Solar and wind resources available for power generation are subject to variability due to meteorological factors. Here, we use a new global climate reanalysis product, Version 2 of the NASA Modern-Era Retrospective Analysis for Research and Applications (MERRA-2), to quantify interannual variability of monthly-mean solar and wind resource from 1980 to 2016 at a resolution of about 0.5 degrees. We find an average coefficient of variation (CV) of 11% for monthly-mean solar radiation and 8% for windspeed. Mean CVs were about 25% greater over ocean than over land, and, for land areas, were greatest at high latitude. The correlation between solar and wind anomalies was near zero in the global mean, but markedly positive or negative in some regions. Both wind and solar variability were correlated with values of climate modes such as the Southern Oscillation Index and Arctic Oscillation, with correlations in the Northern Hemisphere generally stronger during winter. We conclude that reanalysis solar and wind fields could be helpful in assessing variability in power generation due to interannual fluctuations in the wind and solar resource. Skillful prediction of these fluctuations seems to be possible, particularly for certain regions and seasons, given persistence or predictability of climate modes with which these fluctuations are associated.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Our environment has been impacted by man-made pollutants mainly industries make substantial use of synthetic dyes which exhibit cytotoxicity and have significant environmental consequences. Effective photocatalyst-based approaches for degrading synthetic dyes into less toxic chemical are of great interest. Synthesizing NPs using biological approaches, particularly plant-based approaches offer advantages, decreasing the risk of NPs losing biocompatibility during synthesis, cost-effectiveness, and eco-friendliness. In this study, we employed a green synthesis method to produce manganese oxide nanoparticles (MnO NPs) utilizing leaf extract from the Lathyrus Aphaca plant. The synthesized MnOx NPs were characterized through various techniques; X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier-transform infrared spectroscopy (FTIR), and UV–visible spectroscopy. XRD analysis showed distinct peaks, indicated the presence crystallographic planes within the MnO₂ nanoparticles, thus confirming their crystalline structure. SEM study highlighted closely packed configurations with average size of approximately ≥ 50-70 nm, with well-defined boundaries. EDX analysis showed the presence of elemental manganese (Mn) in the samples, with peaks corresponding to Mn detected at lower energy levels, predominantly represented by MnO. FTIR, showed the presence of the O-O stretching mode at a frequency of 719 cm^-1, the presence of MnO₆ oxides of manganese, and peak at 548 cm^-1 corresponded to the Mn-O stretching mode. Furthermore, the green-synthesized manganese oxide nanoparticles exhibited promising photocatalytic and adsorption capabilities against Methylene Blue (MB) dye, leading to approximately 93.21% degradation of MB when treated with the green-synthesized MnO nanoparticles derived from plant extract. This highlights the efficacy and potential of these nanoparticles in environmental remediation applications, particularly in the degradation of methylene blue contaminants.

Radical reactions in water or aqueous media are important for organic synthesis, realizing high yielding processes under non-toxic and environmentally friendly conditions. This overview includes (i) a general introduction to organic chemistry in water and aqueous media, (ii) synthetic approaches in-, on- and with-water as well as in heterogeneous phase, (iii) reaction of carbon-centered radicals with water (or deuterium oxide) activated through coordination with various Lewis acids, (iv) photocatalysis in water and aqueous media, and (v) synthetic applications bioinspired from naturally occurring processes. A wide range of chemical processes and synthetic strategies under different experimental conditions have been reviewed that lead to important functional group translocation and transformation reactions, leading to the preparation of complex molecules. These results reveal how water as a solvent/medium/reagent in radical chemistry has matured over the last two decades and how further discoveries are foreseen to come in the near future.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

Our analysis of previous studies shows that solar energy and wind can consume negligible amount of water to generate one megawatt of electricity.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Space exploration introduces astronauts to many challenges such as space radiation and microgravity. Researchers have investigated vitamin C as a potential radiation mitigator and antioxidants for sustaining astronaut health. Building on our own studies, which indicate vitamin C's life-saving radioprotective effects and its potential as a radiation mitigator, our research highlights its promise, even when administered 24 h post-exposure. This is particularly relevant in scenarios where astronauts may be exposed to sudden large solar particle events, potentially resulting in lethal doses of space radiation. The success of vegetable cultivation on the International Space Station using NASA's Veggie system offers fresh, vitamin C-rich food. While approved supplements address somatic function, further research is needed to optimize vitamin C's efficacy in humans and develop antioxidant cocktails for space missions. The variable vitamin C content in vegetables underscores the necessity for utilization of artificial intelligence (AI) to assist astronauts in selecting and cultivating vitamin C-rich vegetables that are best suited to combat high levels of space radiation and microgravity. Particularly, AI algorithms can be utilized in analyzing various factors such as nutritional content, growth patterns, and cultivation methods. In conclusion, vitamin C shows significant potential for mitigating space radiation, and ongoing research aims to enhance astronaut health through optimal dietary strategies.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

We investigated the liquid water path and global solar irradiance at ground (Q) according to the ICON model, CLOUDNET measurements in Lindenberg, Munich, Jülich, and BSRN observations in Lindenberg. The liquid water path is underestimated, while global irradiance is overestimated. The lower liquid water path is due to liquid water content underestimation practically in all atmosphere layers and lower frequency of liquid clouds occurrence compare to observations. The latter is partly associated with a reduced model’ sensitivity to the cloud condensation nuclei (CCN). An increase in CCN from 250 cm-3 (typical background value for the region of interest) to 1700 cm-3 (characteristic of polluted continental clouds) leads to an increase in grid-scale liquid water path by 40% and a decrease in Q under overcast conditions by 12%. However, we also showed that liquid water path is not a key factor of Q overestimation. The main factor is an inaccurate description of the cloud spatial structure, where the correct prediction of the direct to global irradiance ratio as a spatial characteristic of clouds plays the most important role compared to standard cloud fraction.

The presented work studies the processes of synthesis of nitrogen-containing structures of ZnO using atmospheric pressure microwave nitrogen plasma and investigates their photocatalytic activity in the processes of degradation of 2,4-dinitrophenol and the antibiotic ciprofloxacin when irradiated with sunlight. The work proposes an effective method for formation of photosensitive ZnO powders. Due to the features of plasma treatment in the open atmosphere of zinc metal microparticles, ZnO structures are formed with sizes from hundreds of nanometers to several micrometers with various micromorphologies. High photoactivity was demonstrated (rate constants 0.036 min-1 and 0.051 min-1) of synthesized ZnO structures during photo-degradation of 2,4-dinitrophenol and ciprofloxacin, respectively, when exposed to solar radiation. Photo-active structures of ZnO synthesized using microwave nitrogen plasma can find application in processes of mineralization of toxic organic compounds.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

The solar cell industry is a part of the green energy sector, and effectively combining the patents of various manufacturers within the supply chain to collectively create sustainable patent market value is of paramount importance. This study aimed to establish a business strategy framework for Project-based licensing through the analysis of solar cell patents and the integration of supply chain manufacturers' patents, with the goal of collectively creating market value for patents sustainably. The research methodology included literature analysis and focus group discussions. Initially, the study analyzed solar cell industry patents from the past decade using the WIPS Global Patent database to identify projects with the highest patent count. Subsequently, through the use of focus group discussions, the feasibility of a patent pool strategy within the supply chain was explored. Finally, a strategy framework was proposed for Project-based patent pool licensing, focusing on the top 15 projects with the highest count of 5,579 patents. The results indicated that adopting this strategy framework for supply chain manufacturer patents can result in higher commercial patent value.

Developing low-cost and stable materials for converting solar energy into electricity is vital in meeting the world's energy demand. Metal-organic frameworks (MOFs) have gained attention for solar cells due to their natural porous architectures and tunable chemical structures. This review commences with an exploration of the synthetic methods of MOFs. Moreover, we discuss the various roles of MOFs, including photoanodes and counter electrodes in dye-sensitized solar cells and interfacial layers and charge carriers in perovskite solar cells. Ultimately, burdensome tasks and possible directions for advancing MOFs-based nanomaterials are provided for solar cells.

Copper-nitride (Cu3N) material is attracting much attention as a potential next-generation thin-film solar-light absorber. In this work, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron sputtering, at room temperature,onto glass and silicon substrates. The optical properties of the Cu3N thin layers were studied by spectroscopic ellipsometry and transmission, to achieve a low-cost absorber material to replace conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by FIB-SEM microscopy and FTIR spectroscopy.

In this paper, solar irradiance and wind speed forecasts were performed considering time horizons ranging from 10 min to 60 min, under a 10 min time-step. Global horizontal irradiance (GHI) and wind speed were computed using four forecasting models (Random Forest, k-Nearest Neighbours, Support Vector Regression, and Elastic Net) to compare their performance against two alternative dynamic ensemble methods (windowing and arbitrating). Forecasting models and dynamic forecasting ensembles were implemented in Python for performance evaluation. The performance comparison between the prediction models and the dynamic ensemble methods was carried out by evaluating the RMSE, MAE, R² and MAPE, to evaluate whether the dynamic ensemble forecasting method obtained greater. According to the results obtained windowing dynamic ensemble method was the most efficient among the tested. For the wind speed data, by varying its parameter λ (from 1 to 100), a variable performance profile was obtained, where from λ =1 to λ = 74, windowing proved to be the most efficient, reaching maximum efficiency for λ = 19. Windowing was the best method for the GHI analysis, reaching its best performance for λ = 1. The efficiency gain using windowing was 0.56% when using the wind speed model and 1.96% for GHI.

Nearly Zero Energy Buildings (NZEBs) play a key role in the world energy transition and this is motivating the scientific community to develop innovative electrical and thermal systems, characterized by very high efficiency to specifically address the energy needs of modern buildings. Naturally, the integration on buildings of latest generation PV-systems helps to satisfy this need and, having in mind this objective, an innovative and highly efficient BIPV-system is presented and discussed in this paper. First, the proposed PV-system is purpose-built to be fully integrated into a variety of buildings and, preferably, into their rooftop. It is based on a certain number of innovative rotating and bifacial PV-modules which are specifically made to be installed “under-glass”, within a likewise custom-made transparent casing. Each of the aforementioned PV-module has the form of single row of bifacial PV-cells and is equipped with two special terminations; the PV-modules are then installed inside their transparent casing, side by side and suitably spaced from each other. Thanks to the aforementioned properties, the PV-modules can rotate around their central longitudinal axis, by using a very low-power, reliable and efficient mono-axial solar tracking system. Finally, by the aforementioned way, the proposed PV-system assumes – de facto - the form of a transparent BIPV-generator (PV-skylight), equipped with an innovative “under-glass” single axis solar tracking system. Once the proposed PV-generator is fully integrated into a building, it generates electricity and, additionally, helps to improve both the whole energy performances and the aesthetic appearance of the building. The electricity generation and illuminance performances of the proposed BIPV-generator are experimentally tested by using a low-power home-made prototype driven by different solar tracking logics and under different operating conditions; the most relevant results are summarized and extensively discussed.

Load forecasting is an important component of power system and resource planning for electrical grids. The adoption of electric vehicles (EVs), behind-the-meter (BTM) solar, and heat pumps will significant change the amount and variability of loads. Electrification adoption and load forecasting in arctic regions and Alaska is limited. This paper provides the first load and electrification adoption forecast for the Alaska Railbelt transmission system, including yearly adoption rates of EVs, BTM solar, and heat pumps and hourly load data. Adoption rates are based on available historical data and compared to other regional and national trends. Two forecasts are created: 1) a moderate adoption forecast based on projections from current adoption rates and comparisons to other projections, and 2) an aggressive forecast, which provides a bookend comparison at the high adoption rate of 90% for all technologies. The results of these forecasts demonstrate a significant increase in both energy, 80% and 116% for moderate and aggressive, respectively and peak load demand, 113% and 219% for moderate and aggressive, respectively. Additionally, the results indicate a maximum hourly load change of 260% and 381% for the moderate and aggressive forecasts, respectively. These findings highlight a need for resource planning, which accounts for increases in demand and suggests that significant demand management is needed to smooth and control the load fluctuations as a result of the adoption of EVs, BTM solar, and heat pumps.

Solar pavement technology has numerous benefits for advanced life and environmental protection, including reduced fossil fuel usage, reduction harmful emissions from conventional electricity generation and handy reliable electricity via solar energy. This paper aims to find an alternative for cost effective renewable energy sources is in conjunction with the principles of sustainability. This research studies whether the application of thermal energy harvesting road pavement using sustainable conductive piping such as stainless steel, copper, and aluminium are feasible in Malaysia. The scope of the paper is to optimize the suitable parameters for different materials of thermal energy harvester such as pipe material, pipe depth inserted into pavement, types of pipe arrangement, pipe spacing, and flow rate for maximum thermal energy extraction using numerical simulation. The simulation is testing under engineering software ANSYS Workbench 19.2 (Fluent) and Solidworks 2020 to develop project prototype from optimize thermal energy harvester. Thus, serpentine copper pipe shows the highest heat efficiency which is 32.22% with the temperature outlet of 327.35K (54.21°C) at the pipe located at 50 mm from the surface pavement with the pipe spacing of 80 mm centre-to-centre.

The fractal dimension of geomagnetic variations at the Baigazan magnetic station at Russian Altay for 2011-2013 was calculated using the Higuchi method. The daily variation of Higuchi Fractal Dimension (HFD) for the D,H,Z-components of the geomagnetic field has been investigated, its contribution to the variability of HFD is from 30 to 40 percent of the total variance. A correlation analysis of the fractal dimension of the variations of the D,H,Z-components with Auroral Electrojet (AE) index and solar wind characteristics was carried out. A negative correlations with logarithms of AE-index, interplanetary magnetic field (IMF) strength and solar wind velocity were found. About 25 percent of the fractal dimension variance is controlled by the variability of these characteristics. Pair and partial correlation coefficients for these parameters were calculated for every month of 2011-2013.

In this work, we compiled our research on lanthanide-based luminescent materials, prepared down-shifter layers, and studied their effect on photovoltaic (PV) mini-modules. The compounds we have prepared (C1-C17), with formulas [Eu2(phen)2(bz)6] (C1), [Eu2(bphen)2(bz)6] (C2), [Eu(tta)3bphen] (C3), [Eu(bta)3pyz-phen] (C4), [Eu(tta)3pyz-phen] (C5), [Eu(bta)3me-phen] (C6), [Er(bta)3me-phen] (C7), [Yb(bta)3me-phen] (C8), [Gd(bta)3me-phen] (C9), [Yb(bta)3pyz-phen] (C10), [Er(tta)3pyz-phen] (C11), [Eu2(bz)4(tta)2(phen)2] (C12), [Gd2(bz)4(tta)2(phen)2] (C13), [EuTb(bz)4(tta)2(phen)2] (C14), [EuGd(bz)4(tta)2(phen)2] (C15), [Eu1.2Gd0.8(bz)4(tta)2(phen)2] (C16) and [Eu1.6Gd0.4(bz)4(tta)2(phen)2] (C17), can be grouped into three families based on their composition: Series C1–6 were synthesized using Eu3+ ions and phenanthroline derivatives as the neutral ligands, and fluorinated β-diketonates as the anionic ligands. Complexes C7–11 were prepared with ligands similar to those of compounds C1–6 but were synthesized with Er3+, Yb3+, or Gd3+ ions. Series C12–17 exhibit the general formula [M1M2(bz)4(tta)2(phen)2], where M1 and M2 can be Eu3+, Gd3+, or Tb3+ ions, and the ligands are benzoate (bz–), 2-thenoyltrifluoroacetone (tta–) and 1,10–phenanthroline (phen). All compounds were characterized using X-ray techniques, and their photoluminescent properties were studied. We then examined their impact on the EQE (External Quantum Efficiency) of PV mini-modules and their durability in a climate chamber when embedded in PMMA and EVA films. This review emphasizes the methodology employed and the key findings, including enhanced mini-module efficiency. Additionally, we present promising results on the application of compound C6 in a bifacial solar cell.

This paper focuses on the impact of defects density and carrier capture cross-section area in the electron transport material (ETM), hole transport material (HTM), and absorber layers on the performance of perovskite solar cells and quantum efficiency (QE). Furthermore, the impact of defects density at the interface between ETM/absorber and absorber/HTM is also studied. SCAPS-1D software is used in the current study in determining solar cell performance. The proposed perovskite solar cell structure is a planar FTO/TiO2/ CH3NH3PbI3/ Cu2O. The results indicated that increasing the defect density in the absorber layer significantly affects cell performance, while in ETM and HTM layers, the cell parameters remain unaffected. It is also found that the defect capture cross-section has a similar behavior to the defect density in the main layers (ETM, absorber, and HTM). In addition, it is observed that by increasing the defects density in the ETM/absorber and absorber/HTM interfaces layer, the cell parameters FF, Jsc, and PCE have been slightly decreased, with no effect on Voc. Moreover, it is also noted that the quantum efficiency QE is sharply reduced. Finally, this paper introduced the correlation between the defect density and the capture cross-section, which is the first attempt to find such a relationship in perovskite solar cells to the knowledge of the authors.

The emergence of Non-Ionizing Radiation (NIR) has stimulated the growth and advancement of technological civilization. NIR is ubiquitous; it has helped improve all fields and even deepened democratic processes through the transfer of data and electronic transmission of results etc. A breathtaking part of NIR is its recent application in the treatment of adverse health effects through radiofrequency ablation, phototherapy, etc. as summarized in Table 1. The benefits of NIR are enormous, however, technological civilization has not come without a cost; some of the adverse health effects associated with NIR include skin cancers, sleep disorders, photo-aging, etc. as summarized in Table 2. Therefore, with the rapid and sporadic increase in the sources of NIR from Natural and Artificial sources including fossil fuel burning, Starlink technology, mobile phones, mobile base antennas, etc., background radiation is expected to rise beyond the exposure limit leading to health illnesses. Intrinsically, there is a dare need to marry concerns that evolve with this growth. Hence, this review article aims to congregate the health hazards associated with NIR and the state-of-the-art applications of NIR in medicine and the health sector in Nigeria being a developing country. Part of our recommendations is that the government at all levels should set up enforcement agencies and policies to drive strict adherence to NIR as provided by ICNIRP; frequent-periodic assessments of background radiation in public places should be carried out due to the increasing sources. In addition, further research is needed to ascertain the health hazard from emerging sources of NIR like Starlink technology and to substantiate findings of non-thermal effects.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 0.4 − 1 μm holes in alumina Al2O3 etch masks with 20-50 nm thickness. Such dielectric masks simplify fabrication of photonic crystal (PhC) light trapping patterns for the above-Lambertian performance of high efficiency solar cells. Conditions of laser ablation of transparent etch masks and effects sub-surface Si modifications were revealed by plasma etch- ing, numerical modeling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs-laser direct writing for dry plasma etch of Si.

Solar energy (SE) is essential for decarbonization of our economy and for energetic transition. Solar energy can be a sustainable economic activity as long as a balance is struck between the benefits it brings to climate change mitigation and the damage it can cause to biodiversity and ecosystems. Here we study this balance in an area with high biodiversity under pressure for installation of numerous photovoltaic plants (PPs). Our results show that developers give priority to the cheapest land close to connection points, while other values (e.g., environmental, landscape) are secondary. The regulatory process carried out by the Administration does not ensure the preservation of natural values, as several PPs with a high impact on important conservation areas have been approved. Experts' allegations provide quality information to the Administration to evaluate and demand changes to the projects presented. Such demands show that companies are willing to relocate plants to land occupied by olive groves. In this way, greater efficiency is achieved in land occupation, as well as shorter evacuation lines, water savings and less environmental impact. Prior strategic territorial planning could have avoided the impact of PPs already built, made the deployment of new PPs compatible with biodiversity conservation, and contributed to improving the management of key resources, such as subway aquifers. The proposed regulatory changes to the environmental assessment procedure (exclusion of renewables and public participation from the procedure) are detrimental, as they will make SE unable to meet the requirements of the Taxonomy Regulation.

As Alberta increases solar power generation, land use conflicts with agriculture increase. A solution that enables low-carbon electricity generation and continued (in some cases increased) agricultural output is the co-locating of solar photovoltaics and agriculture: agrivoltaics. This study reviews policies that impact the growth of agri-voltaics in Alberta. Solar PV-based electricity generation is governed by three regula-tions based on system capacity. In addition, agrivoltaics falls under various legisla-tions, frameworks, and guidelines for land utilization. These include Land Use Frame-work, Alberta Land Stewardship Act, Municipal Government Act, Special Areas Dis-position, Bill 22 and other laws/policies all of which are reviewed in the context of agrivoltaics. Several policies are recommended to support rapid diffusion of agrivolta-ics. First, open access research into agrivoltaics, which not only will help optimize agrivoltaic systems for the region, but also coupled with public education is expected to galvanize social acceptability of large-scale PV deployment. Clearly defining and categorizing agrivoltaic technology, developing agrivoltaic standards, making agri-voltaic technology-friendly regulations/frameworks and developing programs and pol-icies to incentivize agrivoltaic deployment over conventional PV will all accelerate dif-fusion. Through these measures, Alberta can achieve conservation and sustainability in food and energy sector while simultaneously addressing the renewable energy and climate-related goals.

This study reports an empirical analysis of an all-electric, Net Zero Energy Housing (NZEH) development located in a mixed-humid climate zone (4A, Virginia, USA). Circuit-level energy monitors were used to measure energy consumption and energy production data (solar photovoltaic) at 1-hr intervals in six identical apartments over 24 months. The study employs a multi-step case study methodology to a) empirically evaluate energy consumption and production data, b) identify the temporal variability of energy consumption and production data at different time scales, c) understand the impact(s) of weather and human-building interaction on energy consumption and production, and d) synthesize the study’s “lessons learned” toward data-driven recommendations for future NZEH researchers and practitioners. The study found that the development’s net zero energy goal was achieved in three of six case units and that NZEH housing performance was more influenced by human-building interaction than weather variability. The analysis also found the solar photovoltaic (PV) performance to be reliable across the sampled units over the periods of measurement, suggesting that solar PV could be oversized as an approach to overcome verifiability in HBI and achieve NZEH performance goals.

Desalinators are traditionally driven by fossil-fuels but in order to avoid greenhouse emissions, renewable energy must be used. In this paper, a coupling between multi-stage flash distillation apparatus and a parabolic trough solar collector is analyzed. The purpose of this study is to determine the economic feasibility of the system, considering four cities of Saudi Arabia and three different potable water productions. To avoid solar energy intermittency and unavailability at night, thermal storage is implemented. Whereas other researchers made parametric analyses, in this paper, the authors developed a mathematical program which was optimized with the help of GAMS software, where the capital cost of the plant was the objective function. After that, a life cycle cost analysis was carried out for each scenario. Depending on the region and water production, the costs of drinking water vary from 2.26 to 3.93 US$/m³, and from 7440 to 23825 tons of carbon dioxide emissions are avoided. As a consequence of the approach used, low costs are obtained; even though no auxiliary heater is implemented and the lowest irradiance conditions are considered. The results of this study reflect that the proposed process is competitive with respect to the traditional one.

Surface passivation, which has been intensively studied recently, is essential for the perovskite solar cells (PSCs), due to the intrinsic defects in perovskite crystal. A series of chemical or physical methods have been published for passivating the defects of perovskite, which effectively suppressed the charge recombination and enhanced the photovoltaic performance. In this study, the n-type semiconductor of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) is dissolved in chlorobenzene (CB) for the surface passivation during the spin-coating process for depositing the two-dimensional (2D) perovskite film. This approach simplifies the fabrication process of 2D PSCs and benefits the film quality. As a result, the defects of perovskite film are effectively passivated by this method. A better perovskite/PCBM heterojunction is generated, exhibiting an increased film coverage and improved film morphology of PCBM. It is found that this technology results in an improved electron transporting performance as well as suppressed charge recombination for electron transport layer. As a result, PSCs based on the one-step formed perovskite/PCBM heterojunctions exhibit the optimized power conversion efficiency of 15.69% which is about 37% higher than that of regular perovskite devices. The device environmental stability is also enhanced due to the quality-improved electron transport layer.

A typical white-light light-emitting diode (LED) can achieve a sunlight-like spectral profile in the visible spectrum by means of using an optical filter, with an inverted transmission profile to the white LED, fabricated using a deposition coating process. The unfiltered white LED generates white light by mixing light emitted by a blue LED (450 nm) with emission from the yellow phosphorescence excited by the blue light and differs significantly from the characteristics of the full-spectrum natural light. In this study, the spectral characteristics of the filtered LED light can be improved to reach a general color rendering index value (Ra) of 95.6 at the D65.

Particle layers employing conductive transition metal nitrides have been proposed as possible alternative plasmonic materials for photovoltaic applications due to their reduced losses compared to metal nanostructures. We critically compare the photocurrent gain due to an additional layer made of nanopillars of nitrides with other material classes obtained in an already highly optimized doped c-Si baseline solar cell with accurate doping profile from measurements. A relative photocurrent gain with respect to the baseline cell of on average 5% to 10% is observed, with a few cases achieving around 30% gain. While the local field enhancement is moderate resonances for nitrides spread over the whole UV-VIS range. For some nitrides, the shading effect remains a problem similar as for metals, but others behave more like dielectric scatterers with high photocurrent gain.

The residential sector in the United States is in need of comprehensive policy-making reforms that concurrently address housing affordability and environmental sustainability. This study investigates the feasibility of state-wide zero-energy affordable housing by analyzing historical data on climate, energy use, and solar system costs in the Commonwealth of Virginia. The hypothesis examined is that the net present cost of implementation of rooftop residential solar systems to achieve zero-energy Low-Income Housing Tax Credit (LIHTC) buildings is lower than the discounted present cost of energy of otherwise identical conventional buildings that run without renewable energy generation systems. The authors propose a generalizable framework for analyzing the feasibility of achieving region- or state-wide zero-energy LIHTC developments. To validate the framework, the authors employ a longitudinal sample of monthly energy use data from 2013-2016 obtained from 310 residential units of 15 LIHTC developments across the state. Based on statistical regression analysis, energy simulation, and simulation-based risk analysis, the authors find that the net present value of zero-energy LIHTC investments can be positive with a low risk. The investment value varies often depending on the zero-energy building definition, weather characteristics, retail price of electricity, and incentive rate. This study can help housing policymakers and industry professionals analyze and benchmark the feasibility of innovative zero-energy housing policies and projects.

A Life Cycle Analysis was performed considering three existing power plants of comparable size operating with different sources of renewable energy: geothermal, solar and wind. Primary data were used for building the life cycle inventories. The geothermal power plant includes emissions treatment for removal of hydrogen sulfide and mercury. The scenario about the substitution of natural emissions from geothermal energy, with specific reference to the greenhouse effect, is also investigated performing a sensitivity analysis. The results are characterized employing a wide portfolio of environmental indicators employing the Recipe 2016 and the ILCD 2011 Midpoint+ methods; normalization and weighting are also applied using the Recipe 2016 method at endpoint level. The results demonstrate a good eco-profile of geothermal power plant with respect to other renewable energy systems and allow for a critical analysis to support potential improvements of the environmental performances.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Photoelectrochemical systems have the potential to contribute to de-carbonation of the energy system because solar energy can be directly converted to hydrogen which can be burnt without the release of greenhouse gases. However, meaningful deployment of photoelectrochemical (PEC) technology in the global energy system, even when highly efficient scaled up devices become available, shall only be a reality when their safe and reliable operation can be guaranteed over serveral years of service life. The first part of the review discusses the importance of hermetic sealing of up scaled PEC device provided by the casing and sealing joints from a reliability and risk perspective. The second part of the review presents a survey of fully functional devices and early demonstrators and uses this to establish the extent to which the state of the art in PEC device design address the issue of hermetic sealing. The survey revealed that current material choices and sealing techniques are still unsuitable for scale –up and commercialization. Accordingly, we examined possible synergies with related photovoltaic and electrochemical devices that have been commericalised and derived therefrom, recommendations for future research routes that could accelerate the development of hermetic sealings of PEC devices.

The study carried out by simulation, concerns the thermal behavior of an office building’s solar fresh air cooling system, based on a LiBr-H₂O absorption chiller in different climatic conditions. The coefficient of performance (COP) and the solar fraction were considered performance parameters and were analyzed with respect to the operating limits: risk of crystallization and maintaining at least a minimum degassing zone. A new correlation between the required solar hot temperature and the cooling water temperature was established and then embedded in another new correlation between the COP and the cooling water temperature that was used in simulations during the whole cooling season corresponding to each location. It was found that: the solar hot water should be maintained in the range of (80-100) °C depending on the cooling water temperature, the COP of the solar LiBr-H₂O absorption chiller with or without cold storage tank can reach (76.5-82.4) % depending on the location, and the solar fraction can reach (29.5-62.0) % without cold storage tank and can exceed 100 % with cold storage tank, the excess cooling power being available to cover other types of cooling loads: through the building envelope, from lighting, from occupants, etc.

The moon always use the same side to face toward the earth, but there is a dead angle in the mainstream theory of explaining this phenomenon. That is, it cannot explain why the moon doesn't rotate around the axis which is a straight line to connect the mass centers of the earth and moon. Because the numerous meteorite impact craters on the lunar surface indicate that the moon is completely possible to obtain external momentums and rotate around this axis. This paper proposes a plain explanation, that is, the universal gravitation between the earth and moon as well as the earth's magnetic field have formed a trinity restraint mechanism on the moon. According to this explanation, the moon's rotation can be locked, and the mechanism of lunar libration has been revealed out, which can also confirm mutually with the natural phenomenon that the moon has sought a balance in the swing. In addition, with the help of all kinds of detection data from the Apollo moon landings and other circumlunar spacecraft, as well as the studies and analysis of lunar soil samples, the conclusion is that as far as a whole for the moon, it belongs to paramagnetic substances, and its relative permeability is between 1.008 and 1.03. Although the magnetic flux density of the earth on the lunar orbit has been dropped below 0.0008125 nT or lower due to the impact of the solar wind, but it can be used as a reason to lock the moon without rotating around the axis which is a straight line to connect the mass centers of the earth and moon. If another main reason to cause the existence of this fact cannot be found, even if the magnetic flux density of the geomagnetism in lunar orbit is very small, it also should not be artificially ignored. In this regard, we can artificially change the intensity of the earth's magnetic field, and carefully observe the lunar libration and in the distance between the earth and the moon, to verify the arguments in this paper.

InGaN/GaN samples grown on c-plane sapphire substrate with different In concentrations by metal organic chemical vapor deposition are demonstrated. The subsequent capping GaN layer growth opens a possibility for dislocation reduction due to the lateral strain relaxation in growth geometry. We present the further growth optimization and innovative characterization of InGaN layers overgrown on different structures with varying In concentrations. The photoelectrical and optical properties of the InGaN layers with or without capping GaN layer were investigated by time-resolved picosecond transient grating and temperature dependence photoluminescence. We note a 10-fold increase in carrier lifetime in the InGaN layers when the sample structure changes from PIN to single InGaN layer.

In this study an adjusting post-processing approach is implemented for improving intra-hourly forecasts of solar power and ramp events of PV solar power systems at different locations in the United States. This study also serves as an out-of-sample test to evaluate the performance of the adjusting approach with different locations and timescales. Thus, various individual intra-hourly forecasts of solar power are combined and adjusted by applying the adjusting approach. Both point and probabilistic forecasts of solar power are included. After that, solar power ramp event forecasting by the adjusting approach is carried out.

The Absorbing/scattering nature of aerosols affects the total radiative forcing and this absorption to total extinction ratio is quantified by single scattering albedo (SSA). Effect of SSA in the Ultraviolet (UV) irradiance is less studied and limited measurements are available. SSA retrieved at Athens, Greece during 2009-2014 from Ultraviolet Multifilter Radiometer (UVMFR) at 332 and 368 nm, were used to calculate incoming UV irradiance, alongside with ones from AERONET at visible wavelengths, from OMI satellite at 342.5 nm and from AEROCOM climatological database at 300 nm. UVA and UVB irradiances were estimated using a Radiative Transfer Model and we found that relative differences could be as high as 20%, while average relative differences varied from 2% to 8.7 % for the whole experimental period. Both UVA and UVB drop by a rate of ~12% for 0.05 aerosol absorption optical depth compared to ones estimated using SSA at visible range. Brewer irradiance measurements at 324nm were used to validate simulated irradiances and a better agreement was found when UVMFR SSAs were used with an average difference of 0.86%, while when using visible or climatological input, relative differences were estimated +4.91 and +4.15% accordingly.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

Solar concentrator photovoltaic collectors are able to deliver energy at higher temperatures for the same irradiances, since they are related to smaller areas for which heat losses occur. However, to ensure the system reliability, adequate collector geometry and appropriate choice of the materials used for all their components will be crucial. The present study focuses on the re-design of the C-PV collector reflector currently produced by the Swedish company Solarus AB, together with a comparative analysis based on the annual assessment of the solar irradiance in the collector. An open-source ray tracing code (Soltrace) is used to accomplish the modelling of optical systems in concentrating solar power applications. Symmetric parabolic reflector configurations are seen to improve the PV system performance when compared to the conventional structures currently used by Solarus. The parabolic geometries, using either symmetrically or asymmetrically placed receivers inside the collector, achieve both the performance and cost-effectiveness objectives: for almost the same area or costs, the new proposals for the PV system may be in some cases 70 % more effective as far as energy output is concerned.

A study of photovoltaic solar window technologies is reported, focusing on their structural features, functional materials, system development, and suitability for use in practical field applications, e.g. public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 W_p/m² from clear and transparent large-area glass-based solar windows.

A flow chart is presented depicting coupling in ocean-atmosphere system, initiated by solar decadal variability that involves El Niño Southern Oscillation (ENSO). Possible mechanisms for Canonic ENSO, Modoki ENSO and Canonic-Modoki ENSO are proposed considering their relevance to the decadal variation of Hadley, Walker circulation and mid-latitude jets. It also discusses subsequent teleconnections by ENSO on Indian Summer Monsoon (ISM) with a special emphasis on later two decades of the last century. Possible mechanisms relating to a disruption of the usual ENSO-ISM teleconnection for those decades are emphasised; the role of volcanos and the change in the sun- NAO (North Atlantic Oscillation) connection were attended. The regional Hadley circulation, via the NAO in the northern hemisphere and Indian Ocean Dipole in the southern hemisphere, during that period, may have a role in the change in ISM behaviour- which though captured in observation but missed by models. The representation of flow chart helps to improve understanding of various types of ENSO in both temporal as well as spatial scale. The overall study subsequently can benefit the modelling community by not only improved the representation of ENSO in models but also better representation of ISM teleconnection via regional Hadley cell.

Solar energy is derived from photons of light coming from the sun in a form called radiation. Solar energy finds extensive application in air and water heating, solar cooking, as well as electrical power generation, depending on the way of capturing, converting and distribution. To enable such application, it is necessary to analyze the horizontal tilt angle of horizontal surfaces – in order that when the solar energy reaches the earth surface to be completely absorbed. This paper tends to describe the availability of solar radiation for south-facing flat surfaces. The optimal monthly, seasonal, and annual tilt angles have been estimated for Pristina. The solar radiation received by the incident plane is estimated based on isotropic sky analysis models, namely Liu and Jordan model. The annual optimum tilt angle for Pristina was found to be 34.7°. The determination of annual solar energy gains is done by applying the optimal monthly, seasonal and annual tilt angles for an inclined surface compared to a horizontal surface. Monthly, seasonal and annual percentages of solar energy gains have been estimated to be 21.35%, 19.98%, and 14.43%. Losses of solar energy were estimated by 1.13 % when a surface was fixed at a seasonal optimum tilt angle, and when it was fixed at an annual optimum tilt angle, those losses were 5.7%.

We consider an alternative hypothesis of crater formation -- through an electric discharge machining (EDM) of the celestial bodies' surfaces. The source of the energy and the current itself may lie in the plasma infalling on a celestial body (from an extremely strong solar outburst or a nearby supernova). This mechanism may have been even more important than impact cratering in the early Solar System, with potential implications to the history of the dynamics of the System itself and solar activity in particular. In this light, the conclusion that shocked and metamorphosed minerals found within crater sites are evidence of hypervelocity impacts might be reconsidered. There are ambiguities that remain among sources of mineralogical formations. This study is ongoing with details of investigations supporting a new approach to crater formation not yet exhausted. Apart from mineralogical analysis and theoretical considerations regarding the large scale crater formation, we present a description of experimental studies of EDM acting at low pressures. Experimental results are made with crude setups and could easily be replicated on a larger scale with valuable research potential, as there is a well understood relation between the crater size and the energy needed for its production.

Keywords: Artificial Neural Network (ANN), Support Vector Machine (SVM), Support Vector Regression (SVR), Lightweight Gradient Boosting Machines (Light GBM), Machine Learning, Solar Irradiance (SI), Solar forecasting

The research develops and validates new decomposition models for DNI estimations from Southern African data. The results demonstrated improved DNI estimation accuracy compared to the baseline models across all testing and validation datasets. These outcomes suggest that utilising a localised model can significantly enhance DNI estimations for Southern Africa and potentially for developing similar models in diverse geographic regions worldwide. Furthermore, clustered models highlighted the potential advantages of grouping data based on shared geographical and climatic attributes. This clustering approach could enhance decomposition model performance, particularly when local data is limited or data is available from multiple nearby stations. The Southern African decomposition model, which encompasses a wide spectrum of climatic regions and geographic locations, exhibited notable improvements over the baseline models despite occasional overestimation or underestimation. The overall metrics affirm the substantial advancement achieved with the Southern African model. This study focused on validating the model for hourly DNI in Southern Africa within a range of clearness index-intervals from 0.175 to 0.875. Implementing accurate decomposition models in developing countries can accelerate the adoption of renewable energy sources, diminishing reliance on coal and fossil fuels.

Solar photovoltaic systems (PVs) are becoming more popular in Poland, as the country aims to increase its share of renewable energy sources and reduce its dependence on coal. According to the official data the total installed PV capacity in Poland reached 15.6 GW in September 2023 while at the end of 2020 it was 4.1 GW. This situation was caused by many factors, but mainly by government subsidy programs for households and rising electricity prices. A number of photovoltaic installations with a capacity of up to 50 kWp were carried out, although the installation should always be adapted to the needs of a given household. Estimating the yield of solar energy systems is crucial for that. It can be done by several methods, but always as initial step in modelling of solar energy systems weather data, especially solar irradiation is required. To get this data we can arrange the measurement from ground stations or use reanalysis models and satellite-derived datasets. There are several different datasets, both public and commercial, of solar irradiance data ready to use. This data provides insights into the average solar irradiance levels throughout the year, aiding in estimating the energy generation capacity. The paper contributes the knowledge of energy generation capacity that can be quickly counted for a solar PV micro-system with different orientation and inclination as a multiplier of the energy value obtained from a solar PV system of 1 kW-peak for a significant number of locations in Poland based on open-source solar irradiation data

Since the energy sector is the main source of greenhouse gases, it has the highest potential for improvement. Improvements can be achieved by generating energy from renewable sources. Combined with thermal energy storage, concentrating solar power plants represent a promising technology for dispatchable renewable energy, ensuring a stable energy supply even in remote areas without contributing to greenhouse gas emissions during operation. However, it is important to note that greenhouse gases and other polluting emissions may occur during the manufacturing process of concentrating solar power plant components. This work analyses the design of the receiver to produce thermal energy for the existing solar dish CSP plant at the Energy Center of the Politecnico di Torino. The objective of this plant is to produce hot water for a small case study. Considering the average solar irradiance for Turin equal to 800 W/m2, the surface heat flux was obtained from the first part of the analysis, which was used to obtain the maximum internal temperature in the receiver equal to 873.7 °C. The maximum temperature obtained was a constraint for the selection of the material for the solar receiver. Of the various possibilities, copper was chosen. In the second part of the work, a Life Cycle Assessment was carried out to compare the emissions generated during the production of the main components of the CSP plant with the emissions generated by the methane-fuelled water heater that produces the same amount of water as the CSP plant. It can be concluded that the manufacture of the main components of the CSP plant results in lower greenhouse gas emissions than the operational phase of a conventional natural gas-fired water heater (1.6 kg CO2/day).

The power system has rapidly grown and expanded over the past decades and has been experiencing major changes and challenges. The increase in energy demand and the modern advancements in the smart grid, such as solar and wind energies and electric vehicles, have led to complexity and complications for utilities. A further layer of complexity and difficulty was added by the rapid expansion of behind-the-meter (BTM) photovoltaic (PV) systems with various designs and characteristic features. The rapid increase and the invisible solar power (BTM) have led to fluctuations in power grid stability and reliability and to inefficiency. Accurate forecasting of load generation will help to assure optimal planning, minimize the negative effects of the PV systems, and minimize the operational and maintenance costs. The authors propose a solution that uses combinations of K-means clustering with neural network machine learning models, AMI real-world PV load generation, and weather data to forecast the generation load at customer locations to achieve a 2.49% error between actual and predicted generation load.

As part of the Earth Climate Observatory space mission concept for the direct observation from space of the Earth Energy Imbalance, we propose an advanced camera suite for the high resolution observation of the Total Outgoing Radiation of the Earth. For the observation of the Reflected Solar Radiation, we propose the use of two multispectral cameras covering the range from 400 to 950 nm, with a nadir resolution of 1.7 km, combined with a high resolution RGB camera, with a nadir resolution of 0.57 km. For the observation of the Outgoing Longwave Radiation, we propose the use of 6 microbolometer cameras, with each a spectral bandwidth of 1 μm in the range from 8 to 14 μm, and with a nadir resolution of 2.2 km.

Evaluating of long-term satellite-derived ocean color products using in-situ measurements is essential to ensure data quality and integrity. In this study, the Visible Infrared Imaging Radiometer Suite (VIIRS) remote sensing reflectance (Rrs) products were evaluated and analyzed by using long-term OC-CCI in-situ data from 2012 to 2021. The results demonstrate that the root mean square difference of VIIRS Rrs product accuracy in most bands is better than 0.002 (sr-1) when considering its average life span of 12 years. However, the VIIRS Rrs products in shorter wavelength bands (e.g., at 412 nm) had significantly lower accuracy in general and a long-term bias over the recent years. The annual precision of VIIRS Rrs products showed a declining trend especially in coastal or eutrophic waters. This accuracy deterioration of the VIIRS Rrs products suggests a strong need for continuous monitoring of its performance and further efforts on improving the atmospheric correction algorithm to specifically deal with satellite records at high SZAs and OZAs.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

Solar energy is a renewable and sustainable source of energy, and it has been used in addition of specified technologies, such as solar cooling. The demand for cooling continues to increase in line with environmental changes and a greater desire for human comfort. This study primarily aimed to analyze the performance of an evaporative cooling system powered by solar energy and assess the economic and environmental impact of this system. In this system, hot, dry incoming air is used to evaporate water, thus transforming part of its sensitive heat into latent heat without any variation in enthalpy or total heat. The outputted air then has a lower temperature and a greater humidity, thus providing a more comfortable, healthier environment for its users. To achieve this study’s objectives, numerical code was developed and implemented in MATLAB. The obtained results reveal that the efficiency of the evaporative cooler exceeds 90%, with maximum efficiency being reached at a high wet-bulb depression, while minimum efficiency was observed when the dry air has a high relative humidity and a low dry-bulb temperature.

Research on the lead halide-based perovskite solar cells have obtained considerable interest in photovoltaic industry owing to their higher efficiency, easy manufacturing, light-weight and low cost. However, these lead halide-based solar cells are not suitable to manufacture commercially because of the toxicity of lead-based materials. In this context, a lead-free perovskite, cesium-bismuth iodide (Cs₃Bi₂I₉) is considered as a potential alternative to the lead halide-based cell due to their non-toxicity and stability, but this perovskite cannot be matched with random hole transport layer (HTL) and electron transport layer (ETL) materials compared to lead halide-based perovskite because of their crystal structure and band gap. Therefore, in this study, performance comparison of different ideal HTL and ETL materials for Cs₃Bi₂I₉ perovskite layer were studied using SCAPS-1D device simulation on the basis of open circuit voltage, short circuit current, power conversion efficiency (PCE) and fill factor (FF) as well as several novel PSC configuration model were designed that can direct for further experimental research for PSC device commercialization. Results from this investigation reveals that the maximum efficiency of 20.96% is obtained for the configuration ITO/WS₂/Cs₃Bi₂I_9­/NiO/Au with optimized parameters such as thickness 400 nm, band gap 2.1eV, absorber layer defect density 10¹² cm^-3, donor density of ETL 10¹⁸ cm^-3 and the acceptor density of HTL 10²⁰ cm^-3.

The aim of the study was to find the effect of polyethylene (PE) coatings on the short-circuit current of silicon photovoltaic cells covered with glass, in order to improve the short-circuit current of the cells. Various combinations of PE films (thicknesses ranging from 9 to 23 µm, number of layers ranging from 2 to 6) with glasses (greenhouse, float, optiwhite and acrylic glass) were investigated. The best current gain of 4.05% was achieved for the coating combining a 1.5 mm-thick acrylic glass with 2 × 12 µm-thick PE films. This effect can be related to the formation of an array of micro-wrinkles and micrometer-sized air bubbles with a diameter of 50 to 600 µm in the films, which serve as micro-lenses and enhance light trapping.

The term ‘biodynamic’ lighting is proposed as a term to capture the true aspiration of ‘life-centric’ lighting: good human and non-human outcomes for all life-sustaining behaviours on earth driven by good design for phototropism, phototaxis, photoperiodism and circadian entrainment. While future studies are necessary to consolidate this aspiration, it is clear that lighting has immediate potential to better support planetary health. As many aspects of animal, human and plantbehaviour and survival are being perturbed by widespread exposure to artificial light at night (ALAN), lighting professionals are in the middle, attempting to make design decisions that directly affect these life forms. This paper empowers readers with fundamental understandings of how light information is used by these life forms in a way crucial for development, growth and survival. The paper then provides a process for life-centric lighting design by drawing inspiration from an existing process for human-centric lighting design which can dovetail with decision-making processes that are within the workflow of lighting professionals. Holistic consideration of life-centric lighting design should look beyond altruism and romanticism by firmly rooting itself into pragmatism about long-term considerations for planetary health. Key references are consolidated and synthesized with goals of supporting knowledge translation into pragmatic lighting strategies in a manner useful for lighting professionals. While the scientific community remains sceptical about the term ‘biodynamic’ – which is argued to be developed through mysticism instead of scientific methodology – this paper counter argues that with appropriate use, the term has the potential to comprehensively capture this aspiration.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

This article has been developed to assess the economic feasibility of a roof-top photovoltaic installation of industrial self-consumption. Numerical models that enable an interested person to obtain the main expected parameters will be generated. To do this, a calculation methodology will be generated through which the reader, knowing the location of the facility and dimensions of the roof, will be able to calculate the maximum installable power, the main parameters related to production, the cost of the installation, and the LCOE of the plant. The use of actual costs will be facilitated in case they are known, but it will remain possible to apply the costs of the major equipment (modules, inverter, and structure) considered throughout the article. This developed calculation methodology will also allow a quick comparison of the forecasts of production, CAPEX, and LCOE of plants designed with different inclinations and different types of modules. Consequently, it will be especially useful for decision-making before developing the plant's basic engineering. Moreover, the calculations used for modeling the LCOE will be analyzed in depth. This analysis will allow evaluating how the different technical variables affect the profitability of a photovoltaic installation, such as the selected tilt, the location, the module's technology, or the available area.

The use of vitamin D (VitD) supplements has become widespread in the last decade due not only to the dissociation between the blood levels recommended as "optimal" and those shown by the healthy population, but also to its presumed beneficial effects on multiple disorders. This work evaluated the levels of 25-hydroxyvitamin D [25(OH)D] in a healthy population of European origin living in a region with high solar irradiation. In serum samples from a population-based study conducted in the Canary Islands, levels of 25(OH)D were analyzed. In 876 individuals who had no history of kidney or malabsorption disorders and who had not been treated with calcium and/or VitD supplementation, the median 25(OH)D level was 26.3 (5th;95th percentile, 14.3;45.8)ng/mL. Notably, 65.4% of the population had 25(OH)D blood levels below 30ng/mL, 23.4% below 20ng/mL and 6.4% below 15ng/mL. Based on the lack of evidence supporting causality between 25(OH)D levels below what is recommended as optimal (≥20ng/mL, or even ≥30ng/mL) and major skeletal and non-skeletal diseases, and in light of the distribution of the concentration of this vitamin in healthy adults living under optimal conditions of solar irradiation, it seems reasonable to consider 25(OH)D levels below 20ng/mL and close to 15ng/mL as adequate for the general population.

In this work, an evaluation and quantification of the impact of using mixtures based on Supercritical Carbon Dioxide "s-CO2" (s-CO2/COS, s-CO2/H2S, s-CO2/NH3, s-CO2/SO2) are made as a working fluid in simple and complex recompression Brayton s-CO2 power cycles configurations that have pressure drops in their components. These cycles are coupled to a solar thermal plant with parabolic-trough collector (PTC) technology. The methodology used in the calculation performance is to establish values of the heat recuperator total conductance (UAtotal) between 5 and 25 MW/K. The main conclusion of this work is that the cycle's efficiency has improved due to s-CO2 mixtures as working fluid; this is significant compared to that obtained using the standard fluid (pure s-CO2). Furthermore, a techno-economic analysis is carried out that compares each configuration's costs using pure s-CO2 and a mixture of s-CO2/COS with a molar fraction (70/30) respectively as working fluid where relevant results are obtained. These results show that the best configuration in terms of thermal efficiency and cost is the RCC-RH for pure sCO2 with values ​​of 41.25% and 2811 $/kWe, while for the mixture sCO2/COS, the RCC-2RH configuration with values ​​of 45, 05% and 2621 $/kWe is optimal. Using the mixture costs 6.75% less than if it is used the standard fluid (s-CO2).

This paper presents a detailed description of three methodologies to electrify the rural households of small loads with reliable and economical method using solar energy as input source of power. It is observed that high DC voltage is better and economical solution rather than AC based solar systems and low voltage DC systems. In this paper, three methodologies were analysed to select the right combination of portable converters with low prices, which may further enhance the energy access and affordability to common people. The proposed three methodologies were tested through action research in collaboration with a team of scientists and technical experts of National Institute of Solar Energy. The comparative analysis is carried out on three different converters, various kind of house loads and types of power supply i.e. AC/DC. The performance, quality and economic evaluation has been carried out with the help of MATLAB SIMULINK and other measuring instruments specific for solar photovoltaic systems. The derived results were analysed and inferences made for use in village household loads and their income groups. Further, a three-step analytical framework on village-level power energy efficient power at affordable power preposition was presented. This study will help in the designing as well as in the performance and economic evaluation of converters based on solar photovoltaic systems of different technologies.

This paper investigates the improvement in solar energy collection and conversion using Al₂O₃-Water nanofluids in a solar flat plate collector (SFPC). The efficiency of a solar flat plate collector using water as the fluid medium is analyzed experimentally and theoretically. For theoretical analysis, a mathematical model in MATLAB is used to simulate and is validated by the experimental results. To enhance the solar energy collection and conversion efficiency of the SFPC, Al₂O₃-Water nanofluid was selected as the fluid medium. The nanofluid properties like density, specific heat capacity, thermal conductivity and viscosity are analyzed and compared for several models of Al₂O₃-Water nanofluids and the best model was selected to modify the simulation. Effect of particle diameter in the nanofluid was found to be marginal on the nanofluid properties. The optimum volume concentration of the nanofluid was found to be 4% giving an efficiency increase of 7.78% in the SFPC over the use of water. This reduces the area of the SFPC by 10.5%.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

As the first initiative of its kind in Algeria, here is presented a solar-powered mobile “Ultraviolet Germicidal Irradiation” disinfection unit (UVGI) based on a special germicidal ultraviolet-C (UVC) radiator. The system was designed to disinfect several objects such as: medical tools, reusable masks, face-shields, gloves, phones, laptops, keys, money and many other portable devices that need to be disinfected/sterilized. It offers the advantage of complete autonomy through the built-in photovoltaic (PV) system that includes a solar panel, a gel battery, a charge controller and a power inverter. The system provides an extra 220V-50Hz outlet with 375VA maximum power to be used when energy is needed. The system is easily scalable to generate higher ultraviolet dosages by adding more UVC lamps. The chemical-free germicidal UVC sanitizing method employed by this device effectively disactivates a very wide range of microorganisms (microbes, bacteria and fungi and viruses including the actual SARS-CoV-2 that causes COVID-19 respiratory disease) and it has several advantages in comparison to chemical-based sanitizing methods. The total cost to make this open source device is below 1000 € and is easily customizable and scalable. This device is an open source, secure and fast equipment for objects and surface disinfection. The device will be fully automated by adding PIR sensors or remote control after further funding will be received.

Several studies have shown that changes in incoming solar radiation and variations of the diffuse fraction can significantly modify the vegetation carbon uptake. Hence, monitoring the incoming solar radiation at large scale and with high temporal frequency is crucial for this reason along with many others. The EUMETSAT Satellite Application Facility for Land Surface Analysis (LSA SAF) operationally disseminates in near real time estimates of the downwelling shortwave radiation at the surface since 2005. This product is derived from observations provided by the SEVIRI instrument onboard the Meteosat Second Generation series of geostationary satellites, which covers Europe, Africa, the Middle East, and part of South America. However, near real time generation of the diffuse fraction at the surface level has only recently been initiated. The main difficulty towards achieving this goal was the general lack of accurate information on the aerosol particles in the atmosphere. This limitation is nowadays less important thanks to the improvements in atmospheric numerical models. This study presents an upgrade of the LSA-SAF operational retrieval method, which provides the simultaneous estimation of the incoming solar radiation and its diffuse fraction from satellite every 15 minutes. The upgrade includes a comprehensive representation of the influence of aerosols based on physical approximations of the radiative transfer within an atmosphere-surface associated medium. This article explains the retrieval method, discusses its limitations and differences with the previous method, and details the characteristics of the output products. A companion article will focus on the evaluation of the products against independent measurements of solar radiation. Finally, the access to the source code is provided through an open access platform in order to share with the community the expertise on the satellite retrieval of this variable.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

Chinese investors are easily affected by hot topics on the media and Internet and likely take irrational behavior. They tend to consume rationally and invest emotionally. This research aims to analyze the Baidu index’s effect on share price of solar power industry in China. Three main models are established to identify the correlation between Baidu index and stock price of solar industry. The media index and searching index of Baidu are chosen as an independent variable to measure the influence from media and Internet, and stock price as the dependent variable. To improve and complete the analysis, Hexun index is taken into consideration as mediator variable. This study applied Multiple Linear Regression Model and VAR (Vector auto-regression) Model. The research mainly uses the tools of SPSS, Eviews and Excel to conduct data analysis. The test is based on the theories of Granger Causality, unit root test, F-test, and t-test. The research proves the relationship between the close price of stock and Baidu index, and it also created a model for further forecasting.

Quality control (QC) may be a lengthy and tedious process. As a result, most data users use data from meteorological services without performing data quality checks. The South African Weather Service (SAWS) re-established the national solar radiometric network comprising of 13 new stations within the six climatic zones of the country. This study reports on the performance results of the Baseline Surface Radiation Network (BSRN) QC procedures applied to the solar radiation data within the SAWS radiometric network. The overall percentage performance of the SAWS solar radiation network based on BSRN QC methodology is 97.79%, 93.64%, 91.6% and 92.23% for Long Wave Downward Irradiance (LWD), Global Horizontal Irradiance (GHI), Diffuse Horizontal Irradiance (DHI) and Direct Normal Irradiance (DNI) respectively with operational problems largely dominating the percentage of bad data. The overall average performance of the Surface Solar Radiation Dataset – Heliosat (SARAH) data records for the GHI estimation for all the stations showed a Mean Bias Deviation (MBD) of -8.28 Wm^-2, a Mean Absolute Deviation (MAD) of 9.06 Wm^-2 and the Root Mean Square Deviation (RMSD) of 11.02 Wm^-2. The correlation (quantified by R²) between ground-based and SARAH-derived GHI time series was ~ 0.98. The established network has the potential of providing high quality minute solar radiation data sets (GHI, DHI, DNI and LWD) and auxiliary hourly meteorological parameters vital for scientific and practical applications in renewable energy technologies in South Africa.

Compound parabolic concentrators are relevant systems used in solar thermal technology. With adequate tailoring, they can be used as an efficient and low-cost alternative in residential water applications. This work presents a simulation study using a ray tracing methodology. With this technique we simulate the interaction between solar rays and solar concentrator to quantify the amount of energy that impinges on the receiver at a particular time. Energy availability is evaluated in a comparison of two configurations: stationary at 21° throughout the year and multi position setup; tilted with respect to the horizontal depending on three seasonal positions: 0° for summer, 16° for spring / autumn and 32° for winter, with the objective of increasing the amount of available energy in each season. The fact that a tracking system can be dispensed with also represents an economical option for the proposed application. The results showed that at 21°, the proposed system works satisfactorily; however, by carrying out the selected angular adjustments, the overall energy availability increased by 22%, resulting in a more efficient option. The methodology developed herein proved to be a valuable tool for prototype design and performance evaluation.

Investments in wind and solar power are driven by the aim to maximize the utilization of renewable energy (RE). This results in an increased concentration of wind farms at locations with higher average wind speeds and of solar panel installations at sites with higher average solar insolation. This is unfavourable for energy suppliers and for the overall economy when large power output fluctuations occur. Thus, when evaluating investment options for spatially distributed RE systems, it is necessary to model resource fluctuations and power output correlations between locations. In this paper, we propose a methodology for analyzing the spatial dependence, accurate modeling, and forecasting of wind power systems with special consideration to spatial dispersion of installation sites. We combine vine-copulas with the Kumaraswamy distribution to improve accuracy in forecasting wind power from spatially dispersed wind turbines and to model solar power generated at each location. We then integrate these methods to formulate an optimization model for allocating wind turbines and solar panels spatially, with an end goal of maximizing overall power generation while minimizing the variability in power output. A case study of wind and solar power systems in Central Ontario, Canada is also presented.

The technologies influencing alternative ways of transportation are augmenting in recent years as the need for transportation is increasing rapidly due to urbanization and motorization. In this paper, a solar powered electric auto-rickshaw (SPEA) is designed and developed for Indian conditions. The developed vehicle is comprehensively analyzed techno-economically for its viability in the Indian market. The performance analysis of SPEA results in an optimal charging rate of 2 kWh per day with an average solar irradiance of 325 W/m2. The discharging characteristics are studied based on different loading conditions. The vehicle achieved a maximum speed of 21.69 km/h with battery discharge rate of 296W at 90kg load and also reached a maximum discharge rate of 540W at 390kg loading with a maximum speed of 12.11 km/h. The environmental analysis of SPEA displayed yearly CO2 emissions of 1,777 kg, 1,987 kg and 1,938 kg using Compressed Natural Gas, Liquefied Petroleum Gas and gasoline engines respectively can be mitigated using SPEA. The results of financial analysis of SPEA were welcoming as the investor gets 24.44% lesser payback duration compared to gasoline run vehicle. Socio-Economic analysis of SPEA discussed its significant advantages and showed 18.73% and 3.9% increase in yearly income over gasoline driven and battery driven vehicles.

Solar energetic particles (SEPs) are bursts of high-energy particles that originate from the Sun and can last for hours or even days. The aim of this study is to understand how the characteristics of energetic particles was affected by the characteristic parameters of corotating interaction regions (CIRs). In particular, the particle intensity distribution with time and space in different CIRs are studied. The propagation and acceleration of particles are described by the focused transport equation (FTE). We used a three-dimensional magnetohydrodynamic (MHD) model to simulate the background field including CIRs. By changing the inner boundary conditions, we constructed CIRs with different solar wind speeds, angles between the polar axis and rotation axis, and the azimuthal widths of the fast streams. Impulsive particles are injected at the inner boundary. We then study the SEPs in different backgrounds. The results show that the CIR widths are related to the solar wind speed, tilt angles, and the azimuthal widths of the fast stream. The acceleration of particles in the reverse and forward compression regions is mainly influenced by the solar wind speed difference and the slow solar wind speed, respectively. Particles with lower energy (sub-MeV) are more sensitive to the parameters of CIRs. Different CIR parameters also greatly affect the spatio-temporal distribution of particle intensities in different ways. These results indicate that, it is crucial to consider the conditions of large-scale structure in interplanetary space when studying or predicting energetic particles. Additionally, our findings provide empirical guidance for forecasting the characteristics of SEPs.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

In the context of the French tertiary decree, it is crucial to reduce the energy consumption of buildings by first addressing the design of the electrical architecture. Implementing Direct Current (DC) nanogrids in buildings could offers a promising advantage for energy efficiency, significantly impacting overall energy consumption and sustainability goals. For an insulated area with a subtropical climate, such as La Réunion island, DC nanogrids could also facilitate the insertion of local renewable energy sources, especially solar energy. This article presents the deployment and efficiency evaluation of an end-to-end Low Voltage Direct Current (LVDC) nanogrid, from conception to real-world installation within a company. The nanogrid consists of a photovoltaic power plant, a Lithium-Iron-Phosphate (LFP) battery, and DC end-use equipment such as LED lighting and DC fans for two individual offices. An innovation is provided for the power supply and energy management of terminal equipment using the Power Over Ethernet (PoE) standard IEEE 802.3bt. The efficiency of the nanogrid is measured to be 40% higher than the efficiency of an installation powered by PV and distributed at 230 VAC. These results are obtained under certain deployment conditions, which are discussed in this article, in order to enhance the energy efficiency of buildings by using 48VDC. The nanogrid hardware and software infrastructure, the methodology employed for efficiency quantification and the measurement results are described in the paper.

This paper aims to study the performance of solar collectors with various sizes under different weather conditions of different Japanese cities, i.e. Kofu city, Nagoya city and Yamagata city. The heat generated from the solar collector was used to conduct a biogas dry reforming reactor in order to produce H2 to feed a solid oxide fuel cell (SOFC). This study has revealed that the output temperature of solar collector, Tfb in April and July was higher than that in January and October irrespective of city. The optimum length of absorber (dx) of the collector was 4 m irrespective of city. It was clarified that Tfb in Yamagata city in January and October, i.e. winter and autumn is lower than that in Kofu city and Nagoya city especially, which is influenced by the tendency of a solar intensity (I) strongly, not velocity of surrounding air (ua). On the other hand, Tfb is almost the same in April and July, i.e. spring and summer, irrespective of city. The amount of produced H2 from the biogas dry reforming reactor and the power generated by SOFC using H2 in spring and summer were higher compared to the other seasons irrespective of city. This study has revealed that the highest available households number per month was 4.7 according to the investigation in this study.

We consider the restrictions on photovoltaic (PV) capacity that are caused by limitations on where panels can be sited, and find quantitative evidence for the need for high efficiencies. We define 15% of the UK’s energy consumption as a “significant” contribution and, with London as an exemplar, we perform an idealised calculation that makes the most optimistic possible assumptions about the capabilities of future PV technologies, and use published surveys of energy usage, dwelling type and insolation. We find that covering every UK domestic roof with the highest power-conversion efficiency (PCE) solar panels currently commercially available, could produce up to 9% of the UK's energy. A 15% contribution would require PV technologies with >37% PCE, more than the theoretical Shockley-Queisser limit. Replacing the idealising assumptions with more realistic estimates increases this by 2-3 times. Alternatively, a solar farm using the currently available PCEs would require a politically challenging ~1200km2 of new land, roughly the area of Greater London, for this 15% contribution. We conclude that PCEs must be driven higher even than the Shockley-Queisser limit for PV to play a significant part in carbon mitigation.

In this work, the optoelectronic characteristics of kesterites of the Cu₂NiXS₄ system (X = Si, Ge, Sn) were studied. The electronic properties of the Cu₂NiXS₄ (X = Si, Ge, Sn) system were studied using first-principles calculations within the framework of density functional theory. For calculations, ab initio codes VASP and Wien2k were used. The high-precision modified Beke-Jones (mBJ) functional and the hybrid HSE06 functional were used to estimate the bandgap, electronic and optical properties. Calculations have shown that when replacing Si with Ge and Sn, the band gap decreases from 2.58 eV to 1.33 eV. Replacing Si with Ge and Sn reduces the overall density of electronic states. In addition, new deep (shallow) states are formed in the band gap of these crystals, which is confirmed by the behavior of their optical properties. The obtained band gap values are compared with existing experimental measurements, demonstrating good agreement between HSE06 calculations and experimental data. The nature of changes in the dielectric constant, absorption capacity and optical conductivity of these systems depending on the photon energy has also been studied. The statistical dielectric constant and refractive index of these materials were found. The results will help increase the amount of information about the properties of the materials under study and will allow the use of these compounds in a wider range of optoelectronic devices, in particular, in solar cells and other devices that use solar radiation to generate electric current.

This work investigates the influence of ground albedo on the solar radiation obtained by surfaces mounted on fixed-tilt to south, one-axis, and two-axis systems. To do this, estimation of the solar radiation difference is performed by applying real albedo and zero albedo. This is done within Saudi Arabia, at 82 selected sites. Annual, seasonal, and monthly mean solar energy differences are computed as function of the site’s number, latitude, and local near-real ground albedo. The great variation in the ground-albedo values at the 82 sites (0.1 - 0.46) could be thought as having a significant effect on the solar radiation levels received on the 3 tracking modes. The analysis shows quite the opposite; a zero-albedo ground diminishes solar radiation levels by 1.43%, 3.50%, and 3.20%, respectively for the 3 modes. Therefore, in most solar engineering applications a ground albedo of 0.2 (considered as reference) can be used without losing accuracy. This is the main conclusion of the study, which must, however, be applied with caution in areas with snow cover, especially for mode-III tracking systems. In such situations the increase in solar radiation levels may be up to 15% (but ≈3.5% for mode-I and -II systems instead).

Solar geoengineering (SG) solutions have many advantages compared to the difficulty of carbon removal (CR): SG produces fast results, is shown here to have much higher efficiency than CR, is not related to fossil fuel legislation, and is something we all can participate in brightening the Earth with cool roofs, and roads. SG requirements detailed previously to mitigate global warming (GW) have been concerning primarily because of overwhelming goals and climate circulation issues. In this paper, the advantages of annual solar geoengineering (ASG) to mitigate yearly global warming increases are explored and detailed as it provides higher feasibility in geoengineering applications. ASG area modification requirements found here are generally 50 to possibly higher than 150 times less compared to the challenge of full SG GW mitigation reducing circulation concerns. Results indicate that there are mixed technologies that can help meet annual mitigation Earth brightening goals. As well, results show much higher feasibility for L1 space shading compared to prior literature estimates for full GW mitigation. However, stratosphere injections appear challenging in the annual approach. Because ASG earth brightening area requirements are much smaller than those required for full mitigation, we have concerns that worldwide negative SG would interfere with making positive advances for several reasons. Negative SG currently dominates yearly practices with the application of dark asphalt roads and roofs. This issue is discussed.

Two gallium porphyrins, a tetraphenyl GaCl porphyrin, termed as (TPP)GaCl, and an octaethylporphyrin GaCl porphyrin, termed as (OEP)GaCl were synthesized to use as electron cascade in ternary organic bulk heterojunction films. A perfect matching of both gallium porphyrins energy levels with that of poly(3-hexylthiophene-2,5-diyl) (P3HT) or poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) polymer donor and the 6,6-phenyl C71 butyric acid methyl ester (PCBM) fullerene acceptor forming an efficient cascade system that could facilitate electron transfer between donor and acceptor was demonstrated. Therefore, ternary organic solar cells (OSCs) using the two porphyrins in various concentration were fabricated, where a performance enhancement was obtained. In particular, (TPP)GaCl-based ternary OSCs of low concentration (1:0.05 vv%) exhibited a ~17 % increase of the power conversion efficiency (PCE) compared with the binary device due to improved exciton dissociation, electron transport and reduced recombination. On the other hand, ternary OSCs with the (TPP)GaCl of high concentration (1:0.1 vv%) and (OEP)GaCl (1:0.05 and 1:0.1 vv%) showed poorest efficiencies due to very rough nanomorphology and suppressed crystallinity of ternary films when the GaCl porphyrin introduced in the blend, as revealed from X-ray diffraction (XRD) and atomic force microscopy (AFM). The best performed devices exhibited also improved photostability, when exposed to sunlight illumination for a period of 8 h than the binary OSCs, attributed to the suppressed photodegradation of the ternary (TPP)GaCl 1:0.05-based photoactive film.

The present study describes the development and application of a computer model of the national electricity system for the Caribbean dual-island nation of Antigua and Barbuda to investigate the cost-optimal mix of solar photovoltaics (PV), wind, and in the most novel contribution, concentrating solar power (CSP). These technologies, together with battery and hydrogen energy storage, can enable the aim of achieving 100% renewable electricity and zero carbon emissions. The motivation for this study was that while most nations in the Caribbean rely largely on diesel fuel or heavy fuel oil for grid electricity generation, many countries have renewable resources beyond wind and solar energy. Antigua and Barbuda generates 93% of its electricity from diesel-fueled generators and has set targets of becoming a net-zero nation by 2040 and having 86% renewable energy generation in the electricity sector by 2030, but the nation has no hydroelectric or geothermal resources. The modeled, optimal mix of renewable energy technologies presented here was found for Antigua and Barbuda by assessing the levelized cost of electricity (LCOE) for systems comprising various combinations of energy technologies and storage. Other factors were also considered, such as land use and job creation. It was found that 100% renewable electricity systems are viable and significantly less costly than current power systems, and that there is no single defined pathway towards a 100% renewable energy grid, but several options are available.

We investigate the performance of a novel flat photovoltaic-thermal (PV-T) module under high-vacuum through a 1D numerical model based on steady-state energy balance, with the aims of optimizing the simultaneous production of thermal and electrical energy. In the proposed design, the photovoltaic (PV) cell is positioned directly above the selective solar absorber (SSA), in a multilayer or fully integrated PV-SSA structure, which allows full exploitation of spectral solar radiation. In fact, in this configuration the losses related to non-absorption of low-energy photons and thermalization, typical of a classical single-junction PV cell, are reduced. The present study is conducted as the emittance and energy bandgap of the PV layer varied, thus admitting a wide variety of materials into the analysis. The dependence of the temperature coefficient, β(%/K), on the energy bandgap of the PV cell is also included. In the last part of the work, we discuss the performance of the proposed evacuated PV-T equipped with a SSA layer and thin film solar cells, namely those made of CdTe, CdS and GaAs. Overall, the paper highlights the great advantage of using high vacuum insulation, which suppresses conductive losses, and the versatility of the proposed system, which could be adapted to the user's needs simply by choosing the appropriate material for the photovoltaic layer.

Artificial roughness applied to the Solar Air Heater (SAH)’s absorber plate is a popular technique to increase its total-thermal efficiency (η_(t-th)). In this paper, the influence of geometrical parameters of V-down ribs attached below the corrugated absorbing plate of SAH on the η_(t-th) has been examined. The impacts of key roughness parameters, including relative pitch p⁄e (6-12), relative height e⁄D (0.019-0.043), angle of attack α (30°-75°), and Re (1000-20000), are examined under real weather conditions. The SAH η_(t-th) roughened by V-down ribs is predicted using an in-house developed conjugate heat transfer numerical model. It has been shown that the maximum SAH η_(t-th) is 78.8%, predicted under steady-state conditions of Re = 20000, solar irradiance G =1000 W/m2, p/e = 8, e/D = 0.043, and angle =60. That is 15.7% more efficient than that of the default smooth surface. Under real weather condition, the η_(t-th) of the roughened SAH with single and double glass covers are 17.7% and 20.1%, respectively, higher than those of smooth SAH.

A partial aperture onboard calibration method can solve the onboard calibration problems of some large aperture remote sensors, which is of great significance for the development trend of increasingly large apertures in optical remote sensors. In this paper, the solar diffuser reflectance degradation monitor (SDRDM) in the onboard calibration assembly (CA) of the FengYun-4 (FY-4) advanced geostationary radiance imager (AGRI) is used as the reference radiometer for measuring the partial aperture factor (PAF) for the AGRI onboard calibration. First, the linear response count variation relationship between the two is established under the same radiance source input. Then, according to the known bidirectional reflection distribution function (BRDF) of the solar diffuser (SD) in the CA, the relative reflectance ratio coefficient between the AGRI observation direction and the SDRDM observation direction is calculated. On this basis, the response count value of the AGRI and the SDRDM is used to realize the high-precision measurement of the PAF of the AGRI B1 ~ B3 bands by simulating the AGRI onboard calibration measurement under the illumination of a solar simulator in the laboratory. According to the determination process of the relevant parameters of the PAF, the measurement uncertainty of the PAF is analyzed; this uncertainty is better than 2.04% and provides an important reference for the evaluation of the onboard absolute radiometric calibration uncertainty after launch.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

Solar3D is an open-source software application designed to interactively calculate solar irradiation at three-dimensional (3D) surfaces in a virtual environment constructed with combinations of 3D city models, digital elevation models (DEMs), digital surface models (DSMs) and feature layers. The GRASS GIS r.sun solar radiation model computes solar irradiation based on two-dimensional (2D) raster maps for given day, latitude, surface and atmospheric conditions. With the increasing availability of 3D city models and demand for solar energy, there is an urgent need for better tools to computes solar radiation directly with 3D city models. Solar3D extends GRASS GIS r.sun from 2D to 3D by feeding the model with input, including surface slope, aspect and time-resolved shading, that is derived directly from the 3D scene using computer graphics techniques. To summarize, Solar3D offers several new features which, as a whole, distinguish itself from existing 3D solar irradiation tools: (1) the ability to consume massive heterogeneous 3D city models, including massive 3D city models such as oblique airborne photogrammetry-based 3D city models (OAP3Ds or integrated meshes); (2) the ability to perform near real-time pointwise calculation for duration from daily to annual; (3) the ability to integrate and interactively explore large-scale heterogeneous geospatial data. (4) the ability to calculate solar irradiation at arbitrary surface positions including at rooftops, facades and the ground. Solar3D is publicly available at https://github.com/jian9695/Solar3D.

The cutting-edge photovoltaic cells are an indispensable part of the ongoing progress of earth-friendly plans for daily life energy consumption. However, the continuous electrical demand that extends to the night time requires a prior deployment of efficient real-time storage systems. In this regard, metal-air batteries have presented themselves as the most suitable candidates for solar energy storage, combining extra lightweight with higher power outputs and promises of longer life cycles. Scientific research over non-precious functional catalysts has always been the milestone and still contributing significantly to exploring new advanced materials and moderating the cost of both complementary technologies. Metal-organic frameworks (MOFs) derived functional materials have found their way to the application as storage and conversion materials, owing to their structural variety, porous advantages, as well as the tunability and high reactivity. In this review, we provide a detailed overview of the latest progress of MOF-based materials operating in metal-air batteries and photovoltaic cells.

The outdoor field test of the 4-terminal on Si tandem photovoltaic module (specifically, InGaP/GaAs on Si) was investigated and performance model, considering spectrum change affected by fluctuation of atmospheric parameters, was developed and validated. The 4-terminal on Si tandem photovoltaic module had about 40 % advantage in seasonal performance loss compared with standard InGaP/GaAs/InGaAs 2-terminal tandem photovoltaic module. This advantage is expanded in (subarctic zone) < (temperate zone) < (subtropical zone). The developed and validated model used all-climate spectrum model and considered fluctuation of atmospheric parameters, and can be applied every type of on-Si tandem solar cells.

Review of the existing bibliography shows that the direction and magnitude of the long-term trends of UV irradiance, and their main drivers, vary significantly throughout Europe. Analysis of total ozone and spectral UV data recorded at four European stations during 1996 – 2017 reveals that long-term changes in UV are mainly driven by changes in aerosols, cloudiness, and surface albedo, while changes in total ozone play a less significant role. The variability of UV irradiance is large throughout Italy due to the complex topography and large latitudinal extension of the country. Analysis of the spectral UV records of the urban site of Rome, and the alpine site of Aosta reveals that differences between the two sites follow the annual cycle of the differences in cloudiness and surface albedo. Comparisons between the noon UV index measured at the ground at the same stations and the corresponding estimates from the DWD forecast model and OMI/Aura observations reveal differences of up to 6 units between individual measurements, which are likely due to the different spatial resolution of the different datasets, and average differences of 0.5 – 1 unit, possibly related to the use of climatological surface albedo and aerosol optical properties in the retrieval algorithms.

The gap in knowledge regarding the radiative effects of aerosols in the UV region of the solar spectrum is large, mainly due to the lack of systematic measurements of the aerosol single scattering albedo (SSA) and absorption optical depth (AAOD). In the present study, spectral UV measurements performed in Thessaloniki, Greece by a double monochromator Brewer spectrophotometer in the period 1998 - 2017 are used for the calculation of the aforementioned optical properties. The main uncertainty factors have been described and there is an effort to quantify the overall uncertainties in SSA and AAOD. Analysis of the results suggests that the absorption by aerosols is much stronger in the UV relative to the visible. SSA follows a clear annual pattern ranging from ~0.7 in winter to ~0.85 in summer at wavelengths 320 – 360 nm, while AAOD peaks in summer and winter. The average AAOD for 2009 – 2011 is ~50% above the 2003 – 2006 average, possibly due to increased emissions of absorbing aerosols related to the economical crisis and the metro-railway construction works in the city center. A detailed analysis of the uncertainties in the retrieval of the SSA and the AAOD from the Brewer spectrophotometer has been also performed.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.