Achieving global goals on sustainable nutrition, health, and wellbeing will depend on delivering enhanced diets to humankind. This will require, among others, instantaneous access to information on food quality at key points within agri-food systems. Although stationary methods are usually used to quantify grain quality (wet-lab chemistry, benchtop NIR spectrometer); these do not suit many required user-cases, such as stakeholders in decentralized agri-food-chains that are typical for emerging economies. Therefore, we explored new technologies and models that might aid these particular user-cases. For this purpose, we generated the NIR spectra of 328 grain samples from multiple cereals (finger millet, foxtail millet, maize, pearl millet, sorghum) with a standard benchtop NIR Spectrometer (DS2500, FOSS) and a novel mobile NIR-based sensor (HL-EVT5, Hone). We explored a range of classical deterministic and novel machine learning (ML)-driven models to build calibrations out of the NIR spectra. We were able to build relevant calibrations out of both types of spectra. At the same time, ML-based methods enhanced the prediction capacity of calibration models compared to classical deterministic methods. We also documented that the prediction of grain protein content based on NIR spectra generated by a mobile sensor (HL-EVT5, Hone) was highly relevant for quantitative protein predictions (R2 = 0.91, RMSE = 0.97, RPD = 3.48). Thus, the findings of this study lay the foundations on which to expand the utilization of NIR spectroscopy applications for agricultural research and development.

Near-infrared spectroscopy (NIRS) was implemented to monitor the moisture content of broadleaf litters. Partial least-squares regression (PLSR) models, incorporating optimal wavelength selection techniques, have been proposed to better predict the litter moisture of forest floor. Three broadleaf litters were used to sample the reflection spectra corresponding the different degrees of litter moisture. Maximum normalization preprocessing technique was successfully applied to remove unwanted noise from the reflectance spectra of litters. Four variable selection methods were also employed to extract the optimal subset of measured spectra for establishing the best prediction model. The results showed that the PLSR model with the peak of beta coefficients method was the best predictor among all candidate models. The proposed NIRS procedure is thought to be a suitable technique for on-the-spot evaluation of litter moisture.

XPS and ARXPS characterization of surface layers resulting from the functionalization of polymers such as PVC modified with MPTMS and APTES is challenging due to the signals overlap, deriving both from the substrate and the functionalized layers. In this work, a freshly cleaved, ideally flat gold surface was used as carbon-free model substrate functionalized with MPTMS and subsequently grafted with APTES. Avoiding the overlap of signals from carbon atoms present in the substrate, the signals in the C1s, O1s, Si2p, S2p and N1s high-resolution spectra could be assigned to the MPTMS / APTES functionalized layer only and the curve fitting parameters could be determined. Quantitative analysis was in very good agreement with the expected stoichiometry of the functionalized layer, confirming the adopted curve fitting procedure. In addition, it was found that one molecule of APTES grafted two MPTMS via silane groups. ARXPS allowed determining the thickness of the functionalized layers: MPTMS thickness was found to be 0.5 (0.2) nm, MPTMS + APTES thickness 1.0 (0.2) nm in good agreement with Avogadro model calculations. This approach can be considered a powerful tool for characterising functionalized surfaces of more complex systems by XPS.

Laser-induced periodic surface structures (LIPSS) have gained significant attention due to their ability to modify the surface morphology of materials at the micro-nanoscale and show great promise for surface functionalization application. In this study, we specifically investigate the formation of LIPSS in silicon substrates and explore their impact on Surface-Enhanced Raman Spectroscopy (SERS) applications. This study reveals a stepwise progression of LIPSS formation in silicon, involving three distinct stages of LIPSS: 1) integrated Low-Spatial-Frequency LIPSS (LSFL) and High-Spatial-Frequency LIPSS (HSFL), 2) principally LSFL and 3) LSFL at the edge of the irradiated spot, elucidating the complex interplay between laser fluence, pulse number, and resulting surface morphology. Furthermore, from an application standpoint, these high-quality multi-scale periodic patterns lead to the next step of texturing the entire silicon surface with homogeneous LIPSS for SERS application. The potential of LIPSS-fabricated silicon substrates for enhancing SERS performance is investigated using thiophenol as a test molecule. The results indicate that the Au-coated combination of LSFL and HSFL substrate showcased the highest enhancement factor (EF) of 1.38 × 10^6. This pronounced enhancement is attributed to the synergistic effects of Localized Surface Plasmon Resonance (LSPR) and Surface Plasmon Polaritons (SPPs), intricately linked to HSFL and LSFL characteristics. These findings contribute to understanding LIPSS formation in silicon and their applications in surface functionalization and SERS, paving the way for sensing platforms.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

This study aims to assess the potential of the LDAS-Monde a land data assimilation system developed by Météo-France to monitor the impact of the 2018 summer heatwave over western Europe vegetation state. The LDAS-Monde is forced by the ECMWF’s (i) ERA5 reanalysis, and (ii) the Integrated Forecasting System High Resolution operational analysis (IFS-HRES), used in conjunction with the assimilation of Copernicus Global Land Service (CGLS) satellite derived products, namely the Surface Soil Moisture (SSM) and the Leaf Area Index (LAI). Analysis of long time series of satellite derived CGLS LAI (2000-2018) and SSM (2008-2018) highlights marked negative anomalies for July 2018 affecting large areas of North Western Europe and reflects the impact of the heatwave. Such large anomalies spreading over a large part of the considered domain have never been observed in the LAI product over this 18-yr period. The LDAS-Monde land surface reanalyses were produced at spatial resolutions of 0.25°x0.25° (January 2008 to October 2018) and 0.10°x0.10° (April 2016 to December 2018). Both configuration of the LDAS-Monde forced by either ERA5 or HRES capture well the vegetation state in general and for this specific event, with HRES configuration exhibiting better monitoring skills than ERA5 configuration. The consistency of ERA5 and IFS HRES driven simulations over the common period (April 2016 to October 2018) allowed to disentangle and appreciate the origin of improvements observed between the ERA5 and HRES. Another experiment, down-scaling ERA5 to HRES spatial resolutions, was performed. Results suggest that land surface spatial resolution is key (e.g. associated to a better representation of the land cover, topography) and using HRES forcing still enhance the skill. While there are advantages in using HRES, there is added value in down-scaling ERA5, which can provide consistent, long term, high resolution land reanalysis. If the improvement from LDAS-Monde analysis on control variables (soil moisture from layers 2 to 8 of the model representing the first meter of soil and LAI) from the assimilation of SSM and LAI was expected, other model variables benefit from the assimilation through biophysical processes and feedbacks in the model. Finally, we also found added value of initializing 8-day land surface HRES driven forecasts from LDAS-Monde analysis when compared with model only initial conditions.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

Definitions of bronchopulmonary dysplasia (BPD) or post-prematurity respiratory disease (PPRD) aim to stratify the risk of mortality and morbidity, with an emphasis on long-term respiratory outcomes. There is no univocal classification of BPD, due to its complex multifactorial nature and the substantial heterogeneity of clinical presentation. Currently, there is no definitive cure available for extremely premature very-low-birth-weight infants with BPD, and challenges in finding targeted preventive therapies persist. However, innovative stem cells-based postnatal therapies targeting BPD-free survival are emerging, which are likely to be offered in the first few days of life to higher-risk subpopulations of premature infants. Hence the need for easy-to-use noninvasive tools for a standardized, precise and reliable BPD assessment at a very early stage, to support clinical decision-making and to predict the response to treatment. In this non-systematic review, we present an overview of strategies for monitoring preterm infants with early and evolving BPD-PPRD, and make some remarks on future prospects, with a focus on near-infrared spectroscopy (NIRS).

Near-infrared (NIR) photodetectors (PDs) have attracted much attention in noninvasive medical diagnosis and treatment. Especially, the self-filtered NIR PDs are highly demandable for tremendous biomedical application due to their strong ability in wavelength discrimination. In this work, we designed and then fabricated a Si micro-holes array/Graphene (Si MHA/Gr) van der Waals (vdW) Schottky NIR photodiode by using PbS quantum dots (QDs) coating. The device exhibits a unique self-filtered NIR response with a responsivity of 0.7 A/W at -1 V and a response time of 61 μs, which are higher than that without PbS QDs coating and even most of previous Si/Gr Schottky photodiodes. The light trapping of the Si MHA and the PbS QDs coating can be attributed to the high responsivity of the vdW photodiode. Furthermore, the presented NIR photodiode can also be integrated in photoplethysmography (PPG) for real-time heart-rate (HR) monitoring. The extracted HR is in great accord with the value measured with the patient monitor by analyzing the Fourier transform of the stable and reliable fingertip PPG waveform, suggesting its potential for practical applications.

When in operation, the 25 kV traction networks may encounter the contact wire short circuits to rails or ground. The short-circuit conditions cause high-intensity magnetic fields (EMFs), which, despite the short duration of exposure, can negatively affect electronic devices and lead to significant induced voltage on adjacent power lines. There can be two main types of emergency conditions in 25 kV traction networks: the contact wire short circuit to the rail, when the supports are grounded to the rail track; and the contact wire short circuit to the ground in sections with supports disconnected from the rails. A three-dimensional electromagnetic field near a metal support when a short-circuit current flows through it is characterized by a complex spatial structure, which significantly complicates the calculations of intensities. The paper discusses the results of computer modeling aimed at determining the EMF intensity in the described emergencies. The objects involved in modeling were represented by segments of thin wires to calculate the electric charge distribution and find out the EMF intensity. This approach is implemented in the Fazonord software. The modeling results have shown that EMF intensities near the support grow significantly; their levels decrease noticeably as one moves away from the support; and that the three-dimensional electromagnetic field under the considered emergency conditions has a complex spatial structure.

In the leading/trailing edge’s adaptive machining of the near-net-shaped blade, a small portion of the theoretical part is retained for securing aerodynamic performance by manual work. However, this procedure is time-consuming and depends on the human experience. In this paper, we defined retained theoretical leading/trailing edge as the reconstruction area. To accelerate the reconstruction process, an anchor-free neural network model based on Transformer was proposed, named LETR (Leading/trailing Edge Transformer). LETR extracts image features from an aspect of mixed frequency and channel domain. We also integrated LETR with the newest meta-Acon activation function. We tested our model on the self-made dataset LDEG2021 on a single GPU and got an mAP of 91.9\%, which surpassed our baseline model, Deformable DETR by 1.1\%. Furthermore, we modified LETR’s convolution layer and named the new model after GLETR (Ghost Leading/trailing Edge Transformer) as a lightweight model for real-time detection. It is proved that GLETR has fewer weight parameters and converges faster than LETR with an acceptable decrease in mAP (0.1\%) by test results.

Community-level wastewater monitoring for severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) RNA has demonstrated useful correlation with both coronavirus disease 2019 (COVID-19) case numbers and clinical testing positivity. Wastewater monitoring on college campuses has demonstrated promising predictive capacity for the presence and absence of COVID-19 cases. However, to date, such monitoring has largely relied upon composite or grab samples and reverse transcription quantitative PCR (RT-qPCR) techniques, which limits the accessibility and scalability of wastewater monitoring. In this study, we piloted a workflow that uses tampons as passive swabs for collection and reverse transcription loop-mediated isothermal amplification (RT-LAMP) to detect SARS-CoV-2 RNA in wastewater. Results for the developed workflow were available same day, with a time to result following tampon swab collection of approximately three hours. The RT-LAMP 95% limit of detection (76 gene copies reaction-1) was greater than RT-droplet digital PCR (ddPCR; 3.3 gene copies reaction-1). Nonetheless, during a building-level wastewater monitoring campaign conducted in the midst of weekly clinical testing of all students, the workflow demonstrated a same-day positive predictive value (PPV) of 33% and negative predictive value (NPV) of 80% for incident COVID-19 cases. The NPV is comparable to that reported by wastewater monitoring using RT-qPCR. These observations suggest that even with lower analytical sensitivity the tampon swab and RT-LAMP workflow offers a cost-effective and rapid approach that could be leveraged for scalable same-day building-level wastewater monitoring for COVID-19.

Near-fault ground motions can cause severe damage to civil structures, including bridges. Safety assessment of these structures for near fault ground motion is usually performed through Non-Linear Dynamic Analyses, while faster methods are often used. IMPAb (Incremental Modal Pushover Analysis for Bridges) permits to investigate the seismic response of a bridge by considering the effects of higher modes, which are often relevant for bridges. In this work, IMPAb is applied to a bridge case study considering near-fault pulse-like ground motion records. The records were analyzed and selected from the European Strong Motion Database and the pulse parameters were evaluated. In the paper results from standard pushover procedures and IMPAb are compared with nonlinear Response-History Analysis (NRHA), considering also the vertical component of the motion, as benchmark solutions and incremental dynamic analysis (IDA). Results from the case study demonstrate that the vertical seismic action has a minor influence on the structural response of the bridge. Therefore IMPAb, which can be applied considering vertical motion, remains very effective conserving the original formulation of the procedure, and can be considered a well performing procedure also for near-fault events.

Energy-efficient microprocessors are essential for a wide range of applications. While near-threshold computing is a promising technique to improve energy efficiency, optimal supply demands from logic core and on-chip memory are conflicting. In this paper, we perform static reliability analysis of 6T SRAM and discover the variance among different sizing configuration and asymmetric minimum voltage requirements between read and write operations. We leverage this asymmetric property in near-threshold processors equipped with voltage boosting capability by proposing an opportunistic dual-supply switching scheme with a write aggregation buffer. Our results show that proposed technique improves energy efficiency by more than 21.45% with approximate 10.19% performance speed-up.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

Shaped surfaces are increasingly used in the field of mould making for casting or injection moulding, where future products include shapes with different curvatures. These are surfaces that form convex curves, concave curves, or a combination thereof. Given these machined surfaces, it is important to know the impact of the finishing strategies on these surfaces. This paper deals with the comparison of finishing milling strategies in the production of shaped surfaces and the analysis of different methods for the evaluation of surface topography, surface roughness and the evaluation of deviations. The material used for the experiments was AlCu4Mg aluminium alloy, and Constant Z, Spiral and Spiral circle strategies were chosen for the finishing strategies. The evaluation of surface topography and surface roughness was carried out at three different sample heights with respect to the tool contact with the machined surface. The results showed changes in the toolpaths due to the variation of the effective diameter of the tool cutter to the machined surface as well as the choice of strategy. To produce specimens with corresponding shapes in terms of topography, the Constant Z strategy was the most suitable, in which uniform toolpaths were obtained over the whole height of the sample.

Three-Dimensional reconstruction of the corneal surface provides a powerful tool for managing corneal diseases. This study proposes a novel method for reconstructing the corneal surface from elevation point clouds, using modal schemes capable of reproducing corneal shapes using surface polynomial functions. The multivariable polynomial fitting was performed using a non-dominated sorting multivariable genetic algorithm (NS-MVGA). Standard reconstruction methods using least-squares discrete fitting (LSQ) and sequential quadratic programming (SQP) were compared with the evolutionary algorithm-based approach. The study included 49 eyes of 49 patients (ages 11-63) sorted in two groups: control (33 eyes) and keratoconus (KC) (16 eyes). Tomographic information (Sirius, Costruzione Strumenti Oftalmici, Italy) was processed using Matlab. The goodness of fit for each method was evaluated using mean squared error (MSE), measured at the same nodes where the elevation data were collected. Polynomial fitting based on NS-MVGA improves MSE values by 86% compared to LSQ-based methods in healthy patients. Moreover, this new method improves aberrated surface reconstruction by 43% for Amsler-Krumeich (AK) Grade 1 keratoconus patients. Finally, significant improvements were also found in morpho-geometric parameters, such as asphericity and corneal curvature radii.

We present a numerical illumination model to calculate direct as well as diffuse or Hapke scattered radiation scenarios on arbitrary planetary surfaces. This includes small body surfaces such as main belt asteroids as well as e.g. the lunar surface. The model is based on the raytracing method. This method is not restricted to spherical or ellipsiodal shapes but digital terrain data of arbitrary spatial resolution can be fed into the model. Solar radiation is the source of direct radiation, wavelength-dependent effects (e.g. albedo) can be accounted for. Mutual illumination of individual bodies in implemented (e.g. in binary or multiple systems) as well as self-illumination (e.g. crater floors by crater walls) by diffuse or Hapke radiation. The model is validated by statistical methods. A χ2 test is undertaken to compare simnulated images with DAWN images acquired during the survey phase at small body 4 Vesta.

The calculation of the surface tension of ordinary organic and ionic liquids, based on a computer algorithm applying a refined group-additivity method, is presented. The refinement consists of a complete breakdown of the molecules into their constituting atoms, further distinguishing them by their immediate neighbour atoms and bond constitution. The evaluation of the atom-groups’ contributions was carried out by means of a fast Gauss-Seidel fitting method founded upon the experimental data of 1895 compounds from literature. The result has been tested for plausibility using a 10-fold cross-validation (cv) procedure. The direct calculation and the cv test proved the applicability of the present method by the close similarity and excellent goodness of fit R2 and Q2 of 0.9023 and 0.8821, respectively. The respective standard deviations are ±2.01 and ±2.16 dyn/cm. Some correlation peculiarities have been observed in a series of ordinary and ionic liquids with homologous alkyl chains which are illustrated and discussed in detail, exhibiting the limit of the present method.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

Nobel metal nanohole arrays have been used extensively in chemical and biological systems due to their fascinating optical properties. Gold nanohole arrays (Au NHAs) were prepared as surface plasmon polaritons (SPP) generators for the surface-enhanced sum-frequency generation (SFG) detection of 4-Mercaptobenzonitrile (4-MBN). The angle-resolved reflectance spectra revealed that the Au NHAs have three angle-dependent SPP modes and two non-dispersive localized surface plasmon resonance (LSPR) modes under different structural orientation angles (sample surface orientation). An enhancement factor of ~30 was achieved when the SPP and LSPR modes of the Au NHAs were tuned to match the incident visible (VIS) and output SFG, respectively. This multi-mode matching strategy provided flexible controls and selective spectral windows for surface-enhanced measurements, and was especially useful in nonlinear spectroscopy where more than one light beam involved. The structural orientation- and power-dependent performance demonstrated the potential of plasmonic NHAs in SFG and other nonlinear sensing applications, and provided a promising surface molecular analysis development platform.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

The ultimate analysis parameters including carbon (C), hydrogen (H), nitrogen (N), and oxygen (O) content in biomass was rarely found to be predicted by nondestructive tests until to date. In this research, we developed partial least squares regression (PLSR) models to predict the ultimate analysis parameters of chip biomass using near infrared (NIR) raw spectra of non-wood and wood samples from fast growing tree and agricultural residue and nine different traditional spectral preprocessing techniques. These techniques include first derivative (sd1), second derivative (sd2), constant offset, standard normal variate (SNV), multiplicative scatter correction (MSC), vector normalization, min-max normalization, mean centering, sd1 + vector normalization, and sd1 + MSC. Additionally, we employed a genetic algorithm (GA), successive projection algorithm (SPA), multi-preprocessing (MP) 5−range, and MP 3−range to develop a PLSR model for rapid prediction. A dataset consisting of 120 chip biomass samples was utilized for model development in which the samples was non-wood samples of 65-67% and wood samples was 33-35%, and the model performance were evaluated and compared. The selection of the optimum performing model was mainly based on criteria such as the coefficient of determination in the prediction set (R2P), root mean square error of the prediction set (RMSEP), and the ratio of prediction to deviation values (RPD). The optimal model for weight percentage (wt.%) of C was obtained using GA−PLSR, yielding R2P, RMSEP, and RPD values of 0.6954, 1.1252 wt.%, and 1.8, respectively. Similarly, for wt.% of O, the most effective model was obtained using the multi-preprocessing PLSR−5 range method with R2P of 0.7150, RMSEP of 1.3088 wt.%, and RPD of 1.9. For wt.% of N, the optimal model was obtained using the MP PLSR−3 range method, resulting in R2P, RMSEP, and RPD values of 0.6073, 0.1008 wt.%, and 1.6, respectively. However, wt.% of H model provided R2P, RMSEP, and RPD values of 0.5162, 0.2322 wt.%, and 1.5, respectively. Notably, the limit of quantification (LOQ) values for C, H, and O were lower than the minimum reference values used during model development, indicating a high level of sensitivity. However, the LOQ for N, exceeded the minimum reference value, implying the samples to be predicted by the model must be in the range of reference range in calibration set. By scatter plot analysis, the effect of combined non-wood and wood spectra of biomass chips on rapid prediction of ultimate analysis parameters using NIR spectroscopy was investigated. To include different species in a model, the species have to be not only in the different values of the constituents to make a wider range for robust model but also they must provide their trend line characteristics in the scatter plot i.e. correlation coefficient (R), slope and intercept (same slope and slope approached to 1 and intercept is same (no gap) and approached zero, high R approached to 1). The effect of the R, slope and intercept to obtain the better optimized model were studied. The results show that the different species affected model performance of each parameter prediction in a different manner and by scatter plot analysis which of these species were affecting the model negatively and how the model could be improved was indicated. This is the first time of the effect is studied by the principle of scatter plot.

The models of partial least squares (PLS) regression and artificial neural network (ANN) for evaluation of texture properties of cooked germinated brown rice (GBR) using the Fourier transform near infrared (NIR) spectra of uncooked whole grain combined with data separation methods, spectral pretreatment methods were investigated in this study. The ANN was outperformed in evaluation of hardness by back extrusion test of cooked GBR using the smoothing combined with standard normal variate pretreated NIR spectra in the range of 12,500-4,000 cm−1 of 188 whole grain samples where the calibration sample set was separated from prediction set by Kennard-Stone method where the best ANN model for hardness from hidden layers of 25 and 8 iteration time provided R2, r2, RMSEC, RMSEP, Bias and RPD of 0.9987, 0.9447, 0.1021 N, 0.7699 N, 0.0216 N and 4.3 respectively. The PLS regression of 64 sample KDML GBR group and 64 sample various variety GBR group, provided models for the hardness of the former and the toughness of the latter which developed by using 7506−5446.3, 4605.4−4242.9 cm−1 which included the amylose vibration band of 6834 cm−1 while toughness model was from 9403.8-6094.3 cm−1 where included 6834 and 8316 cm−1 vibration bands of amylose which influenced the texture of cooked rice. The PLS regression models for hardness and toughness were with the r2 of 0.85 and 0.82, and the RPD of 2.9 and 2.4, respectively. The ANN model for hardness of cooked GBR should be implemented to the practical use in GBR production factories for the quality assurance and further updating using more samples and several brands to obtain the robust models.

A Mw7.8 earthquake struck Turkey on February 6, 2023, causing severe casualties and economic losses. This paper investigates the characteristics of strong ground motion and seismogenic fault of the earthquake. We collected and processed the strong ground motion records of 379 stations using Matlab, SeismoSignal and Surfer software, and obtained the peak ground acceleration (PGA) contour map. We analyzed the near-fault effect, the fault locking segment effect and the trampoline effect of the earthquake based on the spatial distribution of PGA, the fault geometry and slip distribution. We found that the earthquake generated a very strong ground motion concentration effect in the near-fault area, with the maximum PGA exceeding 2000cm/s2. However, the presence of fault locking segments influenced the spatial distribution of ground motion, resulting in four significant PGA high-value concentration areas at a local dislocation, a turning point and the end of the East Anatolian Fault. We also revealed for the first time the typical manifestation of the trampoline effect in this earthquake, which was characterized by a large vertical acceleration with the positive direction significantly larger than the negative direction. This paper provides an important reference for understanding the seismogenic mechanism, damage mode, characteristics and strong earthquake law of Turkey earthquake.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

In this study, the partial least squares regression (PLSR) models were developed using no pre-processing, traditional preprocessing, multi-preprocessing 5 range, multi-preprocessing 3 range, genetic algorithm (GA), and successive projection algorithm (SPA) to assess the higher heating value (HHV) and ultimate analysis of grounded biomass for energy usage employing near-infrared (NIR) spectroscopy. A novel approach was utilized based on the assumption that using multiple pretreatment methods across different sections in the entire NIR wavenumber range would enhance the performance of the model. The performance of the model obtained from 200 biomass samples for HHV and 120 samples for ultimate analysis was compared, and the best model was selected based on the coefficient of determination of validation set, root mean square error of prediction, and the ratio of prediction to deviation values. Based on model performance results, the proposed HHV model from GA-PLSR, and the N and O models from the mul-ti-preprocessing PLSR 5 range method could be used for most applications, including research, whereas the C and H models from GA-PLSR performance is fair and applicable only for rough screening. The overall findings highlight that the multi-preprocessing 5-range method, which was attempted as a novel approach in this study to develop the PLSR model, demonstrated better accuracy for HHV, C, N, and O, improving by 4.1839%, 8.1842%, 3.7587%, and 35.9404%, respec-tively. Therefore, it can be considered a reliable and non-destructive alternative method for rap-idly assessing biomass properties for energy usage and can also be used effectively in biomass trading. However, due to the smaller number of samples used in the model development, more samples are needed to update the model for a robust application.

Phase imaging of biochemical samples has been demonstrated for the first time at the Infrared Microspectroscopy (IRM) beamline of the Australian Synchrotron using the usually discarded Near-IR (NIR) region of the synchrotron-IR beam. The synchrotron-IR beam at the Australian Synchrotron IRM beamline has a unique fork shaped intensity distribution as a result of the gold coated extraction mirror shape, which includes a central slit for rejection of the intense X-ray beam. The resulting beam configuration makes any imaging task challenging. For intensity imaging, the fork shaped beam is usually tightly focused to a point on the sample plane followed by a pixel-by-pixel scanning approach to record the image. In this study, a pinhole was aligned with one of the lobes of the fork shaped beam and the Airy diffraction pattern was used to illuminate biochemical samples. The diffracted light from the samples was captured using a NIR sensitive lensless camera. A rapid phase-retrieval algorithm was applied to the recorded intensity distributions to reconstruct the phase information corresponding to different planes. The preliminary results are promising to develop multimodal imaging capabilities at the IRM beamline of the Australian Synchrotron.

Gastroenteropancreatic neuroendocrine neoplasms (GEP NENs) are rare cancers consisting of neuroendocrine carcinomas (NECs) and neuroendocrine tumors (NETs), which have been increasing in incidence in recent years. Few cell lines and pre-clinical models exist for the study of GEP NECs and NETs, limiting the ability to discover novel imaging and treatment modalities. To address this gap, we isolated tumor cells from cryopreserved patient GEP NECs and NETs and injected them into the flanks of immunocompromised mice to establish patient-derived xenograft (PDX) models. Two of 6 mice developed tumors (NEC913 and NEC1452). Over 90% of NEC913 and NEC1452 tumor cells stained positive for Ki67. NEC913 PDX tumors expressed neuroendocrine markers such as chromogranin A (CgA), synaptophysin (SYP), and somatostatin receptor-2 (SSTR2) whereas NEC1452 PDX tumors do not express SSTR2. Exome sequencing revealed loss of p53 and RB1 in both tumors. To demonstrate an application of these novel NEC PDX models for SSTR2-targeted peptide imaging, the NEC913 and NEC1452 cells were bilaterally injected into mice. Near infrared-labelled octreotide was administered and fluorescent signal was specifically observed for the NEC913 SSTR2 positive tumors. These 2 GEP NEC PDX models serve as valuable resource for GEP NEN therapy testing.

Background: Maladaptive neuroplasticity related learned response in substance use disorder (SUD) can be ameliorated using non-invasive brain stimulation (NIBS); however, inter-individual variability needs to be addressed for clinical translation. Objective: Our first objective was to develop a hypothesis for NIBS for learned response in SUD based on competing neurobehavioral decision systems model. Next objective was to conduct computational simulation of NIBS of cortico-cerebello-thalamo-cortical (CCTC) loop in cannabis use disorder (CUD) related dysfunctional “cue-reactivity” – a closely related construct of “craving” that is a core symptom. Our third objective was to test the feasibility of our neuroimaging guided rational NIBS approach in healthy humans. Methods: “Cue-reactivity” can be measured using behavioral paradigms and portable neuroimaging, including functional near-infrared spectroscopy (fNIRS) and electroencephalogram (EEG), metrics of sensorimotor gating. Therefore, we conducted computational simulation of NIBS, including transcranial direct current stimulation(tDCS) and transcranial alternating current stimulation(tACS) of the cerebellar cortex and deep cerebellar nuclei(DCN), of the CCTC loop for its postulated effects on fNIRS and EEG metrics. We also developed a rational neuroimaging guided NIBS approach for cerebellar lobule (VII) and prefrontal cortex based on healthy human study. Results: Simulation study of cerebellar tDCS induced gamma oscillations in the cerebral cortex while tTIS induced gamma-to-beta frequency shift. Experimental fNIRS study found that 2mA cerebellar tDCS evoked similar oxyhemoglobin(HbO) response in-the-range of 5x10-6M across cerebellum and PFC brain regions (=0.01); however, infra-slow (0.01–0.10 Hz) prefrontal cortex HbO driven(phase-amplitude-coupling, PAC) 4Hz, ±2mA (max.) cerebellar tACS evoked HbO in-the-range of 10-7M that was statistically different (=0.01) across those brain regions. Conclusion: Our healthy human study showed the feasibility of fNIRS of cerebellum and PFC as well as fNIRS-driven ctACS at 4Hz that may facilitate cerebellar cognitive function via the frontoparietal network. Future work needs to combine fNIRS with EEG for multi-modal imaging.

Obstructive sleep apnea (OSA) is a common sleep disorder, and continuous positive airways pressure (CPAP) is the most effective treatment. Poor adherence is one of the major challenges in CPAP therapy. The recent boom of wearable optical sensors measuring oxygen saturation makes the at-home multiple-night CPAP titrations possible, which may essentially improve the adherence of CPAP therapy by optimizing its pressure in a real-life setting economically. We tested whether the oxygen desaturations (OD) measured in the arm muscle (arm_OD) by gold-standard frequency-domain multi-distance near-infrared spectroscopy (FDMD-NIRS) changes with titrated CPAP pressures in OSA patients together with polysomnography. We found that the arm_OD (2.08 ± 1.23%, mean ± standard deviation) was significantly smaller (P-value &lt;0.0001) than the fingertip OD (finger_OD) (4.46 ± 2.37%) measured by polysomnography pulse oximeter. Linear mixed-effects models suggested that CPAP pressure was a significant predictor for finger_OD but not for arm_OD. Since FDMD-NIRS measures a mixture of arterial and venous OD, whereas fingertip pulse oximeter measures arterial OD, our results of no association between arm_OD and finger_OD indicate that the arm_OD mainly represented venous desaturation. Arm_OD measured by near-infrared optical sensors may be not a suitable indicator of the effectiveness of CPAP titration.

A workplace sleep health promotion program was implemented in an Italian police unit from 2016 to 2017. Of the 242 police officers in the unit, 218 (90%) agreed to take part in the program. A crossover trial was made in which the police officers were divided into two groups that performed sleep health promotion activities in the first and second year, respectively. The first group of officers showed significant sleep improvements at the end of the first year, while the second group had similar or worse parameters than at baseline. At follow-up, a significant improvement in the quantity and quality of sleep was reported in both groups. Sleep improvements at follow-up were associated with a marked reduction in the frequency of accidents at work and near-misses. All sleep parameters showed a significant association with injuries and near-misses in univariate logistic regression analyses. Before the intervention, sleepiness was the best predictor of injuries (aOR 1.220; CI95% 1.044-1.426) and near-misses (aOR 1.382; CI95% 1.182-1.615). At follow-up, when sleep conditions had improved, insomnia symptoms were the most significant predictors of work accidents (aOR 13.358; CI95% 2.353-75.818). Sleep health promotion can be useful in police officers.

The Solvency II regulatory framework specifies procedures and parameters for determining solvency capital requirements (SCRs) for insurance companies. The proposed standard SCR calculations involve two steps. The Value–at–Risk (VaR) of each risk driver is measured and, in a second step, all components are aggregated to the company’s overall SCR, using the Standard Formula. This formula has two inputs: the VaRs of the individual risk drivers and their correlations. The appropriate calibration of these input parameters has been the purpose of various Quantitative Impact Studies that have been conducted during recent years. This paper demonstrates that the parameter calibration for the equity–risk module—overall, with about 25%, the most significant risk component—is seriously flawed, giving rise to spurious and highly erratic parameter values. As a consequence, an implementation of the Standard Formula with the currently proposed calibration settings for equity–risk is likely to produce inaccurate, biased and, over time, highly erratic capital requirements.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

Eastern boundary upwelling systems feature strong zonal gradients of physical and biological ocean properties between cool, productive coastal oceans and warm, oligotrophic subtropical gyres. Zonal currents and jets (striations) are therefore likely to contribute to the transport of water properties between coastal and open oceanic regions. Multi-sensor satellite data are used to characterize the signatures of striations in sea surface temperature (SST), salinity (SSS), and chlorophyll-a (Chl-a) in subtropical eastern North/South Pacific (ENP/ESP) upwelling systems. In the ENP, tracers exhibit striated patterns extending up to ~2500 km offshore. Striations in SST and SSS are highly correlated with quasi-zonal jets, suggesting that these jets contribute to SST/SSS mesoscale patterns via zonal advection. Chl-a striations are collocated with sea surface height (SSH) bands, a possible result of mesoscale eddy trains trapping nutrients and forming striated signals. In the ESP, striations are only found in SST and coincide with SSH bands, consistently with quasi-zonal jets located outside major zonal tracer gradients. An interplay between large-scale SST/SSS advection by the quasi-zonal jets, mesoscale SST/SSS advection by the large-scale meridional flow and eddy advection may explain the persistent ENP hydrographic striations. These results underline the importance of quasi-zonal jets for surface tracer structuring at the mesoscale.

Management practices must be developed to improve yam production sustainability. Image-based phenotyping techniques could help developing such practices based on non-destructive analyses of important plant traits. Our objective was to determine the potential of image-based phenotyping methods to assess traits relevant for tuber yield formation in yam grown in glasshouse and field. We took plant and leaf pictures with consumer cameras. We used the numbers of image pixels to derive the shoot biomass and the total leaf surface and calculated the ‘triangular greenness index’ (TGI) which is an indicator of the plant nitrogen (N) nutritional status. Under glasshouse conditions, the number of pixels obtained from nadir view (image taken top down) was positively correlated to the shoot biomass, and the total leaf surface, while the TGI was negatively correlated to the N content of diagnostic leaves. Under field conditions, pictures taken from the nadir view showed an increase in soil surface cover and a decrease in TGI with time. TGI was negatively correlated to SPAD measured on specific leaves but was not correlated to the N content of these leaves. In conclusion, these phenotyping techniques deliver relevant results but need to be further developed and validated for application in yam.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

In this study, Fe-Mo-B based hardfacing electrodes containing different amounts of Mo were coated on an AISI 1020 steel substrate using the electric arc welding method. The findings show that molybdenum is highly effective on the microstructure and minor changes in the coating composition affect the phases and morphological properties. In the hardness tests, an increase of 73% was achieved in the Fe14Mo2B4 based hardfacing coating compared to the base material and a 30% increase compared to the Fe16B4 based coating. The highest macro hardness value was measured as 56.4 HRC and the highest phase hardness was measured as 3228 HV in the FeMo2B2 phase. The lowest wear rate was measured in the Fe14Mo2B2 based coating. The wear rate of the Fe14Mo2B4 based coating was 8.1 times lower than that of the substrate material and 4.7 times lower than that of the Fe16B4 based coating. According to corrosion test results, the highest corrosion resistance was obtained in Fe16B4 based coating. The current density value of the Fe16B4 based coating was measured to be 13.6 times lower than that of the substrate material.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Coalescence of nanowires and other three-dimensional structures into continuous film is desirable for growing low dislocation density III-nitride and III-V materials on lattice-mismatched substrates, and interesting from the fundamental viewpoint. Here, we develop a growth model for vertical nanowires which, under rather general assumptions on the solid-like coalescence process within the Kolmogorov crystallization theory, results in a morphological diagram for the asymptotic coverage of a substrate surface. The coverage is presented as a function of two variables, the material collection efficiency on the top nanowire facet a, and the normalized surface diffusion flux of adatoms from the NW sidewalls b. The full coalescence of nanowires is possible only when a=1 regardless of b. At a&gt;1, which is usual for vapor-liquid-solid growth with a catalyst droplet, nanowires can only partly merge but never coalesce into continuous film. These results can be used for predicting and controlling the degree of surface coverage by nanowires and three-dimensional islands by tuning the surface density, droplet size, adatoms diffusivity, and geometry of the initial structures in the vapor-liquid-solid, selective area or self-induced growth processes in different epitaxy techniques.

At the nanoscale, metals exhibit special electrochemical and optical properties, which play an important role in nanobiosensing. In particular, the surface plasmon resonance based on precious metal nanoparticles, as a kind of tag free biosensor technology, has brought high sensitivity, high reliability and convenient operation to the sensor detection. By applying an electrochemical excitation signal on the nano plasma device, modulating its surface electron density and realizing electrochemical coupling surface plasmon resonance, it can effectively complete the joint transmission of electrical signals and optical signals, increase the resonance shift of the spectrum, and further improve the sensitivity of the designed biosensor. In addition, smartphone is playing an increasingly important role in portable mobile sensor detection systems. These systems typically connect sensing devices to smartphone to perceive different types of information, from optical signals to electrochemical signals, providing ideas for the portability and low-cost design of these sensing systems. Among them, electrochemiluminescence, as a special electrochemical coupled optical technology, has good application prospects in mobile sensing detection due to its strong anti-interference ability, which is not affected by background light. In this review, the surface plasmon resonance is introduced from nanoparticles, and its response process is analyzed theoretically. Then, the mechanism and sensing application of electrochemistry coupled surface plasmon resonance and electrochemiluminescence are emphatically introduced. Finally, it extends to the related research of electrochemical coupled optical sensing on mobile detection platforms.

The surface fluorination of polypropylene (PP) was performed using F2 and O2 gas mixtures with different F2 gas proportions at 25 °C and 13.3 kPa for 1 h. The surface roughness of the fluorinated PP samples was approximately 1.5 times higher than that of the untreated sample (5 nm). The Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results showed that the PP-derived bonds (-C-C- and -CHx) decreased because they were converted into polar groups (-C–O, -CHF-, and -CFx), which increased the surface electronegativity of PP. The variation in the F2 gas proportion in the gas mixture significantly affected the hydrophilicity and surface composition of PP. At F2 gas proportions of <70%, the hydrophilicity of the fluorinated PP samples improved. Notably, the hydrophilic and negatively charged PP surface enhanced the dyeing of the polymer with basic methylene blue (MB). In contrast, at F2 gas proportions of >90%, the PP surface became hydrophobic owing to increased hydrophobic -CF3 bonds. Thus, enhanced PP dyeing can be controlled based on the composition of the F2 and O2 gas mixture.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Sea ice surface roughness affects ice-atmosphere interactions, serves as an indicator of ice age, shows patterns of ice convergence and divergence, affects the spatial extent of summer melt ponds, and ice albedo. We have developed a method for mapping sea ice surface roughness using angular reflectance data from the Multi-angle Imaging SpectroRadiometer (MISR) and lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). Using an empirical data modeling approach, we derived estimates of Arctic sea ice roughness ranging from centimeters to decimeters meters within the MISR 275-m pixel size. Using independent ATM data for validation, we find that histograms of lidar and multi-angular roughness values are nearly identical for areas with roughness <20 cm but that for rougher regions, the MISR-derived roughness has a narrower range of values than the ATM data. The algorithm is able to accurately identify areas that transition between smooth and rough ice. Because of its coarser spatial scale, MISR-derived roughness data have a variance of about half that ATM roughness data.

Wetting of deformable substrates has gained significant interest over the past decade due to its extensive applications and uses. This interest has developed due to technological advances which are able to capture interfacial behavior taking place when a liquid droplet is placed on a deformable substrate. Researchers have developed different theories to explain processes taking place in the process of wetting of deformable/soft substrates. For the scope of this review, we will consider the fluid to be Newtonian, partially wetting, and surface forces are incorporated with the help of disjoining/conjoining pressure acting in the vicinity of the apparent, three-phase contact line. The following subjects are briefly reviewed: (i) Equilibrium of droplets on soft substrates. It is shown that properties of the disjoining/conjoining pressure isotherm and properties of the deformable substrate determine both the shape of the liquid droplet and deformation of the substrate; (ii) Equilibrium conditions of droplets on deformable substrates. It is shown that for a droplet to be at equilibrium on a deformable substrate under consideration, Jacobi’s sufficient condition is satisfied; (iii) Hysteresis of contact angle of sessile droplets on deformable substrates. It is shown that as the elasticity of the deformable substrate is increased, both advancing and receding contact angles are reduced.

The influence of the film thickness and the substrate’s refractive index on the surface mode at the superstrate is an important study step that may help clearing some of the misunderstandings surrounding their propagation mechanism. A single sub-wavelength slit perforating a thin metallic film is among the simplest nanostructure capable of launching Surface Plasmon Polaritons on its surrounding surface when excited by an incident field. Here, the impact of the substrate and the film thickness on surface waves is investigated. When the thickness of the film is comparable to its skin depth, SPP waves from the substrate penetrate the film and emerge from the superstrate, creating a superposition of two SPP waves, that leads to a beat interference envelope with well-defined loci which are the function of both the drive frequency and the dielectric constant of the substrate/superstrate. As the film thickness is reduced to the SPP’s penetration depth, surface waves from optically denser dielectric/metal interface would dominate, leading to volume plasmons that propagate inside the film at optical frequencies. Interference of periodic volume charge density with the incident field over the film creates charge bundles that are periodic in space and time.

The aim of the present study was to monitor implant stability after sinus floor elevation with two biomaterials during the first 6 months of healing by a resonance frequency analysis (RFA), and how physico-chemical properties affect the implant stability quotient (ISQ) at the placement and healing sites. Bilateral maxillary sinus augmentation was performed in 10 patients in a split-mouth design using a bobine HA (BBM) as a control and porcine HA (PBM). Six months after sinus lifting, 60 implants were placed in the posterior maxilla. The ISQ was recorded on the day of surgery from RFA at T1 (baseline), T2 (3 months), and T3 (6 months). Statistically significant differences were found in the ISQ values during the evaluation period. The ISQ (baseline) was 63.8±2.97 for BBM and 62.6±2.11 for PBM. The ISQ (T2) was ~ 73.5±4.21 and 67±4.99, respectively. The ISQ (T3) was ~ 74.65±2.93 and 72.9±2.63, respectively. All the used HAs provide osseointegration and statistical increases in the ISQ at baseline, T2 and T3 (follow-up), respectively. The BBM, sintered at high temperature with high crystallinity and low porosity, presented higher stability, which demonstrates that variations in the physico-chemical properties of a bone substitute material clearly influence implant stability.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

Giant plasmonic surface enhancement has been observed in gold coated micron sized inverse pyramids entrapping a gold nanoparticle. The amplification of both surface enhanced Raman and photoluminescence signals was found to be dependent on the diameter of trapped gold nanoparticle and around 50-fold enhancement was detected for 250nm diameter sample relatively to the 50nm one. Finite differential time domain simulations, performed to determine the near-field distribution in the structure, showed that when the nanoparticle protrudes into the hotspot zone of the void, coupling of electromagnetic field occurs and the plasmon-related near-field enhancement is concentrated into the close vicinity of the nanoparticle, mainly into the close gaps around the tangential points of the curved sphere and the flat pyramid surface. This results in a more than 15 times increase of the near-field intensity, compared to the empty void.

Managing sidelobe levels (SLLs) in metasurface-driven beam-steering antennas poses a significant challenge due to intrinsic factors leading to grating lobes. Our proposed method employs an equivalent model to optimize large periodic metasurfaces efficiently. This model predicts complete metasurface performance, accounting for mutual coupling between patches. We introduce an evolutionary optimization algorithm based on the Cross Entropy (CE) method to enhance PGM-based beam-steering antennas and suppress sidelobes. Two strategies were employed: first is to optimize the patch dimensions for a sidelobe-free pattern and the second is to maintain the PGM dimensions while optimizing feed array amplitudes. Both strategies effectively suppressed sidelobes, offering insights into the CE method's applicability and effectiveness for CPU-intensive electromagnetic optimization challenges. The proposed CE method variant retains its simplicity while improving monitoring capabilities, addressing this limitation. Smaller generations yield better improvements per evaluation

The effect of stress on task performance is complex, too much or too little negatively affects performance; and there exists an optimal level of stress to drive optimal performance. Task difficulty and external affective factors are distinct stressors that impact cognitive performance. Neuroimaging studies showed that mood affects working memory performance and the correlates are changes in haemodynamic activity in the prefrontal cortex (PFC). We investigate the interactive effects of affective states and working memory load (WML) on working memory task performance and haemodynamic activity using functional near-infrared spectroscopy (fNIRS) neuroimaging on the PFC of healthy participants. We seek to understand if haemodynamic responses could tell apart workload related stress from situational stress arising from external affective distraction. We found that the haemodynamic changes towards affective stressor and workload related stress were more dominant in the medial and lateral PFC respectively. Our study reveals distinct affective state-dependent modulations of haemodynamic activity with increasing WML in n-back tasks, which correlate with decreasing performance. The influence of negative affect on performance is greater at higher WML, and haemodynamic activity showed evident changes in temporal, and both spatial and strength of activation differently with WML.

This study sought to investigate steel frames’ performance with dual lateral loader system (Frame bending + bracings of divergent and convergent) in near and far filed to fault. In order to this, four categories of steel frame with dual system with 8, 10 and 12 story are designed with average formation based on existing seismic regulation in 2800 standard of Iran and tenth chapter of national regulations of construction (planning and performing steel construction). Time history non-linear dynamic analysis under the effect of near and far field earthquakes has been done on plan’s models. Then the maximum of floors’ dislocation, floors’ drift, roof dislocation, base shear and energy curves of frames are shown and compared with each other. All non-linear time history analyses have been accomplished using PERFORM 3D software.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

A finite-type immersion or smooth map is a nice tool to classify submanifolds of Euclidean space, which comes from eigenvalue problem of immersion. The notion of generalized 1-type is a natural generalization of those of 1-type in the usual sense and pointwise 1-type. We classify ruled surfaces with generalized 1-type Gauss map as part of a plane, a circular cylinder, a cylinder over a base curve of an infinite type, a helicoid, a right cone and a conical surface of $G$-type.

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

Steel construction is used more often these days as an alternative to the R.C.C. when light weight, high strength, large-span structures with a faster erection are required. Extensive studies have been done by researchers to study the seismic performance of reinforced concrete and steel structures, both in terms of elastic and inelastic behavior. Composite construction is also a recent advancement in the building industry with similar advantages. However, no emphasis has been given to the comparison between the inelastic behavior of steel and composite structures when subjected to lateral loads. This study compares the inelastic behavior of steel and a composite frame designed to have the same plastic moment capacity for structural members. The responses, such as the formation of hinges, story drifts, story displacements, lateral stiffness, ductility, maximum strength, energy dissipated, joint accelerations, and performance points, are compared with the aid of the building analysis and design software ETABS-18. For this, response spectrum analysis, pushover analysis and nonlinear direct integration time history analysis have been performed on both frames. For design and analysis, international codes such as IS 800-2007, IS 875 (Part I, II, IV), IS 1893-2002, AISC 360 (16 &amp; 10) and FEMA 440 have been used. Part of this study also aims at comparing the response of these frames when subjected to near field and far field earthquakes. It can be concluded from the results that the post yield performance of the composite frame is superior to that of the steel frame when seismically excited.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

The high reactivity of acetylene group the formation of strong chemical bonds with active sites on mineral surfaces, thereby improving the flotation performance of gold minerals. This study utilized Density Functional Theory (DFT) to analyse the quantum chemical parameters of structure, Mulliken population, and the frontier orbitals of a thioester collector containing an acetylene group, PDEC (prop-2-yn-1-yl diethylcarbamodithioate). PDEC is compared with analogous thioester collectors Z-200 and Al-DECDT, and the interaction mechanism of PDEC on the Au(1 1 1) surface is simulated, followed by empirical validation through adsorption experiments. The findings indicate that S atom of PDEC in the carbon-sulfur group exhibit shorter covalent bond lengths, and reduced carbon-sulfur double bonds and Mulliken population, resulting in enhanced electron localization. This confers greater selectivity to PDEC during its adsorption on mineral surfaces. Frontier orbital analysis shows that the electrons of acetylene group possess a notable electron-accepting capacity, significantly influencing frontier orbital energy of PDEC and playing a pivotal role in the bonding interaction with mineral surfaces. Both the S atom in carbon-sulfur group and its acetylene group establish stable adsorption structures with the A(111) surface in a single coordination mode. The adsorption energy sequence is PDEC > Al-DECDT > Z-200. Partial density of states demonstrates that S 3p orbit of carbon-sulfur group hybridize with Au 5d orbit, while the C 2p orbit of the acetylene group engage in weaker back-donation bonding with Au 5d orbit. This is corroborated by electron density difference and post-adsorption Mulliken population analyses, revealing that S atom of carbon-sulfur group in PDEC donate electrons to Au atom, forming dominant positive coordination bonds, whereas the acetylene group accepts partial electrons from Au atom, resulting in weaker back-donation bonds. The adsorption experiments align with the DFT adsorption energy results.

Surface Plasmon Resonance (SPR) technology has been known as a powerful tool for studying biomolecular interactions because it offers real-time and label-free multiparameter analysis with high sensitivity. This article summarizes the results that have been obtained from the use of SPR technology in studying the dynamics of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) mutations. This paper will begin by introducing the working principle of SPR and the kinetic parameters of the sensorgram which include the association rate constant (ka), dissociation rate constant (kd), equilibrium association constant (KA), and equilibrium dissociation constant (KD). At the end of the section, we will summarize kinetic data on the interaction of SARS-CoV-2 with different variants with various ligands which were obtained from the results of SPR signal analysis. These affinity-related kinetic data are very useful both in drug discovery for therapeutic purposes and in the detection of SARS-CoV-2.

Proteins in the crowded environment of human cells have often been studied regarding nonspecific interactions, misfolding, and aggregation, which may cause cellular malfunction and disease. Specifically, proteins with high abundance are more susceptible to these issues due to the law of mass action. Therefore, the surfaces of highly abundant cytoplasmic (HAC) proteins directly exposed to the environment can exhibit specific physicochemical, structural, and geometrical characteristics that reduce nonspecific interactions and adapt to the environment. However, the quantitative relationships between the overall surface descriptors still need clarification. Here, we used machine learning to identify HAC proteins using hydrophobicity, charge, roughness, secondary structures, and B-factor from the protein surfaces and quantify the contribution of each descriptor. First, several supervised learning algorithms were compared to solve binary classification problems for the surfaces of HAC and extracellular proteins. Then, logistic regression was adopted for the feature importance analysis of descriptors considering model performance (80.2% accuracy and 87.6% AUC) and interpretability. The HAC proteins showed positive correlations with negatively and positively charged areas but negative correlations with hydrophobicity, B-factor, beta structure proportion, roughness, and disordered regions proportion. Finally, the details of each descriptor could be explained concerning adaptative surface strategies of HAC proteins to regulate nonspecific interactions, protein folding, flexibility, stability, and adsorption. This study presented a novel approach using various surface descriptors to identify HAC proteins and provided quantitative design rules for the surfaces well-suited to human cellular crowded environments.

In order to improve the wear resistance of copper contacts in high-voltage switches and improve the abnormal discharge phenomenon caused by wear gaps, laser remelting technology was used to strengthen the surface of copper contacts. The surface morphology, microhardness, and wear resistance of the remelted samples were tested and characterized using scanning electron microscopy (SEM), microhardness tester, and friction and wear tester. The test results indicate that laser frequency, pulse width, and current parameters can directly affect the surface morphology and wear resistance of the sample, but their influencing processes vary. The laser frequency is achieved by the variation of the superposition relationship between the impact points, while the pulse width and current are achieved by the variation of the laser intensity at the impact points. When the pulse frequency is 10Hz, the pulse width is 10ms, and the current is 100A, the sample exhibits a more balanced surface morphology, microhardness, and wear resistance.

Environmental perception is a powerful tool for identifying community needs and potential within their surroundings. This study assessed tourists' environmental perception regarding solid waste and its impact on the Hurtado balneary, located in Valledupar, Colombia. From May to July 2023, the investigation delved into the environmental attitudes and behaviors of 769 balneary users by employing a combination of observation, photographic documentation, and a comprehensive 21-question online survey. The findings unveiled compelling insights: an overwhelming 98.8% of participants acknowledged the adverse effects of solid waste on the environment, with an impressive 98% demonstrating a willingness to participate in waste management efforts. Alarmingly, 42.13% exhibited limited awareness of waste management practices, reflecting a lack of public interest and commitment (41.61%). Statistically significant disparities emerged: 59% of waste items were not appropriately disposed of in designated receptacles. Reasons for this included a lack of a sense of belonging (50.2%) and inadequate environmental education (45.6%). 96% expressed the need for river conservation signage, while 59.8% had not engaged in environmental training. The implications of these results extend beyond the Hurtado balneary, potentially informing solid waste management strategies in other aquatic environments. Furthermore, this investigation aligns with three critical Sustainable Development Goals: SDG 12, emphasizing responsible consumption and production; SDG 13, addressing climate action; and SDG 15, advocating for life on land and below water. Keywords: Tourism; solid waste; surface water; environmental management.

Cardiovascular diseases continuing to be a major contributor to illness and death on a global scale and the implementation of stents has given rise to a revolutionary transformation in the field of interventional cardiology. The thrombotic and restenosis complications associated with stent implantation pose ongoing challenges. In recent years, bioactive coatings have emerged as a promising strategy to enhance stent hemocompatibility and reduce thrombogenicity. This review article provides an overview of the surface engineering techniques employed to improve the hemocompatibility of stents and reduce thrombus formation. It explores the mechanisms underlying thrombosis and discusses the factors influencing platelet activation and fibrin formation on stent surfaces. Various bioactive coatings, including anticoagulant agents, antiplatelet agents, and surface modifications, are discussed in detail, highlighting their potential in reducing thrombogenicity. Evaluation methods for assessing hemocompatibility and thrombogenicity are also reviewed, ranging from in vitro assays to animal models. Recent advances in the field, such as nanotechnology-based coatings and bioactive coatings with controlled drug release systems, are highlighted. Surface engineering of bioactive coatings holds great promise for enhancing the long-term outcomes of stent implantation by enhancing hemocompatibility and reducing thrombogenicity. Future research directions and potential clinical applications are discussed, underscoring the need for continued advancements in this field.

Titanium (Ti) and Ti-based alloys are commonly used in dental implants, and surface modifications of dental implants are important for achieving osseointegration (i.e., direct connection between the implant surface and bone). This study investigated the effect of an eco-friendly etching solution—a hydrogen peroxide–sodium bicarbonate mixture—on the surface properties and contact angles of and osteoblast adhesion and proliferation on Ti surfaces. Disk-shaped Ti specimens were prepared using different surface treatments (machining, sandblasting, and sandblasting/acid-etching), and they were immersed in the etching solution and then ultrasonically cleaned. Surface characterization was performed using scanning electron microscopy, digital microscopy, contact angle analysis, and X-ray photoelectron spectroscopy. MG-63 osteoblasts were cultured on the specimens, and their adhesion to the specimen surface and their proliferation were examined using staining and the MTT assay, respectively. Additional etching with the etching solution caused the formation of nano/micro hierarchical structures, increased the surface roughness, and enhanced the hydrophilicity. Osteoblast adhesion and proliferation were found to improve on the modified surfaces. The eco-friendly etching method has the potential to enhance the biological properties of Ti implant surfaces and to thereby improve the dental implant performance.

Nowadays, the world's refractory gold ore production accounts for about 30% of the world's total gold, such gold concentrate leaching rate is low, seriously limiting the efficient use of gold resources. The alkaline preoxidation process can improve the leaching rate of this kind of gold deposit, and has a good development and application prospect. So, it is of great significance to study the oxidation and dissolution behavior of pyrite in alka-line environment. In this paper, the oxidation process of gold-bearing pyrite in alkaline electrolyte was studied by electrochemical techniques, and the oxidation products of pyrite electrode in alkaline solution were characterized by XPS，SEM and other analytical methods. The results show that the optimum pH for pyrite electrochemical oxidation dissolution is about 12, and oxidation potential of pyrite should be above 0.8 V. In that proces of alkaline oxidation dissolution of pyrite, part of S element enters the electrolyte in the form of Sx2-, S2O32-, SO32-and SO42-, and a small amount of S element is adsorbed on the surface of the electrode in the form of S0 and becomes a part of the passive layer. Fe element is adsorbed on the surface of electrode in the form of Fe(OH)2, Fe2O3 and Fe2(SO4)3, which becomes the main component of passivation layer. This study provides a theoretical basis and reference data for the chemical preoxidation treatment of sulfide ores.

This study compares the action of different handpieces (turbine, high-speed electric handpiece and piezoelectric device) on surface roughness of enamel and dentin when using diamond-coated working tips and burs of the same grit size. Experiment was conducted on 15 extracted first molars from patients aged 45 to 60 years. The occlusal portion was removed using a diamond-coated water wheel and then refined with a 120-130 μm grit bur in order to obtain a flat surface with an adequate exposition of the dentin core. Each surface was divided into three portions and every portion was finished with one of the three tested instruments. Rotary burs and piezoelectric tips had the same grit size (60 μm) and load on handpiece during preparation never exceeded 150 g. Surface roughness parameters (Ra, Rsk, Rku) were recorded with an optical profilometer and SEM analysis of treated surfaces and working tips was conducted. Ra and Rsk differed significantly between enamel and dentin only after using turbine (p=0.004 and p=0.007, respectively). No significant differences were observed in Ra, Rsk, and Rku between enamel and dentin when using high-speed electric handpiece or piezoelectric device. Turbine produced higher Ra and Rsk values on dentin than the other devices, while no significant differences were found between piezoelectric handpiece and high-speed electric contra-angle on both substrates. Summarizing, the findings of the present study demonstrated that turbine generated rougher surfaces on dentin compared to the other handpieces. Moreover, the turbine produced more asymmetrical surface profiles on both enamel and dentin. However, it should be considered that these differences in roughness (Ra) were within the range of 0.25-0.30 μm: it is still unclear if these variations, although statistically significant, will influence final clinical outcomes.

Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

The rowing technique is a key factor in the overall rowing performance. Nowadays the athletes’ performance is so advanced that even small differences in technique can have an impact on sport competitions. To further improve the athletes’ performance, individualized rowing is necessary. This can be achieved by intelligent measurement technology that provides direct feedback. To address this issue, we developed a novel wireless rowing measurement system (WiRMS) that acquires rowing movement and measures muscle activity using electromyography (EMG). Our measurement system is able to measure several parameters simultaneously: the rowing forces, the pressure distribution on the scull, the oar angles, the seat displacement and the boat acceleration. WiRMS was evaluated in a proof-of-concept study with seven experienced athletes performing a training on water. Evaluation results showed that WiRMS is able to assess the rower’s performance by recording the rower’s movement and force applied to the scull. We found significant correlations (p&lt;0.001) between stroke rate and drive-to-recovery ratio. By incorporating EMG data, a precise temporal assignment of the activated muscles and their contribution to the rowing motion was possible. Furthermore, we were able to show that the rower applies the force to the scull mainly with the index and middle fingers.

The access road to the powerhouse's hydraulic system's facilities in Guarumales (Azuay, Ecuador) presents a medium-sized landslide. Geophysical tests were conducted in the initial research stage, combining electrical and seismic methods. A SEV and HVSR surveys campaign have been taken as a reference for the analysis of the landslide area. The distribution of these test points has been at three different levels along the landslide where the access road crosses it and trying to cover the area's most extensive possible length and width. In the area, we find the geology dominated by the presence of schists, altered to different degrees and presenting blocks of material with a lower degree of alteration within colluvium formed by a clayey matrix and coarse material of the exact nature. There is also evidence of surface and groundwater in the area. The results obtained through SEV tests have allowed for defining the separation zone of the mobilized or sliding materials compared to the fixed or immobile ones (potentially, the sliding surface was marked). Using the HVSR technique, the natural vibration frequencies of the ground associated with the sliding mass (separation of seismic impedances between a two-layer model: mobile and fixed) have been determined. Previous authors proposed an empirical relationship establishing the exponential relationship, already proposed by previous authors, between sediment thickness and natural frequencies. It has been possible to determine the depth of the position of the loosely compacted sediment zone (and probably moving or mobilized) compared to that of compact materials (immobile) and thereby define the potential rupture surface.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

Sea ice roughness can serve as a proxy for other sea ice characteristics such as ice thickness and ice age. Arctic-wide maps that represent spatial patterns of sea ice roughness can be used to better characterize spatial patterns of ice convergence and divergence processes. Sea ice surface roughness can also control and quantify turbulent exchange between sea ice surface and atmosphere and therefore influence surface energy balance at the basin scale. We have developed a data processing system that produces georeferenced sea ice roughness rasters that can be mosaicked to produce Arctic-wide maps of sea ice roughness. This approach starts with Top-of-Atmosphere radiance data from the Multi-angle Imaging SpectroRadiometer (MISR). We used red-band angular data from three MISR cameras (Ca, Cf, An). We created a training data set in which MISR pixels were matched with co-located and concurrent lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). We used a K-nearest neighbor algorithm with the training data to calibrate the multi-angle data to values of surface roughness and then applied the algorithm to Arctic-wide MISR data for two 16-day periods in April (spring) and July (summer). After georeferencing the roughness rasters, we then mosaicked each 16-day roughness dataset to produce Arctic-wide maps of sea ice roughness for spring and summer. Assessment of the results shows good agreement with independent ATM roughness data, not used in model development. A preliminary exploration of spatial and seasonal changes in sea ice roughness for two locations shows the ability to characterize the roughness of different ice types and the results align with previous studies. This processing system and its data products can help the sea ice research community to gain insights into the seasonal and interannual changes in sea ice roughness over the Arctic.

Due to the extremely inert surface of the polyester (PET) fabric, a toxic and traditional resorcinol-formaldehyde-latex (RFL) dipping solution is always needs to be used in in rubber composite industry. Unfortunately, other effective methods for fabric surface treatment are in urgent needed to improve the poor bonding interface between the fabric and the rubber matrix. In our study, a facile way to modify PET fabric was developed. Specifically, the fabric is treated by an alkaline solution and a coupling agent with magnetic agitation. Afterwards, the treated fabric/rubber composites are prepared through a co-vulcanization process. Attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR), thermogravimetric analysis (TGA) were used to characterize the surface chemical compositions of the modified fabrics. The adhesion behavior is analyzed by the peel test. The results show that the fabric surface is successfully grafted with a coupling agent, and the peel strength reaches 9.8 N/mm after KH550 treatment, which is increased 32% compared with that of the original fabric/rubber composites. In addition, the vulcanization rate and interfacial fracture mechanism are also researched.

In this study we present gas-phase fluorination as a method to create a thin LiF layer on Li6.5La3Zr1.5Ta0.5O12 (LLZTO). We compare these fluorinated films with LiF films produced by RF-magnetron sputtering, where we investigated the interface between the LLZTO and the deposited LiF showing no formation of a reaction layer. Furthermore, we investigate the ability of this LiF layer as a protection layer against Li2CO3 formation in ambient air. By this we show that Li2CO3 formation is absent at the LLZTO surface after 24 h in ambient air supporting the protective character of the formed LiF films and hence could enhance the handling of LLZTO in air for battery production. With respect to the use within hybrid electrolytes consisting of LLZTO and a mixture of polyethylene oxide (PEO) and Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) we also investigated the interface between the formed LiF films and a mixture of PEO LiTFSI by X-ray photoelectron spectroscopy (XPS) showing decomposition of the LiTFSI at the interface.

Terzaghi proposed two-dimensional (2D) arching theory through trapdoor tests based on the assumption of a vertical slip surfaces. However, the original 2D assumption is different from a real three-dimensional (3D) excavation condition and an actual slip surfaces caused by downward movement of a trapdoor is an inclined surface. Therefore, a 3D theoretical model was proposed in this study considering inclined slip surfaces. Horizontal thin layer differential element method was used to obtain the loosening soil pressure. Using the 3D theoretical model, the effects of buried depth ratio of loose area, length of loose area, soil parameters, and lateral earth pressure coefficient were investigated. The loosening earth pressure was highly affected by inclination angle of slip surface, buried depth ratio and length of loose area. Neglecting the inclined slip surface will underestimate the value of the loosening earth pressure, which will lead to the insecurity of the design. Loosening earth pressure calculated by this study was also compared with trapdoor tests. Results from this study was in good agreement with the experimental results. Compared with the traditional 2D solution, results from this study can more accurately analyze the soil arching effect in 3D excavation cases.

This paper deals with investigation of changes in geopolymer wettability with increasing mass fraction of high-carbon fly ash and surface treatment by cold atmospheric plasma (CAP). In this study, multiple samples of geopolymers were prepared, including those with 5% and 10% of high-carbon fly ash from coal-fired power station. Wettability of samples was then measured before and after plasma treatment, both on surface and cut surface. While addition of fly ash only had low effect on the wettability, as in most cases, it only lowered the initial contact angle without speeding up the speed of soaking for compact geopolymer and actually slowed the soaking for foamed geopolymer, plasma treatment had significant impact and made the geopolymer hydrophobic.

In this paper, a plasmonic refractive index sensor based on MIM waveguide (metal_insulation_metal) with two plasmonic waveguides and five rings and two teeth and four rectangular cavities is proposed and designed. The refractive index of the resonators as well as the resonant wavelengths will be investigated by the time difference finite difference method. To achieve an optical sensor with excellent quality and performance, we change the number and type of amplifiers and their dimensions. In each stage of the simulation, we will only change the refractive index of the middle ring located in the middle of the two waveguides, and the refractive index of the other amplifiers remains the same. This challenge will help to form a more appropriate structure for optical sensors. The sensor built in this simulation has a balanced and suitable function for integrated circuits and helps researchers to better understand the design of plasmonic structures. It also has important applications in medical research, health care, drug manufacturing, security monitoring and environmental protection, internal security of countries and the battlefield.

This study examines the effect of surface currents on the bulk algorithm calculation of wind stress estimated using the scatterometer data during 2007-2020 in the Indian Ocean. In the study region as a whole the wind stress decreased by 5.4% by including currents into the wind stress equation. The most significant reduction in the wind stress is found along the most energetic regions with strong currents such as Somali Current, Equatorial Jets and Aghulhas retroflection. A highest reduction of 11.5% is observed along the equator where the Equatorial Jets prevail. A sensitivity analysis has been carried out for the study region and for different seasons to assess the relative impact of winds and currents in the estimation of wind stress by changing the winds while keeping the currents constants and vice versa. The inclusion of currents decreased the wind stress and this decrease is prominent when the currents are stronger. This study showed that equatorial Indian Ocean is the most sensitive region where the current can impact on wind stress estimation. The results showed that uncertainties in the wind stress estimations are quite large at regional levels and hence better representation of wind stress incorporating ocean currents should be considered in the ocean/climatic models for accurate air-sea interaction studies.

The video images captured at long range usually have low contrast floating objects of interest on a sea surface. A comparative experimental study of the statistical characteristics of reflections from floating objects and from the agitated sea surface showed the difference in the correlation and spectral characteristics of these reflections. The functioning of the recently proposed modified matched subspace detector (MMSD) is based on the separation of the observed data spectrum on two subspaces: relatively low and relatively high frequencies. In the literature the MMSD performance has been evaluated in generally and moreover using only a sea model (additive Gaussian background clutter). This paper extends the performance evaluating methodology for low contrast object detection and moreover using only the real sea dataset. This methodology assumes an object of low contrast if the mean and variance of the object and the surrounding background are the same. The paper assumes that the energy spectrum of the object and the sea are different. The paper investigates a scenario in which an artificially created model of a floating object with specified statistical parameters is placed on the surface of a real sea image. The paper compares the efficiency of the classical Matched Subspace Detector (MSD) and MMSD for detecting low-contrast objects on the sea surface. The article analyzes the dependence of the detection probability at a fixed false alarm probability on the difference between the statistical means and variances of a floating object and the surrounding sea.

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Surface activity of humic acid (HA) and its six sub-fractions isolated from forest soil were characterized by surface tension measurements, dynamic light scattering, and laser doppler electrophoresis. The surface tension of HA sub-fractions decreased from 72.4 mN·m-1 to 36.8 mN·m-1 with the increasing concentration from 0 to 20000 mg·L-1. The critical micelle concentration (CMC) of HA and its sub-fractions ranged from 216 to 1024 mg·L-1 with the multiple linear regression equation of CMC = 18896–6.9×C–296×alkyl-C–331×aromatic-C–17019×H/C+4054×HB/HI (p &lt; 0.05). The Z-average particle size ranges from 108.2 nm to 186.9 nm. The maximum particle size was 5000 nm after filtered with a membrane of 0.45 μm, indicating HA and its sub-fractions progressed self-assembly during 2000 mg·L-1, pH = 6.86. The number-base particle size distribution of HA sub-fractions was identified as four peaks by Gaussian model, and the aggregate sizes were mainly in six clusters including 2 ± 1 nm, 5 ± 2 nm, 10 ± 3 nm, 21 ± 8 nm, 40 ± 10 nm, and &gt; 50 nm indicating multiple aggregations of different particle sizes in the HA fractions solution.

The mechanical engineering requires heat treatment after rough machining to reach the mechanical strength, but the heat treatment can induce workpiece deformation, so that the workpiece cannot be reworked. In this study, the plasma was integrated with a lathe, and the on line heat treatment was performed to achieve the mechanical strength and hardness, so as to reduce the machining process and handling. However, for on line heat treatment, it is important to study the machine and plasma parameters of the lathe and plasma, and the research method is used eventually to optimize the process, reduce the machining cost and machining error. The variable factors in surface on line real-time heat treatment are revolution, feed rate and current, the objective function is the hardness of mechanical properties. In the screening experiment, the interaction of factors was discussed using full factorial experiment. The Central Composite Design was combined with the Lack-of-Fit test for optimization experiment, the R2 coefficient was used to determine whether the regression model is appropriate. The optimum parameters were derived from the contour diagram and response surface diagram. The experimental results show that the significant factors include revolution, feed rate and current, the optimum parameters include revolution 168rpm, feed rate 0.068mm/rev and current 86A. The experimental results of optimum parameters show that the surface hardness is increased from 306HLD to 806HLD, the surface hardening effect is enhanced by 163%, so the on line real-time heat treatment equipment has a best hardening effect.

The visual system is regulated by the nervous through neurotransmitters, which play an important role in visual and ocular functions. One of those neurotransmitters is acetylcholine, a key molecule that plays a diversity of biological functions. On the other hand, acetylcholinesterase, the enzyme responsible for the hydrolysis of acetylcholine, is implicated in cholinergic function. However, several studies showed that in addition to their enzymatic functions, Acetylcholinesterase exerts non-catalytic functions. In recent years, the importance of evaluating all possible functions of acetylcholine-acetylcholinesterase has been evidenced. Nevertheless, there is evidence that suggests cholinesterase activity in the eye can regulate some biological events both in structures of the anterior and posterior segment of the eye and therefore in the visual information that is processed in the visual cortex. Hence, the evaluation of cholinesterase activity could be a possible marker of alterations in cholinergic activity not only in ocular disease but also in systemic diseases.

Classical laws of friction suggest that friction force is proportional to the normal load and independent of the nominal contact area. As a great improvement in this subject, it is now widely accepted that friction force is proportional to the real area in contact, and much work has been conducted based on this hypothesis. In present study, this hypothesis will be carefully revisited by measuring the friction force and real contact area in-site and real-time at both normal loading and unloading stages. Our experiments reveal that the linear relation always holds between friction force and normal load. However, for the relation between friction force and real contact area, the linearity holds only at the loading stage while fails at the unloading stage. This study may improve our understanding of the origin of friction.

U.S. Navy Surface Ship depot-level maintenance periods of performance were studied to develop a method for predicting maintenance durations. The need for the method has been highlighted by Navy leadership in recent media posts describing unacceptable maintenance delays and this research provides practitioners and decisionmakers with a reliable estimating tool. This study helps by putting forth a method that defines the rate of work accomplishment based on relevant variables. Using ordinary least squares models, this research revealed that the size of the contract obligation and the amount of shipyard work occurring simultaneously in the market are key variables in determining depot maintenance durations. With the knowledge found here, the next logical step is an optimization model for each U.S. Navy surface ship homeport.

The Covid-19 coronavirus, SARS-CoV-2, is inactivated much faster on paper (3h) than on plastic (7d). By classifying materials according to virus stability on their surface, the following list is obtained (from long to short stability): polypropylene (mask), plastic, glass, stainless steel, pig skin, cardboard, banknote, cotton, wood, paper, tissue, copper. These observations and other studies suggest that SARS-CoV-2 may be inactivated by dryness on water absorbent porous materials but sheltered by long-persisting micro-droplets of water on waterproof surfaces. If such physical phenomenons were confirmed by direct evidence, the persistence of the virus on any surface could be predicted, and new porous objects could be designed to eliminate the virus faster.