The deterioration of gait can be used as a biomarker for ageing and neurological diseases. Continuous gait monitoring and analysis are essential for early deficit detection and personalized rehabilitation. The use of mobile and wearable inertial sensor systems for gait monitoring and analysis have been well explored with promising results in the literature. However, most of these studies focus on the technologies for gait characteristic assessment, few of them have considered the data acquisition bandwidth of the sensing system. Inadequate sampling frequency will sacrifice signal fidelity, thus leading to an inaccurate estimation especially for spatial gait parameters. In this work, we developed an inertial sensor based in-shoe gait analysis system for real-time gait monitoring and investigated the optimal sampling frequency to capture all the information on walking patterns. An exploratory validation study was performed using an optical motion capture system on four healthy adult subjects, where each person underwent five walking sessions, giving a total of 20 sessions. Percentage mean absolute errors (MAE%) obtained in stride time, stride length, stride velocity, and cadence while walking were 1.19%, 1.68%, 2.08%, and 1.23%, respectively. In addition, an eigen-analysis based graphical descriptor from raw gait cycle signals was proposed as a new gait metric that can be quantified by principal component analysis to differentiate gait patterns, which has great potential to be used as a powerful analytical tool for gait disorder diagnostics.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

The Eurasian grapevine (Vitis vinifera L.) is the most widely grown horticultural crop in the world and is important for the economy of many countries. In the wine production chain, grape varieties play an important role as they directly influence the authenticity and classification of the product. Identifying the different grape varieties is therefore fundamental for quality control and inspection activities, as well as for regulating production. Currently, ampelography and molecular analysis are the main approaches to identifying grape varieties. However, both methods have limitations. Ampelography is subjective and prone to errors and is experiencing enormous difficulties as ampelographers are increasingly scarce. On the other hand, molecular analyses are very demanding in terms of cost and time. In this scenario, Deep Learning (DL) and Machine Learning (ML) methods have emerged as a classification alternative to deal with the scarcity of ampelographs and avoid molecular analyses. In this study, the most recent and current methods for identifying grapevine varieties using DL classification-based approaches are presented through a systematic literature review. The classification pipeline of the 31 studies found in the literature was described, highlighting its pros and cons. Most of the studies used DL-based models trained with leaf images acquired in a controlled environment at a maximum distance of 1.2 metres to classify grape varieties. In addition, there is a large gap between practical applications and the datasets used: a great lack of varieties, limited data acquired in the field and a lack of tests on plants under adverse conditions. Potential directions for improving this area of research were also presented.

Human detection from Unmanned Aerial Vehicles (UAV) is gaining popularity in the field of disaster management, crowd counting, people monitoring. Real time human detection from UAV is a challenging task, because of many constraints involved. This study proposes a system for real time detection of humans on videos captured from UAVs addressing three of these constraints namely, flying height, computation time and scale of viewing. The proposed method integrated an android application with a binary classifier based on Haar-features to automatically detect human / non-human class from UAV images. The video frames were parsed and detected humans from image frames were geo-localized and visualized on Google Earth. The performance was evaluated for geo-localization accuracy, computation time and detection accuracy, considering human coverage – pixel size relationship for various heights and scale factor. Based on flying height - human size relationship and tradeoff between detection accuracy vs computation time, the study came up with optimal parameters for OpenCV’s cv2.cascadeClassifier. detectMultiScale function. This paper establishes a strong ground for further research relating to real time human detection from UAV.

The Virus HIV-1 infection still represents a serious disease even if actually it is transformed in chronic pathology. Considering the crucial role of the enzyme Protease in life cycle of HIV many efforts have been made in the research of new organic compounds showing inhibitory activity. After development of several series of non peptidic inhibitors we report here the synthesis of novel simple HIV-Protease inhibitors containing heteroaryl carboxamides and their antiviral activity in vitro and in HEK293 cells. Benzofuryl- benzothienyl- and indolyl rings as well as aryl sulfonamides with different electronic properties have been introduced by efficient synthetic procedures. All compounds showed inhibitory activity similar to the commercial drug Darunavir, effective against both wild-type HIV-1 protease and that containing the V32I or V82A mutations. ADME properties were also evaluated, showing the potential of such compounds to be developed as drugs.

The purpose of this study was to explore the association of cognition with hazardous drinking and alcohol related disorder in persons with bipolar disorder (BD). The study population included 1,268 persons from Finland with bipolar disorder. Alcohol use was assessed through hazardous drinking and alcohol related disorder including alcohol use disorder (AUD). Hazardous drinking was screened with the AUDIT-C (Alcohol Use Disorders Identification Test for Consumption) screening tool. Alcohol related disorder diagnoses were obtained from the national registrar data. Participants performed two computerized tasks from the Cambridge automated neuropsychological test battery (CANTAB) on tablet computer: the 5-choice serial reaction time task, or, reaction time (RT) test and the Paired Associative Learning (PAL) test. Association between RT-test and alcohol use was analyzed with log-linear regression, and eβ with 95% confidence intervals (CI) are reported. PAL first trial memory score was analyzed with linear regression, and β with 95% CI are reported. PAL total errors adjusted was analyzed with logistic regression and odds ratios (OR) with 95% CI are reported. After adjustment for age, education and housing status, hazardous drinking was associated with lower median and less variable RT in females while AUD was associated with a poorer PAL test performance in terms of the total errors adjusted scores in females. Our findings of positive associations between alcohol use and cognition in persons with bipolar disorder are unique.

GbtXyl43A, a β-xylosidase that is isolated from Geobacillus thermoleovorans IT-08 and grouped in GH43 family. The substitution of 121Asp residue with Asn in GbtXyl43A caused decrease the enzyme activity. The aim of this study, determine the kinetic characteristics of wild-type GbtXyl43A and D121N variant using Vmax, KM, kcat, and kcat/KM. These parameters indicated catalytic mechanism of GbtXyl43A and its derivative. All of them were produced in Escherichia coli BL21 star. The purification of wild-type GbtXyl43A using affinity chromatography, but D121N variant also required anion-exchange chromatography. The specific activity of wild-type GbtXyl43A and D121N variant were 0.471 U mg-1 in purity level 55,44 and 0.012 U mg-1 in purity level 2,407, respectively. Both enzymes had same molecular weight, ~58 kDa. The kinetic parameters of wild-type GbtXyl43A were KM: 2.845 mM, kcat: 0.033 s-1, Vmax: 0.0033 mM min-1and kcat/KM: 0.0115 s-1mM-1. Furthermore, the KM, kcat, Vmax, and kcat/KM values of D121N variant were 4.565 mM, 1.01 × 10-4 mM min-1, 0.140 × 10-4 s-1, and 0.0307 s-1mM-1, respectively. The KM value of the D121N variant was higher than its wild type and showed the affinity of D121N variant was lower than GbtXyl43A

This manuscript presents a system that can generate a 2D grid map and a 3D voxel model of an environment by fusing multiple sensors integrated into a robot. The fusion of these sensors is done by utilizing Robot Operating System (ROS) and some of its libraries. The sensors that are fused in the robot are a Light Detection and Ranging (LIDAR), Inertial Measurement Units (IMU), wheel encoders, and a Time-of-Flight camera. With the fusion of the point cloud data information obtained with the Time-of-Flight camera, the laser information of the LIDAR sensor, in addition to the odometry generated with the other sensors, a 2D grid map and a 3D model of two different environments were created, thus testing the performance of the system.

The modern supply chain (SC) is growing in terms of data, devices, users, and stakeholders, which introduced new security challenges and threats, especially with the reliance on centralized servers or cloud platforms. In addition, increased trust among system participants exposes the SC to a higher risk of vulnerabilities which require strong security measures. This article proposes a hybrid security framework for SC systems, BC-DRLzSC, that integrates Blockchain (BC) and Deep Reinforcement Learning (DRL) designed to operate in a zero trust (ZT) environment. In particular, we propose a decentralized BC-based approach integrated with smart contracts to manage system participant registration and authentication and to control access to system resources. BC-DRLzSC adopts a ZT architecture to reinforce SC security, which can be achieved with an advocate to verify each entity’s trustworthiness before granting or retaining access to system resources. Incorporating the ZT architecture, with BC and DRL, can potentially and significantly bolster SC system security. DRL is employed to develop a proactive attack detection model that continuously monitors the incoming traffic from authenticated nodes within the network and predicts any malicious actions. Finally, we evaluate the performance of our proposed DRL solution using the NSL-KDD dataset.

The container relocation problem (CRP) is one of the important topics in container terminals, which aims to find the optimal sequence of movements to minimize the total number of relocations needed to retrieve all the containers within a bay according to a given specific layout and retrieval order. However, determining such an order may be difficult due to uncertainty. Various CRP solution methods proposed so far show a common pitfall concerning the complexity of the solving process, whose scale grows exponentially with the number of containers. Considering the retrieval operation process of the inbound containers in a bay consists of several operation rounds, this paper focuses on the real-time operation scenario of each round to minimize the actual number of relocations during the pick-up process, i.e., starting from the initial layout of the bay, we minimize the sum of the incremental number of blocking containers due to the layout change and the number of reallocated containers unrelated to the target container. We present a heuristic algorithm (called SPFH) based on the three rules (LL, MSS, and FSS), considering the adjustment of the pick-up order of containers. Numerical experiments on a set of instances generated from the literature are performed. The proposed methodology excels in both execution efficiency and solution quality and is capable of solving instances that were impossible to solve before. This also makes our methods appealing for being applied in practice. The source codes are available at https://github.com/zhou-sf/rt-scrp.

In this paper, a complete tool for real-time detection of atypical energy behaviors of airplanes is presented. The methodology extends in real time an existing offline process using Dubins trajectories as a predictor of the remaining distance to the runway threshold. Two major contributions are presented in this paper. First, a real-time measure of the aircraft energy behaviour is defined, indicating whether the aircraft is in good condition to intercept the extended runway centreline from its current position. Secondly, a 2D trajectory suggestion is given, allowing safe management of the approach path according to atypical criteria of historical data. Finally, this document proposes a comprehensive tool for air traffic controllers, which is a major step forward in understanding, becoming aware of and resolving critical situations that could lead to accidents.

For Interferometry Synthetic Aperture Radar (InSAR), the normal baseline is one of the main factors that affect the accuracy of the ground elevation. For Gaofen-3 (GF-3) InSAR processing, the poor accuracy of the real-time orbit determination resulting in a large baseline error, leads to the modulation error in azimuth and the slope error in range for timely Digital Elevation Model (DEM) generation. In order to address this problem, a baseline estimation method based on external DEM is proposed in this paper. Firstly, according to the characteristic of the real-time orbit of GF-3 images, orbit fitting is executed to remove the non-linear error factor. Secondly, the height errors are obtained in slant-range plane between Shuttle Radar Topography Mission (SRTM) DEM and the GF-3 generated DEM after orbit fitting. At the same time, the height errors are used to estimate the baseline error which has a linear variation. In this way, the orbit error can be calibrated by the estimated baseline error. Finally, DEM generation is performed by using the modified baseline and orbit. This procedure is implemented iteratively to achieve a higher accuracy DEM. Based on the results of GF-3 interferometric SAR data for Hebei, the effectiveness of the proposed algorithm is verified and the accuracy of GF-3 real-time DEM products can be improved extensively.

Objectives: The study aimed to develop a deep learning-based edge AI model deployed on electrocardiograph (ECG) devices for real-time detection of atrial fibrillation (AF)-risk during sinus rhythm (SR) using standard 10-second 12-lead electrocardiograms (ECGs). Methods: A novel approach was used to convert standard 12-lead ECGs into binary images for model input, and a lightweight convolutional neural network (CNN)-based model was trained using data collected by the Japan Agency for Medical and Research Development (AMED) between 2019 and 2022. Patients over 40 years old with digital, SR ECGs were retrospectively enrolled and divided into AF and non-AF groups. Data labeling was supervised by cardiologists. The dataset was randomly allocated into training, validation, and internal testing datasets. External testing was conducted on data collected from other hospitals.　Results: The best-trained model achieved an AUC of 0.82 and 0.80, sensitivity of 79.5% and 72.3%, specificity of 77.8% and 77.7%, precision of 78.2% and 76.4%, and overall accuracy of 78.6% and 75.0% in the internal and external testing datasets, respectively. The deployed model and app package utilized 2.5MB and 40MB of the available ROM and RAM capacity on the edge ECG device, correspondingly. Processing time for AF-risk detection was approximately 2 seconds.　Conclusion: The model maintains comparable performance and improves its suitability for deployment on resource-constrained ECG devices, thereby expanding its potential impact to a wide range of healthcare settings. Its successful deployment enables real-time AF-risk detection during SR, allowing for timely intervention to prevent AF-related serious consequences like stroke and premature death.

The adaptive immune system in vertebrates comes in two flavors. Historically, adaptive immunity focused on the study of immunoglobulins (also referred to as Ig-based antibodies herein); more recently, jawless vertebrates were found to use an entirely different class of proteins for their adaptive immunesystem. Specifically, these organisms express variable lymphocyte receptors (so called VLR antibodies) that create diversity based on the rearrangement of leucine-rich repeats. Meanwhile, various, naturally occurring repeat motifs have been used as building blocks for the design of artificial binding scaffolds which, among others, include designed ankyrin repeat proteins (DARPins). Such binding scaffolds are also referred to as non-Ig-based antibodies or non-Ig scaffolds herein). DARPins display several benefits such as a low molecular weight (~15 kDa), high thermal stability, high specificity and affinity, versatility (e.g., in terms of valency and multi-specificity), speedy preclinical development, low production costs and, thus, bear the potential to not only complement existing therapeutic Ig-based antibodies but also open up novel therapeutic strategies. The first generation DARPin therapeutic abicipar pegol has completed two Phase III studies in 2020 while several other DARPin drug candidates are currently undergoing clinical validation. Most recently, the rapid development of tri-specific SARSCoV-2 DARPin therapeutics showcases the immense potential of recombinant repeat proteins in adopting quickly e.g., new forms of target neutralization that a single Ig-based antibody cannot afford. Here, we highlight the design principles of repeat proteins in general and summarize in detail the continuous advancements of the DARPin scaffold that made it one of the most promising antibody mimetics to date. This review provides an overview of current and emerging applications of DARPins as both a research tool and therapeutic drug that can match or even surpass Ig-based antibody applications.

Salmonella is a foodborne pathogen associated with localized outbreaks that potentially pose a huge risk to the public health in some countries such as Africa and India, especially in the regions lacking health care measures. The focus of the present study is the molecular detection method of salmonella. The study was conducted to identify Salmonella strains by PCR targeting flagellin specific gene from suspected patient’s clinical blood samples. Serologically, Widal test results showed that all serum samples except one patient (ID 7) were positive for O antigen. The serum of three patients (ID 4, 5 and 10) were found to be positive for H and O antigens while one patient (ID 9) showed agglutination for antigen H. The PCR approach used in this study was successful for fast and precise detection of clinically related Salmonella Typhi. Seven samples out of 10 were positive for Salmonella Typhi as fragments of 458-497bp were observed on the gel-agarose 0.8% corresponds to flagellin gene of S. Typhi. Relatively, smaller amplicons of 366-343bp were observed utilizing nested PCR as well, which seems more sensitive than the conventional PCR. Therefore, we recommend the PCR approach performed in this study to be used as a fast, cost-effective, and time-consuming tool for diagnostic purposes of Salmonella.

B-cell chronic lymphocytic leukemia (B-CLL) is the most common type of leukemia in the Western world. Mutations in different genes, such as TP53 and ATM, and deletions in specific chromosomal regions, including 11q or 17p, have been associated with a worse prognosis for the disease. Recent research from our group has demonstrated that, contrary to the usual cancer development process through missense mutations, B-CLL is driven by the overexpression of the small GTPase RRAS2 in its wild-type form, without activating mutations. While some mouse models of this disease have been developed to date and are commonly used in B-CLL research, they come with various disadvantages, such as a long waiting period until the leukemia fully develops, the need for cell engraftment, or, in some cases, a failure to replicate the alterations found in human patients. We have recently introduced Rosa26-RRAS2fl/flxmb1-Cre as a new mouse model of B-CLL with full disease penetrance. In this work, we have validated this mouse model as a novel tool for the development of new therapies for B-CLL by testing two of the most widely applied targeted agents: ibrutinib and venetoclax. This also paves the way for the development of new targeted agents against R-RAS2 itself, an approach that has not yet been explored in clinical practice.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

Influence of reaction time on silver nanoparticles-catalyzed oxidation of 3,3’,5,5’-tetramethylbenzidine (TMB) was evaluated via probing the oxidation process by recording the UV-Visible absorbance of the resulting colored products of TMB oxidation by hydrogen peroxide in the presence of silver nanoparticles as peroxides mimics. The time curve of the oxidation process was constructed, revealed that the concentration of the oxidation product was increased by increasing the reaction time and then levled off because the nanozyme active nodes were saturated after a certain reaction time and consequently the steady-state condition can be observed. The maximal activity of the silver nanozymes was achieved after a very short reaction time as short as 3.0 min and after this time, the color intensity of the oxidation products remained constant, revealing saturation of active nodes of nanoparticles with nanozyme-substrate.

We investigated humoral immune responses in 222 unvaccinated Japanese people after recovery from severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection in 2021. Anti-spike protein IgG antibody levels and neutralizing antibody titers were measured in serum samples obtained within 20–180 days after diagnosis. The geometric mean of antibody titers was 1555 ELU/mL (95% confidence interval [CI] = 1257-1923), and the neutralizing activities (50% inhibitory dilution) was 253 (95% CI = 204-313). The antibody titer and neutralizing activity both increased with increasing disease severity, and both values were approximately 4-fold higher for hospitalized patients than for non-hospitalized patients. However, these differences were smaller in older patients. The humoral immune response, which increased with increasing disease severity, gradually decreased over time after SARS-CoV-2 infection. Most patients with mild or moderate symptoms sustained neutralizing activity for up to 180 days after the infection, the decay of the neutralizing activity in the patients with asymptomatic was rather faster than other groups. 11.7% (26/222) of patients had very low neutralizing activity, and half of these were in the age of 20s. Our study results show the importance of measuring the neutralizing activity to confirm the immune status and also estimate the timing of vaccine.

Different types of disasters, whether natural or human character, lead to the significant loss of human lives. In the latter case, the quick action of identification of corpses and human remains is mandatory. There are a variety of protocols to identify victims, however, genetics is one of the tools that allow an exact identification of the victim. However, several factors may interfere with this identification, from the biological samples’ degradation not allowing the analysis of nuclear information, to failure to dispose of biological samples from family members. Access to certain family members could be a determinant of the proper choice of genetic markers that allow the identification of the victim, or his/her inclusion in a given genetic maternal or paternal lineage. With the new advances in the genetic field, it is expected to allow soon the identification of victims from disasters only with his/her biological postmortem samples, being possible to draw a robot portrait and its most likely physical characteristics. In all cases, genetics is the only modern tool with universal character and can be used in essentially all biological samples, giving and identification of more or less accurate statistical character, depending on whether nuclear or lineage markers are used.

Understanding the optimal strategy for a real estate investment and how performance changes based on characteristics is crucial for optimising the achievable return. This is prominent in tourist areas such as Paphos where there is no clear distinction as to whether short or long-term approaches are optimal. The study aimed to develop a model for predicting the optimal rental strategy whilst assessing which model performed best and which property attributes impacted its return the greatest. Short-term data was collected from AirDNA and long-term data was manually collected from real estate agents websites. Furthermore, Random Forest, K-Nearest Neighbour and Multiple Linear Regression models were created to predict the highest and best use for each property. Model accuracy varied between data sets with the best performing model for short-term properties being Random Forest (R-Squared: 0.843), and Distance-Based Multiple Linear Regression for long-term approach (R-Squared: 0.843). The study demonstrated that accurate models could be created to predict the optimal rental strategy with the number of bedrooms being the main driver for rental income, followed by luxury finishes and the presence of a pool. It found that locational characteristics didn’t impact the returns significantly assuming that the property was located within a tourist area.

Tephra plumes can cause a significant hazard for surrounding towns, infrastructure, and air traffic. The current work presents the use of a small and compact X-band Multi-Parameter (X-MP) radar for the remote tephra detection and tracking of two eruptive events at Merapi Volcano, Indonesia, in May and June 2018. Tephra detection was done by analysing the multiple parameters of radar: copolar correlation and reflectivity intensity. These parameters were used to cancel unwanted clutter and retrieve tephra properties, which are grain size and concentration. Real-time spatial and temporal forecasting of tephra dispersal was performed by applying an advection scheme (nowcasting) in the manner of Ensemble Prediction System (EPS). Cross-validation was done using field-survey data, radar observations, and Himawari-8 imagery. The nowcasting model computed both the displacement and growth and decaying rate of the plume based on the temporal changes in two-dimensional movement and tephra concentration, respectively. Our results with ground-based data, where the radar-based estimated grain size distribution fell within the range of in-situ data. The uncertainty of real-time forecasted tephra plume depends on the initial condition, which affects the growth-and decaying rate estimation. The EPS improves the predictability rate by reducing the number of missed and false forecasted events. Our findings and the method presented here are suitable for early warning of tephra fall hazard at the local scale.

In recent years, the individualized demand of customers brings small batches and diversification of orders towards enterprises. The application of enabling technologies in factory, such as the Industrial Internet of Things (IIoT) and Cloud Manufacturing (CMfg), enhances the ability of customer requirement automatic elicitation and the manufacturing process control. The job shop scheduling problem with random job arrival time dramatically increases the difficulty in process management. Thus, how to collaboratively schedule the production and logistics resources in the shop floor is very challenging, and it has a fundamental and practical significance of achieving the competitiveness for an enterprise. To address this issue, the real-time model of production and logistics resources is built firstly. Then, the task entropy model is built based on the task information. Finally, the real-time self-adaption collaboration of production and logistics resources is realized. The proposed algorithm is carried out based on a practical case to evaluate its effectiveness. Experimental results show that our proposed algorithm outperforms three existing algorithms.

Given a stream of depth images with a known cuboid reference object present in the scene, we propose a novel approach for accurate camera tracking and volumetric surface reconstruction in real-time. Our contribution in this paper is threefold: (a) utilizing a priori knowledge of the cuboid reference object, we keep drift-free camera tracking without explicit global optimization; (b) we improve the fineness of the volumetric surface representation by proposing a prediction-corrected data fusion strategy rather than simple moving average, which enables accurate reconstruction of high-frequency details such as sharp edges of objects and geometries of high curvature; (c) we introduce a benchmark dataset CU3D containing both synthetic and real-world scanning sequences with ground-truth camera trajectories and surface models for quantitative evaluation of 3D reconstruction algorithms. We test our algorithm on our dataset and demonstrate its accuracy compared with other state-of-the-art algorithms. We release both our dataset and code as opensource1 for other researchers to reproduce and verify our results.

The practical problem-solving of incidental unreliability of intraoperative neuromonitoring may be the simultaneous neurophysiological recording and the inspection of the surgical field through the camera (the "Real-time neuromonitoring" concept). This would allow the immediate warning of the surgeon on the possibility of the spinal structures insult during but not after the application of the standard procedures in scoliosis surgery (the “Interactive verbal surgeon-neurophysiologist neuromonitoring" concept). This study aimed to compare the advantages, utility, reliability, and time-consuming of both intraoperative neuromonitoring scenarios using non-invasive and innovative recordings from peroneal nerves (PER) versus tibialis anterior muscles (TA) with surface electrodes of motor evoked potentials (MEP) bilaterally as a result of transcranial magnetic (TMS) or electrical (TES) stimulations. Studies were performed in two similar groups ("Real-time neuromonitoring", N=60 and "Interactive verbal sur-geon-neurophysiologist neuromonitoring", N=60) of patients treated surgically because of mainly Lenke 2 type idiopathic scoliosis (IS) pre- (T0), intra- (T1 – before surgical procedures, T2 – after surgical procedures) and postoperatively (T3) as well as in healthy volunteers (N=60, Control). The cumulative parameters of MEP amplitudes and latencies recorded from PER compared to those recorded from TA in healthy volunteers were approximately 67% (1100µV) lower at p=0.007 and 10.6% shorter (3.1 ms) at p=0.04, respectively. A similar trend was also observed in patients from both groups at each follow-up stage. MEP recordings from TA and PER in patients of both groups differed similarly in T0-T3 compared to controls at p=0.008-0.04. MEP parameters in all patients induced by TMS (T0) and TES (T1) did not differ. The parameters of MEP amplitudes recorded from TA and PER intraoperatively in T1 and T2 differed at p=0.04-0.03, indicating the bilateral improvement of neural spinal conduction due to the surgical intervention. Parameters of TMS-induced MEP amplitudes in T3 further increased bilaterally compared to the tests recorded in T0 at p=0.03-0.02. In both groups of patients, an average 51,8 BIS level of anaesthesia minimally affects the variability of the MEP amplitude, especially in PER recordings when ap-plied TES strength was at 98.2 mA. The number of MEP parameter fluctuations, mainly the amplitudes decreasing, was strictly associated with the neurophysiologist's warnings due to transpedicular screws implantation, corrective rods implantation, distraction, derotation, and compression procedures, respectively; at p=0.04-0.03 more in patients from the “Interactive S-N neuromonitoring” group. The average duration of the surgery was significantly shorter (p=0.04) by about 1 hour in the "Real-time neuromonitoring" group. The number of two-way communications between the surgeon and neurophysiologist and vice versa in the "Real-time neuromonitoring" group was reduced by approximately half at p=0.008. The study's results prove the advantages of using the "Real-time neuromonitoring" procedure in increasing safety and non-invasiveness, shortening the time, and lowering the costs of surgical treatment of patients with pathological lateral curvature of the spine. The modifications of the MEP nerve conduction recording technology with surface electrodes from nerves presented in this study enable precise and reliable information on the patient's neurological condition at every stage of applied surgical procedures, even in conditions of slight fluctuations in the anaesthesia.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Polo is an equestrian team sport consisting of four players per team, with level of play determined by cumulative player handicap (-2 to + 10 goals), with a higher handicap denoting a better player. There is minimal literature investigating Polo players’ physical attributes, hence the understanding of the physical characteristics that may contribute to an improved handicap are unknown. This study sought to identify the relationship between pertinent strength measures (left and right hand grip strength; absolute and relative isometric mid-thigh pull) and reaction time in Polo handicap in 19 New Zealand Polo players, and ascertain whether handicap could be predicted by these measures. Correlation coefficients were expressed using R values, accompanying descriptors and 90% confidence intervals (C.I.). Variance explained was expressed via the R2 statistic, and statistical significance set at p < 0.05. Right hand grip strength, isometric mid-thigh pull values were found to significantly correlate to and explain variance within Polo player handicap (all moderate to large correlations; p< 0.05). Whereas left hand grip strength (R: 0.380; 90% C.I. -0.011 to 0.670) and reaction time (0.020; -0.372 to 0.406) were non-significant, moderate and trivial correlates and predictors of handicap respectively. Practically, these findings highlight the differing roles between rein and mallet hands of Polo players and emphasise the importance of a strong and stable platform when riding and striking the ball. Lack of association with reaction time may be explained in part by higher handicapped Polo players employing a more proactive approach to the game.

The genome sequencing of Botrytis cinerea has supplied a general overview of the map of genes involved in secondary metabolite synthesis. B. cinerea genomic data have revealed that this phytopathogenic fungus has seven sesquiterpene cyclase (Bcstc) genes that encode proteins involved in the farnesyl diphosphate cyclization. Three sesquiterpene cyclases (BcStc1, BcStc5 and BcStc7) have been characterized, related to the biosynthesis of botrydial, abscisic acid and (+)-4-epi-eremophilenol, respectively. However, the role of the other four sesquiterpene cyclases (BcStc2, BcStc3, BcStc4 and BcStc6) remains unknown. BcStc3 is a well-conserved protein with homologues in many fungal species, and here, we have undertaken its functional characterization in the life cycle of the fungus. A null mutant ΔBcstc3 and an overexpressed–Bcstc3 transformant (OvBcstc3) were generated, and both strains show deregulation of those other sesquiterpene cyclase-encoding genes (Bcstc1, Bcstc5, Bcstc7). These results suggest a co-regulation of the expression of the sesquiterpene cyclase gene family in B. cinerea. Phenotypic characterization of both transformants revealed that BcStc3 is involved in oxidative stress tolerance, production of reactive oxygen species and virulence. The metabolomic analysis allowed the isolation of characteristic polyketides and eremophilenols from the secondary metabolism of B. cinerea, although no sesquiterpenes different from those already described were identified.

The mechanization of agricultural activities has led to indiscriminate deposition of toxic xenobiotics, including organophosphates in the biomes, and this has led to intoxication characterized with deleterious oxidative and neuronal changes. This study investigated the consequences of oxidative and neurogenic disruptions that follow exposure to two organophosphates, chlorpyrifos (CPF) and dichlorvos (DDVP) on neuro-cognitive performance and anxiety-like behaviors in rats Thirty-two adult male Wistar rats (150 – 170g) were randomly divided into 4 groups, orally exposed to normal saline (NS), DDVP (8.8mg/kg), CPF (14.9mg/kg) and DDVP+CPF for 14 consecutive days. On day 10 of exposures, anxiety-like behaviors and amygdala dependent fear learning were assessed using Open Field and Elevated Plus Maze paradigms respectively, while spatial working memory was assessed on day 14 in the Morris water maze paradigm, following 3 training trials each on days 11, 12 and 13. On day 15, the rats were euthanized, and their brains excised, hippocampus and amygdala removed, 5 of which were homogenized and centrifuged to analyze nitric oxide (NO) metabolites, total reactive oxygen species (ROS), and acetylcholinesterase (AChE) activity, and the other three processed for histology (cresyl violet stain) and proliferative marker (Ki67 immunohistochemistry). Marked (p≤0.05) loss in body weight, AChE depletion, and overproduction of both NO and ROS were observed after repeated exposure to individual and combined doses of CPF and DDVP. Insults from DDVP exposure appeared more severe owing to the observed greater losses in the body weights of exposed rats. There was also a significant (p≤0.05) effect on the cognitive behaviors recorded from the exposed rats, and these deficits were related to the oxidative damage and neurogenic cell loss in the hippocampus and the amygdala of the exposed rats. Taken together, these results provided an insight that oxidative and neurogenic damages are central to the severity of neuro-cognitive dysfunction and increased anxiety-like behaviors that follow organophosphate poisoning.

Real-time object detection remains a pivotal topic in the realm of computer vision. Balancing the accuracy and speed of object detectors poses a formidable challenge for both academic researchers and industry practitioners. While recent transformer-based models have showncase the prowess of the attention mechanism, delivering remarkable performance improvements over CNNs, their computational demands can hinder their effectiveness in real-time detection tasks. In this paper, we elect to use YOLOX as our robust starting point and introduce a series of effective enhancements, culminating in a new high-performance detector named YOLOAX. To further exploit the power of the attention mechanism, we devise multi-dimensional attention-based modules that activate CNNs, emphasizing the most pertinent regions and bolstering the capacity to learn the most informative image representations from feature maps. Moreover, we introduce a novel leading label assignment strategy called STA, along with a groundbreaking loss function named GEIOU Loss, to further refine our detector's performance. We provide extensive ablation studies on the COCO and PASCAL VOC 2012 detection datasets to validate our proposed methods. Remarkably, our YOLOAX is trained solely on the MS-COCO dataset from scratch, without leveraging any prior knowledge, which achieves an impressive 54.2% AP on the COCO 2017 test set while maintaining a real-time speed of 72.3 fps, surpassing YOLOX by a significant margin of 3.0% AP. Our source code and pre-trained models are openly accessible at https://github.com/KejianXu/yoloax.

The detection and analysis of small molecules, typically defined as molecules under 1000 Da, is of growing interest ranging from the development of small molecule drugs and inhibitors to the sensing of toxins and biomarkers. However, due to challenges such as their small size and low mass, many biosensing technologies struggle to have the sensitivity and selectivity for the detection of small molecules. Notably, their small size limits the usage of labeled techniques that can change the properties of small molecule analytes. Furthermore, the capability of real-time detection is highly desired for small molecule biosensors’ application in diagnostics or screening. This review highlights recent advances in label-free real-time biosensing technologies utilizing different types of transducers to meet the growing demand for small molecule detection.

This paper details a design optimization on a hardware accelerator for an on-board real-time SAR imaging system using the Backprojection algorithm, focusing on algorithm-specific approximations intended to reduce the overhead introduced by intensive functions such as the square root, sine, and cosine functions. The main novelty of this work is that new approximations were investigated so that the final image retains high quality regardless of the error in the approximation function. This paper revisits existing approximation methods, such as linear interpolation, polynomial approximation using the Vandermonde matrix, and Chebyshev polynomials, and compares their performance on the algorithm. Results demonstrate that it is possible to maintain the image quality with an SSIM above 0.99 with less 93% LUTs for the square root and less 88% LUTs for the sine and cosine functions using polynomial approximation with the Vandermonde matrix when compared to the HLS baseline functions.

Modern electrical power systems integrate ancillary services to provide security and quality of service in real-time operation because of the intense variations in frequency caused by the massive development and uncertainty of solar-wind generation. Therefore, this ancillary services market focuses on power reserves for secondary and tertiary frequency control. Adjusting reserves and dispatching plants is a manual instruction executed by the system operator to maintain the frequency in the normal operating state (49.80≤f≤50.20 Hz). However, in the absence of an economic model for real-time power reserve reallocation in the ancillary services market, the reserve adjustments made by the system operator are not always optimal since they generate a displacement between the scheduled and actual marginal costs. Then, this work proposes a methodology for operating the ancillary services market in real-time through a dynamic and hourly mathematical model that integrates the variability of solar-wind generation, the demand monitoring curve, and the trajectory of the marginal cost. This model minimizes power reserve costs, which are governed by hourly price auctions, for candidate plants classified as supra/infra-marginal and can optimally reallocate power reserves for secondary and tertiary frequency control.

A reduced order model is developed to monitor aeroengines condition (defining their degradation from a baseline state) in real-time, by using data collected in specific sensors. This reduced model is constructed by applying higher order singular value decomposition plus interpolation to appropriate data, organized in tensor form. Such data are obtained using a detailed engine model that takes the engine physics into account. Thus, the method synergically combines the advantages of data-driven (fast online operation) and model-based (the engine physics is accounted for) condition monitoring methods. Using this reduced order model as surrogate of the engine model, two gradient-like condition monitoring tools are constructed. The first tool is extremely fast and able to precisely compute `on the fly’ the turbine inlet temperature, which is a paramount parameter for the engine performance, operation, and maintenance, and can only be roughly estimated by the engine instrumentation in civil aviation. The second tool is not so fast (but still reasonably inexpensive) and precisely computes both, the engine degradation and the turbine inlet temperature at which sensors data have been acquired. These tools are robust in connection with random noise added to the sensors data and can be straight forwardly applied to other mechanical systems.

The major goal of this paper is to use image enhancement techniques for enhancing and extracting data in FANET applications to improve the efficiency of surveillance. The proposed conceptual system design can improve the likelihood of FANET operations in oil pipeline surveillance, and sports and media coverage with the ultimate goal of providing efficient services to those who are interested. The system architecture model is based on current scientific principles and developing technologies. A FANET, which is capable of gathering image data from video-enabled drones, and an image processing system that permits data collection and analysis are the two primary components of the system. Based on the image processing technique, a proof of concept for efficient data extraction and enhancement in FANET situations and possible services is illustrated

Advanced image processing will be crucial for emerging technologies such as autonomous driving, where the requirement to quickly recognize and classify objects under rapidly changing, poor visibility environments in real time will be needed. Photonic technologies will be key for next-generation signal and information processing, due to their wide bandwidths of 10’s of Terahertz and versatility. Here, we demonstrate broadband real time analog image and video processing with an ultrahigh bandwidth photonic processor that is highly versatile and reconfigurable. It is capable of massively parallel processing over 10,000 video signals simultaneously in real time, performing key functions needed for object recognition, such as edge enhancement and detection. Our system, based on a soliton crystal Kerr optical micro-comb with a 49GHz spacing with >90 wavelengths in the C-band, is highly versatile, performing different functions without changing the physical hardware. These results highlight the potential for photonic processing based on Kerr microcombs for chip-scale fully programmable high-speed real time video processing for next generation technologies.

Layer-wise 3D surface morphology information is critical for the quality monitoring and control of additive manufacturing (AM) processes. However, most of the existing 3D scan technologies are either contact or time consuming, which are not capable of obtaining the 3D surface morphology data in a real-time manner during the process. Therefore, the objective of this study is to achieve real-time 3D surface data acquisition in AM, which is achieved by a supervised deep learning-based image analysis approach. The key idea of this proposed method is to capture the correlation between 2D image and 3D point cloud, and then quantify this relationship by using a deep learning algorithm, namely, convolutional neural network (CNN). To validate the effectiveness and efficiency of the proposed method, both simulation and real-world case studies were performed. The results demonstrate that this method has strong potential to be applied for real-time surface morphology measurement in AM, as well as other advanced manufacturing processes.

For the problem of poor accuracy of the existing multi-rate simulation methods, this paper proposes a multi rate real-time simulation method based on the Norton equivalent, compared with multi-rate simulation method based on the ideal source equivalent. After the Norton equivalence of the fast subsystem and the slow subsystem, they are obtained simultaneously at the junction nodes. In order to reduce the amount of simulation calculation, the Norton equivalent circuit is obtained by incremental calculation. The data interface between the fast subsystem and the slow subsystem is realized by extrapolation method. For ensuring the real-time performance of the simulation, the method that the slow subsystem calculates ahead of the fast subsystem is given for the slow subsystem with a large amount of calculation. Finally, the AC/DC hybrid power system was simulated on the real-time simulation platform (FRTDS), and the simulation results were compared with the single-rate simulation, which verified the correctness and accuracy of the method.

A The agri-food sector is in full renovation, continuously demanding new systems that allow farmers to facilitate their work. Efficient agricultural practices are essential for increasing farm profitability. Efficient agricultural practices can be increased by understanding and managing water neeeds. However, real-time monitoring of water needs is currently slow, and irrigation decisions are based on previous data or physical evidence. Furthermore, the prices of automatic systems for collecting data from several sources (soil and climate) are expensive and the autonomy is very low. Emerging Internet of Things (IoT) technologies such as wireless sensor networks can be used to collect vast amounts of data recorded via apps. By means of an LPWAN communication the farmer can know in real time the state of his crops thanks to a large number of sensors connected wirelessly and distributed across his farm. This paper presents a low consumption solution based on LoRaWAN technology. The wireless sensor node, called BoX, exhibits very low power since it has been optimized both in terms of hardware and software. The result is a higher degree of autonomy than commercial motes. That will allow the farmer to have all the information necessary to achieve an efficient management of his crops with full autonomy.

Real-time strategy (RTS) game has proposed many challenges for AI research for its large state spaces, enormous branch factors, limited decision time and dynamic adversarial environment. To tackle above problems, the method called Adversarial Hierarchical Task Network planning (AHTN) has been proposed and achieves favorable performance. However, the HTN description it used cannot express complex relationships among tasks and impacts of environment on tasks. Moreover, the AHTN cannot handle task failures during plan execution. In this paper, we propose a modified AHTN planning algorithm named AHTNR. The algorithm introduces three elements essential task, phase and exit condition to extend the HTN description. To deal with possible task failures, the AHTNR first uses the extended HTN description to identify failed tasks. And then a novel task repair strategy is proposed based on historical information to maintain the validity of previous plan. Finally, empirical results are presented for the μRTS game, comparing AHTNR to the state-of-the-art search algorithms for RTS games.

The weakness of the dispersion-managed link combined with optical phase conjugation to compensate for optical signal distortion caused by chromatic dispersion and nonlinear Kerr effect of standard single mode fiber is its limited structural flexibility. We propose dispersion map that can simultaneously compensate for the distorted wavelength division multiplexed signal while increasing the configurational flexibility. Each residual dispersion per span (RDPS) in the former half of the proposed link is randomly determined, and in the latter half, the arrangement order of RDPS is the same as or inverted in the former half. We confirm that the dispersion maps in which the RDPS distribution pattern in the latter half is opposite to the arrangement order in the former half are more effective in compensation, and rather, the compensation effect is better than in the dispersion map of the conventional scheme. The notable result of this paper is that the increase of flexibility can be achieved through random arrangement of RDPS in the former half, and the compensation improvement can be achieved by through inverse arrangement in the latter half which make the distribution profile of each half link roughly symmetric with respect to the midway optical phase conjugator.

Analyzing horse behavior is crucial for assessing training quality, particularly in accurately identifying actions like standing, walking, and running. Research has been conducted both domestically and internationally in this regard; however, challenges persist, including reliance on single sensors, poor real-time performance, and low identification accuracy. In view of these challenges, this study investigated real-time identification of horse behavior based on wearable devices. The system, centered around a microcontroller and utilizing a 4G network as a carrier, employs multi-axis IMU sensors as input sources to perceive horse posture. The study proposed a behavior classification method based on analysis of acceleration thresholds. The method consists primarily of two sequential stages: first, the resultant acceleration interval counting method, which employs a nonlinear segmentation approach for initial behavior classification; and second, the statistical analysis of variance parameters between segments, which when coupled with multi-level threshold processing, achieves a refined classification. Experimental results indicated that the interval counting method alone achieved an accuracy of 87.55%, while for the variance analysis method alone the accuracy was 90.87%. The proposed method, comprising the two stages, reached a classification accuracy of 91.57%, underpinning its usefulness in supporting future equine research.

Lithium-ion batteries are key elements in the development of electrical energy storage solutions. However, due to cycling, environmental and operating conditions, battery capacity tends to degrade over time. Capacity fade is a common indicator of battery state of health (SOH) because it is an indication of how capacity has been degraded. However, battery capacity cannot be measured directly, so there is an urgent need to develop methods for estimating battery capacity in real time. By analyzing the historical data of a battery in detail, it is possible to predict the future state of the battery and forecast its remaining useful life. This paper develops a real-time, simple and fast method to estimate the cycle capacity of a battery during the charge cycle using only data from a short period of each charge cycle. This proposal is attractive because it does not require data from the entire charge period, since batteries are rarely charged from zero to full. The proposed method allows simultaneous and accurate real-time prediction of the health and remaining useful life of the battery over its lifetime. The accuracy of the proposed method has been tested using experimental data from several lithium-ion batteries with different cathode chemistries under various test conditions.

Nowadays, the Internet of Things (IoT) concept plays a pivotal role in society and brings new capabilities to different industries. The number IoT solutions in areas such as transportation and healthcare is increasing and new services are under development. In the last decade, society has experienced a drastic increase in IoT connections. In fact, IoT connections will increase in the next few years across different areas. Conversely, despite these benefits, several challenges still need to be faced to enable efficient and secure operations (e.g., interoperability, security, standards, and server technologies). Furthermore, although efforts have been made to produce datasets composed of attacks against IoT devices, several possible attacks are not considered. Most existing efforts do not consider an extensive network topology with real IoT devices. The main goal of this research is to propose a novel and extensive IoT attack dataset to foster the development of security analytics applications in real IoT operations. To accomplish this, 33 attacks are executed in an IoT topology composed of 105 devices. These attacks are classified into seven categories, namely DDoS, DoS, Recon, Web-based, Brute Force, Spoofing, and Mirai. Finally, all attacks are executed by malicious IoT devices targeting other IoT devices.

To elucidate dynamic developmental processes in plants, live tissues and organs have to be visualized frequently and for long time periods. The development of roots is studied in depth at a cellular resolution not only to comprehend the basic processes fundamental to maintenance and pattern formation but also study stress tolerance adaptation in plants. Despite technological advancements, maintaining continuous access to samples and simultaneously preserving their morphological structures and physiological conditions without causing damage presents hindrances in the measurement, visualization and analyses of growing organs including plant roots. We propose a preliminary system which integrates the optical real-time visualization through light microscopy with a liquid culture which enables us to image at the tissue and cellular level horizontally growing Brachypodium roots every few minutes and up to 24 hours. We describe a simple setup which can be used to track the growth of the root as it grows including the root tip growth and osmotic stress dynamics. We demonstrate the system’s capability to scale down the PEG-mediated osmotic stress analysis and collected data on gene expression under osmotic stress.

This study aims to explore the possibility of estimating a multitude of kinematic and dynamic quantities using subject-specific musculoskeletal models in real-time. The framework was designed to operate with marker-based and inertial measurement units enabling extensions far beyond dedicated motion capture laboratories. We present the technical details for calculating the kinematics, generalized forces, muscle forces, joint reaction loads, and predicting ground reaction wrenches during walking. Emphasis was given to reduce computational latency while maintaining accuracy as compared to the offline counterpart. Notably, we highlight the influence of adequate filtering and differentiation under noisy conditions and its importance for consequent dynamic calculations. Real-time estimates of the joint moments, muscle forces, and reaction loads closely resemble OpenSim's offline analyses. Model-based estimation of ground reaction wrenches demonstrates that even a small error can negatively affect other estimated quantities. An application of the developed system is demonstrated in the context of rehabilitation and gait retraining. We expect that such a system will find numerous applications in laboratory settings and outdoor conditions with the advent of predicting or sensing environment interactions. Therefore, we hope that this open-source framework will be a significant milestone for solving this grand challenge.

Ranaviruses have been associated with rising numbers of mass die-offs in amphibian populations globally. With life-stages occupying different environments and presenting distinct physiologies, amphibian of different ages are likely to play an important role in pathogen persistence. To assess the potential role of post-metamorphic amphibians as a Ranavirus reservoir, we performed a bath-exposure study on wood frogs using environmentally relevant doses (~10³ and ~10⁴ PFU/mL) of wild-type (WT) and knockout Frog virus 3 (FV3), deficient for the vIF-2α immune-evasion gene, the effects of which have never been addressed in post-metamorphic anurans. We observed 42% infection prevalence and low mortality (10%) across the virus challenges, with half of the mortalities attributable to ranavirosis. Prevalence and viral loads followed a dose-dependent pattern. Notably, when exposed to the vIF-2α knockout (DvIF-2α) FV3, individuals exhibited significantly decreased growth and increased lethargy in comparison to WT FV3 treatments. Although 85% of individuals in the virus treatments exhibited stereotypic signs of ranavirosis throughout the experiment, at termination (40 days post exposure) most individuals were clear of signs of infection. Overall, this study provides evidence that even a single short time exposure to environmentally relevant doses of Ranavirus may cause sublethal infections in post-metamorphic amphibians, thus indicating their possible role as a reservoir for this pathogen.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

The purpose of the research was to examine and assess the relation between the pilot’s concentration and reaction time with specific brain activity during short-haul flights. In order to obtain this task, participants took part in 1-hour long flight sessions performed on FNPT II class flight simulator. During the flight auto–pilot was activated and subjects were instructed to give response to unexpected events that were occurring during the flight. Brainwaves of each participant were recorded with Emotiv EPOC+ Scientific Contextual EEG device. Statistical analyses of the results were presented in the article.

The last decade was characterized by the reduction of hospital beds throughout Europe. When facing Covid pandemic, this has been an issue of major importance as hospitals were seriously overloaded with an unexpected growth in demand. The dichotomy formed by the scarcity of beds and the need for acute care was handled by the Bed Management (BM) function. This study explores how BM was able to help the solidness of the healthcare system, managing hospital beds at best and recruiting others in different set-tings as intermediate care, in a large Local Health Authority (LHA) in central Italy. Ad-ministrative data show how the provision of appropriate care was achieved recruiting approximately 500 beds belonging to private healthcare facilities affiliated with the re-gional healthcare system and exercising at best the BM function. The ability of the system to absorb the extra demand caused by Covid was made possible using intermediate care beds, which allowed to stretch the logistic boundaries of the hospitals, and by the promptness of Bed Management in converting beds in Covid beds and reconverting them and timely managing internal patient logistic, thus creating space according to the healthcare demand.

The gastrointestinal tract is colonized by trillions of different microorganisms, named the gut microbiota, which is key to degrade undigested food such as dietary fibers. The fermentation of these food components leads to the production of short-chain fatty acids (SCFA) acetate, propionate, and butyrate, which exploit several beneficial roles for the host’s health. Their production and absorption happen in different ways in the human intestine and depend on the type of dietary fiber reaching the gut and the microorganisms involved in the fermentation. The supplementation of SCFAs, mostly butyrate, in treating gastrointestinal, metabolic, cardiovascular, and gut-brain-related diseases has been reported in the medical literature. This review aims to give an overview of the production and absorption dynamics of acetate, propionate, and butyrate in the human gut, with a final focus on the role played by these SCFAs on gastrointestinal and metabolic health and the present therapeutic implications.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

Cultivated adlay or Job’s tear (Coix lacryma-jobi L.) is an important food crop having numerous therapeutic and nutraceutical health benefits. Our study aimed to determine nutrients, minerals, fatty acid composition, and functional groups of seven wild Adlay accessions (brown, black, yellow, grey, green, off-white, and purple) to find out their scope as cereal crops using simple, rapid, and modern analytical techniques. Results revealed variations among bulk densities, specific densities, percent empty spaces, and corresponding grain counts per 10g of sample are valuable characteristics in distinguishing the accessions. Contents of fat, protein, ash, and fibre were found to be comparable to cultivated Adlay. Brown adlay was measured with the highest protein, fat, and fibre contents, 15.82%, 4.76% and 2.37%, respectively. Phosphorus, potassium, calcium, and sodium ranged 0.3% - 2.2%, whereas boron, iron, copper, zinc, and manganese were in the range 1.6mg/kg - 20.8mg/kg. Wild adlay triglyceride composition constituted of polyunsaturated fatty acids as primary fraction followed by olein and palmitic acid as prominent fatty acids. Distinguishing functional groups expressed infra-red frequencies in narrow bands and fingerprint region of proteins associated with out-of-plane region evident structural differences among adlay accessions. Frequency of functional groups in seven accessions indicated black genotype promising for varietal development.

In the last decades we have experienced great social, cultural, and educational changes, spending more time performing tasks in near vision and less hours in outdoor activities, having more overexposure to digital screens, especially the youngest and increasingly from younger ages. It is common to see cases when performing tasks in near vision the posture or position of the head is not adequate, especially the youngest, being essential to have a correct posture of the head to avoid visual, muscular, or articular problems. We present a procedure to try to control the correct position of the head in real time when performing close-up activities. The aim is to detect the inclination of the head and to know if a bad position is adopted due to a visual problem or simply to inadequate visio-postural habits, warning us of the postural anomaly to correct it.

The flow properties of pellets or granules are crucial for further processing the drug dosage forms. Optimal compression or filling the multiparticulate dosage forms into capsules is influenced by forces between discrete particles, which could be partially characterized by flow properties. Several techniques were developed for the examination of flowability, including static and dynamic methods applying empirical studies and the up-to-date chaos theory; however newest methods seem only to be powerful with the supplement of empirical principles. Our experiments try to refine both the technique of analysis and the methods by finding new, alternative ways. Our approach to the flowability measurements was to set up a dynamic time-dependent model which combines empirical observations and the chaos theory on a geometrical basis, thus find new aspects regarding flow properties of pellets and granules that could be relevant for drug developers.

This study presents a novel approach to enhance Large Language Models (LLMs) like Alpaca by dynamically integrating real-time information. This method addresses the issue of content hallucination and data relevancy by automatically collecting and integrating current data from credible sources into model prompts. Experiments show a significant improvement in accuracy and a decrease in content hallucination, with a manageable increase in response time. The research underscores the potential of real-time data integration in making LLMs more accurate and contextually relevant, setting a foundation for future advancements in dynamic data processing in AI.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

Rapid growth of IoT applications and their interference in our daily lives led to many different IoT devices which generates enormous data. The IoT devices’ resources are very limited, so storing and processing IoT data in the devices is very inefficient. Several resources of cloud-computing are efficiently used to handle some IoT resources issues. While using resources in the cloud centers cause some other issues, like latency in the IoT applications, which are time-critical. Thus, the technology of edge cloud has evolved recently. This technology permits storage and data processing at the network edge. This paper studies edge computing in-depth for timeless sensitive devices in IoT. In-depth, cutting-edge IoT computing systems (ECAs-IoT) are evaluated and characterized in this paper according to numerous criteria, such as information placement, improvisation facilities, reliability, and data visualization. Moreover, according to distinctive properties, the paper aims at comparing each structure in detail. The paper also highlights the significant limitations of the new ECAs-IoT and recommends solutions to them. The studies also introduce and propose solutions to some of the most important restrictions of the current ECAs-IoT. Consequently, in the edge computing domain, this survey outlines the IoT implementations. Lastly, with the use of IoT implementations for ECAs-IoT, the paper suggests four distinct scenarios.

Recent developments in mid-infrared (MIR) spectroscopic ellipsometry enabled by quantum cascade lasers (QCLs) resulted in a drastic improvement in signal-to-noise ratio compared to conventional thermal emitter based instrumentation. Thus, it was possible to reduce the acquisition time for high-resolution broadband ellipsometric spectra from multiple hours to less than 1 second. This opens up new possibilities for real-time in-situ ellipsometry in polymer processing. To highlight these evolving capabilities we demonstrate the benefits of a QCL based MIR ellipsometer by investigating single and multilayered polymer films. The molecular structure and reorientation of a 2.5m thin biaxially oriented polyethylene terephtalate film is monitored during a stretching process lasting 24.5 s to illustrate the perspective of ellipsometric measurements in dynamic processes. In addition, a polyethylene/ethylene vinyl alcohol/polyethylene multilayer film is investigated at continuously varying angle of incidence ( 0∘ – 50∘) in 17.2 s, highlighting an unprecedented sample throughput for the technique of varying angle spectroscopic ellipsometry in the MIR spectral range. The obtained results underline the superior spectral and temporal resolution of QCL ellipsometry and qualify this technique as suitable method for advanced in-situ monitoring in polymer processing.

Human exposure to infectious aerosols results a transmission of diseases, such as influenza, tuberculosis, and COVID-19. Most dental procedures generate a significant number of aerosolized particles, increasing transmission risk in dental settings. Since the generation of aerosols in dentistry is unavoidable, many clinics started using intervention strategies such as area-filtration units and extraoral evacuation equipment, especially under the relatively recent constraints of the pandemics. However, the effectiveness of these devices in dental operatories has not been studied. Therefore, the dental personnel's ability to position and operate such instruments efficiently is also limited. To address these challenges, we utilized a real-time sensor network for assessment of aerosol dynamics during dental restoration and cleaning producers with and without intervention. The strategies tested during the procedures were (i) local area high-efficiency particle air (HEPA) filters and (ii) extra-oral suction device (EOSD). The study was conducted at the University of Washington School of Dentistry using a network of thirteen fixed sensors positioned within the operatory and one wearable sensor worn by the dental operator. The sensor network provides time and space-resolved particulate matter (PM) data. Three-dimensional (3D) visualization informs aerosol persistence in the operatory. It was found that area filters did not improve the overall aerosol concentration in dental offices significantly. An average of 16% decrease in PM concentration was observed when EOSD equipment was used during the procedures. The combination of real-time sensors and 3D visualization can provide dental personnel and facility mangers with actionable feedback to effectively assess aerosol transmission in medical settings and develop evidence-based intervention strategies.

With the development of designing and manufacturing level for micro-electromechanical system (MEMS) gyroscopes, the control circuit system becomes a key point to determine their internal performances. Nevertheless, phase delay of electron components may result in some serious hazards. This paper describes a real-time circuit phase delay correction system for MEMS vibratory gyroscopes. A detailed theoretical analysis is provided to clarify the influences of circuit phase delay on the in-phase and quadrature (IQ) coupling characteristics and zero rate output (ZRO) utilizing force-to-rebalance (FTR) closed-loop detection and quadrature correction system. By deducing the relationship between amplitude-frequency, phase-frequency of MEMS gyroscope and the phase relationship of the whole control loop, a real-time correction system is proposed to automatically adjust the phase reference value of phase-locked loop (PLL) and thus compensate for the real-time circuit phase delay. The experimental results show that the correction system can accurately measure and compensate the circuit phase delay in real time. Furthermore, the unwanted IQ coupling can be eliminated and the ZRO is decreased by 755% to 0.095°/s. This correction system realizes a small angle random walk of 0.978°/√h, and a low bias instability of 9.458°/h together with a scale factor nonlinearity of 255 ppm at room temperature. Besides, the thermal drift of ZRO is reduced to 0.0034°/s/°C at a temperature range from -20°C to 70°C.

Real-time energy management of a converter-based microgrid is difficult to determine optimal operating points of a storage system in order to save costs and minimise energy waste. This complexity arises due to time-varying electricity prices, stochastic energy sources and power demand. Many countries have imposed real-time electricity pricing to efficiently control demand side management. This paper presents a particle swarm optimisation (PSO) for the application of real-time energy management to find optimal battery controls of a community microgrid. The modification of the PSO consists in altering the cost function to better model the battery charging/discharging operations. As optimal control is performed by formulating a cost function, it is suitably analysed and then a dynamic penalty function in order to obtain the best cost function is proposed. Several case studies with different scenarios are conducted to determine the effectiveness of the proposed cost function. The proposed cost function can reduce operational cost by 12% as compared to the original cost function over a time horizon of 96 hours. Simulation results reveal the suitability of applying the regularised PSO algorithm with the proposed cost function, which can be adjusted according to the need of the community, for real-time energy management.

Software-based ultrasound imaging systems provide high flexibility that allows easy and fast adoption of newly developed algorithms. However, the extremely high data rate required for data transfer from sensors (e.g., transducers) to the ultrasound imaging systems is a major bottleneck in the software-based architecture, especially in the context of real-time imaging. To overcome this limitation, in this paper, we present a Binary cLuster (BL) code, which yields an improved compression ratio compared to the exponential Golomb code. Owing to the real-time encoding/decoding features without overheads, the universal code is a good solution to reduce the data transfer rate for software-based ultrasound imaging. The performance of the proposed method was evaluated using in vitro and in vivo data sets. It was demonstrated that the BL-beta code has a good stable lossless compression performance of 20 ~ 30% while requiring no auxiliary memory or storage.

Alkali Silica Reaction (ASR) is known to be a serious problem for concrete worldwide, especially in high humidity and high temperature regions. ASR is a slow process that develops over years to decades and it is influenced by changes in environmental and loading conditions of the structure. The problem becomes even more complicated if one recognizes that other phenomena like creep and shrinkage are coupled with ASR. This results in synergistic mechanisms that can not be easily understood without a comprehensive computational model. In this paper, coupling between creep, shrinkage and ASR is modeled within the Lattice Discrete Particle Model (LDPM) framework. In order to achieve this, a multi-physics formulation is used to compute the evolution of temperature, humidity, cement hydration, and ASR in both space and time, which is then used within physics-based formulations of cracking, creep and shrinkage. The overall model is calibrated and validated on the basis of experimental data available in the literature. Results show that even during free expansions (zero macroscopic stress), a significant degree of coupling exists because ASR induced expansions are relaxed by meso-scale creep driven by self-equilibriated stresses at the meso-scale. This explains and highlights the importance of considering ASR and other time dependent aging and deterioration phenomena at an appropriate length scale in coupled modeling approaches.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

The confinement experienced due to the COVID-19 pandemic has prompted a rethink of the teaching-learning process to which teachers have responded without planning and instead using their resources. This study aims to analyze the relationships between work-family interactions, technostress, and perceived organizational support in teachers during the confinement period in Spain that began in March 2020. An online survey was administered to 640 pre-school, primary, and secondary school teachers. Positive reciprocal work-family interactions and their relationship with organizational support were found, with differences according to gender, with women showing a more negative perception of the impact on the family. There were no marked levels of technostress in the overall sample, although higher levels of perceived ineffectiveness and skepticism were found in teachers aged 46 years or older. Teachers in private and subsidized schools showed a higher level of perceived support than those in public schools. There is a need to continue this work to verify the values of these dimensions in other contexts and to apply institutional measures and public policies to improve these indicators in this group.

Anti-diabetic effects of Glycine soja seed extract (GS) on Type 2 diabetes mellitus mouse model and human hepatocytes induced insulin resistance were investigated. 3 weeks old db/db mice were divided into 5 groups (n = 6) including two control groups and 3 GS treated groups with different doses. Oral administration of GS for 6 weeks to diabetic db/db mice reduced blood glucose level significantly in a dose dependent manner by 44.7% (300 mg/kg/day), 30.9% (150 mg/kg/day) and 21.1% (75 mg/kg/day). GS treatment also lowered significantly plasma level of HbA1c, insulin, IGF-1 and leptin, and increased that of adiponectin. GS treatment activated AMPK, and down-regulated GLUT2 in liver tissues of mice while up-regulated GLUT4 in muscle tissues of mice. In in vitro study with insulin resistance induced human hepatocyte, GS treatment increased glucose uptake and increased the activities of Akt and PPAR-γ in response to insulin. Treatment of GS appears to reduce blood glucose level by regulating energy metabolism positively through various metabolic pathways and reducing insulin resistance in Type 2 diabetes mellitus.

Anti-diabetic effects of Glycine soja seed extract (GS) on Type 2 diabetes mellitus mouse model and human hepatocytes induced insulin resistance were investigated. 3 weeks old db/db mice were divided into 5 groups (n = 6) including two control groups and 3 GS treated groups with different doses. Oral administration of GS for 6 weeks to diabetic db/db mice reduced blood glucose level significantly in a dose dependent manner by 44.7% (300 mg/kg/day), 30.9% (150 mg/kg/day) and 21.1% (75 mg/kg/day). GS treatment also lowered significantly plasma level of HbA1c, insulin, IGF-1 and leptin, and increased that of adiponectin. GS treatment activated AMPK, and down-regulated GLUT2 in liver tissues of mice while up-regulated GLUT4 in muscle tissues of mice. In in vitro study with insulin resistance induced human hepatocyte, GS treatment increased glucose uptake and increased the activities of Akt and PPAR-γ in response to insulin. Treatment of GS appears to reduce blood glucose level by regulating energy metabolism positively through various metabolic pathways and reducing insulin resistance in Type 2 diabetes mellitus.

Today, mechanical tracking systems have been downsized to allow them to be used in the field of airborne laser communications and in the military domain. Risley systems are used for this purpose, which work by directing a beam of light to a given target point, this procedure is commonly known as the inverse problem. In this paper, an analytical method, the geometric method, has been designed and developed to determine the beam steering in a Risley system and solve the inverse problem. The method focuses on different geometric shapes, like circumference or ellipse, that are described when the beam passes through the second prism. The accuracy and efficiency of the geometric method has been analysed and found to be faster than the two-step method. Furthermore, the geometric method has been implemented in an iterative process and an accuracy of up to 1 pm has been achieved. This high accuracy would allow the geometric method to be applied in fields such as lithography, stereolithography or 3D printers.

Real-time data processing and decision-making are increasingly crucial in various applications, driven by the continuous influx of data streams. Event-driven AI workflows within serverless computing environments offer a promising approach to handle these real-time demands efficiently. This paper presents a framework for simulating and analyzing the performance characteristics of such workflows. Our proposed approach utilizes simulated data with varying event rates and durations to investigate the impact on key performance metrics like latency, throughput, and resource utilization. This enables a comprehensive evaluation of the inherent trade-offs within event-driven AI systems. The key findings reveal a trade-off between latency and throughput. As the event rate increases, average processing latency generally increases while average throughput increases. Resource utilization remains relatively stable across different event rates in the simulated scenarios (e.g., 75.55\% at 2 events/second, 74.51\% at 10 events/second). This framework provides a valuable tool for understanding the performance characteristics of event-driven AI workflows and optimizing resource allocation strategies.

Traffic congestion is a persistent and challenging problem in urban areas, leading to increased travel times, fuel consumption, and environmental pollution. Signalized intersections play a pivotal role in regulating traffic flow, and their efficiency has a direct impact on the overall traffic performance of a city. This study investigates the effect of traffic signal in managing traffic volume and reducing congestion and delays at signalized intersections through a comprehensive analysis of existing research, data collection, and simulations.The research begins by analyzing the traffic characteristics by an installed LiDAR sensor at E Cold Spring Ln – Hillen Rd intersection in Baltimore City, MD. When the signal at this intersection stopped working for some hours during a working day in September 2023, the LiDAR recorded vehicle and pedestrian counts, vehicle-vehicle and vehicle-pedestrian conflicts, and jaywalking events conflicts. The research aims to assess the impact of traffic signal failures on traffic flow, congestion, safety (V2V and V2P conflicts), and the frequency of jaywalking events before, during, and after improper performance of the traffic signal. Furthermore, this study explores the factors influencing traffic signal performance, including traffic demand, geometric layout, pedestrian interactions, and the integration of emerging technologies. The analysis results highlighted the importance of signal control systems existence at this intersection that can adjust signal timing in response to changing the real-time traffic conditions.Reduced congestion, minimized delays, and enhanced traffic flow are observed outcomes, contributing to a more sustainable and efficient urban transportation system. However, it is crucial to consider the trade-offs and challenges associated with traffic signal optimization, such as the potential for increased travel times for certain modes of transportation and the need for ongoing maintenance and updates. In conclusion, this study underscores the pivotal role of traffic signals in managing traffic volume and reducing congestion and delays at signalized intersections. Through evidence-based analysis and innovative signal control strategies, urban planners and transportation authorities can work towards creating more efficient, sustainable, and less congested transportation networks. The insights derived from this research can inform policy decisions and guide the development of future traffic management solutions, ultimately leading to improved quality of life in urban areas.

Air quality and environmental fairness have always been an area of prime interest across the globe. The significance low-cost air quality sensing and practices spikes during the time of pan-demic and epidemics when the air becomes a threat to living beings especially human beings. The gradual innovation and enrichment in low-cost air quality sensing sensors, nodes or devices, and systems are exponentially increasing for the last three decades. This work reviews the major contributions in a) low-cost scalable air quality assessment; b) low-cost air quality sensors, sensing approaches and technologies; c) low-cost state-of-the-art gas sensors fabrication methods (MEMS and CMOS); d) low-cost gas sensors measurement configurations and assemblies; and e) low-cost air quality sensors calibration and testing systems. A systematic review of past work with a goal to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies has been rendered in this work. Starting from sensors electrodes to IoT based mobile smart nodes; all have been introduced in this article.

Remotely Piloted Aircraft Systems (RPAS) are increasingly becoming relevant actors flying through the airspace and will assume much more importance in the future perspective. In order to allow their safe integration with manned conventional traffic in non-segregated airspaces, in accordance with the overall Air Traffic Management (ATM) paradigm, specific enabling technologies are needed. As well known, among the enabling technologies identified as crucial for RPAS integration into the overall ATM system, the Detect and Avoid (DAA) technology is fundamental. In the meantime, to support extended surveillance, the universal introduction on-board of aircraft of cooperative Automatic Dependent Surveillance – Broadcast (ADS-B) is increasingly implemented, having the potential to allow coverage of the whole airspace also in remote areas not usually covered by conventional radar surveillance. In this paper, the experimental results are presented and discussed that have been obtained through the real-time validation, with hardware and human in the loop (RTS-HIL) simulations, of an automatic ADS-B based Separation Assurance and Collision Avoidance System aimed to support RPAS automatic operations as well as remote pilot decision making. In the paper, after an introductory outline of the Concept of Operations (ConOps) of the system and of its architectural organization, while also providing basic information about the main system functionalities, the description is reported of the tests that have been carried out and the obtained results are described and discussed, in order to emphasize the performances and limitations of the proposed system. In particular, not only the quantitative performances obtained are reported and commented but also the feedbacks received by the pilots in order to improve the system are described, for instance in terms of preferred typology of conflict resolution manoeuver elaborated by the system.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

Given the high number of vehicle-crash victims, it has been established as a priority to reduce this figure in the transportation sector. For this reason, many of the recent researches are focused on including control systems in existing vehicles, to improve their stability, comfort and handling. These systems need to know in every moment the behavior of the vehicle (state variables), among others, when the different maneuvers are performed, to actuate by means of the systems in the vehicle (brakes, steering, suspension) and, in this way, to achieve a good behavior. The main problem arises from the lack of ability to directly capture several required dynamic vehicle variables, such as roll angle, from low-cost sensors. Previous studies demonstrate that low-cost sensors can provide data in real-time with the required precision and reliability. Even more, other research works indicate that neural networks are efficient mechanisms to estimate roll angle. Nevertheless, it is necessary to assess that the fusion of data coming from low-cost devices and estimations provided by neural networks can fulfill the reliability and appropriateness requirements for using these technologies to improve overall safety in production vehicles. Because of the increasing of computing power, the reduction of consumption and electric devices size, along with the high variety of communication technologies and networking protocols using Internet have yield to Internet of Things (IoT) development. In order to address this issue, this study has two main goals: 1) Determine the appropriateness and performance of neural networks embedded in low-cost sensors kits to estimate roll angle required to evaluate rollover risk situations. 2) Compare the low-cost control unit devices (Intel Edison and Raspberry Pi 3 Model B), to provide the roll angle estimation with this artificial neural network-based approach. To fulfil these objectives an experimental environment has been set up composed of a van with two set of low-cost kits, one including a Raspberry Pi 3 Model B, low cost Inertial Measurement Unit (BNO055 - 37€) and GPS (Mtk3339 - 53€) and the other having an Intel Edison System on Chip linked to a SparkFun 9 Degrees of Freedom module. This experimental environment will be tested in different maneuvers for comparison purposes. Neural networks embedded in low-cost sensor kits provide roll angle estimations very approximated to real values. Even more, Intel Edison and Raspberry Pi 3 Model B have enough computing capabilities to successfully run roll angle estimation based on neural networks to determine rollover risks situation fulfilling real-time operation restrictions stated for this problem.

In this paper, Lyapunov-Razumikhin technique, design of state-dependent switching laws, a fixed point theorem and variational methods are employed to derive the existence and the unique existence results of (globally) exponentially stable positive stationary solution of delayed reaction-diffusion cell neural networks under Dirichlet zero boundary value, including the global stability criteria \textbf{in the classical meaning}. Next, sufficient conditions are proposed to guarantee the global stability invariance of ordinary differential systems under the influence of diffusions. New theorems show that the diffusion is a double-edged sword in judging the stability of diffusion systems. Besides, an example is constructed to illuminate that any non-zero constant equilibrium point must be not in the phase plane of dynamic system under Dirichlet zero boundary value, or it must lead to a contradiction. Next, under Lipschitz assumptions on active function, another example is designed to prove that the small diffusion effect will cause the essential change of the phase plane structure of the dynamic behavior of the delayed neural networks via a Saddle point theorem. Finally, a numerical example illustrates the feasibility of the proposed methods.

Reactions of picolinamides with 1,3-propanesultone in methanol followed by the treatment with ketones led to a series of previously unknown chemical transformations, yielding first pyridinium salts (2a-f) with a protonated endocyclic nitrogen atom and then heterocyclic salts (3a-j) containing a 4-imidazoline ring. The structures of intermediate and final products were determined by IR and 1H, 13C NMR spectroscopy and X-ray study. The effects of the ketone and alcohol structures on the product yield were studied by quantum-chemical calculations. The stability of salts 3a-j towards hydrolysis and alcoholysis makes them excellent candidates for the search of new types of biologically active compounds.

French Guiana, located in the Guiana Shield, is a natural reservoir for many zoonotic pathogens that are of considerable medical or veterinary importance. Until now, there are few data available on the description of parasites circulating in this area, especially on protozoan belonging to the phy-lum Apicomplexa; conversely, the neighbouring countries describe a high parasitic prevalence in animals and humans. Epidemiological surveillance is necessary, as new potentially virulent strains may emerge from these forest ecosystems, such as Amazonian toxoplasmosis. However, there is no standard tool for detecting protozoa in wildlife. In this study, we developed Meat-Borne-Parasite, a high-throughput meta-barcoding workflow for detecting Apicomplexa based on Oxford Nanopore Technologies sequencing platform using the 18S gene of fourteen Apicomplexa-positive samples collected in French Guiana. Sequencing reads were then analysed with MetONTIIME pipeline. Thanks to a scoring rule, we were able to classify as Apicom-plexa-positive 10 samples out of 14 and reveal the presence of co-carriages. The same samples were also sequenced with Illumina platform, for validation purposes. On samples identified as Apicomplexa-positive by both platforms, a strong positive correlation at up to genus level was reported. Overall, the presented workflow represents a reliable method for Apicomplexa detec-tion, which may pave the way for more comprehensive biomonitoring of zoonotic pathogens.

The involvement of the angiotensin II type 1 receptor in the Frank-Starling Law of the Heart, where the various activations are very limited, allows simple analysis of the kinase systems involved and thence extrapolation of the mechanism to that of angiotensin control of activation of cardiac and skeletal muscle contraction. The involvement of phosphorylation of the myosin light chain in the control of contraction is accepted but not fully understood. The involvement of troponin-I phosphorylation is also indicated but of unknown mechanism. There is no known signal for activation of myosin light chain kinase or Protein Kinase C-βII other than Ca²⁺/calmodulin but the former is constitutively active and thus has to be under control of a regulated inhibitor, the latter kinase may also be the same. Ca²⁺/calmodulin is not activated in Frank-Starling, i.e. there are no diastolic or systolic [Ca²⁺] changes. I suggest here that that the regulated inhibition is by myosin light chain phosphatase and/or β-arrestin. Angiotensin activation is by translocation of the β-arrestin from the sarcoplasm to the PM thus reducing its kinase inhibition action in the sarcoplasm, this reduced inhibition has been wrongly attributed to a mythical downstream agonist property of β-arrestin.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

Breaking up prolonged sitting by short bouts of light physical activities including standing and walking has been shown to be beneficial for people with type 2 diabetes (T2D). This paper presents the development of an android mobile app to deliver a just-in-time adaptive intervention (JITAI) to reduce sedentary time in people with T2D. A total of six design workshops were conducted with seven experts to identify design requirements, a behavioural framework, and required contextual adaptations for the development of a bespoke mobile app (iMOVE). Moreover, a focus group was conducted among people with T2D as potential end-users (N=10) to ascertain their perceptions of the app. Feedback from the focus group was used in subsequent iterations of the iMOVE app. Data were analysed using an inductive qualitative thematic analysis. Based on workshops, key features of iMOVE were developed, including simplicity (e.g., navigation, login), colours and font sizes, push notifications, messaging algorithms and a triggering system for breaking up sitting time and moving more. Based on the user testing results, a goal setting tab was added, font sizes were made larger, the brightness of colours was reduced, and a colour indicator was used to indicate device connectivity with an activity tracker. A user-centric app was developed to support people with T2D to transition from sedentary to active lifestyles.

Wounding is a serious environmental stress in plants. Oxylipins such as jasmonic acid play an important role in defense against wounding. Mechanisms to adapt to wounding have been investigated in vascular plants; however, those mechanisms in nonvascular plants remain elusive. To examine the response to wounding in Physcomitrella patens, a model moss, a proteomic analysis of wounded P. patens was conducted. Proteomic analysis showed that wounding increased the abundance of proteins related to protein synthesis, amino acid metabolism, protein folding, photosystem, glycolysis, and energy synthesis. 12-Oxo-phytodienoic acid (OPDA) was induced by wounding and inhibited growth. Therefore, OPDA is considered a signaling molecule in this plant. Proteomic analysis of a P. patens mutant in which the PpAOS1 and PpAOS2 genes, which are involved in OPDA biosynthesis, are disrupted showed accumulation of proteins involved in protein synthesis in response to wounding in a similar way to the wild-type plant. In contrast, the fold-changes of the proteins in the wild-type plant were significantly different from those in the aos mutant. This study suggests that PpAOS gene expression enhances photosynthesis and effective energy utilization in response to wounding in P. patens.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

We conducted a pilot study to analyze the differential methylation status of 20 primary acinar adenocarcinomas of the lungs. These adenocarcinomas had to be wild type in mutation analysis and had either high (TPS&gt;50%; n=10) or low (TPS&lt;1%; n=10) PD-L1 status to be integrated into our study. To examine the methylation of 866,895 specific sites, we utilized the Illumina Infinium EPIC bead chip array. Both hypermethylation and hypomethylation play significant roles in tumor development, progression, and metastasis. They also impact the formation of the tumor microenvironment, which plays a decisive role in tumor differentiation, epigenetics, dissemination, and immune evasion. The gained methylation patterns were correlated with PD-L1 expression. Our analysis has identified distinct methylation patterns in lung adenocarcinomas with high and low PD-L1 expression. After analyzing the correlation between methylation results of genes and promoters with their pathobiology, we found that tumors with high expression of PD-L1 tend to exhibit oncogenic effects through hypermethylation. On the other hand, tumors with low PD-L1 expression show loss of their suppressor functions through hypomethylation. The suppressor functions of hypermethylated genes and promoters are ineffective compared to simultaneously activated dominant oncogenic mechanisms. The tumor microenvironment supports tumor growth in both groups.

In T. gondii, as well as in other model organisms, gene knock-out using CRISPR-Cas9 is a suitable tool to identify the role of specific genes. The general consensus implies that only the gene of interest is affected by the knock-out. Is this really the case? In a previous study, we have generated knock-out (KO) clones of TgRH88_077450 (SRS29B; SAG1) which differed in the numbers of integrated dihydrofolate-reductase-thymidylate-synthase (MDHFR-TS) drug-selectable marker. Clones 18 and 33 had a single insertion of MDHFR-TS within SRS29B. Clone 6 was disrupted by the insertion of a short unrelated DNA-sequence, but the marker was integrated elsewhere. In clone 30, the marker was inserted into SRS29B and several other MDHFR-TS copies were found in the genome. KO and wild-type (WT) tachyzoites had similar shape, dimensions and vitality. This prompted us to investigate the impact of the genetic engineering as such on the overall proteome patterns of the four clones as compared to the respective WT. Comparative shotgun proteomics of the five strains was performed. Overall, 3236 proteins were identified. Principal component analysis of the proteomes revealed five distinct clusters corresponding to the five strains by both iTop3 and iLFQ algorithms. Detailed analysis of the differentially expressed proteins revealed that the target of the KO, srs29B, was lacking in all KO clones. Besides this protein, twenty other proteins were differentially expressed between KO clones and WT or between different KO clones. The protein exhibiting the highest variation between the five strains was srs36D encoded by TgRH_016110. The deregulated expression of SRS36D was further validated by quantitative PCR. Moreover, the transcript levels of three other selected SRS genes, namely SRS36B, SRS46, and SRS57 exhibited significant differences between individual strains. These results indicate that knocking out a given gene may affect the expression of other genes. Therefore, care must be taken when specific phenotypes are regarded as a direct consequence of the KO of a given gene.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Diffuse correlation spectroscopy (DCS) is a non-invasive technology for the evaluation of the blood perfusion in deep tissue. However, it requires high computational resources for data analysis which poses challenges in its implementation for real-time applications. To address the unmet need, we developed a novel device-on-chip solution that fully integrates all the necessary computational components needed for DCS. It takes the output of a photon detector and determines the blood flow index (BFI). It is implemented on a Field Programmable Gate Array (FPGA) chip including a multi-tau correlator for the calculation of the temporal light intensity autocorrelation function and a DCS analyzer to perform the curve fitting operation that derives the BFI. The FPGA DCS system was evaluated against a lab-standard DCS system for both phantom and cuff-ischemia studies. The results indicate that the autocorrelation of the light correlation and BFI from both the FPGA DCS and the reference DCS matched well. Furthermore, the FPGA DCS system was able to achieve a measurement rate of 50 Hz and resolve pulsatile blood flow.

The most commonly used real-time augmentation services in China are International GNSS Service (IGS) real-time service, PPP-B2b service, and BeiDou Satellite-Based Augmentation System (BDSBAS) dual-frequency augmentation service. However, the research on the performance evaluation, comparison and application scope of these three products is still unknown and unrevealed. This article introduces methods for obtaining real-time augmentation information and real-time orbit and clock offset recovery. Based on real-time orbit and clock offset accuracy, positioning accuracy, and positioning availability, it systematically evaluates the performance of CNES, PPP-B2b, and BDSBAS augmentation information. The results indicate that the radial accuracy of CNES and PPP-B2b real-time orbit products is consistent, and the Root Mean Square (RMS) is better than 5 cm. CNES can achieve centimeter-level accuracy in both along-track and cross-track components, surpassing the decimeter-level accuracy of PPP-B2b. Both services demonstrate consistent accuracy in real-time clock offset, with PPP-B2b showing similar standard deviations (STD) of 0.16 ns for different satellites. However, for CNES, the STD of real-time clock offset varies for GPS, BDS-3 MEO, and BDS-3 IGSO satellites, with values of 0.10 ns, 0.19 ns, and 0.60 ns, respectively. The accuracy and availability of the two PPP services exhibit the same levels, with centimeter-level accuracy achieved after convergence and positioning availability exceeding 99%. Therefore, the difference between the two services in application areas depends on the acquisition of augmentation information. However, BDSBAS, which concentrates on code observations, demonstrates lower accuracy in real-time orbit and clock offset, positioning accuracy, and positioning availability compared to the other two services. Its primary application is in the aviation and maritime domains, where there is a greater need for service integrity, continuity, and reliability.

Currently, a wide variety of velocity profiles are used in motion control. Thus, this paper compares the energy consumption of three parabolic, trapezoidal, and S-curve profiles. We studied the case of using embedded systems since they are a powerful solution to monitor and coordinate the movement of devices and machinery in various industries combined with motion control applications. These integrated systems allow precise and efficient control of motors and actuators through control and feedback algorithms. In addition, we propose an alternative methodology for implementing motion controllers using an Advanced RISC Machine (ARM) microcontroller, which computes the trajectory and the control action in real-time. We conducted an experiment using a linear plant composed of a direct current (DC) motor coupled to an endless screw where a carriage is mounted that can move mechanically along a rail a distance of 1.16m. In addition, a 4096 pulses per revolution (PPR) encoder is connected to the motor to measure position and angular velocity, which compute the distance the carriage has moved in meters. A current sensor is used to assess the energy consumption, and 40 tests for each profile were carried out to compare the energy consumption for the three-motion profiles considering cases with and without load on the carriage.

Smart flexible materials with piezoresistive property are increasingly used in sensors field. When embedded in structures, they would allow an in-situ structural health monitoring and damage assessment of impact loading such as crash, bird strikes and ballistic impacts. However, this could not be achieved without a deep characterization of the relation between piezoresistivity and mechanical behavior. The aim of this paper is to study the potential use of the piezoresistivity effect of a conductive foam made of a flexible polyurethane matrix filled with active carbon for integrated Structural Health Monitoring (SHM) and damage assessment applications. To do so, PolyUrethane Foam filled with Active Carbon, namely PUF-AC, are manufactured and tested under quasi-static compression tests and under Dynamic Mechanical Analyser (DMA) with in-situ measurement of its resistivity during tests. A relation is proposed for describing the evolution of the resistivity versus strain and stress. In addition, a demonstrative experiment of a PUF-AC sample subjected to low velocity impact assesses the interest of this type of materials for damage assessments.

When a rotary machine is running, from which the acquired vibro-acoustic signals enable to reveal its operation status and health condition. The study proposed a DSP-based adaptive angular-velocity Vold-Kalman filtering order tracking (AV2KF_OT) algorithm with an online real-time nature for signal interpretation and machine condition monitoring. Theoretical derivation and numerical implementation of computation schemes are briefly introduced. An online real-time monitoring system based on the AV2KF_OT algorithm, which was implemented through both a digital signal processor and a user interface coded by using LabVIEW, was developed. Two experimental tasks were applied to justify the proposed technique, including (i) the detection of startup on the fluid-induced whirl performed through a journal-bearing rotor rig, and (ii) the separation of close orders from the measured signals of a multifunction transmission-element ball-bearing bench.

Remanufacturing is a viable option to extend the useful life of an end-of-use product or its parts, ensuring sustainable competitive advantages under the current global economic climate. Challenges typical to remanufacturing still persist, despite its many benefits. According to the European Remanufacturing Network a key challenge is lack of accurate, timely and consistent product knowledge as highlighted in a 2015 survey of 188 European remanufacturers. With more data being produced by electric and hybrid vehicles, this adds to the information complexity challenge already experienced in remanufacturing. Therefore, it is difficult to implement real-time and accurate remanufacturing for the shop floor; there are no papers that focus on this within an electric and hybrid vehicle environment. To address this problem this paper attempts to (1) identify the required parameters/ variables needed for fuel cell remanufacturing by means of interviews (2) rank the variables by Pareto analysis (3) develop a casual loop diagram for the identified parameters/ variables to visualise its impact on remanufacturing (4) model a simple stock and flow diagram to simulate and understand data and information-driven schemes in remanufacturing.

Kinect is a device that has been widely used in many areas since it was released in 2010. Kinect SDK was announced in 2011 and used in many other areas than its original purpose, which was a controller for gaming. In particular, it has been used by a number of artists in digital media art since it is inexpensive and has a fast recognition rate. However, there is a problem. Kinect create 3D coordinates with a single 2D RGB image for x, y value - single depth image for z value. And this creates a significant limitation on the installation for interactivity of media art. Because the Cartesian XY coordinate and the spherical Z coordinate system are used in combination, depth error depending on the distance is generated, which makes real-time rotation recognition and coordinate correction difficult above coordinate system. This paper proposes a real-time calibration method of Kinect recognition range expansion for useful application in the digital media art area. The proposed method can recognize the viewer accurately by calibrating a coordinate in any direction in front of the viewer. 3,400 datasets witch acquire from experiment were measured as five stances: the 1m attention stance, 1m hands-up stance, 2m attention stance, 2m hands-up stance, and 2m hands-half-up stance, which were taken and recorded every 0.5 sec. The experimental results showed that the accuracy rate was improved about 11.5% compared with front measurement data according to Kinect reference installation method.

In this article, we establish some new generalized inequalities of Hilbert-type on time scales delta calculus which considered as similar formulas for inequalities of Hilbert type proved by Chang-Jian, Lian-Ying and Cheung [7]. These inequalities will proved by applying Hölder’s inequality, chain rule on time scales and the mean inequality. As special cases of our results (when T = N and T = R), we get the discrete and continuous inequalities. Also, we can obtain other inequalities in different time scale, like T = q^Z, q > 1.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.