Optimal planning and design of microgrids is a priority for electrification of off-grid areas. Indeed, according to one of the Sustainable Development Goals (SDG) 7, the UN recommends universal access to electricity for all but, at the lowest cost. To achieve this goal, several optimization methods with different strategies have been proposed in the literature. This paper proposes a microgrid installation and planning model based on a combination of several techniques. Python 3.10, the programming language, has been used in conjunction with machine learning techniques such as unsupervised learning based on K-means clustering and deterministic optimization methods based on mixed linear programming. These methods were complemented by the open-source spatial method for optimal electrification planning: onsset. The results obtained enabled us to simulate the model obtained, with a cluster considered as a case study, based on the elbow and k-means clustering method; then, in a second phase, to size the microgrid with a capacity of 40 kW, by optimizing all the resources available on the site: the example of the various resources in the case of Togo was considered (solar, wind, hydropower). This study therefore highlighted the optimal resources obtained by integrating battery systems by the optimization model formulated on the basis of the various technology costs, such as investment, maintenance and operating costs, based on the technical limits of the various technologies. For the optimum results obtained, solar systems account for 80% of the maximum load considered, compared with 7.5% for wind systems and 12.5% for battery systems. Next, an optimal microgrid connection model was proposed, based on the constraints of a voltage stability limit estimated at 10% of the maximum voltage drop. The substation capacity limit was also taken into account. The results obtained from the case studied enabled us again, to present selective results for load nodes in relation to the substation node. And finally, the spatial technology planning tool made it possible to obtain results on the different strategies for the various technologies required for the electrification planning study of the Togo case. The various results obtained from the different techniques provide the leads needed for a feasibility study for optimal electrification of off-grid areas, using microgrid systems.

Corneal biomechanics is a hot topic in ophthalmology. The biomechanical properties of the cornea (BMPs) have important implications in the management and diagnosis of corneal diseases such as ectasia and keratoconus. In addition, the characterization of BMPs is crucial to model the predictability of a corneal surgery intervention, the outcomes of refractive surgery or follow-up of corneal diseases. The biomechanical behavior of the cornea is governed by viscoelastic properties that allow, among other structural implications, the damping of excess of intraocular pressure and reduce damage to the optic nerve. Currently, the most versatile and complete methods to measure corneal viscoelasticity are based on air-puff corneal applanation. However, those methods lack the ability to directly measure corneal viscosity. The aim of this work is to propose a new methodology based on the analysis of corneal air-puff measurements through the Standard Linear Solid model (SLSM) to provide analytical expressions to separately calculate the elastic and time-dependent (corneal retardation time and viscosity) properties. The results shown the mean values of elasticity (E), viscosity (Ƞ) and corneal retardation time (τ) in a sample of 200 young and healthy subjects. The influence of elasticity and viscosity on viscoelasticity, high-order corneal aberrations and optical transparency is investigated. Finally, the SLSM fed back from experimental E and Ƞ values was employed to compare the creep-relaxation response between normal, an ocular hypertension patient and Ortho-K user.

This study delves into the dynamics of 'Variations' and 'Claims' within construction projects, specifically under the FIDIC-Red Book 1999 (FIDIC 1999) framework. It aims to identify, categorize, and devise mitigation strategies for key types of Variations and Claims, aligning with the FIDIC Conditions of Contract. The research, drawing on inputs from construction industry professionals including Contract Administrators and Project Managers, focuses on the MENA re-gion. This choice is driven by the region's extensive adoption of FIDIC standards and its rapidly growing construction sector. Data collection encompassed a questionnaire distributed to 80 industry experts, predominantly through interviews, focusing on countries like Saudi Arabia, UAE, Kuwait, and Egypt. These locations were chosen to reflect diverse construction practices and the involvement of international firms. Utilizing SPSS-V.25 for statistical analysis, the study uncovers the most prevalent and impactful causes of Variations and Claims, highlighting the critical need for managerial intervention. A key feature of this study is the integration of Scientometric Analysis for a quantitative review of current literature, providing a comprehensive academic context. A significant addition to the methodology is the implementation of a k-means clustering analysis. This advanced statistical technique further classifies the data into distinct clusters, each representing unique combinations of 'Frequency' and 'Impact' of Variations and Claims. The k-means analysis elucidates intricate patterns and potential solutions, offering profound insights into effectively managing these issues. These analytical advancements are crucial in identifying significant and manageable responses to reduce the frequency and impact of Variations and Claims in construction projects.

Dengue, a perilous fever-type illness transmitted by mosquitoes, remains a significant global health concern. The incidence of dengue outbreaks is primarily influenced by climate factors, contributing to fluctuating dengue cases. Therefore, this study aims to develop predictive models for dengue outbreaks employing Machine Learning (ML) techniques. Four distinct ML models, namely K-Nearest Neighbor (KNN), Random Forest (RF), Gradient Boosting Regressor (GBR), and Support Vector Regressor (SVR), were employed in this study. Prior to model analysis, thorough data preprocessing was conducted. In some instances, certain attributes exhibiting sparse correlations with dengue occurrence were eliminated based on correlation analysis. Upon finalizing the models, performance evaluation was executed through comparison based on Mean Absolute Error (MAE) metrics. The findings of this comparative analysis revealed that the KNN model exhibited significantly superior performance compared to the other three models. This outcome underscores the potential of KNN in enhancing the accuracy of dengue outbreak predictions.

Fraudulent transactions pose a significant threat to financial institutions and e-commerce platforms.Machine learning models, trained on historical labeled data (fraudulent vs. legitimate transactions), are often employed to identify and prevent fraud. However, real-world datasets frequently exhibit class imbalance, where fraudulent transactions (minority class) are significantly outnumbered by legitimate transactions (majority class). Machine learning models may perform poorly as a result of this imbalance, underestimating fraud and favouring the majority class. This paper proposes a novel approach to address class imbalance and improve fraud detection accuracy. We explore the implementation of FROST (Feature space RObust Synthetic saTuration) oversampling, a technique specifically designed to generate synthetic samples for the minority class. The FROST function leverages the k-nearest neighbors (KNN) algorithm and a user-defined amplification factor (m) to create synthetic data points that closely resemble existing minority class instances. We integrate the FROST-enhanced oversampling technique into the machine learning pipeline for fraud detection. The paper evaluates the effectiveness of this approach compared to traditional oversampling methods and analyzes its impact on classification accuracy metrics.

Build a special identical equation, use its calculation characters to prove and search for solution of any odd converging to 1 equation through (*3+1)/2^k operation, change the operation to (*3+2^m-1)/2^k, and get a solution for this equation, give a specific example to verify. Thus prove the Collatz Conjecture is true. Furthermore, analysis the sequences produced by iteration calculation during the procedure of searching for solution, build a weight function model, prove it decrease progressively to 0, build a complement weight function model, prove it increase to its convergence state. Build a (*3+2^m-1)/2^k odd tree, prove if odd in (*3+2^m-1)/2^k long huge odd sequence can not converge, the sequence must outstep the boundary of the tree after infinite steps of (*3+2^m-1)/2^k operation.

In the history of high-performance polymer composite parts with continuous in-plane fibre reinforcement, the comparatively moderate structural-mechanical properties in their out-of- plane-z-direction and the limited load carrying capability between individual reinforcement layers within the laminated structures have always been one of the greatest challenges. Plenty of research work has been carried out to improve load transfer capability as well as fracture toughness for crack opening events between the reinforcement layers by means of out-of-plane fibre reinforcement implementation, for example by sewing or z-pinning technologies. However, the results have not become established across a wide range of applications so far, because the technologies used have led to considerable losses of in-plane strength properties. In this paper first results are presented for a new method of a low fraction z-fibre reinforcement by means of very thin diameter laser drilled holes filled with short carbon fibres, demonstrating potential to improve Mode II fracture toughness.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

In Indonesia, types of meat are still identified manually due to increasing prices for beef and buf-falo ahead of Idul Fitri. Traders mix beef with pork to thwart the beef scam. Haar wavelet and GLCM, GLCM with angles of 0°, 45°, 90°, and 135°, as well as matrices using contrast, correlation, energy, homogeneity, and entropy, are used in feature extraction. The following are the results of meat image classification testing using k-NN, Haar wavelet, and GLCM: The k-NN algorithm shows superiority in identifying fresh (99%), frozen (99%), and rotten (96%) meat texture images with the most fantastic accuracy results in every situation. Meanwhile, GLCM routinely provides good results, especially regarding the texture image of fresh meat (183.21) and rotten meat (115.79). However, despite delivering less throughput than k-NN and GLCM, Haar wavelets are still helpful, especially when dealing with fresh meat texture images (89,96).

Understanding the optimal strategy for a real estate investment and how performance changes based on characteristics is crucial for optimising the achievable return. This is prominent in tourist areas such as Paphos where there is no clear distinction as to whether short or long-term approaches are optimal. The study aimed to develop a model for predicting the optimal rental strategy whilst assessing which model performed best and which property attributes impacted its return the greatest. Short-term data was collected from AirDNA and long-term data was manually collected from real estate agents websites. Furthermore, Random Forest, K-Nearest Neighbour and Multiple Linear Regression models were created to predict the highest and best use for each property. Model accuracy varied between data sets with the best performing model for short-term properties being Random Forest (R-Squared: 0.843), and Distance-Based Multiple Linear Regression for long-term approach (R-Squared: 0.843). The study demonstrated that accurate models could be created to predict the optimal rental strategy with the number of bedrooms being the main driver for rental income, followed by luxury finishes and the presence of a pool. It found that locational characteristics didn’t impact the returns significantly assuming that the property was located within a tourist area.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

In this project the EEG – electroencephalogram - channel(s) will be characterized to diagnose PTSD – Post-traumatic stress disorder – cases. For this aim, we applied boosting methods including a combination of K-mean and Support Vector Machine (SVM) models to find the feature weights to detect the PTSD cases. We classified 32 channels of 12 subjects including 6 PTSD and 6 healthy controls using a 6-mean classifier. The linear SVM found the weights of distinguished channels within each subject for each cluster. It was found that the significant SVM weights of F4, F8, and Pz are smaller in PTSD than in healthy subjects. This new method can be used as a tool to better understand the interaction of EEG signals and diagnosis.

The design of a mixed-mode proportional-integral-derivative (PID) controller circuit using current-feedback operational amplifiers (CFOAs) as active components is proposed. With the same circuit topology, the proposed configuration of three CFOAs, four resistors, and two capacitors is capable of performing the PID controller in all four operation modes: namely voltage mode, trans-admittance mode, current mode, and trans-impedance mode. Numerous mathematical analyses are conducted to determine the controller performance under ideal and non-ideal conditions. Additionally, the mixed-mode second-order lowpass filter is suggested, and also used to examine the workability of the proposed mixed-mode PID controller in a feedback control structure. The proposed PID controller is implemented with the commercially available IC-type CFOA AD844, and the simulation results are presented to illustrate the functionality of the controller and its closed-loop control system.

Several efforts have been made to estimate the prevalence of different types of antibiotic resistance in different regions of Nigeria. The study investigated the prevalence of Klebsiella pneumoniae encoding genes for CTX-M, TEM, and SHV-1 extended-spectrum beta-lactamases (ESBL) enzymes isolated from urine samples of non-hospitalized patients with suspected UTI in Lagos State, Nigeria. A 4-month retrospective study, spanning from May 2023 to August 2023, was conducted. K. pneumoniae was isolated from urine samples using standard microbiological methods. The modified Kirby-Bauer disc diffusion method was used to test for antibiotic susceptibility, and Clinical and Laboratory Standard Institute (CLSI) guidelines were followed for interpretation. The double-disk synergy method was used to confirm the phenotypic identity of ESBL producers, and the results were interpreted in accordance with CLSI guidelines. The phenotypic method was utilized for ESBL screening, employing the standard disk diffusion method. The CTX-M ESBL gene, TEM gene, and SHV gene were found using multiplex PCR. Results revealed that 41 K. pneumoniae isolates were resistant to third-generation Cephalosporins; the isolates showed resistance to ceftazidime in 100% of cases and ceftriaxone in 80.49% of cases respectively. It was determined that 8 (19.51%) of the isolates produced ESBL. Among Klebsiella isolates, the frequencies of the SHV, TEM, and CTX-M genes were 31 (75.61%), 4 (9.76%), and 10 (24.39%), in that order. Four isolates (9.67%) had the SHV, TEM, and CTX-M genes, while eight (19.51%) of the isolates possessed both the SHV and CTX-M genes. This investigation demonstrates high frequency, wide range of patterns and coexistence of ESBL genes in K. pneumoniae isolates from outpatient UTI patients. Although several phenotypic tests have been used for ESBL detection, testing directly for the presence of ESBL genes is always more accurate. The majority of the isolates of Klebsiella pneumoniae ESBL producers had the SHV gene identified.

Abstracts In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

The ANSYS 2024R1 student edition was used to create a finite element model of a basketball rim and backboard. This finite element model included the use of steel for the rim and its mount, a tempered glass backboard, and an aluminum frame behind the backboard. After a mesh was created, fixed support boundary conditions were applied to the four corners of the aluminum frame. The subsequently calculated mode shapes and frequencies were compared to empirical modal analysis previously done at the United States Military Academy at West Point, New York. Four mode shapes and frequencies agreed rather well between the theoretical finite element analysis and previously published empirical modal analysis, specifically where the rim was vibrating in the vertical direction, which was the direction that the accelerometer was aligned for modal analysis. However, three mode shapes missed by the empirical modal analysis were found where the vibration of the rim was confined to the horizontal plane, which was orthogonal to the orientation of our accelerometer.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Predictions of mean values of statistical variables of large scale turbulent flow by the widely used basic k-ϵ model and a new fundamentally based model are verified against published results of Direct Numerical Simulations DNS of the Navier-Stokes equations. The verification concerns turbulent channel flow at shear Reynolds numbers of 950, 2000 and 104. The basic k-ϵ model is largely based on empirical formulations accompanied by calibration constants. This contrasts with the new model where descriptions of leading statistical quantities are based on the general principles of statistical turbulence at large Reynolds number. Predicted values of major output variables such as turbulent viscosity, diffusivity of passive admixture, temperature, and fluid velocities compare well with DNS in case of the new model. Significant differences are seen in case of the basic k-ϵ model.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

With the increasing of China's international status and the acceleration of the process of global economic integration, the internationalization strategy of Chinese enterprises is getting deeper and deeper. This paper analyzes the problems and challenges faced by the international supply chain management of Chinese bamboo weaving and creative products, and puts forward a set of supply chain management model that ADAPTS to the international development. Firstly, the concept, connotation and types of supply chain management are sorted out through literature review. Secondly, this paper analyzes the current situation of international supply chain management of bamboo editing and creative products, and points out the existing problems. Thirdly, based on the theory and practice of international supply chain management, this paper puts forward a set of supply chain management model suitable for the international development of bamboo editing and creative products. Finally, taking a bamboo weaving and creative products enterprise as an example, the application effect of the supply chain management model is empirically analyzed. The results show that the supply chain management model can effectively reduce the cost and improve the efficiency, and is conducive to the international development of bamboo editing and creative products.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

E-scooters are a micromobility transportation option for completing short trips. In recent years, many ‎cities welcomed shared e-scooters in an effort to offer more mode choices, increase travelers' ‎convenience, and reduce automobile use in their service areas. However, a knowledge gap still remains ‎regarding the acceptability of shared e-scooters as a transportation option, which motivates additional ‎research on user and non-user preferences and attitudes toward e-scooter use. This study investigates ‎latent variables impacting the adoption of shared e-scooters in urban areas, focusing on mode choice ‎factors and attitudes towards e-scooter use and car use. The study utilizes machine learning (ML) ‎techniques and SHAP analysis to analyze survey data (N=1196) collected from travelers in Washington, ‎D.C., Miami, FL, and Los Angeles, CA, in 2021 and 2022. A comparative analysis is performed to develop ‎comprehensive demographic profiles of e-scooter users. The analysis reveals gender (male), age (25-39 ‎years age group), higher income, and educational background as the most relevant factors toward e-‎scooter use. Attitudinal variations among e-scooter users and non-users underscore the complexity of ‎perceptions toward e-scooter use, with significant differences in mode choice factors and attitudes ‎toward the use of e-scooters and private vehicles. Notably, educational background ranked as a significant ‎factor in Washington, D.C., and Miami, while Factor 3, derived from factor analysis and encompassing car ‎use attitudes and the utilization of technology, emerged as influential in Los Angeles. This research ‎contributes fresh insights into factors shaping e-scooter adoption, offering a foundation for informed ‎urban transportation planning and policymaking. The holistic approach showcased in this study enhances ‎understanding of shared micromobility and its implications for urban mobility.

The antimicrobial quantitative structure–activity relationship of plant flavonoids against Gram-positive bacteria was established in our previous works, and the cell membrane was confirmed as a major site of action. To investigate whether plant flavonoids have similar antibacterial effects and mechanisms against both Gram-negative and Gram-positive bacteria, here, the minimum inhibitory concentrations (MICs) of 37 plant flavonoids against Escherichia coli were determined using the microdilution broth method, and then the correlation between their lipophilic parameter ACD/LogP or LogD_7.40 value and their MIC was analyzed. Simultaneously, the correlation between the ACD/LogP or LogD_7.40 value and the MIC of 46 plant flavonoids reported in literature against E. coli was also analyzed. Both sets of results showed that there is a significant correlation between the LogP value and the MIC of plant flavonoids against Gram-negative bacteria. However, it is difficult to effectively predict the MIC of plant flavonoids against Gram-negative bacteria from their lipophilic parameters. By comparing two regression curves derived from plant flavonoids against Gram-negative and Gram-positive bacteria, it was further discovered that the antibacterial activities of most plant flavonoids against Gram-negative bacteria are stronger than those against Gram-positive bacteria when their LogP values are less than about 3.0, but the opposite is true when their LogP values are more than about 3.6. Moreover, this comparison also suggests that unlike mainly acting on the cell membrane of Gram-positive bacteria, plant flavonoids have multiple mechanisms against Gram-negative species, while the cell membrane is also an important action site among them. Combined with the correlation analyses between the enzyme inhibitory activity and the LogP value of the reported flavonoids, it was further suggested that DNA gyrase is another important target of plant flavonoids against Gram-negative bacteria.

In this paper, a low-power Injection-Locked Clock and Data Recovery (ILCDR) using 28nm FDSOI technology is presented. The back-gate auto-biasing of UTBB-FDSOI transistors allows us to create a QRO (Quadrature Ring Oscillator) reducing both size and power consumption. By injecting a digital signal into this circuit, we realize an Injection-Locked Oscillator (ILO) with low jitter. Thanks to the good performance of this oscillator, we propose a low power ILCDR with fast locking time and low jitter for burst-mode applications. The main novelty consists in the implementation of a complementary QRO based on back-gate control using FDSOI technology to realize a simple and efficient ILCDR circuit. With a Pseudo-Random Binary Sequence (PRBS7) at 868Mbps, the recovered clock jitter is 26.7ps (2.3%UIp-p) and the recovered data jitter is 11.9ps (1%UIp-p). With a 0.6V power supply, the power consumption is 318μW. The estimated Chip area is around 6600μm².

Recognition, decoding and tracking of vortex patterns is of increasing importance in many fields reaching from astronomical observation of distant galaxies to turbulence phenomena in liquids or gases. Currently, coherent light beams with orbital angular momentum (OAM) are of particular interest for optical communication, metrology, micro-machining or particle manipulation. One common task is to identify characteristic spiral patterns in pixelated intensity maps at real-world signal-to-noise ratios. Recently, Fast Fourier Transform (FFT) was applied to the quantitative analysis of spiral interference patterns of OAM beams. Our study considers this approach in more detail. It is demonstrated that specific information can be extracted by combining conformal mapping by polar transform with determining one- or two-dimensional angular frequency spectra either in spatially fixed or scanning mode. Results of proof-of-principle experiments are presented.

This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

This paper provides a new discovery that adds to the contemporary theory of modelling of non-stationary queues, by capturing analytically the behavior of the root parameter, for the G1/M/1 PSFFA model of non-stationary Ek/M/1 queue. Additionally, it has been also revealed that the resulting root parameter reduces to the PSFFA model of non-stationary queue. Potential applications of PSFFA to Computer engineering are provided. Some challenging open problems are addressed combined with closing remarks and future research directions.

The significance of Kashmir conflict as one of the world’s longest running conflicts has frequently drawn the attention of both communication and international relations’ scholars which makes it an important issue from the perspective of interdisciplinary approach. The researchers have attempted to assemble a brief history of the Indian held Jammu and Kashmir Conflict from the time of partition in 1947 to the developments which took place till 2019 in the light of the available literature. The paper provides substantial historical context of the important events like instrument of accession, UN resolutions on Kashmir conflict, Simla Accord, Gawkadal Massacre , Lahore Declaration, Kargil War, killing of Burhan Wani, Uri attack and Article 370’s abrogation .

Mangrove plant seedling cultivation is crucial for the protection, management and restoration of mangrove ecosystem. In this study, we focused on Kandelia obovata, a typical mangrove, and evaluated nursery cultivation with different combinations of three salinity levels (S1: 0 ppt, S2: 10 ppt, and S3: 20 ppt), three genealogies (EZD, JX, and YZ), and five growth media (M1: 100% loess, M2: 100% sandy, M3: 50% loess + 50% sandy, M4: 40% loess + 40% sandy + 20% peat, and M5: 40% loess + 40% sandy + 20% coir), by measuring the growth parameters such as mortality rate, seedling height, diameter, and biomass partition. These growth indexes were significantly affected by salinity and medium, and genealogies also had significant effects on mortality rate and biomass accumulation. S2 or S3 both had lower mortality and higher growth indexes than S1. M1 was the medium that increased seedlings height, diameter and biomass the most and had the lowest death rate. EZD and JX were also higher levels than YZ in these indicators, but the difference between them was not obvious. S3, M1, and EZD consistently performed well in fuzzy evaluation and quality assessment. Furthermore, combinations involving these treatments also produced highly favorable results. These results furnish both a theoretical and practical foundation for advancing nursery cultivation techniques and germplasm breeding of K. obovata in mangroves.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

This study investigates the application of regression neural networks, in particular the fitrnet model, in predicting the hardness of steels. The experiments involve extensive tuning of hyperparameters using Bayesian optimization and employ 5-fold and 10-fold cross-validation schemes. The trained models are rigorously evaluated, and their performances are compared using various metrics such as mean square error (MSE), root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). The results provide valuable insights into the effectiveness of the models and their ability to generalize to unseen data. In particular, Model 4208 (8-85-141-1) emerges as the top performer with an impressive RMSE of 1.0790 and an R² of 0.9900. The research paper contains an illustrative example that demonstrates the practical application of the developed model in determining the hardenability band for a specific steel grade and shows the effectiveness of the model in predicting and optimizing heat treatment results.

Rare ginsenoside compound K (CK), is an intestinal microbial metabolite with a low natural abundance that is primarily produced by physicochemical processing, side chain modification, or metabolic transformation in the gut. Moreover, CK exhibits potent biological activity compared to primary ginsenosides, which has raised concerns in the field of ginseng research and development as well as ginsenosides-related dietary supplements and natural products. Ginsenosides Rb1, Rb2, and Rc are generally used as a substrate to generate CK via several bio-conversion processes. Current research shows that CK has a wide range of pharmacological actions including boosting osteogenesis, lipid and glucose metabolism, lipid oxidation, insulin resistance, anti-inflammatory, and anti-apoptosis properties. Further research on the bioavailability and toxicology of CK can advance its medicinal application. The purpose of this review is to lay the groundwork for future clinical studies and the development of CK as a therapy for metabolic disorders. Furthermore, the toxicology and pharmacology of CK are investigated as well in this review. The findings indicate that CK primarily modulates signal-ing pathways associated with AMPK, SIRT1, PPARs, WNTs, and NF-kB. It also demonstrates a positive therapeutic effect of CK on nonalcoholic fatty liver disease, obesity, hyperlipidemia, diabetes, and its complications, as well as osteoporosis. Additionally, the analogues of CK showed more bioavailability, less toxicity, and more efficacy against disease states. Enhancing bioavailability and regulating hazardous variables are crucial for its use in clinical trials.

Background and objective K. pneumoniae appeared to be a significant problem due to its ability to accumulate antibiotic-resistance genes. After 2013, alarming colistin resistance rates among carbapenem-resistant K. pneumoniae have been reported in the Balkans. The study aims to perform an epidemiological, clinical, and genetic analysis of a local outbreak of COLr CR-Kp. Material and methods All carbapenem-resistant and colistin-resistant K. pneumoniae isolates observed among patients in the ICU unit of Military Medical Academy, Sofia from 1 January to 31 October 2023 were included. The results were analyzed according to the EUCAST criteria. All isolates were screened for blaVIM, blaIMP, blaKPC, blaNDM, and blaOXA-48. Genetic similarity was determined using the Dice coefficient as a similarity measure and the unweighted pair group method with arithmetic mean (UPGMA). mgrB genes and plasmid-mediated colistin resistance determinants (mcr-1, mcr-2, mcr-3, mcr-4, mcr-5) were investigated. Results There was a total of 379 MDR-K. pneumoniae isolates, 88% of which were carbapenem-resistant. Of them, there were 9 (2.7%) colistin-resistant isolates in six patients. A time and space cluster for five patients was found. Epidemiology typing showed that two isolates belonged to clone A (pts. 1, 5) and the rest to clone B (pts. 2-4) with 69% similarity. Clone A were coproducers of blaNDM-like and blaOXA-48-like and had mgrB-mediated colistin resistance (40%). Clone B isolates had only blaOXA-48-like and intact mgrB genes. All isolates were negative for mcr-1,-2,-3,-4,-5 genes. Conclusions The study describes a within-hospital spread of two clones of COLr CR-Kp with a 60% mortality rate. Clone A were coproducers of NDM-1 and OXA-48-like enzymes and had mgrB-mediated colistin resistance. Clone B isolates had only OXA-48-like enzymes and intact mgrB genes. No plasmid-mediated was found. The extremely high mortality rate and limited treatment options warrant strict measures to prevent outbreaks.

Abstract：The brain often switches freely between focused attention and divergent thinking, and the default mode network (DMN) is activated during brain rest. The discovery, function and characteristics of default mode network all indicate that learning does not stop when the brain "rests". Mental disease can lead to dysfunctional default mode networks, which affects learning adversely. Therefore, default mode network plays an important role in learning. Neural activities such as β-wave rhythm regulation, "subconscious" divergence mode initiation, hippocampal function and neural replay occur during default mode, which also explain that "rest" promotes learning. This paper reveals the role and neural mechanism of default mode network in learning from the neural level, discusses the essential role default mode network plays in learning, and default mode network enables rest to promote learning.

The electrical energy supply relies on the satisfactory operation of insulators. The ultrasound recorded from insulators in different conditions has a time series output, which can be used to classify faulty insulators. The random convolutional kernel transform (Rocket) algorithms use convolutional filters to extract various features from time series data. This paper proposes the combination of Rocket algorithms, machine learning classifiers, and empirical mode decomposition (EMD) methods, such as complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN), empirical wavelet transform (EWT), and variational mode decomposition (VMD). The results show that the EMD methods combined with MiniRocket, significantly improve the accuracy of logistic regression in insulator fault diagnosis. The proposed strategy achieves respectively an accuracy of 0.992 using CEEMDAN, 0.995 with EWT, and 0.980 with VMD. These results highlight the potential of incorporating EMD methods in insulator failure detection models to enhance the safety and dependability of power systems.

This study aimed to determine the correlation of colour M-mode velocity propagation in the assessment of left ventricular diastolic function among acute decompensated heart failure patients with preserved ejection fraction (HFpEF). This research is an observational analytical study using a cross–sectional study design conducted from April to June 2022. The subjects of this study were patients diagnosed with acute HFpEF and treated at Dr. Soetomo General Academic Hospital, Surabaya. Patients with heart rhythm disturbances, moderate to severe valvular heart disease, and congenital heart defects were excluded from this study. Patients were measured for diastolic function including mitral valve early mitral inflow velocity (MV E Velocity), mitral peak velocity of early filling (E’) (E' Septal and E' Lateral), left atrial volume index (LAVI), The maximal tricuspid regurgitation velocity (TR V Max), Vp, the ratio of early diastolic mitral inflow velocity to early diastolic mitral annulus velocity (E/E'), the ratio between early and late ventricular filling velocity (E/A) and E/Vp Ratio. N-terminal-pro hormone B-type natriuretic peptide (NT–ProBNP) examination was also performed on study subjects as an additional diagnosis of acute heart failure. There were 33 patients who met the inclusion and exclusion criteria and were included in our study. There were 26 patients (78.8%) with grade I diastolic dysfunction, 4 patients (12.1%) with grade II diastolic dysfunction, and 3 patients (9.1%) with grade III diastolic dysfunction. There is a strong positive correlation between Vp with parameters E' Septal (p = < 0.001; r = 0.636) and E' Lateral (p = < 0.001; r = 0.650). Vp is negatively correlated with the ratio E/E' (p = 0.029; r = –0.37). The PCWP estimate with E/Vp ratio had a strong correlation with the NT–Pro BNP value > 300 pg/ml in acute HFpEF patients (p = < 0.001; r = 0.726) compared to the PCWP estimate with E/E' (p = < 0.001; r = 0.549). There is no correlation between Vp value and degree of diastolic dysfunction in patients with acute HFpEF.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.

A novel reinforcement learning deep deterministic policy gradient agent-based sliding mode control (DDPG-SMC) approach is proposed to suppress the chattering phenomenon in the attitude control for quadrotors, in the presence of external disturbances. First, the attitude dynamics model of the studied quadrotor is derived and the attitude control problem is described by formulas. Second, a sliding mode controller including its sliding mode surface and reaching law is selected for the nonlinear dynamic system, and the stability of the designed SMC system is supported by Lyapunov stability theorem. Third, a reinforcement learning (RL) agent based on deep deterministic policy gradient (DDPG) is trained to adjust the switching control gain adaptively. During the training process, the input signals of agent are the actual and desired attitude angles, and the output action is the time-varying control gain. Finally, the above trained agent is applied to the SMC as a parameter regulator, to implement the adaptive adjustment of the switching control gain related to reaching law, and the simulation results verify the robustness and effectiveness of the proposed DDPG-SMC method.

We use COMSOL Multiphysics software to model optical processes in media and the effects of light propagation in whispering gallery mode resonators (WGMRs). Although plane wave irradiating on resonator does not create resonances, it was shown that they can be obtained when focused tangentially on the perimeter of the resonator. We demonstrate that resonances can be excited in resonators by prism coupling when the incident angle of the light is larger than the angle of total internal reflection. We determined the optimal distance between the prism and the resonator to get the strongest resonances. Bio-sensing principle of WGMRs is shown by demonstrating that the shift of resonances increases with a larger number of "bio-molecules" attached to the surface of WGMR. Surface functionalization and surface roughness were explored.

The utilization of smart IoT devices, commonly referred to as digital twins, is aimed at the digitalization of human knowledge within aquaculture processes. This involves the incorporation of cutting-edge technologies, including information-based management with big data and modeling, to automate machinery and gain comprehensive insights into the aquaculture environment and fish farm conditions. The ultimate objective is to empower farmers to make informed decisions, furnishing them with objective data to enhance their capacity in monitoring and controlling the various factors impacting fish production. As a result, farming decisions can be fine-tuned to enhance fish health and optimize farm output. In the context of large and modern aquaculture farms, technological innovation becomes imperative to automate processes, minimize labor requirements, and streamline fish feeding operations. Remarkably, the literature currently offers limited discussions on the digital transformation of aquaculture through the application of digital twin methodologies. A prior study underscores the critical influence of factors such as market prices and fish survival rates on the profitability of offshore caging culture. In this study, we embark on an analysis of the prerequisites for establishing a digital twin infrastructure tailored to intelligent fish feeding management. This infrastructure is designed to facilitate the integration of technology and data-driven decision-making, ultimately enhancing the efficiency of fish feeding processes. The proposed architecture for the fish feeding digital twin encompasses various digital twin components, encompassing water quality forecasting, fish population assessment, fish metrics estimation, fish feed prediction, and evaluation of fish feeding intensity. Furthermore, we optimize the daily fish feeding process through reinforcement learning algorithms. Finally, we implement a cloud-based AIoT system that provides the runtime environment for executing digital twins and controlling our intelligent fish feeding machinery. Experimental findings underscore the efficacy of the proposed digital twin system in significantly improving traditional fish feeding processes, notably in terms of reducing food costs and labor requirements.

Malaria, leishmaniasis, and African trypanosomiasis are protozoan diseases that constitute a major global health problem, especially in developing countries; however the development of drug resistance coupled with the toxicity of current treatments have hindered their management. The implication of certain enzymes (dihydrofolate reductase, DHFR) or proteins (potassium channels) in the pathogenesis of these protozoan diseases is undeniable. In this study, a series of three DHFR inhibitors (6-5 fused heterocyclic derivatives X, Y and Z) and one K+ channel blocker (E4031) were screened for their inhibitory effect on Leishmania donovani, Plasmodium falciparum, and Trypanosoma brucei. Resazurin assay was used to assess antitrypanosomal and antileishmanial activities of test compounds, whereas the antimalarial activity was appraised through SYBR Green I test. Moreover, cytotoxicity of test compounds was evaluated on Vero, Raw 264.7 and HepG-2 cells using the resazurin-based test, whilst their pharmacokinetic properties were predicted using the online tool pkCSM. As a result, compound Y revealed a selective (selectivity index range: 2.69 - >61.4; Vero, Raw 264.7 and HepG-2 cells) and broad-spectrum antiprotozoal activity against L. donovani promastigotes (IC50: 12.4 µM) and amastigotes (IC50: 4.28 µM), P. falciparum (IC50: 0.028 µM), and T. brucei brucei (IC50: 0.81 µM). In addition, compound X inhibited the growth P. falciparum (IC50: 0.0052 µM) and T. brucei brucei (IC50: 6.49 µM). In silico screening of the active antiprotozoal compounds revealed positive drug-likeness scores as none of Lipinski's rule of five’s criteria was violated by these compounds. However, in-depth pharmacokinetic and mechanistic studies are warranted to support discovery of novel antiprotozoal agents against malaria, leishmaniasis, and African trypanosomiasis by repurposing K+ channel blocker and DHFR inhibitors.

When overhead lines are impacted by lightning, the traveling wave of the fault contains a wealth of fault information. The accurate extraction of feature quantities from transient components and their classification is fundamental to the identification of lightning faults. The extraction process may involve modal aliasing, optimal wavelet base issues, and inconsistencies between the lightning strike distance and the fault point, which have the potential to impact the effectiveness of recognition. This paper presents a method for identifying lightning strike faults by utilizing Kullback-Leibler (KL) divergence enhanced Variational Mode Decomposition (VMD) and Symmetric Geometry Mode Decomposition (SGMD) improved with Permutation Entropy (PE) to address the aforementioned issues. A model of a 220 kV overhead line is constructed using real faults to replicate scenarios of winding strike, counterstrike, and short-circuit. The three-phase voltage is chosen and then sub-jected to Karenbaren decoupling in order to transform it into zero mode, line mode 1, and line mode 2. The zero mode voltage is decomposed using KL-VMD and PE-SGMD methods, and lightning identification criteria are developed based on various transient energy ratios. The research findings demonstrate that the criteria effectively differentiate between winding strike, counterstrike, and short-circuit faults, thus confirming the accuracy and efficacy of the lightning fault identification criteria utilizing KL-VMD and PE-SGMD.

Spectral image analysis has the potential to replace traditional approaches for assessing plant responses to different types of stress including herbicide, through non-destructive and high-throughput screening (HTS). Therefore, this study was conducted to develop a rapid bioassay method using a multi-well plate and spectral image analysis for diagnosis of herbicide activity and mode of action. Crabgrass (Digitaria ciliaris) as a model weed was cultivated in multi-well plates and subsequently treated with 6 herbicides with different modes of action when they reached the 1-leaf stage, using only a quarter of the recommended dose. To detect plant response to herbicides, plant spectral images were acquired after herbicide treatment using RGB, infrared (IR) thermal, and chlorophyll fluorescence (CF) sensors and analyzed for diagnosing herbicide efficacy and mode of action. Principal Component Analysis (PCA) using all spectral data successfully distinguished herbicides and clustered depending on their modes of action. The performed experiments have shown that the multi-well plate assay combined with spectral image analysis can be successfully applied for herbicide bioassay. In addition, the use of spectral image sensors, especially in CF image, would facilitate HTS by enabling rapid observation of herbicide response, as early as 3 hours after herbicide treatment.

To address the trajectory tracking issue for quadrotors working under the influence of external disturbances, a control scheme is designed for position and attitude trajectory tracking. Firstly, the quadrotor dynamic model is derived for control design. Secondly, adaptive integral backstepping control (AIBS) is employed in the position loop in which adaptive estimation is used to estimate the upper bounds of disturbances. Subsequently, a new adaptive backstepping fast nonsingular integral terminal sliding mode control (ABFNITSM) is proposed to follow desired Euler angles. The intro-duction of fast nonsingular terminal sliding mode and integral element is to realize fast convergence and accurate tracking. Dead zone technique is applied to minimize estimation errors. Besides, a saturation function is utilized to eliminate chattering phenomenon. Finally, simulation experiments are conducted under the Simulink environment. The proposed control is verified by comparing it with traditional integral terminal sliding mode control (ITSM) and integral backstepping control (IBS).

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

Recently, Shehata et al. [37] introduced the r+1Rs(B;C; z) matrix function and established some properties. The aim of this study established to devote and derive certain basic properties including analytic properties, recurrence matrix relations, dierential properties, new integral representations, k- Beta transform, Laplace transform, fractional k-Fourier transform, fractional integral properties, the k-Riemann{Liouville and k-Weyl fractional integral and derivative operators an extended version of r+1Rs;k matrix function. We establish its relationships with other well known special matrix functions which have some particular cases in the context of three parametric Mittag-Leer matrix function, k- Konhauser and k-Laguerre matrix polynomials. Finally, some special cases of the established formulas are also discussed.

As most of the current dynamic positioning systems are based on model ships, they cannot accu-rately reflect the motion state, position changes, and mutual influence of each part of the dynamic positioning system of actual ships in complex environments. Other actual ships such as cargo ships cannot add various sensors and auxiliary equipment to verify and analyze the positioning system. This article takes the intelligent research and training dual-use ship of Dalian Maritime University, which integrates scientific research and training, as the object of study. This ship will not be affected by the voyage period and route and can choose a suitable sea area for research. Therefore, in order to improve the accuracy and reliability of the dynamic positioning system, research on the ship’s dynamic positioning system was carried out. Firstly, an accurate mathematical model of ship motion was established, and the hydrodynamic derivatives of ship model motion were obtained by nu-merical calculation, and applied to the three-degree-of-freedom model of the intelligent research and training dual-use ship. Then, the model was used as part of the closed-loop simulation model of the ship’s dynamic positioning system, and the terminal sliding mode controller was used for sim-ulation and emulation, thereby obtaining ideal simulation test results. This research helps to im-prove the accuracy and reliability of the dynamic positioning system and provides new ideas and methods for ship motion control.

Slave Province in Canada is an Archean granite-supracrustal terrane at the northwestern corner of the Canadian Shield. It is bordered by the Thelon–Taltson orogen (2.0 to 1.9 Ga) to the south-east and the Wopmay orogen (1.9 to 1.8 Ga) to the west. Acasta gneisses exposed in the western-most Slave province and the Wopmay rocks close to the gneisses were collected systematically for K-Ar and laser step-heating 40Ar /39Ar analyses of the biotite and amphibole. The K-Ar biotite ag-es of the four Wopmay samples range from 1816 ± 18 Ma to 1854 ± 26 Ma, which is within the reported U-Pb zircon age range of the Wopmay orogen. The K-Ar biotite ages of the fifteen Acasta gneisses range from 1779 ± 25 Ma to 1877 ± 26 Ma, except for a younger sample (1711 ± 25 Ma). The 40Ar/39Ar biotite analyses of the three samples from the Wopmay orogen give the plateau ages of 1826 ± 21 Ma, 1886 ± 13 Ma, and 1870 ± 18 Ma. On the other hand, the 40Ar/39Ar analyses of the biotite crystals from the Acasta gneiss show a variety of ages. Three samples show the plateau ages of 1877 ± 8 Ma, 1935 ± 14 Ma, and 1951 ± 11 Ma. These plateau ages are a little older than the total gas ages. The 40Ar/39Ar analyses of the amphibole crystals show more varied age rela-tions. The two samples show consistent age relations between the plateau ages (1814 ± 22 Ma and 1964 ± 12 Ma) and the total gas ages (1789 ± 23 Ma and 1967 ± 11 Ma), respectively. Some sam-ples have the apparent old age of 2000 Ma in the middle temperature fractions. These old frac-tions are due to that the originally existed amphibole crystals formed in Archean were affected by the thermal events during the Wopmay orogeny. but did not fully reset. The results suggest that the K-Ar system ages of the biotite and amphibole of the Archean Acasta gneiss that is aged from 4200 to 2600 Ma of zircon U-Pb ages were rejuvenated in the Paleo–Proterozoic ages. The heat source that rejuvenated the K-Ar system ages may have arisen due to the asthenospheric intrusion into the wedge mantle, which took place because of the subduction rollback.

Klebsiella pneumoniae complex is one of the most commonly isolated bacteria within human infections. These microorganisms are opportunistic pathogens that pose a serious threat to public health due to possibility of transmission in the human population. Resistance to carbapenems is one of the most important antimicrobials resistance mechanisms amongst them. In this situation therapeutic options are limited. Therefore, the aim of this study was to evaluate fosfomycin, colistin, ceftazidime-avibactam and meropenem-vaborbactam in vitro activity against multidrug-resistant K. pneumoniae complex strains. The study involved 160 strains of Gram-negative rods: K. pneumoniae – 138 and K. variicola - 22. Minimal inhibitory concentration of fosfomycin was estimated by agar dilution method and for colistin by microdilution method. The susceptibility to ceftazidime-avibactam and meropenem-vaborbactam was determined by gradient strip method. All of the analysed K. pneumoniae complex isolates produced extended-spectrum beta-lactamases and 60.0% carbapenemases. The most of the analysed strains were susceptible to fosfomycin and colistin (62.5%). Among pandrug-resistant K. pneumoniae complex isolates the most were susceptible to colistin (43.9%). Fosfomycin has good activity against ESBL- and VIM-positive isolates from this complex. In turn, colistin has satisfactory in vitro activity against KPC- and VIM-positive isolates from K. pneumoniae complex. Ceftazidime-avibactam has good activity against K. pneumoniae complex strains producing ESBL, KPC and OXA enzymes. In turn, meropenem-vaborbactam has satisfactory in vitro activity against ESBL- and KPC-positive isolates from this complex.

Optical beam splitter is used for dividing an input optical beam into several separate beams with specific power ratio. Usually, conventional beam splitters have bulky dimensions and fixed dividing ratio which significantly limit the design of new miniaturized optical devices and integrated optical circuits. We propose and investigate a novel physical concept of a miniaturized planar optical splitter/coupler with a switching element in the form of a photonic molecule (PM) pair dispersing input optical fluxes along multiple ways with variable power proportions. The structural design of the proposed splitter is based on a silicon-on-insulator (SOI) platform and composed of high-quality resonators in the form of electromagnetically coupled submicron-sized microcylinders. The control on the power division ratio and the selection of optical beam directions is realized by tuning the photonic splitter structure to the corresponding resonance of PM supermode. Compared to known analogues, the proposed design is easy to fabricate, suitable for integration into a "System-on-a-chip" platform and can dynamically change the beam power division ratio by input wave-phase manipulation.

The integration of renewable energy and hybrid energy storage system (HESS) into electrified railways to build electric railway smart microgrid system (ERSMS) is beneficial for reducing fossil fuel consumption and minimizing energy waste. However, the fluctuations of renewable energy generation and traction load challenge the energy management effectiveness for such a complex system. In this work, an energy management strategy is proposed which firstly decomposes the renewable energy into low-frequency and high-frequency components by an integrated empirical mode decomposition (IEMD). Then, a two-stage energy distribution approach is utilized to appropriately distribute the energy flow among the ERSMS. Finally, the feasibility and effectiveness of the proposed solution are validated through case study.

Cardiotonic steroids (CTS) are a group of steroid compounds derived from certain plants and animals. CTS are selective inhibitors of Na,K-ATPase, so for a long time they were widely used for medical purposes to treat heart failure and some other diseases. However, over time, doctors gradually began to refuse this group of drugs due to their narrow therapeutic range and a number of serious side effects. However, in parallel with the rise and fall of interest in CTS as a drug, interest in them as a single class of high-affinity Na,K-ATPase inhibitors has only increased. Numerous data on the effect of CTS on signaling cascades and cell viability made impelling a search for a rationale for the existence of such a subtle biological regulator. A large number of studies devoted to the potential use of CTS in the treatment of neurodegenerative, oncological, immune and other diseases "revitalized" the already "written off" group of the drugs. If initially the role of exogenous (mainly plant origin) CTS was studied, then by the 90s of the XX century the study of the role of endogenous CTS and their regulatory effects became a popular trend in biology and physiology. The role of endogenous CTS was studied in details in the pathogenesis of cardiovascular diseases [1]. A large number of researchers have unanimously stated that endogenous CTS are very complex regulators of the development of pathological processes; however, the exact cause-and-effect relationship that would unambiguously explain the processes of synthesis, utilization, and the role of endogenous CTS has not yet been established. The effects of CTS in the frame of various regulatory schemes have been described, but the predominant number of studies was devoted to arterial hypertension, heart and renal failure, cancer [2–4], aging [5,6], and neuroinflammation. The effects of both endo- and exogenous CTS on blood cells and have been studied to a much lesser extent.

In the era of digital advancements, the escalation of credit card fraud necessitates the development of robust and efficient fraud detection systems. This paper delves into the application of machine learning models, specifically focusing on ensemble methods, to enhance credit card fraud detection. Through an extensive review of existing literature, we identified limitations in current fraud detection technologies, including issues like data imbalance, concept drift, false positives/negatives, limited generalisability, and challenges in real-time processing. To address some of these shortcomings, we propose a novel ensemble model that integrates a Support Vector Machine (SVM), K-Nearest Neighbor (KNN), Random Forest (RF), Bagging, and Boosting classifiers. This ensemble model tackles the dataset imbalance problem associated with most credit card datasets by implementing under-sampling and the Synthetic Over-sampling Technique (SMOTE) on some machine learning algorithms. The evaluation of the model utilises a dataset comprising transaction records from European credit card holders, providing a realistic scenario for assessment. The methodology of the proposed model encompasses data pre-processing, feature engineering, model selection, and evaluation, with Google Colab computational capabilities facilitating efficient model training and testing. Comparative analysis between the proposed ensemble model, traditional machine learning methods, and individual classifiers reveals the superior performance of the ensemble in mitigating challenges associated with credit card fraud detection. Across accuracy, precision, recall, and F1-score metrics, the ensemble outperforms existing models. This paper underscores the efficacy of ensemble methods as a valuable tool in the battle against fraudulent transactions. The findings presented lay the groundwork for future advancements in the development of more resilient and adaptive fraud detection systems, crucial as credit card fraud techniques continue to evolve.

For years, effort has been devoted to establishing an effective bull breeding soundness evaluation procedure; usual research on the subject is based on BBSE (Bull Breeding Soundness Examination) methodologies, which have significant limitations in terms of their evaluation procedure, such as high cost, time-consuming and administratively difficult. This research focuses on the creation of a prediction model to supplement and/or improve the BBSE approach, through the study of two algorithms, Clustering and Artificial Neural Network (ANN), to find the optimum Machine Learning (ML) approach for our application, with an emphasis on data categorization accuracy. The tool is designed to assist veterinary medicine and farmers in identifying key factors and increasing certainty in their decision-making during the selection of bulls for breeding purposes, providing data from a limited number of factors generated from a deep pairing study of bulls. Zebu Bulls, European Bulls, and Crossbred Bulls were the general groupings. The data utilized in the model's creation (N =359) considers five variables that influence improvement decisions. This approach enhances decision-making by 12%. ANN obtained an accuracy of 90%; Precision was 97% for satisfying, 92% for unsatisfying, and 85% for Bad.

Reactions of N‚N'-bis(3-methylpyridyl)oxalamide (L1), N,N’-bis(3-methylpyridyl)adipoamide (L2) and N,N’-bis(3-methylpyridyl)sebacoamide (L3) with tricarboxylic acids and Cu(II) salts afforded {[Cu(L1)(1,3,5-HBTC)]·H2O}n (1,3,5-H3BTC = 1,3,5-benzenetricarboxylic acid), 1, {[Cu1.5(L2)1.5(1,3,5-BTC)(H2O)2]·6.5H2O}n, 2, [Cu(L2)0.5(1,3,5-HBTB)]n (1,3,5-H3BTB = 1,3,5-tri(4-carboxyphenyl)benzene), 3, [Cu4(L3)(OH)2(1,3,5-BTC)2]n, 4, {[Cu3(L3)2(1,3,5-BTB)2]·2.5MeOH·2H2O}n, 5, and {[Cu3(L3)2(1,3,5-BTB)2 ]·DMF·2H2O}n, 6, which have been structurally characterized by using single crystal X-ray crystallography. Complexes 1 – 4 form a 2D layer with the {44.62}-sql topology, a 2D layer with the (4.62)2(42.62.82)-bex topology, a 3-fold interpenetrated 3D net with the (412.63)-pcu topology and a 3D framework with the (410.632.83)(42.6)2(43.63) topology, respectively, whereas 5 and 6 are 3D frameworks with the (63)2(64.82)(68.85.102) topology. Complex 5 shows a better iodine-adsorption factor of 290.0 mg g-1 at 60 oC for 360 minutes than the other ones, revealing that the flexibility of the spacer ligand governs the structural diversity and the adsorption capacity.

Historically, macrophages have been long implicated in the control of the severity of infectious diseases. This has been based on the observations of a higher risk of severe disease and death upon rechallenge with viral variants due to antibody dependent enhance-ment (ADE) of infection into macrophages. The question remains as to what can account for this potent heterologous protection in macrophages? Here it is argued that the elusive defense mechanism of M1-like pro-inflammatory macrophages may pertain to a novel virus anti-virus response. This system initiates with high replication of human endogenous retrovirus K102 (HERV-K102), a non-pathogenic, protector foamy retrovirus of humans which generates M1-like pro-inflammatory foamy macrophages, glycolysis, and epigenetic changes, all characteristic of trained immunity. This virus-anti-virus system kills virally infected cells by several mechanisms, amplifies the innate interferon response via ‘viral mimicry’, has many unique components that interfere with exoge-nous virus replication, and may be especially adept at neutralizing enveloped exogenous pandemic viruses, such as SARS-CoV-2 and HIV-1. The goal of this treatise is to introduce the multifaceted HERV-K102 protector system, to illustrate how SARS-CoV-2 may target the HERV-K102 protector system by ADE, and to explore how this innate defense system may be exploited for pandemic preparedness.

The Centers for Disease Control and Prevention (CDC) indicates that individuals with prediabetes are significantly less likely to develop type 2 diabetes if they participate in a lifestyle change program that results in at least 5% weight loss and 150 minutes of physical activity per week. The CDC recognizes distance learning as an effective delivery mode for lifestyle change programs to prevent type 2 diabetes. The purpose of this study was to assess enrollment, engagement, and effectiveness of a type 2 diabetes prevention program (DPP) using synchronous distance technology. Eat Smart, Move More, Prevent Diabetes (ESMMPD) is an intensive 12-month DPP delivered using synchronous distance technology. Throughout 26 lessons, participants focused on healthy eating, physical activity, and mindfulness behaviors. Study findings showed a significant decrease in A1C (-0.24 p<.0001). Weight loss averaged 5.66% for those who completed the program. Based on the Wilcoxon signed-rank test, participants demonstrated statistically significant changes in self-reported confidence in their ability to perform all 18 health-promoting behaviors assessed (p<.0001). Participation in the program also resulted in the adoption of health promoting behaviors. A DPP using synchronous distance technology is an effective delivery mode to help participants adopt healthy behaviors, increase physical activity, and achieve the weight loss necessary to prevent or delay the onset of type 2 diabetes.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

: Drought monitoring and early detection have improved greatly in recent decades through the development and refinement of numerous indices and indicators. However, a lack of guidance, based on user experience, exists as to which drought monitoring tools are most appropriate in a given location. This review paper summarizes the results of targeted user engagement and the published literature to improve the understanding of drought across North America, and to enhance the utility of drought monitoring tools. Workshops and surveys were used to assess and make general conclusions about the perceived performance of drought indicators, indices and impacts information used for monitoring drought in the five main Köppen climate types (Tropical, Temperate, Continental, Polar Tundra, Dry) found across Canada, Mexico, and the United States. In Tropical, humid Temperate, and southerly Continental climates, droughts are perceived to be more short-term (less than 6 months) in duration rather than long-term (more than 6 months). In Polar Tundra climates, Dry climates, Temperate climates with dry warm seasons, and northerly Continental climates, droughts are perceived to be more long-term than short-term. In general, agricultural and hydrological droughts were considered to be the most important drought types. Drought impacts related to agriculture, water supply, ecosystem, and human health were rated to be of greatest importance. Users identified the most effective indices and indicators for monitoring drought across North America to be the U.S. Drought Monitor (USDM) and Standardized Precipitation Index (SPI) (or another measure of precipitation anomaly), followed by the Normalized Difference Vegetation Index (NDVI) (or another satellite-observed vegetation index), temperature anomalies, crop status, soil moisture, streamflow, reservoir storage, water use (demand), and reported drought impacts. Users also noted the importance of indices that measure evapotranspiration, evaporative demand, and snow water content. Drought indices and indicators were generally thought to perform equally well across seasons in Tropical and the colder Continental climates, but their performance was perceived to vary seasonally in Dry, Temperate, Polar Tundra, and the warmer Continental climates, with improved performance during warm and wet times of the year. The drought indices and indicators, in general, were not perceived to perform equally well across geographies. This review paper provides guidance on when (time of year) and where (climate zone) the more popular drought indices and indicators should be used. The paper concludes by noting the importance of understanding how drought, its impacts, and indicators are changing over time as the climate warms, and by recommending ways to strengthen the use of indices and indicators in drought decision-making.

This paper describes RTMN 2.0 - an extension of the modeling language RTMN. RTMN combines process modeling and robot execution. The reusability and intuitive robot programming allows people without programming expertise to plan and control robots. While RTMN focuses on the ease of use and flexibility of robot programming by providing an intuitive modelling language, RTMN 2.0 concentrates on Human Robot Collaboration (HRC), which represents the current trend of the industry shift from ‘mass-production’ to ‘mass-customization’. While traditional robot systems provide high payload capabilities and repeatability, they suffer from limited flexibility and dexterity. Therefore, human-robot collaboration is a suitable arrangement to leverage the unique capabilities of both humans and robots for increased efficiency and quality in industrial scenarios. HRC has made a great impact on the robotic industry: increased efficiency, reduced costs and improved productivity, which can be adopted to make up for the skill gap of a shortage of workers in the manufacturing industry. The extension in RTMN 2.0 includes the following notations: HRC tasks, requirement, Key Performance Indicator (KPI), condition check and decision making, join/split and data association. With all these additional elements RTMN 2.0 covers the full scale of agile manufacturing – light out and collaborative.

High concentrations of sodium (Na+), chloride (Cl-), calcium (Ca2+), and sulphate (SO42-) are fre-quently found in saline soils. Crop plants cannot successfully develop and produce because salt stress impairs the uptake of calcium, potassium, and water into plant cells. Different intracellular and extracellular ionic concentration changes by salinity, including those of calcium, potassium, and protons. These cations serve as stress signaling molecules in addition to being essential for ionic homeostasis and nutrition. Maintaining an appropriate K+: Na+ ratio is one crucial plant mechanism for salt tolerance, which is a complicated trait. Another important mechanism is the ability for fast extrusion of Na+ from the cytosol. Calcium is established as a ubiquitous secondary messenger, which transmits various stress signals into metabolic alterations that cause adaptive responses. When plants are under stress, the cytosolic-free Ca2+ concentration can rise to 10 times or more from its resting level of 50-100 nanomolar. Reactive oxygen species (ROS) are linked to the calcium alterations, and are produced by stress. Depending on the type, frequency and intensity of the stress, the cytosolic calcium signals oscillate, are transient, or persist for a longer period and exhibit specific "signatures". Both the input and efflux of Ca2+ from the cytosol affect the length and amplitude of the signal. According to several reports, under stress calcium alterations can occur not only in the cytoplasm of the cell but also in the cell walls, nucleus and other cell organelles and the calcium waves propagate through the whole plant. Here, we will focus on how wheat and other important crops absorb Na+, K+ and Cl- when plants are under salt stress, as well as how calcium, potassium, and pH cause intracellular signaling and homeostasis. Similar mechanisms in the model plant Arabidopsis will also be considered.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

The wind flow patterns and pressure distribution around a plus-shaped building are significantly influenced by the dimensions of its re-entrant corners and the overall building height. The present study aims to find the wind effects and study of the pressure distribution with different flow patterns. Plan area of the building is around 300 square meter while the height of the building is 50 meters by keeping the equal length of the re-entrant corners. The research is performed using ANSYS CFX academic version and the results are depicted in various forms such as pressure coefficient (Cpe), stream lines in both vertical as well as in specific surface and pressure contours. The analysis is carried out by varying the wind incident angles, from 0° to 90° at the interval of 15°. The building dimension are scale down to perform the test on length scale of 1:100. Since the considered building model exhibits symmetry along both the axes, present study mostly emphasis on examining re-entrant corners located in the building. This method yields valuable information about how air circulates and how pressure is distributed across a broad spectrum of wind angles. This study provides valuable insights into flow circulation and pressure distribution for a wide range of wind angles.

As distinct human societies, three unique intentional communities are investigated regarding their preferred consensus decision-making practices. It is Identified that each has adopted a different form of consensus decision-making to solve potential group-wide interpersonal conflict. The individual attributes of these three consensus decision-making practices are considered, both from the perspective of maintaining group stability and in relation to individual member's mental health. The communities are a Canadian self-directed public senior elementary and secondary school, an annual English conference for those self-identifying as on the autistic spectrum, and a self-producing Korean popular music (K-pop) group. It is found that the intentional community and participants’ mental health are sustained regarding each of the three consensus decision-making practices. Nevertheless, the resulting decisions generate various stresses within the communities, both as a whole and concerning the individual members. To retain group cohesion and maintain individual mental health, these stresses must be recognized and understood by participants. The novel finding of this research is that, dependent on the time available for decision-making, and the members’ perspective adopted, intentional communities might practice more than one form of consensus decision-making and still support both group cohesion and individual mental health, maintaining the democracy of these distinct societies.

This article investigates on the radial and non-radial geodesic structures of the generalized K-essence Vaidya spacetime. Within the framework of K-essence geometry, it is important to note that the metric does not possess conformal equivalence to the conventional gravitational metric. This study employs a non-canonical action of the Dirac-Born-Infeld kind. In this work, we categorize the generalized K-essence Vaidya mass function into two distinct forms. Both the forms of the mass functions have been extensively utilized to analyze the radial and non-radial time-like or null geodesics in great details inside the comoving plane. Indications of the existence of wormhole can be noted during the extreme phases of spacetime, particularly in relation to black holes and white holes, which resemble the Einstein-Rosen bridge. In addition, we have also detected the distinctive indication of the quantum tunneling phenomenon around the central singularity.

This paper presents a new low-voltage versatile mixed-mode filter which uses a multi-ple-input/output differential difference transconductance amplifier (MIMO-DDTA). The multi-ple-input of the DDTA is realized using a multiple-input bulk-driven MOS transistor (MI-BD-MOST) technique to maintain a single differential pair, thereby achieving simple structure with minimal power consumption. In a single topology, the proposed filter can provide five standard filtering functions (low-pass, high-pass, band-pass, band-stop, and all-pass) in four modes: voltage (VM), current (CM), transadmittance (TAM), and transimpedance (TIM). This provides the full capability of a mixed mode filter (i.e., twenty filter functions). Moreover, the VM filter offers high-input and low-output impedances and the CM filter offers high-output impedance; therefore, no buffer circuit is needed. The natural frequency of all filtering functions can be electronically controlled by a setting current. The voltage supply is 0.5 V and for a 4 nA setting current, the power consumption of the filter was 281 nW. The filter is suitable for low-frequency biomedical and sensor applications that require extremely low supply voltages and nano-watt power consumption. For the VM low-pass filter, the dynamic range was 58.23 dB @ 1 % total harmonic distortion. The proposed filter was designed and simulated in the Cadence Virtuoso System Design Platform using the 0.18 µm TSMC CMOS technology.

Historic sites are important components of every city's cultural history because they preserve rich historical knowledge and distinctive values passed down from previous generations to the present. Due to the progress of urbanization and modernization, many historic sites face pressure from damage and transformation. In this paper, a method for assessing cultural heritage damage was developed to measure the extent of spatial damage in historic sites. Using sample data obtained in Xiyang, Qixian, and Xiaoyi, all historic cities in Shanxi Province, Mainland China, and combined weights were estimated using the Delphi technique and the CRITIC weight method. Following this, the Spatial Damage Degree Model (SDDM) based on K-means cluster analysis and K-nearest neighbor (KNN) classification was developed. The findings show that the model efficiently solves the problem of assessing spatial damage levels in historic sites. Through multiple linear regression analysis, it was shown that the damage to historic sites was predominantly caused by three factors: natural erosion, construction damage, and planning and policy. SDDM was used to calculate the spatial damage levels of historic sites, allowing conservators to fully comprehend the features and concerns related to historic sites. As a result, more scientific and rational preservation approaches may be developed, improving the efficiency of historic site restoration and conservation and encouraging the sustainable development of urban and rural heritage.

The Covid-19 crisis has been one of the most relevant economic shocks in the history of the modern economy, mainly due to the restrictions on travel and social interaction taken by the authorities (quarantines, closure of schools, artistic activities, bars, and restaurants, capacity in stores), to reduce the transmission of the virus (Sars-Cov2), having consequences on the national productions of all countries (about 7% for the loss of GDP worldwide). In our study, we analyze, through clustering methods, the effects of the level of contagion, economic projections, and economic mitigation measures taken by governments for managing the pandemic. According to the analyses, it can be concluded that a low infection rate implies a lower loss of product and economic savings when applying economic mitigation measures, taking relevance in the management of sanitary measures to reduce the transmission of the virus (and the temporality of these).

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

This article is a study on the (k,s)-Riemann-Liouville fractional integral, a generalization of the Riemann-Liouville fractional integral. Firstly, we introduce several properties of the extended integral of continuous functions. Furthermore, we make the estimation of the Box dimension of the graph of continuous functions after the extended integral. It presents that the upper Box dimension of the (k,s)-Riemann-Liouville fractional integral for any continuous functions is no more than the upper Box dimension of the functions on the unit interval I=[0,1], which indicates that the upper Box dimension of the integrand f(x) will not be increased by the σ-order (k,s)-Riemann-Liouville fractional integral ksD−σf(x) where σ&gt;0 on I. Additionally, we prove that the fractal dimension of ksD−σf(x) of one-dimensional continuous functions f(x) is still one.

An algorithm is proposed for discriminating the fatigue state of air traffic controllers based on ap-plying multispeech feature fusion using an FSVM to voice data, and for extracting eye-fatigue-state discrimination features based on PERCLOS eye data. For the speech algorithm and an eye-fatigue index, a new controller fatigue-state evaluation index based on the entropy weight method is proposed based on decision-level fusion of fatigue discrimination results for speech and the eyes. Experimental results show that the fatigue-state recognition accuracy rate was 84.81% for the fatigue state evaluation index, which was 3.36% and 1.86% higher than those for speech and eye assessments, respectively. The comprehensive fatigue evaluation index provides important reference values for controller scheduling and mental-state evaluations.

The utilization of dual-potential mode of integrated array (IDA) electrodes and other two-electrode systems has revolutionized electrochemical detection by enabling the simultaneous and independent detection of two species, accompanied by the exhibition of unique characteristics. In contrast to conventional dual-potential electrodes, the rotating ring disk electrodes (RRDE), IDA electrodes demonstrate analogous yet vastly improved performance metrics, characterized by remarkable collection efficiency and sensitivity. Notably, due to the distinctive microscale structure of IDA electrode, the special “feedback” effect makes IDA a unique signal amplifier. In recent decades, the research surrounding IDA electrodes has garnered escalating interest due to their attractive attributes. This review centers its focus on the fabrication and applications of IDA electrodes. In the realm of fabrication, two critical breakthroughs are poised for realization: the achievement of reduced dimensions and the diversification of materials. Established fabrication methods for IDA electrodes encompass photolithography, inkjet printing, and direct laser writing, each affording distinct advantages in terms of size and precision in IDA construction. Predominantly employed materials for IDA electrodes include gold, platinum, and carbon, with the selection of fabrication methods guided by considerations such as material properties, desired dimensions, cost-efficiency, and specific application requisites. Within the domain of applications, IDA electrodes, capitalizing on their distinctive attributes, have found utility in diverse fields. This review summarizes the applications of IDA electrodes based on their fundamental working principles, encompassing redox cycling, resistance modulation, capacitance variations, and more. The potential for further development of this specialized tool to exhibit enhanced properties holds substantial promise.

The current study aims to produce a material that has a dual effect of healing and anti-inflammatory. For this target k-carrageenan/polyacrylamide hydrogel film loaded with cetrimide (k-CAR/PAAm/CI) was performed by manual casting technique. Definite concentrations of k-CAR and AAm was heated at 80°C for 2 hours, CI and glycerol were added. The solution was cast without using initiator and cross-linker. The reaction of the sulfonic acid group -SO3H of k-CAR with -CONH2 group of PAAm lead to the formation of a sulfonamide (-SO2NH-) linkage. The characteristics of the produced films were investigated by FTIR, TGA, contact angle, and mechanical properties. Improvement in the thermal stability was performed in k-CAR/PAAm/CI2 film containing 1.5% CI compared to the film has 0.5% CI (k-CAR/PAAm/CI1). The contact angle measurement proved the films are hydrophobic that enhanced by increasing CI content. The tensile strength and elongation percent values are considered adequate for materials used in wound care. k-CAR/PAAm/CI2 (1.5% CI) film showed superior antimicrobial activity against P. aeruginosa, moderate activity against S. aureus, and low activity against E. coli. The film k-CAR/PAAm/CI2 was effectively inhibiting the heat-induced hemolysis and may offer a promising approach for the development of effective wound dressings.

Magnetorheological (MR) fluids have been known to react to magnetic fields of sufficient magnitudes. While in the presence of the field the material develops a yield stress. The tunable property has made it attractive in e.g. semi-active damper applications in vibration control domain in particular. Within the context of a given application the fluids can be exploited in at least one of the fundamental operating modes of which the so-called gradient pinch mode has been least explored. Contrary to the other operating modes, the MR fluid volume in the flow channel is exposed to a non-uniform magnetic field in such a way that the Venturi-like contraction is developed in a flow channel solely by means of a solidified material in the regions near the walls rather than mechanically driven changes of the channel’s geometry. The pinch mode rheology of the material has made it a potential candidate in developing on a new category of MR valves. By convention, a pinch mode valve features a single flow channel with poles over which non-uniform magnetic field is induced. In this study the authors examine ways of extending the dynamic range of pinch mode valves by employing a number of such arrangements (stages) in series. To accomplish this, the authors developed a prototype of a multi-stage (three-stage) valve, and then compared its performance against that of a single-stage valve across a wide range of hydraulic and magnetic stimuli. To summarize, improvements in the pinch mode valve dynamic range are evident, however, at the same time it is hampered by the presence of serial air gaps in the flow channel.

A micro-ring resonator structure was fabricated via two-photon polymerization (2PP) technique directly on a single-mode fiber tip and tested for refractive index sensing application. The micro-ring structure was used to excite whispering gallery modes (WGMs) and observations of the changes in resonance spectrum introduced by changes in refractive index of the environment served as the sensing principle. The proposed structure has the advantages of a very simple design, allowing for measurements in reflection mode, relatively easy and fast fabrication and integration with a single tip of a standard single-mode fiber, which allowed for quick and convenient measurements in the optical setup. The performance of structure was characterized, resonant spectrum giving high potential for refractive index sensing was measured. Future perspectives of the research are discussed.

Keywords: Requirements prioritization, Next release plan, Software product planning, Decision support, MoSCoW, AHP, K-Menas, GMM, BIRCH, PAM, Hierarchical, Clustering, Clusters Evaluation

The large quantity of information retrieved from communities, public data repositories, web pages, or data mining can be sparsed and poorly classified. This work shows how to employ unsupervised classification algorithms such as K-means proper to classify user reviews into their closest category, forming a balanced data set. Moreover, we found that the text vectorization technique significantly impacts the clustering formation, comparing TF-IDF and Word2Vec. The value for mapping a cluster with movie genre was 81.34% ± 20.48 of the cases when the TF-IDF was applied, whereas Word2Vec only yielded a 53.51% ± 24.1. In addition, we highlight the impact of the removal of stop-words. Thus, we detected that pre-compiled lists are not the best method to remove stop-words before clustering because there is much ambiguity, centroids are poorly separated, and only 57% of clusters could match a movie genre. Thus, our proposed approach achieved a 94% of accuracy. After analyzing the classifiers’ results, we appreciated a similar effect when divided by the stop-words method removal. Statistically significant changes were observed, especially in precision metric and Jaccard scores in both classifiers, using custom-generated stop lists rather than pre-compiled ones. Reclassifying sparse data is strongly recommended as using custom-generated stop lists.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

This study presents an innovative approach named Optimal Adaptive Continuous Barrier Function Terminal Sliding Mode Control (OACBF-TSMC) approach with a novel switching manifold, to control mathematical model of nonlinear systems under model uncertainties and external disturbances. The proposed OACBF-TSMC approach combines the advantages of adaptive control, continuous barrier functions, and terminal sliding mode control to achieve robust stability of the mathematical model of nonlinear systems, and by using a genetic algorithm that tries to optimize the controller parameters as much as possible so that the proposed controller is the most to have efficiency and performance. The proposed method is designed to address the challenges of systems and provide superior performance in terms of stabilization accuracy, disturbance rejection, and robustness against uncertainties. However, the critical challenge facing the proposed controller is the complete elimination of the chattering phenomenon, which is the most important problem of ordinary sliding mode controllers. The simulation results show that the system trajectories in the proposed approach have converged to the origin with minimal overshoot and under-shoot in a finite time; In addition, the chattering problem in the control inputs has been well eliminated, which makes the proposed method suitable for various systems, including chaotic systems, energy sources, and distributed production systems. Furthermore, the OACBF-TSMC approach has the potential to enhance the stability and reliability of control systems, contributing to the integration of the system states.

To verify the concept of the metasurfaced reverberation chamber (MRC) which was proposed. This paper reports on measurements in the reverberation chamber (RC) performance by using a 1-bit random coding metasurfaced stirrer. The measurement results are validated and compared with that from two mechanical stirrers (horizontal stirrer and vertical stirrer). Figures of merit such as quality factor (Q factor), number of samples, standard deviation, angle autocorrelation, average K-factor, total scattering cross section (TSCS) and the enhanced back scattering coefficient (eb) are presented. Results indicate the feasibility of the MRC technique in the operation frequency of the RC. And it is possible to enlarge the test volume of the RC by using the 1-bit random coding metasurface stirrer.

The Review examines studies aimed at the organization of energy (non-mechanical) control of high-speed flow/flight using spatially multi-component plasma structures and combined energy deposition. The Review covers selected works on experimental obtaining and numerical modeling multi-component plasma structures and use of sets of actuators based on the plasma of such a spatially type for the purposes of control of shock wave/bow shock wave – energy source interaction, as well as control of shock wave – boundary layer interaction. A series of works on repetitive multiple laser pulse plasma structures is also analyzed from the point of view of examining shock wave/bow shock wave boundary layer interaction. Self-sustained theoretical models for laser dual-pulse, multi-mode laser pulses and self-sustained glow discharge are also considered. Separate sections are devoted to high-speed flow control using combined physical phenomena and numerical prediction of flow control possibilities using thermal longitudinally layered plasma structures. The wide possibilities for organization and applying spatially multi-component structured plasma for the purposes of high-speed flow control are demonstrated.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

In recent years, the use of long-term seismic monitoring systems for the protection of structures is becoming increasingly widespread. This is because more and more awareness is gradually developing regarding the importance of keeping structures under observation so as to prevent any damage scenarios. Within the field of Structural Health Monitoring, data driven techniques allow to process and analyze data collected on site. This paper presents a Mode Tracking procedure to obtain the time-histories of the natural frequencies of a monumental structure. The procedure is applied on the Sanctuary of Vicoforte, an important monumental structure site in Piedmont known for its imposing oval dome and characterized by a permanent structural monitoring system. Through the procedure presented in the paper it has been possible to obtain and observe the time series of the first natural frequencies of the structure considering various aspects, including the temperature variation.

Finding the ideal statistical method for grouping phenological data is always an important step for breeders to draw correct conclusions from it possibly. In this paper, K-cluster analysis is presented as a perfect tool for grouping phenological data. The present research was performed based on the phenological data of 61 strawberries (Fragaria × ananassa) cultivars of different geo-graphical origins grown in Estonian conditions. Groups of strawberry cultivars were deter-mined according to flowering and ripening time: early, middle and late, based on the sum of ef-fective temperatures above +5°C. The result of the K-cluster analysis carried out in this way makes it possible to precisely plan the ripening time of berries of different strawberry cultivars. Using such analysis data, it is possible to combine with different early, mid or late strawberry cultivars to extend the picking period. Also, this technique can be used to study the effect of cli-matic changes occurring over the years on the phenology of strawberry cultivars grown in the region.

HIV-1 infection can activate the expression of human endogenous retroviruses (HERVs), particularly HERV-K (HML-2). HIV controllers (HICs) are rare people living with HIV (PLWH) who naturally control HIV-1 replication. The ability of HICs to control the expression of endogenous retroviruses has not been previously addressed. In this study, we measured ERVK-6 RNA expression in PBMCs of HICs (n = 23), antiretroviral (ART)-suppressed subjects (n = 8), and HIV-1-negative (NEG) individuals (n = 10) and correlated the transcript expression of ERVK-6 with multiple HIV-1 restriction factors. Our study reveals that ERVK-6 RNA expression in PBMCs from HICs was significantly downregulated compared with both ART and NEG control groups. Moreover, we detected that ERVK-6 RNA levels in PBMCs across all groups were negatively correlated with the expression levels of p21 and MCPIP1. In our previous study, these two cellular restriction factors were upregulated in HICs compared with control groups. Interestingly, p21 and MCPIP1 limit the activation of macrophages and T cells by downregulating the activity of NF-kB, a transcription factor that stimulates the LTR-driven transcription of HIV-1 and HERV-K proviruses. These findings support that HICs activate innate antiviral mechanisms that may simultaneously downregulate the transcription of both HIV-1 and endogenous retroviruses.

Knowing the reasons for mobility choices, how users evaluate the characteristics of public transport and how satisfied they are with the travel experience is essential to promote the use of LTP (Local Public Transport), especially in rural or suburban areas where the use of private car is often prevalent. The present study aimed to investigate the mobility experience and the reasons for use and non-use of the LPT in a suburban area by the people travelling to a large Hospital Centre in a Province of the North-east of Italy. An anonymous questionnaire was completed by people from different categories travelling to the hospital (students, employees, clients), user and non-users of the LPT. The results showed that insufficient hourly coverage and accessibility of the service are the primary reasons for opting not to use LPT and together with reliability and comfort, these factors contribute to user satisfaction with their travel experience. Perceived sustainability of LPT contributes to overall travel satisfaction. However perceived sustainability alone does not appear to influence the choice of LPT if the service lacks adequate accessibility and does not meet the needs of travelers in terms of hourly coverage

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

In the particular configuration of the scalar field K-essence in the Wheeler-DeWitt quantum equation, for some age in the Bianchi type I anisotropic cosmological model, a fractional differential equation for the scalar field arises naturally. The order of the fractional differential equation is $\beta=\frac{2\alpha}{2\alpha - 1}$. This fractional equation belongs to different intervals, depending on the value of the barotropic parameter; when $\omega_{X} \in [0,1]$, the order belongs to the interval $1\leq \beta \leq 2$, and when $\omega_{X}\in[-1,0)$, the order belongs to the interval $0<\beta \leq 1$. In the quantum scheme, we introduce the factor ordering problem in the variables $(\Omega,\phi)$ and its corresponding momenta $(\Pi_\Omega, \Pi_\phi)$, obtaining a linear fractional differential equation with variable coefficients in the scalar field equation, then the solution is found using a fractional power series expansion. The corresponding quantum solutions are also given. We found the classical solution in the usual gauge N obtained in the Hamiltonian formalism and without a gauge. In the last case, the general solution is presented in a transformed time $T(\tau)$, however in the dust era we found a closed solution in the gauge time $\tau$.

Nearest-neighbour clustering is a simple yet powerful machine learning algorithm that finds natural application in the decoding of signals in classical optical-fibre communication systems. Quantum k-means clustering promises a speed-up over the classical k-means algorithm; however, it has been shown to currently not provide this speed-up for decoding optical-fibre signals due to the embedding of classical data, which introduces inaccuracies and slowdowns. Although still not achieving an exponential speed-up for NISQ implementations, this work proposes the generalised inverse stereographic projection as an improved embedding into the Bloch sphere for quantum distance estimation in k-nearest-neighbour clustering, which allows us to get closer to the classical performance. We also use the generalised inverse stereographic projection to develop an analogous classical clustering algorithm and benchmark its accuracy, runtime and convergence for decoding real-world experimental optical-fibre communication data. This proposed `quantum-inspired' algorithm provides an improvement in both the accuracy and convergence rate with respect to the k-means algorithm. Hence, this work presents two main contributions. Firstly, we propose the general inverse stereographic projection into the Bloch sphere as a better embedding for quantum machine learning algorithms; here, we use the problem of clustering quadrature amplitude modulated optical-fibre signals as an example. Secondly, as a purely classical contribution inspired by the first contribution, we propose and benchmark the use of the general inverse stereographic projection and spherical centroid for clustering optical-fibre signals, showing that optimizing the radius yields a consistent improvement in accuracy and convergence rate.

Keywords: Electrical power systems, Support vector machines, Random Forest, Machine learning, Wavelet transform, Transmission lines fault, Electrical power quality, Short circuit, Classification of faults, Localization of faults, Decision trees, Ensemble learning, K-nearest neighbors.

Active transportation, such as walking, cycling, and micro-mobility modes, has received a lot of attention in recent years due to its potential benefits to urban residents, such as less traffic, better air quality, more opportunities to get exercise, and an overall higher quality of life. In this study, we used Classification and Regression Trees (CART) to compare and contrast three mobility options: shared micro-mobility, individual micro-mobility, and walking. We surveyed 219 people living in Budapest, Hungary, to learn more about their travel habits and investigate the demographic elements that influence people's mode choice, such as age, gender, ownership of micro-mobility modes, education, job, and income. Results showed that ownership of personal micro-mobility modes, and age as important predictors of active travel mode choice. Males seem to prioritize cost and weather conditions when choosing shared micromobility modes, while females value safety and weather conditions. Our findings can guide policy decisions and urban planning initiatives by identifying the most significant predictors of mode choice and evaluating the possible benefits and drawbacks of each mode.

Spatiotemporal climate variability is a leading environmental constraint to the rain-fed agricultural productivity and food security of communities in the Abbay basin and elsewhere in Ethiopia. The previous one-size-fits-all approach to soil and water management technology targeting did not effectively address climate-induced risks to rain-fed agriculture. This study, therefore, delineates homogenous climatic regions and identifies climate-induced risks to rain-fed agriculture that are important to guide decisions and selection of site-specific technologies for green water management in the Abbay basin. The k-means spatial clustering method was employed to identify homogenous climatic regions in the study area, while the Elbow method was used to determine an optimum number of the climate clusters. The k-mean clustering used the Enhancing National Climate Services (ENACTS) daily rainfall, minimum and maximum temperatures, and other derived climate variables that include daily rainfall amount, length of growing period (LGP), rainfall onset and cessation dates, and rainfall intensity, temperature, potential evapotranspiration (PET), soil moisture and AsterDEM to define climate regions. Accordingly, 12 climate clusters or regions were identified and mapped for the basin. Clustering a given geographic region into homogenous climate classes is useful to accurately identify and target locally relevant green water management technologies to effectively address local-scale climate-induced risks. The study has also provides a methodological framework that can be used in the other river basins of Ethiopia and indeed elsewhere.

Considering the aging society and budget constraints, a strategy for reforming public transportation welfare policies is essential for sustainability. Among the various transportation welfare policies, fare discount policies are provided to specific age groups, and most countries offer benefits to several public transportation. South Korea provides a fare-free policy limited to subways, and the need for policy modification is emerging due to sustainability problems caused by an aging society. Hence, the scope of the policy should be expanded to all travel modes, but the discount rate should be reduced, or the target group should be reduced in consideration of the budget. This study proposes a travel mode to focus on by city through the preference of the elderly. The latent class model is employed to classfy stated preference data collected from the survey. The estimation results show a significant preference heterogeneity depending on the level of subway supply by region, and a policy focused on subways would be more reasonable in cities with sufficient subway infrastructure. Hence, regarding sustainability, it may be more appropriate to focus on specific means than to provide the same discount policy for all public transport.