GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The features of a class of cubic curves with a shape factor are analyzed by means of the theory of envelope and topological mapping. The effects of the shape factor on the cubic curves are made clear. Necessary and sufficient conditions are derived for the curve to have one or two inflection points, a loop or a cusp, or to be locally or globally convex. Those conditions are completely characterized by the relative position of the edge vectors of the control polygon and the shape factor. The results are summarized in a shape diagram, which is useful when the cubic parametric curves are used for geometric modeling. Furthermore we discussed the influences of the shape factor on the shape diagram and the ability for adjusting the shape of the curve.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

The biophysical consequences of nanoscale curvature have been challenging to resolve due to size-dependent membrane behavior and the experimental resolution limits imposed by optical diffraction. Recent advances in nanoengineering and super-resolution techniques have enabled new capabilities for creating and observing curvature. In particular, draping supported lipid bilayers over lithographically patterned substrates provides a model system for endocytic pits. The experiments and simulations presented below describe the possible detection of membrane curvature through fluorescence recovery after photobleaching (FRAP), fluorescence correlation spectroscopy (FCS), single particle tracking (SPT), and polarized localization microscopy (PLM). FRAP and FCS depend on diffraction-limited illumination and detection. In particular, a simulation of FRAP shows no effects on lipids diffusion due to a 50 nm diameter membrane bud at any stage in the budding process. Simulated FCS demonstrated small effects due to a 50 nm radius membrane bud that was amplified with curvature-dependent lipid mobility changes. However, PLM and SPT achieve sub-diffraction-limited resolution of membrane budding and lipid mobility through the identification of the single-lipid positions with ≤15 nm spatial and ≤20 ms temporal resolution. By mapping the single-lipid step lengths to locations on the membrane, the effects of curvature on lipid behavior have been resolved.

The early Paleozoic is a crucial period in the formation and evolution of the Eastern Kunlun Orogenic Belt (EKOB), and is of great significance for understanding the evolutionary history of the Proto-Tethyan Ocean. This paper presents new petrography, geochemistry, zircon U–Pb dating, and Lu–Hf isotopic research on the Yuejingshan gabbro from the eastern segment of the EKOB. Zircon U–Pb data suggests that the gabbro formed in the Early Silurian (435 ± 2 Ma). All samples have relatively low TiO₂ contents (0.45–2.97%), widely varying MgO (6.58–8.41%) and Mg^# (58–65) contents, and are rich in large ion lithophile elements (LILE such as Rb, Ba, Th, and U) and light rare earth elements (LREE). This indicates that it has a similar geochemical composition to island arc basalt. The major element features indicate that the formation of this gabbro underwent fractional crystallization of clinopyroxene, olivine, and plagioclase. The depletion of high field strength elements (HFSE, such as Nb, Ta, and Ti), and a slightly positive Hf isotope (with εHf_(t) ranging from 1.13 to 2.45) may be related to the partial melting of spinel-bearing peridotite, led by slab fluid metasomatism. The gabbro likely represents magmatic records of the latest period of the early Paleozoic oceanic crust subduction in the Eastern Kunlun. Therefore, the final closure of the Proto-Tethyan Ocean and the beginning of collisional orogeny occurred before the Early Silurian.

Zircon xenocrysts from alkali basalts in Ratanakiri Province, Cambodia, represent a unique low-Hf zircon, within a 12,000 km long Indo-Pacific megacryst zone. Colourless, yellow, brown and red crystals ({100}, {101}, subordinate {211}, {1103}), with hopper growth and corrosion features, range up to 20 cm in size. Zircon chemistry implicates juvenile, Zr-saturated, mantle-derived alkaline melt (Hf 0.6–0.7 wt%, Y <0.2 wt%, U+Th+REE <600 ppm, Zr/Hf 66–92, Eu/Eu*_N ~ 1, positive Ce/Ce*_N, HREE enrichment). Incompatible element depletion with increasing Yb/Sm_N from core to rim at ~ constant Hf suggests single stage growth. Ti-in-zircon temperatures (~570–740 °C) are lower than predicted by crystal morphology (800–900 °C) and decrease from core to rim (D_T = 10–50 °C). The d¹⁸O values (4.88 to 5.01‰ VSMOW) are relatively low for xenocrysts from the zircon Indo-Pacific zone (ZIP). The ¹⁷⁶Hf/¹⁷⁷Hf values (+ εHf 4.5–10.2) give T_{Depleted Mantle} model source ages of 260–462 Ma and T_Crustal ages of 391–754 Ma. The source magmas reflect variably depleted lithospheric mantle with little supracrustal input. Zircon U-Pb (0.88–1.56 Ma) and (U-Th)/He (0.86–1.02 Ma) ages are older than host basalt ages (~0.7 Ma), suggesting limited residence before transport. Zircon genesis suggests Zr-saturated, Al-undersaturated, carbonatitic-influenced, low-degree partial melting (<1%) of peridotitic mantle at ~60 km beneath the Indochina terrane.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A series of precise data consisting of zircon U–Pb ages, whole-rock geochemistry and Sr–Nd–Hf isotope compositions from the Huhetaoergai granitic pluton was collected in this study and combined with data from the western Huhetaoergai, Zhuxiaogubuhe and Yagan granitic plutons to constrain the petrogenesis and tectonic setting of granitic plutons in the northern Ya-Gan fault zone, North Alxa, China. The Huhetaoergai pluton is composed of hornblende diorite, medium- to coarse-grained biotite adamellite and coarse-grained biotite adamellite with K-feldspar megacrysts. The U–Pb zircon ages of biotite adamellite are 220.5 ± 1.9 Ma and 226.5 ± 2.4 Ma. These granitoids are I-type granites with highly radiogenic initial ⁸⁷Sr/⁸⁶Sr of 0.708085–0.735470, negative eNd(t) average values of −2.98–3.23 and high eHf(t) of 9–11.05. These features indicate the granitoids were formed from magmas generated from juvenile crust. We speculate that the granitoids of the Huhetaoergai pluton were emplaced during an episode of intense intraplate orogenic movement evolution in an extrusional setting after a period of extensional postcollisional intraplate evolution.

Looking at different operating climatic conditions, the electrical behavior predicting photovoltaic modules gets very important. For the estimation of output power from photovoltaic (PV) plants this is a very essential and basic aspect. In this paper, the relationship between the I-V curve and the irradiation spectrum is discussed by combining the single diode model. An explicit elementary analytical model with two defined shape parameters is discussed and improved with three approximations and second order Taylor expansion. Then, the explicit elementary analytical model is investigated under varying conditions leveraging the four parameters I_ph, I₀, R_s and R_sh from the single diode model. The relationship between the physical parameters and the condition parameters are discussed and applied to extract the shape parameters at different scenarios. Considering the aging effect, the process of calculation to predict the I-V curve under different splitting spectra is simplified as follow: (1) two shape parameters are gotten from the I-V data at measurement reference conditions (MRC); (2) the short circuit current, open circuit voltage and shape parameters under any splitting spectrum can be calculated based on the relationship provided in article; (3) the performance of PV panel can be predicted with parameters. The validation of this model was experimentally proven leveraging monocrystalline silicon photovoltaic module with different splitting films. Results showed that the model accurately predicts the I-V characteristics for the examined PV modules at different irradiance spectra and cell temperatures. Moreover, the presented model performs superior compared to other investigated models when looking at accuracy and simplicity.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

This paper reports a rational design of temperature-responsive nanofiber meshes with shape-memory effect. The meshes were fabricated by electrospinning a poly(ε-caprolactone) (PCL)-based polyurethane with different contents of soft and hard segments. The effects of PCL diol/hexamethylene diisocyanate (HDI)/1,4-butanediol (BD) molar ratio in terms of the contents of soft and hard segments on the shape-memory properties were investigated. Although the mechanical property improved with increasing hard segment ratio, optimal shape-memory properties were obtained with a PCL/HDI/BD molar ratio of 1:4:3. At a microscopic level, the original nanofibrous structure was easily deformed into a temporary shape, and recovered its original structure when the sample was reheated. A higher recovery rate (>89%) was achieved even when the mesh was deformed up to 400%. Finally, the nanofiber meshes were used to control the alignment of human mesenchymal stem cells (hMSCs). The hMSCs aligned well along the fiber orientation. The proposed nanofibrous meshes with the shape-memory effect have the potential to serve as in vitro platforms for the investigation of cell functions as well as implantable scaffolds for wound-healing applications.

The possibility of releasing gold nanoparticles (GNP) into the environment has been rapidly increasing with the wide spread and flourishing application of gold nanoparticles (GNPs) in a wide range of areas. Consequently, environmental effects of GNP, especially toxicities to living organisms have drawn great attention. However, their toxicological characteristics still remain unclear. Fungi, as the decomposers of the ecosystem, interact directly with the environment and critically control the overall health of the biosphere. Thus, their sensitivity to GNP toxicity is particularly important. The aim of this study was to evaluate the role of shape and size of GNPs on their toxicities to fungi, which could help reveal the ecotoxicity of GNPs. Aspergillus niger, Mucor hiemalis and Penicillium chrysogenum were chosen for toxicity assessment, and spherical and star/flower-shaped GNPs sized from 0.7 nm to large aggregates of 400 nm have been synthesised. After exposure to GNPs and their corresponding reaction agents and incubation for 48 hours, the survival rates of each kind of fungus was calculated and compared. The results indicated that fungal species was the major determinant of the variation of survival rates, whereby A. niger was most sensitive and M. himalis was least sensitive to GNP exposure. Additionally, larger and non-spherical GNPs had relatively stronger toxicities.

Knowledge about the formation energies of compounds is essential to derive phase diagrams of multi-component phases with respect to elemental reservoirs. The determination of formation energies using common (semi-)local exchange-correlation approximations of density functional theory (DFT) exhibits well-known systematic errors if applied to oxide compounds containing transition metal elements. In this work, we generalize, reevaluate and discuss a set of approaches proposed and widely applied in the literature to correct for errors arising from the over-binding of the O2 molecule and from correlation effects of electrons in localized transition-metal orbitals. The DFT+U method is exemplarily applied to iron oxide compounds, and a procedure is presented to obtain U values, which lead to formation energies and electronic band gaps comparable to experimental values. Using such corrected formation energies, we derive the phase diagrams for LaFeO3, Li5FeO4 and NaFeO2, which are promising materials for energy conversion and storage devices. A scheme is presented to transform the variables of the phase diagrams from the chemical potentials of elemental phases to those of precursor compounds of a solid-state reaction, which represents the experimental synthesis process more appropriately. The discussed workflow of methods can directly be applied to other transition metal oxides.

Effect of abrasive shape on the three-body abrasion behaviors of monocrystalline silicon was investigated by Molecular dynamics modelling. The axial ratio of abrasive particle was varied from 1.00, i.e., a complete sphere, to 0.40 to mimic abrasive shape. The particle’s movement turns toward sliding from rolling when the axial ratio becomes less than a critical value 0.46. In the abrasion process, the friction force and normal force showed an approximately sinusoid-like fluctuation for the rolling ellipsoidal particles, while the front cutting of particle caused that friction force increased and became larger than normal force for sliding particles. The phase transformation process was tracked under different particle’ movement patterns. The Si-II and Bct5 phase producing in loading process can partially transform to Si-III/Si-XII phase and backtrack to original crystal silicon under pressure release, which also occurred in the abrasion process. The secondary phase transformation showed difference for particles’ rolling and sliding movements after three-body abrasion. The rolling of particle induced the periodical and inhomogeneous deformation of substrates, while the sliding benefited producing high-quality surface in CMP process. This study aiming to construct more precise model to understand the wear mechanism benefits evaluating the MEMS wear and CMP process of crystal materials.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

The research sought to investigate the long term characteristics of wind in the Kisii region (elevation 1710m above sea level, 0.68^oS, 34.79^o E). Wind speeds were analyzed and characterized on short term (per month for a year) and then simulated for long term (ten years) measured hourly series data of daily wind speeds at a height of 10m. The analysis included daily wind data which was grouped into discrete data and then calculated to represent; the mean wind speed, diurnal variations, daily variations as well as the monthly variations. The wind speed frequency distribution at the height 10 m was found to be 2.9ms^-1 with a standard deviation of 1.5. Based on the two month’s data that was extracted from the AcuRite 01024 Wireless Weather Stations with 5-in-1 Weather Sensor experiments set at three sites in the region, averages of wind speeds at hub heights of 10m and 13m were calculated and found to be 1.7m/s, 2.0m/s for Ikobe station, 2.4m/s, 2.8m/s for Kisii University stations, and 1.3m/s, 1.6m/s for Nyamecheo station respectively. Then extrapolation was done to determine average wind speeds at heights (20m, 30m, 50m, and 70m) which were found to be 85.55W/m², 181.75W/m², 470.4W/m² and 879.9W/m² respectively. The wind speed data was used statistically to model a Weibull probability density function and used to determine the power density for Kisii region.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.

Shape memory alloys (SMAs) are increasingly used in the fields of aviation, automotive and biomedicine due to their unique properties. Nickel-Titanium (NiTi) alloy materials, which are one of the shape memory alloys, are among the most frequently used alloy materials. The shape memory and super elastic effects of NiTi alloys, high ductility and deformation hardening make it difficult to shape burr. An additional problem is the formation of a white layer during machining. In this study, surface milling operations were performed in dry cutting conditions with uncoated cutting tools with different nose radii. The processing parameters were determined based on the experience gained as a result of the preliminary tests. Tungsten carbide cutting tools with different nose radii (0.4mm and 0.8mm) were used for the milling operations. Milling was carried out at three different cutting speeds (20, 35, 50 m/min), feed rates (0.03, 0.07, 0.14 mm/tooth), and a constant axial cutting depth (0.7 mm). As a result of our experimental studies, the best tool life was found to be in 0.8 mm nose radius cutting tools at 20 m/min cutting speed and 0.03 mm/tooth feed rate (0.264 mm). The minimum average surface roughness was found after milling with 0.8 mm nose radius cutting tool at 20 m/min cutting speed and 0.03 mm/tooth feed rate (0.346 μm). It has been determined that increasing the cutting tool nose radius reduces both the flank wear over the cutting tool and the average surface roughness.

This work deals with aerofoil aerodynamic features optimization, not only to improve flight features, but also to improve economy, ecology and safety of parameters of flight technique. In cruise mission, occupying the most flight time, the most important parameter is aerodynamic drag, which directly influences the aeroplane operational economy of transportation. Drag reduction is adequately reflected in the fuel consumption reduction. Consumption reduction is also adequately reflected in the flight ecology. In take-off and landing mission, the safety is priority and directly influences the aerofoil geometry. For cruise mission the new modified evolutionary algorithms (EA) are used to parameters incoming to Bezier-PARSEC 3434 parametrization. Such aerofoil is processed and evaluated by the Xfoil program. The change of model parameters results to optimal aerofoil shape. The DCAG (Direct Control Aerofoil Geometry) is unique developed mechanical device, makes possible the change of curvature of aerofoil, and also aerofoil geometry. DCAG is based on the rotary principle, which makes it possible to define the curvature of aerofoil for every roll as well as defining the geometry in the variable parts of aerofoil. For take-off and landing mission the best combination of slots and flaps is choosed. To improve of laminarity and reduce turbulent flow the DCAG is used. The work results to optimization, which is 50 times faster in comparison to ordinary optimization, with minimum of input parameters (flight speed, chord length, range of angles of attack and fitness function). The optimized aerofoil can achieve savings in fuel consumption up to 44% in comparison with unoptimized aerofoil, the aerodynamic drag reduction up to 44%. The output was checked by ANSYS Fluent simulation.

Background: Research continues to search for blood-based biomarkers sensitive to Alzheimer’s disease (AD) pathology during the initial stages when symptoms of cognitive decline are not yet apparent. A blood-based biomarker candidate is metalloprotein p53, the conformation of which was previously found to be altered in peripheral cells from individuals with mild cognitive impairment (MCI) and AD, presenting as an unfolded p53 (U-p53) conformational variant. Methods: Plasma samples from the well-characterized Australian Imaging, Biomarkers, and Lifestyle (AIBL) cohort were used to identify the clinically relevant AZ 284^® peptide, specifically present in samples from individuals with symptomatic AD. The AZ 284^® peptide, which is a marker of the U-p53 conformational variant (U-p53^AZ), was identified by immunoprecipitation (IP) with a novel U-p53 conformational variant-specific antibody followed by liquid chromatography (LC) tandem mass spectrometry (MS/MS) and protein sequencing. Using IP-LC surface-activated chemical ionization (SACI) MS/MS analysis, the prognostic and diagnostic performance of U-p53^AZ were examined in the longitudinal AIBL cohort, including 252 plasma samples derived from 214 elderly individuals. For the prognostic analyses, U-p53^AZ levels were assessed at 36, 72, and 90 months after baseline assessment. Results: The prognostic performance of U-p53^AZ to predict the progression to AD from preclinical or prodromal AD was high, with area under the receiver operating characteristic curve (AUC) values close to or above 0.90. Furthermore, U-p53^AZ predicted the progression to AD more than 6 years prior to symptom onset with positive and negative predictive values of about 90%. Additionally, the estimated prognostic performance of U-p53^AZ was superior to other main risk factors (i.e., age, sex, and either alone or in combination with amyloid status. Furthermore, U-p53^AZ had high diagnostic performance to differentiate cognitively normal individuals from those with AD (AUC values >0.88). Conclusion: These findings support the use of U-p53^AZ as a prognostic blood-based biomarker accurately predicting the progression to AD dementia during the preclinical and prodromal stages at least 6 years before receiving the clinical diagnosis of AD dementia.

The aim of this work is to analyze and investigate the shape preserving properties of ternary 4-point non-stationary interpolating subdivision schemes constructed by Beccari et al. [1] with a tension parameter !k+1 which can reproducing exponential. Moreover, the conditions on the initial control points are developed that allow user to generate shape preserving limit curves after a nite number of subdivision steps and generalize these results in limiting case. Signicance of derived conditions are illustrated through graphs and the whole discussion is followed by examples.

A systematic approach for model updating using the modal identification results is proposed. Modal identification provides mode shapes for physical quantities (acceleration strain, etc.) measured in specific directions at the location of the sensors. Besides, model updating involves the use of the mode shapes related to the nodal degrees-of-freedom of the finite element analytic model. Consequently, the mode shapes obtained by modal identification and the mode shapes of the model updating process do not coincide even for the same mode. Therefore, a method constructing transform matrices that distinguish the cases where measurement is done by acceleration, velocity and displacement sensors and the case where measurement is done by strain sensors is proposed to remedy such disagreement between the mode shapes. The so-constructed transform matrices are then applied when the mode shape residual is used as objective function or for mode pairing in the model updating process. The feasibility of the proposed approach is verified by means of a numerical example in which the strain or acceleration of a simple beam is measured and a numerical example in which the strain of a bridge is measured. Using the proposed approach, it is possible to model the structure regardless of the position of the sensors and to select the location of the sensors independently from the model.

Based on a measuring system to determine levels of spatial organization in 2D polygons (homogeneous or heterogeneous partition of defined areas) lying on principles of regularity, we propose the entropy term linked to the concept of “information”, from the “information theory field”, in order to obtain an information measurement regarding a quantity of or amount of information in the architecture of complex 2D biological organizations. The term “quantity” does not refer to the amount of data (size), but to the probability of a geometrical basic pattern within a set of possible statistical configurations regarding levels of homogeneity and heterogeneity. It is this notion of information that is important in information theory, and measures of information in units of bits, what we propose to use for measuring quantities of organization in the architecture of complex geometrical systems. Two complex systems are tested, biological and non biological in order to obtain experimental results, which are verified with the evaluation criteria “entropy”. Experimental results show that the lowest levels of information and entropy, in addition with low rates of heterogeneity and high rates of homogeneity are particular features of geometrical organizations in biological systems.

Otolith morphology analysis is one of the main tools used for fish or fish stock identification. Moreover, otolith shape can also be used in fish dietary studies (stomach content) for the identification of prey fishes and their size according to the relationship between fish and otolith sizes. In the present study, the relationship between fish length and otolith morphological dimensions was investigated for the sabre squirrelfish, Sargocentron spiniferum (Forsskål, 1775) (family: Holocentridae). Samples of 185 fish were collected from the coast of the Red Sea, Egypt. To analyze the relationship between fish and otolith, otolith morphometric measurements (length, width, area, perimeter, weight, sulcus, and ostium) and shape factors (aspect ratio, compactness, form factor, rectangularity, roundness, ellipticity, squareness) describing outline shape were extracted using image analysis. Generalized linear models were applied for the relationship between body length and each otolith morphology feature. From the relationships between the total length of fish and fourteen morphology features, only otolith length, caudal length, and squareness were significantly correlated with fish size. Our results provide more information for the relationship between fish length and otolith morphometric features.

In this study, we report a new epoxy acrylate based shape memory polymer(SMP) fabricated by Liquid crystal display (LCD) Stereolithographic 3D printing. The printed 3D object has a high resolution and high transparency in visible light region. The uniaxial tensile tests showed enhanced tensile toughness and tunable mechanical properties. The fix-recovery and cycle tests indicated high shape recovery properties including high shape recovery rate and excellent cycling stability. In addition, a smart electrical valve actuator was fabricated that can be used in fast heat or electricity responsive electrical circuits. LCD 3D printing provides a low-cost and high efficient way to fabricate fast responsive SMP, which can be used in wide applications in various fields on aerospace engineering, biomedical devices, soft robots and electronic devices.

This purpose was to compare the ability of body shape index (ABSI) and body roundness index (BRI) with waist circumference (WC), body mass index (BMI), waist-to-hip ratio (WHR), waist-to-height ratio (WHtR) and body adiposity index (BAI) to predict metabolic risk. The cross-sectional study was conducted in 17,360 Chinese subjects (were aged 18-95 years old) who escaped cardiovascular disease (CVD) or diabetes. Biochemical and anthropometric variables were measured by trained staff. Receiver operating characteristic curve (ROC) and optimal cutoff values of obesity indices were recruited to compare the predictive ability for metabolic risk factors. The mean age of subjects was 53.7(13.1) years, 41.6 % were males. Within young group (<60 years), the areas under the curve (AUC) demonstrated that WC, BMI, WHR, WHtR and BRI were able to similarly predict high metabolic risk in males (0.74 vs. 0.74 vs. 0.73 vs. 0.73 vs. 0.73) and in females (0.73 vs. 0.73 vs. 0.71 vs. 0.73 vs. 0.73), while the approximate predictive ability were only acquired in males (0.73 vs. 0.73 vs. 0.70 vs. 0.73 vs. 0.73) within elder group (≥60 years). The optimal cut-off values of BRI for high metabolic risk were calculated in males (<60 y: 3.49 vs. ≥60 y: 3.46) and females (<60 y: 3.47 vs. ≥60 y: 3.60). Meanwhile, BRI displayed a strong prediction to elevated BP and elevated TG in males (AUC = 0.64; AUC = 0.70) and to elevated BP, elevated TG and elevated SUA in females (AUC = 0.67; AUC = 0.69; AUC =0.70). BRI was able to similarly predict high metabolic risk compared to WC, BMI, WHR, WHtR and BAI, while ABSI was not. Moreover, BRI revealed specific predictive ability for elevated BP, elevated TG and elevated SUA.

A common spinal condition, spondylolisthesis is the presence of a relative back or forth displacement between the upper and lower vertebra due to one vertebra being oriented away from the smooth curvature of a normal spine. Aging-related illnesses such as degenerative spondylolisthesis are especially burdensome on social welfare and health-care systems in an aging society, especially radiologists and clinical physicians. Therefore, we proposed a computer aided diagnosis algorithm, named LumbarNet, for vertebral slippage detection on clinical X-ray images. Collaborating with i) a P-grade, ii) a piecewise slope detection scheme, and iii) a dynamic shift detection routine, LumbarNet was thus specialized for analyzing complex structural patterns in lumbar spine X-ray images and outcompeted other U-Net based methods. Extensive experiments on lumbar spine X-ray images in standard clinical practices showed that LumbarNet achieved a mean intersection over union value of 0.88 in vertebral region detection and an accuracy of 88.83% in vertebral slippage detection.

We proposed in this work the introduction of a new vision of stochastic processes through geometry induced by dilation. The dilation matrices of a given process are obtained by a composition of rotation matrices built in with respect to partial correlation coefficients. Particularly interesting is the fact that the obtention of dilation matrices is regardless of the stationarity of the underlying process. When the process is stationary, only one dilation matrix is obtained and it corresponds therefore to Naimark dilation. When the process is nonstationary, a set of dilation matrices is obtained. They correspond to Kolmogorov decomposition. In this work, the nonstationary class of periodically correlated processes was of interest. The underlying periodicity of correlation coefficients is then transmitted to the set of dilation matrices. Because this set lives on the Lie group of rotation matrices, we can see them as points of a closed curve on the Lie group. Geometrical aspects can then be investigated through the shape of the obtained curves, and to give a complete insight into the space of curves, a metric and the derived geodesic equations are provided. The general results are adapted to the more specific case where the base manifold is the Lie group of rotation matrices, and because the metric in the space of curve naturally extends to the space of shapes, this enables a comparison between curves’ shapes and allows then the classification of processes’ measure.

The continuous and precise mapping of glacier calving fronts is essential for monitoring and understanding rapid glacier changes in Antarctica and Greenland, which have the potential for significant sea level rise within the current century. This effort has been mostly restricted to the slow and painstaking manual digitalization of the calving front positions in thousands of satellite imagery products. Here, we have developed a machine learning toolkit to robustly and automatically detect glacier calving front margins in satellite imagery. The toolkit is based on semantic image segmentation using Convolutional Neural Networks (CNN) with a modified U-Net architecture to isolate the calving fronts from satellite images after having been trained with a dataset of images and their corresponding manually-determined calving fronts. As a case study we train our neural network on a varied set Landsat images with lowered resolutions from Jakobshavn, Sverdrup, and Kangerlussuaq glaciers, Greenland and test the results on novel images from Helheim glacier, Greenland to evaluate the performance of the approach. The neural network is able to identify the calving front in new images with a mean deviation of 96.3 m from the true fronts, equivalent to 1.97 pixels on average, while the corresponding error for manually-determined fronts on the same resolution images is 92.5 m. We find that the trained neural network significantly outperforms common edge detection techniques, and can be used to continuously map out calving-ice fronts with a variety of data products.

10% copper substituted (BiCUVOX/Bi₂V_0.9Cu_0.1O_5.5−δ) and 5% copper/titanium double-substituted bismuth vanadate (BiCUTIVOX/Bi₂V_0.9(Cu_0.05Ti_0.05)O_5.5−δ) platelets were formed by molten salt synthesis (MSS) using a eutectic KCl/NaCl salt mixture. The product was phase pure within the limits of X-ray diffraction. The size and form of the platelets could be controlled by changing the heating temperature and time. The crystallite growth rate at a synthesis temperature of 650 °C, and activation energy for grain growth were determined for BICUTIVOX, which experienced inhibited growth compared to BICUVOX. Quasi-equilibrium, multi-foil shapes consisting of lobes around the perimeter of the platelets were observed and explained in the context of relative two-dimensional nucleation and edge growth rates.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

Macula fovea detection is a crucial prerequisite towards screening and diagnosing macular diseases. Without early detection and proper treatment, any abnormality involving the macula may lead to blindness. However, with the ophthalmologist shortage and time-consuming artificial evaluation, neither accuracy nor effectiveness of the diagnose process could be guaranteed. In this project, we proposed a deep learning approach on ultra-widefield fundus (UWF) images for macula fovea detection. This study collected 2300 ultra-widefield fundus images from Shenzhen Aier Eye Hospital in China. Methods based on U-shape network (Unet) and Fully Convolutional Networks (FCN) are implemented on 1800 (before amplifying process) training fundus images, 400 (before amplifying process) validation images and 100 test images. Three professional ophthalmologists were invited to mark the fovea. A method from the anatomy perspective is investigated. This approach is derived from the spatial relationship between macula fovea and optic disc center in UWF. A set of parameters of this method is set based on the experience of ophthalmologists and verified to be effective. Results are measured by calculating the Euclidean distance between proposed approaches and the accurate grounded standard, which is detected by Ultra-widefield swept-source optical coherence tomograph (UWF-OCT) approach. Through a comparation of proposed methods, we conclude that, deep learning approach of Unet outperformed other methods on macula fovea detection tasks, by which outcomes obtained are comparable to grounded standard method.

Otolith morphology analysis is one of the main tools used for fish or fish stock identification. Moreover, otolith shape can also be used in fish dietary studies (stomach content) for the identi-fication of prey fishes and their size according to the relationship between fish and otolith sizes. In the present study, the relationship between fish length and otolith morphological dimensions was investigated for the sabre squirrelfish, Sargocentron spiniferum (Forsskål, 1775) (family: Hol-ocentridae). Samples of 185 fish were collected from the coast of the Red Sea, Egypt. To analyze the relationship between fish and otolith, otolith morphometric measurements (length, width, area, perimeter, weight, sulcus, and ostium) and shape factors (aspect ratio, compactness, form factor, rectangularity, roundness, ellipticity, squareness) describing outline shape were extracted using image analysis. Generalized linear models were applied for the relationship between body length and each otolith morphology feature. From the relationships between the total length of fish and fourteen morphology features, only otolith length, caudal length, and squareness were significantly correlated with fish size. Our results provide more information for the relationship between fish length and otolith morphometric features.

An airfoil is the geometric shape of a cross-section of a wing. When it is exposed to the flow of a fluid over its surface, it generates both lift and drag forces through a pressure distribution. Designing an efficient airfoil for aerodynamic applications is a complex challenge in the field of aerodynamic engineering, with the aim of achieving an optimal lift-to-drag ratio. The success of airfoil design hinges on the effective reduction of drag force under specific conditions, while simultaneously attaining the desired lift without encountering significant flow separation, such as boundary layer shedding. Furthermore, the design must adhere to lifting force limitations and meet structural requirements. In the field of airfoil design and optimization, literature review articles provide a valuable resource by offering an overview of the latest advancements in specific areas. These areas encompass a wide range of topics including the design and testing of adaptive geometry wings, such as morphing wing technology as well as the application of shape optimization techniques to enhance airfoil performance. Our goal is to provide researchers with an in-depth review of relevant articles published to date, examining the applied approaches utilized to tackle the complex problem of airfoil design and explore the methodology employed to address it, from a broad perspective on the topic.

One-dimensional shape memory polymer fibers (SMPFs) have obvious advantages in mechanical properties, dispersion properties and weavability. In this work, a method for fabricating semi-crystallization ethylene-vinyl acetate copolymer (EVA) fiber with two-way shape memory effect by melt spinning and ultraviolet (UV) curing was developed. Here, the effect of crosslink density on its performance was systematically analyzed by gel fraction measurement, tensile tests, DSC and TMA analysis. The results showed that the crosslink density and shape memory properties of EVA fiber could be facilely adjusted by controlling UV curing time. The resulting EVA fiber with cylindrical structure had a diameter of 247.13 ± 10.07 μm, and its mechanical strength and elongation at break were 64.46 MPa and 114.33%, respectively. The critical impact of the crosslink density and applied constant stress on the two-way shape memory effect were analyzed. Moreover, the single EVA fiber could lift more than 143 times its own weight and achieve 9% reversible actuation strain. The reversible actuation capability was significantly enhanced by a simple winding design of the single EVA fiber, which provided great potential applications in smart textiles, flexible actuators and artificial muscles.

In this paper, precise examination of multi-port antennas with large mutual coupling between the ports is studied. For this purpose, some vital parameters such as active reflection coefficients and realised gain are emphasized. The main motivation of this research is the ignorance of this issue in several recently published papers. Hence, corrections and criticisms to some recently reported results are presented. At first, a microstrip patch consisting of two inverted U-slots is re-examined, which has been proposed in a recently published paper for wideband applications. However, the authors did not present satisfactory results to indicate the performance of the proposed structure. In reverse, some important parameters such as the antenna gain appear to be incorrectly reported. In this paper, the characteristics of the antenna are compared with a simple 50 Ω microstrip line excited by two probes, indicating no significant differences. In the remainder of this paper, some corrections are provided on two examples of wide-beam circularly polarised multi-fed antennas for satellite applications. The first example is the multi-fed spiral antennas with folded arms, which have been proposed as the widebeam antennas at 435 MHz. It is indicated that the antenna height should be increased for better performance. The second example is the quadrifilar square helical antennas with folded arms, which have been proposed as the widebeam antennas for 435 MHz with minor responses at 145 MHz. Some corrections are presented on the previously reported minor responses at 145 MHz.

Nowadays, the development or improvement of actuation mechanisms is a crucial topic for the achievement of dextrous manipulation using soft robots. Then, a primary target of research is the design of actuation and driving devices. Consequently, in this paper, we introduce a soft driving epicyclical mechanism that mimics human muscle behavior and fulfills motion requirements to achieve grasping gestures using a robotic finger. The prototype is experimentally assessed, and results show that our approach has enough performance for the implementation in grasping tasks. Furthermore, we introduce the basis for a new soft epicyclical mechanism merger with shape memory alloys to allow active stiffness control of the mechanism.

During the progression from ductal carcinoma in situ (DCIS) to invasive breast cancer (IBC), cells have to overcome the physically restraining basement membrane (BM) which compartmentalizes the epithelium from the stroma. Since the extracellular matrix (ECM) of the epithelial and stromal compartment is biochemically and physically distinct from one another, the progression demands a certain degree of cellular plasticity being essentially required for a primary tumor to become invasive. The Epithelial-to-Mesenchymal Transition depicts such a cell program equipping cancer cells with features allowing for dissemination from the epithelial entity and stromal invasion on the single-cell level. Here, we investigated the reciprocal interference between an altering tumor microenvironment and the EMT-phenotype in vitro. BM-typical collagen IV and stroma-typical collagen I coatings were applied as provisional 2-D matrices. Pro-inflammatory growth factors were introduced to improve tissue mimicry. Whereas the growth on coated surfaces did only slightly affect the EMT-phenotype, the combinatorial action of collagen with growth factor TGF-β1 induced prominent phenotypic changes. However, the EMT-induction was independent of the collagen type and cellular accessibility for EMT-like changes was strongly cell line dependent. Summarizing the entire body of data, we computed an EMT-phenotyping model that was used to decide on cellular EMT-status and estimate EMT-like changes. We confirmed that miR200c-mediated reversion of mesenchymal MDA-MB-231 cells is reflected by our EMT-phenotype model emphasizing its potential to predict the therapeutic efficacy of EMT-targeting drugs in the future.

PHLNs (polymeric lipid hybrid nanoparticles) are core–shell nanoparticle structures made up of polymer cores and lipid shells that have properties similar to both polymeric nanoparticles and liposomes. Methotrexate (MTX) loaded PLHNPs containing tween 80, phosphatidylcholine, poly D, L-lactic-co-glycolic acid (PLGA) & glyceryl tripalmitate prepared using solvent injection & homogenization method for glioblastoma treatment option. The MTX loaded PLHNPs optimized by Box–Behnken design to minimize particle size, higher entrapment efficacy, and maximize MTX concentration in the brain at 4h. The particle size, entrapment efficacy, concentration of drug in brain at 4h, zeta potential and AUC(Brain)/AUC(Plasma) ratio were in the range of 173.51-233.37nm, 70.56-86.34%, 6.38-12.38 μg/mL, 25.78-36.31mV & 1.02-5.32. in-vitro drug release studies, cellular internalization of optimized formulation against U-87 MG shows good anticancer effects.

Buildings can generate heats which are mostly generated from the machinery using inside the buildings, and these heats generally released to the atmosphere. Buildings can also block the wind flow by their canopies and trap the heat by using low albedo materials. These causes pointedly contribute to urban heat island and greenhouse effects. Likewise, urban development and building construction in Cambodia are growing rapidly. The construction has been recognized as a key development sector while thousands of buildings are being built and have been operated in the main cities. However, those buildings mostly have not been considered to incorporate sustainability concepts while the major final energy consumers in the country are buildings. The buildings’ energy consumption is also projected to increase more than double until 2040. Hence, sustainable building promotion in Cambodia is necessary, and sustainable building criteria are completely required. This research aims to find out significant sustainable building criteria for Cambodia and focused on planning and design criteria because having proper planning and design is a smart start leading to achieving building sustainability in all stages. This research used the Delphi methods to validate the relevant sustainable building criteria available in the literature and then select the significant ones for Cambodia based on the Delphi consensus. The results showed that ninety-nine consensus planning and design criteria were found to be significant for sustainable buildings in Cambodia.

Equiatomic CuZr alloy undergoes a martensitic transformation from the B2 parent phase to martensitic phases (P21/m and Cm) below 150 °C. We clarified the effect of the thermal cycling on the morphology and crystallography of martensite in equiatomic CuZr alloy using a transmission electron microscopy. The 10th cycled specimens consisted of different multiple structures at the maximum temperature of DSC measurement: 400 °C and 500°C, respectively. At the maximum temperature 400 °C of DSC measurement, it is composed of the fine plate-like variants, and a lamellar eutectoid structure consisting of Cu10Zr7 and CuZr2 phases on the martensitic variant. Concerning the maximum temperature 500 °C of DSC measurement, it is observed the martensitic structure and the lamellar structure in which the martensitic phase was completely eutectoid transformed. The formation of this lamellar eutectoid structure due to thermal cycling leads to the shift of forward and reverse transformation peaks to low and high temperature side. In addition, new forward and reverse transformation peaks indicating a new transformation appeared by thermal cycling, and the peaks remained around -20 °C. This new martensitic transformation behavior is also discussed.

In recent decades, widespread damage to structures due to destructive earthquakes has encouraged researchers to use seismic control systems. One of the most important structures is bridges, which should maintain their service after severe earthquakes. One of the ways to control the bridge is to isolation the deck from the substructure, which results in high displacements at different points in the bridge and the residual displacements within the separator itself, thus requiring repair and replacement of these systems after severe earthquakes. Therefore, the use of new seismic separation systems on bridges has always been important. The purpose of this project is to utilize a new memory-shaped seismic separator system to investigate the seismic performance of v-shaped column bridges , in which case the effect of earthquake orientation and its effects on responses the earthquake will also be assessed. Due to the ever-increasing advances in various intelligent materials, such as shape memory alloys, and their unique capacities, such as back-centering, and high fatigue and corrosion resistance, in this study, these materials have been used as a complementary component along with lead core separators. The shape memory alloy has been used as 4 vertical rods that connect two separating parts to each other and in this research the diameter and location of these rods will be calculated using optimization algorithm in Matlab software.

Single-level Principal Components Analysis (PCA) and multi-level PCA (mPCA) methods are applied here to a set of (2D frontal) facial images from a group of 80 Finnish subjects (34 male; 46 female) with two different facial expressions (smiling and neutral) per subject. Inspection of eigenvalues gives insight into the importance of different factors affecting shapes, including: biological sex, facial expression (neutral versus smiling), and all other variations. Biological sex and facial expression are shown to be reflected in those components at appropriate levels of the mPCA model. Dynamic 3D shape data for all phases of a smile made up a second dataset sampled from 60 adult British subjects (31 male; 29 female). Modes of variation reflected the act of smiling at the correct level of the mPCA model. Seven phases of the dynamic smiles are identified: rest pre-smile, onset 1 (acceleration), onset 2 (deceleration), apex, offset 1 (acceleration), offset 2 (deceleration), and rest post-smile. A clear cycle is observed in standardized scores at an appropriate level for mPCA and in single-level PCA. mPCA can be used to study static shapes and images, as well as dynamic changes in shape. It gave us much insight into the question “what’s in a smile?”

Additive manufacturing (3D printing) and computer-aided design (CAD) still have limited up-take in biomedical and bioengineering research and education, despite the significant potential of these technologies. The utility of organ-scale 3D-printed models of living structures is widely appreciated, while the workflows for microscopy data translation into tactile-accessible replicas are not well developed yet. Here, we demonstrate an accessible and reproducible CAD-based methodology for generating 3D-printed scalable models of human cells cultured in vitro and imaged using conventional scanning confocal microscopy and fused deposition modelling (FDM) 3D printing. We termed this technology CiTo-3DP (Cells-in-Touch for 3D Printing). As a proof-of-concept, we created CiTo-3DP models of human pancreatic cancer cells and healthy dermal fibroblasts by using selectively stained nuclei and the cytoskeleton components (f-actin and α-smooth muscle actin). The production of dismountable sets of cellular components was al-so shown. The CiTo-3DP approach can be adapted to comprehensively present various cell types, subcellular structures and extracellular matrices. We envisage that the resulting CAD and 3D printed models could be used for further applications, including but not limited to in silico simulations for biology, medicine, pharmacological research, tissue engineering, morphometrical analysis, multiphysics modelling, education, rehabilitation of visually impaired people, and integration into virtual reality.

Due to an increase in the number of image achieves, Content-Based Image Retrieval (CBIR) has gained attention for research community of computer vision. The image visual contents are represented in a feature space in the form of numerical values that is considered as a feature vector of image. Images belonging to different classes may contain the common visuals and shapes that can result in the closeness of computed feature space of two different images belonging to separate classes. Due to this reason, feature extraction and image representation is selected with appropriate features as it directly affects the performance of image retrieval system. The commonly used visual features are image spatial layout, color, texture and shape. Image feature space is combined to achieve the discriminating ability that is not possible to achieve when the features are used separately. Due to this reason, in this paper, we aim to explore the low-level feature combination that are based on color and shape features. We selected color moments and color histogram to represent color while shape is represented by using invariant moments. We selected this combination, as these features are reported intuitive, compact and robust for image representation. We evaluated the performance of our proposed research by using the Corel, Coil and Ground Truth (GT) image datasets. We evaluated the proposed low-level feature fusion by calculating the precision, recall and time required for feature extraction. The precision, recall and feature extraction values obtained from the proposed low-level feature fusion outperforms the existing research of CBIR.

This article attempts to propose a mathematical model and potential explanation regarding the unavoidable impact of a rigid body's peculiar shape on the seamless flow over it. The solid body completely immersed in a Newtonian fluid and respectively has a relative open circuit flow on it will typically experience various observable phenomena. These typical phenomena in laminar flow are explained using the proposed theory rather than conventional approximations or several partial theories. This article respectively represents an understanding of the laminar flow over a rigid body's external surface with due respect to its distinctive shape and size. To formulate a more realistic and simplified mathematical model for open circuit laminar flow over a body, a mathematical model is proposed based on the historical data of aerodynamics and theoretical mechanics. This mathematical model is intended to properly estimate forces on the continuous surface of the body in a laminar flow, to properly explain, understand and predict various phenomena like flow separation, flow transition, down-wash, stalling at the higher angle of attack, stalling velocity and how cambered airfoil can typically generate lift at a zero incidence angle. Most of all a mathematical model and the mechanism of streamline formation in an open-circuit laminar with respect to the shape and size of the body are illustrated.

We have an unprecedented ability to analyze and map the Earth’s surface, as deep learning technologies are applied to an abundance of Earth observation systems collecting images of the planet daily. In order to realize the potential of these data to improve conservation outcomes, simple, free, and effective methods are needed to enable a wide variety of stakeholders to derive actionable insights from these tools. In this paper we demonstrate simple methods and workflows using free, open computing resources to train well-studied convolutional neural networks and use these to delineate objects of interest in publicly available Earth observation images. With limited training datasets (<1000 observations), we used Google Earth Engine and Tensorflow to process Sentinel-2 and National Agricultural Imaging Program data, and use these to train U-Net and DeepLab models that delineate ground mounted solar arrays and parking lots in satellite imagery. The trained models achieved 81.5% intersection over union between predictions and ground-truth observations in validation images. These images were generated at different times and from different places from those upon which they were trained, indicating the ability of models to generalize outside of data on which they were trained. The two case studies we present illustrate how these methods can be used to inform and improve the development of renewable energy in a manner that is consistent with wildlife conservation.

Teeth segmentation plays a pivotal role in dental diagnosis, treatment, planning, and the development of computer-aided dental systems. It enables precise identification and analysis of dental structures, aiding in detecting dental abnormalities, measuring tooth dimensions, and assessing oral health conditions. Accurate teeth segmentation also facilitates the automation of dental workflows, leading to improved efficiency and reduced human error. Artificial Intelligence (AI) has witnessed rapid advancements, with various approaches developed or enhanced. While Convolutional Neural Networks (CNNs) have been widely used in medical image segmentation, the U-Net architecture has emerged as a standout performer due to its exceptional segmentation capabilities. This paper presents a proof of concept for the Attention U-Net architecture, as previously used in [1], applied to teeth segmentation. The study demonstrates the superior performance of this network in accurately segmenting teeth using a newly available benchmark dataset called Tufts Dental X-Ray Dataset. When trained and tested on 10-fold cross-validation, the model achieved an average dice coefficient of 95.01%, intersection over union of 90.6%, and pixel accuracy of 98.82%. These scores surpass those of all other networks implemented on the same dataset. By leveraging the Attention U-Net architecture, our research showcases the potential of advanced AI techniques in dental radiography. The findings contribute to the ongoing efforts to develop automated systems to assist dental professionals in their clinical practice.

We construct families of ground state representations of the U(1)-current net and of the Virasoro nets Vir_c with central charge c ≥ 1. We show that these representations are not covariant with respect to the original dilations, and those on the U(1)-current net are not solitonic. Furthermore, by going to the dual net of with respect to the ground state representations of Vir_c, one obtains possibly new family of Möbius covariant nets on S¹.

The aim of the study was to assess the relationship between the shape of the anterior-posterior curvature of the spine and body composition in school-children. The study included 257 children, aged 11-12. Correct spinal curvature was established in 106 (41.08%) subjects. Other types included: decreased kyphosis and correct lordosis - 40 participants (15.50%), correct kyphosis and decreased lordosis - 24 individuals (9.30%), increased kyphosis and correct lordosis - 17 subjects (6.59%), correct kyphosis and increased lordosis - 22 children (8.53%), decreased kyphosis and decreased lordosis - 32 people (12.40%), decreased kyphosis and increased lordosis - 4 of the examined subjects (1.55%), increased kyphosis and lordosis - 13 people (5.04%). In addition, 134 (51.94%) demonstrated scoliotic posture and 8 (3.10%) scoliosis. There were significant relationships between the shape of the anterior-posterior curvatures and body composition in school-children. Those with a strong body build (predominance of mesomorphs) were generally characterised by the correct formation of these curvatures. In contrast, lean people (with the predominance of ectomorphic factors) were more likely to experience abnormalities. No correlations with body composition were observed in the group with scoliotic posture or scoliosis.

In Europe, the recent application of regulations oriented to zero-energy buildings and climate neutrality in 2050 has led to a reduction in energy consumption for heating and cooling in the construction sector. The thermal insulation of the building envelope plays a key role in this process and the requirements about the maximum allowable thermal transmittance are defined by country-specific guidelines. Typically, high insulation values provide low energy consumption for heating, however, they may paradoxically imply the risk of overheating in summer period and thus negatively affect the overall performance of the building. In addition, the embodied energy and related emissions caused by the manufacturing and transportation processes of thermal insulation cannot be further neglected in the evaluation of the best optimal solution. Therefore, this paper aims to evaluate the influence in terms of embodied and operational energy of various walls’ thermal insulation thicknesses on residential buildings in Europe. To this end, the EnergyPlus engine was used for the energy simulation within Ladybug &amp; Honeybee tools, by parametrically conducting multiple iterations; 53 variations of external wall U-value, considering high and low thermal mass scenarios, were simulated for 100 reference cities of the European context, using a representative multifamily building as a reference. The results demonstrate that massive walls generally perform better than lightweight structures and, of course, the best solution in terms of energy varies according to each climate. The optimal values are graphically reported on the map of Europe according to specific climatic features, providing a guidance for new constructions and building retrofit.

Single-layer core corrugated sandwich panels generally consist of a corrugated core and two layers of panels, while multi-layer core corrugated sandwich panels are formed by stacking multiple layers of panels with multiple layers of core layers. In this study, integrated multilayer core corrugated sandwich panels with different shapes of corrugated cores (triangular, trapezoidal, and rectangular) and the different number of core layers were fabricated using 3D printing technology, and the mechanical behavior of such multilayer core corrugated sandwich panels under quasi-static three-point bending was investigated using experiments and numerical simulations. The effects of core shape and number of core layers on the bending deformation process, damage mode, load carrying capacity, and bending energy dissipation capacity of multilayer core sandwich panels are discussed. Parametric design of multilayer triangular core corrugated sandwich panels was also carried out by finite element software ABAQUS. It was found that a new multilayer corrugated sandwich panel with a multi-layer core is better than the single core shape multilayer corrugated sandwich panel in terms of bending load capacity, energy dissipation capacity and deformation capacity can be obtained through the combination design of different core shapes.

Pressure drop and flow pattern of oil-water flows were investigated in a 19 mm ID clear polyvinyl chloride pipe consisting of U-bend with radius of curvature of 100 mm. The range for oil and water superficial velocities tested were and respectively. Measurements were carried out under different flow conditions in a test section that consisted of four different parts: upstream of the bend, at the bend and at two redeveloping flow locations after the bend. The result indicated that the bend had limited influence on downstream flow patterns. However, the shear forces imposed by the bend caused some shift flow pattern transition and bubble characteristics in the redeveloping flow section after the bend relative to develop flow before the bend. Generally, pressure gradient at all the test sections increased with both oil fraction and water superficial velocity and there was a sharp change of pressure gradient profile during phase inversion. The transition point where phase inversion occurred was always within the range of . Pressure losses differed at the various test sections and the difference was strongly linked to the superficial velocity of the phases and the flow pattern. At high mixture velocity, pressure losses at the redeveloping section after the bend were higher than that at the bend and that for fully developed flows. At low mixture velocity, pressure losses at the bend are higher than in the straight sections. Pressure drop generally decreased with level of flow development downstream of the bend.

Recently, the demand for electric vehicle is increasing worldwide due to eco-friendly policies and stricter emission regulations. As a traction motor for electric vehicle, interior permanent magnet synchronous motors are mainly used. For the design of the interior permanent magnet synchronous motor, the magnetic equivalent circuit method, which is a method of lumped constant circuit, and the finite element method, which is a method of distributed constant circuit, mainly are used. Magnetic equivalent circuit method is useful for simple design through fast and intuitive parameters, but it cannot derive the distribution of magnetic field. The finite element method can derive an accurate magnetic field distribution, but it takes a long time to analyze and it is difficult to analyze intuitive design parameters. In this paper, magnetic equivalent circuit method and Carter coefficient are mixed for rotor structure design. This design method will be called the hybrid magnetic equivalent circuit method. Intuitive design parameters are derived through this hybrid magnetic equivalent circuit method. We will derive the Air gap flux density distribution according to rotor shape, no-load induced voltage, and cogging torque, and compare and verify it with the finite element method.

Landslide risk mitigation is limited by data scarcity. This could be improved using continuous landslide detection systems. In order to investigate which image types and machine learning (ML) models are most useful for landslide detection in a Norwegian setting, we compared the performance of five different ML models, for the Jølster case study (30-July-2019), in Western Norway. These included three globally pre-trained models; i) the Continuous Change Detection and Classification (CCDC) algorithm, ii) a combined k-means clustering and Random Forest classification model, and iii) a convolutional neural network (CNN), and two locally-trained models, including; iv) Classification and Regression Trees and v) a U-net CNN model. Images used included Sentinel-1, Sentinel-2, digital elevation model (DEM) and slope. The globally-trained models performed poorly in shadowed areas, and were all outperformed by the locally-trained models. A maximum Matthew’s correlation coefficient (MCC) score of 89% was achieved with model v, using combined Sentinel-1 and -2 images as input. This is one of the first attempts to apply deep-learning to detect landslides with both Sentinel-1 and -2 images. Using Sentinel-1 images only, the locally-trained deep-learning model significantly outperformed the conventional ML model. These findings contribute towards developing a national continuous monitoring system for landslides.

We show that the Einstein field equations for a five-dimensional warped spacetime, where only gravity can propagate into the bulk, determine the dynamical evolution of the warp factor of the four-dimensional brane spacetime. This can be explained as a holographic manifestation. The warped 5D model can be reformulated by considering the warp factor as a dilaton field ($\omega$) conformally coupled to gravity and embedded in a smooth $M_4 \otimes R$ manifold. On the brane, where the U(1) scalar-gauge fields live, the dilaton field manifests itself classically as a warp factor and enters the evolution equations for the metric components and matter fields. We write the Lagrangian for the Einstein-scalar-gauge fields in a conformal invariant setting. However, as expected, the conformal invariance is broken (trace-anomaly) by the appearance of a mass term and a quadratic term in the energy-momentum tensor of the scalar-gauge field, arising from the extrinsic curvature terms of the projected Einstein tensor. These terms can be interpreted as a constraint in order to maintain conformal invariance. By considering the dilaton field and Higgs field on equal footing on small scales, there will be no singular behavior, when $\omega\rightarrow 0$ and one can deduce constraints to maintain regularity of the action. Our conjecture is that $\omega$, alias warp factor, has a dual meaning. At very early times, when $\omega \rightarrow 0$, it describes the small-distance limit, while at later times it is a warp (or scale) factor that determines the dynamical evolution of the universe. We also present a numerical solution of the model and calculate the (time-dependent) trace-anomaly. The solution depends on the mass ratio of the scalar and gauge fields, the parameters of the model and the vortex charge $n$.

Abstract: Characterization the 3-D structure of clouds is needed for a more complete understanding of the Earth's radiative and latent heat fluxes. Here we develop and explore a “ray casting” algorithm applied to the Multi-angle Imaging SpectroRadiometer (MISR) on board the Terra satellite, to reconstruct 3-D cloud volumes for observed clouds. The ray casting algorithm is first applied to geometrically simple synthetic clouds to show that, under the assumption of perfect, clear-conservative cloud masks, the reconstruction method yields overestimation whose magnitude depends on the cloud geometry and the resolution of the reconstruction grid relative to the image pixel resolution. The method is then applied to two select MISR scenes, fully accounting for MISR’s viewing geometry for reconstructions over the Earth’s ellipsoidal surface. The MISR Radiometric Camera-by-camera Cloud Masks at 1.1 km resolution and custom cloud masks at 275 m resolution independently derived from MISR RGB channels are used as input cloud masks. A wind correction method, termed “cloud spreading”, is devised and applied to the cloud masks to offset potential cloud movements over short time intervals (around 7 minutes at maximum) between the cameras. The MISR cloud top height product is used as a constraint to reduce the overestimation at the cloud top. The reconstruction results show that their uncertainty is significant when the wind correction is applied, and that they have more refined structures when the input cloud mask has a higher resolution. Recommendations for improving the presented cloud volume reconstructions as well as for future passive remote sensing satellite missions are discussed.

In this paper, a resonant system that produces a movement of low amplitude and ultrasonic frequency is used to achieve the vibration assistance in a ball-burnishing process. A full vibration characterization of this process performed in a lathe was done. It is carried out by a new tool designed in the research group of the authors. Its purpose is to demonstrate that the machine and the tool do not have any resonance problem during the process and to prevent possible failures. The analysis of this dynamic behaviour permits to validate the suitability of the tool when it is anchored to a numerical control lathe. This is very important for its future industrial implementation. It is also intended to confirm that the system adequately transmits vibrations through the material. To do this, a methodology to validate the dynamic tool behaviour was developed. Several techniques that combine the usual and ultrasonic vibration ranges through static and dynamic measurements were merged: vibration and acoustic emission measurements. An operational deflection shape (ODS) exercise has been also performed. Results show the suitability of the tool used to transmit the assistance vibrations, and that no damage is produced in the material in any case.

This article addresses the question why initiatives in the field of green business and sustainable development often fail. Therefore, it dismantles some typical patterns of failure and shows – as a case study – how these patterns can be challenged through an innovative educational concept: the green business and sustainable development school. The applied methodology is a real-life project that is designed through blended, interdisciplinary elements from business model canvas, Theory U, participation and design thinking. The results of the school initiative are discussed and evaluated by four distinctive stakeholder groups and outline the school’s supporting potential to overcome typical patterns of failure by the younger generation in the future. This article concludes with ideas to enhance the school concept reaching out to even more stakeholder-groups to increase its reliability and viability.

The common dandelion uses a bundle of drag-enhancing bristles (the pappus) that enables seed dispersal over formidable distances; however, the scaling laws of aerodynamic drag underpinning pappus-mediated flight remains unresolved. In this paper, we study the aerodynamic shape of dandelion, derive the scaling law of resistance, determine the Vogel exponent. In particular, we find that the total drag coefficient is proportional to the -2/3 power of the dandelion pappus Reynolds number, and obtain the terminal velocity of the dandelion seed under gravitation field.

Detailed mapping and structural observations on the Cycladic Blueschist Unit (CBU) of Iraklia island integrated by detrital zircon (DZ) U-Pb ages elucidate the Mesozoic pre-subduction evolution and the Cenozoic orogenic events. Field data reveal that the Iraklia tectonostratigraphy includes a heterogeneous Lower Schist Unit juxtaposed against a Variegated Marble Unit and an overlying Upper Schist Unit. The contact is an extensional ductile-to-brittle-ductile, top-to-N shear zone, associated with the Oligo-Miocene exhumation. The DZ spectrum of the Lower Schist Unit characterized by Gondwanan/peri-Gondwanan provenance signatures points to Late Triassic maximum depositional ages (MDAs). A quartz-rich schist layer yielded Precambrian DZ ages exclusively, considered part of the pre-Variscan metasedimentary Cycladic Basement, equivalent to those observed on Ios island. A significant change occurred during the deposition of the Upper Schist Unit, revealing Late Cretaceous MDAs and a high amount of Late Paleozoic DZ ages, attesting to more internal Pelagonian source areas. The imprint of Paleotethyan vs. Neotethyan geodynamic events is revealed in the DZ U-Pb ages record. The Triassic DZ input demonstrates eroded volcanic material related to the final Paleotethys closure and the Pindos/CBU rift basin opening. Late Cretaceous metamorphic/magmatic zircons and ~48-56 Ma zircon rims constrain the onset of subduction and high-pressure metamorphism.

The genetic code evolved around the reading of the tRNA anticodon on the primitive ribosome, and tRNA-34 wobble and tRNA-37 modifications coevolved with the code. We posit that EF-Tu, the closing mechanism of the 30S ribosomal subunit, methylation of wobble U34 at the 5-carbon and suppression of wobbling at the tRNA-36 position were partly redundant and overlapping functions that coevolved to establish the code. The genetic code devolved in evolution of mitochondria to reduce the size of the tRNAome (all of the tRNAs of an organism or organelle). “Superwobbling” or four-way wobbling describes a major mechanism for shrinking the mitochondrial tRNAome. In superwobbling, unmodified wobble tRNA-U34 can recognize all four codon wobble bases (A, G, C and U), allowing a single unmodified tRNA-U34 to read a 4-codon box. During code evolution, to suppress superwobbling in 2-codon sectors, U34 modification by methylation at the 5-carbon position appears essential. As expected, at the base of code evolution, tRNA-37 modifications mostly related to the identity of the adjacent tRNA-36 base. TRNA-37 modifications help maintain the translation frame during elongation.

Ustilago maydis, member of the Ustilaginaceae family, is a promising host for the production of several metabolites including itaconic acid. This dicarboxylate has great potential as a bio-based building block in the polymer industry, and is of special interest for pharmaceutical applications. Several itaconate overproducing Ustilago strains have been generated by metabolic and morphology engineering. This yielded stabilized unicellular morphology through fuz7 deletion, reduction of by-product formation through deletion of genes responsible for itaconate oxidation and (glyco)lipid production, and the overexpression of the regulator of the itaconate cluster ria1 and the mitochondrial tricarboxylate transporter encoded by mttA from Aspergillus terreus. In this study, itaconate production was further optimized by consolidating these different optimizations into one strain. The combined modifications resulted in itaconic acid production at theoretical maximal yield, which was achieved under biotechnologically relevant fed-batch fermentations with continuous feed.

Ampelography, the botanical discipline dedicated to the identification and classification of grapevine cultivars, was grounded on the description of morphological characters and more recently is based on the application of DNA polymorphisms. New methods of image analysis may help to optimize morphological approaches in ampelography. The objective of this study was the classification of representative cultivars of Vitis vinifera conserved in the Spanish collection of IMIDRA according to seed shape. Thirty eight cultivars representing the diversity of this collection were analyzed. A consensus seed silhouette was defined for each cultivar representing the geometric figure that better adjusted to their seed shape. All the cultivars tested were classified in ten morphological groups, each corresponding to a new model. The models are geometric figures defined by equations and similarity to each model is evaluated by quantification of percent of the area shared by the two figures, the seed and the model (J index). The comparison of seed images with geometric models is a rapid and convenient method to classify cultivars. A large proportion of the collection may be classified according to the new models described and the method permits to find new models according to seed shape in other cultivars.

In thermal friction drilling (TFD) operations, the geometrical dimensions of bushing shape, height and wall thickness are the most vital consequences, due to increasing the connecting length and strength. In this paper, AA7075-T651 aluminum alloys with 2, 4, 6, 8, and 10 mm in thicknesses were drilled with TFD process in order to investigate the density, the volume ratio, and height and wall thickness of the bushings. The experiments were conducted at constant spindle speed and feed rate conditions by using HSS conical tools of 5, 10, 15, and 20 mm in diameters. It was experimentally found that the bushing height and the wall thickness were tendency of increase linearly with increasing both material thickness and tool diameter. The effect of tool diameter was found to have much of influence on the measured values than the thickness of the drilled material. The density of the bushing was changed inconsiderably. Approximately 70-75 % percentages of the evacuated material composed the bushing shape, in TFD operations.

Semi-destructive and non-destructive techniques are not commonly used for masonry as they are complex and difficult to perform. This paper describes validation of the following methods: semi-destructive and non-destructive, ultrasonic technique for autoclaved aerated concrete (AAC). The research subject was the compressive strength of AAC test elements with declared various density classes of: 400, 500, 600 and 700 (kg/m3) and various moisture levels. Empirical data including the shape and size of specimens, were established from tests on 494 cylindrical and cuboid specimens, and standard cube specimens 100×100×100 mm using the general relationship for standard concrete (Neville’s curve). The effect of moisture on AAC was taken into account while determining the strength fBw for 127 standard specimens tested at different levels of water content (w = 100%, 67%, 33% 23% and 10%). Defined empirical relations can be used to correct the compressive strength of dry specimens. For 91 specimens 100×100×100 mm, the P-wave velocity cp was tested with the transmission method using using the ultrasonic pulse velocity method with exponential transducers. The curve (fBw – cp) for determining the compressive strength of AAC elements with any moisture level (fBw) was established.

Static standing postural stability has been measured by multiscale entropy (MSE), which is used to measure complexity. In this study, we used the average entropy (AE) to measure the static standing postural stability, as AE is a good measure of disorder. The center of pressure (COP) trajectories were collected from 11 subjects under four kinds of balance situation, from stable to unstable: bipedal with open eyes, bipedal with closed eyes, unipedal with open eyes, and unipedal with closed eyes. The AE, entropy of entropy (EoE), and MSE methods were used to analyze these COP data, and EoE was found to be a good measure of complexity. The AE of the 11 subjects sequentially increased by 100%as the balance situations progressed from stable to unstable, but the results of EoE and MSE did not follow this trend. Therefore, AE, rather than EoE or MSE, is a good measure of static standing postural stability. Furthermore, the comparison of EoE and AE plots exhibited an inverted U curve, which is another example of a complexity versus disorder inverted U curve.

The lordosis of the haemal part of the vertebral column is a frequent abnormality in reared fish. Haemal lordosis develops during the late larval and early juvenile period, mainly due to the high swimming activity of the fish in the rearing tanks. In the present study we examined whether haemal lordosis recovers during the growth of European sea bass. Furthermore, we aimed to develop simple morphometric indices (PrAn1 and PrAn2) that could link the severity of lordosis at the juvenile stage with fish morphological quality at harvesting. At 111 days post-hatching (dph, 53±4 mm standard length, SL), 600 seabass juveniles with lordotic (L, 200 fish) or normal (N, 400 fish) external morphology were selected and introduced in a common tank. At 150 dph (75±7 mm SL), 350 fish were randomly selected, pit-tagged and transferred in a sea cage for on-growing up to 502 dph (234±16 mm SL). The morphological examination of the fish at 150 and 502 dph revealed that the 60% (46 out of 77) of L juveniles turned into normal phenotype by the end of on-growing period. Interestingly, 56% of the fish with recovered external morphology (N-Rec) presented either a completely normal vertebral column (31%) or minor abnormalities of individual vertebrae (25%). Following the results of geometric morphometric analysis, the differences in the body shape between N-Rec and N fish were not significant (p&gt;0.05, canonical variate analysis). The examined morphometric indices were effective in discriminating the normal fish from the 58% (PrAn1) to 65% (PrAn2) of lordotic juveniles. Results are discussed with respect to the mechanism of lordosis recovery, as well as to their application for the quality control and cull out of the abnormal fish in the commercial hatcheries.

The article proposes an indirect measurement method based on a dimensional and shape analysis of forgings for the evaluation of the manufacture and the proper operation of the key elements of the crank press, in which after modernization, a quick tool assembly based on SMED (Single Minute Exchange of Die) was implemented. As a result of the introduced changes aiming at improving the forging aggregate and increasing the production efficiency, errors were observed on the manufactured products-forgings in the form of twists and joggles. The preliminary analysis showed that they can be clearances and dynamic deformation in the kinematic chain, the occurrence of side forces during automatic forging of the forging in a two-component system (a long, thin element), as well as the design and construction errors in the joining of the SMED instrument with the table tops of the press. In order to solve the presented problem, in the first place, a separate dimensional and shape analysis was made of selected elements of the press and the instrumentation with the use of the 3D scanning method with the purpose to analyze the construction tolerances of the key elements of the press geometry. Next, an evaluation of the effect of clearances and dynamic deformations of the press as well as the force distribution during the forging process was made through numerical modelling. Despite all of the above, such an approach did not make it possible to solve the problem. A proprietary method with the use of 3d reverse scanning was proposed, which allowed to solve the problem of forgings errors. Based on the measurement results and analyses for a few variants of production cycles the necessary changes was obtained, making it possible to minimize the errors and obtain proper products in respect of geometry and quality.

The design flood concept (DF) provides for an essential tool in designing the hydraulic works, in defining the reservoir operation programs and for a reliable flood hazard identification. Under a simplified approach, the maximum discharge and the floods volume are statistically processed to reasonably define the DF. Yet, the integral hydrograph provides additional key temporal and quantitative details of important significance for flood management and particularly for the res-ervoirs operation and associated risks of failures. The procedure presented in this paper (as applied on a set of compatibly shaped hydrographs) involves the following key stages: (i) normalize the floods, (ii) define similar flood shape classes and (iii) evaluate the average dimensionless flood (ADF) for each class. The ADFs are finally transformed into a set of (DF)s. Many statistical distributions approximate acceptably the frequent values of the maximum discharges or the flood volumes, yet displaying a significant spread for medium or rare probabilities of exceedance (PE). This scattering, which can be explained by the epistemic uncertainty, defines an area of uncertainty both for measured and extrapolated values. In considering upper and lower values of the uncertainty in-tervals as limits for maximum discharges and flood volumes, then by combining them compatibly, a set of DFs - as completely defined hydrographs, with different shapes - results for each PE. The herein proposed procedure defines both one peak DF and multi-peaks DF. Subsequently, such DFs do assist water managers in examining and establishing tailored approaches for a variety of input hydrographs. Among the DFs that would correspond to a same PE, the most compact floods arise a special interest, for they are basic in defining the set of safe operation rules for hydraulic structures.

This paper reports on a series of dynamic simple shear tests conducted to investigate the influence of particle shape on the damping ratio of dry sand. The tests were conducted on sand samples subjected to simple cyclic shear tests to evaluate their cyclic behavior. The particle shape was quantified using three shape parameters: roundness, sphericity, and regularity. The sand samples were subjected to twelve different scenarios with varying vertical stresses and cyclic stress ratios (CSR), in both constant and controlled stress states. Each scenario involved five cyclic tests, using the same sand that was reconstructed from its previous cyclic test. After each cyclic test, hysteresis loops were created to determine the damping ratio. The results showed that the shape of the sand particles changed during cyclic loading, becoming more rounded and spherical, which resulted in an increase in damping ratio. Moreover, the paper presents two artificial intelligence models, an artificial neural network (ANN) and a support vector machine (SVM), which were developed to predict the effect of grain shape on the damping ratio. The models were found to be effective in predicting the damping ratio based on the shape of the grain, vertical stress, CSR, and number of loading cycles. Furthermore, a parameter analysis was conducted to identify the most important shape parameter, which was found to be vertical stress and regularity, while parameter CSR was the least important. Overall, this study contributes to a better understanding of the relationship between particle shape and damping ratio, which could have practical implications for geotechnical engineering applications.

Shape Memory Polymer (SMP) actuators are smart materials that adapt and switch shape in response to environmental conditions, allowing controlled and dynamic building systems. The integrated SMP strip enabled the adaptive facade shading system to operate independently and with flexibility under certain thermoresponsive conditions to regulate building performance. This study aims to improve adaptive façade performance in a hot-humid climate by determining optimal thermal activation factors for the shape memory polymer. This was achieved by comprehensively examining and analysing the impact of various SMP activation parameters on energy efficiency, thermal comfort, and visual comfort. In addition, dynamic IES-VE building energy simulation was used to evaluate the thermal performance of the adaptable facade. The results were validated using a multicriteria approach to compare with the existing glass façade of a high-rise apartment. The results showed that the coactivation technique, which combines solar radiation and air temperature triggers, proved to be the most efficient strategy to improve the performance of the adaptive façade. This strategy minimised heat gain, lowered indoor temperatures, reduced glare, and enhanced daylight comfort, resulting in notable energy savings through reduced cooling consumption. The study concluded that the utilisation of SMP actuators with fine-tuning activation parameters significantly optimised adaptive façade performance, promoting functionality, efficiency, and sustainability in buildings.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Schistosomiasis is a debilitating parasitic disease of poverty that affects more than 200 million people worldwide, mostly in sub-Saharan Africa, and is clearly associated with the construction of dams and water resource management infrastructure in tropical and subtropical areas. Changes to hydrology and salinity linked to water infrastructure development may create conditions favorable to the aquatic vegetation that is suitable habitat for the intermediate snail hosts of schistosome parasites. With thousands of small and large water reservoirs, irrigation canals, and dams developed or under construction in Africa, it is crucial to accurately assess the spatial distribution of high-risk environments that are habitat for freshwater snail intermediate hosts of schistosomiasis in rapidly changing ecosystems. Yet, standard techniques for monitoring snails are labor-intensive, time-consuming, and provide information limited to the small areas that can be manually sampled. Consequently, in low-income countries where schistosomiasis control is most needed, there are formidable challenges to identify potential transmission hotspots for targeted medical and environmental interventions. In this study, we developed a new framework to map the spatial distribution of suitable snail habitat across large spatial scales in the Senegal River Basin by integrating satellite data, high-definition, low-cost drone imagery, and an artificial intelligence (AI)-powered computer vision technique called semantic segmentation. A deep learning model (U-Net) was built to automatically analyze high-resolution satellite imagery to produce segmentation maps of aquatic vegetation, with a fast and robust generalized prediction that proved more accurate than a more commonly used random forest approach. Accurate and up-to-date knowledge of areas at highest risk for disease transmission can increase the effectiveness of control interventions by targeting habitat of disease-carrying snails. With the deployment of this new framework, local governments or health actors might better target environmental interventions to where and when they are most needed in an integrated effort to reach the goal of schistosomiasis elimination.

AbstractThis work deals with aerofoil aerodynamic features optimization, not only to improve flight features, but also to improve economy, ecology and safety of parameters of flight technique.In cruise mission, occupying the most flight time, the most important parameter is aerodynamic drag, which directly influences the aeroplane operational economy of transportation. Drag reduction is adequately reflected in the fuel consumption reduction. Consumption reduction is also adequately reflected in the flight ecology. In take-off and landing mission, the safety is priority and directly influences the aerofoil geometry.For cruise mission the new modified evolutionary algorithms (EA) are used to parameters incoming to Bezier-PARSEC 3434 parametrization. Such aerofoil is processed and evaluated by the Xfoil program. The change of model parameters results to optimal aerofoil shape.The DCAG (Direct Control Aerofoil Geometry) is unique developed mechanical device, makes possible the change of curvature of aerofoil, and also aerofoil geometry. DCAG is based on the rotary principle, which makes it possible to define the curvature of aerofoil for every roll as well as defining the geometry in the variable parts of aerofoil.For take-off and landing mission the best combination of slots and flaps is choosed. To improve of laminarity and reduce turbulent flow the DCAG is used.The work results to optimization, which is 50 times faster in comparison to ordinary optimization, with minimum of input parameters (flight speed, chord length, range of angles of attack and fitness function).The optimized aerofoil can achieve savings in fuel consumption up to 44% in comparison with unoptimized aerofoil, the aerodynamic drag reduction up to 44%.The output was checked by ANSYS Fluent simulation.

Thermal shape memory polymers (SMPs) find increasing applications in biology and medicine due to their promising potential for improved biocompatibility. In such applications, the inevitable penetration of small molecules from the ambient fluid into the polymer influences the shape recovery process and often leads to a reduction of the temperature, at which shape recovery takes place. We show here via molecular dynamics simulations that the size of additive molecules plays a key role for this process. While the effect of concentration on the recovery rate is monotonic in the investigated range, a non-monotonic dependence on the size of additive molecules emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for switching the recovery process in polymer-based shape memory materials.

In this paper, we investigate some elementary properties of two kinds modified Szasz type basis functions, depending on non-negative parameters. We study some shape preserving properties of these operators concerning monotonicity, convexity, starlikeness, semi-additivity and smoothness.

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Liquid crystal elastomers (LCEs) are shape morphing materials whose large and reversible shape transformation results from the coupling between the mobile anisotropic properties of liquid crystal (LC) units and the rubber elastic of polymer networks. Their shape changing behaviors under the stimuli are largely directed by LC orientations, and therefore various strategies have been developed to spatially modulate the LC alignments. But most of the methods suffer from complex fabrication technologies or intrinsic limitations in applicability. To address this issue, programmable complex shape changes in some types of LCEs, such as polysiloxane side-chain LCEs or thiol-acrylate main-chain LCEs, etc, have been achieved by using a mechanical alignment programming process coupled with two-step crosslinking. Here, we report a polysiloxane main-chain LCE with programmable 2D and 3D shape changing performances achieved by mechanically programming the polydomain LCE between the two crosslinking steps. The resulting LCEs exhibited reversible thermal induced shape transformation between the initial and programmed shapes due to the two-way memory between the first network structure and the second network structure. Our work would be potential for expanding the applications of LCE materials in actuators, soft robotics and smart structures where arbitrary and easily programmed shape morphings are needed.

The study of a flexible body immersed in a flowing medium is one of best way to find its aerodynamic shape. This Letter revisited the problem first studied by Alben, Shelley and Zhang (Nature 420, 479-481, 2002). The aerodynamic shape of the fibre is found by simpler approach and universal drag scaling laws of the flexible fibre in flowing medium are proposed by using dimensional analysis. The Alben scaling laws is being generalized and confirmed to be universal. Our study show that the Alben number is a measurement of maximum curvature of the fibre forced by dynamic pressure. A complete Maple code is provided for finding aerodynamic shape of the fibre in the flowing medium.

The results of an LA-ICP-MS U-Pb dating and Hf isotope study of zircon crystals separated from small eclogite xenoliths found in Devonian kimberlites within the Prypyat horst, Ukraine, are reported. The studied area is located in the Central Belarusian Suture Zone, which represents a Paleoproterozoic belt extending along the boundary between the Sarmatian and Fennoscandian segments of the East European Platform. Four laser ablation sites on two zircon grains yielded Paleoproterozoic U-Pb ages between 1954 ± 24 Ma and 1735 ± 54 Ma. In contrast, three of four Hf sites revealed negative εHf values and Paleoarchean to Mesoarchean model ages, excluding the possibility that the eclogite xenoliths represent segments of a Paleoproterozoic subducted slab or younger mafic melts crystallized in the subcontinental lithospheric mantle. A single laser ablation Hf spot yielded a positive εHf value (+3) and a Paleoproterozoic model age. Two models for eclogite origin can be proposed. The first foresees the extension of the Archean lower-crustal or lithospheric roots beneath the Central Belarus Suture Zone for over 200 km from the nearest known outcrop of Archean rocks. The second model is that the Central Belarus Suture Zone represents a rifted-out fragment of the Kola-Karelian craton that was accreted to Sarmatia before the actual collision of these two segments of Baltica.

Shape-memory hydrogels (SMH) are as multifunctional, actively-moving polymers of interest in biomedicine. In loosely crosslinked polymer networks gelatin chains may form triple helices, which can act as temporary netpoints in SMH, depending on the presence of salts. Here, we show programming and initiation of the shape-memory effect of such networks based on a thermomechanical process compatible with the physiological environment. The SMH were synthesized by reaction of glycidylmethacrylated gelatin with OEG α,ω-dithiols of varying crosslinker length and amount. Triple helicalization of gelatin chains is shown directly by wide-angle X-ray scattering and indirectly via the mechanical behavior at different temperatures. The ability to form triple helices increased with the molar mass of the crosslinker. Hydrogels had storage moduli of 0.27-23 kPa and Young’s moduli of 215-360 kPa at 4 °C. The hydrogels were hydrolytically degradable, with full degradation to water soluble products within one week at 37 °C and pH = 7.4. A thermally-induced shape-memory effect is demonstrated in bending as well as in compression tests, in which shape recovery with excellent shape recovery rates Rr close to 100% were observed. In the future, the material presented here could be applied e.g. as self-anchoring devices mechanically resembling the extracellular matrix.

This paper presents an investigation into the influence of drag-reducing polymer (DRP) on the flow of water inside and around U-bends. The DRPs tested were partially hydrolysed polyacrylamide (HPAM) and two different molecular weight polyethylene oxides (PEO). The Reynolds number and in-situ concentration ranges of water and DRP were and respectively. The test section was made up of clear polyvinyl chloride (CPVC) pipes that contained two U-bends with radii of curvature (R) of 100 and 200 mm as well as straight sections of 19-mm ID. Higher pressure gradient was recorded in the under-developed flow section after the bend. Drag reduction (DR) increased with in-situ concentration of the DRP and the flowrate up to some threshold values. The concentration and flowrate thresholds were about 20 ppm and 1.07 m/s respectively. DR differed among the different sections considered with the highest values recorded for developed flows upstream of the bend and the least values recorded in the bend. DR at station 1 (immediately after the bend) was generally lower than that at station 2 (further downstream). P-K Plots showed that, the DR envelop for developed flow in straight pipes did not apply to the bend and the under-developed flow section. DR increased with polymer molecular weight and ionic strength in straight sections. However, molecular weight (and polymer shearing) had limited effect on DR in the bends. DR characteristics at the bend suggested that there was a different or additional mechanism. The effect of bend curvature ratio on DR was predominant after the U-bend. The larger the ratio of pipe diameter to bend diameter, the lower the DR in the redeveloping sections after the bend. For R = 100 mm, the highest DR recorded for fully developed flows before bend, in the bend, at stations 1 and 2 were 57, 31, 36 and 33% respectively while that for R = 200 mm were 64, 28, 42 and 49% respectively.

Background: The papaya mosaic virus (PapMV) vaccine platform is a rod-shape nanoparticle made of the recombinant PapMV coat protein (CP) self-assembled around a non-coding ssRNA template. The PapMV nanoparticle induces innate immunity through stimulation of the toll-like receptors (TLR) 7 and 8. The display of the vaccine antigen at the surface of the nanoparticle, associated with the co-stimulation signal via TLR7/8, ensures a strong stimulation of the immune response, which is ideal for the development of candidate vaccines. In this study, we assess the impact of where the peptide antigen is fused, either at the surface or at the extremities of the nanoparticles, on the immune response directed to that antigen. Methods: Two different peptides from influenza A virus were used as model antigens. The conserved M2e peptide was chosen as the B-cell epitope, and a peptide derived from the nucleocapsid was chosen as the CTL epitope. These peptides were coupled at two different positions on the PapMV CP, the N- (PapMV-N) or the C-terminus (PapMV-C) using the transpeptidase activity of Sortase A (SrtA). The immune responses, both humoral and CD8+ T cell-mediated, directed to the peptide antigens in the two different fusion contexts were analyzed and compared. The impact of coupling density at the surface of the nanoparticle was also investigated. Conclusions: The results demonstrate that coupling of the peptide antigens at the N-terminus (PapMV-N) of the PapMV CP led to an enhanced immune response to the coupled peptide antigens as compared to coupling to the C-terminus. The difference between the two vaccine platforms is linked to the enhanced capacity of the PapMV-N vaccine platform to stimulate the TLR7/8. We also demonstrated that the strength of the immune response increases with the density of coupling at the surface of the nanoparticles.

The wave-particle description of quantum mechanics is briefly reviewed to set an analogy between the quantum mechanics of particles and fields and quantum cosmology. It is shown that quantum cosmology can be seen as a quantum field theory developed in the space of three metrics (the metrics of the spatial sections of the spacetime), where the classical evolution of the universe corresponds to a definite trajectory and the quantum mechanics of matter fields emerges as the first order quantum correction. Like in a quantum field theory developed in an isotropic background, the universes are created in universe-antiuniverse pairs, which might provide us with an explanation for the matter-antimatter asymmetry observed in our universe without going beyond the standard model. Moreover, the states of the matter and the antimatter fields of the pair of universes are entangled and that makes that their initial states are in a non-vacuum state (presumably in a thermal state). That might open the possibility of looking for observable imprints of the creation of universes in pairs is the astronomical data.

Symmetry in biological and physical systems is a product of self-organization driven by evolutionary processes, or mechanical systems under constraints. Symmetry-based feature extraction or representation by neural networks may unravel the most informative contents in large image databases. Despite significant achievements of artificial intelligence in recognition and classification of regular patterns, the problem of uncertainty remains a major challenge in ambiguous data. In this study, we present an artificial neural network that detects symmetry uncertainty states in human observers. To this end, we exploit a neural network metric in the output of a biologically inspired Self-Organizing Map, the Quantization Error (SOM-QE). Shape pairs with perfect geometric mirror symmetry but a non-homogenous appearance, caused by local variations in hue, saturation, or lightness within and/or across the shapes in a given pair produce, as shown here, longer choice RT for ‘yes’ responses relative to symmetry. These data are consistently mirrored by the variations in the SOM-QE from unsupervised neural network analysis of the same stimulus images. The neural network metric is thus capable of detecting and scaling human symmetry uncertainty in response to patterns. Such capacity is tightly linked to the metric’s proven selectivity to local contrast and color variations in large and highly complex image data.

Recently we started the development of Holographic Dendrogramic Theory (DH-theory). It is based on the novel mathematical representation of the relational event universe (in the spirit of (Smolin, Barbour, Rovelli). Elementary events are represented by branches of dendrograms, finite trees, which are generated from data with clustering algorithms. In this note we study the dynamics of the event-universe generated by the appearance of a new event. Generally, each new event can generate the complete reconstruction of the whole dendrogramic universe. However, we found (via numerical simulation) unexpected stability of this universe. Its events are coupled via the hierarchic relational structure which is relatively stable with respect even random generation of new events. We also observe the regularity patterns in location of new events on dendrograms. In the curse of evolution, the dendrogram’s complexity increases and determine the arrow of time the event universe. We use the complexity measure from particle shape dynamics which was shown to be increase in both direction away from a Janus point and thus determine the arrow of time in symmetrical manner away from a Janus point. The particle shape dynamics theory is a relational theory with close ideological resemblance to DH-theory as both relays on Mach’s principle and Leibniz’s relationalism and his principles. By using the complexity measure on dendrograms and its p-adic string representation, we demonstrate the emergence of time arrow from the p-adic zero-dimensional field, where space and time are absent.

We present here seven new zircon (U-Th)/He (ZHe) ages and three new zircon fission track ages (ZFT) analyzed from an age-elevation profile (Machu Picchu, Peru). ZFT data present older ages in comparison with the other thermochronological data, whereas the ZHe data interestingly present similar ages than the ones obtained with apatite (U-Th)/He (AHe). It has been proposed that He retention in zircon is linked to the damage dose, with an evolution of the closure-temperature from low values associated to low α-dose (<1016 α/g), subsequently increasing before decreasing again at very high α-dose (>1018 α /g). Studies have been focused on the He diffusion behavior at high α-dose, but little is known at low dose. We propose that the ZHe closure temperature at α-dose ranging from 0.6×1015 to 4×1016 α/g is in the range of ~60-80°C. This value is lower than the one proposed in the current damage model ZRDAAM and demonstrates that the ZHe and AHe methods could have similar closure temperatures at low α-dose (i.e. similar ages). These new data strengthen our previous geological conclusions and even highlight an about twice more important cooling rate than the one deduced from AHe and apatite fission-track data alone registered at Machu Picchu.

Heusler Ni-Mn-Ga alloys with martensitic transformation being multiferroic materials are touted for magneto- and multi-caloric effect (MCE) and moreover, they exhibit magnetic shape memory (MSM) phenomena. MCE benefits from high saturation magnetization and also large variability and sensitivity of transformation temperatures on alloying. In contrast, MSM phenomena are limited by low temperatures of both ferromagnetic and ferroelastic transformations. In an attempt to increase the transformation temperatures and to understand the physical fundamentals beyond transformation variations and magnetic ordering, we experimentally investigate the magnetic and transformation properties in Ni2MnGa alloyed with transitional elements spanning from Cr to Cu. These elements are consecutively substituted on Ni, Mn, and Ga sites, to establish the effect of positional substitution and elemental evolution. The elemental dependence of saturation magnetization, magnetocrystalline anisotropy, Curie temperature, and martensitic transformation temperatures are compared with (non-)stoichiometric Ni-Mn-Ga Heusler compounds. The observed behavior is complex and there are no clear trends of transformation temperatures as a function of the number of valence (non-bonding) electrons per atom, however, the saturation magnetization at 10K and Curie temperature seems to follow the Pauli-Slater curve. Obtained results can serve as useful rectification for the theoretical prediction of new Ni-Mn-Ga-X Heusler alloys.

Space vehicles may be propelled by solar sails exploiting the radiation pressure coming from the sun and applied on their surfaces. This work deals with the adoption of Shape-Memory Alloy (SMA) elements in the sail deployment mechanism activated by the Joule Effect, i.e. using the same SMA elements as a resistance within suitable designed electrical circuits. Mathematical models were analyzed for the thermal analysis by implementing algorithms for the evaluation of the temperature trend depending on the design parameters. Several solar sail prototypes were built up and tested with different number, size and arrangement of the SMA elements, as well as the type of the selected electrical circuit. The main parameters have been discussed in the tested configurations and advantages discussed as well.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

The Multi-Level Model (=MLM) was suggested by A. Levichev as a description of quarks and gluons. The review recalls MLM-terminology while MLM-findings (for quarks and leptons) are compared to the theoretical and experimental data as accepted by the Standard Model (=SM). MLM is based on Segal’s compact space-time U(2) and on the sequence of embeddings: U(2) into U(3), U(2) into U(4), etc. These groups were called the levels (of matter): U(2) - the 0th (that is, our mundane world), U(3) - the 1st, U(4) - the 2nd, etc. Such a convention matches the SM-quarks' generations list. Each SM-quark is viewed either as a sunken proton, or as a captured proton. The MLM-proton is elementary and indestructible (hence no need for confinement). For MLM-quarks, in terms of the notion of a ruling group, flavor and color are defined mathematically. The number of colors (and of flavors) is level-dependent. For levels U(3) through U(6) the correspondence with the SM-quarks is established. Three new quarks and two new leptons are predicted. The SM-puzzle of quark and lepton generations is solved. Using the Han-Nambu scheme, the notion of the quark’s electric charge is expressed in terms of color charges. The original part of the review suggests studying the proton’s properties (like mass, shape and inner pressure) on the ba-sis of its wave function.

The automatic diagnosis of cardiovascular diseases has received much attention in the deep learning field. In this context, the segmentation of the left ventricle endocardium constitutes a major task in diagnosing heart conditions such as health failure and hypertrophic cardiomyopathy. The objective of this paper is to propose a "deep convolution network" for segmenting the internal cavity of the left ventricle (endocardium) using MRI images. In particular, we design an improved UNET model which handles additional inception modules for efficiently segmenting the internal cavity of the left ventricle. Our approach has been validated on the Sunnybrook Cardiac Data (SCD) dataset and has showed promising results in terms of precision. More specifically, the improved UNET largely outperforms the baseline UNET model and many existing state-of-the-art methods.

This paper develops the mathematical modeling and deflection control of a textile-reinforced composite integrated with shape memory actuators. The model of the system is derived using identification method and unstructured uncertainty approach. Based on this model and robust stability analysis a robust proportional-integral controller is designed for controlling the deflection of the composite. The performance of the proposed controller is compared with a classical one through experimental analysis.

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

The environmental disaster in Kamchatka in the autumn of 2020 was caused by an extensive bloom of harmful microalgae of the genus Karenia. A spectral shape algorithm was used to detect algae. The algorithm calibration of in situ species composition data made it possible to identify areas where harmful algae dominated in biomass. Satellite images of chlorophyll-a concentra-tion, turbidity, specific fluorescence, and spectral shape parameter were computed. The images were used to recognize the stages of algal bloom: intensive growth, blooming, and change in the dominant algal species. Cases of an increase in the concentration of harmful substances in the coastal zone due to wind impact were analyzed. The following explanation of events has been offered. After the stage of intensive growth of microalgae, nutrient deficiency stimulated the production of metabolites that have a harmful effect on the environment. The change of the dominant alga species in the second half of September and the past storm contributed to a sharp increase in the concentration of metabolites and dead organic matter in the coastal zone, which caused an ecological disaster. The subsequent mass bloom of alga species of the same genus, and the regular wind impact leading to the concentration of harmful substances in the coastal zone, contributed to the development of this catastrophic phenomena.

Efficient natural convection-cooled heat sinks are vital to the future of electronics cooling due to their low energy demand in the absence of an external pumping agency in comparison to other cooling methods. The present study is aimed to identify the most effective fin design for enhancing heat transfer in natural convection applications. Initially, a baseline case with rectangular fins was considered in the present study and it was optimized with respect to fin spacing. This optimized baseline case is then validated against the semi-empirical correlation proposed by Elen-baas (1942) [2]. Upon good agreement, the validated model is used for comparative analysis of different heat sink configurations with rectangular, trapezoidal, curved, and angled fins. The optimised fin spacing obtained for the baseline case is also used for the other heat sink configura-tions and then the fin designs are further optimized for better performance. However, for the an-gled fin case, the optimized configuration proposed by Zhang et al. (2020) [3] is adopted in the present study. This study is carried out with Ansys Fluent for a Rayleigh number of 2.4 × 10^6. The proposed novel curved fin design with a shroud defined as Case C4 showed a 4.1% decrease in the system’s thermal resistance with an increase in the heat transfer coefficient of 4.4% when compared to the optimized baseline fin case. The obtained results are further non-dimensionalized with proposed scaling in terms of the baseline case for the two novel heat sink cases (trapezoidal, curved).