Accurate monthly runoff estimation is fundamental in water resources management, planning, and development, resulting in preventing and reducing water-related problems, such as flooding and drought. This article evaluates the performance of the monthly hydrological rainfall-runoff model, GR2M model, in Thailand's southern basins. The GR2M model requires only two parameters, and no prior research has been reported on its application in this region. The 37 runoff stations, which are distributively located in three sub-watersheds of Thailand's southern region, namely; Thale Sap Songkhla, Peninsular-East Coast, and Peninsular-West Coast, were selected as study cases. The available monthly hydrological data of runoff, rainfall, air temperature from the Royal Irrigation Department (RID) and the Thai Meteorological Department (TMD) were collected and analyzed. Thornthwaite method was utilized for the determination of evapotranspiration. The model's performance was conducted using three statistical indices: Nash-Sutcliffe Efficiency (NSE), Correlation Coefficient (r), and Overall Index (OPI). The model's calibration results for 37 runoff stations gave the average of NSE, r, and OPI of 0.637, 0.825, and 0.757, and those values for verification of 0.465, 0.750, and 0.639, respectively. It indicated a model's acceptable performance and could apply the GR2M model for determining monthly runoff variation in this region. The spatial distribution of X1 and X2 values was conducted by using IDW method. It was susceptible to the X1 value and X2 value of approximately more than 0.90 gave the higher model's performance.

Despite increased global interest in the impacts of natural disasters on tourism, less study executes exploring how tourism sensitivity is addressed at the destination level. Generating a link between tourism and natural disaster management is vital in places that rely heavily on tourism and are prone to natural hazards. Ranau, Sabah (Malaysia) is one of the disaster-prone tourists' destination area. Hence, this paper applies the case study of Ranau earthquake 2015 to explore tourism sensitivity towards natural disasters. A qualitative of in-depth interview is applied to acquire information needed from the Ranau tourism entrepreneurs and operators. To analyse the qualitative data, a thematic analysis is conducted. Overall findings show that tourism activity in Ranau are identified to be sensitive towards the 2015 earthquake with a significant percentage of sensitivity level on two elements. These elements are known as Source and Power. The Source element includes tourism products, size of business, development, and natural disasters management with a significant sensitivity compared to the Power element (social capital). This provides insight to the need of specific tourism system adaptation as response to the earthquake and considering the integration of natural disaster management into tourism development to enhance long term sustainability.

We applied a framework to assess climate change vulnerability of 52 major vegetation types in the western United States to provide spatially-explicit input to adaptive management decisions. The framework addressed climate exposure and ecosystem resilience; the latter derived from analyses of ecosystem sensitivity and adaptive capacity. Measures of climate change exposure used observed climate change (1981-2014) and then climate projections for the mid-21st century (2040-2069 RCP 4.5). Measures of resilience included (under ecosystem sensitivity) landscape intactness, invasive species, fire regime alteration, and forest insect & disease risk, and (under adaptive capacity), measures for topo-climate variability, diversity with functional species groups, and vulnerability of any keystone species. Outputs are generated per 100km² hexagonal area for each type. As of 2014, moderate climate change vulnerability was indicated for >50% of the area of 50 of 52 types. By the mid-21^st century, all but 19 types face high or very high vulnerability with >50% of the area scoring in these categories. Measures for resilience explain most components of vulnerability as of 2014, with most targeted vegetation scoring low in adaptive capacity measures and variably for specific sensitivity measures. Elevated climate exposure explains increases in vulnerability between the current and mid-century time periods.

Background: Detection of small proportion of serious bacterial infections (SBI) with potentially life threating course in a large group of children with fever admitted to emergency department (ED) is still complicated. Measurement of immature granulocytes (IG) percentage may be used as a marker of bacterial infections. The aim of the study was to evaluate whether the IG percentage is a useful additional predictive marker of SBI. Methods: This study included 258 children with febrile infections admitted to the ED. Clinical follow-up, microbiological and radiological tests were used as reference standards for the definition of SBI. Study population was categorized into two groups: (i) infected patients with no suspicion of SBI (n = 75); (ii) patients with suspicion of SBI (n = 183). IG percentage, white blood cell count (WBC) and C-reactive protein (CRP) levels were analyzed from the first routine blood samples at hospital admission. Results: A statistically significant difference in IG percentage levels was observed in children with SBI and those without - the mean IG percentage was 1.2% for the SBI group, 0.3% for those without SBI. The cutoff level of IG percentage to predict SBI was 0.45 (84% specificity, 66% sensitivity, 90% positive predictive value). We combine variables and evaluate their additive values. The sensitivity of WBC to detected SBI improved from 74% to 85% when IG percentage was added to the prediction models. When CRP, WBC and IG percentage were combined, the sensitivity to predict SBI increased to 93%, the specificity to 86%. (95% CI 77–93%). Receiver operator characteristic analysis to predict SBI showed an area under the curve (AUC) of 0.80 for IG percentage. Conclusion: Addition of IG percentage to traditionally used markers of SBI as WBC and CRP may help to identify children with serious bacterial infections. Furthermore IG percentage can be rapidly obtained from the traditional full blood count without any extra sampling and costs.

Pseudomonas aeruginosa is an antibiotic-resistant priority pathogen as listed by the World Health Organization. P. aeruginosa, a gram-negative, rod-shaped bacterium, is frequently encountered in hospital settings as an opportunistic pathogen in nosocomial infections. P. aeruginosa has shown high antibiotic resistance, which has been attributed to several mechanisms, such as intrinsic, acquired, and adaptive resistance. This study investigates several genes which may be attributed to the acquisition of antibiotic resistance in the bacteria P. aeruginosa, as it transitions from its planktonic form to the more threatening and resistant biofilm form. Subsequently, the study assesses the comparative efficacy of three antibiotics, Ofloxacin (OFX), Tobramycin (TOB), and Ceftazidime (CAZ), in altering the expression levels of the identified multidrug efflux pump genes associated with the ability to extrude antibiotics from the cell when in the biofilm form. Efflux transporter gene expression in P. aeruginosa was conducted via extraction of total RNA in planktonic and biofilm- both untreated and treated - with Tobramycin (TOB), Ofloxacin (OFX), and Ceftazidime (CAZ). Real-time quantitative reverse transcriptase PCR was employed to analyze alterations in expression levels of the Mex A, Mex B, Mex X, Mex Y, OprM, and RPSL genes in the collected samples. In samples where no antibiotics were administered, an increase in expression of the Mex B efflux pump gene was observed compared to all other efflux pump genes in the biofilm form, providing multidrug resistance when active. The gene of interest, Mex B, was assessed for antibiotic resistance by P. aeruginosa culturing in the planktonic and biofilm forms with simultaneous treatment with TOB, OFX, and CAZ. Of the three antibiotics used, OFX showed more effectiveness in preventing biofilm growth by reducing the expression level of the Mex B efflux pump gene in the biofilm form, making P. Aeruginosa more antibiotic sensitive to OFX. TOB has similar results compared to OFX but was slightly less effective in reducing the expression of Mex B. Conversely, CAZ was not effective in reducing expression of the Mex B gene in the biofilm form or the planktonic form and was determined to be ineffective at eradicating the organism.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double <100> and <111> fiber and a unique component of (001)<110>, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

University course scheduling (UCS) is one of the most important and time-consuming issues that all educational institutions face yearly. Most of the existing techniques to model and solve UCS problems have applied approximate methods, which are different in terms of efficiency, performance, and optimization speed. Accordingly, this research aims to apply an exact optimization method to provide an optimal solution to the course scheduling problem. In other words, in this research, an integer programming model is presented to solve the USC problem. In this model, hard and soft constraints include the facilities of classrooms, courses of different levels and compression of students' curriculum, courses outside the faculty and planning for them, and the limited time allocated to the professors. The objective is to maximize the weighted sum of allocating available times to professors based on their preferences in all periods. To evaluate the presented model's feasibility, it is implemented using the GAMS software. Finally, the presented model is solved in a larger dimension using a real data set from a college in China and compared with the current program in the same college. The obtained results show that considering the mathematical model's constraints and objective function, the faculty courses' timetable is reduced from 4 days a week to 3 working days. Moreover, master courses are planned in two days, and the courses in the educational groups do not interfere with each other. Furthermore, by implementing the proposed model for the real case study, the maximum teaching hours of the professors are significantly reduced. The results demonstrate the efficiency of the proposed model and solution method in terms of optimization speed and solution accuracy.

: Intracellular tripeptide glutathione is an important agent of cell survival in hypoxia. Glutathione covalently binds to SH-groups of hemoglobin cysteine residues, protecting them from irreversible oxidation and changes its affinity to oxygen. Reduced glutathione (GSH) can also form a non-covalent complex with hemoglobin. Previously, we showed that hemoglobin tetramer has four noncovalent binding sites of glutathione GSH molecules inside, two of which are released during hemoglobin transition to deoxy form. In this study, we characterized the conserved cysteine residues and residues of non-covalent glutathione binding sites in the sequences of a number of hypoxia tolerant and hypoxia-sensitive mammals. The alpha subunit of all species considered was found to have no conserved cysteines, whereas the beta subunit contains Cys94 residue, which is conserved across species and whose glutathionylation changes the affinity of hemoglobin for oxygen 5-6-fold. In addition, the key residues of noncovalent glutathione binding sites in both alpha and beta subunits are absolutely conserved in all species considered, suggesting a common mechanism of hemoglobin redox regulation for both hypoxia-sensitive and hypoxia-tolerant mammals. The solvent accessibility of all HbA and HbB residues in oxy- and deoxy- forms was analyzed. The key residue betaCys94 is solvent accessible only in the deoxy form.

Background: Patients with severe chronic kidney disease (CKD G4-G5) often have chronically elevated high-sensitivity cardiac troponin T (hs-cTnT) values above the 99th percentile of the upper reference limit. In these patients, optimal cutoff levels for diagnosing non-ST-elevation acute cor-onary syndrome (NSTE-ACS) requiring revascularization remain undefined. Methods: Of 11,912 patients undergoing coronary angiography from 2012 to 2017 for suspected NSTE-ACS, 325 (3%) had severe CKD. Of these, 290 with available serial hs-cTnT measurements were included and 300 matched patients with normal renal function were selected as a control cohort. Results: Diagnostic performance for patients with severe CKD was high at presentation and similar to that of the control population (AUC, 95% CI: 0.81, 0.75-0.87 versus 0.85, 0.80-0.89, p=0.68) and the ROC-derived cutoff value at presentation was 4 times higher compared to the conventional 99th percentile. Combining the ROC-derived cutoff levels for hs-cTnT at presentation and absolute 3-hour changes, sensitivity increased to 98%, PPV and NPV improved up to 93% and 86%, re-spectively. (4) Conclusions: In patients with severe CKD and suspected ACS the diagnostic accu-racy of hs-cTnT for the diagnosis of NSTE-ACS requiring revascularization is improved by using higher assay specific cutoff levels combined with early absolute changes.

Numerous studies were published suggesting that troponin level is related to adverse outcomes in chronic cardiac and non-cardiac conditions. Our study investigated whether troponin levels gathered from an unselected blood sample taken during outpatient care are associated with adverse outcomes in a population with stable coronary artery disease. In a cohort of 949 patients with stable coronary artery disease, average age of 67.5 ± 9.5 years, 69.5% male, 52.1% diabetics, 51.6% with previous myocardial infarction, 57.9% with triple-vessel disease, 21.7% of patients encountered new events during an average period of monitoring of 2.07 ± 0.81 years. Troponin I/99th percentile categorized into tertiles emerged as an independent predictor of death and combined events risk (hazard ratio: 2.02 (1.13-3.60), p=0.017; 2.30 (1.37-3.88, p=0.002, respectively). A troponin ratio > 0.24 was able to identify 53.3% of patients at risk of death and heart failure hospitalization. In patients with stable coronary artery disease and adherent to treatment, troponin level is independently associated with death and heart failure hospitalization in a medium-term follow up.

Although wheat is used worldwide as a staple food, it can give rise to adverse reactions, for which the triggering factors have not been identified yet. These reactions can be caused mainly by kernel proteins, both gluten and non-gluten proteins. Among these latter, -amylase/trypsin inhibitors (ATI) are involved in baker’s asthma and realistically in Non Celiac Wheat Sensitivity (NCWS). In this paper, we report characterization of three transgenic lines obtained from the bread wheat cultivar Bobwhite silenced by RNAi in three ATI genes CM3, CM16 and 0.28. We have obtained transgenic lines showing an effective decrease of the activity of target genes that, although showing a higher trypsin inhibition as a pleiotropic effect, generate a lower reaction when tested with sera of patients allergic to wheat, accounting for the important role of the three target proteins in wheat allergies. Finally, these lines show unintended changes differences in high molecular weight glutenin subunits (HMW-GS) accumulation, involved in technological performances, but do not show differences in terms of yield. The development of new genotypes accumulating a lower amount of proteins potentially or effectively involved in such pathologies, not only offers the possibility to use them as a basis for the production of varieties with a lower impact on adverse reaction, but also to test if these proteins are actually implicated in those pathologies for which the triggering factor has not been established yet.

Two-dimensional (2D) materials show advantages as surface enhanced Raman scattering (SERS) substrate over traditional noble metals, such as chemically inert flat surface and uniform SERS signals. However, due to the low density of free electrons of 2D materials, the enhancement mechanism is mainly restricted to chemical enhancement instead of electromagnetic enhancement, resulting a relatively low enhancement factor. In this work, we reported a sensitive 2D SERS substrate based on chemical vapor deposited MoN nanosheets with electromagnetic enhanced mechanism. The maximum enhancement factor can be 3×105 with a limit of detected concentration of 4×10-8 M, which is comparable to those noble metal SERS substrates without hot spots. The MoN nanosheets show strong surface plasmon resonance in the visible range as evidenced by the UV-vis absorption spectroscopy and first principle calculation. The MoN nanosheets SERS substrates exhibit excellent Raman signal uniformity within the nanosheets. Meanwhile, Distinct thickness dependent sensitivity was observed in the MoN nanosheets, higher sensitivity can be achieved by decreasing the thickness of the nanosheets. Furthermore, the MoN nanosheets SERS substrate also show high thermal stability, which can be annealed in air for more than 300℃ and maintain its SERS activity. The high stability of MoN nanosheets allows it to be reused for 20 cycles without obvious signal decay. The high sensitivity, stability, reusability and Raman signal uniformity, makes MoN nanosheets an ideal 2D SERS substrate for practical applications.

Blind image quality assessment (BIQA) aims to evaluate image quality in a way that closely matches human perception. To achieve this goal, the strengths of deep learning and the characteristics of human visual system (HVS) can be combined. In this paper, inspired by the ventral pathway and dorsal pathway of HVS, a dual-pathway convolutional neural network is proposed for BIQA task. The proposed method consists of two pathways: “what” pathway, which mimics the ventral pathway of HVS to extract the content features of distorted images, and the “where” pathway, which mimics the dorsal pathway of HVS to extract the global shape features of distorted images. Then, the features from the two pathways are fused and mapped to an image quality score. Additionally, the gradient images weighted by the contrast sensitivity are used as the input to the “where” pathway, allowing it to extract global shape features that are more sensitive to human perception. Moreover, a dual-pathway multi-scale feature fusion module is designed to fuse the multi-scale features of the two pathways, enabling the model to capture both global features and local details, thus improving the overall performance of the model. The experiments conducted on six databases show that the proposed method achieves the state-of-the-art performance.

Typhoon Durian forming over the Western North Pacific Ocean and entering into the South China Sea (SCS), caused extreme and widespread damages in 2006. In this research, sensitivity analyses on different physical parameterization schemes of the Weather Research and Forecasting Atmospheric Model (WRF-ATM) have been utilized to study typhoon Durian. Model accuracy and performance testing were investigated with different initial conditions during the tropical cyclone simulation in the SCS. The initial and boundary conditions (IBCs) for all experiments were derived from the European Centre for Medium Range Weather Forecasts (ECMWF), Re-Analysis Interim (ERAI), and the National Centers for Environmental Prediction (NCEP) with Final (FNL) analysis data compiled through the WRF-ATM model. The sensitivity analysis results indicated a major improvement for the cumulus scheme by using the Grell-Devenyi scheme along with the PBL scheme of Yonsei University, mixed-phase microphysics scheme of the WRF Single Moment 5-class and IBCs for ECMWF-ERAI of TC simulation under the context of Wind-Pressure Relationships. This predicted better track and intensity comparing with these of the Joint Typhoon Warning Center. The results revealed that the TC track and intensity were well simulated by the WSM5-GD combination for the WRF-ATM model with an intensity error of 1.69 hPa for minimum surface level pressure, maximum wind speed of 1.83 knots and average track error of 25 km in 72 hours. The simulations showed that the potential track and intensity error decreased with the delayed IBCs, suggesting that the model simulation is more dependable when the coast is approached by the TC.

This work continues the review and illustrative application to energy systems of the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” (4th-BERRU-PM) methodology. The 4th-BERRU-PM methodology uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, in-cluding fourth (and higher) order sensitivities of computed model responses with respect to model parameters. The 4th-BERRU-PM methodology yields the fourth-order MaxEnt posterior distribution of experimentally measured and computed model responses and parameters, in the combined phase-space of model responses and parameters. The 4th-BERRU-PM methodology encompasses fourth-order sensitivity analysis (SA) and uncertainty quantification (UQ), which were reviewed in the accompanying work (Part 1), as well as fourth-order data assimilation (DA) and model calibration (MC) capabilities, which will be reviewed and illustrated in this work (Part 2). The applicability of the 4th-BERRU-PM methodology to energy systems is illustrated by using the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark, which is modeled using the linear neutron transport Boltzmann equation, involving 21976 im-precisely known parameters. This benchmark is representative of “large-scale computations” such as those involved in the modeling of energy systems. The result (“response”) of interest for the PERP benchmark is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. The impact of the high-order sensitivities of the response with respect to the PERP model parameters is quantified for “high-precision” parameters (2% standard deviations) and “medium-precision” parameters (5% standard deviations). Analyzing the best-estimate results with reduced uncertainties for the 1st- through 4th-order moments (mean values, covariance, skewness, and kurtosis) produced by the 4th-BERRU-PM methodology for the PERP benchmark indicates that, even for systems mod-eled by linear equations (e.g., the PERP benchmark), retaining only first-order sensitivities is insufficient for reliable predictive modeling (including SA, UQ, DA, MC). At least second-order sensitivities should be retained in order to obtain reliable predictions.

Currently, the most promising work seems to be aimed not so much at the development of new drugs, but rather at creating ways of targeted delivery of existing drugs. In this paper, we show that polymeric micelles based on chitosan, heparin grafted with lipoic and oleic acids residues demonstrate the potential for doxorubicin delivery to tumors due to pH-, glutathione-sensitivity. Smart delivery systems use the Aikido principle, i.e. they target tumor cells according to their features. Natural polysaccharides (heparin and chitosan) provide the pH sensitivity of micelles: the release of doxorubicin (Dox) is enhanced in a slightly acidic environment (model tumor microenvironment). Fatty acid residues are necessary for the formation of micelles and solubilization of cytostatics in a hydrophobic core. Lipoic acid residues formed a labile S-S cross-linking between polymer chains (the first method), and also covalently attached doxorubicin molecules through glutathione-sensitive S-S bridges (the second option) – determine Redox sensitivity of micelles to tumors. The characterization of polymeric micelles and prodrugs (Dox-polymer) was carried out using FTIR spectroscopy. The release of doxorubicin from micelles occurs slowly (20% / 6h) in an environment with a pH of 7.4 and the absence of glutathione, while in a slightly acidic environment and in the presence of 10 mM glutathione, the rate increases up 6 times, with an increase in the effective concentration up to 5 times after 7 h. The permeability of free doxorubicin, micellar formulations (covalent S-S crosslinked and not) into Raji, K562, A875 cancer cells was studied using confocal laser scanning microscopy (CLSM), demonstrated an increase in the permeability of micellar formulations based on Dox. Thus, we have presented micellar formulations of doxorubicin for targeted delivery to tumor, what is important in the aspects of reducing non-target toxicity, increasing the selectivity of cytostatics against tumors and overcome multidrug resistance.

In order to study the influence of falling rock shape on its rolling characteristics and realize the optimization of falling rock protection design, the following research was carried out. Design model experiments to explore the rolling characteristics of different shapes of rockfalls. Based on the experimental results, it was found that the slenderness ratio, center of gravity, and rotational inertia of the rockfalls can affect their rolling characteristics, leading to swaying and changing the rolling axis during the rolling process, thereby affecting their rolling speed. On this basis, the formation mechanism of rolling resistance is analyzed, and the main cause of energy loss is the rolling resistance arm formed with the rolling surface during rockfall rolling, and a shape parameter to quantify the rolling resistance is proposed. The parameters are substituted into the kinematic formula, in which the influence of the rockfall shape, slope and slope roughness on the rolling speed is considered. Combined with the offset and initial position of the rockfall, the formula can be used to calculate the rolling speed and impact energy in the rolling region and any position in the region. The calculation formula was validated using model experimental data, and the results showed that the error between the experimental and calculated values was small. The error was corrected based on the experimental data. After on-site testing and verification, it can provide reference for the management of rockfall disasters.

Covid-19 pandemic has greatly affected the whole world since the beginning and it continues to affect it. The main aim of this study is to show how Covid-19 affect other mortal diseases; cancer, heart diseases, and diabetes in near future. With this purpose two mathematical models are proposed via Ordinary Differential Equations (ODEs); one for the relationship between Covid-19 and cancer and one for the relationship between Covid-19, diabetes and heart diseases. Afterwards, stability analyses of these models are demonstrated. In order to see the effect of parameters on the disease compartments, sensitivity analysis is applied. Results of sensitivity analysis revealed that huge percentage of people are still scared of visiting doctors and this may lead a massive increase in the diagnosis of other diseases for upcoming years. Moreover, figures displayed that there exists a relationship between diabetes and heart diseases. Especially, diabetes patients should be careful about their health situations and take care of their heart. In order to provide these, awareness of people should be developed.

Most of the literature on the optimization problem of transportation in supply chain networks (SCN) considered fixed costs (FC). However, in the practical applications of this problem it is important to study the effect of FC. This paper examines the impact of fixed cost increase as well as the variable cost on the optimization of a Two-Stage SCN. To do so, two mathematical models for mixed-integer nonlinear programming are developed. The first model optimizes fixed and variable costs in addition to the opening cost, whereas the second model only optimizes variable and opening costs. To evaluate the effect of considering FC on the optimization supply chain problem, four groups of instances are randomly generated, and solved using Lingo. The results of the two models are compared utilizing the average percentage deviation. In addition, sensitivity analysis is performed to determine the impact of changes in opening and variable costs on the considered optimization problem. The computational results and the sensitivity analysis show that the first model with minimized FC outperforms the second model, which does not consider the FC in minimization and FC affect the optimization.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

Water resource management and flood forecasting are crucial societal and financial stakes requiring reliable predictions of flow parameters (depth, velocity), the accuracy of which is often limited by uncertainties in hydrodynamic numerical models. In this study, we assess the effect of two uncertainty sources, namely breach characteristics induced by overtopping and the roughness coefficient, on water elevations and inundation extent. A two-dimensional (2D) hydraulic solver was applied in a Monte Carlo integration framework to a reach of the Loire river (France) including about 300 physical parameters. Inundation hazard maps for different flood scenarios allowed highlighting the impact of the breach development chronology. A special attention was paid to proposing a relevant sensitivity analysis to exam the factors influencing the depth and extent of flooding. The spatial analysis of vulnerability area induced by a levee breach width exhibits that, with increasing the flood discharge, the rise of the parameter influence is accompanied by a more localized spatial effect. This argues for a local analysis to allow a clear understanding of the flood hazard. The physical interpretation, highlighted by a global sensitivity analysis, showed precisely the dependence of the flood simulation on the main factors studied, i.e. the roughness coefficients and the characteristics of the breaches.

This paper proposes a curved link-slab (CLS) structure, simplified into a hingeless-arch model, to address the current cracking phenomenon of CLS concrete. The stress formula of the hingeless arch under various loads is derived based on the classical mechanic's method. Based on an actual bridge example, the mechanical properties of CLS are analyzed under different loads and load combinations. The results show that: (1) the CLS stress is significantly lower than that of the flat link-slab structure (FLS), (2) its stress values are less than the concrete tensile limit, and (3) the CLS can effectively solve the concrete cracking phenomenon on the link-slab. The rationality of the stress formula derived from the simplified model of the hingeless arch is verified using the finite element method (FEM). The parametric sensitivity analysis shows that variation of the reinforcement ratio of the CLS has a limited impact on it. Considering both the concrete tensile and compressive limit, the thickness of the CLS should be 15 cm to 20 cm, and its design span should be about 5% to7.5% of the main beam length.

The discovery of microRNAs (miRNAs) has fundamentally transformed our understanding of gene regulation. The competing endogenous RNA (ceRNA) hypothesis postulates that not only messenger RNAs but also other RNA transcripts, such as long non-coding RNAs and pseudogenes, can act as natural miRNA sponges. These RNAs influence each other’s expression levels by competing for the same pool of miRNAs through miRNA response elements on their target transcripts, thereby modulating gene expression and protein activity. In recent years, these ceRNA regulatory networks have gained considerable attention in cancer research. Several studies have identified cancer-specific ceRNA networks. Nevertheless, prior bioinformatic analyses have focused on long non-coding RNAs-associated ceRNA networks. Here, we identify an extended-ceRNA network (including both long non-coding RNAs and pseudogenes) shared across a group of four hormone-dependent (HD) cancers, i.e., prostate, breast, colorectal, and endometrial cancers, using data from The Cancer Genome Atlas (TCGA). We performed a functional enrichment analysis for differentially expressed genes in the shared ceRNA network of HD cancers, followed by a survival analysis to determine their prognostic ability. We identified two long non-coding RNAs, nine genes, and seventy-four miRNAs in the shared ceRNA network across four HD cancers. Among them, two genes and forty-one miRNAs were associated with at least one HD cancer survival. This study is the first to investigate pseudogene associated ceRNAs across a group of related cancers and highlights the value of this approach to understanding shared molecular pathogenesis in a group of related diseases.

As fossil-fueled heating in the building sector is responsible for 16 % of Germanys total CO2 emissions, it is of great importance to use climate-neutral alternatives for the decarbonization of this sector. Options for the climate-neutral heating of buildings include electricity or hydrogen as energy carriers, both explicitly considered by German policy. In this paper, bottom-up studies are conducted to investigate the role of hydrogen for the climate-neutral energy supply of ten selected residential buildings in comparison to electricity-based systems. Based on a selection of as different typical buildings as possible for single- (SFH) and multi-family houses (MFH) of different construction years, demand profiles are simulated for each building and the respective cost-optimal supply system is determined. For the construction of this system, the electricity-based technologies available are electric heater and heat pump as well as the hydrogen-based technologies hydrogen boiler and fuel cell combined heat and power (CHP) system. Based on the results of the optimization, sensitivity analyses are performed. These analyses aim to identify threshold values of the hydrogen price for the use of hydrogen in building energy systems as well as to make the quantities of hydrogen consumed visible.The identified threshold values show the significant role of hydrogen-operated CHP in MFH if the hydrogen price reaches 0.17 €/kWh_H2 in 2050 at an electricity price of 0.31 €/kWh_el. So, hydrogen-based energy systems represent an economically viable alternative to electricity-based systems with heat pumps. We identify electricity to hydrogen price ratios for the economically viable use of hydrogen in the examined buildings that range from 1.67 to 2.82. According to these ratios, the economically reasonable use of hydrogen in buildings can be derived. For the individual building groups for the year 2050, a ratio of 2.5 can be determined for SFH and 1.8 for MFH, that is favored by the use of CHP which also supplies electricity to the buildings. However, the role hydrogen will finally play in German residential buildings in the future depends to a large extent on political decisions on distribution issues and price signals.

Background: Flow-through dot-blot assay (FT-DBA) for SARS-CoV-2 specific IgG detection will provide a reliable and affordable immunoassay for the rapid serosurveillance against COVID-19. Method: SARS-CoV-2 antigens were immobilized on nitrocellulose membrane to capture IgG immunoglobulins, which were then detected with AuNP anti-human IgG. A total of 181 samples were characterized with in-house and commercial immunoassay. The positive panel consisted of RT-PCR positive samples from patients with both <14 days and >14 days from the onset of symptoms, while the negative panel contained samples collected either from the pre-pandemic era dengue patients from healthy donors during the pandemic period. Results: In-house ELISA selected a total of 79 true seropositive and 100 seronegative samples. The sensitivity of samples with <14 days using FT-DBA was 94.7% which increased to 100% for samples >14 days. The overall detection sensitivity and specificity were 98.8% and 98%, respectively, whereas the overall PPV and NPV were 97.6% and 99%. Moreover, comparative analysis between ELISA and FT-DBA revealed clinical agreement of Cohen’s Kappa value of 0.944. Conclusion: The assay can confirm past SARS-CoV-2 infection with high accuracy within 2 minutes compared to ELISA. It can help track SARS-CoV-2 disease progression, population screening, and vaccination response.

Global population is predicted to approach 10 billion by 2050, an increase of over 2 billion from today. To meet the demands of growing, geographically and socio-economically diversified nations, we need to diversity and expand agricultural production. This expansion of agricultural productivity will need to occur under increasing biotic, and environmental constraints driven by climate change. Clustered regularly interspaced short palindromic repeats-site directed nucleases (CRISPR-SDN) and similar genome editing technologies will likely be key enablers to meet future agricultural needs. While the application of CRISPR-Cas9 mediated genome editing has led the way, the use of CRISPR-Cas12a is also increasing significantly for genome engineering of plants. The popularity of the CRISPR-Cas12a, the type V (class-II) system, is gaining momentum because of its versatility and simplified features. These include the use of a small guide RNA devoid of trans-activating crispr RNA (tracrRNA), targeting of T-rich regions of the genome where Cas9 is not suitable for use, RNA processing capability facilitating simpler multiplexing, and its ability to generate double strand breaks (DSB) with staggered ends. Many monocot and dicot species have been successfully edited using this Cas12a system and further research is ongoing to improve its efficiency in plants, including improving the temperature stability of the Cas12a enzyme, identifying new variants of Cas12a or synthetically producing Cas12a with flexible PAM sequences. In this review we provide a comparative survey of CRISPR-Cas12a and Cas9, and provide a perspective on applications of CRISPR-Cas12 in agriculture.

Medical insurance claims are becoming increasingly common data sources to answer a variety of questions in biomedical research. Although comprehensive in terms of longitudinal characterization of disease development and progression for a potentially large number of patients, population-based studies using these datasets require thoughtful modification to sample selection and analytic strategies, relative to other types of studies. Along with complex selection bias and missing data issues, claims-based studies are purely observational, which limits effective understanding and characterization of the treatment differences between groups being compared. All these issues contribute to a crisis in reproducibility and replication of comparative findings. This paper offers some practical guidance to the full analytical process, demonstrates methods for estimating causal treatment effects on several types of outcomes common to such studies, such as binary, count, time to event and longitudinally varying repeated measures outcomes, and aims to increase transparency and reproducibility. We provide an online version of the paper with readily implementable code for the entire analysis pipeline to serve as a guided tutorial for practitioners. The online version can be accessed at https://rydaro.github.io/. The analytic pipeline is illustrated using a sub-cohort of patients with advanced prostate cancer from the large Clinformatics TM Data Mart Database (OptumInsight, Eden Prairie, Minnesota), consisting of 73 million distinct private payer insurees from 2001-2016.

This brief note aims to explain the scope in conducting large-scale serological surveys of SARS-CoV-2 to define the landscape of population immunity without overlooking the inherent uncertainty steaming from sampling design and diagnostic validity. The note completes with a succinct statistical appendix of simple methods for estimating prevalence from random population samples using imperfect diagnostic tests.

Hydrologic models are conventionally constrained and evaluated using point measurements of streamflow, which represents an aggregated catchment measure. As a consequence of this single objective focus, model parametrization and model parameter sensitivity are typically not reflecting other aspects of catchment behavior. Specifically for distributed models, the spatial pattern aspect is often overlooked. Our paper examines the utility of multiple performance measures in a spatial sensitivity analysis framework to determine the key parameters governing the spatial variability of predicted actual evapotranspiration (AET). Latin hypercube one-at-a-time (LHS-OAT) sampling strategy with multiple initial parameter sets was applied using the mesoscale hydrologic model (mHM) and a total of 17 model parameters were identified as sensitive. The results indicate different parameter sensitivities for different performance measures focusing on temporal hydrograph dynamics and spatial variability of actual evapotranspiration. While spatial patterns were found to be sensitive to vegetation parameters, streamflow dynamics were sensitive to pedo-transfer function (PTF) parameters. Above all, our results show that behavioral model definition based only on streamflow metrics in the generalized likelihood uncertainty estimation (GLUE) type methods require reformulation by incorporating spatial patterns into the definition of threshold values to reveal robust hydrologic behavior in the analysis.

While nursing is an ethical profession, unethical behavior among nurses is increasing worldwide. This study examined the effects of an ethics seminar on nurses' moral sensitivity and ethical behavior. A total of 37 nurses (17 experimental, 20 control) were recruited. The ethics seminar was held over a 6-month period from May to October, 2018, and comprised six sessions held once a month for two hours. Moral sensitivity and unethical behavior were measured at the start and end of the seminar. Moral sensitivity and unethical behavior showed a negative correlation (r= -.455, p&lt;0.01). After the ethics seminar, the experimental group's moral sensitivity was significantly increased (t = -1.039, p = 0.314). The mean scores of unethical behavior at pre and post-test in the experimental group were 12.59 and 9.47, respectively. This was a statistically significant difference (t = 3.118, p = 0.004). There was no statistically significant difference in the mean score in both moral sensitivity and unethical behavior in the control group. We conclude that ethics seminars can enhance moral sensitivity and reduce the risk of unethical behavior among nurses. Regular ethics seminars and training must be provided to nurses as a matter of policy.

This review article explores the convergence of virtual reality (VR) and architectural design from an inclusive lens. It underscores the crucial role of virtual reality (VR) in serving as a catalyst for the incorporation of social and cultural sustainability principles in architectural projects. The exploration is guided by inclusive design principles, which encompass several aspects such as accessibility, cultural sensitivity, diversity and inclusivity, user-centered design, and empathy. These concepts serve as the basis for further investigation into the potential of virtual reality (VR) technology to enhance and heighten these features within architectural design, therefore promoting the progress of social and cultural sustainability. The review article highlights the profound impact that virtual reality (VR) may have, going beyond mere visualisation to generate architectural experiences that are immersive, interactive, and empathetic. These experiences are designed to take into account diverse perspectives and needs.

Flow and transport processes in soil and rock play a critical role in agricultural non-point source pollution (ANSP) loads. In this study, we investigated the ANPS load discharged into rivers from an irrigation district in the Tibetan Plateau, and simulated ANPS load using a distributed model involving detailed descriptions of flow and ANPS transport and transformation processes in the soil and rock. Experiments were conducted for two years to measure soil water content and nitrogen concentrations and the quality and quantity of lateral flow in the rock and at the drainage canal outlet during the highland barley growing period. A distributed model, in which the subsurface lateral flow was described using a step-wise method, was developed to simulate flow and ammonium nitrogen and nitrate nitrogen transport. Sobol’s method was used to evaluate the sensitivity of simulated flow and transport processes to model inputs. The results showed that, with a 21.2% increase of rainfall and irrigation in the highland barley growing period, the average NH4+-N and NO3--N concentrations in the soil layer decreased by 10.8% and 14.3%, respectively, due to increased deep seepage. Deep seepage of rainfall water accounted for 0–52.4% of total rainfall, whereas deep seepage of irrigation water accounted for 36.6–45.3% of total irrigation. NH4+-N and NO3--N discharged into the drainage channel represented 19.9–30.4% and 19.4–26.7% of the deep seepage, respectively. The mean Nash-Sutcliffe coefficients, root mean square errors, and cumulative deviations between the measured and simulated flow rates and NH4+-N and NO3--N concentrations at the surface drainage canal outlet were 0.694, 0.081, and 0.242, respectively, indicating that the proposed method can effectively describe the hydrological and ANPS pollution migration in the plateau irrigation zone. The Sobol’ sensitivity analysis results demonstrated that subsurface lateral flow had the most important first order and total effect on the simulated flow and NH4+-N and NO3--N concentrations at the surface drainage outlet.

Background: Systemic lupus erythematosus (SLE) is characterized by inflammation and cardiovascular complications. Our study aimed to investigate subclinical and early indicators of systolic myocardial dysfunction in SLE patients using advanced echocardiographic methods and biomarkers. Methods: In this cross-sectional study, we enrolled 102 SLE patients without known cardiac impairment and 51 healthy controls. Demographics, disease characteristics, laboratory results, disease activity (SLEDAI) and organ damage (SDI) indices were recorded. Left ventricular global longitudinal strain (GLS) and myocardial work indices were assessed by utilizing speckle tracking echocardiography. In addition, high sensitivity C-reactive protein (hsCRP), high sensitivity troponin (hsTn) and N-terminal-pro B-type natriuretic peptide (NT-proBNP) levels were measured in blood samples. Results: In comparison to controls, SLE patients had significantly higher GLS (-19.94±2.71%vs-21.15±1.55%, p&lt;0.001) and global wasted work (GWW) (94±71mmHg%vs71±49 mmHg%, p=0.025). Notably, NT-proBNP and hsTn were threefold and twofold higher in SLE group compared to control group, respectively (p&lt;0.001). Within SLE cohort, patients with at least moderate disease activity (SLEDAI≥4) both biomarkers were significantly elevated than those with low disease activity (SLEDAI&lt;4). Conclusion: Advanced echocardiographic parameters combined with specific biomarkers have a promising role in detecting systolic dysfunction at an early phase in SLE patients, potentially enabling timely interventions to mitigate cardiovascular risk.

The subtropical forest soil plays a pivotal role in terrestrial carbon (C) cycling. Although global warming is expected to influence subtropical soil C cycling, a consensus on its impact on soil C dynamics remains elusive. Given the significant response of soil microbial respiration to temperature in subtropical soils, understanding its behavior under varying temperature regimes is critical for predicting soil organic C (SOC) responses to climate warming. We conducted a short-term laboratory soil warming incubation experiment, sampling both warmed and un-warmed soils from a subtropical plantation in southeastern China, incubating them at 20 °C, 30 °C, and 40 °C. Our aim was to study the SOC mineralization response to increasing temperatures. Our findings revealed that the temperature sensitivity (Q10) of SOC mineralization to short-term experimental warming varied between the warmed soil and the un-warmed soil. The Q10 of the un-warmed soil escalated with the temperature treatment (20-30 ℃: 1.31, 30-40℃: 1.63). Conversely, the Q10 of the warmed soil decreased (20-30 ℃:1.57, 30-40 ℃:1.41). Increasing temperature treatments enhanced hydrolytic enzyme activity but decreased soil substrate availability in both un-warmed and warmed soil. The Q10 of un-warmed soil was positively correlated with the response ratio of DOC. Additionally, soil microbial biomass exhibited a significant decline, leading to a reduced total amount of PLFAs and a decreased abundance of bacteria, fungi, and Gram-negative bacteria (GN). The changes in temperature also considerably altered the composition of the warmed soil microbial community. A drop in the microbial quotient coupled with a rise in the metabolic quotient indicated that warming amplified microbial respiration over microbial growth. The differential Q10 of SOC mineralization, in response to temperature across varying soil, can largely be attributed to shifts in soil nutrients, C-degrading enzyme activities, and microbial communities (the ratio of fungal to bacterial PLFAs).

Leucine-rich α-2 glycoprotein1 (LRG1) is a member of the leucine-rich repeat (LRR) family that was implicated in multiple diseases including cancer, aging and heart failure as well as diabetes and obesity. LRG1 plays a key role in diet-induced hepatosteatosis and insulin resistance by mediating the crosstalk between adipocytes and hepatocytes. LRG1 also promotes hepatosteatosis by upregulating de novo lipogenesis in the liver and suppressing fatty acid β oxidation. In this study, we investigated the association of LRG1 with obesity markers including leptin and other adipokines in adolescents (11-14 years; n=425). BMI-for-age classification based on WHO growth charts was used to define obesity. Plasma LRG1 was measured by ELISA while other markers were measured by multiplexing assay. Median (IQR) of LRG1 levels was higher in obese [30 (25, 38) µg/mL] and overweight [30 (24, 39) µg/mL] adolescents, compared to normal-weight participants [27 (22, 35) µg/mL]. The highest tertile of LRG1 had an OR [95%CI] of 2.55 [1.44, 4.53] for obesity. LRG1 was positively correlated to plasma levels of HsCRP (R=0.2), Leptin (R=0.2) and Chemerin (R=0.24) with p<0.001. Additionally, it was positively associated with plasma level of IL6 (R=0.17) and IL10 (R=0.14) but not TNF-α. In conclusion, LRG1 levels are increased in obese kids and associate with increased levels of adipogenic markers. These results suggest the usefulness of LRG1 as an early biomarker for obesity and its related pathologies in adolescents.

(1) Background: The emergence of antibiotic-resistant bacteria is a growing concern in the field of medicine. This has led to the need for alternative treatments for bacterial infections. (2) Methods: The present study aimed to investigate the synergistic effect of a water-based extract of S. fru-tescens and penicillin G on the growth of E. faecalis. (3) Results: The study found that the combina-tion of the plant extract and penicillin G had a synergistic effect on the inhibition of bacterial growth, with a significantly larger inhibition zone observed compared to penicillin G alone. The MIC and MBC tests also demonstrated that the combination of the plant extract and penicillin G was more effective against E. faecalis than penicillin G alone, with a dilution of 1 in 4 yielding 100% inhibition of growth. (4) Conclusion: Although the specific mechanism of action was not dis-cussed in the study, the results suggest that the combination of the plant extract and penicillin G may offer a promising alternative treatment for antibiotic-resistant infections. Further research is needed to determine the active compounds in the plant extract and to investigate the synergistic effect of the combination on other strains of bacteria.

Early stroke diagnosis remains a big challenge in healthcare partly due to the lack of reliable diagnostic blood biomarkers, which in turn leads to increased rates of mortality and disability. Current screening methods are optimised to identify patients with a high risk of cardio-vascular disease, especially among the elderly. However, in young adults and children, these methods suffer low sensitivity and specificity and contribute to further delays in their triage and diagnosis. Accordingly, there is an urgent need to develop reliable blood biomarkers for triaging patients suspected of stroke in all age groups, especially children and young adults. This review explores some of the existing blood biomarkers, as single biomarkers, or biomarker panels, and examine their sensitivity and specificity for predicting stroke. A review was performed on PubMed and Web of Science for journal articles published in English during the period 2001 to 2021 which contained information regarding biomarkers of stroke. In this review article, we provide comparative information on the availability, clinical usefulness, and time-window periods of eight single blood biomarkers and six biomarker panels that have been used for predicting stroke in emergency situations. The outcomes of this review can be used in future research for developing more effective stroke biomarkers.

This study presents the complexity and sensitivity of chaotic system dynamics in the case of the double pendulum. It applied detailed numerical analyses of the double pendulum in multiple computing platforms in order to demonstrate the complexity in behavior of the system of double pendulums. The equations of motion were derived from the Euler-Lagrange formalism, in order to capture the system's dynamics, which is coupled nonlinearly. These were solved numerically using the efficient Runge-Kutta-Fehlberg method, implemented in Python, R, GNU Octave, and Julia, while runtimes and memory usage were extensively benchmarked across these environments. Time series analyses, including the calculation of Shannon entropy and the Kolmogorov-Smirnov test, quantified the system's unpredictability and sensitivity to infinitesimal perturbations of the initial conditions. Phase space diagrams illustrated the intricate trajectories and strange attractors, as further confirmation of the chaotic nature of the double pendulum. All the findings have a clear indication of the importance of accurate measurements of the initial condition in a chaotic system, contributing to an increased understanding of nonlinear dynamics. Future research directions are faster simulations using Numba and GPU computing, stochastic effects, chaotic synchronization, and applications in climate modeling. This work will be useful for understanding chaos theory and efficient computational approaches in complex systems of dynamical nature.

In Tropical Monsoon climates, precipitation exceeds evapotranspiration, leading to increased surface runoff, especially in floodplain regions. The Bhagirathi-Hooghly River in India is the focus of the study, which analyses hydrology, sediment yield, and water balance in this floodplain area. This investigation employs the Soil and Water Assessment Tool (SWAT) model within the ArcGIS environment, using remote sensing data. The study area is divided into 4 sub-basins and 40 Hydrological Response Units (HRUs), with a focus on Land Use/Land Cover (LULC) parameters, soil attributes, and slope characteristics. Calibration (1998-2010) and validation (2011-2018) of river discharge and sediment yield are performed using the SUFI-2 algorithm within SWAT-CUP. The calibration process shows a strong correlation between observed and simulated data points, indicating the model's accuracy. The study reveals a pattern of early-year evapotranspiration followed by increasing rainfall during the monsoon season, leading to heightened surface runoff and sediment yield. Excessive rainfall, therefore, emerges as a pivotal driver of flood incidences within the floodplain. The insights derived from the SWAT model's floodplain data have the potential to inform flood control and sedimentation mitigation strategies. The assimilation of this data can empower local stakeholders and contribute to sustainable livelihoods and improved living conditions, offering guidance for future governmental policies.

The type III receptor tyrosine kinase FLT3 is a pivotal kinase for hematopoietic progenitor cell regulation, with significant implications in acute myeloid leukemia (AML) through mutations like internal tandem duplication (ITD). This study delves into the structural intricacies of FLT3, the roles of activation loop mutants, and their interaction with tyrosine kinase inhibitors. Coupled with this, the research leverages molecular contrastive learning and protein language modeling to examine interactions between small molecule inhibitors and FLT3 activation loop mutants. Utilizing the ConPLex platform, over 5.7 million unique FLT3 activation loop mutants-small molecule pairs were analyzed. The binding free energies of three inhibitors were assessed, and cellular apoptotic responses were evaluated under drug treatments. Notably, the introduction of the Xepto50 scoring system provides a nuanced metric for drug efficacy. The findings underscore the modulation of molecular interactions and cellular responses by Y842 mutations in FLT3-KD, highlighting the need for tailored therapeutic approaches in FLT3-ITD-related malignancies.

This study aims to theoretically address the design and analysis of an efficient pressure sensor designed by using a polymer-based defective 1D annular photonic crystal (APC). The 1D APC comprises an alternate arrangement of Si and SiO2 in a cylindrical fashion, incorporating a central defect layer. The investigation of the reflectance characteristics of the proposed structure is conducted by separately considering the polystyrene (PS) and the polymethyl methacrylate (PMMA) polymer materials as the defect layer. The pressure-sensitive refractive index of the polymers and the constituent materials of the APC plays a vital role in envisaging the pressure-sensing application. The cornerstone of this study is represented by the shift analysis in the wavelength of the defect mode inside the band gap using different applied pressures by employing the modified transfer matrix method (MTMM). Various geometrical parameters like the defect polymer layer’s thickness and the APC period were carefully optimized to achieve higher sensing performance. The proposed design demonstrated a remarkable pressure sensitivity and FoM of 51.29 nm/GPa and 301.7 GPa-1, respectively, which is considerably high in the current research scenario. It is believed that the proposed structure can be an apt candidate as an innovative high-performance pressure sensor, and it can play a key role in photonic integrated circuits.

In order to study the surface settlement law of subway tunnel engineering site overlying soft soil layer under the action of earthquake, ABAQUS finite element analysis software was used to study the surface settlement law of subway tunnel construction site overlying soft soil layer under the action of three different seismic waves, including El-Centro wave, Kobe wave, and artificial seismic wave with exceedance probability of 10%, based on the Dalian Metro Line 5 with overlying soft soil layer as the engineering background, and the law was analyzed theoretically. Then, the surface settlement law of tunnel top was studied based on El-Centro wave and soft soil parameters, and the sensitivity analysis of soft soil parameters on surface settlement of tunnel top was carried out by orthogonal test method. The results show that under earthquake action, the settlement of the strata within a certain range of the tunnel roof is significantly greater than that of the surrounding strata, forming a settlement trough with a width of about 8 to 20 meters. The width of the settlement trough under the El-Centro wave is the largest, about 19.6 meters, surpassing the artificially synthesized seismic waves with a probability of 10%, which is about 15.6 meters, while the width of the settlement trough under the Kobe wave is the smallest, about 8.5 meters. The ground surface within a range of about 20 meters above the tunnel roof is most strongly affected by the seismic waves and the special lithology of the overlying soft soil layer, and the settlement is the largest. The settlement law of the settlement trough in the overlying strata of the tunnel conforms to the Peck formula. Increasing the elastic modulus of the silty soil can reduce the settlement of the ground surface above the tunnel roof, increasing the Poisson's ratio of the silty soil will increase the settlement of the ground surface above the tunnel roof, increasing the cohesive force of the silty soil to 20 kPa will basically stabilize the settlement of the ground surface above the tunnel roof, and increasing the internal friction angle of the silty soil will basically not change the settlement of the ground surface above the tunnel roof. The sensitivity of the soft soil parameters to the settlement of the ground surface above the tunnel roof is in the order of Poisson's ratio, elastic modulus, cohesive force, and internal friction angle.

Musculoskeletal models (MSKMs) are used to estimate the muscle and joint forces involved in human locomotion, often associated with the onset of degenerative musculoskeletal pathologies (e.g. osteoarthritis). Subject-specific MSKMs offer more accurate predictions than their scaled-generic counterparts. This accuracy is achieved through time-consuming personalisation of models and manual tuning procedures that suffers from potential repeatability errors, hence limiting the wider application of this modelling approach. In this work we have developed a methodology for identifying and ranking the muscles that are more important to the determination of the joint forces, thus producing reduced but still accurate representation of the musculoskeletal system in shorter timeframes. The methodology hinges on Sobol's sensitivity analysis (SSA) for ranking the muscle importance. The thousands of data points required for SSA are generated using Gaussian Process emulators, a Bayesian technique to infer the input-output relationship between nonlinear models from a limited number of observations. Results show that there is a pool of muscles whose personalisation has little effects on the model predictions. Furthermore, joint forces in subject generic and subject generic models are influenced by different set of muscles, suggesting the existence of a model specific component of the sensitivity analysis.

Predicting the tidal wave is essential not only to better understand hydrological cycle at the boundary between land and ocean but also to improve energy production in the coastal area. As affected by various factors such as astronomical, meteorological, and hydrological effects, predicting the tidal wave at the estuary remains uncertain. In this study, we present a novel method to improve short-term tidal wave predictions using a fixed-lag smoother based on sequential data assimilation (DA). The proposed method is implemented for the tidal wave predictions at the estuary of Nakdong River. As a result, the prediction accuracy was improved by 63.9% with DA and the calibration using the regression. Although the accuracy of DA diminished for increasing forecast lead times, the 1-hr lead forecast by DA had still 44.4% improvement over the open loop without DA. Plus, the optimal conditions for the fixed-lag smoother were analyzed in terms of the order of a smoothing function and the length of assimilation window and forecast lead time. It was suggested that the optimal DA configuration could be obtained with the 8th order polynomial as a smoothing function assimilated under 6-hr or longer past and future DA windows.

The combination of statistical learning technologies with large databases of psychophysiological data has appropriately generated enthusiastic interest in future clinical applicability. It is argued here that this enthusiasm should be tempered with the understanding that significant obstacles must be overcome before the systematic introduction of psychophysiological measures into neuropsychiatric practice becomes possible. The nonspecificity of psychophysiological measures complicates their use in diagnosis. Low test-retest reliability complicates use in longitudinal assessment, and quantitative psychophysiological measures can normalize in response to placebo intervention. Ten cautionary observations are introduced and, in some instances, possible directions for remediation are suggested.

Trachsummaroma is an eye infectious disease caused by Chlamydia Trachomatis bacterium, which may lead to irreversible blindness. The disease is spread directly or indirectly by contacting a contaminated material. It can also be transmitted through the disease vector known as “Musca sorbens” or “Bazaar fly”. To curtail the spread of the disease in a population, a meaningful information on the spread and possible control of the disease is required. Mathematical modeling provides efficient tools that can be used to understand and analyze the dynamics of the disease and its control. Several compartmental epidemic models have been proposed in the literature to study the dynamics of trachoma; including SI, SIR and SEIR. However, majority of the existing trachoma models consider only person to person transmission. Thus, the information provided by such models is insufficient since they did not capture the disease vector transmission. The current study proposed a novel SEIR-SEI model that consider both person-person and vector transmission dynamics. The threshold quantity, basic reproduction number R0 is obtained using the next generation matrix, and it was proved that the disease-free equilibrium is asymptotically stable when R0 < 1, and the endemic equilibrium is globally asymptotically stable when R0 > 1. Some simulation results with the aid of mesh plots for the reproductive number as a function of two different biological parameters were obtained. Furthermore, a comprehensive sensitivity analysis is conducted to identify the influence of the individual parameters on the R0. Numerical results show that the vector contact rate has the highest sensitivity with respect to R0, and the value of R0 increases with increase in, hence, the disease can be controlled by decreasing the vector contact rate. Similarly, improving the rate of environmental hygiene and facial cleanliness will decrease the size of R0 and result in the declination of the disease transmission. Moreover, a detailed parameter estimation of the model parameters and model fitting was presented with the use of field data cases from Northern Nigeria using least-square fitting method. The study provides alternative tools that can be used for planning trachoma control program to achieve global eradication of trachoma as a public heath challenge as targeted by WHO in 2030.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

Recently, light traps using light-emitting diode (LED) lights have been applied to monitor or control insect pests. The oriental armyworm, Mythimna separata Walker, is an important insect pest that has caused damage to several cereal crops, including corn, wheat and rice. The present study aims to seek out a sensitive wavelength causing high phototactic response in M. separata. The study evaluated the phototactic responses of M. separata moths to several LED lights of different wavelengths and luminance intensities under laboratory condition. Results showed that green (520 nm) LED light resulted in significant phototactic response of M. separata moths compared to LED lights of other wavelengths. Additionally, the highest attraction rate of the moths to green LED light appeared in luminance intensity group of 200 lux compared to the other intensities groups. Experiments under optimum conditions based on the above experiments revealed that the green LED light exhibited the strongest attraction rate (64.44%) among all experimental groups. An experiment performed in a net cage also showed that green LED light resulted in the highest phototactic response of M. separata moths, 1.7 times more than a commercial black light used as control. These findings clearly demonstrate that M. separata moths have a high sensitivity to the green LED light. Therefore, a light trap equipped with green LED light could be useful for monitoring and controlling M. separata moths.

Finite element (FE) modeling is commonly used as a method to investigate the influence of medical devices, such as implants and screws and their effects on the biomechanical behavior of the spine. Another simulation method is a multi-body simulation (MBS), where the model is composed of several non-deformable bodies. MBS solvers generally require a very short computing time for dynamic tasks compared to an FE analysis. Considering this computational advantage, in this study, we examine whether parameters whose values are not known a priory can be determined with sufficient accuracy using MBS model. Therefore, we propose a Many-at-a-time sensitivity analysis method that allows approximating these a priory unknown parameters without requiring long simulation times. This method enables a high degree of MBS model optimization to be achieved in an iterative process. The sensitivity analysis method is applied to a simplified screw-vertebra model, consisting of an anterior anchor implant screw and vertebral body of C4. An experiment described in the literature is used as a basis for developing and assessing the potential of the method for sensitivity analysis and to validate the models action. The optimal model parameters for the MBS model were determined to be c=823224N/m for stiffness and d=488Ns/m for damping. The presented method of parameter identification can be used in studies including more complex MBS spine models or to set initial parameter values that are not available as initial values for FE models.

Densimetric Froude (Fr) is the minimum velocity required to prevent sediment deposition in pipes. Prediction of Fr is of utmost importance in numerous applications in civil engineering. In this paper through using a new hybrid method. Genetic Algorithm (GA) is used for optimum selection of membership functions of Adaptive Neuro-Fuzzy Inference System (ANFIS), and Singular Value Decomposition (SVD) method is used to compute the linear parameters of ANFIS’s results section (ANFIS-GA/SVD). Also, two different target functions are known as training error (TE) and prediction error (PE) by Pareto curve, the trade-off between these functions is selected as the optimal modeling point. First, different models will be presented using the parameters affecting Fr prediction, classifying them in different groups; then the Fr parameter will be predicted for all the different models through utilizing three different sets of data and the ANFIS-GA/SVD technique. The results of the models indicate that the best Fr prediction is obtained when independent parameters such as volumetric sediment concentration (CV), ratio of median diameter of particle size to pipe diameter (d/D), ratio of median diameter of particle size to hydraulic radius (d/R) and overall friction factor of sediment (λs) use as input variables in prediction of Fr. A sensitivity analysis is also conducted for the purpose of examining the effect of each of the dimensionless parameters on Fr prediction accuracy. Comparing the results of the suggested models with the existing regression-based equations shows that ANFIS-GA/SVD (R²=0.986, MAPE=4.397, RMSE=0.206, SI=0.053, ρ=0.026, BIAS=-0.025) is more accurate than the rest of the models.

The inaccurate estimates of linear prediction coefficient (LPC) and noise variance introduce bias in Kalman filter (KF) gain and degrades speech enhancement performance. The existing methods proposed a tuning of the biased Kalman gain particularly in stationary noise condition. This paper introduces a tuning of the KF gain for speech enhancement in real-life noise conditions. First, we estimate noise from each noisy speech frame using a speech presence probability (SPP) method to compute the noise variance. Then construct a whitening filter (with its coefficients computed from the estimated noise) and employed to the noisy speech, yielding a pre-whitened speech, from where the speech LPC parameters are computed. Then construct KF with the estimated parameters, where the robustness metric offsets the bias in Kalman gain during speech absence to that of the sensitivity metric during speech presence to achieve better noise reduction. Where the noise variance and the speech model parameters are adopted as a speech activity detector. The reduced-biased Kalman gain enables the KF to minimize the noise effect significantly, yielding the enhanced speech. Objective and subjective scores on NOIZEUS corpus demonstrates that the enhanced speech produced by the proposed method exhibits higher quality and intelligibility than some benchmark methods.

We presented a fractional order model to capture the transmission dynamics of Anthrax infection with a nonlinear force of infection and its long-term impacts. Analysis by the standard Fabrizio Caputo approach established the model is well-posed and investigation on the stability of the model, Anthrax-free equilibrium as connected to the basic reproduction number R0

Zambia recently experienced extended hours of load shedding due to reduced hydroelectricity generation attributed to poor rainfall patterns. The inability to meet energy demand has influenced the government to consider alternative energy sources. This study aims to assess the economic feasibility of the eight sites using a 25-turbine layout for a 4 MW generic wind turbine at 130m hub height. An economic evaluation mathematical model was developed to analyze the economic feasibility using net present value, simple payback period, internal rate of return, and levelized cost of electricity (LCOE). The study shows that the Lusaka wind farm was the most economical with 386 GWh energy yield analysis (EYA), wind speed of 8 m/s, NPV of 316 million dollars, SPP of 2.9 years, IRR of 82%, and LCOE of $0.182/ kWh. The results also show that the other seven sites are economically feasible, with Petauke being the lowest. The study's economic sensitivity analysis conducted by varying the average electricity tariff shows that Lusaka was the most financially viable site. Therefore, policymakers should develop cost-reflective feed-in tariff (FiT) schemes and power purchase agreements for the country to have cost-reflective electricity tariffs that will motivate independent power producers to invest in Zambia.

Flood inundation causes socioeconomic losses for coastal tourism under climate extremes, progressively attracting global attention. Mapping, evaluating, and predicting the flood inundation risk (FIR) is significant for coastal tourism. The study develops a spatial tourism–aimed framework integrating a weighted k-Nearest Neighbors (WkNN), Geographic Information Systems, and flood-related spatially environmental criteria such as precipitation, elevation, soil, and drainage systems. These model inputs were standardized and weighted using distance, and integrated into WkNN to infer regional probability and distribution of FIR. Zhejiang province, China, was selected as a case study. The resulting map was pictured to denote the likelihood of the criteria at various risk categories, which was validated by historical Maximum Inundation Extent (MIE) extracted from World Environment Situation Room. The result indicates 80.59% of WkNN results reasonably confirm the MIE. Precipitation and elevation make a negative contribution to high-medium risk, and drainage systems positively alleviate the regional stress of FIR. The results can help stakeholders make suitable strategies to protect coastal tourism, and also weigh WkNN is superior to kNN in FIR assessment. The framework provides a productive way to yield a reliable assessment of FIR and can also be extended to other risk-related environmental studies under climate change.

Research background – In the conditions of a modern developed market economy, a rather important characteristic of the activities of a public company is its activity in the stock market (market activity), which involves the development of a dividend policy, which, on the one hand, should contribute to the achievement of the main goal of financial management - maximizing the material well-being of shareholders, and, on the other hand, take into account the interests of all other stakeholders interested in the activities of a public company (including potential investors) to ensure its sustainable development in the long term. Fulfillment of this requirement is possible only within the framework of a neutral approach to the implementation of the dividend policy of a public company.Purpose – The article is devoted to the consideration of the conceptual foundations for analyzing the sensitivity of key indicators of the activity of a public company in the stock market (market activity) to the main determining factors in the context of a neutral approach to the implementation of its dividend policy.Design/methodology/approach – The methodological basis of the study was the concept of a neutral approach to the dividend policy of a public company and the concept of sensitivity analysis, developed earlier by the author of this article.Findings – It is shown that the key indicators of the market activity of a public company include the dividend yield ratio, dividend coverage ratio, the expected price of an ordinary share, the dividend yield of an ordinary share and the quote ratio of an ordinary share (price and earnings ratio per ordinary share). An analysis of the sensitivity of these indicators to the main determining factors in the context of a neutral approach to the implementation of the dividend policy of a public company involves the construction of appropriate elasticity models that allow determining the change in key indicators of market activity depending on changes in the factors that determine them. The constructed elasticity models of the key indicators of market activity listed above can be used in predictive and analytical assessments of their changes, and also make it possible to identify the causes of these changes by calculating the impact on the specified elasticity of the determinants contained in their models, performed by the appropriate methods of factor analysis, under the conditions of a neutral approach to the implementation of the dividend policy of a public company.Originality/value – The author comes to the conclusion that the elasticity models developed by him for key indicators of the activity of a public company in the stock market in terms of the main factors determining them are a fairly effective tool for managing the market activity of a public company in the context of a neutral approach to the implementation of its dividend policy.

Metformin, the treatment of first choice in type 2 diabetes (T2D), is known to mainly act by decreasing endogenous glucose production (EGP) in the liver. Paradoxically, in the last decade several reports documented increased EGP after metformin treatment. This increase, was often attributed to pronounced rises in glucagon, consistent with counter-regulatory response to the glucose lowering effect of metformin. However, considering that hyperglucagonemia, but not hypoinsulinemia, is a main driver of EGP in T2D, increased EGP should have been a common finding. This observation, together with the finding that metformin antagonizes glucagon effects on energy expenditure and protein synthesis, concurrently to its effects on EGP and the emerging evidences demonstrating increased branched chain and gluconeogenic amino acids in response to metformin treatment may points to a liver alpha-cell skeletal muscle cross talk similar to that observed in the liver-alpha cell axis. Here, we provide a mechanistic perspective to this latter possibility, based on mechanistic studies of metformin’s transcriptional targets; retaining thus its glucagon antagonistic and presumably anti-gluconeogenic effects on liver and attributing the increase in EGP to renal gluconeogenesis. We finally discuss how increased EGP might reflect an adverse response to metformin treatment, providing support from clinical and epidemiological data.

The characteristics of the eddy mass transport are estimated depending on the values of the parameters of a large-scale flow that forms under the conditions of the shelf seas in the Arctic. For this, the results of numerical simulation of the Kara Sea with a horizontal resolution permitting the development of mesoscale eddies are used. The parameters resulting from numerical experiment are considered as a statistical sample and are analyzed using methods of sensitivity study and clustering of sample elements. Functional dependencies are obtained that are closest to the simulated distributions of quantities. These expressions make it possible, within the framework of large-scale models, to evaluate the characteristics of the cross-isobatic eddy mass transport in the diffusion approximation with a counter-gradient flux. Numerical experiments using the SibCIOM model showed that areas along the Fram branch of the Atlantic waters trajectory in the Arctic as well as the shelf of the East Siberian and Laptev seas with adjacent deep water areas are most sensitive to proposed parameterization of eddy exchanges. Accounting for counter-gradient eddy fluxes turned out to be less important.

The effects of transcranial magnetic stimulations (TMS) show that the human brain is impacted by some magnetic fields (EMFs). Moreover, after a delay, it produces potentials that reveal a subsequent processing of this impact. The human brain might also be sensitive to very weak magnetic fields of extremely low frequencies (vwEMFelf). Namely, to the vwEMelf produced by the brain of other persons when they process visual stimuli. In effect, two studies report that the event-related brain potentials (ERPs) that are evoked by presenting a picture to a participant can be modulated by simultaneously presenting a picture to a partner. To confirm it here, we followed most of the methods of these studies. We recorded the ERPs evoked by presenting, at each trial, the photograph of a face. Simultaneously and, most importantly, privately, we presented a partner with the same or with a different face photograph. ERPs of participants were found to depend on that sameness (p0.001), unbeknownst to them. These joint processing effects (JPEs), confirm a sensitivity of the human brain to the vwEMFelf produced by other brains.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

In this paper, a solenoid based linearly movable armature system is designed using robust control theory in order to improve the performance of the system. Reference track method is the best performance analysis for position control systems. Among the robust controllers, H infinity mixed-sensitivity and Mixed H 2 /H∞ with Regional Pole Placement Controllers are used to improve the performance of the system. Comparison of the proposed controllers for tracking a reference displacement signals (step and sine wave) and a promising simulation result have been obtained.

The present novel corona virus (2019-nCoV) infection has created a global emergency situation by spreading all over the world in a large scale within very short time period. The infection induced death rate is also very high. There is no vaccine or anti-viral medicine for such infection. So at this moment a major worldwide problem is that how we can control this pandemic. On the other hand, India is a high population density country, where the corona virus disease (COVID-19) has started to spread from $1^{st}$ week of March, 2020 in a significant number of COVID-19 positive cases. Due to this high population density human to human social contact rate is very high in India. So control of the pandemic COVID-19 in early stage is very urgent and challenging problem. Mathematical models are employed in this paper to study the COVID-19 dynamics, to identify the influential parameters and to find the proper prevention strategies to reduce the outbreak size. In this work, we have formulated a deterministic compartmental model to study the spreading of COVID-19 and estimated the model parameters by fitting the model with reported data of ongoing pandemic in India. Sensitivity analysis has been done to identify the key model parameters. The basic reproduction number has been estimated from actual data and the effective basic reproduction number has been studied on the basis of reported cases. Some effective preventive measures and their impacts on the disease dynamics have also been studied. Future trends of the disease transmission has been Predicted from our model with some control measures. Finally, the positive measures to control the disease have been summarized.

The effect of sensitivity points (sequence order and position of every element) of sequences following comparative optinalysis under two proposed mechanisms, the paranodic and synodic skewization, was studied to develop a modeling approach to comparative optinalysis of sequences. The results show that the outcomes of comparative optinalysis (similarity measurement) in a set of paranodically skewed sequences can be modeled deterministically by suitable line regression functions. The sensitivity points (nodes) of a sequence display two important and distinct zones, the K-zones and the B-zones. Continues paranodic skewization within these zones (KB zones) operates within probability space, but at hyperskewization level and at the K-zones only, the outcomes of comparative optinalysis operate outside the probability space. Moreover, the outcomes of comparative optinalysis by synodic skewization can be modeled deterministically by some regression line functions, but a general regression function cannot be identified. At certain limit of skewization value space, following paranodic and synodic skewization, the outcomes of comparative optinalysis at the left-sided sequence form a similar pattern with the right-sided sequence.

The cardioprotective effects of volatile anesthetics versus total intravenous anesthesia (TIVA) are controversial, especially in patients undergoing non-cardiac surgery. Using current generation high-sensitivity cardiac troponin (hs-cTn), we aimed to evaluate the effect of anesthetics on the occurrence of myocardial injury after non-cardiac surgery (MINS). From February 2010 to December 2016, 3555 patients without preoperative hs-cTn elevation underwent non-cardiac surgery under general anesthesia. Patients were grouped according to anesthetic agent; 659 patients were classified into a propofol-remifentanil total intravenous anesthesia (TIVA) group, and 2896 patients were classified into into a volatile group. To balance the use of remifentanil between groups, a balanced group (n=1622) was generated with patients who received remifentanil infusion in the volatile group, and two separate comparisons were performed (TIVA vs. volatile and TIVA vs. balanced). The primary outcome was occurrence of MINS, defined as rise of hs-cTn I ≥ 0.04 ng/mL within postoperative 48 hours. The secondary outcomes were 30-day mortality, postoperative acute kidney injury (AKI), and adverse events during hospital stay (mortality, type I myocardial infarction (MI), and new-onset arrhythmia). In propensity-matched analyses, the occurrence of MINS was lower in the TIVA group compared to the volatile group (OR 0.642; 95% CI 0.450-0.914; p = 0.014). However, after balancing the use of remifentanil, there was no difference between groups in the risk of MINS (OR 0.832; 95% CI 0.554-1.251; p-value = 0.377). There were no significant associations between the two groups in type 1 MI, new-onset atrial fibrillation, in-hospital and 30-day mortality before and after balancing the use of remifentanil. However, the incidence of postoperative AKI was lower in the TIVA group (OR 0.362; 95% CI 0.194-0.675; p-value = 0.001). After balancing the use of remifentanil, volatile anesthesia and TIVA showed comparable effects on MINS in patients undergoing non-cardiac surgery without preoperative myocardial injury. Further studies are needed on the benefit of remifentanil infusion.

Antimicrobial resistance (AMR) has been a serious threat to human health, and combination therapy is proved to be an economic and effective strategy to fight the resistance. However, the abuse of drug combinations would conversely accelerate the spread of AMR. In our previous work, it had been concluded that the mutant selection indexes (SIs) of one agent against a specific bacterial strain are closely related to the proportions of two agents in a drug combination. To discover probable correlations, predictors and laws for further proposing feasible principles and schemes guiding the AMR-preventing practice, here three aspects were further explored. First, the power function (y=ax^b, a > 0) correlation between the SI (y) of one agent and the ratio value (x) of two agents in a drug combination was further established based on the mathematical and statistical analyses for those experimental data, and two rules a₁ × MIC₁ = a₂ × MIC₂ and b₁ + b₂ = -1 were discovered from both equations of y=a₁x^b1 and y=a₂x^b2 respectively for two agents in drug combinations. Simultaneously, it was found that one agent with larger MPC alone for drug combinations show greater potency for narrowing itself MSW and preventing the resistance. Second, a new concept as mutation-preventing selection index (MPSI) was proposed and used for evaluating the mutation-preventing potency difference of two agents in drug combinations, and the positive correlation between the MPSI and the mutant prevention concentration (MPC) or minimal inhibitory concentration (MIC) was subsequently established. Inspired by this, the significantly positive correlation, contrary to previous reports, between the MIC and the corresponding MPC of antimicrobial agents against pathogenic bacteria was established using one hundred and eighty-one of data pairs reported. These results together of above three aspects indicate that the MPCs in alone and combination are very important indexes for drug combinations to predict the mutation-preventing effects and the trajectories of collateral sensitivity, and while the MPC of an agent can be roughly calculated from its corresponding MIC. Subsequently, the former conclusion was further verified and improved by the antibiotic exposure to forty-three groups designed as different drug concentrations and various proportions. The results further proposed that the C/MPC for the agent with larger proportion in drug combinations can be considered as a predictor and is the key to judge whether the resistance and the collateral sensitivity occur to two agents. Based on these above correlations, laws, and their verification experiments, some principles were proposed, and a diagram of the mutation-preventing effects and the resistant trajectories for drug combinations with different concentrations and ratios of two agents was presented. Simultaneously, the reciprocal of MPC alone (1/MPC), proposed as the stress factors of two agents in drug combinations, together with their SI in combination, is the key to predict the mutation-preventing potency and control the trajectories of collateral sensitivity. Finally, a preliminary scheme for antimicrobial combinations preventing the AMR was further proposed for subsequent improvement research and clinic popularization, based on the above analyses and discussion. Moreover, some similar conclusions were speculated for triple or multiple drug combinations.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

That how to improve the sensitivity and the detection ability of the Large-caliber sensor is critical to satisfy the requirement of heavy vehicle wear condition monitoring. In this paper, we introduced the LC resonance principle to the design of sensor with large flow channel (7mm). The resonant exciting coil increases the impedance change of the exciting circuit caused by wear particles which magnify the current difference between the two exciting coils and improve the sensitivity of the sensor. The resonant induction coil greatly suppresses the interference signals and magnifies the weak induced electromotive force which is beneficial to enhance the detection ability. In order to boost the detectability for different materials particles, a phase controlled variable-frequency exciting system (PCVFES) was adopted to automatically switch the exciting frequency between 284kHz for ferromagnetic particles and 420KHz for non-ferromagnetic particles. For the weak signal detection, based on the essential characteristic of the signal, we apply a simpler method that modified lock-in amplifier (MLIA) rather than the conventional algorithms (Wavelet transform, EMD). Results show that using these methods the sensitivity and the detection ability of the sensor are significantly improved and the 75μm iron particles and 220μm copper particles were successfully detected which realizes the initial abnormal wear monitoring for the large flow project.

In the Formula Student Racing Car, the anti-deformation ability of the frame will affect the four-wheel positioning parameters of the racing car, and then affect the handling and stability performance of the racing car. The quality of the frame directly determines the power and economy of the racing car, so the performance of the frame is very important to the performance of the race. In order to improve the performance of the frame and reduce the total weight of the frame, the research on the lightweight design of the frame is particularly important. In this paper, based on the variable density method, the global topology optimization of the frame is carried out to obtain the distribution of the frame material, realize the efficient use of the material, and improve the torsional stiffness of the frame. Based on the adjoint variable method, the sensitivity analysis of the frame is carried out. According to the sensitivity analysis results, the size of the frame is optimized. The total mass of the frame is reduced by 12.8 %, and the performance of the maximum displacement and maximum stress is improved. The lightweight design of the frame is realized as a whole.

Obesity in the United States continues to worsen. Anthocyanin-rich fruits and vegetables provide a pragmatic dietary approach to slow its metabolic complications. Given American diet patterns, foods with high anthocyanin content could address dose-response challenges. In a placebo-controlled, randomized, crossover pilot study, determine the effect of 100% elderberry juice on measures of indirect calorimetry (IC), and insulin sensitivity/glucose tolerance. Overweight and obese adults were randomized to a 5-week study which included two 1-week periods of twice-daily elderberry juice (EBJ), or sugar-matched placebo consumption separated by a 3-week washout period. Following each 1-week test period, IC and insulin sensitivity/glucose tolerance was measured with a 3-hour meal tolerance test (MTT). Treatment differences were tested with linear mixed modeling. 22 prospective study volunteers (18F/4M) attended recruitment meetings, 10 volunteers completed the protocol, and 9 were analyzed for treatment differences. EBJ was well tolerated and compliance was 99.6%. Six IC measures (intervals) were created which coincided with 10-20 minute gaseous samplings in-between MTT blood samplings. Average CHO oxidation was significantly higher during the MTT after 1-week EBJ consumption (3.38 vs. 2.88 grams per interval, EBJ vs. placebo, p = 0.0113). Conversely, average fat oxidation was significantly higher during the MTT after 1-week placebo consumption (1.17 vs 1.47 grams per interval, EBJ vs. placebo, p = 0.0189). This was in-line with a significantly lower average respiratory quotient after placebo treatment (0.87 vs. 0.84, EBJ vs. placebo, p = 0.0114). Energy expenditure was not different. There was no difference in serum glucose or insulin response between treatments. This pilot study of free-living volunteers describes significant change in IC but not insulin sensitivity with an EBJ intervention. Controlled feeding and increased sample size will help determine the utility of EBJ on these outcomes.

Helicobacter Pylori (H. Pylori) is a common pathogen with high prevalence of infection in human populations. Diagnosis of H. Pylori infection is critical for its treatment, eradication, and prognosis. Biosensors have been demonstrated to be powerful for rapid onsite detection of pathogens, particularly for point-of-care test (POCT) scenarios. In this work, we propose a novel optical biosensor, based on nanomaterial porous silicon (PSi) and photonic surface state Tamm Plasmon Polariton (TPP), for detection of cytotoxin-associated antigen A (CagA) antigen of H. Pylori bacterium. We fabricated the PSi TPP biosensor, analysed its optical characteristics and demonstrated through experiments towards sensing of CagA antigen, that TPP biosensor has sensitivity of 100 pm/(ng/ml), limit of detection of 0.01 ng/ml, and specificity in terms of positive-to-negative ratio of more than six. From these performance factors, it can be concluded that TPP biosensor can serve as an effective tool for diagnosis of H. Pylori infection, either in analytical labs or in POCT applications.

It is unclear which noise exposure time window and noise characteristics during nighttime are most detrimental for sleep quality in real life settings. We have conducted a field study with 105 volunteers wearing a wrist actimeter to record their sleep during seven days, together with concurrent outdoor noise measurements at their bedroom window. Actimetry recorded sleep latency increased by 5.6 minutes (95% confidence interval: 1.6 to 9.6 minutes) per 10 dB(A) increase in noise exposure during the first hour after bedtime. Actimetry assessed sleep efficiency was significantly reduced by 2-3 percent per 10 dB(A) increase in measured outdoor noise (Leq, 1h) for the last three hours of sleep. For subjectively reported sleepiness, noise exposure during the last hour prior to wake up was most crucial with an increase in the sleepiness score of 0.31 units (95% CI: 0.08 to 0.54) per 10 dB(A) Leq,1h. Associations for estimated indoor noise were not more pronounced than for outdoor noise. Considering noise events in addition to equivalent sound pressure levels (Leq) only marginally improved the statistical models. Our study provides evidence that matching the nighttime noise exposure time window to the individual’s diurnal sleep-wake pattern results in a better estimate of detrimental nighttime noise effects on sleep. We found that noise exposure at the beginning and the end of the sleep is most crucial for sleep quality.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

African swine fever (ASF) is one of the major threats to pig production, and real-time PCR (qPCR) protocols are integral part of ASF laboratory diagnosis. With the pandemic spread of ASF, commercial kits have risen on the market. In Germany, the kits have to go through an approval process and thus, general validation can be assumed. However, they were never compared to each other. In this study, 12 commercial PCR kits were compared to an OIE recommended method. Samples representing different matrices, genome loads, and genotypes were included in a panel that was tested under diagnostic conditions. The comparison included user-friendliness, internal controls, and the time required. All qPCRs were able to detect ASFV genome in different matrices across all genotypes and disease courses. With one exception, there were no significant differences when comparing the overall mean. The overall specificity was 100 % [95 % CI 87.66 - 100], and the sensitivity was between 95 % and 100 % [95 % CI 91.11 - 100]. As can be expected, variability concerned samples with low genome load. Concluding, all tests were fit for purpose. The test system can therefore be chosen based on compatibility and prioritization of the internal control system.

G protein-coupled receptors (GPCRs) play a key role in many cellular signaling mechanisms, and must select among multiple coupling possibilities in a ligand-specific manner in order to carry out a myriad of functions in diverse cellular contexts. Much has been learned about the molecular mechanisms of ligand-GPCR complexes from Molecular Dynamics (MD) simulations. However, to explore ligand-specific differences in the response of a GPCR to diverse ligands, as is required to understand ligand bias and functional selectivity, necessitates creating very large amounts of data from the needed large-scale simulations. This becomes a Big Data problem for the high dimensionality analysis of the accumulated trajectories. Here we describe a new machine learning (ML) approach to the problem that is based on transforming the analysis of GPCR function-related, ligand-specific differences encoded in the MD simulation trajectories into a representation recognizable by state-of-the-art deep learning object recognition technology. We illustrate this method by applying it to recognize the pharmacological classification of ligands bound to the 5-HT2A and D2 subtypes of class A GPCRs from the serotonin and dopamine families. The ML-based approach is shown to perform the classification task with high accuracy, and we identify the molecular determinants of the classifications in the context of GPCR structure and function. This study builds a framework for the efficient computational analysis of MD Big Data collected for the purpose of understanding ligand-specific GPCR activity.

Insulin-like growth factor binding proteins (IGFBPs) are critical modulators of the metabolism. In adults, IGFBPs are associated with obesity and insulin resistance but the association of IGFBPs with metabolic homeostasis in children and adolescents is not fully characterized. In this study we investigated the association of plasma IGFBPs (IGFBP-1, 3 and 7) with weight status, central adiposity and cardiovascular disease markers Hs-CRP and Ox-LDL. A total of 420 adolescents (age 11-14 years) were randomly recruited from public middle schools in Kuwait. IGFBPs were measured using bead-based multiplexing while Hs-CRP and Ox-LDL were measured using ELISA. IGFBP-1 levels were significantly lower in obese and overweight participants compared to normal weight children. Only IGFBP-1 was negatively associated with waist circumference to height (WC/Ht) ratio. IGFBP-1 was negatively correlated with Hs-CRP while IGFBP-3 and IGFBP-7 were negatively correlated with Ox-LDL. These data demonstrate a robust negative association of IGFBP-1, but not IGFBP-3 or -7, with overweight and obesity, and the inflammation marker Hs-CRP. Central adiposity (WC/Ht ratio) was a stronger predictor of IGFBP-1 than BMI-for-age z-score. IGFBP-1 could thus be used as a sensitive predictive diagnostic tool for obesity and its subsequent effects in screening and monitoring of obesity-related metabolic complications in adolescents.

The challenge posed by multi-drug resistance (MDR) of pathogenic organisms, spectacularly manifested in the 6 “ESKAPE” bacterium (two Gram-positive, four Gram-negative) species, should invoke new comprehensive strategies, and needs cooperation of scientists with medical, veterinary and natural science background. This review is aimed at informing newcomers, coming from the field of biology and genetics, about problems related to rapidly emerging, new multi-drug resistant, pathogenic, bacteria. Unlike persistence, the antibiotic resistance is inherited. A functioning “resistance gene” makes a susceptible organism resistant to a given antibiotic, encoding for polypeptides capable of acting either as decomposing enzymes, or acting as trans-membrane pumps, or membrane structure components capable of modifying the permeability implementing a «by pass» mechanism enabling the antibiotic molecule to reach its cellular target(s). A functioning “sensitivity gene” encode for a polypeptide, capable (directly or indirectly) of transferring toxic molecules into target cells, or of metabolizing non-transferable to transferable, or non-toxic molecules to toxic derivatives. A gene of a normal function could act as a “sensitivity” gene in the presence of antibiotics of chemical structures similar to the natural substrate of the gene product, (enzyme or binding/ trans-membrane protein). The Agrocin 84 story is a good example. Multi-drug resistance is a phenotypic consequence of the sequential accumulation of mutations, and/or up-take of plasmids or genomic islands carrying resistance genes from the environment via horizontal gene transfer, mediated by conjugative plasmid or bacteriophage carrying mobile genetic elements. Both multi-drug resistance and collateral sensitivity are evolutionary products. Some revealed evolutionary process and their Lamarckian and Darwinian interpretations are discussed. Toolkits of comparative full-genome sequencing, genomics, experimental evolution and population genetics may provide perspectives for overcoming the invincibility of multi-drug panresistance. The status of some recently emerging pathogenic bacterium species with zoonic features and of veterinary background is also discussed.

Tularemia is a zoonotic disease caused by {\it Francisella tularensis} bacteria, a gram-negative coccobacillus-shaped bacterium. There are multiple transmission routes of the infection to humans such as consumption of contaminated food or water, handling of infected animals or bites from {\it haematophagous} arthropods (such as ticks, deer flies, or mosquitoes). In this study we focus on transmission via the bites of ticks and developed a deterministic model of ordinary and impulsive differential equations to gain insight in the differential effect of prescribed fire on {\it Demacenta variablis} and {\it Amblyomma americanum} ticks and the prevalence of tularemina. We found that prescribed fire differentially reduce the number of the two ticks with {\it A. americanum} reduced the least compare to {\it D. variablis} subsequently leading to differential increase of tularemia new infected cases in humans and rodents. Our result further indicates that the spatial arrangement of burn against unburn areas may not matter as either arrangement led to fewer ticks and reduction in tularemia transmission when prescribed fire was implemented. The results of this study provide important new understandings of the intricate effect of prescribed fire on tick species, and the dynamics of the tick-borne disease, tularemia disease in this study.

In this work, we demonstrate the preparation of easy-to-fabricate nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics and examine their properties including tunnel magnetoresistance, magnetic field sensitivity and temperature coefficient of the tunnel magnetoresistance. The tunnel magnetoresistance of nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics was modeled yielding values suitable for magnetoresistive sensor application. Such structures possess a narrow peak of magnetic flux sensibility located at about 125 mT. For magnetic flux measurement, single domain granules with superparamagnetic behavior should be applied. The predicted TMR magnetic flux sensitivities for granules with superparamagnetic behavior amount to about 7.7 % per T and 1.5 % per T for granules sizes of 6.8 nm and 4 nm, respectively. A drawback of the tunnel magnetoresistance of such nanogranular core-shell ceramics is the unacceptable large value of the temperature coefficient. Acceptable values, lower than 2 % per K, are obtained only at low temperatures (less than 100 K) or large magnetic flux densities (exceeding 6 T). Therefore, a Wheatstone bridge configuration should be adopted for magnetoresistive sensors design to compensate the effect of temperature.

Traumatic brain injury (TBI) is a major leading cause of death and disability. While previous studies regarding focal pathologies following TBI have been done, there is a lack of information concerning the role of analgesics and their influences on injury pathology. Buprenorphine (Bup), an opioid analgesic, is a commonly used analgesic in experimental TBI models. Our previous studies investigated the acute effects of Buprenorphine-sustained release-Lab (Bup-SR-Lab) on diffuse neuronal/glial pathology, neuroinflammation, cell damage, and systemic physiology. The current study investigated the longer-term chronic outcomes of Bup-SR-Lab treatment at 4 weeks following TBI utilizing a central fluid percussion injury (cFPI) model in adult male rats. Histological assessments of physiological changes, neuronal damage, cortical and thalamic cytokine expression, microglial and astrocyte morphological changes, and myelin alterations were done, as we had done in our acute study. In the current study the Whisker Nuisance Task (WNT) was also performed pre- and 4w post-injury to assess changes in somatosensory sensitivity following saline or Bup-SR-Lab treatment. Bup-SR-Lab treatment had no impact on overall physiology or neuronal damage at 4w post-injury regardless of region or injury, nor did it have any significant effects on somatosensory sensitivity. However, greater IL-4 cytokine expression with Bup-SR-Lab treatment was observed compared to saline treated animals. Microglia and astrocytes also demonstrated region-specific morphological alterations associated with Bup-SR-Lab treatment, in which cortical microglia and thalamic astrocytes were particularly vulnerable to Bup-mediated changes. There were discernable injury-specific and region-specific differences regarding myelin integrity and changes in specific myelin basic protein (MBP) isoform expression following Bup-SR-Lab treatment. This study indicates that use of Bup-SR-Lab could impact TBI-induced glial alterations in a region-specific manor 4w following diffuse brain injury.

The process of revitalising quiescent cells in order for them to proliferate plays a pivotal role in the repair of warn out tissues as well as for tissue homeostasis. This process is also crucial in the growth, development and well-being of higher multi-cellular organisms such as mammals. Deregulation of quiescent-proliferation transition is related to many diseases, in particular cancer. Recent studies have revealed that this process is regulated tightly by the Rb−E2F bistable switch mechanism. Based on experimental observations, in this study, we formulate a mathematical model to examine the effect of the growth factor concentration on the proliferation-quiescence transition in human cells. Working with a non-dimensionalised model, we prove positivity, boundedness and uniqueness of solutions. To understand model solution behaviour close to bifurcation points, we carry out bifurcation analysis, which is further verified by use of numerical bifurcation analysis, sensitivity analysis and numerical simulations. Indeed, bifurcation and numerical analysis of the model predicted a transition between stable, bistable and stable states, which are dependent on the growth factor concentration parameter (GF). The derived predictions confirm experimental observations.

Most of the research of mental fatigue evaluation mainly concentrated on some indexes that require sophisticate and large instruments which make the detection of mental fatigue cumbersome, time-consuming, and difficult to apply on a large scale. A quick and sensitive mental fatigue detection index is necessary so that mental workers can be alerted in time and take corresponding countermeasures. But to date, no studies have compared the sensitivity of common objective evaluation indexes. To solve these problems this study recruited 56 human subjects. These subjects were evaluated using six fatigue indexes: the Stanford sleepiness scale, digital span, digital decoding, short-term memory, critical flicker fusion frequency (CFF), and speed perception deviation. The results of fatigue tests before and after mental fatigue were compared, and a one-way analysis of variance (ANOVA) was performed on the speed perception deviation. The result indicated the significance of this index. Considering individual differences, the relative fatigue index (RFI) was proposed to compare the sensitivity of the indexes. The results showed that when the self-rated fatigue grade changed from non-fatigue to mild fatigue, the ranges of RFI values for digital span, digital decoding, short-term memory and CFF were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. Correspondingly, when the self-rated fatigue grade changed from non-fatigue to severe fatigue, the ranges of RFI values for the above indexes were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. These results suggest that the sensitivity of the digital decoding, digital span, short-term memory, and CFF decreased sequentially when the self-evaluated fatigue grade changed from no fatigue to mild or severe fatigue. The RFI individuality of the speed perception deviation is highly variable and is not suitable as an evaluation index. In mental fatigue testing, digital decoding testing can provide faster, more convenient, and more accurate results.

Studies performed at single-cell resolution have demonstrated the physiological significance of cell-to-cell variability. Various types of mathematical models and systems analyses of biological networks have further been used to gain a better understanding of the sources and regulatory mechanisms of such variability. In this work, we present a novel sensitivity analysis method, called molecular density function perturbation (MDFP), for the dynamical analysis of cellular heterogeneity. The proposed analysis is based on introducing perturbations to the density or distribution function of the cellular state variables at specific time points, and quantifying how such perturbations affect the state distribution at later time points. We applied the MDFP analysis to a model of signal transduction pathway involved in TRAIL (tumor necrosis factor-related apoptosis-inducing ligand)-induced apoptosis in HeLa cells. The MDFP analysis showed that caspase-8 activation regulates the timing of the switch-like increase of cPARP (cleaved poly(ADP-ribose) polymerase), an indicator of apoptosis. Meanwhile, the cell-to-cell variability in the commitment to apoptosis depended on mitochondrial outer membrane permeabilization (MOMP) and events following MOMP, including the release of Smac (second mitochondria-derived activator of caspases) and cytochrome-C from mitochondria, the inhibition of XIAP (X-linked inhibitor of apoptosis) by Smac and the formation of apoptosome.

Based on the geologic conditions of natural gas hydrate (NGH) accumulations in the Shenhu area, northern slope of the South China Sea, this paper used a method of combining reservoir stimulation technique (RST) with depressurization to investigate the conversion efficiency of marine NGH reservoirs in different intrinsic permeability and initial NGH saturation conditions, and analyze the influence of variably-stimulation effect on marine NGH conversion efficiency in different accumulation conditions, provided a reference scheme for improving the NGH conversion efficiency in the Shenhu area. In this work, we performed calculations for the variations in CH4 production rate and cumulative volume of CH4 in different initial NGH saturation, intrinsic permeability and stimulation effect conditions, variance analysis and range analysis methods were used to analyze the significance of these key factors and their interaction, and investigated the sensitivity of stimulation effect on NGH conversion efficiency, respectively. The simulation results showed that stimulation effect have a significant influence on NGH conversion efficiency, and the influence of interaction between these three factors were not obvious. Possibly most important, we clarified an optimum stimulation effect for higher NGH conversion efficiency under different accumulation conditions, especially in low-permeability and high-saturation, which corresponding stimulation effect were different.

Highly flexible manufacturing systems require continuous run-time (self-) optimization of processes with respect to various parameters, e.g. efficiency, availability, energy consumption etc. A promising approach for achieving (self-) optimization in manufacturing systems is the usage of the context sensitivity approach. Thereby the Cyber-Physical Systems play an important role as sources of information to achieve context sensitivity. In this paper it is demonstrated how context sensitivity can be used to realize a holistic solution for (self-) optimization of discrete flexible manufacturing systems, by making use of Cyber-Physical System integrated in manufacturing systems/processes. A generic approach for context sensitivity, based on self-learning algorithms, is proposed aiming at a various manufacturing systems. The new solution is propos encompassing run-time context extractor and optimizer. Based on the self-learning module both context extraction and optimizer are continuously learning and improving their performance. The solution is following Service Oriented Architecture principles. The generic solution is developed and then applied to two very different manufacturing processes. This paper proposes a holistic solution to achieve context sensitivity for Flexible Manufacturing Systems, whereby the knowledge created by applying the context sensitivity approach can be used for (self-) optimization of manufacturing processes.

The sensitivity of exercise ECG is marginally sufficient for detection of mild reduction of coronary blood flow in patients with early coronary atherosclerosis. Here we describe the application of new technique of ECG registration/analysis – ultrahigh resolution ECG (UHR ECG) – for early detection of myocardial ischemia (MIS). The utility of UHR ECG vs. conventional ECG (C ECG) was tested in anesthetized rats and pigs. Transmural MIS was induced in rats by the ligation of the left coronary artery (CA). In pigs, subendocardial ischemia of variable extent was produced by stepwise inflation of balloon within the right CA causing 25-100% reduction of its lumen. In rats, a reduction in power spectral density (PSD) in high-frequency (HF) channel of UHR ECG was registered at 60 s after ischemia (power 0.81±0.14 vs. 1.25±0.12 mW at baseline, p<0.01). This was not accompanied by any ST segment elevation on C ECG. In pigs, PSD in HF channel of UHR ECG was significantly decreased at 25% reduction of CA lumen, while ST segment on C ECG remained unchanged. In conclusion, UHR ECG enabled earlier detection of transmural MIS compared to C ECG. PSD in HF-channel of UHR ECG demonstrated greater sensitivity in the settings of subendocardial ischemia.

Multiphase systems are important in minerals processing, and usually include solid-solid and solid-fluid systems. Examples of operations in multiphase systems include flotation, dewatering, and magnetic separation, among several other unit operations. In this paper, the current trends in the process system engineering tasks of modeling, design, and optimization, in multiphase systems, are analyzed. Different scales of size and time are included, and therefore the analysis includes modeling at the molecular level and unit operation level, and the application of optimization for the design of a plant. New strategies for the modeling and optimization of multiphase systems are also included, with a strong focus on the application of artificial intelligence (AI) and the combination of experimentation and modeling with response surface methodology (RSM). The paper finishes with tools to study the uncertainty, both epistemic and stochastic, which is present in all mineral processing operations. It is shown that all these areas are very active and can help to understand, operate, design, and optimize mineral processing that involves multiphase systems.

Background: Thyroid nodules are common, affecting nearly 65% of the general population. While they are widespread, it's crucial to recognize that the majority of these nodules are not cancerous and can be effectively managed through careful monitoring. Thyroid ultrasound is commonly used to evaluate thyroid nodules owing to its low cost, wide availability and technical ease of application. In sonography, it's crucial to assess characteristics and vascular flow. Yet, conventional color and power Doppler ultrasound may not always effectively capture small vessels and low velocities due to their limitations. Superior Microvascular Imaging can display the blood flow of small vessels and low-velocity blood flow, which is difficult to visualize with conventional Doppler ultrasound. Meanwhile other thyroid scans, that utilize either [99mTc] pertechnetate or (18)F-fluorodeoxyglucose, can categorize nodules as hyperactive ('hot'), exhibiting normal activity ('warm'), or having reduced/no activity ('cold'). Thus, the main goal of screening and tracking thyroid nodules is to improve the management of potentially worrisome thyroid malignancies. Methodology: The study was conducted within the structural framework of a network meta-analysis, with the index tests being - SMI, Radionuclide Scanning and Color Doppler, and the general link between them being the reference gold standard. The data collection involved searching for all pertinent literature using PubMed, Google Scholar, and the Cochrane Library databases. The essential data was extracted following the application of specific inclusion and exclusion criteria.This meta-analysis included 7 RCTs with 1,152 patients for Radionuclide Scanning, 10 RCTs with 1,847 patients for SMI and 8 RCTs with 4,480 patients for Color Doppler. They were analyzed using the QualSyst tool and the risk of bias was evaluated by using QUADAS-2 analysis.The statistical software packages MetaDiSc 1.4, RevMan (Review Manager, version 5.3), SPSS (Statistical Package for the Social Sciences, version 20) and Excel in Stata 14 were used to perform the statistical analyses. Result: According to the findings, the sensitivity for Radionuclide Scanning is calculated as 0.79 (range: 0.76 to 0.81) and specificity as 0.55 (range: 0.50 to 0.60) with a 95% confidence interval. The overall diagnostic odds ratio (DOR) for Radionuclide Scanning Is 10.54.Additionally, with a 95% confidence interval, SMI exhibits a sensitivity of 0.82 (with a range of 0.79 to 0.84) and a specificity of 0.86 (with a range of 0.84 to 0.88), while the overall DOR is approximately 25.73. Color Doppler demonstrates a calculated sensitivity of 0.71 (ranging from 0.69 to 0.74) and specificity of 0.81 (ranging from 0.79 to 0.83) with a 95% confidence interval, while its DOR is 13.48.Conclusion: As evidenced by this meta-analysis, blood flow dependent imaging techniques are superior in their abilities to be used as diagnostic tests, especially in conjunction with their use in detecting thyroid nodules. This study offers a starting point for delving deeper into the utilization of Radionuclide Imaging, Superior Microvascular Imaging and Color Doppler in diagnosing thyroid nodules in a clinical setting. Key Words: - Thyroid Nodule, Radionuclide Scanning, Superior Microvascular Imaging, Color Doppler Diagnosis, Sensitivity, Specificity, Diagnostic imaging

The extreme environmental issues and the resulting needs to save energy have turned the attention to electrification of energy applications. One of the key components involved in energy efficiency improvements is the appropriate conception and manufacturing of electric machines. This paper overviews the electromagnetic analysis governing the behavior of permanent magnets that enabled substantial efficiency gains in recent electric machine developments. Particular emphasis is given to model the properties and losses developed in permanent magnets in the emerging high speed applications. In addition, the investigation of properties and harmonic losses related to ferromagnetic materials constituting the machine magnetic circuits are equally analyzed and discussed. The experimental validation of the implemented methodologies and developed models with respect to the obtained precision is reported. The introduction of mixed numerical techniques based on the finite element method intended to appropriately represent the different physical phenomena encountered is outlined and discussed. Finally, fast and accurate simulation techniques including aggregated lumped parameter models considering harmonic losses associated with inverter supplies are commented.

Structural and biochemical studies have recently revealed a range of rationally engineered nanobodies with efficient neutralizing capacity against SARS-CoV-2 virus and resilience against mutational escape. In this work, we combined atomistic simulations and conformational dynamics analysis with the ensemble-based mutational profiling of binding interactions for a diverse panel of SARS-CoV-2 spike complexes with nanobodies. Using this computational toolkit, we identified dynamic signatures and binding affinity fingerprints for the SARS-CoV-2 spike protein complexes with nanobodies Nb6 and Nb20, VHH E, a pair combination VHH E+U, a biparatopic nanobody VHH VE, and a combination of CC12.3 antibody and VHH V/W nanobodies. Through ensemble-based deep mutational profiling of stability and binding affinities, we identify critical hotspots and characterize molecular mechanisms of SARS-CoV-2 spike protein binding with single ultra-potent nanobodies, nanobody cocktails and biparatopic nanobodies. By quantifying dynamic and energetic determinants of the SARS-CoV-2 S binding with nanobodies, we also examine the effects of circulating variants and escaping mutations. We found that mutational escape mechanisms may be controlled through structurally and energetically adaptable binding hotspots located in the host receptor-accessible binding epitope that are dynamically coupled to the stability centers in the distant epitope targeted by VHH U/V/W nanobodies. The results of this study suggested a mechanism in which through cooperative dynamic changes, nanobody combinations and biparatopic nanobody can modulate the global protein response and induce the increased resilience to common escape mutants.

There is a potential for synergy effects in utilizing CO2 for both enhanced gas recovery (EGR) and geothermal energy extraction (CO2-plume geothermal, CPG) from natural gas reservoirs. This “combined CO2-EGR–CPG system” has been introduced as a feasible approach that constitutes a CO2 Capture double-Utilization and Storage (CCUUS) system. In this study, we carry out reservoir simulations, using TOUGH2, to evaluate the sensitivity of the natural gas recovery, pressure buildup, and geothermal power generation performance of the combined system to various key reservoir and operational parameters. The reservoir parameters include horizontal permeability, permeability anisotropy, reservoir temperature, and pore-size-distribution index; while the operational parameters include wellbore diameter and ambient surface temperature. Using an example of a natural gas reservoir model, we also investigate the effects of different strategies of transitioning from the CO2-EGR stage to the CPG stage on the energy-recovery performance metrics and on the two-phase fluid-flow regime in the production well. The simulation results show that overlapping the CO2-EGR and CPG stages and having a relatively brief period of CO2 injection but no production (which we call the CO2-plume establishment stage) achieves the best overall energy (natural gas and geothermal) recovery performance. Permeability anisotropy and reservoir temperature are the parameters the natural gas recovery performance of the combined system is most sensitive to. The geothermal power generation performance is most sensitive to the reservoir temperature and the production wellbore diameter. The results of this study pave the way for future CPG-based geothermal power-generation optimization studies. For a CO2-EGR–CPG project, the results can be a guide regarding the required accuracy of the reservoir parameters during exploration and data acquisition.

In a limestone quarry mine, fragmentation is a crucial outcome of blasting operations. The optimization of blasting operations greatly benefits from the prediction of rock fragmentation. The main factors that affect fragmentation are rock mass characteristics, blast geometry, and explosive properties. This paper is a step towards the implementation of machine learning and deep learning algorithms for predicting the extent of fragmentation (in percentage) in opencast mining. Various parameters can affect fragmentation. But, in this paper initially, ten parameters (spacing, drill hole diameter, burden, average bench height, powder factor, number of holes, charge per delay, uniaxial compressive strength, specific drilling, and stemming) are collected to train the model. However, due to a weak correlation with rock fragmentation, drill diameter, Average bench height, compressive strength, stemming, and charge per delay are eliminated to reduce model complexity. A total of 219 data sets having five input features i.e., the number of holes, spacing, burden, specific drilling, and powder factor are used to develop the models. To predict rock fragmentation due to blasting in limestone quarry mines, both machine learning models (Random Forest Regression (Bagging), Support Vector Regression, and XG Boost Regression (Boosting)), as well as a deep learning model (Neural Network Regression), are applied to develop a model that can optimize the prediction of fragmentation. The Artificial neural network model optimization showed that the model with architecture 64-32-16-1 can perform well giving MSE (mean squared error) values of 41.32 and 28.59 on training and test data respectively. The R2 value for both training and test is 0.83. Random Forest regression is also performing well compared to SVR and XG boost with the MSE value 12.37 and 9.89 on training and testing data respectively. Here, the R2 value for both sets are 94%. Based on the permutation importance and Shapely plot values, the powder factor has the highest impact, and the burden has the lowest impact on fragmentation.

Controlling the selectivity of detonation initiation reaction of explosive is a Holy Grail, and it seems to be an “idiot's daydream”, by strengthening external electric field, to reduce the explosive sensitivity. The effects of external electric fields on the initiation reactions in NH2NO2∙∙∙NH3, a model system of the nitroamine explosive with alkaline additive, were investigated at the MP2/6-311++G(2d,p) and CCSD/6-311++G(2d,p) level. The concerted effect in the intermolecular hydrogen exchange is characterized by an index of the imaginary vibrations. Due to the weakened concerted effects by the electric field along the −x-direction opposite to the “reaction axis”, the dominant reaction changes from the hydrogen exchange to 1,3-intramolecular hydrogen transference with the increase of the field strengths. Furthermore, the stronger the field strengths, the higher the barrier heights become, indicating the lower sensitivities. Therefore, by strengthening the field strength and adjusting the orientation between the field and “reaction axis”, not only can the reaction selectivity be controlled, but also the sensitivity can be reduced, in particular under a super-strong field. Thus, a traditional concept, which the explosive is dangerous under the super-strong external electric field, is broken theoretically. Compared to the neutral medium, the low sensitivity of the explosive with alkaline can be achieved under the stronger field. Employing atoms in molecules, reduced density gradient and surface electrostatic potentials, the origin of the reaction selectivity and sensitivity change is revealed. This work provides a new idea to the technical improvement for adding the external electric field into the explosive system.

Early diagnosis and treatment have always been highly desired in the fight against cancer, and detection of circulating tumor DNA (ctDNA) has recently been touted as highly promising for early cancer screening. Consequently, the detection of ctDNA in liquid biopsy gains much attention in the field of tumor diagnosis and treatment, which has also attracted research interest from the industry. However, traditional gene detection technology is difficult to achieve low cost, real-time and portable measurement of ctDNA. Electroanalytical biosensors have many unique advantages such as high sensitivity, high specificity, low cost and good portability. Therefore, this review aims to discuss the latest development of biosensors for minimal-invasive, rapid, and real-time ctDNA detection. Various ctDNA sensors are reviewed with respect to their choices of receptor probes, detection strategies and figures of merit. Aiming at the portable, real-time and non-destructive characteristics of biosensors, we analyze their development in the Internet of Things, point-of-care testing, big data and big health.

Ultrasonic measurements are used in civil engineering for structural health monitoring of concrete infrastructures. The late portion of the ultrasonic wavefield, the coda, is sensitive to small changes in the elastic moduli of the material. Coda Wave Interferometry (CWI) correlates these small changes in the coda with the wavefield recorded in intact, or unperturbed, concrete specimen to reveal the amount of velocity change that occurred. CWI has the potential to detect localised damages and global velocity reductions alike. In this study, the sensitivity of CWI to different types of concrete mesostructures and their damage levels is investigated numerically. Realistic numerical concrete models of concrete specimen are generated and damage evolution is simulated using the discrete element method. In the virtual concrete lab, the simulated ultrasonic wavefield is propagated from one transducer using a realistic source signal and recorded at a second transducer. Different damage scenarios reveal a different slope in the decorrelation of waveforms with the observed reduction in velocities in the material. Finally, the impact and possible generalizations of the findings are discussed and recommendations are given for a potential application of CWI in concrete at structural scale.

The COVID-19 pandemic has created huge damage to society and brought panics around the world. Such panics can be ascribed to the seemingly deceptive features of the COVID-19: compared to other deadly viral outspreads, it has medium transmission and mortality rates. As a result, the severity of the causative coronavirus, SARS-CoV-2, was deeply underestimated by the society at the beginning of the COVID-19 outbreak. Based on this, in this review, we define the viruses with features similar to those of SARS-CoV-2 as the Panic Zone viruses. To contain those viruses, accurate and fast diagnosis followed by effective isolation and treatment of patients are pivotal at the early stage of virus breakouts. This is especially true when there is no cure or vaccine available for a transmissible disease, which is the case for current COVID-19 pandemic. As of January 2021, more than two hundred kits for the COVID-19 diagnosis on the market are surveyed in this review, while emerging sensing techniques for SARS-CoV-2 are also discussed. It is of critical importance to rationally use these kits for the efficient management and control of the Panic Zone viruses. Therefore, we discuss guidelines to select diagnostic kits at different outbreak stages of the Panic Zone viruses, SARS-CoV-2 in particular. While it is of utmost importance to use nucleic acid-based detection kits with low false negativity (high sensitivity) at the early stage of an outbreak, the low false positivity (high specificity) gains its importance at later stages of the outbreak. When a society is set to reopen from the lock-down stage of the COVID-19 pandemic, it becomes critical to have antibody based immunoassay kits with high specificity to identify people who can safely return to the society after their recovery of SARS-CoV-2 infections. Given that the emergence of mutant viruses at the beginning of 2021 has complicated current battle against the COVID-19, we also discussed approaches and guidelines to detect viral mutants in the middle of the second wave of the pandemic that started at the end of 2020. Finally, since a massive attack from a viral pandemic requires a massive defense from the whole society, we urge both government and private sectors to research and develop more affordable and reliable point-of-care testing (POCT) kits, which can be used massively by the general public (and therefore called as massive POCT) to contain Panic Zone viruses in future.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

At an energy flux imbalance of about 1 W m–2, the ocean is storing 90 % of the heat accumulating by global warming. However, neither the causes nor the responsible geophysical processes are sufficiently well understood. More detailed investigations of the different phenomena contributing to the oceanic energy balance are warranted. Here, the role of low-level marine clouds in the air-sea interaction is analysed. TEOS-10, the International Thermodynamic Equation of State of Seawater – 2010, is exploited for a rigorous thermodynamic description of the climatic trend of the Lifted Condensation Level (LCL) of the marine troposphere. Rising Sea-Surface Temperature (SST) at constant Relative Humidity (RH) is elevating marine clouds, cooling the cloud base and reducing the downward thermal radiation. This LCL feedback effect is negative and counteracting ocean warming. At the current global SST of about 292 K, the net radiative heat flux from the ocean surface to the LCL cloud base is estimated to 24 W m–2. Per degree of SST increase, this net flux is expected to be enhanced by almost 0.5 W m–2. The climatic LCL feedback effect is relevant for the ocean’s energy balance and may thermodynamically rigorously be modelled in terms of TEOS-10 equations. LCL height may serve as a remotely measured, sensitive estimate for sea surface relative fugacity, or conventional relative humidity.

The comprehensive anabolic effects of insulin throughout the body, in addition to the control of glycemia, also include ensuring lipid homeostasis and anti-inflammatory modulation, especially in adipose tissue (AT). The prevalence of obesity, defined as a body mass index (BMI) ≥ 30 kg/m2, has been increasing worldwide on a pandemic scale with accompanying syndemic health problems, including glucose intolerance, insulin resistance (IR) and diabetes. Impaired tissue sensitivity to insulin or IR paradoxically leads to diseases with an inflammatory component despite hyperinsulinemia. Therefore, an excess of visceral AT in obesity initiates chronic low-grade inflammatory conditions that interfere with insulin signaling via insulin receptor (INSR). Moreover, in response to IR, hyperglycemia itself stimulates a primarily defensive inflammatory response associated with the subsequent release of numerous inflammatory cytokines and a real threat of organ function deterioration. In this review, all components of this vicious cycle are characterized with particular emphasis on the interplay between insulin signaling and both the innate and adaptive immune responses related to obesity. Increased visceral AT accumulation in obesity should be considered the main environmental factor responsible for the disruption in the epigenetic regulatory mechanisms in the immune system, resulting in autoimmunity and inflammation.

Biosensors detect specific bio-analytes by generating a measurable signal from the interaction between the sensing element and the target molecule. Surface acoustic wave (SAW) biosensors offer unique advantages due to their high sensitivity, real-time response capability, and label-free detection. The typical SAW modes are the Rayleigh mode and the shear-horizontal mode. Both present pros and cons for biosensing applications and generally need different substrates and device geometries to be efficiently generated. This study investigates and characterizes ultra-high-frequency (UHF-) SAW resonator biosensors. It reveals the simultaneous presence of the two typical SAW modes, clearly separated in frequency, called slow and fast. The two modes are studied by numerical simulations and biosensing experiments with the glial-fibrillary-acidic-protein (GFAP) biomarker. The slow mode is generally more sensitive to changes in surface properties, such as temperature and mass changes, by a factor of about 1.4 with respect to the fast mode.