This paper proposes the use of non-uniform extended surfaces installed externally to the tubes of the radiation section of fired heaters, in order to obtain a better heat flux distribution to the coils. To this end, the heat transfer mechanisms present in such equipment were studied through computational fluid dynamics (CFD), using simplified geometries that represent typical sizes of fired heaters. Also, a simplified model for the combustion was considered. Although this model oversimplifies the physics of the problem, it was able to give satisfactory results for the parameters being optimized, considering the main objective of this paper, that is to minimize the non-uniformity of heat flux in the tubes of the radiant section of fired heaters. It was possible to obtain optimized geometric parameters for different types of extended surfaces evaluated, coupling the results of these models with the Particle Swarm optimization method through the use of a response surface technique,. The results indicate a significant improvement in the uniformity of the heat flux distribution to the tubes through the use of the proposed extended surfaces. Thus, this solution reveals to be an interesting alternative to reduce the risks of fluid degradation and coking formation. Future studies must investigate the non-uniformity of the heat flux due to the presence of the flame and consider the interaction between the reactive flow and the participating medium. Nevertheless, this paper presents some results that justify the optimization of such extended surfaces taking into consideration thermal radiation.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

A close-range photogrammetric approach and its implementation using a CNC device and a macro camera are proposed. A tailored image acquisition approach is proposed that is implemented using this device. To increase reconstruction robustness and accuracy, the key point features detected in the acquired images are tracked across multiple views from multiple viewpoints at multiple distances. This approach reduces spurious correspondences and, as a result, the estimation accuracy of calibration parameters is increased and reconstruction errors are reduced. Qualitative and quantitative evaluation demonstrate the efficacy and accuracy of the proposed approach, which exhibits micrometre resolution and low implementation cost.

Diabetes is a prevalent global health issue associated with significant morbidity and mortality. Diabetic retinopathy (DR) is a well-known inflammatory, neurovascular complication of diabetes and a leading cause of preventable blindness in developed countries among working-age adults. However, the ocular surface components of diabetic eyes are also at risk of damage due to uncontrolled diabetes, which is often overlooked. Inflammatory changes in the corneas of diabetic patients indicate that inflammation plays a significant role in diabetic complications, much like in DR. The eye´s immune privilege restricts immune and inflammatory responses, and the cornea and retina have a complex network of innate immune cells that maintain immune homeostasis. Nevertheless, low-grade inflammation in diabetes contributes to immune dysregulation. This article aims to provide an overview and discussion of how diabetes affects the ocular immune system’s main components, immune-competent cells, and inflammatory mediators. By understanding these effects, potential interventions and treatments may be developed to improve the ocular health of diabetic patients.

Titanium (Ti) and Ti-based alloys are commonly used in dental implants, and surface modifications of dental implants are important for achieving osseointegration (i.e., direct connection between the implant surface and bone). This study investigated the effect of an eco-friendly etching solution—a hydrogen peroxide–sodium bicarbonate mixture—on the surface properties and contact angles of and osteoblast adhesion and proliferation on Ti surfaces. Disk-shaped Ti specimens were prepared using different surface treatments (machining, sandblasting, and sandblasting/acid-etching), and they were immersed in the etching solution and then ultrasonically cleaned. Surface characterization was performed using scanning electron microscopy, digital microscopy, contact angle analysis, and X-ray photoelectron spectroscopy. MG-63 osteoblasts were cultured on the specimens, and their adhesion to the specimen surface and their proliferation were examined using staining and the MTT assay, respectively. Additional etching with the etching solution caused the formation of nano/micro hierarchical structures, increased the surface roughness, and enhanced the hydrophilicity. Osteoblast adhesion and proliferation were found to improve on the modified surfaces. The eco-friendly etching method has the potential to enhance the biological properties of Ti implant surfaces and to thereby improve the dental implant performance.

The access road to the powerhouse's hydraulic system's facilities in Guarumales (Azuay, Ecuador) presents a medium-sized landslide. Geophysical tests were conducted in the initial research stage, combining electrical and seismic methods. A SEV and HVSR surveys campaign have been taken as a reference for the analysis of the landslide area. The distribution of these test points has been at three different levels along the landslide where the access road crosses it and trying to cover the area's most extensive possible length and width. In the area, we find the geology dominated by the presence of schists, altered to different degrees and presenting blocks of material with a lower degree of alteration within colluvium formed by a clayey matrix and coarse material of the exact nature. There is also evidence of surface and groundwater in the area. The results obtained through SEV tests have allowed for defining the separation zone of the mobilized or sliding materials compared to the fixed or immobile ones (potentially, the sliding surface was marked). Using the HVSR technique, the natural vibration frequencies of the ground associated with the sliding mass (separation of seismic impedances between a two-layer model: mobile and fixed) have been determined. Previous authors proposed an empirical relationship establishing the exponential relationship, already proposed by previous authors, between sediment thickness and natural frequencies. It has been possible to determine the depth of the position of the loosely compacted sediment zone (and probably moving or mobilized) compared to that of compact materials (immobile) and thereby define the potential rupture surface.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

Extracellular enzymes catalyze biogeochemical reactions in soil, cycling carbon and nutrients in agricultural systems. Enzymes respond quickly to soil management, including organic amendment inputs, such as biochar, a charcoal-like solid byproduct of bioenergy production. In a previous agricultural field trial, a pine biochar amendment caused an approximately 40% decrease in the enzyme activities of β-glucosidase (BG) and phosphatase (PHOS). The large surface area of the pine biochar has the potential to sorb nutrients and other organic molecules. To test if sorption caused decreased enzyme activity, we used a laboratory assay to quantify the activity of two sorbed enzymes: BG and acid PHOS, involved in the cycling of carbon and phosphorous. The enzymes were incubated with three solid phases: (1) the high surface area pine biochar, (2) the agricultural soil, and (3) a low surface area grass biochar, for an additional comparison. We quantified the sorbed enzymes at pH 6, 7, and 8, using a Bradford protein assay, and measured the immobilized enzyme activities via high-throughput fluorometric analysis. After sorption onto pine biochar, detectable BG and PHOS activity levels dropped by over 95% relative to the soil, supporting direct sorption as one mechanism that reduces enzyme activity in biochar amended soil. This laboratory assay demonstrated that sorption could account for the lack of priming of native soil organic matter and changes in soil phosphorous cycling after pine biochar addition.

Observation of the ambient aerosol surface area concentrations is important to understand the aerosol toxicity because an increased surface area may be able to act as an enhanced reaction interface for certain reactions between aerosol particles and biological cells, as well as an augmented carrier surface for co-pollutants. In this study, the concentration of aerosol surface area was measured from April 2015 to March 2016 in Fukuoka, Japan. We investigated the monthly and diurnal variations in the correlations between the aerosol surface area and black carbon (BC) and sulfate concentrations. Throughout the year, aerosol surface area concentration was strongly correlated with the concentrations of BC, which has relatively large surface area since BC particles are usually submicron agglomerates consisting of much smaller (tens of nanometers) sized primary soot particles. The slopes of the regression between the aerosol surface area and BC concentrations was highest in August and September 2015. This appears to have been the results of an increase in the proportion of the airmass that originated on the main islands of Japan. This may enhance the introduction of the BC from the main islands of Japan that is relatively fresh (or “uncoated”), thereby maintaining its larger surface area.

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Forests are critical in regulating the world’s climate and they maintain overall Earth’s energy balance. The variability in forest canopy structure, topography and underneath vegetation background condition creates uncertainty in the estimation and modelling of Earth’s surface radiation particularly for boreal regions in high latitude. We studied seasonal variation in surface reflectance with respect to land cover classes, canopy structures, and topography in a boreal region of Alaska by fusing together Landsat 8 surface reflectance and LiDAR-derived canopy matrices. Our study shows that canopy structure and topography interplay and influence surface reflectance in a complex way particularly during the snow season. Topographic aspect and elevation control vegetation growth, type and structure. The southern slope is featured with more deciduous and taller trees having greater rugosity than the northern slope. Higher elevation is associated with taller trees for both vegetation types, particularly in the southern slope. In general, surface reflectance shows similar relationships with canopy cover, height and rugosity, mainly due to close relationships between these parameters. Surface reflectance decreases with canopy cover, tree height, and rugosity especially for evergreen forest. Deciduous forest shows larger variability of surface reflectance, particularly in March, mainly due to the mixing effect of snow and vegetation. The relationship between vegetation structure and surface reflectance is greatly impacted by topography. The negative relationship between elevation and surface reflectance may be due to taller and denser vegetation distribution in higher elevation. Surface reflectance in the southern slope is slightly larger than the northern slope for both deciduous and evergreen forest. The shadow effect from topography and tree crowns on surface reflectance play a different role for deciduous and evergreen forests. For deciduous forest, topographic shadow effect on surface reflectance is stronger than from tree shadowing in all seasons. For evergreen forest, shadow effects from topography and tree crowns on surface reflectance are both equally dominant, however tree shadow effect is more significant in March than in May and August. The generalized additive models (GAM) based on non-linear relationships between response (surface reflectance) and predictor (canopy structures and topography) variables confirms such observations. Our study not only provides accurate quantification of surface radiation budget but also helps in parametrization of climate change models.

Carbon-based nanomaterials, such as carbon nanomaterials, play an important role in many promising nanomaterials in the field of biomedicine. Among them, carbon nanomaterials are a new kind of porous carbon nanomaterials with great application potential. Therefore, based on carbon nanomaterials, the interaction between biomaterials and cells and surface modification were analyzed. Studies have shown that the interaction between the surface of biological materials and cells is mainly the mutual molecular recognition between the surface receptors of cell membranes and the ligands on the surface of biomaterials. Therefore, biomimetic modification of the surface of biomaterials is used to enhance cell affinity and specific recognition. The carbon nanomaterial has a large specific surface area and pore volume, can provide high drug-loading capacity, has an adjustable pore structure and pores, can control the release of the drug molecules, and has a good application prospect in the field of drug delivery systems.

Analysis of water resources of this area was carried out in order to assessing the water quality by determining the concentrations of Cations, Anions, Heavy metals, Trace elements, PH, Alkalinity, Total Dissolved Solids and microbial loads in water samples. Ten (10) water samples were collected from the study area - samples each of rain water, two pond waters - 1 and 2, stream water, four (4) hand-dug wells, hand pump water and a motorized borehole. The results obtained were compared with WHO standards and it showed that all the cations in water samples are within the limits. The water samples at locations B, E, F, G, H, I, and J have high alkalinity and HC0^-₃ content. The heavy metals (Pb, Ni and Cd) and trace elements (Fe and Cu) are dominantly high in the surface waters. Microbiological substances in the water samples from the study area revealed indicator organisms higher than the WHO standard for drinking water. Samples obtained from location G, I and J recorded an absence of E. coli and are fit for human consumptions but needed to be treated due to high MPN (Most Probable Number) index of viable microorganisms as against WHO standard. This research showed that the water resources of the study area are gradually polluted and in the near future may not be good for drinking.

This study evaluates the historical mean surface temperature (hereafter T2m) and examines how T2m changes over East Africa (EA) in the 21^st century using CMIP6 models. An evaluation was conducted based on mean state, trends, and statistical metrics (Bias, Correlation Coefficient, Root Mean Square Difference, and Taylor skill score). For future projections over EA, five best performing CMIP6 models (based on their performance ranking in historical mean temperature simulations) under the shared socioeconomic pathways SSP2-4.5 and SSP5-8.5 scenarios were employed. The historical simulations reveal an overestimation of the mean annual T2m cycle over the study region with fewer models depicting underestimations. Further, CMIP6 models reproduce the spatial and temporal trends within the observed range proximity. Overall, the best performing models are as follows: FGOALS-g3, HadGEM-GC31-LL, MPI-ESM2-LR, CNRM-CM6-1, and IPSL-CM6A-LR. During the three-time slice under consideration, the Multi Model Ensemble (MME) project many changes during the late period (2080 – 2100) with expected mean changes at 2.4 °C for SSP2-4.5 and 4.4 °C for the SSP5-8.5 scenario. The magnitude of change based on Sen’s slope estimator and Mann-Kendall test reveal significant increasing tendencies with projections of 0.24°C decade-1 (0.65°C decade-1) under SSP2-4.5 (SSP5-8.5) scenarios. The findings from this study illustrate higher warming in the latest model outputs of CMIP6 relative to its predecessor, despite identical instantaneous radiative forcing.

While texturing of workpiece surfaces to promote lubrication in metal forming has been applied for several decades tool surface texturing is rather new. In the present paper tool texturing is studied as a method to prevent galling. Adopting a strip reduction test longitudinal pocket geometries oriented perpendicular to the sliding direction, with shallow pocket depth, small pocket angle to the workpiece surface and varying distance between pockets are investigated. The experiments reveal that the distance between pockets should be larger than the pocket width thereby creating a topography similar to flat table mountains to avoid mechanical interlocking in the valleys; otherwise an increase in drawing load and pick-up on the tools is observed. The textured tool surface lowers friction and improves lubrication performance provided that the distance between pockets is 2-4 times larger than the pocket width. Larger drawing speed facilitates escape of the entrapped lubricant in the pockets. Testing with low to medium viscosity oils leads to a low sheet roughness on the plateaus but also local workpiece material pick-up on the tool plateaus. Large lubricant viscosity results in higher sheet plateau roughness but also prevents pick-up and galling.

This is an exercise to explore the concentration of Lithium, Lithium-7 isotope and the possible presence of black dirty ice in the lunar surface using spectral data obtained from the Clementine mission. The main interest in tracing the lithium and presence of dark ice in the lunar surface are closely related to future human settlement missions in the Moon. We investigate the distribution of Lithium and 7 Li isotope on the Lunar surface, employing spectral data from the Clementine images. We utilized Visible (VIS-NIR) imagery at wavelengths of 450, 750, 900, 950, and 1000 nm, along with Near-Infrared (NIR-SWIR) at 1100, 1250, 1500, 2000, 2600, and 2780 nm, encompassing 11 bands in total. This dataset offers a comprehensive coverage of about 80% of the lunar surface, with resolutions ranging from 100 to 500 meters, spanning latitudes from 80°S to 80°N. In order to extract quantitative abundance of Lithium, ground truth sites were used to calibrate the Clementine images. Samples (12045, 15058, 15475, 15555, 62255, 70035, 74220 and 75075) returned from Apollo missions 12, 15, 16 and 17 have been correlated to the Clementine VIS-NIR bands and five spectral ratios. The 5 spectral ratios calculated synthesize the main spectral features of sample spectra that were grouped by their Lithium and 7 Li content using Principal Component Analysis. The ratios spectrally characterize substrates of anorthosite, silica-rich basalts, olivine-rich basalts and High-T mare basalts and Orange soils. Our findings reveal a strong linear correlation between the spectral parameters and the lithium content in the 8 Apollo samples. With the values of the 11 Clementine bands and the 5 spectral ratios for each of the 8 lunar soils we performed linear regression models to estimate the concentration of Lithium and 7 Li. Also, we calculated Digital Terrain Models (DTMs; Altitude, Slope, Aspect, DirectInsolation and WindExposition) from LOLA-DTM to discover relations between relief and spatial distribution of the extended models of lithium and 7 Li. The analysis was conducted in a mask polygon extracted from Lunar Orbiter Laser Altimeter (LOLA) and located around the Apollo 15 landing site. This analysis seeks to uncover potential 7 Li enrichment through spallation processes, influenced by varying exposure to solar wind. To explore the possibility of find ice mixed with regolithe (black ice) we used a spectral library (350-2500nm) form ices dirty with different concentration of volcanic particles.

Mixed cadmium tellurides – cadmium sulfides thin layers were formed on the polyamide PA 6. Monotelluropentathionic acid (H2TeS4O6) was used as precursor of tellurium and sulfur. We applied a low-temperature, nontoxic and cost-effective SILAR method. Cadmium telluride (CdTe) and sulfide (CdS) layers were formed through consecutive reactions of sorbed/diffused chalcogens species from telluropentathionate anion (TeS4O62–) with functional groups of polyamide and alkaline cadmium sulfate. The pseudo-second-order rate and Elovich kinetic models best fitted to quantify an uptake of chalcogens and cadmium on PA6. The effects of chalcogens and Cd on the structure and optical properties of PA6 were characterized using UV/Vis and IR spectra. The clear changes of these properties found in dependence on the concentration and exposure time in precursor's solutions. Fourier transform infrared spectroscopy and an ultraviolet-visible spectroscopy were applied in order to evaluate the effect of the chalcogens having particles on the changes in structure of polyamide 6 films depending on the exposure time in the solution of the chalcogens precursor and its concentration. The optical band gap energy of formed layers was found to be in the order of 1.52–2.36 eV. Studies of scanning electron microscopy and atomic force microscopy reveal that the diameter of the average grain is about 30 nm. The grains are conical in shape and unevenly distributed all over the surface of the substrate.

The study of the distribution and health risk assessment is meaningful to provide basic data for environmental management．To investigate the pollution of potential toxic organics and their health risk to human beings, water samples were collected at 7 sites of main surface water of Beijing during wet and dry seasons respectively. The targeted 92 organics were detected, including phthalates (PAEs), volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) and phenols. The results showed that: there were 56 organics detected out, and the number ratios of detected compounds to the total compounds of the same kind increased as the following: VOCs, phthalates, phenols, PAHs. 8 VOCs were detected in wet season, and 3 in dry season. The concentration of 2,2-Dichloropropane was highest as 10.62ug/L, while the concentrations of other VOCs were below 5ug/L; There were 11 phthalates detected during dry season. The content of Bis(2-methoxyethyl) phthalate was highest as 188.47ng/L; 17 phenols were found in samples during wet season, and the highest concentration was 1244.73ng/L for 4-nitrophenol; PAHs could be detected in all samples, and the detected compounds and the corresponding average concentrations were higher in wet seasons than those in dry seasons, which indicated that non-point pollution was possibly the main pollution source. The health risk assessment of the detected 56 pollutants by using a model from US EPA showed that, the risk caused by the four kinds of toxic organics in this study was in the acceptable ranges.

1) Background: The objective was to evaluate the corrosion resistance of different commercially pure ultrafine-grained (UFG) titanium and its alloys with acid etched surface processed by equal-channel angular pressing (ECAP); 2) Methods: Coarse-grained and UFG titanium samples were investigated using polarization resistance technique. Surface characteristics of the native oxidized layer were evaluated by TEM and XRD. Electrochemical tests were under physiological electrolyte at a rate of 1 and 10 mV/s. Weight loss tests were performed after immersion into HCl solution for up to 3 years; 3) Results: UFG titanium was less susceptible to corrosion which was identified under lower rates and at higher polarization resistance than its coarse grain counterparts. Titanium Grade 2 and Grade 4 demonstrated similar corrosion susceptibility. Titanium Grade 5 revealed a thin and tightly adhered native oxide layer with adequate corrosion resistance; 4) Conclusions: ECAP process imposed a more compact and adhered oxidized layer. Surface etching techniques delivered a thicker native TiO₂ layer, being both grain refinement and surface etching techniques responsible for the improved corrosion resistance of Titanium samples under physiological environment after 3 years of observation.

In this study we present gas-phase fluorination as a method to create a thin LiF layer on Li6.5La3Zr1.5Ta0.5O12 (LLZTO). We compare these fluorinated films with LiF films produced by RF-magnetron sputtering, where we investigated the interface between the LLZTO and the deposited LiF showing no formation of a reaction layer. Furthermore, we investigate the ability of this LiF layer as a protection layer against Li2CO3 formation in ambient air. By this we show that Li2CO3 formation is absent at the LLZTO surface after 24 h in ambient air supporting the protective character of the formed LiF films and hence could enhance the handling of LLZTO in air for battery production. With respect to the use within hybrid electrolytes consisting of LLZTO and a mixture of polyethylene oxide (PEO) and Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) we also investigated the interface between the formed LiF films and a mixture of PEO LiTFSI by X-ray photoelectron spectroscopy (XPS) showing decomposition of the LiTFSI at the interface.

The athletic performance and safety of racehorses is influenced by hoof-surface interactions. This intervention study assessed the effect of eight horseshoe-surface combinations on hoof acceleration patterns at impact and foot-off in 14 galloping Thoroughbred racehorses retired from racing. Aluminium, barefoot, GluShu (aluminium-rubber composite) and steel shoeing conditions were trialled on turf and artificial (Martin Collins Activ-Track) surfaces. Shod conditions were applied across all four hooves. Tri-axial accelerometers (SlamStickX, range ±500 g, sampling rate 5000 Hz) were attached to the dorsal hoof wall (x: medio-lateral, medial=positive; y: along dorsal hoof wall, proximal=positive; z: perpendicular to hoof wall, dorsal=positive). Linear mixed models assessed whether surface, shoeing condition or stride time influenced maximum (most positive) or minimum (most negative) accelerations in x, y and z directions, using ≥40,691 strides (significance at p&lt;0.05). Day and horse-rider pair were included as random factors and stride time as a covariate. Collective mean accelerations across x, y and z axes were 22–98 g at impact and 17–89 g at foot-off. Mean stride time was 0.48 ± 0.07 s (mean ± 2 s.d.). Impact accelerations were larger on turf in all directions for forelimbs and hindlimbs (p≤0.015), with the exception of forelimb z-minimum, and in absolute terms maximum values were typically double minimum values. Surface-type affected all foot-off accelerations (p≤0.022), with the exception of hindlimb x-maximum; for example, there was an average increase of 17% in z-maximum across limbs on the artificial track. Shoe-type influenced all impact and foot-off accelerations in forelimb and hindlimb datasets (p≤0.024), with the exception of hindlimb impact y-maximum. Barefoot hooves generally experienced the lowest accelerations. Stride time affected all impact and foot-off accelerations (p<0.001). Identifying factors influencing hoof vibrations on landing and hoof motion during propulsion bears implication for injury risk and racing outcomes.

The constant increase in current density in electrical wires leads to increasingly significant heat losses due to Joule effect. Therefore, reducing the electrical resistivity of copper wires becomes necessary. To achieve this goal, the development of a composite material incorporating a more conductive reinforcement, the graphene, is a promising way. The design of a copper/graphene composite using a powder metallurgy-based method is presented. This synthesis method allows for interface control through the growth of CuO(Cu) nanoparticles tightly bonded to the reinforcement. It also involves the dispersion of graphene through ultrasonic treatment and its alignment within the matrix using a uniaxial pressing densification method. The increase in the hardness (+12 HV) demonstrates the effective dispersion and separation of graphene layers. The impact on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, with a decrease in electrical resistance of approximately 1.4%. However, for copper with higher electrical resistivity, flake copper (at 2.71 µΩ.cm) and brass at (7.66 µΩ.cm), reductions of 2.7% and 10% have been achieved, respectively. With the improvement of graphene quality, there is more room to improve the electrical properties. This work paves the way for the development of composites with improved electrical resistivity.

A Invasive emerging pollutants from wastewater effluent discharge, such as dyes, pesticides, etc., pose a serious threat to the ecosystem. Advanced oxidation processes (AOPs) under visible light irradiation have emerged as a promising technology to overcome toxic and recalcitrant organic compounds. In this work, the impact of operational factors, including the concentration of Fe3+ or Fe2+, [H2O2], the molar ratio (Oxalate/ Fe3+ or Fe2+), and the initial pH, was studied to obtain high efficiency in the degradation and mineralization of such a food dye to reduce their pollution. The study deals with the comparison of the efficiency of UV, LED, and sunlight irradiation on the photocatalytic degradation of the dye using Fe3+/Lig and Fe2+/Lig complexes. The results showed that sunlight irradiation gave a very rapid kinetic and higher degradation efficiency of over 70%. The optimized conditions for the maximum elimination of the dye with a photocatalytic degradation efficiency (98%) and a mineralization rate of 96% were obtained with the Fe3+/Lig complex, based on the Box Benhken surface design analysis. In the presence of H2O2, the degradation reached an equilibrium stage after 15 min (97.57%) for the Fe(III)/Lig system. Moreover, the inhibition effect of inorganic ions on the photo-Fenton performance of Fe3+/Lig and Fe2+/Lig was studied. The study suggests that the use of nanocrystals of hematite as a Fenton reagent for treating textile effluents needs further investigation. The results showed that the proposed models were well-suited to batch treatment under sunlight. This study not only proposes a Fe3+/Lig and Fe2+/Lig system for the elimination of a food dye without adjusting the pH of the medium, but it also provides insight into the best source of light irradiation for the photocatalytic degradation process.

MicroRNAs are small ribonucleotides which act as key gene regulators. Their altered expression is often associated with onset and progression of several human diseases, including cancer. Given their potential use as biomarkers, there is a need to find detection methods of microRNAs suitable for use in clinical setting. Field Effect Transistor based biosensors (bioFETs) appear to be valid tools to detect microRNAs, since they may reliably quantitate the specific binding between the immobilized probe and free target in solution through an easily detectable electrical signal. We have investigated the detection of human microRNA 155 (miR-155) using an innovative cap-turing probe constituted by a synthetic peptide nucleic acid (PNA), which has the advantage to form a duplex even at ionic strengths approaching the physiological conditions. With the aim to develop an optimized BioFET setup, the interaction kinetics between miR-155 and the chosen PNA was preliminary investigated by Surface Plasmon Resonance (SPR). By exploiting both these results and our custom-made bioFET system, we were able to attain a low-cost, real-time, label-free, highly specific detection of miR-155 in the nano-molar range.

Understanding the effect of horseshoe-surface combinations on hoof kinematics at gallop is relevant for optimising performance and minimising injury in racehorse-jockey dyads. This intervention study assessed hoof breakover duration in Thoroughbred ex-racehorses from the British Racing School galloping on turf and artificial tracks in four shoeing conditions: barefoot, aluminium-rubber composite (GluShu), aluminium and steel. Shoe-surface combinations were tested in a randomized order and horse-rider pairings (n=14) remained constant. High-speed video cameras (Sony DSC-RX100M5) filmed the hoof-ground interactions at 1000 frames per second. The time taken for a hoof marker wand fixed to the lateral hoof wall to rotate through an angle of 90 degrees during 384 breakover events was quantified using Tracker software. Data were collected for leading and non-leading front and hind limbs, at gallop speeds ranging from 23–56 km h-1. Linear mixed-models assessed whether speed, surface, shoeing condition or any interaction between these parameters (fixed factors) significantly affected breakover duration. Day and horse-rider pair were included as random factors and speed was included as a covariate. The significance threshold was set at p&lt;0.05. For all limbs, breakover times decreased as gallop speed increased (p&lt;0.0005), although a greater relative reduction in breakover duration for hindlimbs was apparent beyond approximately 45 km h-1. Breakover duration was longer on turf compared to the artificial surface (p≤0.04). In the non-leading hindlimb only, breakover duration was affected by shoeing condition (p=0.025) and an interaction between shoeing condition and speed (p=0.023). Future work seeks to relate these results to hoof accelerometer data.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

Substantial reductions of the human and economic activities like road traffic for several months in 2020 were one of the consequences of the Coronavirus disease. This unprecedented change in urban metabolism also affected temperature and air pollutants. This study investigates the effects of the first COVID-19 lockdown over 43 cities in Europe. It determines the influence of anthropogenic activities on nitrogen dioxide (NO2), ozone (O3), and particulate matter (PM2.5) as well as on land surface temperature (LST), and the surface urban heat island intensity (SUHII), using satellite, modelled, and mobility data. Our findings show that there are great temporal and spatial differences and distinct patterns between the cities regarding the magnitude of change of the variables under study. In general, the results indicate a significant decrease in NO2 concentrations in most of the studied cities compared to the reference period 2015-2019. However, reductions could not be attributed to mobility changes like less traffic at transit stations, contrary to the results of previous studies. O3 levels increased during the first lockdown mainly influenced by the decreasing NO2 concentrations. The PM pattern was inconsistent over time and space. Similar as the NO2 results, no relation to the altered mobility behavior was found. No clear signal could be detected for LST and the SUHII, likely due to dominating meteorological influences. Therefore, single city case studies may be misleading.

Shaped surfaces are increasingly used in the field of mould making for casting or injection moulding, where future products include shapes with different curvatures. These are surfaces that form convex curves, concave curves, or a combination thereof. Given these machined surfaces, it is important to know the impact of the finishing strategies on these surfaces. This paper deals with the comparison of finishing milling strategies in the production of shaped surfaces and the analysis of different methods for the evaluation of surface topography, surface roughness and the evaluation of deviations. The material used for the experiments was AlCu4Mg aluminium alloy, and Constant Z, Spiral and Spiral circle strategies were chosen for the finishing strategies. The evaluation of surface topography and surface roughness was carried out at three different sample heights with respect to the tool contact with the machined surface. The results showed changes in the toolpaths due to the variation of the effective diameter of the tool cutter to the machined surface as well as the choice of strategy. To produce specimens with corresponding shapes in terms of topography, the Constant Z strategy was the most suitable, in which uniform toolpaths were obtained over the whole height of the sample.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Three-dimensional flexible piezoresistive porous sensors have been used in health diagnosis and wearable devices. By utilizing 3D printed sacrificial mold casting with highly conductive polymer composites, porous sensors with high conductivity and complex structures were achieved. Traditional conductive polymer composites are usually heated using external heat sources, which are time and energy consuming. However, in this study, conductive porous sensors with triply periodic minimal surface (TPMS) structures were manufactured using self-resistance electric heating by utilizing the conductive nature of the polymers. The porous structures were designed based on Diamond (D), Gyroid (G), and I-WP (I) unit cells of the TPMS. The use of self-resistance electric heating has improved the compression performance and piezoresistive response of the structures. Among these structures, the D-based structure exhibited the maximum response strain (61 %), with a corresponding resistance response value of 0.97, which increased by 10.26 % compared to that of the structures heated by using the external heat sources. This study offers a new perspective on designing and optimizing porous materials with specific functionalities, particularly in the realm of flexible and portable piezoresistive sensors.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

Nobel metal nanohole arrays have been used extensively in chemical and biological systems due to their fascinating optical properties. Gold nanohole arrays (Au NHAs) were prepared as surface plasmon polaritons (SPP) generators for the surface-enhanced sum-frequency generation (SFG) detection of 4-Mercaptobenzonitrile (4-MBN). The angle-resolved reflectance spectra revealed that the Au NHAs have three angle-dependent SPP modes and two non-dispersive localized surface plasmon resonance (LSPR) modes under different structural orientation angles (sample surface orientation). An enhancement factor of ~30 was achieved when the SPP and LSPR modes of the Au NHAs were tuned to match the incident visible (VIS) and output SFG, respectively. This multi-mode matching strategy provided flexible controls and selective spectral windows for surface-enhanced measurements, and was especially useful in nonlinear spectroscopy where more than one light beam involved. The structural orientation- and power-dependent performance demonstrated the potential of plasmonic NHAs in SFG and other nonlinear sensing applications, and provided a promising surface molecular analysis development platform.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

Statement of problem: Henna has been added to polymethylmethacrylate (PMMA) as a new type of antifungal agent; however, its effect on the latter’s physical properties has not been investigated. Purpose: This study aimed to evaluate the effect of the addition of various henna concentrations on the surface roughness and hardness of PMMA denture base material. Materials and Methods: A total of 99 specimens of rectangular-shaped (10×20×3 mm3) acrylic specimens were prepared from heat-cured acrylic resin. Specimens were divided into one control group without the addition of henna and five test groups, which were prepared by adding Yamani henna powder to acrylic powder at concentrations of 1wt%, 2.5wt%, 5wt%, 7.5wt%, and 10wt%. The polymer was added to the monomer before being mixed, packed, and processed using the conventional water bath method. After processing, specimens were finished and polished, then kept in distilled water for 48+2 h. A profilometer and Vickers hardness tester were used to measure surface roughness and hardness respectively. Statistical data analysis was conducted via SPSS version 20.0 (IBM, USA). Results: The addition of henna at varying concentrations significantly increased surface roughness values (P ≤ 0.01) while decreasing hardness (P ≤ 0.0001). The most favorable addition value was 1% henna between all henna groups. Conclusion: The addition of henna to the acrylic resin may negatively affect the surface properties of PMMA acrylic denture base.

Recently a new class of experiments in the field of surface gravity waves has emerged. These experiments serve as demonstration of an analogy to a broad variety of phenomena in optics and quantum mechanics. In particular, experiments involving Airy water-wave packets were carried out. The Airy wave packets have attracted tremendous attention in optics and quantum mechanics owing to their unique properties, spanning from an ability to propagate along parabolic trajectories without spreading, and to accumulating a phase that scales with the cubic power of time. Non-dispersive Cosine-Gauss wave packets and self-similar Hermite-Gauss wave packets, also well known in the field of optics and quantum mechanics, were recently studied using surface gravity waves as well. These wave packets demonstrated self-healing properties in water wave pulses as well, preserving their width despite being dispersive. Finally, this new approach also allows to observe diffractive focusing from a temporal slit with finite width.

Earth’s land surface area is raised from conventionally flat 15 to 64 Gha to account for hilly undulation and soil relief detail. Three main aspects are: topography, rugosity/tortuosity and micro-relief/porosity of vegetation-free ground. Recalibration is arrived at from four approaches: first, direct empirical estimates from the few compiled satellite or LiDAR data with means of +2.5–26% progressively overlain by +94% at cm² scale for soil ruggedness then +108% for mm² micro-relief; second, from digital elevation models with 1.6–2.0 times flat areas; third, by ‘reverse engineering’ global soil bulk densities and carbon reserves requiring x 2–6 land. Finally, a Fermi estimation conveniently sets the World’s new surface area – that exposed to Sun, air and rain – at 100 Gha (with 36 Gha flat ocean). Soil organic carbon (SOC) is thence raised to 8,580 Gt mainly in SOM/humus with its biotic complexity plus roots, VAM-fungi and leaf-litter, that itself = 17,800 Gt. Although four to six times IPCC’s or NASA/NOAA’s calculations of just 1,500–2,300 Gt SOC, this is likely an underestimation. Global biomass and biodiversity are at least doubled (x 2–3.5) and net primary productivity (NPP) similarly increased on land to >270 Gt C yr^-1 due to terrain.

Analysis of the correlation between indices (Normalized Difference Vegetation Index, Normalized Difference Barren Index and Modified Normalized Difference Water Index) and land surface temperature is used to natural resources and environmental studies. This research aimed to analysis of Land Surface Temperature due to dynamics of Different Indices (NDVI, NDBaI and MNDWI) Using Remote Sensing Data in three selected districts (Gida Kiremu, Limu and Amuru), western Ethiopia. From thermal and multispectral bands of landsat imageries (Landsat TM of 1990, landsat ETM+ of 2003 and landsat OLI/TIRS of 2020) Land surface temperature and NDVI, NDBaI and MNDWI were calculated. Correlation analysis was used to indicate relationships between LST with NDVI, NDBaI and MNDWI. The study found that Land Surface Temperature was increased by 5⁰C from 1990 to 2020. Vegetation areas (NDVI) and Water bodies (MNDWI) have strong negative relationship with Land Surface Temperature (R²= 0.99, 0.95) whereas Barren land (NDBaI) has positive relationship with Land Surface Temperature (R²= 0.96). Finally, we recommend the decision makers and environmental analyst to emphasis the importance of vegetation cover and water body to minimize the potential impacts of land surface temperature.

African trypanosomes are an early branch in eukaryotic evolution and developed a unique endomembrane system as an adaptation to their parasitic life style. The key virulence mechanism of many pathogens is successful immune evasion to enable survival within the host, which is a feature requiring both genetic events and membrane transport in African trypanosomes. Intracellular trafficking not only plays a role in immune evasion, but also in homeostasis of intracellular and extracellular compartments and interactions with the environment. Significantly, historical and recent work has unravelled some of the connections between these processes and highlighted how immune evasion mechanisms associated with adaptations in membrane trafficking may have, paradoxically, provided specific sensitivity to drugs. Here we explore these advances in understanding the membrane composition of the trypanosome plasma membrane and organelles and provide a perspective for how transport could be exploited for therapeutic purpose.

Bio-surfactants are surface-active molecules which are produced by the wide range of microbes including bacteria, fungi, and yeast. This study was conducted to identify bio-surfactants by Bacillus subtilis combined with use of cheap substrates and industrial wastes (Mustard cake, Whey and Soya cake) which are found locally in Nepal. Bacillus subtilis, one of the most potential bio-surfactants producer; was isolated from soil sample of hydrocarbon contaminated site. Isolates were grown in a Minimal Salt Media (MSM) with 10% (v/v) mustard oil cake, whey and soya cake separately. The presence and potential of surfactant was determined by the oil spreading technique, emulsification index (%E24) and surface tension measurement. It was revealed that the surface tensions of cell free extract were 54.41, 60.02 and 56.64 mN/m for from mustard cake, whey and soya cake respectively as compared to distilled water (72.09) at 25oC. The emulsification index values are was found to be highest in engine oil from the bio-surfactant extracted from mustard cake, soya cake and whey respectively. Similarly, mustard oil showed the lowest value of emulsification index. The highest emulsification activity was shown in mustard oil i.e. 1.13 from the cell free extract from mustard oil and lowest in engine oil i.e., 0.07, by the extract from soya cake medium, when measured in spectrophotometer at 540 nm. In conclusion, strain of Bacillus subtilis was found to be the potential surface active agent producers on the mustard oil cake, which can be useful medium for various environmental, food and industrial processes.

Unmanned aerial vehicle (UAV) photogrammetry allows the generation of orthophoto and digital surface model (DSM) rasters of a terrain. However, DSMs of water bodies mapped using this technique often reveal distortions in the water surface, thereby impeding the accurate sampling of water surface elevation (WSE) from DSMs. This study investigates the capability of deep neural networks to accommodate the aforementioned perturbations and effectively estimate WSE from photogrammetric rasters. Convolutional neural networks (CNNs) were employed for this purpose. Two regression approaches utilizing CNNs were explored: direct regression employing an encoder and solution based on prediction of the weight mask by an encoder-decoder architecture, subse-quently used to sample values from the photogrammetric DSM. The dataset employed in this study comprises data collected from five case studies of small lowland streams in Poland and Denmark, consisting of 322 DSM and orthophoto raster samples. Each sample corresponds to a 10 by 10 meter area of the stream channel and adjacent land. A grid search was employed to identify the optimal combination of encoder, mask generation architecture, and batch size among multiple candidates. Solutions were evaluated using two cross-validation methods: stratified k-fold cross-validation, where validation subsets maintained the same proportion of samples from all case studies, and leave-one-case-out cross-validation, where the validation dataset originates entirely from a single case study, and the training set consists of samples from other case studies. The proposed solution was compared with existing methods for measuring WSE in small streams using a drone. The results indicate that the solution outperforms previous photogrammetry-based methods and is second only to the radar-based method, which is considered the most accurate method available. The solution is characterized by a high degree of explainability and generalization.

The aim of this study was to evaluate the emulsification properties of garlic water-soluble compounds (GWSC) after heat treatment (10 min at 95 °C) or pH adjustments (2.5, 3.5 and 7.8). After the various treatments, the extracts were used as such or filtrated (0.45 µm) and 10% soybean oil-in-water emulsions were prepared using low (0.48%) or high (6.55% wt/wt) extract concentrations. Whereas at low GWSC concentration, both heating or acidifying resulted in the formation of bigger oil droplet sizes (i.e. from d32=0.36 µm using unmodified extract, to d32=7–22 µm µm at pH 2.5 with or without extract filtration), the effects were opposite at the highest GWSC concentration. In the latter, heat treatment clearly reduced the droplet size as observed from the micrographs as well as the degree of creaming, though the occurrence of depletion and/or bridging flocculation was still strong. The acidification of the extract at this high GWSC concentration, significantly reduced the droplet size as observed from the micrographs but a strong flocculation was observed. Removal of protein aggregates, and possibly also saponin micelles from the extract, resulted in an obvious increase in emulsion droplet size. This research brings valuable insights on the study and utilisation of novel natural food emulsifiers from plant sources.

Iapetus, a Saturn moon, shows the most differentiated albedo dichotomy of the Solar System. The dark leading side has a lower albedo than the bright trailing side. Spectral data on the visible light reveal the existence of two types of materials on the surface. The darkening in the leading side is thought to be originated by the presence of organic material and carbonaceous compounds on surface, while the trailing side is covered by water ice due to migration processes from the dark side. On airless bodies like Iapetus, the surface escape speed is greater than the speed of water molecules, resulting in the retention of a H2O atmosphere that allows some species to get diffused through it. Here, there were performed simulations of the evolution of the surface temperature for each of the two hemispheres of Iapetus. The results showed a slow yet steady increment of temperatures for both sides, with a steeper slope for the dark hemisphere. It was also simulated how much energy budget can be accumulated in both sides and its consequences. Finally, we calculated the diffusion coefficients for ammonia, methane, and water ice. The results let us infer how these compounds could evolve over time.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

Remote sensing technologies are critical for analyzing the escalating impacts of global climate change and increasing urbanization, providing vital insights into land surface temperature (LST), land use and cover (LULC) changes, and the identification of urban heat island (UHI) and surface urban heat island (SUHI) phenomena. This research focuses on the nexus between LULC alterations and variations in LST and air temperature (Tair), with a specific emphasis on the intensified SUHI effect in Kharkiv, Ukraine. Employing an integrated approach, the study analyzes time-series data from Landsat and MODIS satellites, alongside Tair climate records, utilizing machine learning techniques and linear regression analysis. Key findings indicate a statistically significant upward trend in Tair and LST during summer months from 1984 to 2023, with a notable positive correlation between Tair and LST across both datasets. MODIS data exhibit a stronger correlation R² = 0.879, compared to Landsat R² = 0.663. The application of supervised classification through Random Forest algorithms and vegetation indices on LULC data reveals significant alterations, manifested as a 70.3% increase in urban land, concurrently with a decrement in vegetative cover, especially 15.5% reduction in dense vegetation and a 62.9% decrease in sparse vegetation. Change detection analysis elucidates a 24.6% conversion of sparse vegetation into urban land, underscoring a pronounced trajectory towards urbanization. Temporal and seasonal LST variations across different LULC classes were analyzed using kernel density estimation (KDE) and boxplot analysis. Urban areas and sparse vegetation had the smallest average LST fluctuations, at 2.09°C and 2.16°C, respectively, but recorded the most extreme LST values. Water and dense vegetation classes exhibited slightly larger fluctuations of 2.30°C and 2.24°C, with the bare land class showing the highest fluctuation 2.46°C, but fewer extremes. Quantitative analysis with the application of Kolmogorov-Smirnov tests across various LULC classes substantiated the normality of LST distributions p &gt; 0.05 for both monthly and annual data sets. Conversely, the Shapiro-Wilk test validated the normal distribution hypothesis exclusively for monthly data, indicating deviations from normality in the annual data. Thresholded LST classifies urban and bare lands as warmest classes with 39.51°C, 38.20°C and water by 35.96°C and dense vegetation 35.52°C, sparse vegetation 37.71°C as coldest, a trend consistent annually and monthly. The analysis of SUHI effects demonstrates an increasing trend in UHI intensity, with statistical trends indicating a growth in average SUHI values over time. This comprehensive study underscores the critical role of remote sensing in understanding and addressing the impacts of climate change and urbanization on local and global climates, emphasizing the need for sustainable urban planning and green infrastructure to mitigate UHI effects.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

We investigated the structural evolution of the two-phase blends of polycarbonate (PC) and poly(methyl methacrylate) (PMMA) at various blend compositions by simultaneous biaxial stretching using optical microscopy and SEM observation. The spherical PMMA domains and PC matrix in 30/70 PC/PMMA were enlarged uniformly at all in-plane direction, while the anisotropic-shaped co-continuous structure in 50/50 PC/PMMA was deformed to crosshatched one by in-plane bimodal orientation. In 70/30 PC/PMMA, the phase inversion was found to occur by simultaneous biaxial stretching; i.e., the spherical PMMA domains were changed to crosshatched matrix by in-plane bimodal orientation due to coalescence of the PMMA domains during the stretching. Owing to the phase inversion, the surface hardness estimated by pencil hardness test became harder from 2B to 2H with increasing the strain from 1.0 to 2.0.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

The article presents a new method called slide roller burnishing (SRB) for cold working of cylindrical surfaces on machine tools, implemented with a novel multi-functional device. The machined material was chromium–nickel austenitic stainless steel. The deforming element is a toroidal roller whose axis crosses that of the workpiece. As a result, a relative sliding velocity occurs in the contact zone between the roller and the machined surface. The sliding velocity vector is set using the burnishing device. The theoretical background of SRB is presented. When the two axes are parallel, the well-known roller burnishing (RB) method is implemented. Thus, RB is a special case of SRB. Both processes are realized using the multi-functional burnishing device. The RB process was studied experimentally and optimized according to three criteria, based on the relationship between the surface integrity and operating behavio of the respective component, to achieve three processes: smoothing, hardening and mixed burnishing. Using the optimal RB parameters obtained, the dependence of the results of SRB on the crossing angle was investigated and optimized. A comparative analysis was performed between the optimized RB and SRB processes (respectively for their three variants: smoothing, hardening and mixed) based on geometrical and physical–mechanical characteristics of the surface integrity. The main advantage of the SRB is that it provides smaller height roughness parameters and a higher surface microhardness than RB.

Many studies have focused on the impacts of rainfall duration and intensity while overlooking the role of rainfall patterns on intensive tillage erosion in hilly agricultural landscapes. The objective of this study was to determine the combined effects of rainfall patterns and intensive tillage erosion on surface runoff and soil loss on sloping farmland in the purple-soil area of China. Five simulated rainfall patterns (constant, rising, falling, rising-falling, and falling-rising) with the same total precipitation were designed, and the intensive tillage erosion treatment (IT) and no-tillage treatment (NT) were subjected to simulated rainfall using rectangular steel tanks (2 m × 5 m) with a slope of 15°. To analyse the differences in the hydrodynamic characteristics induced by tillage erosion, we calculated the flow velocity (V), Reynolds number (Re), Froude number (Fr), and Darcy-Weisbach resistance coefficient (f). The results indicate that significant differences in surface runoff and soil loss were found among different rainfall patterns and stages (P < 0.05). The falling pattern and falling-rising pattern had faster runoff-initiating times and larger sediment yields than those of the other rainfall patterns. f varied from 0.30 to 9.05 for the IT and 0.48 to 11.57 for the NT and exhibited an approximately inverse trend to V and Fr over the course of the rainfall events. Compared with the NT, the mean sediment yield rates from the IT increased the dynamic range of 8.34%–16.21% among different rainfall patterns. The net contributions of the IT ranged from 2.77% to 46.39% on surface runoff and 10.14%–78.95% on soil loss on sloping farmland. Surface runoff and soil loss were positively correlated with rainfall intensity, V, and Fr but negatively correlated with f irrespective of tillage intensive (P < 0.05). For varying-intensity rainfall patterns, soil and water loss fluctuated during rainfall events, suggesting that the changes in rainfall intensity and tillage intensity would result in drastic variations in soil hydrological characteristics and sediment transport mechanisms. The time sequences of rainfall intensity in each rainfall pattern significantly affected surface runoff, soil erosion, and their contribution rates to total soil and water loss. Moreover, tillage erosion effects on soil and water loss were closely related to rainfall patterns in hilly agricultural landscapes. Our study not only sheds light on the mechanism of tillage erosion and rainfall erosion but also provides useful insights for developing tillage-water erosion prediction models to evaluate soil and water loss on cultivated hillslopes.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

Microencapsulation by atomization can be used to minimize the loss of bioactive compounds, improving the characteristics and applicability of the powdered product. This study evaluates the effect of different encapsulating agents (maltodextrin, gum arabic, and chitosan) and three spray nozzle diameters (1.0, 1.2, and 1.5 mm) on the atomization of guavira (Campomanesia adamantium) pulp with added 6% bocaiuva (Acrocomia aculeata) dehydrated pulp in the green maturation stage. The experiment followed a simplex-centroid mixed design, with carrier agent concentrations and spray nozzle diameters as independent variables and powder yield, solubility, hygroscopicity, and vitamin C content as dependent variables. The results show that gum arabica increased powder yield and vitamin C retention. The addition of maltodextrin resulted in powders with increased solubility and low hygroscopicity. Furthermore, the optimization tool indicated that the best process conditions were achieved with the addition of gum arabic (10.8%) and chitosan (7.2%), resulting in powders with 29.48% yield, 82.96% solubility, 15.90% hygroscopicity and 741.11 mg/100g vitamin C. Furthermore, the 1.0 mm diameter spray nozzle was considered the most suitable for obtaining guavira pulp microparticles with higher ascorbic acid content.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Pollution of urban surface dust with hazardous elements (HEs) is a serious environmental issue due to its toxicity and potential hazardous effects. Surface dust samples were collected from core urban, urban, and suburban gradients in the Urumqi city of the arid NW China, and the concentrations of six HEs, such as arsenic (As), cadmium (Cd), nickel (Ni), lead (Pb), mercury (Hg), and chromium (Cr), were determined. The pollution load index (PLI) and the US EPA health risk assessment model were applied to analyze and compare the pollution levels and potential health risk of HEs in surface dusts in different urbanization gradients. The obtained results indicate that the average concentrations of Hg, Cd, and Ni in surface dust decrease in the order of core urban > urban > suburban, whereas the average concentrations of As, Cr, and Pb decrease in the order of urban > core urban > suburban. The PLI of HEs in surface dust decreased in the order of core urban > urban > suburban. The concentrations of HEs in the core urban and urban gradients are relatively higher than in the suburban gradient. Furthermore, the total non-carcinogenic and carcinogenic risk index of investigated HEs in surface dust decrease in order of urban > core urban > suburban, for both adults and children. In addition, the pollution of surface dust with HEs in all urbanization gradients is more harmful to the children's health than to the adults. Overall, the potential non-carcinogenic and carcinogenic health risks of the investigated HEs, instigated primarily by oral ingestion of surface dust, are found to be within the acceptable range. However, urbanization can effects the accumulation of HEs in surface dust, and Cr is the main non-carcinogenic risk factor, whereas Cd is the main carcinogenic risk factor among the analyzed HEs in surface dust in all urbanization gradients.

The synthesis 2-tert-butyl-4-methylphenol is of great significance because of its widely application in industry, and the development of highly efficient catalyst is necessary to the alkylation of p-cresol and tert-butyl alcohol. Here, an efficient and mild method was established, caprolactam was chosen as hydrogen-bonding acceptor, p-toluenesulfonic acid was employed as hydrogen-bonding donor, and deep eutectic solvent (DES) was prepared to catalyze the alkylation reaction. The structure of the DES catalyst was characterized by 1H NMR spectra, thermogravimetric analysis and fourier transform infrared spectra (FT-IR). In addition, response surface design based on Box-Behnken method was employed to optimize the alkylation reaction process parameters, the study of reaction kinetics was also carried out subsequently. The recycle performance of the catalyst was evaluated by recovery experiments, and a good result was obtained. Comparing with the literature reported, we here provide a mild method to the synthesis of 2-tert-butyl-4-methylphenol.

Mapping and prediction of inundated areas is increasingly important for climate change adaptation and emergency preparedness. Flood forecasting tools and flood risk models have to be compared to observed flooding patterns for training, calibration, validation and benchmarking. At regional to continental scale, satellite earth observation is the established method for surface water extent (SWE) mapping and several operational global-scale data products are available. However, the spatial resolution of satellite-derived SWE maps remains a limiting factor, especially in low-lying areas with complex hydrography, such as Denmark. We collected thermal imagery using an unmanned airborne system (UAS) for three areas in Denmark shortly after major flooding events. We combined the thermal imagery with an airborne lidar-derived high-resolution digital surface model of the country to retrieve high-resolution (40 cm) SWE maps. The resulting SWE maps were compared to low-resolution SWE maps derived from satellite earth observation (EO). We conclude that UAS have significant potential for SWE mapping at intermediate scales, can bridge the scale gap between ground observations and satellite EO and can be used to benchmark and validate SWE mapping products derived from satellite EO as well as models predicting inundation.

Climate and land use changes are two factors affecting the hydrology of watersheds. The greatest effect of climate change is probably the change in the hydrological cycle, thus water availability for human consumption, industry, and power generation. While the change in land use can cause changes in the hydrological components of the basin, such as evapotranspiration, runoff, and groundwater recharge. From these projections, it is necessary to understand the processes involved in climate change and land use and its impact on water systems. In this context, the objective of this study was to simulate climate change scenarios combined with the land use change and to analyze the impacts on the hydrology in the Piracicaba basin. Two periods were selected based on the preliminary result of detection of the abrupt change point of the annual flow series, using Petitt's non-parameter test. The first period selected prior to the occurrence of the point of the change was from 1985 to 2000. The other period after the point of the change was 2001 to 2015. Land use maps of the years 1990 and 2010 were used to represent the two periods. The results showed a good performance of the SWAT model. The NS (Nash-Sutcliffe coefficient) was 0.88 in calibration for both periods. In the validation, the NS was 0.92 and 0.94 for the first and second periods respectively. We then simulate climate and land use changes scenarios and compare them to the current scenario (baseline). The simulation results showed that the hydrological processes in the Piracicaba basin in the period 1985-2015, had more intense responses to land use change than climate.

Increased CO2 emissions and air pollution impact the environment and human health. In this manner, new functionalized polyaminal-based polymers are synthesized via a one-pot polycondensation reaction of melamine with aldehyde monomers 2-bromo-1-naphthaldehyde and 2-hydroxy-1-naphthaldehyde to yield bromine- hydroxyl- functionalized polymer networks PAN-BrNA and PAN-HNA, respectively. The polyaminals porosity parameters were investigated and applied as an adsorbent for CO2 capture. FTIR, solid-state 13C NMR, and X-ray diffraction verified the PANs structure development. A scanning electron microscope and N2 adsorption-desorption methods were utilized to identify the porous properties of the polymers at 77 K. The Brunauer-Emmett-Teller (BET) surface area of PAN-BrNA and PAN-HNA is (16.6990 m2/g) and (716.7568 m2/g), respectively. At 273 K, PAN-BrNA and PAN-HNA can take CO2 gas up to (4.42786 cm3/g) and (47.55 cm3/g), respectively. The findings show that inserting functional groups has a significant impact on surface area and porosity parameters, as well as CO2 uptake.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

The controllability and consistency in the fabrication of micro-textures on large-scale remains a challenge for existing production processes. Mask electrolyte jet machining (MEJM) is an alternative to Jet-ECM for controllable and high-throughput surface microfabrication with more consistency of dimensional tolerances. This hybrid configuration combines the high-throughput of masked-ECM and the adjustable flow-field of jet-ECM. In this work, a duckbill jet nozzle was introduced to make MEJM more capable of batch micro-structuring. A multiphysics model was built to simulate the distribution of electrochemical reaction ions, the cur- rent density distribution and the evolution of the shape of the machined cavity. Experimental investigations are presented showing the influence of the machining voltage and nozzle moving speed on the micro cavity. Several 35 ×35 micro cavity arrays with a diameter of 24.92 − 11.73 µm and depth of 15.86 − 7.24 µm are generated on 304 stainless steel.

Polymer materials are increasingly being used for sliding machine elements due to their numerous advantages. They are used even where they are deformed and in such a state they interact frictionally e.g. in machine hydraulics or lip seals. Few publications deal with the influence of deformation, which is the effect of e.g. assembly on tribological properties of polymeric material. This deformation can reach up to ε ≈ 20% and is achieved without increasing the temperature of the polymer material. The paper presents the results of investigations in which high-density polyethylene (PE-HD) was maintained in deformation by means of a special grip (holder). The wear of the sample was significantly higher than that of the undeformed sample. This effect persisted even after partial relaxation of the stress in the sample after 24 hours. Additional investigations were carried out to explain the obtained results. There were the microscopic observations of the surface after friction, measurements of microhardness and free surface energy. Changes in the value of surface free energy and a significant decrease in microhardness with deformation under tension were observed. Strained material had a different surface appearance after friction and a different size and form of wear products. It was indicated that it is probable that the cohesion of the material will decrease and that the character of the wear process will change as a result of tension. Tension without heating of polymeric material (PE-HD), e.g. as a result of assembly, has been qualified as a hazard to be taken into account when designing and analysing polymeric sliding elements.

In this work, the wetting and evaporation behaviour of non-polar solvent droplets on thin soluble coatings is investigated experimentally. The wetting process on spin coated polymer layers by the solvent is captured using shadowgraphy. Initial spontaneous dynamic wetting as well as later stages of wetting are recorded and evaluated. Furthermore, structures obtained by wetting and subsequent evaporation of solvents on polymer coatings are studied by confocal microscopy. The solubility of the substrate has been varied by using polymers with different molecular masses. We observe that initial spreading dynamics does not depend on the molar mass in the studied range. However, we find a strong influence of the molar mass on the late stage wetting dynamics and on the surface structure after solvent evaporation.

MIPs inspired by antigen-antibody interactions have received substantial interest as a biomimetic artificial receptor system in environmental applications. Herein, we present a molecularly imprinted surface plasmon resonance (SPR) sensor integrated with Au nanoparticles for the identification of bisphenol A (BPA), an endocrine-disrupting chemical. The synthetic wastewater samples were analyzed to ensure the method's reliability and feasibility. Under ideal conditions, the suggested approach performed well in terms of analytical performance to BPA, with a wide linear range of 0.1 to 10 ppb and LOD of 10 ng/L. The sensor results and the Langmuir adsorption model have good agreement. It has also been shown that repeated use of the biosensor can be achieved. According to selectivity studies, BPA adsorbed within the imprinted cavities favorably compared to 4-nitrophenol and phenol. The produced BPA-imprinted SPR sensor provides improved sensitivity based on the signal amplification strategy, unconjugated sensing without the need for labeling, real-time sensing, low sample consumption rates, quantifiable assessment, and very good kinetic rate constant calculation in actual samples. Also, because the produced sensor is reusable with relative standard deviations (RSD)<1.25, indicating the sensor's accuracy, the SPR-based biomimetic BPA sensor is simple to practice and may be an economical option.

Taking a typical forest underlying surface as the research area, this study employed the unmanned aerial vehicle (UAV) photogrammetry to explore more accurate canopy parameters including tree height and canopy radius, which were used to improve the Noah-MP land surface model conducted in Dinghushan Forest Ecosystem Research Station (CN-Din). While the canopy radius was fitted as a Burr distribution, the canopy height of CN-Din forest followed a Weibull distribution. The replacement of the parameters by these observed UAV would result in the Noah-MP model. It was found that the influence on the simulation of the energy fluxes could not be negligible, and the main influence of these canopy parameters was on the latent heat flux which could decrease up to -11% in the midday while increase up to 15% in the nighttime. Additionally, this work indicated that the description of the canopy characteristics for the land surface model should be improved to accurately deliver the heterogeneity for the underlying surface.

Once on Mars, maintenance and repair will be crucial for humans as supply chains including Earth andMars will be very complex. Consequently, the raw material available on mars must be processed and used. Factors such as the energy available for material production play just as important a role as the quality of the material that can be produced and the quality of its surface. With the aim of developing and technically implementing a process chain that meets the challenge of producing spare parts from oxygen-reduced Mars regolith, this paper addresses the issue of low-energy handling. Expected statistically distributed high roughnesses of sintered regolith analogs are approximated in this work by parameter variation in the PBF-LB/M process. For low-energy handling, a dry-adhesive microstructure is used. Investigations are carried out to determine the extent to which the rough surface resulting from the manufacturing process can be smoothed by deep rolling in such a way that the microstructure adheres and enables samples to be transported. For the investigated AlSi10Mg samples (12 mm x 12 mm x 10 mm), the surface roughness varies in a wide range from Sa 7.7 µm to Sa 64 µm after the additive manufacturing process, pull-off stresses of up to 6.99 N/cm² could be realized after deep rolling. This represents an increase in pull-off stresses by a factor of 392.94 compared to the pull-off stresses before deep rolling, enabling handling of even larger specimens. It is noteworthy that specimens with roughness values that were previously difficult to handle can be treated post-deep rolling, indicating a potential influence of additional variables that describe roughness or ripples and are associated with the adhesion effect of the microstructure of the dry adhesive.

High surface area carbon was obtained from -carrageenan – urea cryogels doped with 1.25 – 5 wt% graphene oxide (GO). Incorporation of GO resulted in multifaceted modification in the textural and chemical properties of the carbon cryogel. The thermal decomposition of GO facilitated the formation of micropores resulted in a substantial increase in the apparent surface area (up to 1780 m2/g). The annealing at 1000 °C removed part of the heteroatoms but left behind a high number of defects. While the volatile thermal degradation products of GO affected the porous texture and the surface chemistry in a complex way, its reduced residue resulted in a gradually increasing electrical conductivity. The influence of GO was studied in oxygen reduction reaction (ORR) and in Li-ion storage application. GO affected the electron transfer mechanism in the ORR tests and challenged the stability of the electrodes. Even if the electrode has been stabilized under oxygen-free conditions, later may undergo destabilization processes during the ORR. The 5 wt% GO doped sample was the most sensitive under oxidative conditions, but finally it exhibited the highest capacitance. In the Li-ion battery tests the coulombic efficiency of all the samples was consistently above 98 %, indicating the great potential of such carbons for efficient Li-ion insertion and reinsertion during the charge – discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25% sample showed an initial discharge capacity of 313 mAh/g, 95.1 % capacity retention and 99.3 % coulombic efficiency after 50 charge – discharge cycles.

The objective of this study is to evaluate the effects of the 3D point cloud density derived from unmanned aerial vehicle (UAV) photogrammetry and structure from motion (SfM) and multi-view stereopsis (MVS) techniques, the interpolation method for generating a digital terrain model (DTM), and the resolution (grid size) of the derived DTM on the accuracy of estimated heights in small areas, where a very accurate high spatial resolution is required. A UAV-photogrammetry project was carried out on a bare soil of 13 × 13 m with a rotatory wing UAV at 10 m flight altitude (equivalent ground sample distance = 0.4 cm). The 3D point cloud was derived, and five sample replications representing 1, 2, 3, 4, 5, 10, 15, 20, 30, 40, 50, 60, 70, 80 and 90% of the original cloud were extracted to analyze the effect of cloud density on DTM accuracy. For each of these samples, DTMs were derived using four different interpolation methods (Inverse Distance Weighted (IDW), Multiquadric Radial Basis Function (MRBF), Kriging (KR), and Triangulation with Linear Interpolation (TLI)) and 15 DTM grid size (GS) values (20, 15, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0.67, 0.5, and 0.4 cm). Then, 675 DTMs were analyzed. The results showed, for each interpolation method and each density, an optimal GS value (most of the cases equal to 1 cm) for which the Root Mean Square Error (RMSE) is minimum. IDW was the interpolator which yielded best accuracies for all combination of densities and GS. Its RMSE, considering the raw cloud, was 1.054 cm. The RMSE increased 3% when a point cloud with 80% extracted from the raw cloud was used to generate the DTM. When the point cloud included the 40% of the raw cloud, RMSE increased 5%. For densities lower than 15%, RMSE increased exponentially (45% for 1% of raw cloud). The grid size minimizing RMSE for densities of 20% or higher was 1 cm, which represents 2.5 times the ground sample distance of the pictures used for developing the photogrammetry project.

In the present study, Electrocoagulated Metal Hydroxide Sludge (EMHS) was analyzed as adsorbent material to remove both fluoride ion (F-) and arsenic V (As(V)) from aqueous effluents. This material was generated during an electrocoagulation process using Aluminum anode. It was characterized by using specific surface areas and the surface morphology was studied by scanning electron microscopy (SEM). Adsorbent fixed-beds are generally studied to remove different class of contaminants. EMHS was evaluated using a continuous flow rate column test with an experimental design. The effect of initial concentration of F- (2.5–10 mg L⁻¹) and the Empty Bed Contact Time (EBCT (0.4–0.8 min)) was studied following a central composite design methodology. The experimented parameters had a significant influence on saturation time, breakthrough volume, and breakthrough time. A response surface analysis was a tool for analyzing the adsorption study, showing interactions that are complicated to identify by others methods. The results, here reported, revealed that EMHS is an efficient and promising adsorbent material in order to remove F- and As(V) from water contaminated by these pollutants.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Land surface albedo determines the splitting of downwelling solar radiation into components which are either reflected back to the atmosphere or absorbed by the surface. Land surface albedo is an important variable for the climate community and therefore was defined by the Global Climate Observing System (GCOS) as an Essential Climate Variable (ECV). Within the scope of the Satellite Application Facility for Land Surface Analysis (LSA SAF) of EUMETSAT, a near-real time (NRT) daily albedo product was developed in the last decade from observations provided by the SEVIRI instrument on board the geostationary satellites of the Meteosat Second Generation (MSG) series. In this study we present a new collection of albedo satellite products based on the same satellite data. The MSG Ten-day ALbedo (MTAL) product incorporates MSG observations over 31 days with a frequency of NRT production of 10 days. The MTAL collection is more dedicated to climate analysis studies compared to the daily albedo that was initially designed for the weather prediction community. For this reason, a homogeneous reprocessing of MTAL was done in 2018 to generate a Climate Data Record (CDR). The resulting product is called MTAL-R and has been made available to the community in addition to the NRT version of the MTAL product which has been available for several years. The retrieval algorithm behind the MTAL products comprises three distinct modules: one for atmospheric correction, one for daily inversion of a semi-empirical model of the bidirectional reflectance distribution function, and one for monthly composition that also determines surface albedo values. In this study the MTAL-R CDR is compared to ground surface measurements and concomitant albedo products collected by sensors on-board polar-orbiting satellites (SPOT-VGT and MODIS). We show that MTAL-R meets the quality requirements if MODIS or SPOT-VGT are considered as reference. This work leads to 14 years of production of geostationary land surface albedo products with a guaranteed continuity in the LSA SAF for the future years with the forthcoming third generation of European geostationary satellites.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Coalescence of nanowires and other three-dimensional structures into continuous film is desirable for growing low dislocation density III-nitride and III-V materials on lattice-mismatched substrates, and interesting from the fundamental viewpoint. Here, we develop a growth model for vertical nanowires which, under rather general assumptions on the solid-like coalescence process within the Kolmogorov crystallization theory, results in a morphological diagram for the asymptotic coverage of a substrate surface. The coverage is presented as a function of two variables, the material collection efficiency on the top nanowire facet a, and the normalized surface diffusion flux of adatoms from the NW sidewalls b. The full coalescence of nanowires is possible only when a=1 regardless of b. At a&gt;1, which is usual for vapor-liquid-solid growth with a catalyst droplet, nanowires can only partly merge but never coalesce into continuous film. These results can be used for predicting and controlling the degree of surface coverage by nanowires and three-dimensional islands by tuning the surface density, droplet size, adatoms diffusivity, and geometry of the initial structures in the vapor-liquid-solid, selective area or self-induced growth processes in different epitaxy techniques.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Sea ice surface roughness affects ice-atmosphere interactions, serves as an indicator of ice age, shows patterns of ice convergence and divergence, affects the spatial extent of summer melt ponds, and ice albedo. We have developed a method for mapping sea ice surface roughness using angular reflectance data from the Multi-angle Imaging SpectroRadiometer (MISR) and lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). Using an empirical data modeling approach, we derived estimates of Arctic sea ice roughness ranging from centimeters to decimeters meters within the MISR 275-m pixel size. Using independent ATM data for validation, we find that histograms of lidar and multi-angular roughness values are nearly identical for areas with roughness <20 cm but that for rougher regions, the MISR-derived roughness has a narrower range of values than the ATM data. The algorithm is able to accurately identify areas that transition between smooth and rough ice. Because of its coarser spatial scale, MISR-derived roughness data have a variance of about half that ATM roughness data.

Wetting of deformable substrates has gained significant interest over the past decade due to its extensive applications and uses. This interest has developed due to technological advances which are able to capture interfacial behavior taking place when a liquid droplet is placed on a deformable substrate. Researchers have developed different theories to explain processes taking place in the process of wetting of deformable/soft substrates. For the scope of this review, we will consider the fluid to be Newtonian, partially wetting, and surface forces are incorporated with the help of disjoining/conjoining pressure acting in the vicinity of the apparent, three-phase contact line. The following subjects are briefly reviewed: (i) Equilibrium of droplets on soft substrates. It is shown that properties of the disjoining/conjoining pressure isotherm and properties of the deformable substrate determine both the shape of the liquid droplet and deformation of the substrate; (ii) Equilibrium conditions of droplets on deformable substrates. It is shown that for a droplet to be at equilibrium on a deformable substrate under consideration, Jacobi’s sufficient condition is satisfied; (iii) Hysteresis of contact angle of sessile droplets on deformable substrates. It is shown that as the elasticity of the deformable substrate is increased, both advancing and receding contact angles are reduced.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

The paper presents the results of the study of tungsten surface structure modification under helium plasma irradiation. It is revealed that during irradiation of samples, surface modification in the form of relief development as a result of irradiation is observed. X-ray phase analysis showed that no new phases of the W system were found after irradiation, only an increase in the intensity of diffraction lines was observed. There are significant differences in the microstructure of tungsten depending on the temperature of helium plasma irradiation in the above range. It is assumed that the cause of defects is the extremely low solubility of helium in tungsten. Metallographic analysis has shown that at irradiation of tungsten samples in regime 5 and 6 the degree of relief development is not high in comparison with the tungsten sample irradiated in regime 4. The greatest increase in roughness of the sample irradiated in regime 5 was determined, which is associated with the formation of small cracks, blisters and pores in the surface layer. At the same time, in the samples irradiated in regime 6, the surface of which is characterized by chaotically located protrusions and depressions of various shapes, the roughness parameter Ra was 0.0603 µm. It was found that at temperature regimes T = 1200 °C and T = 1500 °C the microhardness of tungsten increases by 11% and 10% respectively.

This study explores wind energy resources in different locations through the Gulf of Oman and also their future variability due climate change impacts. In this regard, EC-EARTH near-surface wind outputs obtained from CORDEX-MENA simulations are used for historical and future projection of the energy. The ERA5 wind data are employed to assess the suitability of the climate model. Moreover, the ERA5 wave data over the study area are applied to compute sea surface roughness as an important variable for converting near-surface wind speeds to those of wind speed at turbine hub height. Considering the power distribution, bathymetry and distance from the coats, some spots as tentative energy hotspots to provide a detailed assessment of directional and temporal variability and also to investigate climate change impact studies. RCP8.5 is a common climatic scenario is used to project and extract future variation of the energy in the selected sites. The results of this study demonstrate that the selected locations have a suitable potential for wind power turbine plans and constructions.

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

Giant plasmonic surface enhancement has been observed in gold coated micron sized inverse pyramids entrapping a gold nanoparticle. The amplification of both surface enhanced Raman and photoluminescence signals was found to be dependent on the diameter of trapped gold nanoparticle and around 50-fold enhancement was detected for 250nm diameter sample relatively to the 50nm one. Finite differential time domain simulations, performed to determine the near-field distribution in the structure, showed that when the nanoparticle protrudes into the hotspot zone of the void, coupling of electromagnetic field occurs and the plasmon-related near-field enhancement is concentrated into the close vicinity of the nanoparticle, mainly into the close gaps around the tangential points of the curved sphere and the flat pyramid surface. This results in a more than 15 times increase of the near-field intensity, compared to the empty void.

Hydrogeological maps must synthesize the scientific knowledge about the hydraulic features and the hydrogeological behavior of a specific area, and, at the same time, they must meet the expectations of land planners and administrators. Thus, especially in complex interconnected systems, hydrogeological maps can be fully effective when they are purpose-designed. In these contexts, usual graphical approaches in creating hydrogeological maps could result uncomplete and/or ineffective. Therefore, in case of complex systems and/or specific management/protection aims, new and purpose-designed graphical solutions must be applied to enhance the maps effectiveness. In the case study, these solutions show and emphasize all the hydraulic interconnections playing significant roles in recharging the multilayered alluvial aquifer, where the majority of wells have been drilled for drinking/industrial/agricultural purposes, artificial channels are used for agricultural purposes, and the shallow groundwater feeds protected groundwater-dependent-ecosystems. The hydrogeological map was then designed to be the synthesis of three different and hydraulically interconnected main contexts: (i) the main heterogeneous alluvial aquifer (the main target of the purpose-designed map), (ii) the hydrographic basin of a losing river that feeds the main alluvial aquifer, and (iii) those hard-rock aquifers (mainly turbiditic and ophiolitic) whose springs feed the same river.

Regional heat capacity change is calculated from the ratio between the addition or subtraction of heat (ΔQ) with the increase or decrease in temperature (ΔT) region. The purpose of this study is to calculate the regional heat capacity change due to the changes of land cover composition with forest, shrubs, oil palm plantation and bare soil using Landsat-5 TM satellite data on 1994, 2000 and 2010. Total area that used on ​​this study is 12971 ha. In 1994-2000, 4 % of forest area and 2% shrubs were increased, followed by additional of biomass forest 4.01 tons/ha and 2.83 tons/ha for shrubs. The increased of forest area and biomass (tons/ha) caused by forest and shrubs growth processing towards climax that added the canopy volume. So that, the regional heat capacity in 1994 amounted 19384 MJC^o-1 increased to 19929 MJC^o-1 in 2000. Data observation for 2000-2010 showed that forest area decreased by 66% due to forest’s clearing into oil palm plantations (47%), shrubs (8%) and bare soil (11%). But, plant’s biomass continue to increased, i.e 1.48 ton/ha for forest, 2.73 tons/ha for shrubs and 4.63 tons/ha for bare soil. Before 2000, there was no land cover by oil palm plantations, so the increasing rate from this land was the biggest than the three other lands, amounting to 122.29 tons/ha. Decreasing in the percentage of forest area does not cause a decrease in the heat capacity of the region. Intensive maintenance on oil plam plantation such as water management, fertilizer and planting space made it biomass productivity and ability to save the heat is greater than the forest. As the result, in 2010 regional heat capacity increased to 22508 MJC^o-1.

Background: Implant surface topography is a key element in achieving osseointegration. Nanostructured surfaces have shown promising results in accelerating and improving bone healing around dental implants. The main objective of the present clinical and histological study is to compare, at 4 and 6 weeks, (w) bone-to-implant contact in implants having either machined surface (MAC), SLA medium roughness surface or a Nanostructured Calcium-Incorporated sur-face (XPEED®). Methods: 35 mini-implants with 3 different surface treatments (XPEED® (n=16) – SLA (n=13) – Machined (n=6), were placed in the posterior maxilla of 11 patients then, retrieved at either 4 or 6w in a randomized split-mouth study design. Results: The BIC rate measured at 4 and 6w respectively, was: 16.8 % (±5.0) and 29.0 % (±3.1) for MAC surface; 18.5 % (±2.3) and 33.7 % (±3.3) for SLA surface; 22.4 % (±1.3) and 38.6 % (±3.2) for XPEED® surface. In all types of in-vestigated surfaces, the time factor appeared to significantly increase the BIC rate (p < .05). XPEED® surface showed a significantly higher values when compared to both SLA and MAC values at 4w (p < .05). Also, at 6w, both roughened surfaces (SLA and XPEED® ) showed signifi-cantly higher values (p < .05) than turned surface (MAC). Conclusion: Nanostructured Calcium titanate coating is able to enhance bone deposition around implants at early healing stages.