Magnesium nanoparticles of various mean diameters (53 – 239 nm) were synthesized herein via Pulsed Laser Ablation in Liquid (PLAL) from millimeter sized magnesium powders within iso-propyl alcohol. It was observed via a 3x3 full factorial DOE that the processing parameters can control the nanoparticle distribution to produce three size-distribution types (bimodal, skewed and normal). Ablation times of 2, 5, and 25 minutes where investigated. An ablation time of 2 minutes produced a bimodal distribution with the other types seen at higher periods of processing. Mg nanoparticle UV-Vis absorbance at 204 nm increased linearly with increasing ablation time, indicating an increase in nanoparticle count. The colloidal density (mg/ml) generally increased with increasing nanoparticle mean diameter as noted via increasing UV-vis absorbance. High la-ser scan speeds (within the studied range of 3000 - 3500 mm/s) tend to increase the nanoparticle count/yield. For the first time, the effect of scan speed on colloidal density, UV-vis absorbance and nanoparticle diameter from metallic powder ablation was investigated and is reported herein. The nanoparticles formed dendritic structures after being drop cast on aluminum foil as observed via FESEM analysis. Dynamic light scattering was used to measure the size of the nanoparticles. Magnesium nanoparticles have promising use in the fabrication of wearables, such as in conductive tracks or battery electrodes, owing to their low heat capacity, high melting point and bio-compatibility.

In recent years, solid state terahertz (THz) modulators have obtained rapid progress with the widespread use of two-dimensional (2D) materials in the field of THz; however, challenges remain in preparing flexible THz modulators. In this study, flexible ferromagnetic nematic materials were prepared by doping thermotropic nematic liquid crystals 5CB into magnetic fluids, and the influence of hydrogen bonding in water was reduced by a self-made cyclic olefin copolymer (COC) microfluidic chip. THz modulation characteristics of magnetic fluid and ferromagnetic nematic liquid crystal (FNLC) under the induction of external magnetic field were compared using a THz time domain spectroscopy system. Under the action of a 91 mT magnetic field, the magnetic fluid has a maximum modulation depth (MD) of 54%. Under the same magnetic field, the maximum MD of the ferromagnetic nematic liquid crystal materials increase to 78% because of the rearrangement of Fe3O4 nanoparticles induced by the topological defect of the liquid crystal. We demonstrate that the magneto-optical effect is significantly enhanced in the ferromagnetic nematic liquid crystal hybrid system. This strategy of doping thermotropic nematic liquid crystals to enhance the magneto-optical effect has great potential for THz filtering, modulation, and sensing applications.

Falling snow alters its own microwave signatures when it begins to accumulate on the ground, making retrieval of snowfall challenging. This paper investigates the effects of snow-cover depth and cloud liquid water content on microwave signatures of terrestrial snowfall using reanalysis data and multi-annual observations by the Global Precipitation Measurement (GPM) core satellite with particular emphasis on the 89 and 166 GHz channels. It is found that over shallow snow cover (snow water equivalent (SWE) ≤ 100 kg m^-2) and low values of cloud liquid water path (LWP 100–150 g m^-2), the scattering of light snowfall (intensities ≤ 0.5 mm h⁻¹) is detectable only at frequency 166 GHz, while for higher snowfall rates, the signal can also be detected at 89 GHz. However, when SWE exceeds 200 kg m^-2 and the LWP is greater than 100–150 g m^-2, the emission from the increased liquid water content in snowing clouds becomes the only surrogate microwave signal of snowfall that is stronger at frequency 89 than 166 GHz. The results also reveal that over high latitudes above 60°N where the SWE is greater than 200 kg m^-2 and LWP is lower than 100–150 g m^-2, the snowfall microwave signal could not be detected with GPM without considering a priori data about SWE and LWP. Our findings provide quantitative insights for improving retrieval of snowfall in particular over snow-covered terrain.

Over the last decades, microalgal biomass has gained a significant role in the development of different high-end (nutraceuticals, colorants, food supplements, and pharmaceuticals) and low-end products (biodiesel, bioethanol, and biogas) due to rapid growth and high carbon fixing efficiency. Therefore, microalgae are considered a useful and sustainable resource to attain energy security while reducing our current reliance on fossil fuels. From the technologies available for obtaining biofuels using microalgae biomass, thermochemical processes (pyrolysis, HTL, gasification) have proven to be processed with higher viability, because they use all biomass. However, because of the complexity of the biomass (lipids, carbohydrates , and proteins), the obtained biofuels from direct thermochemical conversion have large amounts of heteroatoms (oxygen, nitrogen , and sulfur). As a solution, catalyst-based processes have emerged as a sustainable solution for the increase in biocrude production. This paper's objective is to present a comprehensive review of recent developments on catalyst mediated conversion of algal biomass. Special attention will be given to operating conditions, strains evaluated, and challenges for the optimal yield of algal-based biofuels through pyrolysis and HTL.

Epilepsy is one of the most common disorders of the central nervous system, impacting nearly 50 million people around the world. Heterogeneous in nature, epilepsy presents in children and adults alike. Currently, surgery is the only treatment that can cure epilepsy. However, not all individuals are eligible or have successful outcomes. Difficulty in accessing samples of human brain tissue along with advances in sequencing technology have driven researchers to investigate sampling liquid biopsies in blood, serum, plasma, and cerebrospinal fluid within the context of epilepsy. Liquid biopsies provide minimal or non-invasive sample collection approaches and can be assayed relatively easily across multiple time points, unlike tissue-based sampling. Various efforts have investigated circulating nucleic acids from these samples including microRNAs, cell-free DNA, transfer RNAs, and long non-coding RNAs. Here, we review nucleic acid-based liquid biopsies in epilepsy to improve understanding of etiology, diagnosis, prediction, and therapeutic monitoring.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

Stable-isotope dimethyl labeling is a highly reactive and cost-effective derivatization procedure that could be utilized in proteomics analysis. In this study, a liquid chromatography-tandem mass spectrometry in multiple reaction monitoring mode (LC-MS-MRM) platform for the quantification of kiwi allergens was first developed using this strategy. Three signature peptides for target allergens Act d 1, Act d 5, and Act d 11 were determined and were derivatized with normal and deuterated formaldehyde as external calibrants and internal standards, respectively. The results showed that sample preparation with the phenol method provided comprehensive protein populations. Recoveries at four different levels ranging from 72.5–109.3% were achieved for the H-labeled signature peptides of Act d 1 (SPA1-H) and Act d 5 (SPA5-H) with precision ranging from 1.86–9.92%. The limit of quantification (LOQ) was set at 8 pg mL–1 for SPA1-H and at 4 ng mL–1 for SPA5-H. The developed procedure was utilized to analyze seven kinds of hand-made kiwi foods containing 0.0175–0.0515 mg g–1 of Act d 1 and 0.0252–0.0556 mg g–1 of Act d 5. This study extended the applicability of stable-isotope dimethyl labeling to the economical and precise determination of food allergens and peptides.

The research aims to discover the natural occurrence of patulin (PAT) in selected citrus fruits from the central cities of Punjab and Pakistan's Northern cities. Total 2970 samples of twelve citrus fruits; kinnow, orange, grapefruits, bitter orange, mausami, red blood, pineapple, sweet orange, rough lime, sweet lime, kagzi lime and lemon were examined using liquid chromatography fitted with UV detector. The limit of detection (LOD) and quantification limit was 0.04 and 0.12 µg/kg, respectively. The results have shown that 56% of samples of citrus fruits from Punjab's central cities, Pakistan, were discovered to be infected from PAT. The elevated amounts of PAT ranging from 0.04 to 1150 µg/kg were found in citrus fruit samples from Multan cities. Furthermore, 31.7% of samples of citrus fruits from Northern cities of Pakistan were discovered to be infected with PAT, and the elevated amounts were found ranging from 0.04-320 µg/kg from Swat city. About 22.1% of samples of citrus fruits have levels of PAT greater than the suggested limits established by the European Union (EU). PAT's dietary intake levels ranged from 0.10-1.11 µg/kg bw/day from the central cities of Punjab, Pakistan, and 0.13-1.93 µg/kg bw/day were documented from Northern cities of Pakistan.

Liquid manipulation by photoisomerization attracts recent attentions as a new active droplet control method for micro-chemical analysis. Such a non-inverse manipulation can be realized by a use of solution liquid of surfactant that exhibits the \emph{cis}-\emph{trans} isomerization triggered by light irradiation with a specific wavelength such as ultraviolet light. Since the isomerization is accompanied by changes in fluid properties, a light irradiation on one of liquid-air interfaces of a liquid column in a tube would generate differences in the wettability accompanied between the both sides of the finite liquid column. Although this technique has been demonstrated experimentally by Muto et al. (\emph{Euro.~Phys.~J.~Special Topics}, {\bf 226}, 2016, 1199--1205), its dynamics and developments of each isomer distribution are not understood. In order to reveal the liquid-column migration phenomenon, we have performed numerical simulations of air-liquid two-phase flows and its scalar transport of the isomer, using the Volume-of-Fluid method in conjunction with the Continuum-Surface-Force model and Continuous-Species-Transfer method. We validated present results by comparison with experimental result in terms of the migration distance of the liquid column. We confirmed a termination of the liquid-column migration occurs when the \emph{cis} isomer distribution reaches the non-irradiated region. The migration speed was less dependent on the liquid-column length and was proportional to the tube diameter.

Engineered nanomaterials (ENMs) are of significant relevance due to their unique properties, which have been exploited for widespread applications. Cerium oxide nanoparticles (CeO2-NPs) are one of most exploited ENM in the industry due to their excellent catalytic and multi-enzyme mimetic properties. Thus, toxicological effects of these ENMs should be further studied. Acute and subchronic toxicity of CeO2-NPs were assessed. First an in vitro multi-dose short-term (24h) toxicological assessment was performed in three different cell lines: A549 and Calu3, representing the lung tissue, and 3T3 as an interstitial tissue model. After that, a sub-chronic toxicity assessment (90 days) of these NPs was carried out on a realistic and well stablished reconstituted primary human airway epithelial model (MucilAir™), cultured at the Air-Liquid Interface (ALI), to study long-term effects of these particles. Results showed minor toxicity of CeO2-NPs in acute exposures. However, in subchronic exposures, cytotoxic and inflammatory responses were observed in the human airway epithelial model after 60 days of exposure to CeO2-NPs. These results suggest that acute toxicity approaches may underestimate the toxicological effect of some ENM, highlighting the need of subchronic toxicological studies in order to accurately assess the toxicity of ENM and their cumulative effects in the organism.

Researchers have developed and used several three-dimensional (3D) culture systems, including spheroids, organoids, and tumoroids. Drug resistance is a crucial issue involving recurrence in cancer patients. Many studies on anticancer drugs have been done in 2D culture systems, where-as 3D cultured tumoroids have many advantages for assessing drug sensitivity and resistance. Here, we aim to investigate whether Cisplatin (a DNA crosslinker), Imatinib (a multiple tyro-sine kinase inhibitor), and 5-Fluorouracil (5-FU: an antimetabolite) alter tumoroid growth of metastatic colorectal cancer (mCRC). To establish a liquid-based 3D multiplexing reporter assay system, LuM1 (a murine mCRC cell line) was stably transfected with the Mmp9 promoter-driven ZsGreen reporter gene, which was designated as LuM1/m9 cells and cultured in NanoCulture Plate (NCP), a 3D culture device. The larger tumoroids were not sensitive to Cisplatin and ex-pressed ABCG2 (a marker of cancer stem cells, a.k.a. a drug efflux transporter), whereas smaller cell-aggregates were more sensitive to Cisplatin. Both Imatinib and Cisplatin significantly in-creased tumoroid growth (larger than 300 μm2) and Mmp9 promoter activity and were not cytotoxic to the mCRC tumoroids. On the other hand, 5-FU was cytotoxic to the tumoroids and significantly inhibited tumoroid growth, although not completely. Thus, platinum resistance and imatinib resistance in mCRC were modeled using the liquid-based 3D cultured tumoroid system. The tumoroid culture is useful and easily accessible for the assessment of drug sensitivity and resistance.

In-plane electro-optical switching (IPS) is a natural feature of a conventional planar aligned display cell based on deformed helix ferroelectric liquid crystal effect (DHFLC-effect) with sub-wavelength helix pitch if the tilt angle close to 40 degrees.

The ionic liquid A327H+Cl- is generated by reaction of the tertiary amine A327 (industrial mixture of tri-octil and tri-decyl amines) and hydrochloric acid solutions. Further, the extraction of Au(III) by A327H+Cl- ionic liquid under various variables, including metal and ionic liquid concentrations, has been investigated. Results indicate that A327H+AuCl4- is formed, by an exothermic (ΔHº= -3 kJ/mol) reaction, in the organic solution. Aqueous ionic strength influences the formation constants values and the specific interaction theory (SIT) is used to estimate the interaction coefficient between AuCl4- and H+. Gold (III) is stripped using thiocyanate media, and from the strip solutions, gold is precipitated as gold nanoparticles.

Glioblastoma is the most common and malignant primary brain tumor. Despite a century of research efforts, the survival of patients has not significantly improved. Currently, diagnosis is based on neuroimaging techniques followed by histopathological and molecular analysis of resected or biopsied tissue. A recent paradigm shift in diagnostics ranks the molecular analysis of tissue samples as the new gold standard over classical histopathology, thus correlating better with the biological behavior of glioblastoma and clinical prediction, especially when a tumor lacks the typical hallmarks for glioblastoma. Liquid biopsy aims to detect and quantify tumor-derived content, such as nucleic acids (DNA/RNA), circulating tumor cells (CTC), or extracellular vesicles (EV) in biofluids, mainly blood, cerebrospinal fluid (CSF), or urine. Liquid biopsy has the potential to overcome the limitations of both neuroimaging and tissue-based methods to identify early recurrence and to differentiate tumor progression from pseudoprogression, without the risks of repeated surgical biopsies. This review highlights the origins and time-frame of liquid biopsy in glioblastoma and points to recent developments, limitations and challenges of adding liquid biopsy to support the clinical management of glioblastoma patients.

We review a modern differential geometric description of the fluid isotropic motion and featuring it the diffeomorphism group structure, modelling the related dynamics, as well as its compatibility with the quasi-stationary thermodynamical constraints. There is analyzed the adiabatic liquid dynamics, within which, following the general approach, there is explained in detail, the nature of the related Poissonian structure on the fluid motion phase space, as a semidirect Banach groups product, and a natural reduction of the canonical symplectic structure on its cotangent space to the classical Lie-Poisson bracket on the adjoint space to the corresponding semidirect Lie algebras product. We also present a modification of the Hamiltonian analysis in case of the isotermal liquid dynamics. We study the differential-geometric structure of the adiabatic magneto-hydrodynamic superfluid phase space and its related motion within the Hamiltonian analysis and invariant theory. In particular, we construct an infinite hierarchies of different kinds of integral magneto-hydrodynamic invariants, generalizing those before constructed in the literature, and analyze their differential-geometric origins. A charged liquid dynamics on the phase space invariant with respect to an abelian gauge group transformation is also investigated, some generalization of the canonical Lie-Poisson type bracket is obtained.

Alterations in the carnitine shuttle system may be an indication of the presence of cancer. As such, in-depth analyses of this pathway in different malignant tumors could be important for the detec-tion and treatment of this disease. The current study aims to assess the profiles of carnitine and acylcarnitines in gliomas with respect to their grade, the presence of isocitrate dehydrogenase (IDH) mutations, and 1p/19q co-deletion. Brain tumors obtained from 19 patients were sampled on-site using solid-phase microextraction (SPME) immediately following excision. Analytes were desorbed and then analyzed via liquid chromatography-high resolution mass spectrometry. The results showed that SPME enabled the extraction of carnitine and 22 acylcarnitines. An analysis of the correlation factor revealed presence of two separate clusters: short-chain and long chain car-nitine esters. Slightly higher carnitine and acylcarnitine concentrations were observed in the higher malignancy tumor samples (high vs low grade), and in those samples with worse projected clinical outcomes (without vs with IDH mutation; without vs with 1p/19q co-deletion). Thus, the proposed chemical biopsy approach offers a simple solution for on-site sampling that enables sample preservation, thus supporting comprehensive multi-method analyses.

Solid porous materials, like zeolites, have been widely used in a variety of fields such as size and shape-selective absorption/separation and catalysis because of their porosity. But there are few liquid materials exhibit permanent porosity. Porous liquids are a novel material that combine the properties of fluidity and permanent porosity. It has potential applications in many fields such as gas separation, storage and transport. Herein, we report a novel Type 1 porous liquid prepared based on Silicalite-1. The pore size of this porous liquid was determined by positron annihilation lifetime spectroscopy (PALS), and the CO2 capacities was determined by the intelligent gravimetric analyser (IGA). The unique properties of this porous liquid can promote its application in many fields such as gas storage and transport.

Liquid marbles are defined as hydrophilic liquid droplets that are coated with hydrophobic powdered materials. Till now, the behaviour of liquid marbles has been studied for triphasic systems comprising of the constituent hydrophilic phase, the hydrophobic coating and ambient air. In this article, we report the dynamics of aqueous droplets of varying pH (i.e. acidic, neutral and basic, respectively) moving under the influence of gravity in commonly available mustard oil. We find that the said dynamics could be divided into four parts: (i) formation of hanging aqueous droplets from the top surface of oil, (ii) oblate spheroid droplets moving at constant velocity due to viscous drag, (iii) distant repulsive interactions between two droplets due to “reverse Cheerios effect” and (iv) final impact between the two droplets explained by viscoelastic sliding friction over a compliant surface. This work would be of great interest to researchers working in the domain of interfacial phenomena like oil exploration, biomedical engineering, food technology and towards the realization of droplet-based microfluidic computational platforms for “more than Moore’s” paradigm in the domain of unconventional computation.

Radical changes in the idea of the organization of the intracellular space that occurred in the early 2010-s made it possible to consider the formation and functioning of the so-called membrane-less organelles (MLOs) based on a single physical principle: the liquid-liquid phase separation (LLPS) of biopolymers. Weak nonspecific inter- and intramolecular interactions of disordered polymers, primarily of intrinsically disordered proteins and RNA, play a central role in the initiation and regulation of these processes. On the other hand, in some cases, the "maturation" of MLOs can be accompanied by the "liquid-gel” phase transition, where other types of interactions can play a significant role in reorganization of their structure. In this work, we conducted a bioinformatics analysis of the propensity of the proteomes of two membrane-less organelles formed in response to stress in the same compartment, nucleolus, for spontaneous phase separation and looked at their intrinsic disorder predispositions. These nucleolar MLOs, amyloid bodies (A-bodies) formed in the response to acidosis and heat shock and nuclear stress bodies (nSBs), are characterized by the partially overlapping composition, but show different functional activities and morphologies. We show that the proteomes of these nucleolar biocondensates are differently enriched in proteins, many of with high potential for spontaneous LLPS that correlates with different morphology and function of these organelles. The results of these analyses allowed us to evaluate the role of weak interactions in the formation and functioning of these important organelles.

In this study, we report a detailed experimental and theoretical investigation of three glycols, namely ethane-1,2-diol, 2-methoxyethan-1-ol and 1,2-dimethoxy ethane. For the first time, the X-Ray spectra of the latter two liquids was measured at room temperature, and they were compared with the newly measured spectrum of ethane-1,2-diol. The experimental diffraction patterns were interpreted very satisfactorily with molecular dynamics calculations, and suggest that in liquid ethane-1,2-diol most molecules are found in gauche conformation, with intramolecular hydrogen bond between the two hydroxyl groups. Intramolecular H-bonds are established in the mono-alkylated diol, but the interaction is weaker. The EDXD study also evidences strong intermolecular hydrogen-bond interactions, with short O···O correlations in both systems, while longer methyl-methyl interactions are found in 1,2-dimethoxy ethane. X-Ray studies are complemented by micro Raman investigations at room temperature and at 80°C, that confirm the conformational analysis predicted by X-Ray experiments and simulations.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

The transport of indium(III), from HCl solutions, across a supported liquid membrane in flat-sheet configuration was investigated, being the carrier the ionic liquid HA324H+Cl- (derived from the tertiary amine Hostarex A324 and hydrochloric acid). Different variables affecting the metal transport: hydrodynamic conditions in the source and receiving phases, metal and HCl concentrations in the source phase, and carrier concentration in the membrane phase, were investigated. Also the transport of indium(III) using carriers of various nature: ionic liquids, alcohol, ketone, phosphine oxide and phosphoric ester, was compared. The metal transport was modelled describing the transport mechanism as: diffusion across the source diffusion layer, a fast interfacial chemical reaction, and diffusion of the InCl4--carrier complex through the membrane support. Diffusional parameters for the transport of indium(III), from the experimental data and the model, were estimated.

Background: Liquid biopsies are revolutionary tools to detect tumor-specific genetic alterations in body fluids, and cell-free DNA (cfDNA) can be used for molecular diagnosis in cancer patients. In brain tumors cerebrospinal fluid (CSF) cfDNA might be more informative than plasma cfDNA. Here, we assess the use of CSF cfDNA in pediatric embryonal brain tumors (EBT) for molecular diagnosis. Methods: CSF cfDNA of pediatric patients with medulloblastoma (n=18), ATRT (n=3), ETMR (n=1), CNS NB FOXR2 (n=2) and pediatric EBT NOS (n=1) (mean cfDNA concentration 48 ng/mL; range 4-442 ng/mL) and matched tumor genomic DNA were sequenced by WES, and/or a targeted sequencing approach, to determine single nucleotide variations (SNVs)/copy number alterations (CNA). A specific capture covering transcription start sites (TSS) of genes of interest was used for nucleosome footprinting in CSF cfDNA. Results: 15/25 CSF cfDNA samples yielded informative results, with informative CNA and SNVs in 11 and 15 cases, respectively. For cases with paired tumor and CSF cfDNA WES (n=15), a mean of 83 (range 1-160) shared SNVs was observed, including SNVs in classical medulloblastoma genes such as SMO and KMT2D. Interestingly, tumor-specific SNVs (mean 18; range 1-62) or CSF-specific SNVs (mean 5; range 0-25) were observed suggesting clonal heterogeneity. The TSS panel resulted in differential coverage profiles across all 112 studied genes in 7 cases, indicating distinct promoter accessibility. Conclusion: CSF cfDNA sequencing yielded informative results in 60% of cases (15/25), with WES feasible in 83% (15/18). These results pave the way for implementation of these novel approaches for molecular diagnosis and minimal residual disease monitoring.

Head and neck squamous cell carcinomas (HNSCCs) develop from the mucosa of the oral cavity, pharynx, and larynx. The methylation levels of Septin 9 (SEPT9) and short stature homeobox 2 (SHOX2) genes in ccfDNA are considered pan-cancer biomarkers and have shown prognostic value in preliminary reports in HNSCC. Liquid biopsy is a non-invasive procedure that collects tumor-derived molecules including circulating cell-free DNA (ccfDNA). Here, we developed a ddPCR-based assay to detect the DNA methylation levels of plasma circulating SEPT9 and SHOX2 in patients with HNSCC. We first set up the assay on commercial methylated and un-methylated DNA. Then, the dynamic changes of the methylation levels of SEPT9 and SHOX2 were quantified in 20 patients during the follow-up. The results highlighted: i) the capability of the ddPCR-based assay in detecting very low copies of methylated molecules; ii) the significant decrease in methylation levels of SEPT9 and SHOX2 in plasma of HNSCC patients at the first time points of follow-up respect to T0; iii) a different trend of longitudinally DNA methylation variations associable to the clinicopathological features of the patients. The absolute quantification of the methylation levels of SEPT9 and SHOX2 in HNSCC may be used for risk stratification and disease monitoring.

The simplest possible structural transition that an electronic system can undergo is Wigner crystallization. The aim of this short review is to discuss the main aspects of three recent experimets on the one dimensional Wigner molecule, starting from scratch. To achieve this task, the Luttinger liquid theory of weakly and strongly interacting fermions will be shortly addressed, together with the basic properties of carbon nanotubes that are require. Then, the most relevant properties of Wigner molecules will be addressed, and finally the experiments will be described.

The thermal lubrication of an entangled polymeric liquid in wall-driven shear flows between parallel plates is investigated by using a multiscale hybrid method coupling molecular dynamics and the hydrodynamics (i.e., the synchronized molecular dynamics method). The temperature of the polymeric liquid rapidly increases due to viscous heating once the drive force exceeds a certain threshold value. The rheological properties of the polymeric liquid drastically change at around the critical drive force. In the weak viscous-heating regime, the conformation of polymer chains is dominated by the local shear flow so that the anisotropy of the bond orientation tensor grows as the drive force increases. However, in the large viscous-heating regime, the conformation dynamics is dominated by the thermal agitation of polymer chains so that the bond orientation tensor recovers more uniform and random structures as the drive force increases, even though the local shear flows are further enhanced. Remarkably, these counter-intuitive transitional behaviors give an interesting re-entrant transition in the stress--optical relation, where a linear formalism in the stress--optical relation approximately holds even though each of the macroscopic quantities behaves nonlinearly. The robustness of the linear stress--optical relation is also confirmed in the spatiotemporal evolution at the hydrodynamic level.

Most oral squamous cell carcinomas (OSCCs) arise from oral epithelial dysplasia; however, there is no useful marker for early OSCC detection, likely owing to the inability to continuously observe the carcinoma sequence. We aimed to establish an experimental model to observe changes in the sequential expression pattern of mRNA and protein in the same rat using liquid-based cytology techniques. Cytology specimens were collected from a 4-nitroquinoline 1-oxide-induced rat tongue cancer model at 2, 5, 8, 11, 14, 17, and 21 weeks. We examined candidate biomarker expression using immunocytochemistry and quantitative real-time PCR. The percentage of positively stained nuclei was calculated as the labeling index (LI). All rats had OSCC of the tongue at 21 weeks. Brd4 (Brd4), Myc (c-Myc), and Tp53 (p53) mRNA levels were upregulated during progression from negative for intraepithelial lesion or malignancy to SCC. Brd4- and c-Myc-LI were increased in low- and high-grade squamous intraepithelial lesions and SCC specimens. p53-LI was significantly increased in SCC specimens. Our experimental model allowed the observation of sequential morphological changes and mRNA and protein expression patterns in the same rat during carcinogenesis. By reducing the false negative rate, BRD4 and c-Myc can be useful markers for the early detection of OSCC.

The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

Short chain quinones (SCQs) have been identified as potential drug candidates against mitochondrial dysfunction, which is largely dependent on their reversible redox characteristics of the active quinone core. We recently synthesized a SCQ library of > 148 naphthoquinone derivatives and identified 16 compounds with enhanced cytoprotection compared to the clinically used benzoquinone idebenone. One of the major drawbacks of idebenone is its high metabolic conversion in the liver, which significantly restricts is therapeutic activity. Therefore, this study assessed the metabolic stability of the 16 identified naphthoquinone derivatives 1-16 using hepatocarcinoma cells in combination with an optimized reverse-phase liquid chromatography (RP-LC) method. Most of the derivatives showed significantly better stability than idebenone over 6 hours (p < 0.001). By extending the side-chain of SCQs, increased stability for some compounds was observed. Metabolic conversion from the derivative 3 to 5 and reduced idebenone metabolism in the presence of 5 were also observed. These results highlight the therapeutic potential of naphthoquinone-based SCQs and provide essential insights for future drug design, prodrug therapy and polytherapy, respectively.

Background: Liquid biopsy is widely recognised as an efficient diagnostic method in oncology for disease detection and monitoring. Though examination of circulating tumor cell (CTC) is mostly implemented for assessment of genomic aberrations, need of complex methodologies for their detection has impeded its acceptance in low resource settings. We evaluated the cell free DNA (cfDNA) as a liquid biopsy tool and investigated its utility in breast cancer patients. Methods: Total cell free DNA was extracted from plasma of breast cancer patients (n=167) with median follow up of more than 5 years, at various stages of the disease. Quantitative PCR was performed to estimate the copy numbers of two fractions of ALU repetitive elements (ALU 115 and ALU 247) and DNA Integrity (DI) was calculated as the ratio of ALU 247/115. Mutations in TP53 and PIK3CA in the cfDNA was estimated by next-gen sequencing (NGS) in a subset of samples. Association of the levels of both the ALU fragments with various clinico-pathological factors and disease-free survival at various stages were examined. Nomogram models were constructed with clinical variables and ALU 247 levels to predict disease-free survival and best performing model was evaluated by decision curve analysis. Results: DI and ALU 247 levels were significantly lower (p<0.0001) in the post-operative plasma when compared to their pre-surgery levels. DI and ALU 247 were found to be significantly higher in patients with metastasis (p<0.05). Patients with higher levels of ALU 247 in their post-operative plasma had significantly poor disease-free survival (p=0.005). Higher level of ALU 247 in circulation also correlated with low tumor-infiltrating lymphocytes (TIL) within their primary tumors in the ER-negative breast cancer subtype (p=0.01). Cox proportional hazard analysis confirmed ALU 247 as an independent variable of disease-free survival both in univariate and multivariate analysis [HR 1.3 (95% CI 1.047 to 1.613, p= 0.017)]. Nomogram model showed addition of ALU 247 with other variables significantly improved (C-index-0.823) the predictive ability of the model. Conclusion: Our results confirm the utility of cfDNA as an evolving liquid biopsy tool for molecular analysis. Evaluation of larger fragment of cfDNA estimated through ALU 247 can provide vital information concurrent with the pathological process of disease evolution in breast cancer and warrants expansion to other cancer types.

Frequency combs (FCs)—spectra containing equidistant coherent peaks—have enabled researchers and engineers to measure the frequencies of complex signals with high precision thereby revolutionising the areas of sensing, metrology and communications and also benefiting the fundamental science. Although mostly optical FCs have found widespread applications thus far, in general FCs can be generated using waves other than light. Here, we review and summarise recent achievements in the emergent field of acoustic frequency combs (AFCs) including phononic FCs and relevant acousto-optical, Brillouin light scattering and Faraday wave-based techniques that have enabled the development of phonon lasers, quantum computers and advanced vibration sensors. In particular, our discussion is centred around potential applications of AFCs in precision measurements in various physical, chemical and biological systems in conditions, where using light, and hence optical FCs, faces technical and fundamental limitations, which is, for example, the case in underwater distance measurements and biomedical imaging applications. This review article will also be of interest to readers seeking a discussion of specific theoretical aspects of different classes of AFCs. To that end, we support the mainstream discussion by the results of our original analysis and numerical simulations that can be used to design the spectra of AFCs generated using oscillations of gas bubbles in liquids, vibrations of liquid drops and plasmonic enhancement of Brillouin light scattering in metal nanostructures. We also discuss the application of non-toxic room-temperature liquid-metal alloys in the field of AFC generation.

Tissue programmed death ligand-1 (PD-L1) protein expression is predictive of immune checkpoint inhibitor (ICI) benefit. However, tissue PD-L1 can be fraught with tissue acquisition and heterogeneity limitations. Plasma testing can overcome these limitations. However, the overall survival (OS) predictive benefit of plasma PD-L1 assays have not been well characterized. Patients with stage IV non-small cell lung cancer (NSCLC) and plasma cfRNA PD-L1 by PCR expression were identified and assessed for OS. 16 patients treated with front-line ICI-based regimens were assessed and represented a real-world patient population with over half with a performance status of 2 or greater. 10 contemporaneous patients at the same institution treated with chemotherapy alone were also identified and assessed. With a median follow-up of 33 months, median OS was 13 months with a 30% 3-year OS for the ICI treated patients compared to a median OS of 3 months and a 10% 3-year OS for those treated with chemotherapy alone. Comparative log-rank test p-value = 0.014 and a hazard ratio 0.376 (95%-CI 0.134-1.057). Plasma cfRNA PD-L1 was associated with a statistically significant survival benefit from ICI-based treatment compared to chemotherapy in the first line treatment of a real-world patient population of advanced NSCLC.

Liquid crystal elastomers (LCEs) are shape morphing materials whose large and reversible shape transformation results from the coupling between the mobile anisotropic properties of liquid crystal (LC) units and the rubber elastic of polymer networks. Their shape changing behaviors under the stimuli are largely directed by LC orientations, and therefore various strategies have been developed to spatially modulate the LC alignments. But most of the methods suffer from complex fabrication technologies or intrinsic limitations in applicability. To address this issue, programmable complex shape changes in some types of LCEs, such as polysiloxane side-chain LCEs or thiol-acrylate main-chain LCEs, etc, have been achieved by using a mechanical alignment programming process coupled with two-step crosslinking. Here, we report a polysiloxane main-chain LCE with programmable 2D and 3D shape changing performances achieved by mechanically programming the polydomain LCE between the two crosslinking steps. The resulting LCEs exhibited reversible thermal induced shape transformation between the initial and programmed shapes due to the two-way memory between the first network structure and the second network structure. Our work would be potential for expanding the applications of LCE materials in actuators, soft robotics and smart structures where arbitrary and easily programmed shape morphings are needed.

The research aims to discover the natural occurrence of patulin (PAT) in selected citrus fruits from the central cities of Punjab and Pakistan's Northern cities. Total 2970 samples of twelve citrus fruits; kinnow, orange, grapefruits, bitter orange, mausami, red blood, pineapple, sweet orange, rough lime, sweet lime, kagzi lime and lemon were examined using liquid chromatography fitted with UV detector. The limit of detection (LOD) and quantification limit was 0.04 and 0.12 µg/kg, respectively. The results have shown that 56% of samples of citrus fruits from Punjab's central cities, Pakistan, were discovered to be infected from PAT. The elevated amounts of PAT ranging from 0.04 to 1150 µg/kg were found in citrus fruit samples from Multan cities. Furthermore, 31.7% of samples of citrus fruits from Northern cities of Pakistan were discovered to be infected with PAT, and the elevated amounts were found ranging from 0.04-320 µg/kg from Swat city. About 22.1% of samples of citrus fruits have levels of PAT greater than the suggested limits established by the European Union (EU). PAT's dietary intake levels ranged from 0.10-1.11 µg/kg bw/day from the central cities of Punjab, Pakistan, and 0.13-1.93 µg/kg bw/day were documented from Northern cities of Pakistan

Since 2000, caffeine is used as citrate salt of caffeine for treatment of apnea of prematurity. However, it remained elusive if caffeine citrate has a direct function in the respiratory epithelium, potentially as modulator for ciliary beat frequency (CBF) regulation in human respiratory cells (hRECs). Here, we studied the mechanism of action of caffeine citrate on the respiratory epithelium on hRECs derived from healthy donors and individuals with cystic fibrosis (CF) cultured under air-liquid-interface (ALI) conditions. CBF analyses of hRECs were performed by high-speed video microscopy. In the presence of caffeine, hRECs show a significant increase in CBF over ciliary base frequency (CBFb), demonstrating a direct influence of caffeine on ciliary function. We also demonstrate a specific action of caffeine at ryanodine receptor (RYR) channels, mediating calcium efflux from intracellular stores to increase CBF. We describe a novel pharmacological effect of caffeine citrate - direct increase of CBF of primary hRECs cultured at ALI. Caffeine citrate has certain advantages over other methylxanthines: it was shown to have stable plasma concentration, longer half-life, and is better tolerated than e.g. theophylline. We conclude that caffeine citrate therapy might be suitable strategy to treat respiratory diseases with compromised mucociliary clearance.

At the molecular level, aging is often accompanied by dysfunction of stress-induced membrane-less organelles (MLOs) and changes in their material state. In this work, we analyzed the proteins included in the proteome of stress granules (SGs) and P-bodies for their tendency to transform the material state of these MLOs. Particular attention was paid to proteins whose gene expression changes during replicative aging. It was shown that the proteome of the studied MLOs practically does not differ in the analyzed characteristics and consists of completely or partially intrinsically disordered proteins, 30 - 40% of which are potentially capable of liquid-liquid phase separation (LLPS). At the same time, the proportion of proteins capable of spontaneous LLPS is relatively small, which indicates the leading role of nucleic acids in the biogenesis of these membrane-less organelles. Proteins whose gene expression changes during the transition of human cells to a senescent state make up about 20% of the studied proteomes. There is a statistically significant increase in the number of positively charged proteins in both datasets studied compared to the complete proteomes of these organelles. An increase in the relative content of DNA-, but not RNA-binding proteins, was also found in the stress-granules dataset with senescence-related processes. Among SG proteins potentially involved in senescent processes, there is an increase in the abundance of potentially amyloidogenic proteins compared to the whole proteome. The hnRPDL protein has the highest degree of disorder and highest propensity for LLPS among such proteins, which allows us to consider it as “potentially dangerous.” Proteins common to SGs and P bodies, potentially involved in processes associated with senescence, form clusters of interacting proteins. The largest cluster is represented by RNA-binding proteins involved in RNA processing and translation regulation. These data indicate that SG proteins, but not proteins of P-bodies, are more likely to transform the material state of MLOs. Furthermore, these MLOs can participate in processes associated with aging in a coordinated manner.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

At the beginning of the 21st century, it became obvious that radical changes had taken place in the concept of living matter and, in particular, in the concept of the organization of intracellular space. The accumulated data testify to the essential importance of phase transitions of biopolymers (first of all, intrinsically disordered proteins and RNA) in the spatiotemporal organization of the intracellular space. Of particular interest is the stress-induced reorganization of the intracellular space. Examples of organelles formed in response to stress are nuclear A-bodies and nuclear stress granules. The formation of these organelles is based on LLPS of intrinsically disordered proteins and non-coding RNA. Despite the overlapping composition and similar mechanism of formation, these organelles have different functional activities and physical properties. In this review, we will focus our attention on these MLOs and describe their functions, structure, and mechanism of formation.

A recent paradigm shift in diagnostics of medulloblastoma allows the distinction of four major groups defined by genetic data rather than histology. This new molecular classification correlates better with prognosis and will allow better clinical management for therapies targeting druggable mutations, but also offers a new combination of monitoring tumor development in real-time and treatment response by sequential liquid biopsy. This review highlights recent developments after a century of milestones in neurosurgery, radio- and chemotherapy, but also controversial theories on the cell of origin, animal models and the use of liquid biopsy.

The objective of this paper is to investigate the convergence of coupling-parameter expansion-based solutions to Ornstein-Zernike equation in liquid state theory. The analytically solved Baxter's adhesive hard sphere model is analyzed first using coupling-parameter expansion. It is found that the expansion provides accurate approximations to solutions - including the liquid-vapor phase diagram - in most parts of the phase plane. However, it fails to converge in the region where the model has only complex solutions. Similar analysis and results are, then, obtained using analytical solutions within the mean spherical approximation for the hard-core Yukawa potential. Next, convergence of the expansion is analyzed for the Lennard-Jonnes potential using an accurate density-dependent bridge function in the closure relation. Numerical results are presented which show convergence of correlation functions, compressibility versus density profiles, etc., in the single as well as two phase regions. Computed liquid-vapor phase diagrams, using two independent schemes employing the converged profiles, compare excellently with simulation data. Results obtained for the generalized Lennard-Jonnes potential, with varying repulsive exponent, also compare well with simulation data. All these results together establish the coupling-parameter expansion as a practical tool for studying single component fluid phases modeled via general pair-potentials.

As non-operative management (NOM) of esophageal and rectal cancer is becoming more prevalent, blood-biomarkers such as circulating tumor DNA (ctDNA) may provide clinical information in addition to endoscopy and imaging to aid in treatment decisions following chemotherapy and radiation therapy. In this feasibility study, we prospectively collected plasma samples from locally advanced esophageal (n=3) and rectal cancer (n=2) patients undergoing multimodal neoadjuvant therapy to assess the feasibility of serial ctDNA monitoring throughout neoadjuvant therapy. Using the DIDA-Seq error-correction method, we serially interrogated plasma cell-free DNA at 28-41 tumor-specific genomic loci throughout therapy and in surveillance with an average limit of detection of 0.016% mutant allele frequency. In both rectal cancer patients, ctDNA levels were persistently elevated following total neoadjuvant therapy with eventual detection of clinical recurrence prior to salvage surgery. Among the esophageal cancer patients, ctDNA levels closely correlated with tumor burden throughout and following neoadjuvant therapy, which was associated with a pathologic complete response in one patient. In this feasibility study, patient and tumor-specific ctDNA levels correlated with clinical outcomes throughout multi-modality therapy suggesting that serial monitoring of patient ctDNA has the potential to serve as a highly sensitive and specific biomarker to risk-stratify esophageal and rectal cancer patients eligible for NOM. Further prospective investigation is warranted.

We evaluated hexadecyltrimethylammonium bromide (HTAB) for use in radio frequency (RF) applications in which liquid crystals (LCs) are used in layered structures that have various cell gap conditions. HTAB is a surfactant that can self-align vertically on the surface of indium tin oxide (ITO) substrates, and can induce homeotropic alignment of the LCs. For implementing RF devices with HTAB and LCs, we should consider limitations caused by the design conditions which are different from conventional liquid crystal displays such as cell gap. We quantified the concentration of HTAB ([HTAB]) that is necessary to form and maintain a sufficiently dense vertical alignment of 5CB (4-Cyano-4'-pentylbiphenyl). The required [HTAB] for full-homeotropic alignment was proportional to the cell gap until it was too large to support the transfer of the surface alignment to the LC, due to the weak anchoring nature of HTAB. We also showed the phase-change characteristic of the LC mixture depended on [HTAB] for the design of RF devices driven by light or heat. This work may help to guide the development of new approaches to designing efficient RF devices that use LCs.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

Capacitance measurements have been extensively used to measure the anchoring extrapolation length L at a nematic-substrate interface. These measurements are extremely delicate because the value found for L often critically depends on the sample thickness and the voltage range chosen to perform the measurements. Several reasons have been proposed to explain this observation, such as the presence of inhomogeneities in the director distribution on the bounding plates or the variation with the electric field of the dielectric constants. In this paper I propose a new method to measure Lp that takes into account this second effect. This method is more general than that proposed in Murauski et al. Phys. Rev. E 71, 061707 (2005) because it does not assume that the anchoring angle is small and that the anchoring energy is of the Rapini-Papoular form. This method is applied to a cell of 8CB treated for planar unidirectional anchoring by photoalignment with the azobenzene dye Brilliant Yellow. The role of flexoelectric effects and the shape of the anchoring potential are discussed.

The evidence is presented for the long-range previtreous changes of two static properties: dielectric constant ( ) and its strong electric field related counterpart - the nonlinear dielectric effect (NDE). Notable is the evidence for the functional characterizations of (T) temperature changes by the ‘Mossotti Catastrophe’ formula, and NDE vs. T evolution by the relations resembling one developed for critical liquids. The analysis of dynamic properties based on the activation energy index excluded the Vogel-Fulcher-Tammann (VFT) relation as a validated tool for portraying the evolution of the primary relaxation time. Such a result questions the commonly applied ‘Stickel operator’ routine as the reliable tool for determining the dynamic crossover temperature. It is worth stressing that the strong electric field radically affects the distribution of relaxation times, the form of the evolution of the primary relaxation time as well as the fragility. Obtained results support the concept of a possible semi-continuous phase transition hidden below Tg. Studies were carried out in supercooled squalene, the material with extremely low electric conductivity, strongly elongated molecule, and vitally important for biology and medicine related issues.

After surgery, oral cavity healing occurs in a hostile environment and requires proper oral care and hygiene to accelerate recovery. The aim of the current study is to investigate and compare the bioreactivity characteristics of chlorhexidine based (CHX) mouth rinse and a novel bone bioactive liquid (BBL) mouth rinse on oral healing within seven days application post-surgery. A randomized, double blind clinical trial conducted in 81 patients. The mouth rinses were applied twice a day for a period of 7 days. The visual analog scale (VAS) protocol was applied to measure pain index. Early wound healing score (EHI) was determined in evaluate the oral cavity healing progress. No adverse effects were observed using the mouth washes, but CHX resulted in teeth staining. CHX and BBL were sufficient to reduce pain over a period of 7 days. However, the BBL group demonstrated a statistically significant reduction in VAS stating day 4. Relative to CHX group, the EHI scores were significantly higher in the BBL group, independent from the tooth location. No gender differences were observed in both VAS and EHI scores. Relative to the commercially available CHX, BBL mouth rinse reduced pain and accelerated oral cavity healing. Suggesting an improvements of oral cavity microenvironment at the wound site that mediates soft tissue regeneration.

I review the solution of QCD in two spacetime dimensions. Following the analysis of Baluni, for a single flavor the model can be analyzed using Abelian bosonization. The theory can be analyzed in strong coupling, when the quarks are much lighter than the gauge coupling. In this limit, the theory is given by a Luttinger liquid.

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

By the use of the tertiary amine A327 and 1 M HCl solution as precursors, the ionic liquid A327H+Cl- was generated and used to investigate its performance in the transport of Au(III) form hydrochloric acid medium. The influence of the stirring speed (600-1800 min-1), ionic liquid concentration (1.25-50% v/v) in the membrane phase and gold concentration (0.01-0.15 g/L) in the feed phase on metal transport have been investigated. An equation which included both equilibrium and kinetics parameters was derived, and the membrane diffusional resistance (Δm) and feed phase diffusional resistance (Δf) was estimated as 9.5x106 s/cm and 307 s/cm, respectively. At carrier concentrations in the 5-50% v/v range and gold concentrations in the 0.01-0.15 g/L range, metal transport is controlled by diffusion of metal species through the feed boundary layer, whereas at the lowest carrier concentrations, membrane diffusion is predominant. From the receiving solutions, gold can be recovered as gold nanoparticles.

Breast cancer (BC) is the most common cancer diagnosed in women worldwide. Approximately 70% of BC patients have the luminal subtype, which expresses hormone receptors (HR+). Adjuvant endocrine treatments are the standard of care for HR+/HER2- BC patients. Over time, approximately 30% of those patients develop endocrine resistance and metastatic disease. Cyclin-dependent kinase inhibitors (CDKi) in combination with an aromatase inhibitor or fulvestrant have demonstrated superior efficacies in increasing progression-free survival, with a safe toxicity profile, in HR+/HER2- metastatic BC patients. CDKi blocks kinases 4/6, preventing G1/S cell cycle transition. However, not all patients respond to CDKi, and those who do respond ultimately develop resistance to the combined therapy. Studies in tumour tissues and cell lines have tried to elucidate the mechanisms underlying this progression, but there are still no conclusive data. Over the last few years, liquid biopsy has contributed relevant information. Circulating tumour materials are potential prognostic markers for determining patient prognosis in metastatic luminal BC, for monitoring disease and for treatment selection. This review outlines the different studies performed using liquid biopsy in patients with HR+ metastatic BC treated with CDKi plus endocrine therapy. We focus mainly on those studies that describe possible resistance mechanisms in circulating tumour-derived material.

The naturally occurring dipeptide carnosine (β alanyl L histidine) specifically attenuates tumor growth. Here, we asked whether other small imidazole containing compounds also affect viability of tumor cells without affecting non-malignant cells, and whether formation of histamine is involved. Patient-derived fibroblasts and glioblastoma cells were treated with carnosine, L alanyl L histidine (LA-LH), ß alanyl L alanine, L histidine, histamine, imidazole, β alanine and L alanine. Cell viability was assessed by cell-based assays and microscopy. The intracellular release of L histidine and formation of histamine was investigated by High Performance Liquid Chromatography coupled Mass Spectrometry. Whereas carnosine and LA LH inhibited tumor cell growth with minor effects on fibroblasts, L-histidine, histamine and imidazole affected viability in both cell types. Compounds without imidazole moiety did not diminish viability. In the presence of LA LH but not in the presence of carnosine a significant rise of intracellular amounts of histidine was detected in all cells. Formation of histamine was not detectable in the presence of carnosine, LA LH or histidine. In conclusion, the imidazole moiety of carnosine contributes to its anti-neoplastic effect, which is also seen in the presence of histidine and LA LH. Despite histamine had a strong effect on cell viability, formation of histamine is not responsible for the effects on cell viability of carnosine, LA LH and histidine.

Respiratory tract epithelium infection plays a primary role in Nipah virus (NiV) pathogenesis and transmission. Knowledge about infection dynamics and host responses to NiV infection in respir-atory tract epithelia is scarce. Studies in non-differentiated primary respiratory tract cells or cell lines indicate insufficient interferon (IFN) responses. However, studies are lacking to determin-ing complex host response patterns in differentiated respiratory tract epithelia to understand NiV replication and spread in swine. Here we characterized infection and spread of NiV in differenti-ated primary porcine bronchial epithelial cells (PBEC) cultivated at the air-liquid-interface (ALI). After the initial infection of only a few apical cells, lateral spread for 12 days with epithelium disruption was observed without releasing substantial amounts of infectious virus from the api-cal or basal sides. Deep time course proteomics revealed pronounced upregulation of genes re-lated to type I/II- IFN, immunoproteasomal subunits, TAP-mediated peptide transport and MHC I antigen presentation. Spliceosomal factors were downregulated. We propose a model in which NiV replication in PBEC is slowed by a potent and broad type I/II-IFN host response with con-version from 26S proteasomes to immunoproteasomal antigen processing and improved MHC I presentation for adaptive immunity priming. NiV induced cytopathic effects could reflect the focal release of cell-associated NiV, which may contribute to efficient airborne viral spread between pigs.

On the system Au(III)-HCl-A324H⁺Cl^-, liquid-liquid extraction experiments were used to define the extraction equilibrium and the corresponding extraction constant, and the facilitated transport of this precious metal, from HCl solutions, across a flat-sheet supported liquid membrane was investigated, using the ionic liquid as carrier, as a function of hydrodynamic conditions, concentration of gold(III) (0.01-0.1 g/L), and HCl (0.5-6 M) in the feed phase, and carrier concentration (0.023-0.92 M) in the membrane. An uphill transport equation was derived considering aqueous feed boundary layer diffusion and membrane diffusion as controlling steps. The aqueous diffusional resistance (Δf) and the membrane diffusional resistance (Δm) were estimated from the proposed equation, being their values 241 s/cm an 9730 s/cm, respectively. The performance of the present carrier was compared against results yielded by other ionic liquids, and also it was investigated the influence that other metals had on gold(III) transport both from binary or quaternary solutions. Gold was finally recovered from receiving solutions as zero valent gold nanoparticles.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

The local and global order in dense packings of linear, semi-flexible polymers of tangent hard spheres are studied by employing extensive Monte Carlo simulations at increasing volume fractions. Chain stiffness is controlled by a tunable harmonic potential for the bending angle whose intensity dictates the rigidity of the polymer backbone as a function of the bending constant and equilibrium angle. The studied angles range from acute to obtuse ones, reaching the limit of rod-like polymers. We analyze how packing density and chain stiffness affect the ability of chains to self-organize at the local and global levels. The former corresponds to crystallinity as quantified by the Characteristic Crystallographic Element (CCE) norm descriptor, while the latter is computed through the scalar orientational order parameter. In all cases, we identify the critical volume fraction for the phase transition and gauge the established crystal morphologies, developing a complete phase diagram as a function of packing density and equilibrium bending angle. A plethora of structures is obtained, ranging from random hexagonal closed packed morphologies of mixed character and almost perfect face centered cubic (FCC) and hexagonal close-packed (HCP) crystals at the level of monomers, to nematic mesophases, with prolate and oblate mesogens at the level of chains. For rod-like chains, hysteresis is observed between the establishment of long-range nematic order and crystallization, while for right-angle chains both transitions are synchronized. A comparison is also provided against the analogous packings of monomeric and fully flexible chains of hard spheres.

Introduction: Circulating tumor DNA (ctDNA) is newly diagnosed tumor DNA that can easily represent a tumor’s genetic and epigenetic change. Pheochromocytomas (PCCs) and Paragangliomas (PGLs) are rare tumors of adrenal gland tissue that have the potential to be detected by ctDNA. We aimed to study the potential of the methylation status of RDBP, SDHB, and SDHC genes in ctDNA of PCCs/PGLs patients as a diagnostic biomarker. Materials and Methods: Clinical data, fresh frozen tissue, the blood of 12 PCCs/PGL patients, and the blood of 12 age/sex-matched normal patients were collected. The methylation status of RDBP, SDHB, and SDHC was compared between cases and controls by MS-HRM analysis. Results: Amongst six promoter regions of RDBP, SDHB, and SDHC, promoter methylation quantification of SDHCa and RDBPb was significantly different between PCCs/PGLs and controls. SDHCa was methylated in 49.93% of PCCs/PGLs cases vs. 8.33 % of control samples, p-value: 0.026, area under curve AUC=0.757, and RDBPb in 74.9% of PCCs/PGLs cases vs. 25.0% of control samples, p-value: 0.032, AUC=0.750. Conclusions: This study suggests the ctDNA potential for a less invasive source of tumor epigenetic modification in PCCs/PGLs malignancies. The SDHCa and RDBPb hypermethylation warrant further exploration as diagnostic tools for PCCs/PGLs.

Unmetamorphosed carbonaceous chondrites provide important information concerning the formation and evolution of organic matter, such as amino acids. However, terrestrial contamination remains a valid concern when investigating the organic inventory of meteorites that have fallen to Earth. Accordingly, JAXA’s Hayabusa2 and NASA’s OSIRIS-REx have been launched with the task of returning uncontaminated C-type asteroid material to Earth. The successful Hayabusa2 mission has a very limited sample size (5.4 g). Therefore, many conventional compound specific techniques will struggle to detect amino acids above detection limit with available sample amounts (~several mg to 10’s of mg) being much smaller than those typically used. Here a novel method utilizing ultrahigh performance liquid chromatography-Orbitrap-mass spectrometry is validated and applied to very small meteorite samples, thus providing an approach that can overcome the small sample size constraints of sample return missions. The method is highly sensitive, enabling the detection of amino acids in the carbonaceous chondrites Murchison (2.28 mg) and Orgueil (2.30 mg). Furthermore, quantitation was possible for many of the detected amino acids in Murchison and Orgueil. Using the data presented here, both the amino acid reservoirs of Murchison and Orgueil and the potential application of this method to sample return samples are discussed.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature range depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential - one for a slow and another one for a fast decay of the repulsion at small distances. In the first case two different patterns - for example clusters or stripes - occur with the same probability for some range of the chemical potential. For fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for sufficiently low temperature.

Pancreatic ductal adenocarcinoma (PDAC) is expected to be the second cause of cancer death by 2022. For nearly 80% of patients, diagnosis occurs at an advanced, non-surgical stage, making such patients incurable. Gemcitabine is still an important component in PDAC treatment and is most often used as a backbone to test new targeted therapies and there is, to date, no routine biomarker to predict its efficacy. Samples from a phase III randomized trial were used to develop trough a large approach based on blood-based liquid biopsy, transcriptome profiling, and machine learning, a 9 gene predictive signature for gemcitabine sensitivity. Patients with a positive test (41.6%) had a significantly longer progression free survival (PFS) (3.8 months vs. 1.9 months p=0.03) and a longer overall survival (OS) (14.5 months vs. 5.1 p<0.0001). In multivariate analyses, this signature was independently associated with PFS (HR=0.5 (0.28-0.9) p=0.025) and OS (HR=0.39 (0.21-0.7) p=0.002).

High circulating concentrations of the gut microbiota-derived metabolite trimethylamine N-oxide (TMAO) are significantly associated with the risk of obesity and type 2 diabetes (T2D). We aimed at evaluating the impact of glycemic control and bariatric surgery on circulating concentrations of TMAO and its microbiota-dependent intermediate, γ-butyrobetaine (γBB), in newly diagnosed T2D patients and morbidly obese subjects. An additional experiment was carried out in eight male C57BL/6J mice fed a Western-type diet for twelve weeks. The strategy for glycemic control in the T2D patients significantly improved the HbA1c concentrations without producing changes in the estimated glomerular filtration rate. However, the plasma TMAO and γBB concentrations were significantly increased following the glycemic control in T2D patients. Bariatric surgery was very effective in reducing weight in obese subjects. Nevertheless, the surgery reduced plasma γBB concentrations without affecting TMAO concentrations and the estimated glomerular filtration rate. Neither diet-induced obesity nor insulin resistance were associated with circulating TMAO and γBB concentrations in mice. Our findings do not support that glycemic control or bariatric surgery improve the circulating concentrations of TMAO in newly diagnosed T2D and morbidly obese patients. The contribution of antidiabetic drugs to gut microbiota composition could explain TMAO elevations in treated T2D subjects.

An overview of the chemical compounds forming the rare smectic T phases is cited with references to the historical context. Thermodynamics (transition temperatures, enthalpies) along with the factors (stereochemical constraints, electrostatic interactions, aliphatic chain stacking, intermolecular forces) contributing to the adoption of tetragonal scaffolds are also discussed. Characteristic optical microscopy textures and x-rays diffraction patterns are presented. In parallel, a comparison of the geometrical parameters such as distances between atoms, molecular areas, volumes, and lattice parameters with the closest two-dimensional and three-dimensional organizations, is performed.

To determine promethazine (PMZ) and its metabolites promethazine sulfoxide (PMZSO) and monodesmethyl-promethazine (Nor1PMZ) in swine muscle, fat, kidney, and liver, a sample preparation and high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis method were established and validated. The sample was extracted with 0.1% formic acid-acetonitrile, and the extract was purified with acetonitrile-saturated n-hexane. After concentration by rotary evaporation, the extract was re-dissolved in 0.1% formic acid-water and acetonitrile (80:20, v/v). The HPLC-MS/MS column used was a Waters Symmetry C18 (100 mm × 2.1 mm i.d., 3.5 μm), with 0.1% formic acid-water and acetonitrile as the mobile phase, and the target compounds were determined by positive ion scan and multiple reaction monitoring. PMZ and Nor1PMZ were quantified with deuterated promethazine (PMZ-d6) as the internal standard, while PMZSO was quantified by external standard method. The limits of detection (LOD) and limits of quantification (LOQ) of PMZ and PMZSO in muscle, liver, and kidney spiked samples were 0.05 μg/kg and 0.1 μg/kg, respectively, while those of Nor1PMZ were 0.1 μg/kg and 0.5 μg/kg, respectively. The LOD and LOQ of analytes in fat spiked sample were 0.05 μg/kg and 0.1 μg/kg, respectively. The sensitivity of this method reaches or exceeds its presented in previous reports. The analytes PMZ and PMZSO showed good linearity within the range of 0.1 μg/kg to 50 μg/kg, while Nor1PMZ showed good linearity within the range of 0.5 μg/kg to 50 μg/kg, with correlation coefficients (r) greater than 0.99. The recoveries of the target compounds in the sam-ples were between 81.73% and 107.17%, and the precision ranged from 1.78% to 10.47%. This study developed for the first time an HPLC-MS/MS method for the determination of PMZ and its metabolites PMZSO and Nor1PMZ in four swine edible tissues, comprehensively covered target tissues of monitoring object, which is applicable for monitoring veterinary drug residues in ani-mal-derived foods and ensuring food safety.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

Fanconi anemia (FA) patients display an exacerbated risk of oral squamous cell carcinoma (OSCC) and precursor lesions at young ages, mainly at the oral cavity. As patients have defects in DNA repair mechanisms, standard-of-care treatments to OSCC such as radiotherapy and chemotherapy give rise to severe toxicities. New methods for early diagnosis are urgently necessary to allow treatments in early disease stages and achieve better clinical outcomes. We have conducted a prospective, longitudinal study whereby liquid biopsies from sixteen lesion/tumor-free patients were analyzed for the presence of mutations in cancer genes. DNA from saliva and plasma were sequentially collected and deep-sequenced, and the clinical evolution followed during a median time of around 2 years. In 9/16 FA patients we detected mutations in cancer genes (mainly TP53) with molecular allele frequencies (MAF) down to 0.07 %. Importantly, all patients having mutations and clinical follow-up data after mutation detection (n=6) developed oral precursor lesions or OSCC. Lead-time between mutation detection and tumor diagnosis ranged from 23 to 630 days. Strikingly, FA patients without mutations display significantly lower risk of developing precursor lesions or OSCC. Therefore, our diagnostic approach could help to stratify FA patients into risk groups, which would allow closer surveillance for OSCC or precursor lesions.

We report herein the synthesis of siloxane-functionalized CBP molecules (4,4’-bis(carbazole)-1,1′-biphenyl) for liquid optoelectronic applications. The room-temperature liquid state is obtained through a convenient functionalization of the molecules with heptamethyltrisiloxane chains via hydrosilylation of alkenyl spacers. The synthesis comprises screening of metal-catalyzed methodologies to introduce alkenyl linkers into carbazoles (Stille and Suzuki Miyaura cross-couplings), incorporate the alkenylcarbazoles to dihalobiphenyls (Ullmann coupling), and finally introduce the siloxane chains. The used conditions allowed the synthesis of the target compounds, despite the high reactivity of the alkenyl moieties bound to π-conjugated systems toward undesired side reactions such as polymerization, isomerization, and hydrogenation. The features of these solvent-free liquid CBP derivatives make them potentially interesting for fluidic optoelectronic applications.

So far, poly(L-lactic acid), PLLA, nanosheets proved to be promising for wound healing. Such biodegradable materials are easy-to-prepare, bio-friendly, cost-effective, simple to apply and were shown to protect burn wounds and facilitate their healing. At the same time, certain metal ions are known to be essential for wound healing, which is why this study was motivated by the idea of incorporating PLLA nanosheets with Zn2+ ion containing nanoparticles. Upon being applied on wound, such polymer nanosheets should release Zn2+ ions, which is expected to improve wound healing. The work thus focused on preparing PLLA nanosheets embedded with several kinds of Zn-containing nanoparticles, their characterization and ion-release behavior. ZnCl2 and ZnO nanoparticles were chosen as model particles with different solubility in water, both types showing similar ion release dynamics in liquid medium with pH around 7.4.

One objective of this paper is to investigate bifurcation of solutions of Ornstein-Zernike equation in liquid state theory for the gas-liquid coexistence region of simple fluids. The analysis uses a discrete form of the Ornstein-Zernike equation in real space, together with a closure relation which provides nearly self consistent thermodynamic properties of fluids governed by interaction potentials like the Lennard-Jones potential. Accurate asymptotic forms of correlation functions are incorporated in the real space algorithm so as to mitigate the influence of cutoff length used in the discrete approximations. It is found that there is no spinodal on the vapor side on a sub-critical isotherm. But there are fold bifurcation points on the vapor and liquid sides together with a 'no-real-solution-region' in between. This is followed by a region of negative compressibility extending up to the spinodal on the liquid side. The emerging picture is quite similar to that in the case of the hypernetted-chain-closure. It is also found that complex solutions connect the physical solutions that exist outside the 'no-real-solution-region' as well as in region of negative compressibility. The second objective of the paper, in the light of bifurcation scenario, is to evolve an interpretation of the coupling-parameter expansion of correlation functions pertaining to the region of negative compressibility. It is shown that the expansion provides an accurate description of results of the restricted ensembles, implied in mean field theories and simulation methods. Bifurcation of singlet density to inhomogeneous distributions at a spinodal is also established using a simple equation, which uses the direct correlation function. Thus the paper reestablishes the fact that restriction to a homogeneous singlet density is the root cause of all inconsistencies found in the gas-liquid coexistence region.

Fungi belong to the species with the highest biodiversity and high potential for use in biotechnology and industry. Therefore, their long-term quality conservation is very important and it is necessary to continuously develop new methods and improve existing methods. Currently, cryopreservation appears to be the best available technique for the preservation of fungi. This study summarises the latest trends and advances in fungal cryopreservation over the last 7 years, i.e. findings from scientific publications from 2017 to 2023 dealing with cryopreservation of both basidiomycetes and non-basidiomycete fungi. The work analyzed the studied organisms and the cryopreservation method used, focused on the use of new procedures and modifications of existing methods; summarized the conditions for successful cryopreservation, such as cryopreservation time and temperature, as well as the substrate and cryoprotectant used.

Recently, there has been increasing attention toward inhaled nanoparticles (NPs) to develop in-halation therapies for diseases associated with the pulmonary system and investigate the toxic ef-fects of hazardous environmental particles on human lung health. Taking advantage of microfluidic technology for cell culture applications, lung-on-a-chip devices with great potential in replicating the lung air-blood barrier (ABB) have opened new research insights in preclinical pathology and therapeutic studies associated with aerosol NPs. Surprisingly, the air interface in such devices, which makes them tremendously unique among the other common liquid-based cellular mi-crosystems and enables exposure of cultivated cells to the drug/toxic aerosols, has been largely disregarded. Accordingly, there exists a significant research gap in the comprehensive under-standing of the NPs’ dynamics in the lung-on-a-chip devices, which is momentous to control the injection of aerosols to the target area and attain a desired physiochemical efficacy. To address this research gap, a numerical parametric study is presented to provide a deep insight into the dynamic behavior of the airborne NPs in a gas-liquid dual-channel lung-on-a-chip device with a porous membrane separating the channels. A finite element multi-physics model is developed to enable a particle tracing investigation simultaneously in both air and medium phases to replicate the in vivo conditions avoiding laborious and costly experimental trials. The results include the impact of fluid flow as well as geometrical properties on the distribution, deposition, and translocation of the NPs with diameters ranging from 10 nm to 900 nm in the lung-on-a-chip. The obtained results strongly suggest the aerosol injection of NPs instead of the aqueous solution for more efficient deposition on the substrate of the air channel and higher translocation to the media channel. The current study proposes to optimize the affecting parameters to control the injection and delivery of aerosol par-ticles into the lung-on-chip device depending on the objectives of biomedical investigations and provides optimized values for some specific cases. Therefore, this study can assist scientists and researchers in complementing their experimental investigation in future preclinical studies on pulmonary pathology associated with inhaled hazardous and toxic environmental particles, as well as therapeutic studies for developing inhalation drug delivery.

The process of ultrasonic atomization involves a series of dynamic/topological deformations of free surface, though not always, of a bulk liquid (initially) below the air. This study focuses on such dynamic interfacial alterations realized by changing some acousto-related operating conditions, including ultrasound excitation frequency, acoustic strength or input power density, and the presence/absence of a “stabilizing” nozzle. High-speed, high-resolution imaging made it possible to qualitatively identify four representative transitions/demarcations: 1) the onset of a protrusion on otherwise flat free surface; 2) the appearance of undulation along the growing protuberance; 3) the triggering of emanating beads fountain out of this foundation-like region; and 4) the induction of droplets bursting and/or mist spreading. Quantitatively examined were the two-parameters specifications—on the degrees as well as induction—of the periodicity in the protrusion-surface and beads-fountain oscillations, detected over wider ranges of driving/excitation frequency (0.43–3.0 MHz) and input power density (0.5–10 W/cm2) applied to the ultrasound transducer of flat surface on which the nozzle was mounted or not. The resulting time sequence of images processed for the extended operating ranges, regarding the fountain structure pertaining in particular to recurring beads, confirms the wave-associated nature, i.e., their size “scalability” to the ultrasound wavelength, predictable from the traveling wave relationship. The thresholds in acoustic conditions for each of the four transition states of the fountain structure have been identified—notably, the onset of plausible “bifurcation” in the chain-beads diameter below a critical excitation frequency.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

In recent years, various optical measurement technologies such as far-infrared spectroscopy, low-frequency Raman spectroscopy, optical Kerr effect spectroscopy, and two-dimensional Raman-terahertz spectroscopy have developed vigorously. By comparing the complementary aspects detected by various linear and nonlinear spectroscopic techniques, a coherent picture emerges from studies of dynamics in water. Numerous molecular dynamics experiments and theoretical investigations have demonstrated low-frequency molecular motions in liquid water. For example, intermolecular hydrogen bond vibration, molecular reorientation motion, and the interaction between molecule/ionic solute and hydrogen bond all occur in the THz region, which are closely related to their physical/chemical properties and structural dynamics. However, precise probing of various modes of motion is difficult due to the complexity of the collective and cooperative motion of molecules and the spectral overlap of related modes. With the development of THz optical technology, current state-of-the-art THz sources can generate pulsed electric fields with peak intensities on the order of ~MV/cm. Such strong fields make it possible to use THz waves as the driving light source for nonlinear polarization of the medium, which in turn leads to the development of the emerging terahertz Kerr effect (TKE) spectroscopy technique. Many low-frequency molecular motion modes, such as the collective directional motion of molecules and the cooperative motion under the constraint of weak intermolecular interactions, are resonantly excited to unprecedentedly strong amplitudes driven by the THz electric field. Thereby the collected responses are increased. The TKE technique thus creates an interesting prospect for investigating low-frequency dynamics in these media. In view of this, this paper firstly summarizes the research work on the measurement mechanism of TKE spectroscopy by taking the solid material without low-frequency molecular dynamics process as an example. Starting from the principle of TKE technology and the exploration of the properties of solid matter using this technology, its application in the exploration of low-frequency molecular dynamics of liquid water and aqueous solutions is introduced. Liquid water is considered the building block of life and possesses many extraordinary physical and biochemical properties. Its hydrogen bonding network plays a crucial role in these properties. It is generally believed that the ability of water to form complex hydrogen-bonding networks is the main reason for its various kinetic and thermodynamic properties that are different from other liquids. However, the exact structure of the hydrogen-bonding network, the spatial extent of its existence, and the associated timescale are not known. And the relevant spectral information of the basic properties of the reaction water is still not known. Therefore, it is of great significance to evaluate the hydrogen bond-related kinetic properties of liquid water by optical means.

Growth environment greatly alters many facets of pathogen physiology, including pathogenesis and antimicrobial tolerance. The importance of host-mimicking environments for attaining an accurate picture of pathogen behaviour is widely recognised. Whilst this recognition has translated into the extensive development of artificial cystic fibrosis (CF) sputum medium, attempts to mimic the growth environment in other respiratory disease states have been completely neglected. The composition of the airway surface liquid (ASL) in different pulmonary diseases is far less well characterised than CF sputum, making it very difficult for researchers to model these infection environments. In this review we discuss the components of human ASL, how different lung pathologies affect ASL composition, and how different pathogens interact with these components. This will provide researchers interested in mimicking different respiratory environments with the information necessary to design a host-mimicking medium, allowing for better understanding of how to treat pathogens causing infection in these environments.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

Cellular biomolecular condensates termed ribonucleoprotein (RNP) granules often are enriched in messenger RNA (mRNA) molecules relative to the surrounding cytoplasm. Yet, the spatial localization and diffusion of mRNAs in close proximity to phase separated RNP granules is not well understood. In this study, we performed single molecule fluorescence imaging experiments of mRNAs in live cells in the presence of two types of RNP granules, stress granules (SG) and processing bodies (PB), which are distinct in their molecular composition and function. We developed a photobleaching- and noise-corrected colocalization imaging algorithm that was employed to determine the accurate positions of individual mRNAs relative to the granule’s boundaries. We found that mRNAs are often localized at granule boundaries, an observation consistent with recently published data. We suggest that mRNA molecules become spontaneously confined at the RNP granule boundary similar to the adsorption of polymer molecules at liquid-liquid interfaces, which is observed in various technological and biological processes. We also suggest that this confinement could be due to a combination of intermolecular interactions associated with, first, the screening of a portion of the RNP granule interface by the polymer and, second, electrostatic interactions due to a strong electric field induced by a Donnan potential generated across the thin interface.

A formula for the turbulent Prandtl number is derived in terms of local variables available from two-equations turbulence models. The derivation is a direct consequence of the expected square additivity of the molecular and turbulent parameters defining the effective viscosity and the effective conductivity. The formula does not degenerate and leads to a Kays like formulation if approximated. Its utility and its limitation are discussed.

Although there are a large number of databases available for regulatory elements, bottleneck has been created by the lack of bioinformatics tools for predicting types of mechanisms underlying actions of regulatory elements. To reduce the gap, we developed ARabidopsis Transcription regulatory Factor Domain-domain interaction Analysis Tool- Liquid-liquid phase separation (LLPS), Oligomerization, GO analysis (ART FounDATion-LOG), a useful toolkit for protein-nucleic acid interactions (PNI) and protein-protein interactions (PPI) analysis based on domain-domain interaction (DDI). LLPS, protein oligomerization, structural properties of protein domains, and protein modifications are major components in orchestrating spatio-temporal dynamics of PPI and PNI. Our goal is to integrate PPI/PNI information into development of prediction model for identifying important genetic variants in peach. The program unified inter-database relational keys by protein domains for facilitating inference from the model species. Key advantage of the program lies in the integrated information of related features: LOG, structural characterization of domain (e.g. domain linker, intrinsically disordered regions, DDI, domain-motif (peptide) interaction, beta-sheet and transmembrane helices), and post-translational modification. We provided simple tests to demonstrate how to use the program. The program may be applied to other eukaryotic organisms. The program codes and data are freely available for download at and https://sourceforge.net/projects/artfoundation-log/.

(200 words) Imidazolium ionic liquids containing acetylacetone, thenoyltrifluoroacetone, or 8-hydroxyquinoline, respectively, were used as the extracting agents for the separation of traces of iron (III) from its aqueous solutions with or without citric and oxalic acids. The results show that 8-hydroxyquinoline in imidazolium ionic liquids extract iron quantitatively from all the tested solutions including complexing ones, regardless indications of unexpected iron behavior/speciation.

This work investigated the effect of temperature and acid or alkalis chemical activation by pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) on the yield of bio-oil, hydrocarbon content of bio-oil, and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, KOH and HCl activation, in laboratory scale. The acidity of bio-oils and aqueous phases determined by AOCS methods, while the chemical composition of bio-oils and aqueous phase by GC-MS and FT-IR. The bio-char characterized by XRD. For the activation with KOH, the XRD analysis identified the presence of Kalicinite (KHCO3), the dominant crystalline phase in bio-char, while an amorphous phase was identified in bio-chars for the activation with HCl. The yield of bio-oil, for the pyrolysis of Açaí seeds activated with KOH, varied between 3.19 and 6.79 (wt.%), showing a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while the acidity of aqueous phase lies between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the pyrolysis experiments activated with HCl, the yield of bio-oil varied between 2.13 and 3.37 (wt.%), decreasing linearly with temperature, while that of gas phase varied between 17.91 and 37.94 (wt.%), increasing linearly with temperature. The acidity of bio-oil varied between 127.1 and 218.5 mgKOH/g, increasing with temperature, showing that higher temperatures did not favor the yield of bio-oil and bio-oils acidity. For the chemical activation with KOH, the FT-IR analysis of bio-oils identified the presence of chemical groups characteristics of hydrocarbons and oxygenates, while that of aqueous phase only groups characteristics of oxygenates. For the chemical activation with HCl, the FT-IR analysis of bio-oil and aqueous phases identified only the presence of groups characteristics of oxygenates. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with HCl activation, the GC-MS of bio-oil identified only the presence of oxygenates. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons while activation with HCl produced bio-oils with only oxygen compounds.

Background: The detection of the EGFR T790M (T790M) mutation in non-small cell lung cancer (NSCLC) patients who progressed under treatment with first- or second-generation EGFR-tyrosine kinase inhibitors (TKIs) is important to offer a subsequent therapy with a third-generation EGFR-TKI. Liquid biopsy is a powerful tool to determine the T790M mutation status. Several liquid biopsy platforms with varying degrees of accuracy are available to test for T790M mutations and sensitivities may differ among these methods. Methods: As no standard exists for the testing of T790M mutation in liquid biopsy, we performed a collaborative study to describe and compare the sensitivity of different in-house liquid biopsy platforms for the detection of the T790M mutation, EGFR exon 19 deletion (del19) and EGFR L858R mutation (L858R) across multiple participating laboratories in seven Central and Eastern European countries. Results: Of the 25 invited laboratories across Central and Eastern Europe, 21 centers participated and received 10 plasma samples spiked with cell-line DNA containing the T790M, del19, or L858R mutation in different concentrations. In-house PCR-based and NGS-based methods were used accordingly, and results reported as in routine clinical practice. Two laboratories, which used the AmoyDx® EGFR 29 Mutations Detection Kit (AmoyDx) with Cobas® cfDNA Sample Preparation Kit and QX200 Droplet Digital PCR (ddPCR) with the QIAamp Circulating Nucleic Acid Kit identified all ten samples correctly. Cobas® EGFR Mutation Test v2 (Cobas), the NGS methods, and the IdyllaTM detection method used in this study performed within the known sensitivity range of each detection method. Conclusions: If a negative result was obtained from methods with lower sensitivity (e.g. Cobas), repeated liquid biopsy testing and/or tissue biopsy analysis should be performed whenever possible, with the aim of identifying T790M-positive patients to allow them to receive the optimal second-line treatment with a third-generation EGFR TKI.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

Abstract: The ability to detect several types of cancer using a non-invasive, blood-based test holds the potential to revolutionize oncology screening. We mined tumor methylation array data from the Cancer Genome Atlas (TCGA) covering 14 cancer types and identified two novel, broadly oc-curring methylation markers at TLX1 and GALR1. To evaluate their performance as a general-ized blood-based screening approach, along with our previously reported methylation bi-omarker, ZNF154, we rigorously assessed each marker individually or combined. Utilizing the TCGA methylation data and applying logistic regression models within each individual cancer type, we found that the three-marker combination significantly increased the average area under the ROC curve (AUC) across the 14 tumor types compared to single markers (p= 1.158e-10; Friedman test). Furthermore, we simulated dilutions of tumor DNA into healthy blood cell DNA and demonstrated increased AUC of combined markers across all dilution levels. Finally, we evaluated assay performance in bisulfite sequenced DNA from patient tumors and plasma, in-cluding early-stage samples. When combining all three markers the assay achieved 100% sensi-tivity and specificity, as demonstrated in lung cancer plasma samples. In patient plasma from hepatocellular carcinoma, ZNF154 alone yielded the highest combined sensitivity and specificity values averaging 68% and 72%, whereas multiple markers could achieve higher sensitivity or specificity, but not both. Altogether this study presents a comprehensive pipeline for the identifi-cation, testing and validation of multi-cancer methylation biomarkers with a considerable poten-tial for detecting a broad range of cancer types in patient blood samples.

68Ga-based radiopharmaceuticals are routinely used for PET imaging of multiple types of tumors tumours. Gallium-68 is commonly obtained from 68Ge/68Ga generators, which are limited in the quantity of activity produced. Alternatively, gallium-68 can easily be produced on a cyclotron using liquid targets. In this study we optimized the GMP production of [68Ga]GaFAPI-46 using gallium-68 produced from a standard medical cyclotron using liquid targets. Starting from the published synthesis and quality control procedures described for other 68Ga-based radiopharmaceuticals, we have validated the synthesis process and the analytical methods to test the quality parameters of the final product to be used for routine clinical studies. [68Ga]GaFAPI-46 was successfully produced with high radiochemical purity and yield using an IBA Synthera® Extension module. Gallium chloride was cyclotron produced on a medical cyclotron using a liquid target with an activity of 4.31 ± 0.36 GBq at the end-of-purification (EOP). Analytical methods were established and validated meeting Ph. Eur. standards. Fully GMP production was also validated in three consecutive batches, producing 2.50 ± 0.46 GBq of [68Ga]Ga-FAPI-46 at the end-of-synthesis (EOS), with 98.94 ± 0.72% radiochemical purity by radio-HPLC. Quality was maintained for up to 3 h after the EOS. Production of [68Ga]GaFAPI-46 was performed and validated using a standard medical cyclotron with liquid targets. Quality control parameters (e.g. sterility, purity, and residual solvents) conform to Eur. Phar. and shelf life of 3 h was established. Activity of [68Ga]GaFAPI-46 produced is substantially higher than the one obtained with generators enabling a better response to the clinical need for this radiopharmaceutical.

The pharmacokinetic profile of fat-soluble vitamins A, E, K1, and D3 co-administered with liquid paraffin or water in an experimental rat model was investigated. Animals received a solution of the four vitamins orally through a probe, followed 10 minutes later by the administration of either the liquid paraffin product dissolved in water (Emuliquen Simple®) or water (control). Vitamin formulations were 20, 50, 0.30 and 0.10 mg/kg for vitamins A, E, K1, and D3, respectively. Blood samples were collected before dosing and at 0.17, 1, 2, 4, 8, and 24 hours post-dosing. Vitamin concentrations were quantified by liquid chromatography coupled with mass spectrometry. No relevant differences in the absorption of vitamins in terms of AUC0-last (area under the curve up to the last measurable concentration) or Cmax in the absence or presence of co-administration of the liquid paraffin product were observed. The difference of these parameters between the treatment groups for all vitamins was in the range of bioequivalence (≤ 20%). The liquid paraffin-based laxative product did not interfere with the absorption of vitamins A, E, K1, and D3 that are ingested in the diet, which is clinically relevant due to the high prevalence of functional constipation in children and adults.

A large body of evidence, replicated in many mouse models of Alzheimer Disease (AD), demonstrated the therapeutic efficacy of oral rapamycin. Administration of m-TOR inhibitors (mTOR-Is), early after the clinical onset, greatly diminished cognitive impairment, amyloid angiopathy, intracellular beta Amyloid and neurofibrillary tangles load. The daily intake of rapamycin has always been 2.24g/Kg/24h. In humans the maximal tolerated oral dose is a few milligrams/day, and at this dosage patients are severely immunosuppressed. Thanks to rapalogs’ scarce CNS-related side effects, we administered intracerebroventricularly (ICV) high doses of the mTOR-I everolimus in a mouse model of AD (3xTg-AD) without significant systemic effects. The instability of the liquid formulation at body temperature (BT) made the treatment very short. Nevertheless, the efficacy of the treatment was high and much longer lasting than expected. In order to set up a thermostable, translational liquid formulation of mTOR-Is, we loaded everolimus in distearoylphosphatidylethanolamine-polyethylene glycol 2000 (DSPE-PEG2000) micelles by the thin layer method. The formulation we obtained maintained over 95% of activity after 14 days at BT. We can envision short, potentially periodic ICV treatments in AD patients which replicate results obtained on animal models. The treatment could benefit also Tuberous Sclerosis and Multiple Sclerosis patients.

Abstract: Filipendula ulmaria, commonly known as meadowsweet, is a wild herbaceous flowering plant widely distributed in Europe. A range of salicylic acid derivatives and flavonol glycosides have been previously associated with the antirheumatic and diuretic properties of F. ulmaria. In the present work, an hydroalcoholic extract of F. ulmaria aerial parts was extensively profiled using an efficient NMR-based dereplication strategy. The approach involves fractionation of the crude extract by centrifugal partition chromatography (CPC), ¹³C NMR analysis of the fractions, 2D-cluster mapping of the whole NMR dataset and finally, structure elucidation using a natural metabolite database, validated by 2D NMR data interpretation and liquid chromatography coupled to mass spectrometry. The chemodiversity of the aerial parts was quite broad, with 28 compounds unambiguously identified, belonging to various biosynthetic classes. The F.ulmaria extract and CPC fractions were screened for their potential to improve skin epidermal barrier function and also skin renewal properties using in vitro assays performed on Normal Human Epidermal Keratinocytes. Fractions containing quercetin, kaempferol glycosides, ursolic acid, pomolic acid, naringenin, β-sitosterol, and tellimagrandins I and II were found to be responsible for the up-regulation of genes related to skin barrier function, epidermal renewal and stress responses. This research is significant as it could provide a natural solution for improving hydration and skin renewal properties.

Guava (Psidium guajava L.) is a common fruit tree that grows in several tropical and subtropical parts of the world. The aim of this study was to employ the use of liquid-liquid fractionation to investigative the comparative antibacterial potential of crude extracts of Guava leaves and bark against selected food isolates; Escherichia coli, Pseudomonas aeruginosa, Streptococcus pneumonia, Bacillus cereus and Staphylococcus aureus. The phytochemical analysis of the extract showed presence of tannin, phenol, flavonoid and terpenoid in all extract, while steroid and saponin were absent in some. The agar diffusion method was employed for the assessment of the sensitivity of the extracts. The ethyl acetate and aqueous fractions from the stem bark acetone extract generally showed better antimicrobial activity compared with other extracts from leaves. The extract was active both against gram positive bacteria (Bacillus cereus and Streptococcus pneumonia) and gram negative bacteria (Escherichia coli, Pseudomonas aeruginosa, , Bacillus cereus and Staphylococcus aureus) at varying zone of inhibition. The results of the study showed the potential of identifying novel antibacterial agent from P. guajava bark and leaves while optimising the potential application for treatment in traditional medicine.

The most recent and non-invasive approach for studying early-stage biomarkers is liquid biopsy. It implies the extraction and analysis of non-solid biological tissues (serum, plasma, saliva, urine and cerebrospinal fluid) without undergoing invasive procedures to determine disease prognosis. Liquid biopsy can be used for the screening of several components such as extracellular vesicles, microRNAs, cell-free DNA, cell-free mitochondrial and nuclear DNA, circulating tumor cells, circulating tumor DNA, transfer RNA and circular DNA or RNA derived from body fluids. Its application includes early disease diagnosis, surveillance of disease activity, and treatment response monitoring, with growing evidence for validating this methodology in cancer, liver disease, and central nervous system (CNS) disorders. This review will provide an overview of mentioned liquid biopsy components, which could serve as valuable biomarkers for the evaluation of complex neurological conditions, including Alzheimer’s disease, Parkinson's disease, amyotrophic lateral sclerosis, multiple sclerosis, epilepsy, stroke, traumatic brain injury, CNS tumors, and neuroinfectious diseases. Furthermore, this review highlights the future directions and potential limitations associated with liquid biopsy.

Renal cell carcinoma (RCC) is the second most common cancer of the urinary system. The current therapeutic strategies are based on partial or total nephrectomy and/or targeted therapies based on immune checkpoint inhibitors to which patients are often refractory. Preventive and screening strategies are not existing and the few available biomarkers for RCC are characterized by the lack of sensitivity, outlining the need of novel noninvasive and sensitive biomarkers for an early diag-nosis and a better disease monitoring. Blood liquid biopsy (LB) is a non- or minimally invasive procedure for a more representative view of tumor heterogeneity than the tissue biopsy, poten-tially allowing real-time monitoring of cancer evolution. Growing interest is focused on the extra-cellular vesicles (EVs) secreted by either healthy or tumoral cells and recovered in a variety of bio-logical matrices, blood included. EVs are involved in cell-to-cell crosstalk transferring their mRNAs, miRNAs, and proteins content. In particular, transferred miRNAs may regulate the tu-morigenesis and proliferation also impacting on resistance to apoptosis, thus representing poten-tial useful biomarkers. Here we present the latest efforts in the identification of circulating miR-NAs in blood samples, focusing on the potential use of EV derived miRNAs as RCC diagnostic, prognostic markers.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Tissue programmed death ligand-1 (PD-L1) protein is the recognized predictive immune biomarker of immune checkpoint inhibitor (ICI) treatment benefit in metastatic non-small cell lung cancer (NSCLC). However, tissue PD-L1 protein testing can be limited by tumor heterogeneity and fraught with tissue acquisition difficulties. A plasma PD-L1 assay potentially overcomes these tissue limitations. Patients with metastatic NSCLC treated with first-line ICI-based treatment and available results of plasma cfRNA PD-L1 by real-time polymerase chain reaction (RT-PCR) and tissue PD-L1 protein PD-L1 with the Dako 22C3 monoclonal antibody were retrospectively assessed for median and landmark 3-year overall survival (OS). OS was identical whether positive plasma cfRNA PD-L1 expression or positive tissue PD-L1 protein expression (median OS 15 months; 3-year landmark OS 30%; hazard ratio (HR) 0.97; 95% CI, 0.44-2.10). Positive plasma cfRNA PD-L1 patients also demonstrated a numerically longer median and higher 3-year OS compared to patients lacking PD-L1 expression (median 15 months versus 8 months; 3-year landmark OS 30% versus 15%; HR 0.56; 95% CI, 0.27-1.17). Plasma cfRNA PD-L1 expression by RT-PCR was similarly predictive of ICI-based treatment benefit as tissue PD-L1 protein expression.

We continue in this paper to illustrate the implications of the Dual Model of Liquids (DML) by deriving the expression for the isochoric specific heat as function of the collective degrees of freedom available at a given temperature and analyzing its dependence on temperature. Two main tasks will be accomplished. First, we show that the expression obtained for the isochoric specific heat in the DML is in line with the experimental results. Second, the expression will be compared with the analogous one obtained in another theoretical dual model of the liquid state, the Phonon Theory of Liquid Thermodynamics. This comparison will allow to get interesting insights about the number of collective degrees of freedom available in a liquid and on the value of the isobaric thermal expansion coefficient, two quantities that are related to each other in this framework.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

Background: Cell-free DNA (cfDNA) analysis has become a promising tool for diagnosis, prognosis and monitoring of lymphoma cases. Until now, research in this area has mainly focused in aggressive lymphomas with scanty information from other lymphoma subtypes. Methods: We selected 256 patients diagnosed with lymphomas including a large variety of B-cell and T-cell non-Hodgkin and Hodgkin lymphomas and quantified cfDNA from plasma at the time of diagnosis. We further selected 49 large B cell lymphomas (LBCL) and analyzed cfDNA levels at diagnosis (pre-therapy) and after therapy. In addition, we performed NGS in cfDNA and tissue in this cohort of LBCL. Results: Lymphoma patients showed a statistically significant higher cfDNA concentration than healthy controls (mean 53.0 ng/mL vs 5.6 ng/mL, p <0.001). The cfDNA concentration correlated with lymphoma subtype, lactate dehydrogenase, International Prognostic Index (IPI) score, Ann Arbor (AA) and B-symptoms. In 49 LBCL cases, the cfDNA concentration decreased after therapy in cases who achieved complete response (CR), and increased in non-responders. The median cfDNA at diagnosis of patients who achieved CR and later relapsed was higher (81.5 ng/mL) compared with levels of those who did not (38.6 ng/mL). A concordance of 84% was observed between NGS results in tumor and cfDNA samples. Higher VAF in cfDNA correlated with advanced stage and bulky disease. Conclusions: cfDNA analysis can be easily performed in almost all lymphoma cases. The cfDNA concentration correlated with the characteristics of aggressiveness of the lymphomas and in LBCL with the response achieved after therapy. These results support the utility of cfDNA analysis as a complementary tool in the management of lymphoma patients.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

Ionic liquid MIE-NH2 displays a new role of development of modification of glycoproteins of lactoferrin through a reductive amination mechanism to synthesize versatile pharmaceuticals. This work introduces a new strategy of modification of Lactoferrin by using methylimidazolium N-ethylamine, this ionic liquid MIE-NH2 linked to N-glycans in Lactoferrin derivatives. Using UPLC/ESI-QTOF and MALDI-TOF mass spectrometry to perform and detect the modifying of ionic liquid-linked glycoproteins. Relevantly, modifying the lactoferrin by MIE-H2 as a small molecule of ion liquid lactoferrin (IL-Lf), which could be a potential antiviral drug and it is achieved by inhibiting various targets. The probability of the lactoferrin modified as a small IL-Lf-molecule to inhibit any of these targets was investigated to find out its potency as a SARS-CoV-2 inhibitor. Molecular docking disclosed the activity of modifying glycoproteins - small IL-Lf-molecules containing amino groups and interaction with targeted Mpro, RdRp, TMPRSS2, and PLpro. Clinically, this study shows the a volubility to provide small IL-Lf-molecules as significantly important drugs that target main protease (Mpro), RNA dependent RNA polymerase (RdRp), transmembrane protease serine 2 (TMPRSS2), and Papain-like protease (PLpro).

Previous research via cell experiments has shown that ultrafine particles (UFPs, particles less than 100 nm) emitted from Three-Dimensional desktop printers (3D printers) had cytotoxicity. However, a few particles from different filaments and their cytotoxicity combinations have been tested. Here we quantify emissions of UFPs and use Air-Liquid Interface (ALI) from one commercially available filament extrusion desktop 3D printer utilizing three different filaments by controlled experiments. A549 cells were exposed at the ALI to UFPs generated by a working 3D printer for an average of 45 minutes and 90 minutes. Twenty-four hours after exposure, cells were analyzed for percent cytotoxicity grown on the 24-well ALI insert (LDH assay). UFP exposure resulted in decreased cell viability (significantly increased LDH levels). The result shows that Acrylonitrile butadiene styrene (ABS) has the most significant particle emission. ALI exposures enable in vitro testing of mixtures of particles such as UFP from a 3D printer. ABS is the only filament with a significant difference compared with the HEPA control in 90 minutes of exposure (p-value &lt;0.05). ABS and PETG we used during the experiment presented a significant difference compared with the HEPA control in 45 minutes of exposure.A screening analysis of potential exposure to these products in a typical environment suggests caution should be used when operating many printer and filament combinations in poorly ventilated spaces or without the aid of combined gas and particle filtration systems.