Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

Background. Escherichia coli commonly causes catheter-related bloodstream infection (C-RBSI) in specific populations. The differential time to positivity (DTTP) technique is the recommended conservative procedure for diagnosing C-RBSIs. Methods. We conducted a retrospective study of episodes in which E. coli was isolated from catheter lumens obtained using the DTTP technique. We analysed microbiological and clinical data based on the DTTP technique as either catheter colonization, C-RBSI, or non-C-RBSI. Results. We included 89 catheter blood cultures classified as follows: catheter colonization, 33.7%; C-RSBI, 9.0%; and non-C-RBSI, 57,3%. Catheter withdrawal was 15.7% without positive catheter-tip cultures. We found no statistically significant differences in catheter type, antibiotic treatment, or clinical outcome among groups, except for the frequency of catheter lock therapy or in the frequency of successful treatment. Mortality was associated with C-RBSI in only 1 patient. Conclusion. E. coli bacteremia diagnosed by the DTTP technique was non-catheter related in most patients. As the majority of the catheters were retained, E. coli bacteremia could not be microbiologically confirmed or ruled out as catheter related by catheter-tip culture. Future studies are needed to assess the profitability of the DTTP technique for diagnosing E. coli C-RBSIs..

We primarily investigate the existence of solutions for fractional neutral integro-differential equations subjected to Neumann-type boundary conditions, which is crucial for understanding natural phenomena. Taking into account factors such as neutral type, fractional-order integrals, and fractional-order derivatives, we employ probability density functions, Laplace transforms, and resolvent operators to formulate a well-defined concept of a mild solution for the specified equation. Following this, by integrating fixed point theorems, we establish the existence of mild solutions under more relaxed conditions.

Uncertain fractional differential equation (UFDE) is an excellent tool for describing complicated dynamic systems. This paper analyzes the valuation problems of currency option based on UFDE under optimistic value criterion. Firstly, an uncertain fractional currency model is formulated to describe the dynamics of foreign exchange rate. Then, the pricing formulae of European, American and Asian currency option are obtained under optimistic value criterion, respectively. Finally, numerical simulations are provided to illustrate the validity of our theoretical results.

We investigate a singularly perturbed q-difference differential Cauchy problem with polynomial coefficients in complex time and space with quadratic nonlinearity. We construct local holomorphic solutions on sectors in the complex plane with respect to the perturbation parameter with values in some Banach space of formal power series in space with analytic coefficients on shrinking domains in time. Two aspects of these solutions are addressed. One feature concerns asymptotic expansions in the parameter for which a Gevrey type structure is unveiled. The other fact deals with confluence properties as q tends to 1. In particular the built up Banach valued solutions are shown to merge in norm to a fully bounded holomorphic map in all its arguments that solves a nonlinear partial differential Cauchy problem.

Multivariate Time Series Classification (MTSC) is one of most important tasks in time series analysis, aiding in activities such as human motion recognition and medical diagnostics. Existing methods for MTSC do not explicitly model temporal differences and generalize the idea of temporal difference into a efficient temporal module. Additionally, existing methods are not yet able to capture cross-variable relationships well during network training. As a result, they are unable to achieve convincing feature representation, leading to suboptimal classification accuracy. In this paper, we propose a novel MTSC model called Temporal Difference and Cross-variate Fusion Network (TDCFN), which integrates a two-stream differential LSTM network and a cross-variate feature extraction network to enhance feature representation. TDCFN achieves superior classification accuracy by capturing dynamic temporal evolution and inter-variable relationships. The experimental results show that TDCFN can achieve competitive performance with state-of-the-art multivariate time series classification approaches.

1,3,5-Tris-(α-naphthyl)benzene is an organic non-electrolyte with notable stability of an amorphous phase. Its glassy and supercooled liquid states were previously studied by spectroscopic and calorimetric methods. However, the thermodynamic parameters of phase transitions available from the literature are inconsistent. In this work, the heat capacities of crystalline and liquid phases, the temperature dependence of the saturated vapor pressures, fusion and vaporization enthalpies were determined using differential and fast scanning calorimetry and verified using the estimates based on solution calorimetry. The structural features of 1,3,5-tris-(α-naphthyl)benzene are discussed based on the computations performed and the data on the molecular refractivity. The consistency between the values obtained by independent techniques was demonstrated. The deviations in the previously published data were attributed to possible polymorphism.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

The classical Lotka-Volterra predator-prey model is globally stable and uniformly persistent. However, in real-life biosystems extinction of species due to stochastic effects is possible. In this paper, we consider the classical Lotka-Volterra predator-prey model under stochastic perturbations. For this model, using an analytical technique based on the direct Lyapunov method and a development of the ideas of R.Z. Khasminskii, we find the precise sufficient conditions for the stochastic extinction of one and both species and the precise necessary conditions for the stochastic system persistence. The stochastic extinction occurs via a process known as the stabilization by noise of the Khasminskii type, and, in order to establish the sufficient conditions for extinction, we found the conditions for the stabilization. The analytical results are illustrated by numerical simulations. {\bf Keywords:} stochastic perturbations, white noise, Ito's stochastic differential equation, the Lyapunov functions method, stability in probability, stabilization by noise, stochastic extinction, persistence.

This paper presents a comprehensive investigation into the applicability and performance of two prominent growth models, namely the Verhulst model and the Montroll model, in the context of modeling tumor cell growth dynamics. Leveraging the power of Physics-Informed Neural Networks (PINNs), we aim to assess and compare the predictive capabilities of these models against experimental data obtained from the growth patterns of tumor cells. We employ a dataset comprising detailed measurements of tumor cell growth to train and evaluate the Verhulst and Montroll models. By integrating PINNs, we not only account for experimental noise but also embed physical insights into the learning process, enabling the models to capture the underlying mechanisms governing tumor cell growth. Our findings reveal the strengths and limitations of each growth model in accurately representing tumor cell proliferation dynamics. Furthermore, the study sheds light on the impact of incorporating physics-informed constraints on the model predictions. The insights gained from this comparative analysis contribute to advancing our understanding of growth models and their applications in predicting complex biological phenomena, particularly in the realm of tumor cell proliferation.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

The method for quantitative analysis is based on the direct measurement of the analyte using differential pulse voltammetry (DPV), exploiting its oxidation peak. Calibration curves are set up to evaluate the figures of merit of the analytical method (LOD, LOQ, linear range). The application of the sensor for the dosing of GA in real matrices is carried out by analyzing non-alcoholic and alcoholic beverages and comparing the results with those reported in the literature and with the content of total polyphenols determined by the Folin-Ciocalteu method. In all cases, concentrations of GA align with those previously found in the literature for the beverages examined. Moreover, the values are always lower than the total polyphenols content; this demonstrates the good selectivity of the sensor that can discriminate the target molecule from other polyphenols present.

In our study we investigated the accelerated aging process of PLA under 253.7 nm UV-C irradiation with the use of GPC, NMR, FTIR, DSC methods and formal kinetic analysis. The results of GPC and DSC indicated a significant degree of destructive changes in PLA macromol-ecules, while spectroscopic methods NMR and FTIR showed maintenance of PLA main structural elements even after a long time of UV exposure. In addition to that, the GPC method displayed the formation of a high-molecular fraction starting from 24 hours of irradiation, and an increase in its content after 144 hours of experiment. It has been showed for the first time that a distinctive feature of prolonged UV exposure is the occurrence of intra- and intermolecular radical recom-bination reactions, leading to the formation of a high-molecular fraction of PLA decomposition products. This causes the observed slowdown of the photolysis process. It was concluded that photolysis of PLA is a complex of physicochemical processes, the mechanism of which depends on morphological changes in a solid phase of the polymer under UV radiation.

Use of MS Excel as a platform for teaching simple iterative solution of partial differential equations runs into issues of reliability of the computation because of the large number of calculations required. This article documents the problem and an empirical solution. The cause of this unreliability was found by detailed examination of the numerical results from three simultaneous iterations. Computers of several types from different manufacturers were found to fail occasionally in updating variables in the numerical iteration. A simple work-around is suggested and was tested on several platforms.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

This study focuses on the optimal deployment problem, and determines the optimal size of a military force to send to the battle field. The decision is optimized, based on an objective function, that considers the cost of deployment, the cost of the time it takes to win the battle, and the costs of killed and wounded soldiers with equipment. The cost of deployment is modeled as an explicit function of the number of deployed troops and the value of a victory with access to a free territory, is modeled as a function of the length of the time it takes to win the battle. The cost of lost troops and equipment, is a function of the size of the reduction of these lives and resources. An objective function, based on these values and costs, is optimized, under different parameter assumptions. The battle dynamics is modeled via the Lanchester differential equation system based on the principles of directed fire. First, the deterministic problem is solved analytically, via derivations and comparative statics analysis. General mathematical results are reported, including the directions of changes of the optimal deployment decisions, under the influence of alternative types of parameter changes. Then, the first order optimum condition from the analytical model, in combination with numerically specified parameter values, is used to determine optimal values of the levels of deployment in different situations. A concrete numerical case, based on documented facts from the Battle of Iwo Jima, during WW II, is analyzed, and the optimal US deployment decisions are determined under different assumptions. The known attrition coefficients of both armies, from USA and Japan, and the initial size of the Japanese force, are parameters. The analysis is also based on some parameters without empirical documentation, that are necessary to include to make optimization possible. These parameter values are motivated in the text. The optimal solutions are found via Newton- Raphson iteration. Finally, a stochastic version of the optimal deployment problem is defined. The attrition parameters are considered as stochastic, before the deployment decisions have been made. The attrition parameters of the two armies have the same expected values as in the deterministic analysis, are independent of each other, have correlation zero, and have relative standard deviations of 20%. All possible deployment decisions, with 5000 units intervals, from 0 to 150000 troops, are investigated, and the optimal decisions are selected. The analytical, and the two numerical, methods, all show that the optimal deployment level is a decreasing function of the marginal deployment cost, an increasing function of the marginal cost of the time to win the battle, an increasing function of the marginal cost of killed and wounded soldiers and lost equipment, an increasing function of the initial size of the opposing army, an increasing function of the efficiency of the soldiers in the opposing army and a decreasing function of the efficiency of the soldiers in the deployed army. With stochastic attrition parameters, the stochastic model also shows that the probability to win the battle is an increasing function of the size of the deployed army. When the optimal deployment level is selected, the probability of a victory is usually less than 100%, since it would be too expensive to guarantee a victory with 100% probability. Some of many results of relevance to the Battle of Iwo Jima, are the following: In the deterministic Case 0 analysis, the optimal US deployment level is 66200, the time to win the battle is 30 days and 14000 US soldiers are killed or wounded. If the marginal cost of the time it takes to win a victory doubles, the optimal deployment increases to 75400, the time to win a victory is reduced to 26 days, and less than 12000 soldiers are killed or wounded. In the stochastic Case 0 analysis, the optimal US deployment level is 65000, the expected time to win the battle is 46 days and almost 25000 US soldiers are expected to be killed or wounded. If the cost per killed or wounded soldier increases from 0 to 5 M $US, the optimal deployment level increases to 75000. Then, the victory is expected to appear after 35 days and 19900 US soldiers are expected to be killed or wounded.

This study aims to categorize the morphological changes during cabbage (B. oleracea ssp. capitata) development: seedling, rosette, folding, and heading and to elucidate the cellular mechanisms of leaf curvature, essential for the formation of the leafy head. We followed the growth of two cabbage morphotypes with distinct head shapes (round and pointed); we phenotyped the size and volume of the whole-plant as well as the size, shape, and curvature of the leaves during growth. By integrating these phenotypic data, we determined the four vegetative stages for both cabbages. Cytological phenotypes of microtome sections from five distinct leaf positions of the rosette, folding, and heading leaves at two timepoints during leaf growth were quantified and revealed variations in cellular parameters among leaf types, between leaf positions, and between the adaxial and abaxial sides. We identified two synergistic cellular mechanisms contributing to the curvature of heading leaves: differential growth across the leaf blade, with increased growth at the leaf's centre relative to the margins; and increased expansion of the spongy parenchyma layer compared to the palisade parenchyma layer, resulting in the direction of the curvature, which is inwards. These two processes together contribute to the typical leafy heads of cabbages.

We introduce a novel stochastically correlated two-factor (i.e., bivariate) diffusion process under the square-root format, for which we obtained, analytically, the corresponding solutions for the conditional moment generating functions and conditional characteristic functions. Such solutions recover verbatim those of the uncorrelated case. We believe that the The aforementioned model encompasses a range of processes similar to that produced by a bivariate square-root process in which entries are correlated in the standard way, i.e., via a constant correlation coefficient. Note that, for the latter, closed-form solutions for the conditional characteristic functions are not available. We focus on the financial scenario of obtaining closed-form expressions for the exact price of a zero-coupon bond and Asian option prices via a Fourier cosine series method.

Evolutionary algorithms find applicability in reinforcement learning of neural networks due to their independence from gradient-based methods. To achieve successful training of neural networks using evolutionary algorithms, careful considerations must be made to select appropriate algorithms due to the availability of various algorithmic variations. In Part1 and Part2, the author previously reported experimental evaluations on Genetic Algorithm and Evolution Strategy for reinforcement learning of neural networks, utilizing the Acrobot control task. This article constitutes Part3 of the series of comparative research. In this study, Differential Evolution is adopted as the third instance of major evolutionary algorithms. The experimental results show a statistically significant superiority of DE over both GA and ES (p < .01). In addition, DE exhibits its robustness to variations in hyperparameter configurations (the number of offsprings and generations). In the previous experiments, both ES and GA showed significant performance differences depending on the configurations, whereas in the experiment reported in this article, such differences are not detected for DE.

In this paper, we consider an epidemiological Susceptible-Infected-Susceptible (SIS) model in which the individuals cured from the infection return back into the group of people endangered by the infection. Delay differential equations were introduced to create more realistic models since many processes depend on past history. Many different mathematical methods, including the Susceptible-Infected-Recovered (SIR) model as well as derivatives thereof, can be used to prognose the spread of many various infectious diseases, including Covid-19.We use a nonlinear differential system with time delay as a mathematical formulation of this model. It is examined by the existence of a positive solution which is bounded by two functions $k_1, k_2\in C([t_0,\infty),(0,\infty))$ with constants $\lambda_1 > 0,\,\lambda_2 > 0$ where $0<\lambda_1\leq \lambda_2$. The conditions are put in place for existence of a positive solution that approaches zero in infinity, if $t\to\infty$. Infectious diseases accompany a person throughout their entire life, and in the history of mankind often appeared in frequent epidemics caused high mortality. The occurrence of infectious diseases in the population represents a serious health, social and economic problem. There is a lot of ambiguity concerning the time span and final spread of the epidemic thus making it very demanding for the governing bodies, healthcare institutions, and economic sector to precisely judge the future development.Several examples are shown at the end of this paper.

To identify the exchange coefficients of a nonlinear polynomial tricompartmental general system of α+β , we follow the procedure; firstly, the recommended solution is to introduce an adequate time t*&gt;0 in a determinable manner. That is, after injecting quantity a into the main compartment, wait a moment for the exchange in the polynomial α+β order nonlinear general system to settle, and then compare this compartment to compartment 2 at t*. Secondly, applying the Taylor formula will linearize the system and identify the exchange coefficients. Finally, we will prove that the linearization method is stable.

Vectorial Boolean functions and codes are closely related, and each corresponding domain gives been to each other. On the one hand, various requirements of binary linear codes are needed for their theatrical interests but, more importantly, for their practical applicants (such as few-weight codes or minimal codes for secret sharing, locally recoverable codes for storage, etc.). On the other hand, various criteria and tables have been introduced to analyse the security of S-boxes that are related to vectorial Boolean functions, such as the Differential Distribution Table (DDT), the Boomerang Connectivity Table (BCT), and the Differential-Linear Connectivity Table (DLCT). In previous years, two new tables have been proposed for which the literature was pretty abundant: the $c$-DDT to extend the DDT and the $c$-BCT to extend the BCT. In the same vein, we propose extended concepts to study further the security of vectorial Boolean functions, especially the $c$-Walsh transform, the $c$-autocorrelation, and the $c$-differential-linear uniformity, and its accompanying table, the $c$-Differential-Linear Connectivity Table ($c$-DLCT). We study these properties of the novel functions at their optimal level concerning these concepts and describe the $c$-DLCT of the crucial inverse vectorial (Boolean) function case. Finally, the derived functions could lead to new families of binary minimal codes, as the recent achievements on minimal codes from low differential uniformity. We draw new avenues for future research toward linear code designs.

The pollution caused by nitrogen dioxide is a major environmental problem in China. This study introduces a new type of atmospheric trace gas remote-sensing instrument, an airborne fiber imaging spectrometer. This spectrometer has a spectral range of 300–410 nm and works in push-broom mode with a 30° field of view on a flight path. Flight experiments were conducted on December 30, 2022 and January 5, 2023, covering heavily polluted areas of east of Beijing and Tangshan. This equipment obtained the density distribution of NO2 over the flight area. The results showed that pollution was mainly concentrated in the Caofeidian area and at the power station in the north, and the main source of pollution was anthropogenic. Satellite and airborne data near the pollution points were compared, and the two datasets showed a positive correlation with a correlation coefficient of 0.78 and 0.7, on the two days, respectively. This study demonstrates the capability of an airborne fiber imaging spectrometer for NO2 regional emission remote sensing and identifying the pollution points.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

The paper focuses on the different dynamical systems for the prey-predator model for different cases which includes greater depth of the food chain and varying number of preys and predators. We simulate the different postulated models and provide a comparative study for the same.

This study proposes a methodology for identifying time intervals in which time-of-use (ToU) energy tariffs can be set. This is achieved by analyzing the variability in electric power demand and esti-mating the potential for demand flexibility. The proposed methodology is as follows: first, data preprocessing is performed, focusing on the organization and cleaning of individual consumption records. Subsequently, the data are processed and classified by using consumption variability analysis and clustering techniques. Then, representative clusters are selected and time intervals are analyzed to identify periods of high electric power consumption variability. This methodology was tested with real data from smart meters in the Colombian electrical system, in which time intervals with potential for settinh ToU tariffs were ultimately identified. This work promotes the implementation of demand response strategies that enhance sustainability and facilitate the transition to a more resilient energy landscape both nationally and internationally. The findings are expected to contribute to the formulation of tariff schemes that encourage con-scious changes in electric energy consumption patterns.

Homotopy perturbation and analysis methods have been widely used to obtain both approximate and exact so- lutions to nonlinear problems. In general, these two methods are based on the Taylor series with respect to an embedding parameter. Many researchers have compared the two methods and raised more concerns on the homo- topy perturbation method (HPM) because the homotopy analysis method (HAM) contains a convergence-control parameter ~: For this reason, in this article, a more general form of HPM is introduced as the -homotopy per- turbation method (-HPM), which contains a control parameter : The introduction of parameter  in this new modication gives a better way to adjust and control the convergence region and the rate of the series solution. We conrm through the given examples in this study that the HPM is a special case of the -HPM. The error and convergence analysis of this proposed method are also presented

The influence of polysialic acid (PSA) and sialic acid (SA) on the gut microbial community composition and metabolites in healthy human was investigated using a bionic gastrointestinal reactor. The results indicated that PSA and SA significantly changed the gut microbiota and metabolites in different degrees. PSA can increase the relative abundances of Faecalibacterium and Allisonella, whereas SA can increase those of Bifidobacterium and Megamonas. Both can significantly increase the content of short-chain fatty acids. The results of metabolome analysis showed that PSA can upregulate ergosterol peroxide and gallic acid and downregulate the harmful metabolite N-acetylputrescine. SA can upregulate 4-pyridoxic acid and lipoic acid. PSA and SA affect gut microbiota and metabolites in different ways and have positive effects on human health. These results will provide reference for the further development of PSA- and SA-related functional foods and health products.

Advanced methods of treatment are needed to fight the threats of virus-transmitted deseases and pandemics. Often they are based on an improved biophysical understanding of virus replication strategies and processes in their host cells. For instance, an essential component of the replication of the Hepatitis C virus (HCV) proceeds under the influence of non-structural HCV proteins (NSPs) that are anchored to the endoplasmatic reticulum (ER), such as the NS5a protein. The diffusion of NSPs has been studied by in-vitro fluorescence recovery after photobleaching (FRAP) experiments. The diffusive evolution of the concentration field of NSPs on the ER can be described by means of surface partial differential equations (sufPDE). Knodel et al, Viruses 2018, 10, 28 estimated the diffusion coefficient of the NS5a protein by minimizing the discrepancy of an extended set of sufPDE simulations and experimental FRAP time series data. Here, we provide a scaling analysis of the sufPDEs that describe the diffusive evolution of the concentration field of NSPs on the ER. This analysis provides an estimate of the diffusion coefficient that is based only on the ratio of the membrane surface area in the FRAP region and its contour length. The quality of this estimate is explored by comparison to numerical solutions of the sufPDE for a flat geometry and for ten different 3D embedded 2D ER grids that are derived from fluorescence z-stack data of the ER. Finally, we apply the new data analysis to the experimental FRAP time-series data analyzed in our previous paper, and we discuss the opportunities of the new approach.

This experimental research presents an easier model for fitting experimental results that can be simulate the dynamical behaviour of a single degree freedom system, SDFS, subjected in a forced vibration in a shaking table. The fractional damping using a Kelvin-Voigt fractional derivative rheological model, KVFRdm, to represent a fractional oscillator and compare with the experimental model.

In this paper, a class of nonlinear ordinary differential equations with impulses at variable times is considered. The existence and uniqueness of solution are given. At the same time, modifying the classical definitions of continuous dependence and Ga^teaux differentiability, some results on continuous dependence and Ga^teaux differentiable of solution relative to the initial value also are presented in new topology sense. For the autonomous impulsive system, the periodicity of solution is given. As an application, properties of solution for a type of controlled nonlinear ordinary differential equation with impulses at variable times is obtained. These results are foundation to study optimal control problems of systems governed by the differential equations with impulses at variable times.

Tandemly organized rRNA genes are the typical example of a multigene family, where individual members evolve coordinately within but independently between species due to gene conversion and unequal crossing over. More frequently, in eukaryotic species with an inter-species hybrid origin, expression of unhomogenized rRNA genes from one progenitor is epigenetically silenced because of nucleolus dominance, and distinct rRNA genes may lose functionality and evolve faster. Interestingly, we obtained unusual ribosomal gene sequences from Oryza species that showed great diversity and did not appear in the present rice genomic sequence. The diversity of rDNA sequences indicated that the homogenization in rice is incomplete and explains the introgression of distinct rRNA gene families into ancestral rice genome before speciation and continent separation. The divergent large subunit (LSU) ribosomal genes are expressed, some of them differentially, depending on the N-fertilization of plants. Detection of differential transcripts of the rRNA genes suggested that rRNA gene families are not functionally equivalent. Phylogenetic analysis assigned Oryza species branching order to monocots, and monocot lineages probably have the same ecological origin by molecular clock calculation. Therefore, our results suggested that the geographical distances of continents separation cause barriers to the gene flow and homogenization among Oryza species which requires further explanation,

The susceptible-infected-recovered/removed-vaccinated (SIRV) epidemics model is an important generalization of the SIR epidemics model as it accounts quantitatively for the effects of vaccination campaigns on the temporal evolution of epidemics outbreaks. Additional to the time-dependent infection ($a(t)$) and recovery ($\mu (t)$) rates, regulating the transitions between the compartments $S\to I$ and $I\to R$, respectively, the time-dependent vaccination rate $v(t)$ accounts for the transition between the compartments $S\to V$ of susceptible to vaccinated fractions. An accurate analytical approximation is derived for arbitrary and different temporal dependencies of the rates which is valid for all times after the start of the epidemics for which the cumulative fraction of new infections $J(t)\ll 1$. As vaccination campaigns automatically reduce the rate of new infections by transferring susceptible to vaccinated persons, the limit $J(t)\ll 1$ is even better fulfilled than in the SIR-epidemics model. The comparison of the analytical approximation for the temporal dependence of the rate of new infections $\jt(t)=a(t)S(t)I(t)$, the corresponding cumulative fraction $J(t)$, and $V(t)$, respectively, with the exact numerical solution of the SIRV-equations for different illustrative examples proves the accuracy of our approach. The considered illustrative examples include the cases of stationary ratios with a delayed start of vaccinations, and an oscillating ratio of recovery to infection rate with a delayed vaccination at constant rate. The proposed analytical approximation is self-regulating as the final analytical expression for the cumulative fraction $\jinf $ after infinite time allows us to check the validity of the original assumption $J(t)\le \jinf \ll 1$.

The energy-intensive sector of the cement industry needs to find technologically advanced methods to produce cement with as little energy as possible, without polluting the environment and without sacrificing the quality (fineness) of the cement. In addition, the stress on the machines changes the behavior of the data. By combining the k-means method, two (2) feature selection methods, nine (9) machine learning methods, and the differential evolution (DE) method, a dynamic system is created where the user determines the key performance indicators (KPIs) each time. The user has the potential to control the distribution of the data, the input of machine learning models, and the ability to switch the system to the suggested values without damage. The selection of the best-performing models is based on the normalized root mean squared error (NRMSE). The DE method optimizes the dynamic objective function. The optimal values of the manipulated variables are evaluated compared to the value of the objective function from the actual values of the variables. In all experiments, the recommendations are acceptable. The final results show an improvement in the operation of both the cement mill and kiln compared to the current operating condition.

Antiangiogenic therapy (AAT) is an indirect oncological modality which is aimed at disruption of cancer cells nutrient supply. Invasive tumors have been shown to possess inherent resistant to this treatment, while compactly growing benign tumors react to it by shrinkage. It is generally accepted that AAT by itself is not curative. This study presents a mathematical model of non-invasive tumor growth with physiologically justified account of alteration of microvasculature and biomechanical aspects during tumor growth and AAT. In untreated setting the model reproduces tumor growth with saturation, where the maximum tumor volume depends on the level of angiogenesis. The outcomes of simulations of AAT depend on the tumor size at the moment of treatment initiation. If it is close to the stable size of avascular tumor grown in absence of angiogenesis, then the tumor is rapidly stabilized by AAT. Treatment of large tumors is accompanied by displacement of normal tissue due to the tumor shrinkage. During it, microvasculature undergoes distortion which degree depends on the displacement distance. As it affects tumor nutrient supply, the stable size of a tumor that undergoes AAT negatively correlates with its size at the beginning of treatment. For sufficiently large initial tumors, the long-term survival of tumor cells is compromised by competition with normal cells for severely limited inflow of nutrients, which makes AAT effectively curative.

Trichothecene mycotoxin T-2 toxin is an important environmental pollutant and poses a global threat to human and animal health. T-2 toxin could induce nephrotoxicity, however, the precise molecular mechanism remains unclear. In this study, the mice were intraperitoneally administrated with a single dose of 2 mg/kg T-2 toxin. The kidney function and ultrastructural observation were also assessed and found T-2 toxin exposure could cause kidney damage. Transmission electron microscopy showed a significant swelling and vacuolization of the mitochondria of renal cell. A total of 1122, 58, and 391 differential expression genes (DEGs) that were predominantly expressed in kidney tissues at 1 d, 3 d, and 7 d after T-2 toxin exposure, respectively. Early transcriptomic changes at 1 d after exposure were down-regulation of DEGs involved in the cell cycle, p53 signaling pathway, and cellular senescence, while up-regulation of DEGs referred to the ribosome pathway. The temporal variations in gene expression pattern in T-2 toxin exposure in mice kidney were presented and cellular metabolism was disturbed at the exposure recovery period with 7 d. In conclusion, this study, for the first time, provided a comprehensive comparative transcriptomic analysis of gene regulation in T-2 toxin exposure-induced nephrotoxicity at different temporal periods and explored the nephrotoxicity mechanism of T-2 toxin at the mRNA level.

The work is devoted to the development of methods for constructing asymptotic formulas as x→∞ of a fundamental system of solutions of linear differential equations generated by a symmetric two-term differential expression of odd order. The coefficients of the differential expression belong to classes of functions that allow oscillation (for example, those that do not satisfy the classical Titchmarsh-Levitan regularity conditions). As a model equation, the 5th order equation i2p(x)y′′′′′+p(x)y′′′′′+q(x)y=λy, for which various cases of behavior of the coefficients p(x),q(x), is investigated. New asymptotic formulas are obtained for the case when the function h(x)=−1+p−1/2(x)∉L1[1,∞) significantly influences the asymptotics of solutions to the equation. The case when the equation contains a nontrivial bifurcation parameter is studied.

The article outlines a creative approach by fusing ideas from fuzzy contractions, graph mappings, and Kannan mappings to create a brand-new notion known as "Kannan-graph-fuzzy contraction." This combination of concepts makes it possible to create a unique framework for resolving real-world issues controlled by nonlinear models. It is anticipated that using Kannan-graph-fuzzy contractions will offer a fresh approach to discussing solution existence in situations where these ideas overlap. This strategy might have a significant impact on a lot of real-world applications, proving how practical multidisciplinary techniques are for tackling issues in the real world originating from technology and engineering. The article includes several illustrated examples based on computer simulations, making the results more explicit.

In this paper, we obtain the existence and uniqueness theorem for solutions of Caputo type fractional stochastic delay differential systems (FSDDSs) with Poisson jumps by utilizing delayed perturbation of Mittag-Leffler function. Moreover, by using Burkholder-Davis-Gundy's inequality, Doob's martingale inequality and Holder inequality, we prove that the solution of the averaged FSDDSs converges to that of the standard FSDDSs in the sense of Lp. Some known results in the literature are extended.

Every subset S of a Cartesian spaces Rd, endowed with differen- tial structure C∞(S) generated by restrictions to S of functions in C∞(Rd), has a canonical partition M(S) by manifolds, which are or- bits of the family X(S) of all derivations of C∞(S) that generate local one-parameter groups of local diffeomorphisms of S. This partition satisfies the frontier condition, Whitney’s conditions A and B. If M(S) is locally finite, then it satisfies all definitions of stratification of S. This result extends to Hausdorff locally Euclidean differential spaces.

In this work, the analytical treatment of Fourth order pd equations has been discussed with the variational iteration algorithm with an auxiliary parameter. The technique has the capability of reducing the size of computational work and easily overcomes the difficulty of the perturbation method or Adomian polynomials. Comparison with the classic variational iteration algorithm- is carried out, showing that the modification is more efficient and reliable.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

The structural evolution and phase composition of multi-block thermoplastic polyurethanes, with different nature of the soft segments based on poly(butylene adipate) (PBA), were analyzed during in-situ thermal treatments. A combination of synchrotron small- and wide-angle X-ray scattering, differential scanning calorimetry, thermogravimetric analysis, and FTIR spectroscopy was used to determine the influence of macrodiol nature and crystallization conditions on the polymorphic behavior of PBA. Using a new synthesis scheme, a relatively high degree of crystallinity for urethane blocks was achieved, which depends on the diisocyanate type in the structure of the soft segment. The hard segment domains impose geometrical constraints on PBA, thereby altering its crystallization process compared to the neat oligomer. Thus, crystallization after annealing at a low temperature (80 °C) is fast, predominantly yielding a metastable β-phase. When heated to 180 °C, which is higher than the hard-segment melting temperature, a phase-separated structure is observed. Subsequent crystallization is slower, favoring the formation of the stable α-PBA modification. The phase separation can be observed even after the hard block melting. A notably slow crystallization from an isotropic melt was documented after the disruption of phase separation at 230 °C.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Pea (Pisum sativum L.), like most legumes, forms mutualistic symbioses with nodule bacteria and arbuscular mycorrhizal (AM) fungi. The positive effect of inoculation is partially determined by the plant genotype, thus, pea varieties with high and low symbiotic responsivity have been described, but the molecular genetic basis of this trait remains unknown. Here, we compare the symbiotically responsive breeding line ‘Triumph’ of grain pea with its parental cultivars ‘Vendevil’ (a donor of high symbiotic responsivity) and ‘Classic’ (a donor of agriculturally valuable traits) using genome and transcriptome sequencing. We show that ‘Triumph’ inherited one-fourth of its genome from ‘Vendevil’, including the genes related to AM and nodule formation, and reveal that under combined inoculation with nodule bacteria and AM fungi, ‘Triumph’ and ‘Vendevil’, in contrast to ‘Classic’, demonstrate similar up-regulation of the genes related to solute transport, hormonal regulation and flavonoid biosynthesis in their roots. We also identify the gene PsGLP2, whose expression pattern distinguishing ‘Triumph’ and ‘Vendevil’ from ‘Classic’ correlates with difference within the promoter region sequence, making it a promising marker for the symbiotic responsivity trait. The results of the study may be helpful for future molecular breeding programs aimed at creation of symbiotically responsive cultivars of pea.

This article describes the choice of an optimization algorithm for solving problems and the optimal design of an unmanned aerial vehicle propeller. To solve the problem using evolutionary algorithms, it was transformed into an unconstrained optimization problem using a penalty function. The airfoil contours were constructed using a Bezier curve. Design variables were divided into two types: those that describe in general terms the propeller geometry or operation, such as propeller diameter, number of blades, and rev/min; and those that vary with propeller radius, such as chord length, effective airfoil angle, and airfoil geometry. The objective function is the calculation of the propeller power required to achieve a given thrust. The differential evolution algorithm was used to solve this problem.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Partial differential equations (PDEs) are used to describe a wide range of phenomena, such as heat transfer, fluid dynamics, and quantum mechanics. By solving PDEs, we can ob- tain insights into the behavior of the system and make predictions about its future evolution. Conventional numerical methods for obtaining the approximate solutions of PDEs may re- quire extensive computational resources and time, especially for complex PDEs and large- scale problems. The recently developed physics-informed neural network (PINN) has shown promise in a variety of scientific and engineering fields by incorporating physical laws into the loss functions of the neural network (NN). In addition, the training of PINN does not require ground truth data, but it has poor generalization ability to unseen domains. On the other hand, a convolutional neural network (CNN) has fast inference and better generalization ability, but it requires a large amount of training data. Taking the advantages of PINN and CNN by using Legendre multiwavelets (LMWs) as basis functions, we introduce a new method to approach the PDEs in this paper, namely Physics-Informed Legendre Multiwavelets CNN (PiLMWs-CNN), in order to continuously approximate a grid-based state representation that can be handled by a CNN. PiLMWs-CNN enable us to train our models using only physics-informed loss functions without any pre- computed training data, simultaneously providing fast and continuous solutions that gener- alize to previously unknown domains. In particular, the LMWs can simultaneously possess compact support, orthogonality, symmetry, high smoothness, and high approximation order. Compared to orthonormal polynomial (OP) bases, the approximation accuracy can be greatly increased and computation costs can be significantly reduced by using LMWs. We applied PiLMWs-CNN to approximate the damped wave equation, incompressible Navier-Stokes (N- S) equation, and two-dimensional heat conduction equation. The experimental results show that this method provides more accurate, efficient, and fast convergence with better stability when approximating the solution of PDEs.

This paper presents a new low-voltage versatile mixed-mode filter which uses a multi-ple-input/output differential difference transconductance amplifier (MIMO-DDTA). The multi-ple-input of the DDTA is realized using a multiple-input bulk-driven MOS transistor (MI-BD-MOST) technique to maintain a single differential pair, thereby achieving simple structure with minimal power consumption. In a single topology, the proposed filter can provide five standard filtering functions (low-pass, high-pass, band-pass, band-stop, and all-pass) in four modes: voltage (VM), current (CM), transadmittance (TAM), and transimpedance (TIM). This provides the full capability of a mixed mode filter (i.e., twenty filter functions). Moreover, the VM filter offers high-input and low-output impedances and the CM filter offers high-output impedance; therefore, no buffer circuit is needed. The natural frequency of all filtering functions can be electronically controlled by a setting current. The voltage supply is 0.5 V and for a 4 nA setting current, the power consumption of the filter was 281 nW. The filter is suitable for low-frequency biomedical and sensor applications that require extremely low supply voltages and nano-watt power consumption. For the VM low-pass filter, the dynamic range was 58.23 dB @ 1 % total harmonic distortion. The proposed filter was designed and simulated in the Cadence Virtuoso System Design Platform using the 0.18 µm TSMC CMOS technology.

A scientific investigation into visual preferences of rural recreation path landscapes is crucial for enhancing visual qualities and visitors' experience. Taking Baofeng, a representative traditional village in Yunlong, as an example, this study analyzed the visual preference of three typical linear recreational paths with different landscape attributes. We used eye-tracking technology to collect eye movement data and conducted a subjective semantic differential evaluation. Our findings manifest a general inclination amongst individuals to favor closer views and paths with clear trajectories and rich elevation changes while walking, despite preference differences on different types of paths. Regarding group diversity, more inclusive design should be made to meet the sensory needs of different groups. Moreover, despite the limited level of correlation between subjective and objective evaluation methods, combining these two approaches remains indispensable. This synthesis advances prior quantitative landscape evaluation with a specific focus on rural path landscapes and upholds the integrity of results by combining objectivity with subjectivity. It also provides relevant design suggestions for further rural renewal and path planning of Baofeng village.

Despite the successful reconciliation of special relativity and quantum mechanics (QM), a good century ago, general relativity (GR) in its current classical formulation still does not compile with QM. While GR gives precise sensical predictions at large scales, QM is obviously dominated at small scales! We think that the everlasting battle for exploring and understanding the Universe and for privileging a consistent perception of reality is therefore awaiting a consolidator rather than a conqueror. This should be capable of either unifying the two different benchmarks or at least bringing one closer to the other! The latter describes the consolidating approach, which is based on extending QM to relativistic energies and gravitational fields and generalizing Riemann to discretized Finsler geometry. Some properties of the additional geometric structures and curvatures which are disclosed by the proposed quantization and apparently overlooked in Einstein's GR, are analytically and numerically characterized. The analytical analyses introduce dynamics with possible nonlinear connections. We conclude that i) additional geometric structures and curvatures are intrinsic essential and ii) the spacetime at the quantum scale is no longer smooth or continuous. A maximal proper force is predicted, which maximally gravitationally accelerates a test particle and importantly manifests the quantum geometric nature of the generalized spacetime curvature.

Effective sports training should be attuned to the athlete's specific conditionings and characteristics. In motor learning research, two often neglected factors that influence this resonance are the learner's athletic background and the structural diversity of exercises (e.g., relative similarity). This study examines the effects of three learning approaches (i.e., contextual interference (CI), differential learning (DL), and free-play control condition (CO)) on the parallel learning of Handball (HB), Volleyball (VB), and Basketball (BB) skills, considering participants' prior sport backgrounds. Forty-five males (15 HB, 15 VB, and 15 BB players) with a mean age of 22±1.4 years and at least 6 years of experience in the mastered discipline voluntarily participated in this study. A pre-post-retention test design including a 6-week-intervention program was employed. In terms of short-term (pre-post) gain, only the DL- group significantly improved their performance in both non-mastered disciplines (p=0.03 for the BB free-throw and p=0.05 for the HB shooting tests), with a trend (ES=0.53) towards an improvement in the performance of the mastered VB underarm-pass skill. In terms of relatively permanent gains, the CI group significantly improved their performances from pre- to retention-test only in the non-mastered BB free-throw skill (p=0.018). In contrast, the DL group significantly improved their performance at retention compared to the pre-test in both non-mastered BB (p=0.004) and HB (p=0.003) skills, with a trend (ES=0.4) towards improvement in the mastered VB test. In both short, and relatively permanent terms, higher composite score gains were observed in DL compared to CI (p=0.001 and 0.002) and CO (p=0.001 and <0.0001). In conclusion, the present findings provide additional support for the potential advantages of the DL model over those of CI. These findings can serve as the basis for tailored training and intervention strategies and provide a new perspective for addressing various issues related to individual and situational learning.

In this paper, existence and stability results of non-local integro-differential equation with Hilfer derivative of order ω∈(1,2) have been investigated. In this derivative is applied in RLC circuit equation of various fractional order. To proposed problem the existence solutions are derived using Schaefer’s fixed point theorem and the Banach contraction principle is using for uniqueness results. To demonstrate the effectiveness and applicability of our theoretical conclusions and two-step Lagrange polynomial interpolation were used to solve four numerical results.

N-maleimide-derivatized phospholipids are often used to facilitate protein anchoring to membranes. In autophagy studies, this is applied to the covalent binding of Atg8, an autophagy protein, to a phosphatidylethanolamine (PE) in the nascent autophagosome. However, the question remains on how closely the N-maleimide PE derivative (PE-mal) mimicks the native PE in the bilayer. In the present paper, spectroscopic and calorimetric techniques have been applied to vesicles containing either PE or PE-mal (together with other phospholipids) to compare the properties of the native and derivatized forms of PE. According to differential scanning calorimetry, and to infrared spectroscopy, the presence of PE-mal did not perturb the fatty acyl chains in the bilayer. Fluorescence spectroscopy and microscopy showed that PE-mal did not alter bilayer permeability either. However, fluorescence emission polarization of Laurdan and DPH probes indicated an increased order, or decreased fluidity, in the bilayers containing PE-mal. In addition, infrared spectral data from the phospholipid phosphate region revealed a PE-mal-induced conformational change of the polar heads, accompanied by an increased hydration. Globally considered, the results suggest that PE-mal would be a reasonable substitute for PE in model membranes containing reconstituted proteins.

The extent of micro-phase separation in polyurethanes (PUs) depended on the molecular weight, the chemical nature and the structure of the polyol/soft segments. Balanced properties in PUs were obtained by using blends of polyols during synthesis. No previous studies have been devoted to understand the interactions between the soft segments that affect the properties of the PUs. In this study, different blends of two polyols of different nature (polyester – PE - and polycarbonate diol - CD) and similar molecular weight were prepared and their structural, thermal, surface, viscoelastic and self-adhesion properties were assessed. PE showed larger number of structural repeating units and higher number of polar groups than CD, but the carbonate-carbonate interactions in CD were stronger than the ester-ester interactions in PE. The blending of CD and PE imparted synergic structural properties, particularly in the ones containing less than 50 % PE, they were associated to the disrupt of carbonate-carbonate interactions in CD and the formation of new ester-carbonate and hydroxyl-carbonate interactions. Therefore, higher glass transition temperatures, a new diffraction peak at 2θ = 24°, one additional thermal degradation at 426-436 °C, and less steeper decline of the storage moduli to lower temperature were found in CD+PE blends with less than 50 wt.% PE. Furthermore, the different interactions between the polyol chains in the blends were also evidenced on their surface properties, and all CD+PE blends showed self-adhesion property which seemed related to the existence of ester-carbonate and carbonate-carbonate interactions.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

Background: By using outcome prediction scores, it is possible to distinguish between good and poor performers with cochlear implants (CI) after CI implantation. The reasons for poor performance, despite good basic conditions, can be manifold. On the one hand, the postoperative fitting may be inadequate; on the other, neurophysiological disease processes may impair speech understanding with a CI. These disease processes are not yet fully understood. In acoustics, it is known that the auditory brainstem responses (ABR) and their latencies and amplitudes allow differential diagnosis based on reference values for normal-hearing individuals. The aim of this study was to provide reference values for electrically evoked brainstem responses (EABRs) in terms of rate-dependent latencies and amplitudes. Methods: 20 experienced adult CI recipients with a predicted and measured good postoperative word recognition score were recruited from the clinic’s patient pool. In the same stimulation mode and intensity we measured latencies and interpeak-latencies of EABRs and electrically evoked compound action potentials (ECAPs). With a defined supra-threshold stimulation intensity above the individual ECAP threshold, we applied stimulation at several rates between 11 and 91 stimuli per second. Results: We found rate dependences for EABR latency t3 and t5 in the order of 0.19 ms and 0.37 ms respectively, while ECAP was not affected by rate. Correspondingly, the interpeak intervalls’ rate dependences for t5-t1, t5-t3 and t3-t1 were of the order of 0.37 ms, 0.18 ms and 0.19 ms. Comparing the EABR amplitudes between the stimulation rates 11/s and 81/s, we found that at 81/s the amplitudes were significantly reduced down: to 73% for A3 and 81% for A5. These rate dependences of latency and amplitude in EABR have characteristics comparable to those of acoustic ABR. Conclusions: These data may serve to provide reference values for EABR and ECAP latencies, interpeak intervals and amplitudes with respect to stimulation rate. Altered response patterns of ECAPs and EABRs to normalised stimulation modes could be used in the future to describe and classify neuropathological processes in a better-differentiated way.

Key thermophysical properties necessary for the successful design and use of CoCrFeNi alloy in thermophysical applications have been measured experimentally, and the results have been compared with literature values and results previously obtained for commercial Ni-Cr alloys and equiatomic CoCrFeNi alloy. In particular, the thermal diffusivity, coefficient of thermal expansion (CTE), and specific heat capacity were measured for the as-cast and homogenized equiatomic CoCrFeNi alloy over a temperature range allowing the thermal conductivity to be calculated up to 1173 K. The thermal conductivity and thermal diffusivity of the equiatomic CoCrFeNi alloy were found to deviate from monotonic behavior in the temperature range from 773 to 1100 K. Such a deviation was previously observed in the behavior of the temperature dependence of CTE and specific heat capacity of the equiatomic CoCrFeNi alloy. The non-linear behavior is primarily the result of order/disorder phenomena for the as-cast and homogenized sample, as well as additionally for the as-cast sample, non-equilibrium solidification under arc melting conditions. The measured data of thermophysical properties are provided for thermally differently treated samples, and it is shown that there is a difference in the behavior of the temperature dependences of CTE, thermal diffusivity, and heat capacity.

A systematic and comprehensive review of critical applications of Blockchain Technol-ogy with Differential Privacy integration lies within the privacy and security enhancement. This paper aims to highlight the research issues in the e-health domain (e.g., Electronic Medical Rec-ords) and to review the current research directions in Differential Privacy integration with Blockchain Technology.(1) Background: The current state of the art in the e-health domain is identified as follows: (a) healthcare information poses a high level of security and privacy concerns due to its sensitivity; (b) due to vulnerabilities surrounding the healthcare system, a data breach is common and presents a risk for attacks by an adversary; and (c) the current privacy and security apparatus needs further fortification. (2) Methods: The methodology uses a systematic literature review (SLR) to identify and select relevant research papers and academic journals in DP and BT. (3) Results: The results are categorized into: e-Health Record Privacy, Real-Time Health Data, and Health Survey Data Protection to identify inherent issues with Differential Privacy integra-tion with Blockchain and technical challenges.(4) Conclusion: This review thoroughly surveyed and summarized Differential Privacy mechanisms in EMR privacy, real-time health data, and health survey data protection while highlighting challenges.

The differential-equation of second order for space-time oscillation in flat tangential-spacetime of Minkowski-type can be written as an energy-equation. For this energy-equation the analogon of damping energy in two coupled Minkoswki-spacetimes with ftl can be calculated and formulated over Lamberts W-function or via Euler-equation.

In this study, a design of Morlet wavelet neural networks (MWNNs) is presented to solve the prediction differential model (PDM) using the global approximation capability of genetic algorithm (GA) and local quick interior-point algorithm scheme (IPAS), i.e., MWNN-GAIPAS. The famous PDM is known as a variant of functional differential system that works as an opposite of the historical delay differential models. A fitness function is optimized using the mean square error by applying the GA-IPAS for solving the PDM. Three PDM examples have been presented numerically to check the authenticity of the MWNN-GAIPAS. For the perfection of the designed MWNN-GAIPAS, the comparability of the obtained results and exact results is performed. Moreover, the neuron analysis is performed by taking the 3, 10 and 20 number of neurons. The statistical observations have been performed to authenticate the reliability of the MWNN-GAIPAS for solving the PDM.

We discuss a remote sensing system that is used to simultaneously detect range-resolved differential absorption LIDAR (light detection and ranging; DIAL) signals and integrated path DIAL signals (IP-DIAL) from aerosol targets for ranges up to 22 km. The DIAL/IP-DIAL frequency converter consists of an OPO pumped at 1064 nm to produce light at 1.6 μm and operates at 100 Hz pulse repetition frequency. The probe light is free space coupled to a movable platform that contains one transmitter and two receiver telescopes. Hybrid photon counting/current systems increase the dynamic range for detection by two orders of magnitude. Range resolved and column integrated dry-air CO2 and CH4 mixing ratios are obtained from line shape fits of CO2 and CH4 centered at 1602.2 nm and 1645.5 nm, respectively and measured at 10 different frequencies over ≈ 1.5 cm-1 bandwidth. The signal-to-noise ratios (SNR) of the IP-DIAL returns from cloud aerosols approach 1000:1 and the uncertainties in the mixing ratios weighted according to the integrated counts over the cloud segments range from 0.1 % to 1 %. The range averaged DIAL mixing ratios are in good agreement with the IP-DIAL mixing ratios at the 1 % to 2 % level for both CO2 and CH4. These results can serve as a validation method for future active and passive satellite observational systems.

In recent years, applying deep learning to solve physics problems has attracted much attention. Data-driven deep learning methods produce operators that can learn solutions to the whole system of partial differential equations. However, the existing methods are only evaluated on simple flow equations (e.g., Burger's equation), and only consider the generalization ability on different initial conditions. In this paper, we construct CFDBench, a benchmark with four classic problems in computational fluid dynamics (CFD): lid-driven cavity flow, laminar boundary layer flow in circular tubes, dam flows through the steps, and periodic Karman vortex street. Each flow problem includes data with various boundary conditions, fluid physical properties, and domain geometries. Compared to existing datasets, the advantages of CFDBench are (1) comprehensive. It contains common physical parameters such as velocity, pressure, and cavity fraction. (2) realistic. It is very suitable for deep learning solutions of fluid mechanics equations. (3) challenging. It has a certain learning difficulty, prompting to find models with strong learning ability. (4) standardized. CFDBench facilitates a comprehensive and fair comparison of different deep learning methods for CFD. We make appropriate modifications to popular deep neural networks to apply them to CFDBench and enable the accommodation of more changing inputs. The evaluation on CFDBench reveals some new shortcomings of existing works and we propose possible directions for solving such problems.

Background: Ultrasonography (US) represents the gold standard imaging method for the assessment of testicular lesions (TL). The gray-scale (GSUS) and color-Doppler (CDUS) ultrasound examination allow sonographers to investigate size, margins, echotexture and vascular features of TL, with the effort to differentiate benign from malignant lesions. Recently, the use of contrast-enhanced US (CEUS) and sonoelastography (SE) led to further improvements in the differential diagnosis of TL. Although GSUS and CDUS are often sufficient to suggest the benign or malignant nature of TL, CEUS can be decisive in the differential diagnosis of unclear findings, while SE can help to strengthen the diagnosis. The contemporary combination of GSUS, CDUS, CEUS and SE led to a new diagnostic paradigm named multiparametric US (mp-US), able to provide a more detailed characterization of TL than the single techniques alone. This narrative and pictorial review is aimed to describe the mp-US appearance of several TL. Methods: An extensive Medline search was performed identifying studies in the English language focusing on mp-US evaluation of TL. Results: a practical mp-US “identity card” and iconographic characterization of several benign and malignant TL is provided herein. Conclusions: the mp-US characterization of TL reported herein can be useful in daily clinical practice.

The main object of this work is to establish the existence and uniqueness of a solution to the 3D Navier-Stokes (NS) system for an incompressible fluid with viscosity. The nonlinearity of the NS system, as well as the need to estimate velocity and pressure for every value of the viscosity parameter [1] make them challenging to solve. In this regard, in the present work, we study the Navier-Stokes system, which describe the flow of a viscous incompressible fluid and the solution was obtained for velocity and pressure in an analytical form. In addition, the found pressure distribution law, which is described by a Poisson type equation and plays a fundamental role in the theory of Navier-Stokes systems in constructing analytic smooth (conditionally smooth) solutions.

The National Institute of Justice reported that current methods for processing sexual assault samples have a high failure rate, with 60 to 80 percent of tested kits unable to produce usable DNA profiles. Even when samples test positive for male DNA, 34 percent of sexual assault kits (SAK) do not yield recovered male DNA after differential extraction. Less than 30% recovery of available sperm DNA contributes to this low success rate. The SpermX™ method (SX) has been shown to recover 80 percent or more of sperm DNA from sexual assault samples. An interlaboratory evaluation compared SX to standard differential extraction (DE) protocols. Mock samples with known ratios of female epithelial cells and sperm cells were processed using both methods. Results revealed that SX consistently provided CODIS up-loadable DNA profiles, even with as few as 25 sperm cells, whereas DE failed to produce usable results. On average, SX yielded a seven-fold increase in the recovery of unshared male alleles compared to DE. In conclusion, SX outperformed DE in recovering higher quantities of male DNA with minimal female carryover in sexual assault-type samples. This improved success rate in obtaining usable DNA profiles can significantly aid in solving sexual assault cases. Keywords: Differential extraction, Sexual Assault Kit (SAK), Sperm DNA, STRmix™, Combined DNA Index System (CODIS), Forensic DNA analysis, Low Sperm Samples, DNA Mixtures, Autosomal STR Analysis, SpermX.

The global prevalence of type 2 diabetes mellitus (T2DM) has surged in recent decades and the identification of differential glycemic responders can aid tailored treatment for prevention of pre-diabetes and T2DM. A mixed meal tolerance test (MMTT) based on regular foods offers potential to uncover differential responders in dynamical postprandial events. We aimed to fit a simple mathematical model on dynamic postprandial glucose data from repeated MMTTs among partic-ipants with elevated T2DM risk, to identify response clusters and investigate their association with T2DM risk factors and gut microbiota. Data were used from a 12-week multi-center dietary inter-vention trial involving high-risk T2DM adults, comparing high- versus low-glycemic index foods within a Mediterranean diet context (MEDGICarb). Model-based analysis of MMTTs from 155 participants (81 females, 74 males) revealed two distinct plasma glucose response clusters that were associated with baseline gut microbiota. Cluster A, inversely associated with HbA1c and waist circumference and directly with insulin sensitivity, exhibited a contrasting profile to cluster B. Findings imply that a standardized breakfast MMTT using regular foods could effectively distin-guish non-diabetic individuals at varying risk levels for T2DM using a simple mechanistic model.

The fractional diffusion equations with integrals play a significant role in describing anomalous diffusion phenomena. We first construct an appropriate resolvent family, and use the convolution theorem of Laplace transform, the probability density function, Cauchy integral formula and Fubini theorem to study its related equicontinuity, strongly continuity, compactness, etc. Then, a reasonable mild solution is defined. Finally, by combining some fixed point theorems, we obtain some conclusions on the existence and uniqueness of mild solutions.

This work aims to introduce a novel concept: the Riesz-Dunkl fractional derivatives, within the context of Dunkl type operators. A particularly noteworthy revelation is that when a specific parameter $\kappa$ equals zero, the Riesz-Dunkl fractional derivative smoothly reduces to both the well-known Riesz fractional derivative and the fractional second-order derivative. Furthermore, we introduce a new concept: the fractional Sobolev space. This space is defined and characterized using the versatile framework of the Dunkl transform.

In order to solve the problems of complicated steering control of unmanned vehicles in the field and difficult steering on complex roads, we designed a wheel-track composite vehicle equipped with a novel power differential steering mechanism with dual driving, which drove the steering of the vehicle through the differential rotation of the rear two wheels. The unmanned vehicle was simple to control, small in size, and able to work under the conditions of complex roads, such as hills, mountains, and muddy land. Firstly, a steering mechanism with both differential speed and force was designed to prevent the vehicle from skidding into muddy land and stopping motionless. Secondly, the kinematics model and dynamics model of the two drive shafts and the two output shafts (wheel shafts) were established. Thirdly, according to the relationship between the rotational speed of the two output shafts and the steering radius of the vehicle, the kinematic model of the rotational speed of the two input shafts and the steering radius of the wheel-track composite vehicle was obtained. Finally, according to the test data, the mathematical model of rotational speeds of the two input shafts and the actual steering radius of the vehicle was obtained by neural network fitting, and the maximum relative error between the model results and the actual steering radius value was 3.53%. The combination of power differential steering mechanism and wheel-track composite unmanned vehicle increased the adhesion with the ground and could better adapt to the complex road environment. In conclusion, the unmanned vehicle had the advantages of continuous radius steering, deceleration and torsion increase, differential lock, etc. It was suitable for all-terrain military and civilian vehicles and various special equipment mobile platforms of the walking device, and the research results could provide theoretical references for the steering control and structural optimization of the wheel-track composite vehicle under the environment of complex road surface.

TmMgB5O10 spontaneous crystals were synthesized via flux-growth technique from a K2Mo3O10-based solvent. The crystal structure of the compound was solved and refined within the space group P21/n. The first principles calculations of the electronic structure reveal that TmMg-pentaborate is an insulator with an indirect energy band gap of approximately 6.37 eV. Differential scanning calorimetry measurements and powder X-ray diffraction studies of heat-treated solids show that TmMgB5O10 is an incongruent melting compound. A characteristic band of Tm3+ cation corresponding to the 3H6 → 1D2 transition is observed in the photoluminescence excitation spectra of TmMg-borate. The as-obtained crystals exhibit intense blue emission with the emission peaks centered at 455, 479, 667 and 753 nm. The most intensive band corresponds to the 1D2 3F4 transition.

In this paper, we derive Jeffreys divergence, generalized Fisher divergence and corresponding De Bruijn identities on space-time random field. First, we determine the relation between Fisher information on the space-time random field in one of the space-time points and the ratio of Jeffreys divergence on a space-time random field at distinct space-time positions to the square of coordinate difference. In addition, we also find identities between the partial derivative of the Jeffreys divergence and the generalized Fisher divergence with respect to space-time variables, i.e. the De Bruijn identities, between two space-time random fields obtained by different parameters under the same Fokker-Planck equations. At the end of this paper, we present three examples of the Fokker-Planck equations on space-time random fields, identify their density functions, and derive the Jeffreys divergence, generalized Fisher information, generalized Fisher divergence, and accompanying De Bruijn identities.

In this paper, we consider a pursuit-evasion game of inertial players, where pursuer’s control is subject to integral constraint, and evader’s control is subject to geometric constraint. In the pursuit problem, the main tool is the strategy of parallel pursuit. Sufficient conditions are obtained for the solvability of pursuit-evasion problems. Also, the main lemma describing the monotonicity of an attainability domain of the evader is proved and an explicit analytical formula for this domain is given. As one of the important results of our paper, the Isaacs Life-line game is solved for a special case.

The paper examines rational Darboux-Crum transforms (RDCTs) of the Jacobi-reference (JRef) potential on the line, with an emphasis on the transformations using only normalizable seed solutions. The Cooper-Ginocchio-Khare (CGK) potential constitutes the simplest example of this rich family of exactly solvable one-dimensional (1D) potentials. It was explicitly confirmed that that an arbitrary Darboux-Crum transformation (DCT) of the given Sturm-Liouville equation (SLE) can be represented as a chain of sequential Darboux deformations of the associated Liouville potentials. If the rational SLE (RSLE) under consideration is exactly solvable and the transformation function (TF) used at each step is nodeless then each RSLE constructed in such a way was proven being exactly solvable itself. The exact solvability of RDCTs of the JRef canonical SLE (CSLE) was also confirmed for the DCTs using pairs of juxtaposed eigenfunctions (an extension of the renowned Adler theorem to the RCSLEs of our interest). By re-expressing the reference polynomial fraction (RefPF) of the transformed CSLE in terms of the Krein determinant (KD), instead of Crum Wronskian (CW), it was shown that the eigenfunctions under consideration are expressible in terms of polynomial solutions of a generalized Heun equation with positions of the most poles dependent on the exponent parameters. The outlined technique was extended to two isospectral SUSY partners of the JRef potential (as well as to its third sibling with the inserted new lowest-energy level) which, by analogy with the CGK potential, are quantized by polynomial solutions of the 2-Heun equation with all four poles at some fixed positions on the real axis.

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

The present work focuses on developing miniaturized, light weight electrochemical sensors for detection of chemical warfare agents (CWAs) like sarin and tabun simulants, i.e., diisopropyl fluorophosphate (DFP), and O,S-diethyl methyl phosphonothioate (O,S-DEMPT). Differential pulse voltammetry (DPV) was employed to examine the redox properties of capturing molecular probe CE2 with the nerve agent stimulants. Coupling of a portable potentiostat with the drone technology could allow on-situ and remote detection of analytes such CWAs to be realized, which can be crucially important to the national and global securities.

Frontal Temporal Dementia (FTD) is a neurological disorder known to have less therapeutic options. So far only a few biomarkers are available for FTD that can be used as potential comorbidity targets. To this end, in the present study we aim to identify potential biomarkers or susceptible genes for FTD that show comorbidities with diseases such as COVID-19 and Breast Cancer. Gene expression Omnibus datasets containing FTD expression profiles from African American and white ethnicity background were included in our study. In FTD samples of GSE193391 dataset, we identified 305 DEGs with 168 genes being up-regulated and 137 genes being down-regulated. We conducted comorbidity analysis for COVID-19 and Breast cancer followed by analysis of potential drug interactions, pathogenicity, analysis of genetic variants and functional enrichment analysis. Resulting genes AKT3, GFAP, ADCYAP1R1, VDAC1, and C4A showed significant transcriptomic alterations in FTD and significant comorbidity status with COVID-19 and Breast cancer. Functional pathway analysis revealed that these comorbid genes were significantly enriched in the pathways such as glioma, JAK/STAT signaling, systematic lupus erythematosus, neurodegeneration-multiple diseases and neuroactive ligand-receptor interaction. Overall, from these results, we concluded that these genes could be recommended as potential therapeutic targets for the treatment of comorbidities in FTD.

A patient in her early 20s presented with constant and progressive lower abdominal and back pain, mainly on the right side of the abdomen, purulent vaginal discharge and pyrexia. Radio-logical assessment revealed a possible tuboovarian abscess and incidental diagnosis of ipsilateral renal agenesis. The patient was treated for pelvic inflammatory disease (PID), however after antibiotic administration and since the symptoms were not resolving, an abdominal MRI was requested which revealed a uterus didelphys with two cervices, an obstructed haemivagina and evidence of haematocolpos. The diagnosis of OHVIRA syndrome was confirmed and the patient underwent an excision of the vaginal septum, drainage of the haematopyocolpos and laparoscopic drainage of the tuboovarian abscess. She achieved a good recovery.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

This work assesses the dietary use of two insect meals of Tenebrio molitor (TM) larvae reared in conventional (TM-10) or MAPs-enriched substrates (MAP-TM-10) as fish meal replacements (10%) in the diets of gilthead seabream (Sparus aurata). Fish (n=4,500; 207.19 ± 1.47 g) were divided into three groups with triplicates: Control (fed conventional diet), TM-10 and MAP-TM-10 groups.The fish were reared in floating cages for 12 weeks and The dietary effects on white blood cell ac-tivation, heat shock proteins, MAPKs, and apoptosis of the fish were evaluated. The MAP-TM-10 group exhibited the highest eosinophilic induction and plasma cells. Phosphorylated levels of p38 MAPK; p44/42 MAPK; HSP70 and HSP90 increased in the TM-10 and MAP-TM-10. In terms of apoptosis, Bax levels were lower in the TM groups compared to the Control, and the MAP-TM-10 group showed even lower levels than the TM-10 group. Bcl-2 levels increased in the TM-10 compared to the Control, and further increased in the MAP-TM-10 group. The Bax/Bcl-2 ratio, an apoptosis indicator, decreased in the TM groups, with the MAP-TM-10 group showing a further decrease compared to TM-10. These findings suggest that insects breeding substrate enriched with MAPs modulated the effect of TM on cellular stress and apoptosis.

This paper presents a numerical method for solving a two-dimensional subdiffusion equation with a Caputo fractional derivative. The problem considered assumes symmetry in both the equation’s solution domain and the boundary conditions, allowing for a reduction of the two-dimensional equation to a one-dimensional one. The proposed method is an extension of the fractional Crank-Nicolson method, based on the discretization of the equivalent integral-differential equation. To validate the method, the obtained results were compared with a solution obtained through Laplace transform. The analytical solution in the image of the Laplace transform was inverted using the Gaver-Wynn-Rho algorithm implemented in the specialized mathematical computing environment, Wolfram Mathematica. The results clearly show the mutual convergence of the solutions obtained by the two methods.

The core reasoning task for datalog engines is materialization, the evaluation of a datalog program over a database alongside its phys- ical incorporation into the database itself. The de-facto method of computing it, is through the recursive application of inference rules. Due to it being a costly operation, it is a must for datalog engines to provide incremental materialization, that is, to adjust the computation to new data, instead of restarting from scratch. One of the major caveats, is that deleting data is notoriously more involved than adding, since one has to take into account all possible data that has been entailed from what is being deleted. Differential Dataflow is a computational model that provides efficient incremen- tal maintenance, notoriously with equal performance between ad- ditions and deletions, and work distribution, of iterative dataflows. In this paper we investigate the performance of materialization with three reference datalog implementations, out of which one is built on top of a lightweight relational engine, and the two others are differential-dataflow and non-differential versions of the same rewrite algorithm, with the same optimizations.

The structure and phenomena arising from charge transfer in cold field emission modus in a single closed carbon nanotube under cold field emission conditions were studied. By studying microphotographs in various microscopes - AFM, SEM, TEM it was found inhomogeneities in the form of two types of superlattices. The conductivity of the emitter section of a nanodiode circuit with an emitter made of an individual closed carbon nanotube (CNT) and arrays of closed CNTs was studied. High values of cold field emission were observed, as well as nonlinearity and anomalies of the current-voltage characteristic (I-V characteristics), which manifested themselves in the form of peaks at low and high current values. Peaks in the CVC have distinct areas of negative differential conductivity. It is argued, that the anomalously high currents in the I–V characteristics of cold field emission of electrons from a nanoemitter made of closed CNTs can be associated with a sharp increase in the density of electron states at energies near the van Hove singularity.

For a linear ordinary differential equation (ODE in short) of the third order, results are presented that supplement the theory of conjugate points and extremal solutions by W. Leighton, Z. Nehari, M. Hanan. It is especially noted the sensitivity of solutions to the initial data, which makes their numerical study difficult. Similar results were obtained for the third-order nonlinear equations of the Emden-Fowler type.

A diagnosis of typical chronic lymphocytic leukemia (CLL) requires the presence of ≥5000 clonal B-lymphocytes/μL with the coexistence of CD19, CD20, CD5, and CD23 and the restriction of light chain immunoglobulin, and the lack of expression of antigens CD22 and CD79b. Atypical CLL (aCLL) can be distinguished from typical CLL morphologically and immunophenotypically. Atypical CLL cells are defined as prolymphocytes; morphologically, these present as deeply-clefted lymphocytes which are larger than those in typical CLL, with condensed chromatin and without prominent nucleoli. However, current aCLL diagnostics rely more on immunophenotypic characteristics rather than atypical morphology. Immunophenotypically, atypical CLL differs from classic CLL in the lack of expression of one or fewer surface antigens, most commonly CD5 and CD23, and the patient does not meet the criteria for a diagnosis of any other B-cell lymphoid malignancy. Morphologically atypical CLL has more aggressive clinical behavior and worse prognosis than classic CLL. Patients with aCLL are more likely to display markers associated with poor prognosis, including trisomy 12, unmutated IGVH, and CD38 expression compared with classic CLL. However, no standard or commonly-accepted criteria exist for differentiating aCLL from classic CLL and the clinical significance of aCLL is still under debate. This review summarizes the current state of knowledge on the morphological, immunophenotypic and genetic abnormalities of aCLL.

The theory of fractional calculus extends the order of classical integer calculus from integer to non-integer. As a new engineering application tool, it has made many important research achievements in many fields, including image processing. This paper mainly studies the application of fractional calculus theory in image enhancement and denoising, including the basic theory of fractional calculus and its amplitude frequency characteristics, the application of fractional differential operator in image enhancement, and the application of fractional integral operator in image denoising. The experimental results show that the fractional calculus theory has more special advantages in image enhancement and denoising. Compared with the existing integer order image enhancement operators, the fractional differential operator can more effectively enhance the "weak edge" and "strong texture" details of the image. The fractional order integral image denoising operator can not only improve the signal-to-noise ratio of the image compared to traditional denoising methods, but also better preserve detailed information such as edges and textures of the image.

An approach of implementing X-bar and R control charts as a statistical control tool to monitor changes in the melting profile of fresh and stored flaxseed oils by differential scanning calorimetry (DSC) was used. Phase transition melting profiles were collected after 0, 2, 4, 6 months of storing flaxseed oils, originated from five different cultivars. Four peaks at around -36, -30, -25, -12 °C were identified using the deconvolution analysis procedure, which enabled data to be collected on peak temperature (T), peak height (h) and the peak area (A), as well as the ratio calculated from these parameters. Control charts of DSC parameters, linked to the second peak (h2, A2) and calculated ratios of those parameters showed an increasing or decreasing trend within the storage time, thus were considered to be indicators of oil deterioration. Since DSC parameters related to the first peak (h1, A1) and third peak (h3, A3) remained unchanged within storage, they were established as the markers of flaxseed oil authenticity.

Alzheimer’s disease (AD) is the leading cause of dementia, characterised by beta-amyloid plaques, neurofibrillary tangles, and oxidative stress. Iron is suspected to enhance disease progression, and chelation may be a potential treatment. We propose that Aloysia citrodora Paláu (AC), a plant in the Verbenaceae family, can act as a moderate chelator of iron. It may reduce the effect of iron on beta-amyloid 1-42 (Aβ1-42) aggregation. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to demonstrate that AC can interact with iron (II) and iron (III), the two most abundant forms of iron within the body. DPV was also used to characterise Aβ1-42 aggregation, and two main features were obtained. The first is the tyrosine peak (~0.6 V) decreased in magnitude over time, which is a sign of aggregation and folding. The other is a conglomerate of peaks at ~0 V, whose identity is unknown. Furthermore, iron (II) increased the rate of tyrosine peak depreciation, and the addition of AC negated this induced effect. This implied that iron (II) increases Aβ1-42 aggregation into higher order, and AC may be an effective countermeasure.

This paper delves into the dynamics of asset pricing within Bachelier’s market model (BMM), elucidating the representation of risky asset price dynamics and the definition of riskless assets. It highlights the fundamental differences between BMM and the Black-Scholes-Merton market model (BSMMM), including the extension of BMM to handle assets yielding a simple dividend. Our investigation further explores Bachelier’s term structure of interest rates (BTSIR), introducing a novel version of Bachelier’s Heath-Jarrow-Morton model and adapting the Hull-White interest rate model to fit BMM. The study concludes by examining the applicability of BMM in real-world scenarios, such as those involving environmental, social, and governance (ESG)-adjusted stock prices and commodity spreads.

Ditching-rotary tiller was widely used in tillage and ditching furrow during rapeseed sowing. As its ditching furrow system (consist of four identical ditching plows) would bear great drag resistance from the soil during operation, the ditching plow was optimized based on differential geometry analysis and EDEM simulation. Resistance-velocity simulation indicated the plow with parabolic type guide curve had better reduce-drag characteristics. Differential geometry analysis indicated decay rate of E and growth rate of G could represent the variable regularity of drag resistance with the increase of velocity. The L value could represent the magnitude of drag resistance. The smaller L value, decay rate of E and growth rate of G, the better drag-reduce characteristics. Quadratic rotation orthogonal combination design shown the optimal structural parameter values were: Δθ=15°, θmin=45°, h=250mm, l=100mm. The minimum average drag resistance was 230.1N. The differential geometry analysis of optimal ditching plow shown |dE/dκ| and |dG/dκ| could obtain minimum value, indicating growth rate of drag resistance for optimal plow was the lowest within the experimental level. Field experiment indicated the operation effect of optimized ditching furrow system could met the requirements of rapeseed sowing. The research provided in-depth theoretical guidance for Drag-reduce design of plow.

A new green-validated and highly sensitive electrochemical method for the determination of molnupiavir (MOV) has been developed using cyclic voltammetry. The proposed analytical platform involves the use of disposable screen-printed reduced graphene oxide 2.5% electrode (SPrGOE 2.5%) for the first time to measure MOV with high specificity. The surface morphology of the sensor was investigated by using a scanning electron microscope armed with an energy-dispersive X-ray probe. The fabricated sensor attains improved sensitivity when sodium dodecyl sulfate (SDS) surfactant was added to the supporting electrolyte solution. Thus, various factors were investigated in order to select the best supporting electrolyte for voltammetric determination of MOV, and the optimum conditions were achieved by employing 0.04 M Britton-Robinson at pH 2, 10-4 M SDS, and SPrGOE 2.5%. Well-defined MOV oxidation peaks were obtained with no reduction peaks in cyclic voltammetry using diffusion-controlled pathways. The method was validated using differential pulse voltammetry according to ICH guidelines, providing it to be precise, accurate, specific, and robust with linearity over a concentration range of 50-6017 ng/mL. The incorporation of the reduced graphene nanoparticles supported the in situ interaction between electrode surface and MOV, improved the selectivity, and reduced the detection limit to the concentration level of 15.98 ng/mL. The stability investigation demonstrated that SPrGOE 2.5% can provide high-stability behavior throughout a three-month period under refrigeration. The fabricated SPrGOE 2.5% was successfully employed for the measurement of MOV in pharmaceutical capsules and human bio-fluids without the interference of endogenous matrix components as well as the commonly used excipient.

The (numerical) solution of Ordinary Differential Equations (ODEs) problems is of paramount relevance, ODEs system being an ubiquitous mathematical formulation of many physical phenomena (such as those involved in fluid dynamics, chemistry, biology, evolutionary-anthropology, ...): almost every dynamici phenomenon can be modeled by means of an ODEs system. The present paper is the first manifesto of FOODIE, a library aimed to numerically solve ODEs problems by means of a clear, concise and efficient abstract interface. FOODIE, meaning Fortran Object oriented Ordinary Differential Equations integration library, has manifolds aims: to provide a set to built-in numerical schemes that are accurate, robust, validated and efficient and to allow easy application of these schemes to (almost) all ODEs problems by means of an effective Abstract Calculus Pattern. The key idea is to allow the same solver-implementation to be applied to all ODEs problems thus avoiding the re-implementation of the ODEs solver for each different ODEs problem: code re-usability is consequently maximized, FOODIE being a general robust framework. Besides, the same framework also allows rapid development of new ODEs solvers due to the high abstraction level of the library itself. The present paper is the first announcement of FOODIE project: the current implementation is extensively discussed and its capabilities are proved by means of tests and examples.

In this paper, we report orthogonal fuzzy versions of some celebrated iterative mappings. We provide various concrete conditions on the real valued functions J,S:(0,1]→(−∞,∞) for the existence of fixed-points of (J,S)-fuzzy iterative mappings. We obtain many fixed point theorems in orthogonal fuzzy metric spaces. We apply (J,S)-fuzzy version of Banach fixed point theorem to show the existence and uniqueness of the solution. We support these results with several non-trivial examples and applications to Volterra-type integral equations and fractional differential equations.

The dynamics of the main photosynthetic structures is studied by mathematical modeling methods in this article. Chlorophyll portion variability in phytoplankton and the formation of energy-intensive substances in the process of photosynthesis underlie the models. These cellular components are considered in terms of their participation in the growth of specific biomass. Computational experiments are presented that simulate various degrees of environmental friendliness. The corresponding functions are built in accordance with seasonal fluctuations throughout the year in the Far East region of Russia. The stability of model solutions in long-term dynamics is also investigated. The models were tested for biological adequacy and their effectiveness was compared. For the model selected as a result of the comparison, the optimal control problem has been formulated and solved. It is shown that in this way it is possible to reduce the space of the initial components of the model system.

Discrete distribution estimation is a fundamental statistical tool, which is widely used to perform data analysis tasks in various applications involving sensitive personal information. Due to privacy concerns, individuals may not always provide their raw information, which leads to unpredictable biases in the final results of estimated distribution. Local Differential Privacy (LDP) is an advanced technique for privacy protection of discrete distribution estimation. Currently, typical LDP mechanisms provide same protection for all items in the domain, which imposes unnecessary perturbation on less sensitive items and thus degrades the utility of final results. Although, several recent works try to alleviate this problem, the utility can be further improved. In this paper, we propose a novel notion called Item-Oriented Personalized LDP (IPLDP), which independently perturbs different items with different privacy budgets to achieve personalized privacy protection. Furthermore, to satisfy IPLDP, we propose the Item-Oriented Personalized Randomized Response (IPRR) based on the observation that the sensitivity of data shows an inverse relationship with the population size of respective individuals. Theoretical analysis and experimental results demonstrate that our method can provide fine-grained privacy protection and improve data utility simultaneously.

For a system that turns out to be inactive in time t, the past entropy is considered as an uncertainty measure for the past lifetime distribution. In this study, we consider a coherent system that includes n components and has the property that all the components of the system have failed at time t. To assess the predictability of the coherent system’s lifetime, we use the system’s signature to determine the Rényi entropy of its past lifetime. We study several analytical results, including expressions, bounds, and order properties for this measure.

A wide variety of renal neoplasms can have cystic areas. It happens for different reasons: some tumors have an intrinsic cystic architecture, others have a pseudocystic degeneration of necrotic foci or they have cystically dilated renal tubules constrained by stromal neoplastic cells. Clear cell renal cell carcinoma (CCRCC), either solid or cystic, is the most frequent type of renal cancer. While pseudocysts are found in high-grade aggressive CCRCC, cystic growth is associated to low-grade indolent cases. The latter also form through a cyst-dependent molecular pathway and they are more frequent in patients suffering from VHL disease. The differential diagnosis with multilocular cystic renal neoplasm of low malignant potential and clear cell papillary renal cell tumor can be especially hard and it requires a focused macroscopical and microscopical pathological analysis. As every class of renal tumors include cystic forms, a knowledge of criteria for a differential diagnosis is mandatory.

This paper is concerned with variational methods for open quantum systems with Markovian dynamics governed by Hudson-Parthasarathy quantum stochastic differential equations. These QSDEs are driven by quantum Wiener processes of the external bosonic fields and are specified by the system Hamiltonian and system-field coupling operators. We consider the system response to perturbations in these operators and introduce a transverse Hamiltonian which encodes the propagation of the perturbations through the unitary system-field evolution. This approach provides an infinitesimal perturbation analysis tool which can be used for the development of optimality conditions in quantum control and filtering problems. Such settings employ, as performance criteria, quadratic (or more complicated) cost functionals of the system and field variables to be minimised over the energy and coupling parameters of system interconnections. We demonstrate an application of the transverse Hamiltonian variational approach to a mean square optimal coherent quantum filtering problem for a measurement-free field-mediated cascade connection of a quantum system with a quantum observer.