About 90% of the Ataulfo mango (Mangifera indica L.) crops in Mexico are in the south of the country. This variety has significant amounts of antioxidant compounds. All the trees come from a small group of parents, however, the possible intravarietal variations and the micro-environments where it is grown can influence the compounds that contribute to the antioxidant capacity. The objective of this study was to quantify the antioxidant compounds of Ataulfo mango fruits of trees grown in Soconusco, Chiapas, Mexico (origin denomination), as well as fruits of the parent trees. In addition, possible associations between the contents of these compounds and the micro-environmental conditions collected were sought. In total, 465 fruits from 155 trees planted in 13 municipalities (locations) were analyzed. Fruits were collected at physiological maturity and stored at 25 °C until reaching commercial maturity. The contents of total phenolic compounds (TPC), antioxidant capacity (AC by DPPH, ABTS and FRAP methods), total anthocyanins (TA) and ascorbic acid (AA) were determined. The fruits from Huehuetán, presented the highest contents of PC (0.89 mg GAE g-1); however, the highest AC was found in the fruits harvested in Frontera Hidalgo, with 128.29 µmol TE g-1 (ABTS). The fruits obtained from the parents are within the average range of total TPC and AC, without significant differences between their fruits and those cultivated. The micro-environments where the Ataulfo mango trees are grown do not have a significant effect on antioxidant compounds (TPC, AC, TA and AA) and the only variables that allow segregation by localities are relative humidity, environmental temperature and altitude.

Severe respiratory syncytial virus (RSV) infections in early life have been linked to the development of chronic airway disease. RSV is a potent inducer of reactive oxygen species (ROS) which contributes to inflammation and enhanced clinical disease. NF-E2-related factor 2 (Nrf2) is an evolutionary conserved redox-responsive protein that helps to protect cells and whole organisms from oxidative stress and injury. The role of Nrf2 in the context of viral-mediated chronic lung injury is not known. Herein, we show that RSV experimental infection of adult Nrf2 deficient BALB/c mice (Nrf2-/-; Nrf2 KO) is characterized by enhanced disease, increased inflammatory cell recruitment to the bronchoalveolar compartment, and a more robust upregulation of innate and inflammatory genes and proteins, compared to wild type Nrf2+/+ competent mice (WT). These events that occur at very early time points, lead to increased peak RSV replication in Nrf2 KO compared to WT mice (day 5). To evaluate longitudinal changes of the lung architecture, mice were scanned weekly by high-resolution micro-computed tomography (micro-CT) imaging up to 28 days after initial viral inoculation. Based on micro-CT qualitative 2D imaging and quantitative reconstructed histogram-based analysis of lung volume and density, we found that RSV infected Nrf2 KO mice developed significantly greater and prolonged fibrosis compared to WT mice. Results of this study underscore the critical role of Nrf2-mediated protection from oxidative injury not only in acute pathogenesis of RSV infection, but also in its long-term consequences of chronic airway injury.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

Two types of trenches cross-section in conventional vertical and brand new reverse-V-shape have fabricated on SCD substrate by micro-jet water-assist laser, the epitaxial lateral overgrowth technique has applied by microwave plasma chemical vapor deposition system in forming multiple micrometer-size channels. Raman and SEM techniques have applied in analyze both types growth layer characterization. Optical microscope has used to test microchannels hollowness. As a result, with the brand new reverse-V-shape trench, epitaxial lateral overgrowth layer reaches higher SCD surface morphology and crystal quality.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

We review recent work on narrowband orthogonally polarized optical RF single sideband generators as well as dual-channel equalization, both based on high-Q integrated ring resonators. The devices operate in the optical telecommunications C-band and enable RF operation over a range of either fixed or thermally tuneable frequencies. They operate via TE/TM mode birefringence in the resonator. We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization for both the fixed and tunable devices.

This paper presents a novel micro-segmented genetic algorithm (μsGA) to identify the best solution for the locomotion of a quadruped robot designed on a rectangular ABS plastic platform. We compare our algorithm with three similar algorithms found in the specialized literature: a standard genetic algorithm (GA), a micro-genetic algorithm (μGA), and a micro artificial immune system (μAIS). The quadruped robot prototype guarantees the same conditions for each test. The platform was developed using 3D printing for the structure and can accommodate the mechanisms, sensors, servomechanisms as actuators. It also has an internal battery and a multicore embedded system (mES) to process and control the robot locomotion. This research proposes a μsGA that segments the individual into specific bytes. μGA techniques are applied to each segment to reduce the processing time; the same benefits as the GA are obtained, while the use of a computer and the high computational resources characteristic of the GA are avoided. This is the reason why some research in robot locomotion is limited to simulation. The results show that the performance of μsGA is better than the three other algorithms (GA, μGA and AIS). The processing time was reduced using a mES architecture that enables parallel processing, meaning that the requirements for resources and memory were reduced. This research solves the problem of continuous locomotion of a quadruped robot, and gives a feasible solution with real performance parameters using a μsGA bio-micro algorithm and a mES architecture.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Various natural disasters such as floods, fires, earthquakes, etc. have affected human life. Detection and classification of large and small earthquakes caused by natural or abnormal events have been always important to Earth scientist. One of the most important research challenges in this field is the lack of an effective method for identifying and categorizing various types of seismic events at less important and important levels. Based on latest achievements of Data Mining international institutions such as Rexer-KDnugget-Gartner and also newest authentic articles, SVM, KNN, C4.5, MLP are from most important and popular and leading classifiers in data world.Therefor in present study, a boost learning system consisting support vector machine algorithms with linear regression, MLP Neural Network ، C4.5 decision tree and KNN near neighborhood have been utilized in a combined form to detect and categorize micro seismic events. In general, the steps involved in the proposed method are: 1) performing artificial seismic tests, 2) data gathering and analysis, 3) conducting preprocessing and separating training and testing samples, 4) generating relevant models with training samples and detecting and categorizing test samples and 5) extracting a cluster with the maximum candidate using boost learning. After simulations, it was observed that the accuracy of proposed boost method to the best answer was about 6.1% higher compare to other methods and the error rate was 0.082% of recalling. Accuracy of detection and classification to the best answer were also improved compare to other methods up to 2.31% and 6.34%, respectively.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

Lots of efforts are made to optimize spectrum quality used for indoor farming to maximize artificial light utilization and reduce water loss. For such an improvement, green (G) light supplementation to a red-blue (RB) background was successfully employed in our previous studies to restrict both non-photochemical thermal dissipation (NPQ) and stomatal conductance (gs). At the same time, however, the downregulation of NPQ and gs influences the leaf temperature (Tleaf) in opposite ways. Thus, to elucidate which factor plays a more prominent role in Tleaf regulation and whether such response is temporal or permanent we investigated the correlation between NPQ or gs and the subsequent Tleaf. To this end, we analysed tomato plants (Solanum lycopersicum L. cv. Malinowy Ozarowski) grown solely under monochromatic LED lamps (435, 520, or 662 nm; 80 µmol m–2 s–1) or under mixed RGB spectrum (1:1:1; 180 µmol m–2 s–1), and simultaneously measured the gs and Tleaf with an infrared gas analyser and thermocouple or employed infrared thermal camera (FLIR) during thermal imaging analyses. Results documented that growth light quality significantly modified the Tleaf, and such response is not temporal. Furthermore, we found that plants' actual adaxial leaf surface temperature is more closely related to NPQ amplitude, while the temperature of the abaxial surface corresponds to gs.

Cross-border e-commerce is an opportunity for micro, small and medium sized enterprise (MSMEs) in developing countries. Based on a resource-based approach, this research studied how to support resource lacking enterprises with export marketing strategy. It dealt with actual business cases of Mongolian entrepreneurs trying to export Mongolian products to Korean market. Multiple source data including interviews, internal documents, and group discussions, were matched with theories to come up with strategies and validated by supporting organizations in Mongolia and Korea. The research suggests that MSMEs should rely on third party digital platforms rather than setting up their own. For product strtategy of the marketing mix, sellecting competitive product categories and supporting them adjusting to foreign markets and quality assurance is needed. For price strategy, loccally high priced products should use a price penetration strategy with a lower price compared to competing foreign products. For place strategy, supporting organizations should partner with exporters for collective delivery. For promotion strategy, they need to support the capacity of MSMEs enabling them to use digital marketing tools effectivly. These strategies were validated and adopted by supporting organizations in Monglia and Korea.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross sections and high optical quality. This is particularly challenging for spatially-constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in SZ2080™polymer with photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modeling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Road traffic transportation has flourished in the process of urbanization by its advantages, but it also produces harmful environmental vibrations. The vibration problem is especially significant for production workshops with precision instruments. A field measurement was conducted to analyze the source characteristics and propagation laws of traffic-induced vibrations. Off the northern side of an urban highway lies a microelectronics workshop. When a large truck passes by, both the vibration responses on the ground and in the workshop considerably increase. Greater vibration is produced in the vertical direction than in the X and Y axes. The predominant frequency band of the vibration response caused by road traffic vehicles is lower than 20 Hz. The vertical vibration responses of the first and second floors in the workshop greatly exceed the VC-C limit because of the high daily traffic flow. Attribute to the excitation of the operation of the manufacturing equipment on the second floor, the vertical vibration level of the second floor is essentially higher than that of the first floor. Therefore, it is impossible to disregard the micro-vibration in the workplace produced by the manufacturing machinery as well as the ex-citement of the road traffic. The measured data can be used to test potential numerical models for forecasting vibrations caused by traffic on roads as well as to guide vibration assessment work throughout the planning and design stages of roads.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

This paper presents a novel dynamic camera parameter control method for position and posture estimation of highly miniaturized AR markers (micro AR markers) using a low cost general camera. The proposed method performs iterative calculation of the marker’s position and posture to converge them to specified accuracy with dynamically updating the camera’s zoom, focus and other parameter values based on the detected marker’s depth distances. For a 10 mm square micro AR marker, the proposed system demonstrated recognition accuracy of better than ±1.0% for depth distance and 2.5∘ for posture angle with a maximum recognition range of 1.0 m. In addition, the iterative calculation time was at most 0.7 seconds in an initial detection of the marker. These experimental results suggest that the proposed method and system can be applied to a robotic precise handling of small objects with low cost.

The genus Eucalyptus is a globally captivated source of hardwood and is well known for its medicinal uses. The hybrid and wild species of Eucalyptus are widely used as exotic plantations due to their renowned potential of adapting to various systems and sites, furthermore, making the species the most extensively propagated. Despite unquestionable progression in biotechnological and tissue culture approaches, the productivity of plantations is still limited often due to the low efficiency of clonal propagation from cuttings. The obtained F1 hybrids yield high biomass and High-quality low-cost raw material for large-scale production, however, the development of hybrid, clonal multiplication, proliferation, and post-developmental studies are still major concerns. This riveting review describes the problems concerned with in-vitro and clonal propagation of Eucalypt plantation; recent advances in biotechnological and tissue culture practices for massive and rapid micro-propagation of Eucalyptus; as well, highlights the Eucalypt germplasm preservation techniques.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

The purpose of this review is to present the current role of ultrasound-based techniques in the diagnostic pathway of prostate cancer (PCa). With overdiagnosis and overtreatment of a clinically insignificant PCa over the past years, multiparametric magnetic resonance imaging (mpMRI) became recommended for every patient suspected of PCa before performing a biopsy. It enabled targeted sampling of the suspicious prostate regions, improving the accuracy of the traditional systematic biopsy. However, mpMRI is associated with high costs, relatively low availability, long and separate procedure or exposure to the contrast agent. The novel ultrasound modalities such as shear wave elastography (SWE), contrast-enhanced ultrasound (CEUS) or high frequency micro-ultrasound (MicroUS) may be capable of maintaining the performance of mpMRI without its limitations. Moreover, the real-time lesion visualization during biopsy would significantly simplify the diagnostic process. Another value of these new techniques is the ability to enhance the performance of mpMRI by creating the image fusion of multiple modalities. Such models might be further analyzed by artificial intelligence to mark the regions of interest for investigators and help to decide about the biopsy indications. The dynamic development and promising results of new ultrasound-based techniques should encourage researchers to thoroughly study their utilization in prostate imaging.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

ST-elevation myocardial infarction (STEMI) remains one of the leading causes of morbidity and mortality worldwide. The identification of novel metabolic and imaging biomarkers could unveil key pathophysiological mechanisms at the molecular level and promote personalized care in patients with acute coronary syndromes. We studied 38 patients with STEMI who underwent primary percutaneous coronary intervention and thrombus aspiration. We sought to correlate serum ceramide levels with micro-CT quantified aspirated thrombus volume and relevant angiographic outcomes, including modified TIMI thrombus grade and pre- or post-procedural TIMI flow. Higher ceramide C16:0 levels were significantly, but weakly correlated with larger aspirated thrombus volume (Spearman r=0.326, p=0.046), larger intracoronary thrombus burden (Nagelkerke R2=0.236, p=0.030) and worse pre- and post-procedural TIMI flow (Nagelkerke R2=0.210; p=0.049 and Nagelkerke R2=0.277; p=0.039, respectively). Ceramides C24:0 and C24:1 were also significantly associated with larger intracoronary thrombus burden (Nagelkerke R2=0.311; p=0.008 and Nagelkerke R2=0.423; p=0.001, respectively). In conclusion, serum ceramide levels (mainly C16:0 and C24:1) were higher among patients with larger intracoronary and aspirated thrombus burden. This suggests that quantification of serum ceramides might improve risk-stratification of patients with STEMI and facilitate a more individualized approach in everyday clinical practice.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

High efficacy LED lamps combined with adaptive lighting control and greenhouse integrated photovoltaics (PV) could enable the concept of year-round cultivation and become a feasible option even in the harsh climate of the Nordic countries. Meteorological satellite data of this region was analyzed in a parametric study to evaluate the potential of these technologies. The generated maps showed monthly average temperatures fluctuating from -20°C to 20°C throughout the year. The natural photoperiod and light intensity also changed drastically, resulting in monthly average daily light integral (DLI) levels ranging from 45-50 mol·m-2·d-1 in summer and contrasting with 0-5 mol·m-2·d-1 during winter. To compensate, growth room cultivation independent from outdoor conditions could be used in winter. Depending on the efficacy of the lamps, the electricity required for sole-source lighting at 300 µmol·m-2·s-1 for 16 hours would be between 1.4 and 2.4 kWh·m-2·d-1. Greenhouses with supplementary lighting could help start the cultivation earlier in spring and extend it further into autumn. The energy required for lighting highly depends on several factors such as the natural light transmittance, the light threshold settings and the lighting control protocol, resulting in electric demands between 0.6 and 2.4 kWh·m-2·d-1. Integrating PV on the roof or wall structures of the greenhouse could offset some of this electricity, with specific energy yields ranging from 400 to 1120 kWh·kWp-2·yr-1 depending on the region and system design.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

The severe and complex COVID-19 symptoms, often needing hospital care, occur suddenly, late in the virus replication stage of SARS-CoV-2 infection. Hospitalised patients have tissue damage due to micro-clots at multiple sites. Could long-covid, also clinically variable, be a milder form caused by “nano-clots”, too small to cause detectable tissue damage? The timing and suddenness of the onset of serious disease needs an explanation. A paper reported on the first 20 children needing urgent hospital care. No child had any symptoms prior to suddenly becoming seriously ill, only one had a positive PCR test but all had positive SARS-CoV-2 antibody test. That finding indicated to me that this onset occurred at the moment of sero-conversion. An emerging viral moiety, the virion-IgG-antibody complex, has concentrations rapidly increasing, then decreasing. It is known that influenza-IgG-antibody-complex consists of many virions bound together by the antibody. It seems a reasonable step to propose that SARS-2, being a large virus and having many spike proteins, can form larger clumps of virus-IgG-antibody complexes than with influenza, the former being sufficiently large to initiate micro-clots. Therefore, my hypotheses is that the SARS-CoV-2 virion-antibody complex initiates micro-clot formation. Either before or after sero-conversion, the complex will be at too low a concentration to initiate micro-clots. To be useful, a hypothesis should be testable, provide explanations and give predictions. My presentation will give examples. I like the way that several apparently separate pieces of a jig-saw puzzle have come together to form a single picture. [I suggest that the reader scrolls down to the addenda [10,11 & 12] before reading the ICAR Poster]

The spatial segregation is a characteristic of Latin American cities, resulting in distinct dynamics of social inclusion and exclusion at both spatial and identity levels. Then, specific green spaces may convert into appreciated and contested territories, where various actors negotiate their uses and regulations. Considering a case-study in a green icon of the metropolitan city of Santiago de Chile, the main objective of the present study was to describe and comprehend the uses and meanings of the Quebrada Macul park among different social groups over the past two decades. We employed qualitative methods including six in-depth interviews with key informants (social and ecological leaders, historical neighbors, and park workers), five participant observations in the park, and statistical analysis of visitors. Results reveal that (1) the transition of being a popularly used hill to a metropolitan park rises tensions between public and private statuses of place; (2) conflicts emerge regarding who uses the space and how, reflecting power dynamics among different social groups; (3) the park, beyond being a public space, holds significant identity value for its historical residents, both for those who fought for its recovery and those who have lived closely, so processes of forgetfulness might be resentful. We conclude on enduring meanings of the park associated with the struggle for the place among different groups, highlighting the role of memory for the social integration of groups among natural spaces.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

Micro-plastics (MPs) become significantly important to society since their commercial manufacture began in the 1950s because of their low production costs, stability, light weight, and adaptability. Plastic was produced in 400 million tons worldwide in 2020, compared to 1.5 million tons just 60 years earlier. Scientists predict that by 2050, plastic production would increase to 33 billion tons. MPs are a rising scientific and societal issue in the environment as a new type of contaminant that is widely disseminated in aquatic ecosystems and organisms. Aquatic species that come into contact with MPs for an extended period of time experience ecotoxicity, which includes oxidative stress, genotoxicity, neurotoxicity, and reproductive issues. In aquatic environments, MPs not only transport chemicals within animals but also serve as mediators for chemicals or other contaminants. As a result of co-exposure of MPs and chemical contaminants, various toxicity incidences involving aquatic organisms have been reported. The final exposure of MPs occurs in humans through biomagnification of aquatic edible products. This study presents an important overview of the literature on MP ingestion by aquatic biota. It covers topics such as the present scenario of plastic pollution worldwide, the pathways that MPs take to reach humans and aquatic species, the eco-toxicological impacts of MPs on aquatic species, the relation between MPs and other environmental pollution and the ensuing effects on aquatic organisms, and the MP pollution status in Bangladesh.

Castanea sativa Mill., an indigenous species of the mountainous Gabala region of Azerbaijan, where its local variety is now facing the danger of extinction. The preservation of this variety of European chestnut requires the development of effective strategies for reliable in vitro regeneration systems as an alternative to traditional methods, which has become the main objective of this study. In solving this problem, the generally accepted technique of micro-multiplication of axillary shoots was mainly used. First, a phased sterilization of was carried out using liquid soap, Previkur fungicide and mercury (II) chloride. DKW (Driver and Kuniyuki Walnut) nutrient medium was used for germination of explants, into which growth stimulants BAP (Benzilamunapurine), IBA (Indole - 3 butyric acid), IAA (Indole Acetic acid), NAA (Naphthalene Acetic Acid) and GA3 (Gibberelic acid) were introduced in various combinations and quantities. The test of the above-mentioned sterilization model revealed significant shortcomings in terms of the acceptability of the results obtained (16-77%). It was also found that the germination of explants takes 14 days and it is better to conduct it in a DKW environment containing hormones BAP (0.6 mg), IBA (0.1 mg) and GA3 (0.1 mg) / 1 L DKW. A mixture of BAP (0.1mg) + IBA (0.35 mg) is more suitable for the reproduction of grown explants + GA3 (0.2 mg) / 1 l DKW (the result is 3 new micro-plants for each explant), and for good root formation (it takes 30 days) – a mixture of IBA 1.0 mg + NAA 0.5 mg + IAA 0.5 mg / l L DKW. After the shoots have acquired a certain length (at least 1.5 cm), it is required to transfer them for 22 days to a DKW medium containing IBA (1 mg), IAA (0.5 mg) and NAA(0.5 mg) / l L DKW so that the root splitting process begins and ends.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Artificial intelligence, a key technological tool in the era of the 4th Industrial Revolution, is being actively applied to education beyond industry, economy, and culture. In the future society, understanding and using artificial intelligence technology will be considered an essential skill for everyone, and the professionalism of AI education for pre-service teachers nurturing future talents is also important. This study verifies the effectiveness of pre-service teachers after undergoing a 15-week extension program consisting of AI Literacy Education (10 weeks), AI-Linked Subjet Education (3 weeks), and Micro-teaching (2 weeks) which was designed to enhance the AI ​​education professionalism of pre-service teachers. The AI Literacy Education section consisted of understanding AI, AI ethics, and basic programming, and the education was conducted through both experience and practice. After that, the pre-service teachers analyzed the curriculum of the 5th and 6th grades of an elementary school, and developed a subject-related education program using AI tools in three stages. Using the developed program, micro-teaching classes were conducted twice. The study results are as follows. First, there was a change in the positive perception of AI (p<.05). Second, the understanding of AI educational technology tools was improved and the recognition of the usefulness of developing a curriculum-related program was expanded. Third, the importance of teacher competency development was learned through the micro-teaching, and the students' understanding of the learning process was expanded.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

Calibration of flow devices is important in several areas of pharmaceutical, flow chemistry and microfluidic applications where dosage of process liquids or accurate measurement of the flow rate is important. The process-oriented liquid itself might influence the performance of the flow device and the simultaneous determination of the dynamic viscosity under flow conditions might be a valuable information for the process parameters. To offer the simultaneous calibration of the dynamic viscosity of the process-oriented liquid at the corresponding flowrate, METAS has built a pipe viscometer for the traceable in-line measurement of the dynamic viscosity in the current flow facilities for low flow rates from 1 L/min to 150 mL/min and pressure drops up to 10 bar. The traceability of all the measuring quantities as well as the geometrical dimensions of the micro tube guarantee the traceability of the pipe viscometer to SI units. The most challenging part is the traceable determination of the inner diameter of the micro tube. This can be achieved by measuring the pressure drop as a function of flow rate with the pipe viscometer and applying the law of Hagen-Poiseuille with a traceable dynamic viscosity of a reference liquid (water) or perform the measurements with the micro-CT at METAS, which determines the inner diameter by x-ray diffraction. The validation of the stated measurement uncertainty of the pipe viscometer has been performed by means of calibration of the dynamic viscosity of several reference liquids with traceable density and kinematic viscosity. The setup of the facility, the traceability as well as the uncertainty calculation of the pipe viscometer for the in-line measurement of the dynamic viscosity are discussed in this paper.

Micro-expression (ME) is one of the key psychological stress reactions. It is a modest, spontaneous facial mechanism. ME has significant applicability in a variety of psychologically-related sectors because to its precision and unpredictability with regard to psychological manifestations. Nevertheless, the current Micro-expression recognition (MER) algorithms have poor accuracy and a limited quantity of ME data, and this study issue has not been thoroughly investigated. Therefore, we present an approach for deep learning based on a Spatio-temporal capsule network (STCP-Net). STCP-Net has four components: a jitter reduction module, a differential feature extraction module, an STCP module, and a fully linked layer. The first two modules are aimed to extract diversifying differential features more precisely and to limit the influence of head jitter. The STCP module is used to extract Spatio-temporal features layer by layer, taking the temporal and geographical connection between features into account. This research runs sufficient trials using the Leave One Subject Out (LOSO) methodology for cross-validation using the CASMEII dataset. The conclusion and analysis demonstrate that the algorithm is innovative and efficient.

Cancer stem cells (CSCs) are one of the cell types that account for cancer heterogeneity. They arrest in the G0 phase and generate non-CSC progeny by self-renewing and pluripotency activity, resulting in tumor recurrence, metastasis, and chemoresistance. One CSC can stimulate tumor relapse and can re-grow a metastatic tumor. So, CSC is a promising target for eradicating tumors, and developing an anti-CSC method has become a top priority in cancer therapy. In recent years competing endogenous RNA (ceRNA) have emerged as an important class of post-transcriptional regulators that affect gene expression via competition for microRNA (miRNA) binding. Furthermore, aberrant ceRNA expression is associated with tumor progression. To overcome therapeutic resistance due to CSCs, we need to improve our existing understanding of the mechanisms by which ceRNAs are implicated in CSC-related relapse. Thus, this review was designed in order to discuss the role of ceRNAs in CSCs function. We reviewed the role of ceRNAs in acquiring CSCs characteristics in the form of different pathways including Rho GTPase/F-actin_ Yes-associated protein (YAP)/transcriptional co-activator with PDZ-binding motif (TAZ) (Hippo), Wnt/β-catenin pathway, transforming growth factor (TGF)-b–urothelial carcinoma-associated 1 (UCA1)–Slug pathway, etc. Finally, considering the comprehensive impacts of the ceRNA network on different pathways, a treatment strategy driving the ceRNA network might be effective. Targeting ceRNAs may open the path for new cancer therapeutic targets and can be used in clinical research.

This research was specifically aimed at assessing the influence of sulfur in triple-super phosphate (TSP) on wheat yield. From the results, wheat showed response to sulfur (S) from gypsum (in 67%); and nitrogen (N) from urea in about 100% (of 24 sites). Based on this N was found to be the most limiting element to wheat production followed by sulfur, and then by phosphorus. TSP is tested to contain agronomically up to 2-6% by weight of S. However, wheat didn’t show response to S impurity supplied in the form of TSP. Though, not statistically significant, it is observed that there have always been yield increments by certain percent due to S from TSP in 8 out of 10 target sites, which is depicted in the increasing trends of yield response curves. From this it is learnt that, the benefits of the accidental/incidental application of such high analysis fertilizers can be many-folds in the quality attributes of wheat, if the soils of such investigation at the same time would contain significant amount of organic matter (OM). Indeed, such analysis would be vital in varietal specific nutrient requirement studies in precision-farming and/or in categorizing soils into fertility gradients and fertilizer recommendation domains.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

We review recent work on broadband RF channelizers based on integrated optical frequency Kerr micro-combs combined with passive micro-ring resonator filters, with microcombs having channel spacings of 200GHz and 49GHz. This approach to realizing RF channelizers offers reduced complexity, size, and potential cost for a wide range of applications to microwave signal detection.

The optimization problem of two or more special-purpose functions of the energy system is subjected to an analysis. Based on experience of our research and general knowledge of partial solutions of energy system optimization at the level of control of production and power energy supply by energy companies in the Czech Republic, a special-purpose (cost) function has been defined. By analysing the special-purpose function, penalty and limitations have been defined. Using the fuzzy logic, a set of suitable solutions for the special-purpose function is accepted. An optimum of the special-purpose function is looked for using the simulated annealing method. The history of electricity consumption is sorted by day and by hour, representing the multidimensional data. When using the cluster analysis, type daytime diagrams of consumption are defined. Type daytime diagrams form prototypes of identified clusters. The so-called self-organizing neural network with Kohonen map attached is used to perform the cluster analysis. The result of our research is presented by an experiment.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Balínt Syndrome is an acquired disorder manifesting in the inability to recognize several objects at once (simultagnosia), inaccurate visually guided limb movements despite intact motor function (optic ataxia) and the inability to make accurate voluntary saccades to visual targets despite demonstrating unrestricted range of eye movements (ocular motor apraxia). Here we report the first case of a patient presenting with Balínt Syndrome caused by a platelet-derived growth factor receptor A mutation (PDGFRA)-induced Hypereosinophilic Syndrome (HES).

This paper proposes a novel micro-grid structure, which can operate fully-autonomously with inherent seamless switching. It can operate independently in both grid-connected and islanded mode as a self-governed entity without relying on the utility grid. An AC/DC/AC converter is employed as the interface between the micro-grid and the utility grid, which enables the two entities to have different voltages in grid-connected mode. Seamless switching between operation modes can be achieved naturally. The micro-grid is regulated to exchange predefined amount of power with the utility grid in grid-connected mode. This will benefit the power dispatching algorithm of the power system. The predefined power is estimated based on power forecasting of local renewable generations and loads with consideration of the Sate of Charge (SOC) of the battery, and is updated and broadcasted every certain period. A small scale AC micro-grid with a rotating generator, battery storage and solar arrays etc. is built for investigation. Matlab/Simulink results are provided to validate the robustness and flexibility of proposed micro-grid and its operation strategy.

A novel hybrid cobalt phosphite, (H2DAB)[Co(H2PO3)4]·2H2O, has been synthesized by using slow evaporation method, in the presence of cobalt nitrate, phosphorous acid and 1,4- dia-minobutane (DAB= 1,4- diaminobutane) as a structure-directing agent. Single crystal X-ray diffraction analysis showed that the compound crystallizes in the P-1(n.2) triclinic space group, with the following unit cell parameters (Å, °) a = 5.4814 (3), b = 7.5515 (4), c = 10.8548 (6), α = 88.001 (4), β = 88.707 (5), γ = 85.126 (5), and V= 447.33 (4) Å3. The crystal structure was built up from cor-ner-sharing [CoO6] octahedra, forming chains parallel to [001], which are interconnected by H2PO3 pseudo-tetrahedral units. The deprotonated cations, residing between the parallel chains, interacted with the inorganic moiety via hydrogen bonds leading thus to the formation of the 3D crystal structure. The Fourier transform infrared spectrum showed characteristic bands corresponding to the phosphite group and the organic amine. The thermal behavior of the compound consisted mainly of the loss of its organic moiety and the water molecules. The biological tests exhibited significant activity against Candida albicans and Escherichia coli strains in all used concentrations, while less inhibitory activity was pronounced against Staphylococcus epidermidis and Saccharomyces cerevisiae, and in the case of multi-cellular organisms, no activity against the nematode model Steinernema feltiae was detected.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

In recent years, Web APIs have become a de facto standard for exchanging machine-readable data on the Web. Despite this success though, they often fail in making resource descriptions interoperable due to the fact that they rely on proprietary vocabularies that lack formal semantics. The Linked Data principles similarly seek the massive publication of data on the Web, yet with the specific goal of ensuring semantic interoperability. Given their complementary goals, it is commonly admitted that cross-fertilization could stem from the automatic combination of Linked Data and Web APIs. Towards this goal, in this paper we leverage the micro-service architectural principles to define a SPARQL Micro-Service architecture, aimed at querying Web APIs using SPARQL. A SPARQL micro-service is a lightweight SPARQL endpoint that provides access to a small, resource-centric, virtual graph. In this context, we argue that full SPARQL Query expressiveness can be supported efficiently without jeopardizing servers availability. Furthermore, we demonstrate how this architecture can be used to dynamically assign dereferenceable URIs to Web API resources that do not have URIs beforehand, thus literally ``bringing'' Web APIs into the Web of Data. We believe that the emergence of an ecosystem of SPARQL micro-services published by independent providers would enable Linked Data-based applications to easily glean pieces of data from a wealth of distributed, scalable and reliable services. We describe a working prototype implementation and we finally illustrate the use of SPARQL micro-services in the context of two real-life use cases related to the biodiversity domain, developed in collaboration with the French National Museum of Natural History.

This study investigated the roles of transactions cost in MSMEs access to finance. This was done by investigating the impact of transactions cost on access to credit from both MSMEs and financial institutions (commercial banks and microfinance banks). From the MSMEs’ side, borrowing experience, decision lag, firm size and borrowers’ distance to the loan office were investigated. On the financial institution’s side, the costs of information gathering, loan administration, monitoring and loan enforcement were investigated. We used the questionnaire survey method, in-depth interviews and case studies, as well as the annual financial statements of the banks. We identified interest rate and collateral value as constraints to access to finance for MSMEs. We also found financial institutions’ attitude to MSMEs access to credit was not friendly. Financial institutions need to do more to bring down transaction cost of lending. This hopefully can be achieved by investing more in agent banking which would lower operating costs, as well as spreading risk, and ultimately increase credit intermediation to small businesses.

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

Triangles are an ever present feature in nature, which the building construction industry duly echoes. However, an exact expression intended to offer the radiant field due to any triangle in an upright or inclined position had not been identified by previous research. In this case, the author has been able to solve by direct integration, the canonical expression of radiative transfer. This result alone confers a myriad of possibilities that had been inconceivable before, for studying in detail the three-dimensional heat transfer behavior of volumes and figures in which triangles do manifest, such as fins, windows, roof-gables and louvers of various kinds. Typically, shading devices, when tilted, give rise in their extremes to rhomboidal shapes which were difficult to take into account or had to be subject to discretization and subsequent Monte Carlo methods in order to perform an approximate calculation of their emission. This implied a lengthy and inexact procedure that induced many errors and consumed computing time. We can now avoid all the former downsides due to the advances hereby presented. As the novel expression can be converted into an algorithm it will be advantageously employed for simulation. This significant finding dovetails in the intricate puzzle of radiated heat and we believe that their consequences will greatly affect the conception and design of HVAC devices, aircraft manufacturing and specifically building or lighting industries among others.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

This research investigates the microstructure and mechanical behaviour of a polylactic acid (PLA)-iron (PLI) composite designed to enable magnetic actuation. Tensile specimens of PLI are produced through Fused Filament Fabrication, incorporating diverse printing angles ranging from 0° to 90°, thereby facilitating the creation of a variety of layups. The microstructure of these 3D-printed composites is analysed using X-ray micro-tomography. Furthermore, the tensile mechanical properties of all composites are evaluated, and the findings are deliberated in relation to the conditions of the printing angle. Additionally, the fractography of broken specimens is examined using Scanning Electron Microscopy. The findings indicate that the printing angle plays a significant role in influencing the tensile properties of the 3D-printed PLI composites, particularly in adjusting mechanical anisotropy. Moreover, an optimal layup of 45°/45° is attained, resulting in an enhanced ranking of the tensile performance. These findings related to 3D-printed PLI composites present a cost-efficient option for manufacturing bio-sourced light-adaptive composites through 3D printing, enabling the generation of intricate magnetic actuation performance.

A fern, Polypodium aureum, possesses a specialized spore-releasing mechanism like a catapult induced by quick expansion of vaporized bubbles. This study introduces lipid-coated perfluorocarbon droplets to enable repeatable vaporization-condensation cycles, inspired by the repeatable vaporization of Polypodium aureum. Lipid-perfluorocarbon droplets have been considered not to exhibit repeatable oscillations due to bubble collapse by low surface tension of lipid layers. However, a single lipid-dodecafluoropentane droplet with a diameter of 9.17 µm shows expansion-contraction oscillations over 4,000 cycles by changing lipid composition and applying low power of 1.7 MHz ultrasound to induce partial vaporization of droplets. The optimal combinations of shell composition, droplet fabrication, and acoustic conditions can minimize damage on shell structure and quick recovery of damaged shell layers. The highly-expanding oscillatory microbubbles provide a new direction for fuel-free micro or nanobots as well as biomedical applications of contrast agents and drug delivery.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

Traumatic brain injury (TBI) affects millions of people annually, however, our knowledge of the diffuse pathologies associated with TBI is limited. As diffuse pathologies, including axonal injury and neuroinflammatory changes, are difficult to visualize in the clinical population, animal models are used. In the current study we used the central fluid percussion injury (CFPI) model in a micro pig to study the potential scalability of these diffuse pathologies in a gyrencephalic brain of a species with inflammatory systems very similar to humans. We found that both axonal injury and microglia activation within the thalamus and corpus callosum are positively correlated to the weight-normalized pressure pulse, while subtle changes in blood gas and mean arterial blood pressure are not. We also found that the majority of tissue generated up to 10 years previously is viable for immunofluorescent labeling after long-term refrigeration storage. This study indicates that a micro pig CFPI model could allow for specific investigations of various degree of diffuse pathological burdens following TBI.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

This review paper delves into using micro-credentials in higher education ecosystems as a digital enablers. Micro-credentials, which are digital credentials that attest to a learner’s mastery of a specific skill or knowledge area, are becoming more popular in higher education. The paper examines the successful implementation of micro-credential frameworks in higher education, using case studies to demonstrate the advantages of micro-credentials. The review emphasizes the agility and flexibility of microcredentials, which enable learners to acquire new skills quickly and respond to changes in the job market. In addition, the paper discusses the digital nature of micro-credentials and how they allow institutionsto provide targeted, skills-based training that isrelevant to employers. It also explores how micro-credentials are delivered through online platforms, making them convenient and easily accessible for learners. The review underscores the significance of digital infrastructure, connectivity, and public utility for promoting micro-credentials. The paper argues that micro-credentials function as a digital enabler for higher edu- cation ecosystems, allowing learners to acquire targeted training and enabling institutions to expand their offerings and reach more students. The paper concludes by highlighting the potential for micro-credentials to help bridge the skills gap and equip learners with the skills necessary to succeed in today’s digital economy.

Micro-level language policy and planning (LPP) primarily concerns local actors' decision-making on matters in relation to language(s) and its users. Despite a growing body of literature focusing on micro language planning in educational settings, there is a scarcity of research examining early childhood education settings such as micro-level LPP context for young English language learners. By adopting a case study approach, the present study examined the educators' enactment of agency in micro-planning the English language education policy (LEP) in one Chinese kindergarten and the associated factors shaping their agency. Our study revealed that the sustainable implementation of the kindergarten English LEP depended on the principal, native English-speaking teachers, and the Chinese assistant teachers' different degrees of agency. Also, the research findings indicated an array of contextual and individual factors nested in a hierarchical structure that facilitated, guided, and constrained the educators' agency in a role-and circumstance-dependent manner. This study contributes to the pertinent literature by casting nuanced light on the different educators' contributions to the micro-level LPP against a national policy that does not endorse early-year English language education.

The study purpose was to train and validate a deep-learning approach to detect micro-scale streetscape features related to pedestrian physical activity. This work innovates by combining computer vision techniques with Google Street View (GSV) images to overcome impediments to conducting audits (e.g., time, safety, and expert labor cost). The EfficientNETB5 architecture was used to build deep-learning models for eight micro-scale features guided by the Microscale Audit of Pedestrian Streetscapes-Mini tool: sidewalks, sidewalk buffers, curb cuts, zebra and line crosswalks, walk signals, bike symbols, and streetlights. We used a train--correct loop, whereby images were trained on a training dataset, evaluated using a separate validation dataset, and trained further until acceptable performance metrics were achieved. Further, we used trained models to audit participant (N=512) neighborhoods in the WalkIT Arizona trial. Correlations were explored between micro-scale features and GIS-measured- and participant reported-macro-scale walkability. Classifier precision, recall, and overall accuracy were all >84%. Total micro-scale was associated with overall macro-scale walkability (r=0.300,p<.001). Positive associations were found between model-detected and self-reported sidewalks (r=0.41,p<.001) and sidewalk buffers (r=0.26,p<.001). Computer vision model results suggest an alternative to trained human raters, allowing for audits of hundreds or thousands of neighborhoods for population surveillance or hypothesis testing.

A theoretical description of quantum jumps at the level of elementary particles is proposed, based on a micro-cosmological interpretation of their de Broglie phase. The third quantization formalism proposed in current literature for the description of baby universes in quantum cosmology is used here to describe the breakdown of unitarity in the transition from the pre-jump to the post-jump wave function. The corpuscular aspect manifested by the particle in the micro-interaction that originates the jump is represented by a pair of evanescent "micro-universes", respectively pre- and post-jump, connected by a wormhole. The latter represents the actual implementation of the interaction that leads to the projection on the outgoing state; this interaction is always local, even when the selected outgoing state is entangled. Therefore, the decoherence which leads to the emergence of classicality is originated by the same fundamental interactions of the Standard Model involved in the unitary evolution of the wave function. The objective nature of the reduction process admits implications on the possibility of using the formalism in the cosmological context, which are briefly discussed.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

During March and April 2020, the European Union (EU) was the center of the COVID-19 pandemic. Many National Governments imposed severe lockdown policies to mitigate the health crisis. The European Parliament commissioned a survey to analyse the citizens’ attitudes over a number of issues related to the COVID-19 pandemic. 21804 European citizens in 21 EU countries responded the survey between 23 April and 1 May 2020. The paper analyses empirically the individual satisfaction that European citizens have experienced over the measures taken by the respective National Governments to control the COVID-19 pandemic. The analysis is based on a micro-econometric model (ordered probit) that explains the citizens’ satisfaction by a number of attitudes and sociodemographic factors. Our results reveal that Spaniards are the least satisfied citizens in comparison with Danes, Irelanders, Greeks and Croats who are the most satisfied nationals. The years of education and the social class also play a determinant role. We also find that the most important determinant is the political support to the Government, and that those who are more worried by the economy and the protection of individual rights are usually more critic with the measures than those who are more worried by the health consequences.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

Mineral profile of beef interests human health, but also animal performance and meat quality. This study analyzes the relationships of 20 minerals in beef (ICP-OES) with 3 animal performance and 13 meat quality traits analyzed on 182 samples of Longissimus thoracis. Animals’ breed and sex showed limited effects. The major sources of variation (farm/date of slaughter, individual animal within group and side/sample within animal) differed greatly from trait to trait. Mineral contents were correlated to animal performance and meat quality being significant 52 out of the 320 correlations at the farm/date level, and 101 out of the 320 at the individual animal level. Five latent factors explained 69% of mineral co-variation. The most important, “Mineral quantity” factor correlated with age at slaughter and with the meat color traits. Two latent factors (“Na+Fe+Cu” and “Fe+Mn”) correlated with performance and meat color traits. Two other (“K-B-Pb” and “Zn”) correlated with meat chemical composition and the latter also with carcass weight and daily gain, and meat color traits. Meat cooking losses correlated with “K-B-Pb”. Latent factor analysis appears be a useful means of disentangling the very complex relationships that the minerals in meat have with animal performance and meat quality traits.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

Purpose: The objective of the study was to qualitatively assess micro-gap dimensions, connecting fitting surface profile and bacterial leakage of machined and cast high gold alloy UCLA abutments, with or without electrodeposited gold coatings attached to external hexagon implants. Materials and methods: 16 plastic UCLA (PUCLA) and 5 machined cast-to UCLA (GUCLA) abutments were cast with a high gold content alloy. 10 were electrolytically gold plated (8 - PUCLA, 2 - GUCLA). All abutments were attached to implants giving 21 implant-abutment combinations (IACs). External perimeter micro-gaps measured with SEM under different illumination and magnification conditions were averaged over three regions. The IACs were examined for E.coli leakage following an initial sterility test. Disassembled combinations were examined with SEM and surface profiles qualitatively assessed. Results: External micro-gap measurements did not reflect the variable connecting surface profiles but average values < 3.5 μm were observed for all IACs. Bacterial transfer was observed in 3 of 5 PUCLA plated and 2 of 5 PUCLA non-plated IACs. No transfer occurred in the 3 GUCLA non-plated or 2 GUCLA plated IACs. Abutment connecting surfaces, both Au plated and not Au plated, showed plastic deformation (smearing) in variable mosaic patterns across the micro-gap. External micro-gap dimensions although not truly reflective of surface connecting profiles averaged < 3.5 μm measured under shadow eliminating silhouette illumination for both cast and pre-machined external hexagon abutments with and without Au plating. Conclusions: Micro-gap dimensions < 5 μm were obtained with both high noble metal cast and pre-machined external hexagon abutments with and without Au electrodeposited on the abutment connecting surface. Regions of intimate contact due to plastic deformation (smearing) of these surfaces was observed. A continuous smeared region around the circumference of the surfaces can provide an effective barrier to egress of E.coli bacteria from the internal regions of the implant under static loading.

Micro-arc oxidation (MAO) is an emerging technology employed to produce high hardness or anti-corrosion ceramic coatings on lightweight metals such Al, Ti, Mg and their respective alloys. However, under non-lubrication conditions, such coatings exhibit relatively high friction coeffi-cients. To enhance the friction reduction properties of the MAO coatings, we employed a one-step MAO process with varying concentrations of graphene oxide (GO) in an aluminate sys-tem electrolyte to create composite coatings on the surfaces of Ti-6Al-4V alloy. The effect of concentrations of GO particles on microstructure, composition, and wear behavior of the result-ing composite coatings was investigated. Measurements of the coating's thickness, hardness, and roughness have also been conducted. Ball-on-disk friction test under dry condition were carried out to reveal tribological behavior of the MAO coating. The addition of graphene oxide in the electrolyte reduces the friction coefficient, with the composite coating containing 5 g/L of GO particles displaying the most effective friction reduction. Moreover, coating thickness increases with higher GO concentration. This friction reduction can be attributed to the particles in the coating acting as lubricants during friction, while GO also reduces adhesive damage, shifting the wear mechanism from adhesive to abrasive.

For the first time, an environmentally friendly waste-free closed cycle for the formation of EMI shielding materials that are promising for 5G communications is considered. Based on the proposed closed technological cycle, two types of EMI shielding materials have been obtained; both materials have significant prospects for signal shielding in all ranges that are allocated in different countries for 5G communication. The first type of materials are transparent conductive meshes with a transparency of more than 80% and with a shielding efficiency of more than 40 dB in the S and L bands and about 30 dB in the K and Ka bands. The study of signal reflection characteristics in the S, L, C, K and Ka bands showed the promise of using these materials as transparent 5G signal reflectors. The reflection coefficient in all considered ranges is above 90% (-0.5 dB). The second type of shielding material are continuous silver micro caps films characterized by a shielding efficiency of 90.1 dB at a thickness of 6.2±1.2 µm. We have also shown that silver micro caps can separate into silver flakes and ribbons when sonicated. These materials can also be used to produce EMI shielding coatings and composites. A detailed analysis of the shielding properties showed that each type of materials obtained in a closed technological cycle is comparable with the best literature results and significantly wins in terms of cost.