We report a facile route for the green synthesis of trimethylchitosan nitrate-capped silver nanoparticles (TMCN-AgNPs) with positive surface charge. In this synthesis, silver nitrate, glucose, and trimethyl chitosan nitrate (TMCN) were used as silver precursor, reducing agent, and stabilizer, respectively. The reaction was carried out in a stirred basic aqueous medium at room temperature without the use of energy-consuming or expensive equipment. We investigated the effects of the concentrations of NaOH, glucose, and TMCN on the particle size, zeta potential, and formation yield. The AgNPs were characterized by UV-visible spectroscopy, photon correlation spectroscopy, laser Doppler anemometry, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The catalytic activity of the TMCN-AgNPs was studied by the reduction of 4-nitrophenol using NaBH₄ as a reducing agent. We evaluated the antibacterial effects of the TMCN-AgNPs on Acinetobacter baumannii, Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus using the broth microdilution method. The results showed that both gram-positive and gram-negative bacteria were killed by the TMCN-AgNPs at very low concentration (< 6.13 μg/mL). Moreover, the TMCN-AgNPs also showed high antibacterial activity against clinically isolated multidrug-resistant A. baumannii strains, and the minimum inhibitory concentration (MIC) was ≤ 12.25 μg/mL.

When a railway vehicle moves on a curved rail, sliding contact occurs between the rail head side and wheel flange, which wears the wheel flange down. The thinned flange needs to be restored above the required minimum thickness for structural safety. In this study, a new process and welding wire for restoring worn-out railway wheels by submerged arc welding was developed. To characterize the properties of the restored wheel, dilatometric analysis of phase transformation, SEM/EDX analyses, hardness measurement, and residual stress measurement using the X-ray diffraction method were performed. Finally, wear tests with full-size wheel/rail specimens were carried out. It was confirmed that the weld metal was composed of bainitic microstructures as intended, and welding defects were not observed. The wear amount of the restored wheel was greater than that of the base material, but it was less than half of the wear depth of the weld-repaired wheel with ferritic–pearlitic microstructures. The developed process seems applicable to industry.

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

Aluminum base alloys containing chromium (Cr) and zinc (Zn) were produced using extrusion and heat treated powder metallurgy. Cr addition ranged between 5 to 10 wt. % while Zn was added in an amount between 0 to 20 wt. %. Heat treatment processes were performed during powder metallurgy process at different temperatures followed by water quenching. Similar alloys were extruded, with an extrusion ratio of 4.6 to get proper densification. Optical microscopy was used for microstructure investigations of the produced alloys. The element distribution microstructure study was carried out using the Energy Dispersive X-ray analysis method. Hardness and tensile properties of the investigated alloys have been examined. Wear resistance tests were carried out and the results were compared with these of the Al-based bulk alloys. Results showed that the aluminum base alloys containing 10wt. % Chromium and heat treated at 500°C for one hour followed by water quenching exhibited the highest wear resistance and better mechanical properties.

With the increasing use of genome sequencing as a surveillance tool for molecular epidemiology of antimicrobial resistance (AMR), databases and clear nomenclature for AMR gene families are critical. Due to the convoluted nomenclatural history of the integron-associated trimethoprim-resistant dihydrofolatereductase (dfr) gene family, we decided to conduct a literature review, comparative sequence analysis, and phylogenetic investigation of the dfr family, the results of which are presented here and available at the Comprehensive Antibiotic Resistance Database (CARD). Overall, literature review and phylogenetic analysis resolved gene name synonyms based on sequence. We recommend adoption of phylogenetic methods to help guide AMR gene naming efforts and relegation of misleading names to synonyms.

Transparent materials used for facial protection equipment provide protection against microbial infections caused by viruses and bacteria, including multidrug-resistant strains. However, transparent materials used for this type of application are made of materials that do not possess antimicrobial activity. They just avoid direct contact between the person and the biological agent. Therefore, healthy people can get infected through contact of the contaminated material surfaces and this equipment constitute an increasing source of infectious biological waste. Furthermore, infected people can transmit microbial infections easily because the protective equipment do not inactivate the microbial load generated while breathing, sneezing, or coughing. In this regard, the goal of this work consisted of fabricating a transparent face shield with intrinsic antimicrobial activity that could provide extra-protection against infectious agents and reduce the generation of infectious waste. Thus, a single-use transparent antimicrobial face shield composed of polyethylene terephthalate and an antimicrobial coating of benzalkonium chloride has been developed for the next generation of facial protective equipment. The antimicrobial coating was analyzed by atomic force microscopy and field emission scanning electron microscopy with elemental analysis. This is the first facial transparent protective material capable of inactivating enveloped viruses such as SARS-CoV-2 in less than one minute of contact, and the methicillin-resistant Staphylococcus aureus and Staphylococcus epidermidis. Bacterial infections contribute to severe pneumonia associated with the SARS-CoV-2 infection, and their resistance to antibiotics is increasing. Our extra protective broad-spectrum antimicrobial composite material could also be applied for the fabrication of other facial protective tools such as such as goggles, helmets, plastic masks and space separation screens used for counters or vehicles. This low-cost technology would be very useful to combat the current COVID-19 pandemic and protect health care workers from multidrug-resistant infections in developed and underdeveloped countries.

Beetles are by far one of the most successful and diverse insect species. A part of this success is attributed to their elytra which provide various functions such as protection to their bodies from mechanical forces and the harmful environmental factors. In this study, Stag beetle (Lucanus cervus) elytra were first examined for their overall flexural properties and were observed to have a localized shape retaining snap-through mechanism which could play a crucial role in energy absorption, e.g. during battles and falls from heights. The snap-through mechanism was validated using theoretical calculations and also finite element simulations. Elytra were also characterized to examine their puncture and wear resistance. Our results show that elytra resisted puncture up to a force of 1.8±0.4 N and have puncture resistance compared to that of commercially available puncture resistant gloves. The measured values of modulus and hardness of elytra exocuticle were 10.3±0.8 GPa and 0.7±0.1 GPa. Using the hardness to modulus ratio as an indicator of wear resistance, the estimated value was observed to be in the range of wear resistant biological materials. Thus, our study demonstrates different mechanical properties of the stag beetle elytra which can be explored to design shape retaining bio-inspired composites with enhanced puncture and wear resistance.

The aim of this study was to establish the blood glucose response to different cooking methods of pasta. Participants consumed three identical meals in a random order that were freshly cooked (hot), cooled and reheated. Blood glucose concentrations were assessed before, and every 15 minutes after ingestion of each meal for 120 minutes. There was a significant interaction between temperature and time (F_{(8.46-372.34)} = 2.75, p = 0.005), with the reheated (90 minutes) condition returning to baseline faster than both cold (120 minutes) and hot conditions. Blood glucose AUC was significantly lower in the reheated (703 ± 56 mmol L^-1 min^-1) compared with the hot condition (735 ± 77 mmol L^-1 min^-1, t(92) = -3.36, pbonferroni = 0.003), with no significant difference with the cold condition (722 ± 62 mmol L^-1 min^-1). To our knowledge, the current study is the first to show that reheating pasta causes changes in post-prandial glucose response, with a quicker return to fasting levels in both the reheated and cooled conditions compared with the hot condition. The mechanisms behind the changes in post-prandial blood glucose seen in this study are most likely related to changes in starch structure and how these changes influence glycaemic response.

The aim of this paper is to develop a composite coating on St 304 steel employing TIG process. Ti wire cored with graphite powder is used as the means of coating material. The process parameters are varied in order to develop coating with optimum characteristics (i.e., hardness and wear resistance). The microstructure of the coating is analyzed with SEM and XRD. It is found that both of the hardness and wear resistance increase as the current increases while both of these properties decrease as the travelling speed increases. It is found that the coated samples with composite layers have more hardness than the substrate and it could range up to 1100 HV being almost 4.5 times higher than the hardness of St 304. Likewise, the wear resistance of coating is observed to be 4.5 times higher than that of substrate. The high performance of coating, as revealed by microstructural analysis, is due to formation of TiC and Cr₂₃C₆ .The optimum conditions to produce the coating are proposed to be 120 A current and 3.17 mm/s travel speed.

The aim of this work is evaluation of corrosion behavior of SS 304 coated through TIG process. In this work, Ti tube cored with graphite powder was applied. Experimental processes were shown that the optimum parameters for coating procedure are voltage of 15V, current density of 120A and the speed of 2.1mm/s. Investigations on corrosion resistance of coating are shown that not only this composite coating can improve the tribological behavior of this type of stainless steel, but also there is an improvement in its deteriorative property. Moreover, it is observed that mass reduction in coating is 5 times lower than the base metal.

That how to improve the sensitivity and the detection ability of the Large-caliber sensor is critical to satisfy the requirement of heavy vehicle wear condition monitoring. In this paper, we introduced the LC resonance principle to the design of sensor with large flow channel (7mm). The resonant exciting coil increases the impedance change of the exciting circuit caused by wear particles which magnify the current difference between the two exciting coils and improve the sensitivity of the sensor. The resonant induction coil greatly suppresses the interference signals and magnifies the weak induced electromotive force which is beneficial to enhance the detection ability. In order to boost the detectability for different materials particles, a phase controlled variable-frequency exciting system (PCVFES) was adopted to automatically switch the exciting frequency between 284kHz for ferromagnetic particles and 420KHz for non-ferromagnetic particles. For the weak signal detection, based on the essential characteristic of the signal, we apply a simpler method that modified lock-in amplifier (MLIA) rather than the conventional algorithms (Wavelet transform, EMD). Results show that using these methods the sensitivity and the detection ability of the sensor are significantly improved and the 75μm iron particles and 220μm copper particles were successfully detected which realizes the initial abnormal wear monitoring for the large flow project.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

A review of the surface ablation of hominin teeth by attrition, abrasion and erosive wear. The occurrence of these lesions is explored in a sample of South African fossil australopithecine dentitions revealing excessive wear. Interpretation of the nature of the dietary components causing such wear in the absence of carious erosion provides insight into the ecology of the Plio-pleistocene epoch (1-2 million years ago). Fossil teeth inform much of the living past by their retained evidence after death. Tooth wear is the ultimate forensic evidence of lives lived.

1) Background: Respiratory tract infections (RTI) has been known to be a significant health concern for mortality and morbidity since many years. This study was aimed at determining the prevalence of bacterial pathogen causing upper respiratory tract (URTIs) and the susceptibility patterns to frequently used antibiotics among patients attending Abusetta hospital in Tripoli district; 2) Methods: A total of 1,110 throat swabs were collected between Jan, 2011 to December, 2014 and inoculated onto Blood agar, MacCkonkey agar and Chocolate agar then incubated at 37 oC for 24 hours. Bacterial pathogens were determined by bacteriological culture methods and antibiotic susceptibility of the isolates was identified following Clinical Laboratory Standard Institute guidelines (CLSI); 3) Results: Of the 1,110 respiratory samples tested, 71.1% (n = 789) of specimens were positive cultures with the dominant bacterial pathogens being streptococcus pneumonia 43.3% (n = 342), followed by pseudomonas aeruginosa 22.8% (n = 180), staphylococcus aurous 13.8% (n = 109), Escherichia Coli 6.9% (n = 55), Enterobacter spp 6.2% (n = 49), Citrobacter 4.5% (n = 36), and Klebsiella 2.2% (n = 18). Most isolates exhibited resistance against the commonly used antibiotics and to at least one antibiotic; and 4) Conclusions: The level of antibiotic resistance in this study is alarming and brings to light the timely and suitable diagnosis of the common bacteria causes of URTIs and proper antibiotic administration based on susceptibility test.

Ti64 alloy plays a significant role in the biomedical applications such as bioimplants for its excellent biocompatibility. Its usage can be further extended by improving the surface hardness and wear resistance. In this respect, laser surface glazing (LSG), an advanced surface modification technique, is very useful which can produce thin hardened surface layer and strong metallurgical bonding. Investigation of temporal and spatial temperature distributions of laser glazed surface of materials are essential because temperature plays significant role in achieving required surface properties. Therefore, in this study, a 3D Finite element analysis has been developed to perform transient thermal analysis of LSG for Ti64 alloy. The model investigated temperature distribution, depth of modified zone and heating and cooling. The results show that the peak temperature is attained 2095 K for 300 W laser power, 0.2 mm beam width and 0.15 ms residence time. Since this temperature is above the melting point (1933 K) of Ti64 alloy, the melt depth is calculated 22.5 μm. Furthermore, from the simulation results, the average heating and cooling rates are estimated 1.19×10⁷ Ks^-1 and 2.71×10⁶ Ks^-1 respectively which indicate the presence of hard phases in the modified zone.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

Senna alata (Linn) Roxb. plant is widely used to manage various infections in folkloric medicine. Methicillin-resistant Staphylococcus aureus (MRSA) infection continues to be a major global public health problem. This study aims to investigate the bioactive components of S. alata leaves active against MRSA. The leaves of S. alata were sequentially extracted and fractionated using standard methods and screened for activities against MRSA. The diethyl ether active thin layer chromatography (TLC) spot was subjected to infrared (IR) and gas chromatography-mass spectroscopic (GC-MS) studies. The aqueous extract and diethyl ether fraction of S. alata leaves elicited the highest activity against the MRSA. The GC-MS analysis of the fraction produced 15 eluates; only the sub-fraction 13 was effective. The TLC analysis of the sub-fraction 13 revealed three spots; only the second spot produced activity. The GC-MS result of the spot showed six peaks. The spectral results for peak 3 match the data from the IR study suggestive of 9-octadecenoic acid methyl ester. Senna alata leaves possess bioactive compounds closely related to 9-octadecenoic acid methyl ester with potent antibacterial activity against MRSA.

Background: Breast cancer is the leading cause of cancer mortality and morbidity among Indonesian women. Identification of biological pathways leading into therapeutic resistance through in vitro model is an important step to develop alternative effective therapy in breast cancer. Loss of PTEN expression has been associated with resistance to chemotherapy by involving PI3K/PTEN- dependent apoptosis pathway. We conducted in vitro experiment to investigate the association of hsa-miR-21 and PTEN expression in Doxorubicin-resistant MCF-7 cell line. Methods: Parental MCF-7 cells were periodically incubated with Doxorubicin to obtain specific Dox-resistant variant determined by IC50 using MTT assay. PTEN protein expression was analyzed using immunocytochemistry. Expression of mature has-miR-21 was measured using qRT-PCR. Results: The IC50 of Doxorubicin in parental MCF-7 and Doxorubicin-resistant MCF-7 cells (MCF-7/Dox) was 0.68 and 5.78 µg/ml, respectively. Hsa-miR-21 was significantly overexpressed in MCF-7/Dox cells compared to parental MCF cells (7.94 fold changes). Conclusion: PTEN and hsa-miR-21 expression levels were negatively correlated in Doxorubicin resistant-MCF cells. Further study to confirm the causal relationship of miR-21 overexpression and PTEN downregulation in MCF-7/Dox is required.

Resistance to hormone therapy and disease progression is the major challenge in clinical management of prostate cancer (PC). Drugs currently used in PC therapy initially show a potent antitumor effect. Nevertheless, PC gradually develops resistance, relapses and spreads. Most patients develop, indeed, castrate-resistant PC (CRPC), which is almost incurable. The nerve growth factor (NGF) acts on a variety of non-neuronal cells by activating the NGF tyrosine-kinase receptor, TrkA. NGF signaling is deregulated in PC. In androgen-dependent PC cells, TrkA mediates the proliferative action of NGF through its cross talk with the androgen receptor (AR). Epithelial PC cells, however, acquire the ability to express NGF and TrkA, as the disease progresses, indicating a role for NGF/TrkA axis in PC progression and androgen-resistance. We here report that once activated by NGF, TrkA mediates proliferation, invasiveness and epithelial-mesenchyme transition (EMT) in various CRPC cells. NGF promotes organoid growth in 3D models of CRPC cells, and specific inhibition of TrkA impairs all these responses. Thus TrkA represents a new biomarker to target in CRPC.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Macrophages are cells involved in the primary response to debris derived from wear of implanted CoCr alloys. The biocompatibility of wear particles from a high carbon CoCr alloy produced under polarization in physiological hyaluronic acid (HA) solution was evaluated in J774A.1 mouse macrophages cultures. Polarization was applied to mimic the electrical interactions observed in living tissues. Wear tests were performed in a pin-on-disk tribometer integrating an electrochemical cell in phosphate buffer solution (PBS) and in PBS supplemented with 0.3% HA, physiological synovial fluid concentration, used as lubricant solution. Wear particles produced in 0.3% HA solution showed a higher biocompatibility in J774A.1 macrophages in comparison to those elicited by PBS. A considerable improvement in macrophages biocompatibility in the presence of 0.3 % of HA was further observed by the application of polarization at potentials having current densities typical of injured tissues suggesting that polarization produces an effect on the surface of the metallic material that leads to the production of wear particles that are macrophages biocompatible and less cytotoxic. The results showed the convenience to consider electric interactions together with other particles parameters, as are size and composition, to get a better understanding of the biological effects of the wear products.

The exfoliation of graphene has opened a new frontier in material science with a focus on 2D materials. The unique thermal, physical and chemical properties of these materials have made them one of the choicest candidates in novel mechanical and nano-electronic devices. Notably, 2D materials such as graphene, MoS2, WS2, h-BN, and Black Phosphorus have shown outstanding lowest frictional coefficients and wear rates, making them attractive materials for high-performance nano-lubricants and lubricating applications. The objective of this work is to provide a comprehensive overview of the most recent developments in the tribological potentials of 2D materials. At first, the essential physical, wear, and frictional characteristics of the 2D materials including their production techniques are discussed. Subsequently, the experimental explorations and theoretical simulations of the most common 2D materials are reviewed in regards to their tribological applications such as their use as solid lubricants and surface lubricant nano-additives. The effects of micro/nano textures on friction behavior are also reviewed. Finally, the current challenges in tribological applications of 2D materials and their prospects are discussed.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

Acetyleugenol is a phytochemical compound with broad effect against infectious diseases and tumors. Here, we extracted, characterized and elucidated the structure of acetyeugenol, for the first time, from the leaves of Acacia nilotica (L.)―a well-known medicinal plant. The broad antibacterial potential of acetyleugenol was first confirmed against seven bacterial pathogenic isolates with best activity against Proteus sp., Salmonella typhi, Staphylococcu aureus, and Streptococcus pneumonia, which showed similar or better zone of inhibition to that of the control amoxicillin. To further investigate its effect against Mycobacterium tuberculosis, acetyleugenol and its indole and phenyl analogs were subjected to molecular docking experiments against two potential tuberculosis drug targets―MtPknE and MtPknB Ser/Thr protein kinases. The results reveal that all of the analogs have improved docking scores comparing to the acetyleugenol. The indole analogs EUG-1 and EUG-3 were more effective with better docking scores for MtPknE with –11.08 and –10.05 kcal/mol, respectively. Similar results were obtained for the MtPknB. In contrast, only the EUG-2 phenyl analog has given rise to similar docking scores for both targets. This opens the door for further comprehensive studies on these acetyleugenol analogs with in vitro and in vivo experiments to validate and get more insights into their mechanisms of action.

In the manufacturing industry, cutting tool failure is a probable fault which causes damage to the cutting tools, workpiece quality and unscheduled downtime. It is very important to develop a reliable and inexpensive intelligent tool wear monitoring system for use in cutting processes. A successful monitoring system can effectively maintain machine tools, cutting tool and workpiece. In the present study, the tool condition monitoring system has been developed for Die steel (H13) milling process. Effective design of experiment and robust data acquisition system ensured the machining forces impact in the milling operation. Also, ANFIS based model has been developed based on cutting force-tool wear relationship in this research which has been implemented in the tool wear monitoring system. Prediction model shows that the developed system is accurate enough to perform an online tool wear monitoring system in the milling process.

In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

Stainless steel grade AISI 304 is one of the most widespread modern structural material, alas its sliding wear and cavitation wear resistance are limited. Thus, AlTiN and TiAlN coatings can be deposited for increasing the resistance to wear of stainless steel components. The aim of the work was to investigate the cavitation erosion and sliding wear mechanisms of magnetron sputtered AlTiN and TiAlN coatings deposited on SS304 stainless steel. Films surface morphology and structure were examined using a profilometer, light optical microscope (LOM) and scanning electron microscope (SEM). The mechanical properties (hardness, elastic modulus) were tested by nanoindentation tester. The adhesion of deposited coatings was determined by means of the scratch test and Rockwell test. Cavitation erosion tests were performed according to ASTM G32 (vibratory apparatus) with stationary specimen procedure. Sliding wear tests were conducted using a nano-tribo testes i.e. ball-on-disc apparatus. Wear mechanisms are strongly contingent upon the structure and morphology of the tested materials. In relation to stainless steel substrate, the PVD films present a superior resistance to sliding wear and cavitation erosion. Higher resistance was noticed for AlTiN than for TiAlN film, mainly due to its superior hardness and elastic modulus. Cavitation erosion mechanism of both, AlTiN and AlTiN coatings is prone to embrittlement, imputable to fatigue processes that result in coating rupture and spallation that consist in coating fragmentation, formation of pits and finally detachment from the substrate. Additionally, films nanoindentation results measured before and after cavitation testing indicate changes in coatings structure, that acknowledged wear mechanism that starts with coating internal delamination in flake spallation mode. In contrary to PVD coatings, steel substrate is characterized by developed cavitation erosion wear with roughened surface and plastically deformed, semi-brittle, eroded surface. Sliding wear of thin films is based on micro-ploughing mechanism. For stainless steel adhesive sliding wear mode and plastic deformation with smearing, material transfer and grooving were observed. It was confirmed that various fluid machinery components made from austenitic stainless steel that undergo cavitation erosion, can be prevented by deposition of AlTiN and TiAlN films.

The management of carbapenem-resistant infections is often based on colistin, tigecycline, aminoglycosides and their combinations. However, in a recent systematic review we found that Gram-negative bacteria (GNB) co-resistant to carbapanems, aminoglycosides, colistin and tigecycline (CACT-resistant) are increasingly being reported worldwide. Clinical data to guide the treatment of CACT-resistant GNB are scarce and based exclusively on few case reports and small case series but seem to indicate that appropriate (in vitro active) antimicrobial regimens, including newer antibiotics and synergistic combinations, may be associated with lower mortality. In this review we consolidate the available literature to inform clinicians dealing with CACT-resistant GNB about treatment options by considering the mechanisms of resistance to carbapenems. In combination with rapid diagnostic methods that allow fast detection of carbapenemase production, the approach proposed in this review may guide a timely and targeted treatment of patients with infections by CACT-resistant GNB. Specifically, we focus on the three most problematic species, namely Klebsiella pneumoniae, Pseudomonas aeruginosa and Acinetobacter baumannii. Several treatment options are currently available for CACT-resistant K. pneumonia. Newer β-lactam-β-lactamase combinations, including the combination of ceftazidime/avibactam with aztreonam against metallo-β-lactamase-producing isolates, appear to be more effective compared to combinations of older agents. Options for P. aeruginosa (especially metallo-β-lactamase-producing strains) and A. baumannii remain limited. Synergistic combination of older agents (e.g. colistin- or fosfomycin-based synergistic combinations) may represent a last resort option but their use against CACT-resistant GNB requires further study.

Resistant cancer often shows a particular secretory trait such as heat shock proteins (HSPs) and extracellular vesicles (EVs), including exosomes and oncosomes surrounded by lipid bilayers. Lipoproteins are biochemical assemblies that transport hydrophobic lipid (a.k.a. fat) molecules in body fluid and are composed of a single-layer phospholipid and cholesterol outer shell, lipids molecules within the particles, and apolipoproteins embedded in the membrane. However, lipoprotein storage and secretion by cancer cells have not well-investigated yet. We found lipoproteins were stored and abundantly secreted by neuroendocrine, castration-resistant prostate cancer (NEPC / CRPC) cells but barely secreted by colon cancer cells and oral squamous cell carcinoma (OSCC) cells. In addition, large EVs (approx. 300 nm diameter) and potential oncosomes were released by CRPC and OSCC cells. Proteomics revealed that CRPC cells secreted EVs enriched with tetraspanins and extracellular matrices which were reduced upon heat shock stress and alternatively lipoproteins and HSPs were secreted upon stress. Heat shock stress triggered secretion of lipoprotein-EV complexes that contained apolipoprotein A, B, C and E. These data suggested that vesicular assembly composed of EVs and lipoproteins enriched with cholesterols and phospholipids may be stored in resistant cancer cells but released upon cell stress that is increased in cancer therapies.

This manuscript deals with the cavitation erosion resistance of low-velocity oxy-flame (LVOF) sprayed Al2O3–40%TiO2/NiMoAl cermet coatings, a new functional application of cermet coatings. The aim of the study was to investigate the cavitation erosion mechanism and determine the effect of feedstock powder ratio (Al2O3–TiO2/NiMoAl) of LOVF cermet coatings on their cavitation erosion resistance. As-sprayed coatings were investigated for roughness, porosity, hardness, Young’s modulus. Microstructural characteristics of the cross-section and the surface of as-sprayed coatings were examined by light optical microscopy (LOM) and scanning electron microscopy (SEM) equipped with the EDS and XRD methods. Coatings cavitation tests were conducted in accordance with the ASTM G32 standard with usage of reference samples made from steel, copper and aluminum alloys. Cavitation erosion resistance was measured by weight and volume loss, and normalised cavitation erosion resistance was calculated. Surface eroded due to cavitation was examined in successive time intervals by LOM and SEM-EDS. On the basis of coating properties and cavitation investigations, a phenomenological model of the cavitation erosion of Al2O3–40%TiO2/NiMoAl cermet coatings was elaborated. General relationships between their properties, microstructure and cavitation wear resistance were established. The Al2O3–40%TiO2/NiAlMo composite coating containing 80% of ceramic powder has a higher cavitation erosion resistance than the reference aluminium alloy.

Once a wheat sheaf has been sealed and tied up, its packed down straws display the same orientation and zero-divergence. This observation brings us to the mathematical notion of presheaf, i.e., a topological structure in which diverging functions are locally superimposed. We show how the concepts of presheaves and the correlated globular sets, borrowed from category theory and algebraic topology, allow a well-founded mathematical approach to otherwise elusive activities of the brain. The mathematical assessment of brain functions in terms of presheaves: a) explains why spontaneous random spikes synchronize; b) leads to the counterintuitive intuition of antidromic effects in neuronal spikes: when an entrained oscillation propagates from A to B, changes in B lead to changes in A. We provide testable previsions: a) we suggest the proper locations of transcranial magnetic stimulation’s coils to improve the clinical outcomes of drug-resistant epilepsy; b) we advocate that axonal stimulation by external sources backpropagates and alters the neuronal electric oscillatory frequency. Further, we describe how the hierarchical information transmission inside globular sets provides fresh insights concerning different issues at various coarse-grained scales, such as object persistence, memory reinforcement in spite of random noise, Bayesian inferential circuits.

Varroa destructor is considered one of the most devastating parasites of the honey bee, Apis mellifera, and a major problem for the beekeeping industry. Currently, the main method to control Varroa mites is the application of drugs that contain different acaricides as active ingredients. The pyrethroid tau-fluvalinate is one of the acaricides most widely used in beekeeping due to its efficacy and low toxicity to bees. However, the intensive and repetitive application of this compound produces a selective pressure that, when maintained over time, contributes to the emergence of resistant mites in the honey bee colonies, compromising the acaricidal treatments efficacy. Here we studied the presence of tau-fluvalinate residues in hives and the evolution of genetic resistance to this acaricide in Varroa mites from honeybee colonies that received no pyrethroid treatment in the previous four years. Our data revealed the widespread and persistent tau-fluvalinate contamination of beeswax and beebread in hives, an overall increase of the pyrethroid resistance allele frequency and a generalized excess of resistant mites relative to Hardy-Weinberg equilibrium expectations. These results suggest that tau-fluvalinate contamination of the hives may seriously compromise the efficacy of pyrethroid-based mite control methods.

Outer particles collision with certain dynamic object is not a pure impact wear behavior; it is typically accompanied by sliding wear phenomena. This study aimed investigating the impact-sliding wear performance of three different TC17 titanium alloys. One was untreated, and the other two were subjected to laser shock peening (LSP) by 5 and 7 J pulse energy, respectively. Wear test was performed on a novel impact-sliding wear testing rig, which can realize multiple impact-sliding motions by changing motion parameters in x and z directions. Present results showed that wear resistance of both treated samples improved compared with the untreated alloy. Given the increase in wear cycles, increment in wear rate of the untreated sample was constantly higher than those of treated samples. All results can be attributed to the increase in surface hardness of the material and residual compressive stress, which was also introduced after LSP.

In this study, we discuss the properties of absolute vacuum space and how these properties can play a vital role in creating a mechanism in which the very first particle gets created simultaneously everywhere and we find the limit in which when the absolute vacuum volume reaches will lead to the collapse that leads to the creation of the first particle. This discussion is made following to the elementary dimensions theory study that was peer-reviewed at the end of 2020, everything in the universe is made from four elementary dimensions, these dimensions are the three spatial dimensions (X, Y, and Z) and the Vacuum resistant as the factor of change among the four, time itself wasn’t considered as the fourth dimension, rather time corresponds to a factor of change, and during the research it was found out that the Vacuum resistant is the factor of change in the Absolute Vacuum space, where time is a hypothetical concept, that represents changes during certain events compared to a constant change rate event.Therefore, time does exist, but as a factor of change, and as the Vacuum resistant in the absolute vacuum space, Time= factor of change= Vacuum resistant. In the study, the internal and external vacuum resistant volume equivalent is found, External Vacuum resistant=3.2857602*10^15 *mass. This equation is used to identify the amount of Free external vacuum resistant created during nuclear fission and fusion: Initial mass of the excited nucleuses mass of the created new nucleuses+ 3.2857602*10^15 * the lost Mass. In elementary dimensions, the energy created during nuclear reactions is equivalent to the free External vacuum resistant created through nuclear reactions, and mass is equivalent to the internal Vacuum resistant.

Antimicrobial resistance (AMR) is a recurring global problem, which constantly demands new antimicrobial compounds to challenge the resistance. It is well known that essential oils (EOs) have been known for biological activities including antimicrobial properties. In this study, EOs from seven aromatic plants of Asir region of southwestern Saudi Arabia were tested for their antimicrobial efficacy against four drug resistant pathogenic bacterial isolates (Staphylococcus aureus, Streptococcus pyogenes, Escherichia coli and Streptococcus typhimurium) and one fungal isolate (Candida albicans). Chemical compositions of EOs were determined by Gas chromatography-Mass Spectrometry (GC-MS). The results revealed that EOs from Mentha cervina, Ocimum basilicum and Origanum vulgare proved most active against all isolates with inhibitory zone range between17 to 45 mm. The lowest minimum inhibitory concentration (MIC) of 0.025mg/ml was observed for Staph. aureus and Streptococcus pyogenes with EO of Origanum vulgare. All the three EOs showed significant anti candida activity. Together form the results the EOs from Mentha cervina, Ocimum basilicum and Origanum vulgare demonstrated a significant antimicrobial efficacy against drug resistant microorganisms.

The problem of drug resistance in terms of antifungal therapy, unknown until a few years ago, is assuming increasing importance. Particularly in immunosuppressed patients and subject to chemotherapy and radiotherapy. In the last years the use of essential oils as approach to improving the effectiveness of antifungal agents and reducing the antibiotic resistant has been proposed. Our research aimed to evaluate the antifungal activity of Colombian essential oil of Ruta graveolens (REO) against clinical strains of Candida albicans, Candida parapsilopsis, C. glabrata and Candida tropicalis. The data obtained showed that Candida tropicalis and Candida albicans were most sensible strains showing minimum inhibitory concentrations (MIC) of 0.5 and 1.0 µg/ml of REO. The Time Kill Kinetics assay demonstrated that REO showed fungicide effect against C. tropicalis and fungistatic effect against C. albicans. In addition, the 40% of the biofilm formed by C. albicans was eradicated using 1% of REO after 1 hour of exposure.

Necrotizing pneumonia due to Methicillin-Resistant Staphylococcus Aureus (MRSA) is devastating and difficult to treat in preterm infants. We report a case of severe MRSA necrotizing pneumonia in a preterm infant. As an add-on rescue therapy to vancomycin, linezolid rapidly cured this case after the failure of vancomycin plus rifampicin. This rapid cure suggests that adjunctive rather than rescue linezolid may be considered in such cases.

Biosensors have shown great potential in realizing rapid, low cost and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induce dieletrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labelling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nano-structured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies /µL MRSA gDNA) and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detection of other infectious agents.

True contact between solids with randomly rough surfaces tends to occur at a large number of microscopic contact patches. So far, two scaling regimes have been identified for the number density n(A) of contact-patch sizes A in elastic, non-adhesive, self-affine contacts. At small A, n(A) is approximately constant, while n(A) decreases as a power law at large A. Using Green’s function molecular dynamics, we identify a characteristic (maximum) contact area Ac above which a superexponential decay of n(A) becomes apparent if the contact pressure is below the pressure p_cp at which contact percolates. We also find that A_c increases with load relatively slowly far away from contact percolation. Results for A_c can be estimated from the stress autocorrelation function G_σσ (r) with the following argument: the radius of characteristic contact patches, r_c, cannot be so large that G_σσ (r_c) is much less than p_c². Our findings provide a possible mechanism for the breakdown of the proportionality between friction and wear with load at large contact pressures and/or for surfaces with a large roll-off wavelength.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

In interepidemic periods, a sapronoses typically employs a variety of mechanisms for maintaining viability of its causative agent in terrestrial parasitic systems, associated with different adaptive strategies utilized by its populations to survive. Unlike spore-forming bacteria, causative agents of sapronoses use resistant cell forms, which is a viable but nonculturable (VBNC) state, and persistence. Implementation of these strategies is conditioned by effects of various stress factors of the habitat and is characterized by decreased metabolism, alteration of the morphology and physiology of bacterial cell, and cessation of its replication. It is important that the resistant forms of cells retain virulence and, as favorable conditions come, turn back into the active vegetative form again. The discovery of the genetic modules of bacterial toxin–antitoxin systems in recent years has made it possible to identify a number of complicated regulatory molecular mechanisms responsible for maintaining the pathogenic potential of resistant forms of causative agents of natural-focus sapronoses in interepidemic periods.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

The purpose of this study is to examine the relationship between the institutional investors which can affect financial performance for corporate sustainability on the income smoothing. Therefore, this study focus on the connection between the nature of stock rights and income smoothing in China. For this study, hypotheses were established on the relationship each state-controlled companies, income smoothing, and information equilibrium of individual investors, and empirical analysis was conducted through related variables. The analysis results are summarized in three categories as follows. First, this research finds that state-controlled firms (CONTs) prefer income smoothing activities compared to non-state-controlled firms for the long-term sustainable development of firms using data from 2011 to 2019. Second, this study found out that Institutional investors support the behavior of CONTs to smooth their earnings because this behavior is seen as an attempt by CONTs to convey valuable private information to other investors. Third, we was able to discover that institutional investors' monitoring effect is predominantly driven by pressure-resistant institutional investors. This research complements the lack of empirical research on income smoothing and enable to give a guideline that the type of stock rights is a critical key determinant of participation in income smoothing activities for stable growth and sustainability in the future.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

Combining Matrix-Assisted Laser Desorption/Ionization Time-of-Flight (MALDI-TOF) spectra data and artificial intelligence (AI) has been introduced for rapid prediction on antibiotic susceptibility test (AST) of S. aureus. Based on the AI predictive probability, the cases with probabilities between low and high cut-offs are defined as “grey zone”. We aimed to investigate the underlying reasons of unconfident (grey zone) or wrong predictive AST. A total 479 S. aureus isolates were collected, analyzed by MALDI-TOF, and AST prediction, standard AST were obtained in a tertiary medical center. The predictions were categorized into the correct prediction group, wrong prediction group, and grey zone group. We analyzed the association between the predictive results and the demographic data, spectral data, and strain types. For MRSA, larger cefoxitin zone size was found in the wrong prediction group. MLST of the MRSA isolates in the grey zone group revealed that uncommon strain types composed 80%. Amid MSSA isolates in the grey zone group, the majority (60%) was composed of over 10 different strain types. In predicting AST based on MALDI-TOF AI, uncommon strains and high diversity would contribute to suboptimal predictive performance.

Infections by methicillin-resistant Staphylococcus aureus (MRSA) are continuously expanding within the community. Chicken meat is usually contaminated by MRSA, and this contaminated chicken meat is an important source of foodborne infections in humans. In this study, a cross-sectional supershop survey was conducted to determine the prevalence and antimicrobial resistance pattern of MRSA in 113 domestic frozen chicken meat samples purchased from nine branded supershops available in five divisional megacities of Bangladesh. The study also focused on the determination of methicillin resistance gene in MRSA isolates. S. aureus was identified by standard culture-based and molecular methods, and subjected to antimicrobial susceptibility testing. MRSA was screened by cefoxitin disk diffusion test. Methicillin resistance gene was identified by PCR. Of samples, 54.9% were positive for S. aureus, and, of these, 37.1% isolates were identified as MRSA. All the isolates were multidrug resistant (MDR): 52.2% were resistant to 6−8 antimicrobial classes, and 47.8% isolates to 9−12 classes. Three (3.2%) isolates of S. aureus were possible extensively drug resistant. The highest rates of resistance were observed against cefoxitin (100%), followed by nalidixic acid, ampicillin and oxacillin (97.7%), colistin (91.3%), amoxicillin-clavulanic acid and amoxicillin (87%), penicillin-G and cloxacillin (82.6%), oxytetracycline (78.3%) and cefixime (73.9%). Screening of methicillin resistance gene revealed that 43.5% isolates of MRSA were positive for mecA gene. The high prevalence of MDR MRSA in frozen chicken meat samples in this study emphasizes the need for better sanitary education of food handlers in hygienic practices focusing on their potential role as reservoirs and spreaders of MRSA.

In California, an average of 41,900 patients are diagnosed annually with Staphylococcus bacterial infection; out of these, 24,090 patients have methicillin-resistant Staphylococcus aureus (MRSA) infection and 17,810 patients have methicillin-sensitive Staphylococcus aureus (MSSA) infection. The aim of this paper is to find out whether there is a significant difference in strain dominancy and in what direction. The paper gathered and analyzed data for period of five years of infection rate due to Staphylococcus aureus. This study indicates that a significant difference in dominancy exists, the MRSA infection rate (an average of five years period) is 1.35 times higher than the MSSA infection rate (P-value < 0.05, CI: 95%), but the gap between the two infection rates is decreasing. The infection rate of both MRSA and MSSA is in a path of decline.

In this work, nylon 6/ P(N-phenylmaleimide-alt-styrene) blends were prepared by melt blending, and the mechanical, heat-resistant, crystallographic and dynamical mechanical properties of nylon 6/ P(N-phenylmaleimide-alt-styrene) blends with different contents were investigated and analyzed. The results showed that the mechanical properties decreased with increasing PNS, while the heat deflection temperature (HDT), relative crystallinity (Xn), and storage modulus (G’) increased with increasing PNS. The results of differential Scanning Calorimetry (DSC) proved the PNS played the positive role of nucleating PA6. And the results of dynamic mechanical analysis (DMA) proved the PNS could improve the rigidity of PA6/PNS blends. From the SEM, these PNS domains were between 0.2 and 4 μm in diameter. The experimental results indicated that the addition of PNS improved the rigidity of PA6/PNS blends, and then improved the heat-resistant property.

The lack of knowledge on the link between the manufacturing process and performances constitutes a major issue of brake lining development. This study focuses on the effect of mixing duration on properties and tribological behavior of organic friction composite materials. The adopted methodology is based on efficient simplified formulations to limit synergic effects by the reduction of number and size distribution of constituents. Microstructural characteristics are analyzed and correlated to thermo physical and mechanical properties. Wear mechanisms and tribological behavior are studied in relation with the given microstructure and material properties. In the elaboration process, mixing duration has an impact on particle distribution and fibre arrangement. Distribution and size of fibre entanglements are found to cluster carbonaceous particles, which creates bulk thermal bridges improving thermal conductivity. Moreover, rockwool fibre arrangements affect density, porosity and thermo-physical properties. In addition, mixing duration disrupts cohesion of fibre bundles with the matrix, affecting compressive modulus and wear behaviour. This microstructural defect fosters an abundant third-body source flow, which results in a high wear flow. Porosities induced by fibre entanglements, presenting large and irregular size and distribution on the friction surface, lead to a low wear resistance and change the stability of friction.

Multi-modal Motion-assisted Memory Desensitization and Reprocessing Therapy (3MDR), an interactive, virtual-reality assisted, exposure-based intervention for PTSD, has shown promising results for treatment-resistant Posttraumatic Stress Disorder (TR-PTSD) among military members (MMs) and Veterans in Randomized Controlled Trials. Previous research has suggested that emotional regulation (ER) and emotional dysregulation (ED) may be factors which are correlated with symptom severity and maintenance of TR-PTSD. This embedded mixed-methods pilot study (n=9) sought to explore the impact of 3MDR on ER and ED of MMs and Veterans. Difficulties in Emotional Regulation Scale (DERS-18) data was collected at baseline, prior to each session, and at 1 week, 1 month and 3 months post-intervention and analyzed using a Wilcoxon signed-ranks test. Qualitative data collected from sessions, debriefs, and follow-up interviews were transcribed and descriptively analyzed. Results demonstrated statistically significant decreases in DERS-18 scores from pre-intervention to post-intervention at each timepoint. Qualitatively, participants perceived improvements in ER within specified DERS-18 domains. We describe how 3MDR’s unique and novel approach may address ED through cognitive-motor stimulation, narration, divergent thinking, reappraisal of aversive stimuli, dual-task processing, and reconsolidation of traumatic memories. Further investigation is underway to better understand the underlying neurobiological mechanisms by which 3MDR addresses ER and PTSD.

For polymicrobial infections, AtbFinder utilizes a novel paradigm of the population response to antibiotics, enabling bacterial growth in the form of a mixed microbial community and selecting the antibiotics targeting not only the principal pathogen, but also those bacteria that support their growth. TGV medium allowed culturing a more diverse set of bacteria from polymicrobial biospecimens, compared with that achieved with the standard media and enabled, already within 4h, accurate selection of the antibiotics that completely eliminated all cultivatable bacteria from clinical samples. In conclusion, AtbFinder system may be a valuable tool in improving antibiotic selection, enabling targeted empirical therapy and accurate antibiotic replacement, which is especially important in high-risk patients.

Bifidobacteria have long been recognized as bacteria with probiotic and therapeutic features. The aim of this work is to characterize the Bifidobacterium asteroides BA15 and BA17 strains, isolated from honeybee gut. An in-depth assessment was carried out on safety properties (antibiotic resistance profiling, β-haemolytic, DNAse and gelatinase activities and virulence factor presence) and other properties (antimicrobial activity, auto-aggregation, co-aggregation and hydrophobicity). Based on phenotypic and genotypic characterization, both strains satisfied all the safety requirements. More specifically, genome analysis showed the absence of genes encoding for glycopeptide (vanA, vanB, vanC-1, vanC-2, vanD, vanE, vanG), resistance to tetracycline (tet-M, tet-L and tetO), and virulence genes (asa1, gelE, cylA, esp, hyl).

From the wide range of engineering materials traditional Stellite 6 alloy exhibits excellent cavitation erosion (CE) resistance. In this work, the effect of nitrogen ion implantation of HIPed Stellite 6 on the improvement of CE resistance and both cobalt-rich matrix phase transformation due to nitrogen implantation and CE were stated. The CE resistance of stellites ion-implanted by 120 keV N+ ions two fluences: 5x1016 cm-2 and 1x1017 cm-2 were comparatively analysed with the unimplanted stellite and AISI 304 stainless steel. CE tests were conducted according to ASTM G32 with stationary specimen method. Erosion rate curves and mean depth of erosion confirm that the nitrogen implanted HIPed Stellite 6 two times exceeds the resistance to CE than unimplanted stellite, and has almost 10 times higher CE reference than stainless steel. The X-ray diffraction (XRD) confirms that HIPed Stellite 6 nitrogen ion implantation favours transformation of the ɛ(hcp) to γ(fcc) structure. Unimplanted stellite ɛ-rich matirx is less prone to plastic deformation than γ and consequently, increase of γ phase effectively holds carbides in cobalt matrix and prevents Cr7C3 debonding. This phenomenon elongates three times the CE incubation stage, slows erosion rate and mitigates the material loss. Metastable γ structure formed by ion implantation consumes the cavitation load for work-hardening and γ → ɛ martensitic transformation. In further CE stages, phases transform as for unimplanted alloy namely, the cavitation-inducted recovery process, removal of strain, dislocations resulting in increase of fcc phase. The CE mechanism was investigated using a surface profilometer, atomic force microscopy, SEM-EDS and XRD. HIPed Stellite 6 wear behaviour relies on the plastic deformation of cobalt matrix, starting at Cr7C3/matrix interfaces. Once the Cr7C3 losing their restrain, are debonding and removed. Carbides detachment creates cavitation pits which initiate cracks propagation through cobalt matrix, the loss of matrix phase and CE proceeds with a detachment of massive chunk of materials.

Manufacturing of grinding wheels is continuously adapting to new industrial requirements. New abrasives and new wheel configurations, together with wheel wear control allow for grinding process optimization. However, the wear behavior of the new abrasive materials is not usually studied from a scientific point of view due to the difficulty to control and monitor all the variables affecting the tribochemical wear mechanisms. In this work an original design of pin on disk tribometer is developed in a CNC grinding machine. An Alumina grinding wheel with special characteristics is employed and two types of abrasive are compared: White Fused Alumina (WFA) and Sol-Gel Alumina (SG). The implemented tribometer reaches sliding speeds of between 20 and 30 m/s and real contact pressures up to 190 MPa. The results show that the wear behavior of the abrasive grains is strongly influenced by their crystallographic structure and the tribometer appears to be a very good tool for characterizing the wear mechanisms of grinding wheels, depending on the abrasive grains.

With the emergence of blockchain and smart contracts, traditional digital applications 1 such as identity management, supply chain management, banking and finance etc. are expected 2 to be transformed into Decentralized Applications (DApps). Blockchain interoperability is a new 3 and exciting aspect of blockchain technology that is quickly gaining popularity in many industries. 4 However, the widespread use of blockchains has not yet been achieved because DApps running on the 5 blockchain using smart contracts require access to authentic off-chain data. Users are more conscious 6 of their personal data privacy and consequently are more reluctant to share their data, posing a 7 challenge in the adoption of DApps. To solve this challenge, we present a novel quantum-resistant, 8 data authentication and zero-knowledge proof scheme named zk-DASTARK. Based on our proposed 9 scheme, we present a novel framework which can be used to feed authenticated off-chain data to 10 DApps without compromising user data privacy. Our proposed framework is quite efficient against 11 well-known off-chain data authentication frameworks. The proposed framework is implemented on 12 state-of-the-art quantum-resistant IOTA Blockchain and is highly efficient as it takes approximately 13 60 ms to generate a proof and approximately 10 ms to verify a proof.

The article describes the study of the properties of polytetrafluoroethylene, modified using natural layered silicates—serpentinite. It is shown that the introduction of a small amount of layered silicates significantly increases the tribological characteristics of the material. The additional introduction of magnesium nano-spinels facilitated the formation of an intercalated polymer-silicate nanocomposite.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

AMR and drug void have caused huge panic today with few thousand death per year. MDR Typhoid was a serious old disease and caused serious health hazard in humen and animals demanding an update on molecular biology of the status on transferable genetic elements. R-plasmids combined in F’-plasmid and the new MDR conjugative plasmids were shown abundant in Sanmonella ranging 70-440kb with similarities. BlaTEM, blaCTX-M, blaOXA, blaNDM mdr genes were abundant in >50 plasmids analyzed and metal resistant gene clusters are predominant in most large plasmids. Among the acetyltransferase all catA1, aacA1 and aac-1b-cr genes were located. Abundant streptomycin phosphotransferases (StrAB) and rarely colistin resistant Mcr-5/9 phosphoethanolamine–lipid A transferase were detected. Altered isomeric dihydropterote synthases (Sul1/2/3) were present giving sulfamethoxazole resistance and dhfr gene frequently associated giving trimethoprim resistance. Metal resistant gene clusters like SilABC (CusABC), PcoAB, RcnA, terABC, and merABCXT etc were found in many Salmonella enterica plasmids. Toxin genes like HipA and virulence genes like spvABD were located in few plasmids increasing virulence and pathogenesis. Drug efflux genes tetA or tetB and OqxB, floR, CmlA were frequent where as QepA and EamA genes were rarely seen. Thus, Salmonella metal resistant genes combined with antibiotic resistant genes has tried to overcome the both toxic antibiotics and metalions causing Typhoid AMR. Such acquisition spreads salmoniasis in the live stocks (pig, cow, chicken) where toxic soil and water dominate increasing chance of MDR typhoid in human.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

The concept of friction damper is widespread technique and used to reduce the structural vibrations in many industrial applications. These friction dampers are generally coated with low wear rate materials to reduce the fretting wear. This paper investigates the use of physical vapor deposition (PVD) nitride based AlTiN coating material applied over the stainless steel friction damper to enhance the damping capacity and to reduce the fretting wear. A friction test rig has been developed to measure the dynamic hysteresis characteristics of friction damper at high temperature (700 °C). The damping capacity and fretting wear analysis is carried out at room temperature, 300 °C and 600 °C. The force versus displacment characterisitcs curve is used to predict the damping capacity and fretting wear analysis is carried out at microscopic level for the comparision. It is observed that at room temperature AlTiN coated friction damper has not much influence to improve the damping capacity and to reduce the fretting-wear. However, at high temperature it has better damping capacity and less wear in comparision to uncoated friction damper. Wear behaviour in coated and uncoated damper is different at room temperature and at elevated temperature.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

The diameter of a H13 steel tool with M6 threads and a pin diameter of 5.9 mm and a pin length of 5 mm was measured after each 25.4 mm length of friction stir processing (FSP) of 6061-T6 extrusions. The change in pin diameter with FSP time or distance did not exhibit any steady state and was found to have two distinct regions. Metallographic analysis of two tools subjected to FSP for 60 and 120 seconds showed that (i) threads fractured in early stages of FSP, (ii) a built-up layer formed between the threads, and (iii) threads progressively wore with processing time. The metallographic analysis of an embedded tool showed the presence of a fractured piece of the tool in the stir zone. These points are discussed in detail in the paper.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

Average of 41,900 patients are diagnosed annually with staphylococcus bacterial infection in California, 24,089 patients have Methicillin-resistant Staphylococcus Aureus (MRSA) and 17,810 patients have Methicillin-Sensitive Staphylococcus (MSSA). This paper demonstrates that there is a difference in mortality rate due to staphylococcus infection between males and females (P-value<0.05, CI 95%). Male patient diagnosed with S. aureus has 1.3 chance of mortality incidence than female patient. In addition, MRSA infection rate is 1.4 times MSSA infection (P-value<0.05, CI 95%), but the gap of infection is decreasing; however, mortality of both infections combined are more than threefold greater compared to three decades ago.

Carbapenem resistant Enterobacteriaceae (CRE) has been public health risk in several countries and recent reports indicate the emergence of CRE in food animals. This study was conducted to investigate the occurrence, resistance patterns, and phylogenetic diversity of CRE E.coli from chicken. Routine bacteriology, PCR detection of E.coli species, multiplex PCR to detect carbapenemase encoding genes and phylogeny of CRE E. coli were conducted. The results show that 24.36 % (19/78) were identified as CRE based on the phenotypic identifications of which 17 were positive for the tested carabanemase genes. The majority, 57.99% (11/19) of the isolates harbored multiple carbapenemase genes. Four isolates harbored all blaNDM blaOXA, blaIMP, five and two different isolates harbored blaNDM and blaOXA, and blaOXA and blaIMP respectively. The Meropenem, Imipenem and Ertapenem MIC values for the isolates ranged from 2g/mL to ≥256g/mL. Phylogenetic grouping showed that the CRE E.coli isolates belonged to five different groups; groups A, B1, C, D and unknown. The detection of carbapenem resistant E.coli in this study shows that CRE is has become an emerging problem in farm animals, particularly, in poultry farms. This also implies the potential public health risks posed by CRE from chicken to the consumers.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

This article focuses on the issue of motor oils used in the engines of off-road mobile machinery (NRMM), more specifically tractors. The primary goal of the paper is to determine the appropriate replacement interval for these oils. The physical properties of the examined samples were first determined by conventional instruments. Furthermore, the concentration of abrasive metals, contaminants, and additive elements were measured using an optical emission spectrometer. Lastly, the content of water, fuel, glycol, and the products of oxidation, nitration, and sulphation were determined by using infrared spectrometry. The measured values were compared to the limit values. Based on the processing and evaluation of these analyses, the overall condition of the oils was assessed and subsequently the optimal exchange interval of the examined oils was determined. In addition, a risk analysis of the outage was performed. Due to the high yields of crops, farmers can lose a significant amount of product when a tractor is not functioning during the harvest period. This loss for calculated in the paper.

Staphylococcus aureus (S. aureus), particularly Methicillin-resistant S. aureus (MRSA), is a life-threatening pathogen that causes a variety of infections in hospital and community settings. It poses a significant risk and challenge for global health that hinders our ability to control and treat bacterial infections. Recently, the emergence and spread of variant strains of bacteria, misuse of the limited available options of effective antibiotics, spread of fake drugs, and climate change that increased the contact between humans and animals’ populations carrying different bacterial has significantly increased the incidence of Multi-Drug Resistance strains (MDR). This in turn, has created a severe problem in the infection control treatment of S. aureus infected patients. Treatment options for MRSA infection are increasingly limited and complicated. Unfortunately, different strains of MRSA are showing tolerance and resistance toward vancomycin, which is the standard of care for complicated MRSA. Therefore, it is crucial now to invest developing new effective anti-biotics and synergies, develop and implement national action plans for the management of an-tibiotic resistance, as well as improving our understanding of the antimicrobial resistance mechanisms. Here, in this review we explain the main mechanisms of antibiotic resistance in MRSA and describes different approaches to manipulate it in MRSA, providing a basis for de-signing effective drugs, and shedding some light on the evolution of S. aureus.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the effect of CrAlSiN thin-film PVD-deposition on the tribological behaviour of tool steel K340. The sliding wear performance of the coated K340 steel is analysed in relation to both the uncoated K340 steel and a range of tool steels dedicated to hot- and cold-working, such as X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with a CrAlSiN hard film (K340/CrAlSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/CrAlSiN are examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction are estimated and analysed with respect to hardness and alloying composition of the materials under study. SEM observations are made to identify the sliding wear mechanisms of the analysed tool steels and PVD-coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K304 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K304/CrAlSiN sample has a COF of 0.529 and a wear factor of K=5.68×10−7 m3 N−1 m−1, while the COF of the reference tool steels ranges from 0.702 to 0.885 and their wear factor ranges from 1.68×10−5 m3 N−1 m−1 to 3.67×10−5 m3 N−1 m−1. The CrAlSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

We previously described a model of deep intrinsic resistance of breast cancer wherein we used a function-based approach to selection of cancer cells that can survive a variety of challenges in prolonged but reversible quiescence. Our experimental results suggested that resistant cancer cells possess a variety of mechanisms, including modifications of the epigenome and transcriptome, for generating a high degree of cellular heterogeneity. In the present study, we evaluated JIB-04, a small-molecule epigenetic inhibitor initially discovered to inhibit cancer growth, to determine its ability to affect deep intrinsic resistance in our breast cancer model. We found that long pretreatment with JIB-04 sensitized resistant triple-negative inflammatory breast cancer cells and their parental cell line SUM149 to the chemotherapeutic drugs doxorubicin and paclitaxel. Resistant cancer cells derived from another inflammatory breast cancer cell line, FC-IBC02, were considerably more sensitive to JIB-04 than was the parental cell line. Investigating a mechanism of sensitization, we found that JIB-04 exposure increased the expression of PD-L1 in resistant cells, suggesting that JIB-04 may also sensitize resistant breast cancer cells to anti-PD-L1 immune therapy. Finally, these results support the usefulness of our experimental strategy for evaluating anticancer agents such as JIB-04 that may halt cancer evolution and prevent development of cancer resistance to currently used therapies.

For many years, the programmable positioners have been widely applied in structures of modern electro-pneumatic final control elements. The positioner consists of an electro-pneumatic transducer, embedded controller and measuring instrumentation. Electro-pneumatic transducers that are used in positioners are characterized by a relatively short mean time-to-failure. The practical and economical method of a reasonable prolongation of this time is proposed in this paper. It is principally based on assessment and minimizing the effort of the embedded controller. For this purpose, were introduced: the control value variability, mean-time and the cumulative controller's effort. The diminishing of controller effort has significant practical repercussions, because it reduces the intensity of mechanical wear of the final control element components. On the other hand, the reduction of the cumulative effort is important in the context of process economy due to limitation of the consumption of energy of compressed air supplying the final control element. Therefore, the minimization of introduced effort factors has an impact on increasing the functional safety and economics of the controlled process. As a result of the performed simulations, the recommendations regarding the selection of the structure and tuning of positioner controller were elaborated. The simulations were performed in the Matlab-Simulink environment with the use of the liquid level control system in which a phenomenological model of a final control element was deployed. It has been proven that under appropriate conditions, it is possible to extend significantly the lifetime of the final control element and simultaneously enhance the control quality factors.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

Neuroendocrine neoplasms (NENs) comprise a heterogeneous group of rare malignancies mainly originated from hormones secreting cells, which are widespread in human tissues. The identification of mutations in ATRX/DAXX genes in sporadic NENs, as well as the high burden of mutations scattered throughout MEN-1 gene in both sporadic and inherited syndromes, provided new insights into the molecular biology of tumour development. Other molecular mechanisms, such as the NOTCH signaling pathway, have shown to play an important role in the pathogenesis of NENs. NOTCH receptors are expressed on neuroendocrine cells and generally, act as tumour suppressor proteins, but in some contexts can function as oncogenes. The biological heterogeneity of NENs suggests that to fully understand the roles and the potential therapeutic implications of gene mutations and NOTCH signaling in NENs, a comprehensive analysis of genetic alterations, NOTCH expression patterns and their potential roles across all NEN subtypes is required.

Staphylococcus aureus (S. aureus) is a major human pathogen that requires new antibiotics with unique mechanism. A new pleuromutilin derivative, 14-O-[(4,6-Diaminopyrimidine-2-yl) thioacetyl] mutilin (DPTM), has been synthesized and proved as a potent antibacterial agent using in vitro and in vivo assays. In the present study, DPTM was further in vitro evaluated against Methicillin-resistant Staphylococcus aureus (MRSA) isolated from dairy farms and outperformed tiamulin fumarate, a pleuromutilin drug used for veterinary. Moreover, a murine skin wound model caused by MRSA infection was established and the healing effect of DPTM was investigated. The results showed that DPTM could promote the healing of MRSA skin infection, reduce the bacterial burden of infected skin MRSA and decrease the secretion of IL-6 and TNF-α inflammatory cytokines in plasma. These results provided the basis for further in-depth drug targeted studies of DPTM as a novel antibacterial agent.

Background: Diabetic foot ulcers are an increasingly common complex problem and are associated with a very considerable health care burden. Diabetic foot ulcer with Alcaligenes faecalis infection is rarely reported in the literature. We report a case series of diabetic foot ulcer with Alcaligenes faecalis infection treated at our facility. Methods: We conducted a retrospective analysis of all patients with diabetic foot ulcer with Alcaligenes faecalis infection seen from January 2014 to April 2019. We analyzed the clinical characteristics, ulcer lesion classification, comorbidities, prior intravenous antibiotic use within three months, wound culture, antibiotics sensitivity test, and clinical outcomes of these patients. Results: Eight cases of diabetic foot ulcer with Alcaligenes faecalis infection were seen in five males and three females. The mean age was 54.6 years. All patients had other comorbidities, and all ulcer lesions were of chronic duration ( more than 14 days ). All wound cultures revealed polymicrobial infection, with two cases of diabetic foot with extensive-drug resistant Alcaligenes faecalis infection found in 2019. All patients needed intravenous antibiotic therapy and surgical interventions for the chronic ulcer lesion. The wound failed to heal in three patients. Conclusions: All diabetic foot ulcers with Alcaligenes faecalis infection were of chronic duration ( more than 14 days ) and had polymicrobial infection. Extensive-drug resistant Alcaligenes faecalis emerged in 2019. Definitive antibiotic therapy is necessary for all infected wounds and should be based on both the culture results and susceptibility data. All patients will need appropriate wound care, and most will need rapid surgical intervention for an optimal outcome.

Comminution is a very important and result-determining step in mineral processing. This is because further downstream processes in the beneficiation chain depend entirely on it. Comminution includes the blasting, crushing, and grinding of ore to liberate valuable mineral particles. It consumes most of the energy used in mineral processing plants with grinding using up to 50% of the provided energy. Tumbling mills are an old technology that is still commonly used for grinding. One of the most used tumbling mills is the ball mill. This paper reviews different types of grinding media that have been developed and improved over the years and their properties. Also reviewed are the effects of grinding media on various aspects such as energy consumption, mill efficiency, minerals liberation and grinding rate. A comparison of the grinding media is given together with the knowledge gaps that still need to be bridged to improve the quality and performance of grinding media used in ball mills. Despite various research conducted on ball mills, the grinding process is still a very energy inefficient process. This creates a great opportunity for further research to improve the process because just a slight improvement in the process efficiency significantly reduces the production costs and provides a lot of environmental benefits.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Understanding of the molecular mechanisms of prostate cancer has led to development of therapeutic strategies targeting androgen receptor (AR). These androgen-receptor signaling inhibitors (ARSI) include androgen synthesis inhibitor- abiraterone and androgen receptor antagonists- enzalutamide, apalutamide, and darolutamide. Although these medications provide significant improvement in survival among men with prostate cancer, drug resistance develops in nearly all patients with time. This could be through androgen-dependent or androgen-independent mechanisms. Even weaker signals and non-canonical steroid ligands can activate AR in the presence of truncated AR-splice variants, AR overexpression, or activating mutations in AR. AR splice variant, AR-V7 is the most studied among these and is not targeted by available ARSIs. Non-androgen receptor dependent resistance mechanisms are mediated by activation of an alternative signaling pathway when AR is inhibited. DNA repair pathway, PI3K/AKT/mTOR pathway, BRAF-MAPK and Wnt signaling pathway and activation by glucocorticoid receptors can restore downstream signaling in prostate cancer by alternative proteins. Multiple clinical trials are underway exploring therapeutic strategies to overcome these resistance mechanisms.

In the process of metal cutting, the anti-wear performance of the tool determines the life of the tool and affects the surface quality of the workpiece. The finite element simulation method can directly show the tool wear state and morphology, but due to the limitations of the simulation time and complex boundary conditions, it has not been commonly used in tool life prediction. Based on this, a tool wear model was established on the platform of a finite element simulation software for the cutting process of titanium alloy TC4 by end milling. The key technique is to embed different types of tool wear models into the finite element model in combination with the consequent development technology. The effectiveness of the tool wear model is validated by comparing the experimental results with the simulation results. At the same time, in order to quickly predict the tool life, an empirical prediction formula of tool wear was established, and the change course of tool wear under time change was obtained.

The structural and strength analysis of the material used to construct such an important engine element as the turbine is of great significance, both at the design stage as well as during tests and expertises related to emergency situations. Bearing in mind the conditions above mentioned, the paper presents the results of research on the chemical composition, morphology and phased structure of the metallic construction material used to produce the blades of the high and low pressure turbine of the RD-33 jet engine, which is the propulsion unit of the MiG-29 aircraft. The data obtained as a result of the material tests of the blades allowed, on the basis of the analysis of chemical composition and phased structure, to determine the grade of the alloy used to construct the tested elements of the jet engine turbine. The structural stability of the material was found to be lower in comparison with engine operating conditions, which manifested itself as a clear decrease in the resistance properties of the blade material. The results obtained can be used as a basis for analyzing the life span of an object or a selection of material replacements, which enable to produce the analyzed engine element.

Acinetobacter baumannii is a multidrug-resistant and invasive pathogen associated with the etiopathology of both an increasing number of nosocomial infections and of relevance to poultry production systems. Multidrug-resistant Acinetobacter baumannii has been reported in connection to severe challenges to clinical treatment, mostly due to an increase rate of resistance to carbapenems. Amid the possible strategies aiming to reduce the insurgence of antimicrobial resistance, phage therapy has gained particular importance for the treatment of bacterial infections. This review summarises the different phage-therapy approaches currently in use for multiple-drug resistant Acinetobacter baumannii, including single phage therapy, phage cocktails, phage -antibiotic combination therapy, phage coding Acinetobacter baumannii and the novel phage enzyme treatment. Although phage therapy represents a potential treatment solution for multidrug-resistant Acinetobacter baumannii, further research is needed to unravel some unanswered questions especially in regard to its in vivo applications, before possible routine clinical use.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

TThe paper presents the results of research on the influence of the settings of lubrication and cooling system parameters (solenoid valve opening time and lubricant feed pressure in terms of its quantity) in order to select the optimal lubricating conditions and thus reduce the wear of the dies used in the first forging operation of the valve forging made of high-nickel steel. Based on the observation of lubrication in the industrial process, it was found that a significant part of the lubricant fails to reach the die cavity, reaching the outside of it, which causes die wear due to seizure resulting from adhesion of the forging material to the tool surface, as well as high lubricant consumption and dirt in the press chamber. The authors proposed their own mobile lubricating and cooling system, which allows for a wide range of adjustments and provided with automatic cleaning procedures of the entire system, unlike the fixed lubrication system used so far in the industrial process. First, tests were carried out in laboratory conditions to determine the highest wettability and the lubricant remaining inside the tool cavity. These tests determined the lubrication system parameter settings which ensured that the greatest amount of lubricant remains in the cold die cavity without the forging process. Then, to verify the obtained results, tests were carried out in the industrial process of hot die forging of valve forgings, for short production runs of up to 500 forgings. The results were compared with the measurement of changes in the geometry of tools and forgings based on 3D scanning and surface topography analysis with the use of SEM. For best results (the variant of the setting of the dose and the time of exposure to lubricant), the forging process was carried out with the use of a new tool, up to the maximum service life.

The global spread of multidrug-resistant (MDR) microbial infections is currently one of the most severe risks to global public health, with 10 million fatalities expected by 2050 unless action is taken. Nanotechnology has revolutionized science and medicine. The reliance on nanotechnology is growing. Nanoparticles have distinct properties that improve biological, chemical, and physical properties studied for various uses. A significant area of attention in the synthesis of nanoscale modulators is the utilization of crude formulations, retro-synthesized, and pure chemicals, mainly from herbal sources, with fewer adverse effects. Green chemistry has devised a tangential technique for synthesizing metals and metal oxides to produce nanoparticles. Plant extracts (leaves, stems, and shoots) and microorganisms (bacteria, fungus, and yeast) are used as reducing intermediates to make nanoparticles. Studies in microbiology have shown that nanoparticles kill bacteria, fungi, viruses, and protozoa. These green nanoparticles contain antibacterial, antifungal, and anti-inflammatory effects. Most nanoparticles have high antibacterial properties, indicating they may be used to combat diseases and biological contaminants. These nanoparticles have antibacterial action against pathogenic microorganisms that cause serious illnesses, including multidrug-resistant pathogens. The current research will pave the way for future applications and improved methods for producing nanoparticles, paving the way for an innovative route in nano-life sciences with widespread recognition.

Due to slow progression and susceptibility to radical forms of treatment low-grade PC is associ-ated with high overall survival (OS). With the clinical progression of PC the therapy is getting more complex. The immunosuppressive tumor microenvironment (TME) makes PC a difficult target for most immunotherapeutics. Its general immune resistance is established by i.e. immune evasion through Treg cells, synthesis of immunosuppressive mediators, and defective expression of surface neoantigens. The success of sipuleucel-T in clinical trials initiated several other clinical studies that specifically target the immune escape of the tumor and eliminate the immunosuppres-sive properties of TME. In the settings of PC treatment, this can be commonly achieved with radi-ation therapy (RT). Also, focal therapies usually applied for localized PC, such as high-intensity focused ultrasound (HIFU) therapy, cryotherapy, photodynamic therapy (PDT), or irreversible electroporation (IRE) were shown to boost anti-cancer response. Nevertheless, the present guide-lines restrict their application to localized and low-grade PC. This review explains how RT and focal therapies enhance the immune response. We also provide data supporting the combination of RT and focal treatments with immune therapies.

Urinary tract infections (UTIs) caused by pathogens, particularly E. coli, have spontaneously become resistant to antimicrobial drugs in recent years. Therefore, regular monitoring and alternative strategies for the antimicrobial agent are crucial for combating antimicrobial resistance and bacterial biofilms. Here, we report a new cobalt iron oxide-conjugated tin oxide nanocomposite that can kill bacteria and treat multidrug-resistant E. coli posing UTIs. Following the isolation and identification of E. coli, we tested 57/134 samples against sixteen commonly used antibiotics phenotypically using the disk diffusion method to determine their sensitivity pattern. Of the 57 E. coli isolates, 66% (38/57) were multidrug-resistant. The E. coli isolates were resistant to cephradine (70.17%), ceftriaxone (59.64%), and azithromycin (59.64%), followed by cefixime (54.38%), cefuroxime sodium (52.63%), and co-trimoxazole (50.87%). X-ray diffraction results showed the crystallite sizes were about 5.68 and 8.84 nm in pure SnO2 nanoparticles and 95% SnO2-5% CoFe2O4 nanocomposite, respectively. Energy-dispersive X-ray spectroscopy and Fourier transform infrared determined the fundamental structure of the nanocomposite, encompassing Co, Fe, Sn, and O. Moreover, FTIR measurements implied that the distinct functional groups in both SnO2 and CoFe2O4 nanoparticles existed in a 95% SnO2-5% CoFe2O4 nanocomposite. Field emission scanning electron microscope analysis uncovered that the SnO2-CoFe2O4 nanocomposite had a size of roughly 24 nm and was spherical. In addition, the biosynthesized SnO2 nanoparticles and SnO2-CoFe2O4 nanocomposite were evaluated for their antibacterial activity. At a minimum 100 µg/mL concentration, SnO2 nanoparticles and SnO2-CoFe2O4 nanocomposite showed high antibacterial activity. The SnO2 nanoparticles and SnO2-CoFe2O4 nanocomposite demonstrated antibacterial activity on multidrug-resistant E. coli at 10 ± 0.7 and 16 ± 0.8 mm zone of inhibition, respectively. In conclusion, the new SnO2-CoFe2O4 nanocomposite might be a potential candidate for treating UTIs caused by drug-resistant E. coli in the foreseeable future.

The increased emergence of multidrug-resistant Helicobacter pylori influences the prevention of stomach cancer. Zingiber officinale is a plant usually used in folk medicine to treat a variety of diseases involving infections, nausea, vomiting, peptic ulcer, dyspepsia, and inflammation. This study was conducted to evaluate the ability of Z. officinale extract to combat resistant H. pylori. The disc diffusion, microdilution, and microplate assays were performed to evaluate the susceptibility to antibiotics, and the antibacterial and antibiofilm activities of the Z. officinale extracts. Using the checkerboard method, the combined effects of the gentamicin and Z. officinale extract were investigated. In addition, anti-inflammatory activity and GC-MS analysis were determined by the modified protocol. According to the findings, H. pylori isolates exhibited resistance rates of 56.33, 50.0, and 45.85 for metronidazole, gentamicin, and tetracycline, respectively. The methanolic extract of Z. officinale had the strongest effectiveness against resistant H. pylori isolates with MIC of 20.0 to 50.0 µg/ml against both H. pylori isolates and the stranded strain NCTC 11637. Z. officinale extract suppress the biofilm formed by H. pylori isolates with a percentage of 92.96% at 50.0µg/ml, compared with 97.19% for gentamicin at the same concentration. According to FICI values, combination of methanolic Z. officinale extract to gentamicin increases bacterial sensitivity to such drugs. Moreover, the Z. officinale extract exhibits strong anti-inflammatory activity. The GC-MS analysis of Z. officinale extract exhibits 17 different chemical compounds. Conclusions: The Z. officinale extract contain the anti-inflammatory compound gingerol as the main constituent which inhibits the growth of H. pylori and its biofilm, are a promising natural therapeutic alternative or enhance antibiotics activity

Erosion caused by the repeated impact of particles on a substance surface is a usual wear method resulting in gradual and continual loss of objects. It is a crucial problem in several modern industries because their surfaces are frequently subjected to destructive erosive situations. Polymers and their hybrid materials include several applications to be used as a coating in the form of powder for different applications. This review paper aims to provide extensive information on the erosion behavior of thermoset and thermoplastic neat resin and their hybrid materials composites. Focus is specifically paid to highlight the influence of properties of selected materials, impingnation parameters such as incident Angle of erodent, impact velocity of erodent, erodent nature, and the erosion mechanism. The review further extends the information about the erosion techniques and numerical simulation methods used for wear studies of surfaces. An investigation has been carried out for researchers to explore the selection of materials and methods in terms of conditions and parameters to meet the current and future needs and challenges for the protection of surfaces of the advanced industries. During review according to the findings achieved from the literature of the past fifty years, it has been noted that the thermoplastic nature of the composite is a key component to determine the anti-wear properties, the composites with lower glass transition, higher ductility, and greater crystallinity can provide better protection to erosion in advance surface applications.

Background: Combinatorial therapy- “nano antibiotics” is an emerging field in nanoscience. In this present investigation, we attempted to combine the green synthesized noble metal nanoparticle and the antibiotic Streptomycin to form bio-conjugated nanoparticles. The newly synthesized Nano antibiotics acted as the antibiotic carrier, functioned as cargo, and delivered the antibiotic. Methods: Comparative studies between the noble metal nanoparticles were attempted for the first time on the grounds of their antibacterial activity. The antibacterial activity of the three noble metal nanoparticles was assessed against Streptomycin-resistant Bacillus sp.; the results obtained proved that silver nanoparticles were a potent antibacterial agent. Still, no antibacterial activity was exerted by gold, and platinum nanoparticles were for the Streptomycin-resistant strain Bacillus sp. To our surprise, the gold and platinum fabricated/bio-conjugated nanoparticle with the antibiotic showed 100% antibacterial activity, whose antibacterial activity was zero when functioning as a nanoparticle alone. Results: The combinatorial therapy of two different clauses of drugs majorly increased antibacterial activity. It enhanced the antibiotic to overcome the resistance exhibited by the bacterial pathogen, and the possible mechanism is elucidated in the present study. Also, an attempt has been made to assess the nanotoxicity of the nano-bioconjugates on RBC and compare their hemocompatibility. The results obtained in the current investigation demonstrate the enhanced antibacterial activity of the green synthesized nanoparticles conjugated with the streptomycin; their efficacy for combinational therapy against resistance in pathogenic organisms highlights the novelty of the work and the comparative study of three different noble metals nanoparticles (Ag, Au, Pt) from single agro-waste for the first time.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

This study presents the computational model to determine the wear behaviour of polymer gears. Using PrePoMax finite element numerical calculation software, a proposed computational model was built to predict wear behaviour based on Archard's wear model. This allows the calculation of the wear depth in each loading cycle with constant mesh updating. The developed computational model has been evaluated on the spur gear pair, where the pinion made of POM has meshed with a support gear made of steel. The computational results that were obtained were compared with the analytical results according to the VDI 2736 guidelines. Based on this comparison, it was concluded that the proposed computational model could be used to simulate the wear behaviour of contacting mechanical elements like gears, bearings, etc. The main advantage of the model, if compared to the standardised procedure according to the VDI 2736 guidelines, is the geometry updating after a chosen number of loading cycles, which enables a more accurate prediction of wear behaviour under rolling/sliding loading conditions.

Environment approachable products such as fuels and lubricants are among the best choices in several countries that contain renewable products as alternatives. To protect human life, alternative methods of saving the environment and production balance is needed to reduce the effects of the crisis and the contamination of the Environment. This research concentrated on the Manufacturing and testing of bio- grease from sugar cane filter mud vegetable oil as a lubricant for friction reduction and determining the properties of both bio grease and Mineral oil grease with environmental problems. SC filter mud oil as an alternative use for bio-grease preparation in addition to mineral oil grease. The Testing was accepted to determine the quality of the eco-friendly grease produced. For the preparation of this bio- grease, the SC Filter cake sample is taken from different sugar factory which found in Ethiopia. The sample has a moisture content of 78%. Using this sample first oil is extracted by Soxhlet apparatus, n-hexane solvent and temperature for extraction from 42 -68℃. The maximum temperature and time for extraction of oil were 68 and 7hrs respectively. The extracted oil's physical properties include color, acid value, specific graphite, saponification value, iodine value, density, and viscosity. Finally, the friction behavior in function of time for both grease at identical load, the friction coefficient vs time for SC filter Cake Grease_ Na_ MoS2 and industrial mineral one (I_ Greasily _ MoS2), grease was determined.

Vancomisin resistant enterococcus(VRE), is a resistant microorganism which colonizates and causes infections in hospitalized patients. It was aimed to show the spread of vancomycin-resistant Enterococcus (fVREfm) step-by-step in all intensive care units, which started with the growth of vancomycin-resistant Enterococcus faecium (VREfm) on 02.12.2021 in the blood culture of a patient hospitalized in the anesthesia intensive care unit of our hospital and was found to have reached epidemic size in the surveys. Rectal swab samples were taken from all patients hospitalized in intensive care units, VRE colonization was determined and the VanA and VanB resistance genes associated with vancomycin resistance of VREfm isolates were determined by PCR method, and clonal association analysis was performed by Arbitrarily Primed-PCR (AP-PCR) and Pulsed-Field Gel Electrophoresis. In our study, VRE was detected in 61 of 2601 rectal swab samples. 54 (85.52%) of the VRE isolates were Enterococcus faecium, 3 (4.91%) was Enterococcus faecalis, 3 (4.91%) was Enterococcus gallinorum, 1 (1.63%) was Enterococcus casseliflavus. It was determined that all of the 54 VREfm isolates, which were the most detected among all VRE isolates, carried the vanA gene. In the clonal association analysis of the isolates by AP-PCR and PFGE methods, it was found that they had 12 different genotypes, 48 of them were included in any cluster, the clustering rate was 88.8%, and the largest cluster was genotype 1 cluster with 36 isolates. Of the 54 patients with VREfm isolated recently, 18.51 percent of the clinical samples were isolated before the survey, and 9.24% were isolated after the survey. It was determined that 100% of VREfm isolates were resistant to ampicillin, levofloxacin, ciprofloxacin, high-level gentamicin, trimethoprim-sulfamethoxazole, teicoplanin, 7.4% to tigecycline and 1.85% to linezolid. In our study, in the clonal association analysis performed by isolating VREfm in rectal swab samples, it was found that 88.8% of the samples were indistinguishably similar and the increase in the number of VREfm infections after the index case in our hospital was associated with the epidemic. VREfm infections cause long term hospitalization, costs and also deaths, which shows the seriousness of the event, and the importance of the combination of epidemiological and molecular analysis in epidemic research.

Due to the rapid emergence of multi drug resistant (MDR) pathogens against which current an-tibiotics are no longer functioning, severe infections are becoming practically untreatable. Con-sequently, the discovering of new classes of effective antimicrobial agents with novel modes of action is becoming increasingly urgent. The bioactivity of Cannabis sativa, an herbaceous plant used for millennia for medicinal and recreational purposes, is mainly due to its content in phytocan-nabinoids (PCs). Among the 180 PCs detected, cannabidiol (CBD), Δ8 and Δ9-tetrahydrocannabinols (Δ8-THC and Δ9-THC), cannabichromene (CBC), cannabigerol (CBG), cannabinol (CBN) and some their acidic precursors have demonstrated from moderate to potent antibacterial effects against Gram-positive bacteria (MICs 0.5–8 µg/mL), including methicillin-resistant Staphylococcus aureus (MRSA), epidemic MRSA (EMRSA), as well as fluoroquinolones and tetracycline-resistant strains. Particularly, the not psychotropic CBG was also capable to inhibit MRSA biofilm formation, to eradicate that mature, and to rapidly exterminate MRSA persiters cells. On this scenario, CBG, as well as other minor not psychotropic PCs, such as CBD, and CBC could represent promising compounds for developing novel antibiotics with high therapeutic potential. Anyway, further studies are necessary, needing abundant quantities of such PCs, scarcely provided naturally by Cannabis plants. Here, after an extensive overture on cannabinoids including their reported an-timicrobial effects, aiming at easing the synthetic production of the necessary amounts of CBG, CBC and CBD for further studies, we have, for the first time, systematically reviewed the synthetic pathways utilized for their synthesis, reporting both reaction schemes and experimental details.

The calculation of the collapse load of spherical domes is addressed using a semi-analytical approach under the hypotheses of small displacements and perfect plasticity. The procedure is based on the numerical approximation of the self-stress that represents the projection of the balance equilibrium null space on a finite dimensional manifold. The so obtained self-equilibrated stress span is superimposed to a finite element linear elastic solution to the prescribed loads yielding to the statically admissible set accordingly to Melan’s theorem. The compatibility of the stress with the constitutive law of the material has been enforced using linearized limit domain in terms of generalized stress, namely axial force and bending moment along the local spherical curvilinear coordinates. The procedure has been tested with reference to numerical and experimental data from the literature confirming the accuracy of the proposed method. The comparison with the literature confirms that the buckling load is much greater than the plastic collapse loads both calculated through the proposed procedure and reported in the quoted literature.

BMAP-18, derived from the N-terminal region of bovine myeloid antimicrobial peptide BMAP-27, demonstrated potent antimicrobial activity without cytotoxicity. This study aimed to compare the antibacterial, antibiofilm, and anti-inflammatory properties of BMAP-18, rich in aromatic phenylalanine residues, with its aliphatic analogue, BMAP-18-FL. Both aromatic BMAP-18 and aliphatic BMAP-18-FL exhibited equally potent antimicrobial activities against Gram-positive and Gram-negative bacteria, particularly methicillin-resistant Staphylococcus aureus (MRSA) and multidrug-resistant Pseudomonas aeruginosa (MDRPA). Mechanistic investigations employing SYTOX green uptake, DNA binding, and FACScan analysis revealed that both peptides acted by inducing membrane permeabilization and subsequent intracellular targeting. Moreover, both BMAP-18 and BMAP-18-FL effectively prevented biofilm formation and eradicated existing biofilms of MRSA and MDRPA. Notably, BMAP-18-FL displayed superior anti-inflammatory activity compared to BMAP-18, significantly reducing the expression levels of pro-inflammatory cytokines in lipopolysaccharide-stimulated macrophages. This study emphasizes the similarities and differences in the antimicrobial, antibiofilm, and anti-inflammatory properties between aromatic BMAP-18 and aliphatic BMAP-18-FL, providing valuable insights for the development of multifunctional antimicrobial peptides against drug-resistant bacteria.

Seed germination and seedling growth represent two vulnerable stages in a plant life cycle and it is important to determine how they will be affected by environmental changes associated with climate change. This study examines the impact of salinity levels (0, 50, 100, and 150 mM) at each of three temperatures (15, 25, and 35˚C) on seed germination and radicle growth for three dormant and three non-dormant varieties of conventional, glyphosate resistant, or reduced lignin alfalfa. The genetic basis and phenotypic plasticity for seed germination and seedling growth in response to salinity and temperature were determined. Both traits were phenotypically plastic with respect to temperature and salinity. Seed germination was 87.0% ± 1.7 at 25˚C, 0mM (no salinity), but decreased to 33.9% ± 3.9 germination at 35˚C and 150mM. Radicle length went from 36.7 ± 1.5 mm after four days at 25˚C, 0mM, to 10.5 ± 0.7 mm at 35˚C, 150mM. The phenotypic response brought seed germination and radicle length away from their optimum, but we detected standing genetic variation for both seed germination and radicle length. Selection to increase both traits at high temperature and salinity would facilitate alfalfa establishment under climate change.