Rapid draw-down in an earthfill dam has serious implications for dam safety regarding slope stability. The evaluation of reservoir draw-down impact on slope stability was carried out considering the case study of 8 hours of rapid draw-down of the Middle Marsyangdi Hydroelectric Power Project (MMHPP) rock-fill dam using the Limit Equilibrium Method (LEM) and stress-based Finite Element Method (FEM). The time-dependent factor of safety (FOS) was evaluated and found that the 8 hours of rapid draw-down undertaken in October 2012 for reservoir flushing was unsafe with a draw-down rate of 1.91m/h. The resulting FOS of 1.28 and 1.27 using LEM and FEM was classified as unsafe as per the US Army Corps of Engineers’ guideline, the minimum required factors of safety should be greater than 1.3. The minimum safe allowable draw-down rate of 0.76m/h for 20 hours was identified. Applying three layers of horizontal filter materials and increasing the upstream dam’s permeability provided adequate FOS results for all cases by increasing seepage discharge to reduce the destabilizing excess pore water pressure. Several gradual draw-down rates were also tested and found that FOS increases with decreased draw-down rates, as it reduces the excess pore water pressure controlled with stabilizing existing water load.

In this study, we deal with a nonlinear system of neutral Volterra integro-differential equations (NVIDEs) with infinite delay. We study stability, uniform stability and instability of zero solution of the system of NVIDEs with infinite delay. We obtain three new results with regard to these concepts via two new Lyapunov– Krasovskii functionals (LKFs), respectively. As the main contributions of this work, we improve and generalize some earlier results in the relevant database from the linear case to more general nonlinear cases.

The global rising demand for exploiting limited shared groundwater resources, coupled with significant water deficit, especially in arid and semi-arid regions, has led to escalating conflicts among stakeholders. As such, using Bankruptcy Theory methods can be an appropriate response to the reallocation of resources. This study introduces a novel approach to weighted Bankruptcy, where the relative importance of stakeholders is determined by their contributions to sustainable development, and the impact of their claims on the shared groundwater resources is considered. The framework is implemented in a two-level bankruptcy process including the plains and their beneficiaries (agriculture, drinking and industry). The proposed two-level weighted bankruptcy process applies to the Neyshabour-Ataiyeh-Sabzevar plains in Iran. The process is implemented for two scenarios including the Baseline scenario related to the present status of demands and the Future scenario associated with the estimated demands for the year 2041. To compare the weighted proposed method with the other weighted methods such as Proportional (WPRO), Constrained Equal Awards (WCEA), Pinile (WPIN), Talmud (WTAL), Constrained Equal Losses (WCEL), Modified Constrained Equal Losses (MWCEL), two categories including the deficit-based and resource-based approaches are considered. According to the stability analysis using the Bankruptcy Allocation Stability Index (BASI) method, among the deficit-based methods, the novel approach is chosen as the preferred method for the beneficiaries’ reallocation like the Sabzevar’s beneficiaries. Accordingly, it allocates 86.95%, 10.86% and 2.17% of the shared resource to the agricultural, drinking, and industrial demands, respectively. Among the resource-based methods, the WPIN method is selected for reallocation between the stakeholders and their beneficiaries in each level and scenario of reallocation. The novel approach offers a promising solution to the water resource reallocation problem, ensuring a more equitable and sustainable management of shared groundwater resources.

In recent years, the use of solid waste fillers to partially replace natural fillers in asphalt mixtures to produce high-performance asphalt mixtures has received widespread attention. However, differences in the material properties of solid waste fillers remain a problem for this recycling method. To address this issue, limestone powder in asphalt mixtures was replaced by three solid waste fillers (steel slag powder, tailings powder and calcium carbide slag powder) in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, AC and SMA asphalt mixtures were designed and produced and characterized for wet stability. The results showed that asphalt mixtures with solid waste fillers were superior to LP asphalt mixtures in terms of resistance to water damage, and steel slag powder showed the best improvement in moisture stability of asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. In addition, the moisture stability of asphalt mixture with limestone filler was significantly improved with the addition of anti-stripping agents. In contrast, the moisture stability of asphalt mixtures with solid waste filler was slightly improved. Solid waste fillers could be used in asphalt mixtures and have a similar function as the anti-stripping agent. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added, recycling option.

In this study, we introduce the dynamics of a Hepatitis B virus (HBV) model with the class of asymptomatic carriers and conduct a comprehensive analysis to explore its theoretical aspects and examine the crossover effect within the HBV model. To investigate the crossover behavior of the operators, we divide the study interval into two subintervals. In the first interval, the classical derivative is employed to study the qualitative properties of the proposed system, while in the second interval, we utilize the ABC fractional differential operator. Consequently, the study is initiated using the piecewise Atangana-Baleanu derivative framework for the systems. The HBV model is then analyzed to determine the existence, Hyers-Ulam (HU) stability, and disease-free equilibrium point of the model. Moreover, we showcase the application of an Adams-type predictor-corrector (PC) technique for Atangana-Baleanu derivatives and an extended Adams-Bashforth-Moulton (ABM) method for Caputo derivatives through numerical results. Subsequently, we employ computational methods to numerically solve the models and visually present the obtained outcomes using different fractional-order values. This network is designed to provide more precise information for disease modeling, considering that communities often interact with one another, and the rate of disease spread is influenced by this factor.

Keywords: Аrtificial neural network, electric drive system, database, stability, training algorithm, technological mechanisms.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Derivatives products have become essential in portfolio diversification, price discovery and risk hedging. Derivatives are complex instruments; their role is twofold, risk management and speculation, and their actual Impact on the underlying assets’ behaviours are not well understood. Little is documented empirically on how these instruments’ two-edged roles influence firms’ financing decisions, firm risk exposures, and stability. Given the growing interest in using derivatives in risk management and portfolio engineering, this study examines the practical impact of derivatives usage on the underlying firm’s financing policy and stability. The paper uses data from South African listed non-financial firms for the period 2000 to 2019. The study employs a dynamic panel model estimated with System Generalised Methods of Moments (GMM). The initial analysis shows that derivatives use reduces the cost of capital and increases firm stability. However, further in-depth analysis provides evidence that extensive use of derivatives increases firms’ capital costs and negatively impacts financial stability. These findings imply that the risk embedded in derivatives’ speculation dominates their risk management function. The results are subjected to numerous controls for robustness, including financial leverage, firm size, cashflows and asset tangibility.

Intercropping of maize (Zea mays L.) and peanuts (Arachis hypogaea L.) (M||P) significantly enhances crop yield. In a long-term M||P field experiment with two P fertilizer levels, we examined how long-term M||P affects topsoil aggregate fractions and stability, organic carbon (SOC), available phosphorus (AP), and total phosphorus (TP) in each aggregate fraction, along with crop yields. Compared to their respective monocultures, long-term M||P substantially increased the proportion of topsoil mechanical macroaggregates (7.6–16.3%) and water-stable macroaggregates (>1 mm) (13.8–36.1%), while reducing the unstable aggregate index (ELT) and the percentage of aggregation destruction (PAD). M||P significantly boosted the concentration (12.9–39.9%) and contribution rate (4.1–47.9%) of SOC in macroaggregates compared to single crops. Moreover, the concentration of TP in macroaggregates (>1 mm) and AP in each aggregate fraction of M||P exceeded that of the respective single crops (P<0.05). Furthermore, M||P significantly increased the Ca2-P, Ca8-P, Al-P, and Fe-P concentrations of intercropped maize (IM) and the Ca8-P, O-P, and Ca10-P concentrations of intercropped peanuts (IP). The land equivalent ratio (LER) of M||P was higher than one, and M||P stubble improved the yield of subsequent winter wheat (Triticum aestivum L.) compared with sole-crop maize stubble. P application augmented the concentration of SOC, TP, and AP in macroaggregates, resulting in improved crop yields. In conclusion, our findings suggest that long-term M||P combined with P application, sustains farmland productivity in the North China Plain by increasing SOC and macroaggregate fractions, improving aggregate stability, and enhancing soil P availability.

The objective of this work was to improve the thermal stability, flame resistance and surface properties of black poplar (Populus nigra L.) wood via different impregnation methods. The impregnation method was employed through two distinct modalities: vacuum impregnation and immersion impregnation. Here, poplar wood was impregnated with calcium oxide solutions (1%, 3% and 5%). Fourier transform infrared spectroscopic analysis revealed a shift in the typical peaks of cellulose, hemicellulose, and lignin depending on the impregnation method and solution ratio. Thermogravimetric analysis and the limiting oxygen index indicated that the samples impregnated with lime solutions exhibited higher thermal stability than the unimpregnated wood. In both impregnation methods caused a decrease water absorption and thickness swelling of the sample groups. Using a scanning electron microscope, the effect of the impregnation process on the structure of the wood was examined. In terms of surface properties, it was determined that the surface roughness value increased. On the contrary, it was observed that the contact angle value also increased. A significant difference emerged between the applied methods. In conclusion, the applied lime minerals are suitable substances to increase flame resistance and thermal stability of black poplar wood.

The chemically synthesized polymer polyacrylamide (HPAM) in conventional reservoirs has achieved excellent oil displacement, but its oil displacement is poor in extreme reservoir environments. To develop biopolymer oil flooding agent under extreme reservoir conditions, the viscosity increasing and rheological properties of three biopolymers, diutan gum, xanthan gum, and scleroglucan, were studied under extreme reservoir conditions (high salt, high temperature, strong acid, and alkali), and the effects of temperature, mineralization, pH, and other factors on their viscosities and long-term stability properties were analyzed and compared. The results showed that under the temperature of 90℃ and below, the three kinds of biopolymers had the best viscosity-increasing ability. The viscosity of the three kinds of biopolymers was 80.94, 11.57, and 59.83mPa·s, respectively, when the concentration was 1500mg/L and the salinity was 220g/L. At the shear rate of 250s-1,100℃~140℃, scleroglucan has the best viscosification. At 140℃, the solution viscosity is 19.74mPa·s, and the retention rate can reach 118.27%. The results of the long-term stability study showed that the solution viscosity of scleroglucan with mineralization level of 220 mg/L was 89.54% viscosity retention in 40 days, and the diutan gum could be stabilized for 10 days, and the viscosity was maintained at 90 mPa·s. All three biopolymers are highly acid and alkali-resistant, with viscosity variations of less than 15% in the pH3~10 range. Rheological tests have shown that both of them have better viscoelastic properties than xanthan gum due to the peculiar double-helix structure of xanthan gum and the rigid triple-helix structure of scleroglucan. Therefore, the two biopolymers, diutan gum, and scleroglucan have the potential for extreme reservoir oil displacement applications, and it is recommended to use diutan gum for oil displacement in reservoirs up to 90℃ and scleroglucan for oil displacement in reservoirs between 100℃ and 140℃.

The paper investigates into the intricacies of semiconductor manufacturing, a highly complex process entailing a wide array of subprocesses and diverse equipment. Semiconductors are miniaturized integrated circuits comprising numerous components. The semiconductor manufacturing process begins with the thin disc-shaped silicon wafers. On each wafer, up to thousands of identical chips can be prepared depending upon the diameter of the wafer to build up the circuits layer by layer in a wafer fab. The size of the semiconductors requires a high number of units to be produced, thus necessitating a large amount of data to control for improving the semiconductor manufacturing process. Therefore, the collection and analysis of the equipment data, process data, and machine history data throughout the manufacturing process are required to diagnose faults, monitor the process, and manage the manufacturing process effectively. This research is focused on improving the semiconductor manufacturing process through a rigorous analysis of collected manufacturing process data, employing statistical process control (SPC), data mining techniques, and data-driven decision models. The project's primary objective is to increase the manufacturing process stability and productivity by utilizing the latest data-driven technologies in the scientific community. A structured review was undertaken, exploring contemporary data-driven methodologies in semiconductor manufacturing process improvement, specifically pertaining to process capability, product yield rate, and process stability. This review accentuates a comprehensive evaluation of data-driven methodologies applicable to conventional semiconductor manufacturing facilities, aiming to drive substantial process improvements. It features a detailed demonstration facilitating the selection of optimal semiconductor manufacturing processes to enhance overall operational performance. This study of process improvement in the semiconductor manufacturing steps through the application of data-driven methodologies will be effective in delivering advanced, real-time, and proactive control decisions throughout the manufacturing facilities. This endeavor is expected to promptly provide critical insights for enterprise manufacturing decision-makers to reduce manufacturing cycle time, improve the product yield rate, and increase the overall efficiency of the manufacturing process.

Amaranth has the potential to support Malawi's food and nutrition security, income generation and livelihoods, and climate change resilience efforts. Due to the high genetic variability of Ama-ranth, there is a need to develop stable and high-yielding genotypes for sustainable production. To determine the degree of genetic stability in different environments, five Amaranth accessions were subjected to stability analysis. The experiment was carried out at three sites (Bunda, Bembeke, and Chipoka) for two seasons in 2020-2021 in the central region of Malawi. It was laid out in Ran-domized Complete Block Design (RCBD) with four replicates. Eberhart and Russell linear regres-sion model was used for stability analysis and Pearson correlation was used to test the relationship between variables. Environmental variance + (genotype x environment) was significant for four of the parameters studied, namely grain yield, plant height, leaf length, and leaf width, indicating the presence of a remarkable interaction between genotypes and environment. The results of a pooled analysis of variance showed significant differences at a 5% significance level among the Amaranth accessions, indicating inherent genetic variability. Using the linear regression model of Eberhart and Russell, accessions PE-LO-BH -01 and LL-BH -04 were identified as the highest yielding stable genotypes for leaf and grain yield, respectively. In addition, Bembeke site was the most favourable environment for all the accessions. Thus, to enhance the production of amaranth in Malawi, LL-BH-04 and PE-LO-BH-01 were put forward for release as varieties for grain and leaf respectively. These results will also guide and support for future breeding programs.

Typhoid fever is an infectious disease that affects humanity worldwide particularly in the lower socio-economic communities where many individuals are exposed to a dirty environment and unclean food. A mathematical model is formulated to analyze the impact of control measures such as vaccination of susceptible humans, treatment of infected humans and sanitation in the different socio-economic communities. The model assumed that the population comprises of two socio-economic classes. The essential dynamical system analysis of our model was appropriately carried out. The impact of the control measures was analyzed, and the optimal control theory was applied on the control model to explore the impact of the different control measures. Numerical simulation of the models and the optimal controls were carried out and results obtained indicates that the overall combination of the control measures eradicates Typhoid fever in the population but the controls are more optimal in the higher socio-economic communities.

The current deformation and stable state of slopes with historical shatter signs is a concern for engineering construction. Suspected landslide scarps were discovered at the rear edge of the slope of the Genie in the Sichuan-Tibet transportation corridor during a field investigation. In order to qualitatively determine the current status of the surface deformation of this slope, this paper uses high-resolution optical remote sensing, airborne LiDAR and InSAR technologies for comprehensive analysis. The interpretation of high-resolution optical and airborne LiDAR data revealed that the rear edge of the slope exhibits three levels of scarps. However, no deformation was detected with the D-InSAR analysis of ALOS-1 radar images from 2007 to 2008 or with the Stacking-InSAR and SBAS-InSAR processing of Sentinel-1A radar images from 2017 to 2020. A geological model of the slope was established in combination with field investigation stipulating that the slope is composed of steep anti-dip layered dolomite limestone and that the scarps at the rear edge of the slope were caused by historical shallow toppling. Further research is recommended to determine the extent of toppling deformation and evaluate the slope stability under the disturbance of tunnel excavation.

Studies on the long-term stability of meat analogs stored under frozen conditions are lacking. Here, we aimed to assess the storage stability of vegetable oil-supplemented meat analogs and analyze the effects of temperature and storage period on their physiochemical characteristics. The meat analogs were prepared by adding 30 g castor oil, orange oil, palm oil, shortening, or margarine vegetable oil based on 100 g of textured vegetable protein. They were then stored at −18 or −60 °C for 6 months and analyzed at one-month intervals. The meat analog supplemented with orange oil had the highest water content, liquid-holding capacity, hardness, and antioxidant activity. During frozen storage, temperature barely affected the meat quality. The storage stability of all meat analog samples was maintained for 6 months, although the quality was slightly reduced with an increase in storage duration. Coliform group bacteria were not detected regardless of the storage condition. Orange oil improved the juiciness of meat analogs, and the quality of samples was maintained for at least 6 months under frozen storage. The findings of this study are relevant to the development and promotion of vegetable meat as an alternative to animal meat.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. A doping-induced and concentration-dependent phase transition in ZrO₂ under the influence of Y₂O₃ was discovered, due to which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The results show that ab initio approaches are able to describe the mechanism of doping-induced phase transitions in (ZrO₂+Y₂O₃)-like systems, based on which it can be assumed that DFT calculations can also flawlessly evaluate other physical and chemical properties of YSZ, which have not yet been studied quantum chemical research. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Aim: Complementary effects of dabigatran etexilate (DE), exercise training (ET) and combination (DE+ET) on the development and composition of the atherosclerotic lesions in diabetic apoE knockout (apoE-/-) mice. Methods: In 48 male apoE-/- diabetic mice, streptozotocin (STZ) was induced for 5 consecutive days. Mice received figh-fat diet (HFD) for 8 weeks and were randomized into 4 groups (1.Control/CG, 2.DEG: HFD with DE, 3.ETG: ET on treadmill, 4.DE+ETG: Combination DE and ET treatment). At the end of 8th week, all mice were euthanatized and morphometry of the aortic lesions at the level of aortic valve was obtained. Collagen, elastin, TNF-a, MCP-1, matrix-metalloproteinases (MMP-2,-3,-9), and TIMP-1 concentration within plaques at aortic valve were determined. Results: All active groups had significantly smaller aorta stenosis (DEG:7.9±2.2%, ETG:17.3±5.3%, DE+ETG:7.1±2.7%) compared to CG (23.3±5.5% p&lt;0.05), reduced the relative intra-plaque concentrations of macrophages, MCP-1, MMP-3 and MMP-9, and considerably increased collagen, elastin and TIMP-1 (p&lt;0.05). Group 4 showed the most pronounced results (p&lt;0.05). Both DEG and DE+ETG significantly reduced MMP-2 and TNF-a concentrations compared to ETG and CG (p&lt;0.010). Conclusion: DE and ET treatment in diabetic apoE-/- mice showed complementary amelioration of atherosclerotic lesions development and stability, mediated by the anti-inflammatory modulation of both DE and ET.

Deep Neutral Networks (DNNs) were initially proposed towards the midst of the 20th century, motivated by the neural structure and mechanism of the human brain. Thanks to major ad-vancements in computational resources, during the past decade DNN-based systems have demonstrated unprecedented performance in terms of accuracy and speed. However, recent work has shown that such models may not be sufficiently robust during the inference process. Furthermore, due to the data-driven learning nature of DNNs, designing interpretable and gen-eralizable networks is a major challenge, especially in critical applications, such as medical Computer Aided Diagnostics (CAD) and other medical imaging tasks, including classification, regression and reconstruction. Within this context, a line of physics-driven approaches for deep learning has recently emerged, aimed at improving the stability and generalization capacity of DNNs for medical imaging applications. In this paper, we review recent work focused on phys-ics-driven or prior-information learning for a variety of imaging modalities and medical applica-tions. We discuss how the inclusion of domain-related knowledge into the learning process and networks’ design supports their stability and generalization capability. In addition, we highlight current and future challenges within this scope.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, low friction coefficient, excellent optical properties, and extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a Ta/ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system, with tantalum (Ta) serving solely as a transition layer. Subsequently, Zr and Nb ions were implanted into the film at varying doses but with consistent energy levels. The analysis focused on the film's microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrated a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of - 0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

The time-dependent behavior and long-term stability of deep-buried tunnels in soft rocks have received lots of considerations in tunnel engineering and allied sciences. To better explore and deepen the engineering application of rock creep, extensive research studies are still needed, although fruitful outcomes have already obtained in many related investigations. In this article, the Weilai Tunnel in China’s Guangxi province is studied taking its host rocks as the main research object. In fact, aiming at forecasting the time-varying deformation of this tunnel, a novel elasto-visco-plastic creep constitutive model with two variants is proposed, by exploiting the typical complex load-unload process of rock excavation. The model is well validated and good agreements are found with the relevant experimental data. Moreover, the time-dependent de-formation rules are properly established for the surrounding rocks, by designing two new closed-form solutions based on the proposed creep model and the Hoek-Brown criterion. The convergence deformations calculated from the closed-form solutions conform well to the on-site monitoring data. In only 27 days after excavation, the creep deformation of the Weilai tunnel overtakes 400 mm, which is enormous. To guarantee the long-term stability of this tunnel, a ro-bust support scheme and its long-term monitoring with appropriate remote sensors are strongly suggested.

This study investigates the stochastic dynamics of hepatitis B virus (HBV) infection using a newly proposed stochastic model. Contrary to deterministic models that fail to encapsulate the inherent randomness and fluctuations in biological processes, our stochastic model provides a more realistic representation of HBV infection dynamics. It incorporates random variability, thereby acknowledging the changes in viral and cellular populations and uncertainties in parameters such as infection rates and immune responses. We examine the solution's existence, uniqueness, and positivity for the proposed model, followed by a comprehensive stability analysis. We provide the necessary and sufficient conditions for local and global stability, offering deep insight into the infection dynamics. Furthermore, we utilize numerical simulations to corroborate our theoretical results. This research provides a robust tool for understanding the complex behavior of HBV dynamics, contributing significantly to the ongoing quest for more effective HBV control and prevention strategies.

Curcumin, a nontoxic and cheap natural medicine, has high therapeutic efficacy for many diseases including diabetes and cancers. Unfortunately, its exceedingly low water-solubility and rapid degradation in the body severely limit its bioavailability. In this work, we prepare a series of biocompatible poly(vinyl anisole)@nonlinear poly(ethylene glycol) (PVAS@PEG) core-shell nanogels with different PEG gel shell thickness to provide high water solubility, good stability, and controllable sustained release of curcumin. The PVAS nanogel core is designed to attract and store curcumin molecules for high drug loading capacity and the hydrophilic nonlinear PEG gel shell is designed to offer water dispersibility and thermo-responsive drug release. The obtained nanogels are monodispersed in spherical shape with clear core-shell morphology. The size and shell thickness of the nanogels can be easily controlled by changing the core-shell precursor feeding ratios. The optimized PVAS@PEG nanogels display a high curcumin loading capacity of 38.0 wt%. The nanogels can stabilize the curcumin from degradation at pH =7.4 and release the curcumin in response to heat in the physiologically important temperature range. The nanogels can enter cells effectively and exhibit negligible cytotoxicity to both the B16F10 and HL-7702 cells at a concentration up to 2.3 mg/mL. Such designed PVAS@PEG nanogels have a great potential to be used for delicate drug delivery.

This work studied sorption regularities and assessed thermal stability and resistance to microbial degradation of humic acid as a result of 3 sorption cycles on bentonite clay, kaolinite, and muscovite using TGA/DSC, XRD, hydrophobic chromatography, light and electron microscopy, etc. The experiment revealed that kaolinite sorbed more humic acids (HAs) in terms of unit surface area (1.03 × 10-3 C, g/m2) compared to bentonite (0.35 × 10-3 C, g/m 10-3 g/m2). Sorption at pH 4.5 was accompanied by HA fractionation in amphiphilicity and chemical composition. HA was sorbed mainly due to hydrophobic components on the surface of all sorbents. HA was not intercalated into the interlayer spaces of montmorillonite during sorption. Sorption due to hydrophilic interactions was mostly performed on muscovite and bentonite than on kaolinite. Sorption was followed by a change in the chemical composition of HA and decreased C/N compared to free HA, indicating selective sorption of nitrogen-containing compounds which is most characteristic of muscovite. Only a relatively thermolabile HA fraction was adsorbed on all minerals while its thermal stability increased compared to that before the experiment. Thermal stability and ratio of the Exo2/Exo1 peak areas on the DSC curves of sorbed HA increased with each subsequent sorption cycle. Thermal stability and resistance to microbial oxidation of sorbed HA showed the following relationship: the higher the thermal stability, the less available is sorbed HA for utilization by microorganisms.

The use of biolubricants as an alternative for petroleum-based products has played an important role in the last decade. Thus, due to the encouragement of global policies, which mainly support green chemistry and circular economy, there has been an increasing interest in bio-based products, including biolubricants, from scientific and industrial points of view. Due to the different applications of biolubricants for a wide range of practical uses, the raw materials, production, and characteristics might vary, making this field a continuously changing subject of study by researchers. The aim of this research work was to focus on biolubricant production from vegetable oil crops in a bio-refinery perspective, paying attention to the main raw materials used, the corresponding production methods (with special focus on double transesterification), the role of catalysts and techno-economic studies. Thus, the main factors affecting quality parameters such as viscosity or oxidative stability have been covered, including catalyst addition, reaction temperature or the use of raw materials, reagents or additives were also analyzed. The latest research trends were included, updating previous studies about this matter, considering current conclusions and future research.

The present study aimed to evaluate the effect of the citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid over the physical properties of wood. After choosing the best treatments (170°C and 5% and 10% of citric acid) it was evaluated the effect of these on the chemical properties (SEM, FTIR and pH), on the density profile using an X-ray microtomography, and on the resistance to ageing through abrasion test. The result of the chemical analysis allowed to observe an increase of the presence of ester functional groups, as well as a better coverage and higher acidity of the surface. The density profile technique allowed to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasion because of the application of the citric acid.

This work investigates the sliding mode control (SMC) problem for a class of uncertain switched systems subject to asynchronous switching and an assigned finite time constraint. Two important issues are how to ensure the reachability of state trajectories within the assigned time and the input-to-output finite-time stability (IO-FTS) of the closed-loop switched systems during the whole phase under asynchronous switching. To achieve these objectives, an asynchronous sliding mode controller with adjustable parameters is constructed to drive the state trajectories onto the sliding surface during the assigned finite-time interval. By means of the partitioning strategy, sufficient conditions for the IO-FTS of the closed-loop switched are derived during the whole phase [0,T] using the multiple Lyapunov function (MLF) approach. Additionally, the asynchronous characteristics are detailedly investigated while analyzing the reachability of a specified sliding surface. Finally, an illustrative example is given to illustrate the effectiveness of the proposed method.

This study proposes a nonlinear mathematical model of virus transmission based on the SEIR model. In this study, the interaction between viruses and immune cells is investigated using phase-space analysis of a mathematical model. Specifically, it is focused on the dynamics and stability behavior of the mathematical model of a virus spread in a population and its interaction with human immune systems cells. The endemic equilibrium points are found and local stability analysis of all equilibria points of the related model is obtained. Further, the global stability analysis either, at disease-free equilibria, or in endemic equilibria is discussed by constructing the Lyapunov function which shows the validity of the concern model exists. Finally, a simulated solution is achieved and the relationship between viruses and immune cells is highlighted.

The center of mass dynamics of human seated posture in a work environment under hypogravity (0<g<1) have rarely been investigated and it remains to be accomplished. The present study determined the difference in the body system of 32 participants working under simulated 1/6g (Moon) and 1g (Earth) for comparison reason using static and dynamic action measurements. This was based on analyzing the participant's center of mass before, during, and after the task when they started to get fatigued. According to this analysis, there is a positive relation (p<0.01) with a positive coefficient of correlation between CoM body shift down along the Y axis and gravity level for males and females. At the same time, the same positive relationship (p<0.01) between the tilt of the body back along the Z axis and the level of gravity was found only in females. This offers fresh perspectives for comprehending hypogravity. It can also improve workplace ergonomics, body stability, equipment design, and biomechanics.

In this study, considering the peroxidase-like activity of the SiO₂@AuNPs nanocomposite, their biochemical properties including, pH stability, cycling stability, shelf stability, and kinetic parameters were investigated. The results revealed that the as-mentioned SiO₂@AuNPs nanocomposite reveal its maximal activity at pH=4.0 along with saving 83.3% of its maximal activity at pH=5.0. Besides, the reusability and shelf-storage studies exhibited that the SiO₂@AuNPs nanocomposite retained 90% and 100% of its initial activity after 5 operational cycles and 30 days of storage, in order. The kinetic parameters of the as-prepared nanozymes were calculated using Menten kinetic model, revealing a V_max of 1.35 µM min^-1 and a K_m as low as 0.06 mM for the SiO₂@AuNPs nanocomposite. Based on the results of this work, the as-prepared SiO₂@AuNPs nanocomposite with intrinsic peroxidase-like activity shows high substrate affinity and catalytic efficiency along with excellent cycling- and shelf-stability, making them suitable for application in peroxidase-mediated reactions instead of the native enzyme.

Among the main elements that contribute to climate change are degradation processes and the ecological level of the landscape. These two topics have been discussed and researched for many years and many studies have been conducted. The idea of the article is to determine the correlation between the ecological stability of the territory and the intensity of degradation processes and find out how the ecological stability affects the intensity of soil erosion and vice versa. The ecological stability was calculated based on various methods during the years analyzed, i.e., 1990, 2006, 2012, and 2018. The soil water erosion was performed for the same period in order to identify the relationship between the ecological stability and intensity of soil erosion. The investigated area is located in the Slovak Republic while each year reflects different management of the territory reflecting the current situation in the catchment according to the year evaluated. The intensity of the erosion process was conducted using a phycially-based EROSION-3D model and based on the precipitation derived using Community Land Model (the CLM model). In addition to identifying the relationship between the level of ecological stability and the intensity of erosion, this study also describes the development the ecological stability during the evaluated period together with changes in soil erosion processes.

The Chen circuit system, a three-dimensional autonomous system with intriguing dynamics, has gained considerable attention due to its potential applications in diverse scientific fields. In this article, a Chen circuit-like system is defined and a comprehensive dynamics has been studied. The system exhibits chaotic dynamics, limit cycles, and bifurcations, making it a captivating subject of study. By employing numerical simulations and analytical techniques, we explore the system's stability and identify critical parameter values leading to qualitative changes. Notably, we delve Hopf bifurcations, which give rise to stability changes and the emergence of limit cycles. Furthermore, we analyze the fractal dimension of the system's attractor, providing insights into its complexity and self-similarity. Through a systematic examination of the Chen circuit-like system, we deepen our understanding of its intricate dynamics and offer valuable insights into the underlying mechanisms. The findings contribute to the field of dynamical systems and hold potential implications in areas such as chaos-based secure communications, signal processing, and nonlinear control. This work serves as a valuable reference for researchers and practitioners interested in the dynamics and bifurcation analysis of nonlinear systems.

Since the come up in the 70´s, various decentralized control methodologies have been developed to deal with the challenge of controlling complex and/or spatially distributed systems with multiple inputs and multiple outputs (MIMO), e.g., chemical plants, power systems, water systems, etc. In general, the use of distributed information and control structures requires to synthesize control laws in a constrained (decentralized) information structure. The article presents another version of the unified frequency domain robust decentralized controller design method [1]. The proposed design procedure is appropriate for uncertain dynamic MIMO systems given as a set of transfer function matrices. Its main framework is provided by the Equivalent Subsystems Method [1, 24] guaranteeing fulfillment of the necessary and sufficient stability condition of the overall closed-loop system if individual closed-loop equivalent subsystems are stable. Generating sets of equivalent subsystems for all transfer function matrices describing the uncertain MIMO plant allows to use the QFT method [19] to independently design local robust SISO controllers that constitute the resulting decentralized controller implemented on true subsystems. The developed design procedure is verified and illustrated on a case study on robust decentralized level controller design for a quadruple tank process [2, 24].

In this study, we construct a new Atangana-Baleanu fractional model for whooping cough disease to predict future dynamics of the disease, as well as to suggest strategies to eliminate the disease in an optimal way. We prove that the proposed model has a unique solution which is positive and bounded. To measure contagiousness of the disease, we determine the reproduction number R0 and use it to examine the local and global stability at equilibrium points that have symmetry. Through sensitivity analysis, we determine parameters of the model that are most sensitive to R0. The ultimate aim of this research is to analyze different disease prevention approaches in order to find the most suitable one. For this, we include the vaccination and quarantine compartments in the proposed model and formulate an optimal control problem to assess the effect of vaccination and quarantine rates on disease control in three distinct scenarios. Firstly, we study the impact of vaccination strategy and conclude findings with presentation of graphical results. Secondly, we examine the impact of quarantine strategy on whooping cough infection with possible elimination from the society. Lastly, we implement vaccination and quarantine strategies together to visualize their combine effect on infection control. In addition to the study of an optimal control problem, we examine the effect of fractional order on disease dynamics as well as the impact of constant vaccination and quarantine rates on disease transmission and control. We determine that the optimal control strategy with the three controls is more effective in reducing the spread of whooping cough infection. Implementation of Toufik-Atangana type numercial scheme both for the state and adjoint equations is another contribution of this article.

Traditional vaccines are produced by using weakened or inactivated forms of disease-causing pathogens to produce the target antigen they are designed to protect against. Messenger RNA vaccines are a class of vaccines that employ a minute segment of genetic material, known as messenger RNA (mRNA), which contains directives for the cells in the body to generate a particular protein. This genetic material is synthesized in the laboratory and packaged into a lipid nanoparticle, which protects and helps it enter cells for further protein synthesis. During vaccination with mRNA vaccine, the lipid nanoparticles containing the mRNA are injected into the muscle of vaccinees. Once inside the cells, the mRNA instructs the cells to produce a protein which is then displayed on the surface of the cell, triggering an immune response. During this, the immune system recognizes the displayed protein as foreign and mounts a defense by producing antibodies and activating immune cells to target and eliminate the protein. Furthermore, these immune responses generate a memory cell, facilitating the immune system to promptly react in case of encountering the authentic pathogen as an infection in the future. The mRNA vaccines are flexible and the sequence can be easily synthesized in the lab based on the genetic information of the target pathogen. Additionally, mRNA vaccines can be developed for new strains or variants of the target disease easily. This was particularly evident during the COVID-19 pandemic, where mRNA vaccines like the Pfizer-BioNTech and Moderna vaccines were developed and authorized for emergency use within a year. But currently, available mRNA vaccines require extensive cold chain, antigen delivery, potential immune response variability optimization, and sophisticated manufacturing process. The efforts to explore next-generation mRNA vaccine development are aimed to further improve the effectiveness, stability, and delivery methods. One focus of research has been to enhance the stability of mRNA vaccines, particularly temperature sensitivity which makes storage and distribution easier, particularly in regions with limited access to cold chain infrastructure. Self-amplifying mRNA vaccines, on the other hand, are designed to generate multiple copies of the mRNA within cells which potentially leads to a higher production of the target protein, resulting in a stronger immune response. Additionally, studies are exploring new delivery systems to improve the target and efficiency of mRNA vaccines using specialized nanoparticles and liposomes to specifically deliver mRNA to certain cell types or immune cells. Another area of interest is the development of combination vaccines, where multiple mRNA sequences are included in a single vaccine protecting against multiple diseases targeting strains or variants of a particular pathogen simultaneously. While current mRNA vaccines are administered via intramuscular injection, studies are underway to deliver directly into the skin offering enhanced immune response and the ability to use smaller vaccine doses.

Transition metal alloys have emerged as promising electrocatalysts due to their ability to modulate key parameters such as d-band electron filling, Fermi level energy, and interatomic spacing, thereby influencing their affinity towards reaction intermediates. However, the structural stability of alloy electrocatalysts during alkaline hydrogen evolution reaction (HER) remains a subject of debate. In this study, we systematically investigate the structural evolution and catalytic activity of the c-Co/Co3Mo electrocatalyst under alkaline HER conditions. We reveal that the instability of the Co3Mo alloy and H0.9MoO3 during alkaline HER leads to the destruction of the crystal structure, resulting in the formation of hexagonal cobalt (h-Co) from hexagonal Co(OH)2 as an intermediate species. Furthermore, we explore the re-adsorption and surface coordination of the Mo element, which enhances the catalytic activity for alkaline HER. This work provides valuable insights into the dynamic behavior of alloy-based electrocatalysts, shedding light on their structural stability and catalytic activity during electrochemical reduction processes

Nickel-based Superalloy Inconel 718 is widely used in the aerospace industry for its excellent high-temperature strength and thermal stability. However, milling Inconel 718 presents challenges due to significantly increased cutting force and vibration, which is a typical difficult-to-machine material. This paper focuses on the milling process of Inconel 718, establishing a milling force model to analyze the force trends under various processing parameters. Finite element analysis is employed to study the stress and temperature fields during milling. Dynamic equations for milling Inconel 718 are developed, and stability lobe diagrams are generated based on modal experiments. Milling experiments on Inconel 718 validate the milling force model and finite element analysis results. The fmincon optimization algorithm is utilized to identify the optimal machining parameters for Inconel 718. Through this research, valuable insights into enhancing the efficiency and quality of Inconel 718 machining are provided. This study contributes to a deeper understanding of Inconel 718 milling behavior, offering crucial guidance for more efficient machining processes.

This study investigates the long-term impact of soil tillage systems and crop residue incorporation on agrophysical properties. A long-term field experiment has been conducted since 1999 at the Ex-perimental Station of Vytautas Magnus University Agriculture Academy. According to the latest edition of the International Soil Classification System, the soil in the experimental field was classified as Planosol, with a silty medium loam texture at a depth of 0–20 cm and a silty light loam at a depth of 20–40 cm. This investigation aimed to assess the long-term impact of reduced tillage systems, straw, and green manure combinations on soil physical properties, including soil shear strength, and soil aggregate stability. Studies were carried out on winter wheat crops in 2014, 2017, and 2023. The treatments were arranged using a split-plot design. In a two-factor field experiment, one part of the experimental field had straw removed, while the other part had the entire straw yield chopped and spread at harvest (Factor A). The subplot factor (Factor B) included three different tillage sys-tems: conventional deep ploughing, cover cropping for green manure with no-till, and no-tillage. Soil samples were analysed in the Laboratory of Agrobiology at Vytautas Magnus University Ag-riculture Academy. The findings indicate that long-term application of reduced tillage significantly increases soil shear strength. Shallower tillage depths lead to higher soil shear strength, while the effect of spreading plant residues is relatively lower. Long-term tillage of different intensities, spreading plant residues, and catch crop cultivation for green manure did not significantly affect soil structure. However, soil structural stability was found to be highly dependent on soil tillage. Cover cropping for green manure with no-till and no-tillage positively affected soil aggregate sta-bility in the upper (0–10 cm) and 10–25 cm layers.

Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

This research work aims to develop a mathematical modeling for production-inventory systems. Two mathematical models are present: An infinite dimensional, partial differential equation (PDE), production level modeling is present and a finite dimensional system for a coupled dynamic pricing, production rate and inventory level ordinary differential equations (ODE), integrating a proper Lyapunov stability analysis of the dynamical system and simulations.

A strong correlation between karyotype diversity and species richness in mammals was first reported over forty years ago: in mammalian phylogenetic clades, standard deviation of karyotype diversity (KD) closely corresponds to the standard deviation of species richness (SR). These initial studies, however, did not control for phylogenetic signal, raising the possibility that the correlation was due to phylogenetic relatedness among species in a clade. Accordingly, karyotype diversity trivially reflects species diversity simply as a passive consequence of adaptive radiations. A more recent study in mammals has controlled for phylogenetic signal and established the correlation as phylogenetically independent, suggesting that species diversity cannot, in itself, explain the observed corresponding karyotype diversity. The correlation is therefore remarkable because the mechanisms contributing to karyotype diversity are evolutionarily independent of the mechanisms contributing to species diversity. Recently, it was shown in salamanders that the two processes generating genetic diversity and species diversity are indeed independent and operate in parallel, suggesting a potential non-adaptive and non-causal relationship between the two fundamental variables involved in adaptive radiations. The following will examine the relationship between KD and SR in the context of Motoo Kimura’s theory of non-adaptive radiation.

To describe the hysteresis nonlinearities in smart actuators, numerous models have been presented in the literature, among which the Preisach operator would be the most effective one due to its capability in capturing multi-loop or sophisticated hysteresis curves. When such an operator is coupled with uncertain nonlinear dynamics, especially in noncanonical form, it is a challenging problem to develop techniques to cancel out the hysteresis effects, and at the same time achieve asymptotic tracking performance. To resolve this problem, in this paper, we investigate the problem of iterative inverse-based adaptive control for an uncertain noncanonical nonlinear systems with unknown input Preiasch hysteresis, and a new adaptive version of the closest match algorithm is proposed to compensate for the Preisach hysteresis. With our scheme, the stability and convergence of the closed-loop system can be established. The effectiveness of the proposed control scheme is illustrated by simulation and experiment results.

Japanese pepper (sansho, Zanthoxylum piperitum) contains several types of sanshools belonging to N-alkylamides. Because of long-chain unsaturated fatty acids present in their structure, sanshools are prone to oxidative deterioration, which poses problems in processing. Here, we evaluated the effects of antioxidants from the genus Zanthoxylum in preventing sanshool degradation using accelerated tests. An ethanolic extract of segment membranes of the sansho fruit pericarp was incubated at 70 °C for 7 days with different antioxidants to determine the residual amount of hydroxy-α-sanshool (HαS) in the extract. α-Tocopherol (α-Toc) showed excellent HαS-stabilizing activity at low concentrations. Among phenolic acids, we noted that the HαS-stabilizing activity increased with the number of hydroxy groups per molecule. For example, gallic acid and its derivatives exhibited excellent sanshool-stabilizing activity. Quercetin was found to be a superior HαS stabilizer compared with hesperetin and naringenin. However, the effective concentration was much higher for phenolic compounds than for α-Toc. These substances are believed to play a role in preventing the decomposition of sanshools in the pericarp of sansho. These sanshool stabilizers should be useful in the development of new beverages, foods, cosmetics, and pharmaceuticals that take advantage of the taste and flavor of sansho.

An experiment was conducted in 2016 & 2017 for development of novel rice hybrids for aerobic ecology with lesser yield penalties in comparison to irrigated ecosystem, further with added advantage of reduced methane emissions and water budget as witnessed in irrigated system. Based on the restorer / maintainer reaction and spikelet fertility (%), 10 restorer lines were selected to cross with 3 CMS lines in the line by tester fashion in Yasangi (summer) season 2016-17. Resulting 30 experimental hybrids besides 13 parental lines (10 Restorer lines and 3 B - lines of akin CMS lines) and checks (GK 5022, CR Dhan 201) assessed during Vankalam (rainy) season 2017 at three different places/locations viz., Rajendranagar, Warangal and Kampasagar. The outcome of experiment were two experimental hybrids viz., APMS-6A × HRSV – 7 and IR-79156A × ATR – 372, were categorized as stable hybrids with desirable sca effects, heterosis (ranging from 7% to 13%) over best check GK 5022 along with an in-essence performance for yield and other yield attributing characters.

Coronavirus disease 2019 (COVID-19) is a high contagious respiratory infectious disease that has afiected millions of people worldwide. Initially, basic public health measures were implemented to control specially the spread of such virus. However, vaccination has emerged as a highly efiective strategy in combating COVID-19 and reducing its transmission. Several efiective and safe vaccines have been approved to prevent the inadvertent spread of the disease. In this study, a modeling approach is used to analyze the impact of these vaccines on the dynamics of COVID-19. By applying a higher-order numerical method, the model is solved based on reported cases in Pakistan. A spectral method is employed for the numerical solution, and the model is simulated to assess the efiects of vaccination. The Next-generation method is used to calculate the threshold quantity, known as R0, which indicates the potential for disease transmission. The study also includes a detailed stability analysis, examining the invariance properties of the model solution and discussing equilibrium points and their stability in disease-free and endemic states. Furthermore, the study presents graphical representations of the influence of special parameters on the dynamics of the pandemic.

The present study sought to determine the effect of incorporating a Chitosan-TiO2 nano-composite on the color stability of pigmented Room Temperature Vulcanization (RTV) maxillofacial silicone subjected to a variety of accelerated aging conditions. The experimental setup consisted of one hundred groups of five disk-shaped specimens (22mm diameter, 2mm thick) each, created using RTV silicon elastomer type A-2186, with the total sample distributed into four groups based on the pigments combined with the silicon—specifically, brilliant red, blue, and yellow dry intrinsic pigments (at 0.2% concentration by weight) and a fourth group that remained non-pigmented. Each of these primary groups was further subdivided into five categories corresponding to the silicon variants treated with different nanoparticles—2% TiO2, 3% Chitosan, a hybrid nano-combination of 1% TiO2/Chitosan, 1% synthesized Chitosan-TiO2 Nanocomposite, and a control group devoid of nanoparticle additions. The synthesized Chitosan-TiO2 Nanocomposite was effectively prepared using the core-shell method. The color stability of each silicon category, irrespective of whether pigmented or non-pigmented was evaluated by calculating the color difference (ΔE) pre- and post-subjection to five distinct accelerated aging conditions: 30 hours in an antibacterial cleaning solution, six months in sebum, six months in sweat, UV-accelerated aging for 720 hours, and outdoor weathering for six months. Color measurements were taken using a Colorimeter within the CIELAB color system. Statistical analyses, including one-way ANOVA at a significance level of p < 0.05, were employed to discern significant differences among the various accelerated aging conditions across the five silicon categories. Further comparisons were made using Dennett's T3 multiple comparison test, Tukey HSD multiple comparisons, and a t-test, with SPSS for Windows version 27.0 as the software platform. Results indicated that all silicon types, whether pigmented or not, exhibited varying degrees of color change under different aging conditions. Red-colored samples, across all silicon categories, demonstrated significant color alterations after 720 hours of UV-accelerated aging, with the most pronounced change in the 3% Chitosan samples and the least in the 2% TiO2 samples. Six months of outdoor weathering led to a marked increase in ΔE values across all categories. The blue-pigmented silicon samples treated with 2% TiO2 showed the highest color modification, while the yellow-pigmented silicon and non-pigmented silicon also underwent significant color shifts, particularly in the control and Chitosan-TiO2 categories, respectively. The study underscores the pervasive influence of outdoor weathering on color stability across all silicon categories. It also demonstrates that while nanoparticle incorporation offers some resilience against accelerated aging, it fails to provide adequate protection against the specific effects of UV radiation encountered during outdoor weathering.

Silica aerogels and their derivatives have outstanding thermal properties with exceptional values in the thermal insulation industry. However, the brittle nature restricts its large-scale commercialization. Thus, enhancing their mechanical strength without affecting their thermal insulating properties is essential. Therefore, for the first time, highly thermally stable Poly(acrylamide-Co-acrylic acid) partial sodium salt is used as a reinforcing polymer to synthesize hybrid P(AAm-CO-AAc)-silica aerogels via epoxy ring-opening polymerization in the present study. Functional groups in P(AAm-CO-AAc) partial sodium salts, such as CONH2 and COOH, acted as nucleophiles for the epoxy ring-opening reaction with (3-glycidyloxypropyl)trimethoxysilane, which resulted in a seven-fold enhancement in mechanical strength compared to that of a pristine silica aerogel while maintaining the thermal conductivity at less than 30.6 mW/mK and porosity of more than 93.68%. Moreover, the hybrid P(AAm-CO-AAc)-silica aerogel demonstrated improved thermal stability up to 343 ⁰C owing to the synergetic effect between P(AAm-CO-AAc) and the silica aerogel, corresponding to thermal stability and strong covalent bonding among them. These excellent results illustrate that this new synthetic approach for producing hybrid P(AAm-CO-AAc)-silica aerogels is useful for enhancing the mechanical strength of a pristine silica aerogel without impairing its thermal insulating property and shows potential as an industrial heat insulation material.

The coffee plant is highly susceptible to drought, and different genotypes exhibit varying degrees of tolerance to low soil moisture. The current study aims to investigate the connection between drought tolerance and sensitivity in terms of seed traits, germination, and post-germination events, and their influence on the growth and physiology of young coffee plants. Two consecutive experiments were conducted to examine the impact of these factors. In the first experiment, germination performance was examined for three groups of coffee genotypes: relatively tolerant (Ca74140, Ca74112, and Ca74110), moderately sensitive (Ca74158, Ca74165, and CaJ-21), and sensitive (Ca754, CaJ-19, and CaGeisha). The subsequent experiment focused on the growth and physiological responses of two relatively tolerant (Ca74110 and Ca74112) and two sensitive (CaJ-19 and Ca754) genotypes under drought stress condition. The relatively tolerant genotypes showed quicker and more complete germination compared to other groups. This was associated with higher moisture content, higher seed surface area to volume ratio, and higher coefficient of velocity of germination, coefficient of variation of germination time, and germination index. Additionally, the relatively tolerant genotypes showed higher seedling vigor. The results of the second experiment demonstrated superior growth performance in relative tolerant genotypes compared to the sensitive groups. Young plants of coffee belonging to relatively tolerant genotypes exhibited higher growth performance than the sensitive genotypes, with a net assimilation rate strongly correlated to relative water content, leaf number, stomatal conductance, and chlorophyll-a. In addition, a strong correlation was exhibited between the growth of young coffee plants and the surface area to volume ratio of the seeds, as well as the germination percentage. The seedling vigor index showed a strong correlation with net assimilation rate, chlorophyll content, seedling growth, and cell membrane stability. Furthermore, principal component analysis illustrated distinct clustering of genotypes based on their germination and growth-physiological performance. Overall, the findings of this study suggest the importance of seed traits, germination, and post-germination events are integral factors in determining drought tolerance and sensitivity, as well as the growth and physiological responses of adult coffee plants.

Analyzing big data poses a great challenge for numerous researchers to explore the data structure. Dimension reduction methods can be used to reduce data dimensionality, taking it from occupying a high-dimensional space to existing in a lower-dimensional space while retaining as much information as possible. Principal Component Analysis is one of the most popular used to reduce the dimensional space. The bootstrap sample is obtained by randomly sampling n times with replacement from the original sample, the method provides easy tool to understand the interactive component and develop the process. There are not enough researches discussed the stability of PCA method using bootstrap method. In this paper, the bootstrap method is used to analyze the stability of PCA results and to estimate the number of PCA in efficient way. The method is used to estimate the number of PCA that needed to classify the data set, and the effectiveness of the discussed techniques is demonstrated through real data sets.

An approach of implementing X-bar and R control charts as a statistical control tool to monitor changes in the melting profile of fresh and stored flaxseed oils by differential scanning calorimetry (DSC) was used. Phase transition melting profiles were collected after 0, 2, 4, 6 months of storing flaxseed oils, originated from five different cultivars. Four peaks at around -36, -30, -25, -12 °C were identified using the deconvolution analysis procedure, which enabled data to be collected on peak temperature (T), peak height (h) and the peak area (A), as well as the ratio calculated from these parameters. Control charts of DSC parameters, linked to the second peak (h2, A2) and calculated ratios of those parameters showed an increasing or decreasing trend within the storage time, thus were considered to be indicators of oil deterioration. Since DSC parameters related to the first peak (h1, A1) and third peak (h3, A3) remained unchanged within storage, they were established as the markers of flaxseed oil authenticity.

The frequency synthesizer is a critical component in Cs beam clock technology. In this paper, we present a demonstration of a direct microwave frequency-synthesis chain for a cesium-beam atomic clock, which utilizes frequency multiplication and a dual-phase-locked loop mode. A detailed analysis of the frequency-synthesis chain is conducted, and a mathematical model is established. The phase settling time and system stability are simulated, measured, and verified. The experimental results for the phase settling time align with the simulation outcomes. The phase settling time can be adjusted within the range of 644.5 µs to 1.5 ms, and the absolute phase noise values are -63.7 dBc/Hz, -75.7 dBc/Hz, -107.1 dBc/Hz, and -122.5 dBc/Hz at 1 Hz, 10 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Additionally, the Ramsey fringes are detected, and the Allan deviations of the 10 MHz output from the cesium-beam atomic clock are measured to be 2.99×10−12 at 1s and 8.02×10−14 at 10,000 s.

Accidents at mining enterprises, including tailing dumps, pose significant threats to human lives, structures, and the environment. This study focuses on designing, constructing, and operating tailing dumps in Siberia's northern region. To ensure safety and minimize environmental impacts, comprehensive scientific monitoring and research were conducted at all stages, including design, construction, operation, and disposal. The aim was to create a uniform mass within the dam body, requiring understanding of the tailings' structure and technological characteristics during placement. Parameters like particle size, distribution, density, and moisture content were considered to assess tailings' physical and geometric properties. Estimated monitoring was introduced as a permanent model to quickly assess the stability of hydrotechnical constructions. This involved monitoring changes in exploitation properties, structure height, beach length, and water levels. A controlled inwashing technology for subsequent dam layers was developed. Complex research facilitated the formulation of an estimated monitoring methodology and an algorithm for tailing dam formation. Practical application demonstrated high reliability and confirmed load-bearing capacity, allowing for the forecast of dam stability and safe execution. Findings led to alterations in work techniques, ensuring safe and efficient operation of tailing dams.

Background: The Stability Index estimation algorithm was derived and applied to develop and implement a balance ability diagnosis system that can be used at daily life. Methods: The system integrated an approach based on sensory function interaction, called the clinical test of sensory interaction with balance (CTSIB). The piezo-resistive force mat was fabricated, and a Stability Index prediction algorithm was developed and applied using the center of pressure (CoP) variables. The Stability Index prediction algorithm derived a CoP variable for 103 elderly people by Nintendo Wii Balance Board (WBB) to predict the Stability Index of the Balance System (Biodex SD). And, the accuracy was confirmed through the correlation between the real and predicted value. Results: As a result of testing with the test-set, the linear regression model confirmed that the r value ranged between 0.943 to 0.983. To confirm the similarity between the WBB and flexible force mat, each measured CoP value was input and calculated into the developed regression model, and the result of the correlation coefficient validation ​​confirmed an r value of 0.96. Conclusion: The system developed in this study will be applicable to the daily life of the home in the form of a floor mat.

Despite the immense application of combustion in reactive materials, one of the challenges people are facing globally is the auto-ignition of such materials, resulting in fire and explosion hazards if proper measures are not considered. To avoid this unfortunate occurrence, a mathematical model describing the thermal decomposition of combustible polymer material in a rectangular stockpile is formulated. A nonlinear momentum equation is provided with the assumption that the combustible polymer follows Carreau constitutive relation. The chemical reaction of the polymer material is assumed exothermic; therefore, Arrhenius’s kinetic theory is considered in the energy balance equation. The bivariate spectral local linearization Scheme (BSLLS) is utilized to provide a numerical solution for the dimensionless equations governing the problem. The obtained results are validated by the collocation weighted residual method (CWRM) and a good agreement is achieved. Dimensionless velocity, temperature, and thermal stability results are presented and explained comprehensively with suitable applications.

Proliferating cell nuclear antigen (PCNA) is the key regulator of human DNA metabolism. One important interaction partner is p15, involved in DNA replication and repair. Targeting the PCNA-p15 interaction is a promising therapeutic strategy against cancer. Here, a Förster resonance energy transfer (FRET)-based assay for the analysis of PCNA-p15 interaction was developed. Next to the application as screening tool for the identification and characterization of PCNA-p15 interaction inhibitors, the assay is also suitable for the investigation of mutation-induced changes in their affinity. This is particularly useful for analysing disease associated PCNA or p15 variants at the molecular level. Recently, the PCNA variant C148S has been associated with Ataxia-telangiectasia-like disorder type 2 (ATLD2). ATLD2 is a neurodegenerative disease based on defects in DNA repair due to an impaired PCNA. Incubation time dependent FRET measurements indicated no effect on PCNAC148S-p15 affinity, but on PCNA stability. The impaired stability and increased aggregation behaviour of PCNAC148S was confirmed by intrinsic tryptophan fluorescence, DSF and AF4 measurements. The analysis of the disease associated PCNA variant demonstrated the versatility of the interaction assay as developed.

A series of alpha,omega-bis(o-methoxyphenyl)arenes were prepared through Suzuki-Miyaura coupling reactions of dibromoarenes with o-methoxyphenyl boronic acid. P2O5-CH3SO3H-mediated direct polycondensation of alpha,omega-bis(o-methoxyphenyl)arenes with trans-1,4-cyclohexanedicarboxylic acid proceeded regioselectively to afford 1,4-cyclohexanediyl-containing aromatic polyketones. The resulting aromatic polyketones have high Tg and excellent solubility in typical organic solvents. In addition, the polyketone films fabricated by solution casting method are more colorless and transparent than those without cyclohexanediyl units.

This study investigates the transition from surface to underground mining at the Sepon Gold mine. The stability of surface slopes is assessed prior to commencing underground operations. Stope mining is adopted based on ore body characteristics and geological features. Finite element numerical analysis, employing the Generalized Hoek-Brown criterion, evaluates slope stability for surface slopes and opening stopes. The pit design comprises a 70° slope angle, 20 m height, and 10-15 m safety berm, meeting stability requirements with a factor of safety of 2.46. Underground mining design includes a 62° ore body dip, 50 m thick crown pillar to prevent surface subsidence, and 5 m wide, 5 m high stopes. Sill pillars are left for support after each level excavation. Rock bolts are employed in specific stope areas where is necessary, with continuous monitoring for surface deformation. The study analyzes the influence of stope sizes on pit wall and pit bottom stability, identifying slope failures near the hanging wall close to the pit bottom during underground mining. A slight increase in the displacement zone is observed on the upper crest of the top footwall. Overall, the findings demonstrate successful stability in the transition from surface to underground mining at Sepon Gold mine.

Creep is a fundamental property naturally exists in some types of rock, which is significant for the long-term stability of roadways during the mining process. In this paper, the long-term strength of coal and rock were obtained via laboratory experiments, and a Cvisc elasto-viscoplastic model was adopted and introduced in FLAC3D, based on the 3101 transport roadway in Hongqinghe Coal Mine, to investigate the influence of creep on the stability of deep-high stress roadway. The test results show that the long-term strength of 3-1 coal and sandy mudstone, respectively, is 18.65 MPa, 39.95 MPa. The plastic zone, the deformation, and the damage of roadway surrounding rock behave an obvious increase after being excavated for 720d as the creep model was chosen. The plastic zone failure with models shear-p (1090.7 m3), shear-n (381.7 m3), tension-n (98.4 m3), and tension-p (30.8 m3), the damage value has an obvious increment of increased 21.2% (0.053), the deformation increases in the order is two-sidewalls (1978 mm), roof (907 mm), floor (101 mm). The creep of the roadway can be divided into three stages: the accelerating stage, the decaying stage, and the stable stage. The creep speed of each stage is greatly affected by the presence or absence of anchor spray support: the creep speed of the bare roadway roof, roadway side, and floor stability, respectively, is 1.01, 1.02, and 0.12 mm/d; After anchor spray support, the creep velocity, correspondingly, decreased to 0.69, 0.37, and 0.12 mm/d, and the amount of surrounding rock damage decreased from 0.302 to 0.243. This indicates that the anchor spray support can significantly reduce the creep effect of the roadway. The Cvisc creep model was verified reliable and can provide guidance for deep high-stress coal roadway support.

MnO₂ nanoparticles are considered nanozymes with intrinsic peroxidase-like activity and there are several reports on their application in the field of nanozyme-based sensing and detection, however, up to now, there is no report on the investigation of their biochemical and kinetics properties toward enzyme-mediated oxidations. Hence, in this work, the MnO₂ nanozymes were synthesized and characterized with different characterization methods. Thereafter, their biochemical properties including pH stability, thermal stability, and salt stability as well as their kinetics perfromances were evaluated toward n-electron irreversible oxidation of 3,3’-diaminobezedine. The results showed that the as-prepared nanozymes reveal their maximal enzyme-like activity over a wide pH range of 3.0-6.0 at a temperature of 23-25 ℃ toward oxidation of 3,3’-diaminobezedine. Besides, the salt stability studies exhibited that the as-mentioned nanozymes can save their maximal activity over a wide range of high salt concentrations over 3-7 M of NaCl. Moreover, the kinetics studies revealed a K_m as low as 1.6 mM and a V_max as high as 47 nM sec^-1 for the MnO₂ nanozymes toward irreversible oxidation of DAB to produce the brown-colored polyDAB.

Soil aggregates, as the basic component of soil, make great contributions to the stability of soil structure and soil carbon (C) sequestration. Recently, grassland is experiencing continuous grazing, which greatly affects soil aggregation and soil C storage. However, how soil aggregates and soil C in different grassland respond to grazing remain unclear. In this study, three national fenced grassland monitoring field stations which represented mountain meadow (MM), temperate steppe (TS), temperate steppe desert (TSD) were selected, soil samples at 0–10 cm depth of inside and outside the fence were collected to explore the effect of grazing and grassland type on composition, stability and nutrients of soil aggregates. The results showed that the bulk soil organic carbon (SOC), total nitrogen (TN), total phosphorus (TP), available nitrogen (AN) and available phosphorus (AP) varied greatly among the three grassland types, with the highest values in MM. Soil aggregates composition showed significantly response to both grassland type and grazing, especially the proportion of soil aggregates &gt;2 mm, which significantly decreased 51.68% on average in grazing plots compared with fenced plots, whereas sharply decreased in MM and TSD. A significant decrease (on average 25.08%) of the mean weight diameter (MWD) of soil aggregates under grazing was detected across all grassland types. The effect of grazing on nutrients in macroaggregates (&gt;0.25 mm) was greater than that in microaggregates (&lt;0.25 mm). Aggregate-associated SOC concentration decreased under grazing in MM and TSD, however, SOC density showed different response to grazing across all grassland types, with minor effect on MM, decreasing SOC density in TS and increasing on TSD, respectively. The magnitude of grazing effect size on aggregate-associated SOC varied in different soil particle size, with greater response in aggregates &gt; 2 mm and the biggest value in TDS. In addition, correlation analysis showed that MWD of soil aggregates had significant negative correlation with soil bulk density, but significant positive correlation with SOC, TN and TP concentration. Results of RDA showed that BD, soil nutrients were the main influence factors of the composition and stability of aggregates. Overall, grazing had significant influence on soil aggregation, stability and SOC, played a crucial role in grassland soil stability and the accumulation of SOC.

40 years of cloud observations are available globally from satellites allowing derivation of climate data records (CDRs) for climate change studies. The aim of this study is to investigate how stable these cloud CDRs are and whether they qualify stability requirements recommended by the WMO’s Global Climate Observing System (GCOS). We also investigate robust trends in global total cloud amount (CA) and cloud top temperature (CTT) that are significant and common across all CDRs. The latest versions of four global cloud CDRs, namely CLARA-A3, ESA Cloud CCI, PATMOS-x and ISCCP-HGM, are analysed. This assessment finds that all three AVHRR based cloud CDRs satisfy even the strictest GCOS stability requirements for CA and CTT when averaged globally. While CLARA-A3 is most stable in global averages, PATMOS-x offers the most stable CDR spatially. While we find these results highly encouraging, there however remain large spatial differences in the stability of and across the CDRs. All four CDRs continue to agree on the statistically significant decrease in global cloud amount over the last four decades, although this decrease is now weaker compared to the previous assessments. This decreasing trend is stabilizing or even reversing in the last two decades; the latter is seen also in MODIS-Aqua and CALIPSO GEWEX datasets. Statistically significant trends in CTT are observed in global averages in the AVHRR-based CDRs, but the spatial agreement in the sign and the magnitude of the trends is weaker compared to those in CA. We also present maps of Common Stability Coverage and Common Trend Coverage that could provide a valuable metric to carry out an ensemble-based analysis of the CDRs.

In the last years, a recent growing line of research has been developed with fruitful results by using fractional and conformable derivatives in the iterative procedures of classical methods for solving nonlinear equations. In that sense, the use of conformable derivatives has shown better behavior than fractional ones, not only in the theory, but also in the practice. In this work, we adapt the approximation of conformable derivatives in order to design the first conformable derivative-free iterative schemes to solve nonlinear equations: a Steffensen’s type method and a Secant type method; the latter with memory. Convergence analysis is made, preserving the order of classical cases, and the numerical performance is studied in order to confirm the results in the theory. It is shown that these methods can present some numerical advantages versus their classical partners, with wide sets of converging initial estimations.

In this paper, an iterative procedure to find the solution of a nonlinear structural model is introduced. The model presents different multiplicities where parameters are randomly selected within a solvability region. To achieve this aim, a class of multipoint fixed-point iterative schemes for single roots is modified to find multiple roots, reaching the fourth order of convergence. Complex discrete dynamics techniques are employed to select the members with the most stable performance. The structural problem, as well as some academic problems involving multiple roots, are solved numerically to verify the theoretical analysis, robustness and applicability of the proposed scheme.

Non-normal mode stability analysis has long been employed to study linear transient characteristics of wall bounded shear flows. However, the application of this approach to investigate shear flows with stratified thermal conditions (STCF) has received limited attention. This paper examines thermal effects on Taylor-Couette flow. The results in this study indicate the possibility of a subcritical bifurcation in stratified Taylor-Couette flow.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Osteoporotic spinal fractures represent an increasingly widespread health problem in our aging society. We aimed to investigate the treatment options for low-energy spinal fractures in the el-derly and their impact on mortality, focusing on surgical stabilization using minimally invasive and open techniques. We evaluated 1356 patients over 50 years of age with compression frac-tures sustained due to low energy trauma treated at a single trauma center. We compared the mortality of patients following stable and operated/non-operated unstable compression frac-tures and the eligibility to surgery using the open and minimally invasive approach. The pa-tients received surgical or conservative care according to severity and eligibility to surgery. The mortality hazard ratio of patients who underwent screw fixation was 1.02 (P > .91), of patients who refused surgery was 1.68 (P < .001) and that of patients with anesthesiological contraindica-tion was 1.57 (P = .08), compared to conservatively treated patients with stable fractures. The dif-ference in mortality between open and minimally invasive surgeries was not significant, but the number of patients eligible for surgery with the minimally invasive procedure was significantly higher (OR: 0.25; P < .001). Spinal stability after fractures may be an important predictor of sur-vival in patients with low-impact fractures.

In current work, we illustrate the effect of adding small amount of Carbon to very common Co2MnSi Heusler alloy based-glass coated microwires. A significant change in the magnetic and structure structural properties has observed for the new alloy Co2MnSiC compared to the Co2MnSi alloy. The magneto-structural investigations have performed to clarify the main phys-ical parameters i.e., structural & magnetic at a wide range of measuring temperature. The XRD analysis illustrated the well-defined crystalline structure with average grain size (Dg = 29.16 nm) and a uniform cubic structure with A2-type compared to the mixed L21 and B2 cubic structures for Co2MnSi-based glass coated microwires. The magnetic behaviour has investigated at a tem-perature range (5 to 300 K) and an external applied magnetic field (50 Oe to 20 kOe). The adding of small amount of Carbon to the Co2MnSi matrix enhance the magnetic thermal stability, where the thermomagnetic behaviour of Co2MnSiC glass-coated microwires show a perfect stable be-haviour for a temperature range from 300 K to 5 k, the differences between the coercivity value is only 0.3 Oe compared to 4 Oe for Co2MnSi-sample. In addition, M-H loops measured at tempera-ture below 50 K show unsaturated loops; meanwhile the Co2MnSi loops shows a strong antifer-romagnetic coupling for the loops measured below 50 K. By studying the field cooling (FC) and field heating (FH) magnetizations curves at a wide range of external applied magnetic field we detected a critical magnetic field (H = 1 kOe) where FC and FH curves have a stable magnetic behavior for Co2MnSiC sample, such stability does not find in Co2MnSi sample. We proposed a phenomenal expression to estimate the magnetization thermal stability, ΔM (%), of FC and FH magnetization curves and the maximum value is detected at the critical magnetic field where ΔM (%) ≈ 98 %. The promising magnetic stability of Co2MnSiC glass-coated microwires with tem-perature is due to the changing of the microstructure induced by adding Carbon, as the A2-type structure show a unique stability by variation the temperature and the external magnetic field. In addition, a unique internal mechanical stress, which induced during the fabrication process and plays on controlling magnetic behavior with temperature and external magnetic field. The ob-tained results make Co2MnSiC promising candidate for magnetic sensing devices based Heusler glass-coated microwires.

The structural stability of γ-boron is investigated using Raman spectra under high pressures up to 126 GPa at ambient temperature. The pressure dependence of all the Raman-active modes of the γ-boron is reported. We also observe amusing changes within the B3g and B1g Raman-active vibrational modes, which results in the phenomenon of merging first and then separating of the Raman peaks. In addition to the Raman measurements, the changes in crystal structure and force constants are calculated to reasonably explain the discrepancy between the two Raman modes in response to pressure. The results of the continuous shifts for all Raman modes with increasing pressure indicate that γ-boron remains stable below this pressure value, with no changes in either symmetry or structure.

Patterning, stability, and dispersion of the semiconductor quantum dots (scQDs) are the three issues strictly interconnected for successful device manufacturing. Recently several authors adopted direct optical patterning (DOP) as a step forward in photolithography to position the scQDs in a selected area. However, the chemistry behind the stability, dispersion, and patterning has to be carefully integrated to obtain a functional and therefore, commercial device. In this review are described different chemical strategies suitable to stabilize the scQDs both at a single level and as an ensemble with a special focus on the ones compatible with direct optical patterning (DOP). With the same purpose, the scQDs dispersion in a matrix was described in terms of the scQDs surface ligands interactions with the matrix itself. The chemical processes behind the DOP are illustrated and discussed for five different approaches that consider together stability, dispersion, and the patterning itself of the scQDs.

Alkenyl Succinic Anhydride (ASA) is a sizing agent used in papermaking to increase the water repellency of paper. Almost 60 years after the introduction of the chemical in papermaking, scientists still have differing views on how ASA interacts with cellulose. Several experiments were conducted to bring more clarity to the ASA sizing mechanism, especially on the contentious question of ASA-cellulose covalent bonding or the esterification reaction between ASA and cellulose during papermaking. Herein, research papers and patents, including experiments and results, from the1960’s to 2020 were reviewed. Our investigation revealed that the ester bond formation between ASA and cellulose is insignificant and is not a prerequisite for sizing effectiveness; the main ASA related material found in sized paper is hydrolyzed ASA or both hydrolyzed ASA and ASA salt. In addition, ASA emulsion stability and ASA emulsion retention are important for sizing efficiency improvement.

Hepatitis B is a potentially life-threatening infectious disease caused by the hepatitis B virus (HBV), which affects the liver. Every year, about 390,000 people die from HBV-related diseases in China, about 86 million people are carriers of HBV, accounting for about 6% of the total population, and 30 million people are chronically infected. From 2002 to 2007, though China government launched “The Global Alliance for Vaccines and Immunization (GAVI)” program to reduce HBV infection in children, but the number of hepatitis B cases in China remains high. Reasonable estimation of potential HBV carriers is crucial to prevention and control the spread hepatitis B virus. This study is based on the case data from the National Bureau of Statistics of China from 2003 to 2021. We build a dynamic model that includes potential hepatitis B virus carriers, use nonlinear least squares and genetic algorithms to fit the parameters in the model, and calculate the reproduction number of hepatitis B virus transmission in the population and obtain R_c=1.741. The number of potential hepatitis B virus carriers is estimated to be 449,535 (95%CI [415651 to 483420]) based on our model, which is 30.49% of the total number of hepatitis B cases, and the simulation results show the number of chronic hepatitis B incidence decreases as the vaccination rate α increases, increasing α by 20%, the number of chronic hepatitis B incidence decreases by 169,469 on average.

In recent years, graphene has received so much attention because of its superlative properties and its potential to revolutionize electronics especially in VLSI. This study analyzes the effect of single event upset (SEU) in SRAM cell which employs metal-oxide semiconductor type graphene nano-ribbon field effect transistor (MOS-GNRFET) and compares the results respectively with another SRAM cell designed in PTM 10nm FinFET node. Our simulation show there is a change in data stored in the SRAM after heavy ion strike. However, it recovers from radiation effects after 0.46 ns for GNRFET and 0.51 ns for FinFET. Since the degradation observed in Q and Qb of GNRFET SRAM are 2.7X and 2.16X as compared to PTM nano-MOSFET, we can conclude that GNRFET is less robust to single effect upset. In addition, the stability of SRAM can be improved by increasing the supply voltage VDD.

The newly developed friction-interlocking armor unit, called ‘Double cube’ (DC), has been designed to improve the performance of the concrete armor unit used in river/marine structures against currents/waves actions. DC unit, is an octagonal-shaped block, made up of two parts: an upper cube set on a lower base that is either square or octagonal in shape. The innovative design aims to provide a good performance in terms of stability, high tolerance placement with various contact points and ease of placement. DC’s shape and placement enhance the stability by bringing the center of gravity closer to the underlayer and providing a large contact surfaces with surrounding blocks that reduce the chance of extraction and limit movements (rocking, lifting) via "keystone" effect. The characteristics of this new unit provides a relatively high hydraulic stability number for the armor layer (NS=2.9), a favorable hydraulic performance due to energy dissipation from turbulence and aeration, as well as a high roughness coefficient (γf≈0.46) helping to reduce the overtopping.

Trace metals are essential elements that play key roles in a number of biochemical processes governing human visual physiology in health and disease. Several trace metals, such as zinc, have been shown to play important roles in the visual phototransduction process. In spite of this, there has been little research conducted on the direct effect of trace metal elements on the visual pho-toreceptor rhodopsin. In the current study, we have determined the effect of several metal ions, such as iron, copper, chromium, manganese, and nickel on the conformational stability of rho-dopsin. To this aim, we analyzed, by means of UV-visible and fluorescence spectroscopic methods, the effects of these trace elements on the thermal stability of dark rhodopsin, the stability of its active Metarhodopsin II conformation, and its chromophore regeneration. Our results show that copper prevented rhodopsin regeneration and slowed down the retinal release process after il-lumination. In turn, Fe3+, but not Fe2+, increased the thermal stability of the dark inactive con-formation of rhodopsin, whereas copper ions markedly decreased it. These findings stress the important role of trace metals in retinal physiology at the photoreceptor level, and may be useful for the development of novel therapeutic strategies to treat retinal disease.

Keywords: artificial bone; conical implants; cylindrical implants; dental implants; implant stability quotient; insertion torque; polyurethane; post-extraction sites; removal torque.

In real-life scenario, there are many mathematical tools to handle the incomplete and imprecise data. One of them is the fuzzy approach. This article aims to contribute to the literature of fuzzy multi-objective dynamic programming issues involving the fuzzy objective functions. The piecewise quadratic fuzzy numbers characterize these fuzzy parameters. Some basic notions in the problem under the α-pareto optimal solution concept is redefined and analyzed to study the stability of the problem. Furthermore, a technique, named as enhancing decomposition approach, is presented for achieving a subset for the parametric space that contains the sameα-pareto optimal solution. For a better understanding and comprehension of the suggested concept, a numerical example is provided.

This paper proposes an imperfectly vaccinated SVEIR model for latent age. We calculate the equilibrium points and basic reproduction number of the model. The asymptotic smoothness, uniform persistence and the existence of the attractor of the semi-flow generated by the solutions of the system are addressed. Moreover, using LaSalle’s invariance set principle and constructing Volterra-type Lyapunov functions, we can prove the global asymptotic stability of both the disease-free equilibrium and the endemic equilibrium of the model. The conclusion is that if the basic reproduction number R0 is less than one, the disease will gradually disappear. On the other hand, if the number is greater than one, the disease will become endemic and persist. Finally, measures that can effectively control the ongoing transmission of the disease have been obtained.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Transition delaying is of great importance for the drag and heat flux reduction of hypersonic flight vehicles. The first mode within low frequency and the second mode within high frequency exist simultaneously during the transition of hypersonic boundary layer. This paper proposes a novel bi-frequency synthetic jet to suppress low- and high-frequency disturbances at the same time. Orthogonal table and variance analysis are used to compare the control effects of jet with different frequencies, amplitudes and positions. Linear stability analysis results show that, low frequency synthetic jet can suppress the first mode when it is arranged upstream of synchronization point, while the second mode control effect is relatively weak. The higher the high frequency is, the stronger the suppression effect is on the first mode. For the second mode, the suppression effect is only at f2=89.09kHz. The larger the amplitude, the weaker the promoting effect for the first mode and the second mode, and the more obvious the suppressing effect. For the cases with synthetic jet downstream of synchronization point, all levels of the three parameters promote the unstable mode. In terms of the growth rate with the spanwise wave number, the control effect of the same factor and level under different spanwise wave number is different. In order to obtain the optimal control effect on transition, the three factors and the arrangement position of the synthetic jet should be selected as follows: the position is arranged in the upstream, with f1 = 17.82kHz, f2 = 89.9kHz, a =0.007, so that the maximum growth rate of the first mode is reduced by 9.06% and that of the second mode is reduced by 1.28% compared with the uncontrolled state.

Extracts of Cordyceps militaris which possess the bioactive capacity such as antimicrobial activity and DPPH-free radical scavenging capacity, are applied to the serum product. This finished serum product has been evaluated the in vitro bioactivity and the stability with expect to find out a good extract with a suitable percentage used for serum product as natural materials on preservatives and antioxidation.

Converting biowaste into biochar and subsequently putting it into the soil are considered to be an effective approach to sequestrate carbon (C). However, biochar will inevitably undergo the aging process in soil, which influences its stability, and ultimately threatens its carbon sequestration ability. This study selected CaCl2 as exogenous additive of sewage sludge and bone dreg to quantify both surface C and bulk C stability in Ca-rich biochars under three aging processes (dry-wet aging, freeze-thaw aging, and natural aging in farmland soil), and revealed the influence mechanisms of exogenous Ca on biochar stability. Results showed that after dry-wet aging (25 rounds), freeze-thaw aging (25 rounds), and natural aging in different farmland soils (5 months), oxidized surface C in Ca-rich biochar decreased by 10~23%, 28~41%, and 0~74%, respectively, compared to that in pristine biochar, while oxidized bulk C decreased by 6~10%, 0~1%, and 0~35%, respectively. Under three aging processes, the surface C and bulk C stability in Ca-rich biochar were superior to that in corresponding pristine biochar, which was attributed to the “protective effect” of Ca-containing crystals on biochar surface, including CaO, Ca5(PO4)3Cl, Ca5(PO4)3(OH), Ca8H2(PO4)6·H2O and Ca10(PO4)6(OH)2. These Ca-containing crystals could block the connection between biochar-C and the external oxidizing environment, intervening the oxidation of C-C/C=C in biochar, but also prevented aging from damaging C structure of biochar, reducing the generation of fragmented structure. By comprehensively assessing surface C and bulk C stability under three aging processes, final C sequestration in Ca-rich biochar increased to 27~80%, compared to that in pristine biochar (23~74%). Therefore, Ca-rich biochar is more dominant than pristine biochar, considering C sequestration potential during long-term aging in soil.

The main objective of this study is to find out the influence of cooperation and intra-specific competition in escaping predation through refuge of the prey population and the effect of the two intra-specific interactions on the dynamics of prey-predator systems. For this purposes, two mathematical models with Holling type-II functional response function have been proposed and analyzed. The first model includes cooperation among prey populations whereas the second one incorporates intra-specific competition. Existence conditions and stability of different equilibrium points of both models have been carried out for the qualitative behaviour of the systems. Refuge through intra-specific competition has a stabilizing role, whereas cooperation has a destabilizing role on the system dynamics. Periodic oscillations are observed in both the systems through Hopf bifurcation. From the analytical and numerical findings, we conclude that intra-specific competition affects the prey population and continuously checks the refuge class under a critical value, and thus it never becomes too large to cause predator extinction due to food scarcity. Conversely, cooperation leads maximum individuals to escape predation through the refuge so that predators will suffer from low predation success.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

Bread wheat (Triticum aestivum L.) is one of the world's most important staple food crop providing 20% global energy and dietary proteins. It is widely grown in sub-tropical and tropical areas and as such exposed to heat-stress especially at grain filling period (GFP). Global warming has further affected its production and productivity in these heat-stressed environments. We examined the effect of heat-stress on 18 morpho-physiological and yield-related traits in 96 bread wheat accessions. Heat susceptibility index (HSI <0.60) and yield stability (i <0.55) used as criteria for selecting the tolerant accessions. Heat-stress, imposed by delayed sowing, decreased crop growth and GFP, and as a result reduced morphological and yield-related traits, namely days to 50% anthesis, plant height, peduncle length, flag-leaf area, spike length, spikelets per spike, grain length and width, thousand grain weight (TGW), harvest index and yield. The reduction in the trait values was severe in susceptible accessions (48.2% yield reduction in IC277741) than the tolerant. Physiological traits like chlorophyll content, canopy temperature depression (CTD), normalized difference vegetation index (NDVI), plant waxiness and leaf rolling showed higher expression in the tolerant accessions under heat-stress. Scanning electron microscopy of matured wheat grains revealed ultrastructural changes in endosperm and aleurone cells caused due to heat-stress. The reduction of size and density of large starch granules is the major cause of yield and TGW decrease in the heat-stress susceptible lines. The most stable and high-yielding accessions namely IC566223, IC128454, IC335792, EC576707, IC535176, IC529207, IC446713 and IC416019 were identified as the climate-smart germplasm lines. Germplasm lines possessing desirable traits were selected as po-tential parents for the development of bi-parental and multi-parental populations.

In this paper, we introduce a way of representing a given mapping as the sum of odd and even mappings. Then, by using this representation, we investigate the stability of various forms for the general nonic functional equation.

The main goal of the paper is to use a generalized proportional Riemann-Liouville fractional derivative (GPRLFD) to model BAM neural networks and to study some stability properties of the equilibrium. Initially, several properties of the GPRLFD are proved such as the fractional derivative of a squared function. Also some comparison results for GPRLFD are provided. Two types of equilibrium of the BAM model with GPRLFD are defined. In connection with the applied fractional derivative and its singularity at the initial time the Mittag-Leffler exponential stability in time of the equilibrium is introduced and studied. An example is given illustrating the meaning of the equilibrium as well as its stability properties.

Margarines are W/O emulsions with minimal fat and are heat treated when used for baking. Lipid oxi-dation has been identified as the major deterioration process of margarines and addition of antioxidants is necessary. Consumers are increasingly demanding that chemical antioxidants in foods be replaced by natural preservatives. A multivariate statistical study gave us oxidative stability depending on the com-position of 20 different commercial margarines and an analysis of the principal components allowed us to classify and select eight of them. This study analyzes the antioxidant capacity of six different natural ground herbs (Curcuma longa, Illicium verum, Rosmarinus officinalis, Taraxacum officinale, Thymus piperella and Thymus vulgaris) on the oxidative stability of eight selected margarines. In order to evalu-ate the oxidative stability, we determine the induction period (IP) with Rancimat assays at 120 ºC with 1.5 hours of suppression. As results, Rosmarinus officinalis increases the IP value by 73.17% with respect to its basal values, Curcuma longa, Thymus vulgaris and Thymus piperella increases it between 17% and 26% and Taraxacum officinale together with Illicium verum reduces it between 19% and 34% respec-tively. A multiple linear regression model approach shows that IP has a positive correlation with SFA, PUFA,  acids, MUFA/PUFA ratio and antioxidant activity.

In this paper, we consider the fourth-order parabolic equations with integer and fractional order time derivatives with Neumann boundary conditions. The integer order time derivatives are approximated by backward Euler difference quotients, and the fractional order time derivatives are approximated by L1 interpolation. We propose the block-centered finite difference scheme for fourth-order parabolic equations of integer and fractional order time derivatives. We prove the stability of the block-centered finite difference scheme and the second-order convergence of the discrete L2 norms of the approximate solution and its derivatives of every order. Numerical examples are given to verify the effectiveness of the block-centered finite difference scheme.

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

Primary stability is an important factor for dental implant success. In the past years, a new method for bone site preparation was introduced, named osseodensification (OD). OD produces a condensation of the trabecular portion of the bone, increasing bone-to-implant contact and primary stability. This study aims to compare the effect of OD in cylindrical and conical implants to conventional instrumentation. A total of 40 implants, divided in 4 groups, were placed in porcine tibia: cylindrical conventional (1a); cylindrical OD (1b); conical conventional (2a); and conical OD (2b). Each implant was measured for implant stability quotient (ISQ), insertion torque (IT) and removal torque (RT). Group 2b showed the higher values for each of the evaluated parameters; groups 1b and 2b showed better results than 1a and 2a, respectively. Regarding IT and RT, group 1b achieved higher values than group 2a, but not for ISQ. The inter-groups comparison showed significant difference between groups 1a vs 2a, 1a vs 2b and 1b vs 2b for ISQ, and 1a vs 1b and 1a vs 2b for RT analysis. OD resulted in improved ISQ, IT and RT of both cylindrical and conical implants. Conical implants groups showed higher ISQ, but cylindrical OD resulted in higher IT and RT, compared to conical conventional ones.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

Tolman VII solution \citep{ref-journal 2} is an exact analytic solution to the Einstein field equations describing the space-time of a static spherically symmetric distribution of matter. The solution has been shown to be capable of describing the interior of compact objects like neutron stars. Generalized \cite{ref-journal 13} and modified \cite{ref-journal 10} versions of the solution are also available in the literature, which have been subsequently developed to accommodate more realistic descriptions of neutron stars. The stability of the modified Tolman VII solution has recently been analyzed by Posada {\em et al} \cite{ref-journal 9 }, who evaluated a critical value of the adiabatic index above which the stellar configuration becomes unstable against radial oscillations. In this paper, making use of the generalized version of the Tolman VII solution, we prescribe an upper bound on the compactness ($M/R$) beyond which the star becomes unstable. Our investigation is based on the stability analysis of a star against radial oscillations developed by Chandrasekhar \cite{ref-journal 1}. The analysis brings out to attention the role of a particular model parameter in the generalized Tolman VII solution which can be linked to the inhomogeneity of the matter distribution vis-a-vis equation of state (EOS).

The sustainable development of innovative eco-friendly multifunctional nanocomposites, possessing superior characteristics, is a noteworthy topic. Novel semi-interpenetrated nanocomposite films based on poly(vinyl alcohol) covalently and thermally crosslinked with oxalic acid (OA), reinforced with a novel organophosphorus flame retardant (PFR-4) derived from co-polycondensation in solution reaction of equimolar amounts of co-monomers, namely, bis((6-oxido-6H-dibenz[c,e][1,2]oxaphosphorinyl)-(4-hydroxyaniline)-methylene)-1,4-phenylene, bisphenol S, and phenylphosphonic dichloride, in a molar ratio of 1:1:2, and additionally doped with silver-loaded zeolite L nanoparticles (ze-Ag), have been prepared by casting from solution technique. The morphology of the as prepared PVA-oxalic acid films and their semi-interpenetrated nanocomposites with PFR-4 and ze-Ag was investigated by scanning electron microscopy (SEM), while the homogeneous distribution of the organophosphorus compound and nanoparticles within the nanocomposite films has been introspected by means of energy dispersive X-ray spectroscopy (EDX). It was established that composites with a very low phosphorus content had noticeably improved flame retardancy. The peak of the heat release rate was reduced up to 55%, depending on the content of the flame retardant additive and the doping ze-Ag nanoparticles introduced into the PVA/OA matrix. The ultimate tensile strength and elastic modulus increased significantly in the reinforced nanocomposites. Considerably increased antimicrobial activity was revealed in the case of the samples containing silver-loaded zeolite L nanoparticles.

Lead-free copper halide perovskite nanocrystals (NCs) are emerging materials with excellent photoelectric properties. Herein, we present a colloidal synthesis route of orthorhombic Cs2CuCl4 NCs with well-defined cubic shape and an average diameter of 24 ± 2.1 nm. The Cs2CuCl4 NCs exhibit bright deep blue photoluminescence, which is attributed to the Cu(II) defects. In addition, passivating the Cs2CuCl4 NCs by Ag+ can effectively improve the photoluminescence quantum yield (PLQY) and environmental stability.

Infectious diseases continue to be a significant threat to human health and civilization, and finding effective methods to combat them is crucial. In this research, we investigate the impact of awareness campaigns and optimal control techniques on infectious diseases without proper vaccines. Specifically, we develop an SIRS type mathematical model that incorporates awareness campaigns through media and treatment for disease transmission dynamics and control. The model displays two equilibria, a disease-free equilibrium and an endemic equilibrium, and exhibits Hopf bifurcation when the bifurcation parameter exceeds its critical value, causing a switch in the stability of the system. We also propose an optimal control problem that minimizes the cost of control measures while achieving a desired level of disease control. By applying the minimum principle to the optimal control problem, we obtain analytical and numerical results that show how the infection rate of the disease affects the stability of the system and how awareness campaigns and treatment can maintain system stability. This study highlights the importance of awareness campaigns in controlling infectious diseases and demonstrates the effectiveness of optimal control theory in achieving disease control with minimal cost.