The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

The ductile behavior of strain hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions for applications where high energy dissipation is needed, such as earthquake, impact by a projectile, or blast. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily entail compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading, relevant to the mentioned high-speed loading scenarios, the paper at hand studies the performance of a SHCC and its constituent cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under the quasi-static and impact loading conditions, which was necessary for a reliable comparison of the obtained compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s-1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled performing impact shear experiments on planar specimens using the tensile wave generated in the SHTB. Results showed a dynamic increase factor (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC yielded the higher shear strength than the non-reinforced matrix.

Bodybuilders utilize peaking strategies in a bid to fine-tune their aesthetics for competition day. The most prevalent peaking strategies utilized by natural bodybuilders are unreported in the current literature. Eighty-one (M - 59, F - 22) natural bodybuilders were recruited from competitions during the 2016 and 2017 British Natural Bodybuilder Federation seasons. Competitors completed a 34-item questionnaire designed to investigate peaking and contest day strategies. The questionnaire listed commonly utilized peaking strategies and provided additional space for qualitative information. Analysis of the data indicated that carbohydrate (CHO), water and sodium manipulation were the most commonly utilized peak week strategies. The consumption of high glycemic index CHO was the most common competition day strategy. Only 6.2 % of competitors reported following their regular diet the week prior to competition. The CHO manipulation strategies were similar to classical CHO loading, whereby bodybuilders attempt to maximize muscle glycogen concentrations. Furthermore, bodybuilders attempted to remove superfluous water by exploiting the diuretic/polyuria effect associated with water loading/restriction. The potentially deleterious effects of peaking on bodybuilders' health is considered and the efficacy of these strategies to enhance appearance is discussed. The findings of the present investigation are likely to be of interest to bodybuilders and their coaches.

This paper introduces a structured design for an effective power-sharing technique among converter-interfaced distributed generation (DG) units within a microgrid that operates without a synchronous generator. The proposed power-sharing technique leverages the battery energy storage system (BESS) to promptly respond to network changes. The real power output of each commercial distributed energy resources (CDER) unit is governed by a frequency-droop characteristic and a complementary frequency restoration strategy. Deloading techniques are employed by solar and wind power generators to enhance response during power supply or demand disturbances. To ensure microgrid stability, small-signal analysis is conducted for controller design, including the determination of stability margins. Initial tuning of the power-sharing technique parameters is achieved using the Ziegler-Nichols Method, followed by further optimization through a meta-heuristical algorithm to enhance the response time of energy sources. The proposed power-sharing technique's performance is evaluated on a benchmark medium voltage network using industry-standard commercial software. The test results demonstrate the precise and rapid power-sharing capabilities among DGs facilitated by the proposed technique, highlighting its effectiveness in dynamic microgrid environments.

Brick is widely used in construction, but it often becomes debris due to its use and lack of quality. In Ecuador, brick production is not completely industrialized, resulting in deficient properties for construction. In the city of Loja, most bricks come from artisanal factories . This research proposes the use of geopolymerization and waste bricks to create a sustainable material in construction. Geopolymerization processes were employed with sodium hydroxide as the alkaline activator. The resulting products underwent various tests to obtain the optimal formula in terms of material behavior and strength. Physical and mechanical property tests were conducted, and their application in building envelopes for low-income housing was analyzed. The results showed that the new material, when used as cladding on facades, can reduce heating and cooling demand. In a case study in Loja, a significant decrease in heating and cooling degree days was observed. This research opens new possibilities in the utilization of recycled materials in construction and can contribute to knowledge in this field.

Fatigue analysis plays a vital role in determining the structural integrity and life of a dental implant. With the use of such implants on the rise, there is a corresponding increase in the number of implant failures. As such, the aim of this research paper is to investigate the life of 3D-printed dental implants. The dental implants considered in this study were 3D printed according to the direct metal laser sintering (DMLS) method. Additionally, a finite element model was developed to study their performance, while fatigue life was predicted using Fe-Safe software®. The model was validated experimentally by performing fatigue tests. The life of the dental implants was analysed based on Normal strain and the Brown-Miller with Morrow mean correction factor algorithm. The model revealed that there was a strong correlation between the FEA and the experimental results. The clinical success of 3D-printed dental implant experimentally is 20.51 years and computationally under Normal strain is 19.89 years and Brown-Miller with Morrow mean correction factor is 26.82 years.

The objective of this study was to evaluate the drying kinetics of the mass of jambu leaves and mass of jambu leaves in foam mat at different temperatures (50, 60 and 70 °C and thickness of 1.0 cm). The physicochemical characterization of the materials was performed before and after drying. Twelve different drying models were fitted to the drying kinetics data and the thermodynamic properties were calculated. The physicochemical parameters for the mass of leaves and foam after drying were moisture content from 2 to 7%, ash from 13 to 17%, protein content from 22 to 30%, lipids from 0.6 to 4% and total titratable acidity from 0.20 to 0.28% of tartaric acid. Wang & Singh and Midilli models were recommended for describing the drying kinetics. The use of foam mat promoted higher values of effective diffusion coefficient and activation energy and lower values of enthalpy and entropy, thus enhancing the reduction of drying time.

The control of stereo-, regio-, and chemo-selectivity in transition-metal-catalyzed coupling reactions is a key topic in organic synthesis. Several methods for controlling selectivity have been reported thus far. On the other hand, the reduction of the catalyst loading in the reaction is one of the most important issues in organic synthesis from the standpoint of green sustainable chemistry. As another advantage of reducing the catalyst loading, the expression of the reaction selectivity and the substituent effect caused by the reduction of the catalyst loading to the parts-par-million (ppm) level in various catalytic reactions is presented herein.

A study was conducted to predict failure stresses, failure locations, and their paths of initiation of perforated polymethyl methacrylate (PMMA) specimens as they were loaded using pins inserted into the holes. First, a series of experiments were conducted for perforated PMMA coupons. There were six different types of coupons. The test specimens had three different widths with a circular hole of a diameter of 8 mm, which was placed at two different locations along the specimen length. All the specimens were loaded using a pin inserted into the hole with three different pins of nominal diameters of 8 mm, 6 mm, and 5 mm, respectively. To predict the failure and compare the results against the experimental data, the recently proposed universal failure criterion was used in the study using finite element analyses. The failure criteria gave acceptable results as compared to the experimental data.

Floodplains are critically important ecosystems that provide a whole suite of ecosystem services including nutrient and carbon sequestration, flood mitigation, water storage, and critical wildlife habitat to name a few. However, human modification of rivers and floodplains through channelization, artificial levee construction, reduction in active floodplain area, and water management can significantly reduce the ecosystem function of river-floodplain systems. In this study, we evaluated the changes in nutrient loading of the Kissimmee River floodplain during the restoration of the river-floodplain system. In addition to time-series loading analysis, we also evaluated soil nutrient concentrations across the lower portion of the Kissimmee River floodplain. During the 44-year nutrient loading time-series, the floodplain remained a nutrient exporter with changes in nutrient loading generally corresponding to both water quality (i.e. point source reductions) and hydrologic restoration activities in the watershed and Kissimmee River floodplain. During the study period, inputs of total phosphorus and total nitrogen loads from upstream either significantly increased or remained the same. In addition to external sources of nutrients, internal sources of nutrients from floodplain soils can also contribute to the total nutrient export from the system. These internal sources could be organic via the decomposition of organic matter or geologic from the original excavation of the canal and/or restoration backfilling. Soil nutrient concentrations vary between vegetative communities and landscape position and could be a significant source of phosphorus to the downstream system which is plagued by eutrophic conditions. Therefore, as floodplain function in the Kissimmee River continues to be restored and managed, additional effort may be needed to address nutrient inputs and internal legacy nutrients.

Abstract: Objective: analyze the effectiveness of the implementation of the Lean Healthcare sys-tem at the emergency room of the Clinical Hospital of the Federal University of Uberlândia (HC-UFU), based on a comparison of hospital indicators obtained over the three phases corre-sponding to the period of one year before the implementation (T1), the year during the imple-mentation (T2) and one year after implementation (T3). Material and Methods: this is applied research, classified as a case study, exploratory, descriptive that is developed in stages. Based herein on the search for hospital indicators, as occurred in the implementation process of Lean in Emergencies at the HC-UFU and a description of the implemented Lean system. Results and Discussions: during the period where it was possible to collect data relevant to the NEDOCS and LOS indicators, the motivation of the teams grew, but with a notable tension between municipal management and hospital management. It was found that, despite the fluctuations, the patient length of stay in the Emergency Room remained high. Noteworthy here is that with the excep-tion of the variable of female deaths before 24 hours of hospitalization, all other variables showed percentage increases before and after the intervention. Conclusion: the methodology followed for the implementation of Lean in Emergencies in the emergency sector of the hospital did not produce an improvement in hospital indicators.

It is shown that, for a de Sitter Universe, the Hartle-Hawking (HH) wave function can be obtained in a simple way starting from the Friedmann- Lemaitre-Robertson-Walker (FLRW) line element of cosmological equations. An oscillator having imaginary time is indeed derived starting from the Hamiltonian obtaining the HH condition. This proposes again some crucial matter on the meaning of complex time in cosmology. In order to overcome such difficulties, we propose an interpretation of the HH framework based on de Sitter Projective Holography.

Europium (Eu)-doped fluorapatite (FA) nanorods has a similar biocompatibility with hydroxyapatite (HA) in terms, attracted much attention as cell imaging biomaterials due to their luminescent property. Here, we will discuss the new feature of europium doped fluorapatite (Eu-FA) nanorods as anticancer drug carrier. Eu-FA nanorods was prepared using a hydrothermal method. The morphology, crystal structure, fluorescence and composition are investigated. The specific crystal structure, enabling an effective loading of drug molecules. Doxorubicin (DOX), used as an anticancer model drug, was shown to be effectively loaded onto the surface of the nanorods. The DOX release was fairly pH-dependent, occurring more rapidly at pH 5.5 than pH 7.4 was observed. The intracellular penetration of the DOX-loaded Eu-FA nanorods (Eu-FA/DOX) can be imaged in situ due to the self-fluorescence property. Treatment of melanoma A375 cells with Eu-FA/DOX elicited a more effective apoptosis rate than direct DOX treatment. Overall, Eu-FA show great promise for tracking and treating tumor, may potentially useful as a multifunctional carrier system to effectively load and sustainably deliver drugs.

In the present article, the application of an artificial neural network (ANN) model is studied, whose function is the development of plastic instability maps of a medium carbon microalloyed steel during the hot forging process. And, secondly, we proceed to create another neural network capable of providing the recrystallized grain size in the steady state phase resulting from the deformation by hot forging, thus creating a methodology that can be applied to different types of processes and materials. In order to achieve this objective, we start from the experimental data of a medium carbon microalloy steel, obtained by hot compression tests, for strain rates that vary between 10-4 and 3 s-1 and in a range of temperatures between 900 oC and 1150 oC. These experimental data will be used to train the neural network that is intended to be created in this work. Once trained, it will be verified if the results of the test correspond to the experimental data and the fluency curves will be obtained. Finally, the processing maps will be developed applying the Dynamic Materials Model (DMM), according to which the safe domains to forge the material and the plastic instability domains are delineated, to be avoided during the forging process. The maps obtained by means of RNA will be compared with the experimental ones and it will be possible to verify that the optimal regions of forging in the maps obtained by RNA coincide with those obtained by means of experimental data. In addition, a study of the influence of the microstructure on the behavior of steel during hot forming will be carried out, since the experimental tests are carried out at austenitizing temperature, so the microstructure is different in each test.

This article aimed at providing some extension of the modal square of opposition in the 1 light of Ockham’s account of the modal operators. Moreover, we shall set forth some significant 2 remarks on the de re-de dicto distinction and on the modal operator of contingency by means of a 3 Boolean algebra called Bitstring Semantics. This generalisation starting from Ockham’s account of 4 modalities will allow us to take into consideration whether Ockham’s thought on this matter holds 5 water or not, and in which case it should be changed in order to make it coherent.

A theoretical description of quantum jumps at the level of elementary particles is proposed, based on a micro-cosmological interpretation of their de Broglie phase. The third quantization formalism proposed in current literature for the description of baby universes in quantum cosmology is used here to describe the breakdown of unitarity in the transition from the pre-jump to the post-jump wave function. The corpuscular aspect manifested by the particle in the micro-interaction that originates the jump is represented by a pair of evanescent "micro-universes", respectively pre- and post-jump, connected by a wormhole. The latter represents the actual implementation of the interaction that leads to the projection on the outgoing state; this interaction is always local, even when the selected outgoing state is entangled. Therefore, the decoherence which leads to the emergence of classicality is originated by the same fundamental interactions of the Standard Model involved in the unitary evolution of the wave function. The objective nature of the reduction process admits implications on the possibility of using the formalism in the cosmological context, which are briefly discussed.

The signature of chaotic systems can be characterized either by the sensitivity of the initial conditions or by the change of its parameters. This feature can be used for manufacturing high sensitivity sensors. Sensors based on chaotic circuits have already been used for measuring water salinity, inductive effects, and both noise and weak signals. This article investigates an impedance sensor based on the Van der Pol and Duffing damped oscillators. The calibration process is a key point and therefore the folding behavior of signal periods was also explored. A sensitivity of 0.15 kΩ/Period was estimated over a range from 89.5 to 91.6 kΩ. This range can be adjusted according to the application by varying the gain of the operational amplifier used in this implementation. The development of this type of sensor might be used in medical and biological engineering for skin impedance measurements, for example. This type of chaotic sensor has the advantage of sensing small disturbances and then detect small impedance changes within biological materials which, in turn, may not be possible with other detectors.

Drug delivery through Liposomes has shown tremendous potential in terms of the therapeutic application of nanoparticles. There are several drug-loaded liposomal formulations approved for clinical use that help mitigate harmful effects of life-threatening diseases. Developments in the field of liposomal formulations and drug delivery have made it possible for clinicians and researchers to find therapeutic solutions for complicated medical conditions. A key aspect in the development of drug-loaded liposomes is a careful review of optimization techniques to improve the overall formulation stability and efficacy. Optimization studies help in improving/modulating the various properties of drug-loaded liposomes and are vital for the development of this class of delivery systems. A comprehensive overview of the various process variables and factors involved in the optimization of drug-loaded liposomes is presented in this review. The influence of different independent variables on drug release and loading properties with the application of a statistical experimental design is also explained in this article.

This paper aims to determine the effect of local corrosion at three different corrosion areas, the 1. entire area, 2. constant moment area, and 3. constant shear area, on the flexural performance of RC beams. To analyze this, an experimental study was carried out to prepare two series of RC beams (200×300×2800mm) created with three different degree of corrosion inducing local rebar corrosion. Furthermore, two-series of experimental tests were conducted under different loading types by monotonic and cyclic loading. It was observed that strength capacity reduction grows in the order of the corroded RC specimens induced: the 1. entire area > 2. constant moment area > 3. constant shear area, as the average corrosion rate increases. Our test results further show that the yield and ultimate strength was kept nearly equivalent to the uncorroded RC specimen by the average corrosion rate of 10% and 15%, respectively. Over these corrosion rates, the yield strength and ultimate strength dropped significantly. Compared to test results under a monotonic loading condition, the structural capacity under a cyclic loading condition decreased with a more pronounced tendency for each corrosion case as the corrosion rate increased. A longitudinal crack was developed throughout and adjacent to the corrosion areas, as the corrosion rate increased. Thus, we can infer that strength reduction may be strongly influenced by this longitudinal crack.

Numerous elements, such as the composition and characteristics of carbon nanomaterials, the composition and characteristics of the matrix material, moisture levels, temperature, and loading circumstances, influence the piezoresistive behaviour of self-sensing cementitious composites. While some past research has explored the impact of some of these factors on the performance of self-sensing cementitious composites, additional investigations need to be conducted to delve into how loading conditions affect the sensitivity of self-sensing cement-stabilized composites. Therefore, this study explores the influences of various loading conditions (i.e., location of loading regarding the location of recording electrodes, and loading level) on the electromechanical performance of self-sensing cement-stabilized sand. To this end, firstly, the evaluation of the percolation threshold based on 10% cement-stabilized sand specimens containing various multiwall carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) was performed. Then, 10% cement-stabilized sand containing 4% MWCNTs/GNPs was tested under various cyclic compressive stresses. The results suggested that the distance between the loading area and the electrode location used for recording the electrical resistance significantly impacts the sensitivity of cement-stabilized sand. Optimal sensitivity was achieved when the electrodes were positioned directly beneath the loading area. Moreover, the study yielded that the stress sensitivity of self-sensing cement-stabilized sand increases proportionally with the stress level. Examination through scanning electron microscopy (SEM) demonstrated that the loading condition influences the bridging characteristics of carbon nanomaterials in cement-stabilized sand, leading to diverse electromechanical behaviors based on the loading condition. This study underscores the importance of considering specific parameters when designing the application of self-sensing cement-stabilized sand for practical field use.

Soluble noble metal salts are widely used for loading noble metals as nano-catalysts in many applications. In this paper, Pt-SnO2 composite nanoceramics were prepared from SnO2 nanoparticles and H2PtCl6 using two Pt-loading methods separately: For the solution reduction method, the H2PtCl6 solution was added to a suspension of SnO2 and zinc powder to form Pt on SnO2 nanoparticles; and for the impregnation method, Pt was formed from H2PtCl6 in the course of sintering. Although a series of samples prepared using both Pt loading methods showed a strong response to H2 at room temperature, the ones prepared using the solution reduction method exhibited much better room temperature hydrogen sensing characteristics. For two samples of 0.5 wt% Pt and sintered at 825°C, the response value for the sample prepared using the solution reduction method was 5300 to 1% H2-20% O2-N2, which was much larger than that of 150 for the sample prepared using the impregnation method. Samples prepared using the two Pt loading methods have similar microstructures as characterized by XRD, FESEM, EDS, TEM, and HRTEM. However, the residual chlorine content in those using the impregnation method was found to be higher than that using the solution reduction method through analysis. It is proposed that the striking difference in the room temperature hydrogen sensing characteristics among samples prepared using these two different Pt loading methods separately resulted from their different chlorine removal process. This study demonstrates the importance of a proper method in loading noble metals from their soluble salts as nano-catalysts in many applications.

Encapsulation of antioxidant polyphenols leads to increase solubility and bioavailability of these micronutrients in solution. The encapsulation of antioxidant resveratrol, genistein and curcumin by folic acid-chitosan nanocapsules was studied in aqueous solution, using multiple spectroscopic methods, TEM images. Structural analysis showed that polyphenol bindings are via hydrophilic, hydrophobic and H-bonding contacts with resveratrol forming more stable conjugates. As chitosan size increased, the binding efficacy and stability of polyphenol-polymer adducts were increased. Polyphenol binding induced major alterations of chitosan morphology. Chitosan nanoparticles are capable of delivery of polyphenols in vitro.

Increasing the loading density of nanoparticles on carbon support is essential for making Pt-alloy/C catalysts practical in H2-air fuel cells. The challenge lies in increasing the load-ing while suppressing the sintering of Pt-alloy nanoparticles. This work presents a 40% Pt-weighted sub-3 nm PtCo/C alloy catalysts via a simple incipient wetness impregnation method. By carefully optimizing the synthetic conditions such as Pt/Co ratios, calcination temperature and time, the size of supported PtCo alloy nanoparticles is successfully con-trolled below 3 nm, and a high electrochemical surface area achieves of 94 m2/g is achieved, which is 2.8 times of commercial PtCo/C-TKK catalysts. Demonstrated by elec-trochemical oxygen reduction reaction, PtCo/C alloy catalysts present an enhanced mass activity of 0.45 A/mg at 0.9 V vs. RHE, which is 1.7 times that of PtCo/C-TKK catalyst. Therefore, the developed PtCo/C alloy catalyst can potentially be a highly practical cata-lyst for H2-air fuel cells.

It is unclear whether military shoes (combat boots and sports shoes) attenuate loading rate or affect force transfer during walking. Therefore, this study compared ground reaction forces (GRF) related to impact and force transfer between combat boots, military sports shoes and running shoes. Ten army recruits walked over a walkway with two force plates embedded. GRF were measured when walking barefoot (for data normalization) and with combat boots, military sports shoes and running shoes. Loading rate, first and second peak forces and push-off rate of force were computed along with temporal analysis of waveforms. Reduced loading rate was observed for the running shoe compared to the combat boot (p = 0.02 and d = 0.98) and to the military sports shoe (p = 0.04 and d = 0.92). The running shoe elicited a smaller second peak force than the combat boot (p < 0.01 and d = 0.83). Walking with military shoes and combat boots led to larger force transfer then running shoes potentially due to harder material used in midsole composition (i.e. styrene-butadiene rubber). These results could lead to a potentially larger risk of injuries while long duration walking in military shoes and boots compared to traditional running shoes.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

We are using information from a paper deriving a Lorentz-violating energy-momentum relation entailing an exact mo_mentum cutof as stated by G. Salesi . Salesi in his work allegedly defines Pre Planckian physics, whereas we restrict our given application to GW generation and DE formation in the first 10^-39s to 10^-33s or so seconds in the early universe. This procedure is inacted due to an earlier work whereas referees exhibited puzzlement as to the physical mechanism for release of Gravitons in the very early universe. The calculation is meant to be complementary to work done in the Book “Dark Energy” by M. Li, X-D. Li, and Y. Wang, and also a calculation for Black hole destruction as outlined by Karen Freeze, et. al. The GW generation will be when there is sufficient early universe density so as to break apart Relic Black holes but we claim that this destruction is directly linked to a Lorentz violating energy-momentum G. Salesi derived, which we adopt, with a mass m added in the G. Salesi energy momentum results proportional to a tiny graviton mass, times the number of gravitons in the first 10^-43 seconds

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

This experimental study investigates the effect of scarf geometry in restoring the impact response of scarf patched 3 mm thick glass-fibre reinforced polymer (GFRP) matrix composite laminates. Traditional circular along with rounded rectangular scarf patch configurations considered as repair patches. Experimental measurements revealed that the temporal variations of force and energy response of the pristine specimen are close to that of circular repaired specimens. The predominant failure modes were witnessed only in repair patch which include the matrix cracking, fibre fracture, delamination and no discontinuity in adhesive interface was witnessed. When compared with the pristine samples, the top ply damage size of the of the circular repaired specimens is larger by 9.91 %, while that of the rounded rectangular repaired specimens is larger by 434.23 %. The results show that circular scarf repair is more suitable choice of repair approach under the condition of 37J low-velocity impact event even though the global force-time response is similar.

This work presents a multi-start algorithm for solving the capacitated vehicle routing problem with two-dimensional loading constraints (2L-CVRP) allowing for the rotation of goods. Researches dedicated to graph theory and symmetry considered the vehicle routing problem as a classical application. This problem has complex aspects that stimulate the use of advanced algorithms and symmetry in graphs. The use of graph modeling of the 2L-CVRP problem by undirected graph allowed the high performance of the algorithm. The developed algorithm is based on metaheuristics such as the Constructive Genetic Algorithm (CGA), to construct promising initial solutions; a Tabu Search (TS), to improve the initial solutions on the routing problem; and a Large Neighborhood Search (LNS), for the loading subproblem. Although each one of these algorithms allowed to solve parts of the 2L-CVRP, the combination of these three algorithms to solve this problem was unprecedented in the scientific literature. In our approach, a parallel mechanism for checking the loading feasibility of routes was implemented using multi-threading programming to improve the performance. Additionally, memory structures, like hash-tables, were implemented to save time by storing and querying previously evaluated results for the loading feasibility of routes. For benchmarks, tests were done on well-known instances available in the literature. The results proved that the framework matched or outperformed most of the previous approaches. As the main contribution, this work brings higher quality solutions for large-size instances of the pure CVRP. This paper involves themes related to the symmetry journal, mainly complex algorithms, graphs, search strategies, complexity, graph modeling, and genetic algorithms. In addition, the paper especially focuses on topic-related aspects of special interest of the community involved in symmetry studies, such as, graph algorithms and graph theory.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

The use of new developed high-strength steel in concrete members can reduce steel bars congestion and construction costs. This research aims to study the behavior of concrete columns reinforced with new developed high-strength steel under eccentric loading. Ten reinforced concrete columns were fabricated and tested. The test variables are transverse reinforcement amount and yield strength, eccentricity, and longitudinal reinforcement yield strength. The failure patterns are compression and tensile failure for columns subjected to small eccentricity and large eccentricity, respectively. The same level of post-peak deformability and ductility only can be obtained with lower amount of transverse reinforcement when high-strength transverse reinforcements are used in columns subjected to small eccentricity. The high-strength longitudinal reinforcement can improve bearing capacity and post-peak deformability of concrete columns. Besides, three different equivalent rectangular stress block (ERSB) parameters in predicting bearing capacity of columns with high-strength steel were discussed based on test and simulated results. It is concluded that the Code of GB 50010-2010 overestimates the bearing capacity of columns with high-strength steel, whereas bearing capacities computed using Codes of ACI 318-14 and CSA A23.3-04 agree well with test results.

The present paper deals with the stochastic modeling of bio-colonization for the computation of stochastic hydrodynamic loading on jacket-type offshore structures. It relies on a multidisciplinary study gathering biological and physical research fields that accounts of uncertainties at all the levels. Indeed, bio-colonization of offshore structures is a complex phenomenon with two major but distinct domains (i) marine biology whose processes are modeled with biomathematics methods and (ii) hydrodynamic processes. This paper aims to connect these two domains. It proposes a stochastic model for the marine organism’s growth and then continues with transfers for assessment of drag coefficient and forces probability density functions that accounts for marine growth evolution. A case study relies on the characteristics (growth and shape) of the blue mussel (Mytilus edulis) in northeastern Atlantic.

In 2011 over 1.7 million people were hospitalized because of a fragility fracture, and direct costs associated with osteoporosis treatment exceeded 70 billion dollars in the United States. Failure to reach and maintain optimal peak bone mass during adulthood is a critical factor in determining fragility fracture risk later in life. Physical activity is a widely accessible, low cost, and highly modifiable contributor to bone health. Here, we will review the evidence linking exercise and physical activity to bone health in women. Bone structure and quality will be discussed, especially in the context of clinical diagnosis of osteoporosis. We will review the mechanisms governing bone metabolism in the context of physical activity and exercise. Questions such as, when during life is exercise most effective, and what specific types of exercises improve bone health, will be addressed. Finally, we will discuss some emerging areas of research on this topic, and will summarize areas of need and opportunity.

Introduction: The HIV/AIDS pandemic in Spanish prison institutions has led to a series of necessary changes to adapt and provide an effective response. Materials and Methods: This research was conducted from an interpretative paradigm with a phenomenological perspective, interpreting the experiences of nursing professionals in Spanish prison institutions. Focus groups were conducted with professionals who worked before and after the emergence of antiretroviral treatments through the Microsoft Teams platform, using the ATLAS Ti v.9 software. The project received approval from the Ethics Committee of the UJI university. Results: Limited dissemination of news in the press regarding HIV/AIDS and Spanish prisons was observed. Changes occurred in organizational, material, and personnel resources, requiring adaptation among nursing professionals. The available resources and difficulties are described, along with patient perspectives, the role of professionals, their environment, and their experiences, both positive and negative. Discussion and Conclusions: There is minimal visibility of the problem, and a description is provided of an adaptation process to the environment compatible with the Callista Roy´s model.

This article aims to approach the Mudejar architecture developed in Mexico during the 16th and 17th centuries. The subject has been little studied although both general and specific contributions have been made by the author’s research group. At the methodological level, this study is based on the existing bibliography as well as archive and field research which allow an accurate scientific approach and results. The article analyses the social and productive conditions in Mexico during the Viceregal period along with the systematization carried by the Viceroy Antonio de Mendoza, the guild ordinances and the architectural typologies. The perception of territory and the use of constructive models by the Viceregal authorities would justify the use of the Mudejar style as cultural and unity criteria

It is already known that a simple nonlocal de Sitter gravity model, which we denote as dS gravity, contains an exact vacuum cosmological solution which mimics dark energy and dark matter and is in very good agreement with the standard model of cosmology. This success of dS gravity motivated us to investigate how it works at lower than cosmic scale – galactic and the solar system. This paper contains our investigation of the corresponding Schwarzschild-de Sitter metric of the dS gravity model. To get exact solution, it is necessary to solve the corresponding nonlinear differential equation, what is a very complicated and difficult problem. What we obtained is a solution of linearized equation, which is related to space metric far from the massive body, where gravitational field is weak. The obtained approximate solution is of particular interest for examining the possible role of non-local de Sitter gravity dS in describing the effects in galactic dynamics that are usually attributed to dark matter. The solution has been tested on the Milky Way and the spiral galaxy M33 and is in good agreement with observational measurements.

In the same way as the realization of some of the famous gedanken experiments imagined by the founding fathers of quantum mechanics has recently led to the current renewal of the interpretation of quantum physics, it seems that the most recent progresses of observational astrophysics can be interpreted as the realization of some cosmological gedanken experiments such as the removal from the universe of the whole visible matter or the cosmic time travel leading to a new cosmological standard model. This standard model involves two dark components of the universe, dark energy and dark matter. Whereas dark energy is usually associated with the cosmological constant, we propose to explain dark matter as a pure QCD effect, namely a gluonic Bose Einstein condensate, following the transition from the quark gluon plasma phase to the colorless hadronic phase. Our approach not only allows us to assume a ratio Dark/Visible equal to 11/2 but also provides gluons and (anti-)quarks with an extra mass of vibrational nature. Such an interpretation would comfort the idea that, apart from the violation of the matter/antimatter symmetry satisfying the Sakharov’s conditions, the reconciliation of particle physics and cosmology needs not the recourse to any ad hoc fields, particles or hidden variables.

An explanation of the origin of dark matter is suggested in this work. The argument is based on symmetry considerations about the concept of mass. In the Wigner's view, the rest mass and the spin of a free elementary particle in flat space-time are the two invariants that characterize the associated unitary irreducible representation of the Poincar\'e group. The Poincar\'e group has two and only two deformations with maximal symmetry. They describe respectively the de Sitter (dS) and Anti de Sitter (AdS) kinematic symmetries. Analogously to their shared flat space-time limit, two invariants, spin and energy scale for de Sitter and rest energy for Anti de Sitter, characterize the unitary irreducible representation associated with dS and AdS elementary systems. While the dS energy scale is a simple deformation of the Poincaré rest energy and so has a purely mass nature, AdS rest energy is the sum of a purely mass component and a kind of zero-point energy derived from the curvature. An analysis based on recent estimates on the chemical freeze-out temperature marking in Early Universe the phase transition quark-gluon plasma epoch to the hadron epoch supports the guess that dark matter energy might originate from an effective AdS curvature energy.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

A reliable finite element procedure to simulate shear-dominated ductile fracture in large-scale, thin-walled steel structures is still evolving due primarily to the challenges in determining the fracture criterion of steel materials under complex stress states. This paper aims to examine the accuracy of the modified Gurson-Tvergaard-Needleman (GTN) model considering the shear failure in simulating ductile fracture of steel plate structures under quasi-static punch loading. The modified GTN damage models are performed by ABAQUS user defined material subroutine (VUMAT). The void related parameters and shear damage parameters of Xue’s and N-H modified GTN models are calibrated from test specimens with various geometries corresponding to different stress triaxiality and shearing conditions. The damage evolution associated with the shearing of voids in the modified GTN models has strong influences on the stress triaxiality versus equivalent plastic strain under complex stress states, especially for the shear dominated loading conditions. Based on the original GTN model, Xue’s model, and N-H modified GTN model with calibrated material parameters, a numerical comparative study examines the ductile fracture of steel non-stiffened plate and stiffened plate under punch loading. Benchmarked against the experimental studies, the numerical simulations demonstrate that the shear driven void evolution in the modified GTN model imposes significant effects on the load-displacement responses, as well as the onset and extension of ductile fracture in steel plates under punch actions. The N-H modified model with calibrated shear damage parameters shows a better correlation with the ductile fractures in steel plates observed in the experiment, than the original GTN model and Xue’s modified GTN model. As a result of this study, the modified GTN model considering the shear failure can be applied for practical applications in the crashworthiness assessment of ship collision and grounding.

Defensive structure is important in transportation field for kinds of intentional or unintentional explosion. Structures subjected to unconfined and confined explosion will bear different blast loads and their dynamic responses are different. The present work focus on the dynamic response mechanism of steel plate under unconfined and confined blast loads through both numerical and experimental studies. In the experiment, Digital Image Correlation (DIC) technique was applied to record and analyze the dynamic response process of large-scale field blast test. The DIC measured curve and the numerical calculated curves agrees well in both the trends and the peak values. Then, the dynamic response mechanism of steel plate under unconfined blast (UB) load and confined blast (CB) load were compared and discussed. Results show that the dynamic response of plate can be divided into three phases under both UB and CB loads, while with different mechanism. In phase I, plastic hinge starts from the center and moves to the boundary in UB condition, while in case of CB, plastic hinge occurs close to the boundary and moves in the opposite direction. In phase II, two plastic hinge lines propagates towards each other, and a platform exists between the boundary and the central area remains undeformed in UB condition, while in CB condition, larger deformation in peripheral region rather than central area produces.

Excessive nutrient discharge to tropical island coastlines drives eutrophication and algal blooms with significant implications for reef ecosystem condition and provision of ecosystem services. Management actions to address nutrient pollution in coastal ecosystems include setting water quality standards for discharging surface waters. However, these standards do not account for the effects of groundwater discharge, variability in flow, or dilution, all of which may influence assessment of true nutrient impacts on nearshore reef habitats. We developed a method to estimate dissolved inorganic nitrogen (DIN) loads to coastal zones by integrating commonly available datasets within a geospatial modeling framework for Tutuila, American Samoa. The DIN loading model integrated an open-source water budget model, water sampling results, and publically available streamflow data to predict watershed-scale DIN loading to the island’s entire coastline. When compared to surface water pathways, submarine groundwater discharge (SGD) was determined to be the most important coastal delivery mechanism of terrigenous DIN, which supports findings from other tropical islands. Onsite wastewater disposal systems were also found to be the primary anthropogenic sources DIN to coastal waters. Our island-wide DIN loading model provides a simple and robust metric to define spatially-explicit sources and delivery mechanisms of nutrient pollution to nearshore reef habitats. Understanding the sources and primary transport modes of inorganic nitrogen to nearshore reef ecosystems can have significant implications for place-based management interventions aimed at increasing the adaptive capacity of unique island ecosystems to environmental variation and disturbances.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

Slow and controlled release systems for drugs, have attracted increasing interest recently. A highly efficient metal-organic gels (MOGs) drug delivery carrier, i.e., MIL-100(Al) gels, has been fabricated by a facile, low cost and environment friendly one-pot process. The unique structure of MIL-100(Al) gels leads to a high loading efficiency (620 mg/g) towards doxorubicin hydrochloride (DOX) as a kind of anticancer drugs. DOX-loaded MOGs exhibited high stability under physiological conditions and sustained release capacity of DOX for up to 3 days (under acidic environments). They further showed sustained drug release behavior and excellent antitumor effects in in vitro experiments on HeLa cells, in contrast with the extremely low biotoxicity of MOGs. Our work provides a promising way for the anticancer therapy, by utilizing this MOGs-based drug delivery system, as an efficient and safe vehicle.

This article focuses on the comparison and perception of the potential of water’s surface in selected parts of the waterfront in two contrasting cities. The aim is to define the potential of the water’s surface in terms of psychology and its effects on climate. The analysis was performed on the example of Prague with its waterfront on the river Vltava, and Santa Cruz de Tenerife with its Atlantic coastline. Data was sourced from maps, questionnaire surveys and interviews with waterfront users during October 2020. The research showed a higher importance of the water’s surface for users in Prague, than in Santa Cruz. The main finding is that the psychological perception of the waterfront by its the users is affected by the possibility of a visual contact with the water’s surface, the design and composition of the space, and the climate situation of a site affected by the presence of an urban heat island (UHI). The results promote an adherence to ecosystem-based approaches in future design projects and modifications of existing public spaces. The purpose of the work is to open a broader debate on the sustainability of the potential of waterfronts and their positive impact on human health.

The prevalence and incidence of cardiac pro-arrhythmic disorders are often influenced by sex due to specific effects on the QT interval. Androgens shorten QT, which may be protective against acquired long QT syndromes and their related arrhythmias in men such as torsade de pointes (TdP). On the other hand, androgens can potentiate Brugada and early repolarization syndromes, which are most prevalent in men. In this case series, we highlight four male patients with aborted SCD in the setting of abnormal testosterone status; two patients with TdP in a setting of testosterone deprivation (of which one drug-induced) and 2 patients with ventricular fibrillation associated with exogenous androgenic booster (Tribulus terrestris) intake. From this case series, we review the current available literature of the effects of androgen as a double-edged sword on the QTc interval and emphasize the importance of QTc monitoring in this subset of patients.

The origin of SARS-CoV-2 is debated, even after 18 months into the COVID-19 pandemic and a special investigation conducted by the World Health Organization. The RaTG13 sequence has been a highlight of discussions surrounding the origin of SARS-CoV-2. Here we express our opinion about the need for better reporting standards for information about sequencing data, especially for pathogens, citing our findings with the reported RaTG13 genome.

A thin-shell wormhole is crafted by the cut-and-paste method of two Bardeen de-Sitter black holes using Darmois-Israel formalism. Energy conditions are considered for different values of magnetic charge while both mass and cosmological constant are fixed. The attractive and repulsive characteristics of the throat of the thin-shell wormhole are also examined through the radial acceleration. Dynamics and stability of the wormhole are studied around the static solutions of the linearized radial perturbations at the throat of the wormhole. The regions of stability are determined by checking out the condition of concavity of the potential as a function in the throat radius for different values of magnetic charges.

This paper discusses the impact of orthographic manuals on the state of literacy, i.e. the relation of orthographic literacy and orthographic standardisation. The established hypothesis claims that frequent changes of orthographic rules during the pupils’ primary and secondary education do not have any considerable impact on their orthographic habits. In other words, the quantity of orthographic mistakes observed during a longer period of time and in conditions of changed orthographic rules would not show significant oscillations in their spelling. In order to confirm the hypothesis, a questionnaire was conducted encompassing 41 tests among 526 students of a technical study programme during four consecutive academic years, pursuant to whose results a writing uniformity index and a categorisation of orthographic controversy into six classes is established. The Croatian language has been selected for the observation due to multiple orthographic changes in the last 30 years in the three major orthographic points: writing of the covered r, writing of d and t in front of c and č in declination of words ending in -tak, -tac, -dak and -dac, and the issue of compound or separate spelling of the negation particle and the auxiliary biti (to be). Moreover, the paper methodologically and quantitatively establishes criteria according to which the second established hypothesis on evolutionary orthographic literacy can be confirmed. The conclusions are expected to be able to contribute to the better understanding of orthographic planning and application of orthographic norms in schools.

Biofilter application for treatment of stormwater containing de-icing chemicals commonly applied in airports, propylene glycol and potassium formate, was investigated. Lab-scale adsorption tests using filter media made of crushed clay (Filtralite) and granular activated carbon showed that adsorption was unsuitable for removal of propylene glycol and potassium formate. Column filtration experiment testing two different crushed clay size ranges was conducted. The results showed that DOC removal was dependent on a number of factors. This study investigated the impact of filter depth, nutrients addition, and filtration rate. DOC removal suggested that DOC degradation occurred on the top filter layer. It was shown that the most active separation occurred in the first ~20 cm of filter depth. This was confirmed by results from water quality analysis (i.e. DOC removal and ATP measurement) and calculations based on a filtration performance analysis (Iwasaki model) and filter hydraulic evaluation (Lindquist diagram). It was shown that for the highest C:N:P ratio tested (molar ratio of 24:7:1), 50-60% DOC removal was achieved. Addition of nutrients was found important and determining the biofilter performance.

To solve the problem of a uneven load for a dual-input counter-rotating transmission system, this research is based on Small Displacement Torsor Jacobian-Torsor theory.Considering the influence of the local parallel chain of a gearbox on the calculation accuracy of the backlash,the processing method of a meshing tooth pair parallel chain is proposed. The probability distribution of the tolerance band of gearbox manufacturing and assembly errors is modeled, the three-dimensional tolerance analysis model of a dual-input counter-rotating gearbox is established, and the Monte Carlo method is used to solve the backlash of the output end. The output backlash is solved with the Monte Carlo method, and the theoretical design backlash is combined with the output backlash to derive the gearbox side clearance range. The gearbox shaft system is analyzed statically, the range of the equal load coefficient is calculated, and the equal load performance optimization method based on the matching relationship between the gear backlash and the elastic shaft torsional stiffness is proposed. The correctness of the three-dimensional tolerance analysis combined with the elastic deflection angle used to optimize the equal load performance of the dual-input counter-rotating transmission system is verified by comparison with the relevant test data.

Airworthiness certification requires proof of structure strength, which is performed generally through building block approach. To achieve this, representative intermediate scale experiments generated by test benches are in general needed, additionally to material characterization at coupons scale and structure testing at large scale. The VERTEX test bench can generate combined loading of tension/compression-shear-pressure on structural elements and was modelled with Finite Elements to perform virtual testing representative of its intermediate-scale specificity. The numerous bolted joints of the bench were modelled and their behavior identified in previous tests, so the model could quantitatively estimate the transfer function of the bench, which is the relation between the displacements imposed by the jacks and the resulting loads on a given sample. The VERTEX model was identified to represent load shapes and amplitudes on a training set, and was later confronted to a validation set of tests of tension and shear. A model with ideal boundary conditions was also developed for comparison but it failed to predict some load shape specificities and did not give any indication of loading amplitude. Application cases of the developed model are shown to assess a range of virtual testing possibilities.

The mechanical properties of α-chitin and chitosan biocomposite are investigated due to their broad range of potential applications in bioengineering, materials science, and environmental technology. Employing molecular dynamics (MD), and stress-strain analyses, this study comprehensively investigates biopolymers mechanical response and anisotropic mechanical behavior under uniaxial tensile loading conditions in an aqueous environment. Our computational models were validated against existing experimental data, showing high degrees of correspondence. Uniaxial tensile tests revealed that α-chitin exhibits a remarkable ultimate tensile strength (UTS) of 10.07 GPa in the crystalline chain direction (y-axis) at a high strain rate of 0.636, compared to a significantly lower UTS of 2.78 GPa in the perpendicular direction (x-axis) at a lower strain rate of 0.066. The biocomposite nanostructure, encompassing randomly distributed chitosan, reduced stiffness, maintaining remarkable flexibility as α-chitin, with a UTS of 5.03 GPa in the y-axis and 2.34 GPa in the x-axis. Further, the directional elastic modules for α-chitin were calculated as 51.76 GPa and 39.76 GPa in the x and y directions, respectively. In contrast, these values for the α-chitin-chitosan biocomposite were estimated as 31.66 GPa and 26.00 GPa, respectively. The findings provide valuable insights into the distinct mechanical properties of α-chitin and chitosan biocomposite, making a substantial contribution to optimizing these materials for specialized applications.

In past years, lithium-ion batteries (LIBs) can be found in every aspect of life, and batteries, as energy storage systems (ESSs), need to offer electric vehicles (EVs) more competition to be accepted in markets for automobiles. Thick electrode design could reduce the use of non-active materials in batteries that its energy density would be improved and its cost would be cut. However, thick electrodes are limited by their weak mechanical stability and poor electrochemical performance, these limitations could be classified as the critical cracking thickness (CCT) and the limited penetration depth (LPD). The understanding of the CCT and the LPD have been proposed and the recent works on breaking the CCT and improving the LPD are listed in this article. By comprising these attempts, some thick electrodes could not offer higher mass loading or higher accessible areal capacity that would defeat the purpose.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

Extracellular vesicles are considered a novel therapeutic tool, due to their ability to transfer their cargoes to target cells. Different strategies to directly load extracellular vesicles with RNA species have been proposed. Electroporation has been used for the loading of non-active vesicles, however the engineering of vesicles already carrying a therapeutically active cargo is still under investigation. We here set up a coincubation method to increase the anti-tumor effect of extracellular vesicles isolated from human liver stem cells (HLSC-EVs). Using the coincubation protocol, vesicles were loaded with the anti-tumor miRNA-145, and their effect was evaluated on renal cancer stem cell invasion. Loaded HLSC-EVs maintained their integrity and miR transfer ability, and miR-145 was protected by RNAse digestion possibly due to its binding to RNA-binding proteins on HLSC-EV surface, such as Annexin A2. Moreover, miR-145 coincubated HLSC-EVs were more effective in inhibiting the invasive properties of cancer stem cells, in comparison to naïve vesicles. The protocol reported here exploits a well-described property of extracellular vesicles to bind nucleic acids on their surface and protect them from degradation, in order to obtain an effective miRNA loading that results in the increase of the effect of naïve active extracellular vesicles.

Culverts are often required under earth embankment to allow for the crossing of a watercourse, like streams, to prevent the road embankment from obstructing the natural waterway. The opening of the culvert is determined based on the waterway required to accommodate the design flood, whereas the thickness of the culvert section is designed based on the loads applied to the culvert. This paper studies some design parameters of box culverts, such as the thickness of the haunch, the coefficient of earth pressure, the thickness of box culvert, and depth of fill on the top slab, to show the effect of haunch on the stresses of the box culvert. The study investigated the variation in stresses and the cost comparison made for different width of the box culvert. The percentage reduction in the cost of culvert based on the presence of haunch is presented.

A novel polymer containing β-cyclodextrin, α-cyclodextrin, γ -cyclodextrin and chitosan (cy-clodextrin-chitosan) was synthesized, characterized and used for extracting two kinds of pharmaceuticals ibuprofen and progesterone. This polymer is amorphous and porous with a high swelling capacity. The cyclodextrin-chitosan polymer exhibits high extraction capacity towards progesterone and ibuprofen. Add to that, the effect of different operator variables was studied and discussed (i.e., the effects of contact time, solute concentration, pH, ionic strength and temperature). In this study adsorption kinetic was investigated, where it follows a pseudo-second order model in case of ibuprofen and progesterone.

Introduction: Research studies have shown that workplace stress and physical immobility can have a multi-layered effect on the human body. It causes degrade our physical functioning, and also having negative effect on our performance. Yoga techniques have proved to be effective at various levels, including physical, mental, and emotional health. Objective: This study aimed to determine the efficacy of a short-term Yoga protocol – Y break, for improved well-being and resilience to stress. It is intended to working population at work to de-stress, refresh, and refocus. Methods: This study was conducted as a single-arm, multi-centric, experimental pilot trial. Prominent yoga institutes in six metropolitan cities were engaged in this study. Participants practised specific yoga techniques for 5 minutes, twice a day, for 15 days. Pre & post-intervention data was collected along with feedback about the protocol. A self-report questionnaire, based on the Pancha kosha parameters, was used to record pre- and post-data. Results: The Statistical data analysis shown significant improvement in every parameter selected for the study. Conclusion: A five-minute yoga break can do wonders for the health-related parameters of the working population; therefore, it should be introduced in all organizations to improve the quality of life and work.

We consider a real scalar field in de Sitter background and compute its thermal propagators. We propose that in a dS/CFT context, non-trivial thermal effects as seen by an `out' observer can be encoded in the anomalous dimensions of the d=3 Ising model. One of these anomalous dimensions, the critical exponent eta, fixes completely a number of cosmological observables, which we compute.

The study of phytotherapy in dentistry is relevant due to the low occurrence of research in the treatment of oral pathologies, such as caries and periodontal disease. Thus, the aim of this research was to characterize the chemical composition of extracts from the leaves of Couroupita guianensis Aubl, including toxicological evaluation and the antioxidant and antimicrobial potential against Staphylococcus aureus, Streptococcus mutans and Candida albicans. Three extracts were prepared using assisted ultrasound, originating the Crude Ultrasound Extract (CUE) and Soxhlet apparatus, originating the Crude Soxhlet Extract (CSE) and the Ethanol Soxhlet Extract (ESE). In the analysis of the chemical composition, the presence of flavonoids, tannins and saponins were detected. LC-DAD analysis revealed the presence of caffeic acid, sinapic acid, rutin, quercetin, luteolin, kaempferol and apigenin in all extracts. In the GC-MS analysis, stigmasterol and β-sitosterol were identified in CUE and CSE. The antioxidant potentials, determined by the DPPH• and ABTS•+ methods, the ESE showed higher antioxidant activity (2.98 ± 0.96 and 4.93 ± 0.90, respectively). In the evaluation of toxicity, the CUE 50µg/mL and the ESE 50 µg/mL presented growth stimulation of Allium cepa roots. At a concentration of 750µg/mL, all extracts inhibited root growth. None of the extracts showed toxicity against Artemia salina. Antibacterial action was detected in all extracts, mainly against the microorganisms S. aureus and S. mutans; however, the antifungal action against C. albicans was not detected. From the results, the extracts of C. guianensis have therapeutic potential for use in the control of microorganisms in the oral microbiota.

With the advancement of long-read sequencing technologies and their more widespread use for bacterial genomics, several methods for generating genome assemblies from error-prone long reads have been developed. These are complemented by various tools for assembly polishing using either long reads, short reads, or reference genomes. End users are therefore left with a plethora of possible combinations of programs for obtaining a final trusted assembly. Hence, there is also the need for measuring completeness and accuracy of such assemblies, for which, again, several evaluation methods implemented in various programs are available. In order to automatically run all these programs, I developed two workflows for the workflow management system Snakemake for bacterial genome assembly and evaluation of assemblies, which provide end users with an easy-to-run method for both tasks. The workflows are available as open source software under the MIT license at https://github.com/pmenzel/ont-assembly-snake and https://github.com/pmenzel/score-assemblies.

We report on the study of ultrafast laser-induced plasma expansion dynamics in a gas microjet. To this purpose, we focused femtosecond laser pulses on a nitrogen jet produced through a homemade De Laval micronozzle. The laser excitation leads to plasma excitation with a characteristic spectral line emission at 391 nm. By following the emitted signal with a detection system based on an Intensified Charge-Coupled Device (ICCD) we captured the two-dimensional spatial evolution of the photo-excited nitrogen ions with a temporal resolution on the nanosecond time scale. We fabricated the micronozzle on fused silica substrate by femtosecond laser micromachining. This technique enables high accuracy and three-dimensional capabilities, thus providing an ideal platform for developing glass-based microfluidic structures for application to plasma physics and ultrafast spectroscopy.

Philip Phenix’s (1964) book Realms of meaning started the ever growing movement concerned with how school education might help young people in their search for meaning in times of rapid social change. Today, in globalised, digital, secularised, de-traditionalised culture, the importance and urgency of this role have never been greater. Cultural change has accelerated exponentially, and for many – including students in religious/Catholic schools – traditional religious sources of meaning are no longer prominent or plausible reference points. Catholic schools, whether independent or semi-state institutions because of government funding, can make a valuable contribution young people’s spiritual/moral education, no matter what their level of religious affiliation or practice. This article argues that such a contribution requires change to the discourse or narrative of Catholic school Religious Education, with corresponding adjustments to content and pedagogy. Its present trajectory, which is excessively concerned with promoting a Catholic identity in students, needs to be modified. Both the religious and non-religious students, especially in the senior classes, would derive greater spiritual and religious benefit from the inclusion of more life-relevant and issue-related content, together with a critical, research-oriented pedagogy. Such an approach proposes that the Catholic Church’s schools should offer unconditionally a meaningful spiritual/moral education that is relevant to all students, rather than a traditional one which seemed to presume that all students are, or should be practising Catholics. This does not minimise attention to the Catholic tradition, but it allows for a study of how people negotiate the task of constructing meaning and values in a complex culture. The article also looks at the ‘headwinds’ that hinder the implementation of this approach. The article is focused specifically on the Australian context where Catholic schools are semi-state institutions because they are funded by both state and federal governments. The issues are still likely to be pertinent to Catholic education in other countries, while taking into account significant contextual differences.

As more cases of COVID-19 are studied and treated world-wide, it had become apparent that lethal and most severe cases of pneumonia are due to an out-of-control inflammatory response to the SARS-CoV2 virus. I explored the putative causes of this specific feature through a detailed genomic comparison with the closest SARS-CoV-2 relatives isolated from bats, as well as previous coronavirus strains responsible for the previous epidemics (SARS-CoV, and MERS-CoV). The high variability region of the nsp3 protein was confirmed to exhibit the most variations between closest strains. It was then studied in the context of physiological and molecular data available in the literature. A number of convergent findings point out de-mono-ADP-ribosylation (de-MARylation) of STAT1 by the SARS-CoV-2 nsp3 as a likely cause of the cytokine storm observed in the most severe cases of COVID-19. This may suggest new therapeutic approaches and an assay to predict the virulence of naturally circulating SARS-like animal coronaviruses.

Centimeter-level localization and rotation angle estimation of flatbed trucks are major problems in unmanned forklift automated loading scenes. To solve it, this study proposes a method for high-precision positioning and rotation angle estimation of flatbed trucks based on BeiDou and vision. First, an unmanned forklift equipped with a ToF camera and double antenna mobile receiver for BeiDou positioning collects depth images and localization data near the front and rear endpoints of the flatbed. Then DDRNet-23-slim was used to segment the flatbed from the depth image and extract the straight lines at the edges of the flatbed using the Hough transform and compute the set of intersection points of the lines. A neighborhood feature vector was designed to locate the endpoint of a flatbed from a set of intersection points by feature screening. Finally, the relative coordinates of the endpoints were converted to a customized forklift navigation coordinate system by BeiDou positioning, and rotation angle estimation was performed by the front and rear endpoints. Experiments showed that the endpoint positioning error was less than 3 cm and the rotation angle estimation error was less than 0.1°. The precision of the method meets the demand for automated flatbed truck loading by unmanned forklifts.

Due to its insensitivity to corrosion, textile CFRP (carbon fibre reinforced polymer) reinforcement enables the construction of thin-walled concrete structures such as shells, vaults and girder webs with minimal concrete cover. In contrast to tensile and flexural behaviour, strutting and compressive membrane action of cracked thin-walled carbon reinforced concrete (CRC) elements and the interaction of compressive stresses with transverse tensile loading have not yet been investigated. While for steel reinforced concrete components, extensive biaxial testing has shown a significant reduction of concrete compressive strength as a function of the lateral tensile stress (compression softening), the effect of biaxial loading on CRC structures has not been quantified yet. However, a different behaviour is expected due to different bond properties of steel and CFRP in concrete, smaller crack spacings and the tendency of the CFRP reinforced concrete for in-plane splitting. This paper presents an extensive experimental campaign for investigation of the influence of transverse tension and cracking on the compressive strength of CRC with refined measurement techniques. Based on a literature review on compressive softening behaviour and conventional test setups for steel reinforced concrete, a novel test setup was developed. The phenomenology of compression softening in CRC as well as the main factors influencing compressive membrane behaviour are highlighted. Based on the experimental findings a constitutive law for compression softening behaviour of CRC is proposed.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

Magnetorheological elastomers (MREs) are a type of smart material that can change their mechanical properties in response to external magnetic fields. These unique properties make them ideal for various applications, including vibration control, noise reduction, and shock absorption. This paper presents an approach for modeling the impact behavior of MREs. The proposed model uses a combination of exponential functions arranged in a multi-layer Preisach model to capture the nonlinear behavior of MREs under impact loads. The model is trained using particle swarm optimization (PSO) and validated using experimental data from drop impact tests conducted on MRE samples under various magnetic field strengths. The results demonstrate that the proposed model can accurately predict the impact behavior of MREs, making it a useful tool for designing MRE-based devices that require precise control of their impact response. The model's response closely matches the experimental data, with a maximum prediction error of 10% or less. Furthermore, the interpolated model's response shows good agreement with the experimental data, with a maximum percentage error of less than 8.5%.

Diopatra neapolitana (Delle Chiaje, 1841) is one of the most exploited polychaete species in European waters, particularly in Ria de Aveiro, a coastal lagoon in mainland Portugal, where the overexploitation of this resource has led to a generalized decline of local populations. In an attempt to reduce the impact of harvesting, several management actions were implemented, but, illegal poaching still fuels a parallel economy that threats the sustainable use of this marine resource. The present study evaluated the combination of fatty acid profiles and elemental fingerprints of the whole body and jaws, respectively, of D. neapolitana collected from four harvesting locations within Ria de Aveiro in order to determine if their geographic origin could be correctly assigned post-harvesting. Results showed that both fatty acid profiles and elemental fingerprints differ significantly among locations, discriminating the geographic origin with higher accuracy when combining these two natural barcodes than when employing each individually. The present work can therefore contribute for the implementation of an effective management plan for the sustainable use of this marine resource, making possible to detect if D. neapolitana was sourced from no take zones and if it was collected from the place of origin claimed by live baits traders.

The catalytic parameters describing enzyme catalysis are discussed in the context of the design of de novo enzymes. It is shown that high values of the catalytic efficiency may in some cases reflect tight substrate binding and lead to an immediate levelling-off of rates to reach a low plateau, an undesirable scenario for many industrial applications. It is argued that increasing the catalytic rate constant should be a main target in de novo enzyme engineering.

The fluid flow field at the upper airways is highly complex due to the complex structure of the airway. The inhaled particle flow, the air streamline and the interaction of the continuum and discrete phase could significantly affect the transport behaviour of the inhaled particles. A range of analytical, mathematical and computational fluid dynamics (CFD) models analyzed the airflow and particle transport in different idealized and asymmetric airway models. A precise understanding of the continuum and discrete phase interaction in realistic human airways is missing, and this study aims to develop a CFD-DEM model for particle transport in realistic airways. This study uses the CFD model for the continuum phase and the discrete element method (DEM) for the discrete phase. A soft sphere approach is used for the interaction of the discrete phase. Proper validation is performed for particle transport efficiency. The CFD-DEM model analyzed the particle transport in an idealized and realistic airway model, and different methods are used to analyze the transport behaviour. During the particle-particle interaction, a stagnation point and a high-pressure zone are observed at the airway model's carinal angle. The numerical results report higher deposition efficiency (DE) for particle-particle interaction than without interaction. The flow field becomes highly complex with the spring constant values, and higher DE is found for high spring constant values. The spring dashpot friction-dshf method shows higher deposition at the upper part of the airways than other interaction methods. The findings of this study and more case-specific analysis would improve the knowledge of aerosol transport in airways and the health risk assessment of the patient.

Alkaloids are the most diversified nitrogen-containing secondary metabolites having antioxi-dant, and antimicrobial properties and are extensively used in pharmaceuticals to treat different types of cancer. Nicotiana serves as a reservoir of anticancer alkaloids and is also used as a model plant for the de novo synthesis of various anti-cancer molecules through genetic engineering. Up to 4% of the total dry weight of Nicotiana was found to be composed of alkaloids where nicotine, nornicotine, anatabine, and anabasine are reported as the dominant alkaloids. And, among the alkaloids present in Nicotiana, β-carboline (Harmane and Norharmane), Kynurenines are found to show anti-tumor effects, especially in the case of colon and breast cancer. Creating new or shunting of existing biosynthesis pathways in different species of Nicotiana resulted in de novo or increased synthesis of different anti-tumor molecules or their derivatives or precursors includ-ing Taxadiane (~22.5 µg/g), Artemisinin (~120 μg/g), Parthenolide (~2.05 ng/g), Costunolide (~60 ng/g), Etoposide (~1 mg/g), Crocin (~400 µg/g), Catharanthine (~60 ng/g), Tabersonine (~10 ng/g), Strictosidine (~0.23 mg/g), etc. Enrich precursor pool especially Dimethylallyl Diphos-phate (DMAPP) and down-regulating of other bi-product pathways, compartmentalization or metabolic shunting, or organelle-specific reconstitution of the precursor pool might trigger the enhanced accumulation of the targeted anticancer alkaloid in Nicotiana.

QTc interval measurement is a widely used screening tool to assess the risk of cardiac diseases, arrhythmias, and is a useful biomarker for pharmacovigilance. However, interpretation of QTc is difficult in neonates due to hemodynamic maturational changes and uncertainties on reference values. To describe trends in QTc values throughout infancy (1 year of life), and to explore the impact of (non)-maturational changes and medicines exposure, a structured systematic review (PROSPERO CRD42022302296) was performed. In term neonates, a decrease was observed over the first week of life, whereafter values increased until two months of age, followed by a progressive decrease until six months. A similar pattern, with longer QTc values was observed in preterms. QTc is influenced by cord clamping, hemodynamic changes, therapeutic hypothermia, illnesses and sleep, not by sex. Cisapride, domperidone and doxapram result in QTc prolongation in neo-nates. Further research in this age category is needed to improve primary screening practices, earlier detection of risk factors and precision pharmacovigilance.

The genus Rhodotorula includes basidiomycetous oleaginous yeast species. R. babjevae can produce compounds of biotechnological interest such as lipids, carotenoids and biosurfactants from low value substrates such as lignocellulose hydrolysate. High-quality genome assemblies are needed to develop genetic tools and to understand fungal evolution and genetics. Here, we combined short- and long-read sequencing to resolve the genomes of two R. babjevae strains, CBS 7808 (type strain) and DBVPG 8058 at chromosomal level. Both genomes have a size of 21 Mbp and a GC content of 68.2%. Allele frequency analysis indicated tetraploidy in both strains. They harbor 21 putative chromosomes with sizes ranging from 0.4 to 2.4 Mb. In both assemblies, the mitochondrial genome was recovered in a single contig, which shared 97% pairwise identity. The pairwise identity between the majority of chromosomes ranges from 82% to 87%. We found indications for strain-specific extrachromosomal endogenous DNA. 7,591 protein-coding genes and 7,607 associated transcripts were annotated in CBS 7808 and 7,481 protein-coding genes and 7,516 associated transcripts in DBVPG 8058. CBS 7808 has accumulated a higher number of tandem duplications than DBVPG 8058. We identified large translocation events between putative chromosomes and a high genetic divergence between the two strains.

Docking the tail of lambs is a standard husbandry procedure and is achieved through several techniques including clamps, hot or cold knives and latex rings, the last of which is the most popular. All tail docking methods cause acute pain which can be reduced by application of local anesthetic, however precise anatomical injection for optimal efficacy requires considerable skill. This pen trial evaluated the ability of local anesthetic delivered with a dual function ring applicator / injector to alleviate acute tail docking pain. Thirty ewe lambs were assigned to one of three treatment groups (n = 10 per group): ring plus local anesthetic (Ring LA), ring only (Ring) and sham handled control (Sham). Lambs were videoed and behavior categorized every 5 minutes for the first hour and every 10 min for the subsequent 2 hours after treatment. There was a significant effect (p &lt; 0.001) of treatment on total active pain related behaviors in the first hour, with Ring lambs showing higher counts compared to Ring LA or Sham. Ring lambs also displayed a significantly higher count of combined abnormal postures (p &lt; 0.001) than Ring LA or Sham lambs. Delivery of 1.5ml of 2% lignocaine via the dual action device abolished abnormal behaviors and signs of pain in Ring LA lambs. However, lambs in the Ring LA group spent less time attempting to suckle compared to Ring and Sham lambs, suggesting that some residual discomfort remained.

Currently, with a large number of fatality rates, coronavirus disease-2019 (COVID-19) has emerged as a potential threat to human health worldwide. It has been well-known that severe acute respiratory syndrome-coronavirus-2 (SARS-CoV-2) is responsible for COVID-19 and World Health Organization (WHO) proclaimed the contagious disease as a global pandemic. Researchers from different parts of the world amalgamate together inquest of remedies for this deadly virus. Recently, it has been demonstrated that the spike glycoprotein (SGP) of SARS-CoV-2 is the mediator behind the entrance into the host cells. Our group has comprehensibly analyzed the SGP of SARS-CoV-2 through multiple sequence analysis along with the phylogenetic analysis. Further, this research work predicted the most immunogenic epitopes for both B-cell and T-cell. Notably, we focused mainly on major histocompatibility complex (MHC) class I potential peptides and predicted two epitopes; WTAGAAAYY and GAAAYYVGY, that bind with the MHC class I alleles which are further validated by molecular docking analysis. Furthermore, this study also proposed that the selected epitopes were shown availability in a greater range of the population. Hence, our study comes up with a strong base for the implementation of designing novel vaccine candidates against SARS-CoV-2, however adequate laboratory works will need to be conducted for the appropriate application.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

Electrification of society, increasing renewable energy sources and mobility charging lead to new loading patterns for power transformers. Dynamic load conditions induce enhanced mechanical stress on the transformers’ windings, potentially causing degradation of the solid insulation over time and compromising the transformer's short-circuit withstand capability. Thermal expansion of the windings, caused by losses in the copper conductors, occurring as the transformer is load-ed, increases the stress. Conversely, magnetic losses in the core and tie plate expansion contribute to a reduction in stress. This paper presents the effect of step changes in core losses and copper losses by on-line measurements of the clamping pressure, to better understand the mechanical stresses acting upon the solid insulation cellulose materials.

A maxillary totally edentulism was rehabilitated with one-piece implants starting from pre-existing totally removable denture. A 3D digital scan of the removable denture and upper and lower arches was performed. On this basis, a prototype with optimal esthetic and functional outcomes was re-alized and turned into a custom-made radiological stent with markers. The superimposition of STL and DICOM files allowed the virtual planning of one-piece implants ideal position. The stackable templates composed of a fixed component, namely base template, and removable components, were realized. The fixed component, once secured with anchor pins to the bone, was no longer removed. The removable components, screwed to the fixed component, were used to perform the implant surgery and the immediate prosthetic loading. A base template allowed for maintaining a fixed reference during the entire workflow, improving the transition between the digital project, the surgical procedure, and the prosthetic rehabilitation.

In voice analysis, the electroglottographic (EGG) signal has long been recognized as a useful complement to the acoustic signal, if only when the vocal folds are actually contacting, such that this signal has an appreciable amplitude. However, phonation can occur also without vocal fold contacting, as in breathy voice, in which case the EGG amplitude is low, but not zero. It is of great interest to identify the transition from non-contacting to contacting, because this will substantially change the nature of the vocal fold oscillations; yet that transition is not in itself audible. The magnitude of the normalized peak derivative of the EGG signal is a convenient indicator of contacting, but no current EGG hardware has a sufficient signal-to-noise ratio of the derivative. The textbook techniques of spectral thresholding and static notch filtering are straightforward to implement, can run in real time, and can mitigate several noise problems in EGG hardware.

Cornelia de Lange syndrome (CdLS) is a complex genetic disorder with a distinct set of facial features, growth limitations, and limb anomalies. Its clinical spectrum is broad and presents significant challenges in pediatric diagnosis and management. The variable presentation of the disorder, due to cohesin complex mutations, requires extensive research to refine care and improve outcomes. This article provides a case series review of pediatric CdLS patients, alongside a comprehensive literature review, exploring clinical variability and the relationship between genotypic changes and phenotypic outcomes. It also discusses the evolution of diagnostic and therapeutic techniques, with an emphasis on innovations in genetic testing, including the detection of mosaicism and novel genetic variations. The aim is to synthesise case studies with current research to advance our understanding of CdLS and the effectiveness of management strategies in pediatric healthcare. This work highlights the need for an integrated, evidence-based approach to diagnosis and treatment, and aims to fill existing research gaps and advocate for holistic care protocols and tailored treatment plans for CdLS patients, ultimately improving their quality of life.

The state of Veracruz has ample water resources. However, due to population and industrial growth, there has been an increase in the discharge of wastewater into surface water bodies. To analyze the water quality in the Bobos River, Veracruz, and its sustainability, researchers collected nine samples from nine different points in the reservoir. They measured various parameters such as temperature, pH, dissolved oxygen, conductivity, total nitrogen, nitrate, chemical oxygen demand, total phosphorus, phosphate, dissolved solids, and fecal coliforms. The results showed that the river's water quality is at risk. The concentration of pollutants such as chemical oxygen demand and fecal coliforms is high. Conductivity values ranged from 0.26 to 3.81 mS. If preventive and corrective measures are not taken, the river's ability to purify pollutants will be severely compromised. This study evaluates the physical, chemical, and microbiological characteristics of the water in Bobos River. It specifically investigates the influence of the nearby citrus industry on the river's water quality. The study also aims to promote environmental sustainability.

Current consensus diagnostic criteria for vestibular migraine (VM) describes this as an episodic disorder. However, a minority of patients report prolonged (>72h duration) or even persistent VM symptoms, prompting whether a chronic variant of vestibular migraine (CVM) should be introduced to the current classification and how best to define it. Here we summarize current evidence of such a potential chronic variant of VM and critically review previously published proposed definitions for CVM. Potential approaches to establish a diagnostic framework for CVM include a) following the distinction between episodic and chronic migraine headaches; namely, frequent and/or prolonged episodes of VM (but not persistent vertigo or dizziness) in the context of chronic migraine headaches or b) daily dizzy spells over more than 6 months that responded well to prophylactic anti-migraine therapy. A key challenge when defining diagnostic criteria for CVM is how to distinguish it from other chronic vestibular syndromes such as motion sickness, persistent postural-perceptual dizziness (PPPD), and mal-de-débarquement syndrome. Indeed, more than 50% of patients with PPPD and up to 46% with mal-de-débarquement syndrome fulfill diagnostic criteria for episodic migraine headaches, suggesting these disorders may all lie along a spectrum. We propose that when VM becomes persistent, it is best classified as PPPD but that VM and PPPD are not mutually exclusive, such that patients with PPPD need not have features of VM and the triggering event for persistent dizziness may be independent of migraine.

In this study we investigate the formation of dynamical energy cascades in higher order KdV-type equations. In the beginning we recall what is known about the dynamic cascades for the classical KdV (quadratic) and mKdV (cubic) equations. Then, we investigate further the mKdV case by considering a richer set of initial perturbations in order to check the validity and persistence of various facts previously established for the narrow-banded perturbations. Afterwards we focus on higher order nonlinearities (quartic and quintic) which are found to be quite different in many respects from the mKdV equation. Throughout this study we consider both the direct and double energy cascades. It was found that the dynamic cascade is always formed, but its formation is not necessarily accompanied by the nonlinear stage of the modulational instability. Direct cascade structure remains invariant regardless the size of the spectral domain. In contrast, the double cascade shape can depend on the size of the spectral domain, even if the total number of cascading modes remains invariant. Results obtained in this study can be potentially applied to plasmas, free surface and internal wave hydrodynamics.

In this study, we investigate the formation of dynamical energy cascades in higher-order KdV-type equations. In the beginning, we recall what is known about the dynamic cascades for the classical KdV (quadratic) and mKdV (cubic) equations. Then, we investigate further the mKdV case by considering a richer set of initial perturbations in order to check the validity and persistence of various facts previously established for the narrow-banded perturbations. Afterwards, we focus on higher-order nonlinearities (quartic and quintic) which are found to be quite different in many respects from the mKdV equation. Throughout this study, we consider both the direct and double energy cascades. It was found that the dynamic cascade is always formed, but its formation is not necessarily accompanied by the nonlinear stage of the modulational instability. Direct cascade structure remains invariant regardless of the size of the spectral domain. In contrast, the double cascade shape can depend on the size of the spectral domain, even if the total number of cascading modes remains invariant. Results obtained in this study can be potentially applied to plasmas, free surface and internal wave hydrodynamics.

There is crescent demand for knowledge improvement of the integrated water vapor (IWV) distribution in regions affected by heat islands that are associated with extreme rainfall events such as in the metropolitan area of Rio de Janeiro (MARJ). This work assessed the suitability and distribution of IWV in the MARJ using products from the Global Navigation Satellite Systems (GNSS), MODerate Resolution Imaging Spectroradiometer (MODIS), and radiosonde. GNSS data were collected by the tracking station named RDJN, from the cooperation of the International GNSS Monitoring and Assessment System (iGMAS) and the National Observatory of Brazil (Observatório Nacional - ON), and the tracking stations ONRJ, RIOD, and RJCG belonging to the Brazilian Network for Continuous Monitoring (RBMC) in the period of January 2015–August 2018. High variability of the near surface air temperature (T) and relative humidity (RH) were observed among eight meteorological sites considered. The mean T differences between sites, up to 4.4 °C, led to mean differences as high as 3.1 K for weighted mean temperature (Tm) and hence 0.83 mm for IWV differences. The performance of the MODIS MOD07 and MYD07 products provided a reasonably good representation of the mean spatial distribution of IWV, especially during the daylight passages of the satellites TERRA and AQUA. Local grid points of MODIS IWV estimates had relatively good agreement with the GNSS-derived IWV, with mean differences from -2.4–1.1 mm considering only daytime passages of the satellites TERRA and AQUA. During nighttime, MODIS underestimated IWV (from -9–-3 mm) with respect to GNSS, due to attenuation of IR radiation by clouds. A contrasting behavior was found in the radiosonde IWV estimates compared with the estimates from GNSS. There were dry biases of 1.4 mm (3.7% lower than expected) by radiosonde IWV during the daytime considering that all other estimates were unbiased and the differences between IWV GNSS and IWV RADS were consistent. Based on the IWV comparisons between radiosonde and GNSS at nighttime, the atmosphere over the radiosonde site is about 1.2 (2.3) mm wetter than over RIOD (RDJN) station. The long time series of the comparisons between IWVRDJN and IWVRIOD showed that the highest values of IWV occurred from the afternoon to nocturnal hours. Further, the atmosphere over the site RIOD was consistently about 1 mm wetter than over RDJN. These results showed the feasibility of the iGMAS RDJN station data compared with the RBMC, MODIS, and radiosonde data to investigate IWV in a region with occurrence of heat islands, and the peculiar physiographic and meteorological characteristics as in the MARJ. This work recommended the usage of complete meteorological station data collocated near every GNSS receiver aiming improvements of local GNSS IWV estimates and serving as additional support for operational numerical assimilation, weather forecast, and nowcast of extreme rainfall events.

The study presents an efficient computational investigation on the behaviour of the direct-drive system integrated into the offshore 5MW NREL wind turbine model under demanding aerodynamic loading conditions with the aim of optimising and developing more sustainable key structural components. The research was based on computational simulation packages to verify the use of real-world wind data, the loading conditions on the blade structures through aero-elastic simulation studies, as well as analyse the behaviour of the drive system. Through the application of validated aerodynamic loading conditions, resulting normal forces on the blades structure were obtained and applied to a dedicated simplified model that was also previously validated, to estimate the transferred loads into the powertrain. The adopted methodology allowed for the identification of shaft misalignment induced air-gap eccentricity. The impact of shaft deflections on resulting magnetomotive force was considered by making use of the Maxwell stress distribution expression. By taking into account the resulting loading cases on the generator structure, as well as the inherent typical loads generated by the electrical machine, a procedure including structural parametric and topology optimisation was developed and performed, achieving a rotor mass reduction between 8.5 and 9.6% if compared with the original model.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.

Currently, there is no widely accepted consensus regarding a consistent thermodynamic framework within the special relativity paradigm. However, by postulating that the inverse temperature 4-vector, denoted as β, is future-directed and timelike, intriguing insights emerge. Specifically, it is demonstrated that the q-dependent Tsallis distribution can be conceptualized as a de-Sitterian deformation of the relativistic Maxwell-Jüttner distribution. In this context, the curvature of the de Sitter space-time is characterized by Λ/3, where Λ represents the cosmological constant within the ΛCDM standard model for Cosmology. For a simple gas composed of particles with proper mass m, and within the framework of quantum statistical de Sitterian considerations, the Tsallis parameter q exhibits a dependence on the cosmological constant given by q=1+ℓcΛ/n where ℓc=ℏ/mc is the Compton length of the particle and n is a positive numerical factor. This formulation establishes a novel connection between the Tsallis distribution, quantum statistics, and the cosmological constant, shedding light on the intricate interplay between relativistic thermodynamics and fundamental cosmological parameters.

De-escalation is currently taking place both in surgical and systemic treatment of breast cancer. The introduction of trastuzumab, the first monoclonal antibody against the HER2 receptor over 20 years ago was a milestone in the treatment of HER2 positive breast cancer and marked the beginning of a new era in targeted tumor therapy. In the sense of de-escalation, omitting non-targeted cytotoxic chemotherapy altogether is often hailed as the ultimate goal of oncological research. Especially in case of small, node-negative, HER2 positive early breast cancer, it remains a challenge for clinicians to establish the safest and most efficient treatment plan while considering the significant potential for toxic side effects associated with chemotherapy and HER2 targeted therapy, and the generally excellent prognosis. In this context, several ongoing studies are currently assessing chemotherapy-free regimens as part of strategies aimed at de-escalating therapy in the field of HER2 positive early breast cancer. Despite promising early results from these studies, combination of anti-HER2 treatment with chemotherapy backbone remains standard of care.

This study analyzes the influence of CEO types on corporate governance, focusing on de facto (substantial) CEOs. We examine how substantial CEOs impact ESG activities (Hypothesis 1) and corporate value (Hypothesis 2). Data were collected from KIS-VALUE and DART (Electronic Disclosure System) of the Financial Supervisory Service, defining substantial CEOs as highest remuneration recipients exceeding the representative director of the company pay. Results sup-port Hypothesis 1, showing companies with substantial CEOs are more engaged in ESG activities, potentially to improve public image while concealing self-serving behaviors. Hypothesis 2 is validated, indicating lower corporate value in companies with substantial CEOs due to prioritizing personal interests over long-term profit maximization. Despite limitations in exploring governance relationships beyond remuneration data, the study offers key contributions. It expands research on corporate governance and ESG activities by identifying substantial CEOs through objective remuneration data. It highlights the importance of an independent board for transparent governance and positive corporate value. Lastly, empirical evidence shows the negative impact of misdirected ESG activities on corporate value. By using remuneration as an indicator, this study illuminates substantial CEOs' influence on corporate value and ESG activities, providing insights for future research in corporate governance and ESG.

To assess the degree to which it has met its commitments under the Paris Agreement, Morocco is called upon to carry out carbon assessments and transparent evaluations. Within the forestry sector, little is known about the role of Morocco’s forests in contributing to carbon uptake. With this aim, we applied for the first time in literature the 3-PG model to Cedrus atlantica ((Endl.) Manetti ex Carrière, 1855), which represents about 131.800 ha of Morocco’s forest area (i.e. Azrou forest). Through the Differential Evolution - Markov Chains (DE-MC) we tested and assessed the sensitivity and calibrated the 3-PG model. This process-based model provided significant results regarding the carbon sequestration capacity. The results showed the following: i- Parameters related to stand properties, canopy structure, and processes, as well as biomass partitioning, are the most important or sensitive for the performance of the model; ii- The DE-MC method optimized the values of the 3-PG parameters which was confirmed by the means of Gelman-Rubin convergence test; iii- According to the predictions of the calibrated 3-PG, the Net Primary Production in the pure Azrou forest varies between 0.32 and 7.88 tC.ha−1.yr−1, it is equal in average to 4.9 tC.ha−1.yr−1, which given the total area corresponds to 7078 tC.yr−1.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

The issue of being pro-gender is still a controversial topic to be debated in Indonesian society. However, in the 21st Century, many women have been able to break through barriers and participate in the public sphere. It is a form of self-existence as proposed by Simone de Beauvoir on existentialist feminism. Based on these problems, this study aims to find out and answer questions about how Indonesian women exist in the public sphere in the 21st Century and find out how Indonesian women exist in the public sphere through Simone de Beauvoir's existentialist feminism paradigm. The research method used is descriptive-qualitative through a literature review of 23 journal articles, websites, and data reports with a range of 2019-2021. This study found that based on Simone de Beauvoir's feminist paradigm, Indonesian women in the 21st Century are no longer a figure other than complete. Furthermore, the data collected by the researcher shows that several gender indicators have shown that Indonesian women have been able to occupy public spaces in various aspects. Based on these results, it is hoped that it can provide information about Simone de Beauvoir's existentialist feminism thought and its relevance to the existence of Indonesian women in the public sphere in the 21st Century. However, this research has limitations, those are only about women in Indonesia, and the paradigm of feminism is limited to Simone de Beauvoir's existentialist feminism.

In this paper we will show that standard physics to a large degree consists of derivatives of a deeper reality. This means standard physics is both overly complex and also incomplete. Modern physics has typically started from working with first understanding the surface of the world, that is typically the macroscopic world, and then forming theories about the atomic and subatomic world. And we did not have much of a choice, as the subatomic world is very hard to observe directly, if not impossible to observe directly at the deepest level. Despite the enormous success of modern physics, it is therefore no big surprise that we at some point have possibly taken a step in the wrong direction. We will claim that one such step came when one thought that the de Broglie wavelength represented a real matter wavelength. We will claim that the Compton wavelength is the real matter wavelength. Based on such a view we will see that many equations in modern physics are only derivatives of much simpler relations. Second, we will claim that in today’s physics one uses two different mass definitions, one mass definition that is complete or at least more complete, embedded in gravity equations without being aware of it, as it is concealed in GM, and the standard, but incomplete, kg mass definition in non-gravitational physics. First, when this is understood, and one uses the more complete mass definition that is embedded in gravity physics, not only in gravity physics, but in all of physics, then one has a chance to unify gravity and quantum mechanics. Our new theory shows that most physical phenomena when observed over a very short timescale are probabilistic for masses smaller than a Planck mass and dominated by determinism at or above Planck mass size. Our findings have many implications. For example, we show that the Heisenberg uncertainty principle is rooted in a foundation not valid for rest-mass particles, so the Heisenberg uncertainty principle can say nothing about rest-masses. When re-formulated based on a foundation compatible with a new momentum that is also compatible with rest-masses, we obtain a re-defined Heisenberg principle that seems to become a certainty principle in the special case of a Planck mass particle. Furthermore, we show that the Planck mass particle is linked to gravity and that we can easily detect the Planck scale from gravity observations. The Planck mass particle is unique as it only lasts the Planck time, and in that very short time period it can only be observed directly from itself, and it therefore closely linked to absolute rest.

Most shear tests are performed as standard three- or four-point bending tests, i.e., on one-way simply supported specimens subjected to concentrated loads. The major disadvantage is that these conditions usually do not correspond to the support and load condition of real structures. Structural members such as beams or slabs, are often multi-span components and subjected to distributed loads. As a consequence, the complex shear behavior, including crack kinematics, shear transfer mechanisms, and shear capacity, is studied almost only simply supported members with concentrated load. Positive impacts on the shear behavior resulting from continuous systems and distributed loads are thus neglected in the derivation of calculation models and in the development of design specifications. To incorporate the effect of continuous members and distributed loading conditions, more experimental investigations are necessary. Therefore, a total of 16 bending shear tests on CFRP reinforced concrete members without shear reinforcement were carried out. The tests specimens were tested as simply supported beams or as simply supported beams with loaded cantilever to simulate the continuous system with concentrated and distributed loads. Furthermore, the shear slenderness was varied by using different span lengths and degrees of restraint in the systems with intermediate support. All test specimens were made of high-strength concrete and were reinforced with a multilayer grid-like CFRP reinforcement in longitudinal direction. There was no shear reinforcement installed in the investigated shear span. This paper focuses the influence of the support conditions and load arrangements on crack development as well as on shear strength.

This study deals with the computational analysis of the kinetic processes of a microbial electrolysis cell assisted-anaerobic digestion (MEC-AD) treating raw-waste activated sludge (WAS), comparatively with a conventional AD, as well as the effect of the Organic Loading Rate (OLR) on the system’s performance. The aim was to derive a single kinetic and mathematical model for the study of the MEC-AD, using the ADM1 framework, which can be utilized to extract the effect of an applied potential on the kinetics of AD. The experimental data were obtained from the long-term, continuous operation of two identical reactors (an AD and a MEC-AD), which were operated at different OLRs (1.1, 1.7 and 2.9 gCOD/(L*d)). The results showed that the MEC-AD yielded improved biomass yields, substrate consumption kinetics and 1st order disintegration kinetics, with a predominant contribution to disintegration of complex particulates, comparatively with the AD. Moreover, it enabled operation at higher OLRs (achieving the highest divergence from the AD at the OLR of 4.14 gCOD/(L*d)), therefore accelerating sludge treatment, as well as an improved performance at an increased solids retention time (SRT). These findings can serve as a quantitative guide for the effects of the operating parameters on the raw-WAS-fed MEC-AD performance.