With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

Seasonal oscillations in the partial pressure of carbon dioxide (pCO2) in the Earth’s atmosphere stronger in northern latitudes are assumed to show that terrestrial photosynthesis exceeds respiration in summer reducing the pCO2, but increasing in winter when respiration exceeds photosynthesis. We disagree, proposing that variations in the temperature of the surface mixing zone of seawater also regulate the atmospheric pCO2, thermodynamically. We show that carbonate (CO32-) concentrations will therefore increase in summer with CaCO3 (calcite or aragonite) becoming less soluble, so calcium and carbonate ions are predicted to aggregate more while CO2 concentration falls in warmer seawater, thermodynamically favoring lower atmospheric pCO2. In winter, these physical processes are reversed, redissolving suspended calcite thus increasing carbonate alkalinity; carbonate concentration lessens as bicarbonate and soluble CO2 increase, raising the pCO2 in air. Our numerical computation shows that thermal fluctuations in equilibria favor absorption from air of more than one mole of CO2 per square meter in summer, coinciding with calcite formation maximizing in warmer water, potentially augmenting limestone reefs if there is a trend for increasing temperature . Another assumption we challenge is that upwelling from deeper water is the sole cause of increases in dissolved inorganic carbon (DIC) and alkalinity in surface waters, particularly in the southern hemisphere. Instead, calcite dissolution is favored as water temperature falls near the surface. It is well established that the seasonal summer decline in atmospheric CO2 coincides in fertile seawater with higher rates of biotic calcification and acidity, allowing increased CO2 capture by photosynthesis. However, its reversal in winter is proposed to be also a result of the cyclic dissolution of calcite as temperature falls, facilitated by biogenic respiration now exceeding photosynthesis; this can mutually provide the CO2 needed to convert carbonate ion alkalinity from calcite dissolution with bicarbonate increasing. Physical reasons why this oscillation is more obvious in the northern hemisphere include greater seasonal variations in water temperature (ca. 7.1 oC) being almost twice that in the cooler southern hemisphere (ca. 4.7 oC) and the greater depth of the surface mixing zone of seawater in the southern oceans. Evidence from 13CO2 fluxes between surface seawater and air is also assessed to test this hypothesis but questions remain regarding the regional rates of inorganic precipitation and dissolution of CaCO3 in the mixing zone. In summary, rapid biogenic calcification is favored by summer photosynthesis, but slower abiogenic calcification is more likely in warmer water.

A high perovskite activity is sought for use in magnetic applications. In this paper, we present the simple synthesis of (2.5 and 5%) Tellurium-impregnated-LaCoO3 (Te-LCO), Te and LaCoO3 (LCO) by using a ball mill, chemical reduction, and hydrothermal synthesis, respectively. We also explored the structure stability along with the magnetic properties of Te-LCO. Te has a rhombohedral crystal structure, whereas Te-LCO has a hexagonal crystal system. The reconstructed Te was imbued with LCO that was produced by hydrothermal synthesis; as the concentration of the imbuing agent grew, the material became magnetically preferred. According to the X-ray photoelectron spectra, the oxidation state of the cobaltite is one that is magnetically advantageous. As a result of the fact that the creation of oxygen-deficient perovskites has been shown to influence the mixed (Te4+/2-) valence state of the incorporated samples, it is abundantly obvious that this process is of utmost significance. The TEM image confirms the inclusion of Te in LCO. The samples start out in a paramagnetic state (LCO), but when Te is added to the mixture, the magnetic state shifts to a weak ferromagnetic one. It is at this point that hysteresis occurs due to the presence of Te. Despite being doped with Mn in our prior study, rhombohedral LCO retains its paramagnetic characteristic at room temperature (RT). As a result, the purpose of this study was to determine the impacts of RT field dependency of magnetization (M-H) for Te-impregnated LCO in order to improve the magnetic properties of RT because it is a low-cost material for advanced multi-functional and energy applications.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

This study scrutinizes the complexities of designing and exploring the potential energy surface (PES) of systems containing more than twenty atoms with planar tetracoordinate carbons (ptCs). To tackle this issue, we utilized an established design rule to design a Naphtho [1,2-b:4,3-b′:5,6-b′′:8,7-b′′′]tetrathiophene derivative computationally. This process began with substituting S atoms with CH– units, then replacing three sequential protons with two Si2+ units in the resultant polycyclic aromatic hydrocarbon polyanion. Despite not representing the global minimum, the newly designed Si8C22 system with four ptCs provided valuable insights into strategic design and PES exploration. Our results underscore the importance of employing adequate methodologies to confirm the stability of newly designed molecular structures containing planar hypercoordinate carbons.

2,5-Di(hydroxymethyl)furan (DHMF) is a high-value chemical block than can be synthesized from 5-hydroxymethylfurfural (HMF), a platform chemical that results from the dehydration of biomass-derived carbohydrates. In this work, the HMF biotransformation capability of different Fusarium species was evaluated and F. striatum was selected to produce DHMF. The effects of the inoculum size, glucose concentration and pH of the media over DHMF production were evalu-ated by a 23 factorial design. A substrate feeding approach was found suitable to overcome the toxicity effect of HMF towards the cells when added at high concentrations (>75 mM). The pro-cess was successfully scaled-up at bioreactor scale (1.3 L) with excellent DHMF production yields (95%) and selectivities (98%). DHMF was purified from the reaction media with high recovery and purity by organic solvent extraction with ethyl acetate.

Cholesterol siRNA conjugates attract attention because they allow the delivery of siRNA into cells without the use of transfection agents. In this study, we compared the efficacy and duration of silencing induced by cholesterol conjugates of selectively and totally modified siRNAs and their heteroduplexes of the same sequence and explored the impact of linker length between the 3' end of the sense strand of siRNA and cholesterol on the silencing activity of “light” and “heavy” modified siRNAs. All 3'-cholesterol conjugates were equally active under transfection, but the conjugate with a C3 linker was less active than those with longer linkers (C8 and C15) in a carrier-free mode. At the same time, they are significantly inferior in activity to the 5'-cholesterol conjugate. Shortening the sense strand carrying cholesterol by 2 nucleotides from the 3'-end did not have a significant effect on the activity of the conjugate. Replacing the antisense strand or both strands with fully modified ones has a significant effect on silencing as well as improving the duration in transfection-mediated and carrier-free modes. A significant 78% suppression of MDR1 gene expression in KB-8-5 xenograft tumors developed in mice promises an advantage from the use of fully modified siRNA cholesterol conjugates in combination chemotherapy.

Inflammatory diseases are common pathological processes caused by various acute and chronic factors and some of them are autoimmune diseases. Exosomes are fundamental extracellular vesicles secreted by almost all cells, which contain a series of constituents, i.e. cytoskeletal and cytosolic proteins (actin, tubulin, histones), nucleic acids (mRNA, miRNA, DNA), lipids (diacylglycerophosphates, cholesterol, sphingomyelin, ceramide), and other bioactive components (cytokines, signal transduction proteins, enzymes, antigen presentation and membrane transport/fusion molecules, adhesion molecules). This review would be a synopsis of the actual knowledge on the contribution of exosomes from different cell sources as possible therapeutic agents against inflammation, focusing on several inflammatory diseases, neurological diseases, rheumatoid arthritis and osteoarthritis, intestinal bowel disease, asthma, liver and kidney injuries. Current knowledge indicates that the role of exosomes in therapy of inflammation and in inflammatory diseases could be distinctive. Main limitations to their clinical translation are still production, isolation, and storage. Additionally, there is an urgent need to personalize the treatments in terms of selection of exosomes, their dosages and routes of administration, and a deeper knowledge about their biodistribution, type and incidence of adverse events and long-term effects of exosomes. In conclusion, exosomes can very promising next generation therapeutic option, superior to synthetic nanocarriers and cell therapy, and can represent a new strategy of effective, safe, versatile and selective delivery systems in the future.

Phase imaging of biochemical samples has been demonstrated for the first time at the Infrared Microspectroscopy (IRM) beamline of the Australian Synchrotron using the usually discarded Near-IR (NIR) region of the synchrotron-IR beam. The synchrotron-IR beam at the Australian Synchrotron IRM beamline has a unique fork shaped intensity distribution as a result of the gold coated extraction mirror shape, which includes a central slit for rejection of the intense X-ray beam. The resulting beam configuration makes any imaging task challenging. For intensity imaging, the fork shaped beam is usually tightly focused to a point on the sample plane followed by a pixel-by-pixel scanning approach to record the image. In this study, a pinhole was aligned with one of the lobes of the fork shaped beam and the Airy diffraction pattern was used to illuminate biochemical samples. The diffracted light from the samples was captured using a NIR sensitive lensless camera. A rapid phase-retrieval algorithm was applied to the recorded intensity distributions to reconstruct the phase information corresponding to different planes. The preliminary results are promising to develop multimodal imaging capabilities at the IRM beamline of the Australian Synchrotron.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

The role of chemical communication in social relationships of birds is receiving growing attention but our knowledge is still scarce compared to other taxa. Previous evidence suggests that chemical cues emitted by birds may carry information about their characteristics that may be useful in a sexual selection context. However, experimental studies are needed to investigate the role of bird chemical cues in signalling quality of potential partners. We performed an experimental study aimed to disentangle whether female zebra finches, Taeniopygia guttata, use chemical cues to assess the body condition and body size of potential partners. We offered focal females the scent of two males differing in body condition and body size. Our results show that females can assess the body condition of potential partners using olfaction. However, contrary to expected in a mate choice context, our results show that females avoided the scent of the male with greater body condition and body size. Our results therefore suggest that, despite performing the study during breeding period, social interactions may be mediating the avoidance of the scent of the conspecific of the opposite sex with better body condition and body size in this gregarious species.

Microbial biofilms cause several environmental and industrial issues, even on the human health. Although they have represented a threaten due to their resistance to antibiotics, there are currently no approved antibiofilm agents for clinical treatments. The multi-functionality of antimicrobial peptides (AMPs) including the antibiofilm activity and their potentialities to target multiple mi-crobes motivated the synthesis of AMP relatives for developing antibiofilm agents for clinical purposes. Antibiofilm peptides (ABFPs) have been organized in databases that allowed the building of prediction tools which have assisted in the discovery/design of new antibiofilm agents. However, the complex network approach has been explored yet as an assistant tool for this aim. Herein, a kind of similarity networks, called the Half-Space Proximal Network (HSPN) is applied to represent/analyse the chemical space of the ABFPs aimed to identify promising scaf-folds for the development of next generation antimicrobials, able to target both planktonic and biofilm microbial forms. Such analyses also considered the metadata associated to the ABFPs such as origin, other activities, targets, etc. in which the relationships were projected by multilayer networks called metadata networks (METNs). From the complex networks mining, a reduced but informative set of 66 ABFPs representing the original antibiofilm space was extracted. This subset retained from the most central to atypical ABFPs, having some of them, desired properties for developing next generation antimicrobials. So, this subset is advisable for assisting the search/design both new antibiofilm/antimicrobial agents. The provided ABFP motifs list, dis-covered within the HSPN communities, is also useful for the same purpose.

A multi-methodic analysis was performed on 5 samples of fly ashes coming from different biomasses. The aim of the study was to evaluate their possible re-use and their dangerousness for men and environment. Optical granulometric analyses indicate that the average diameter of the studied fly ashes is around 20 µm, whereas only ~1 vol% has diameter lower that 2.5 µm. The chemical composition, investigated with electron probe microanalysis, indicates that all the samples have a prevalent Ca composition, followed by Si and Al. A large content in K and P was observed in some samples, whereas the content in potentially toxic elements is always below the Italian law thresholds. Polycyclic aromatic hydrocarbons are completely absent in all the samples coming from combustion plants, whereas they are present in the fly ashes from the gasification center. Quantitative mineralogical content, determined by Rietveld analysis of X-ray powder diffraction data, indicates that all the samples have a large amorphous content, likely enriched in Ca, and several K and P minerals, such as sylvite and apatite. The results obtained from the performed chemo-mineralogical study allowed to point out that the biomass fly ashes could be interesting materials (1) as amending in clayey soils, in substitution to lime, to stimulating pozzolanic reaction and improve their geotechnical properties, on the one hand, avoiding to mine raw materials and, on the other hand, re-cycling wastes; (2) as agricultural fertilizes made by a new and ecological source of K and P.

Modified structure along latent tracks and track formation process have been investigated in poly(allyl diglycol carbonate), PADC, which is well recognized as a sensitive etched track detector. This knowledge is essential to develop novel detectors with improved track registration property. The track structures of protons and heavy ions (He, C, Ne, Ar, Fe, Kr and Xe) have been examined by means of FT-IR spectrometry, covering the stopping power region between 1.2 to 12,000 eV/nm. Through a set of experiments on low-LET radiations – such as gamma ray -, multi-step damage process by electron hits was confirmed in the radiation-sensitive parts of the PADC repeat-unit. From this result, we unveiled for the first-time the layered structure in tracks, in relation with the number of secondary electrons. We also proved that etch pit was formed when at least two repeat-units were destroyed along the track radial direction. To evaluate the number of secondary electrons around tracks, a series of numerical simulations were performed with Geant4-DNA. Therefore, we are proposing new physical criterions to describe the detection thresholds. Futhermore, we propose a present issue of the definition of detection threshold for semi-relativistic C ions. And as a possible chemical criterion, formation density of hydroxyl group is suggested to express the response of PADC.

The results of physico-chemical studies of individual fruit parts, including crusts, partitions, juice and seeds themselves, extracted from immature (green), unripe and mature fruits of three harvest periods are presented: 20.VII, 01.IX and 15.X. The analyses were carried out in 2019-20 during the period of active growth and ripening of fruits in the varieties Spring, Iridanaly, Guleisha pink and wild pomegranate from the Geokchay region (Azerbaijan) using standard and generally accepted physico-chemical methods. The ripe fruit (130-288 g) consisted of 60-113% of the peel (peel together with partitions), 53-140% of the juice and 17-85% of the seeds themselves. The edible part of the ripened fruits (53.85-73.2 of the total weight of the fruit) consisted of 58.54-78.65% juice and 21.35 -41.46% seeds, fresh juice contained 15.7-17.7% solids, including 12.04-13.84% sugar, 0.17-0.30% protein, 0.15—0.23% pectin, 0.30-0.40% ash and 0.26-0.57% total polyphenols. The concentrations of solids, protein, ash and total polyphenols in the seeds themselves, remaining after the extraction of juice from the grains of ripe fruits, were 50.0-58.2, 4.13-5.75, 0.60-1.0 and 0.08-0.32%, respectively. There were fewer total polyphenols, flavonoids, chlorogenic acids, catechins and leucoanthocyanins in ripe fruits, and more ascorbic acid, anthocyanins and proanthocyanidins than in unripe ones. The period from the second half of July to the beginning of September is the time of a real “boom” of common polyphenols.

In this paper, a distinction is first made between environmental, sustainable and green chemistry; the last two are then examined in relation to the more general problem of the environmental education. A brief historical digression on the STS (Science, Technology and Society) movement tries to dissect the reasons why chemistry is seen by the general public as a problem, not as a decisive resource for the realization of the ecological transition. Although sustainable and green chemistry can be decisive in overcoming the insularity of chemical disciplines in the high school, it fails to effectively embed itself in educational practices. Specific operational goals, supporting a real scientifical and technological literacy in sustainable and green chemistry, can help chemical educators. They are provided at the end of an examination of the founding axes of sustainable and green chemistry, according to the criteria of scientific and technological literacy.

Prunus dulcis is one of the most widely cultivated species in the world. Its fruit (almond) is rich in various nutritious and bioactive compounds that exert several beneficial effects. The aim of this study was to determine the chemical profile and evaluate the biological potential in vitro of almond shell extracts. The chemical analysis of shell extracts led to the identification of 15 com-pounds by HPLC-DAD of which 11 were first detected in the almond plant. Twenty-six volatile compounds were identified by the GC-MS technique, among them; seven were firstly detected in the studied plant. For the biological activities, the extracts demonstrated moderate inhibition potential against the antioxidant, antidiabetic, and cytotoxic activities. The methanol extract at 50 µg/mL showed the highest antioxidant (45%) and antidiabetic activities (45% against alpha-glucosidase and 31% against alpha-amylase extracts), while the cyclohexane and dichloromethane at 50 µg/mL showed the highest cytotoxic activity towards Hela (32.2% with cyclohexane), and RAW 264-7 (45% with dichloromethane). Overall, these findings demonstrate the potential of almond shell extracts as a source of bioactive compounds that could be applied in the pharmaceutical and medical fields.

Multiresistant pathogens pose a serious threat to human health. The genus candida is one class of human pathogenic yeasts responsible for infections affecting healthy and immunocompromised patients. In this context, plant essential oils emerged as a future natural alternative to control the diseases caused by these pathogens. Here, it highlighted antimicrobial activity and the mechanisms of action of the essential oil extracted from Croton pluriglandulosus Carn.-Torres & Riina (CpEO) leaves on human pathogenic microorganisms in planktonic and biofilm lifestyles. In addition, for the first time, the oil composition was revealed by GC-MS analysis and the toxicity to human red blood cells (HRBC). Twenty-six chemical compounds were identified in EOCp, Elemicin, Bicyclogermacrene, caryophyllene, brevifolin and 2,4,6-trimethoxy-styrene. Through hemolytic assay, it was shown that CpEO has no toxicity to human RBCs. At the concentration of 50 μg mL-1, CpEO did not show great antibacterial potential. However, promising data were found for C. krusei and C. parapsilosis inhibiting by 89.3% and 80.7% of planktonic cell growth and 83.5% and 77.9% the biofilm formation, respectively. Furthermore, the mechanisms of action CpEO were elucidated by fluorescence. Scanning electron microscopy revealed damage to the cell membrane and pore formation, ROS overproduction, and Induction of apoptosis in candida cells. Our results reinforce the potential of CpEO as an effective alternative molecule of pharmaceutical interest.

In the production of grafted vines, losses are caused by fungal pathogens during callus forming or after planting in the soil. To control or reduce natural fungal infections in nurseries, certain applications were conducted in sapling cultivation stage to analyse the efficacy of cyprodinil + fludioxonil, floupyram + tebuconazole active substances and Trichoderma harzianum biological preparation. 1103 Paulsen rootstock and Vitis viniferea L. Sultana cultivars were stored in fungicide suspensions for 60 minutes before and after grafting in the study. After grafting, the seedlings were divided into i) cutting + sawdust ii) cutting + sawdust + soil application groups and transferred to the callus room. Fungicides were applied 1 to 7 days after the callus development to wet the seedling roots 1 to 7 days after they were planted. After nine months in the nursery, the plants were uprooted, classified as diseased or healthy, and analysed for morphological and molecular diagnosis of fungal species, isolation incidence, and seedling quality and yield. After callus development, Fusarium solani was most frequently isolated pathogen in the roots (21.5%), cyprodinil + fludioxonil reduced the Ilyonectria sp. isolation rate in both shoots and roots. Botryosphaeria obtusa and I. liriodendri pathogens were not detected in sick and healthy cyprodinil + fludioxonil-treated saplings. The highest seedling yield was observed with fludioxonil + cyprodinil, cutting + sawdust + soil (78.75%) and cutting + sawdust (70.68%) applications. According to the results of this study, it was found that fungicide applications before and after grafting prevented soil-borne pathogen infections and improved sapling quality.

Alzheimer's disease (AD) remains a significant challenge in the field of neurodegenerative disor-ders, even nearly a century after its discovery, due to the elusive nature of its causes. The develop-ment of drugs that target multiple aspects of the disease has emerged as a promising strategy to address the complexities of AD and related conditions. The immune system's role, particularly in AD, has gained considerable interest, with nanobodies representing a new frontier in biomedical research. Advances in targeting antibodies against amyloid-β (Aβ) and using messenger RNA for genetic translation have revolutionized the production of antibodies and drug development, open-ing new possibilities for treatment. Despite these advancements, conventional treatments for AD, such as Cognex, Exelon, Razadyne, and Aricept, often have limited long-term effectiveness, under-scoring the need for innovative solutions. This necessity has led to the incorporating of advanced technologies like artificial intelligence and machine learning into the drug discovery process for neurodegenerative diseases. These technologies help identify therapeutic targets and optimize lead compounds, offering a more effective approach to addressing the challenges of AD and similar conditions.

Tomato is considered the most important vegetable crop worldwide. Improving the nutritional value of fruits must be based on sustainable production in terms of varieties and fertilization management. This study aimed to improve the nutritional value (total soluble solids, acidity, lycopene, β-carotene, polyphenols, macro and microelements) of two tomato varieties (‘Cristal’ and ‘Siriana’) under three fertilization types (NPK chemical fertilizer, chicken manure and biological fertilizer with microorganisms) for the greenhouse. Primary metabolism compounds do not vary significantly according to the type of fertilizer used. The results for the antioxidant compounds showed a better effect of biological fertilization compared to chemical fertilizer and control unfertilized. The tomato fruits from the local cultivar (‘Siriana’) are richer in nutritional compounds such as rutin, regardless of the type of fertilization, which denotes a good ability to adapt to crop conditions. Tomato cultivars reacted positively to microbiological fertilization compare to chemical, thus producing nutritious fruits under sustainable management. Tomato fruits were richer in the quality of microelement contents.

No system nor standardized analytical procedures at commercial laboratories exist to facilitate and accurately measure potential viable virus contamination in feed ingredients and complete feeds globally. As a result, there is high uncertainty of the extent of swine virus contamination in global feed supply chains. Many knowledge gaps need to be addressed to improve our ability to prevent virus contamination and transmission in swine feed. This review summarizes the current state of knowledge involving: 1) the need for biosecurity protocols to identify production, processing, storage, and transportation conditions that may cause virus contamination of feed ingredients and complete feed, 2) challenges of measuring virus inactivation, 3) virus survival in feed ingredients during transportation and storage, 4) minimum infectious doses, 5) differences between using a Food Safety Objective versus a Performance Objective as potential approaches for risk assessment in swine feed, 6) swine virus inactivation from thermal and irradiation processes, and chemical mitigants in feed ingredients and complete feed, 7) efficacy of virus decontamination strategies in feed mills, 9) benefits of functional ingredients, nutrients, and commercial feed additives in pig diets during a viral health challenge, and 10) considerations for improved risk assessment models of virus contamination in feed supply chains.

Chemical warfare agents (CWAs) are one of the most toxic compounds. Degradation of CWAs using decontamination agents is one of the few ways to protect human health against the harmful effects of CWAs. A ferrate Fe(VI) based potential chemical warfare agent decontaminant was studied for degradation of persistent nitrogen mustard (tris(2-chloroethyl)amine, HN3). By optimizing the reaction conditions, the complete degradation of HN3 was achieved in 4 minutes. The degradation products contained mostly reduced Fe species which confirmed the environmental friendliness of the proposed decontamination solution.

Homochirality is an obvious feature of life on Earth. On the other hand, extraterrestrial samples contain largely racemic compounds. The same is true for any common organic synthesis. Therefore, it has been a perplexing puzzle for decades how these racemates could have formed enantiomerically enriched fractions as a basis for the origin of homochiral life forms. Numerous hypotheses have been put forward as to how preferentially homochiral molecules could have formed and accumulated on Earth. In this article, it is shown that homochirality of the abiotic organic pool at the time of formation of the first self-replicating molecules is not necessary and not even probable. It is proposed to abandon the notion of a molecular ensemble and to focus on the level of individual molecules. Although the formation of the first self-replicating, most likely homochiral molecule is a seemingly improbable event, on a closer look, it is almost inevitable that homochiral molecules have formed simply on a statistical basis. In this case, the non-selective leap to homochirality would be one of the first steps in chemical evolution directly out of a racemic “ocean”. Moreover, most studies focus on the chirality of the primordial monomers with respect to an asymmetric carbon atom. However, any polymer with a minimal size that allows folding to a secondary structure, would spontaneously lead to asymmetric higher structures (conformations). Most of the functions of these polymers would be influenced by this inherently asymmetric folding. To summarize, simple and universal mechanisms may have led to homochiral self-replicating systems in the context of chemical evolution. A homochiral monomer pool is deemed unnecessary and probably never existed on primordial Earth.

Cynomorium songaricum is an important endangered plant with significant medicinal and edible values. However, the lack of resources and quality variation have limited the comprehensive developments and sustainable utilization of C. songaricum. Here, we evaluated chemical and genetic traits of C. songaricum from the highly suitable habitat regions simulated with species distribution models. The PCA and NJ tree analyses displayed intraspecific variation in C. songaricum, that could be divided into two ecotypes: ecotype I and ecotype II. Furthermore, the LC-MS/MS-based metabolomic was used to identify and analyze the metabolites of two ecotypes. The results indicated that a total of 589 compounds were detected, 236 of which were significantly different between the two ecotypes. Specifically, the relative content and the kind of flavonoids were more abundant in ecotype I, which were closely associated with the medicinal activities. In contrast, amino acids and organic acids were more enriched in ecotype II, which may provide better nutritional quality and unique flavor. In summary, our findings demonstrate the ecotype division and chemical diversity of C. songaricum in China from different geographical regions and provide a reference for the development of germplasm and directed plant breeding of endangered medicinal plants.

Condition monitoring is a primary principle for predictive maintenance. In this regard, several techniques have been employed, each of which has its strengths and weaknesses. In this work, the relationships between the electrical (ε', ε", tan δ) and chemical (Fe, Pb, Cu, Cr, Al, Si, Zn) properties of engine lubricants were investigated using soft computing models. The models' performance was evaluated considering some criteria, including RMSE and MAPE. The RBF model was determined as the best one to predict chemical properties (Fe, Pb, Cu, Cr, Al, Si, Zn) through electrical indexes (ε', ε", tan δ). The RBF’s parameters (e.g., hidden size and training algorithm) were then optimized for optimum performance. For instance, in the RBF model implemented to predict Al, the best hidden size and training algorithmic were 15 and 'trainlm', respectively. Finally, by sensitivity analysis it was observed that eliminating any of the inputs does not improve the performance of the RBF model performance. In general, the results of the current research showed that the electrical properties (e.g., ε', ε", tan δ) have the capability of estimating the contaminants in the lubricants which can improve the existing monitoring methods.

Vertical graphene nanowalls (VGNWs) have emerged as a highly promising material in recent years due to their exceptional properties, such as a high specific surface area, excellent electrical conductivity, scalability, and compatibility with transition metal compounds. These attributes make VGNWs a compelling candidate for various applications, including energy storage, catalysis, and sensing, fostering great interest in their use in next future commercial graphene-based sensors like optoelectronic and plasmonic devices, energy storage electrodes, and catalytic systems. Among the diverse graphene synthesis methods, plasma-enhanced chemical vapor deposition (PECVD) has proven to be a robust technique for producing large-scale graphene films and creating VGNWs on diverse substrates. However, despite substantial progress in optimizing growth conditions to achieve micrometer-sized graphene nanowalls, the outcomes are often obtained through empirical approaches, and a comprehensive understanding of the underlying physicochemical mechanisms governing nanostructure formation remains elusive. In particular, a deeper exploration of atomic-level phenomena, such as nucleation, carbon precursor adsorption, and surface diffusion of adatoms, is imperative to exert precise control over the growth process. Concerning the synthesis of VGNWs, hydrogen plays a dual role in the graphene growth process, acting as both a co-catalyst and an etchant for the nanowalls. Nevertheless, a thorough comprehension of the intricate growth process is still required. To address these knowledge gaps, this review paper aims to investigate the nucleation and growth of VGNWs using PECVD, with a specific focus on exploring the temperature effect on the graphene growth ratio and nucleation density across a wide range of temperatures. By providing valuable insights into the PECVD process, our objective is to enable the optimization of growth conditions for tailoring VGNWs' properties, thereby facilitating their application in energy storage, catalysis, and sensing fields.

Effective therapeutics for Alzheimer's disease (AD) are in great demand worldwide. In our previous work, we responded to this need by synthesizing novel drug candidates consisting of 4-amino-2,3-polymethylenequinolines conjugated with butylated hydroxytoluene via fixed-length alkylimine or alkylamine linkers (spacers) and studying their bioactivities pertaining to AD treatment. Here, we report significant extensions of these studies, including the use of variable-length spacers and more detailed biological characterizations. Conjugates were potent inhibitors of acetylcholinesterase (AChE, minimum IC50 15.1±0.2 nM) and butyrylcholinesterase (BChE, minimum IC50 5.96±0.58 nM), with weak inhibition of off-target carboxylesterase. Conjugates with alkylamine spacers were more effective cholinesterase inhibitors than alkylimine analogs. Optimal inhibition for AChE was exhibited by cyclohexaquinoline and for BChE by cycloheptaquinoline. Increasing spacer length elevated potency against both cholinesterases. Structure-activity relationships agreed with docking results. Mixed-type reversible AChE inhibition, dual docking to catalytic and peripheral anionic sites, and propidium iodide displacement suggested the potential of hybrids to block AChE-induced β-amyloid (Aβ) aggregation. Hybrids also exhibited inhibition of Aβ self-aggregation in the thioflavin test; those with a hexaquinoline ring and C8 spacer were the most active. Conjugates demonstrated high antioxidant activity in ABTS and FRAP assays as well as inhibition of luminol chemiluminescence and lipid peroxidation in mouse brain homogenates. Quantum-chemical calculations explained antioxidant results. Computed ADMET profiles indicated favorable blood-brain barrier permeability suggesting CNS activity potential. Thus, the conjugates could be considered promising multifunctional agents for potential treatment of AD.

This work investigated the effect of temperature and acid or alkalis chemical activation by pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) on the yield of bio-oil, hydrocarbon content of bio-oil, and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, KOH and HCl activation, in laboratory scale. The acidity of bio-oils and aqueous phases determined by AOCS methods, while the chemical composition of bio-oils and aqueous phase by GC-MS and FT-IR. The bio-char characterized by XRD. For the activation with KOH, the XRD analysis identified the presence of Kalicinite (KHCO3), the dominant crystalline phase in bio-char, while an amorphous phase was identified in bio-chars for the activation with HCl. The yield of bio-oil, for the pyrolysis of Açaí seeds activated with KOH, varied between 3.19 and 6.79 (wt.%), showing a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while the acidity of aqueous phase lies between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the pyrolysis experiments activated with HCl, the yield of bio-oil varied between 2.13 and 3.37 (wt.%), decreasing linearly with temperature, while that of gas phase varied between 17.91 and 37.94 (wt.%), increasing linearly with temperature. The acidity of bio-oil varied between 127.1 and 218.5 mgKOH/g, increasing with temperature, showing that higher temperatures did not favor the yield of bio-oil and bio-oils acidity. For the chemical activation with KOH, the FT-IR analysis of bio-oils identified the presence of chemical groups characteristics of hydrocarbons and oxygenates, while that of aqueous phase only groups characteristics of oxygenates. For the chemical activation with HCl, the FT-IR analysis of bio-oil and aqueous phases identified only the presence of groups characteristics of oxygenates. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with HCl activation, the GC-MS of bio-oil identified only the presence of oxygenates. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons while activation with HCl produced bio-oils with only oxygen compounds.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, antioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 at-mosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The antioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in bio-char, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil in-crease exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and de-creases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

The contexts where there is mining and agriculture activities are potential sources of risk to human health due to contamination by chemical mixtures. This study explored the association between the frequency of micronuclei and pesticides in regions with ferronickel (Montelibano, Córdoba) and gold (Nechí, Antioquia) mining, and a closed native mercury mine (Aranzazu, Caldas). A cross-sectional study was carried out with 247 residents in the mining regions. Sociodemographic, occupational, and toxicological variables were ascertained. Blood and urine samples were taken for pesticide analysis (12 organochlorines, organophosphates, and carbamates), 68 chemical elements were quantified in hair, and micronuclei (MN) were quantified in lymphocytes. The mixtures of chemical elements were grouped through exploratory factor analysis. Prevalence ratios (PR) were estimated with robust variance Poisson regressions to explore associations. The highest concentrations of chemical elements were in the active mines. The potentially most toxic chemical mixture was observed in the ferronickel mine. Pesticides were detected in a low proportion of participants. The frequency of MN was similar in the three mining contexts. There was great heterogeneity in the exposure to pesticides and chemical elements. The “hormetic effect” of selenium is described, in which at low doses it acts as a chelator and at high doses it can enhance the toxic effects of other elements. It is proposed that future studies in mining contexts include the measurement of chemical mixtures to better assess exposure and potential adverse health effects.

Target pests of genetically engineered crops producing both defensive allelochemicals and Bacillus thuringiensis (Bt) toxins often sequentially or simultaneously uptake allelochemicals, Bt toxins, and/or insecticides. How the three types of toxins interact to kill pests remains underexplored. Here we investigated the interactions of Bt toxin Vip3A, plant allelochemical flavone, and insecticide emamectin benzoate in Spodoptera frugiperda. Simultaneous administration of flavone LC25 + Vip3A LC25, emamectin benzoate LC25 + Vip3A LC25, and flavone LC15 + emamectin benzoate LC15 + Vip3A LC15 but not flavone LC25 + emamectin LC25 yielded a mortality significantly higher than their expected additive mortality (EAM). One-day preexposure to one toxin at LC5 followed by 6-day exposure to the same toxin at LC5 plus another toxin at LC50 showed that the mortality of flavone LC5 + Vip3A LC50, emamectin benzoate LC5 + Vip3A LC50, and Vip3A LC5 + emamectin benzoate LC50, were significantly higher than their EAM, while that of flavone LC5 + emamectin benzoate LC50 was significantly lower than their EAM. No significant difference existed among the mortalities of Vip3A LC5 + flavone LC50, emamectin benzoate LC5 + flavone LC50, and their EAMs. The results suggest that the interactions of the three toxins are largely synergistic (inductive) or additive, depending on their combinations and doses.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

Coffee processing generates a huge amount of waste which contains many natural products. Here, we report the discovery of a panel novel cell-penetrating and metal-ion binding microproteins designated coffeetide cC1a-c and cL1-6 from the husk of two popular coffee plants, Coffea canephora and Coffea liberica, respectively. Combining sequence determination and database search, we showed that the prototypic coffeetide cC1a is a 37-residue, eight-cysteine microprotein with a hevein-like cysteine motif but without a chitin-binding domain. NMR determination of cC1a revealed a compact structure that confers it resistance to heat and proteolytic degradation. Disulfide mapping together with chemical synthesis revealed that cC1a has a ginsentide-like, and not a hevein-like, disulfide connectivity. In addition, transcriptomic analysis showed that the 98-residue micrcoproten-like coffeetide precursor contains a three-domain arrangement like ginsentide precursors. Molecular modeling together with experimental validation revealed a Mg2+ and Fe3+ binding pocket at the N-terminus formed by three glutamic acids. Importantly, cC1a is amphipathic with a continuous stretch of 19 apolar amino acids, and which enables its cell penetration to target intracellular proteins, despite being highly negatively charged. Our findings suggest that coffee by-products could provide a source of ginsentide-like bioactive peptides that have potential to target intracellular proteins.

Egg white lysozyme was modified by chemical methods using organic acids. Caffeic acid and p-coumaric acid in organic acids were used as modifiers, and 1-Ethyl-3- (3-dimethylaminopropyl) carbodiimide hydrochloride and N-hydroxy succinimide were used as dehydration condensation agents during modification. A certain degree of modified lysozyme was obtained through appropriate modification conditions. The antibacterial properties and structure of the obtained two organic acid modified lysozymes were compared with natural enzymes. The results showed that compared with the natural enzyme, the activity of modified lysozyme decreased, but the inhibitory effect on Gram-negative bacteria was enhanced. The minimum inhibitory concentrations of caffeic acid modified enzyme and p-coumaric acid modified enzyme on Escherichia coli and Pseudomonas aeruginosa were 0.5 mg/mL and 0.75 mg/mL, respectively. However, the antibacterial ability of modified lysozyme to Gram-positive bacteria was lower than that of natural enzyme. The minimum inhibitory concentration of caffeic acid modified enzyme and p-coumaric acid modified enzyme to Staphylococcus aureus and Bacillus subtilis was 1.25 mg/mL. The peak fitting results of the amide-I band (1600 cm-1-1700 cm-1) absorption peak in the infrared spectroscopy showed that the content of the secondary structure of the two modified enzymes obtained after modification was different from that of natural enzymes.

In this study, the effects of food waste (FW) compost, vermicompost, and chemical fertilizers on the growth of organic red radish and soil quality are investigated to promote sustainable agriculture. Utilizing a comparative approach, it assesses the impacts of these fertilizers on various plant growth metrics and soil characteristics, highlighting the potential of converting FW into nutrient-rich amendments as a sustainable alternative to chemical fertilizers. The results indicate a significant variation in fresh weight among different treatments. For example, the FV 25% treatment demonstrated a relatively high mean fresh weight of 7.9664, while the CO 50% treatment yielded a much lower mean fresh weight of 0.2589. These numbers underscore the potential efficacy of specific FW treatments in enhancing plant growth, with VC 50% and FV 25% showing considerable promise in increasing crop yield. The study concludes that FW compost and vermicompost significantly enhance plant growth and soil quality, advocating for their use as sustainable and environmentally friendly alternatives to chemical fertilizers. The findings emphasize the importance of selecting appropriate fertilizer types and concentrations to optimize agricultural productivity and environmental sustainability, supporting the incorporation of FW into agricultural systems as a beneficial resource.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

Protein-protein interactions (PPIs) are associated with various diseases; hence, they are important targets in drug discovery. However, the physicochemical empirical properties of PPI-targeted drugs are distinct from those of conventional small molecule oral pharmaceuticals, which adhere to the ”rule of five (RO5).” Therefore, developing PPI-targeted drugs using conventional methods, such as molecular generation models, is difficult. In this study, we propose a molecule generation model based on deep reinforcement learning, specialized for generating PPI inhibitors. By introducing a scoring function that can represent the properties of PPI inhibitors, we successfully generated potential PPI inhibitor compounds. The generated virtual compounds possess the desired properties for PPI inhibitors, and show similarity to commercially available PPI libraries. These generated virtual compounds are freely available as a virtual library.

SARS-CoV-2 Omicron variant spike RBD epitopes in complex with spike (S) -protein D614G mutations now predominate globally and increase infectivity by assembling more functional S proteins into the virion. On average, homeopathic medicine contains less than one molecule per dose on average. Single variable SphericalHarmonicY, LaguerreL, WhittakerM, SphericalBesselJ, LegendreP, LegendreQ, LaguerreL, ChebyshevT, and Hypergeometric1F1 Functions pFqarise in connection with the power series solution of the Schrodinger equation or in the summation of perturbation expansions in quantum mechanics. A quantum interpretation of the homeopathic method is presented here through a novel algebraic topology approach to supersymmetry and symmetry breaking in quantum fields and quantum gravity theory with the aim of developing a wide range of physical-based drug design applications in a Small Molecule Quantized Water Memory Network suggesting that the Hidden Black Hole Paradox of Information Loss might be solved under suitable conditions.

In this work, an analytical and numerical analysis of the transition to chaos in five nonlinear systems of ordinary and partial differential equations, which are models of the autocatalytic chemical processes and the numbers of interacting populations, is carried out. It is analytically and numerically shown that in all considered systems of equations, further complication of the dynamics of solutions and the transition to chemical and biological turbulence is carried out in full accordance with the universal Feigenbaum-Sharkovsky-Magnitskii bifurcation theory through subharmonic and homoclinic cascades of bifurcations of stable limit cycles. In this case, irregular (chaotic) attractors in all cases are exclusively singular attractors in the sense of the FShM theory.

Recent development for synthesis of bio-based long chain aliphatic polyesters by acyclic diene metathesis (ADMET) polymerization of α,ω-dienes, derived from plant oils and bio-based chemicals, like bis(10-undecenoate) with isosorbide, using ruthenium-carbene catalysts have been reviewed. Development of subsequent (one-pot) tandem hydrogenation afforded saturated polyesters under mild conditions. The polymerizations under bulk (without solvent, 80-90 ºC) or in ionic liquids (50 ºC) under vacuum conditions enabled synthesis of high molar mass polymers (Mn >30,000 g/mol). The polymerization by molybdenum-alkylidene catalyst afforded the highest molecular weight polyesters (44000‒49400 g/mol, in toluene at 25 ºC) exhibiting promising tensile properties (strength and elongation at break) beyond polyethylene, polypropylene. Depolymerizations of these polyesters including closed loop chemical recycling were also demonstrated. Catalyst developments (more active, under mild conditions) play a key role for the efficient synthesis.

Abstract: The chemical mechanical polishing (CMP) has been widely used for surface modification of critical materials and components and provided global planarization of topography with a low post-planarization slope high quality and efficiency. The colloidal silica slurries play an important role in the finishing processes of optical components. Monodisperse mesoporous silica nanospheres were synthesized with different surfactant by Stöber method. Their architectural features and texture parameters were characterized by XRD, FTIR, N2 adsorption–desorption isotherms, SEM, XPS, and TGA techniques. The spherical SiO2 products presented with the controllable 50-150 nm particle size and distribution. The AFM micrographs reveal that flat and smooth surfaces without distinct scratches residual particles are achieved by using the as-obtained composite particles as abrasives[The particle size of SiO2 slurry plays a critical role in the chemical-mechanical polishing process.

The implications related to the fight against alien organisms often affect different sectors, from the economic to the landscape one or from the public health to the ecological one. This paper is an upgrade of our previous study focused on the evolution of the red palm weevil in a coastal urban area (central Italy); we investigate the evolution of this parasite in the following period (2013-2020), considering both the effectiveness of the chemicals used and their potential effects. With a multidisciplinary approach, on the one hand we carried out a spatio-temporal analysis to analyze the extent and mode of pest spread over time using historical aerial photos, freely available remote sensing images and field surveys, integrated in a GIS environment, and on the other hand we performed an assessment of the chemical risk associated with the substances used to protect the palms from the red weevil. The fight against weevil is now concentrated in specific areas (parks, relevant roads, villas, hotels, farmhouses, nurseries); the applied preventive chemical treatments are very effective in preserving the palms, but they show a toxic potential for all organisms. We discuss current local management of this pest focusing on the several aspects involve into the fight against this beetle in an urban area.

Honey bees (Apis mellifera L.) express complex behavioral patterns (aggressiveness) to exhibit defensive mechanisms for their survival. Their phenotypic expression of aggressive behavior is influenced by internal and external stimuli. Knowledge of this behavior is recently important though beekeepers are still faced with the challenges of selecting aggressive and less-aggressive bred lines. Field evaluation of aggressiveness among bred lines of honey bees is required to overcome the challenges. Chemical cues (alarm pheromone and isopentyl acetate mixed with paraffin oil), physical and visual stimuli (dark leather suede, colony marbling and suede jiggling) were used to evaluate aggressiveness and orientation among five bred lines of honeybee colonies. Our results showed that both chemical assays recruited bees but the time of recruitment was significantly lower for alarm pheromone. Honeybees’ response to both assays culminated to stings which differed among bred lines for alarm pheromone and paraffin when colonies were marbled. Honeybee aggression varied among bred lines and was higher in more aggressive bred lines compared to less-aggressive bred lines. Our findings suggest that it is crucial to repeatedly evaluate orientation aggressiveness at the colony level and among bred lines when selecting breeding colonies.

Фундук является одним из самых ценных орехов в мире благодаря своим уникальным органолептическим свойствам и питательным характеристикам. Данная работа была направлена ​​на анализ некоторых физико-химических свойств различных сортов фундука, выращиваемых в Закаталы (Азербайджан), а именно Ата-баба, Эльбари, Топкара, Фирован, Насими, Галиб, Мирзебейли, Тала, Даш финтик, Барли, Азери и Сачагли. В целом результаты показали статистически значимые различия между изучаемыми сортами. Плотность ядер в зависимости от сортов фундука варьировала от 0,71 г/см ³ (азери) до 1,03 г/см ^{3 .}(Сачакли). Очищенные плоды Дашфиндыг в среднем были тяжелее (1,64±0,34 г), а очищенные плоды Насими, Калиб, Мирзебейли и Сачакли в среднем легче (0,8±0,23 г, 0,8±0,31 г, 0,8±0,20 г и 0,80 г). ±0,09 г соответственно.В неочищенном виде самыми тяжелыми были орехи Дашфиндык (3,70±0,34 г), а самыми легкими из всех сортов были орехи Насими и Калиб (2,0±0,48 г и 2,0±0,36 г соответственно). - орехи баба составляют 49 масс./ядро, %, у остальных изученных сортов - 33,3-45,3 мас.%. Орехи насими имеют округлую форму (в экваториальной зоне); талы, ата-баба, фирован и азери - округло-продолговатые; топкара , Барли и Даш финдык – продолговатые; Эльбари, Калиб, Мирзебейли и Сачакли – удлиненные. Фирован, Тала и Топкара имеют более толстую скорлупу. Ата-баба значительно опережает другие сорта по выходу ядер (490 кг/1 т орехов) , На втором месте по этому показателю находится Тала (453 кг/1 тонна орехов), на третьем – Топкара (433 кг/1 тонна орехов). По максимальной жирности выделены сорта Мирзебейли (77,00±2,20 г/100 г ядер) и Фирован (75,0±3,08 г/100 ядер), по белку - Сачакли (16,02±0,50 г/100 ядер) и Ата-баба ( выделено 15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора.

This study addresses the challenge of assessing the carcinogenic potential of hazardous chemical mixtures, such as PFAS, which are known to contribute significantly to cancer development. Here, we propose a novel framework called HNNMixCancer that utilizes a Hybrid Neural Network (HNN) integrated into a machine-learning framework. This framework incorporates a mathematical model to simulate chemical mixtures and enables the creation of classification models for binary and multiclass classification and regression. Through extensive experimentation, we demonstrate that our HNN model outperforms other methodologies, including Random Forest, Bootstrap Aggregating, Adaptive Boosting, Support Vector Regressor, Gradient Boosting, Kernel Ridge, Decision Tree with AdaBoost, and KNeighbors, achieving a superior accuracy of 92.7% in binary classification. To address the limited availability of experimental data and enrich the training data, we generate an assumption-based virtual library of chemical mixtures using a known carcinogenic and non-carcinogenic single chemical for all the classification models. Remarkably, in this case, all methods achieve accuracies exceeding 98% for binary classification. In external validation tests, our HNN method achieves the highest accuracy of 80.5%. Furthermore, in multiclass classification, the HNN demonstrates an overall accuracy of 96.3%, outperforming RF, Bagging, and AdaBoost, which achieved 91.4%, 91.7%, and 80.2%, respectively. In regression models, HNN, RF, SVR, GB, KR, DT with AdaBoost, and KN achieve average R2 values of 0.96, 0.90, 0.77, 0.94, 0.96, 0.96, and 0.97, respectively, showcasing their effectiveness in predicting the concentration at which a chemical mixture becomes carcinogenic. Our method exhibits exceptional predictive power in prioritizing carcinogenic chemical mixtures, even when relying on assumption-based mixtures. This capability is particularly valuable for toxicology studies that lack experimental data on the carcinogenicity and toxicity of chemical mixtures. To our knowledge, this study introduces the first method for predicting the carcinogenic potential of chemical mixtures. The HNNMixCancer framework offers a novel alternative for dose-dependent carcinogen prediction. Ongoing efforts involve implementing the HNN method to predict mixture toxicity and expanding the application of HNNMixCancer to include multi-mixtures.

This study explores the impact of temperature and molarity in the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 atmosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physico-chemical property of fundamental importance in bio-fuels, of bio-oils and aqueous phases by AOCS methods. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in biochar, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil increase exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

Although the beneficial health effects of prebiotics have been demonstrated in numerous research papers, its incorporation into daily food remains unfamiliar to consumers. This work evaluates the resistant maltodextrin (RMD) addition in the sensory attributes of pasteurized orange juice, together with the physico-chemical properties and the aromatic profile. RMD addition moderately improved almost all sensory attributes evaluated by panellists. It also proportionally increased °Brix together with density and decreased acidity. Colour changes were registered with higher RMD concentrations. Orange pulp presence affected the volume particle size distribution analysis while RMD addition did not exercised any effect. The aroma volatile compounds were also analysed. Pulp-added samples marked higher alcohol and aldehydes quantity, whereas pulp-free samples registered higher terpenes and terpenoids values. Ketones and acids were also quantified. RMD had a moderate impact on volatile compounds quantifications, playing the orange pulp presence a much more decisive role. A correlation analysis was also performed to relate instrumental and sensorial determinations for all samples. This work proves that the addition of RMD to orange juice is technologically feasible while also achieving a good response at the sensory level.

This paper presents the concept of a novel adaptable sensing solution currently being developed under the EU Commission founded PHOTONGATE project. This concept will allow to quantify multiple analytes of the same or different nature (chemicals, metals, bacteria, etc.) in a single test with levels of sensitivity and selectivity at/or over those offered by current solutions. PHOTONGATE relies on two core technologies: a bio-chemical technology (molecular gates) which will confer the specificity and, therefore, the capability to be adaptable to the analyte of interest, and which combined with porous substrates will increase the sensitivity, and a photonic technology based on Local Surface Plasmonic Resonance (LSPR) structures serves as transducer for light interaction. Both technologies are in the micron range, facilitating the integration of multiple sensors within a small area (mm²). The concept will be developed for its application in health diagnosis and food safety sectors. It is thought as an easy-to-use modular concept, which will consist of the sensing module, mainly of a microfluidics cartridge that will house the photonic sensor, and a platform for fluidic handling, optical interrogation, and signal processing. The platform will include a new optical concept, fully Europe Union Made, avoiding optical fibers and expensive optical components.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

Background: Poisoning is a growing public problem that has shown increased prevalence in many countries worldwide, contributing to increased costs and mortalities. A lack of or insufficient information regarding the circumstances, chemicals, drugs and people at risk due to imperfect reporting system is regarded as a barrier to successful poisoning prevention and intervention efforts. In Saudi Arabia, poisoning cases are monitored at the central level in the Ministry of Health, with meticulous follow-up of cases across country areas through public health departments. The current study's objective was to describe the poisoning notification and reporting system in Makkah.Subjects and methods: All reports of chemical and drug overdose poisoning delivered to the environmental health and occupational safety department in Makkah Almukarramah over two years (2018-2019) were reviewed, together with verification of all systems, rules and guidelines organizing the performance of the department.Results: The total number of cases reported in 2018 was 209 cases, while it reached 42 cases in 2019. The overwhelming majority of the cases were Saudi (91.6%), with a slight predominance of males (57.4%) over females (42.6%). Generally, almost two-thirds of the cases occurred in children below 13 years (61.4%), most of the poisoning cases resulted from drug overdose (63.3%), while 34.7% were chemical poisoning. The most common drug poisoning was attributed to analgesics followed by antiepileptics, antihypertensive drugs, antipsychotics and antimicrobials, while cleaning and detergent agents were the most commonly poisoned chemicals. The majority of these agents were taken by the oral route. Children's chemical poisoning was significantly higher than that in older age groups (p<0.05). All intentional poisoning occurred in adults; the great majority of them (88.9%) used drug overdosing rather than chemical substances.Conclusion and recommendations: The current study results are consistent with most of the previous studies carried out in different regions in Saudi Arabia. Reviewing the performance and adherence of the “Environmental Health and Occupational Safety Department” to the guidelines and instruction regulating monitoring, notification and reporting of poison cases are satisfactory and the poisoning surveillance system is effective. Further in-depth studies are needed to elaborate other socioeconomic and demographic factors associated with chemical and drug overdose poisoning. Public health plans, policies and legislations should be implemented to reduce these factors, including prohibition over-the-counter pharmaceutical sales, selling the possibly harmful substances in kid-proof bottles and additional stringent rules governing chemical sale and storage. Intensive supervision of children is needed. Suicidal poisoning patients should seek psychiatric help to limit the possibility of attempting suicide again in the future. Furthermore, efforts are needed to plan and implement health education programs and campaigns about the factors proven in the current study to be significantly related to chemical and drug overdose poisoning to raise public knowledge about exposure to chemicals and its consequences. Popular communication media, commercial malls, road ads, learning institutions and workplaces can be used to deliver health education campaigns and programs. Advice on how to store chemicals safely and how to keep kids safe should be focused on during such programs.

Equines play an important role throughout the world, whether for work, culture, or leisure, providing an ever-growing significant contribution on the economy. The increase in importation and movement of horses, both nationally and internationally, has inevitably allowed for the global equine industry to grow. Subsequently however, the potential for transmission of fatal equine bacterial diseases has also escalated, and devasting outbreaks continue to occur. To prevent such events, disease surveillance and diagnosis must be heightened throughout the industry. Current common, or "gold-standard" techniques, have shown to be inadequate at times, thus requiring newer technology to impede outbreaks. Loop-mediated isothermal amplification (LAMP) has proven to be a reliable, rapid, and accessible tool in both diagnostics and surveillance. This review will discuss equine bacterial diseases of biosecurity relevance and their current diagnostic approaches, as well as their respective LAMP assay developments. Additionally, we will provide insight regarding newer technology and advancements associated with this technique, and their potential use for the outlined diseases.

Porous ferroelectric lead zirconate-titanate (PZT) films are a promising material for various electronics applications. This study focuses on understanding how structure-directing agent (polyvinylpyrrolidone) can change structure and electrical properties of porous PZT films prepared by chemical solution deposition. The films with various porosity up to ~ 40 vol.% and pore connectivity changing from 3-0 to 3-3 were prepared and studied by capacitance-voltage, dielectric hysteresis, transient current, photocurrent, and local current techniques. We have found that the linear decrease in the material volume in a porous film is not the only factor governing film properties. The key role in changing electrical properties plays the creation of new internal grain boundaries. This research expands the understanding of physical phenomena in porous ferroelectric films and may enable the development of new materials and devices.

This review delves into the significance of chemical communication in mammals, with an emphasis on the role of the vomeronasal system in sensing pheromone-mediated interactions. The vomeronasal system shapes a variety of social and sexual behaviors, including reproduction, hierarchy formation, maternal bonding, and species recognition. Intriguingly, this system presents a vast degree of evolutionary variability, more so than variations observed in the olfactory system. This adaptive diversity underscores the challenges in studying the vomeronasal system, emphasizing the need for detailed research into its neuroanatomy and functional morphology. This review traverses an array of topics central to our understanding of chemical communication in mammals. We begin with the foundational role and basic concepts of chemocommunication. This is followed by an in-depth exploration of the olfactory systems. Subsequently, the neuroanatomical underpinnings of the vomeronasal system are juxtaposed against those of the olfactory system. Our focus then shifts to an exhaustive study of the sensory element of the vomeronasal system, the vomeronasal organ, and the integrating center of this information, the accessory olfactory bulb. The discussion extends to secondary projections of both the olfactory and vomeronasal systems in the light of the dual olfactory hypothesis. The review culminates with a detailed look at four specific models of vomeronasal system organization belonging to four evolutionarily distinct mammalian families: rodents, marsupials, herpestids, and bovids. These have been meticulously analyzed by the authors, aiming to spotlight the significant morphofunctional differences stemming from the adaptive changes imprinted on the system.

The traditional processing of Dendrobium officinale (DO) is manufactured through five necessary processing steps: fresh strips, drying at 85 °C, curling, molding, and drying at 35 °C (Fengdou), and the antioxidant activity of DO were increased after processing into Fengdou. To comprehensively analyses the changing functional components, a plant-wide target metabolomics were employed. In total, 739 differential ingredients were identified in five processing treatments, mainly highlighting differences in variation with phenolic acids, flavonoids, lipids, and amino acids and their derivatives, and glycosylation of aglycone result in the up-regulation in flavonoid glycosides levels. Temperature is a key step in DO processing production. In addition, the main enrichment of specific differential ingredients was found in five different metabolic pathways, including glucosinolate biosynthesis, linoleic acid metabolism, flavonoid biosynthesis, phenylpropanoid biosynthesis, ubiquinone and other terpene quinone biosynthesis. Correlation analysis clarified that total phenols and flavonoids showed a significant positive correlation with antioxidant capacity. This study provides new insights into the influence of processing processes on DO quality, which may lead to guidance for the high-quality production of DO.

Nerve agents have recently been used in battlefield operations, espionage wars and terrorist attacks. These compounds, like some pesticides, cause organophosphate poisoning. The rapid, non-contact detection of a sarin simulant has been demonstrated at the Diagnostics and Metrology Laboratory of the Italian National Agency for New Technologies, Energy and Sustainable Economic Development using laser photoacoustic spectroscopy, an infrared absorption technology. The first measurements, carried out with an experimental system based on a quantum cascade laser and developed for the assessment of food authenticity in the “fingerprint region”, show that a detection limit of 1 nanolitre is within the reach of the instrument when chemometric analysis is applied.

A tunable near-infrared surface plasmon resonance (SPR) biosensor based on gate-controlled graphene plasmons is investigated theoretically. The novel characteristics of chemical potential sensing make the proposed sensor promising in the application of ultra-sensitive and highly specific biosensing technology. The sensitivity of chemical potential sensing in wavelength interrogation mode can be calculated to be 1.5, 1.89, 2.29, 3.21, 3.73 and 4.68 nm/meV respectively at the central wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. The much smaller full width half maximum (FWHMs) comparing with that of 2D nanomaterial-enhanced metal SPR sensors indicates higher figure of merit. The sensitivity of chemical potential sensing in gate voltage interrogation mode also can be calculated to be 156.9822, 143.6147, 131.0779, 111.0351, 101.3415 and 90.6038 mV/meV respectively at the incident wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. It can be estimated theoretically that the limit of detection (LOD) in DNA sensing of the proposed sensor can reach femtomolar level and even attomolar level, comparable to and even lower than that of 2D nanomaterial-enhanced metal SPR sensors with AuNPs as a sensitivity enhancement strategy. The feasibility of preparation and operation of this new concept SPR biosensor is also analyzed and discussed.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, an-tioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 atmosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The an-tioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) charac-terized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in biochar, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydro-carbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil increase exponentially with molarity, while those of oxygenates de-crease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and decreases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

Although the effect of thermal modification (TM) on teak wood color is well documented, a few studies were carried out in closed system processes, as well as it remains unclear the effect of different processes on the same material. This work aimed to verify the effect of closed and open system processes of TM on the color of fast-growing teak wood. Thermally modified wood was evaluated in a closed system at 160 °C (CS160) and in an open system at 185 °C and 210 °C (OS185 and OS210). We measured the moisture content (initial and final) of wood, and the corrected mass loss (CML). The chemical analyses encompassed the contents of alpha-cellulose, hemicelluloses, lignin, and extractives (total, in acetone and dichloromethane). Wood color was measured before and after TM according to the CIEL*a*b* color space. It was possible to achieve the same color using different processes of thermal modification (CS160 and OS210). TM reduced wood lightness (L*), red-green chromaticity coordinate (a*), and yellow-blue chromaticity coordinate (b*). L* and a* had the bigger and lower variations, respectively. The color of thermally modified wood was significantly changed, even at the mildest condition tested (OS185, 0.33% CML).

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Objective: This study aimed to validate the use of liquid phenol-based chemical peeling therapy for cervico-vaginal intraepithelial neoplasia (CIN and VaIN), with the goal of circumventing obstetric complications associated with surgical treatment. Methods: A total of 483 eligible women diagnosed with CIN and/or VaIN participated in this study. Participants underwent phenol-based chemical peeling therapy every 4 weeks until disease clearance. Disease clearance was determined by negative Pap tests for four consecutive weeks. HPV genotyping was conducted at the onset of the study and after disease clearance in select cases. Results: Among the 476 participants (excluding those with cancer), the number of treatment sessions until CIN/VaIN clearance ranged from 2 to 49 (median = 7 sessions). Forty-five participants (9.4%) underwent surgical treatments. Seven participants (1.5%) experienced recurrence, presenting with CIN2/VaIN2 or worse lesions; of these, three underwent LEEP, while four repeated the chemical peeling therapy. No obstetrical complications were noted among the 98 pregnancies following this therapy. The findings suggest that phenol-based therapy is safe and effective for CIN, although it requires numerous and lengthy treatments. Factors associated with resistance to this therapy include immune suppression, high-grade lesions, multiple HPV type infection, and direct or passive smoking.

Abstract: Chemical burns are one of the most dangerous and aggressive types of burns as they can cause significant tissue damage, leading to pain, inflammation, necrosis, and scarring. We present a burn case report associated with the use of Acellular Dermal Matrix (MatriDerm® MedSkin Solution Dr. Suwelack AG, Billerbeck, Germany) for the reconstruction of a Hallux after the patient was mistakenly administered intramuscular Nitric Acid at another institution. The patient presented with a third degree burn that compromised the medial aspect of the hallux’s skin, the distal phalanx and nail bed. Early debridement was performed, and Negative Pressure Wound Therapy (NPWT VAC, 3M, US) was used to preserve and promote tissue viability. Eight days later, the patient was taken to the OR, and Acellular Dermal Matrix and split-thickness skin graft were used to reconstruct her right hallux’s defect. The patient achieved adequate clinical evolution and was discharged with complete reconstruction of the burned area. Acellular Dermal Matrix proved to be an important and viable option for reconstructive surgery after a chemical burn, and further studies are warranted to ensure its routine usage in this kind of lesions. Keywords: chemical burn, acellular matrix, hallux reconstruction, NPWT

The leaf essential oils from five Eucalyptus spp.: E. astringens, E. camaldulensis, E. lehmanii, E. leucoxylon and E. sideroxylon growing in the same plantation area and conditions (plants with the same age and subjected to the same agronomic practices) were analyzed and evaluated for their antimicrobial activity. The essential oil yields ranged from 0.14 to 0.96% (w/w), and their chromatographic profiles were resolved into 48 compounds; among them, 11 were common to all essential oils. Terpenoids (oxygenated mono, and sesquiterpenes) dominated (55.66-76.67%) the oil profiles. Although 1,8-cineole (21.97-50.93%) was found as the main oxygenated monoterpene in all examined essential oils, principal component analysis observed and confirmed an interspecific chemical variability. Additionally, a set of distinctive chemical markers that could serve as a reliable tool for discrimination of Eucalyptus species and for authentication and quality control purposes (for commercial samples) has been defined for each essential oil. The antimicrobial disc-diffusion assay results revealed that all essential oils were endowed with a strong antimicrobial activity, with those derived from E. camaldulensis, E. lehmanii and E. leucoxylon being the most active.

Man-made chemicals have played an important role in the development of our modern society. They have revolutionized such areas as healthcare and farming and they are essential in the manufacture of a wide range of consumer products. In studying the behavior of radionuclides and metals in the bottom sediment-water system, special attention is paid to identifying the forms of existence of pollutants in terms of substantiating their migration ability and, as a result, the po-tential for their subsequent spread, i.e. secondary pollution. On the example of bottom sediments of the Yenisei River, such radionuclides as K-40, Cs-137 are shown to be present mostly in the undecomposed residue. Eu-252 and Am-241 are associated with the organic component of bottom sediments, consisting of plant and animal remains, as well as soil washed away from the floodplain part of the river bed. The radionuclide Co-60, depending on the mineralogical composition of bottom sediments, can either be almost evenly distributed between the undecomposed residue and organic matter, or dominate in the undecomposed residue. Thus, it is shown that man-made ra-dionuclides can have a high tendency to migrate, both in the thickness of bottom sediments and between such phases as bottom sediments and water.

One of the key pathogenetic links of type 2 diabetes mellitus (T2DM) is the formation of insulin resistance (IR). Besides a wide selection of synthetic antidiabetic drugs, various plant-origin extracts are also available to support the treatment of T2DM. This study aimed to investigate and gain knowledge of the chemical composition and potential IR correction effect of American cranberry (Vaccinium macrocarpon Aiton) leaf extracts and formulate novel 3D-printed oral dosage forms for such extracts. The bioactivity and IR of L-arginine-loaded cranberry leaf extracts were studied in vivo in rats. The cranberry leaf extracts consisted of quinic, 3-caffeoylquinic (chlorogenic), p-coumaroylquinic acids, quercetin 3-O-galactoside, quercetin-3-O-glucoside, quercetin-3-xyloside, quercetin-3-O-arabino-pyranoside, quercetin-3-O-arabinofuranoside, quercetin 3-O-rhamnoside and quercetin-O-p-coumaroyl-hexoside-2 identified by HPLC. In-vivo studies with rats showed that the oral administration of the cranberry leaf extracts had a positive effect on insulin sensitivity coefficients under ITT test, and affected HOMA-IR levels and liver lipid content with experimental IR. A novel 3D-printed immediate-release dosage form was developed for the oral administration of cranberry leaf extracts using polyethylene oxide (PEO) as a carrier gel in a semi-solid extrusion (SSE) 3D printing. In conclusion, American cranberry leaf extracts loaded with L-arginine could find uses in preventing health issues associated with IR.

This study aims to evaluate the effect of different drying methodologies (room, microwave, convective, oven and freeze-drying) on the chemical composition, the microbiological quality of extracts and the biological activities namely clotting milk and antioxidant activities for both spontaneous and cultivated Onopordum nervosum ssp. platylepis. The results showed that the drying methodology has significantly affected the phenolic composition. Freeze dried flowers showed the best amounts of total phenols, flavonoids and condensed tannins followed by the microwave dried flowers. However, the latest presented the lowest protein content. Finally, the biological activities were significantly dependent on the used drying process. The effective concentration EC50 values let to classify the samples according to their decreasing power to inhibit DPPH free radicals: dryer<oven<room <microwave<freeze-drying. The drying process significantly affected the clotting milk activity, freeze dried flowers showed the highest activity. All the obtained results do not reveal a significant difference between cultivated and spontaneous plants.

The study within the current research is focused on theoretical assessment of sustainable aviation fuels (SAF) obtained by blending traditional jet fuels Jet A and different liquids (biodiesel and alcohols) from analytical point of view. Within this paper in-depth analysis ofthe physical-chemical properties of Jet A fuel blended with different biodiesels and alcohols has been performed. Also within the blends Aeroshell 500 oil has been added (5% vol.) for ensuring the lubrication of the turbo engine. The blends consists of: Jet Aaviation fuel + biodieselfrom: palm oil, pork fat, sunflower oil and alcohols: methanol, ethanol and butanol. All the 6 liquids have been blended with Jet A in the following percentages: 10, 20 and 30%. Flash point, kinematic viscosity, density, freezing point, elemental analysis and FTIR analysis have been performed for all the liquids: Aeroshell 500, jet A, jet A + 10, 20, 30% biodiesel from waste palm oil, pork fat and waste sunflower oil, jet A + 10, 20, 30% methanol, ethanol and butanol, biodiesels and alcohols. The obtained results shows the influence of each of the blend’s components on the physical-chemical properties of the blends. Based on the physical-chemical analysis of the blends, conclusions on the behavior of the blends during burning and the gaseous pollutants resulting from the burning process can be drawn.

The positive impact of nature on human health has been explored by researchers. Although studies have indicated that olfaction and odors have an impact on both memory and health, re-search on the odor perception in relation to perceived health is scarce. A recent study found that the naturenatural scent from stem cuttings and potted plants of a specific rose-scented geranium Pelargonium graveolens, ‘Dr. Westerlund,’Westerlund’ had positive effects on stress-related mental disorders. reduction. Essential oils from many Pelargonium species, in particular ‘Dr. Westerlund’, are known to have phytochemical properties and pharmacological activities. No study has, so far, explored and identified the chemical com-pounds and the sensory perception of these compounds in stem cuttings and the potted ´Dr. Westerlund´ plantplants. Such knowledge would be an important contribution forto an increased understanding of the effects of plants’ chemical odor properties on human well-being and link this to the expressed perceived scents. Resulting sensory profiles of P.This study aimed to identify the sensory profile and suggest responsible chemical compounds of Pelargonium graveolens ´Dr. Westerlund´ as a potted plant and as stem cuttings were reported, as well as´. The sensory and chemical analysis results revealed sensory profiles of Pelargonium graveolens ´Dr. Westerlund´s, and suggestions for the chemical compounds that are attributed to the sensory profiles. Further studies are recommended to investigate the odor experience of scented pelargonium species in relation to various levels ofcorrelation between volatile com-pounds and possible stress hormones. reduction in humans.

Stellatolides are natural compounds that have shown promising biological activities, including antitumor, antimicrobial, and anti-inflammatory properties, making them potential candidates for drug development. Chemical Reactivity Theory (CRT) is a branch of chemistry that explains and predicts the behavior of chemical reactions based on the electronic structure of molecules. Conceptual Density Functional Theory (CDFT) and Computational Peptidology (CP) are computational approaches used to study the behavior of atoms, molecules, and peptides. In this study, we present the results of our investigation of the chemical reactivity and ADMET properties of Stellatolides A-H using a novel computational approach called Conceptual DFT-based Computational Peptidology (CDFT-CP). Our study uses CDFT and CP to predict the reactivity and stability of molecules and to understand the behavior of peptides at the molecular level. We also predict the ADMET properties of the Stellatolides A-H to provide insight into their effectiveness, potential side effects, and optimal dosage and route of administration. This study sheds light on the potential of Stellatolides A-H as promising candidates for drug development and highlights the potential of CDFT-CP for the study of other natural compounds and peptides.

Chemical safety is related to public health, safety and environmental concerns, and the dangerous chemicals safety problem is becoming the one that people commonly pay attention to. Strengthening chemical safety supervision not only involves safe production, but also is an important link to maintain social safety. Most related studies focus on chemical safety under normal regulation, this paper addresses the perspective of ‘special rectification’ and ‘normal regulation’, and establishes an evolutionary game model between chemical enterprises and government supervision departments under different supervision modes. Based on the evolutionary game theory, this paper studies the evolution process of the two game players' strategy choices, and compares and analyzes the evolution, stability and equilibrium between the chemical safety and the behavior strategies of government regulatory departments. The model is effectively analyzed based on numerical simulation, and the results show that: Under the ‘special rectification’ mode, the strategic choice of chemical enterprises engaging in safety without investment depends on the difference between the benefits and costs of safety without investment; In the ‘normal regulation’ mode, the choice of its safety non-investment strategy depends on the difference between the cost of engaging in safety investment and the cost of safety non-investment; Increasing the government's punishment will encourage chemical enterprises to take safety investment behavior under the two supervision modes. Increasing the punishment has a significant impact on the safety investment behavior of chemical enterprises under the ‘normal regulation’ mode, but it has no significant impact on the behavior of chemical enterprises under the ‘special rectification’ mode. At the same time, increasing the punishment will inhibit the strict supervision behavior of the government. The research conclusion provides important decision support for government departments to effectively supervise the safety production of chemical enterprises.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

Graphene/silicon (Si) heterojunction photodetectors are widely studied in detecting of optical signals from near-infrared to visible light. However, performance of the graphene/Si photodetectors is limited by defects created in the growth process and surface recombination at the interface. Herein, a remote plasma-enhanced chemical vapor deposition is introduced to directly grow graphene nanowalls (GNWs) at a low power, which can effectively improve the growth rate and reduce defects. Moreover, hafnium oxide (HfO2) grown by atomic layer deposition has been employed as an interfacial layer for the GNWs/Si heterojunction photodetector. It is shown that the high-k dielectric layer of HfO₂ acts as an electron blocking and hole transport layer, which minimizes the recombination and reduces dark current. By optimizing the thickness of HfO₂, an extremely low dark current of 3.85×10^(-10) A with a responsivity of 0.19 AW^(-1), as well as a specific detectivity of 1.38×10^12 Jones at zero bias can be obtained for the fabricated GNWs/HfO₂/Si photodetector. This work demonstrates a universal strategy to fabricate high-performance graphene/Si photodetectors.

This work is devoted to consideration and analysis of the application of molecular dynamics simulation (MDS) methods to the study of nanosized polymer polyvinylidene fluoride (PVDF) thin ferroelectric films (two-dimensional ferroelectrics) and their composites with graphene layers: 1) to study and calculations of the polarization switching time depending on the electric field and PVDF film thickness; 2) to study and calculations of the polarization switching time depending changes of the PVDF on PVDF-TrFE film; 3) to study the polarization switching time in PVDF under influence of graphene layers. All calculations at each MDS step were carried out using quantum semi-empirical methods PM3. A comparison and analysis of the results of these calculations and the kinetics of polarization switching within the framework of the Landau-Ginzburg-Devonshire theory for homogeneous switching in ferroelectric polymer films is carried out. The study of the composite heterostructures of the “graphene-PVDF” type and calculations of their polarization switching times were presented too. It is shown that replacing PVDF with PVDF-TrFE significantly changes the polarization switching times in these thin polymer films, and that introducing various graphene layers into the PVDF layered structure leads to both an increase and a decrease in the polarization switching time. Here everything also depends on the position and displacement of the ferroelectric coercive field depending on the system damping parameters.

In this study, the pristine MgO, MgO/CNT and Ni-MgO/CNT nanocomposites were processed by the impregnation and chemical vapour deposition methods and analyzed for hydrogen evolution (HER) via electrochemical water splitting process. Furthermore, effect of nickel on the deposited carbon was systematically elaborated in this study. The highly conductive carbon nanotubes (CNTs) deposited on the metal surface of the Ni-MgO nanocomposite heterostructure provides the robust stability and superior electrocatalytic activity. The optimized Ni-MgO/CNT nanocomposite exhibited hierarchical helical-shaped carbon nanotubes adorned on the surface of the Ni-MgO flakes, forming a hybrid metal-carbon network structure. The HER catalytic reaction was carried out in 1M alkaline KOH electrolyte, and the optimized Ni-MgO/CNT nanocomposite achieves the low 117 mV overpotential value (ɳ) at the 10 mA cm-2 and needs low 116 mV/dec Tafel value denoted Volmer-Heyrovsky pathway. Also, high electrochemical active surface area (ECSA) value of Ni-MgO/CNT nanocomposite acquires 515 cm2, which is favorable for the generation of abundant electro-active species and the prepared electrocatalyst durability was also performed by chronoamperometry test for prolonged duration of 20 h at 10 mA cm-2 and exhibits the good stability with 72% retention. Hence, obtained results demonstrated that the optimized Ni-MgO/CNT nanocomposite is highly active and cost-effective electrocatalyst towards hydrogen energy production.

In the last decades, consumers are increasingly interested in organic products and they strongly demand for reliability of the traceability of the organic products they use to buy and eat. Different researches have been carried out over the years to investigate on new and reliable systems to test the authenticity of products obtained using organic cultivation methods. The monitoring of some chemical components, derived from primary and/or secondary metabolism, in horticultural organic and conventional products, has highlighted the diversity induced by the two production techniques while the difference in fertilization practices has been shown to impact on the isotopic distribution of some elements, with particular reference to nitrogen. An integrated system is proposed to validate, through the acquisition of isotopic data and other chemical and biochemical parameters, the authenticity of organic products. This approach is intended to be coupled to the application of chemometric multivariate analysis of isotopic data combined with other quality and nutraceutical parameters, giving the possibility to discriminate organic from conventional products, thanks to the different isotopic signature impressed by the different nitrogenous source combined with the qualitative pattern of the crops, significantly affected by the different treatments. The main perspectives of the presented integrated approach, based on the combined use of chemometric and analytical tools, are linked to the feasibility of applying a reliable system to authenticate productions obtained with organic fertilizers (organic agriculture) respect to those obtained with the use of synthetic fertilizers (conventional agriculture), protect and valorize virtuous farmers and support political stakeholders and decision makers to counteract food fraud.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Surface chemistry evaluation plays a crucial role in assessing the efficacy of chemical decontamination products for titanium implants. This study aimed to investigate the effectiveness of chemical decontamination solutions in cleaning a contaminated dental implant surface and to evaluate the potential of combining Pluronic gel with hydrogen peroxide (NuBone®Clean) by evaluating pellicle disruption and re-formation on implant surfaces. In addition, ensuring safety with in- vitro and human testing protocols. X-ray Photoelectron Spectroscopy (XPS) was utilized for surface analysis. All the tested gels had some effect on the surface cleanness except for PrefGel®. Among the tested chemical decontamination candidates, NuBone®Clean demonstrated effectiveness in providing a cleaner titanium surface. Furthermore, none of the tested chemical agents exhibited any cytotoxic effects, and the safety assessment showed no adverse events. The results of this study highlight the significance of conducting comprehensive evaluations, encompassing safety and efficacy, before introducing new chemical agents for dental treatments. The findings suggest that NuBone®Clean shows potential as a chemical decontamination solution for implant surfaces. However, further investigation through randomized clinical trials is necessary. By adhering to rigorous testing protocols, the development of safe and efficient chemical decontamination strategies can be advanced, benefiting patients and promoting progress in the field of implant dentistry.

SiOx films, frequently derived from amino silane precursors, have found several applications with high added value. Although frequently used, the deposition of coatings from Tris(dimethyl amino)silane (TDMAS) has been reported to demand considerable amounts of energy, mainly due to the difficulty of oxidizing such compound. As it is well known, Plasma-enhanced atomic layer deposition (PEALD) is able to improve the oxidation efficiency even under low process temperatures. Owing to that, PEALD can be considered as a very promising technique for the deposition of SiOx coatings. In this work, it has been investigated the deposition of silicon oxide films using TDMAS at 150°C. It has been evaluated the effect of the plasma oxidation time (6 to 18 s) and of the atmosphere composition (pure O2 or O2+Ar) on the chemical structure, elemental composition and chemical bonding state of the films. Increasing the plasma oxidation time in pure O2 resulted in larger proportion of retained C (Si-CH3) whereas N was preserved in the structure (Si-N). on the other hand, the formation of SiOx films from TDMAS is favored in shorter oxidation times in O2 + Ar plasmas.

The mushroom industry generates large amounts of stems, a co-product with valuable sensory and health characteristics. This work aimed to study the influence of particle size (L — &gt;0.510 mm; LI — 0.510-0.315 mm; SI—0.315-0.180 mm; S — &lt;0.180 mm) and species in the characterization and antioxidant activity of flours from stems of Agaricus bisporus (ABSF) and Pleurotus ostreatus (POSF). ABSF was rich in protein (14 g/100 g), calcium (428.23-700.77 mg/100 g), and sorbitol (22.57-26.60 g/100 g), while POSF in β-glucans (36.62-40.34 g/100 g) and linoleic acid (20.57-39.86 g/100 g of lipid). Both species were flush in amino acids with umami flavor. The highest hydration properties and oil holding capacity were exhibited in the S size of both species. ABSF showed elevated values for emulsifying activity than POSF. ABSF-S recorded the heightened antioxidant capacity in vitro, in consonance with the total phenolic compounds (0.91 mg/g). However, this antioxidant assays in POSF presented a positive correlation with β-glucans content. According to these results, there could be several food applications for these co-products, such as emulsifier stabilizer, sweetener or fortifier in the development of functional food.

The study investigated the chemical and functional characterization of propolis collected in southern Italy, in particular in Basilicata, a region rich in ecological and vegetative biodiversity. Sixteen samples of propolis, collected within a radius of 40 km from each other in the Basilicata region, showed significant differences between the chemical and functional parameters investigated: color index (L*, a*, b*; P<0.05), variation in chemical composition and antioxidant activities, by ABTS and FRAP assays. In general, Lucanian propolis had a low content of waxes (P<0.05) and a high content of resin (P<0.05) and balsams (P<0.05). The content of total phenolic compounds and flavonoids were highly variable, as was the biological capacity. In conclusion, Lucanian propolis showed a remarkable variability, highlighting a significant diversification according to the geographical position and the diversity of the flora surrounding the apiary of which the bees use as a source of resin. This study therefore contributes to the enhancement of the quality of propolis, laying the foundations for the production and marketing of propolis not only in the food industry, but also in the pharmaceutical and cosmetic industries.

Tributyltin (TBT) is an environmental contaminant present on all continents, including Antarctica, with a potent biocidal action. Its use began to be intensified during the 1970s, being effectively banned in 2003, but remaining in the environment to this day due to several factors that increase its half-life and misuse despite the bans. In addition to the endocrine disrupting effect of TBT, that may lead to imposex induction in some invertebrate species, there are several studies that demonstrated that TBT also has an immunotoxic effect. The immunotoxic effects that have been observed experimentally in vertebrates using in vitro and in vivo models involve different mechanisms, but mainly alterations in the expression and/or secretion of cytokines. In this review, we summarize and update the literature on the impacts of TBT on the immune system, as well as discuss what still needs to be done to fill the knowledge gaps regarding the impact of this endocrine disrupting-chemical on immune system homeostasis.

This study examines the impact of weeds on sweet corn, where weeds compete with the main agricultural crops for essential elements such as nutrients, water, sunlight, and space for growth. In general. the use of herbicides is meant to suppress weed growth. Organic matter is important for plant growth and affects herbicide persistence. The study was aimed to explore the interdependence between ametryn herbicide and organic matter content and its impacts on weed growth, herbicide persistence, and sweet corn yield. The experiment was initiated in 2022 at the Experimental Station of the Faculty of Agriculture, Padjadjaran University, Indonesia, using a Split Plot Design in a Randomized Complete Block Design (RCBD) with three replicates. The experiments consisted of three levels of organic matter, i.e. low, medium, and high and 6 levels of ametryn herbicide at 0.0 (control), 0.5, 1.0, 1.5, 2.0, 2.5 kg a.i./ha. The results indicated that the apparent interdependence between ametryn herbicide doses of 1.5, 2.0 and 2.5 kg a.i./ha and the three levels of the organic matter content totally suppressed the weed growth. However, the effects of interdependence between ametryn herbicide and organic matter content on the herbicide persistence and on the sweet corn yield were not obvious. The ametryn herbicide gave excellent effects on sweet corn yield. Bioassay analysis showed that the lowest persistence of ametryn herbicide was in line with the highest content of the organic matter.

Lead optimization in drug discovery is a crucial phase where initial hits are refined into compounds with improved pharmacological properties. While traditional methods rely on manual experimentation and modifications, AI-driven techniques have revolutionized this process by leveraging big data and predictive modeling. This review explores how AI-driven approaches accelerate lead optimization, showcasing examples like deep neural networks and reinforcement learning. Integration of multi-omic data and experimental validation further enhances AI-driven strategies. The future lies in refining these AI methods, democratizing tools, and interdisciplinary collaboration to streamline drug discovery and address medical needs efficiently.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

The aim of the study was to verify whether a reduced nitrogen (N) fertilization rate according to the EU recommendation (“From field to table” directive) may guarantee good yields and will be sufficient to maintain soil fertility in monoculture maize cultivation in the no-tillage (NT) system versus the traditional plowing (P) system. Two fields (10 ha each) were established for P and NT maize cultivation where the following N doses were applied: 0.0; 69.0, 92.0, and 115.0 kg ha-1. Soils (0-20 cm) were sampled two times per year - in spring (before maize sowing) and in autumn (after maize harvesting). A broad range of chemical (reaction, water holding capacity, total and easily degradable carbon, ammonium, nitrates, magnesium, calcium, potassium, sulfur) and biological (respiration, humic acids) parameters were monitored during the experiment. The vast majority of these factors had higher values in autumn than in spring. Although the role of reduced fertilization was not shown to be significant, the correlation analysis revealed some relationships between yield and nutrient availability. The 20% reduction in N fertilization does not have an adverse effect on the chemistry and biological characteristics of soils and does not worsen their chemical and biological quality.

An increase in Spodoptera species was reported in Bt soybean fields expressing Cry1Ac insecticidal proteins in Brazil, requiring additional management with chemical insecticides. Here, we evaluated the dose effects of flubendiamide and thiodicarb on Spodoptera cosmioides (Walker, 1858), Spodoptera eridania (Stoll, 1782), Spodoptera albula (Walker, 1857) and Spodoptera frugiperda (J. E. Smith, 1797) (Lepidoptera: Noctuidae) that survived on MON 87751 × MON 87708 × MON 87701 × MON 89788, expressing Cry1A.105, Cry2Ab2 and Cry1Ac; MON 87701 × MON 89788 soybean, expressing Cry1Ac; and non-Bt soybean. On unsprayed Cry1A.105/Cry2Ab2/Cry1Ac soybean, only S. frugiperda showed ~60% mortality after 10 d, whereas S. cosmioides, S. eridania and S. albula showed >81% mortality. Surviving larvae of all species on this Bt soybean showed &gt;80% mortality when exposed to the field label dose of flubendiamide (70 mL/ha) or thiodicarb (400 g/ha) or at 50% of these doses. In contrast, all four species had <25% and <19% mortality on Cry1Ac and non-Bt soybean, respectively. Surviving S. cosmioides, S. eridania and S. albula on these soybean types presented >83% mortality post-exposure to both dose levels of flubendiamide and thiodicarb. Some S. frugiperda larvae surviving on Cry1Ac and non-Bt soybean sprayed with a 50% dose of either insecticide developed into adults. However, L1 larvae developing on Cry1Ac soybean leaves sprayed with flubendiamide and L2 larvae on this soybean sprayed with thiodicarb had a prolonged immature stage, and females lower fecundity, which are likely to impact its population growth on soybean.

Proteins in biological systems function at the interface of single molecule and bulk chemistry and thus provide novel insights into the basic physical chemistry of scaling and emergent phenomena. For example, a binary mechanical model based on the chemistry of muscle contraction unifies molecular mechanics and thermodynamics and provides an explicit solution to the Gibbs paradox. Using the same model system, here I show that chemical activities of molecular states have no effect on chemical kinetics or energetics. Specifically, while the concentration or number of molecules in a molecular state is widely thought to contribute to reaction free energies, here I show that it is not the physical presence of molecules that pushes a reaction forward but the number of microstates, , accessible in a chemical state that pulls a reaction toward equilibrium with an entropic force down an entropic funnel. With the derivation of an entropic contribution to chemical kinetics, I develop a novel chemical kinetic formulation that fully describes the chemical thermodynamics of both equilibrium and non-equilibrium reactions in terms of an a priori system reaction energy landscape.

The main aspects of mercury sulfide and mercury selenide thin film synthesis using the chemical deposition method are considered. An analysis of various factors affecting film properties was conducted, including the study of how the nature of the substrate and its pre-treatment influence film properties. The effects of the working solution's temperature, deposition time, and annealing conditions on film characteristics were investigated. The impact of these parameters on the phase composition, as well as optical, electrical, and morphological properties of the films, is discussed and summarized. The paragraph also explains how the choice and concentration of initial reagents affect the parameters, characteristics, and properties of the obtained films.

Environment pollution is one of the major problem that faces by our civilization . Textile industry is one of the factor for pollute the environment. In this study various causes that occurs by textile industry and pollute the environment will be shown and described. In textile industry for energy to run the factory various kind of fuel are used and in the industry there are many chemicals and dyes are used for the textile products. Plastic is one of the main substance for making the synthetic fabric. They pollute the air, water, soil and also they pollute the ecosystem of the various animals and destroy the ozone surface of the earth. For various kind of pollution that causes by textile industry the life of normal life hampered. They got ill and many time men and women lost their organs and sometimes they got attacked by various life taking illness.

Due to the low content, few studies are focused on the essential oils (EOs) of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (syn. Lamiophlomis rotata (Benth.) Kudô. This plant has been used to treat rheumatic arthritis and grasserie in China. However, such EOs may have important pharmacological activities such as anti-cancer. To identify the chemical markers (CM) in the EOs and evaluate their antioxidant activities (AAs), we firstly conduct a thoroughly investigation on their chemicals and AAs, to the best of our knowledge. Light yellow EOs with fresh and elegant smell are obtained by hydro-distillation with average yield 0.11% (volume mL/weight g). The crystals are separated from the EOs through cryoprecipitation, respectively. A total of 81 components are qualified and quantified in the EOs, crystals and EOs removed crystals, in which 44 ones are first reported. As for content, the main compounds are long-chain fatty acids (FAs) and their esters. The most abundant one n-hexadecanoic acid (palmitic acid, PA) accounting for 43.15-54.8%, 58.49-64.57% and 15.9-41.1%, in the EOs, crystals and EOs removed crystals, respectively. Seven compounds including PA, tetradecanoic acid, linoleic acid, oleic acid, methyl hexadecanoate, hexahydrofarnesyl acetone and phytol can be chosen a the CMs in these EOs. The AAs are evaluated through in vitro assays. PA presents pro-oxidant activities in a concentration dependence manner. Usually, the EOs removed crystals demonstrate stronger AAs, and the crystals demonstrate weaker AAs compared with that of the corresponding EOs, which is related to the different content of PA in these samples. This study can give some hints for the utilization of such EOs which are abundant in FAs such as PA.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

Abstract: Agriculture uses plastic products for containers, packaging, tunnels, drip irrigation tub-ing, mulches. Large amounts of plastics are used as mulches on the soil surface for vegetable pro-duction (tomato, cucumber, watermelon, strawberry, vine) to reduce the weed competition, in-crease water and fertilizer use efficiency and enhance crop yield. Portugal uses around 4,500 t/year of polyethylene plastic to cover approximately 23,000 ha of agricultural land and only a small amount is recovered for recycling or secondary uses because of dirt with soil, vegetation, pesticide and fertilizers. Cleaning and decontaminating polyethylene mulch are costly and commercial technology is often not accessible nor economically viable in the current economic Portuguese situation. Most plastic mulch is composed of polyethylene that degrades slowly and produces a large quantity of residues in soil with negative impact in the environment. In the present study, the effects of long-term cultivation of blueberry using green 100% high density polyethylene mulch, in the south Portugal were evaluated for soil chemical and biological changes. High density green plastic mulch did not contaminate the topsoil with di(2-ethylhexyl) phthalate and heavy metals, buttotal nitrogen and organic carbon concentrations, electric conductivity and microbial activity were reduced in the planting row compared with bare soil, without mulching. Further-more, the presence of plastic mulch did not affect negatively the presence of nematodes, and the Rhabditida (bacterial feeders) increased in the planting and covered row.

A simple method is presented for the continuous generation of carbon nanotube forests stably anchored on stainless-steel surfaces using a reactive-roll-to-roll (RR2R) configuration. No addition of catalyst nanoparticles is required for the CNT-forest generation, the stainless-steel substrate itself being tuned to generate the catalytic growth sites. The process enables very larges surfaces covered with CNT forests having individual CNT roots anchored to the metallic ground through primary bonds. Fog water harvesting is demonstrated and tested as one potential application using long CNT-covered wires. The RR2R is performed in the gas phase, no solution processing of CNT suspensions is used contrary to usual R2R CNT-based technologies. Full or partial CNT-forest coverage provides tuning of the ratio and shape of hydrophobic and hydrophilic zones on the surface. This enables optimization of fog water harvesters for droplet capture through the hydrophobic CNT forest, and water removal from the hydrophilic SS surface. Water recovery tests using small harp-type harvesters with CNT-forest generate water capture of up to 2.2 g/cm2h under ultrasound-generated fog flow. The strong CNT root anchoring on the stainless steel surfaces provides opportunities for (i) robustness and easy transport of the composite structure, (ii) chemical functionalization and/or nanoparticle decoration of the structures, and opens the road for a series of applications on large scale surfaces, including fog harvesting.

Thymus is an herbaceous perennials or subshrubs of the Lamiaceae family and is widely distributed worldwide. Essential oils extracted from thymus have attracted much attention owing to their potential biological functions. Here, we evaluated the chemical compositions of eight thyme essential oils (TEOs) using gas chromatography-mass spectrometry and assessed their antioxidant activity and in potential role in antibacterial and tumor therapy. The results showed that (1) the main components in eight TEOs were monoterpene hydrocarbons and oxygenated monoterpenes, and the chemical compositions of TEOs were affected by the specie factor; (2) eight TEOs could be divided into 3 groups (thymol-, geraniol-and nerol acetate-type), and thymol was main type; (3) eight TEOs had some common compounds, such as thymol and p-cymene, which were the main components in seven TEOs; (4) eight TEOs had antioxidant activit, and thymol-type EOs had strong antioxidant activity, while geraniol-type EOs had relatively weak antioxidant activity. In addition, it was found thymol had strong antibacterial activity against the growth of Escherichia coli and Staphylococcus aureus, and antimigratory activity of A549 cell. Overall, our results can provide theoretical basis for further exploring the function of natural products from thyme essential oils.

The review explores the therapeutic potential of mangrove plants as sources of bioactive compounds, particularly focusing on their anti-inflammatory properties. Mangroves, found in tropical and sub-tropical tidal coasts, exhibit unique ecological and biological activities. The review compiles and examines 136 research findings published between 1982 and 2018, with 41 studies specifically addressing the anti-inflammatory properties of mangroves in Indian coastal regions, including the Andaman and Nicobar Islands. It summarizes the chemical structures, molecular weights, formulas, solvents, and biological activities of these mangroves, as reported by various researchers over time. The data underscore the significant potential of tropical Indian mangroves in anti-inflammatory applications. However, a notable research gap exists regarding the extraction of bioactive compounds from mangrove species in the Andaman and Nicobar Islands compared to other regions such as Gujarat, Maharashtra, Goa, Karnataka, Kerala, Tamil Nadu, Andhra Pradesh, Odisha, West Bengal, and Puducherry. Overall, the compilation provides valuable insights into mangrove-based studies for drug discovery research, emphasizing the need for further exploration and exploitation of these natural resources.

Molecular structures, in chloroform and DMSO solution, of the monounsaturated free fatty acids (FFAs) caproleic acid (dec-9-enoic acid) and oleic acid (octadec-9-enoic acid) and the ω-3 FFAs α-linolenic acid (9Z,12Z,15Z)-octadeca-9,12,15-trienoic acid ALA), eicosapentanoic acid (5Z,8Z,11Z,14Z,17Z)-icosa-5,8,11,14,17-pentaenoic acid) and docosahexaenoic acid (4Z,7Z,10Z,13Z,16Z,19Z)-docosa-4,7,10,13,16,19-hexaenoic acid), are reported with the combined use of NMR and DFT calculations. Variable temperature and concentration chemical shifts of the COOH protons and transient 1D NOE experiments, in CDCl3, demonstrate the major contribution of low molecular weight aggregates of dimerized fatty acids, through intermolecular hydrogen bond interactions of the carboxylic groups, with parallel and antiparallel interdigitated structures, even at the low concentration of 20 mM. For the dimeric DHA, a structural model of an intermolecular hydrogen bond through carboxylic groups and an intermolecular hydrogen bond between the carboxylic group of one molecule and the ω-3 double bond of a second molecule, is shown to play a role. In DMSO-d6 solution the centro-symmetric hydrogen bond interactions are broken and the carboxylic groups form strong intermolecular hydrogen bond interactions with a discrete solvation molecule of DMSO. These solvation species form parallel and antiparallel interdigitated structures of low molecular weight. DFT structural models in CHCl3 and DMSO, in agreement with the NMR data, are compared with the structures in the liquid state