The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

In recent years, with the increasing research and development of the LED industry which contains GaN, it is expected that there will be a large amount of related wastes in the future. Especially the gallium has extremely high value of economic, therefore, it is necessary to establish the recycling system of the GaN waste. However, GaN is a direct-gap semiconductor and with high energy gap, high hardness, and high melting point make it difficult to recycle. Therefore, this study will analyze the physical characteristics of LED wastes containing GaN and carry out various leaching method to leach the valuable metals from the waste optimally. Different acids are used to find out the best reagent for leaching the gallium. Different experimental parameters are discussed such as the effect of the different acid agents , concentration, pressure, solid-liquid mass ratio, temperature, and time which influence the leaching efficiency of the gallium. In this study, various leaching methods which effect the leaching efficiency of the gallium are compared and the advantages and disadvantages are discussed. Finally, pressurized acid leaching method is preferred to leach the GaN waste, and hydrochloric acid is used as the leaching solution because of its better leaching efficiency of gallium. Eventually, the leaching efficiency of the gallium can reach to 98%.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

Solid-state lighting has been replacing conventional lighting in the market, raising concerns for implementing an efficient end-of-life management system. Since LED waste streams have not been quite dominant, characterization studies (product-level characteristics, component-wise information, bill of materials, diversity, and differences) are inconsistent and having substantial gaps. This study investigates the end-of-life LED lamp literature, focusing on the bill-of-materials, and reveals that the characterization procedure suffers from a severe lack of sample representativeness. Consequently, characterization results are widely varied and not generalizable. Moreover, most of the studies did not inform and document the detailed sample characteristics, precluding the possibility of identifying reasons for variation. Combining available information from the recent studies, we present a mass distribution at the component level, exemplifying the prospect for meeting EU regulatory limit and the need for more insight at the lamp and component level. To fill the disconnection between lamp level characteristics and component and material content, we propose a characterization protocol that carefully documents lamp, component, and material level information by establishing a lamp-component–material composition nexus. The protocol may help researchers, policymakers, and industrial stakeholders conduct a systematic characterization, analyze complexities and prepare for a sustainable solution.

Color plays an important part in human activities, affects circadian cycle and decision making process. Therefore, it is important to investigate human judgment under different color of illumination, especially, because color perception is subjective. In this study, we developed required instrumentation to control the red (R), green (G), Blue (B) and Amber (A) colored light emitting diode (LED) lamp for carrying out Magneto Encephalography (MEG) brain scan. We developed a software to generate all the colors in the visual spectrum, predefined white light combinations and saturation of an illuminated objects by using RGBA color pallet. The lamp is required to control from outside of the MEG electromagnetically shielded room with the LED lamp located inside the MEG room. Hence, USB is used for the communication mode. The feasibility of using LED lamp with MEG brain scanner has been validated for bio-medical and psychological MEG experiments.

The halotolerant photoautotrophic marine microalga Dunaliella salina is one of the richest sources of natural carotenoids. Here we investigated the effects of high intensity blue, red and white light from light emitting diodes (LED) on the production of carotenoids by strains of D. salina under nutrient sufficiency and strict temperature control favouring growth. Growth in high intensity red light was associated with carotenoid accumulation and a high rate of oxygen uptake. On transfer to blue light, a massive drop in carotenoid content was recorded along with very high rates of photo-oxidation. In high intensity blue light, growth was maintained at the same rate as in red or white light, but without carotenoid accumulation; transfer to red light stimulated a small increase in carotenoid content. The data support chlorophyll absorption of red light photons to reduce plastoquinone in photosystem II, coupled to phytoene desaturation by plastoquinol:oxygen oxidoreductase, with oxygen as electron acceptor. Partitioning of electrons between photosynthesis and carotenoid biosynthesis would depend on both red photon flux intensity and phytoene synthase upregulation by the red light photoreceptor, phytochrome. Red light control of carotenoid biosynthesis and accumulation reduces the rate of formation of reactive oxygen species (ROS) as well as increases the pool size of anti-oxidant.

LIFI was first introduce by Professor Harald Haas on July 2011. Light fidelity (LI-FI) may be a technology which uses light as a medium to travel from one place to a different. It uses Light like Light Emitting Diode (LED) visible radiation Communication (VLC) for data Transferring and Internet connection. LIFI may be a technique which uses light as a medium because it uses light to travel it's 20 times faster than any WIFI within the world. during this paper we speak about things like what's LIFI and the way it's better then WIFI why we want LIFI and What changes did bring LIFI in our Future LIFI. How it'll make IOT devices far better than before The Technique to implement LIFI and also the problem we face of implementation of LIFI

Photobiomodulation (PBM) is a procedure that uses light to modulate cellular functions and bio-logical processes. Over the past decades, PBM has gained considerable attention for its potential in various medical applications due to its non-invasive nature and minimal side effects. This narrative review article examines the existing literature on PBM, encompassing research studies, clinical trials, and technological developments. This review highlights the mechanisms of action underlying PBM, including the interaction with cellular chromophores and the activation of in-tracellular signaling pathways. The evidence from clinical trials and experimental studies to evaluate the efficacy of PBM in clinical practice is summarized with a special emphasis on der-matology. Furthermore, advancements in PBM technology, such as novel light sources and treat-ment protocols, are discussed in the context of optimizing therapeutic outcomes and improving patient care. This narrative review underscores the promising role of PBM as a non-invasive therapeutic approach with broad clinical applicability. Despite the need for further research to develop standard protocols, PBM holds great potential for addressing a wide range of medical conditions and enhancing patient outcomes in modern healthcare practice.

In recent years, photobiomodulation (PBM) has been recognized as a physical therapy in wound management. Despite several published research papers, the mechanism underlying photobiomodulation is still not completely understood. The investigation about application of blue light to improve wound healing is a relatively new research area. Tests in selected patients evidenced a stimulation of the healing process in superficial and chronic wounds treated with a blue LED light emitting at 420 nm; a study in animal model pointed out a faster healing process in superficial wound, with an important role of fibroblasts and myofibroblasts. Here we present a study aiming at evidencing the effects of blue light on the proliferation and metabolism in fibroblasts and keratinocytes. Different light doses were used to treat the cells, evidencing inhibitory and stimulatory effects. Electrophysiology was used to investigate the effects on membrane currents, while Raman spectroscopy revealed the mitochondrial Cytochrome C (Cyt C) oxidase dependence on blue light irradiation. In conclusion, we observed that the blue LED light can be used to modulate the activity of human fibroblasts, and the effects in wound healing are particularly evident when studying the fibroblasts and keratinocytes co-cultures.

More than 1.1 billion people lack access to electricity in the world, among them 600 million are in sub-Saharan African countries. The socio-economic life of the rural communities is highly affected by electricity supply. The demanding Interest for growth and development in developing countries led to a renewed interest in solar lights. Liter of the night light is a solar-powered light that is constructed from waste plastic bottles which light up the rural community. This paper is about experimental analysis of liter of night light for potential use in rural electrification. The technology uses environmentally friendly and locally available materials. The system is provided with battery storage, which allows it to operate for 13.5 hours continuously at full charge. Solar radiation is converted by PV solar panel to electric current. Circuit board is developed and fabricated to regulate and deliver a consumable amount of voltage by the rechargeable lead-acid battery. After testing five different solutions, the study found out that vinegar solution as the optimal solutions for the technology that can deliver 27lux of light to the surrounding. Simultaneously the study found out, that the light that is emitted from the bottle bulb is a function of volume, depth and solution type. And for this relationship curves are developed. And, the technology can be used for rural communities as it is.

The Hennovation project, an EU H2020 funded thematic network, aimed to explore the potential value of practice-led multi-actor innovation networks within the laying hen industry. The project proposed that husbandry solutions can be practice-led and effectively supported to achieve durable gains in sustainability and animal welfare. It encouraged a move away from the traditional model of science providing solutions for practice, towards a collaborative approach where expertise from science and practice were equally valued. During the 32-month project, the team facilitated 19 multi-actor networks in 5 countries through 6 critical steps in the innovation process: problem identification, generation of ideas, planning, small scale trials, implementation and sharing with others. The networks included farmers, processors, veterinarians, technical advisors, market representatives and scientists. The interaction between the farmers and the other network actors, including scientists, was essential for farmer innovation. New relationships emerged between the scientists and farmers, based on experimental learning and the co-production of knowledge for improving laying hen welfare. The project demonstrated that a practice-led approach can be a major stimulus for innovation with several networks generating novel ideas and testing them in their commercial context. The Hennovation innovation networks not only contributed to bridging the science-practice gap by application of existing scientific solutions in practice but more so by jointly finding new solutions. Successful multi-actor, practice-led innovation networks appeared to depend upon the following key factors: active participation from relevant actors, professional facilitation, moderate resource support and access to relevant expertise. Farmers and processors involved in the project were often very enthusiastic about the approach, committing significant time to the network’s activities. It is suggested that the agricultural research community and funding agencies should place greater value on practice-led multi-actor innovation networks alongside technology and advisor focused initiatives to improve animal welfare and embed best practices.

The degradation of the persistent compound perfluorooctanoic acid (PFOA) in water by ultraviolet light in the presence and absence of hydrogen peroxide was examined. A laboratory experiment was designed to answer the question: is UV spectrophotometry feasible for PFOA research? Spectrophotometry was able to measure the degradation of PFOA, but a very high concentration was required. The 1 mg/L used is very concentrated when compared to the 70 ng/L suggested level in drinking water. A UV/Visible diode array scanning spectrophotometer was used to measure changes in PFOA concentrations after 15-minute exposures to ultraviolet light and ultraviolet light with hydrogen peroxide. A noticeable drop in concentration was measured for a 1 mg/L sample. The reaction kinetics were calculated and are likely skewed due to the greater concentration of experimental PFOA. These preliminary results will allow for the next phases of PFOA research to commence, including confirmation through liquid chromatography/mass spectrometry of low concentrations and developing bioremediation techniques.

Cannabis (Cannabis Sativa L.) is now legally produced in many regions worldwide. Cannabis flourishes under high light intensities (LI); making it an expensive commodity to grow in controlled environments, despite its exceptionally high market value. It is commonly believed that cannabis secondary metabolite levels may be enhanced both by increasing LI and by exposing crops to ultraviolet radiation (UV). However, there is sparse scientific evidence to guide cultivators. Therefore, the impact of LI and UV on yield and quality must be elucidated to enable cultivators to optimize their lighting protocols. We explored the effects of LI, ranging from 350 to 1400 μmol m^-2 s^-1 and supplemental UV spectra on cannabis yield and potency. There were no spectrum effects on inflorescence yield, but harvest index under UVA+UVB was reduced slightly (1.6%) vs. the control. Inflorescence yield increased linearly from 19.4 to 57.4 g/plant and harvest index increased from 0.565 to 0.627, as LI increased from 350 to 1400 μmol m^-2 s^-1. Although there were no UV spectrum effects on total equivalent Δ⁹-tetrahydrocannabinol (T-THC) content in leaves, the neutral form, THC, was 30% higher in UVA+UVB vs. control. While there were no LI effects on inflorescence T-THC content, the content of the acid form (THCA) increased by 20% and total terpenes content decreased by 20% as LI increased from 350 to 1400 μmol m^-2 s^-1. High LI can substantially increase cannabis yield and quality, but we found no commercially-relevant benefits of adding supplemental UV radiation to indoor cannabis production.

Phototherapy is an efficient strategy to respond to oxidative stress and has been in the spotlight in various therapeutic fields through its biological effect, but the exact molecular mechanism has not yet been established. As a result of irradiating RAW264.7 cells with a 630 nm or 850 nm LED with an energy intensity of 0.01J/cm2, cell viability was increased depend on the irradiation time. After H2O2 was added, 630 nm or 850 nm LEDs were irradiated for 10 min or 40 min to increase cell viability by about 1.7- or 1.6-fold, respectively. In addition, 630nm or 850nm LED irradiation showed a significant ROS scavenging effect and significantly reduced TUNEL-positive cells by 45.7% and 37.8%, respectively, compared to cells treated only with H2O2. In the result of flow cytometry, the number of cells in the late apoptosis stage was about 2.3- and 1.8-fold lower than that of the cells treated with H2O2 only, but there was no significance. The Bax/Bcl-2 ratio of cells irradiated with 630 nm or 850 nm LED was significantly lower than that of cells treated with H2O2 only, and the expression of procaspase-3 and cleaved PARP was also significantly expressed in the direction of suppressing cell death. In conclusion, the ROS scavenging activity by 630 nm or 850 nm LED irradiation, leading the expression of cell death pathway proteins in the direction of inhibiting cell death.

We revisit the argument that link the efficiency of a solar cell to its reverse operation as a LED, in the case where the material is organic. In organic cells, exciton transport is an intermediate process between sunlight absorption and the generation of electric current. We show that quenching exciton radiation can be beneficial to cell efficiency, without contradicting the general rule prevailing for semiconductor cells. Our treatment allows us to discuss both bulk heterojunction and planar junctions.

Review of the existing bibliography shows that the direction and magnitude of the long-term trends of UV irradiance, and their main drivers, vary significantly throughout Europe. Analysis of total ozone and spectral UV data recorded at four European stations during 1996 – 2017 reveals that long-term changes in UV are mainly driven by changes in aerosols, cloudiness, and surface albedo, while changes in total ozone play a less significant role. The variability of UV irradiance is large throughout Italy due to the complex topography and large latitudinal extension of the country. Analysis of the spectral UV records of the urban site of Rome, and the alpine site of Aosta reveals that differences between the two sites follow the annual cycle of the differences in cloudiness and surface albedo. Comparisons between the noon UV index measured at the ground at the same stations and the corresponding estimates from the DWD forecast model and OMI/Aura observations reveal differences of up to 6 units between individual measurements, which are likely due to the different spatial resolution of the different datasets, and average differences of 0.5 – 1 unit, possibly related to the use of climatological surface albedo and aerosol optical properties in the retrieval algorithms.

Dunaliella salina is a rich source of 9-cis β-carotene, which has been identified as important in the treatment of retinal dystrophies and other diseases. We previously showed that chlorophyll absorption of red light photons in D. salina is coupled to oxygen reduction and phytoene desaturation and increases the pool size of β-carotene [1]. Here we show for the first time that growth under red light also controls conversion of extant all-trans β-carotene to 9-cis β-carotene by β-carotene isomerases. Cells illuminated with red light from a light emitting diode (LED) during cultivation contained a higher 9-cis β-carotene content compared to cells illuminated with white or blue LED light. The 9-cis/all-trans β-carotene ratio in red light treated cultures reached >2.5:1 within 48 hours and was independent of light intensity. Illumination using red light filters that eliminated blue wavelength light also increased the 9-cis/all-trans β-carotene ratio. With norflurazon, a phytoene desaturase inhibitor which blocked downstream biosynthesis of β-carotene, extant all-trans β-carotene was converted to 9-cis β-carotene during growth with red light and the 9-cis/all-trans β-carotene ratio was ~2:1. With blue light under the same conditions, 9-cis β-carotene was likely destroyed at a greater rate than all-trans β-carotene (9-cis/all-trans ratio 0.5:1). Red light perception by the red light photoreceptor, phytochrome, may increase the pool size of anti-oxidant, specifically 9-cis β-carotene, both by upregulating phytoene synthase to increase the rate of biosynthesis of β-carotene and to reduce the rate of formation of reactive oxygen species (ROS), and by upregulating β-carotene isomerases to convert extant all-trans β-carotene to 9-cis β-carotene.

Air polution level measurement sometime needs tricky instrumentation, costly, and use chemical reagent that could bad impact to environment, it also time consuming for analysis. In other hand, air polution level measurement, include nitrogen dioxide (NO2) needs accuracy, rapid and environment friendly for its analysis and measurement. Differential Optical Absorption Spectroscopy (DOAS) develop as spectrum measurements both UV and visible, transmitted by specific canal using absorption Lambert Beer’s Law principal. On this basic method, NO2 measurement needs light source with 330 – 500 nm wavelength, it is possible to use cheap blue-LED for this measurement. This research intends to calibrate prototype instrumentation for measuring NO2 by DOAS based using Blue-LED (375 nm) passed in continual gas container. NO2 emission simulated in laboratory scale by reacting copper (Cu) with nitric acid (HNO3) result NO2 gas formation. Blue-LED spectrum analysed by compact CCD Spectrometer for its absorbance spectrum, then calibrated with NO2 measurement using USEPA Method 7B standard that is commonly used in testing laboratory as standard method for NO2 measurement. It has good corelation between spectrum absorbance in CCD Spectrometer to USEPA Method 7B with more than 95% linierity. As rapidity of this measurement and shown good accuracy, more development for this method could carry fast, accurate, cheap, also environmentally friendly method for NO2 measurement.

The present study analyzed light emitting diodes (LEDs) as an output load and used a Taylor series to describe the characteristic curve based on the exponential characteristic of voltage and current. A prototype circuit of a flyback LED driver system was established to verify whether the theory is consistent with actual results. This study focused on the exponential relationship of LED voltage and current. Conventional simulations usually used linear models to present LED loads. However, the linear model resulted in considerable error between simulation and actual characteristics. Therefore, this study employed a Taylor series to describe the nonlinear characteristic of an LED load. Through precise calculations with Mathcad computation software, the error was effectively reduced. Moreover, the process clarified the influence of temperature on LEDs, which benefited the characteristic analysis of the entire system. Finally, a realized circuit of 120-W flyback LED drivers was established for conducting theory verification, including theoretic analysis and evaluation of the system design process of the flyback converter. The circuit simulation software SIMPLIS was used to demonstrate the system model, which enabled quick understanding of the system framework established in this study. Regarding LEDs, a commercially available aluminum luminaire was used as the output load. The measured results of the actual circuit and the simulation results were remarkably consistent. For the same system at the same temperature, the error between the simulation and actual results was less than 3%, which proved the reliability of the Taylor series simulation.

Eyes are quintessential complex traits and our understanding of their evolution guides models of trait evolution in general. A long-standing account of eye evolution argues natural selection favors morphological variations that allow increased functionality for sensing light (Darwin 1859; v. Salvini-Plawen and Mayr 1977; Nilsson and Pelger 1994; Nilsson 2013). While certainly true in part, this focus on visual performance does not entirely explain why diffuse photosensitivity persists even after eyes evolve, or why eyes evolved many times, each time using similar building blocks. Here we briefly review a vast literature indicating most genetic components of eyes historically responded to stress caused directly by light, including UV damage of DNA, oxidative stress, and production of aldehydes. We propose light-induced stress had a direct and prominent role in the evolution of eyes by bringing together genes to repair and prevent damage from light-stress, both before and during the evolution of eyes themselves. Stress-repair and stress-prevention genes were perhaps originally deployed as plastic responses to light and/or as beneficial mutations genetically driving expression where light was prominent. These stress-response genes sense, shield, and refract light but only as reactions to ongoing light stress. Once under regulatory-genetic control, they could be expressed before light stress appeared, evolve as a module, and be influenced by natural selection to increase functionality for sensing light, ultimately leading to complex eyes and behaviors. Recognizing the potentially prominent role of stress in eye evolution invites discussions of plasticity and assimilation and provides a hypothesis for why similar genes are repeatedly used in convergent eyes. Broadening the drivers of eye evolution encourages consideration of multi-faceted mechanisms of plasticity/assimilation and mutation/selection for complex novelties and innovations in general.

With the increasing pace of global warming, it is important to understand the role of meteorological factors in influenza virus (IV) epidemics. In this study, we investigated the impact of temperature, UV index, humidity, wind speed, atmospheric pressure, and precipitation on IV activity in Norway, Sweden, Finland, Estonia, Latvia and Lithuania during 2010-2018. Both correlation and machine learning analyses revealed that low temperature and low UV indexes were the most predictive meteorological factors for IV epidemics in the Northern European countries. Our in vitro experiments confirmed that low temperature and UV radiation preserved IV infectivity. Associations between these meteorological factors and IV activity could improve surveillance and promote development of accurate predictive models for future influenza outbreaks in Northern Europe.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

To study the mechanism of light color on a sea urchin (Tripneustes gratilla), blue light (B, λ450nm), yellow light (Y, λ585-590nm), red light (R, λ640nm), green light (G, λ510nm), white light (W, λ400-780nm) and darkness groups (H) were set up in a seawater recirculating aquaculture system. Six different LED light color treatment groups with a photoperiod of 12 L:12 D were tested for 30 d to investigate the effects of different light colors on the feeding, growth and enzyme activities of T. gratilla (142.45±4.36 g). We found that varying LED light colors significantly impacts the feeding, growth, and enzyme activity of T. gratilla. Notably, the sea urchins in group B exhibited better growth with a weight gain rate of 39.26%, while those in group R demonstrated poorer growth with a weight gain rate of only 26%. The feeding differed significantly (P<0.01) between groups B and R, with group B consuming the highest daily intake (6.03±1.69 g) and group R consuming the lowest (4.54±1.26 g). Throughout the three phases, there was no significant change in the viability of the AMS (P>0.05). Conversely, pepsin viability significantly increased (P<0.01) in group B. LPS viability remained consistently at the lowest level, with no notable differences in group W from those observed in group B. In group R, both AMS and pepsin viability remained lower, whereas lipase viability was noticeably higher in each phase compared to group B (P<0.01). Regarding antioxidant enzymes, group R exhibited a trend of initially increasing and then decreasing CAT, SOD, and GSH-PX activities, particularly during the third stage (15-30 d), with a significant decrease observed in antioxidant enzyme activities (P<0.01). The outcomes suggest that blue light positively affects the growth, feeding, digestion, and antioxidant capacity of T. gratilla in comparison to other light environments, whereas the red light has an inhibitory impact.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

Underwater wireless optical communication (UWOC) is acknowledged as a useful way to transmit data in ocean for short distance application. Carrying UWOC device on mobile platform is quite practical in ocean engineering, which is helpful to exploit its advantages. In application, such platform needs camera to observe surroundings and guide its action. Since the majority of ocean is always dark, active illumination is necessary to imaging. Once UWOC worked in such environment, its performance is affected by the illumination light noise. In this paper, we study the influence of underwater LED illumination on bidirectional UWOC with Monte Carlo method. We simulate forward noise from the LED illumination to the opposite receiver in the cooperative terminal, and the backscattering noise on the adjacent receiver in the same terminal. The results show that the forward noise is reduced with the increase of absorption coefficient, scattering coefficient, transmitting distance, and separated distance between receiver and the optical axis of LED. But it becomes greater with FOV of receiver. The backscattering noise is reduced with the increase of absorption coefficient and separated distance between receiver and LED. But it becomes greater with FOV and scattering coefficient, while it has little relation with transmitting distance. In order to reduce such two kind noises, besides inserting optical filter in the receivers and narrow their field, the optical axis of LED light should keep away from the receivers. The results in this paper is helpful for UWOC application.

As the global semiconductor market is growing steadily, the need for optimization of the man-ufacturing process is paramount. For example, in the process of transferring the semiconductor chips to the substrate, each chip needs to be individually separated from the dicing tape via a plunger. In this process, however, the fixed chip is not easily removed from the tape due to strong adhesion, and the chip can become damaged if it is forcibly pulled out. Therefore, the present paper reports the development of functional adhesive tapes that initially adhere strongly to the semi-conductor chip on the dicing tape but can be easily removed after transfer. The fabricated functional tape has an initial adhesion of 350 gf, which enables firm fixing of the semiconductor chip to be transferred, and a final adhesion of 0.8 gf after UV curing, thereby facilitating removal of the chip without damage after transfer. Therefore, the fabricated functional tape is expected to contribute to the optimization of the semiconductor manufacturing process and is expected to be useful in the semiconductor package manufacturing process.

In this study we focus on measurements and modeled UV index at the region of Athens, Greece, during a period of a low ozone event. During the period of 12 to 19 of May 2020, total column ozone (TOC) showed extremely low values 35-55 DU (up to 15%) decrease from the climatic mean (being lower than the -2σ). This condition favors the increase of UV erythemal irradiance, since stratospheric ozone is the most important attenuator at the UVB spectral region. A parallel intrusion of Saharan Dust aerosols in the region has masked a large part of the low ozone effect on UV irradiance. In order to investigate the event, we have used spectral solar irradiance measurements from the Precision Solar Radiometer (PSR), total column ozone from the BREWER spectrophotometer and Radiative Transfer Model (RTM) calculations. Model calculations of UV Index (UVI) showed an increase of ~30% compared to the long term normal UVI due to the low TOC while at the same time and for particular days, aerosols masked this effect by ~20%. The study points out the importance of accurate measurements or forecasts of both ozone and aerosols when deriving UVI under unusual low ozone-high aerosol conditions.

The sunscreen industry is achieving remarkable worldwide prominence by responding to the growing need for skin protection with fast-paced innovation. Increased consumer awareness of the harmful effects of sunlight has fueled the demand for improved photo protection. The need for broad-spectrum protection from both UVA and UVB rays has inspired scientists worldwide to research new cosmetic formulations and delivery systems. More effective sunscreen actives, emollients and novel cosmetic and functional ingredients have been regularly added to the formulator’s repertoire. Creativity in innovation has been hindered only by regulatory agencies and patent restrictions worldwide. Familiarity with the current restrictive regulations and patent law infringements has become integral to any research effort attempting to provide improved protection to individuals affected by the sun’s damaging effects. The increasing incidence of skin cancers and photo damaging effects caused by ultraviolet radiation has increased the use of sun screening agents, which have shown beneficial effects in reducing the symptoms and reoccurrence of these problems. Unlike the situation in Europe where sunscreen ingredients are considered under cosmetics guidelines, the FDA is required to define sunscreens as drugs since they are advertised to prevent sunburn and, more recently, the risk of skin cancer. In the USA, the FDA has been regulating this industry since August 25, 1978, with the publication of the Advance Notice of Proposed Rulemaking. Sunscreens are considered drugs and cosmetics and therefore must be governed by the FDA-OTC monograph. With the variety of sunscreen agents used in cosmetic and UV protection products, Australia, Canada, and the European Union (EU) have also developed regulatory protocols on safe sunscreen product use. Unlike the USA though, Australia has approved 34 active sunscreen ingredients and the EU has approved 28 of these ingredients. Current FDA regulations allow labeling of sunscreen products to a maximum of 30þ, despite the many products currently available with numbers as high as 100. From a cosmetic formulation point of view, increasing the SPF number in a product is governed by simple chemical principles.

Controlling the concentration of free radicals in polymerization systems is advantageous for preparing cationic polyacrylamide (CPAM) with high molecular weight and acceptable dissolvability. In this study, a novel ultraviolet (UV)-initiated system characterized with adjustable light intensity and redox-azo complex initiator was used to synthesize a CPAM flocculant named NP. Comparatively, another CPAM flocculant named SP with stable UV light intensity and single initiator was prepared. The chemical structure, morphology, and thermal stability were analyzed through instrumental analysis. Proton nuclear magnetic resonance indicated that NP was successfully prepared, and a small fraction of cationic homopolymer was mixed in the product. Polymerization conditions were optimized, and polymerization mechanism was determined by investigating the effects of various parameters on intrinsic viscosity, conversion, and dissolvability. Results showed that the best performance was obtained at indexes of 0.45 wt‰ redox initiator concentration, 0.2 wt‰ azo initiator concentration, 40.0 wt% of cationic monomer, first- and second-stage light intensities of 8.5 and 13 mW/cm², respectively, and 3 wt% urea. Sludge conditioning performances of NP and SP were comparatively evaluated, and the mechanism was determined by investigating the sedimentation behavior and floc size distribution. High intrinsic viscosity, porous morphology structure, and the mixed cationic homopolymer of NP resulted in better sludge conditioning performance.

Red color conversion materials have often been used in conventional white LEDs (light-emitting diodes) to enhance the insufficient deep red component and thus improve the color rendering property. Quantum dots (QDs) are one of the candidates due to their flexibility in controlling the emission wavelength, which is attributed to the quantum confinement effect. Two types of remote QD components, i.e., QD films and QD caps, were prepared and applied to conventional white LED illumination to improve the color rendering properties. Thanks to the red component near 630 nm caused by the QD components, the color rendering indices(CRIs) of both Ra and R9 could be increased to over 95. It was found that both the diffusing nature of the reflector and the light recycling process in the vertical cavity between the bottom reflector and the top optical films play important roles in improving the color conversion efficiency of remote QD components. The present study showed that the proper application of remote QDs combined with a suitable optical cavity can control the correlated color temperature of the illumination over a wide range, thus realizing different color appearances of white LED illumination. In addition, a high CRI of over 95 could be achieved due to sufficient excitation from fewer QDs due to the strong optical cavity effect.

This work presented the design and fabrication of blood vessel and breast tumor detection device (BKA-06) based on optical energy spectroscopy. The BKA-06 device uses red-to-near-infrared light-emitting diodes that allow physicians or physicians to visualize blood vessels and surface structures such as breast tumors with the naked eye. The device consisted of built-in current control circuit to have the appropriate brightness (maximum illuminance of 98592 lux) for the examination of superficial tumors deep under the skin, with a scan time of 3-5 minutes. The device BKA-06 could facilely observe each layer of blood vessels at the depth of the skin. For breast tumors, the location, size and invasive areas around the tumor can also be visualized with the naked eye using the BKA-06 sensor. The results show that the BKA-06 sensor can provide clear breast tumor and vascular images with a penetration of up to 15 cm in the skin and tissue layers of the breast. The breast tumor scanning tests with the BKA-06 sensor gave patients quick results and compared them through cell biopsy and MRI respectively. The device has the advantage of being simple, easy to use, providing potential practical applications in the medical field, reducing costs for patients when taking MRI or CT scans. Therefore, the BKA-06 device is expected to help doctors and medical staff overcome difficulties in infusion as well as identify breast tumors to support early breast cancer diagnosis and treatment.

Community-led initiatives have emerged as powerful drivers of change in the realm of local environmental protection. This qualitative study, conducted in Acmac, Iligan City in 2020, delves into the motivations, strategies, challenges, and outcomes of community-led initiatives, shedding light on their transformative potential. Through interviews, participant observations, and document analysis, the study explores the themes of community empowerment, collaborative decision-making, environmental justice, sustainable practices, and policy advocacy. The findings reveal the significance of bottom-up approaches, emphasizing the role of community engagement in achieving environmental sustainability. The study contributes to the literature by filling gaps in understanding and providing insights into the dynamics and effectiveness of community-led initiatives. The implications of the findings extend beyond the local context, highlighting the need for inclusive environmental practices and policy frameworks. By fostering community empowerment and collaborative action, this research sets the stage for future research and the promotion of community-led initiatives worldwide.

Vision is our primary sense as the human eye is the gateway for more than 65% of information reaching the human brain. Today’s increased exposure to different wavelengths and intensities of light from Light Emitting Diodes (LEDs) sources could induce retinal degeneration and accompanying neuronal cell death. Damage induced by chronic phototoxic reactions occurring in the retina accumulates over years and it has been suggested to be responsible for the etiology of many debilitating ocular conditions. In this work, we examined how LED stimulation affects vision by monitoring changes in the expression of death and survival factors as well as microglial activation in LED-induced damage (LID) of the retinal tissue. We found an LED exposure-induced increase in the mRNA levels of major apoptosis-related markers -BAX, Bcl-2, and Caspase-3 and an accompanying wide-spread microglial and Caspase-3 activation. Everyday LED light exposure was accounted for all the described changes in the retinal tissue of mice in this study, indicating that overuse of non-filtered direct LED light can have detrimental effects on the human retina as well.

Patients with heart failure have difficulty in self-care management, as daily monitoring and recognizing symptoms do not readily triggers an action to avoid hospital admissions. The purpose of this study was to understand the impact of a nurse-led complex intervention on symptom recognition and fluid restriction. A latent growth model was designed to estimate self-care management and quality of life changes on patients with heart failure and assessed by a pilot study, for three months, to sixty-three patients (33 control, 30 intervention). Patients in the control group had a higher risk of hospitalisation (IRR 11.36; p<.001) and emergency admission (IRR 4.24; p<.001) at three-months follow-up. Analysis of the time scores demonstrated that the intervention group had a clear improvement in self-care behaviours (βSlope. Assignment_group=-.881; p<.001) and in the quality of life (βSlope. Assignment_group=1.739; p<.001). This study supports that a nurse-led program on symptom recognition and fluid restriction can have a positive impact on self-care behaviours and quality of life in patients with heart failure.

A typical white-light light-emitting diode (LED) can achieve a sunlight-like spectral profile in the visible spectrum by means of using an optical filter, with an inverted transmission profile to the white LED, fabricated using a deposition coating process. The unfiltered white LED generates white light by mixing light emitted by a blue LED (450 nm) with emission from the yellow phosphorescence excited by the blue light and differs significantly from the characteristics of the full-spectrum natural light. In this study, the spectral characteristics of the filtered LED light can be improved to reach a general color rendering index value (Ra) of 95.6 at the D65.

We report on the design, characterization and validation of a spherical irradiation system for inactivating SARS-CoV-2, based on UV-C 275 nm LEDs. The system is designed to maximize ir-radiation intensity and uniformity, and can be used for irradiating a volume of 18 liters. To this aim: (i) several commercially available LEDs have been acquired and analyzed; (ii) a complete optical study has been carried out in order to optimize the efficacy of the system. (iii) The re-sulting prototype has been characterized optically, and tested for the inactivation of SARS-CoV-2 for different exposure times, doses and surface types. Results indicate that a 99.9% inactivation can be reached after 1 minute of treatment with a dose of 83.1 J/m2.

Patients with heart failure have difficulty in self-care management, as daily monitoring and recognizing symptoms do not readily trigger an action to avoid hospital admissions. The purpose of this study was to understand the impact of a nurse-led complex intervention on symptom recognition and fluid restriction. A latent growth model was designed to estimate self-care management and quality of life changes on patients with heart failure and assessed by a pilot study, for three months, to sixty-three patients (33 control, 30 intervention). Patients in the control group had a higher risk of hospitalisation (IRR 11.36; p<.001) and emergency admission (IRR 4.24; p<.001) at three-months follow-up. Analysis of the time scores demonstrated that the intervention group had a clear improvement in self-care behaviours (βSlope. Assign-ment_group=-.881; p<.001) and in the quality of life (βSlope. Assignment_group=1.739; p<.001). This study supports that a nurse-led program on symptom recognition and fluid restriction can have a positive impact on self-care behaviours and quality of life in patients with heart failure.

1) Background: Parents are increasingly fascinated by alternative weaning methods, such as ba-by-led or vegetarian weaning. However, international pediatric societies are still cautious to-wards alternative weaning methods, due to their significant risk of nutritional deficiencies. The aim of this study is to describe the attitude of Italian pediatricians towards unconventional weaning, with particular regard to vegetarian and baby-led. (2) Methods: A 20-question ques-tionnaire was sent to Italian pediatricians, from January to December 2019; (3) Results: Responses were received from 73/1000 (7.3%) pediatricians. The vast majority of surveyed pediatricians (78.1%) is familiar with baby-led and vegetarian weaning, but only 24.7% is in favor of their practice. A significant number of pediatricians (63.0%) received request from parents for an al-ternative weaning regimen. (4) Conclusions: The survey revealed a significant gap between pedi-atricians’ attitude and parental demand concerning unconventional weaning. This could signifi-cantly impair the alliance between parents and pediatricians with the risk to expose infants and children to severe nutritional deficiencies due to self-management by parents with poor surveil-lance from health professionals.

The importance of oxygen in the winemaking process is widely known, as it affects the chemical aspects and therefore the organoleptic characteristics of the final product. Hence, it is evident the usefulness of a continuous and real-time measurements of the levels of oxygen in the various stages of the winemaking process, both for monitoring and for control. The WOW project has focused on the design and the development an innovative device for monitoring the oxygen levels in wine. This system is based on the use of an optical fiber to measure the luminescent lifetime variation of a reference metal/porphyrin complex, which decays in presence of oxygen. The developed technology results in a high sensitivity and low cost sensor head that can be employed for measuring the dissolved oxygen levels at several points inside a wine fermentation or aging tank. This system can be complemented with dynamic modeling techniques to provide predictive behavior of the nutrient evolution in space and time given few sampled measuring points for both process monitoring and control purposes. The experimental validation of the technology has been first performed in a controlled laboratory setup to attain calibration and study sensitivity with respect to different photo-luminescent compounds and alcoholic or non-alcoholic solutions, and then in an actual case study during a measurement campaign at a renown Italian winery.

If the world’s countries seriously tackle the climate targets agreed in Paris, their citizens are likely to experience substantial changes in production, consumption and employment. We present a long-run post-Keynesian model for studying the potential implications of a major transition on macroeconomic stability and employment. It is a demand-led model in which firms have considerable but not absolute freedom to administer prices, while household consumption exhibits inertia. Firms continually seek input-saving technological improvements that, in the aggregate, tie technological progress to firms' cost structure. Together with firm pricing strategies and wage setting, the productivities of different inputs determine the functional income distribution. Saving and investment, and production and purchase of consumption goods, are undertaken by different economic actors, driven by income and capacity utilization, with the possibility that productive capacity exceeds, or falls short of, effective demand. The model produces business cycles and long waves driven by technological change. We present results for a “downshifting” scenario in which households voluntarily withdraw labor and discuss the implications of downshifting for stability, growth, and employment. We contrast the downshifting scenario with ones in which households reduce consumption without withdrawing from the labor pool.

The nature of the blue color in the iodine-starch reaction (or, in most cases, iodine-iodide-starch reaction, i.e. as I2 as well as I- are typically present) has for decades elicited debate. The intensity of the color suggests a clear charge-transfer nature of the band at ~600 nm, and there is consensus regarding the fact that the hydrophobic interior of the amylose helix is the location where iodine binds. Three types of possible sources of charge transfer have been proposed: (1) chains of neutral I2 molecules, (2) chains of poly-iodine anions (complicated by the complex speciation of the I2 - I- mixture), or (3) mixtures of I2 molecules and iodide or polyiodide anions. An extended literature review of the topic is provided here. According to the most recent data, the best candidate for the “blue complex” is a I2-I5-I2 unit – expected to occur in repetitive manner inside the amylose helix.

Skin aging is one of the most common problems facing humanity. It occurs because of altering the balance between free radicals and antioxidants and increasing the amount of the reactive oxygen species (ROS) in skin cells, which leads to oxidative stress especially when exposed to UV radiation. Antioxidants can neutralize the harmful effects of ROS, and secondary plant metabolites can help protect against UV radiation. In this study, punicalagin was extracted from pomegranate and concentrations of total polyphenolics and flavonoids were determined and antioxidant activities measured. Punicalagin was loaded onto niosomes and its morphology and release were studied. An in vitro study was performed on human fibroblast cell line HFB4 cells with aging induced by H2O2 and UV radiation. Cell cycle arrest was studied and different genes (MMP3, Col1A1, Timp3, and TERT) involved in the skin aging process were selected to measure punicalagin's effect. Punicalagin succeeded in reducing the growth arrest of HFB4 cells, activated production of the Col1A1 and Timp3 genes, maintained collagen level, and lowered of MMP3. Punicalagin increased human TERT concentration in skin cells. Punicalagin is promising as a natural antioxidant to protect human skin from aging.

ATLID (ATmospheric LIDar) is the atmospheric backscatter LIDAR (Light Detection and Ranging) on board of the EarthCARE (Earth Cloud, Aerosol and Radiation Explorer) mission, the sixth Earth Explorer Mission of the ESA (European Space Agency) Living Planet Programme [1-5]. ATLID’s purpose is to provide vertical profiles of optically thin cloud and aerosol layers, as well as the altitude of cloud boundaries [6-10]. In order to achieve this objective ATLID emits short duration laser pulses in the UV, at a repetition rate of 51 Hz, while pointing in a near nadir direction along track of the satellite trajectory. The atmospheric backscatter signal is then collected by its 620 mm aperture telescope, filtered through the optics of the instrument focal plane assembly, in order to separate and measure the atmospheric Mie and Rayleigh scattering signals. With the completion of the full instrument assembly in 2019, ATLID has been subjected to an ambient performance test campaign, followed by a successful environmental qualification test campaign, including performance calibration and characterization in thermal vacuum conditions. In this paper the design and operational principle of ATLID is recalled and the major performance test results are presented, addressing the main key receiver and emitter characteristics. Finally, the estimated instrument, in-orbit, flight predictions are presented; these indicate compliance of the ALTID instrument performance against its specification and that it will meet its mission science objectives for the EarthCARE mission, to be launched in 2023.

Adenoviruses (Ads) have been extensively manipulated for the development of cancer selective replication, leading to cancer cell death or oncolysis. Clinical studies using E1-modified oncolytic Ads have shown that this therapeutic platform was safe, but with limited efficacy, indicating the necessity of targeting other viral genes for manipulation. To improve the therapeutic efficacy of oncolytic Ads, we treated the entire Ad genome repeatedly with UV-light and have isolated AdUV which efficiently lyses cancer cells as reported previously [1]. In this report, we show that no mutations were observed in the early genes (E1 or E4) of AdUV while several mutations were observed within the Ad late genes which have structural or viral DNA packaging functions. This study also reported the increased release of AdUV from cancer cells. In this study, we found that AdUV inhibits tumor growth following intratumoral injection. These results indicate the potentially significant role of the viral late genes, in particular the DNA packaging genes, to enhance Ad oncolysis.

The full impact of COVID-19 on policing, crime and disorder is slowly being fully unraveled. However, there remains a number of areas of policing that are yet to be examined in detail. Two of these areas include the impact on the intrinsically linked, volume of police recorded intelligence reports, and the use of stop and search. In this study we examine them symbiotically and frame them in the context of the intelligence led policing model, in particular in an effort to understand how national lockdowns in the United Kingdom affected both proactive policing approaches and the underpinning intelligence cycle. To achieve this, we use data from freedom of information requests regarding the annual levels of recorded police intelligence over a 10-year period for 20 police services. To supplement this, we examine overall national monthly volumes of stop and search activity over a 5-year period. Finally, we then use a case study approach of 3 police services to further explore changes in the conduct of stop and search such as the officer defined ethnicity, grounds for search and disposal outcomes. The findings indicate that both recorded intelligence reports and stop and search increased dramatically during periods of lockdown, despite widespread decreases in crime and social mobility. Changes in proportional impact are identified for White and Black citizens, searches for controlled drugs and the no further action disposal, but these are not consistent across police services. Potential causes and implications are then discussed and again, framed within the context of the impact on the intelligence led policing model and wider policing environment.

Recently, light traps using light-emitting diode (LED) lights have been applied to monitor or control insect pests. The oriental armyworm, Mythimna separata Walker, is an important insect pest that has caused damage to several cereal crops, including corn, wheat and rice. The present study aims to seek out a sensitive wavelength causing high phototactic response in M. separata. The study evaluated the phototactic responses of M. separata moths to several LED lights of different wavelengths and luminance intensities under laboratory condition. Results showed that green (520 nm) LED light resulted in significant phototactic response of M. separata moths compared to LED lights of other wavelengths. Additionally, the highest attraction rate of the moths to green LED light appeared in luminance intensity group of 200 lux compared to the other intensities groups. Experiments under optimum conditions based on the above experiments revealed that the green LED light exhibited the strongest attraction rate (64.44%) among all experimental groups. An experiment performed in a net cage also showed that green LED light resulted in the highest phototactic response of M. separata moths, 1.7 times more than a commercial black light used as control. These findings clearly demonstrate that M. separata moths have a high sensitivity to the green LED light. Therefore, a light trap equipped with green LED light could be useful for monitoring and controlling M. separata moths.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

The photodegradation of azithromycin present was carried out in water using H2O2 under UV irradiation. The reaction variables considered in this study were the amount of H2O2 solution and the initial concentration of azithromycin to evaluate the performance of the photodegradation process. The azithromycin degradation was not observed in the dark during stirring for 20 minutes. The study showed efficient photodegradation of azithromycin using H2O2 as an oxidant in the presence of UV irradiation. The azithromycin degradation was affected significantly by the pH of the irradiated solution. The degradation was low at an acidic pH and showed an increasing trend as the pH changed to basic. The azithromycin degradation was increased with a higher amount (higher concentration) of H2O2. The degradation of azithromycin decreased with a higher concentration of azithromycin in the reacting solution. The highest degradation of AZT was achieved in 1 hour using a 1.0 ppm AZT solution containing 3 ml of H2O2. The experimental data obtained was well-fitted to zero-order reaction kinetics. The results of this study were found to be superior when compared with those reported in the literature, with photocatalysis using nanomaterials and photolysis using irradiation and H2O2. The UV/H2O2 system was found to be quite efficient for the photodegradation of azithromycin, and this system can be applied to degrade other organic pollutants present in industrial wastewater. To this point, such a study has not been reported specifically for AZT photodegradation.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

The spectrophotometric methods of determination of the active pharmaceutical ingredients meloxicam and nimesulide were reviewed, and a simple UV-spectrophotometric method for the determination of these active pharmaceutical ingredients in industrial equipment cleaning validation samples were proposed. The methods are based on extraction of the residual quantities of meloxicam and numesulide from the manufacturing equipment surface by the concentrated sodium carbonate solution, and the subsequent UV-spectrophotometric determination of the basic forms of the drugs at the wavelength of 362 nm for meloxicam and at 397 nm for nimesulide. The calibration graphs are linear in the range from 5 to 25 mg/L of both nimesulide and meloxicam, the molar attenuation coefficients are 6100 m2/mol for nimesulide and 9100 m2/mol for meloxicam, the limit of detection is 0.8 mg/L for nimesulide and 1.9 mg/L for meloxicam, the limit of quantification is 2.5 mg/L for nimesulide and 5.8 mg/L for meloxicam, the methods are selective with respect to the common excipients, show a good accuracy (the relative uncertainty does not exceed 4%) and precision (the relative standard deviation does not exceed 5%), do not require lengthy sample preparation and sophisticated laboratory equipment and are suitable for the routine analysis of cleaning validation samples.

The aim of this study, for determination of verteporfin in real samples (simulated body fluid, and simulated tears, 0.9% isotonic sodium chloride solution, Lactated Ringer IV solution for infusion, 5% dextrose IV solution for infusion, lemon juice and drinking water) was the method validation and to examined by HPLC-DAD-UV. Metod validation parameters such as specificity, linearity, precision, accuracy, robustness, limit of detection (LOD) and limit of quantitation (LOQ) for verteporfin were validated and developed according to the International Conference on Harmonization (ICH) Q2 R1 guidelines. The LOD and LOQ for verteporfin were found 0.06 µg/L and 0.2 µg/L, respectively. The recovery values of the optimization and validation for verteporfin were found in the range of 97.5-100.7%. The relative standard deviations (RSD) for vertepofin were <1%. The developed method was successfully applied to real samples with high accuracy and the recoveries (%) from real samples were 99.9, 100, 98.2, 99.2, 99.4, 98.8 and 99.4, respectively.

Evidence has shown that the state of the patient care environment has a direct impact in heightening the risks of hospital acquired infections among patients admitted in hospitals. And in view of the sub-optimal standard of cleanings by housekeeping staff, the quest for a better approach to reliably disinfect environmental surfaces in healthcare facilities. The ultraviolet light has been known for its antimicrobial property, and have been used in water treatment, food processing and in-duct cleaning of ventilations. A recent introduction of its use for surface decontamination has raised interest among hospitals.However, studies have shown that, in spite of its relative success in other applications, there is doubt in its efficacy in decontaminating shadowed areas of the room, and therefore, would not be seen as justifying its capital intensiveness.

Ultraviolet (UV) light with a wavelength of 254 nm has proven to be effective at inactivating microorganisms, and thus has been increasingly employed as a method of disinfection for indoor environments. Solar UV wavelengths (300 to 400 nm) are known to initiate the formation of secondary organic aerosol (SOA) particles from photo-oxidation of volatile organic compounds in the atmosphere, but germicidal wavelengths have not been extensively studied for indoor environments. In this work, toluene was exposed to 254 nm UV light in a laboratory photoreactor, with varying conditions of the air, the duration of UV exposure, and the duration of post-UV time. The number of particles formed in the fine particulate matter (PM2.5) size range was measured, and significant levels of particle formation were observed for UV exposure periods of as short as 5 minutes. The particle formation ranged from 2.4x10⁶ particles/m³ for 5 minutes of UV exposure, to 1449.8x10⁶ particles/m³ for 15 minutes of UV exposure. Particle formation was found to increase with increasing concentrations of gas phase toluene, and at relative humidity of approximately 20% and higher. Variations in the initial number of particles present did not appear to have a significant effect on the particle formation, suggesting that nucleation was not a controlling factor. However, tests in a commercial environment showed no significant detectable PM2.5 formation, indicating that SOA formation during the intermittent use of germicidal UV may not significantly affect indoor air quality.

The analysis of the current safety standards for electric toys showed that the normative intensity limits for visible light emitted by LEDs integrated in toys are overestimated. These limits were originally set in a scientific article published in 2012 that was adapted into the international safety standard published in 2017, and into the subsequent European and national standards, all published in 2020. The overestimation of the intensity limits results from several errors made in the original article. Accordingly, the current normative intensity limits for visible light used in toys do not protect the children’s eyes against adverse effects of exposure to high intensity LEDs which may compromise their visual health. Updating the safety standards for electric toys using a method based on robust scientific data is recommended to protect children's visual health and ensure their long-term well-being.

This article investigates if public investments in rural basic infrastructure represent the best strategy for boosting the local economy of rural communities from Romania. The article focuses on one specific program implemented under the Cohesion policy in the framework of the National Plan for Rural Development called Measure 322. Geographically, the research included a sample of rural communes from the North-Western Region of Romania. Moreover, the study also looks at other determinants of local economic development (LED) than infrastructure investments, with a focus on certain feature characterizing Romanian rural communities such as population size, isolation from urban centers, connection with European and national roads networks, educational stock, etc. The research included three steps, namely the construction of the LED Index, a cvasi-experimental research, and a regression model. Our main findings seem to suggest that while investments in infrastructure help the development gap between beneficiaries and non-beneficiaries remains relatively the same. In terms of determinants of LED, percentage of population with a university degree and connection to a European road are the most significant in the Romanian rural context.

The manuscript presents the optical properties of directly deposited films of gold nanoparticles (AuNPs) prepared by ultrasonic spray pyrolysis technology. Four samples were produced, with an AuNPs deposition time of 15 min, 30 min, 1h and 4h on the glass substrate. The morphological characterization of the deposited films showed that the size of the first deposited AuNPs is between 10 and 20 nm, while with a longer duration of the deposition process, larger clusters of AuNPs grow by coalescence and aggregation. The prepared layers were optically characterised with Ultraviolet–visible spectroscopy (UV-vis) and ellipsometry. The ellipsometric measurements showed an increasingly denser and thicker effective thickness of the AuNPs layers. The extinction spectra display a clear local surface plasmonic resonance (LSPR) signature (peak 520-540 nm), indicating the presence of isolated particles in all samples. For all AuNPs layers, the imaginary part of both ε// and ε⏊ is dominated by a central peak around 2.2 eV corresponding to the LSPR of isolated particles and a high-energy shoulder due to Au interband transitions. It is shown that, as the density of particles increases, the extinction cross section grows over the whole spectral range where measurements are taken. Thus response can be explained with an enhanced electromagnetic response among AuNPs, that can be connected to the increase of particle density but also by the formation of clusters and irregular structures.

Highly transparent, conductive nanosheets are extremely attractive for advanced optoelectronic applications. Previously, we have demonstrated that transparent, conductive Au nanosheets can be prepared by UV irradiation of Au nanoparticle (AuNP) monolayers spread on water, which serves as the subphase. In this study, we show that this UV irradiation technique can easily be extended as a nanosheet modification method by using subphases containing metal ions. That is, aqueous solutions containing Au and Ag ions are effective in modifying Au nanosheets. HAuCl4 solutions increased Au nanosheet thickness, which improved conductivity, but reduced transparency. On the other hand, use of aqueous AgNO3 and CH3COOAg solutions yielded Au-Ag hybrid nanosheets; however, their morphologies depended on the electrolytes used. Homogeneous Au-Ag nanosheets from AgNO3 and AuNPs covered with an Ag nanosheet from CH3COOAg were also produced. Further, these Au-Ag hybrid nanosheets had high conductivity without reduced transparency. Therefore, this UV irradiation method, modified by adding metal ions is quite effective at improving and diversifying properties of Au nanosheets.

Sunscreens are topical preparations containing one or more compounds that protect humans from ultraviolet (UV) light. This review focuses on analytical methods, particularly liquid chromatography, aimed at identifying and determining UV filters (UVFs) in environmental and marine biota matrices. A literature review was done using NIH (PubMed and Medline), FDA and EPA databases, Google Scholar, and Federal Regulations. This retrospective literature review is focused on the last five years. UVFs quantification in environmental and biological matrices showed a wide array of methods where liquid chromatography is predominant. The scientific literature identified a large variety of analytical methodologies that are compared in this review, to evaluate the better results in terms of limits of quantification and the possibility to identify as many analytes as possible simultaneously.

Bixa orellana dye was extracted from the seed by method of Soxhlet extraction using ethanol and a percentage yield of 4.3 was obtained. Recrystallisation of the dye was performed using chloroform and ethanol. TLC was used to separate the dye into Bixin and Norbixin with R_f values of 0.56 and 0.42 respectively. The extracted dye was pH sensitive, insoluble in water but soluble in some organic solvents like ethanol and acetic acid . Characterisation by UV-spectroscopy showed maximum absorption for Bixin and Norbixin at 457nm and 453nm respectively. FTIR spectrum of Bixin and Norbixin showed bands confirming similar functional groups for both Bixin and Norbixin except for –CO- stretching and methylene vibration which was absent in Norbixin.

This review emphasizes the significance of dietary carotenoids in promoting skin health and appearance. The applications of carotenoids in health-promoting and nutrient products and their potential health effects are discussed. Food technology, health, nutrition, dermatology, and dermoaesthetics have recently focused on colorless carotenoids, particularly phytoene, and phytofluene, which have the unique ability to absorb UV radiation. These carotenoids, being significant components of the human diet, are readily bioavailable and have demonstrated various health-promoting actions in re-cent studies. Their distinct structures and properties, such as light absorption, oxidation sensitivity, stiffness, aggregation tendency, and even fluorescence in the case of phytof-luene, contribute to their potential benefits. Furthermore, it is recommended to assess the levels of these carotenoids to evaluate skin carotenoid status accurately.

Lichens are unique extremophilic organisms due to their phenomenal resistance to adverse environmental factors, including ultraviolet (UV) irradiation. Melanization plays a special role in the protection of lichens from UV-B stress. In present study, we analyzed the binding of melanins with the components of cell walls of mycobiont of upper cortex in the melanized lichen thalli Lobaria pulmonaria. Using scanning electron and atomic force microscopy, the morphological and nanomechanical characteristics of melanized layer of mycobiont cells were visualized. Melanization of lichen thalli led to the smoothing the surface relief and thickening mycobiont cell walls and resulted in the increase of deformation values and reduction of adhesion properties of lichen thallus. Treatment of thalli with hydrolytic enzymes, especially chitinase and lichenase, enhanced the yield of melanin from melanized thalli and release of carbohydrates, while treatment with pectinase increased the release of carbohydrates and phenols. Our results suggest that melanin by firmly binding with hyphal cell wall carbohydrates, particularly chitin and 1,4-β-glucans, can form associations, strengthen the melanized upper cortex of lichen thalli, and thereby can contribute to lichen survival under UV stress.

Three octahedral iron(III) nitrate complexes with dimethylated urea ligand isomers, [hexakis(N,N’-dimethylurea-O)iron(III)] nitrate (compound 1), trans-[diaquatetrakis(N,N-dimethylurea-O)iron(III)] nitrate (compound 2) and [hexakis(N,N-dimethylurea-O)iron(III)] nitrate trihydrate (compound 3) were prepared and characterized with single crystal X-ray diffraction, IR, Raman and UV-VIS methods. In compounds 1 and 3, six dimethylurea ligands coordinate to the central FeIII ion via the oxygen in octahedral geometry and the ligands are arranged in a propeller-like manner, dividing the complex cations into two sides. In compound 1, the dimethylurea propellers screw in the opposite direction on the two sides of the complex and in compound 3, they are arranged with the same handedness on the two sides. The complexes have helical chirality. The two sides of the complex cations differ not only in the rotation direction of the ligands but also in the hydrogen bond formation. On one side of the complex cation, the ligands form intermolecular hydrogen bonds only with the crystal waters, meanwhile on the other side of the complex, the ligands form hydrogen bonds only with the nitrate ions. In compound 2, [Fe(N,N-dimethylurea)4(H2O)2]3+ cations form layers that are separated by interconnected NO3- ions forming a hydrogen bonding system and connecting the complex cations A-s and B-s. The three crystallographically different nitrate ions each form four hydrogen bonds in a way that they have one bidentate O atom and two monodentate O atoms, however, the anions differ in their hydrogen bonding. The spectroscopic characteristics of compound 2 were determined by IR measurements on the deuterated compound 2 as well.

An HPLC method for indicating stability was developed, created, and confirmed for the quantification measurement of recombinant human erythropoietin in large quantities as well as dosage forms. An isocratic separation was accomplished using a Thermo Biobasic C18 (250 mm 4.6 mm i.d., 300Ao, 5 m) column with a flow rate of 1.0 mL min-1 as well as a UV detector to monitor the eluate at 278 nm. Acetonitrile, 0.05 mM potassium dihydrogen phosphate (80:20 v/v), and orthophosphoric acid adjusted to 4.0 made up the mobile phase. The drug was exposed to oxidative stress, hydrolysis, and photodegradation to simulate stress conditionsRecombinant Human Erythropoietin, the parent compound, was eluted at roughly 6.675 minutes, as well as all byproducts have been entirely disconnected inside an overall analytical run time of about 15 minutes. To identify quantification limits of 0.05 and 0.2 g mL-1, respectively, the method was linear over a concentration range of 1-6 g mL-1 (r = 0.9989). Recombinant Human Erythropoietin can be measured accurately, selectively, sensitively, and precisely using this method both in dosage form and in bulk. Stress-induced degradation products did not interact with the identification of Recombinant Human Erythropoietin, indicating that the assay is stable.

To investigate the photosynthetic change characteristics of mango leaves under enhanced UV-B radiation, adult ‘Tainong No. 1’ mango (Mangifera indica) trees were treated (N=nine individuals) with simulated enhanced UV-B radiation [24 and 96 kJ/(m2·d)] in the field, and the photochemical reactions, activities of key enzymes in carbon assimilation, and the expression of genes were observed. The results showed that compared with the control, there was a decrease in tree yield and nutritional flavor quality of the fruits under the 96 kJ/(m2·d) treatment, while no significant changes were observed under 24 kJ/(m2·d). After 20 or 40 days, leaves’ net photosynthetic rate (Pn), stomatal conductance (Sc), transpiration rate (Tr), intercellular CO2 concentration (Ci), and chlorophyll a/b under exposure to 96 kJ/(m2·d) of UV-B were significantly lower than in the control, whereas chlorophyll a, chlorophyll b, carotenoids, Hill reaction activity, photochemical quenching coefficient (qP), and Rubisco activities were significantly higher. By contrast, the Hill activity and Rubisco activity under 24 kJ/(m2·d) were significantly higher than the control, while Pn, Sc, Tr, Ci, and the content of photosynthetic pigments were similar to the control. The expression of gene coding the Rubisco big subunit (rbcL) was inhibited by the 96 kJ/(m2·d) treatment. We conclude that stomatal limitation was directly induced by 96 kJ/(m2·d), resulting in the inhibition of photosynthesis and the reduction in yield and deterioration of the quality of mango.

Drug abuse is a major issue worldwide. Methylphenidate (MPH) and alprazolam (ALZ) are commonly prescribed drugs for the treatment of ADHD and anxiety disorders, respectively. The limited studies suggest that abusers primarily use benzodiazepines to counteract adverse effects associated with methylphenidate usage. The main aim of this study was to investigate the interaction of drugs with DNA using spectroscopic methods. Female Wistar rats were administered with MPH (10, 20, 40 mg/kg) and ALZ (5, 10, 20 mg/kg) alone and in combination for a period of 28 days. The FT-IR and UV results reveal some spectral changes in a dose-dependent manner, which indicates interactions of drugs with DNA. Thus, the changes in spectral peaks provide some insight into the mechanism of the interaction of drugs with DNA.

In recent years, the nanoparticles applications have been well recognized in various fields. It is known that nanoparticles as an active ingredient in sunscreens are widely used. Zinc oxide and titanium oxide nanoparticles are common nanoparticles utilized in sunscreens. In this study, we aimed to suggest new nanoparticles for this purpose. Cerium oxide nanoparticles (CeO2-NPs) were synthesized by using Musa sapientum fruit peel extract. Synthesized nanoparticles were identified through Raman, Powder X-ray Diffraction (PXRD), Fourier Transform Infrared spectroscopy (FT-IR), Field Energy Scanning Electron Microscopy (FESEM) and Energy-Dispersive Spectroscopy (EDX). The results showed that size of synthesized nanoparticles are in range 4-13 nm. The cytotoxic activity of synthesized nanoparticles on lung (A549) cancer cell line was performed through MTT assay. The results showed that synthesized nanoparticles are non-toxicity against A549 cell line to below 500 μg/mL of nanoparticles concentration. The Sun protection factor (SPF) was estimated ~ 40 for synthesized CeO2-NPs. So, synthesized nanoparticles can be a good option for use in the cosmetics industry.

The search for molecular biosignatures at the surface of Mars is complicated by an intense irradiation in the mid- and near- ultraviolet (UV) spectral range for several reasons: (i) many astrobiologically relevant molecules are electronically excited by efficient absorption of UV radiation and rapidly undergo photochemical reactions; (ii) even though the penetration depth of UV radiation is limited, aeolian erosion continually exposes fresh material to radiation; and (iii) UV irradiation generates strong oxidants such as perchlorates that can penetrate deep into soils and cause subsurface oxidative degradation of organics.As a consequence, it is crucial to investigate the effects of UV radiation on organic molecules embedded in mineral matrices mimicking the martian soil, in order to validate hypotheses about the nature of the organic compounds detected so far at the surface of Mars by the Curiosity rover, as well as organics that will be possibly found by the next rover missions Mars 2020 and ExoMars 2020. In addition, studying the alteration of possible molecular biosignatures in the martian environment will help to redefine the molecular targets for life detection missions and devise suitable detection methods.Here we report the results of mid-UV irradiation experiments of Mars soil analog samples obtained adsorbing relevant organic molecules on a clay mineral that is quite common on Mars, i.e. montmorillonite, doped with 1 wt% of magnesium perchlorate. Specifically, we chose to investigate the photostability of a plausible precursor of the chlorohydrocarbons detected on Mars by the Curiosity rover, namely phthalic acid, along with the biomarkers of extant life L-phenylalanine and L-glutamic acid, which are proteomic amino acids, and adenosine 5’-monophosphate, which is a nucleic acid component.We monitored the degradation of these molecules adsorbed on montmorillonite through in situ spectroscopic analysis, investigating the reflectance properties of the samples in the Near InfraRed (NIR) spectral region. Such spectroscopic characterization of molecular alteration products provides support for two upcoming robotic missions to Mars that will employ NIR spectroscopy to look for molecular biosignatures, through the instruments SuperCam on board Mars 2020, ISEM, Ma_Miss and MicrOmega on board ExoMars 2020.

Cyanobacterial mass developments in eutrophic ponds and lakes are a major concern for lake management, as many cyanobacteria produce a huge variety of toxic secondary metabolites, e.g. microcystins. The aim of this research was to culture a strain of the cyanobacterium Microcystis sp strain BM25, to observe its biomass production and to isolate and purify protease inhibitors from this cyanobacterial biomass. Different secondary metabolites were isolated following a standard bioassay-guideline. Isolation was performed, with an enzymatic protease assay as bioassay. High performance liquid chromatography was used to identify different fractions of secondary metabolite from the strain BM25. Moreover, protease homogenates were isolated from Daphnia magna in order to test the inhibitors against naturally occurring major digestive proteases trypsin and chymotrypsin. It was measured that 60% MeOH and the 80% MeOH C18-SPE fraction inhibits chymotrypsin activity 98% (6 nmol pNA min^-1 mg^-1) and 99 % (4 nmol pNA min^-1 mg^-1), respectively. In contrast, trypsin activity was not inhibited by methanolic extracts of this cyanobacterium strain.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

The effective treatment for chronic wounds constitute one of the most common worldwide health care problem due to the presence of high levels of proteases, free radicals and exudates in the wound, which constantly activate the inflammatory system avoiding the tissue regeneration. In this study, we describe a multifunctional bioactive and resorbable membrane with in-built antioxidant agent for the continuous quenching of free radicals as well as to control inflammatory response helping to promote the wound healing process. To reach that goal synthesized statistical copolymers of N-vinylcaprolactam (V) and 2-hydroxyethyl methacrylate (H) have been conjugated with catechol bearing hydrocaffeic acid (HCA) molecules. The natural polyphenol (catechol) is the key molecule responsible for the mechanism of adhesion of mussels, and provides the functionalized polymer conjugate a continuous antioxidant response, antiinflammatory effect, UV screen and bioadhesion in the moist environment of the human body, all of them key features in the wound healing process. Therefore, these novel mussel-inspired materials have an enormous potential of application and can act very positively, favoring and promoting the healing effect in chronic wounds.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

This paper provides an overview of current literature on community-led development initiatives in urban contexts, their role in addressing urban inequality, and the challenges they face. This study examines effective strategies of community-led initiatives, such as empowering communities, building partnerships, mobilizing resources, focusing on local needs, and participatory design methods. Case studies from around the world demonstrate how successful community-led development initiatives have been able to overcome obstacles to create more inclusive and equitable urban environments. Institutional support, including technical assistance, capacity building, and regulatory frameworks, are crucial for promoting the success and sustainability of these initiatives. Challenges to community-led initiatives include limited resources, capacity building needs, inadequate infrastructure, lack of institutional support, and lack of trust among community members. Therefore, the paper suggests that it is essential to address these challenges to enable the success of community-led development initiatives. Furthermore, this study recommends that future research should explore how emerging technologies and innovative approaches can effectively support community-led development initiatives and advance more just and sustainable urban development.

Seaweeds have been the target of much attention due to the known bioactivities of some of their compounds. Although many studies about the application of seaweeds in various areas are available, these data are mostly about the raw extracts and not about specific compounds, such as seaweeds pigments. Moreover, the fungal infections of the skin, nails and hair caused by dermatophytes, are the most common fungal infections in humans. These pathologies require long periods of topical and/or systemic treatment that are associated with adverse effects and contraindications. This study had two objectives, the first was to evaluate the possibility of isolating and characterizing the pigments of Calliblepharis jubata and Fucus vesiculosus; the second was to assess their antifungal activity. The extraction of pigments was performed using a method of extraction by exhaustion; the purification was carried out by column chromatography. Three techniques were used to characterize the pigments, thin layer chromatography (TLC), UV-visible spectrophotometry and Fourier-transform infrared spectroscopy (FTIR). The antifungal activity was evaluated using the micro-dilution method, following the EUCAST international standards, on three dermatophytes, Trichophyton rubrum, Trichophyton mentagrophytes and Microsporum canis. It was possible to observe that the extract obtained from the seaweed C. jubata and F. vesiculosus, corresponding to the purified pigment phycobiliprotein, and the crude extract, an enriched extract, obtained from the seaweed C. jubata showed antifungal activity against the three fungal agents of human skin infection.

This study aimed to investigate the atherogenicity (quality) of LDL particles in patients with acute and recovered from COVID-19 infection. The participants were adults, aged 18 years or older of both sexes. Those with positive RT-PCR results at baseline were included in the Acute COVID-19 group (n=33), and those with negative RT-PCR six months after acute infection, were included in the Recovered COVID-19 group (n=30). The LDL quality was evaluated using three validated methods: Z-scan, UV-visible spectroscopy, and Lipoprint. The Recovered COVID-19 group showed significantly higher numbers of large LDL particles (less atherogenic) than the Acute COVID-19 group (P&lt;0.05). We also found that COVID-19 infection was associated with the oxidative modification of LDL particles. D-dimer and CRP levels were correlated with Z-scan results and antioxidant-amount estimate. Moreover, we noticed that the infection left a sequel in LDL quality, even after six months of recovery. These findings highlight the importance of monitoring lipids during and after recovery from COVID-19 infection, and their potential deleterious effect on the LDL profile might correlate with the progression of atherosclerosis and poor clinical outcomes.

The emergence of Non-Ionizing Radiation (NIR) has stimulated the growth and advancement of technological civilization. NIR is ubiquitous; it has helped improve all fields and even deepened democratic processes through the transfer of data and electronic transmission of results etc. A breathtaking part of NIR is its recent application in the treatment of adverse health effects through radiofrequency ablation, phototherapy, etc. as summarized in Table 1. The benefits of NIR are enormous, however, technological civilization has not come without a cost; some of the adverse health effects associated with NIR include skin cancers, sleep disorders, photo-aging, etc. as summarized in Table 2. Therefore, with the rapid and sporadic increase in the sources of NIR from Natural and Artificial sources including fossil fuel burning, Starlink technology, mobile phones, mobile base antennas, etc., background radiation is expected to rise beyond the exposure limit leading to health illnesses. Intrinsically, there is a dare need to marry concerns that evolve with this growth. Hence, this review article aims to congregate the health hazards associated with NIR and the state-of-the-art applications of NIR in medicine and the health sector in Nigeria being a developing country. Part of our recommendations is that the government at all levels should set up enforcement agencies and policies to drive strict adherence to NIR as provided by ICNIRP; frequent-periodic assessments of background radiation in public places should be carried out due to the increasing sources. In addition, further research is needed to ascertain the health hazard from emerging sources of NIR like Starlink technology and to substantiate findings of non-thermal effects.

The Ramazzottius varieornatus tardigrade is an extremotolerant terrestrial invertebrate belonging to the phylum of Tardigrada. At a length of 0.1-1.0 mm, tardigrades are small animals with an exceptional tolerance to extreme conditions such as high pressure, chemicals and irradia-tion. These properties have been attributed to the recently-discovered Dsup protein. Dsup is a nucleosome-binding protein that prevents DNA damage against X-ray and oxidative stress without impairing cell life, also in Dsup-transfected animal and plant cells. However, the precise “protective” role of this protein is still under study. We performed experiments on human cells and shows that, as compared to control cells, Dsup+ cells are more resistant to UV-C exposure and H2O2. Real-time PCR identified different expression patterns of endogenous genes involved in apoptosis, cell survival and DNA damage repair in Dsup+ cells in response to H2O2 and UV-C. While H2O2 treatment in Dsup+ cells only marginally involved the activation of pathways responsible for DNA repair reinforcing the idea of a direct protective effect of the protein on DNA, in UV-C exposed cells, Dsup efficiently upregulates DNA damage repair genes. In conclusion, our data may help to delineate the different mechanisms by which the Dsup protein operates in response to different insults.

UV-Visible spectroscopy method has been developed for the analysis of Thiamine in biological and pharmaceutical product, based on a chromogenic derivatizing reaction using PDAB (P- dimethyl amino benzaldehyde) reagent. A Central Composite Design (CCD) design with response surface methodology was executed for optimization of experimental conditions of drug with a smaller number of experimental trials. Three independent factors, the concentration of PDAB, the volume of PDAB reagent, and volume of HCl, were used to construct a mathematical model and study the effects of these independent factors on responses as absorbance. The colored complex exhibits a Red shift with absorption maximum λmax at 425 nm, which was selected as the analytical wavelength. The drug seems to be linear, which was established via the regression analysis from 5-30 μgmL-1, with an R2 value of 0.998.The % RSD for intraday and interday precision was < 2%, with good recovery ranging from 95.02 to 101.43% with biological and pharmaceutical samples. LOD and LOQ of the developed method were found to be 1.51 μg mL-1 and 4.57 μg mL-1.This method can be used in routine analysis of pharmaceutical products containing aromatic primary amines along with an estimation of biological samples like urine, blood, sweat, faeces.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

The high-power Asymmetric half-bridge Converter (AHBC) LED constant current driver controlled by digital current mode is a fourth-order system. Static operating point, parasitic resistance, load characteristics, sampling effect, modulation mode and loop delay will have great influence on its dynamic performance. In this paper, the small-signal pulse transfer function of the driver is established by the discrete-time modeling method for the two operating points corresponding to the three modulation modes of the trailing edge, leading edge and double edge. And, the effects of parasitic parameters, delay effect, sampling effect and load effect are fully considered in modeling. For a large number of complex exponential matrix operations, the first order Taylor formula is used for approximate calculation after the coefficient matrix is obtained by substituting the data. Then, Matlab software is used to compare and analyze the discrete-time model and the discrete-average model. The results show that the proposed discrete-time model can more accurately characterize the resonant peak and high-frequency dynamic characteristics, and is very suitable for the design of high frequency digital controller.

The advancement of the pediatric traumatic brain injury (TBI) knowledge base requires biospecimens and data from large samples. This study seeks to describe a novel clinical research modality to establish best practices for enrolling a diverse pediatric TBI population and quantifying key information on enrollment into biobanks. Screening form responses were standardized and cleaned through Google Sheets. Data was used to analyze total individuals at each enrollment stage. R was utilized for final analysis, including chi-square goodness of fit and proportion statistical tests, to determine further significance and relationships. Issues throughout data cleaning shed light on limitations of the consent modality. Results suggest that through a diverse research team, the recruited sample exceeds traditional measures of representation (e.g. sex, race, ethnicity). Sex demographics of the study are representative of the local population. Screening for candidates is critical to the success of the consent modality. The consent modality may be modified to increase diversity of study population and accept bilingual candidates. Researchers must implement best practices, including increasing inclusivity of bilingual populations, utilizing technology, and improving participant follow-up, to improve health disparities for understudied clinical populations.

Uniform illumination is a key requirement in different research fields. However, this requirement is often difficult to achieve when high intensity is required at the same time. Recent advancements in LED lamps allow nowadays for compact and economical solutions. In this work we present a suitable solution for various laboratory purposes requiring stable, uniform and high intensity illumination. The system is composed of four identical high power white LED arrays of 30 mm diameter each, placed on a supporting and cooling structure having a minimum volume of 26 cm x 26 cm x 8 cm. A numerical model has been developed, based on a ray tracing software, in order to simulate the performances. These have then been experimentally validated with measurements of the power density map, carried out with a 1% uncertainty pyranometer. Data show that the built system is very stable over time and provides an illumination uniformity higher than 98%, on a surface of 50 mm radius, which reduces to 95% on a surface of 75 mm radius. The power density can be adjusted in the 390-1360 W m-2 range, not affecting uniformity.

In the U.S. 44% of low-income households struggle to pay their utility bills, affecting their ability to afford necessities such as food and health expenses. Several government and utility funded energy efficiency programs exist to assist those experiencing energy insecurity. In Salt Lake City, Utah, there is a high demand for, but low availability of, energy efficiency services in underserved neighborhoods creating an opportunity for creative community-based programs to fill this inherent gap. This pilot project, involving the exchanging of LED bulbs in Salt Lake City, highlights the development of a community-based energy efficiency program that aims to bring energy savings to a uniquely targeted portion of the city and determines its feasibility in addressing energy insecurity at a larger scale. Through the 8-month project duration, 1,432 bulbs were exchanged at 23 events reaching 181 households in low-income areas. Through a year of use, these bulbs are estimated to save residents approximately 18,219 USD in electricity bills and reduce CO2 emissions from power plants by 122.23 metric tons, in addition to a savings of 4,400 USD in social cost of carbon as defined by the U.S. Environmental Protection Agency. Since this pilot reached less than 1% of households, we extrapolated a reach of 2%, 5%, and 7.5% and found substantial potential decreases in power plant emissions and financial savings. As this project is ongoing and being expanded, we discuss relevant findings that will help shape future community-based models so that they are appropriately deployed and more effective in alleviating local energy insecurity.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

Gold nanoparticles (AuNPs) exhibit improved optical and spectral properties compared to bulk materials, making them suitable for detection of DNA, RNA, antigens, and antibodies. Here, we describe a simple, selective, and rapid non-cross linking detection assay, using approx. 35 nm spherical Au nanoprobes, for a common mutation occurring in exon 19 of the epidermal growth factor receptor (EGFR), associated with non-small cell lung cancer cells. AuNPs were synthesized based on the seed-mediated growth method and functionalized with a specific 16 bp thiolated oligonucleotide using a pH-assisted method. Both AuNPs and Au nanoprobes proved to be highly stable and monodisperse by ultraviolet-visible spectrophotometry, dynamic light scattering (DLS) and electrophoretic light scattering (ELS). Our results indicate a detection limit of 1.5 µg mL−1 using a 0.15 nmol dm−3 Au nanoprobe concentration. In conclusion, this work is an effective possibility for a straight-forward, fast, and inexpensive alternative for the detection of DNA sequences related to lung cancer, leading to a potential platform for an early diagnosis of lung cancer patients.

In this work, we report manganese phthalocyanine (MnPc) films obtained by ultrasonic spray-pyrolysis technique at 40°C deposited on glass substrate subjected to thermal annealing at 100 °C and 120°C. The MnPc films were characterized by UV/Vis spectroscopy, Raman spectroscopy, X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The absorption spectra of the MnPc films were studied in a wavelength range from 200 to 850 nm, where the characteristic bands of a metallic phthalocyanine known as B and Q bands were observed in this range of the spectrum. The optical energy band (Eg) was calculated by the Tauc equation. It was found that for these MnPc films, the Eg has the values of 4.41, 4.46 and 3.58 eV corresponding to as deposited, annealing 100°C and 120°C, respectively. The Raman spectra of the films showed their characteristic vibrational modes of the MnPc films. In X-ray diffractograms of these films, the characteristic diffraction peaks of a metallic phthalocyanine are observed, presenting a monoclinic phase. SEM images of these films were studied in cross section obtaining thicknesses of 2, 1.2 and 0.3 μm to as deposited, annealing 100°C and 120°C, successively. Also, in the SEM images of these films, both the average particle sizes ranging from 4 to 0.041 µm and the average diameter from 4.8 to 0.091 μm were obtained. The results agree with those reported in the literature for MnPc films deposited with other techniques.

Euglenoids are a common component of primary producers in high acidic and organic shallow freshwater systems. They are free-living photosynthetic motile flagellates exhibiting rapid responses to various external stimuli including chemical pollution. The unique combination of diverse physiological processes of Euglena such as photosynthesis, movement, and orientation offers a range of sensitive criteria that respond to aquatic pollutants. This has led to the development of several acute and chronic assay methods to monitor the adverse impacts of potent toxicants in aquatic ecosystems. Euglenoids also reflect the consequences of physical stress factors such as UV radiation. This review summarizes the ecotoxicity studies using euglenoid flagellates as model species and their potential to contribute toward rapid screening of ecological impacts of pollution in the aquatic environment. Factors determining the reliability of Euglena tests are outlined.

There is experimental evidence of high vibronic activity that accompanies the strongly allowed transition between the ground state and the lowest electronic singlet excited state of oligofurans that contain 2,3, and 4 furan rings. The absorption and emission spectra of the three lowest oligofurans measured in liquid nitrogen temperature show distinct fine structures that are reproduced using the projection-based model of vibronic coupling (with Dushinsky rotation included) parameterized utilizing either DFT (with several different exchange-correlation functionals) or ab initio (CC2) quantum chemistry calculations. Using as reference the experimental data concerning the electronic absorption and fluorescence for the 8 lowest oligofurans we first analyze the performance of the exchange-correlation functionals for the electronic transition energies and the reorganization energies. Subsequently, we use the best functionals alongside the CC2 method to explore how the reorganization energies are distributed among the totally symmetric vibrations, identify the normal modes that dominate in the fine structures present in the absorption and emission bands, and trace their evolution with the increasing number of rings in the oligofuran series. Confrontation of the simulated spectra with the experiment allows for verification of the performance of the selected DFT functionals and the CC2 method.

Glass samples (59.5 – x) B2O3 – 20Na2O – 20CaO – xV2O5 – Er2O3 – 0.5AgCl (x = 0 – 2.5 mol%) were prepared using melt – quenching method to investigate the structural and optical properties of the glass. The structural of the glass were characterized by using XRD, TEM and FTIR, meanwhile the optical properties were characterized by UV – VIS absorption. The XRD patterns confirmed the amorphous nature of the prepared glass samples. FTIR confirmed the presence of VO4, VO5, BO3, and BO4 vibration, and this result showed NBO increased with increasing vanadium concentration. The UV – Vis – NIR spectra exhibits six absorption band centered at 490, 520, 540, 660, 800, and 980 nm. The optical band gap (Eopt), Urbach energy and refractive index shown decrease, increase and increase, respectively. The Judd – Ofelt intensity parameter reveal the trends was Ω2 &gt; Ω4 &gt; Ω6. There are three emission bands at 516 nm, 580 nm, and 673 nm which are represented by 2H11/2 – 4I15/2, 4S3/2 – 4I15/2, and 4F15/2 – 4I15/2, respectively under 800 nm excitation was obtained.

A prominent feature of stress-tolerant microalgae is their versatile metabolism allowing then to synthesize a broad spectrum of molecules with beneficial effects on many aspects of human body functioning. This is in line with the current understanding that many stress-induced deleterious processes in the human body and in photosynthetic cell are mediated by the same mechanisms such as free-radical attacks and lipid peroxidation. These related risks are kept at bay by optical screening of harmful UV, enzymatic ROS elimination systems, and potent low-molecular antioxidants. Microalgae synthesize a broad spectrum of compounds exerting antioxidant and/or UV-absorbing properties. In microalgae, they increase stress-resilience of these organisms. In human body, they exhibit photoprotective, antiaging, and sunscreen activities. Therefore, these algal metabolites were recognized as promising ingredients for innovative cosmetics and cosmeceutical formulations. Ever increasing effort is being invested into the search for new natural biologically active substances from microalgae. This trend is also fueled by the growing demand for natural raw materials for food, pharmaceuticals and cosmetology associated with the global transition to a "greener" lifestyle. Here, we review the currently accumulated knowledge about the main groups of cosmeceutical compounds from microalgae.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Given the recent advances in information technology, speed has become an important requirement in data transmission. Given that an LED (light emitting diode) can turn on and off several thousand or even millions of times per second, then LiFi (light fidelity) technology has strong advantages over WiFi (wireless fidelity) in terms of speed. In this research project, a consortium involving an academic institution decided to evaluate the maturity of LiFi technology and design a demonstrator that could be integrated in a vehicle via an intra-vehicle data transmission system. The demonstrator is to implement a two-way LiFi communication between the reading light of a vehicle and a portable device such as a tablet or smartphone. The nomadic device must display, via an interface, data in real time. The data is RNT (Digital Terrestrial Radio) and TNT (Digital Terrestrial Television) provided by an in-house antenna. LiFi depends on optical technology. The optical characteristics have significant influences on the system. The paper shows ways to improve the system’s throughput, communication range, and reception area. By replacing the reading light with a more powerful one with better optical characteristics, the communication range and reception area improve. By using symmetrical power supply, the throughput improves. Likewise, by using optical filters that eliminate noise, the throughput also improves. We have demonstrated that LiFi data transmission in the vehicle is feasible; low-definition videos were successfully transmitted. The paper acknowledges that there are still various avenues for this work’s improvement.

The effectiveness of simple weirs and the ability of rural farmers to construct durable weirs are still areas of concern in rural areas in Zambia. The objective of this study is to investigate the factors contributing to the varying levels of durability of the simple weir structures used for the diversion of river flows. This study was conducted in 5 districts where 33 SWs located in similar geographical zones were analyzed for their longevity. The research delved into catchment and climatic variables, and the social and psychological perception of simple weirs. The study conducted interviews with key informants who were familiar with the use of SWs in 5 districts in Muchinga provinces between 26 December 2023 and 15 January 2024 using semi-structured questions. The findings of this study indicated that simple weirs constructed on relatively square-shaped catchments and narrow-shaped catchment areas were less vulnerable to damage and easy to operate and maintain. The study also found that climatic factors such as storm rainfall events had little impact on the operation and maintenance of these weirs in Muchinga province, as most sites are in the rainfall shadow while farmers` views about the structures varied from site to site. Overly, planning is necessary for implementing small or large irrigation structures.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

Plastic materials have revolutionized modern life, particularly in the domain of food packaging, owing to their versatility, lightweight nature, and ease of processing. However, the environmental ramifications of non-degradable plastics have raised concerns. Polylactic acid (PLA), derived from renewable sources, presents a sustainable alternative due to its biodegradability and exceptional barrier, mechanical, and safety properties. Nevertheless, the high UV transmittance of PLA limits its use for photosensitive food and pharmaceutical packaging, where UV radiation can lead to nutritional loss and spoilage. Various methods have been explored to enhance the UV-blocking capabilities of PLA, including the integration of inorganic nanoparticles and surface coatings. Despite advancements, these approaches often compromise the inherent transparency of PLA. Incorporating large conjugated groups can maintain transparency but introduces additional challenges. This paper reviews modification methods to enhance PLA's UV-barrier properties and anticipates its expanded utility in food and drug packaging, promoting UV resistance and diversifying PLA's applications.

Petrosamine (1) – a colored pyridoacridine alkaloid from the Belizean sponge, Petrosia sp. that is also a potent inhibitor of acetylcholine esterase (AChE) – was investigated by spectroscopic and computational methods. Analysis of the petrosamine free energy landscapes, pKa and tautomerism revealed an accurate electronic depiction of the molecular structure of 1 as the di-keto form, with net charge of q = +1, rather than a dication (q = +2) under ambient conditions of isolation-purification. The pronounced solvatochromism (UV-vis) reported for 1, and related analogs, was investigated in detail and is best explained by charge delocalization and stabilization of the ground state (HOMO) of 1 rather than an equilibrium of competing tautomers. Refinement of the molecular structure of 1 by QM methods complements published computational docking studies to define the contact points in the enzyme active site that may improve design of new AChE inhibitors based on the pyridoacridine alkaloid molecular skeleton.

This joint experimental-theoretical work focuses on molecular and photophysical properties of the spiropyran-containing amphiphilic molecule in organic and aqueous solutions. Being dissolved in tested organic solvents, the system demonstrates positive photochromism, i.e. upon UV stimulus the colorless spiropyran form is transformed into colorful merocyanine isomer. However, aqueous solution of the amphiphile possesses a negative photochromism: the orange-red merocyanine form turns to be thermodynamically more stable in water, and both UV and vis stimuli lead to the partial or complete photobleaching of the solution. The explanation of this phenomenon is given on the basis of density functional theory calculations and classical modeling including thermodynamic integration. The simulations reveal that stabilization of merocyanine in water proceeds with the energy of ca. 70 kJ mol−1, and that the Helmholtz free energy of hydration of merocyanine form is 100 kJ mol−1 lower as compared to the behavior of SP isomer in water. The explanation of such a difference lies in the molecular properties of the merocyanine: after ring-opening reaction this molecule transforms into a zwitterionic form, as evidenced by the electrostatic potential plotted around the opened form. The presence of three charged groups on the periphery of a flat conjugated backbone stimulates the self-assembly of merocyanine molecules in water, ending up with the formation of elongated associates with stack-like building blocks, as shown in molecular dynamics simulations of the aqueous solution with the concentration above critical micelle concentration. Our quantitative evaluation of the hydrophilicity switching in spiropyran/merocyanine containing surfactants may prompt the search for new systems, including colloidal and polymeric ones, aiming at remote tuning of their morphology, which could give new promising shapes and patterns for the needs of modern nanotechnology.

More than twenty-five years ago the Global Solar UV index (UVI) has been introduced as a simple means of visualizing the intensity of ultraviolet radiation and to alert people to the need for sun protection. In our survey among directors of 436 kindergartens in southern Germany we investigated the level of awareness and knowledge about the UVI as well as the practical consequences for sun protection in kindergartens. Less than half of the directors (n=208, 47.7%) had ever heard of the UVI, and only a small minority of them (n=34, 8.7%) used the daily UVI information to adapt sun protective measures in their kindergartens. Detailed knowledge about the UVI was a rarity among the respondents. The proportion of respondents with self-perceived detailed UVI knowledge was five times higher than actual knowledge assessed by an in-depth structured interview using open-ended questions about the UVI (14.2% vs. 2.8%). No clear relationship of UVI awareness, knowledge, and use to directors' age and gender was found. The UVI-related variables also showed no association with directors' knowledge of risk factors for skin cancer and their attitudes towards tanned skin. Overall, the results paint a sobering picture regarding the penetration of the UVI into sun protection policies of German kindergartens. Future public health campaigns should target increasing awareness and understanding of the UVI as well as its importance for sun protection of children.