Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

Anomaly detection is an active area of research with numerous methods and applications. This survey reviews the state-of-the-art of data-driven anomaly detection techniques and their application to the the aviation domain. After a brief introduction to the main traditional data-driven methods for anomaly detection, we review the recent advances in the area of neural networks, deep learning and temporal-logic based learning. We cover especially unsupervised techniques applicable to time series data because of their relevance to the aviation domain, where the lack of labeled data is the most usual case, and the nature of flight trajectories and sensor data is sequential, or temporal. The advantages and disadvantages of each method are presented in terms of computational efficiency and detection efficacy. The second part of the survey explores the application of anomaly detection techniques to aviation and their contributions to the improvement of the safety and performance of flight operations and aviation systems. As far as we know, some of the presented methods have not yet found an application in the aviation domain. We review applications ranging from the identification of significant operational events in air traffic operations to the prediction of potential aviation system failures for predictive maintenance.

Microplastics (of size < 5mm) pollution in our environment is of current concern by researchers, public media and non-governmental organizations. Implications by their presence in aquatic and soil ecosystems have been well studied and documented, but less attention has been paid on airborne microplastics (MPs). Studies concerning airborne microplastics started from 2016 and only a few (n=7) have been published till date. Although, studies may increase in the following years, since air is very important for human survival. Microplastics have been observed in atmospheric fallouts in indoor and outdoor environments using a sampling or vacuum pump, rain sampler and/or particulate fallout collector. Identification and quantification have been carried out by visual, spectroscopic and spectrometric techniques. Factors such as meterological, climatic and anthropogenic influence the distribution and movement of airborne MP. Human exposure may be through inhalation or dermal route with their potential biopersistence and translocation. Ingestion may cause localized inflammation and cancer due to responses by the immune cells, especially in individuals with compromised metabolism and poor clearance mechanisms. Ecological risks involve possible contamination of the ecosystem through a dynamic relationship of MPs in soil, water and air forming a MP contamination cycle. The present review aimed at providing a comprehensive overview of current knowledge or information regarding microplastics in air, identifies gap in knowledge and give suggestions for future research.

Salinity intrusion is one of the most serious consequences of climate change coupled with rising sea level that significantly affects agricultural activities in many parts of the world. This phenomenon has increasingly become more serious and frequently occurred in the Mekong Delta of Vietnam. As a result, Vietnam has been ranked among top five countries where have been devastatingly impacted by climate change, in particular, its Tra Vinh Province characterized by coastal plain and alluvial deposit. In addition, this area is of the tropical monsoon zone of long rainy season with source of salt brought from the sea by the tides and sea level rise. Regions that are contaminated by salt are located in lowland and often suffer from floods linking to tidal effects with salty water from river systems and channels. Soil salinity evaluation is critical for coastal protection, restoration, and agricultural planning since it can be considered as an agricultural indicator to evaluate quality of soil. Here, we attempt to estimate the soil salinity in Tra Vinh Province, in the Mekong Delta of Vietnam. Landsat 8 OLI images are utilized to derive indices for soil salinity evaluation including single bands, Vegetation Soil Salinity Index (VSSI), Soil Adjusted Vegetation Index (SAVI), Normalized Difference Vegetation Index (NDVI), and Normalized Difference Salinity Index (NDSI). Subsequently, satistical analysis between soil salinity, electrical conductivity (EC, dS/m), and environmental indices derived from Landsat 8 OLI image is performed. Results indicate that spectral value of Near Infrared (NIR) band and VSSI are highly correlated with EC (R2 = 0.7779 and R2 = 0.6957, respectively) in comparison with the other indices. Comparative results show that soil salinity derived from Landsat 8 is consistent with in situ data. Findings of this study demonstrate that Landsat 8 OLI images reveal a high potential for spatiotemporally monitoring the magnitude of soil salinity at the top soil layer. Outcomes of this study are useful for agricultural activities, planners, and farmers by providing the base map of soil salinity contamination for better selection of accomodating crop types to reduce economical lost in the context of climate change. Our proposed method that estimates soil salinity using satellite-derived variables can be applied in the other regions.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), known to cause 2019-coronavirus disease (COVID-19) pandemic is a zoonotic coronavirus and crosses species to infect human populations, where an efficient transmission of virus occurs human-to-human. Nationwide lockdown is being adopted to stop public transport, keep people at their homes and out of their work, and maintain social distancing. In turn, large geographic areas in the world (including China, Italy, Spain, and USA) has been almost halted. This temporary halt is significantly slashing down the air pollution (air pollutants and warming gases) in most cities across the world. This paper: (i) introduces both COVID-19 and air pollution; (ii) overviews the relation of air pollution with respiratory/lung diseases; (iii) compiles and highlights major data appeared in media and journals reporting lowering of air pollution in major cities those have been highly impacted by the COVID-19; and also (iv) lists the way forward in the present context. Because COVID-19 is an ongoing pandemic and currently far from over, strong conclusions could not be drawn with very limited data at present. The temporary slashed down global air pollution as a result of COVID-19 restrictions are expected to stimulate the researchers, policy makers and governments for the judicious use of resources; thereby minimise the global emissions, and maintain their economies once the pandemic eases. On the other, lifting of the nationwide lockdown and eventual normalisation of the temporarily halted sectors may also reverse the currently COVID-19 pandemic-led significantly slashed down global air pollution that could make the future respiratory health crisis grimmer.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

Current problem facing researchers globally is microplastics as well as toxic chemical pollution of the ecosystem. Microplastics carry toxic chemicals in the ecosystem.serving as a vector for transport. In this study, a review of the literature has been conducted with the following objectives: (1) to summarise the concentrations of toxic chemicals such heavy metals and hydrophobic organic contaminants sorped on microplastics; (2) to evaluate their spatial distribution regarding adsorbed contaminant (3) to discuss plausible mechanism by which microplastics adsorp or desorp toxic chemicals in the environment; (4) to discuss implications of their occurrence in air, water and soil media; and (5) to discuss the impact of ingested microplastics to human health. Microplastics are ubiquitous environmental contaminant. Concentrations of sorped toxic chemical varied with location which represents a local problem; industrialized areas (especially areas experiencing crude oil related activities or have history of crude oil pollution) have higher concentrations than less industrialized areas. Ingestion of microplastics has been demonstrated in a range of marine and soil organisms as well as edible plants, thus possible contaminating the base of the food-web. Potential health effect to human is by particle localization, chemical toxicity and microbal toxins. We conclude by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

Background: Covid-19 was first reported in Wuhan, China in Dec 2019. Since then, it has been transmitted rapidly in China and the rest of the world. While Covid-19 transmission rate has been declining in China, it is increasing exponentially in Europe and America. Although there are numerous studies examining Covid-19 infection, including an archived paper looking into the meteorological effect, the role of outdoor air pollution has yet to be explored rigorously. It has been shown that air pollution will weaken the immune system, and increase the rate of respiratory virus infection. We postulate that outdoor air pollution concentrations will have a negative effect on Covid-19 infections in China, whilst lockdowns, characterized by strong social distancing and home isolation measures, will help to moderate such negative effect. Methods: We will collect the number of daily confirmed Covid-19 cases in 31 provincial capital cities in China during the period of 1 Dec 2019 to 20 Mar 2020 (from a popular Chinese online platform which aggregates all cases reported by the Chinese national/provincial health authorities). We will also collect daily air pollution and meteorology data at the city-level (from the Chinese National Environmental Monitoring Center and the US National Climatic Data Center), daily inter-city migration flows and intra-city movements (from Baidu). City-level demographics including age distribution and gender, education, and median household income can be obtained from the statistical yearbooks. City-level co-morbidity indicators including rates of chronic disease and co-infection can be obtained from related research articles. A regression model is developed to model the relationship between the infection rate of Covid-19 (number of confirmed cases/population at the city level) and outdoor air pollution at the city level, after taking into account confounding factors such as meteorology, inter- and intra-city movements, demographics, and co-morbidity and co-infection rates. In particular, we shall study how air pollution affects infection rates across different cities, including Wuhan. Our model will also study air pollution would affect infection rates in Wuhan before and after the lockdown. Expected findings: We expect there be a correlation between Covid-19 infection rate and outdoor air pollution. We also expect that reduced intra-city movement after the lockdowns in Wuhan and the rest of China will play an important role in reducing the infection rate. Interpretation: Infection rate is growing exponentially in major cities worldwide. We expect Covid-19 infection rate is related to the air pollution concentration, and is strongly dependent on inter- and intra-city movements. To reduce the infection rate, the international community may deploy effective air pollution reduction plans and social distancing policies.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Efficient oxygen evolution reaction (OER) electrocatalysts are highly desired in the field of water electrolysis and rechargeable metal-air batteries. In this study, a chelate polymer, composed of copper (II) and dithiooxamide, was used to derive an efficient catalytic system for OER. Upon potential sweep in 1M KOH, copper (II) centers of the chelate polymer were transformed to CuO and Cu(OH)2. The carbon-dispersed CuO nanostructures formed a nanocomposite which exhibits an enhanced catalytic activity for OER in alkaline media. The nanocomposite catalyst has overpotential of 280 mV (at 1 mA/cm2) and a Tafel slope of 81 mV/dec in 1M KOH solution. It has a seven-fold higher current than IrO2/C electrode, per metal loading. A catalytic cycle is proposed, in which, CuO undergoes electrooxidation to Cu2O3 that further decomposes to CuO with releasing oxygen. This work reveals a new method to produce an active nanocomposite catalyst for OER in alkaline media using a non-noble metal chelate polymer and a porous carbon. This method can be applied to the synthesis of transition metal oxide nanoparticles used in the preparation of composite electrodes for water electrolyzers and can be used to derive cathode materials for aqueous-type metal-air batteries.

Research have been conducted in many countries around the world to assess air quality during COVID-19 pandemic, especially during lockdown period, some of these studies found an increase or decrease in some pollutants. This paper investigates the impact of COVID-19 on seven air pollutants (i.e., PM_2.5, PM₁₀, NO₂, O₃, SO₂, H₂S, CO) from the period January 2020 to December 2020 in the State of Kuwait. Kuwait is a desert country located in the north-eastern part of the Arabian Peninsula, and the northeast of the Arabian Gulf (Persian as it is sometimes called). Several analytical methods were conducted, such as spatial analysis (spatial interpolation) to study the distribution of the studied variables. The data was also statistically analysed (time series analysis - Kernel density) to study the temporal changes. The analysis also included applying air quality index to the data. We found that concentrations for the pollutants decreased during the pandemic due to the decrease of anthropogenic sources including such as traffic and petroleum activities, but the concentration for PM_2.5 increased, mostly because of the transported dust coming with the northwest winds prevailing in Kuwait from the Arabian deserts and Iraq.

The study of the concentrations and effects of fine particulate matter in urban areas have been of great interest to researchers in recent times. This is due to the acknowledgment of the far-reaching impacts of fine particulate matter on public health. Remote sensing data have been used to monitor the trend of concentrations of particulate matter by deriving aerosol optical depth (AOD) from satellite images. The Center for International Earth Science Information Network (CIESIN) has released the second version of its global PM_2.5 data with improvement in spatial resolution. This paper revisits the study of spatial and temporal variations in particulate matter in Saudi Arabia by exploring the cluster analysis of the new data. Cluster analysis of the PM_2.5 values of Saudi cities is performed by using Anselin local Moran’s I statistic. Also, the analysis is carried out at the regional level by using self-organizing map (SOM). The results show an increasing trend in the concentrations of particulate matter in Saudi Arabia, especially in some selected urban areas. The eastern and south-western parts of the Kingdom have significantly clustering high values. Some of the PM2.5 values have passed the threshold indicated by the World Health Organization (WHO) standard and targets posing health risks to Saudi urban population.

Traffic congestion is one of the foremost problems confronted by the urban and suburban tenants of today. Traffic congestion increases vehicle emissions and degrades air quality. Urban planners and policy makers have consequently been always investigating choices to alleviate traffic congestion and to enhance air quality. Teleworking is one option that has received significant consideration and has been studied in the recent past. The aim of the study is to explore the relationship between teleworking, air quality and traffic in Switzerland. The analysis relies on panel individual and household level data over the period 2002-2013. We examine five main air pollutants; the sulphur dioxide (SO₂), the ground-level ozone (O₃) the nitrogen dioxide (NO₂), the carbon monoxide (CO) and the particulate matter less than 10 microns (PM₁₀). Based on the fixed effects estimates, teleworking reduces traffic volume by 1.9 per cent. Furthermore, the reduction observed on air pollution is higher for NO₂, CO and PM₁₀ ranging between 3.3-3.7 per cent, followed by O₃ at 2.3 per cent and SO₂ at 2.1 per cent. According to instrumental variable (IV) approach and the two stage least squares (2SLS) method, the effect is higher ranging between 2.6-4.1 per cent. The respective reduction on traffic becomes 2.7 per cent. Overall, the main concluding remark of the study is that teleworking can be a promising tool for urban planning and development, focusing at the traffic volume reduction, and the air quality improvement. Additional policy implications of teleworking and its beneficial effects for the society are further discussed.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

The importance of predicting the exposure to environmental hazards is highlighted by issues like global climate change, public health problems caused by environment stresses, and property damages and depreciations. Several approaches have been used to assess potential exposure and achieve optimal results under various conditions, for example, for different scales, groups of people, or certain points in time. Micro-simulation tools are becoming increasingly important in human exposure assessment, where each person is simulated individually and continuously. This paper describes an agent-based model (ABM) framework that can dynamically simulate human exposure levels, along with their daily activities, in urban areas that are characterized by environmental stresses such as air pollution and heat stress. Within the framework, decision making processes can be included for each individual based on rule-based behavior to achieve goals under changing environmental conditions. The ideas described in this paper are implemented in a free and open source NetLogo platform. A simplified modeling scenario of the ABM framework in Hamburg, Germany, further demonstrates its utility in various urban environments and individual activity patterns, and portability to other models, programs and frameworks. The prototype model can potentially be extended to support environmental incidence management by exploring the daily routines of different groups of citizens and compare the effectiveness of different strategies. Further research is needed to fully develop an operational version of the model.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

This paper deals with the environmental characterization of a large and densely populated area, with a poor reputation for contamination, considering the contribution of environmental features (air, soil, soil hydraulic and groundwater) and the potential effects on human health. The use of Geographic Information System (GIS) has made possible a georeferenced inventory and, by overlaying environmental information, an operational synthesis of comprehensive environmental conditions. The cumulative effects on environmental features were evaluated, taking into account superposition effects, by means of the spatial multicriteria decision analysis (S-MCDA). The application of the S-MCDA for converging the combination of heterogeneous factors, related to soil, land and water, deeply studied by heterogeneous groups of experts, constitutes the novelty of the paper. The results confirmed an overall higher potential of exposure to contaminants in the environment and higher mortality rates in the study area for some tumours, but hospital admissions for tumours were generally similar to the regional trend. Besides, mortality data may be strictly dependent on the poor socioeconomic conditions, quality of therapy and a lack of welfare in the area relative to the rest of Italy. Finally, as regards the possible relationship between presence of contaminants in the environment and health conditions of the population no definite conclusions can be drawn, although the present study encourages the use of the new proposed methods, that increase the possibilities for studying the combined effect of more environmental factors.

The problem of real-time estimation of occupancy of buildings (number of people in various zones at every time instant) is relevant to a number of emerging applications that achieve high energy efficiency through feedback control. The measurement of CO2 concentration can be considered an important indicator that allows to define the occupation of closed and crowded spaces. Interesting cases can be school buildings and other buildings used in civil and residential (shopping centres, hospitals, etc.). This paper, starting from an experimental analysis in different classrooms of a University campus in real operating conditions, in different period of the year, proposes a possible correlation between CO2 concentration and the occupancy profile of the spaces. The acquired data are used to present some graphical correlations and to understand the most important variables or combination of them. Starting from an accurate analysis of the data, attempts are made to define a preliminary estimation method through the development of a mathematical models of occupancy dynamics in a building, which show interesting results.

This paper introduces a new destriping algorithm for remote sensing data. The method is based on combined Haar Stationary Wavelet transform and Fourier filtering. State-of-the-Art methods based on the discrete wavelet transform (DWT) may not always be effective and may cause different artifacts. Our contribution is three-fold: i) we propose to use the Undecimated Wavelet transform (UWT) to avoid as much as possible shortcomings of the classical DWT; ii) we combine a spectral filtering and UWT using the simplest possible wavelet, the Haar basis, for a computational efficiency; iii) we handle 2D fields with missing data, as commonly observed in ocean remote sensing data due to atmospheric conditions (e.g., cloud contamination). The performances of the proposed filter are tested and validated on the suppression of horizontal strip artifacts in cloudy L2 Sea Surface Temperature (SST) and ocean color snapshots.

Social distancing policies put in place during COVID-19 epidemic in addition to helping to limit the spread of the disease also contributed to improving urban air quality. Here we show a decrease in air pollutant concentration as a consequence of mobility reduction in São Paulo during the containment measure which began on 22^nd March 2020. When comparing to foregoing weeks to equivalent periods of 2019, the concentration of most air pollutants sharply decreased in the first days of mobility restriction, to then increase again after government officials downplayed the threat of the disease. This trend is also followed by a decrease in hospital admissions by SARS-influenza. Therefore, despite the great economic and social unrest caused by the pandemic, this unique situation shows that large-scale mobility reduction policy had a significant impact on air quality, benefiting, directly and indirectly, the public health system.

The provision requirement of 10% openings of the total floor area stated in the Uniform Building by Law 1984 Malaysia has been practiced by designers for building plan submission approval. However, the effectiveness of thermal performance in landed residential buildings, despite the imposition by the by-law, has never been empirically measured and proven. Although terraced houses in Malaysia have dominated 40.9% of the total property transaction in 2019, such mass production with typical designs hardly provides its occupants with thermal comfort due to the static outdoor air condition and lack of external windows, where the conventional ventilation technique does not work well, even for houses with an air well system. Consequently, the occupants need to rely on mechanical cooling, which is a high energy-consuming component contributing to outdoor heat dissipation and therefore urban heat island effect. Thus, encouraging more effective natural ventilation to eliminate excessive heat from the indoor environment is critical. Since most of the research focuses on simulation modelling lacking sufficient empirical validation, this paper drawing on field measurement investigates natural ventilation performance in terraced housing with an air well system. More importantly, the key concern as to what extent the current air well system serving as a ventilator is effective to provide better thermal performance in the single storey terraced house is to be addressed. By adopting an existing single storey air welled terrace house, the existing indoor environmental conditions and thermal performance were monitored and measured using scientific equipment, namely HOBO U12 air temperature and air humidity, the HOBO U12 anemometer and the Delta Ohm HD32.3 Wet Bulb Globe Temperature meter for a six-month duration. The findings show that the air temperature of the air well ranged from 27.48°C to 30.92°C, while the mean relative humidity were from 72.67% to 79.25%. The mean air temperature for a test room (single sided ventilation room) ranged from 28.04°C to 30.92°C with a relative humidity of 70.16% to 76%. These empirical findings are of importance, offering novel policy insights and suggestions to potentially revising the existing building code standard and by laws; since the minimum provision of 10% openings has been revealed to be less effective to provide a desired thermal performance and comfort, mandatory compliance with, and the necessity for, the bylaw requirement should be revisited and further studied.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

A numerical mechanism connecting ice algal ecodynamics with the buildup of organic macromolecules is tested within modeled pan-Arctic brine channels. The simulations take place offline in a reduced representation of sea ice geochemistry. Physical driver quantities derive from the global sea ice code CICE, including snow cover, thickness and internal temperature. The framework is averaged over ten boreal biogeographic zones. Computed nutrient-light-salt limited algal growth supports grazing, mortality and carbon flow. Vertical transport is diffusive but responds to pore structure. Simulated bottom layer chlorophyll maxima are reasonable, though delayed by about a month relative to observations due to uncertainties in snow variability. Upper level biota arise intermittently during flooding events. Macromolecular concentrations are tracked as proxy proteins, polysaccharides, lipids and refractory humics. The fresh biopolymers undergo succession and removal by bacteria. Baseline organics enter solely through cell disruption, so that the internal carbon content is initially biased low. By including exudation, agreement with dissolved organic or individual biopolymer data is achieved given strong release coupled to light intensity. Detrital carbon then reaches hundreds of micromolar, sufficient to support structural changes to the ice matrix.

The cruise ship industry has become a well-implemented industry in the Baltic Sea area, and each year, the number of cruise ship passengers rises steadily. Efficient waste management in cruising ports around the Baltic Sea is a crucial element in minimizing environmental impacts. This research involves the four selected ports of Copenhagen, Helsinki, Stockholm and Tallinn. The study applies statistics and interview data to the analysis of waste management systems for cruise ship-generated waste. The interview data involves 14 executives and professionals responsible for environmental issues and decision making in their respective ports. The interviews highlighted the need for standardized environmental legislation and related procedures, which would result in coherent measurement systems. These systems would enable transparent environmental monitoring, thus maintaining the ports’ competitiveness. A common environmental legislation would support the emerging waste management system for the whole Baltic Sea area. We suggest that ports should focus on handling specific types of wastes and collaborate as a spatial network. Specialization to allow discharge of certain fractions of waste is essential. The paper concludes by addressing demands for future research, particularly vessel- and customer behavior focused studies.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The worldwide spread of Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) has ubiquitously impacted many aspects of life. As vaccines continue to be manufactured and administered, limiting the spread of SARS-CoV-2 will rely more heavily on the early identification of contagious individuals occupying reopened and increasingly populated indoor environments. In this study, we investigated the utility of an impaction-based aerosol sampling system with multiple nucleic acid collection media. Heat-inactivated SARS-CoV-2 was utilized to perform bench-scale, short-range aerosol, and room-scale aerosol experiments. Through bench-scale experiments, AerosolSense Capture Media (ACM) and nylon flocked swabs were identified as the highest utility media. In room-scale aerosol experiments, consistent detection of aerosol SARS-CoV-2 was achieved at a concentration equal to or greater than 0.089 genome copies per liter of room air (gc/L) when air was sampled for eight hours or more at less than one air change per hour (ACH). Shorter sampling periods (~75 minutes) yielded consistent detection at ~31.8 gc/L of room air and intermittent detection down to ~0.318 gc/L at (1 and 6+ ACH respectively). These results support further exploration in real-world testing scenarios and suggest the utility of indoor aerosol surveillance as an effective risk mitigation strategy in occupied buildings.

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which is difficult to be found in naturally available materials. The acoustic metamaterials have demonstrated to exhibit excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials' recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field is discussed as well.

Solar green roofs, namely rooftops functionalized with properly selected living vegetation and photovoltaic modules, achieve an ideal symbiotic relationship in which promotion of biodiversity and onsite renewable energy production are both enhanced whereas the roof provides a wide range of environmental, health, aesthetic and economic benefits. This study provides a unified outlook of this eminent sustainable technology at the dawn of its uptake across the world, especially in polluted urban areas.

The sea level rise, a consequence of climate change, is one of the biggest challenges that countries and regions with coastal lowland areas will face in the medium term. This study proposes a methodology for assessing the vulnerability to sea level rise (SLR) on the Atlantic coast of Portugal mainland. Some scenarios of extreme sea level for different return periods and extreme flooding events were estimated for 2050 and 2100, as proposed by the European Union Directive 2007/60/EC. A set of physical parameters are considered for the multi-attribute analysis technique implemented by the Analytic Hierarchy Process, in order to define a Physical Vulnerability Index fundamental to assess coastal vulnerability. For each SLR scenario, coastal vulnerability maps, with spatial resolution of 20 m, are produced at national scale to identify areas most at risk of SLR, constituting key documents for triggering adaptation plans for such vulnerable regions. For 2050 and 2100, it is estimated 903 km² and 1146 km² of vulnerable area, respectively, being the district of Lisbon the most vulnerable district in both scenarios. Results are available through a Web Map Service, for Portuguese public entities, and through a web map viewer for public and communities in general.

In the summertime, convections occur frequently over the Tibetan Plateau (TP) because of the large dynamic and thermal effects of the landmass. Measurements of vertical air velocity in convective cloud are useful for advancing our understanding of the dynamic and microphysical mechanisms of clouds and can be used to improve the parameterization of current numerical models. This paper presents a technique for retrieving high-resolution vertical air velocity from convective cloud over the TP, by using Doppler spectra from a vertically pointing Ka-band cloud radar. The method is based on the development of a “small-particle-traced” idea and the necessary data processing and uses three modes of radar. Spectral broadening corrections, uncertainty estimations, and result merging are used to ensure accurate results. Qualitative analysis of two typical convective cases shows that the retrievals are reliable and agree with the expectant results inferred from other radar measurements. A quantitative retrieval of vertical air motion from a ground-based optical disdrometer is used to preliminarily validate our radar-derived results. The comparison illustrates that while the data trends from the two methods of retrieval are similar, with the updrafts and downdrafts coinciding, cloud radar has a much higher resolution and can reveal the small-scale variation of vertical air motion.

Maritime Continent (MC) positions in between Asian and Australian summer monsoons zone. Its complex topography and shallow seas around it is a major challenge for the climate researchers to model and understand it. Monsoon in this area is affected by inter-scale ocean-atmospheric interactions like El-Niño Southern Oscillation (ENSO), Indian Ocean Dipole (IOD) and Madden-Julian Oscillation. Monsoon rainfall in MC (especially in Indonesia and Malaysia) profoundly exhibits its variability dependency on ocean-atmospheric phenomena in this region. This monsoon shift often introduces to dreadful events like biomass burning (BB) in Southeast Asia (SEA) which sometimes leads to severe trans-boundary haze pollution. In this study, the episode of BB in 2015 of SEA is highlighted and discussed. Observational satellite datasets are tested by performing simulations with numerical weather prediction (NWP) model using WRF-ARW (Advanced research WRF). Observed and model datasets are compared to study the sea surface temperature (SST) and precipitation (rainfall) anomalies influenced by ENSO, IOD and MJO. Correlations have been recognised which explains the delayed rainfall of regular monsoon in MC due to the influence of ENSO, IOD and MJO during 2015 BB episode, eventually leading to intensification of fire and severe haze.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

This paper aims to investigate carbon monoxide (CO) concentrations on roadways of Karachi, potential blood levels carboxy-hemoglobin (COHb) in Karachi. Geographical information system (GIS) was used for spatial analysis of diseases potentiality while an interpolation technique has been applied for surface generation with town boundaries and later evaluates risk areas.The higher concentration of carbon monoxide in the ambient is mainly due to automobile emissions. The City center and CBD areas are more perilous.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

Arctic feedbacks will accelerate climate change and could jeopardise mitigation efforts. The permafrost carbon feedback releases carbon to the atmosphere from thawing permafrost and the sea ice albedo feedback increases solar absorption in the Arctic Ocean. A constant positive albedo feedback and zero permafrost feedback have been used in nearly all climate policy studies to date, while observations and models show that the permafrost feedback is significant and that both feedbacks are nonlinear. Using novel dynamic emulators in the integrated assessment model PAGE-ICE, we investigate nonlinear interactions of the two feedbacks with the climate and economy under a range of climate scenarios consistent with the Paris Agreement. The permafrost feedback interacts with the land and ocean carbon uptake processes, and the albedo feedback evolves through a sequence of nonlinear transitions associated with the loss of Arctic sea ice in different months of the year. The US’s withdrawal from the current national pledges could increase the total discounted economic impact of the two Arctic feedbacks until 2300 by $25 trillion, reaching nearly $120 trillion, while meeting the 1.5 °C and 2 °C targets will reduce the impact by an order of magnitude.

A radial basis function network (RBFN) method is proposed to reconstruct daily Sea surface temperatures (SSTs) with limited SST samples. For the purpose of evaluating the SSTs using this method, non-biased SST samples in the Pacific Ocean (10°N–30°N, 115°E–135°E) are selected when the tropical storm Hagibis arrived in June 2014, and these SST samples are obtained from the OISST products according to the distribution of AVHRR L2p SST and in-situ SST data. Furthermore, an improved nearest neighbor cluster (INNC) algorithm is designed to search the optimal hidden knots for RBFNs from both the SST samples and the background fields. Then the reconstructed SSTs from the RBFN method are compared with the results from the optimum interpolation (OI) method. The statistical results show that the RBFN method has a better performance of reconstructing SST than the OI method in the study, and the average RMSE is 0.48°C for the RBFN method, which is quite smaller than the value of 0.69°C for the OI method. Additionally, the RBFN methods with different basis functions and clustering algorithms are tested, and we discover that the INNC algorithm with multi-quadric function is quite suitable for the RBFN method to reconstruct SSTs when the SST samples are sparsely distributed.

This paper deals with a generic methodology to evaluate the magnetic parameters of contactless power transfer systems. Neumann's integral has been used to create a matrix method that can model the magnetics of single coils (circle, square, rectangle). The principle of superposition has been utilised to extend the theory to multi-coil geometries such as double circular, double rectangle and double rectangle quadrature assuming linearity of magnetics. Numerical and experimental validation has been performed to validate the analytical models developed. A rigorous application of the analysis has been carried out to study misalignment and hence the efficacy of various geometries to misalignment tolerance. Comparison of single-coil and multi-coil shapes considering coupling variation with misalignment, power transferred and maximum efficiency is carried out.

A novel indole, microindolinone A (1), was isolated from a deep-sea-derived actinomycete Microbacterium sp. MCCC 1A11207, together with 18 known compounds (2–19). By detailed analysis of the ¹H, ¹³C, HSQC, COSY, HMBC, HRESIMS, and CD data, the absolute configuration of 1 was elucidated as 5R-hydroxy-4,5,6,7-tetrahydroindole-4-one. Noteworthily, 1 is the second example of a saturated indole isolated from nature.

This study examined the use of high dosages of ultraviolet germicidal irradiation (UVGI) (253.7 nm) to deal with various concentrations of air pollutants, such as formaldehyde (HCHO), total volatile organic compounds (TVOC), under various conditions of humidity. We also estimated the emission of ozone as a secondary pollutant of UVGI as treatment. A number of irradiation methods were applied for various durations in field studies to examine the efficiency of removing HCHO, TVOC, bacteria, and fungi. The removal efficiency of air pollutants (HCHO and bacteria) through long-term exposure to UVGI appears to increase with time. The effects on TVOC and fungi concentration were insignificant in the first week; however, improvements were observed in the second week. No differences were observed among the various irradiation methods in this study regarding the removal of HCHO and TVOC; however significant differences were observed in the removal of bacteria and fungi.

The airborne inoculum of Fusarium circinatum, the fungal pathogen causing Pine Pitch Canker (PPC), is one of the main means of spread of the disease in forest stands and forest nurseries. Since this world-wide known pathogen was introduced in Europe, its biology in this newly infected area still remains scarcely known. To shed more light on this topic, we set an experiment on a naturally PPC infected forest of Monterey pine in Galicia (NW Spain) with the following two goals: (i) to describe the seasonal spore dispersal pattern during one year of regular sampling and (ii) to assess the spatial spore dispersal pattern around the infested plot. Portable rotating arm spore traps were used and complemented with meteorological measurements. The abundance of F. circinatum spores in the samples was evaluated by quantitative PCR (qPCR) with hydrolysis probe. The results showed almost permanent occurrence of the air inoculum throughout the whole year, being detected in 27 of the 30 samplings. No clear temporal trends were observed, but higher air inoculum was favoured by previous lower air temperatures and lower leaf wetness. Conversely, neither rainfall nor air humidity seemed to have any significant importance. The spatial spread of the inoculum was noted to be successful up to a distance of 1000 m in the wind direction, even with winds of just 5 m s^-1. Our study shows that rotating arm spore traps combined with qPCR may be an efficient tool for F. circinatum detection.

This paper presents a methodology for determining the sensitivity of the main air flow directions in ventilation subnetworks to changes of aerodynamic resistance and of air density in mine workings. Formulae for determination of the sensitivity of the main subnetwork air flows by establishing the degree of dependency of the air volume stream in a given working on the variations in resistance or air density of other workings of the network have been developed. They have been implemented in the VentGraph mine ventilation network simulator. This software, widely used in Polish collieries provides an extended possibility to predict the process of ventilation, air distribution and, in the case of underground fire, also the spread of combustion gasses. The new method facilitates assessment by mine ventilation services of the stability of ventilation systems in exploitation areas and determine of the sensitivity of the main subnetwork air flow directions to changes of aerodynamic resistance and air density. Recently in some Polish collieries new longwalls are developed in seams located deeper then the bottom of the intake shaft. Such solution is called “exploitation below the level of access” or “sublevel”. The new approach may be applied to such developments to assess the potential of changes of direction and air flow rates. In addition, interpretation of the developed sensitivity indicator is presented. While analyzing air distributions for sublevel exploitation, application of current numerical models for calculations of the distribution results in tangible benefits, such as the evaluation of the safety or risk levels for such exploitation. Application of the VentGraph computer program, and particularly the module POŻAR (fire) with the newly developed options, enables an additional approach to the sensitivity indicator in evaluating air flow safety levels for the risks present during exploitation below the level of the intake shaft. The analyses performed and examples presented enabled useful conclusions in mining practice to be drawn.

Local air quality is a major concern for the population regularly exposed to high levels of air pollution. The airport, mainly due to its aircraft engines activities during taxiing and take off, is often submitted to heterogeneous but important concentrations of NOx and PM. The study suggests an innovative approach to determine the air traffic impact on air quality at the scale of the airport, its runways and terminals, in order to be able to locate the persistent high concentrations spots. The pollutants concentrations at 10 m resolution and 1 s time step are calculated in order to identify the most affected areas of an airport platform. A real day of air traffic on a regional airport is simulated, using real data as aircraft trajectories (from radar streams). In order to estimate the aircraft emissions, the Air Transport Systems Evaluation Infrastructure (IESTA) is used. Regarding local air quality, IESTA relies on the non-hydrostatic meso-scale atmospheric model Meso-NH using grid-nesting capabilities with 3 domains, for this study. The detailed cartography of the airport distinguishes between grassland, parking and terminals, allowing to compute exchanges of heat, water and momentum between the different types of surfaces and the atmosphere as well as the interactions with the building using a drag force. The dynamic parameters like wind, temperature, turbulent kinetic energy and pollutants concentration are computed at 10 m resolution over the 2 × 4 km airport domain. The pollutants are considered in this preliminary study as passive tracers, without chemical reactions. This preliminary study aims at proving the feasibility of high scale modelling over an airport with state of the art physical models.

The North Sea Offshore Grid concept has been envisioned as a promising alternative to: 1) ease the integration of offshore wind and onshore energy systems, and 2) increase the cross-border capacity between the North Sea region countries at low cost. In this paper we explore the techno-economic benefits of the North Sea Offshore Grid using two case studies: a power-based offshore grid, where only investments in power assets are allowed (i.e. offshore wind, HVDC/HVAC interconnectors); and a power-and-hydrogen offshore grid, where investments in offshore hydrogen assets are also permitted (i.e. offshore electrolysers, new hydrogen pipelines and retrofitted natural gas pipelines). We compare these scenario results with a business as usual scenario, in which offshore wind is connected radially to the shore and no offshore grid is deployed. All scenarios are run with the IESA-NS model, without any specific technology ban and under open optimization. This paper also presents a novel methodology, combining Geographic Information Systems and Energy System Models, to cluster offshore spatial data and define meaningful offshore regions and offshore hub locations. This novel methodology is applied to the North Sea region to define nine offshore clusters taking into account offshore spatial claims, and identifying suitable areas for single-use and multi-use of space for renewable energy purposes. The scenario results show that the deployment of an offshore grid provides relevant cost savings, ranging from 1% to 4.1% of relative cost decrease (2.3 bn € to 8.7 bn €) in the power-based, and ranging from 2.8% to 7% of relative cost decrease (6 bn € to 14.9 bn €) in the power-and-hydrogen based. In the most extreme scenario (H2) an offshore grid permits to integrate 283 GW of HVDC connected offshore wind and 196 GW of HVDC meshed interconnectors. Even in the most conservative scenario (P1) the offshore grid integrates 59 GW of HVDC connected offshore wind capacity and 92 GW of HVDC meshed interconnectors. When allowed, the deployment of offshore electrolysis is considerable, ranging from 61 GW to 96 GW, with capacity factors of around 30%. Finally, we also find that, when imported hydrogen is available at 2 €/kg (including production and transport costs), large investments in an offshore grid are not optimal anymore. In contrast, at import costs over 4 €/kg imported hydrogen is not competitive.

Observation of the ambient aerosol surface area concentrations is important to understand the aerosol toxicity because an increased surface area may be able to act as an enhanced reaction interface for certain reactions between aerosol particles and biological cells, as well as an augmented carrier surface for co-pollutants. In this study, the concentration of aerosol surface area was measured from April 2015 to March 2016 in Fukuoka, Japan. We investigated the monthly and diurnal variations in the correlations between the aerosol surface area and black carbon (BC) and sulfate concentrations. Throughout the year, aerosol surface area concentration was strongly correlated with the concentrations of BC, which has relatively large surface area since BC particles are usually submicron agglomerates consisting of much smaller (tens of nanometers) sized primary soot particles. The slopes of the regression between the aerosol surface area and BC concentrations was highest in August and September 2015. This appears to have been the results of an increase in the proportion of the airmass that originated on the main islands of Japan. This may enhance the introduction of the BC from the main islands of Japan that is relatively fresh (or “uncoated”), thereby maintaining its larger surface area.

The data assimilation method to improve sea fog forecast over the Yellow Sea is usually three-dimensional variational assimilation (3DVAR), whereas ensemble Kalman filter (EnKF) has not yet been applied on this weather phenomenon. In this paper, two sea fog cases over the Yellow sea, one spread widely and the other spread narrowly along the coastal area, are studied in detail by a series of numerical experiments with 3DVAR and EnKF based on the Grid-point Statistical Interpolation (GSI) system and the Weather Research and Forecasting (WRF) model. The results show that the assimilation effect of EnKF outperforms that of 3DVAR: for the widespread-fog case, the probability of detection and equitable threat scores of the forecasted sea fog area get improved respectively by ~57.9% and ~55.5%; the sea fog of the other case completely mis-forecasted by 3DVAR is produced successfully by EnKF. These improvements of EnKF relative to 3DVAR are benefited from its flow-dependent background error, resulting in more realistic depiction of sea surface wind for the widespread-fog case and better moisture distribution for the other case in the initial conditions. More importantly, the correlation between temperature and humidity in the background error of EnKF plays a vital role in the response of moisture to the assimilation of temperature, which leads to a great improvement on the initial moisture conditions for sea fog forecast.

Abstract: The frequency and intensity of air pollution are two of most critical issues the world faces in dealing with global environmental problems. They are both important areas that need to be improved. Our previous research [20] examines the assessment of fine dust pollution in Baekryeong island by statistical reasoning through one specific example of inland city (Yanggu) in Republic of Korea; however, given that Baekryeong Island is a remote island, there has been little focus on in-depth examination of its effect on the high density of fine dust in Baekryeong Island. The purpose of this article is twofold: (i) to examine the effect of a remote island on the high density of fine dust on Baekryeong Island using statistical reasoning and to provide a more specific statistical basis for the claim that one of the non-negligible factors influencing the high density of fine dust on Baekryeong Island is the geographic proximity to China; and (ii) to present brief discussion of fundamental cause of fine dust and global air pollution issues, which are not discussed in [20].

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

The precise prediction of air contaminant dispersion is essential to the air quality monitoring and the emergency management of the contaminant gases leakage incidents in the chemical industry park. The conventional atmospheric dispersion models can seldom give precise prediction due to inaccurate input parameters. In order to improve the prediction accuracy of dispersion model, two data assimilation methods (i.e. one is merely based on the typical particle filter while the other is a combination of particle filter and expectation-maximization algorithm) are proposed to assimilate the UAV observations into the atmospheric dispersion model. Two emission cases are taken into consideration, the difference between which is the different dimensions of state variables. To test the performances of the proposed methods, experiments corresponding to the two emission cases are designed and implemented. The results show that the particle filter can effectively estimate the model parameters and improve the accuracy of model prediction when the dimension of state variables is low. In contrast, when the dimension of state variables becomes higher, the method of particle filter combining expectation-maximization algorithm performs better in the parameter estimation accuracy and warm-up time. Therefore, the data assimilation methods are able to effectively support the air quality monitoring and emergency management in chemical industry parks.

The primary measure of the quality of sea surface temperature (SST) fields obtained from satellite-borne infrared sensors has been the bias and variance of matchups with co-located in-situ values. Because such matchups tend to be widely separated, these bias and variance estimates are not necessarily a good measure of small scale (several pixels) gradients in these fields because one of the primary contributors to the uncertainty in satellite retrievals is atmospheric contamination, which tends to have large spatial scales compared with the pixel separation of infrared sensors. Hence, there is not a good measure to use in selecting SST fields appropriate for the study of submesoscale processes and, in particular, of processes associated with near-surface fronts, both of which have recently seen a rapid increase in interest. In this study, two methods are examined to address this problem, one based on spectra of the SST data and the other on their variograms. To evaluate the methods, instrument noise was estimated in Level-2 VIIRS and AVHRR SST fields of the Sargasso Sea. The two methods provided very nearly identical results for AVHRR: along-scan values of approximately 0.18 K for both day and night and along-track values of 0.21 K also for day and night. By contrast, the instrument noise estimated for VIIRS varied by method, scan geometry and day-night. Specifically, daytime, along-scan (along-track), spectral estimates were found to be approximately 0.05 K (0.08 K) and the corresponding nighttime values of 0.02 K (0.03 K). Daytime estimates based on the variogram were found to be 0.08 K (0.10 K) with the corresponding nighttime values of 0.04 K (0.06 K). Taken together: AVHRR instrument noise is significantly larger than VIIRS instrument noise, along-track noise is larger than along-scan noise and daytime levels are higher than nighttime levels. Given the similarity of results and the less stringent preprocessing requirements, the variogram is the preferred method although there is a suggestion that this approach overestimates the noise for high quality data in dynamically quiet regions. Finally, simulations of the impact of noise on the determination of SST gradients show that on average the gradient magnitude for typical ocean gradients will be accurately estimated with VIIRS but substantially overestimated with AVHRR.

This study investigated the risk of lung and bladder cancers in people residing in proximity of a coal-oil-fired thermal power plant in an area of north-eastern Italy, covered by a population-based cancer registry. Incidence rate ratios (IRR) by sex, age, and histology were computed according to tertiles of residential exposure to benzene, nitrogen dioxide (NO2), particular matter, and sulfur dioxide (SO2) among 1076 incident cases of lung and 650 cases of bladder cancers. In men of all ages and in women under 75 years of age, no significant associations were observed. Conversely, in women aged >75 years significantly increased risks of lung and bladder cancers were related to high exposure to benzene (IRR for highest vs. lowest tertile: 2.00 for lung cancer and 1.94 for bladder cancer) and NO2 (IRR: 1.72 for lung cancer; and 1.94 for bladder cancer). In these women, a 1.71-fold higher risk of lung cancer was also related to a high exposure to SO2. The findings of this descriptive study indicated that air pollution may have a role with regard to the risk of lung and bladder cancers, limited to women aged ≥ 75 years. Such increased risk warrants further analytical investigations.

Vacuum drying can dehydrate materials further than dry heat methods while protecting sensitive materials from thermal degradation. Many industries have shifted to vacuum drying as cost- or time-saving measures. Small-scale vacuum drying, however, has been limited by high costs of specialty scientific tools. To make vacuum drying more accessible, this study provides design and performance information for a small-scale open source vacuum oven, which can be fabricated from off-the-shelf and 3-D printed components. The oven is tested for drying speed and effective-ness on both waste plastic polyethylene terephthalate (PET) and a consortium of bacteria developed for bioprocessing of terephthalate wastes to assist in distributed recycling of PET for both additive manufacturing as well as potential food. Both materials can be damaged when exposed to high temperatures, making vacuum drying a desirable solution. The results showed the open source vacuum oven was effective at drying both plastic and biomaterials, drying at a higher rate than a hot-air dryer for small samples or for low volumes of water. The system can be constructed for less than 20% of commercial vacuum dryer costs for several laboratory-scale applications including dehydration of bio-organisms, drying plastic for distributed recycling and additive manufacturing, and chemical processing.

Repeated air pollution exposure is one of the major threats to skin health. Air pollution causes skin damage and accelerates skin ageing mainly through oxidative stress mechanisms. Since it is difficult to minimize skin exposure from air pollutants, especially in urban areas, strategies to protect the skin are needed. On the other hand, plant phenolic compounds have been found to be effective in attenuating cellular oxidative stress and inflammation induced by different air pollutants. Therefore, we conducted a 12-week randomized, placebo-controlled, double blind study to assess the efficacy of a polyphenol-enriched dietary supplement (comprised of olive leaf, lemon verbena, rosemary and Sophora japonica extracts) in reducing pollution-induced oxidative stress and in improving different skin parameters related to skin ageing of Caucasian and Asian volunteers living in a polluted urban European area (Milan). One hundred healthy women were recruited and randomized in the placebo or in the test dietary supplement treatment arms. To assess the efficacy of the dietary supplement, the total antioxidant capacity on saliva (FRAP) was determined, as well as the oxidative damage on skin (lipoperoxides content), the skin moisture (corneometry), the trans-epidermal water loss (Tewameter), the skin radiance and the skin colour, (spectrophotometry), the skin elasticity (cutometry), the skin sebum content (sebumeter), and the skin roughness (image analysis). As a result, both inter-group and intra-group analysis proved that the dietary supplement improved all clinical and biochemical monitored parameters, in both Caucasian and Asian individuals. In conclusion, the results of the study indicate a reduced oxidative stress-induced skin damage in both Asian and Caucasian women living in a polluted urban area.

Coastal inundation is an increasing problem. Sea-level rise will greatly increase the frequency and depth of inundation, forcing vulnerable communities to adapt. Communities will need to decide when and how to adapt. The process of decision-making along adaptive pathways is now being used internationally to plan for adaptation over time by anticipating decision points in the future however it unfolds. This process requires risk and uncertainty considerations to be transparent in the scenarios used in such planning. We outline a framework for uncertainty identification and management within coastal hazard assessments which recognizes different types of decision and identifies the types of uncertainty that must be accounted for, such as statistical, scenario and deep uncertainty types. We show how coastal-inundation hazard can be mapped and presented in a way that clearly separates sources of uncertainty, so that they are transparent within a dynamic adaptive pathways planning process. Traditional coastal inundation maps show inundated area only. We present maps of inundation depth and frequency which clearly show the degree of exposure, where that exposure occurs, and how much sea-level rise can be tolerated. The new uncertainty framework and mapping techniques can better identify decision points and their expected time range, which provides more useful input to the adaptation process than traditional coastal inundation assessments.

When it comes to air pollution complaints, odours are often the most significant contributor. Sources of odour emissions range from natural to anthropogenic. Mitigation of odour can be challenging, multifaceted, site-specific, and is often confounded by its complexity—defined by existing (or non-existing) environmental laws, public ordinances, and socio-economic considerations. The objective of this paper is to review and summarize odour legislation in selected European countries (France, Germany, Austria, Hungary, United Kingdom, Spain, The Netherlands, Italy, Belgium), North America (USA and Canada), South America (Chile and Colombia), as well as Oceania (Australia and New Zealand) and Asia (Japan, China). Many countries have incorporated odour controls into their legislation. However, odour-related assessment criteria tend to be highly variable between countries, individual states, provinces and even counties and towns. Legislation ranges from (1) no specific mention in environmental legislation that regulates pollutants which are known to have an odour impact to (2) extensive details about odour source testing, odour dispersion modeling, ambient odour monitoring, (3) setback distances, (4) process operations, and (5) odour control technologies and procedures. Agricultural operations are one specific source of odour emissions in rural and suburban areas and a model example of such complexities. Management of agricultural odour emissions is important because of the dense consolidation of animal feeding operations and the advance of housing development into rural areas. Overall, there is a need for continued survey, review, development, and adjustment of odour legislation that considers sustainable development, environmental stewardship, and socio-economic realities, all of which are amenable to a just, site-specific, and sector-specific application.

This review chronicles the indirect transmission method which seems to be overlooked by most people and makes attempts to clearly document the various transmission ways with a hope that such information may strengthen the knowledge base of researchers towards methods of eradicating the pandemic. Current knowledge of transmission and exposure of SARS-CoV-2 has been explained. Various researchers have put forward different ways of exposure and transmission. Literature does not reveal whether the indirect transmission route is the dominant one. However total lockdown could be a veritable means to reduce both direct and indirect transmission routes. In many countries where the indirect transmission has been reduced, the scourge of the virus is less. The work creates awareness on the need to watch out for those routes of transmissions that may not be popular and suggested key knowledge gaps that needs to filled.

This study inscribes itself in the global discussion on the nurturing of pro-environmental behaviors among young people for a sustainable future. Here we focus on students' interest in Ecosystem Services and Sustainability to explain their awareness and optimism about the environmental issues of air pollution, water shortage and green gas emission in 50 countries around the world. To this end, we use the cross-sectional survey data of the OECD's Program for International Student Assessment (PISA) 2015, along with seemingly unrelated bi-variate weighted ordered Probit modeling with country specific effects. The results show that in addition to factors such as age, gender, immigration status, and economic, social and cultural status, interest in the biosphere is a significant determinant of students' environmental awareness and optimism. In fact, a one level increase in students' interest in ecosystem services and sustainability raises on average their awareness level by 15.3% for the issue of air pollution, 15.7% for the issue of water shortage, and 24.6% for the issue of green gas emission. Although students' interest in the biosphere seems to not have a significant effect on their expectations about the issue of green gas emission, it does however raise their level of optimism by 0.8% for the issue of air pollution, and 0.2% for the issue of water shortage. Furthermore, every one level increase in students' environmental awareness leads to 17.3% more optimism about the issue of air pollution, 15.8% more optimism about the issue of water shortage, and 17.4% more optimism about the issue of green gas emission. Therefore, relying on the Theory of Planned Behavior (TPB), our results imply that governments and policy makers can successfully leverage young people interests in the biosphere to effectively achieve their goals for sustainability.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

This paper presents a new scientific contribution on the two-dimensional (2-D) subdomain technique in polar coordinates taking into account the finite relative permeability of the ferromagnetic material. The constant relative permeability corresponds to linear part of the nonlinear B(H) curve. As in conventional technique, the method of separation of variables and the Fourier’s series are used for the resolution of magnetostatic Maxwell’s equations in each region. Although, the general solutions of magnetic field in the subdomains and boundary conditions (BCs) between regions are different in the conventional and proposed method. In this later, the magnetic field solution in each subdomain is a superposition of two magnetic quantities in the two directions (i.e., r- and Q-axis) and the BCs between two regions are also in both directions. For example, the scientific contribution has been applied to an air- or iron-cored coil supplied by a constant current. The distribution of local quantities (i.e., the magnetic vector potential and flux density) has been validated by a corresponding 2-D finite-element analysis (FEA). The obtained semi-analytical results are in very good agreement with those of numerical method.

With forty years of developments, bio-macromolecule cryo-electron microscopy has met its revolution of resolution and is playing a very important role in structural biology study. According to different specimen states, cryo-electron microscopy (cryo-EM) involves three specific techniques, single particle analysis (SPA), electron tomography and sub-tomogram averaging, and electron diffraction. All these three techniques have not realized their full potentials of solving structures of bio-macromolecules and therefore need to be developed in the future. In this review, the current existing bottlenecks of cryo-EM SPA are discussed with theoretical analysis, which includes air-water interface during specimen cryo-vitrification, bio-macromolecular conformational heterogeneity, focus gradient within thick specimen, and electron radiation damage. Besides, potential solutions of these bottlenecks are proposed and discussed, which are worthy of further investigations in the future.

Epiphytic lichens are well-known indicators of air contamination. The chemical composition of lichens is affected by the concentration of pollutants in the environment. Usually, researchers assess long-term variations in trace elements or other pollutants in the study area or identify the spatial features of air contamination. The aim of this study is to create a database of trace element concentrations in the samples of the epiphytic lichen Hypogymnia physodes growing in the Kaliningrad region. The database can be used as a ‘reference point’ for monitoring studies. Another objective is to identify the spatial patterns of iron, manganese, nickel, cadmium, silver, lead, strontium, rubidium, and calcium in the Kaliningrad region. The samples of wild lichens were collected from pine and birch trees 1.2-1.8 m from the bases of the threes, using a regular grid, in August 2010. One-two-year-old thalli were used in the chemical analysis. The metals Ag, Cd, Cu, Pb, Ni, Fe, Mn, and Zn were determined by AAS (Mn, Fe by flame AAS and the others by ETA-AAS) and the elements Sr, Rb, and Ca by X-ray fluorescence. The concentration of metals in the western coastal area (the Sambian or Kaliningrad Peninsula) is higher than it is in the central and eastern parts of the region. Principal component factor analysis was carried out to detect and characterise different pollution sources and to identify the most polluted areas. The factors of metal emission were described. The authors examined the features of the spatial distribution of trace elements. Prevailing winds are form south-west. Therefore, the highest concentrations of trace elements were found on the Sambian peninsula and on the coasts of the Vistula and Curonian Lagoons. The high concentrations of trace elements in the samples of the lichen H.physodes, which were observed in the coastal part of the region, are associated with human impact and subsequent pollution. The chemical composition of lichens on the Sambian peninsula may have developed under the impact of both local pollution sources – vehicles, thermal energy facilities, and ports – and such factors as transboundary traffic and sea spray.

Environmental legislation is moving towards global standards for ease of application and to impose sanctions and penalties when necessary, without compromising human health and biota. International environmental measures for control and monitoring of atmospheric air only monitor emissions of SO_x, NO_x, O₃, and Pb. In general, most research work in air pollution done using the analysis of elements in rainwater show analysis of trace metals such as Na, Mg, Zn, and Mn. In this work, trace metals in the rainwater at the city of Goiânia, capital of the State of Goiás, were analyzed. Goiânia is a large city set in a predominantly agricultural province located in central Brazil. Presence of trace metals in rainwater was detected, indicating atmospheric air pollution levels higher than occupational limits set by WHO.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

Many reported sea level records are often not a single measurement. They are then a composition of different records from several tide gauges. Sometimes, they are from the same tide gauge, but the tide gauge stability has been affected by earthquakes. This is the case of Guam as discussed in the present manuscript. The claimed sea level acceleration of Guam is only the result of two earthquakes that have compromised the stability of the tide gauge.

The conservation of coastal wetland ecosystems, like mangrove forests and salt marshes, represents a critical strategy for mitigating atmospheric emissions and climate change in the 21st century. Yet the existence of these environments is threatened by human-induced disturbances, namely deforestation and accelerated sea-level rise. Coastal systems maintain surface elevation in response to sea-level rise through a combination of physical and biological processes both above and below the ground surface. The quantification and relative contribution of belowground process controls (e.g., seasonal water content, organic matter decomposition) on surface elevation change is largely unexplored but crucial for informing coastal ecosystem sustainability. To address this knowledge deficit, we integrated measurements of surface elevation change of the live root zone (0.5 to 1 m depth) with geotechnical data from co-located sediment cores in the Sundarbans mangrove forest (SMF) of southwest Bangladesh. Core data reveal that the primary belowground controls on surface elevation change include seasonal fluctuations in pore-water content and the relative abundance of fine-grained sediments capable of volumetric expansion and contraction, supporting an elevation gain of ~2.42 ± 0.26 cm yr⁻¹. In contrast to many mangrove environments, the soils of the SMF contain little organic matter and are dominantly composed (>90%) of inorganic clastic sediments. The mineral-rich soil texture likely leads to less compaction-induced subsidence as compared to organic-rich substrates and facilitates surface equilibrium in response to sea level rise. Despite a relatively high soil bulk density, soil carbon (C) density of the SMF is very low owing to the dearth of preserved organic content. However, rates of C accumulation are balanced out by locally high accretion rates, rendering the SMF a greater sink of terrestrial C than the worldwide mangrove average. The findings of this study demonstrate that C accumulation in the SMF, and possibly other alluvial mangrove forests, is highly dependent on the continued delivery of sediment to the mangrove platform and associated settings.

Reinforcement learning is used for air combat problems in recent years, and the idea of curriculum learning is often used for reinforcement learning, but traditional curriculum learning suffers from the problem of plasticity loss in neural networks. Plasticity loss is the difficulty of learning new knowledge after the network has converged. To this end, we propose a motivational curriculum learning distributed proximal policy optimization (MCLDPPO) algorithm, through which agents trained can significantly outperform the predictive game tree and mainstream reinforcement learning methods. The motivational curriculum learning is to help the agent gradually improve their combat ability by observing the agent's unsatisfactory performance and providing corresponding rewards as a guide. Additionally, a complete tactical maneuver is encapsulated based on existing air combat knowledge, and through the flexible use of these maneuvers, some tactics beyond human knowledge can be realized. In addition, we designed an interruption mechanism for the agent to increase the frequency of decision-making when the agent faces an emergency. When the number of threats the agent receives changes, the current action will be interrupted to reacquire observations and make decisions again. Using the interruption mechanism can significantly improve the ability of the agent. To simulate actual air combat better, we built an air combat environment based on digital twin technology to create an air combat engine core such as missiles and radars. Based on this environment, we develop a distributed intelligent training system that employs Redis as the cache and obtains the data generated in the distributed environment through a multi-threaded TCP/IP protocol, which significantly increases the training data throughput and helps the agent accelerates convergence. The experimental results demonstrate that the agent can fully exploit the situational information to make reasonable decisions and affords air combat tactical adaption, verifying the effectiveness of the algorithmic framework proposed in this paper.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

Aero submarines (aerosubs) are vehicles that can both fly both in air and travel under water. The concept of dual aerial and aquatic vehicles emerged in 1939 when Russian engineer Boris Ushakov proposed the “flying submarine”[1], and this was followed by further developments including RFS1 [2], convair project in 1964[3] , etc. however, to date, limited attempt has been diverted towards the advanced development of such aircraft. This is heavily influenced by challenges associated with the design and operation of the same. Based on the review of literature the authors aim to introduce a theoretical design for an aerosub (QFS-20) with a view to address the design and operation issues including power, entry to and exit from water.

The reaction kinetics of burnt lime (CaO) in contact with sea water has been elucidated and compared to its behaviour in fresh water. In the first minutes of contact between burnt lime and water, it "slaked" as CaO reacted with water to yield calcium hydroxide (Ca(OH)2). Subsequently, calcium hydroxide reacted with magnesium, sulphate and carbonate from the sea water to yield magnesium hydroxide (Mg(OH)2), calcium sulphate dihydrate (gypsum, CaSO4·2H2O) and calcium carbonate (CaCO3), respectively. In a closed system of 1% CaO in natural sea water (where the supply of sulphate, magnesium and carbonate is limited), more than 90% reacted within the first 5 hours. It is foreseen that in an open system, like a marine fjord, it will react even faster. The pH 8 of sea water close to the CaO particle surface will immediately increase to a theoretical value of about 12.5 but will, in an open system with large excess of sea water, rapidly fall back to pH 10.5 being equilibrium pH of magnesium hydroxide. This is further reduced to < 9 due to the common ion effect of dissolved magnesium in sea water and then be diluted to the sea water background pH, about 8. Field test dosing CaO particles to sea water showed that the pH of water between the particles stayed around 8.

In this paper, we focus on developing a novel method to extract sea ice cover (i.e., discrimination/classification of sea ice and open water) using Sentinel-1 (S1) cross-polarization (vertical-horizontal, VH or horizontal-vertical, HV) data in extra wide (EW) swath mode based on the machine learning algorithm support vector machine (SVM). The classification basis includes the S1 radar backscatter coefficients and texture features that are calculated from S1 data using the gray level co-occurrence matrix (GLCM). Different from previous methods where appropriate samples are manually selected to train the SVM to classify sea ice and open water, we proposed a method of unsupervised generation of the training samples based on two GLCM texture features, i.e. entropy and homogeneity, that have contrasting characteristics on sea ice and open water. We eliminate the most uncertainty of selecting training samples in machine learning and achieve automatic classification of sea ice and open water by using S1 EW data. The comparison shows good agreement between the SAR-derived sea ice cover using the proposed method and a visual inspection, of which the accuracy reaches approximately 90% - 95% based on a few cases. Besides this, compared with the analyzed sea ice cover data Ice Mapping System (IMS) based on 728 S1 EW images, the accuracy of extracted sea ice cover by using S1 data is more than 80%.

A checklist of parasitic cymothoids from Malaysian waters is presented based on available literature and material collected from 2010 to 2020. Most of the collected specimens were recorded from waters of Terengganu, east coast of Peninsular Malaysia (facing South China Sea), whereas literature records were represented from Sarawak, along the Miri coast of northwest Borneo. The checklist comprises 18 species under 10 genera, seven of which are new records from Malaysia, which includes Anilocra nemipteri Bruce, 1987; Ceratothoa barracuda Martin, Bruce and Nowak, 2015; Ceratothoa carinata (Bianconi, 1869); Cymothoa epimerica Avdeev, 1979; Elthusa sigani Bruce, 1990; Joryma engraulidis (Barnard, 1936) and Renocila richardsonae Williams and Bunkley-Williams, 1992. Eight new host records are based on collected specimens: Anilocra nemipteri was dorsally attached on Nemipterus nemurus (Bleeker 1857), Nemipterus nematophorus (Bleeker 1854), Nemipterus tambuloides (Bleeker 1853), and Nemipterus thosaporni Russell 1991 (family Nemipteridae); Ceratothoa carinata was found in the buccal cavity of Decapterus macrosoma Bleeker 1851 (family Carangidae); Cymothoa eremita (Brunnich, 1783) was attached in the buccal cavity of Nemipterus tambuloides and Nemipterus furcosus (Valenciennes 1830); Elthusa sigani was found attached on Pterois russelli Bennett 1831 (family Scorpaenidae); and Renocila richardsonae was attached on the caudal fin of Upeneus japonicus (Houttuyn 1782) (family Mullidae). All cymothoid species listed here are known to have a Central Indo Pacific distribution, with some ranging as far as the western Indian Ocean. The cymothoid-host association is here listed from 28 fish families, with the most common reported from Carangidae (pompanos, jack mackerels, runners, scads), Engraulidae (anchovies) and Leiognathidae (ponyfishes, slipmouths). This paper is the first comprehensive treatment to update both verified literature data and deposited specimens, with a key for the family Cymothoidae in Malaysian waters.

Abstract: Air-polishing with low abrasiveness powders is fats arising as a valid and mini-invasive instrument for the management of biofilm colonizing dental implants. The reported advantage is the efficient removal of plaque with respect of the titanium integrity. In the present study, we evaluated the in-situ plaque-removal and continual the post-treatment anti-bacterial efficacy of an innovative erythritol/chlorhexidine air-polishing powder and compared it with sodium bicarbonate. Two peri-implantitis-linked biofilm formers strains Staphylococcus aureus and Aggregatibacter actinomycetemcomitans were selected and used to infect titanium disks before and after the air-polishing treatment. Cells number and viability were assayed by colonies forming units (CFUs) count and metabolic-colorimetric (2,3-Bis-(2-Methoxy-4-Nitro-5-Sulfophenyl)-2H-Tetrazolium-5-Carboxanilide) (XTT) assay. Air-polishing performed with either sodium bicarbonate or erythritol/chlorhexidine was effective in reducing bacteria biofilm viability and number onto pre-infected specimens, while erythritol/ chlorhexidine showed a higher post-treatment biofilm re-growth inhibition. Surface analysis via mechanical profilometry failed to show an increase in titanium roughness, regardless of the powder selected.

An important aspect of the new sustainable development goals (SDGs) is a greater emphasis on reducing the health impacts of urban ambient air pollution (AAP) in developing countries. Meanwhile, the burden of disease attributable to AAP in sub-Saharan Africa (SSA) is growing, yet estimates of its impact in the region are likely underestimated due to a lack of air quality monitoring, the paucity of epidemiological studies, and important population vulnerabilities in the region. The lack of studies in the SSA region also represents an important global health disparity and environmental justice issue because thousands of air pollution health effects studies have been conducted in Europe and North America rather than in some of the most polluted regions of the world, such as SSA. In this review, we synthesize all of the ambient air pollution epidemiological studies that have been conducted in SSA to date. We highlight the gaps in AAP epidemiological studies conducted in different sub-regions of SSA and provide methodological recommendations for future environmental epidemiology studies addressing AAP in the SSA region.

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.

Oil spills are adverse events that may be very harmful to ecosystems and food chain. In particular, large sea oil spills are very dramatic occurrence often affecting sea and coastal areas. Therefore the sustainability of oil rig infrastructures and oil transportation via oil tankers are linked to law enforcement based on proper monitoring techniques which are also fundamental to mitigate the impact of such pollution. Within this context, in this study a meaningful showcase is analyzed using remotely sensed measurements collected by the Synthetic Aperture Radar (SAR) operated by the COSMO-SkyMed (CSK) constellation. The showcase presented refers to the Deepwater Horizon (DWH) oil incident that occurred in the Gulf of Mexico in 2010. It is one of the world's largest incidental oil pollution event that affected a sea area larger than 10,000 km². In this study we exploit, for the first time, dual co-polarization SAR data collected by the Italian CSK X-band SAR constellation showing the key benefits of HH-VV SAR measurements in observing such a huge oil pollution event, especially in terms of the very dense revisit time offered by the CSK constellation.

Mineral dust is one of the most important aerosol in mass over the world, affecting health and dynamics. This aerosol is mainly emitted over arid areas but may be long-range transported, impacting the local budget of air quality in many cities. While models were extensively used to study a single specific event, or making a global analysis at coarse resolution, the goal of our study is to simultaneously focus on several areas - Europe, North America, Central Asia, East China and the Caribbean area - for a one month period, March 2014, avoiding any parameter fitting to better simulate a given dust outbreak. The simulation is performed for the first time with the hemispheric version of the CHIMERE model, with a horizontal resolution of 10km. In this study, an overview of several simultaneous dust outbreaks over the north hemisphere is proposed to assess the capability of such modelling tools to predict dust pollution events. A quantitative and qualitative evaluation of the most striking episodes is presented with comparisons to satellite data, ground based Particulate Matter and calcium measurements. Despite some overestimation of dust concentrations far from emission areas, the model is able to simulate the timing of the arrival of dust outbreaks on observational sites. For instance, several spectacular dust storms in the US and China are perfectly captured by the models. The high resolution allows to better describe and understand the orographic effects and the long-range transport of dust plumes.

Three genera of very large volant birds existed for most of the Pliocene: the Pelagornithidae seabirds; the large North American Teratornithidae and the stork Leptoptilos falconeri in Africa and Asia. All became extinct around 3 Ma. The reasons for their demise are puzzling, as the Pelagornithidae had a world-wide evolutionary history of more than 50 Ma, smaller teratorns were still extant in the Holocene and smaller stork species are still globally extant. Extant large birds have a common critical takeoff airspeed suggesting a biomechanical limit in terms of power, risk and launch speed, and simulations of the flight of these extinct species suggest that at 1 bar they would have exceeded this value. Estimates for the Late Pliocene atmospheric density are derived from marine and terrestrial isotopes as well as resin chemistry, both approaches suggesting a value of about 1.2 bar, which drops to present levels during the period 3.3 to 2.6 Ma, thus a loss in atmospheric density may have caused biomechanical and ecological stress contributing to their extinction and/or development of smaller forms. This hypothesis is examined in terms of a possible mechanism of atmospheric mass loss and how this would be seen in the geological record. At 1.2 bar all the extinct species present takeoff airspeeds similar to large extant volant birds and which match the expected power and kinetic energy levels.

As air traffic demand grows, robust, data-driven anomaly detection methods are required to ensure that aviation systems become safer and more efficient. The terminal airspace is identified as the most critical airspace for both individual flight-level and system-level safety and efficiency. As such, developing data-driven anomaly detection methods to analyze terminal airspace operations is paramount. With the expansion of ADS-B technology, open-source flight tracking data has become more readily available to enable larger-scale analyses of aircraft operations. This paper makes a distinction between spatial metrics in ADS-B trajectory data and energy metrics derived from ADS-B trajectory data. Motivated by the limited number of approaches that simultaneously consider both spatial and energy metrics, this paper introduces the concepts of spatial anomalies and energy anomalies. In particular, it proposes a novel, unified framework for detection of spatial and energy anomalies in ADS-B trajectory data (and associated derived metrics). The framework consists of three main parts - a data processing procedure, a spatial anomaly detection method, and an energy anomaly detection method. The framework is demonstrated utilizing four months of ADS-B trajectory data associated with arrivals at San Francisco International Airport, and the relationship between the spatial and energy anomalies in this terminal airspace is explored. The results that stem from the implementation of this framework indicate that if an aircraft is spatially not conforming to an identified set of air traffic flows representing standard spatial operations, then this aircraft is more likely to experience non-conformance to standard operations in its energy metrics. Aviation operators, such as air traffic controllers, may benefit from this observation, as it may factor into decision-making in instances where there is the potential to instruct an aircraft to spatially deviate from standard operations. Additionally, this research revealed underlying differences between trajectories that are spatially nominal yet energy-anomalous and those trajectories that are spatially anomalous and energy-anomalous. Focusing solely on energy anomaly detection does not provide insight into potential spatial-related decisions that may have been made to result in off-nominal energy behavior.

Solving environmental odor issues can be confounded by many analytical, technological, and socioeconomic factors. Considerable know-how and technologies can fail to properly identify odorants responsible for the downwind nuisance odor and mitigate it for the affected citizenry. We propose enabling solutions to environmental odor issues by utilizing troubleshooting techniques developed for the food, beverage, and consumer products industries. We showed that the downwind odorant impact-priority ranking process can be definable and relatively simple. The initial challenge is the prioritization of environmental odor character from the perspective of the impacted citizenry downwind. In this research, we aim at summarizing three natural models of the rolling unmasking effect (RUE) and discuss them more systematically in the context of the proposed downwind environmental odor prioritization approach. Regardless of the size and reach of an odor source, a simplification of odor character and composition typically develops with downwind dilution. The extreme odor simplification-upon-dilution was demonstrated for two plant varieties, prairie verbena and Virginia pepperweed. Their downwind odor frontal boundaries were dominated by single, character-defining odorants; p-cresol-dominated ‘barnyard’ odor, and benzyl mercaptan-dominated ‘burnt match’ odor, respectively. The P.T. porcupine downwind odor frontal boundary was dominated by two potent, character-defining odorants: (1) ‘onion’/‘body odor’ odorant #1 and (2) ‘onion’/‘grilled’ odorant #2. In contrast with their downwind boundary simplicities, each odor source presented considerable compositional complexity and composite character difference near the source. The proposed RUE approach’s ultimate significance is the illustration of naturally occurring phenomena that explain why some environmental odors and their sources can be challenging to identify and mitigate using the analytical only approach (focused on compound identities and concentrations). These approaches rarely move beyond comprehensive lists of compounds being emitted by the source.

Air quality has been a major concern throughout the world, Nigeria inclusive. The monitoring of air quality involves indoor and outdoor air quality. In this study, our concern was on indoor air quality. The aim of this study was to assess the air quality of residential homes (17), classrooms (3), hospitals (2), offices (5), Shops (2), and laboratories (5) in Akure, Nigeria in terms of formaldehyde (HCHO), total volatile organic compound (TVOC), Particulate matter (PM_1.0; PM_2.5, and PM₁₀). A Multifunction Air Detector was used for the assessment using the manufacturers’ procedures and the locations were identified using a Mini GPS. The results revealed as follows: HCHO (0.001-0.030 mg/m³), TVOC (0.003-362 mg/m³), PM_1.0 (004-014 µg/m³), PM_2.5 (006-020 µg/m³), and PM₁₀ (006-022 µg/m³). The results obtained were below the 24 h pollution recommended standards (0.1 mg/m³- HCHO; TVOC; 10-20 μ/m³ PM) of EPA and WHO. Statistically, there were correlations within the pollutants and weather. The Indoor air quality (IAQ) depicted the areas as ‘good,’ and toxicity potential (TP) were below unity. Although the locations looked safe, it is recommended that constant monitoring of the indoors should be ensured and proper ventilation should be provided.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

Rapid urbanization, increasing population and increased industrialization to cater to demands of the growing population has imposed upon us a huge environmental cost. The significantly deteriorated air quality across the globe is associated with a direct and indirect impact on public health. While associated disorders such as chronic obstructive pulmonary diseases, heart failures are well documented, less is known about the biological basis of the process. We hypothesize that the worsening air quality may likely impact common systemic inflammatory processes, thus driving communicable and non-communicable diseases alike.Receptor mediated entry of particulate matter (PM2.5) results in activation of signaling cascades which culminate in production of inflammatory chemokine and cytokine responses, traversing through the blood mediating impacting not only on other organs but also dysbiosis of microflora. For the purpose of the review we choose tuberculosis (TB) as a model for communicable infectious disease and type 2 diabetes mellitus (T2DM) as a marker for non-communicable disorder. The increasing prevalence of these co-morbidities and the burdening of public health systems justifies this example. However the hypothesis may be applicable to other inflammation driven disorders also.

The Greenland Ice Sheet is now the largest land ice contributor to global sea level rise, largely driven by increased surface meltwater runoff from the ablation zone, i.e. areas of the ice sheet where annual mass losses exceed gains. This small but critically important area of the ice sheet has expanded in size by ~50% since the early 1960s, and satellite remote sensing is a powerful tool for monitoring the physical processes that influence its surface mass balance. This review synthesizes key remote sensing methods and scientific findings from satellite remote sensing of the Greenland Ice Sheet ablation zone, covering progress in 1) radar altimetry, 2) laser (lidar) altimetry, 3) gravimetry, 4) multispectral optical imagery and, 5) microwave and thermal imagery. Physical characteristics and quantities examined include surface elevation change, gravimetric mass balance, reflectance, albedo, and mapping of surface melt extent and glaciological facies and zones. The review concludes that future progress will benefit most from methods that combine multi-sensor, multi-wavelength, and cross-platform datasets designed to discriminate the widely varying surface processes in the ablation zone. Specific examples include fusing laser altimetry, radar altimetry, and optical stereophotogrammetry to enhance spatial measurement density, cross-validate surface elevation change, and diagnose radar elevation bias; fusing optical imagery, radar imagery, and microwave scatterometry to discriminate between snow, liquid water, refrozen meltwater, and bare ice near the equilibrium line altitude; combining optical reflectance with laser altimetry to map supraglacial lake, stream, and crevasse bathymetry; and monitoring the inland migration of snowlines, surface melt extent, and supraglacial hydrologic features.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

A real-time two-way direct load control (TWDLC) of central air-conditioning chillers in wide area is proposed to provide demand response. The proposed TWDLC scheme is designed to optimize the load shedding ratio of every customer under control to ensure the target load to be shed is met at every scheduling period. In order to overcome the load reduction uncertainties of TWDLC, an innovative solution is proposed by applying a certain degree of loosening on the constraint of the actual shed load. Fuzzy linear programming is utilized to solve the optimization problem with fuzzy constraints. The proposed fuzzy linear programming problem is solved by delicately transforming it into a regular liner programming problem. A selection scheme used to obtain the feasible candidates set for load shedding at every sampling interval of TWDLC is also designed along with the fuzzy linear programming.

Here, we report on ZnO nanoparticles (NPs) generated by nanosecond pulsed laser (Nd:YAG, 1064 nm) through ablation of metallic Zn target in water and air and their comparative analysis as potential nanomaterials for biomedical applications. The prepared nanomaterials were carefully characterized in terms of their structure, composition, morphology and defects. It was found that in addition to the main wurtzite ZnO phase, which is conventionally prepared and reported by others, the sample laser-generated in air also contained some amount of monoclinic zinc hydroxynitrate. Both nanomaterials were then used to modify model wound dressings based on biodegradable poly-L-lactic acid. The as-prepared model dressings were tested as biomedical materials with bactericidal properties towards S. aureus and E. coli strains. The advantages of the NPs prepared in air over their counterparts generated in water found in this work are discussed.

Abstract: Predation of eggs and emerging hatchlings of olive ridley turtle (Lepidochelys olivacea) by wild animals and feral dogs are known. They reduce the hatching success rate considerably affecting the conservation management of this vulnerable species. Hatchery management is practised in India to overcome predation. Ant predation is a serious threat to turtle nest protected by ex situ or in situ erected hatchery. This article reports the first direct evidence of turtle eggs predation by Dorylus orientalis Westwood, 1835 commonly called red ants. Native to India, Oriental, Indo Australian and Palearctic regions they are notorious as an agricultural pest. Chlorpyrifos pesticides recommended for their control could become fatal for the developing embryos of turtles if applied near the hatchery. In the turtle nesting site of the west coast of India, D. orientalis has more of an ecological role than as a pest. Natural pesticide such as Neem powder (Azadirachta indica) shows promising results for preventing their infestation.

A new coronavirus (SARS-CoV-2) have determined a pneumonia outbreak in China (Wuhan and Hubei) on December 2019. While pharmaceutical and non-pharmaceutical intervention strategies are strengthened worldwide, the scientific community has been studying the risk factors associated with SARS-Cov-2, to enrich epidemiological information. For a long time, before the industrialized era, air pollution has been a real and big health concern and it is today a very serious environmental risk for many diseases and anticipated deaths in the world. It has long been known that air pollutants increasing the invasiveness of pathogens for humans by acting as a carrier and making people more sensitive to pathogens through a negative influence on the immune system. Based on scientific evidences, the hypothesis that air pollution, resulting from a combination of factors such as meteorological data, level of industrialization as well as regional topography, can acts both as an infection carrier as a harmful factor of the health outcomes of COVID-19 disease has been raised recently. This hypothesis is turning in scientific evidence, thanks to the numerous studies that have been launched all over the world. With this review, we want to provide a first unique view of all the first epidemiological studies relating the association between air pollution and SARS-CoV-2. Major findings are consistent, highlighting the important contribution of air pollution on the COVID-19 spread and with a less extent also PM₁₀.

Lead-acid batteries utilised in electrical substations release hydrogen and oxygen when these are charged. These gases could be dangerous and cause a risk of fire if they are not properly ventilated. Therefore, this research seeks to design and implement a network control panel for heating, ventilation, and air-conditioning systems (HVACS). This is done using a specific range of controllers, which have more than thirty loops of proportional, integral and derivative (PID) control to achieve a cost-effective design. It performs the required function of extracting hydrogen, oxygen, and maintaining the desired temperature of the battery storage room within the recommended limits (i.e. 25°C ±1°C tolerance) without compromising quality as set out in the user requirement specification in Appendix-A. The system control panel allows the user to access control parameters such as changing temperature set-points, fan-speed, sensor database amongst others. The hardware is configured to detect extreme hydrogen and oxygen gas content in the battery room and ensure that the HVACS extract the gas content to the outside environment. The results of the system show that the network control panel effectively operates as per the recommended system requirements. Therefore, the effective operation of the HVACS ensures sufficient gas ventilation, thus mitigating the risk of fire in a typical battery storage room. Furthermore, the effective operation of HVACS enhances battery lifespan because of regulated operating temperature, which is conducive to minimise the effect of sulfation in lead acid Batteries (LABs).

Recently, we have witnessed a booming development of composites and multi-dopant metal oxides to be employed as novel photocatalysts. Yet the practical application of photocatalysis for environmental purposes is still elusive. Concerns about the unknown fate and toxicity of nanoparticles, unsatisfactory performance in real conditions, mass transfer limitations and durability issues have so far discouraged investments in full-scale applications of photocatalysis. Herein, we provide a critical overview of the main challenges that are limiting large-scale application of photocatalysis in air and water/wastewater purification. We then discuss the main approaches reported in the literature to tackle these shortcomings, such as the design of photocatalytic reactors that retain the photocatalyst, the study of degradation of micropollutants in different water matrices, and the development of gas-phase reactors with optimized contact time and irradiation. Furthermore, we provide a critical analysis of research-practice gaps such as treatment of real water and air samples, degradation of pollutants with actual environmental concentrations, photocatalyst deactivation, and cost and environmental life-cycle assessment.

The ongoing COVID-19 global pandemic is affecting every facet of human lives (e.g., public health, education, economy, transportation, and the environment). This novel pandemic and citywide implemented lockdown measures are affecting virus transmission, people’s travel patterns, and air quality. Many studies have been conducted to predict the COVID-19 diffusion, assess the impacts of the pandemic on human mobility and air quality, and assess the impacts of lockdown measures on viral spread with a range of Machine Learning (ML) techniques. This review study aims to analyze results from past research to understand the interactions among the COVID-19 pandemic, lockdown measures, human mobility, and air quality. The critical review of prior studies indicates that urban form, people's socioeconomic and physical conditions, social cohesion, and social distancing measures significantly affect human mobility and COVID-19 transmission. During the COVID-19 pandemic, many people are inclined to use private transportation for necessary travel purposes to mitigate coronavirus-related health problems. This review study also noticed that COVID-19 related lockdown measures significantly improve air quality by reducing the concentration of air pollutants, which in turn improves the COVID-19 situation by reducing respiratory-related sickness and deaths of the people. It is argued that ML is a powerful, effective, and robust analytic paradigm to handle complex and wicked problems such as a global pandemic. This study also discusses policy implications, which will be helpful for policymakers to take prompt actions to moderate the severity of the pandemic and improve urban environments by adopting data-driven analytic methods.

Sea anemones are a remarkable source of active principles due to a decentralized venom system. Blood vessel formation or angiogenesis is a very promising target against cancer, but the few available anti-angiogenic compounds have a limited efficacy. In this study, a protein fraction was purified from tentacles of Anemonia viridis able to limit endothelial cells proliferation and vessel network formation or angiogenesis at low concentration (14 nM). The sequences in this protein fraction were determined with Edman degradation and Mass Spectrometry In Source Decay and revealed homologies with BDS sea anemones. The presence of a two turn alpha helix observed with Circular Dichroism and a trypsin activity inhibition suggested that the active principle could be a Kunitz-type inhibitor, which may interact with an integrin due to a RGD motif well exposed to the solvent as revealed by Molecular Modeling. This active principle could improve antiangiogenic therapy from existing antiangiogenic compounds binding on the VEGF.

Along with density and mass variations of the oceans driven by global warming, Glacial Isostatic Adjustment (GIA) in response to the last deglaciation still contributes significantly to present-day sea-level change. Indeed, in order to reveal the impacts of climate change, long term observations at tide gauges and recent absolute altimetry data need to be decontaminated from the effects of GIA. This is now realized by means of global models constrained by the observed evolution of the paleo-shorelines since the Last Glacial Maximum, which account for the complex interactions between the solid Earth, the cryosphere and the oceans. In the recent literature, past and present-day effects of GIA are often expressed in terms of fingerprints describing the spatial variations of several geodetic quantities like crustal deformation, the harmonic components of the Earth's gravity field, relative and absolute sea level. However, since it is driven by the sluggish readjustment occurring within the viscous mantle, GIA shall taint the pattern of sea-level variability also during the forthcoming centuries. The shapes of the GIA fingerprints reflect inextricable deformational, gravitational, and rotational interactions occurring within the Earth system. Using up-to-date numerical modeling tools, our purpose is to revisit and to explore some of the physical and geometrical features of the fingerprints, their symmetries and intercorrelations, also illustrating how they stem from the fundamental equation that governs GIA, i.e., the Sea Level Equation.