Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

Access to medicines is one of the essential problems in Public Health of low- and middle-income countries (LMICs). The World Health Organization (WHO) defines access to medicines as the possibility of "having continuously accessible and affordable medicines in public or private health facilities that are within a kilometer of the place of residence." Access to medicines, as defined by the WHO, is not fully guaranteed in many LMICs and even in many regions of high-resource countries. The WHO identifies several factors as determinants of limitations in the access to medicines: rational selection, affordable prices, sustainable financing, and reliable health services. The action on these factors makes it possible to improve universal access to medicines with consequent improvement in Public Health. Adequate access to antibiotics and vaccination will avoid a large part of the deaths caused by infectious diseases in the LMICs. However, the emergence of resistance and the difficulties in vaccination campaigns due to socio-political or cultural problems make it challenging to fight many easily treatable infectious diseases. The use and abuse of antibiotics are inevitably associated with the appearance of resistances that make them ineffective. Thus, whereas limited access to antibiotics raises mortality rates from infectious diseases, generalized open access to them ends up eliminating their clinical value. Moreover, the contraction of research in this field for many years has reduced the success in discovering new drugs. Additionally, local market regulations, inadequate selection, inaccessible prices, especially for those of second and third-generation, inefficient health systems, and difficulties of administration and control of prescription compliance, especially in the case of combined therapies, are additional obstacles to universal access to antibiotics. In order to simultaneously improve access to antibiotics and keep resistances under control, it is necessary to develop training and education activities at different social levels (from patients to various Health Care Providers) to complement the national or supranational strategic plans.

Neuropsychiatric manifestations of COVID-19 include delirium, general malaise, headache, and psychiatric symptoms. These manifestations are related to the neuroinflammatory response to viral antigens and proinflammatory mediators/immune cells. Tetracyclines, such as minocycline, have antibacterial and anti-inflammatory properties. Saiko-keishi-to, a traditional Japanese Kampo medicine, also has anti-inflammatory properties. Given the anti-inflammatory properties of minocycline and Saiko-keishi-to, we describe two cases of COVID-19 with prolonged headaches and general malaise successfully treated with these medications.

This study aims to describe the commitment to national heritage, patriotism, nationalism of elementary school students in the border areas between Indonesia and Timor Leste. This research was conducted in three elementary schools, they are SD Inpres Moto Ain, SD Inpres Class Jau Halimuti, SD Kristen Nanaeklot, and SD Negeri Motabenar from June to August 2018. The subjects of this study were elementary students in the Indonesia-Timor Leste border areas precisely around Motaain City, Belu Regency, East Nusa Tenggara. The research questionnaire was adapted from Karazawa and analyzed with descripriptive statistics. The results of this study showed that the commitment to national heritage, patriotism, and nationalism of elementary students on the Indonesian border areas with Timor Leste is in the very high level.

Abstract: The expansion of global industries results in the release of harmful volatile acid vapors into the environment, posing a threat to various life forms. Hence, it's crucial to prioritize the development of swift sensing systems capable of monitoring these volatile acid vapors. This initiative holds great importance in safeguarding a clean and safe environment. This paper presents the synthesis and characterization of pyrene-based covalent organic frameworks (COFs) demonstrating exceptional crystallinity, thermal stability, and intense fluorescence. Three COFs—PP-COF, PT-COF, and PE-COF—were synthesized, showcasing large surface areas and robust thermal stability up to 400 °C. The fluorescence properties and intramolecular charge transfer within these COFs were significantly influenced by their Schiff base bonding types and π-stacking degrees between COF layers. Notably, PE-COF emerged as the most fluorescent among the three COFs and exhibited exceptional sensitivity and rapid response as a fluorescent chemosensor for detecting HCl in solution. The reversible protonation of imine bonds in these COFs allowed for the creation of highly sensitive acid vapor sensors, showcasing a shift in spectral absorption while maintaining structural integrity. This research highlights the potential of COFs as reliable and reusable sensors for detecting harmful acid vapors, addressing environmental concerns arising from industrial activities.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

With the wide application of flow sensor, their reliability under extreme conditions has been concerned in recent years. The reliability of a Micro Electro Mechanical Systems flow sensor under temperature (Ts) is researched in this paper. Firstly, the Step-stress accelerated degradation test is designed. Because this flow sensor consists flow sensor chip and signal processing system, the accelerated degradation testing is implemented, respectively. While the results show that the biggest drift is 3.15% for flow sensor chips with 150℃ conditions, and 32.91% for this flowmeter. By analysis, it could be found that the attenuation of the signal processing system is significant to the degeneration of this flowmeter. The minimum drift of the signal processing system accounts for 82.01% of this flowmeter. Secondly, using the Coffin-Manson model, the relationship between cycle-index and Ts is established. And the lifetime with different Ts is estimated by the Arrhenius model. In addition, the Weibull distribution is applied to evaluate the lifetime distribution. Finally, the reliability function of the Weibull distribution is demonstrated, and the survival rate within one year is 87.69% with 85℃ conditions. Thus, by the application of accelerated degradation testing, the acquired results are innovative and original. This research illustrates the reliability research, which provides a relational database for the application of this flow sensor.

Virtual validation of radar sensor models is becoming increasingly important for the safety validation of adf. Therefore, methods for quantitative comparison of radar measurements in the context of model validation need to be developed. This paper presents a novel methodology for accessing and quantifying validation measurements of radar sensor models. This method uses edf and the so-called dvm to effectively quantify deviations between distributions. By applying this metric, the study measures the consistency, reproducibility and repeatability of radar sensor measurements. Different interfaces and different levels of detail are investigated. By comparing the radar signals from real world experiments where different objects are present, valuable insights are gained into the performance of the sensor. In particular, the research extends to assessing the impact of varying rain intensities on the measurement results, providing a comprehensive understanding of the sensor’s behaviour under these conditions. This holistic approach significantly advances the evaluation of radar sensor capabilities and enables the quantification of the maximum required quality of radar simulation models.

Antioxidants are very beneficial for health because they protect the body from the effects of free radicals on various degenerative diseases caused by food contamination, air pollution, sunlight, etc. In general, methods for measuring the capacity of antioxidants generally use accurate meth-ods such as spectrophotometry and chromatography. Still, it takes time, sample preparation and must be done in a laboratory with particular expertise. Therefore, a new, more practical method needs to be developed for determining antioxidants, namely the electrochemical method. The electrochemical method is promising to develop because it has several advantages, including high sensitivity and fast response. The electrochemical method discussed in this article reviews sensors, biosensors, and nanosensors. This paper comprehensively analyzes contemporary developments in electrochemical biosensor techniques and antioxidant evaluation methodologies. The discussion centers on utilizing multiple biosensors. Electrochemical biosensors have been determined to be prevalent in analyzing food quality, assessing active factor functionality, and screening practical components. The present study outlines the difficulties linked with electrochemical bio-sensor technology and provides insights into the potential avenues for future research in this domain.

In this work we successfully prepared a modified cobalt oxide (Co3O4) carbon paste electrode to detect Levofloxacin (LEV). By synthesizing Co3O4 nanoparticles through the chemical coprecipitation method, the electrochemical properties of the electrode and LEV were thoroughly investigated using CV, SWV, EIS, while material properties were scrutinized using ICP-OES, TEM, SEM, and XRD. The results showed that the prepared electrode displayed a better electrocatalytic response than the bare carbon paste electrode. After optimizing SWV, the electrode exhibited a wide linear working range from 1 to 85 μM at pH 5 of BRBS as the supporting electrolyte. The selectivity of the proposed method was satisfactory, with good repeatability and reproducibility, strongly suggesting a potential application for determining LEV in real samples, particularly in pharmaceutical formulations. The practicality of the approach was demonstrated through good recoveries, and the morphology of the materials was found to be closely related to other parameters, indicating that the developed method can provide a cost-effective, rapid, selective, and sensitive means for LEV monitoring. Overall, this project has made significant progress towards developing a reliable method for detecting LEV and has opened up new opportunities for future research in this field.

In this study, the preparation of the composite 3% Au/graphite-C3N4 (3% Au/g-C3N4) sensing material was prepared by doping 3% Au onto the surface of graphitic carbonitride (C3N4) for detection pimobendan. By the way of sensing materials characterization, the X-ray diffraction analysis (XRD) and transmission electron Microscope (TEM) were performed. The cyclic voltammetry (CV) was used to measure the concentration and redox properties of pimobendan. It can be seen that when the voltage value is 0.05 V, and a reduction peak was appeared and the pimobendan concentration (0 to 55 μM) has a relationship with the reduction current value. At low concentrations of pimobendan concentration from 0.0 to 0.8 μM, the linearity R2 = 0.9642 with a detection limit of 0.28 μM. A possible pimobendan sensing mechanism on 3% Au/g-C3N4 was proposed.

Modern agriculture demands for comprehensive information about the plant itself. Conventional chemistry-based analytical methods - due to their low throughput and high associated cost - are no longer capable of providing these data. In recent years, remote reflectance-based characterization has developed as one of the most promising solutions for rapid assessments for plant attributes. However, in many cases, expensive equipment is required because accurate quantifications need assessment of the full reflectance spectrum. We examined the versatility of visible colour sensors as reflectance measuring devices for biological / biochemical quantifications on sweet basil (Ocimum basilicum). Our results indicate for the wide potential of spectral colour sensors for quantitative determination of leaf phenolic compounds, flavonoids in particular, and non-invasive plant phenotyping in agricultural applications by low-cost sensors.

Early identification of viruses leads to more efficient disease management and control, and is extremely important. A possible new approach for creating virus sensors is the Electromagnetic echo effect (EMEE). An important feature is that the signal from EMEE is highly dependent on the state of the irradiated body. This makes it possible to control ongoing reactions, even if these reactions are invisible to the human eye or other equipment. This article shows the possibility of registering reaction occurring in the presence of an avian coronavirus causing infectious bronchitis, strain Massachusetts. The same methodology can be applied for other types of viruses as well.

Nitroxyl radical catalysts oxidize alcohols under an applied electric potential. It is possible to quantify the alcohol concentration from the resulting oxidation current. In this work, we evaluated the catalytic activity of nitroxyl radicals (or their corresponding hydroxylamines), including 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) as representative nitroxyl radicals, acetoamido-TEMPO, which shows higher oxidation potential than TEMPO owing to the acetoamido group, AZADO, Nor-AZADO, and NNO as less-hindered bicyclic nitroxyl radicals, and NHPI as an N,N-diacyl-type hydroxylamine, in acetonitrile solution. TEMPO, AZADO and NNO were also evaluated for their ability to oxidize alcohols in organic solvents, and their reactivity was compared with the electrochemical response. The most active NNO was used for electrochemical detection of cyclosporin A, a drug with a hydroxyl group.

The aim of the current study was to determine the effectiveness of two surgical techniques regarding the cow respiratory rates, heart rates, and rumination time using two sensors: an experimental device that was created by the Institute of Biomedical Engineering of Kaunas University of Technology (Lithuania) and the “SCR” (SCR Engineers Ltd., Netanya, Israel) system. The cows were divided into two groups: PA1—cows treated by percutaneous abomasopexy (n = 10), and RSO2—cows treated by right side omentopexy (n = 8). For the control group (KH), according to the principle of analogues (number of lactations, breed, and days in milk), we selected clinically healthy cows (n = 9). After the surgical treatment for the abomasal displacement, the experimental device was applied for the recording of the heart and breathing rates; 12 hour tracking of the rumination time (RT) was implemented using the system ''SCR''; and the body temperature was measured. After 12 hours, the blood was taken for biochemical and morphological tests. The experimental device recorded 12 hours of the respiratory rate (RR) and heart beat rate (HBR) information. We determined the concentrations of the blood serum beta-hydroxybutyrate (BHB), calcium (Ca), phosphorus (Phos), magnesium (Mg), and iron (Fe), as well as the activities of aspartarte aminotransferase (AST) and gamma-glutamyl transferase (GGT). According to searches for relationships between the traditional blood biochemical and morphological parameters, and the parameters measured by the experimental device, the more efficient abomasal displacement surgical method was the right side omentopexy. With the sensors, we found, after right side omentopexy, a 5.19 beats/min lower (1.10-times) average value of the respiratory rate, 1.13-times higher level of the heart rate, a 0.15 oC higher temperature, and a 3.29-times lower rumination time compared to the clinical healthy cows. Further research with larger numbers of animals and longer experimental periods are needed prior to practical applications.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

An antenna sensor is proposed to execute dual functions of antenna and sensor in the wireless sensor system, in order to reduce data loss and to increase transmission rate by omitting a certain interface. The as-made sensor was test at a center frequency of 46 MHz for measuring human finger postures using principle of dipole antenna. The antenna sensor was attached on a wearable glove. The results showed that the motion sensor can accurately identify finger angles at 0°, 20°, 40°, 60° and 80°.

People with Down syndrome present cognitive difficulties that affect their reading skills. In this study we present results about the use of gestural interaction with Kinect sensor to improve the reading skills of students with Down syndrome. Following a case of study method for small samples with disabilities, measuring different variables related to reading skills in an experimental group and in a control group. We found improvements in the visual association, visual comprehension, sequential memory, and visual integration after this stimulation in the experimental group compared to the control group. Also, we found that the number of error and delay time of interaction decrease between sessions in the experimental group.

The subject of the research is to Development of laser ablation method for Fabrication of surface acoustic wave sensors on quartz wafer, the target of the GQW – is to design Acoustic wave sensor by using laser ablation method. By using the surface acoustic wave theory to sense by the signal and using this physical phenomenon, We will design the sensor which transduce an input electrical signal into a mechanical wave which unlike an electrical signal, can be easily influenced by physical phenomena. The device then transducers this wave back into an electrical signal on the secondary terminal of the sensor. Changes in amplitude, phase, frequency, or time-delay between the input and output electrical signals can be used to measure the presence of the desired Our work in this part, especially the practical part like temperature, vibration ,etc. we design a combs on the waver of quartz to make like an electrode primary electrode & secondary electrode by putting coats of cuppers & vanadium on the waver and then using the fiber optic laser regime to design this combs to can able transfer the signal by ablation the most important here to use the regime of fiber optic laser then we using this sensor in any electronic circuit How we will select the suitable kind of laser to design, this is the most important part, and what it will be the diameter of that combs of secondary and primary , how much the value of the wave length to select the micro distant combs to avoid any inductance and interference for transferred signal , also take the benefit of using MEMS theory in our project.

In this work, two embroidered textile moisture sensors are characterized with three different conductive yarns. The sensors are based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidered conductor yarn. The performance comparison of 3 different type of conductive yarns has been addressed. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 30% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity and the used conductor yarns. This dependence points out the optimum conductive yarn to be used to develop wearable applications for moisture measurement.

Detection of formaldehyde is very important in terms of life protection, as it can cause serious injury to eyes, skin, mouth and gastrointestinal function if indirectly inhaled and hence researchers are putting effort in developing novel and sensitive device. In this work, we have fabricated an electro-chemical sensor in the form of a field effect transistor (FET) to detect formaldehyde over wide range (10 nM to 1 mM). For this, ZnO nanosheets (NS) were first synthesized by hydrothermal method with in-situ deposition on cleaned SiO₂ coated Si (100) substrate. The synthesized materials were characterized for morphology and purity and surface area (31.718 m²/g). The developed device was tested for formaldehyde detection at room temperature that resulted in a linear response with concentration (96%), sensitivity value of 0.27 mA/M/cm² and a low detection limit of 210 nM, and a high 0.93194 return.

This paper presents a new and enhanced fusion module for the Multi-Sensor Precipitation Estimator (MPE) that would objectively blend real-time satellite quantitative precipitation estimates (SQPE) with radar and gauge estimates. This module consists of a preprocessor that mitigates systematic bias in SQPE, and a two-way blending routine that statistically fuses adjusted SQPE with radar estimates. The preprocessor not only corrects systematic bias in SQPE, but also improves the spatial distribution of precipitation based on SQPE and makes it closely resemble that of radar-based observations. It uses a more sophisticated radar-satellite merging technique to blend preprocessed datasets, and provides a better overall QPE product. The performance of the new satellite-radar-gauge blending module is assessed using independent rain gauge data over a 5-year period between 2003-2007, and the assessment evaluates the accuracy of newly developed satellite-radar-gauge (SRG) blended products versus that of radar-gauge products (which represents MPE algorithm currently used in the NWS operations) over two regions: I) inside radar effective coverage and II) immediately outside radar coverage. The outcomes of the evaluation indicate a) ingest of SQPE over areas within effective radar coverage improve the quality of QPE by mitigating the errors in radar estimates in region I; and b) blending of radar, gauge, and satellite estimates over region II leads to reduction of errors relative to bias-corrected SQPE. In addition, the new module alleviates the discontinuities along the boundaries of radar effective coverage otherwise seen when SQPE is used directly to fill the areas outside of effective radar coverage.

The deformation of underground gateroads tends to be asymmetric and complex. Traditional instrumentation fails to accurately and conveniently monitor the full cross-sectional deformation of underground gateroads. Here, a full cross-sectional laser scanner was developed together with a visualization software package. The developed system used polar coordinate measuring method and the full cross-sectional measurement was realized by 360° rotation of laser sensor driven by an electrical motor. Later on, the potential impact of gateroad wall flatness, roughness and geometrical profile as well as coal dust environment on the performance of the developed laser scanner were evaluated. The studies show that a high-level flatness is favorable in application of the developed full cross-sectional deformation monitoring system. For a smooth surface of gateroad, the sensor cannot receive reflected light when the incidence angle of laser beam is large, causing data loss. Conversely, the roughness surface shows its priority as the diffuse reflection light can be received by the sensor. With regards to the coal dust in measurement environment, the fine particles of floating coal dust in the air can lead to the loss of measurement data to some certain due to scattering of laser beam.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

To study and monitor the adverse health consequences from using electronic cigarettes, a user’s puff topography, which are quantification parameters of the user’s vaping habits, plays a central role. In this work, we introduce a topography sensor to measure the mass of total particulate matter generated in every puff and to estimate the nicotine yield. The sensor is compact and low-cost, and is integrated into the electronic cigarette device to promptly and conveniently monitor the user’s daily puff topography. The topography sensor is comprised of a photometric sensor and a pressure sensor. The photometric sensor measures the mass concentration of the aerosol, based on scattering of near-infrared light from airborne particles, while the pressure sensor measures the flow rate. The topography sensor was experimented under various conditions with a wide range of atomizer power, puff duration, and inhalation pressure. The sensor’s accuracy was validated by comparing the sensor’s readings with reference measurements, and the results matched closely with the trends reported by existing studies on electronic cigarettes. An example application of tracking a user’s puff topography was also demonstrated. Our topography sensor holds great promise in mitigating health risks of vaping, and in promoting quality control of electronic cigarette products.

A planar microwave sensor devoted to the detection of humidity in underwear and clothes in general is proposed. The ultimate goal of the sensor is to detect the presence of liquids in fabrics, of interest to aid patients that suffer from certain pathologies, such as hyperhidrosis and enuresis. The main target in the design of the sensor, considering the envisaged application, is simplicity. Thus, the sensor operates at a single frequency, and the working principle is the variation in the mag-nitude of the transmission coefficient of a matched line loaded with an open-ended quar-ter-wavelength sensing stub resonator. The stub, which must be in contact with the so-called fabric under test (FUT), generates a notch in the transmission coefficient with a resonance frequency that depends on the humidity level of the fabric. By designing the stub with a moderately high quality factor, the variation in the resonance frequency causes a significant change in the magnitude level at the operating frequency, the resonance frequency when the sensing stub is loaded with the dry fabric, and the presence of liquid can be detected by means of an amplitude detector. A prototype device is proposed and experimentally validated.

Five years ago, the concept of addressed fiber Bragg structures (AFBS) was proposed, which simultaneously perform the functions of a two-frequency radiation shaper, the difference frequency of which is the AFBS address, and a sensitive element, since the value of the difference frequency is invariant to measured physical fields, and the set of difference frequencies, moreover, is orthogonal in the array of such sensors, enabling their address multiplexing. In this article, we provide an overview of the theory and technology of AFBS, including the structures with three or more spectral components with various combinations of difference frequencies, symmetrical and asymmetric, performing the functions of the address and converting information signals to the low-frequency range at the same time, along with other functions. The subjects of interrogation of these structures, their fabrication and calibration are discussed as well. We also consider a wide range of applications in which AFBS can be used, covering such areas as oil and gas production, power engineering, transport, medicine, etc. In addition, the prospects of AFBS further development are proposed.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

Background. IgA nephropathy (IgAN) is associated with chronic inflammation. Platelet-related parameters, such as platelet (PLT) count, platelet-to-albumin ratio (PAR) and platelet-to-lymphocyte ratio (PLR), were examined as potential prognostic indicators for renal and cardiovascular (CV) outcomes in IgAN. Methods. 150 IgAN patients were devided into two groups based on the cut-off value of PAR. All-cause mortality, major CV events and end-stage renal disease were the primary combined endpoints. Secondary endpoints, such as CV or renal endpoints, were also analyzed separately. Results. The patient’s mean age was 43.7 ± 13.5 years, and the follow-up time was 124 ± 67 months. The K-M curve showed that PLR, PAR and PLT were strongly associated with primary combined (p = 0.002, p = 0.004, p = 0.001) and renal outcomes (p < 0.001, p < 0.001, p < 0.001), but not with CV outcomes in IgAN. However, when combined with left ventricular hypertrophy (LVH) or metabolic syndrome (MetS) PAR was found to be a significant predictor of both primary (p < 0.001, p < 0.001) and secondary outcomes (p = 0.001 and p = 0.038; p = 0.001 and p = 0.015). Additionally, PLR correlated with microalbuminuria (r = -0.165, p = 0.033) and LVH (r = -0.178, p = 0.025), while PLT correlated with eGFR (r = 0.158, p = 0.040). Conclusion. Elevated PAR and PLR may predict progression to end-stage kidney disease, but in combination with LVH and MetS, they showed CV events also in IgAN. The determination of PAR and PLR can be useful and cost-effective parameters for assessing both cardiovascular and renal risks in CKD.

Background: The aim of this study has been to investigate if inflammatory biomarkers such as the systemic immune-inflammation index (SII), neutrophil to lymphocyte ratio (NLR) and platelet to lymphocyte ratio (PLR) have any correlation with the recurrence of pleomorphic adenomas (PA) in patients afflicted by this disease. Methods: A retrospective multicentre study involving two Italian centres, the Maxillofacial Sur-gery at the Policlinico Federico II in Naples and the ENT and Maxillofacial Surgery at the IRCCS G. Pascale National Cancer Institute in Naples, has been performed. The study, involving 608 pa-tients who had received a diagnosis of PA, was conducted between January 2000 and January 2020. A Receiver Operating Characteristic (ROC) curve was used to calculate the optimal cut-off values for the SII, PLR and NLR. A linear regression model (LRM) and a non-linear logistic re-gression model (NLRM) were realized with respect to the NLR, PLR and SII. Results: The highest performance was achieved by the NLR (cut-off 2.960) with the AUC = 0.91, with an accuracy of 96.1%, sensitivity of 78.4% and specificity of 97.2%, PPV = 64.4% and NPV = 98.6%. The LRM and NLRM including all the haematological parameters did not increase the per-formance in terms of recurrence detection. Conclusion: The NLR is an excellent support tool in predicting the recurrence of PA with a cut-off of 2.960. It can be a good reference point for surgical decision-making and follow-up in clinical practice.

Clofazimine and Arbidol have both been reported to be effective in vitro SARS-CoV-2 fusion inhibitors. Both are promising drugs repurposed for treatment of COVID-19 and have been used in several previous and ongoing clinical trials. Small-molecule binding to expressed constructs of the trimeric S2 segment of Spike and the full-length SARS-CoV-2 spike protein were measured using a Surface Plasmon Resonance (SPR) binding assay. We demonstrate that Clofazimine, Toremifene, Arbidol and other Arbidol derivatives bind to the S2 segment of the Spike protein. Clofazimine provided the most reliable and highest quality SPR binding data to S2 over the conditions explored. A molecular docking approach was used to identify the most favorable binding sites on the S2 segment in the prefusion conformation, highlighting two possible small-molecule binding sites for fusion inhibitors. Results from molecular docking and modeling the structure-activity-relationship (SAR) of a newly reported series of Clofazimine derivatives supports the proposed Clofazimine binding site on the S2 segment. When the proposed Clofazimine binding site is superimposed with other experimentally determined coronavirus structures in structure-sequence alignments, the changes in sequence and structure may rationalize the broad-spectrum antiviral activity of Clofazimine in closely related coronavirus such as (SARS-CoV, MERS, hCoV-229E, hCoV-OC43).

Background: Tuberculosis (TB) continues to be a serious public health threat that affects the most vulnerable population. Patients who are LTFU after TB diagnosis still represent one of the biggest challenges to TB control. Method: In this prospective observational study, we aimed to identify and analyse the risk factors associated with LTFU among TB patients who started first-line TB treatment in the Sanatorium Hospital in Luanda. Result: A total of 113 patients with TB were included between August 2018 and September 2019. Seventy-six (67.3%) patients were cured, 27 (23.9%) were LTFU, 5 (4.4%) died, 4 (3.5%) were transferred and 1 (0.9%) presented a treatment failure. After excluding those dead, transferred or who failed to treatment, we observed that severe TB at the time of diagnosis (OR 9.24, 95% CI 2.18-39.04) and food insecurity were significantly associated with LTFU (OR 5.96, 95% CI 1.66-21.41). Conclusion: The findings of our study are of enormous value to understand the reasons for the LTFU of patients with TB and can guide polices and facilitate designing measures to allow better adherence, and therefore, greater treatment success

Breast cancer (BC) affects millions of women; it is the leading cause of death by neoplasia in wom-en worldwide, with at least 500 thousand deaths each year, 70% of which occur in developing countries. Elastography evaluates tissue stiffness, making this a promising non-invasive real-time technique. BI-RADS is recognized as a standard and helpful technique for establishing BC risk. This study aimed to determine, by strain elastography (SE), the fat-to-lesion index (F/L index), sen-sitivity, specificity, and optimal cut-off to diagnose BC. This prospective study included 216 wom-en who underwent SE, ultrasound, mammography, and breast biopsy; according to mammogra-phy, we recruited BI-RADS category 2 (n= 5), category 3 (n=29), category 4 (n= 94), category 5 (n= 71) and category 6 (n=17); after biopsy, 108 women were classified as negative, and 108 were pos-itive for BC. Three expert BC radiologists performed all imaging interpretations and biopsies. Our results show mean values of the F/L index for negative biopsies of 3.70±2.57 and positive biopsies of 18.10±17.01; we developed two models for the prediction of BC, a logistic regression model with an AUC of 0.893 and a neural network with an AUC of 0.902. The Youden index yielded a F/L index cut-off >5.76, with a sensitivity and specificity of 84.26%. Positive Spearman's Rho cor-relation coefficient was observed between the F/L index and BI-RADS, r=.073 (p< 0.001). ANOVA test showed a difference between F/L index vs. molecular subtypes (p=0.002). SE is helpful as a di-agnostic complement to mammography, or in cases where the latter is contraindicated, elas-tography has an adequate predictive capacity and is a fast and minimally invasive procedure.

It has been proposed that upregulation of the noradrenergic (NA) system through exposure to novelty might be one of the key components for building cognitive reserve and resilience to neurodegeneration. A personality trait that promotes greater interest in novel experiences is Openness to Experience (OE). Individuals who are high in OE exhibit strong curiosity towards novelty and are more likely to be exposed to novel stimuli throughout the lifespan.Performing voxel-based morphometry analyses, we examined whether OE in 135 healthy young adults was associated with Locus Coeruleus (LC) - the main core of the noradrenergic system. We also investigated whether LC mediates the relationship between OE and a key measure of reserve, I.Q. In comparison with other neuromodulators’ seeds (Dorsal and Median Raphe [DR-MR] -5-HT, Ventral Tegmental Area [VTA] -DA- and Nucleus Basalis of Meynert [NBM] -Ach-), results show that greater LC integrity was related to greater OE and IQ. Additionally, mediation analyses revealed that only LC mediated the relationship between OE and IQ. Furthermore, a Bayesian multiple regression was conducted to model the contribution of both isolated and combined neuromodulator seeds to OE trait express. This approach found that the LC + VTA could account for more variance in OE expression compared to the LC alone. Other weaker but significant associations were observed between DR and OE, between LC + NBM and Conscientiousness and between DR + NBM and Extraversion. These results are together suggestive that OE is primarily underpinned by monoaminergic functioning, and that the LC-NA system plays a central role mediating the interdependence between OE expression and cognition (IQ level). While offering further understanding of the neurobiology of human personality, these findings indicate a pivotal role of LC-NA system integrity in novelty seeking in daily life. This provides a psychobiological account for how OE expression may be beneficial for maintaining the noradrenergic system to facilitate cognitive reserve and resilience to neurodegenerative conditions.

This paper compares the performance of three text-to-speech (TTS) models released from June 2021 to January 2022 in order to establish a baseline for Brazilian Portuguese. Those models were trained using dataset for Brazilian Portuguese. The experimental setup considers tts-portuguese dataset to fine-tune the following TTS models: VITS end-to-end model; glowtts and gradtts acoustic models both using hifi-gan vocoder. Performance metrics are arranged into objective and subjective metrics. As subjective metrics, the naturalness and intelligibility are measured based on the mean opinion score (MOS). Results shows that gradtts+hifigan model achieved naturalness of 4.07 MOS, close to performance of current commercial models.

Background: Vaccinating children against COVID-19 is an essential public health strategy in order to reach herd immunity and prevent illness among children and adults. Parents are facing tremendous stress in relation to the COVID-19 pandemic and the effectiveness of the COVID-19 vaccination program for children. In this study, we aimed to investigate parents’ willingness to vaccinate their children against COVID-19 in North Kivu province (DRC). Methods: A cross-sectional survey between December 01, 2021 to January 20, 2022 in 6 health zones (Goma, Karisimbi, Butembo, Beni, Kamango and Katwa) was conducted in the province of North Kivu. In each health zone, we selected 5 clusters (Health area) using the method of probabilistic selection proportional to population size. In total, 522 parents participated in our study. Results: Overall, 32.8% of parents intended to vaccinate their children. In the multivariate analysis, younger age of parents (aOR : 2.40, CI : [1.50-3.83]), higher level of fear that “a member of my family” could contract COVID-19 (aOR : 2.35, CI : [1.38-4.02]), higher level of perceived vulnerability to COVID-19 within the family (aOR : 1.70, CI : [1.005-2.2881]), higher level of perceived susceptibility to COVID-19 within the family (aOR : 3.07, CI : [1.80-5.23]), and history of vaccination against COVID-19 among parents (aOR : 16.47, CI : [8.39-32.33]), were significantly associated with the intention to have their children or adolescents vaccinated. Conclusion: Willingness of parents to vaccinate their children against the COVID-19 vaccination was low in North Kivu. There is undeniably in this region a need to reinsure the populations about vaccine safety for both children and adults. Public health authorities should also address widespread misinformation about vaccines in a timely manner.

With the COVID-19 pandemic continuing and the resulting economic burden increasingly apparent, the Indonesian government began to prepare a "new normal" phase and make peace with COVID-19. From this new decision arises the question of the readiness of businesses and the industrial sector to resume operations amid COVID-19. This article aims to provide concise and precise information about the preparations that can be made by businesses to operate safely amid COVID-19 based on existing scientific studies and literatures. From the literature visits it can be concluded that transmission and danger of a COVID-19 pandemic can be prevented through: creation of infectious disease prevention and response plan, implementing basic infection prevention measures, policies and procedures for proper identification and isolation of sick people, applying flexibilities in policies, and protections in the workplace.

Here we review and describe a set of research priorities to meet present and future challenges posed to farmed animal production that build on progress, successes and resources from the Functional Annotation of ANimal Genomes (FAANG) project.

South America has become the new epicenter of the coronavirus, especially in Brazil where the disease continues to spread exponentially across the country. This text aims to analyze the psychosocial factors of Covid-19 on back to school strategies in Brazil from a bioecological perspective. At the microsystem level, the population is experiencing different levels of stress and fear; at the mesosystem level, changes in routines, separation from family and friends, and closure of schools; and at the macrosystem level, national guidelines to control the pandemic, institutional standards on a national and international scale. Therefore, the main focus for the success of school return must be in the prevention of contagion and with physical and psychological health, and should not only consider the demands of curricula, financial or administrative management. For this reason, it is paramount that greater female representativeness is increased in decision-making levels of the meso and macrosystem, regarding the resumption of school and academic activities in the pandemic period, since the number of female leaders in decision-making, is still insufficient.

The COVID-19 pandemic has presented the world with increased challenges. The response to this pandemic has led to a sudden disruption of routine medical and elective surgical care. Most hospitals across the globe have had to change the way outpatient clinics are carried out and postpone non-urgent elective surgical procedures. NHS England ceased all elective general surgeries to train and re-deploy their staff to support the increased pressures from COVID-19 in an intensive care setting. However, with a decline of reported cases and deaths, the return to undertaking non-urgent elective services is imminent. In May 2020, Radha and Afzal published the first evidence-based guidelines for the resumption of elective orthopaedic services titled “Evidence based suggestions for the return to elective orthopaedic surgery following the COVID-19 Pandemic”. The pathway presented is adapted from the “Evidence based suggestions for the return to elective orthopaedic surgery following the COVID-19 Pandemic” and could potentially be used as a model for other surgical specialities. We present a three-phased return back to urological services. Safe resumption of elective care is possible but needs to be carefully planned.

Most large fibers in central nervous system of vertebrates are decussated. The cause or the evolutionary force of this phenomenon is not convincingly described. Here we show a pattern for this nervous system property that simultaneously is found to a more basic rule in evolution.The idea here is the "function to anatomy" theorem. We claim that functions of physical, biochemical, enzymatic, etc., in lower scale of living organisms "emerge" to anatomy in larger scales. And reversely, the anatomy we see in multicelular organisms are/were functions in microscopic scales.We propose descriptions, predictions, and a probable road map to what this can implicate in biological and medical issues.

In 2014, the outbreak of adenoviral pneumonia occurred in Korean military training center. However, there is limited data on characteristics of fever and its response to antipyretics therapy in immunocompetent adults with adenoviral positive community-acquired pneumonia (CAP). Medical records of patients who were admitted to Armed Forces Chuncheon Hospital for treatment of CAP between January 2014 and December 2016 were retrospectively analyzed. We evaluated demographics, clinico-laboratory findings and radiologic findings at admission were compared between adenovirus positive (Adv) group and adenovirus negative (non-Adv) group. Out of 251 military personnel with CAP during the study periods, 67 were classified into Adv group while 184 were Non-Adv group. Patients with Adv group had a longer duration of fever after admission and symptom onset. Adv group patients had a higher mean temperature at admission and more observed over 40 and 39 to 40℃. Adv group patients had more commonly observed no response to antipyretic treatment and adverse events after antipyretics use. Length of hospital stay had no significant difference between two groups and no patient died in both groups. In our study, Adv positive CAP in patients with immunocompetent military personnel had distinct characteristics of fever and response to antipyretic treatment.

An understanding of the cultural conditions that determine the factors affecting nurses’ intention to leave is important for countries suffering from nurse shortage. Aim: to examine factors influencing intention to leave among female hospital nurses in a large Japanese sample, classified into four generations by age considering economic conditions. Methods: a cross-sectional survey with convenience sampling was conducted. Anonymous self-administered questionnaires were distributed to all nurses in 30 hospitals. To assess intention to leave, basic attributes, life conditions, work characteristics, and factors of psychosocial work environment were addressed. After classifying data into four generations based on age cohorts, we conducted multivariate logistic regression analysis using the completed data (N = 5,074, mean age = 36.24). Results: regardless of generational characteristics influenced by economic conditions, effort and monetary reward were generation-common factors. Over-commitment, social support, and the presence of a role model were generation-common factors in three generations. While having children increased intention to leave in the generation born 1965–1979, having family members in need of caregiving other than children decreased the risk in the generation born in the 1980s. Conclusion: generational countermeasures considering factors of psychosocial work environment and life conditions are needed to avert female nurse turnover.

Microaggressions are subtle verbal and non-verbal slights based on group membership, and they are ubiquitous in the lives of racial minorities, women, and LGBTQ individuals (Sue, 2010). The goal of the current paper is to introduce a role-playing based exercise on effective responses to microaggressions. The workshop draws on the prejudice responding workshops of Plous (2000) and Lawson, et al. (2010) but integrates research-based strategies. The activity was tested in two groups of undergraduate students, and the findings suggested that both groups felt more prepared to deal with microaggressions after participating.

Monochromatic documents claim for much less computer bandwidth for network transmission and storage space than their color or even grayscale equivalent. The binarization of historical documents is far more complex than recent ones as paper aging, color, texture, translucidity, stains, back-to-front interference, kind and color of ink used in handwritting, printing process, digitalization process, etc. are some of the factors that affect binarization. This article presents a new binarization algorithm for historical documents. The new global filter proposed is performed in four steps: filtering the image using a bilateral filter, splitting image into the RGB components, decision-making for each RGB channel based on an adaptive binarization method inspired by Otsu's method with a choice of the threshold level, and classification of the binarized images to decide which of the RGB components best preserved the document information in the foreground. The quantitative and qualitative assessment made with 21 binarization algorithms in three sets of “real world” documents showed very good results.

HER2/neu positive breast tumors predict a high mortality and comprise 25-30% of breast cancer. We have shown that Flavokawain A (FKA) preferentially reduces the viabilities of HER2 overexpressing breast cancer cell lines (i.e. SKBR3 and MCF7/HER2) versus those with less HER2 expression (i.e. MCF7 and MDA-MB-468). FKA at cytotoxic concentrations to breast cancer cell lines also has minimal effect on the growth of non-malignant breast epithelial MCF10 cells. FKA induces G2M arrest in cell cycle progression of HER2 overexpressing breast cancer cell lines through inhibition of Cdc2 and Cdc25C phosphorylation and down-regulation of Myt1 and Wee1expression leading to increased Cdc2 kinase activities. In addition, FKA induces apoptosis in SKBR3 cells by increasing the protein expression of Bim and BAX and decreasing expression of Bcl₂, Bcl_x/L , XIAP and survivin. FKA also down-regulates the protein expression of HER-2 and inhibits AKT phosphorylation. Herceptin plus FKA treatment leads to enhanced growth inhibitory effect on HER-2 overexpressing breast cancer cell lines through down-regulation of Myt1, Wee1, Skp2, Survivin and XIAP. Our results suggest the promise of FKA as a novel apoptosis inducer and G2 checkpoint abrogating agent in combination with Herceptin for treatment of HER2 overexpressing breast cancer.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

Biometric fingerprint identification hinges on the reliability of its sensors, however, calibrating and standardizing these sensors poses significant challenges, particularly in regard to repeatability and data diversity. To tackle these issues, we propose methodologies for fabricating synthetic 3D fingerprint targets, or phantoms, that closely emulate real human fingerprints. These phantoms enable the precise evaluation and validation of fingerprint sensors under controlled and repeatable conditions. Our research employs laser engraving, 3D printing, and CNC machining techniques, utilizing different materials. We assess the phantoms' fidelity to synthetic fingerprint patterns, intra-class variability, and interoperability across different manufacturing methods. The findings demonstrate that a combination of laser engraving or CNC machining with silicone casting produces finger-like shaped phantoms with high accuracy and consistency for rolled fingerprint recordings. For slap recordings, direct laser engraving of flat silicone targets excels and in the contactless fingerprint sensor setting, 3D printing and silicone filling provides the most favorable attributes. Our work enables a comprehensive, method-independent comparison of various fabrication methodologies, offering a unique perspective on the strengths and weaknesses of each approach. This facilitates a broader understanding of fingerprint recognition system validation and performance assessment.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Effective detection of isopropyl methylfluorophosphonate (GB, sarin), a type of organophosphine poisoning agent, is an urgent issue to be addressed in maintaining public safety. In this research, a gas-sensitive film material defined as poly (4-hydroxy-4,4-bis trifluoromethyl) - butyl-1-enyl) - si-loxane (SXFA) with the structure of hexafluoroisopropyl (HFIP) functional group was synthesized by using methyl vinylpropyl dichlorosilane and hexafluoroacetone trihydrate as initial materials. Synthesis process products were characterized by FTIR. SXFA was prepared on a 200 MHz shear surface wave delay line with spin coating method for GB detected. Detection limit of ＜ 0.1 mg/m3 was obtained through conditional experiments. Meanwhile, we also obtained the maximum re-sponse of 2.168 mV at 0.1 mg/m3 concentration, which indicting a much lower detection limit of SAW-SXFA sensor. Additionally, the maximum response standard deviation of 0.11 mV with a co-efficient of variation of 0.01, as well as the maximum recovery standard deviation of 0.22 mV with a coefficient of variation of 0.02 were also obtained through 5 repeated experiments. Results showed that the SAW-SXFA sensor has strong selectivity and reproducibility, good selectivity, positive detection ability, high sensitivity, and fast alarm performance for sarin detection.

Ischemia, the inadequate blood flow, can arise from pre-existing or traumatic events, remain an undetectable issue, and impact the body's ability to provide oxygen to necessary limbs, organs, muscles, or tissue. New technology involving wearable ultrasonic devices allows medical professionals to gain real-time insight into the cardiovascular system of their patients. A non-invasive, postage-stamp-sized ultrasonic sensor can be attached to a patient, allowing for continuous monitoring of the patient’s blood pressure outside of the hospital. After reviewing 16 papers on ultrasonic sensors, this paper intends to review the current use of wearable ultrasonic sensors and the advantages and limitations of the technology used to obtain accurate blood pressure readings. This review will bring attention to the evolving and expanding world of wearable ultrasonic sensors for medical applications.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

In this work, we propose an approach for the autonomous navigation of mobile robots using fusion of sensor data by a Double Deep Q-Network with collision avoidance by detecting moving people via computer vision techniques. We evaluate two data fusion methods for the proposed autonomous navigation approach: Interactive and Late fusion strategy. Both are used to integrate mobile robot sensors through the following sensors: GPS, IMU and, an RGB-D camera. The proposed collision avoidance module is implemented along with the sensor fusion architecture in order to prevent the autonomous mobile robot from colliding with moving people. The simulation results indicate a significant impact on the success of completing the proposed mission by the mobile robot with the fusion of sensors, indicating a performance increase (success rate) of 27% in relation to navigation without sensor fusion. With the addition of moving people in the environment, deploying the people detection and collision avoidance security module has improved about 14% the success rate when compared to that of the autonomous navigation approach without the security module. Video was developed with robot navigation using the DDQN-Late Fusion https://www.loom.com/share/684afa6a5b0148afadc9a200ab9f3483.

In this paper, we introduced a comprehensive study, based on both numerical and experimental analyses, of side polished (SP) single mode fibers (SMF) to investigate their evanescent field interaction with air and liquid analytes. In particular, the finite element method (FEM) and the beam propagation method (BPM) are employed to predict the optical properties of the SP-SMF. An ad-hoc experimental setup has been designed and built to characterize the side polished single mode fiber when air, water, and isopropanol are set in the side polished region. The sensitivity of the analytes is obtained as 1.207 V/RIU. The performance in terms of effective refractive index and transmittance are reported to show how these SP-SMF can be efficiently used for calculating the liquid refractive index. The simulation and experimental results display the significant performance of the SP-SMF as a sensing element.

Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. Recent advances in air quality monitoring have produced portable, easy-to use, low-cost, sensor-based monitors, which has given a new dimension to the air pollutant monitoring and has democratized the air quality monitoring process by making monitors and results directly available at community level. This study used PurpleAir(c) sensors for PM2.5 assessment in California, USA. Evaluation of PM2.5 from sensors included Quality Assurance &amp; Quality Control (QAQC) procedures, assessment with respect to reference monitored PM2.5 concentrations, and formulation of a decision support system integrating these observations using geostatistical techniques. The hourly and daily average observed PM2.5 concentrations from PurpleAir monitors followed the trends of observed PM2.5 at regulatory monitors. PurpleAir monitored PM2.5 also captured the peak PM2.5 concentrations due to incidents like forest fire. In comparison with reference monitored PM2.5 levels, it was found that PurpleAir PM2.5 concentrations were mostly higher. The most important reason for PurpleAir higher PM2.5 concentrations was the inclusion of moisture or water vapor as aerosol in contrast to measurements of PM2.5 excluding water content in FEM/FRM and non-FEM/FRM monitors. On long term assessment (2016-2020), R2 was between 0.54 and 0.86 at selected collocated PurpleAir and regulatory monitors for hourly PM2.5 concentrations. Past research studies have been conducted for mostly shorter time periods (&lt;3-4 months) that resulted in higher R2 values between 0.80 to 0.98. This study aims to provide reasonable estimations of PM2.5 concentrations with high spatiotemporal resolutions based on statistical models using PurpleAir measurements. The methods of Kriging and IDW, geostatistical interpolation techniques, showed similar spatio-temporal patterns. Overall, this study revealed that low-cost, sensor based PurpleAir sensors could be effective and reliable tools for episodic and long-term ambient air quality monitoring.

This chapter aims to construct a relatively complete, universal, and highly reliable road surface state monitoring and perception system through the research of the A1 contact road reconstruction project of an international airport (hereinafter referred to as the “airport”). The system design is based on on-the-spot investigation, theoretical analysis, and engineering practice, using vibrating string type and resistive strain sensors as sensing means, real-time high-frequency signal acquisition technology as the guide, 4G router for wireless communication technology as the media, and storage technology for monitoring system based on server storage terminals. In combination with engineering background, aircraft motion state, main landing gear configuration, sensor selection and evaluation, and other major factors, the actual monitoring information needs of the plane are fully taken into account, as well as the difference in sensor information types, and the system design is carried out by stratification and classification.

Detecting low concentrations of thyroxine hormone (T4) is of utmost importance to prevent diseases and medical issues caused by hypothyroidism. In this work, we propose the use of a simple technique for T4 sensing, the well-known surface-enhanced Raman spectroscopy (SERS). Spherical Au and Ag nanoparticles (NPs) and functionalized with ascorbic acid and tannic acid, respectively. They synthesized by a seed-mediated growth method, were used as SERS substrates to quantify T4 at different concentrations. The NPs were characterized by UV-VIS spectroscopy and scanning electron microscopy. Both, Au and Ag NPs, have an average diameter of 50 nm, the first ones have a surface plasmon resonance at 537 nm, while the latter have it at 421 nm. It was noticed the SERS substrates are composed of isolated and agglomerated NPs. From theoreti-cal-numerical calculations, we identified the hot spots |E| of the agglomerate NPs is at least 7 times more intense than that of the isolated NPs. We show the substrates can detect up to 0.01 mM and, for the range of concentration studied, the Ag substrate is more sensitive than Au. Thus, the proposed substrates and the SERS technique constitute a potential prospect for sensing hormones and organic molecules at low concentrations.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

The fourth industrial revolution, also known as Industry 4.0, has led to an increased transition towards automation and reliance on data-driven innovations and strategies. Companies in the manufacturing sector are heavily integrating Industry 4.0 technologies, including cloud compu-ting, cyber-physical systems (CPS), big data analytics, horizontal and vertical system integration, the internet of things (IoT), and additive manufacturing (3d printing). The interconnected systems and processes have significantly increased operational efficiency, enhanced organizational capacity to monitor and control functions, reduced costs, and improved product quality. One significant way that companies have achieved these benefits is by integrating diverse sensor technologies within these innovations, allowing critical data collection on products, equipment performance, and maintenance. The sensors connect systems and machines, allowing them to communicate and track operations for enhanced operations. While numerous research has been conducted to show the role of sensors in industry 4.0, limited studies show how these innovations can leverage product design to maximize benefits and opportunities. Given the rapidly changing market conditions, Industry 4.0 requires new products and business models to ensure companies adjust to the current and future changes. These requirements call for the evolutions in product design processes to accommodate design features and principles applicable in the current dynamic business environment. This research paper employs a systematic bibliometric literature review (LRSB) methodology to explore and synthesize data on how Industry 4.0 and sensors can leverage product design. The results show that various product design features create opportunities to be leveraged to guarantee the success of Industry 4.0 and sensor technologies. However, the research also identifies numerous challenges that undermine the ongoing transition towards intelligent factories and products.

Glyphosate　(GLYP)　is a broad-spectrum, non-selective, organic phosphine post emergence herbicide registered for use on many food and non-food field. Herein, we developed a biosensor (Mbs@dsDNA) based on carboxylated modified magnetic beads incubated with NH2-polyA and then hybridized with polyT-glyphosate aptamer and complementary DNA. Afterward, a quantitative detection method based on qPCR was established.　When the glyphosate aptamer on Mbs@dsDNA specifically recognized glyphosate, a complementary DNA is released and then enters the qPCR signal amplification process. The linear range of the method was 0.1-5 μg/mL, and the detection limit was set at 0.1 μg/mL. The recoveries in tap water were ranged from 103.4 ~ 104.9%, and the relative standard deviations (RSDs) were < 1%. The aptamer proposed in this study has a good potential for recognizing glyphosate. The detection method combined with qPCR might have a good application prospect in detecting and supervising other pesticide residues.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

The increasingly affordable price point of terrestrial laser scanners has led to a democratization of instrument availability, but the most common low-cost instruments have yet to be compared in terms of the consistency to measure forest structural attributes. Here, we compared two low-cost terrestrial laser scanners (TLS): the Leica BLK360 and the Faro Focus 120 3D. We evaluate the instruments in terms of point cloud quality, forest inventory estimates, tree-model reconstruction, and foliage profile reconstruction. Our direct comparison of the point clouds showed reduced noise in filtered Leica data. Tree diameter and height were consistent across instruments (4.4% and 1.4% error, respectively). Volumetric tree models were less consistent across instruments, with ~29% bias, depending on model reconstruction quality. In the process of comparing foliage profiles, we conducted a sensitivity analysis of factors affecting foliage profile estimates, showing a minimal effect from instrument maximum range (for forests less than ~50 m in height) and surprisingly little impact from degraded scan resolution. Filtered unstructured TLS point clouds must be artificially re-gridded to provide accurate foliage profiles. The factors evaluated in this comparison point towards necessary considerations for future low-cost laser scanner development and application in detecting forest structural parameters.

We consider the problem of calibrating distance measurement of Light Detection and Ranging (lidar) sensor without using additional hardware, but rather exploiting assumptions on the environment surrounding the sensor during the calibration procedure. More specifically we consider the assumption of calibrating the sensor by placing it in an environment so that its measurements lie in a 2D plane that is parallel to the ground, and so that its measurements come from fixed objects that develop orthogonally w.r.t. the ground, so that they may be considered as fixed points in an inertial reference frame. We moreover consider the intuition that moving the distance sensor within this environment implies that its measurements should be such that the relative distances and angles among the fixed points above remain the same. We thus exploit this intuition to cast the sensor calibration problem as making its measurements comply with this assumption that “fixed features shall have fixed relative distances and angles”. The resulting calibration procedure does thus not need to use additional (typically expensive) equipment, nor deploying special hardware. As for the proposed estimation strategies, from a mathematical perspective we consider models that lead to analytically solvable equations, so to enable deployment in embedded systems. Besides proposing the estimators we moreover analyse their statistical performance both in simulation and with field tests, reporting thus the dependency of the MSE performance of the calibration procedure as a function of the sensor noise levels, and observing that in field tests the approach can lead to a ten-fold improvement in the accuracy of the raw measurements.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 0.8x1e6 Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer or simulant Urine) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

Paper-based sensors, microfluidic platforms and electronic devices have attracted attention in the past couple of decades because they are flexible, can be recycled easily, environmentally friendly, and inexpensive. Here we report a paper aptamer-based potentiometric sensor to detect the whole Zika virus for the first time with a minimum sensitivity of 2.6 nV/Zika and the minimum detectable signal (MDS) of 1.2x10⁶ Zika. Our paper sensor works very similar to a P-N junction where a junction is formed between two different wet regions with different electrochemical potentials near each other on the paper. These two regions with slightly different ionic contents, ionic species and concentrations, produce a potential difference given by the Nernst equation. Our paper sensor consisted of a 2-3 mm x 10 mm segments of a paper with a conducting silver paint contact patches on its two ends. The paper is soaked in a buffer solution containing aptamers designed to bind to the capsid proteins on Zika. Atomic force microscopy studies were carried out to show both the aptamer and Zika become immobilized in the paper. We then added the Zika (in its own buffer) to the region close to one of the silver-paint contacts. The Zika virus (40 nm diameter with 43 kDa or 7.1x10^-20 gm weight), became immobilized in the paper’s pores and bonded with the resident aptamers creating a concentration gradient. The potential measured between the two silver paint contacts reproducibly became more negative as upon adding the Zika. We also showed that an LCD powered by the sensor, can be used to detect the sensor output.

A method for infrared and cameras sensor fusion, applied to indoor positioning in intelligent spaces, is proposed in this work. The fused position is obtained with a maximum likelihood estimator from infrared and camera independent observations. Specific models are proposed for variance propagation from infrared and camera observations (phase shifts and image respectively) to their respective position estimates and to the final fused estimation. Model simulations are compared with real measurements in a setup designed to validate the system. The difference between theoretical prediction and real measurements is between 0.4 cm (fusion) and 2.5 cm (camera), within a 95% confidence margin. The positioning precision is in the cm level (sub-cm level can be achieved at most tested positions) in a 4x3 m locating cell with 5 infrared detectors on the ceiling and one single camera, at distances from target up to 5 m and 7 m respectively. Due to the low cost system design and the results observed, the system is expected to be feasible and scalable to large real spaces.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

In this work, an embroidered textile moisture sensor is presented. The sensor is based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidery conductor yarn composed by 99% pure silver plated nylon yarn 140/17 dtex. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 25% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity. Moreover, the reproducibility of the sensor performance subject to the manufacturing process variability and washing process is also evaluated. The results show that the manufacturing variability introduce a moisture measurement error up to 4%. The washing process impact on the sensor behavior after applying the first washing cycle implies a sensitivity reduction higher than 14%. Despite these effect, the textile sensor keeps its functionality and can be reused in standard conditions. Therefore, these properties point out the usefulness of the proposed sensor to develop wearable applications on health and fitness scope including the user needs to have a life cycle longer than one-time use

Multiple sensor nodes known as detection stations make the sensor networks; each node is light and portable. Every sensor node contains power source, microcomputer, transducer and transceiver. Power source provides power to each node. Micro-computer is used for storing and processing the output coming from the sensors. The transducer is used to generate the signals and the transceiver is used to receive and transmit data to the central computer. Eavesdropping gets facilitated with wireless communication, and it has many useful applications in military, homeland, hostile and uncontrolled environments. So it is prone to the high level of security. The process in which information is gathered to form a summarized type for analysis is known as data aggregation, as it is used to reduce the energy consumption in wireless sensor networks. The security issues have become crucial in data aggregation, especially when gets deployed in hostile and remote environment. In wireless sensor networks many secure aggregations have been proposed. It still faces some resource constrained that’s why new techniques are needed. In our survey we will discuss those approaches and their pros and cons.

Neutrophil to lymphocyte ratio (NLR) is a promising predictive and prognostic factor in breast cancer. We investigated its ability to predict disease-free survival (DFS) and overall survival (OS) in patients with luminal A or luminal B-HER2-negative breast cancer who received neoadjuvant chemotherapy (NACT). Pre-treatment complete blood cell counts from 168 consecutive patients with luminal breast cancer were evaluated to assess NLR. The study population was stratified into NLRlow or NLRhigh according to a cut-off value established by receiving operator curve (ROC) analysis. Data on additional pre- and post-treatment clinical-pathological characteristics were also collected. Kaplan-Meier curves, log-rank tests, and Cox proportional hazards models were used for statistical analyses. Patients with pre-treatment NLRlow showed a significantly shorter DFS (HR 6.97, 95% CI 1.65-10.55, p= 0.002) and OS (HR 7.79, 95% CI 1.25-15.07, p= 0.021) compared to those with NLRhigh. Non-ductal histology, luminal B subtype, and post-treatment Ki67≥ 14% were also associated with worse DFS (p= 0.016, p= 0.002, and p= 0.001, respectively). In multivariate analysis, luminal B subtype, post-treatment Ki67≥ 14%, and NLRlow remained independent prognostic factors for DFS, while only post-treatment Ki67≥ 14% and NLRlow affected OS. The present study provides evidence that pre-treatment NLRlow helps identify women at higher risk of recurrence and death among patients affected by luminal breast cancer treated with NACT.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

Identifying macroeconomic events that are responsible for dramatic changes of economy is of particular relevance to understand the overall economic dynamics. We introduce an open-source available efficient Python implementation of a Bayesian multi-trend change point analysis which solves significant memory and computing time limitations to extract crisis information from a correlation metric. Therefore, we focus on the recently investigated S&P500 mean market correlation in a period of roughly 20 years that includes the dot-com bubble, the global financial crisis and the Euro crisis. The analysis is performed two-fold: first, in retrospect on the whole dataset and second, in an on-line adaptive manner in pre-crisis segments. The on-line sensitivity horizon is roughly determined to be 80 up to 100 trading days after a crisis onset. A detailed comparison to global economic events supports the interpretation of the mean market correlation as an informative macroeconomic measure by a rather good agreement of change point distributions and major crisis events. Furthermore, the results hint to the importance of the U.S. housing bubble as trigger of the global financial crisis, provide new evidence for the general reasoning of locally (meta)stable economic states and could work as a comparative impact rating of specific economic events.

The migration from MATLAB to Python (M-to-PY) has gained significant traction in recent computational research. While MATLAB has long served as a linchpin in myriad scientific endeavors, there's an emerging trend to rejuvenate these projects using Python's extensive AI tools and libraries. This study presents a semi-automated process for M-to-PY conversion, using a detailed case study of an image skeletonization project comprising fifteen MATLAB files and a 1404-image dataset. Skeletonization is foundational for ongoing 3D motion detection research using AI transformers, predominantly developed in Python. The utilization of ChatGPT-4, acting as an AI co-programmer, is pivotal in this conversion. By leveraging the public OpenAI API, we developed an M-to-PY converter prototype, evaluated its efficacy using test cases from the Bard bot, and subsequently employed the converted code in an AI application. The dual contributions encompass a well-tested M-to-PY converter and a Skeleton App capable of sketching and skeletonizing any given image, enriching the AI toolset. This study accentuates how AI resources, like ChatGPT-4, can simplify code transitions, opening doors for innovative AI implementations using primarily MATLAB-coded scientific research.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

The world has been highly impacted by the COVID-19 as the virus has spread to all continents – about 200 countries in total. The latest update claims about 4,000,000 confirmed cases and about 300,000 confirmed deaths owing to the COVID-19 pandemic. This probably makes the COVID-19 as the most dangerous contagious disease in the era 2000s. Apart from massive publications on this topic, there is no available qualitative analysis that describes the dynamic spreads of the COVID-19 and its impacts on healthcare and the economy. Through the system archetypes analysis, this paper explains that the dynamic spread of the COVID-19 consists of the limits to growth and the success to successful structures. The limits to growth elucidates that more symptomatic and asymptomatic patients owing to infected droplets may be bounded by self-healing and isolated treatments. The success to successful structure explains that once the COVID-19 affects the economy through the lockdown, there will be a limited fund to support the government aids and the aggregate demand. In overall, this paper gives readers simplified holistic insights into understanding the dynamic spread of the COVID-19.

Background Telomere shortening is related to aging and unfavourable health outcomes. Obesity and metabolic diseases are important factors for accelerating aging. This study aimed to find out the association between obesity, metabolic disease, and telomere length in metabolically healthy adults. Methods 237 adults were enrolled with written consents at a health promotion centre of a tertiary hospital from February 2014 to March 2015. After excluding 99 subjects who met the exclusion criterion, a total of 130 metabolically healthy subjects were selected for final analysis. The subjects were divided into quartile groups according to the telomere lengths of their oral mucosal cells. Results The subjects consisted of 66 (50.8%) males with a mean age of 58.59 years. The body mass index (BMI, kg/m2) increased significantly along with the quartile groups (Q1, 23.00; Q2, 23.96; Q3, 23.70; Q4, 25.20; P-for trend=0.008). Waist circumference (WC, P-for trend=0.022), waist-to-hip ratio (WHR, P-for trend=0.005), and waist-to-height ratio (WHtR, P=0.001) also increased along with the quartile groups. Obesity prevalence (BMI ≥25 kg/m2), abdominal obesity (WC ≥90 cm for men, ≥85 cm for women), WHR 〉1.0 for men or 〉0.85 for women, and WHtR ≥0.5 increased significantly as the telomere length increased (P-for trend <0.05). After adjusting for covariates, the ORs for each obesity markers increased as the telomere length increased (P-for trend <0.05); and the ORs of WHtR were especially meaningful (Q1, 1.00; Q2, 2.53; Q3, 2.97; Q4, 7.81; P-for trend = 0.001). There were no significant trends for metabolic syndrome and its components along with the prevalence of fatty liver disease. Conclusion Obesity markers and telomere length had significant positive correlation despite the established theory. The obesity paradox may exist in metabolically healthy adults with regard to telomere length, However, further studies with larger sample sizes for the association between obesity and telomere length are needed.

Background: The risk to physicians who worked with patients without confirmed COVID-19 testing during the pandemic has been little studied. However, they were at high risk. Methods: A total of 1285 Romanian physicians completed an online survey. We performed Mann-Whitney comparisons between physicians who reported that they knowingly had direct contact with COVID patients and those who didn't regarding their willingness to work. Results: Compared with their colleagues, physicians who reported not knowingly having direct contact with COVID patients reported less access to protective equipment, less overall willingness to respond when asked to work with infected patients, more likely to work out of fear of losing their jobs, and fear of legal repercussions. They received less training in the use of protective equipment. Conclusions: Physicians who worked with patients not yet diagnosed with COVID-19 were significantly less willing to work. The perception of invisible risk may explain the observed differences.

The challenge of accessing finance by entrepreneurs from traditional financial sources is pervasive. The COVID-19 pandemic further exacerbated the problem of limited access to finance from banks. Against this backdrop, the objective of the study was to determine the factors driving crowdfunding success during the COVID-19 pandemic in Africa. The ordinary least squares (OLS) and probit regression models were estimated to analyse 216 crowdfunding projects in Africa. The results of the study documented that targeted amount (TA), and COVID-19 pandemic were negative and significant drivers of crowdfunding success. Furthermore, comments (CMM) and duration (DRN) were negative and significantly affected crowdfunding success. Conversely, images (IM), videos (VD), backers (BCK), and updates (UPD) were positive and significantly affected crowdfunding success. The study contributes to the body knowledge by investigating the drivers of crowdfunding success during the COVID-19 pandemic period which hitherto had not been researched on extenisvely.

Background: Smart transport plays a crucial role in urban planning and the transition from traditional to smart cities in developing countries with sustainability requirements.Traditional cities in developing countries often suffer from traffic congestion,air pollution, and inadequate public transportation systems,which can impede economic growth and negatively impact the quality of life for residents. Smart transport solutions can address these challenges by providing more efficient, sustainable.Here is a possible business model for an ITS system in a high-potential city in Iran,Based on IoT analysis, Mashhad city in Iran selected as a high-potential city to be changed to a smart city in the transportation sector.In the localization business model,the Uber smart transportation business model as a successful world experience is considered the base model. Methods: Based on the literature review,various criteria and sub-criteria were identified and determined in designing a new localized transportation business model.A questionnaire was prepared and filled with the help of 11 experts,method IAHP technique; Results:The present study showed the possibility of monthly payments for customers,software development, and the addition of luxury cars are among the most important sub-criteria with high weights;Conclusions: Working with transport companies,schools and universities as key partners solves reaching a strong and sustainable smart transportation system.

We aimed to explore symptoms severity and adherence to therapy for patients with myelofibrosis treated with ruxolitinib in Bulgaria. It is a prospective, non-interventional study performed at the Specialized hospital for active treatment of hematological diseases in Sofia during 2022 - 2023. Date of diagnosis, demographic characteristics, clinical indicators, ruxolitinib dose, and other data points were collected. Clinical indicators were assessed at baseline, in the middle and at the end of observation. Severity of symptoms was measured with MPN-SAF TSS and adherence to therapy with the Morisky 4 questionnaire 6 times during the observation. The mean age of diagnosis was 58.5 years, with the average duration of disease of 3 years. Pa-tients’ laboratory results were within physiological ranges, with spleen size experiencing a con-stant decrease. The average value for the severity of the symptoms per MPN-SAF TSS results decreased significantly, indicating better disease control. The average adherence to therapy did not change and remained high at around 9 points, except for one patient. In conclusion the treatment of myelofibrosis patients with ruxolitinib decreased symptoms se-verity and spleen size. Patients were adherent to the therapy over the observed period but as treatment duration increases the risk of adherence decreasing.

Recent advances in deep learning technology have led to increased interest in text-to-image technology, which enables computers to create images from text by simulating the human process of forming mental images. The GAN-based text-to-image technology involves the extraction of features from input text, which are combined with noise and then used as input to a GAN that generates images that are similar to the original images through competition between the generator and discriminator. Although generating images from English text is a mature area of research, text-to-image technology based on multilingualism, such as Korean, is still in its early stages of development. Webtoon is a digital comic format that allows comics to be viewed online. The creation process for webtoons is divided into story planning, content/sketching, coloring, and background drawing. Since each stage of webtoon production requires human intervention, it is both time-consuming and expensive. As a result, deep learning technologies such as automatic coloring and automatic line drawing are being used to reduce human involvement. However, there is a shortage of technology that can assist authors with story creation in webtoon production. Therefore, this study proposes a multilingual text-to-image model capable of generating webtoon images when presented with multilingual input text. The proposed model employs Multilingual BERT to extract feature vectors for multiple languages, and trains a DCGAN in conjunction with the images. The experimental results demonstrate that the model can generate images that are similar to the original images when presented with multilingual input text after training.

Small and medium-sized enterprises (SMEs) help and support the country in financial and business aspects and employs in the country, overcomes unemployment, and creates job opportunities in different sectors of the country. The study aims to know the entrepreneurial-specific factors like age, gender, education, experience, and skills used as predictors for access to financing of small firms in Khyber Pakhtunkhwa. The questionnaire is used for data collection, and about 204 questionnaires were distributed, of which 192 returned and analyzed through binary logistic regression. The study results reveal that age and level of education have been found significant while gender, experience and skills have insignificant with the access to finance in Khyber Pakhtunkhwa, Pakistan.

Circular Economy involves structural changes in traditional business models and consumers’ behaviour toward recycled products. The recycling of PET products has been increasing but there is still a gap between consumption and demand for PET packaging in Brazil. In this research, the waste reduction was examined under a projective scenario to the current ecological purposes in Brazil for reducing environmental pollution. In that manner, this paper aimed to comprehend the intention to purchase recycled PET products of Brazilian consumers. With a non-probabilistic and convenience sample, the study counts 422 participants. The method employed was based on Structural Equation Modelling and Partial Least Squares, used to test the hypotheses of causality among the variables. Results showed the perception of low quality about recycled products reduced consumers’ intention to purchase. Also, the sustainability of recycled products positively influenced the intention to purchase. In addition, recycled products presented a negative impact on the perceived safety, which could influence the purchase of recycled products in Brazil. We conclude that the image that Brazilian consumers have about recycled products positively affects the intention to purchase.

The origin of cancer remains one of the most important enigmas in modern biology. The prevailing paradigm has failed to grasp a comprehensive view of the disease. Naturally, therapies developed under the current assumptions are inadequate and cancer is practically an incurable disease. Meanwhile, descriptive studies continuously extend the molecular complexity of cancer without an equivalent advancement in its understanding. Furthermore, they tend to accumulate inconsistencies inexplicable under the classical view. This paper presents a compelling theory of the origin of carcinomas. By hypothesis, a series of generic events in epithelial tissues promoted by cellular aging and inflammation enables the reactivation of developmental programs. The origin of carcinomas in vivo is described as the time-ordered cell state transitions undergone by epithelial cells in the hyperplasia due to replicative senescence and inflammation towards a mesenchymal undifferentiated endogenous cell state with cancerous behavior. In support of the theory, the molecular, cellular, and histopathological evidence is critically reviewed. A plausible model for the origin of carcinomas is presented to explain the mechanism underlying carcinogenesis from an evolutive and developmental perspective. The implications of the hypothesis in the current strategies for cancer prevention and treatment are discussed along with rational alternatives and some predictions for possible experimental validation.

Microbial symbioses exhibit astounding adaptations, yet all symbionts face the problem of how to reliably associate with host offspring every generation. A common strategy is vertical transmission, in which symbionts are directly transmitted from the female to her offspring. The diversity of symbionts and vertical transmission mechanisms is as expansive as the diversity of eukaryotic host taxa that house them. However, there are several common themes among these mechanisms based on the degree to which symbionts associate with the host germline during transmission. In this review, we detail three distinct vertical transmission strategies, starting with associations that are transmitted from host somatic cells to offspring somatic cells, either due to lacking a germline or avoiding it. A second strategy involves somatically-localized symbionts that migrate into the germline during host development. The third strategy we discuss is one in which the symbiont maintains continuous association with the germline throughout development. Unexpectedly, the vast majority of documented vertically inherited symbionts rely on the second strategy: soma-to-germline migration. Given that not all eukaryotes contain a sequestered germline and instead produce offspring from somatic stem cell lineages, this soma-to-germline migration is discussed in the context of multicellular evolution. Lastly, as recent genomics data have revealed an abundance of horizontal gene transfer events from symbiotic and non-symbiotic bacteria to host genomes, we discuss their impact on eukaryotic host evolution.

Bidirectional gene promoters affect the transcription of two genes, leading to the hypothesis that they should exhibit protection against genetic or epigenetic changes in cancer. Therefore, they provide an excellent opportunity to learn about promoter susceptibility to somatic alteration in tumors. We tested this hypothesis using data from genome-scale DNA methylation (14 cancer types), simple somatic mutation (10 cancer types), and copy number variation profiling (14 cancer types). For DNA methylation, the difference in rank differential methylation between tumor and tumor-adjacent normal matched samples based on promoter type was tested by Wilcoxon rank sum test. Logistic regression was used to compare differences in simple somatic mutations. For copy number alteration, a mixed effects logistic regression model was used. The change in methylation between non-diseased tissues and their tumor counterparts was significantly greater in single compared to bidirectional promoters across all 14 cancer types examined. Similarly, the extent of copy number alteration was greater in single gene compared to bidirectional promoters for all 14 cancer types. Furthermore, among 10 cancer types with available simple somatic mutation data, bidirectional promoters were slightly more susceptible. These results suggest that selective pressures related with specific functional impacts during carcinogenesis drive the susceptibility of promoter regions to somatic alteration.

The traditional herbal medicine, Hochu-ekki-to, has been shown to have preventive effects on viral infection and stress. This study aimed to evaluate the clinical effects of Hochu-ekki-to on two stress-related rat models of polycystic ovarian syndrome. Female Sprague-Dawley rats were divided into control and treatment groups, the latter of which were subjected to stress induced by exposure to adrenocorticotropic hormone (ACTH) or cold temperatures. After these stress inductions, rats were orally treated with dissolved Hochu-ekki-to once per day for 7 days. Rats subjected to the two different stressors exhibited upregulation of steroid hormone receptors (in ovaries) and reproductive hormones (in blood), and consequent stimulation of abnormal follicle development accompanied by elevation of Hsp 90 expression (in ovaries). Treatment with Hochu-ekki-to for 7 days after stress induction increased immune functions, reduced the stress-induced activation of Hsp 90, and normalized the levels of the tested steroid hormone receptors and reproductive hormones. Our findings suggest that stress stimulations may promote the activation of Hsp 90 via the dysregulation of steroid hormone receptors and reproductive hormones, but that post-stress treatment with Hochu-ekki-to improves reproductive and immune functions in the ovaries of stressed rats.

Accurately predicting the distance an object will travel to its destination is very important in various sports. Acceleration sensors as a means of real-time monitoring are increasingly gaining increasing attention in sports. Due to the low energy output and power density of Triboelectric Nanogenerators (TENGs), recent efforts have focused on developing various acceleration sensors. However, these sensors suffer from significant drawbacks of large size, complexity, high power input requirements, and high cost. Here, we described a portable and cost-effective real-time refreshable strategy design comprising a series of individually addressable and controllable units based on TENGs embedded in a flexible substrate. This results in a highly sensitive, low-cost, and self-powered acceleration sensor. Putting, which accounts for nearly half of the strokes played, is obviously an important component of the golf game. The developed acceleration sensor has an accuracy controlled within 5 %. The initial velocity and acceleration of the forward movement of a rolling golf ball after it is hit by a putter can be displayed, and the stopping distance quickly calculated and predicted in about 7 seconds. This research demonstrates the application of the portable TENG-based acceleration sensor, while paving the way for designing portable, cost-effective, scalable, and harmless ubiquitous self-powered acceleration sensors.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

Conventional methods for pathogen detection in water rely on time-consuming enrichment steps followed by biochemical identification strategies, which require assay times ranging from 24 hours to up to a week. However, in recent years, significant efforts have been made towards the development of biosensing technologies enabling rapid and close-to-real-time detection of waterborne pathogens. In previous studies, we developed a plastic optical fiber (POF) immunosensor using an optoelectronic configuration consisting of a U-Shape probe connected to an LED and a photodetector. Bacterial detection was evaluated with the immunosensor immersed in a bacterial suspension in water with a known concentration. Here, we report on the sensitivity of a new optoelectronic configuration consisting of two POF U-Shape probes, one as the reference and the other as the immunosensor, for the detection of Escherichia coli. In addition, another way of detection was tested where the sensors were calibrated in the air, before immersed in bacterial suspension and then read in the air, making the immunosensor more sensitive and with a faster detection time. This new sensor detected the presence of E. coli at 104 CFU/mL in less than 10 minutes. Currently sub 10 minutes is faster than previous studies using fiber-optic based biosensors. It is also a much simpler and quicker methodology when compared with conventional laboratory technology.

Rainwater infiltration presents substantial challenges for urban wastewater management systems. This article delves into enhancing the quality of wastewater systems by proposing a novel device designed to tackle this issue comprehensively. The focal point of our research revolves around the conceptualization, construction, rigorous testing, and the potential multifaceted applications of this innovative wastewater device. Our study is dedicated to assessing the viability of a cutting-edge apparatus that empowers municipal entities in swiftly identifying rainwater ingress points within channels during precipitation events. Our findings vividly showcase the device's remarkable capability to directly measure moisture levels along the channel's path, eliminating the arduous need for manual data input, extensive data collection, and intricate water analysis procedures. To ensure the seamless flow of both sewage and water within the sewer channel, the use of a relatively slender strap is conventionally favored. However, factoring in the requisite structural robustness, we recommend a minimum thickness of 4 mm for 3D printing applications. For instances where maintaining the channel's cross-sectional area integrity is paramount, opting for a armlet with wet circuit measurement thickness of up to 7 mm is prudent. In the realm of material selection, our investigation advocates for the utilization of PC/ABS (polycarbonate/ Acrylonitrile Butadiene Styrene), ABS, ASA (Acrylonitrile Styrene Acrylate), or HIPS (High Impact Polystyrene) for the strap housing. For sewer diameters surpassing 315 mm, the application of thin-walled PVC (Poly Vinyl Chloride) emerges as a practical recommendation. Notably, the incorporation of PVC flat bars is discouraged, as their presence might potentially hinder the fluidity of sewage flow, thereby compromising the precision of wet circuit measurements. The pivotal innovation lies in the armlet with wet circuit measurement system, harboring immense potential for broad-scale integration across municipal facilities. This solution emerges as a streamlined and efficient strategy, offering a comprehensive avenue for continuously monitoring, fine-tuning, and optimizing the structural soundness and operational efficacy of sewer systems.

Buildings are responsible for approximately 40% of the world’s energy consumption and 36% of the total carbon dioxide emissions. Building occupancy is essential, enabling Occupant-Centric Control for zero emissions and decarbonization. Although existing machine learning and deep learning methods for building occupancy prediction have achieved remarked progress, their analyses remain limited when applied to complex real-world scenarios. Besides, there is a high expectation for Transformer algorithms to predict building occupancy accurately. Therefore, this paper presents an Occupancy Prediction Transformer network (OPTnet). We fuse and feed multi-sensor data (building occupancy, indoor environmental conditions, HVAC operations) into a Transformer model to forecast the future occupancy presence in multiple zones. We perform experimental analysis and compare it to different occupancy prediction methods (e.g., Decision Tree, Long Short-Term Memory networks, Multi-layer perceptron) and diverse time horizons (1,2,3,5,10,20,30mins). The performance metrics (e.g., Accuracy and Mean Squared Error) are employed to evaluate the effectiveness of prediction algorithms. Our OPTnet method achieves superior performance on our experimental two-week data compared to existing methods. The improved performance signifies its potential to enhance HVAC control systems and energy optimization strategies. We will make the code publicly available at https://github.com/kailaisun/occupancy-prediction-binary to promote transparency and reproducibility.

Soluble noble metal salts are widely used for loading noble metals as nano-catalysts in many applications. In this paper, Pt-SnO2 composite nanoceramics were prepared from SnO2 nanoparticles and H2PtCl6 using two Pt-loading methods separately: For the solution reduction method, the H2PtCl6 solution was added to a suspension of SnO2 and zinc powder to form Pt on SnO2 nanoparticles; and for the impregnation method, Pt was formed from H2PtCl6 in the course of sintering. Although a series of samples prepared using both Pt loading methods showed a strong response to H2 at room temperature, the ones prepared using the solution reduction method exhibited much better room temperature hydrogen sensing characteristics. For two samples of 0.5 wt% Pt and sintered at 825°C, the response value for the sample prepared using the solution reduction method was 5300 to 1% H2-20% O2-N2, which was much larger than that of 150 for the sample prepared using the impregnation method. Samples prepared using the two Pt loading methods have similar microstructures as characterized by XRD, FESEM, EDS, TEM, and HRTEM. However, the residual chlorine content in those using the impregnation method was found to be higher than that using the solution reduction method through analysis. It is proposed that the striking difference in the room temperature hydrogen sensing characteristics among samples prepared using these two different Pt loading methods separately resulted from their different chlorine removal process. This study demonstrates the importance of a proper method in loading noble metals from their soluble salts as nano-catalysts in many applications.

Pipe leakage is an inevitable phenomenon in water distribution networks (WDNs), leading to energy waste and economic damage. Leakage events can be reflected quickly by pressure values, and the deployment of pressure sensors is significant for minimizing the leakage ratio of WDNs. Concerning the restriction of realistic factors, including project budgets, available sensor installation locations, and sensor fault uncertainties, a practical methodology is proposed in this paper to optimize pressure sensor deployment for leak identification in terms of these realistic issues. Two indexes are identified to evaluate the leak identification ability, that is, detection coverage rate (DCR) and total detection sensitivity (TDS), and the principle is to determine priority to ensure an optimal DCR and retain the largest TDS with an identical DCR. Leakage events are generated by a model simulation and the essential sensors for maintaining the DCR are obtained by subtraction. In the event of a surplus budget, and if we suppose the partial sensors have failed, then we can determine the supplementary sensors that can best complement the lost leak identification ability. Moreover, a typical WDN Net3 is employed to show the specific progress, and the result shows that the methodology is largely appropriate for real projects.

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

Acoustic energy mapping provides the functionality to obtain characteristics of acoustic sources, such as: presence, localization, type and trajectory of sound sources. Several beamforming-based techniques can be used for this purpose, however, they rely on the difference of arrival times of the signal at each capture node (or microphone), so it is of major importance to have synchronized multi-channel recordings. A Wireless Acoustic Sensor Network (WASN) can be very practical to install when used for mapping the acoustic energy of a given acoustic environment. However, they are known for having low synchronization between the recordings from each node. The objective of this paper is to characterize the impact of current popular synchronization methodologies as part of the WASN to capture reliable data to be used for acoustic energy mapping. The two evaluated synchronization protocols are: Network Time Protocol (NTP) y Precision Time Protocol (PTP). Additionally, three different audio capture methodologies were proposed for the WASN to capture the acoustic signal: two of them, recording the data locally and one sending the data through a local wireless network. As a real-life evaluation scenario, a WASN was built using nodes conformed by a Raspberry Pi 4B+ with a single MEMS microphone. Experimental results demonstrate that the most reliable methodology is using the PTP synchronization protocol and audio recording locally.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.