This paper addresses the modeling of the iron ore direct reduction process, a process likely to reduce CO₂ emissions from the steel industry. The shaft furnace is divided into three sections (reduction, transition, and cooling), and the model is two-dimensional (cylindrical geometry for the upper sections and conical geometry for the lower one), to correctly describe the lateral gas feed and cooling gas outlet. This model relies on a detailed description of the main physical–chemical and thermal phenomena, using a multi-scale approach. The moving bed is assumed to be comprised of pellets of grains and crystallites. We also take into account eight heterogeneous and two homogeneous chemical reactions. The local mass, energy, and momentum balances are numerically solved, using the finite volume method. This model was successfully validated by simulating the shaft furnaces of two direct reduction plants of different capacities. The calculated results reveal the detailed interior behavior of the shaft furnace operation. Eight different zones can be distinguished, according to their predominant thermal and reaction characteristics. An important finding is the presence of a central zone of lesser temperature and conversion.

This research paper is to analyze the planning and design techniques of the tourism complexes in the process of municipalities’ master planning. First, it explains the importance of the tourism industry with the help of theories of scholars and experts. Then, it emphasizes the link between the economic developments of cities/regions with the development of the tourism industry. The innovation of this work is to integrate tourism industry planning and comprehensive regional/ urban planning. The main way of doing this is to plan and design the tourism complexes in the early stages of the master planning of the municipality. Urban land-use policies and locating techniques are suggested through this research. Land-use policies and new urban design models for the regional/urban sustainable development are some of the other handouts in this paper. The outcome of this research is good assistance for engineers, planners, and students of urban and regional development.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

In this paper the influence of austempering temperature and salt bath agitation on the final microstructure and mechanical properties of the ferritic ductile iron were studied. 17 samples had been subjected to different heat treatment parameters. Different microstructures were recorded upon the completion of the tests. From the obtained micro images, it is obvious that both the austempering temperature and salt bath agitation affect the final microstructure of the austempered ductile iron. Lower austempering temperatures and salt bath agitation produce more ausferrite in the microstructure, hence the harder and tougher phases are present. This was confirmed with hardness and toughness test of the 17 heat-treated samples. Lower austempering temperatures give more ausferrite phase and therefore higher hardness, but hardness decreases with increasing austempering temperatures. Toughness rises with rising austempering temperatures, but drops significantly with temperatures above 395°C because of the final microstructure.

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Abstract: The aim of this study was to find out the incidence of anemia in pregnant women of Swat District; to analyze the iron variations and its dietary effects.Data were collected during the periods of January – September 2016. The study of samples comprised of 250 pregnant women in the different trimester. Blood sample from each woman was collected and full blood count (FBC) was conducted through Mindray BC-3000 plus hem analyzer for all pregnant individuals. Confirmed anemic cases were then examined for IDA with serum ferritin, serum iron, total iron binding capacity (TIBC) through Randox kit and serum transferrin saturation was estimated by formula (serum ferritin saturation =serum iron ×100/TIBC). The total number of participants in the first trimester were 50, among them 26 women were suffer from iron deficiency anemia (IDA) with 52% weightage of prevalence rate, (mean Hb concentration 9.602 ± 0.87 g/dl). The rates of IDA were 63.3%; ( mean Hb concentration 8.48 ± 1.24 g/dl) and 54%; ( mean Hb concentration 9.18 ± 1.28 g/dl), among 150 and 50 participants in the second and third trimester, respectively. A significant correlation was found between serum ferritin and Hb, serum ferritin against MCV and serum ferritin against MCH. The high prevalence of anemia was found 78.2% in the age group from 26-30 followed by 78.2% in the age group 36-40 years compared to those of other age groups in the second trimester. In this study the prevalence of IDA in third trimester is lower compared to first and second trimester.

There is a marked momentum towards the use of clean hydrogen energy as an alternative for fossil fuels. Renewable energies such as solar and wind are being used to generate hydrogen from the water hydrolysis process. Indeed, this approach stores renewable energies in the form of combustible hydrogen for other energy uses. The other alternative that could be economically more cost-effective at the current technology stage is to explore the natural “Hydrogen System” where the natural hydrogen is generated and accumulated within the earth system, the same that stands for a “Petroleum System”. The Discovery of a large accumulation of relatively pure natural hydrogen (H2) in Mali has triggered the opportunity of searching for natural hydrogen accumulations in other countries. The generation of hydrogen from a circular depression in Mali and some other countries is linked to the presence of geologically very old iron-rich basement rocks. Solid-liquid redox reactions between iron-rich minerals and groundwater that split water are a possible source of H2 in deep basement rocks. It is believed that the hydrogen degassing may be detected by surface topographic circular to sub-circular shallow depressions. Chemical processes such as dissolution by hydrogen are considered to play the main role in the formation of the circular depressions through preferential vertical hydrogen migration channel. Archean iron-rich Yilgarn Craton that covers a vast area of Western Australia (WA) contains abundant iron-rich mafic-ultramafic rocks. The craton reveals many surficial circular depressions visible through satellite images. The area has abundant fault systems and is blanketed with Eocene sedimentary rocks containing high-quality reservoir rocks. All these characteristics seem to provide most of the required elements, such as hydrogen source, migration pathway, and reservoir rock for a “Hydrogen System” in this area.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Metallic elements of higher economic value occurring in the mineralogy of Zimapán are Pb, Zn, Cu and Fe, said elements are sold as concentrates, which, even after processing, generally include significant concentrations of Mo, Cd, Sb, Ag and As that could recover through different leaching methods. In this work the influence of temperature was studied in the complexation of silver in the S₂O₃^2--O₂ system. Chemical and mineralogical characterization of concentrated Zn from the state of Hidalgo confirmed the presence of the silver contained in a sulfide of silver arsenic (AgAsS₂) through the techniques of Atomic Absorption Spectrophotometry (AAS), X-Ray Diffraction (XRD) and Scanning Electron Microscopy-Energy-Dispersive X-Ray Spectroscopy (SEM-EDS). The mineralogical species identified allowed the construction mineralogical species Pourbaix diagrams in the range of 298 K to 333 K, through which the Eh-pH conditions to obtain silver in solution were determined. The formation of Ag(S₂O₃)₂^3- complex was confirmed by characterizing liquors leached using the technique Infrared Spectroscopy Fourier Transform (FTIR).

Aquatic animals have unique physiological mechanisms to absorb and retain minerals from their diets and water. Research and development in the area of mineral nutrition of farmed fish and crustaceans have been relatively slow and major gaps exist in the knowledge of trace element requirements, physiological functions and bioavailability from feed ingredients. Quantitative dietary requirements have been reported for three macroelements (calcium, phosphorus and magnesium) and six trace minerals (zinc, iron, copper, manganese, iodine and selenium) for selected fish species. Mineral deficiency signs in fish include reduced bone mineralization, anorexia, lens cataracts (zinc), skeletal deformities (phosphorus, magnesium, zinc), fin erosion (copper, zinc), nephrocalcinosis (magnesium deficiency, selenium toxicity), thyroid hyperplasia (iodine), muscular dystrophy (selenium) and hypochromic microcytic anaemia (iron). An excessive intake of minerals from either diet or gill uptake causes toxicity and therefore a fine balance between mineral deficiency and toxicity is vital for aquatic organisms to maintain their homeostasis either through increased absorption or excretion. Release of minerals from uneaten or undigested feed and from urinary excretion can cause eutrophication of natural waters, which requires additional consideration in feed formulation. The current knowledge in mineral nutrition of fish is briefly reviewed.

Comminution is a very important and result-determining step in mineral processing. This is because further downstream processes in the beneficiation chain depend entirely on it. Comminution includes the blasting, crushing, and grinding of ore to liberate valuable mineral particles. It consumes most of the energy used in mineral processing plants with grinding using up to 50% of the provided energy. Tumbling mills are an old technology that is still commonly used for grinding. One of the most used tumbling mills is the ball mill. This paper reviews different types of grinding media that have been developed and improved over the years and their properties. Also reviewed are the effects of grinding media on various aspects such as energy consumption, mill efficiency, minerals liberation and grinding rate. A comparison of the grinding media is given together with the knowledge gaps that still need to be bridged to improve the quality and performance of grinding media used in ball mills. Despite various research conducted on ball mills, the grinding process is still a very energy inefficient process. This creates a great opportunity for further research to improve the process because just a slight improvement in the process efficiency significantly reduces the production costs and provides a lot of environmental benefits.

Primate vision is an active process that constructs a stable internal representation of the 3D world based on 2D sensory inputs that are inherently unstable due to incessant eye movements. We present here a mathematical framework for processing visual information for a biologically-mediated active vision stereo system with asymmetric conformal cameras. This model utilizes the geometric analysis on the Riemann sphere developed in the group-theoretic framework of the conformal camera, thus far only applicable in modeling monocular vision. The asymmetric conformal camera model constructed here includes the fovea’s asymmetric displacement on the retina and the eye’s natural crystalline lens tilt and decentration, as observed in ophthalmological diagnostics. We extend the group-theoretic framework underlying the conformal camera to the stereo system with asymmetric conformal cameras. Our numerical simulation shows that the 1 theoretical horopter curves in this stereo system are conics that well approximate the empirical longitudinal horopters of the primate vision system.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

During flux weakening operation time (FWOT), the total iron loss rises and affects the accuracy of loss prediction and efficiency especially if a large range of FWOT exists. Iron loss prediction is widely employed in investigations for a fast electrical machine analysis using 2-D FEA. This paper studies harmonic loss analytically by a steady-state equivalent circuit. Consideration of skin effects and iron saturation are utilized in order to examine the accuracy through the relative error distribution in the frequency domain of each model from 50 to 700 Hz. Additionally, this comparative study presents a torque-frequency-flux density calculation over each single term of the modified IEM-formula. The analytical calculation is performed using 2-D FEA for a classic and modified IEM-formula along with experimental verifications on a surface-mounted PMSG for a wind generation application.

Saccharomyces cerevisiae cells are killed by zymocin, a tRNase ribotoxin complex from Kluyveromyces lactis, which cleaves anticodons and inhibits protein synthesis. Zymocin’s action requires specific chemical modification of uridine bases in the anticodon wobble position (U34) by the Elongator complex (Elp1-Elp6). Hence, loss of anticodon modification in mutants lacking Elongator or related KTI (K. lactis Toxin Insensitive) genes protects against tRNA cleavage and confers resistance to the toxin. Here, we show that zymocin can be used as a tool to genetically analyse KTI12, a gene previously shown to code for an Elongator partner protein. From a kti12 mutant pool of zymocin survivors, we identify motifs in Kti12 that are functionally directly coupled to Elongator activity. In addition, shared requirement of U34 modifications for nonsense and missense tRNA suppression (SUP4; SOE1) strongly suggests that Kti12 and Elongator cooperate to assure proper tRNA functioning. We show that the Kti12 motifs are conserved in plant ortholog DRL1/ELO4 from Arabidopsis thaliana and seem to be involved in binding of cofactors (e.g. nucleotides, calmodulin). Elongator interaction defects triggered by mutations in these motifs correlate with phenotypes typical for loss of U34 modification. Thus, tRNA modification by Elongator appears to require physical contact with Kti12, and our preliminary data suggest that metabolic signals may affect proper communication between them.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

This paper aims at addressing the exploitation of solid-state carriers for hydrogen storage, with attention paid both to the technical aspects, through a wide review of the available integrated systems, and to the social aspects, through a preliminary overview of the connected impacts from a gender perspective. As for the technical perspective, carriers to be used for solid-state hydrogen storage for various applications can be classified into two classes: metal and complex hydrides. Related crystal structures and corresponding hydrogen sorption properties are reviewed and discussed. Fundamentals of thermodynamics of hydrogen sorption evidences the key role of the enthalpy of reaction, which determines the operating conditions (i.e. temperatures and pressures). In addition, it rules the heat to be removed from the tank during hydrogen absorption and to be delivered to the tank during hydrogen desorption. Suitable values for the enthalpy of hydrogen sorption reaction for operating conditions close to ambient (i.e. room temperature and 1-10 bar of hydrogen) are close to 30 kJ·molH2 1. The kinetics of hydrogen sorption reaction is strongly related to the microstructure and to the morphology (i.e. loose powder or pellets) of the carriers. Usually, kinetics of hydrogen sorption reaction is rather fast, and the thermal management of the tank is the rate determining step of the processes. As for the social perspective, various scenarios for the applications in different socio-economic contexts of solid-state hydrogen storage technologies are described. As it occurs with the exploitation of other renewables innovative technologies, a wide consideration of the social factors connected to these processes is needed to assess the extent to which a specific innovation might produce positive or negative impacts in the recipient socio-economic system and to explore the potential role of the social components and dynamics in fostering the diffusion of the innovation itself. Attention has been addressed to the gender perspective, in view of the enhancement of hydrogen-related energy storage systems, intended both in terms of the role of women in triggering the exploitation of hydrogen-based storage as well as to the impact of this innovation in their current conditions, at work and in daily life.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

Thalassemia is genetic blood disease cause by absence or decrease of one or more of the globin chain synthesis. Beta thalassemia is characterized by one or more mutations in beta globin gene. Absence or reduced amount the of beta globin chains cause ineffective erythropoiesis which leads to anemia. Beta thalassemia has been further divided into three main forms: Thalassemia minor/silent carrier, major and intermedia. More severe form is thalassemia major in which patients depend upon blood transfusion for survival and high level of iron occur as a consequence of consistent blood transfusion. Over loaded iron invokes the synthesis of reactive oxygen species that are toxic in redundancy and triggering the impairment to vascular, endocrine and hepatic system. Thalassemia can be diagnosed and detected through various laboratory tests such as blood smear, prenatal testing (genetic testing of amniotic fluid), DNA analysis (genetic testing) and complete blood count. Treatment of thalassemia intermedia is symptomatic but it can also be managed by splenectomy and folic supplementation. While thalassemia major can be treated by transplantation of bone marrow, regular transfusion of blood and iron chelation treatment, stimulation of fetal hemoglobin production, hematopoietic stem cell transplantation and gene therapy.

Two types of heterometallic (Fe(III),Na) silsesquioxanes [Ph₅Si₅O₁₀]₂[Ph₁₀Si₁₀O₂₁]Fe₆(O^2‒)₂Na₇(H₃O⁺)(MeOH)₂(MeCN)_4.5.1.25(MeCN), I, and [Ph₅Si₅O₁₀]₂[Ph₄Si₄O₈]₂Fe₆Na₆(O^2‒)₃(MeCN)_8.5(H₂O)_8.44, II, were obtained and characterized. X-Ray studies established distinctive structures of both products, with pair of Fe(III)-O-based triangles surrounded by siloxanolate ligands, giving fascinating cage architectures. Complex II proved to be catalytically active in the formation of amides from alcohols and amines, thus becoming a rare example of metallasilsesquioxanes performing homogeneous catalysis. Benzene, cyclohexane and other alkanes, as well as alcohols, can be oxidized in acetonitrile solution to phenol, the corresponding alkyl hydroperoxides and ketones, respectively, by hydrogen peroxide in air in the presence of catalytic amounts of complex II and trifluoroacetic acid. Thus, the cyclohexane oxidation at 20 °C gave oxygenates in very high for alkanes yield (48% based on alkane). The kinetic behaviour of the system indicates that the mechanism includes the formation of hydroxyl radicals generated from hydrogen peroxide in its interaction with diiron species. The latter are formed via monomerization of starting hexairon complex with further dimerization of the monomers.

Nickel nitrate diammine, Ni(NH₃)₂(NO₃)₂, can be synthesised from the thermal decomposition of the nickel nitrate hexammine, Ni[(NH₃)₆](NO₃)₂. The hexammine decomposes in 2 distinct steps; the first releases 4 equivalents of ammonia while the second involves the release of NO_x, N₂ and H₂O to yield NiO. The intermediate diammine compound can be isolated following the first deammoniation step or synthesised as a single phase from the hexammine under vacuum. Powder X-ray diffraction (PXD) experiments have allowed the structure of Ni(NH₃)₂(NO₃)₂ to be solved for the first time. The compound crystallises in orthorhombic space group Pca2₁ (a = 11.0628 (5) Å, b = 6.0454 (3) Å, c = 9.3526 (4) Å; Z = 4) and contains 11 non-hydrogen atoms in the asymmetric unit. Fourier Transform Infrared (FTIR) spectroscopy demonstrates that the bonding in the ammine is consistent with the structure determined by PXD.

In the paper, the authors survey integral representations (including the Lévy--Khintchine representations) and applications of some bivariate means (including the logarithmic mean, the identric mean, Stolarsky's mean, the harmonic mean, the (weighted) geometric means and their reciprocals, and the Toader--Qi mean) and the multivariate (weighted) geometric means and their reciprocals, derive integral representations of bivariate complex geometric mean and its reciprocal, and apply these newly-derived integral representations to establish integral representations of Heronian mean of power 2 and its reciprocal.

Current theories of autoimmunity are diverse, sometimes contradictory, and suffer from incompleteness. Although substantial evidence exists that adaptive and innate immunity, sex, genetic predisposition, and the microbiome all play essential roles in autoimmune disease etiologies and pathogenesis, and that antigen processing is altered during disease induction, no existing theory integrates all of these factors through a single, coherent mechanism. In an attempt to focus the field on the need to elucidate such an integrative mechanism, I propose one possibility here that, if nothing else, helps to identify the nature of the problems that need to be addressed. My theory is that autoimmune diseases are induced by normal immunological responses to unique pairs of complementary antigens, at least one of which is a molecular mimic of a host target. Each antigen in the complementary pair induces a complementary immune response (T or B cell); although each immune response is idiotypic in origin, the antigenic complementarity results in what appears to be an idiotype-anti-idiotype relationship between the responses. Additionally, because of the antigenic complementarity, each immune response mimics one of antigens, abrogating the distinction between self and non-self. If at least one of the antigens mimics a host antigen, then the resulting immunological civil war spreads to a host tissue. Complementary antigens also alter antigen processing so that antigens that would normally be proteolytically digested are presented by the major histocompatibility complex (MHC) to T and B cell receptors inducing a cross-reactive immune response. The resulting civil war is supported by the innate immune system due to the complementarity of the initiating antigens.. Complementary antigens stimulate synergistic toll-like receptors (TLR) and/or nucleotide-binding oligomerization receptors (NOD) resulting in up-regulation of cytokine production and further stimulation of the adaptive immune response. Because the immune responses (e.g., antibodies) mimic the initiating antigens, this synergistic activation of innate immunity becomes chronic. Additionally, TLR and NOD function are highly sensitive to sex hormones, some becoming up-regulated and some down-regulated in the presence of either testosterone or estrogens. This sensitivity explains how sex modifies susceptibility to autoimmune diseases. Genetic mutations in TLR, NOD and MHC further alter antigen presentation and the degree to which antigens stimulate an immune response explaining how genetics also modifies susceptibility. Finally, sex hormones also alter the host microbiome, which in turn modulates autoimmune disease risk by shaping the immunological nature of self and by mediating susceptibility to microbial infection. Moreover, it appears that the microbiome camouflages itself from the immune system by mimicking the host antigenic repertoire; the mimicry between the antigens of the microbiome and the host results in selective attacks on microbiome constituents concomitant with any autoimmune attack on host tissues. This antigenic complementarity theory thereby integrates all major elements known to affect, or be affected by, autoimmune diseases and provides a set of testable implications.

Maghemite (γ-Fe2O3) is a mineral formed from magnetite oxidation at low temperatures, an intermediate metastable term of the magnetite to hematite oxidation and could be mixed with both. It has magnetic susceptibility similar to magnetite, crystal structure close to magnetite with which it forms a solid solution, while compositionally it equals hematite. Maghemite is thus easily misidentified as magnetite by X-ray diffraction and/or as hematite by spot chemical analysis in iron ore characterization routines. Nonstoichiometric magnetite could be quantified in samples of Brazilian soils and iron ores by the Rietveld method using a constrained refinement of the X-ray patterns. The results were confirmed by reflected light microscopy and Raman spectroscopy, thus qualitatively validating the method. X-ray diffraction with the refinement of the isomorphic substitution of Fe2+ by Fe3+ along the magnetite-maghemite solid solution could help to suitably characterize maghemite in iron ores, allowing for the evaluation of its ultimate influence on mineral processing, by affecting its surface and breakage properties.

Pearl millet is an important food crop in the arid and semi-arid tropical regions of Africa and Asia. These regions are home to millions of poor smallholder’s households living in harsh agro ecology and reported higher prevalence of malnutrition. Such poor households have few options in terms of food crops, besides the limited markets. Indeed, pearl millet is one of the food crops they continue to grow for their food and nutritional security. Pearl millet is important sources of dietary carbohydrates, energy, protein, and important minerals such as calcium, iron and zinc. Considering inherent high nutritional values and climate resilient nature (drought and heat), demand for pearl millet as food, beside valued for its Stover as a source of livestock fodder, is projected to grow strongly in Asia (India) and Africa (West and Central Africa). Iron (cause anemia) and zinc (cause stunting) deficiencies are widespread and serious public health problems worldwide, including India and Africa. Biofortification is a cost-effective and sustainable agricultural strategy to address this problem. Research on pearl millet has shown that large genetic variability (30-140 mg/kg Fe and 20-90 mg/kg Zn) available in this crop can be effectively utilized to develop high-yielding cultivars with high iron and zinc densities. Both Open –pollinated varieties (Dhanshakti and Chakti) and hybrids (ICMH 1202, ICMH 1203 and ICMH 1301) of pearl millet with high grain yield (>3.5 tons/ha in hybrids) and high levels of iron (70-75 mg/kg) and zinc (35-40 mg/kg) densities have been developed and released. Currently, India growing >70,000 ha of biofortified pearl millet, besides more pipeline hybrids and varieties are under various stage of testing at the national (India) and international (west Africa) trials for possible release. Genomic tools will be an integral part of breeding program particularly for nutritional traits to use diagnostic markers and genomic selection. Clinical studies showed that 200g grains from biofortified cultivar would provide bioavailable Fe to meet full recommended daily allowance (RDA) in children, adult men and 80% of the RDA in women. Till today, no markets to promote biofortified cultivars/grains/products as no incentive price and such products aims to address food and nutritional security challenges simultaneously. The demand is likely to increase only after investment and integration into modern public distribution system, nutritional intervention schemes, private seed and food companies with strong mainstreaming nutritional policies. In the non-traditional regions, this will contribute to livestock and poultry feed industry as spill-over benefits to improve nutrition.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

This paper establishes methods that quantify the structure of statistical interactions within a given data set using the characterization of information theory in cohomology by finite methods, and provides their expression in terms of statistical physic and machine learning. Following [1–3], we show directly that k multivariate mutual-informations (I_k) are k-coboundaries. The k-cocycles are given by I_k = 0, which generalize statistical independence to arbitrary dimension k. The topological approach allows to investigate Shannon’s information in the multivariate case without the assumptions of independent identically distributed variables. We develop the computationally tractable subcase of simplicial information cohomology represented by entropy H_k and information I_k landscapes. The I₁ component defines a self-internal energy functional U_k, and (−1)^k I_k,k≥2 components define the contribution to a free energy functional G_k of the k-body interactions. The set of information paths in simplicial structures is in bijection with the symmetric group and random processes, provides a topological expression of the 2nd law and points toward a discrete Noether theorem (1st law). The local minima of free-energy, related to conditional information negativity and the non-Shannonian cone of Yeung [4], characterize a minimum free energy complex. This complex formalizes the minimum free-energy principle in topology, provides a definition of a complex system, and characterizes a multiplicity of local minima that quantifies the diversity observed in biology. Finite data size effects and estimation bias severely constrain the effective computation of the information topology on data, and we provide simple statistical tests for the undersampling bias and for the k-dependences following [5]. We give an example of application of these methods to genetic expression and cell-type classification. The maximal positive I_k identifies the variables that co-vary the most in the population, whereas the minimal negative I_k identifies clusters and the variables that differentiate-segregate the most. The methods unravel biologically relevant I₁₀ with a sample size of 41. It establishes generic methods to quantify the epigenetic information storage and a unified epigenetic unsupervised learning formalism.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

In the context of the development of bioprocesses for the production of biofuels and bulk chemicals, microbial cells are rationally engineered to produce such molecules at high yield and titres in order to develop new biological methods that satisfy economic constraints. The redox and energetic balances of such strains play crucial roles in performance. Processes performed in strict anaerobes have a limited amount of energy available compared to that in aerobic organisms. This energy is obtained through fermentation and/or ion gradient-driven phosphorylation. Such anaerobic organisms have developed energy conservation mechanisms to increase ATP yields. This paper presents the properties of one of these mechanisms catalysed by the Rnf complex, an ion-translocating membrane complex with a ferredoxin NAD+ oxidoreductase activity. The Rnf complex performs the transfer of electrons from reduced ferredoxin to NAD+ coupled with an ion-motive transport. Ferredoxin is a common electron carrier for anaerobic bacteria and, with NAD+, is involved in several pathways of interest for the production of biofuels. This complex was first identified in Rhodobacter capsulatus and found to be involved in nitrogen fixation. It was then found to be involved in energy conservation in multiple anaerobic organisms, from acetobacteria such as Acetobacterium woodii to sulfate-reducing bacteria such as Desulfovibrio alaskensis and autotrophic bacteria such as Clostridium ljungdahlii and Clostridium aceticum. The Rnf complex triggers two types of ion transports: it can be either a sodium or a proton transporter. Both of these transports create a gradient of ions, generating a membrane potential that is then used by ATPase to produce ATP and thus serving as an energy conservation mechanism. In this review, the available information on the Rnf complex from genetic organization up to its in vivo and in vitro activities in several microorganisms is summarized, with a special focus on the proton-motive Rnf complex.

In this article, a generalization of the geometry of Grassmannian chain complex of free abelian groups generated by the projective configuration of points and Cathelineau's infinitesimal complex of polylogarithmic groups is proposed. Firstly, homomorphisms for weight n =2 up to weight n=6 will be introduced to connect sub-complexes of Grassmannian and Cathelineau. Lately, generalization of these morphisms will be shown for weight n=N. The associated diagrams will also be proven to be commutative and bi-complex.

A gold(I) complex with a triphenylphosphine and a monodentate N,N-dimethyldithiocarbamate ligand was synthesized and characterized by Raman spectroscopy and single crystal X-ray diffraction. DFT calculations (Gaussian 09, PBE1PBE/Lanl2dz) were undertaken for a single complex in the gas-phase. The DFT-optimized structure is in good agreement with the crystal structure and the DFT-calculated Raman spectrum also is in excellent agreement with the experimental spectrum. Assignments of the Raman peaks are based on these DFT calculations. Frontier molecular orbitals were calculated and their nature is discussed.

Evolutionary convergence provides natural opportunities to investigate how, when, and why novel traits evolve. Many convergent traits are complex, highlighting the importance of explicitly considering convergence at different levels of biological organization, or ‘multi‐level convergent evolution’. To investigate multi‐level convergent evolution, we propose a holistic and hierarchical framework that emphasizes breaking down traits into several functional modules. We begin by identifying long‐standing questions on the origins of complexity and the diverse evolutionary processes underlying phenotypic convergence to discuss how they can be addressed by examining convergent systems. We argue that bioluminescence, a complex trait that evolved dozens of times through either novel mechanisms or conserved toolkits, is particularly well suited for these studies. We present an updated estimate of at least 94 independent origins of bioluminescence across the tree of life, which we calculated by reviewing and summarizing all estimates of independent origins. Then, we use our framework to review the biology, chemistry, and evolution of bioluminescence, and for each biological level identify questions that arise from our systematic review. We focus on luminous organisms that use the shared luciferin substrates coelenterazine or vargulin to produce light because these organisms convergently evolved bioluminescent proteins that use the same luciferins to produce bioluminescence. Evolutionary convergence does not necessarily extend across biological levels, as exemplified by cases of conservation and disparity in biological functions, organs, cells, and molecules associated with bioluminescence systems. Investigating differences across bioluminescent organisms will address fundamental questions on predictability and contingency in convergent evolution. Lastly, we highlight unexplored areas of bioluminescence research and advances in sequencing and chemical techniques useful for developing bioluminescence as a model system for studying multi‐level convergent evolution.

New antibacterial agents are needed to overcome the increasing number of infectious diseases caused by pathogenic microorganisms due to the emergence of multi-drug resistant strains. In this context, halogens, especially Iodine is known since ages for its antimicrobial activity. Therefore, especially triiodides encapsulated in organometallic complexes can be helpful as new agents against microorganisms. The aims of this work was to study the biological activity of [Na(12-Crown-4)₂]I₃ against gram positive Streptococcus pyogenes, Streptococcus faecalis, the spore forming bacteria Bacillus subtilis and gram negative bacteria Escherichia coli, Proteus mirabilis, Pseudomonas aeruginosa and Klebsiella pneumoniae, as well as the yeast Candida albicans. The antimicrobial and antifungal activities of the triiodide were determined by zone of inhibition plate studies. [Na(12-Crown-4)₂]I₃ exhibited potent antimicrobial activity on gram positive Streptochocci and the yeast C. albicans. Furthermore, the gram negative bacteria P. aeruginosa and K. pneumoniae were less effectively inhibited, while E. coli and P. mirabilis proved to be even resistant.

INTRODUCTION. The most common cause of eating non-food items (pica) is specific deficiencies of minerals, such as iron. This study aimed to assess the relationship between Pica and Iron deficiency anemia among pregnant women. METHODS. The study was conducted in the out-patient department, antenatal Clinic at East Jeddah Hospital from July to September 2020. Design: A quantitative descriptive correlation design. Sample size: A total of 400 pregnant women, included anemic pregnant women, ≥ 18 years old, with singleton fetus and iron deficiency anemia. RESULTS. The mean age was 32.2 ± 6.6, half of the participants reported food cravings. Ice was the main item in pica followed by clay and chalk. Two-thirds had pica, more than half during the 1st trimester. There is a statistically significant relationship between pica and the history of a family member, parity, and gravidity at (P< 0,001, P <0,001, P <0,005) respectively. Hb and hematocrit in relation to pica reflected a statistically significant relationship (P< 0,001) and (P< 0,001), respectively. The symptoms attributed to iron deficiency were significantly associated with pica (P< 0,006). CONCLUSION. The pica and iron deficiency anemia had a significant association with pregnant women in EJH. RECOMMENDATION. The follow-up visits should integrate the food behavior inquiry to check if the pica existing with anemic or non-anemic pregnant women. Also, increase the awareness among midwives-nurses about the prevalence of pica and iron deficiency anemia among pregnant women.

Motivated by a common Mathematical Finance topic, this paper surveys several results concerning windings of 2-dimensional processes, including planar Brownian motion, complex-valued Ornstein-Uhlenbeck processes and planar stable processes. In particular, we present Spitzer's asymptotic Theorem for each case. We also relate this study to the pricing of Asian options.

The cause-effect relationship between iron deficiency anemia (IDA) and osteoporosis has not been established in the general population. Thus, the current longitudinal study determined the role of IDA as a risk factor for osteoporosis by analyzing a large nationwide population-based sample. In a sample of 1,000,000 randomly sampled individuals from the 1998-2012 Taiwan National Health Insurance Research Database, patients with IDA (case group [n=35,751]) and individuals without IDA (control group [n=178,755]) were compared. Patients who were <20 years of age and who had pre-existing osteoporosis prior to the diagnosis of IDA were excluded. Each patient with IDA was age- and gender-matched to 5 individuals without IDA. The diagnoses of IDA and osteoporosis (coded using ICD-9CM) were further confirmed with blood test results and X-ray bone densitometry to ensure the accuracy of the diagnoses. Osteoporosis occurred more often among patients with IDA compared to individuals without IDA (2.27% vs. 1.32%, p<0.001). Cox proportional hazard analysis revealed that the risk for osteoporosis was significantly higher in the case than the control group (hazard ratio [HR]=1.74; 95% CI=1.61-1.88) and remained similar after adjustment for covariates (adjusted HR=1.81; 95% CI=1.67-1.97). Compared with individuals without IDA, the risk for osteoporosis was even higher for patients with IDA who received intravenous ferrum therapy (adjusted HR=2.21; 95% CI=1.85-2.63). In contrast, the risk for osteoporosis was reduced for patients with IDA who received a blood transfusion (adjusted HR=1.47; 95% CI=1.20-1.80). As a predictor, prior IDA is a significant and independent risk factor for development of osteoporosis. In contrast to blood transfusion treatment, the use of intravenous ferrum may further increase the risk for future osteoporosis.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Soil microbial fuel cells (sMFC) are a novel technique that use organic matters in soils as an alternative energy source. External resistance (ER) is a key factor influencing sMFC performance and, furthermore, alters the soil’s biological and chemical reactions. However, little information is available on how the microbial community and soil component changes in sMFC with different ER. Therefore, the effects of anodes of sMFC at different ER (2000 Ω, 1000 Ω, 200 Ω, 80 Ω and 50 Ω) were examined by measuring organic matter (OM) removal efficiency, trace elements in porewater and bacterial community structure in contaminated paddy soil. The results indicated that ER has significant effects on sMFC power production, OM removal efficiency and bacterial beta diversity. Moreover ER influences iron, arsenic and nickel concentration as well in soil porewater. In particular, greater current densities were observed at lower ER (2.4mA, 50Ω) compared to a higher ER (0.3mA, 2000Ω). The removal efficiency of OM increased with decreasing ER whereas it decreased with soil distance away from the anode. Furthermore, principal coordinate analysis (PCoA) revealed that ER may shape the bacterial communities that develop in the anode vicinity but have minimal effect on that of the bulk soil. The current study illustrates that lower ER can be used to selectively enhance the relative abundance of electrogenic bacteria and lead to high OM removal.

The purpose of this study is to investigate the moderating effect of technology configuration capability on the relationship between strategic flexibility and organizational performance through different stages of technological life cycle. Through the empirical research on the 439 Chinese high-tech organizations, it shows that a technological configuration capability has enhanced the effect of strategic flexibility to the organizational performance in the complex dynamic environment. However, the impact on the different stages of technological life cycle is different. In addition, this paper explored strategic flexibility on different stages of technological life cycle on the basis of empirical study.

Systems Engineering is an ubiquitous discipline of Engineering overlapping industrial, chemical, mechanical, manufacturing, control, software, electrical, and civil engineering. It provides tools for dealing with the complexity and dynamics related to the optimisation of physical, natural, and virtual systems management. This paper presents a review of how multi-agent systems and complex networks theory are brought together to address Systems Engineering and management problems. The review also encompasses current and future research directions both for theoretical fundamentals and applications in Industry. This is made by considering trends such as mesoscale, multiscale, and multilayer networks; along with the state-of-art analysis on network dynamics and intelligent networks. Critical and smart infrastructure, manufacturing processes, and supply chain networks are instances of research topics for which this literature review is highly relevant.

Stess in laser cladding coating is an important factor affecting the safe operation of remanufacturing components. Ultrasonic testing has become a hot direction in nondestructive evaluation of stress, because it has the advantages of safety, non-destructive and on-line detection. This paper provides a review of ultrasonic testing for stress in remanufacturing laser cladding coating. It summarizes the recent research outcomes on ultrasonic testing for stress, analyzes mechanism of ultrasonic testing for stress. Remanufacturing laser cladding coating shows typical anisotropic behaviors, the ultrasonic testing signal in laser cladding coating is influenced by many complex factors, such as microstructure, defect, temperature and surface roughness, etc. At present, ultrasonic testing for stress in laser cladding coating can only be done roughly. The paper discusses active mechanism of micro / macro factors to the reliability of stress measurement and the impact of stress measurement to the quality and safety of remanufacturing components. Base on the discussion, the paper proposes strategies for acquisition of nondestructive, rapid and accurate measurement of stress in remanufacturing laser cladding coating.

Magnetic Resonance Imaging (MRI) is a powerful, non-invasive and nondestructive tool, capable of providing three-dimensional (3D) images of living organisms. The use of magnetic contrast agents has allowed clinical researchers and analysts to enormously increase the sensitivity and specificity of MRI since these substances change the intrinsic properties of the tissues within a living body, increasing the information present in the images. The advances in nanotechnology and materials science as well as the research of new magnetic effects have been the driving forces that propel the use of magnetic nanostructures as promising alternatives to the commercial contrast agents used in MRI. This review discusses the principles associated with the use of contrast agents in MRI as well as the most recent reports focused on nanostructured contrast agents. The potential applications of gadolinium (Gd) and manganese Mn-based nanomaterials and iron oxide nanoparticles in this imaging technique are discussed as well, from their magnetic behavior to the mainly used materials and nanoarchitectures. Then, it is also addressed the recent efforts made to develop new types of contrast agents based on synthetic antiferromagnetic and high-aspect ratio nanostructures. Furthermore, the application of these materials in theragnosis, either as contrast agents and controlled drug release, contrast agents and thermal therapy or contrast agents and radiosensitizers, is also presented.

Differential equation models to understand interaction between plant and nutrient solution are presented. The root cells selectively emit H+ ions with active transport consuming ATPs to establish electrical gradient along the cell membrane. It establishes electrical field with Nernst potential to make positively charged ions outside the cell membrane flow into the root cell. Anion influx is also modulated by H+ ion concentration because plant root cell absorbs negatively charged particles with symport. If an anion collides with H+ cell to make net charge as neutral, at symport channel, it can flow through. In this paper, mathematical models for cation and anion absorption are introduced. Cation absorption model was induced from Ohm's law combined with Goldman's equation. Anion absorption model is similar to chemical reaction rate model. Both models have physiological terms influenced by gene expression pattern, species or phenotypes. Cation model also includes terms for ion's kinetic and electrical properties, growth of plant and interaction between the root and the surroundings. Simulation for 20 different sets of coefficients showed that the physiology-related coefficient has important role on nutrition absorption tendencies of plants.

Mexico is an exceptional setting for ethnomycology since human cultures have interacted with fungi for thousands of years; the state of Michoacán is particularly important since nearly 11% of the fungi species recorded in Mexico occur there, 139 species being edible. This study aimed to analyze the taxonomic diversity and use forms of fungi, their position in worldview of people, and the management forms practiced on edible fungi in the Purépecha communities of Cherán and Pichátaro and the environmental problems in relationship with fungi management. We conducted semi-structured interviews during visits to regional markets, participant observations in harvesting areas, workshops, and presentation of results to the communities and communal authorities. We recorded ethnoecological information for 21 edible fungi species. The words jongo and terekua correspond to useful fungi in Purépecha, while jeramba refers to not edible fungi. In Cherán people identify different vegetation types where mushrooms occur; they recognize the “pinadas forest” dominated by Pinus leiophylla, “encineras” (dominated by Quercus crassipes), “tepamu forest” (dominated by Alnus acuminata), “sharhari forest” (Quercus aff. laeta), and grasslands, all of them sites where mushrooms grow. Fungi handlers identified environmental problems like land use changes, illegal extraction of forest resources, deforestation, unplanned urban growth, uncontrolled fires, livestock raising, and agricultural intensification, which affect fungi communities. In turn, these factors have secondary consequences like soil erosion, reduction of native vegetation and reduction of rainwater retention that directly disturb diversity, distribution, and abundance of fungi. Information from this study and workshops conducted with the community helped to design strategies for conservation of both forests and fungi.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

The issue of workplace toxicity constitutes a major problem for employers, employees and society at large. Toxicity in a workplace context relates to damaging behaviours perpetrated by individuals and organisations that netatively impact on the health and wellbeing of others. Workplace toxicty is habitually associated with activities such as bullying, harrassment, unethical and even illegal acts. In this article, today’s workplace is likenened to a cage where ambition and greed drive people to engage in toxic behaviour to fight for whatever scarce rewards are on offer. Set against a backdrop of continuous demands on employees in a era of constant change and challenge, leadership practice in the 21st century is understandably seeped in complexity. Whilst conditions of scarcity are in fact constructed by employers in today’s lean environments, workplace toxicity has significant implications for organisational leaders in terms of work place disputes, absenteeism and litigation etc. Twentieth century hierarchial and autocratic leadership models are now deemed to be both obsolete and wholly inadedgate to inform leadership practice in the knowledge era. This conceptual article looks at the efficacy of complexity leadership theory (CLT) in empowering today’s leader to better understand and address 21st century workplace toxicity.

Calibrating ecological models or making decisions with them is an optimisation problem with challenging methodological issues. Depending on the optimisation formulation, there may be a large variety of optimisation configurations (e.g. multiple objectives, constraints, stochastic criteria) and finding a single acceptable solution may be difficult. The challenges are exacerbated by the high computational cost and the non linear or elusive mathematical properties that increased with the complexity of numerical models. From the feedbacks of practitioners, the need for a guideline for conducting optimisation of complex models has emerged. In this context, we propose a practical guide for the complex model optimisation process, covering both calibration and decision-making. The guide sets out the workflow with recommendations for each step based on existing tools and methods usually scattered throughout the literature. This guide is accompanied with an ODDO template (Overview, Design, Details of Optimisation) to standardise the published description of model-based optimisation and suggests research directions.

In contrast to lytic phages, filamentous phages are assembled in the inner membrane and secreted across the bacterial envelope without killing the host. For assembly and extrusion of the phage across the host cell wall, filamentous phages code for membrane-embedded morphogenesis proteins. In the outer membrane of E. coli, the protein gp4 forms a pore-like complex, while gp1 and gp11 form a complex in the inner membrane of the host. By comparing sequences with other filamentous phages, we identified putative Walker A and B motifs in gp1 with a conserved lysine in the Walker A motif (K14), and a glutamic and aspartic acid in the Walker B motif (D88, E89). In this work we demonstrate that both, Walker A and Walker B, are essential for phage production. The crucial role of these key residues suggest that gp1 is likely to be a molecular motor driving phage assembly. We further identified essential residues for the function of the assembly complex. Mutations in three out of six cysteine residues abolish phage production. Similarly, two out of six conserved glycine residues are crucial for gp1 function. We hypothesise that the residues represent molecular hinges allowing domain movement for nucleotide binding and phage assembly.

This study aims to understand the current state of research in urban resilience and to open a discussion about multi-level perspectives for this concept. Starting with the history of the concept of resilience, we identify three main stages in resilience concept’s evolution: conceptualization, contextualization and operationalization. Confusion occurs between sustainability and resilience, therefore we clearly separate these two concepts by creating conceptual maps. Such maps also underline the specificities of urban and regional resilience discourses. We illustrate that urban resilience research, operating within intra-urban processes, is oriented towards natural disasters, while regional resilience research, operating mostly within inter-urban processes, is oriented towards economic shocks. We show that these two approaches to resilience – urban and regional – are complementary, and we propose to integrate them into a multi-level perspective. By combining these two discourses, we propose a multi-level approach to urban resilience that takes into account both top-down and bottom-up resistance processes. In the discussion section, we propose to take the panarchy perspective as a theoretical framework for multi-level urban resilience, that explains the interactions between different levels through adaptive cycles, relationships between which can help to explain urban resilience.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

Bacteria currently included in Rhizobium leguminosarum are too diverse to be considered a single species, so we can refer to this as a species complex (the Rlc). We have found 429 publicly available genome sequences that fall within the Rlc and these show that the Rlc is a distinct entity, well separated from other species in the genus. Its sister taxon is R. anhuiense. We constructed a phylogeny based on concatenated sequences of 120 universal (core) genes, and calculated pairwise average nucleotide identity (ANI) between all genomes. From these analyses, we concluded that the Rlc includes 18 distinct genospecies, plus 7 unique strains that are not placed in these genospecies. Each genospecies is separated by a distinct gap in ANI values, usually at around 96% ANI, implying that it is a 'natural' unit. Five of the genospecies include the type strains of named species: R. laguerreae, R. sophorae, R. ruizarguesonis, "R. indicum" and R. leguminosarum itself. The 16S ribosomal RNA sequence is remarkably diverse within the Rlc, but does not distinguish the genospecies. Partial sequences of housekeeping genes, which have frequently been used to characterise isolate collections, can mostly be assigned unambiguously to a genospecies, but alleles within a genospecies do not always form a clade, so single genes are not a reliable guide to the true phylogeny of the strains. We conclude that access to a large number of genome sequences is a powerful tool for characterising the diversity of bacteria, and that taxonomic conclusions should be based on all available genome sequences, not just those of type strains.

The hybrid numbers are a generalization of complex, hyperbolic and dual numbers. In this paper, we introduce the Horadam hybrid polynomials called Horadam hybrinomials. We also give some special cases and algebraic properties of the Horadam hybrinomials. Finally we obtain some applications related to the Horadam hybrinomials in matrices.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

This paper discusses the concept of fractional derivative with complex order from the application point of view. It is shown that a fractional derivative is hermitian, if and only if the order is real. The hermitian part of complex order derivatives behave like allpass filters with almost logarithmic phase.

By using the new recently proposed extended rational methods, we set some solitary and multi wave solutions of the coupled Higgs system in the present study. Some new families of hyperbolic and trigonometric solutions of the coupled Higgs equations are successfully obtained. Some solutions are real as some are complex valued functions. Particular forms of some solutions derived by choice of some parameters are demonstrated in three dimensional spaces. The complex valued solutions are also depicted by plotting both real and complex component.

Sentinel lymph node dissection (sLND) using a magnetometer and superparamagnetic iron oxide nanoparticles (SPIONs) as a tracer was successfully applied in prostate cancer (PCa). Radioisotope-guided sLND combined with extended pelvic LND (ePLND) achieved better node removal, increasing the number of affected nodes or the detection of sentinel lymph nodes outside the established ePLND template. We determined the diagnostic value of additional magnetometer-guided sLND after intraprostatic SPION-injection in high-risk PCa. This retrospective study included 104 high-risk PCa patients (PSA >20 ng/ml and/or Gleason score ≥8 and/or cT2c) from a prospective cohort who underwent radical prostatectomy with magnetometer-guided sLND and ePLND. The diagnostic accuracy of sLND was assessed using ePLND as a reference standard. Lymph node metastases were found in 61 of 104 patients (58.7%). sLND had a 100% diagnostic rate, 96.6% sensitivity, 95.6% specificity, 96.6% positive predictive value, 95.6% negative predictive value, 3.4% false negative rate, and 4.4% false positive rate (detecting lymph node metastases outside the ePLND template). These findings demonstrate the high sensitivity and additional diagnostic value of magnetometer-guided sLND, exceeding that of ePLND through the individualized extension of PLND or the detection of sentinel lymph nodes / lymph node metastases outside the established node template in high-risk PCa.

The hybrid zone between chromosome races of the common shrew (Sorex araneus) provides an exceptional model to study the potential role of chromosome rearrangements in the initial steps of speciation. The Novosibirsk and Tomsk races differ by a series of Robertsonian fusions with monobrachial homology. They form a narrow hybrid zone and generate hybrids with both simple (chain of three chromosomes) and complex (chain of eight or nine) synaptic configurations. Using immunolocalisation of the meiotic proteins, we examined chromosome pairing and recombination in males from the hybrid zone. Homozygotes and simple heterozygotes for Robertsonian fusions showed a low frequency of synaptic aberrations (< 10%). The carriers of complex synaptic configurations showed multiple pairing abnormalities, which might lead to reduced fertility. Recombination frequency in the proximal regions of most chromosomes of all karyotypes was much lower than in the other regions. The strong suppression of recombination in the pericentromeric regions and co-segregation of race specific chromosomes involved in the long chains would be expected to lead to linkage disequilibrium between genes located there. Genic differentiation, together with the high frequency of pairing aberrations in male carriers of the long chains, might contribute to maintenance of the narrow hybrid zone.

This paper presents a new scientific contribution on the two-dimensional (2-D) subdomain technique in polar coordinates taking into account the finite relative permeability of the ferromagnetic material. The constant relative permeability corresponds to linear part of the nonlinear B(H) curve. As in conventional technique, the method of separation of variables and the Fourier’s series are used for the resolution of magnetostatic Maxwell’s equations in each region. Although, the general solutions of magnetic field in the subdomains and boundary conditions (BCs) between regions are different in the conventional and proposed method. In this later, the magnetic field solution in each subdomain is a superposition of two magnetic quantities in the two directions (i.e., r- and Q-axis) and the BCs between two regions are also in both directions. For example, the scientific contribution has been applied to an air- or iron-cored coil supplied by a constant current. The distribution of local quantities (i.e., the magnetic vector potential and flux density) has been validated by a corresponding 2-D finite-element analysis (FEA). The obtained semi-analytical results are in very good agreement with those of numerical method.

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

This paper presents a comparison between rain gauges, C-band and X-band radar data over an instrumented and regulated catchment of the Paris region, as well as their respective hydrological impacts with the help of flow observations and a semi-distributed hydrological model. Both radars confirm the high spatial variability of the rainfall down to their space resolution (respectively one kilometer and 250 m) and therefore underscore limitations of semi-distributed simulations. The use of the polarimetric capacity of the Météo-France C-band radar was limited to corrections of the horizontal reflectivity and its rainfall estimates are adjusted with the help of a rain gauge network. On the contrary, neither calibration was performed for the polarimetric X-band radar of the Ecole des Ponts ParisTech (below called ENPC X-band radar), nor any optimization of its scans. In spite of that and the non-negligible fact that the catchment was much closer to the C-band radar than to the X-band radar (20 km vs. 40 km), the latter seems to perform at least as well as the former, but with a higher scale resolution. This characteristic was best highlighted with the help of a multifractal analysis of the respective radar data, which also shows that the X-band radar was able to pick up a few extremes that were smoothed out by the C-band radar.

Korenaga and coworkers present evidence to suggest that 4.3 billion years ago the Earth’s mantle was dry and water filled the ocean to twice its present volume.[2] CO₂ was constantly exhaled during the mafic to ultramafic volcanic activity associated with magmatic plumes that produced the thick, dense and relatively stable oceanic crust. In that setting two distinct major types of sub-marine hydrothermal vents were active: ~400 °C acidic springs whose effluents bore vast quantities of iron into the ocean, and ~120 °C, highly alkaline and reduced vents exhaling from the cooler, serpentinizing crust at some distance from the heads of the plumes. When encountering the alkaline effluents, the iron from the plume head vents precipitated out forming mounds likely surrounded by voluminous exhalative deposits similar to the banded iron formations known from the Archean. These mounds and the surrounding sediments likely comprising nanocrysts of the variable valence FeII/FeIII oxyhydroxide, green rust. The precipitation of green rust, along with subsidiary iron sulfides and minor concentrations of Ni, Co and Mo in the environment at the alkaline springs may have established both the key bio-syntonic disequilibria, and the means to properly make use of them – those needed to drive the essential inanimate-to-animate transitions that launched life. In the submarine alkaline vent model for the emergence of life specifically it is first suggested that the redox-flexible green rust microcrysts spontaneously formed precipitated barriers to the complete mixing of carbonic ocean and alkaline hydrothermal fluids, barriers that created and maintained steep ionic disequilibria; and second, that the hydrous interlayers of green rust acted as 'engines' that were powered by those ionic disequilibria and drove essential endergonic reactions. There, aided by sulfides and trace elements acting as catalytic promoters and electron transfer agents, nitrate could be reduced to ammonia and carbon dioxide to formate, while methane may have been oxidized to methyl and formyl groups. Acetate and higher carboxylic acids could then have been produced from these C1 molecules and aminated to amino acids, and thence oligomerized to offer peptide nests to phosphate and iron sulfides and secreted to form primitive amyloid-bounded structures, leading conceivably to protocells.

Lifespan extension was recently achieved in Caenorhabditis elegans nematodes by mitochondrial stress and mitophagy, triggered via iron depletion. Conversely in man, deficient mitophagy due to Pink1/Parkin mutations triggers iron accumulation in patient brain and limits survival. We now aimed to identify murine fibroblast factors, which adapt their mRNA expression to acute iron manipulation, relate to mitochondrial dysfunction and may influence survival. After iron depletion, expression of the plasma membrane receptor Tfrc with its activator Ireb2, the mitochondrial membrane transporter Abcb10, the heme-release factor Pgrmc1, the heme-degradation enzyme Hmox1, the heme-binding cholesterol metabolizer Cyp46a1, as well as the mitophagy regulators Pink1 and Parkin showed a negative correlation to iron levels. After iron overload, these factors did not change expression. Conversely, a positive correlation of mRNA levels with both conditions of iron availability was observed for the endosomal factors Slc11a2 and Steap2, as well as for the iron-sulfur-cluster (ISC)-containing factors Ppat, Bdh2 and Nthl1. Positive correlation only after iron depletion was observed for the iron export factor Slc40a1, mitochondrial iron transporters Slc25a28, Abcb7 and Abcb8, mitochondrial ISC-containing factors Glrx5, Nfu1, Bola1 and Abce1, cytosolic Aco1 and Tyw5, as well as nuclear Dna2, Elp3, Pold1 and Prim2. The latter are regulators of nucleotide synthesis and DNA quality control, which have known importance for growth and lifespan. The only Pink1-/- triggered transcript modulation was the reduced expression of the ISC-containing ribosomal factor Abce1. These mammalian findings support previous fly data that Pink1 influences co-translational quality control via Abce1, as well as mitophagy. Our findings provide the first systematic survey how iron dosage triggers homeostatic transcriptional regulations and elucidate how iron deprivation results in mitophagy.

The aim of this paper is to bring together quaternions and generalized complex numbers. Generalized quaternions with generalized complex number components are expressed and their algebraic structures are examined. Several matrix representations and computational results are introduced. As a crucial part, alternative approach for generalized quaternion matrix with elliptic number entries are developed.

This year marks the 20th anniversary of the discovery that proteins with various cellular functions can be temporarily immobilized in the nucleolus, a process known as nucleolar sequestration. This review reflects on the progress made to understand the physiological roles of nucleolar sequestration and the mechanisms involved in protein immobilization. We discuss how nucleolar sequestration consists of a highly choreographed amyloidogenic liquid-to-solid phase transition that converts the nucleolus into Amyloid bodies (A-bodies). The study of solid condensates A-bodies will offer unique perspectives on cellular assembly of membrane-less compartments and provide alternative insights on pathological amyloidogenesis involved in neurological disorders.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is a devastating illness whose biomedical basis is now beginning to be elucidated. We reported previously that, after recovery from frozen storage, lymphocytes (peripheral blood monocytic cells, PBMCs) from ME/CFS patients die faster in culture medium than those from healthy controls. We also found that lymphoblastoid cell lines (lymphoblasts) derived from these PBMCs exhibit multiple abnormalities in mitochondrial respiratory function and signalling activity by the cellular stress-sensing kinase TORC1. These differences were correlated with disease severity, as measured by the Richardson and Lidbury Weighted Standing Test. The clarity of the differences between these cells derived from ME/CFS patient blood and those from healthy controls suggested that they may provide useful biomarkers for ME/CFS. Here we report a preliminary investigation into that possibility using a variety of analytical classification tools, including linear discriminant analysis, logistic regression and Receiver Operating Characteristic (ROC) curve analysis. We found that results from three different tests, lymphocyte death rate, mitochondrial respiratory function and TORC1 activity could each individually serve as biomarker with better than 90% sensitivity but only modest specificity vís a vís healthy controls. However, in combination they provided a cell-based biomarker with sensitivity and specificity approaching 100% in our sample. This level of sensitivity and specificity was almost equalled by a suggested protocol in which the frozen lymphocyte death rate was used as a highly sensitive test to triage positive samples to the more time consuming and expensive tests measuring lymphoblast respiratory function and TORC1 activity. This protocol provides a promising biomarker that could assist in more rapid and accurate diagnosis of ME/CFS.

Complex illumination condition is one of the most critical challenging problems for practical face recognition. In this paper, we propose a novel method to improve the illumination invariants for solving this challenge. Firstly, a new method based on the Lambert reflectance model is proposed to extract illumination invariant, which is less insensitive to complex illumination variations. Secondly, in order to repair the defects caused by process of illumination invariants extraction, Fast Mean Filter is utilized to smooth and remove noise. Lastly, for raising the richness of information in output image, a nonlinear normalization transformation is proposed. Compared with the state-of-the-arts, experimental results show that the proposed method can extract more robust illumination invariants. Apart from it, the richness of information in processed image is greater and superior performance in face recognition rate is superior.

We have developed an unsteady and non-linear wind synopsis simulator called RIAM-COMPACT (Research Institute for Applied Mechanics, Kyushu University, COMputational Prediction of Airflow over Complex Terrain) in order to simulate the airflow on a microscale, i.e., a few tens of km or less. In RIAM-COMPACT, the large-eddy simulation (LES) has been adopted for turbulence modeling. LES is a technique in which the structures of relatively large eddies are directly simulated and smaller eddies are modeled using a sub-grid scale model. In the present study, we have conducted the numerical wind diagnoses for Taikoyama Wind Farm nacelle separation accident in Japan. The simulation results suggest that all six wind turbines at the Taikoyama Wind Farm are subject to significant influence from separated flow (terrain-induced turbulence) which is generated due to the topographic irregularities in the vicinity of the wind turbines. A proposal has been also made on reconstruction of the wind farm.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is an enigmatic condition characterized by exacerbation of symptoms after exertion (post-exertional malaise or “PEM”), and by fatigue whose severity and associated requirement for rest are excessive and disproportionate to the fatigue-inducing activity. There is no definitive molecular marker or known underlying pathological mechanism for the condition. Increasing evidence for aberrant energy metabolism suggests a role for mitochondrial dysfunction in ME/CFS. Our objective was therefore to measure mitochondrial function and cellular stress sensing in actively metabolising patient blood cells. We immortalized lymphoblasts isolated from 51 ME/CFS patients diagnosed according to the Canadian Consensus Criteria and an age- and gender-matched control group. Parameters of mitochondrial function and energy stress sensing were assessed by Seahorse extracellular flux analysis, proteomics, and an array of additional biochemical assays. As a proportion of the basal oxygen consumption rate (OCR), the rate of ATP synthesis by Complex V was significantly reduced in ME/CFS lymphoblasts, while significant elevations were observed in Complex I OCR, maximum OCR, spare respiratory capacity, nonmitochondrial OCR and “proton leak” as a proportion of the basal OCR. This was accompanied by a reduction of mitochondrial membrane potential, chronically hyperactivated TOR Complex I stress signalling and upregulated expression of mitochondrial respiratory complexes, fatty acid transporters and enzymes of the β-oxidation and TCA cycles. By contrast, mitochondrial mass and genome copy number, as well as glycolytic rates and steady state ATP levels were unchanged. Our results suggest a model in which ME/CFS lymphoblasts have a Complex V defect accompanied by compensatory upregulation of their respiratory capacity that includes the mitochondrial respiratory complexes, membrane transporters and enzymes involved in fatty acid β-oxidation. This homeostatically returns ATP synthesis and steady state levels to “normal” in the resting cells, but may leave them unable to adequately respond to acute increases in energy demand as the relevant homeostatic pathways are already activated.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

Polymeric drag reducers have been developed over many years due to the great number of practical applications. In all of them, the molecular stability is an essential requirement. Usually, polymers break down under turbulent flows, which causes a decrease in their efficiency as drag reducers. Besides that, some specific applications, in agro and biomedical fields, impose a specific requirement that must be fulfilled, which is the use of non-toxic materials. A suitable stable material that is elected to accomplish this necessity is the mucilage of aloe vera, which is a bio-polymer that can be used as an alternative to the synthetic ones. Here, we investigate the role played by the aging of aloe vera on its capacity to reduce drag. The results obtained by ¹H nuclear magnetic resonance indicate that the compositions of young and mature leaves of aloe vera are different and such a difference plays an important role on their efficiency as drag reducers. Tests were performed to analyse the drag reduction in a rotating apparatus and in a pipeline system and the efficiencies of leaves of different ages were compared to their composition. The main conclusion of these experiments is that the young mucilage samples, which are richer in complex polysaccharides and exhibit lower acid contents, are more efficient drag reducers.

The pollen content of honey samples collected in the years 2017 and 2019 from experimental apiaries of Melipona seminigra pernigra Moure & Kerr 1950 installed in campo rupestre on canga (CRC) vegetation of the Serra dos Carajás, southeastern Amazonia, was analyzed to understand the local variability of floral resources occurring on natural and disturbed areas. Around one hundred pollen types were identified mainly belonging to Fabaceae, Myrtaceae and Euphorbiaceae (31, 6 and 5 types, respectively). The N5 mine presented the highest pollen richness with 95 pollen types identified, almost twice of those identified in the other areas, including the better preserved ones. Eighty percent of the pollen types are rare with concentrations ≤ 2,000 pollen grains/10 g; the remaining types are the most abundant and frequent, and are considered the primary bee sources (PBS). PBS correspond mostly to native plants such as Tapirira guianensis Aubl., Protium spp., Aparisthmium cordatum (A.Juss.) Baill., Mimosa acutistipula var. ferrea Barneby, Periandra mediterrânea (Vell.) Taub., Miconia spp., Pleroma carajasense K.Rocha, Myrcia splendens (Sw.) DC., Serjania spp. and Solanum crinitum Lam. All pollen types were identified during both seasons, but higher pollen concentration are related to the dry period (June-September). The statistical analysis indicated that there was no significant difference in honey pollen data between the natural and disturbed areas since the plant species considered as PBS in this work are intensively used in revegetation of degraded area (RDA) processes by mining activities.

We explores the relational, dynamic elements of Complex Buildings, a type of architecture designed to incubate uses, located in urban areas with high housing density. The uses of Complex Buildings concern different elements, including the network of agents using or managing them, the environment, and the activities and functions that take place occasionally, temporarily or permanently. Data was gathered through ethnographic research lasting 6 months and a chronotopian approach was used to describe time and space. We analyzed and discussed the interaction of the elements of Complex Buildings through a cellular automaton model, a computational method that simulates the growth of complex systems. It was used here to generate patterns that suggest configurations of uses that can optimize management and therefore increase economic and social capital. The cellular automaton model was also used to develop an abstraction of the Centquatre, a public cultural center in Paris. This center is a good example of a Complex Building, being based on a public-private partnership and having an architectural configuration designed to host a wide range of art, social and productive activities. The building includes a large central space used as an urban public area open to different types of people. The importance of this case study lies in its capacity to produce economic value by combining different uses, and also by welcoming different people to the public space. Regarding the building as a living organism, the cellular automaton model reveals the determinant nature of the concepts of configuration, compatibility of uses and economic value generated by the presence of people. We argue that this approach makes it possible to show that the space-time design and public space dimensions are determinant factors in Complex Buildings.

The bacterial wilt pathogen, first known as Bacillus solanacearum, has undergone numerous taxonomic changes since its first description in 1896. The history and significance of this pathogen is covered in this review with an emphasis on the advances in technology that were used to support each reclassification that finally led to the current separation of Ralstonia solanacearum into three genomic species. Frequent name changes occurred as methodology transitioned from phenotypic, biochemical, and molecular studies, to genomics and functional genomics. The diversity, wide host range and geographical distribution of R. solanacearum has resulted in its inclusion in a “species complex” as genomic analyses of elucidated phylogenetic relationships among strains. Current advances in phylogenetics and functional genomics now open new avenues for research into the epidemiology and control of the devastating bacterial wilt disease.

Ultra-thin Fe–6.5wt.%Si ribbons with 35 μm in thickness were prepared by melt-spinning. The magnetic properties were investigated before and after annealing 1000 ºC. DC properties and low-frequency (400 Hz ~ 10 kHz) iron losses have significantly improved after heat treatment. A simplified formula based on Steinmetz law which can be used to predict the AC iron loss is presented. According to the results of some iron losses data, a simplified formula has been determined, and the extent of AC iron losses can be predicted. The results obtained from the formula predict AC iron loss to a good degree. The method developed in this work could be extended to other magnetic materials for predicting AC iron loss with greater ease.

Although genome-wide association studies (GWAS) have identified several hundred loci associated with autoimmune diseases, their mechanistic insights are still poorly understood. The human genome is more complex than common single nucleotide polymorphisms (SNPs) that are interrogated by GWAS arrays. Some structural variants such as insertions-deletions, copy number variations, and minisatellites that are not very well tagged by SNPs cannot be fully explored by GWAS. Therefore, it is possible that some of these loci may have large effects on autoimmune disease risk. In addition, other layers of regulations such as gene-gene interactions, epigenetic-determinants, gene and environmental interactions also contribute to the heritability of autoimmune diseases. This review focuses on discussing why studying these elements may allow us to gain a more comprehensive understanding of the aetiology of complex autoimmune traits.

Biocompatible polymeric materials with potential to form functional structures in association with different therapeutic molecules have a high potential for biological, medical and pharmaceutical applications. Therefore, the protective capability of the inclusion nano-Complex formed between the sodium salt of poly(maleic acid-alt-octadecene) and a β-lactam drug (ampicillin trihydrate) on the chemical, enzymatic and biological degradation was evaluated. PAM-18Na was produced and characterized as reported previously. The formation of polymeric hydrophobic aggregates in aqueous solution was determined, using pyrene as a fluorescent probe. Furthermore, the formation of polymer-drug nano-complexes was characterized by Differential Scanning Calorimetry-DSC, viscometric, ultrafiltration/centrifugation assays, zeta potential and size measurements by dynamic light scattering-DLS. The PAM-18Na capacity to avoid the chemical degradation was studied through stress stability tests. The enzymatic degradation was evaluated from a pure β-lactamase, while the biological degradation was determined by different β-lactamase producing Staphylococcus aureus strains. When ampicillin was associated with PAM-18Na, the half-life time in acidic conditions increased, whereas both the enzymatic degradation and the minimum inhibitory concentration decreased to a 90 and 75%, respectively. These results suggest a promissory capability of this polymer to protect the β-lactam drugs against chemical, enzymatic and biological degradation.

The aim of this study was to develop a novel nanostructured lipid carriers (NLCs) with hepatocytes targeting as carriers for the magnetic resonance imaging (MRI) contrast agent (i.e., magnetic nanostructured lipid carriers, MNLCs), and to evaluate the targeting ability of the MNLCs with T2-weighted MRI both in vitro and in vivo. Here, the galactose-octadecylamine (Gal-ODA) conjugates were synthesized by chemical coupling reaction between lactose acid (LA) and octadecylamine (ODA). Then the superparamagnetic iron oxide (SPIO) loaded nanostructured lipid carrier (conjugated by Gal-ODA, Gal-NLC-SPIO) was prepared by emulsification-ultrasonic method using monoglyceride as lipid materials. The Gal-NLC-SPIO with a diameter of about 50 nm could specifically internalize into LO2 (human hepatic cell line) cells. In vitro MRI results also proved the specific targeting ability of Gal-NLC-SPIO to LO2 cells. The in vivo MR imaging experiments using an orthotopic intrahepatic xenograft tumor model further validated the hepatocytes targeted effect of Gal-NLC-SPIO. The results of this study suggested that Gal-NLC-SPIO can be used as a contrast agent to aid in the diagnosis of hepatic diseases.

Chitosan is a cationic polysaccharide usually obtained by alkaline deacetylation of chitin poly(N-acetylglucosamine). It is biocompatible, biodegradable, mucoadhesive and non-toxic. These excellent biological properties make chitosan a good candidate for a platform in developing drug delivery systems having improved biodistribution, increased specificity and sensitivity, and reduced pharmacological toxicity. In particular, chitosan nanoparticles are found to be appropriate for non-invasive routes of drug administration: oral, nasal, pulmonary and ocular routes. These applications are facilitated by the absorption-enhancing effect of chitosan. Many procedures for obtaining chitosan nanoparticles have been proposed. Particularly, the introduction of hydrophobic moieties into chitosan molecules by grafting to generate a hydrophobic-hydrophilic balance promoting self-assembly is a current and appealing approach. The grafting agent can be a hydrophobic moiety forming micelles that can entrap lipophilic drugs or it can be the drug itself. Another suitable way to generate self-assembled chitosan nanoparticles is through the formation of polyelectrolyte complexes with polyanions. This paper reviews the main approaches for preparing chitosan nanoparticles by self-assembly through both procedures and illustrates the state of the art of their application in drug delivery.

Recently emerging data-driven citizen sciences need to harness increasing amount of massive data with varying quality. This paper develops essential theoretical frameworks and example models and examine its computational complexity for interactive data-driven citizen science within the context of guided self-organization. We first define a conceptual model that incorporates quality of observation in terms of accuracy and reproducibility, ranging between subjectivity, inter-subjectivity, and objectivity. Next, we examine the database's algebraic and topological structure in relation to informational complexity measures, and evaluate its computational complexities with respect to exhaustive optimization. Conjectures of criticality are obtained on self-organizing processes of observation and dynamical model development. Example analysis is demonstrated with the use of biodiversity assessment database, the process that inevitably involves human subjectivity for the management in open complex systems.

Keywords: iron deficiency anemia; IDA; anemia; knowledge; awareness.

Several observations have shown that patients with polycythemia have iron deficiency. Our objectives were to report the prevalence of iron deficiency, to evaluate the diagnostic performance of serum ferritin in polycythemia vera and to describe the mechanisms of this association. This is a retrospective descriptive and analytical study carried out in the internal medicine department of the Henri Mondor Hospital, Aurillac, France. The study involved 114 patients with polycythemia, followed in the department from January 1, 2010 to December 31, 2021. To evaluate the diagnostic performance, the JAK2 mutation was considered as the gold standard of diagnosis. Thirty-three patients had polycythemia vera and 76 patients had secondary polycythemia. The mean age of the patients was 61.79 years (±15.44) with a sex ratio of 4.43. The overall prevalence of iron deficiency was 21.05%. The prevalence was 53% in polycythemia vera group and 1.32% in secondary polycythemia group. The risk of iron deficiency was high in polycythemia vera (OR=115; 95% CI [14.4-918.2], p<0.000). The sensitivity and specificity of serum ferritin were 52.63% and 100% respectively. Assessment of iron deficiency should be part of the initial evaluation of polycythemia. The presence of iron deficiency is specific for polycythemia vera.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Background: Iron chelation medications (desferoxamine, desferasirox, desferiprone) are used to manage iron overload. These medications are partially excreted via the kidneys, desferoxamine and desferiprone excretes primarily in the urine, and desferasirox had about 8% excreted in the urine. Their use in severe kidney disease and dialysis patients is caution as “avoided” concerning adverse effects; however, there are reports safe use. This manuscript reviews the literature in this population. Data Sources: Pubmed: desferasirox, deferiprone, deferoxamine, kidney disease, ESKD, Dialysis. Case reports and case series that described experiences with using iron chelation medications in ESKD patients are included. Data also gathered from reading-related sources. Results: This is a review of desferoxamine, desferasirox, and deferiprone use in kidney disease from 1976 to the present time. Table 1 provides a summary of findings. These are mostly reports and brief descriptions of the experiences used in severe kidney disease and dialysis, but lack of randomized control trials and small number of participants. Conclusions: Iron chelation medications are important for treating iron overload but concerns with adverse effects. Due to limited medications available to treat iron overload in patients with severe kidney disease, their safe use has been reporting in the literature. This is an area that warrants further research.

Activation of the NLRP3 inflammasome plays a crucial role in innate immune response. During cell division, the NLRP3 inflammasome activation must be strictly controlled. Here, we discovered the anaphase promoting complex subunit 10 (Anapc10, APC10), a substrate recognition protein of the anaphase promoting complex/cyclosome (APC/C), is a critical mediator of the NLRP3 inflammasome activation. APC10 protein interacts with NLRP3, and co-localizes with NLRP3 protein in the cytoplasm. During interphase, APC10 interacts with NLRP3 to promote the NLRP3 inflammasome activation. During mitosis, APC10 disassociates from the NLRP3 inflammasome to inhibit the inflammatory responses. This study reveals a distinct mechanism by which APC10 serves as a switch of the NLRP3 inflammasome activation during cell cycle.

In recent years, numerous topologies of single phase and three phase Field Excited Flux-Switching Machine (FEFSM) have been developed for several applications. Comparative study of three types of single-phase low-priced Field Excited Flux-Switching Machine (FEFSM) is presented in this paper. Both the conventional 8S/4P sub-part rotor design and 6S/3P salient rotor design have an overlapped winding arrangements between armature coil and field excitation coil that depicts high copper losses as well as results in increased size of motor. Additionally, FEFSM with salient structure of the rotor have high flux strength in the stator-core that has much impact on high iron losses. Copper consumption and iron loss being a crucial proportion in total machine losses. Therefore a novel topology of single phase modular rotor field excited FSM with 8S/6P configuration is proposed, which enable non-overlap arrangement between armature coil and FEC winding that facilitates devaluation in the copper losses. The proposed modular rotor design acquires reduced iron losses as well as reduced active rotor mass comparatively to conventional rotor design. It is very persuasive to analyze the best range of speed for these rotors to avoid cracks and deformation, the maximum tensile strength (can be measured with principal stress in research) of the rotor analysis is conducted using JMAG. A deterministic optimization technique is used to enhance the performance of 8S/6P modular rotor design. The electromagnetic performance of conventional sub-part rotor design, F1-A3-3P design and proposed novel-modular rotor design are analyzed by 3D-Finite Element Analysis (3D-FEA), includes flux linkage, flux distribution, flux strength, back-EMF, cogging torque, torque characteristics, iron losses and efficiency.

Abstract: COVID-19 in 2020 brought challenges to the Brazilian public health system with an emerging virus with respiratory contagion called SARS-CoV-2. There are few studies in Brazil and in some countries, on the increased incidence of certain viral respiratory infections, includ-ing H1N1 and coronavirus and their association with low levels of vitamin D, zinc and iron. The aim of this study was to demonstrate that the deficit of vitamin D, zinc and iron has an impact on the infectious process of patients with COVID-19 and to establish new forms of prevention for the worsening of COVID-19 in the human body. Data were collected from medical records and test results from patients being followed up during the treatment period for COVID-19. Patients with low blood levels of vitamin D, zinc and iron during the treatment period of COVID-19 had a higher percentage of worsening and complications requiring hospitalization in intensive care beds. The ingestion of vitamin D, zinc and iron in the treatment period of patients with COVID-19 in addition to being an immunological protector against SARS-CoV-2 and alleviating the process of worsening the disease can also act as a biomarker in cases of this disease.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

The nature of the sustainability crisis is characterized by high levels of complexity, thus it is not amenable to be approached from the linearity or reductionist paradigm. Emergence is a multilevel phenomenon that is characterized by qualitative novelty and is recognized as an important attribute of complex systems produced by self-organized processes, unveiled from a holistic stance. This conceptual-analytical article explores the emergence phenomenon and questions whether it can be a way of enhancing the solution process to meet the sustainability challenges. Emergent properties or behaviors emerge only when the system parts interact in a wider whole. Moreover, a systemic approach is proposed as an intermediary component in the process of emergence of creative and wise solutions to the wicked problems of unsustainability. This requires observation and entails analyzing open systems as a whole and recognizing the impact of traversing macro- and micro- scales on causal and creative emergence. The study also emphasizes synergies between emergence and creativity aimed at sustainability. Sustainable development requires leapfrogging past conventional practices, in an accelerated way, and the emergence phenomenon at play between systems levels, coupled with purposefully structured creative processes, holds the potential for catalyzing sustainable development efforts.

This paper proposes a procedure for predicting the actual wind speed for flow over complex terrain with CFD. It converts a time-series of wind speed data acquired from field observations into a time-series of actual scalar wind speed by using non-dimensional wind speed parameters which are determined beforehand with the use of CFD output. The accuracy and reproducibility of the prediction procedure were examined by simulating the flow with CFD with the use of high resolution (5 m) surface elevation data for the Noma Wind Park in Kagoshima Prefecture, Japan. The errors of the predicted average monthly wind speeds relative to the observed values were less than approximately 20%.

Decision-makers are concerned with the inherent complexity of the modern world's markets. However, price fluctuations, environmental concerns, technological development, emerging markets, political challenges, and social expectations made the 21^st century's more dynamic and complex. From a policy-making perspective, it is vital to uncover future trends. This paper proposed that artificial intelligence can improve interpretations in complex markets, such as financial and energy markets. In a complex environment, it is critical to investigate maximum available input features to ensure no valuable informative feature is neglected. Some AI-based models are investigated and presented that AI-based models can successfully uncover future trends. From a scenario development perspective purified input features subset refer to driving forces which shape alternative futures. Results showed that using AI can improve our understanding of how input features influence future behaviors and simultaneously improves prediction accuracy and reliability.

The origin and significance of the tonalite–trondhjemite–granodiorite (TTG) units and the familiar metabasite xenoliths they host in the Yangtze Craton, China, remain controversial, and resolving these issues is important if we are to understand the evolution of the early Yangtze Craton. We focused on biotite–tremolite schist xenoliths in the Archean TTG units of the Kongling high-grade metamorphic terrane, and U–Pb dating of their zircons yielded ²⁰⁷Pb/²⁰⁶Pb ages of ca. 3.00 Ga, which provides a minimum age for the formation of the pre-metamorphic basic igneous rock. The host TTGs and late intrusive granitic dikes yield three groups of upper intercept ages at 2.87–2.88, 2.91–2.94, and 3.07 Ga, and a concordant age at 2.94 Ga, which suggest that the Yangtze continental nucleus underwent three important metamorphic–magmatic events in the Mesoarchean at ca. 3.00, 2.94, and 2.87 Ga. The biotite–tremolite schists have high ratios of K₂O/Na₂O and high contents of CaO, Cr, and Ni, thus showing the characteristics of high-K calc-alkaline island-arc volcanic rocks (basalt–andesite) that form by the partial melting of subducted oceanic crust. The data also provide further proof that a Mesoarchean metamorphic basement exists in the Yangtze Plate. Derivation of the magmatic protoliths of the biotite–tremolite schist enclaves from an oceanic crust during slab subduction, and the presence of these xenoliths within the TTG suite, indicate the existence of the initiation of plate tectonics during the Mesoarchean (≤2.94 Ga).

Nuclear receptor coactivator 4 (NCOA4) is a selective cargo receptor that mediates the autophagic degradation of ferritin (“ferritinophagy”), the cytosolic iron storage complex. NCOA4-mediated ferritinophagy maintains intracellular iron homeostasis by facilitating ferritin iron storage or release according to demand. Ferritinophagy is involved in iron-dependent physiological processes such as erythropoiesis, where NCOA4 mediates ferritin iron release for mitochondrial heme synthesis. Recently, ferritinophagy has been shown to regulate ferroptosis, a newly described form of iron-dependent cell death mediated by excess lipid peroxidation. Dysregulation of iron metabolism and ferroptosis have been described in neurodegeneration, cancer, and infection, but little is known about the role of ferritinophagy in the pathogenesis of these diseases. Here, we will review the biochemical regulation of NCOA4, its contribution to physiological processes and its role in disease. Finally, we will discuss the potential of activating or inhibiting ferritinophagy and ferroptosis for therapeutic purposes.