The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

The photodegradation of azithromycin present was carried out in water using H2O2 under UV irradiation. The reaction variables considered in this study were the amount of H2O2 solution and the initial concentration of azithromycin to evaluate the performance of the photodegradation process. The azithromycin degradation was not observed in the dark during stirring for 20 minutes. The study showed efficient photodegradation of azithromycin using H2O2 as an oxidant in the presence of UV irradiation. The azithromycin degradation was affected significantly by the pH of the irradiated solution. The degradation was low at an acidic pH and showed an increasing trend as the pH changed to basic. The azithromycin degradation was increased with a higher amount (higher concentration) of H2O2. The degradation of azithromycin decreased with a higher concentration of azithromycin in the reacting solution. The highest degradation of AZT was achieved in 1 hour using a 1.0 ppm AZT solution containing 3 ml of H2O2. The experimental data obtained was well-fitted to zero-order reaction kinetics. The results of this study were found to be superior when compared with those reported in the literature, with photocatalysis using nanomaterials and photolysis using irradiation and H2O2. The UV/H2O2 system was found to be quite efficient for the photodegradation of azithromycin, and this system can be applied to degrade other organic pollutants present in industrial wastewater. To this point, such a study has not been reported specifically for AZT photodegradation.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

Non-impregnated small pore graphite (NSPG) with the compact microstructure for using in molten salt reactors (MSR) was prepared by the novel process, and the pore diameter of the obtained graphite was reduced to ~800 nm. The irradiation evaluation of the prepared graphite was carried out by 7 MeV Xe26+ ion irradiation and the microstructural changes of the graphite were investigated with IG-110 as a comparison. The graphitization degree of NSPG was higher than that of IG-110, though it was not subjected to an impregnation process. Under low-dose ion irradiation (

In this paper, the single event burnout(SEB) and reinforcement structure of 1200V SiC MOSFET (SG-SBD-MOSFET) with split gate and schottky barrier diode(SBD) embedded were studied. The device structure was established using Sentaurus TCAD, and the transient current changes of single event effect(SEE), SEB threshold voltage, as well as the regularity of electricfield peak distribution transfer were studied when heavy ions were incident from different regions of the device. Based on SEE analysis of new structural device, two reinforcement structure designs for SEB resistance were studied, namely the expansion of P+body contact area and the design of multi-layer N-type interval buffer layer. Firstly, two reinforcement schemes for SEB were analyzed separately, and then comprehensive design and analysis were carried out. The results showed that the SEB threshold voltage of heavy ions incident from the N+source region was increased by 16% when using the P+body contact area extension alone; When the device is reinforced with multi-layer N-type interval buffer layer alone, the SEB threshold voltage increases by 29%; The comprehensive use of P+body contact area expansion and multi-layer N-type interval buffer layer reinforcement increased the SEB threshold voltage by 33%. Overall, the breakdown voltage of the reinforced device decreased from 1632.935V to 1403.135V, which can be seen as reducing the remaining redundant voltage to 19%. The device performance was not significantly affected.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

In our study we investigated the accelerated aging process of PLA under 253.7 nm UV-C irradiation with the use of GPC, NMR, FTIR, DSC methods and formal kinetic analysis. The results of GPC and DSC indicated a significant degree of destructive changes in PLA macromol-ecules, while spectroscopic methods NMR and FTIR showed maintenance of PLA main structural elements even after a long time of UV exposure. In addition to that, the GPC method displayed the formation of a high-molecular fraction starting from 24 hours of irradiation, and an increase in its content after 144 hours of experiment. It has been showed for the first time that a distinctive feature of prolonged UV exposure is the occurrence of intra- and intermolecular radical recom-bination reactions, leading to the formation of a high-molecular fraction of PLA decomposition products. This causes the observed slowdown of the photolysis process. It was concluded that photolysis of PLA is a complex of physicochemical processes, the mechanism of which depends on morphological changes in a solid phase of the polymer under UV radiation.

The manuscript presents the optical properties of directly deposited films of gold nanoparticles (AuNPs) prepared by ultrasonic spray pyrolysis technology. Four samples were produced, with an AuNPs deposition time of 15 min, 30 min, 1h and 4h on the glass substrate. The morphological characterization of the deposited films showed that the size of the first deposited AuNPs is between 10 and 20 nm, while with a longer duration of the deposition process, larger clusters of AuNPs grow by coalescence and aggregation. The prepared layers were optically characterised with Ultraviolet–visible spectroscopy (UV-vis) and ellipsometry. The ellipsometric measurements showed an increasingly denser and thicker effective thickness of the AuNPs layers. The extinction spectra display a clear local surface plasmonic resonance (LSPR) signature (peak 520-540 nm), indicating the presence of isolated particles in all samples. For all AuNPs layers, the imaginary part of both ε// and ε⏊ is dominated by a central peak around 2.2 eV corresponding to the LSPR of isolated particles and a high-energy shoulder due to Au interband transitions. It is shown that, as the density of particles increases, the extinction cross section grows over the whole spectral range where measurements are taken. Thus response can be explained with an enhanced electromagnetic response among AuNPs, that can be connected to the increase of particle density but also by the formation of clusters and irregular structures.

Gold nanoparticles (AuNPs) exhibit improved optical and spectral properties compared to bulk materials, making them suitable for detection of DNA, RNA, antigens, and antibodies. Here, we describe a simple, selective, and rapid non-cross linking detection assay, using approx. 35 nm spherical Au nanoprobes, for a common mutation occurring in exon 19 of the epidermal growth factor receptor (EGFR), associated with non-small cell lung cancer cells. AuNPs were synthesized based on the seed-mediated growth method and functionalized with a specific 16 bp thiolated oligonucleotide using a pH-assisted method. Both AuNPs and Au nanoprobes proved to be highly stable and monodisperse by ultraviolet-visible spectrophotometry, dynamic light scattering (DLS) and electrophoretic light scattering (ELS). Our results indicate a detection limit of 1.5 µg mL−1 using a 0.15 nmol dm−3 Au nanoprobe concentration. In conclusion, this work is an effective possibility for a straight-forward, fast, and inexpensive alternative for the detection of DNA sequences related to lung cancer, leading to a potential platform for an early diagnosis of lung cancer patients.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

The degradation of the persistent compound perfluorooctanoic acid (PFOA) in water by ultraviolet light in the presence and absence of hydrogen peroxide was examined. A laboratory experiment was designed to answer the question: is UV spectrophotometry feasible for PFOA research? Spectrophotometry was able to measure the degradation of PFOA, but a very high concentration was required. The 1 mg/L used is very concentrated when compared to the 70 ng/L suggested level in drinking water. A UV/Visible diode array scanning spectrophotometer was used to measure changes in PFOA concentrations after 15-minute exposures to ultraviolet light and ultraviolet light with hydrogen peroxide. A noticeable drop in concentration was measured for a 1 mg/L sample. The reaction kinetics were calculated and are likely skewed due to the greater concentration of experimental PFOA. These preliminary results will allow for the next phases of PFOA research to commence, including confirmation through liquid chromatography/mass spectrometry of low concentrations and developing bioremediation techniques.

The role of postmastectomy radiotherapy and regional nodal irradiation after radical mastectomy is defined in high-risk patients with locally advanced tumors, positive margins, and unfavorable biology. The benefit of postmastectomy radiotherapy in intermediate-risk patients (T3N0 tumors) remains a matter of controversy. It has been demonstrated that radiotherapy after breast-conserving surgery lowers the locoregional recurrence rate compared with surgery alone and improves the overall survival rate. In patients with 4 or more positive lymph nodes or extracapsular extension regional lymph node irradiation is indicated regardless of the surgery type (breast-conserving surgery or mastectomy). Despite the consensus that patients with more than 3 positive lymph nodes should be treated with radiotherapy, there is a controversy regarding the recommendations for patients with one to three involved lymph nodes. In patients with N0 disease with negative findings on axillary surgery, there is a trend to administer regional lymph node irradiation in patients with a high risk of recurrence. In patients treated with neoadjuvant systemic therapy and mastectomy, adjuvant radiotherapy should be administered in case of clinical stage III and/or ≥ypN1. In patients treated with neoadjuvant systemic therapy and breast-conserving surgery, postoperative radiotherapy is indicated irrespective of pathological response.

The swelling behavior of titanium-modified austenitic stainless steel 15-15Ti was investigated by pre-implantation of He at room temperature followed by Ni irradiation at 580 °C to peak doses of 120, 240 and 400 dpa. Relatively smaller cavities were observed in the zone of helium implantation while large cavities appeared in the region near the damage peak. A correction formula of the dpa curve was proposed and applied for samples with large swelling. It is found that the steady-state swelling rate of 15-15Ti keeps at ~1% /dpa even to high doses. By comparing the swelling data of the helium-implanted and helium-free regions at same doses, 70 dpa and 122 dpa, the suppression of excessive helium on swelling can be deduced at such doses.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

The roots, leaves, and other parts of American ginseng contain ginsenosides and polyphenols, among other bioactive components. So far, reports on exploring the changes in bioactive components within its leaves after heat treatment have been limited. In the present study, we investigated the effects of far-infrared irradiation (FIR) heat treatment from 160 to 200 ℃ on the deglycosylation and dehydration rates of the bioactive components in American ginseng leaves. As the temperature was increased, the amounts of constant ginsenosides decreased while those of rare ginsenosides increased. After FIR heat treatment of the American ginseng leaves at an optimal 190 ℃, the highest total polyphenolic content and kaempferol content were detected, the antioxidant activity was significantly enhanced, and the amounts of rare ginsenosides F4, Rg6, Rh4, Rk3, Rk1, Rg3, and Rg5 were 41, 5, 37, 64, 222, 17, and 266 times higher than those in the untreated leaves, respectively. Moreover, the radical scavenging rates for 2,2-diphenyl-1-picrylhydrazyl and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid), and the reducing power of the treated leaf extract, were 2.17, 1.86, and 1.77 times higher, respectively. Hence, optimal FIR heat treatment at 190 ℃ is an efficient method for producing beneficial bioactive components from American ginseng leaves.

As the global semiconductor market is growing steadily, the need for optimization of the man-ufacturing process is paramount. For example, in the process of transferring the semiconductor chips to the substrate, each chip needs to be individually separated from the dicing tape via a plunger. In this process, however, the fixed chip is not easily removed from the tape due to strong adhesion, and the chip can become damaged if it is forcibly pulled out. Therefore, the present paper reports the development of functional adhesive tapes that initially adhere strongly to the semi-conductor chip on the dicing tape but can be easily removed after transfer. The fabricated functional tape has an initial adhesion of 350 gf, which enables firm fixing of the semiconductor chip to be transferred, and a final adhesion of 0.8 gf after UV curing, thereby facilitating removal of the chip without damage after transfer. Therefore, the fabricated functional tape is expected to contribute to the optimization of the semiconductor manufacturing process and is expected to be useful in the semiconductor package manufacturing process.

Highly transparent, conductive nanosheets are extremely attractive for advanced optoelectronic applications. Previously, we have demonstrated that transparent, conductive Au nanosheets can be prepared by UV irradiation of Au nanoparticle (AuNP) monolayers spread on water, which serves as the subphase. In this study, we show that this UV irradiation technique can easily be extended as a nanosheet modification method by using subphases containing metal ions. That is, aqueous solutions containing Au and Ag ions are effective in modifying Au nanosheets. HAuCl4 solutions increased Au nanosheet thickness, which improved conductivity, but reduced transparency. On the other hand, use of aqueous AgNO3 and CH3COOAg solutions yielded Au-Ag hybrid nanosheets; however, their morphologies depended on the electrolytes used. Homogeneous Au-Ag nanosheets from AgNO3 and AuNPs covered with an Ag nanosheet from CH3COOAg were also produced. Further, these Au-Ag hybrid nanosheets had high conductivity without reduced transparency. Therefore, this UV irradiation method, modified by adding metal ions is quite effective at improving and diversifying properties of Au nanosheets.

Sunscreens are topical preparations containing one or more compounds that protect humans from ultraviolet (UV) light. This review focuses on analytical methods, particularly liquid chromatography, aimed at identifying and determining UV filters (UVFs) in environmental and marine biota matrices. A literature review was done using NIH (PubMed and Medline), FDA and EPA databases, Google Scholar, and Federal Regulations. This retrospective literature review is focused on the last five years. UVFs quantification in environmental and biological matrices showed a wide array of methods where liquid chromatography is predominant. The scientific literature identified a large variety of analytical methodologies that are compared in this review, to evaluate the better results in terms of limits of quantification and the possibility to identify as many analytes as possible simultaneously.

Bixa orellana dye was extracted from the seed by method of Soxhlet extraction using ethanol and a percentage yield of 4.3 was obtained. Recrystallisation of the dye was performed using chloroform and ethanol. TLC was used to separate the dye into Bixin and Norbixin with R_f values of 0.56 and 0.42 respectively. The extracted dye was pH sensitive, insoluble in water but soluble in some organic solvents like ethanol and acetic acid . Characterisation by UV-spectroscopy showed maximum absorption for Bixin and Norbixin at 457nm and 453nm respectively. FTIR spectrum of Bixin and Norbixin showed bands confirming similar functional groups for both Bixin and Norbixin except for –CO- stretching and methylene vibration which was absent in Norbixin.

Modification the biodegradable matrix was carried by graft-copolymerization polylactide with methacrylic acid of various concentrations. Ultraviolet irradiation with different exposure times to the samples was chosen as the initiator of copolymerization. In the experiment the effect of ultraviolet light on polylactide and graft copolymerization was investigated: the resulting samples were studied by viscosimetry, gravimetry, FTIR, static cation- exchange capacity analysis . The conditions for obtaining grafted copolymers and the dependence of the characteristics on the reaction conditions are established.

In the literature, the chemical composition of Rhododendron tomentosum is mainly represented by the study of isoprenoid compounds of essential oil. In contrast, the study of the content of flavonoids will contribute to the expansion of the pharmacological action and the use of the medicinal plant for medical purposes. The paper deals with the technology of extracts from Rhododendron tomentosum shoots using ethanol of various concentrations and purified water as an extractant. Extracts from Rhododendron tomentosum were obtained by a modified method that combined the effects of ultrasound and temperature to maximize the extraction of biologically active substances from the raw material. By the method of high-performance thin-layer chromatography in the system of solvents ethyl acetate: formic acid: water (15:1:1) the following substances have been separated and identified: rutin, hyperoside, quercetin, and chlorogenic acid in all the extracts obtained. To quantify the total flavonoids content, a method of spectrophotometric determination based on the reaction of complexation with aluminum chloride has been developed. It has been proved that the course of the complexation reaction and, accordingly, the quantification of the flavonoid structure substances by the spectrophotometric method is influenced by some factors, including the environment, pH, the structure of the complexes, etc. Regardless of the chosen method, for the further production of Rhododendron tomentosum extracts with a higher content of flavonoid structure substance, it is advisable to use 60%, 70%, and 80% ethyl alcohol as extractant.

Nondestructive determination of the neutron irradiation induced embrittlement of nuclear reactor pressure vessel steel is a very important and recent problem. In the frame of the so called NOMAD project, funded by the Euratom research and training program, novel nondestructive electromagnetic testing methods were applied for inspection of irradiated reactor pressure vessel steel. In this review the most important results of this project are summarized. Different methods were used and compared with each other. Measurement results were compared with the destructively determined ductile to brittle transition temperature (DBTT) values. Three magnetic methods: 3MA (micromagnetic, multiparameter, microstructure and stress analysis), MAT (magnetic adaptive testing) and Barkhausen noise technique (MBN) were found as the most promising techniques. The results of these methods were in good confidence with each other. Good correlation was found between the magnetic parameters and the DBTT values. The basic idea of the NOMAD project is to use a multi-method/multi-parameter approach and to focus on their synergies that allows to recognise the side effects therefore supressing them at the same time. Different types of Machine Learning (ML) algorithms were tested in competition and their performances were evaluated. The important outcome of the ML technique is that not only one, but several different ML techniques could reach required precision and reliability, i.e. to keep the DBTT prediction error lower than +/-25°C threshold, which was previously not possible for any of the NDE methods as single entities. A calibration/training procedure was carried out on the merged outcome of testing methods with excellent results to predict transition temperature, yield strength and mechanical hardness for all investigated materials. Our results, achieved within NOMAD project can be useful for the future potential introduction of this (and in general, any) nondestructive evolution method.

Breast Angiosarcoma is a rare malignancy, accounting less than 1% of all soft tissue. It comprises primitive and secondary subtypes, such as radiogenic breast angiosarcoma (RAS). Despite the multimodal treatment, angiosarcomas represent an incurable disease for many patients and represent a cause of substantial deterioration of their quality of life. Surgery represents the cornerstone in the management, but high recurrence rates are reported. Electrochemotherapy (ECT) is practicable locoregional treatment in patients with advanced angiosarcoma, in a multimodal therapeutic strategy. ECT palliative benefit includes optimal patient compliance, good local hemostasis control, and local responses. Considering that only 22 cases are described in literature, we reported a rare case of RAS treated with ECT, after a multidisciplinary approach including Next Generation Sequencing (NGS). A literature review about the feasibility of ECT in RAS management was also performed.

Background: SARS-CoV-2 continues to impact human health globally, with airborne transmission being a significant mode for transmission. In addition to tools like vaccination and testing, counter-measures that reduce viral spread in indoor settings are critical. This study aims to assess the efficacy of UV-C light, utilizing the Violett sterilization device, as a countermeasure against airborne transmission of SARS-CoV-2 in the highly susceptible Golden Syrian hamster model. Methods: Two cohorts of naïve hamsters were subjected to airborne transmission from experimentally infected hamsters; one cohort was exposed to air treated with UV-C sterilization, while the other cohort was exposed to un-treated air. Results: Treatment of air with UV-C light prevented the airborne transmission of SARS-CoV-2 from experimentally exposed hamster to naïve hamsters. Notably, this protection was sustained over a muti-day exposure period during peak viral shedding from hamsters. Conclusion: These findings demonstrate the efficacy of the UV-C light to mitigate airborne SARS-CoV-2 transmission. As variants continue to emerge, UV-C light holds promise as a tool to reduce infections in diverse indoor settings, ranging from healthcare facilities to households. This study reinforces the urgency of implementing innovative methods to reduce airborne disease transmission and safeguard public health against emerging biological threats.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

Chert rock is a by-product of sand quarrying (about 40% in the geological section). All attempts to use ordinary technologies for aggregate production from chert have been economically unsuccessful, resulting in significant chert "waste" accumulation covering vast quarry areas. This paper presents the study results of the effect of microwave irradiation on the mechanical properties of chert gravel, which is mineralogically relatively homogenous and consists of fine quartz grains. The results show that an increase in irradiation time decreases the strength of chert gravel (by a factor of 4-6 for the 2.5 min of irradiation), while the quenching changes the fractional content of the samples after the crushing test, decreasing the Gravel-to-Sand ratio.

Ionizing radiation exposure is known to induce molecular and cellular injury, inflicting a cascade of potentially catastrophic events leading to tissue and organ damage. Metabolomic analysis allows for the identification and quantification of small molecules downstream of genomic changes induced by radiation exposure. We aimed to characterize metabolomic changes that underscore the prefinal stage of lethally irradiated rhesus nonhuman primates (NHPs). Peripheral blood was drawn at baseline, post-exposure as well as at the preterminal stage of NHPs (immediately prior to death in moribund NHPs), which did not survive exposure with 7.2 Gy total-body radiation (LD70/60). Herein, we analyzed global metabolomic changes using ultra-performance liquid chromatography (UPLC) quadrupole time-of-flight mass spectrometry (QTOF-MS) in plasma samples of NHPs collected at various timepoints in relation to irradiation. The overall goal was to identify metabolic shifts present immediately prior to death. Our findings, for the first time, show that radiation induced significant time dependent metabolic perturbations when compared to pre-irradiation samples, particularly in the glycerophospholipid metabolism and steroid hormone biosynthesis and metabolism pathways. These findings provide valuable insights for identifying biomarkers for lethality, which may be helpful for triage during a mass casualty scenario.

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

Development of new techniques of multimodal treatment, diagnostics of various neoplasms and improvement of these techniques can significantly increase the life expectancy of patients with carcinomas of the colon and abdominal cavity organs, since prevention of various side effects of radiation therapy is one of the main problems of oncological care. Electron irradiation is one of the most promising types of radiation therapy. There are no data on proliferation and apoptosis of the colon epithelium after irradiation with electrons, especially in different modes (single and summary). Aim of the study: Morphological evaluation of apoptosis and proliferation of colonic epithelium after local irradiation with electrons at doses 2 Gy and 25 Gy. Materials and methods. Colon fragments from sexually mature Wistar rats (n=50, body weight 200 ± 10 g) were divided into three groups: I - control (n = 10); II - experimental group (n = 20; local single electron irradiation at a dose of 2 Gy), III - experimental group (n=30), local fractional irradiation with electrons at a total dose of 25 Gy. They were studied by light microscopy using hematoxylin and eosin staining and immunohistochemical reactions with antibodies to Ki-67 and Cas3. Morphological disorders were accompanied by increased expression of pro-apoptotic molecules (caspase-3), and the period of regeneration by proliferative marker (Ki-67). Conclusions: Local fractional irradiation of the colon with electrons at a dose of 2 Gy and 25 Gy resulted in minor changes in the epithelium, a decrease in the number of goblet cells, but with preservation of regenerative potential, mild degenerative-dystrophic lesions. Intestinal crypts were damaged, leading to a decrease in Ki-67 and an increase in the number of caspase-3-positive epitheliocytes.

This study aimed to assess the impact of different modes of laser irradiation on the bactericidal efficacy of aPDT. Dentin plates were prepared by sectioning the crown dentin of bovine teeth infected with Streptococcus sobrinus. Nine aPDTs involving the combinations of three photosensitizers (brilliant blue, BB; acid red, AR; and methylene blue, MB) and three laser irradiation modes (50 mW for 120 s, 100 mW for 60 s, and 200 mW for 30 s) were performed for each infected dentin plate, and the control group consisted of the specimens not applied with aPDT. The bactericidal effects in 10 experimental groups were evaluated (n=11) using both assays of the colony-count and adenosine triphosphate (ATP). The data obtained were analyzed using the Kruskal-Wallis test. The aPDT performed with semiconductor laser in combination with BB, AR, and MB exerted a remarkable bactericidal effect. aPDT with MB exerted a more significant bactericidal effect in the colony-count assay. The results of aPDT performed with varying irradiation times and powers but with constant irradiation energy showed no difference with AR and MB between the modes, whereas BB showed a more significant bactericidal effect when irradiated for a shorter time at a higher irradiation power.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

Target detection of defense technology is being rapidly upgraded with modern surveillance technologies. The latest techniques of surveillance are already being implemented for defense applications. Self-protection and hiding from opposing forces are the key principle for protection of special team in defense. Camouflage textiles aims to create confusing objects for target detection of military personnel. These textiles are applied for military protection such as clothing, weapon, vehicle and location hiding nets/tents, etc. The urgent need of camouflage textiles have been formulated with a technical solution and implementation of right camouflage materials for concealment of defense target signature against dry leaves, green leaves, tree bark-woodland combat background; water-marine combat background; sand-desertland combat background; stone-stoneland combat background; snow-snowland combat background; sky combat background and ice-iceland combat background, concrete-concreteland combat background (DGTWSICB) in ultraviolet-visible-infrared (UV-Vis-IR) spectrums. This hypothesis of optical & surveillance engineering has been coalesced for advancement of UV-Vis-IR-DGTWSICB camouflage textiles technology. The principle of camouflage engineering has been approached by broader spectrum probe in UV-Vis-IR rather than Vis ranges only. Furthermore, single formulation of camouflage textiles has been proposed for multidimensional CBs-DGTWSICB. Electromagnetic spectrum, reflection, electron energy, photonic signal and imaging mechanism in UV-Vis-IR have been presented for optical engineering of concealment, detection, recognition and identification of target signature against DGTWSICB. Spectrum relationship of camouflage materials and DGTWSICB materials have been illustrated and compared in UV-Vis-IR spectrums. Camouflage material design, method design & spectral design; adaptive camouflage; techniques for camouflage textile assessment for digital camera and hyperspectral camera imaging; image processing techniques and a hierarchical model have been demonstrated for augmentation of camouflage textiles in UV-Vis-IR illumination. Therefore, anticipated design of camouflage textiles may enhance high-performance innovation for modern surveillance of military protection related to digital camera, hyperspectral camera and radar. This hypothesis includes advance guideline for camouflage textiles design for CBs-DGTWSICB.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

Seaweeds have been the target of much attention due to the known bioactivities of some of their compounds. Although many studies about the application of seaweeds in various areas are available, these data are mostly about the raw extracts and not about specific compounds, such as seaweeds pigments. Moreover, the fungal infections of the skin, nails and hair caused by dermatophytes, are the most common fungal infections in humans. These pathologies require long periods of topical and/or systemic treatment that are associated with adverse effects and contraindications. This study had two objectives, the first was to evaluate the possibility of isolating and characterizing the pigments of Calliblepharis jubata and Fucus vesiculosus; the second was to assess their antifungal activity. The extraction of pigments was performed using a method of extraction by exhaustion; the purification was carried out by column chromatography. Three techniques were used to characterize the pigments, thin layer chromatography (TLC), UV-visible spectrophotometry and Fourier-transform infrared spectroscopy (FTIR). The antifungal activity was evaluated using the micro-dilution method, following the EUCAST international standards, on three dermatophytes, Trichophyton rubrum, Trichophyton mentagrophytes and Microsporum canis. It was possible to observe that the extract obtained from the seaweed C. jubata and F. vesiculosus, corresponding to the purified pigment phycobiliprotein, and the crude extract, an enriched extract, obtained from the seaweed C. jubata showed antifungal activity against the three fungal agents of human skin infection.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

Background: to assess the benefit of a deep inspiration breath hold (DIBH) over standard irradiation technique, and eventually to identify anatomical and/or treatment preplanning characteristics correlated with LAD dose. Methods: We retrospectively identified patients with left-sided breast cancer who underwent whole breast radiotherapy in DIBH. All patients had both plans in DIBH and free-breathing (FB). Receiving operating characteristics (ROC analysis) were performed to define the cut-off point of parameters to predict LAD maximum dose >10 Gy and LAD mean dose > 4 Gy. Areas under the curve (AUCs) were calculated for all variables. Post-test probability has been calculated to evaluate advantage for parameters combination. Results: One hundred ninety-seven patients were identified. LAD dose was significantly reduced in DIBH plans with maximum and mean dose reduced by 31.7% (mean value 3.5 Gy vs 4.8 Gy, p=<0.001) and 28.1% (mean value 8.2 Gy vs 12.8 Gy, p=<0.001) in DIBH plans compared to FB plans. The strongest predictor of LAD maximum dose > 10 Gy and a LAD mean dose > 4 Gy was the minimum distance of LAD from tangent open fields. Other parameters were lung volume and heart volume for LAD Dmax > 10 Gy and lung volume, heart volume and breast separation for LAD Dmean > 4 Gy. Conclusion: The dosimetric benefit of DIBH is valid for all patients and DIBH should be preferred for all left sided patients.

Discovery and development of effective strategies to treat emerging and often drug resistant strains of viral and microbial pathogens presents one of the greatest challenges of the 21st century. Despite nearly a century of progress in developments in antimicrobial and antiviral therapies, infectious diseases still account for a substantial proportion of deaths worldwide, including over 100 million globally in the recent pandemic to date. In recent decades, the plague of antimicrobial resistance also represents an additional and alarming signal for both human and animal healthcare and signals a renewed sense of urgency in addressing this issue. This has made the search for novel classes of antibiotics, antivirals and therapeutics found to be capable of bypassing the microbial and viral resistance mechanisms necessary to in order to replenish our current arsenal of antimicrobial and antiviral drugs and update our therapeutic regimens. In addition, the tremendous impact exerted by viral infections and related pathologies on our lives during the recent decade has forced scientists to acknowledge the opportunities and challenges associated with tackling infectious diseases by developing effective antiviral agents endowed with novel mechanisms of action. The discovery of new antimicrobial/antiviral agents, as well as the repurposing of existing drugs and therapeutic options will be crucial to fight the ever-increasing resistance of “superbugs”, pathogenic fungi, viruses, and parasites. Proponents of modern biophoton therapy proposed in this paper can trace its origins to the Russian scientist Alexander Gurwitsch, who a century ago observed ultra-weak emissions of light emerging from an onion root and soon found additional living tissues to be emanating similar energetic phenomena, thus energizing research which continues to the present day and projected toward the development of useful applications of the new-found biological photonic phenomena. The purpose of the present paper is to introduce the past experiences, potential applications and highly successful outcomes of biophotonic therapy as an option to treat infectious diseases including HIV, Hepatitis C, MRSA, and others, with emphasis on efficacy of using biophotonic therapies to treat and ameliorate the drug resistant variants of the above infectious agents, including potential applications for the current COVID-19 pandemic and in preparation for the emergence of the next epidemic or pandemic.

The use of covers to protect blueberry orchards from adverse weather events has increased due to the variability in climate patterns, but the effects of rain cover and netting materials on yield and fruit quality have not been studied yet. This research evaluated the simultaneous effect of LDPE plastic cover, woven cover and netting materials on environmental components (UV light, PAR, NIR and growing degree days, GDD), plant performance (light interception, leaf area index, LAI, yield and flower development), and fruit quality traits (firmness, total soluble solids and acidity) in two blueberry cultivars. On average, UV transmission under netting was 11% and 43% higher compared to that under woven and LDPE plastic covers, while NIR was 8 -13% higher with both types of rain covers, with an increase in fruit air temperature and GDD. Yield was 27% higher under woven cover with respect to netting, but fruit firmness values under netting were 12% higher than those of LDPE plastic cover. Light interception, LAI and flower development explained 64% (p=0.0052) of the yield variation due to the cover material effect. The obtained results suggest that the type of cover differentially affects yield and fruit quality in blueberries due to the specific light and temperature conditions generated under these materials.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

Cross-contamination poses a pervasive challenge within the realm of food production. The propagation of infections is recognized to occur in an uncontrolled manner. Given the essential nature of food for human sustenance, the domain necessitates stringent control over contamination and cross-contamination due to the perilous potential for severe intoxication. In the context of managing biological contamination in fresh food items, commencing from production and extending to the final consumable, the utilization of chemicals must be judiciously limited to avert adverse effects. This biochemical approach, however, engenders environmental and health quandaries attributable to the incessant employment and discharge of such materials. The present research is centered upon demonstrating, at a laboratory scale, a process involving the leaching of plants, accompanied by the application of UVC irradiation during this procedure. This obviates the necessity for chemical solutions. The empirical findings showcased that subjecting the solution utilized for vegetable washing to UV irradiation rendered it 99 % microorganism-free in vegetables and 99.999% in the water component. This attests to efficacious decontamination, resource conservation, and mitigation of discharge-associated predicaments. The mathematical model precisely characterizes the behaviors manifested in the empirical data, thereby establishing a close correspondence with the kinetics law equation. Grasping the fundamental mechanisms and articulating them enables the enhancement of optimization and seamless integration of this approach to combat cross-contamination with heightened efficacy. This approach to addressing cross-contamination holds significant promise, underscoring its pivotal role in elevating food safety measures and ameliorating environmental repercussions. Envisioning the implementation of these practices at an industrial scale carries the potential to yield substantial dividends in terms of public health and sustainable practices

Plastic materials have revolutionized modern life, particularly in the domain of food packaging, owing to their versatility, lightweight nature, and ease of processing. However, the environmental ramifications of non-degradable plastics have raised concerns. Polylactic acid (PLA), derived from renewable sources, presents a sustainable alternative due to its biodegradability and exceptional barrier, mechanical, and safety properties. Nevertheless, the high UV transmittance of PLA limits its use for photosensitive food and pharmaceutical packaging, where UV radiation can lead to nutritional loss and spoilage. Various methods have been explored to enhance the UV-blocking capabilities of PLA, including the integration of inorganic nanoparticles and surface coatings. Despite advancements, these approaches often compromise the inherent transparency of PLA. Incorporating large conjugated groups can maintain transparency but introduces additional challenges. This paper reviews modification methods to enhance PLA's UV-barrier properties and anticipates its expanded utility in food and drug packaging, promoting UV resistance and diversifying PLA's applications.

CuO/ZnO/Al2O3 catalyst is a commonly used catalyst for rea methanol steam reforming reaction. Oxalic acid was as precipitant in preparing oxalate precursor of CuO/ZnO/Al2O3 catalyst by co-precipitation, deionized water and ethanol were as solvents, microwave irradiation and water bath were as aging heating manner respectively. It indicated that ethanol selected crystal phase composition of oxalate precursors and restricted their growth. Microwave irradiation prompted the isomorphous substitution between Cu2+ of CuC2O4 and Zn2+ of ZnC2O4 in mother liquid, forming the master phase (Cu,Zn)C2O4 in precursor, the solid solution Cu-O-Zn formed after calcination, which exhibited nano-fibriform morphology. It possessed small CuO grains, large surface area and strong synergy between CuO and ZnO, which is beneficial to improve the catalytic performance of methanol steam reforming, the STY of H2 reached 516.7 mL·g-1·h-1, and the selectivity of CO was only 0.29%.

Background: Radiotherapy is an important part of the medical therapy concept treating tumors in the head and neck region; however, the impact on the field of dentistry could be im-mense. The objective of this study was to evaluate the microtensile bond strength (µTBS) of uni-versal adhesives and to compare the results of different application modes (etch-and-rinse and self-etch) on irradiated and sound human dentin. Methods: Dentin specimen of 180 extracted human wisdom teeth were divided in two superordinate groups. Ninety teeth received either no irradiation (control group) or the high-level therapeutic dose of 60 Gy (test group) applied frac-tionally (2 Gy/day, 5 days/week, 6 weeks). Samples from each group were randomly divided in-to six subgroups assigned to three established universal adhesives (Futurabond® U, VOCO; AdheSE® Universal, Ivoclar Vivadent; Xeno® Select, Dentsply) in both conceivable application modes: etch-and-rinse and self-etch (n = 15). Bond strength was assessed with a universal testing machine immediately after application and light curing of the adhesive materials. Statistical analysis was performed using two-way ANOVA (p<0.01) and Tukey's test (p<0.05). Results: The effect of dentin irradiation and application mode for the adhesive restoration was found to be significant (p<0.01, ANOVA). In all groups, a decrease of µTBS could be observed when used on irradiated dentin. However, no significant influence of high level radiation on the bond strength of Futurabond® U and AdheSE® Universal in both modes could be evaluated (p>0.05, Tukey´s test). Solely in the case of the adhesive system Xeno® Select, significantly reduced bond strength could be determined in self-etch mode after irradiation (group 60 Xse) compared to the control group (0 Xse) (p<0.05, Tukey´s test). Conclusions: Within the limitations of an in vitro study, some effects of high-level tumor irradiation on the bond strength of universal adhesives can be detected. However, these effects were strongly depending on the used material and application mode.

Date palm trees generate large amounts of various types of waste, including leaf sheath fibers which can be used as a low-cost, precursor for production of biochar including activated carbon (AC) that can be employed for adsorption of contaminants. In the current study, activated carbon was made from leaf sheath fibers of date palm (LSDPFAC) by use of chemical activation with K2CO3, combined with microwave irradiation, characterized and evaluated for its adsorptive capacity of lead ions (Pb2+). The Brunauer–Emmett–Teller (BET) surface area, Langmuir surface area, total pore volume and average pore diameter of LSDPFAC were 560.20 m2/g, 744.31 m2/g, 0.29 cm3/g and 2.47 nm respectively. When the initial concentrations of Pb2+ were increased from 1 to 10 mg/L, Pb2+ adsorption increased from 0.97 to 8.76 mg/g, dry mass (dm) while the percent of Pb2+ removed decreased from 96.70 to 87.60%. The greatest removal of Pb2+ occurred at pH 13 with adsorption capacity of 9.15 mg/g, dm. Results of isotherm and kinetic studies demonstrated that adsorption of Pb2+ onto LSDPFAC was best described by the Freundlich isotherm and pseudo-second order (PSO) models. Langmuir monolayer adsorption capacity, Qm was 14.10 mg/g. Thermodynamic parameters of H°, S°, G° and Ea were 6.39 kJ/mol, 0.12 kJ/mol.K, -31.28 kJ/mol and 15.90 kJ/mol, respectively, which demonstrated that adsorption of Pb2+ by LSDPFAC was endothermic, spontaneous and governed by physisorption.

Over the past two decades, covalent organic frameworks (COFs) have become the most widely studied porous crystalline materials. Its specific physical and chemical properties are determined by the arrangement of atoms (crystal structure). Therefore, the determination of its structure is arguably the most important characterization step for COFs. Although single crystal X-ray diffraction (SCXRD) is the most widely used method for structure determination, the size of COF crystals is too small, or their crystal quality is so poor that confirmation of their structure is limited to lattice fringes by transmission electron microscopy (TEM). At present, many 2D-COFs have clear PXRD patterns, but not all 2D-COFs can obtain specific lattice fringes. This severely hinders the development of the COF field. Here, we discover the lattice shrinkage behavior of COFs under electron beam irradiation by comparing the lattice fringes of 2D-COFs under different conditions. By comparing the lattice fringes of TAPT-TFPT COF at room temperature and under liquid nitrogen freezing conditions, we found that the lattice fringes are in good agreement with the Powder X-ray diffraction (PXRD) and theoretical values of COF (2.213 nm) under freezing conditions, however, the lattice fringe spacing is only 1.656 nm at room temperature. The discovery not only provides new insights into the TEM characterization of COFs, but also further expands the range of crystalline COF materials.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

The nature of the blue color in the iodine-starch reaction (or, in most cases, iodine-iodide-starch reaction, i.e. as I2 as well as I- are typically present) has for decades elicited debate. The intensity of the color suggests a clear charge-transfer nature of the band at ~600 nm, and there is consensus regarding the fact that the hydrophobic interior of the amylose helix is the location where iodine binds. Three types of possible sources of charge transfer have been proposed: (1) chains of neutral I2 molecules, (2) chains of poly-iodine anions (complicated by the complex speciation of the I2 - I- mixture), or (3) mixtures of I2 molecules and iodide or polyiodide anions. An extended literature review of the topic is provided here. According to the most recent data, the best candidate for the “blue complex” is a I2-I5-I2 unit – expected to occur in repetitive manner inside the amylose helix.

The aim of this study is to compare different methods used for determination of the DS for sulfonated membranes before and after high dose irradiation. Commercial PEEK was homogenously sulfonated up to DS of 60-90% and the membranes were prepared using solvent casting method. Part of the samples were irradiated with 10 MeV electron beam up to 500 kGy dose to assess the ionising radiation induced effects. Both non-irradiated and irradiated membranes were characterized by Fourier Transformation infrared (FT-IR) spectrometry, thermogravimetric analysis (TGA), proton nuclear magnetic resonance (1H-NMR), electrochemical impedance analysis and for the first time for non-irradiated membranes by spectrophotometric analysis with Cr(III). Comparison of the above-mentioned methods for application for DS assessment was done. It was observed that irradiated membranes presented a higher value of DS. Appearance of different new signals in 1H-NMR and FT-IR spectra of irradiated membranes indicated the effects of radiation induced changes in the structure of SPEEK materials. It was determined that the novel method with Cr(III) is applicable for the determination of SPEEK DS under 80%.

A variety of bioactive substances present in fruits and vegetables processed products have health-promoting properties. Consumption of nutrient-rich plant-based products is essential to address undernutrition and micronutrient deficiencies. Preservation is paramount in manufacturing plant-based non-solid foods such as juices, purees, and sauces. Thermal processing has been widely used to preserve fruit and vegetable-based products by reducing enzymatic and microbial activities, thereby ensuring safety and prolonged shelf life. However, the nutritional value of products is compromised due to the deleterious effects of thermal treatments on essential nutrients and bioactive compounds. To prevent the loss of nutrients associated with thermal treatment, alternative technologies are being researched extensively. In studies conducted on non-solid food, UV-C treatment has been proven to preserve quality and minimize nutrient degradation. This review compiles information on the use of UV-C technology in preserving the nutritional attributes of non-solid foods derived from fruit and vegetables. Legislation, market potential, consumer acceptance, and limitations of UV-C are reviewed.

The relaxation processes induced by an exposure of the Ar matrices doped with CH4 (0.1 – 10%) to an electron beam were studied with a focus on the dynamics of radiolysis products – H atoms, H2 molecules, CH radicals, and energy transfer processes. Three channels of energy transfer to dopant and radiolysis products were discussed: by free charge carriers, free excitons and photons from the “intrinsic source” provided by emission of the self-trapped excitons. Radiolysis products along with the total yield of desorbing particles were monitored in a correlated manner. Analysis of methane transformation reactions induced by free excitons showed that the CH radical can be considered as a marker of the CH3 species. The competition between exciton self-trapping and energy transfer to the dopant and radiolysis products has been demonstrated. A nonlinear concentration behavior of the H atoms in doped Ar matrices has been established. Real-time correlated monitoring of optical emissions (H atom and CH3 radicals), particle ejection, and temperature revealed a nonmonotonic behavior of optical yields with a strong luminescence flash after almost an hour of exposure, which correlated with explosive pulse of particle ejection and temperature. The connection of this phenomenon with the processes of energy transfer and radical-radical recombination is discussed.

This study aimed to investigate the atherogenicity (quality) of LDL particles in patients with acute and recovered from COVID-19 infection. The participants were adults, aged 18 years or older of both sexes. Those with positive RT-PCR results at baseline were included in the Acute COVID-19 group (n=33), and those with negative RT-PCR six months after acute infection, were included in the Recovered COVID-19 group (n=30). The LDL quality was evaluated using three validated methods: Z-scan, UV-visible spectroscopy, and Lipoprint. The Recovered COVID-19 group showed significantly higher numbers of large LDL particles (less atherogenic) than the Acute COVID-19 group (P&lt;0.05). We also found that COVID-19 infection was associated with the oxidative modification of LDL particles. D-dimer and CRP levels were correlated with Z-scan results and antioxidant-amount estimate. Moreover, we noticed that the infection left a sequel in LDL quality, even after six months of recovery. These findings highlight the importance of monitoring lipids during and after recovery from COVID-19 infection, and their potential deleterious effect on the LDL profile might correlate with the progression of atherosclerosis and poor clinical outcomes.

In this review, we focus on a small section of the extensive literature that deals with the materials containing pristine defective CNs and those incorporated in the hybrid materials. We will discuss only those topics that focus on structural defects related to the introduction of perturbation into the surface topology of a nanostructure. We focus mainly on the method using microwave (MW) irradiation, which is a powerful tool for synthesizing and modifying carbon-based solid materials. In addition, the simplicity of the technique, economy, and the possibility of conducting the reaction in solvents and solid phase, in the presence of components of different chemical nature, allows use in various combinations. In this review, we will emphasize the advantages of synthesis using MW-assisted heating and indicate the influence of the structure of the obtained materials on their physical and chemical properties. We will also highlight the role of the occurrence of defects in the carbon material and the implication in designing their properties and applications.

The drug delivery systems receive more and more attention for the control and treatment of many diseases due to their increased number in recent years. The main aims of this study were to develop and to characterize a polyurethane drug delivery system that it is intended to be used for the transmembrane transport of nucleosides. Three different samples have been synthesized based on aliphatic diisocyanates (hexamethylene diisocyanate, isophorone diisocyanate and lysine diisocyanate) as organic phase, respectively a mixture of polyethylene glycol, polycaprolactone diol and low molecular weight diols as aqueous phase. The samples were characterized by pH, refractivity index and solubility measurements, drug loading efficacy and release investigations, thermal behavior, Zetasizer, cells viability and irritation tests on mice skin. The results indicate the obtaining of different populations of neutral acido-basic particles with size between 132 and 190 nm; the Zeta potential values and SEM images show a medium tendency to form clusters, while UV-Vis evaluations indicate an almost 70% encapsulation efficacy, a prolonged release (45% of encapsulated substance is released in the first 5 days) and around 70% of particles have penetrated an artificial membrane in the first 24h. The synthesized products can be tested in further clinical trials, the currently tests on cells culture and mice skin revealing no side effects.

A Pt(II) complex featuring chelating tridentate bis-aryloxide tetrahydropyrimidinium based N-heterocyclic carbene (NHC) was synthesized and characterized by using different techniques. The electrochemical properties of the complex were investigated by cyclic voltammetry as well as differential pulse voltammetry, which revealed two reversible one-electron oxidation processes. The chemical generation and isolation of one-electron-oxidized species were performed oxidizing the initial complex by means of AgBF4. The combined UV-Vis/NIR- and EPR-spectroscopy studies supported by density functional theory (DFT) calculations suggest the formation of Pt(II)-phenoxyl radical complex. The latter open-shell derivative was structurally characterized by means of X-ray diffraction analysis. Finally, the neutral platinum complex was tested as a mediator in the process of electrocatalytic oxidation of 2-(methylamino)ethanol (MEA).

The purpose of this investigation was to prepare a water-soluble complex by encapsulation of propolis extract with the carrier 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) and to examine the influence of in vitro simulated gastrointestinal digestion (GID) on the content of the main polyphenolic groups when administered as aqueous suspension. The research was conducted on two continental samples of propolis from Croatia and a mixture of selected polyphenol standards. By applying UAE followed by a lyophilization procedure, it was possible to obtain a powder with a high content of polyphenols. The content of total phenols (TPs), total flavonols/flavones (TFFs) and total flavanones/dihydroflavonols (TFDs) in the fractions of oral and gastric phase and small intestinal phase performed with two models: centrifugation and dialysis through a semi-permeable membrane, was determined by three UV/Vis spectrophotometric methods: Folin-Ciocalteu, aluminium complexation and 2,4-dinitrophenylhydrazine method. The obtained results for both propolis complexes showed stability in the polyphenol content and high bioaccessibility during all three phases of digestion. The bioaccessibility of TPs, TFFs and TFDs under in vitro conditions after dialysis through a semipermeable membrane was lower compared to the intestinal phase model with centrifugation.

A CoCrFeNiNb0.65 eutectic high-entropy alloys (EHEAs) prepared by arc melting were irradiated with a 100 keV He+ ion beam. Swelling, helium bubbles and mechanical response induced by irradiation were evaluated. When the ion fluence reached 1.0×1018 ions/cm2, the irradiation-induced swelling occurred on the sample surface, and as the ion fluence increasing, the swelling became increasingly severe and the surface of Nb-rich phase appeared peeling and shedding. Meanwhile, along the boundaries of matrix and Nb-rich phase there was a neat line of helium bubbles. The size of these helium bubbles decreased with distance from the center of the helium bubble layer. This result indicated that the phase boundaries were favorable sites for the nucleation and gathering of helium bubbles. Nanoindentaion results indicated that hardening and softening induced by He+ ion irradiation occurred in various ion fluences. At ion fluence of 5.0×1017 ions/cm2, the CoCrFeNiNb0.65 EHEAs exhibited an obvious hardening behavior, which can be explained by dislocation-dominated hardening effect. When the ion fluence reached 1.0×1018 ions/cm2 and 2.0×1018 ions/cm2, the hardening effect decreased probably due to the helium bubble aggregation and growth, as well as helium bubbles induced noncompact structures. The results of this study provide insights into the effect of helium bubbles on mechanical evolution and pave the way for designing EHEAs suitable for the nuclear industry.

This review emphasizes the significance of dietary carotenoids in promoting skin health and appearance. The applications of carotenoids in health-promoting and nutrient products and their potential health effects are discussed. Food technology, health, nutrition, dermatology, and dermoaesthetics have recently focused on colorless carotenoids, particularly phytoene, and phytofluene, which have the unique ability to absorb UV radiation. These carotenoids, being significant components of the human diet, are readily bioavailable and have demonstrated various health-promoting actions in re-cent studies. Their distinct structures and properties, such as light absorption, oxidation sensitivity, stiffness, aggregation tendency, and even fluorescence in the case of phytof-luene, contribute to their potential benefits. Furthermore, it is recommended to assess the levels of these carotenoids to evaluate skin carotenoid status accurately.

The papaya mealybug Paracoccus marginatus is an invasive, polyphagous pest and poses a quarantine threat to tropical and subtropical countries. Infested commodity internationally should be undergoing phytosanitary treatment, while irradiation is recommended to replace methyl bromide fumigation. Dose-response tests were conducted on the 2-, 4-, and 6-d-old eggs and gravid females of P. marginatus using the X-ray radiation doses of 15–105 Gy with an interval of 15 Gy, respectively. Radiotolerance was compared using fiducial overlapping and lethal dose ratio (LDR) test, resulting in insignificant difference except for LDR test at LD90 (leading 90% mortality at 95% confidence level (CL)); the estimated dose for 99.9968% mortality at 95% CL was 176.5–185.2 Gy, which was validated in the confirmatory tests using gamma irradiation because gammy and X-rays have equal biological effect on pests. Therefore, a total of estimating 60,386 gravid females of papaya mealybug irradiated with 146.8–185.0 Gy resulted in no F1 nymphs developing. Eggs can therefore be used as an alternative to gravid females for dose-response tests; the recommended minimum dose for phytosanitary treatment of P. marginatus on infested commodity is 185 Gy, with treatment efficacy ≥ 99.9950% at 95% CL.

Petrosamine (1) – a colored pyridoacridine alkaloid from the Belizean sponge, Petrosia sp. that is also a potent inhibitor of acetylcholine esterase (AChE) – was investigated by spectroscopic and computational methods. Analysis of the petrosamine free energy landscapes, pKa and tautomerism revealed an accurate electronic depiction of the molecular structure of 1 as the di-keto form, with net charge of q = +1, rather than a dication (q = +2) under ambient conditions of isolation-purification. The pronounced solvatochromism (UV-vis) reported for 1, and related analogs, was investigated in detail and is best explained by charge delocalization and stabilization of the ground state (HOMO) of 1 rather than an equilibrium of competing tautomers. Refinement of the molecular structure of 1 by QM methods complements published computational docking studies to define the contact points in the enzyme active site that may improve design of new AChE inhibitors based on the pyridoacridine alkaloid molecular skeleton.

Phototherapy is an efficient strategy to respond to oxidative stress and has been in the spotlight in various therapeutic fields through its biological effect, but the exact molecular mechanism has not yet been established. As a result of irradiating RAW264.7 cells with a 630 nm or 850 nm LED with an energy intensity of 0.01J/cm2, cell viability was increased depend on the irradiation time. After H2O2 was added, 630 nm or 850 nm LEDs were irradiated for 10 min or 40 min to increase cell viability by about 1.7- or 1.6-fold, respectively. In addition, 630nm or 850nm LED irradiation showed a significant ROS scavenging effect and significantly reduced TUNEL-positive cells by 45.7% and 37.8%, respectively, compared to cells treated only with H2O2. In the result of flow cytometry, the number of cells in the late apoptosis stage was about 2.3- and 1.8-fold lower than that of the cells treated with H2O2 only, but there was no significance. The Bax/Bcl-2 ratio of cells irradiated with 630 nm or 850 nm LED was significantly lower than that of cells treated with H2O2 only, and the expression of procaspase-3 and cleaved PARP was also significantly expressed in the direction of suppressing cell death. In conclusion, the ROS scavenging activity by 630 nm or 850 nm LED irradiation, leading the expression of cell death pathway proteins in the direction of inhibiting cell death.

This publication describes the influence of residue monomers in synthesized pressure-sensitive adhesives based on acrylics on main performance such as tack, peel adhesion, shear strength and shrinkage in form of transfer tapes used for joining wooden elements in furniture industry. The discussed carrier-free adhesive tapes are synthesized by photo-crosslinking and photopolymerization with UV radiation of photoreactive prepolymers sandwiched between two adhesive siliconized polyester films. The simultaneous crosslinking and polymerization process under UV lamps carried out under UV lamps placed simultaneously above and below the crosslinked photoreactive polymer layer leads to the production of a carrier-free adhesive film. In this test series it were investigated to what how the intensity of UV radiation and the time of its exposure affect the viscosity of photoreactive compositions, and then the content of unreacted monomers in them and, subsequently, the method of their crosslinking and polymerization, and the concentration of the photoreactive crosslinking compound leading to the obtaining of transfer adhesive tapes, and thus on their tray, peel adhesion, shear strength and shrinkage on the surface of the wood.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

The uneven immunogenicity of the attenuated tetravalent dengue vaccine has created the diffi-culty to achieve a balanced protection against all four serotypes of dengue virus (DENV). To overcome this problem, non-replicative-based vaccines have come into focus as their immuno-genicity is adjustable. This approach is excellent for multivalent vaccines but commonly faces the issue of low immunogenicity. In this present study, we developed a non-replicating dengue vaccine composing of UV-inactivated dengue-2 virus (UV-DENV2) and DENV-2 NS1-279 protein encapsidated within nanoparticles. This vaccine candidate was administered in the presence of BCG cell wall cytoskeleton (BCG-CWS) as an adjuvant. We revealed, here, that encapsidated immunogens with BCG-CWS exerted potent activities on both B and T cells and elicited Th-1/Th-2 responses in mice. This was evidenced by strong neutralizing antibody activity with an unde-tectable antibody enhancing activity in a group of mice receiving encapsidated immunogens with BCG-CWS. Importantly, BCG-CWS significantly augmented antibody-mediated comple-ment-fixing activity, strongly stimulated the antigen-specific polyfunctional T cell responses as well as activated mixed Th-1/Th-2 responses specific to DENV2- and NS1-279 antigens. In conclu-sion, BCG-CWS potently adjuvanted the inactivated DENV-2 and subunit DENV immunogens. The mechanism of adjuvanticity remains unclear. This study revealed the potential use of BCG-CWS in vaccine development.

Lichens are unique extremophilic organisms due to their phenomenal resistance to adverse environmental factors, including ultraviolet (UV) irradiation. Melanization plays a special role in the protection of lichens from UV-B stress. In present study, we analyzed the binding of melanins with the components of cell walls of mycobiont of upper cortex in the melanized lichen thalli Lobaria pulmonaria. Using scanning electron and atomic force microscopy, the morphological and nanomechanical characteristics of melanized layer of mycobiont cells were visualized. Melanization of lichen thalli led to the smoothing the surface relief and thickening mycobiont cell walls and resulted in the increase of deformation values and reduction of adhesion properties of lichen thallus. Treatment of thalli with hydrolytic enzymes, especially chitinase and lichenase, enhanced the yield of melanin from melanized thalli and release of carbohydrates, while treatment with pectinase increased the release of carbohydrates and phenols. Our results suggest that melanin by firmly binding with hyphal cell wall carbohydrates, particularly chitin and 1,4-β-glucans, can form associations, strengthen the melanized upper cortex of lichen thalli, and thereby can contribute to lichen survival under UV stress.

Powerful emitters of the ultraviolet C (UVC) light in the wavelength range of 230-280nm are necessary for the development of effective and safe optical disinfection technologies, high-sensitive optical spectroscopy and non-line-of-sight optical communication. This review considers such UVC-emitters with electron-beam pumping of heterostructures with quantum wells in the (Al,Ga)N material system. The important advantages of these emitters include the absence of the critical problem of p-type doping and the possibility of achieving record (up to several tens of watts for peak values) output optical power values in the UVC range. The review consistently considers about a decade of world experience in the implementation of various UV emitters with various types of thermionic, field-emission, and plasma-cathode electron guns (sources) used to excite various designs of active (light-emitting) regions in heterostructures with quantum wells AlxGa1-xN/AlyGa1-yN (x = 0 − 0.5, y = 0.6 − 1) fabricated either by metal-organic chemical vapor deposition or by plasma-activated molecular beam epitaxy. Special attention is paid to the production of heterostructures with multiple quantum wells/two-dimensional(2D) quantum disks GaN/AlN with a monolayer (1ML ~ 0.25nm) thickness, which ensures a high internal quantum efficiency of radiative recombination in the UVC range, low elastic stresses in heterostructures, and a high output UVC-optical powers.

The self-organization properties of C70 fullerene molecules in a xylene/tetrahydrofuran binary mixture were studied for the first time by optical absorption, refractometry, and dynamic light scattering. A correlation has been established between the change in the refractive index of the C70/xylene/tetrahydrofuran solution and the degree of self-organization of C70 molecules in the medium at various concentrations and storage periods of the solution. It is shown that the features of the optical absorption spectrum of C70/xylene/tetrahydrofuran at a fixed low concentration of the fullerene are sensitive to its storage time. It was determined that the beginning time of the formation of C70 nanoclusters and their final size depend on the concentration of fullerene and the time of keeping the solution. The observed nature of the C70 fullerene solution in a binary mixture may help to elucidate the mechanism of self-organization in the future.

Three octahedral iron(III) nitrate complexes with dimethylated urea ligand isomers, [hexakis(N,N’-dimethylurea-O)iron(III)] nitrate (compound 1), trans-[diaquatetrakis(N,N-dimethylurea-O)iron(III)] nitrate (compound 2) and [hexakis(N,N-dimethylurea-O)iron(III)] nitrate trihydrate (compound 3) were prepared and characterized with single crystal X-ray diffraction, IR, Raman and UV-VIS methods. In compounds 1 and 3, six dimethylurea ligands coordinate to the central FeIII ion via the oxygen in octahedral geometry and the ligands are arranged in a propeller-like manner, dividing the complex cations into two sides. In compound 1, the dimethylurea propellers screw in the opposite direction on the two sides of the complex and in compound 3, they are arranged with the same handedness on the two sides. The complexes have helical chirality. The two sides of the complex cations differ not only in the rotation direction of the ligands but also in the hydrogen bond formation. On one side of the complex cation, the ligands form intermolecular hydrogen bonds only with the crystal waters, meanwhile on the other side of the complex, the ligands form hydrogen bonds only with the nitrate ions. In compound 2, [Fe(N,N-dimethylurea)4(H2O)2]3+ cations form layers that are separated by interconnected NO3- ions forming a hydrogen bonding system and connecting the complex cations A-s and B-s. The three crystallographically different nitrate ions each form four hydrogen bonds in a way that they have one bidentate O atom and two monodentate O atoms, however, the anions differ in their hydrogen bonding. The spectroscopic characteristics of compound 2 were determined by IR measurements on the deuterated compound 2 as well.

In the article, we are trying to find a general law that describes the physical properties of a complex compound through the same physical properties of compound elements. For metal alloys operated under extreme conditions - neutron and proton irradiations and thermal heating, the mechanical properties of these alloys and their elements have been studied. It turned out that the ultimate tensile strength of tantalum alloys used in the design of space reactors can be expressed in terms of the weighted sum of the ultimate tensile strengths of its elements in the range of neutron doses: (0 - 0.96) displacement per atom (dpa) for Ta–10W alloy and (1.4 - 1.7) dpa for T–111 alloy with a neutron energy of more than 0.1 MeV. For tungsten binary alloys used in the design of fusion reactors, the Vickers hardness can also be expressed in terms of the weighted sum of the Vickers hardnesses of the alloy elements in the range of proton irradiation doses: (0 - 0.05) dpa for W-1%Re alloy, (0.05 - 0.2) dpa for W-3%Re alloy and (0.05 - 1) dpa for W-1%Ta with a proton energy of 1 MeV.

The aim of this work was to investigate a new, simple one-pot combustion synthesis technique for creating sulphur-based CuS/ZnS p-n heterojunction nanocomposite photocatalysts. The study examined the photocatalytic activity and reusability of these nanocomposites in removing rhodamine B (RhB) dye under visible light irradiation. Various methods of characterisation were employed to determine the properties of the materials, including particle morphology, crystalline phases and bandgap energy. The intrinsic reaction parameters, such as catalyst loading, pH level of the solution, and initial pollutant concentration, were varied to establish the optimal photo-degradation conditions. The results showed that a binary CuS/ZnS catalyst with a 10 gL-1 loading, at pH 5, degraded 97% of 5 ppm RhB dye after 270 minutes of visible light irradiation. Addition-ally, this composite catalyst exhibited excellent chemical stability and reusability, achieving 83% RhB dye removal after five recycling runs. Scavenger tests identified the photogenerated holes (h+) and superoxide free radicals (•O2) as the primary reactive species responsible for degradation. This study provides valuable insight into the design of highly efficient nanomaterials for removing organopollutants in wastewater, and a possible reaction mechanism is proposed.

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

Base excision repair (BER) is a cellular process that removes damaged bases arising from exogenous and endogenous sources including reactive oxygen species, alkylation agents, and ionizing radiation. BER is mediated by the actions of multiple proteins that work in a highly concerted manner to resolve DNA damage efficiently to prevent toxic repair intermediates. During the initiation of BER, the damaged base is removed by one of 11 mammalian DNA glycosylases resulting in abasic sites. Many DNA glycosylases are product inhibited by binding to the abasic site more avidly than the damaged base. Traditionally apurinic/apyrimidinic endonuclease, APE1, was believed to help turnover the glycosylases to undergo multiple rounds of damaged base removal. However, in a series of papers from our laboratory we have demonstrated that UV-damaged DNA binding protein (UV-DDB) stimulates the glycosylase activities of human 8-oxoguanine glycosylase (OGG1), MUTY DNA glycosylase (MUTYH), alkyladenine glycosylase/N-methylpurine DNA glycosylase (AAG/MPG), and single-strand selective monofunctional glycosylase (SMUG1), between three-to-five-fold. Moreover, we have shown UV-DDB can assist chromatin decompaction facilitating access of OGG1 to 8-oxoguanine damage in telomeres. This review summarizes the biochemistry, single-molecule, and cell biology approaches that our group used to directly demonstrate the essential role of UV-DDB in BER.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

The leaves of Ligustrum robustum have been applied as Ku-Ding-Cha, a functional tea to clear heat and remove toxins; and served as a folk medicine to deal with diabetes, obesity, and hypertension. Trans-p-hydroxycinnamic acid and its esters, which were isolated from the leaves of L. robustum, might be a new resource to prevent diabetes and its complications because of their strong -glucosidase and fatty acid synthase (FAS) inhibitory activities and antioxidant effect. However, the quantitative analytical method for trans-p-hydroxycinnamic acid and its esters in the leaves of L. robustum hasn’t been reported so far. In addition, it was difficult and troublesome to analyze no less than 34 trans-p-hydroxycinnamic acid esters by usual HPLC. Therefore, a new HPLC-UV method using hydrolyzation with sodium hydroxide for quantitation of trans-p-hydroxycinnamic acid and its esters in the leaves of L. robustum was developed in the present study. The optimal hydrolyzation conditions were as follows: 1 mL sodium hydroxide aqueous solution (1 M) was added into 1 mL the extract of L. robustum and incubated at 80 °C for 2 h , and then 1 mL hydrochloride (1 M) solution was added. HPLC analysis was performed in reverse phase mode using a C-18 column, eluting with methanol-0.1% acetic acid aqueous solution (40:60, v/v) in isocratic mode at a flow rate of 1.0 mL/min, and detecting at 310 nm. The analytical method was simple and rapid, which simplified greatly the analytical process. The method was validated in terms of linearity, limit of detection (LOD), limit of quantification (LOQ), precision, and accuracy. High linearity was demonstrated with correlation coefficient of 1.000 for trans-p-hydroxycinnamic acid. The LOD and LOQ values were 1.55 and 4.69 μg/mL, respectively. The relative standard deviations (RSD) of intra-day and inter-day variabilities for trans-p-hydroxycinnamic acid were less than 2%. The percentage recovery of trans-p-hydroxycinnamic acid was 101.2% ± 0.8%. Finally, the proposed method was applied successfully to the determination and comparison of the contents of trans-p-hydroxycinnamic acid and its esters in various extracts of the leaves of L. robustum. The 60%-70% ethanol extracts of L. robustum showed the highest contents of free trans-p-hydroxycinnamic acid (3.96-3.99 mg/g), and the 50%-80% ethanol extracts of L. robustum displayed the highest contents of trans-p-hydroxycinnamic acid esters (202.6-210.6 mg/g). The method can be applied also to the quality control of the products of L. robustum.

The emergence of Non-Ionizing Radiation (NIR) has stimulated the growth and advancement of technological civilization. NIR is ubiquitous; it has helped improve all fields and even deepened democratic processes through the transfer of data and electronic transmission of results etc. A breathtaking part of NIR is its recent application in the treatment of adverse health effects through radiofrequency ablation, phototherapy, etc. as summarized in Table 1. The benefits of NIR are enormous, however, technological civilization has not come without a cost; some of the adverse health effects associated with NIR include skin cancers, sleep disorders, photo-aging, etc. as summarized in Table 2. Therefore, with the rapid and sporadic increase in the sources of NIR from Natural and Artificial sources including fossil fuel burning, Starlink technology, mobile phones, mobile base antennas, etc., background radiation is expected to rise beyond the exposure limit leading to health illnesses. Intrinsically, there is a dare need to marry concerns that evolve with this growth. Hence, this review article aims to congregate the health hazards associated with NIR and the state-of-the-art applications of NIR in medicine and the health sector in Nigeria being a developing country. Part of our recommendations is that the government at all levels should set up enforcement agencies and policies to drive strict adherence to NIR as provided by ICNIRP; frequent-periodic assessments of background radiation in public places should be carried out due to the increasing sources. In addition, further research is needed to ascertain the health hazard from emerging sources of NIR like Starlink technology and to substantiate findings of non-thermal effects.

In the present research, groups of nanolayered structures and nanohybrids based on organic green dyes and inorganic species are designated to act as fillers for PVA for inducing new optical sites and increasing its thermal stability through producing polymeric nanocomposites. In this trend, different percentages of Naphthol green B were intercalated as pillars inside the Zn-Al nanolayered structures to form green organic-inorganic nanohybrids. The two-dimensional green nanohybrids were identified by X-ray diffraction, TEM and SEM. According to the thermal analyses, the nanohybrid, which has the highest amount of green dyes, was used for modifying the PVA through two series. In the first series, three nanocomposites were prepared depending on the green nanohybrid as prepared. In the second series, the yellow nanohybrid, which was produced from the green nanohybrid by thermal treatment, was used to produce another three nanocomposites. The optical properties revealed that the polymeric nanocomposites depending on green nanohybrids became optical-active in UV and visible regions because the energy band gap decreased to be 2.2 eV. In addition, the energy band gap of the nanocomposites depended on yellow nanohybrids was 2.5 eV. The thermal analyses indicated that the polymeric nanocomposites are thermally more stable than that of the original PVA. Finally, the dual functionality of organic-inorganic nanohybrids that produced from the confinement of organic dyes and the thermal stability of inorganic species converted the non-optical PVA to optical-active polymer in a wide range with high thermal stability

In this work, we report manganese phthalocyanine (MnPc) films obtained by ultrasonic spray-pyrolysis technique at 40°C deposited on glass substrate subjected to thermal annealing at 100 °C and 120°C. The MnPc films were characterized by UV/Vis spectroscopy, Raman spectroscopy, X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The absorption spectra of the MnPc films were studied in a wavelength range from 200 to 850 nm, where the characteristic bands of a metallic phthalocyanine known as B and Q bands were observed in this range of the spectrum. The optical energy band (Eg) was calculated by the Tauc equation. It was found that for these MnPc films, the Eg has the values of 4.41, 4.46 and 3.58 eV corresponding to as deposited, annealing 100°C and 120°C, respectively. The Raman spectra of the films showed their characteristic vibrational modes of the MnPc films. In X-ray diffractograms of these films, the characteristic diffraction peaks of a metallic phthalocyanine are observed, presenting a monoclinic phase. SEM images of these films were studied in cross section obtaining thicknesses of 2, 1.2 and 0.3 μm to as deposited, annealing 100°C and 120°C, successively. Also, in the SEM images of these films, both the average particle sizes ranging from 4 to 0.041 µm and the average diameter from 4.8 to 0.091 μm were obtained. The results agree with those reported in the literature for MnPc films deposited with other techniques.

The process of ultrasonic atomization involves a series of dynamic/topological deformations of free surface, though not always, of a bulk liquid (initially) below the air. This study focuses on such dynamic interfacial alterations realized by changing some acousto-related operating conditions, including ultrasound excitation frequency, acoustic strength or input power density, and the presence/absence of a “stabilizing” nozzle. High-speed, high-resolution imaging made it possible to qualitatively identify four representative transitions/demarcations: 1) the onset of a protrusion on otherwise flat free surface; 2) the appearance of undulation along the growing protuberance; 3) the triggering of emanating beads fountain out of this foundation-like region; and 4) the induction of droplets bursting and/or mist spreading. Quantitatively examined were the two-parameters specifications—on the degrees as well as induction—of the periodicity in the protrusion-surface and beads-fountain oscillations, detected over wider ranges of driving/excitation frequency (0.43–3.0 MHz) and input power density (0.5–10 W/cm2) applied to the ultrasound transducer of flat surface on which the nozzle was mounted or not. The resulting time sequence of images processed for the extended operating ranges, regarding the fountain structure pertaining in particular to recurring beads, confirms the wave-associated nature, i.e., their size “scalability” to the ultrasound wavelength, predictable from the traveling wave relationship. The thresholds in acoustic conditions for each of the four transition states of the fountain structure have been identified—notably, the onset of plausible “bifurcation” in the chain-beads diameter below a critical excitation frequency.

The review starts by highlighting the significance of nuclear power plants in contemporary world, especially its indispensable role in the global efforts to reduce CO2 emissions. Then, it describes the impact of irradiation on microstructure and mechanical properties of reactor structural materials. The main part provides the reader with a thorough overview of crystal plasticity models developed to address the irradiation effects so far. All three groups of most important materials are included. Namely, the Zr alloys used for fuel cladding, austenitic stainless steels used for reactor internals and ferritic steels used for reactor pressure vessel. Other materials, especially those considered for construction of future fission and fusion nuclear power plants, are also mentioned. The review pays also special attention to ion implantation and instrumented nanoindentation which are a common way to substitute costly and time-consuming neutron irradiation campaigns.

Increased screen time during the COVID-19 pandemic and the accelerated incorporation of technology into daily practices have directly contributed to the increased prevalence of eye disease. The human eye is not built for continual technological use and must adjust to exposure to digital screens. Overexposure to technology can result in eye strain and an increased risk of eye diseases such as myopia with complications later in life, including retinal tears, cataracts, and macular degeneration. As vision and ocular diseases become more prevalent, the study of eye diseases, including their causes and treatments, is especially relevant. There is a need to prevent ocular diseases before they become a burden to individuals, their families, and their communities by better understanding the pathophysiology of ocular diseases. Several ocular diseases are thought to be caused by imbalances in reactive oxygen species (ROS) and autophagy. ROS refers to a class of highly reactive oxygen-containing molecules that can undergo damaging reactions with other molecules in the cell. Autophagy is a cellular process of self-eating whereby damaged, harmful, or dead material in cells is broken down to maintain cellular homeostasis. This paper discusses the role of ROS and autophagy in the pathogenesis of computer vision syndrome (CVS), digital eye strain (DES), myopia, cataracts, glaucoma, diabetic retinopathy (DR), age-related macular degeneration (AMD), optic nerve crush injury (OCN), optic nerve gliomas, and retinoblastoma. Lifestyle changes such as limiting screen time, ensuring adequate exposure to evening sunlight, and using blue light protection measures or protective eyewear are important in the prevention of eye disease. Nutrition also contributes significantly to eye health. A balanced diet rich in vitamins and antioxidants may help to prevent ROS and autophagy imbalance-induced eye disease. Medical and surgical treatments become necessary when preventative measures fail. This paper also addresses how government measures to decrease the onset of eye disease, including targeted programs to increase access to fresh vegetables and fruits in food deserts, are a critical macro-level avenue to reduce eye disease prevalence in the US, which according to the National Eye Institute, costs $139 billion yearly.

The spectrophotometric methods of determination of the active pharmaceutical ingredients meloxicam and nimesulide were reviewed, and a simple UV-spectrophotometric method for the determination of these active pharmaceutical ingredients in industrial equipment cleaning validation samples were proposed. The methods are based on extraction of the residual quantities of meloxicam and numesulide from the manufacturing equipment surface by the concentrated sodium carbonate solution, and the subsequent UV-spectrophotometric determination of the basic forms of the drugs at the wavelength of 362 nm for meloxicam and at 397 nm for nimesulide. The calibration graphs are linear in the range from 5 to 25 mg/L of both nimesulide and meloxicam, the molar attenuation coefficients are 6100 m2/mol for nimesulide and 9100 m2/mol for meloxicam, the limit of detection is 0.8 mg/L for nimesulide and 1.9 mg/L for meloxicam, the limit of quantification is 2.5 mg/L for nimesulide and 5.8 mg/L for meloxicam, the methods are selective with respect to the common excipients, show a good accuracy (the relative uncertainty does not exceed 4%) and precision (the relative standard deviation does not exceed 5%), do not require lengthy sample preparation and sophisticated laboratory equipment and are suitable for the routine analysis of cleaning validation samples.

TomoBreast hypothesized that hypofractionated 15 fractions/3 weeks image-guided radiation therapy (H-IGRT) can reduce lung-heart toxicity, as compared with normofractionated 25-33 fractions/5-7 weeks conventional radiation therapy (CRT). 123 women with stage I-II operated breast cancer were randomized to receive CRT (N=64) or H-IGRT (N=59). The primary endpoint used a four-items measure of the time to 10% alteration in any of patient self-reported measure, physician clinical evaluation, echocardiography or lung function tests, analyzed by intention-to-treat without exclusion. Results found comparable survivals, but H-IGRT significantly reduced the toxicity measured by lung diffusion capacity and alveolar volume as compared with CRT, G1 in 53% (31/59) versus 72% (44/61) patients, P=0.006; G2, 29% versus 48%, P=0.020. H-IGRT significantly reduced the risk of composite cardio-pulmonary alteration at 5 years, 10.2% versus 26.7%, P=0.024. In conclusion, TomoBreast is a proof-of-concept that image-guided radiation-therapy can improve the overall balance of lung-heart outcomes in breast cancer adjuvant therapy. Furthermore, the significance of the findings supports the efficacy of a small trial size design, which can be critical when clinical research resources are limited.

The natural compounds of boron have many applications, including as dietary supplement. Communication is based on the discovery that diester chlorogenoborate complex can be detected and quantified from green coffee bean. The study reports that such diester molecule can also be synthesized in stable form by direct reaction of boric acid and chlorogenic acid, in a mixture of acetonitrile–water (1:1, v/v), left to evaporate over a period of 48 hours, at room temperature, resulting a spirocyclic form (diester complex). The diester complex, with its molecular structure and digestibility attributes has potential application as prebiotic in gut health, oral health and as micronutrient essential for microbiota to human and animals.

An HPLC method for indicating stability was developed, created, and confirmed for the quantification measurement of recombinant human erythropoietin in large quantities as well as dosage forms. An isocratic separation was accomplished using a Thermo Biobasic C18 (250 mm 4.6 mm i.d., 300Ao, 5 m) column with a flow rate of 1.0 mL min-1 as well as a UV detector to monitor the eluate at 278 nm. Acetonitrile, 0.05 mM potassium dihydrogen phosphate (80:20 v/v), and orthophosphoric acid adjusted to 4.0 made up the mobile phase. The drug was exposed to oxidative stress, hydrolysis, and photodegradation to simulate stress conditionsRecombinant Human Erythropoietin, the parent compound, was eluted at roughly 6.675 minutes, as well as all byproducts have been entirely disconnected inside an overall analytical run time of about 15 minutes. To identify quantification limits of 0.05 and 0.2 g mL-1, respectively, the method was linear over a concentration range of 1-6 g mL-1 (r = 0.9989). Recombinant Human Erythropoietin can be measured accurately, selectively, sensitively, and precisely using this method both in dosage form and in bulk. Stress-induced degradation products did not interact with the identification of Recombinant Human Erythropoietin, indicating that the assay is stable.

Additive manufacturing or 3D printing applying polycaprolactone-(PCL)-based medical devices represents an important branch of tissue engineering, where the sterilization method is a key process for further safe application in vitro and in vivo. In this study, the authors intend to access the most suitable gamma radiation conditions to sterilize PCL-based scaffolds in a preliminary biocompatibility assessment, envisioning future studies for airway obstruction conditions. Three radiation levels were considered, 25 kGy, 35 kGy and 45 kGy and evaluated as to their cyto- and biocompatibility. All three groups presented biocompatible properties, indicating an adequate sterility condition. As for the cytocompatibility analysis, devices sterilized by 35 kGy and 45 kGy showed better results, with the 45 kGy showing overall improved outcomes. This study allowed to select the most suitable sterilization condition for PCL-based scaffolds, aiming at immediate future assays, by applying 3D-customized printing techniques to specific airway obstruction lesions of the trachea.

The Dead Sea basin is the lowest terrestrial site on the globe and is internationally recognized as a photoclimatotherapy center. Since the last century, questions raised regarding the possible presence of a unique incident ultraviolet irradiation, allowing successful treatment of psoriasis, atopic dermatitis and other dermatological diseases. Aim: Determine the characteristics of the solar ultraviolet irradiation and understand the mechanism of action of photoclimatotherapy while applying the results to clinical protocols of treatment. Methods: A meteorological station was established at the Dead Sea basin to continuously measure global, UVB and UVA irradiation. The same irradiation parameters are also being monitored continuously by a set of identical ultraviolet irradiation instruments installed on the campus of the Ben-Gurion University of the Negev, in Beer Sheva. Results: This study details the results of these long-term measurements, ae well as their correlation with the success obtained by clinicians treating psoriasis patients. Conclusions: A database of more than 25 years has enabled the medical staff to establish tailor-made protocols for sun-exposure time intervals as a function of particular month and hour of day. The availability of such information has significantly improved the results of photoclimatotherapy for psoriasis and at the same time increasing the safety of sun-exposure at the Dead Sea.

Using optical characterization, it is evident that the spin state of the spin crossover molecular complex [Fe{H2B(pz)2}2(bipy)] (pz = tris (pyrazol-1-1y)-borohydride, bipy = 2,2’-bipyridine) depends on the ferroelectric polarization of an adjacent thin film of the polymer ferroelectric polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP). The UV-Vis spectroscopy reveals that room temperature switching of [Fe{H2B(pz)2}2(bipy)] molecules in bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] as a function of ferroelectric polar polarization. The electric polarity dependence of bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] shows a strong dependence on the thickness of the PVDF-HFP layer. The PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] interface may affect polarization retention in the PVDF-HFP thin film limit.

This joint experimental-theoretical work focuses on molecular and photophysical properties of the spiropyran-containing amphiphilic molecule in organic and aqueous solutions. Being dissolved in tested organic solvents, the system demonstrates positive photochromism, i.e. upon UV stimulus the colorless spiropyran form is transformed into colorful merocyanine isomer. However, aqueous solution of the amphiphile possesses a negative photochromism: the orange-red merocyanine form turns to be thermodynamically more stable in water, and both UV and vis stimuli lead to the partial or complete photobleaching of the solution. The explanation of this phenomenon is given on the basis of density functional theory calculations and classical modeling including thermodynamic integration. The simulations reveal that stabilization of merocyanine in water proceeds with the energy of ca. 70 kJ mol−1, and that the Helmholtz free energy of hydration of merocyanine form is 100 kJ mol−1 lower as compared to the behavior of SP isomer in water. The explanation of such a difference lies in the molecular properties of the merocyanine: after ring-opening reaction this molecule transforms into a zwitterionic form, as evidenced by the electrostatic potential plotted around the opened form. The presence of three charged groups on the periphery of a flat conjugated backbone stimulates the self-assembly of merocyanine molecules in water, ending up with the formation of elongated associates with stack-like building blocks, as shown in molecular dynamics simulations of the aqueous solution with the concentration above critical micelle concentration. Our quantitative evaluation of the hydrophilicity switching in spiropyran/merocyanine containing surfactants may prompt the search for new systems, including colloidal and polymeric ones, aiming at remote tuning of their morphology, which could give new promising shapes and patterns for the needs of modern nanotechnology.

The aim of this study, for determination of verteporfin in real samples (simulated body fluid, and simulated tears, 0.9% isotonic sodium chloride solution, Lactated Ringer IV solution for infusion, 5% dextrose IV solution for infusion, lemon juice and drinking water) was the method validation and to examined by HPLC-DAD-UV. Metod validation parameters such as specificity, linearity, precision, accuracy, robustness, limit of detection (LOD) and limit of quantitation (LOQ) for verteporfin were validated and developed according to the International Conference on Harmonization (ICH) Q2 R1 guidelines. The LOD and LOQ for verteporfin were found 0.06 µg/L and 0.2 µg/L, respectively. The recovery values of the optimization and validation for verteporfin were found in the range of 97.5-100.7%. The relative standard deviations (RSD) for vertepofin were <1%. The developed method was successfully applied to real samples with high accuracy and the recoveries (%) from real samples were 99.9, 100, 98.2, 99.2, 99.4, 98.8 and 99.4, respectively.

Euglenoids are a common component of primary producers in high acidic and organic shallow freshwater systems. They are free-living photosynthetic motile flagellates exhibiting rapid responses to various external stimuli including chemical pollution. The unique combination of diverse physiological processes of Euglena such as photosynthesis, movement, and orientation offers a range of sensitive criteria that respond to aquatic pollutants. This has led to the development of several acute and chronic assay methods to monitor the adverse impacts of potent toxicants in aquatic ecosystems. Euglenoids also reflect the consequences of physical stress factors such as UV radiation. This review summarizes the ecotoxicity studies using euglenoid flagellates as model species and their potential to contribute toward rapid screening of ecological impacts of pollution in the aquatic environment. Factors determining the reliability of Euglena tests are outlined.

More than twenty-five years ago the Global Solar UV index (UVI) has been introduced as a simple means of visualizing the intensity of ultraviolet radiation and to alert people to the need for sun protection. In our survey among directors of 436 kindergartens in southern Germany we investigated the level of awareness and knowledge about the UVI as well as the practical consequences for sun protection in kindergartens. Less than half of the directors (n=208, 47.7%) had ever heard of the UVI, and only a small minority of them (n=34, 8.7%) used the daily UVI information to adapt sun protective measures in their kindergartens. Detailed knowledge about the UVI was a rarity among the respondents. The proportion of respondents with self-perceived detailed UVI knowledge was five times higher than actual knowledge assessed by an in-depth structured interview using open-ended questions about the UVI (14.2% vs. 2.8%). No clear relationship of UVI awareness, knowledge, and use to directors' age and gender was found. The UVI-related variables also showed no association with directors' knowledge of risk factors for skin cancer and their attitudes towards tanned skin. Overall, the results paint a sobering picture regarding the penetration of the UVI into sun protection policies of German kindergartens. Future public health campaigns should target increasing awareness and understanding of the UVI as well as its importance for sun protection of children.

Gene expression variations of plant leaf are investigated by irradiating seed and leaf with oxygen or air plasmas. Enhancement of leaf growth is induced by oxygen plasma irradiation on seeds, which is supported by increased gene expression for protein synthesis, oxidative-reduction reactions and decreased gene expression concerning DNA methylation and histone modification. Suppression of leaf growth is observed by the oxygen plasma, which would be owing to increased gene expression concerning heat shock protein and redox reaction, and decreased expression of photosynthesis and glycoprotein. Also, gene expression variation due to air plasma irradiation is almost same as that of oxygen plasma. Active oxygen species are major factors in both oxygen and air plasmas for the variation of gene expressions in plant.

To investigate the photosynthetic change characteristics of mango leaves under enhanced UV-B radiation, adult ‘Tainong No. 1’ mango (Mangifera indica) trees were treated (N=nine individuals) with simulated enhanced UV-B radiation [24 and 96 kJ/(m2·d)] in the field, and the photochemical reactions, activities of key enzymes in carbon assimilation, and the expression of genes were observed. The results showed that compared with the control, there was a decrease in tree yield and nutritional flavor quality of the fruits under the 96 kJ/(m2·d) treatment, while no significant changes were observed under 24 kJ/(m2·d). After 20 or 40 days, leaves’ net photosynthetic rate (Pn), stomatal conductance (Sc), transpiration rate (Tr), intercellular CO2 concentration (Ci), and chlorophyll a/b under exposure to 96 kJ/(m2·d) of UV-B were significantly lower than in the control, whereas chlorophyll a, chlorophyll b, carotenoids, Hill reaction activity, photochemical quenching coefficient (qP), and Rubisco activities were significantly higher. By contrast, the Hill activity and Rubisco activity under 24 kJ/(m2·d) were significantly higher than the control, while Pn, Sc, Tr, Ci, and the content of photosynthetic pigments were similar to the control. The expression of gene coding the Rubisco big subunit (rbcL) was inhibited by the 96 kJ/(m2·d) treatment. We conclude that stomatal limitation was directly induced by 96 kJ/(m2·d), resulting in the inhibition of photosynthesis and the reduction in yield and deterioration of the quality of mango.