccine. Healthy adults (N = 63, age 18–50 years) were randomly assigned 1:1:1:1 to four groups: uncoated (placebo) HD-MAPs, low-dose MR HD-MAPs (~3,100 median cell-culture infectious dose [CCID50] measles, ~4,300 CCID50 rubella); high dose MR-HD-MAPs (~9,300 CCID50 measles, ~12,900 CCID50 rubella); or a sub-cutaneous (SC) injection of an approved MR vaccine, MR-Vac (≥1,000 CCID50 per virus). The MR vaccines were stable and remained viable on HD-MAPs when stored at 2–8°C for at least 24 months. When MR HD-MAPs stored at 2–8°C for 24 months were transferred to 40°C for 3 days in a controlled temperature excursion, loss of potency was minimal, and MR HD-MAPs still met World Health Organisation (WHO) specifications. MR HD-MAP vaccination was safe and well-tolerated; any systemic or local adverse events (AEs) were mild or moderate. Similar levels of binding and neutralizing antibodies to measles and rubella were induced by low-dose and high-dose MR HD-MAPs and MR-Vac. The neutralizing antibody seroconversion rates at day 28 after vaccination for the low-dose HD-MAP, high-dose HD-MAP and MR-Vac groups were 37.5%, 18.8% and 35.7% respectively for measles and 37.5%, 25.0% and 35.7% respectively for rubella. Most participants were seropositive for measles and rubella antibodies at baseline, which appeared to negatively impact the number of participants that seroconverted to vaccines delivered by either route. The data reported here suggest HD-MAPs could be a valuable means for delivering MR-vaccine to hard-to-reach populations and support further development. Clinical trial registry number: ACTRN12621000820808.

(1) Background: Surgical phases form the basic building blocks for surgical skill assessment, feedback and teaching. Phase duration itself and its correlation to clinical parameters has not yet been investigated. Novel commercial platforms provide phase indications but have not been assessed for accuracy yet. (2) Methods: We assess 100 robot-assisted partial nephrectomy videos for phase duration based on previously defined proficiency metrics. We develop an annotation framework and subsequently compare our annotations to an existing commercial solution (Touch Surgery, Medtronic™). We subsequently explore clinical correlations between phase durations and peri-operative parameters. (3) Results: Objective and uniform phase assessment requires precise definitions derived from an iterative revision process. Comparison to a commercial solution shows large differences in definitions across phases. BMI and duration of renal tumor identification correlate positively, as well as tumor complexity and both tumor excision and renorraphy duration. (4) Conclusions: Surgical phase duration can be correlated with certain clinical outcomes. Further research should investigate if retrieved correlations are also clinically meaningful. This requires increasing dataset sizes and facilitation through intelligent computer vision algorithms. Commercial platforms can facilitate this dataset expansion and help unlock the full potential, provided the disclosure of phase annotation details.

Accurately predicting electrical signals of three-phase Direct Torque Control (DTC) induction motors is crucial for optimal motor performance and effective condition monitoring. However, multiple DTC motors’ complexity and operating conditions’ variations pose challenges for traditional prediction methods. To overcome these challenges, we propose an innovative approach that combines Fast Fourier Transform (FFT) to transform electrical motor simulation data and a Bi-directional Long Short-Term Memory (Bi-LSTM) network to forecast processed motor data. By transforming the DTC induction motor signals from the time domain to the frequency domain, we enhance the capability of learning models to capture subtle differences and generate various input features. The Bi-LSTM model effectively captures both forward and backward dependencies in time series data, enabling accurate prediction of electrical signals. We evaluate the proposed approach using our simulated dataset and compare the proposed method to a state-of-the-art model, the Gated Recurrent Unit (GRU), demonstrating its effectiveness in improving the accuracy and reliability of induction motor signals forecasting. The finding provides valuable insights for advancing motor control and operation in industrial applications.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Retention mechanisms in HILIC have been investigated and reported in literature. However, the current understanding of the retention mechanisms is qualitative and lacks quantitative details. Previously, mechanism elucidation was based on indirect evidence, and unambiguous assignment of retention mechanisms has not been reported based on direct data. This study aims to quantitatively determine the contributions of two major retention mechanisms in HILIC, hydrophilic partitioning and surface adsorption to the overall retention of neutral compounds. Using the methodologies we developed previously, the phase ratio for adsorbed water layer and distribution coefficients were measured and used to calculate the retention factors attributed to hydrophilic partitioning. The methodology allows the determination of the contribution of surface adsorption simultaneously. The evaluation of five test compounds demonstrates that the retention may be controlled by hydrophilic partitioning, surface adsorption or both depending on compound characteristics. Quantitative assessment of retention mechanisms also makes it possible to better understand the effect of acetonitrile on retention in HILIC.

Commercially available paraffin wax LTP ST, manufactured in Poland by POLWAX, was used as a phase change material (PCM) for passive cooling of a LED panel containing 28 high power light emitting diodes (LEDs). Paraffin wax LTP ST of density = 930 kgm-3 at room temperature (RT) was chosen over other POLWAX waxes (LUXOLINA, LUXOLINA-ST, LTP 56-20) because of its melting point range (44.5 – 55.4)℃, relatively high latent heat of fusion H = 218.8 Jg-1, high specific heat Cp = 2.11 Jg-1K-1 and thermal conductivity k=0.233 Wm-1K-1 at 0 ℃ [1]. The thermophysical properties were studied in samples of pure LTP ST paraffin and doped with multi-walled carbon nanotubes (1.99, 3.49, 5.35, 10.49 wt%, MWCNT) or silver nanowires (0.26, 0.32, 1.06, 2.10, 7.35 wt%, SNW). Analysis of the thermal effects of doped samples showed a relative increase in the degree of subcooling, averaging 100% for MWCNT and 46% for SNW , a relative 15÷25% decrease in enthalpy of melting for MWCNT and 14÷16% for SNW. A 44% increase in thermal conductivity was found for the sample containing 5.35 wt% MWCNTs and a 91% increase for 1.06 wt% SNW. The results of cooling efficiency tests for 3 types of developed heat sinks made of AW-2017A aluminum alloy are presented, i.e.: (a) - full system without PCM filling, (b) - system with PCM chamber without intracellular ribs, (c) system with PCM chamber with intracellular fins.

Polymeric microparticles of polyethyleneglycol-polylactic acid-co-glycolic acid (PEG-PLGA) are widely used as drug carriers for a variety of applications due to their unique characteristics. Herein, we developed a novel method for the synthesis of uniformly sized microparticles via coaxial flow-phase separation. The study evaluated the effect of various process parameters on microparticle size and polydispersity including polymer concentration, stirring rate, surfactant concentration, and the organic/aqueous phase flow rate and volume ratio. The results demonstrated that stirring rate and polymer concentration had the most significant impact on the mean particle size and distribution whereas surfactant concentration had the most substantial impact on the morphology of particles. Several microparticle formulations yielding particle sizes in the range of (5-50 µm), morphology, and concentration were synthesized as a demonstration of the tunability and scalability of this method. Notably, by controlling the process parameters microparticles of less than ~ 7 μm could be made using polymer concentrations varying by an order of magnitude. Finally, we demonstrated the tunability and scalability of this method by showing a 10-fold increase in encapsulation efficiency, a 3-fold increase in drug loading of a model hydrophilic drug, and modified release kinetics in microparticle formulations of comparable sizes but different polymer concentrations.

in order to enhance the separation performance and to reduce the heat loss of the transmembrane for membrane distillation, the thermal efficiency and hydrophobicity of the membrane distillation should be simultaneously enhanced. In this work, a PVDF/PET hydrophobic/hydrophilic membrane is prepared by non-solvent phase inducing method. Nanosized silica aerogel (SiAG) with high porosity is added to the composite membranes. The modifying effects and operating conditions on permeate flux and thermal efficiency in direct contact membrane distillation (DCMD) are investigated. Furthermore, the latent heat of vaporization and the heat transfer across the membranes are compared for SiAG addition, which indicates that the composite PVDF@SiAG/PET membranes display a great potential for distillation-separation application with high heat efficiency.

Japanese pepper (sansho, Zanthoxylum piperitum) contains several types of sanshools belonging to N-alkylamides. Because of long-chain unsaturated fatty acids present in their structure, sanshools are prone to oxidative deterioration, which poses problems in processing. Here, we evaluated the effects of antioxidants from the genus Zanthoxylum in preventing sanshool degradation using accelerated tests. An ethanolic extract of segment membranes of the sansho fruit pericarp was incubated at 70 °C for 7 days with different antioxidants to determine the residual amount of hydroxy-α-sanshool (HαS) in the extract. α-Tocopherol (α-Toc) showed excellent HαS-stabilizing activity at low concentrations. Among phenolic acids, we noted that the HαS-stabilizing activity increased with the number of hydroxy groups per molecule. For example, gallic acid and its derivatives exhibited excellent sanshool-stabilizing activity. Quercetin was found to be a superior HαS stabilizer compared with hesperetin and naringenin. However, the effective concentration was much higher for phenolic compounds than for α-Toc. These substances are believed to play a role in preventing the decomposition of sanshools in the pericarp of sansho. These sanshool stabilizers should be useful in the development of new beverages, foods, cosmetics, and pharmaceuticals that take advantage of the taste and flavor of sansho.