This research aims to estimate the micro-motion (m-m) of ships. The problem of motion and m-m detection of targets is usually solved using synthetic aperture radar (SAR) along-track interferometry (ATI) which is observed employing two radars spatially distanced by a baseline extended in the azimuth direction. This paper is proposing a new approach where the m-m estimation of ships, occupying thousands of pixels, is measured processing the information given by sub-pixel tracking generated during the coregistration process of several re-synthesized time-domain and overlapped sub-apertures. The SAR products are generated splitting the raw data, according to a small-temporal baseline strategy, observed by one single wide-band staring spotlight (ST) SAR image. The predominant vibrational modes of different ships are estimated and results are promising to extend this application in performing surveillance also of land-based industries activities. Experiments are performed processing one ST SAR image observed by the COSMO-SkyMed satellite system.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

Currently, the clinical impact of cell therapy after a myocardial infarction (MI) is limited by low cell engraftment due to significant cell death, including apoptosis, in an infarcted, inflammatory, poor angiogenic environment, low cell retention and secondary migration. Cells interact with their environment through integrin mechanoreceptors that control their survival/apoptosis/differentiation/migration/proliferation. Optimizing these interactions may be a way of improving outcomes. The association of free cells with a 3D-scaffold may be a way to target their integrins. Collagen is the most abundant structural component of the extracellular matrix (ECM) and the best contractility levels are achieved with cellular preparations containing collagen, fibrin, or Matrigel (i.e. tumor extract). In the interactions between cells and ECM, 3 main proteins are recognised: collagen, laminin and RGD (Arg-Gly-Asp) peptide. The RGD plays a key role in heart development, after MI, and on cardiac cells. Cardiomyocytes secrete their own laminin on collagen. The collagen has a non-functional cryptic RGD and is thus suboptimal for interactions with associated cells. The use of a collagen functionalized with RGD may help to improve collagen biofunctionality. It may help in the delivery of paracrine cells, whether or not they are contractile, and in assisting tissue engineering a safe contractile tissue.

Sugar-sweetened beverages are associated with metabolic dysfunction, particularly in those with increased risk factors. Artificial sweeteners (AS) are often promoted as a healthier alternative, yet findings remain conflicting as to their effects on metabolic function. Further, there is a lack of data exploring the interaction between AS and high-fat diets (HFD). We therefore examined the effects of HFD and the AS Acesulfame-potassium (Ace-K) on glucose intolerance and adipose tissue physiology in male and female C57BL/6 mice. 40 mice were randomised to receive either a) a control diet (CDCon; standard control diet/water), b) control diet and Ace-k (CDAS; CD/7.5mM AS in drinking water), c) HFD (HFCon; HFD (45%kcal from fat)/water), or d) HF and AS (HFAS; HFD/7.5mM AS in drinking water) for 6 weeks. A HFD increased body weight in male and female mice independently of AS supplementation. AS induced sex-specific effects protecting against HFD-induced hyperglycaemia and adipocyte hypertrophy in male mice and reducing inflammatory gene expression in the adipose tissue. Conversely in females, AS induced hyperinsulinemia in HFD mice and increased expression of immune-related genes. These findings suggest that supplementation of HFD with AS exacerbates metabolic dysfunction in female mice. This work supports the importance of studying sexually dimorphic responses to an altered nutritional environment and highlights the need for further investigation into the intake of AS, particularly in those already at risk of metabolic disease such as the obese or overweight.

While laminar flow heat transfer and mixing in microfluidic geometries has been investigated experimentally, as has the effect of geometry-induced turbulence in microfluidic flow (it is well documented that turbulence increases convective heat transfer in macrofluidic flow), little literature exists investigating the effect of electrokinetically-induced turbulence on heat transfer at the micro scale. Using recently observed experimental data, this work employed computational fluid dynamics coupled with electromagnetic simulations to determine if electrokinetically-forced, low-Reynolds number turbulence could be observed in a rectangular microchannel with using Newtonian fluids. Analysis of the results was done via comparison to the experimental criteria defined for turbulent flow. This work shows that, even with a simplified simulation setup, computational fluid dynamics (CFD) software can produce results comparable to experimental observations of low-Reynolds turbulence in microchannels using Newtonian fluids. In addition to comparing simulated velocities and turbulent energies to experimental data this work also presents initial data on the effects of electrokinetic forcing on microfluidic flow based on entropy generation rates.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

Organ-on-a-Chip (OoC) systems bring together cell biology, engineering, and material science for creating systems that recapitulate the in vivo microenvironment of tissues and organs. The versatility of OoC systems enables in vitro models for studying physiological processes, drug development, and testing in both academia and industry. This paper evaluates current platforms from the end-user perspective, elaborating on usability, complexity, and robustness. We surveyed 165 peers in over 30 countries and grouped the responses according to preliminary knowledge and the source of the OoC systems that are used. The survey clearly shows that current commercial OoC platforms provide a substantial level of robustness and usability - which is also indicated by an increasing adaptation of the pharmaceutical industry but a lack of complexity can challenge their use as a predictive platform. Self-made systems on the other hand are less robust and standardized but provide the opportunity to develop customized and more complex models which are often needed for human disease modeling. This review serves as a guide for researchers in the OoC field and encourages the development of next-generation OoCs.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

Neural tissue engineering, nanotechnology and neuroregeneration are diverse biomedical disciplines that have been working together in recent decades to solve the complex problems linked to central nervous system (CNS) repair. It is known that the CNS demonstrates a very limited regenerative capacity because of a microenvironment that impedes effective regenerative processes, making development of CNS therapeutics challenging. Given the high prevalence of CNS conditions such as stroke that damage the brain and place a severe burden on afflicted individuals and on society, it is of utmost significance to explore the optimum methodologies for finding treatments that could be applied to humans for restoration of function to pre-injury levels. Extracellular vesicles (EVs), also known as exosomes, when derived from mesenchymal stem cells, are one of the most promising approaches that have been attempted thus far, as EVs deliver factors that stimulate recovery by acting at the nanoscale level on intercellular communication while avoiding the risks linked to stem cell transplantation. At the same time, advances in tissue engineering and regenerative medicine have offered the potential of using hydrogels as bio-scaffolds in order to provide the stroma required for neural repair to occur, as well as the release of biomolecules facilitating or inducing the reparative processes. This review introduces a novel experimental hypothesis regarding the benefits that could be offered if EVs were to be combined with biocompatible injectable hydrogels. The rationale behind this hypothesis is presented, analyzing how a hydrogel might prolong the retention of EVs and maximize the localized benefit to the brain. This sustained delivery of EVs would be coupled with essential guidance cues and structural support from the hydrogel until neural tissue remodeling and regeneration occur. Finally, the importance of including non-human primate (NHP) models in the clinical translation pipeline, as well as the added benefit of multi-modal neuroimage analysis to establish non-invasive, in vivo, quantifiable imaging-based biomarkers for CNS repair are discussed, aiming for more effective and safe clinical translation of such regenerative therapies to humans.

Microgrids can be used for securing power supply during network outages. Underground cabling of distribution networks is another effective, but conventional and expensive alternative to enhance reliability of power supply. This paper presents firstly an analysis method for the determination of microgrid power supply adequacy during islanded operation, and secondly, a comparison method for overall cost calculation of microgrids vs. underground cabling. The microgrid power adequacy during a rather long network outage is required in order to indicate high level of reliability of supply. The overall cost calculations consider the economic benefits and costs incurred combined for both the distribution network company and the consumer. Whereas the microgrid setup determines the islanded operation power adequacy and thus the reliability of supply, the economic feasibility results from the normal operations and services. The methods are illustrated by two typical, and even critical, case studies in rural distribution networks: an electric-heated detached house and a dairy farm. These case studies show that even in case of a single consumer, a microgrid option could be more economical than network renovation by underground cabling of a branch in order to increase reliability.

Abstract: The broad clinical use of synthetic vascular grafts for vascular diseases is limited by their thrombogenicity and low patency rate, especially for vessels with a diameter inferior to 6 mm. Alternatives such as tissue-engineered blood grafts (TEBGs) have gained increasing interest. Among the different manufacturing approaches, 3D bioprinting presents numerous advantages and enables the fabrication of multi-scale, multi-material, and multicellular tissues with heterogeneous and functional intrinsic structures. Extrusion-, inkjet- and light-based 3D printing techniques have been used for the fabrication of TEBG out of hydrogels, cells, and/or solid polymers. This review discusses the state-of-the-art research on the use of 3D printing for TEBG with a focus on the biomaterials and deposition methods.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

Colonization of distant organs by tumor cells is a critical step of cancer progression. The initial avascular stage of this process (micrometastasis) remains almost inaccessible to study due to the lack of relevant experimental approaches. Here, we introduce an in vitro/in vivo model of organ-specific micrometastases of triple-negative breast cancer (TNBC) that is fully implemented in a cost-efficient chick embryo (CE) experimental platform. The model is built as three-dimensional (3D) tissue engineering constructs (TECs) combining human MDA-MB-231 cells and decellular-ized CE organ-specific scaffolds. TNBC cells colonized CE organ-specific scaffolds in 2-3 weeks, forming tissue-like structures. The feasibility of this methodology for basic cancer research, drug development and nanomedicine was demonstrated on a model of hepatic micrometastasis of TNBC. We revealed that MDA-MB-231 differentially colonize parenchymal and stromal com-partments of the liver-specific extracellular matrix (LS-ECM) and become more resistant to the treatment with molecular Doxorubicin (Dox) and Dox-loaded mesoporous silica nanoparticles than in monolayer cultures. When grafted on CE chorioallantoic membrane, LS-ECM-based TECs induced angiogenic switch. These findings may have important implications for the diag-nosis and treatment of TNBC. The methodology established here is scalable and adaptable for pharmacological testing and cancer biology research of various metastatic and primary tumors.

Background. Sarcopenia, defined as the loss of skeletal muscle mass and function, is a major clinical problem in many chronic illnesses, in cancer and in the elderly. Exercise and adequate nutrition, peculiarly dependents on availability of essential amino acids, considered the primary strategies for prevention and treatment of protein synthetic deficits, affect both the efficient scavenging of aged and overused protein molecules and the renewal, by maintaining muscular protein synthesis. Many questions still remain about the regulation of protein syntheses and degradation. Degradation of inefficient proteins or organelles is performed by the sum of micro and macro-autophagy plus ubiquitin-proteasome system, activities known as proteostasis, necessary to preserve and promote protein masses and consequently, the body’s reserves. However, how protein synthesis is regulated, and how activation of the mTOR complex may modulate and transduce the flow of information provided by exercise and nutrition to balance proteostasis and syntheses, is far from being fully understood. We suggest that energy production and availability, thus also mitochondria, may have a pivotal role in synchronizing activity and functional outcomes of protein syntheses, and that those syntheses, since higly energy demanding, are main effectors of AMPK dependent autophagy activation by consuming ATP and producing AMP. Conclusion. While in normal conditions protein syntheses drive autophagy activation by decreasing ATP to AMP ratio, conversely autophagy may be inefficiently activated when chronic both low production and consumption of ATP would result in lowest concentrations of AMP, and therefore both blunted rates of protein syntheses and autophagy would be observed. We suggest that this functional hypothesis may explain sarcopenia in many pathological conditions , as in cancer or in aging muscles.

The retina is a complex and fragile photosensitive part of the central nervous system which is prone to degenerative diseases leading to permanent vision loss. No proven treatment strategies exist to treat or reverse the degenerative conditions. Recent investigations demonstrate that cell transplantation therapies to replace the dysfunctional retinal pigment epithelial (RPE) cells and or the degenerating photoreceptors (PRs) are viable options to restore vision. Pluripotent stem cells, retinal progenitor cells and somatic stem cells are the main cell sources used for cell transplantation therapies. The success of retinal transplantation based on cell suspension injection is hindered by limited cell survival and lack of cellular integration. Recent advances in material science helped to develop strategies to grow cells as intact monolayers or as sheets on biomaterial scaffolds for transplantation into the eyes. Such implants are found to be more promising than the bolus injection approach. Tissue engineering techniques are specifically designed to construct biodegradable or non-degradable polymer scaffolds to grow cells as a monolayer and construct implantable grafts. The engineered cell construct along with the extracellular matrix formed, can hold the cells in place to enable easy survival, better integration and improved visual function. This article reviews the advances in the use of scaffolds for transplantation studies in animal models and its application in current clinical trials.

Recent evidences support a role of menthol, a TRPM8 agonist, in enhanced energy expenditure, thermogenesis and BAT-like activity in classical WAT depots in TRPM8 dependent and independent manner. The present study was designed to analyze whether oral and topical administration of menthol is bioavailable at subcutaneous adipose tissue and is sufficient to induce desired energy expenditure effects directly. GC-FID was performed to study menthol bioavailability in serum and subcutaneous white adipose tissue following oral and topical administration. Further, 3T3L1 adipocytes were treated with bioavailable menthol doses and different parameters (lipid accumulation, “browning/brite” and energy expenditure gene expression, metal analysis, mitochondrial complex’s gene expression) were studied. No difference was observed in serum levels but significant difference was seen in the menthol concentration on subcutaneous adipose tissues after oral and topical application. Menthol administration at bioavailable doses significantly increased “browning/brite” and energy expenditure phenotype, enhanced mitochondrial activity related gene expression, increased metal concentration but didn’t alter the lipid accumulation. Further, we used pharmacological antagonism based approach to study the TRPM8 involvement in menthol effect. In conclusion, the present study provides an evidence that bioavailable menthol after single oral and topical administration is sufficient to induce “brite” phenotype in subcutaneous adipose tissue.

Layered two-dimensional (2D) graphene oxide (GO) films are integrated with micro-ring resonators (MRRs) to experimentally demonstrate enhanced nonlinear optics in the form of four-wave mixing (FWM). Both uniformly coated and patterned GO films are integrated on CMOS-compatible doped silica MRRs using a large-area, transfer-free, layer-by-layer GO coating method together with photolithography and lift-off processes, yielding precise control of the film thickness, placement, and coating length. The high Kerr nonlinearity and low loss of the GO films combined with the strong light-matter interaction within the MRRs results in a significant improvement in the FWM efficiency in the hybrid MRRs. Detailed FWM measurements are performed at different pump powers and resonant wavelengths for the uniformly coated MRRs with 1−5 layers of GO as well as the patterned devices with 10−50 layers of GO. The experimental results show good agreement with theory, achieving up to ~7.6-dB enhancement in the FWM conversion efficiency (CE) for an MRR uniformly coated with 1 layer of GO and ~10.3-dB for a patterned device with 50 layers of GO. By fitting the measured CE as a function of pump power for devices with different numbers of GO layers, we also extract the dependence of GO’s third-order nonlinearity on layer number and pump power, revealing interesting physical insights about the evolution of the layered GO films from 2D monolayers to quasi bulk-like behavior. These results confirm the high nonlinear optical performance of integrated photonic resonators incorporated with 2D layered GO films.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Background: This study aimed to describe the frequency and duration of sedentary bouts and assess the bidirectional cross-sectional associations between these characteristics and adiposity in elderly women. Methods: Data from 314 elderly community-dwelling women (mean age 66.6±6.5 years) from Czech Republic, Poland, and Slovakia were analyzed. Measures were collected in 2008–2017. Fat mass percentage (FM%) was used as an indicator of adiposity. The patterns of sedentary behaviour were monitored using an accelerometer, and ≥5, ≥10, ≥20, ≥30, ≥40, and ≥60 minute bouts were analyzed. The exponent alpha was also calculated to express the accumulation of sedentary time in bouts. We performed a multiple linear regression analysis to assess the bidirectional causal association between variables. Results: There was a significant association of FM% with time spent in bouts with a duration ≥5, ≥10, ≥20min (β ranging 0.11–0.28, p≤0.01) and the frequency of bouts with a length ≥5, ≥10, ≥20, and ≥30min (β ranging 0.03–0.74, p≤0.05) in fully-adjusted models. In contrast, a strong negative association was observed between FM% and alpha (bout distribution) in both directions (p≤0.001). Conclusions: Our results suggest that the sedentary characteristics such as bout duration, bout frequency, and distribution (alpha) are bidirectionally associated with adiposity and they should be considered in further research in older adults.

Tissue engineering has the potential for repairing large bone defects, which impose a heavy financial burden on the public health. However, difficulties with O₂ delivery to the cells residing in the interior of tissue engineering scaffolds make it challenging to grow artificial tissues of clinically-relevant sizes. This study uses image-based simulation in order to provide insight into how to better optimize the scaffold manufacturing parameters, and the culturing conditions, in order to resolve the O₂ bottleneck. To do this, high resolution 3D X-ray images of two common scaffold types (salt leached foam and non-woven fiber mesh) are fed into a Lattice Boltzmann Method fluid dynamics and reactive Lagrangian Scalar Tracking mass transfer solvers. The obtained findings indicate that the scaffolds should have maximal surface area-to-solid volume ratios, for higher chances of the molecular collisions with the cells. Furthermore, the cell culture media should be flown through the scaffold pores as fast as practically possible (without detaching or killing the cells). Finally, we have provided a parametric sweep that maps how the molecular transport within the scaffolds is affected by variations in rates of O₂ consumption by the cells. Ultimately, the results of this study are expected to benefit the computer-assisted design of tissue engineering scaffolds and culturing experiments.

Abstract : This paper presents the investigation of biomechanical behaviour of sheep heart fibre using uniaxial tests in various samples. Non-linear Finite Element models (FEA) that are utilised in understanding mechanisms of different diseases may not be developed without the accurate material properties. This paper presents uniaxial mechanical testing data of the sheep heart fibre. The mechanical uniaxial data of the heart fibre was then used in fitting four constitutive models including the Fung model, Polynomial (Anisotropic), Holzapfel (2005) model, Holzapfel (2000) model and the Four-fibre Family model. Even though the constitutive models for soft tissues including heart myocardium have been presented over several decades, there is still a need for accurate material parameters from reliable hyperelastic constitutive models. Therefore, the aim of this research paper is to select five hyperelastic constitutive models and fit experimental data in the uniaxial experimental data of the sheep heart fibre. A fitting algorithm was made used to optimally fitting and determination of the material parameters based on selected hyperelastic constitutive model. In this study, the evaluation index (EI) was used to measure the performance and capability of each selected anisotropic hyperelatic model. It was observed that the best predictive capability of the mechanical behaviour of sheep heart fibre the Polynomial (anisotropic) model has the EI of 100 and this means that it is the best performance when compared to all the other models.

HIV-1 is a complicated and perplexing virus. It infects T cells, reverse transcribes its RNA into DNA, utilizes its host DNA machinery to replicate its HIV-DNA, translates the HIV-DNA into proteins, assembles itself for a budding escape from the T cell, and rapidly mutates its conformation. Partially, due to its complexity, there remains no cure for HIV or AIDs. However, recently with the discovery of TALENs, the use of zinc fingers, and most of all the applications of CRISPR-Cas9 technology, has given researchers new hope in finding alternative gene therapies and treatments for diseases. With more focus on CRISPR-Cas9, this new and novel technology uses a guiding RNA, sgRNA, to lead a Cas9 nuclease to its target for deletion or to change that DNA site. CRISPR-Cas9 can delete point mutations and multiple DNA sites. Because CRISPR can alter DNA sequences, several scientists have conducted research into CRISPR, possibly treating more diseases such as cancer, diabetes, and even HIV. HIV-1 drew the focus of a researcher named Dr. Ebina in 2013 when he was the first to design and apply CRISPR-Cas9 to genes found in the binding sites of HIV-1, inhibiting HIV-1 gene expression. Since 2013, several other researchers have blocked HIV replication and infection through CRISPR-Cas9 targeting the receptors of T cells called the CC chemokine receptor 5 or CCR5. HIV-1 binds to the CD4 receptor of T cells, which consists of co-receptors CCR5 and CXCR4. If CCR5 expression can be removed, the HIV virus cannot bind to T-cells, blocking the initial attachment stage, and discontinuing the infection. However, there remain obstacles and issues for the CRISPR deletion of CCR5 for treating HIV-1. The issues include: 1) finding new and safe methods of CRISPR-Cas9 delivery, 2) clearing the latent HIV reservoirs, 3) improving the sgRNA design to avoid off-target mutations or deletions, and 4) effectively analyze the viral escape of HIV from CRISPR-Cas9 modifications. Therefore, the purpose of this review is to discuss possible techniques for removing the obstacles that can lessen the potential of CRISPR to delete CCR5, repressing HIV-1 into long-term remission or a functional cure.

Dental pulp tissue engineering (TE) quests to regenerate dentin/pulp complex by combining a suitable supporting matrix, stem cells, and biochemical stimuli. Such procedures foresee a matrix that can be easily introduced into the root canal system (RCS) and tightly adhere to dentin walls to assure the dentin surface's proper colonization with progenitor cells capable of restoring the dentin/pulp complex. Herein was investigated an injectable self-setting hyaluronic acid-based (HA) hydrogel system, formed by aldehyde-modified (a-HA) with hydrazide-modified (ADH), enriched with platelet lysate (PL), for endodontic regeneration. The hydrogels' working (wT) and setting (sT) times, the adhesion to the dentine walls, the hydrogel's microstructure, and the delivery of human Dental Pulp Cells (DPCs) were studied in vitro. Hydrogels incorporating PL showed a suitable wT and sT and a porous microstructure. The tensile tests showed that the breaking point occurs after 4.13 mm deformation. While in the indentation test after 1.3 mm deformation. Both breaking points occur in the hydrogel extension. The HA/PL hydrogels exhibited supportive properties and promoted cell migration toward dentin surfaces in vitro. Overall, these results support using PL-laden HA injectable hydrogels (HA/PL) as a biomaterial for DPCs encapsulation, thereby displaying great clinical potential towards endodontic regenerative therapies.

Background: PRAME, NY-ESO-1 and SSX2 are cancer testis antigens (CTAs), which in normal tissues are expressed in testicular germ cells with re-expression in numerous cancer types. Their ability to elicit humoral and cellular immune responses have rendered them promising targets for cancer immunotherapy, but they have never been studied in a large and well-characterized cohort soft tissue sarcomas (STS). Methods: On protein level, we examined PRAME, NY-ESO-1 and SSX2 expression in tumour tissues of 249 STS using immunohistochemistry. We correlated expression levels with clinicopathological parameters including Tumour-infiltrating lymphocyte (TIL) counts, grading and long- term survival. Results: Expression of PRAME, NY-ESO-1 and SSX2 was observed in 25 (10%), 19 (8%), and 11 (4%) of 249 specimens with distinct patterns for histo subtypes. Expression of PRAME was associated with shorter patient survival (p=0.005) and higher grade (G2 vs G3, p=0.001) while NY-ESO-1 expression was correlated with more favourable survival (p=0.037) and low grade (G2 vs G3, p=0.029). Both PRAME and NY-ESO-1 expression was more frequent in STS with low TILs counts. Conclusions: CTAs PRAME, NY-ESO-1 and SSX2 show distinct expression patterns in different STS subtypes. These results may guide future immunotherapeutic approaches in STS.

Tissue engineering is an emerging field of research due to its growing impact on the regeneration of tissue injured from damage and organ failure. Small hydrogel microspheres containing regenerative cells and stimulators can be used as building blocks to regenerate tissue by injecting them into damaged areas; a microneedle is used to minimize the incision and any associated infections. To address the need for production of a large number of microspheres for use in tissue engineering, we developed a 3D coaxial multi-nozzle flow-focusing device fabricated via a simple 3D-printing method that demonstrates a high rate of microsphere production per nozzle. This device has six coaxial microscale nozzles that produce hydrogel microspheres. Two individual parts—the inlet and nozzle—can be made separately by a 3D printer and bonded together using uncured photo-curable resin as glue. The dimensions of the microspheres are between 100 μm and 1200 μm. They are produced by adjusting the flow rate ratio between the dispersed and continuous media. A flow rate ratio of 180 demonstrated the highest microsphere production rate of 2.12e+5 microspheres per sec (0.25 mL/min). This microsphere production rate per nozzle is four times higher than that of currently available devices.

Purpose: to assess any differences on marginal bone loss between bone-level or tissue-level dental implants through a review of literature until September 2019. Materials and methods: MEDLINE, Embase and other database were searched by two independent authors. The search was limited to articles in English. Results: The search provided 1028 records and, after removing the duplicates through titles and abstracts screening, 45 full-text articles were assessed for eligibility. For qualitative analysis 20 articles were included, 17 articles of them for quantitative analysis. A total of 1161 patients (mean age 54,4 years) and 2933 implants were observed, 1427 (Tissue-level) and 1506 (Bone-level). The survival rate and the success rate were more than 90%, except for 2 studies with a success rate of 88% and 86.2%. No studies reported any differences between groups in term of success and survival rates. Three studies showed that BL-implants had statistically less marginal bone loss (P< 0.05). Only one study reported statistically less marginal bone loss in TL-implants (P< 0.05). In the most part of the studies, differences between implant types in marginal bone loss were not statistically significant. Conclusion: Despite to the peri-implant tissue around transmucosal implants has been reported to be inflammation-free because of the absence of bacterial infiltration in the micro-gap between the fixture and abutment, no clinical and radiological differences were highlighted between groups from the included studies after a variable period of follow-up ranged between 1 to 5 years.

This work presents the results of the experimental and theoretical study of the static pull-in of tilting actuation executed by a hybrid levitation micro-actuator (HLMA) based on the combination of inductive levitation and electrostatic actuation. A semi-analytical model to study such the pull-in phenomenon is developed, for the first time, as a result of using the qualitative technique based on the Lagrangian approach to analyze inductive contactless suspensions presented in work and a recent progress in the calculation of mutual inductance and force between two circular filaments. The obtained non-linear model, accounting for two degrees of freedom of the actuator, allows us to predict accurately the static pull-in displacement and voltage. The results of modelling were verified experimentally and agree well with measurements.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

The vast majority of patients with pancreatic ductal adenocarcinoma (PDAC) suffer cachexia. Although cachexia results from concurrent loss of adipose and muscle tissue, most studies focus on muscle alone. Emerging data demonstrate the prognostic value of fat loss in cachexia. Here we sought to identify the muscle and adipose gene profiles and pathways regulated in cachexia. Matched rectus abdominis muscle and subcutaneous adipose tissue were obtained at surgery from patients with benign conditions (n=11) and patients with PDAC (n=24). Self-reported weight loss and body composition measurements defined cachexia status. Gene profiling was done using Ion proton sequencing. Results were queried against external datasets for validation. 961 DE genes were identified from muscle and 2000 from adipose tissue, demonstrating greater response of adipose than muscle. In addition to known cachexia genes such as FOXO1, novel genes from muscle, including PPP1R8 and AEN correlated with cancer weight loss. All the adipose correlated genes including SCGN and EDR17 are novel for PDAC cachexia. Pathway analysis demonstrated shared pathways but largely non-overlapping genes in both tissues. Age related muscle loss predominantly had a distinct gene profiles compared to cachexia. This analysis of matched, externally validate gene expression points to novel targets in cachexia.

Micro channel tube (MCT) is widely employed in industry due to its excellent efficiency in heat transfer. An MCT is commonly produced through extrusion within a porthole die, where severe plastic deformation is inevitably involved. Moreover, the plastic deformation, which dramatically affects the final property of the MCT, varies significantly from location to location. In order to understand the development of the microstructure and its effect on the final property of the MCT, the viscoplastic self-consistent (VPSC) model, together with the finite element analysis and the flow line model, is employed in the current study. The flow line model is used to reproduce the local velocity gradient within the complex porthole die, while VPSC model is employed to predict the evolution of the microstructure accordingly. In addition, electron backscatter diffraction (EBSD) measurement and mechanical tests are used to characterize the evolution of the microstructure and the property of the MCT. The simulation results agree well with the corresponding experimental ones. The influence of the material’s flow line on the evolution of the orientation and morphology of the grains, and the property of the produced MCT are discussed in detail.

Mesenchymal stem cells (MSCs) showed in vitro mesoderm-lineage differentiation and self-renew capacity. However, no comparative study was reported on the biological characteristics of stem cells derived from skeletal muscle (SM-MSCs), dermal skin (DS-MSCs), and adipose tissues (A-MSCs) from a single donor in camels. The present study aimed to evaluate the influence of MSCs source on stem cell characteristics. We evaluated proliferation capacity and mesoderm-lineage differentiation potential from SM-MSCs, DS-MSCs, and A-MSCs. They showed spindle-like morphology after homogenization. The proliferation ability was no significant difference in all groups. Furthermore, the portion of the cell cycle and expression of pluripotent markers (Oct4, Sox2, and Nanog) were similar in all cell lines at passage 3. The differentiation capacity of A-MSCs into adipocytes was significantly higher than that of SM-MSCs and DS-MSCs. However, the osteoblast differentiation capacity of A-MSCs was significantly lower than that of SM-MSCs and DS-MSCs. Additionally, after osteoblast differentiation, the ALP activity and calcium content was significantly decreased in A-MSCs as compared to SM-MSCs and DS-MSCs. To the best of our knowledge, we primally established MSCs from the single camel and demonstrated their comparative characteristics including expression of pluripotent factors and proliferation, and in vitro differentiation capacity into adipocytes and osteoblasts.

This paper presents a demonstration of the feasibility of fabricating micro-cantilever harvesters with extended stress distribution and enhanced bandwidth by exploiting an M-shaped two-degrees-of-freedom design. The measured mechanical response of the fabricated device displays the predicted dual resonance peak behavior with the fundamental peak at the intended frequency. This design has the features of high energy conversion efficiency in a miniaturized environment where the available vibrational energy varies in frequency. It makes such a design suitable for future large volume production of integrated self powered sensors nodes for the Internet-of-Things.

In the last two decades, gelatin-based hydrogels have been widely used as tissue engineering scaffolds due to their excellent biocompatibility, biodegradability, easy processability, transparency, non-toxicity, and reasonable structural similarity to the natural extracellular matrix (ECM). However, intrinsic low mechanical properties of gelatin are not structurally and mechanically suitable to support cell growth and proliferation. That’s why various crosslinking strategies including physical, chemical, enzymatic and combination of them as well as networking patterns including double network, interpenetrating network and nano reinforcing mechanism have been utilized to enhance the structural stability and mechanical integrity of gelatin. In this review, the advances in modulating the mechanical properties of gelatin-based hydrogels for the design and development of structurally stable scaffolds for tissue engineering are discussed. The optimized crosslinking parameters with the adequate mechanical properties of gelatin-based hydrogels are reviewed. Gelatin-based scaffolds for a wide range of tissue engineering applications, such as bone, cartilage, cardiac, skin, and nerve tissue engineering are also outlined. Lastly, current challenges and future perspectives in this research field are presented.

The occurrence of bone-related disorders and diseases has increased dramatically in recent years around the world. Demineralized bone matrix (DBM) has been widely used as a bone implant due to its osteoinduction and bioactivity. However, the use of DBM is limited because it is a particulate material, which makes it difficult to manipulate and implant with precision, in addition, these particles are susceptible to migrate to other sites. To address this situation, DBM is commonly incorporated into a variety of carriers. An injectable scaffold has advantages over bone grafts or preformed scaffolds, such as the ability to flow and fill the bone defect. The aim of this research is to develop a DBM carrier with such viscoelastic properties to obtain an injectable bone substitute (IBS). The DBM carrier developed consisted of a PVA/glycerol network cross-linked with borax and reinforced with CaCO3 as a pH neutralizer, porosity generator, and source of Ca. The physicochemical properties were determined by the injectability test, FTIR, SEM, and TGA. Porosity, degradation, bioactivity, possible cytotoxic effect, and proliferation in osteoblasts were also determined. The results show that the developed material has great potential to be used in bone tissue regeneration

Restricted feeding is well known to affect expression profiles of both clock and metabolic genes. However, it is unknown whether these changes in metabolic gene expression result from changes in the molecular clock or in feeding behavior. Here we eliminated the daily rhythm in feeding behavior by providing 6-meals evenly distributed over the light/dark-cycle. Animals on this 6-meals-a-day feeding schedule retained the normal day/night difference in physiological parameters including body temperature and locomotor activity. The daily rhythm in respiratory exchange ratio (RER), however, was significantly phase-shifted through increased utilization of carbohydrates during the light phase and increased lipid oxidation during the dark phase. This 6-meals-a-day feeding schedule did not have a major impact on the clock gene expression rhythms in the master clock but did have mild effects on peripheral clocks. By contrast, genes involved in glucose and lipid metabolism showed differential expression. Concluding, eliminating the daily rhythm in feeding behavior in rats does not affect the master clock and only mildly affects peripheral clocks, but disturbs metabolic rhythms in liver, skeletal muscle and brown adipose tissue in a tissue-dependent manner. Thereby a clear daily rhythm in feeding behavior strongly regulates timing of peripheral metabolism, separately from circadian clocks.

Lack of reliable information on PTC industry in Sri Lanka is hampering the advancement of the technology. Hence, this study attempted to assess the current status of PTC industry in Sri Lanka in order to ascertain the type and the level of interventions needed to broaden the horizons of the industry. Data of last 05 years were collected through qualitative research methods including a questionnaire-based survey, personal interviews, etc. and personal interviews to identify product diversity, R&D, available facilities, production capacity, and markets. Information was analyzed qualitatively using descriptive statistical software to assess the current status, and identify gaps, challenges and opportunities. COVID pandemic and the economic crisis had a heavy toll on the PTC industry. Six major challenges experienced by business owners were identified as increasing capacity, opportunities to build market linkages, demand fluctuations, issues relating to awareness and insufficient support given by the government. Proper identification and screening of mother plants, determining the production capacities and marketing, knowledgeable and skilled human resources, were identified as important contributory factors for success. Development strategies identified mainly include instinctive decision making and government support. Embracing the significant trade achievements through resource reallocation, prioritization and improvisation processes at individual, family group, inter-organizational levels and across these levels need to be regulated through a responsible authority. These interpretations and recommendations of this research can be utilized both by the policy makers and public and private sector organizations for decision making purposes targeting commercial scale advancements.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

The Wolfram (W), Silicium (Si) and Molybdenum (Mo) doped Co-Cr biomedical alloy were fabricated by additive manufacturing method, which is part of powder metadology. The mixture of Wolfram (W), Silicium (Si), Chrome (Cr) and Cobalt (Co) alloy is known good wear and corrosion resistance among of biomedical applications. By addition of Molybdenum (Mo) into the structure of alloy, the structure become more stbale also increase the corrosion and wear resistance. In addition, the effects of secondary annealing process on the alloy were investigated. The microstructure of the produced alloy was analyzed by X-ray diffraction method XRD, Energy Dispersive X-Ray Analysis EDX and scanning electron microscope SEM. Moreover, Electrochemical corrosion test, micro hardness and density measurements were performed to investigate the mechanical properties of the alloy. As a result of the analyzes, the effects of Molydenum (Mo) doped and secondary annealing on the microstructure and mechanical properties of bioalloying were determined.

The cell’s capacity to integrate and respond to spatial information is a crucial feature of morphogenesis and development. The Planar Cell Polarity (PCP) pathway is a signaling mechanism, widely conserved across metazoans, providing spatial orientation along the plane of an epithelium in morphogenic processes ranging from insect wing patterning to mammalian cochleae. Although the core genes involved in the PCP pathway have been molecularly identified in the 1990s, the PCP signaling mechanism remains controversial. In this article I discuss the main players and previous models of PCP signaling reported in the literature, and propose a new model. According to it PCP is established through an homophobic signal by transmembrane protein Frizzled (Fz): 1) a Fz signal in one cell repeals Fz itself in the adjacent cell, thereby generating symmetry breaking; 2) the instructive PCP signal is conveyed through Fz interaction with atypical cadherin Flamingo (Fmi). More broadly, homophobic signaling may represent a novel mechanism for cell-cell signaling of spatial information through modulation of cell adhesion rather than canonical ligand-receptor binding.

Cannabis has developed into a multi-billion dollar industry that relies on clonal propagation of elite genetics with desirable agronomic and chemical phenotypes. While the goal of clonal propagation is to produce genetically uniform plants, somatic mutations can accumulate during growth and compromise long-term genetic fidelity. Cryopreservation is a process in which tissues are stored at cryogenic temperatures, halting cell division and metabolic processes to facilitate high fidelity germplasm preservation. In this study, a series of experiments were conducted to optimize various stages of cryopreservation and develop a protocol for long-term germplasm storage of Cannabis sativa. The resulting protocol uses a standard vitrification procedure to cryopreserve nodal explants from in vitro shoots as follows: Nodes were cultured for 17 hours in a pre-culture solution (PCS), followed by a 20 minute treatment in a loading solution (LS), and a 60 minute incubation in plant vitrification solution 2 (PVS2). The nodes were then flash frozen in liquid nitrogen, re-warmed in an unloading solution at 40°C, and cultured on basal MS culture medium in the dark for 5 days followed by transfer to standard culture conditions. This protocol was tested across 13 genotypes to assess the genotypic variability. The protocol was successful across all 13 genotypes, but significant variation was observed in tissue survival (43.3-80%) and regrowth of shoots (26.7-66.7%). Plants grown from cryopreserved samples were morphologically and chemically similar to control plants for most major traits, but some differences were observed in the minor cannabinoid and terpene profiles. While further improvements are likely possible, this study provides a functional cryopreservation system that works across multiple commercial genotypes for long-term germplasm preservation.

Minerals play many important functions in plant and animal metabolism. Therefore, we investigated the concentration of Se and other minerals and their relationships in soils and fodder plants in Kosovo. Seventy-three samples of each soil and fodder plants (grass, maize, and wheat) from 30 farms were collected. Both soil and plant samples, after processing and digestion, were analyzed for mineral concentration by ICP-MS. Mineral concentrations in soil and fodder crops, and the best predicting/explanatory models for micro minerals concentration, achieved by stepwise linear regression, are presented. Results showed very low concentration of Se in most of the soil and all fodder samples. In addition, the concentration of Co, Zn and Fe was not sufficient to satisfy requirements for all categories of farm animals. Plant Se concentration showed a positive relationship with Se concentration in soils. Plant Zn, Mo, Mn, Fe and Pb, in general, showed no significant relationship with their concentration in soil, while plant Co and Cd showed positive relationship only in maize, and Cu in wheat grain. Among the soil properties, pH had the highest effect on the concentrations of Co, Mo, Mn, Cd and Pb in fodder crops.

Hydrogels are used for various biomedical applications due to their biocompatibility, capacity to mimic the extracellular matrix, and ability to encapsulate and deliver cells and therapeutics. However, traditional hydrogels have a few shortcomings, especially regarding their physical properties, thereby limiting their broad applicability. Recently, researchers have investigated the incorporation of nanoparticles (NPs) into hydrogels to improve and add to the physical and biochemical properties of hydrogels. This brief review focuses on papers that describe the use of nanoparticles to improve more than one property of hydrogels. Such multifunctional hydrogel nanocomposites have enhanced potential for various applications, including tissue engineering, drug delivery, wound healing, bioprinting and biowearable devices.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

Biphasic bone substitutes (BBS) are nowadays established biomaterials. Through their constant development even natural components like hyaluronic acid (HY) are added to improve both their handling and also their regenerative properties. However, low knowledge exists regarding the consequences of the HY addition for their biocompatibility and the inflammatory tissue reactions. Thus, the present study was conducted aiming to analyze the influence of two different amounts of high molecular weight HY (HMWHY) combined with a BBS on the in vitro biocompatibility and the in vivo tissue reaction. Established in vitro procedures using L929 cells were used for cytocompatibility analyses under the test conditions of DIN EN:ISO 10993-5. For the in vivo study part, calvarial defects were created in 20 Wistar rats and subsequently filled with the BBS and the BBS combined with two different HMWHY amounts, i.e., BBS+HY(L) and BBS+HY(H). As controls empty defects were used. Established histological, immunohistochemical and histomorphometrical methods were applied to analyze the tissue reactions to the three different materials, including the induction of pro- and anti-inflammatory macrophages and multinucleated giant cells (BMGCs). The in vitro results showed that none of the materials or compositions caused biological damages to the L929 cells and can considered to be non-toxic. The in vivo results showed that only the addition of high doses of HY to a biphasic bone substitute significantly decreases the occurrence of proinflammatory macrophages (* p < 0.05) comparable to the numbers found in the control group, while no significant differences within the three study groups for M2-macrophages nor BMGCs were detected. In conclusion, the addition of different amounts of HMWHY does not seem to affect the inflammation response to the BBS while improving the material handling properties.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

The three-dimensional printing of scaffolds is an interesting alternative to the traditional techniques of periodontal regeneration. This technique uses computer assisted design and manufacturing after CT scan. After 3D modelling, individualized scaffolds are printed by extrusion, selective laser sintering, stereolithography, or powder bed inkjet printing. These scaffolds can be made of one or several materials such as natural polymers, synthetic polymers, or bioceramics. They can be monophasic or multiphasic and tend to recreate the architectural structure of the periodontal tissue. In order to enhance the bioactivity and have a higher regeneration, the scaffolds can be embedded with stem cells and/or growth factors. This new technique could enhance a complete periodontal regeneration. This review summarizes the application of 3D printed scaffolds in periodontal regeneration. The process, the materials and designs, the key advantages and prospects of 3D bioprinting are highlighted, providing new ideas for tissue regeneration.

Pulse oximetry is the current standard for detecting drops in arterial blood oxygen saturation (SpO₂) associated with obstructive sleep apnea and hypopnea events in polysomnographic (PSG) testing. In cases of hypoxic challenge, such as occurs during apneic events, regulatory mechanisms restrict blood flow to the skin to preferentially maintain SpO₂ for more vital organs. As a result, a measure related to skin tissue oxygenation is likely to be more sensitive to inadequate breathing during sleep than pulse oximetry. Energy Conversion Monitoring (ECM) provides a method for measuring skin tissue oxygen-dependent energy conversion and, as such, is promising for more sensitively detecting sleep disordered breathing (SDB) events compared to pulse oximetry. We hypothesized that ECM would detect hypoxia occurring with SDB events associated with drops in SpO₂ but also would detect hypoxic challenge occurring with SDB events not associated with drops in SpO₂ (hypopneas defined by a drop in nasal pressure occurring in conjunction with an arousal, respiratory-related arousals, and primary snoring). Primary snoring is of particular interest with respect to the potential of ECM because it is statistically associated with co-morbidities of SDB, such as hypertension, but is not considered pathological because of the lack of a proximal measure of pathology occurring with PSG. In this article we review ECM technology and methodology, present preliminary data indicating that it detects hypoxia occurring in the skin during SDB events that is not detected as blood desaturation by pulse oximetry, and make the case that it is a promising tool for identifying pathology occurring at the mild end of the SDB spectrum.

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

Structural and morphological properties of the hydronium-potassium jarosite microstructures were investigated in this work, and their electrical properties were evaluated. All microstructures were synthesized at a reasonable temperature of 343 K with a reduced reaction time of 3 hours. Increase in the pH from 0.8 to 2.1 decreased the particle sized from 3 µm to 200 nm and increasing the aging time from 0, 3 to 7 days resulted in semispherical, spherical and euhedreal jarosite structures, respectively. A Rietveld analysis also was done, finding that increasing pH, the amount of hydronium substitution by potassium in the cationic site also increases, having a 77.72 % of hydronium jarosite (JH) plus 22.29 % potassium jarosite (JK) at pH 0.8; 82.44 % (JH) and 17.56 % (JK) at pH 1.1, and 89.98 % (JH) plus 10.02 % (JK) at pH 2.1. The results obtained in this work show that the obtained hydronium potassium jarosite microstructures with reduced particle size and euhedreal morphology can be used as anode materials for improving the life time of lithium ion batteries, due that during the analysis of the voltage obtained using electrodes made with this particles and graphite, this ranged from 0.89 to 1.36 V.

In our day-to-day life, Lie detection has a significant concern. We human beings are very much inaccurate while detecting the liars and We believe in what we are told. Lie detection is important in today’s life, because Concealing the information or faking it can sometimes take you to huge problems. In any areas like airport management[2], criminal investigations, counterterrorism, etc this concept has great importance. It is an evergreen challenging and changing topic. This paper presents the common technique which was followed up till now and why it was not considered effective and a review of Robust solutions to detection of deception. People generally do not[3] always believe on what someone says but also try to visualize their facial expressions. While in Robust solution these facial micro-expressions are identified, which are tiny, natural expressions seen on the individual’s face, when they try to conceal or suppress emotions. In addition, the article also provides the year-wise assessment and analysis of research articles published in the area of Lie detection from 2011 to 2022. In the end, our proposed framework for lie detection system is also presented. This paper cover up current issues as well as challenges that could be helpful to resolve in future research works. The review paper closes up by supporting future directions.

Adipose tissue (AT) is a remarkably plastic and active organ with functional pleiot-ropism and high remodeling capacity. Although the expansion of fat mass, by defini-tion, represents the hallmark of obesity, the dysregulation of the adipose organ emerges as the forefront of the link between adiposity and its associated metabolic and cardio-vascular complications. The dysfunctional fat displays distinct biological signatures, which include enlarged fat cells (i.e., adipocyte hypertrophy), low-grade inflammation, impaired redox homeostasis, and cellular senescence. While these events are orches-trated in a cell-type, context-dependent and temporal manner, the failure of the adipose precursor cells to form new mature adipocytes appears the main instigator of the adi-pose dysregulation, which, ultimately, poses a deleterious milieu either by promoting ectopic lipid overspill in non-adipose targets (i.e., lipotoxicity) or by inducing an al-tered secretion of different adipose-derived hormones (i.e., adipokines and lipokines). This novel paradigm (“expandability hypothesis”) challenges and extends previous “adipocentric view”, which implies a reduced plasticity of the adipose organ at the nexus between “unhealthy” fat expansion and the development of obesity-associated comorbidities. In this review, we will briefly summarize the potential mechanisms by which adaptive changes to variations of energy balance may impair adipose plasticity and promote fat organ dysfunction. We will also highlight the conundrum with the perturbation of the adipose microenvironment and the development of cardio-metabolic complications by focusing on adipose lipoxidation and cellular senescence. Finally, we discuss the sci-entific rationale for proposing adipose organ plasticity as a target to curb/prevent adi-posity-linked cardio-metabolic complications.

Optical micro-angiography (OMAG) is a new method of detecting flow rate and widely used for in vivo imaging. Although OMAG can distinguish between flowing and stationary parts, it cannot obtain accurate flow rate information. This study proposed a range formula for OMAG and the ultrahigh-sensitivity OMAG (UHS-OMAG) method to quantify the measurement range of an entire system. The parameters of the angle between beam scanning and flow directions, the angular velocity of the galvanometer, and the offset of incident light were introduced, and a formula for calculating the range was derived. Experiments were conducted to measure fine and ultra-fine flow rates by using OMAG and UHS-OMAG methods. The minimum measured flow rate was approximately 30 μm/s, and the maximum measured flow rate was approximately 8 mm/s. Experimental results are in good agreement with the preset results.

Oxidative phosphorylation (OxPhos) is the basic function of mitochondria although the land-scape of mitochondrial functions is continuously growing to include more aspects of cellular homeostasis. Thanks to the application of -omics technologies to the study of the OxPhos system, novel features emerge from the cataloging of novel proteins as mitochondrial thus adding de-tails to the mitochondrial proteome and defining novel metabolic cellular interrelations, espe-cially in the human brain. We focussed on the diversity of bioenergetics demand and different aspects of mitochondrial structure, functions, and dysfunction in the brain. Definition as ‘mitoexome’, ‘mitoproteome’ and ‘mitointeractome’ have entered the field of ‘mitochondrial medicine’. In this context, we reviewed several genetic defects that hamper the last step of aerobic metabolism mostly involving the nervous tissue as one of the most prominent energy-dependent tissues and, as consequence, as a primary target of mitochondrial dysfunction. The dual genetic determination of the OxPhos complexes is one of the reasons for the complexity of the geno-type-phenotype correlation when facing human diseases associated with mitochondria defects; clinically, are characterized by extremely heterogeneous symptoms, ranging from organ-specific to multisystemic dysfunction with different clinical courses. Finally, we briefly discuss the fu-ture directions of the multi-omics study of human brain disorders.

COVID-19 is one of the deadliest respiratory diseases, and its emergence caught the pharmaceutical industry off guard. While vaccines have been rapidly developed, treatment options for infected people remain scarce, and COVID-19 poses a substantial global threat. This study presents a novel workflow to predict robust druggable targets against emerging RNA viruses using metabolic networks and information of the viral structure and its genome sequence. For this purpose, we implemented pymCADRE and PREDICATE to create tissue-specific metabolic models, construct viral biomass functions and predict host-based antiviral targets from more than one genome. We observed that pymCADRE reduces the computational time of flux variability analysis for internal optimizations. We applied these tools to create a new metabolic network of primary bronchial epithelial cells infected with SARS-CoV-2 and identified enzymatic reactions with inhibitory effects. The most promising reported targets were from the purine metabolism, while targeting the pyrimidine and carbohydrate metabolisms seemed to be promising approaches to enhance viral inhibition. Finally, we computationally tested the robustness of our targets in all known variants of concern, verifying our targets’ inhibitory effects. Since laboratory tests are time-consuming and involve complex readouts to track processes, our workflow focuses on metabolic fluxes within infected cells and is applicable for rapid hypothesis-driven identification of potentially exploitable antivirals concerning various viruses and host cell types.

High porosity and mass transport properties of microfiltration polymeric membranes benefits nutrients supply to cells when used as scaffolds in interstitial perfusion bioreactors for tissue engineering. High nutrients transport is assumed when pore size and porosity of the membrane are in the micrometric range. The present work demonstrates that the study of membrane fouling by proteins present in the culture medium, though not done usually, should be included in the routine testing of new polymer membranes for this intended application. Two poly(ε-caprolactone) microfiltration membranes presenting similar average pore size (~0.7µm) and porosity (>80%) but different external surface porosity and pore size have been selected as case study. The present work demonstrates that a membrane with lower surface pore abundance and smaller external pore size (~0.67 µm), combined with adequate hydrodynamics and tangential flow filtration mode is usually more convenient to guarantee high flux of nutrients. On the contrary, having large external pore size (~1.70µm) and surface porosity would incur in important internal protein fouling that could not been prevented with the operation mode and hydrodynamics of the perfusion system. Additionally, the use of glycerol in the drying protocols of the membranes might cause plasticization and a consequent reduction of mass transport properties due to membrane compaction by the pressure exerted to force perfusion. Therefore, preferentially, drying protocols that omit the use of plasticizing agents are recommended.

Background. Specific clinical risk factors that may be associated with ambulatory outcome following thrombolysis therapy in ischemic stroke patients with pre-stroke depression is not fully understood. This was investigated. Methods. Multivariate analyses were performed to identify predictors of functional ambulatory outcomes. Patient demographics and clinical risk factors served as predictive variables, while improvement or no improvement in ambulatory outcome was considered as the primary outcome. Results. A total of 595 of these patients received rtPA of which 310 patients presented with pre-stroke depression, 217 had no improvement in functional outcome, while 93 patients presented with an improvement in functional outcome. Carotid artery stenosis (OR= 11.577, 95% CI, 1.281 – 104.636, P=0.029) and peripheral vascular disease (OR= 18.040, 95% CI, 2.956-110.086, P=0.002) were more likely to be associated with an improvement in ambulation. Antihypertensive medications (OR= 7.810, 95% CI, 1.401 –43.529, P=0.019),previous TIA (OR= 0.444, 95% CI, 0.517 –0.971, P=0.012), and congestive heart failure (OR= 0.217, 95% CI, 0.318 –0.402, P=0.030) were associated with a no improvement in ambulation. Conclusion. After adjustment for covariates, more clinical risk factors were associated with no improvement when compared with improvement in functional outcome following thrombolysis therapy in an acute ischemic stroke population with pre-stroke depression.

Urolithiasis is a painful experience associated with hematuria, damage to kidney tissue and renal failure. It is a multi-factorial disorder while in India, its prevalence is rapidly increasing imposing a large burden for both healthcare and economy globally. In this article, we aimed to evaluate the association between genetic defects in SPP1 gene and urolithiasis from East Indian patients.75 urolithiasis patients were recruited from SSKM Hospital & Institute of Post Graduate Medical Education & Research (IPGME&R), Kolkata, India while 75 healthy controls were recruited from the same community. SNPs based areas of SPP1 gene were analyzed by direct sequencing to identify genetic defects.We identified 3 polymorphisms one synonymous and two 3’UTR variants rs1126616: p.Ala250Ala, rs1126772: 7315 a>g, rs9138: 7471 a>c in SPP1 gene in study individuals. Genotype and allele frequency analysis of these SNPs revealed that, rs9138 SNP was significantly associated with urolithiasis risk in East Indian patients. To our knowledge this is the first study reporting the role of the gene with urolithiasis in the population of West Bengal, India.

The rapid growth of the Information and Communications Technology (ICT) sector requires additional infrastructure, such as more micro-datacenters and telecom stations, to support the higher internet speeds and low latency requirements of 5G net-works. The increased power requirements of the new ICT technologies necessitate the proposal of new power supplies in an attempt to retain the increase in energy demand and running costs. This work provides an in-depth theoretical analysis on the losses of the individual stages of commercially available PSU and proposes a new multicell PSU, Buck-PFC converter, which offers a higher overall efficiency at varying load levels. The theoretical results are verified using simulation results, via PSIM Thermal Module, and using experimental data. The results indicate that multi-cell structures can improve the overall PSU ef-ficiency by 1.2% at 50% rated power and more than 2.1% at full power. Finally, taking into consideration the economic implica-tions of this study, it is shown that the proposed multicell structure may increase the PSU costs by 10.78% but the payback pe-riod is in the order of just 3.3 years.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

Bioglasses are highly adoptable bone substitute materials, which can be combined with so-called therapeutic ions. These ions have shown to influence underlying molecular processes of the bone regeneration cascade. Moreover, it is known that bone substitutes induce an immune reaction within their implantation area involving macrophages and their pro- and anti-inflammatory subtypes dependent on their chemical composition. However, only poor knowledge exists regarding the influence of therapeutic ions onto the immune reactions and the associated bone healing. Thus, the aim of this work was to investigate the influence of strontium- and copper-doped bioglasses on the induction of M1- and M2-macrophages as well as the implant bed vascularization. (2) Methods: For this study, two alkali glasses were produced on basis of ICIE-16 bioglass via the melt-quench route with the addition of 5 wt% copper or strontium (ICIE16-Cu and ICIE16-Sr). Pure ICIE16 and 45S5 bioglasses were used as control materials. The bioactivity (ion release), chemical composition and the surface pattern were investigated, as well as an in vivo experiment was performed using the subcutaneous implantation model in rats. (3) Results: SEM imaging showed different formations of hydroxyapatite on the surfaces of the bioglass systems after submersion in simulated body fluid. EDX analysis confirmed the doping process by showing the release kinetics. Copper-doped bioglass exhibited a higher ion release than strontium-doped bioglass. Copper induced both a low immune cell migration and triggered a low number of M1- and M2-macrophages but also of blood vessels. The strontium-containing bioactive glass induced higher numbers of M1-macrophages after 30 days. Both copper- and strontium-doped bioglasses induced comparable numbers of M2-macrophages as found in the control groups. (4) Conclusions: Bioglass doping with copper and strontium did not exhibit significant influence on the foreign body response or the implantation bed vascularization in vivo. However, the prepared bioglass systems seemed to be biocompatible.

The study of pain requires a balance between subjective methods that rely on self-reports and complementary objective biometrics that ascertain physical signals associated with subjective accounts. There are at present no objective scales that enable the personalized assessment of pain, as most work involving electrophysiology rely on summary statistics from a priori theoretical population assumptions. Along these lines, recent work has provided evidence of differences in pain sensations between participants with Sensory Over Responsivity (SOR) and controls. While these analyses are useful to understand pain across groups, there remains a need to quantify individual differences more precisely in a personalized manner. Here we offer new methods to characterize pain using the moment-by-moment standardized fluctuations in EEG brain activity centrally reflecting the person’s experiencing temperature-based stimulation at the periphery. This type of gross data is often disregarded as noise, yet here we show its utility to characterize the lingering sensation of discomfort raising to the level of pain, individually, for each participant. We show fundamental differences between the SOR group in relation to controls and provide an objective account of pain congruent with the subjective self-reported data. This offers the potential to build a standardized scale useful to profile pain levels in a personalized manner across the general population.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

This paper presents an improved droop control strategy for grid-connected inverter power stability and power quality under distorted with consideration of grid fluctuation and inter-harmonics. An instantaneous frequency without PLL and amplitude of capacitor voltage feed-forward control strategy is given to power stability control, meanwhile a grid current feedback control is given by an incomplete derivation with a high-pass filter, so that the harmonics and inter-harmonics current can be suppressed. These approaches can provide both good active and reactive power dynamic response under fluctuation of frequency, and rejection ability against harmonic and inter-harmonic voltage. Based on model of inverter, the proposed control strategies are designed in detail. Simulations and experiments are present to validate the effectiveness of proposed method.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

Acne vulgaris is a chronic skin disease, which occurs due to inflammation of the hair follicles and sebum producing (sebaceous) glands of the skin called pilosebaceous unit and the anaerobic propionic acne bacterium, P.acne. Human sebum is dominantly made up of 57.5% of triglycerides and fatty acids, 26%wax esters, 12% Squalene and 4.5% Cholesterol. The increased level Androgen hormone, sebum lipid composition, P.acne over growth which induces monocytes and pro inflammatory cytokines attracts neutrophils, basophils, and T cells to the pilosebaceous unit and drive epithelial hyper proliferation i.e., Acne vulgaris. The actual biomolecular changes due to acne vulgaris disease are present in the blood, in the sebum, and in the noninvasive sample of human scalp hair follicles. The main objectives of the present study are to analyze human scalp hair follicles samples using FTIR-ATR spectroscopy to compare and discriminate the spectral signatures of acne vulgaris and healthy scalp hair tissue samples through acne biomarkers Protein, Amide I, Amide II and Squalene (LDL), using the method of internal ratio parameters. This work represents a first step in the development of an analytical tool for future drug development.

Biological micro-dissection has a wide range of applications in the field of molecular pathology. The current laser-assisted dissection technology is expensive, and laser radiation can lead to sample contamination. As an economical and pollution-free micro-dissection method, piezoelectric ultrasonic micro-dissection has a wide application prospect. However, the performance of the current piezoelectric ultrasonic micro-dissection technology is unsatisfactory. In this paper, a novel piezoelectric ultrasonic micro-dissection device based on a flexure mechanism is proposed in order to solve the problems of low dissecting precision and excessive wear of the dissecting needle caused by the harmful lateral vibration of the current piezoelectric ultrasonic micro-dissection device. By analyzing the flexibility of flexure hinge, the type of flexure beam and the optimal design parameters are determined. Through comparing the harmonic response simulation analysis of the micro-dissection device based on a flexure mechanism and the traditional micro-dissection device without the flexure mechanism, the newly designed micro-dissection device achieves the best vibration effect when the driving frequency is 28kHz, compared with the traditional micro-dissection device, the lateral vibration suppression effect is improved by 68%. Then, based on the 3D printing technology, a prototype of a novel micro-dissection device was produced, and its performance was tested. It was found that the flexure mechanism did indeed suppress the lateral vibration of the needle tip. Finally, the experiments of 5μm thick paraffin-embedded rat liver sections were carried out, and the effects of different dissecting parameters on the dissecting effect were analyzed, and the optimal dissecting parameters were obtained. By comparing the dissecting effects of the tissue sample and the wear condition of the needle tip between the novel micro-dissection device and the traditional micro-dissection device under their optimal dissecting parameters, it is proved that the suppression of harmful lateral vibration not only significantly improves the dissecting effect, but also improves the service life and durability of the dissecting needle, which is beneficial to reduce the equipment costs.

Tissue engineering, also called “regenerative medicine”, refers to attempt to create functional human tissue from cells in laboratory. This is a field that uses living cells, biocompatible materials, suitable biochemical and physical factors and their combinations, to create tissue-like structures.. To date, no tissue engineered skeletal muscle implants have been developed for clinical use, but it may represent a valid alternative to treat volumetric muscle loss in the near future. Herein, we reviewed the literature and showed different techniques to produce synthetic tissues with the same architectural, structural and functional properties of native tissues.

Three-dimensional (3D) bioprinting promises to be essential in tissue engineering for solving the rising demand for organs and tissues. Some bioprinters are commercially available, but their impact on the field of TE is still limited due to their cost or difficulty to tune. Herein, we present a low-cost easy-to-build printhead for microextrusion-based bioprinting (MEBB) that can be installed in many desktop 3D printers to transform them into 3D bioprinters. We can extrude bioinks with precise control of print temperature between 2 - 60 ºC. We validated the versatility of the printhead, by assembling it in three low-cost open-source desktop 3D printers. Multiple units of the printhead can also be easily put together in a single printer carriage for building a multi-material 3D bioprinter. Print resolution was evaluated by creating representative calibration models at different temperatures using natural hydrogels such as gelatin and alginate, and synthetic ones like poloxamer. Using one of the three modified low-cost 3D printers, we successfully printed cell-laden lattice constructs with cell viabilities higher than 90% after 24h post printing. Controlling temperature and pressure according to the rheological properties of the bioinks was essential in achieving optimal printability and great cell viability. The cost per unit of our device, which can be used with syringes of different volume, is less expensive than any other commercially available product. These data demonstrate an affordable open-source printhead with the potential to become a reliable alternative to commercial bioprinters for any laboratory.

This review paper delves into using micro-credentials in higher education ecosystems as a digital enablers. Micro-credentials, which are digital credentials that attest to a learner’s mastery of a specific skill or knowledge area, are becoming more popular in higher education. The paper examines the successful implementation of micro-credential frameworks in higher education, using case studies to demonstrate the advantages of micro-credentials. The review emphasizes the agility and flexibility of microcredentials, which enable learners to acquire new skills quickly and respond to changes in the job market. In addition, the paper discusses the digital nature of micro-credentials and how they allow institutionsto provide targeted, skills-based training that isrelevant to employers. It also explores how micro-credentials are delivered through online platforms, making them convenient and easily accessible for learners. The review underscores the significance of digital infrastructure, connectivity, and public utility for promoting micro-credentials. The paper argues that micro-credentials function as a digital enabler for higher edu- cation ecosystems, allowing learners to acquire targeted training and enabling institutions to expand their offerings and reach more students. The paper concludes by highlighting the potential for micro-credentials to help bridge the skills gap and equip learners with the skills necessary to succeed in today’s digital economy.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

Angiogenesis is new blood vessel formation from existing vessels and is a critical first step in tissue repair following chronic disturbances in healing and degenerative tissues. Chronic pathoanatomic tissues are characterized by a high number of inflammatory cells, overexpression of inflammatory mediators, such as tumor necrosis factor-α (TNF-α) and interleukin-1 (IL-1), the presence of mast cells, T cells, reactive oxygen species, and matrix metalloproteinases, and a decreased angiogenic capacity. Multiple studies have demonstrated that autologous orthobiological cellular preparations (e.g., platelet-rich plasma [PRP]) im-prove tissue repair and regenerate tissues. There are many PRP devices on the market. Unfortunately, they differ greatly in platelet numbers, cellular composition, and bioformulation. PRP is a platelet concentrate consisting of a high concentration of platelets with or without certain leukocytes, platelet-derived growth factors (PGFs), cytokines, molecules, and signaling cells. Several PRP products have immunomodulatory capacities that can influence resident cells in a diseased microenvironment, inducing tissue repair or re-generation. Generally, PRP is a blood-derived product, regardless of its platelet number and bioformulation, and the literature indicates both positive and negative patient treatment outcomes. Strangely, the literature does not designate specific PRP preparation qualifications that can potentially contribute to tissue re-pair. Moreover, the literature scarcely addresses the impact of platelets and leukocytes in PRP on (neo)angiogenesis other than a general one-size-fits-all statement that “PRP has angiogenic capabilities.” Here, we review the cellular composition of all PRP constituents, including leukocytes, and describe the importance of platelet dosing and bioformulation strategies in orthobiological applications to initiate angiogenic pathways that re-establish microvasculature networks, facilitating the supply of oxygen and nutrients to impaired tissues.

Magnesium (Mg)-based biomaterials are promising candidates for bone and tissue regeneration. Alloying and surface modifications provide effective strategies for optimizing and tailoring their degradation kinetics. Nethertheless, biocompatibility analyses of Mg-based materials are challenging due to its special degradation mechanism with continous hydrogen release. In this context, the hydrogen release and the related (micro-) milieu conditions pretend to strictly follow in vitro standards based on ISO 10993-5/-12. Thus, special adaptions for the testing of Mg materials are necessary, which have been described in a previous study from our group. Based on these adaptions, further developments of a test procedure allowing rapid and effective in vitro cytocompatibility analyses of Mg-based materials based on ISO 10993-5/-12 are necessary. The following study introduces a new two-step test scheme for rapid and effective testing of Mg. Specimens with different surface characteristcis were produced by means of plasma electrolytic oxidation (PEO) using silicate-based and phosphate-based electrolytes. The test samples were evaluated for corrosion behavior, cytocompatibility and their mechanical and ostogenic properties. Thereby, two PEO ceramics could be identified for further in vivo evaluations.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes, while axial canal is the largest canal amongst the network and distributes at the center of a coral branch. However, previous studies indicated that, in the non-radial symmetry transport system of Acropora, axial canal do not play a major role in the transport of hydroplasm, and the action of axial canal in coral growth is still obscure. In this study, we reconstructed six Acropora muricata samples by high resolution micro-computed tomography to investigate the growth patterns of axial canals during the processes of new branch forming and truncated branch rebuilding. We found that the axial canal of a new branch is transformed from a calice and the polyps in the new branch are budded from the polyp in the axial canal. Meanwhile, the axial canal can transport the calcareous skeletons to rebuild the tip of a truncated branch, which represents as the change in the diameter of axial canal and calcareous deposition/reduction in it. This work indicate the regulation of axial canal in the growth processes including budding, branching, and mineralising of an Acropora colony.

Scaffolds are widely used in tissue engineering because their manufacture is based on natural and synthetic polymers, which allows them to have properties such as biocompatibility and biodegradability, creating an ideal environment for cell growth on their surface. In this context, among the polymers studied in Tissue Engineering are Chitosan (CH) and Polyvinyl Alcohol (PVA). CH is a versatile polymer obtained from de-acetylation of chitin, which is used for its high biodegradability and biocompatibility, although its mechanical properties must be improved. It has been found that one of the ways to improve the mechanical properties of CH is to mix it with other synthetic polymers such as PVA. PVA is known for its biocompatibility, biodegradability, zero toxicity and ease of preparation due to its solubility in water and excellent mechanical properties, such as tensile strength and ease in the formation of films and barriers. In this study we evaluated the capacity of scaffolds made with CH and PVA in different concentrations (2: 1, 1: 1, 1: 2, respectively) as a possible application in bone regeneration. This was made through different characterization tests such as Infrared Spectroscopy, AFM, Swelling test and Porosity test, where we obtained information about its structural and physicochemical properties. Additionally, a cellular quality control was performed on the material through the MTT assay. The Fourier transform infrared spectroscopy (FTIR) study showed that there are strong intermolecular hydrogen bonds between the chitosan and polyvinyl alcohol molecules. The Swelling and Porosity tests showed favorable results, obtaining maximum values ​​of 5519% and 72.17% respectively. MTT tests determined that the prepared materials are not cytotoxic. These findings suggest that scaffolds possess properties suitable for use in Tissue Engineering.

Novel advanced biomaterials have recently gained great attention, especially in surgical minimally invasive techniques. Applying sophisticated design and engineering methods, various elastomer-hydrogel systems (EHS) with outstanding performance have been developed in last decades. Those systems composed of elastomers and hydrogels are very attractive due to their high biocompatibility, injectability, controlled porosity and often antimicrobial properties. Moreover, elastomeric properties and bioadhesiveness are making them suitable for soft tissue engineering. Herein, we present the advances in current state-of-the-art design principles and strategies for strong interface formation inspired by nature (bio-inspiration), diverse properties and applications of elastomer-hydrogel systems in different medical fields, in particular, in tissue engineering. Functionalities of those systems, including adhesive properties, injectability, antimicrobial properties and degradability applicable to tissue engineering will be discussed in a context of future efforts towards development of advanced biomaterials.

G protein-coupled receptors (GPCRs) are expressed essentially on all cells, facilitating cellular responses to external stimuli, and are involved in nearly every biological process. Several members of this family play significant roles in the regulation of adipogenesis and adipose me-tabolism. However, the expression and functional significance of a vast number of GPCRs in adipose tissue are unknown. We used a high-throughput RT-PCR panel to determine the expres-sion of the entire repertoire of non-sensory GPCRs in mouse white, and brown adipose tissue and assess changes in their expression during adipogenic differentiation of murine adipocyte cell line, 3T3-L1. In addition, the expression of GPCRs in subcutaneous adipose tissues from lean, obese, and diabetic human subjects was evaluated by re-analyzing RNA-sequencing data. We detected a total of 292 and 271 GPCRs in mouse white and brown adipose tissue, respectively. There is a significant overlap in the expression of GPCRs between the two adipose tissue depots but several GPCRs are specifically expressed in one of the two tissue types. Adipogenic differ-entiation of 3T3-L1 cells had a profound impact on the expression of several GPCRs. RNA se-quencing of subcutaneous adipose from healthy human subjects detected 255 GPCRs and obesity significantly changed the expression of several GPCRs in adipose tissue. Finally, we report sev-eral highly expressed GPCRs with no known role in adipose biology whose expression was sig-nificantly altered during adipogenic differentiation and/or in the diseased human subjects. These GPCRs could play an important role in adipose metabolism and serve as a valuable translational resource for obesity and metabolic research.

This study aimed to investigate Coll-I, III, IV and elastin in canine normal prostate and PC, using Picrosirius red (PSR) and Immunohistochemical (IHC) analysis. Eight normal prostates and 10 PC from formalin-fixed, paraffin-embedded samples were used. Collagen fibers area was analyzed with ImageJ software. The distribution of Coll-I and Coll-III was approximately 80% around prostatic ducts and acini, 15% among smooth muscle and 5% surrounding blood vessels, in both normal prostate and PC. There was a higher median area of Coll-III in PC, when compared to normal prostatic tissue (p=0.001 for PSR and p= 0.05 for IHC). Immunostaining for Coll-IV was observed in the basal membrane of prostate acini, smooth muscle, blood vessels, and nerve fibers of normal and PC samples. Although there was no difference in Coll-IV area between normal tissue and PC, tumors with Gleason score 10 showed absence of Coll-IV, when compared to scores 6 and 8 (p=0.0095). Elastic fibers were found in the septa dividing the lobules and around the prostatic acini of normal samples, and was statistically higher in PC, compared to normal tissue (p=0.00229). Investigation of ECM components brings new information and should be correlated with prognosis in future studies.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

Micro-plastics (MPs) become significantly important to society since their commercial manufacture began in the 1950s because of their low production costs, stability, light weight, and adaptability. Plastic was produced in 400 million tons worldwide in 2020, compared to 1.5 million tons just 60 years earlier. Scientists predict that by 2050, plastic production would increase to 33 billion tons. MPs are a rising scientific and societal issue in the environment as a new type of contaminant that is widely disseminated in aquatic ecosystems and organisms. Aquatic species that come into contact with MPs for an extended period of time experience ecotoxicity, which includes oxidative stress, genotoxicity, neurotoxicity, and reproductive issues. In aquatic environments, MPs not only transport chemicals within animals but also serve as mediators for chemicals or other contaminants. As a result of co-exposure of MPs and chemical contaminants, various toxicity incidences involving aquatic organisms have been reported. The final exposure of MPs occurs in humans through biomagnification of aquatic edible products. This study presents an important overview of the literature on MP ingestion by aquatic biota. It covers topics such as the present scenario of plastic pollution worldwide, the pathways that MPs take to reach humans and aquatic species, the eco-toxicological impacts of MPs on aquatic species, the relation between MPs and other environmental pollution and the ensuing effects on aquatic organisms, and the MP pollution status in Bangladesh.

Background: The course of obesity and type 2 diabetes (T2D) development is highly dependent on adipose tissue (AT) angiogenesis. Moreover, angiogenic microRNAs (miRNAs) play pivotal role in AT functionality. The aim of this study was to analyze the relationship of the human AT miR-221-3p/222-3p cluster and their regulatory network with obesity and T2D. Methods: miR-221-3p/222-3p and their target genes (TG) expression levels were measured in visceral and subcutaneous ATs from patients classified according to their BMI and to their glycemic status with a high degree of insulin resistance (IR) and T2D. In silico analyses of miR-221-3p/222-3p and their TGs were performed to identify relevant signaling pathways. Results: A multivariate analysis, including the simultaneous expression of miR-221-3p and miR-222-3p as dependent variables, showed significant differences considering the variables; tissue depot, obesity, IR and T2D altogether as independent variables. In addition, miRNAs and their TGs were differentially expressed according to obesity degree, glycemic status, and AT depot type. Our in silico analysis showed that miR-221-3p/222-3p cluster TGs are mostly involved in angiogenesis, WNT signaling pathway and apoptosis. Conclusion: These findings suggest that the miR-221-3p/222-3p cluster and their related regulatory networks could represent tangible targets for the management of obesity and associated metabolic disorders

Purpose: to assess the effect of photobiomodulation (PBM) on human gingival fibroblast proliferation. Methods: The study was conducted using the primary cell cultures of human fibroblasts collected from systemically healthy donors. Three different laser types: Nd:YAG (1064nm), infrared diode laser (980nm) and prototype led laser emitting 405, 450 and 635nm were used to irradiate fibroblasts. Thanks to the patented structure of that laser, it was possible to irradiate fibroblasts with a beam combining two or three wavelengths. The energy density was 3 J/cm², 25 J/cm², 64 J/cm². The viability and proliferation of cells were determined using the MTT test conducted 24, 48 and 72 hours after laser irradiation. Results: The highest percentage of mitochondrial activity (MA=122.1%) was observed in the group irradiated with the 635nm laser, with an energy density of 64 J/cm² after 48 hours. The lowest percentage of MA (94.0%) was observed in the group simultaneously irradiated with three wavelengths (405 + 450 + 635 nm). The use of the 405nm laser at 25 J/cm² gave similar results to the 635 nm laser. Conclusions: The application of the 635nm and 405nm irradiation caused a statistically significant increase in the proliferation of gingival fibroblasts.

Substantial research is required to ensure that micro-mobility ride sharing provides a better fulfillment of user needs. This study proposes a novel crowdsourcing model for the ride-sharing system where light vehicles such as scooters and bikes are crowdsourced. The proposed model consists of three entities: suppliers, customers, and a management party responsible for receiving, renting, booking, and demand matching with offered resources. It can allow suppliers to define the location of their private e-scooters/e-bikes and the period of time they are available for rent. Using a dataset of over 9 million e-scooter trips in Austin, Texas, we ran an agent-based simulation six times using three maximum battery ranges (i.e., 35, 45, and 60 km) and different numbers of e-scooters (e.g., 50 and 100) at each origin. Computational results show that the proposed model is promising and might be advantageous to shift the charging and maintenance efforts to a crowd of suppliers.

This paper proposes a novel micro-grid structure, which can operate fully-autonomously with inherent seamless switching. It can operate independently in both grid-connected and islanded mode as a self-governed entity without relying on the utility grid. An AC/DC/AC converter is employed as the interface between the micro-grid and the utility grid, which enables the two entities to have different voltages in grid-connected mode. Seamless switching between operation modes can be achieved naturally. The micro-grid is regulated to exchange predefined amount of power with the utility grid in grid-connected mode. This will benefit the power dispatching algorithm of the power system. The predefined power is estimated based on power forecasting of local renewable generations and loads with consideration of the Sate of Charge (SOC) of the battery, and is updated and broadcasted every certain period. A small scale AC micro-grid with a rotating generator, battery storage and solar arrays etc. is built for investigation. Matlab/Simulink results are provided to validate the robustness and flexibility of proposed micro-grid and its operation strategy.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

Beta cells couple stimulation by glucose with insulin secretion and impairments in this coupling play a central role in diabetes mellitus. To clarify the effect of cAMP and the role of Epac2A in intracellular calcium signals and intercellular coupling, we performed functional multicellular calcium imaging in beta cells in mouse pancreas tissue slices after stimulation with glucose and forskolin in wild-type and Epac2A knock-out mice. Increased cAMP evoked calcium signals in otherwise sub-stimulatory glucose and beta cells from Epac2A knock-out mice displayed a faster activation. During the plateau phase, beta cells from Epac2A knock-out mice displayed a slightly higher active time in response to glucose compared with wild-type littermates, and increased cAMP increased the active time via a large increase in oscillation frequency and small decrease in oscillation duration in both Epac2A knock-out and wild-type mice. Functional network properties during stimulation with glucose did not differ in Epac2A knock-out mice, but the presence of Epac2A was crucial for the protective effect of increased cAMP in preventing a decline in beta cell functional connectivity with time. Finally, increased cAMP prolonged beta cell activity during deactivation in an Epac2A-independent manner.

Balínt Syndrome is an acquired disorder manifesting in the inability to recognize several objects at once (simultagnosia), inaccurate visually guided limb movements despite intact motor function (optic ataxia) and the inability to make accurate voluntary saccades to visual targets despite demonstrating unrestricted range of eye movements (ocular motor apraxia). Here we report the first case of a patient presenting with Balínt Syndrome caused by a platelet-derived growth factor receptor A mutation (PDGFRA)-induced Hypereosinophilic Syndrome (HES).

Cholinergic innervation in pancreas controls both the release of digestive enzymes to support the intestinal digestion and absorption, as well as insulin release to promote nutrient use in the cells of the body. The effects of muscarinic receptor stimulation are described in detail for endocrine beta cells and exocrine acinar cells separately. Here we describe morphological and functional criteria to separate these two cell types in situ in tissue slices and simultaneously measure their response to ACh stimulation on cytosolic Ca2+ oscillations [Ca2+]c in stimulatory glucose conditions. Our results show that both cell types respond to glucose directly in the concentration range compatible with the glucose transporters they express. The physiological ACh concentration increases the frequency of glucose stimulated [Ca2+]c oscillations in both cell types and synchronizes [Ca2+]c oscillations in acinar cells. The pharmacological ACh concentration further increases the oscillation frequency on the level of individual beta cells, inhibits the synchronization between these cells, and abolishes oscillatory activity in acinar cells. We discuss possible mechanisms leading to the observed phenomena.

The repurposing of licenced drugs for use against COVID-19 is one of the most rapid ways to develop new and alternative therapeutic options to manage the ongoing pandemic. Given the approximately 8,000 licenced compounds available from Compounds Australia that can be screened, this paper demonstrates the utility of commercially-available ex vivo/3D airway and alveolar tissue models. These models are a closer representation of in vivo studies compared to in vitro models, but retain the benefits of rapid in vitro screening for drug efficacy. We demonstrate that several existing drugs appear to show anti-SARS-CoV-2 activity against both Delta and Omicron Variants of Concern in the airway model. In particular, fluvoxamine, as well as aprepitant, everolimus, and sirolimus have virus reduction efficacy comparable to the current standard of care (remdesivir, molnupiravir, nirmatrelvir). Whilst these results are encouraging, further testing and efficacy studies are required before clinical use can be considered.

Adiposity is associated with adverse health conditions such as obesity, cardiovascular disease and type 2 diabetes. The combination of resistance exercise and creatine supplementation has been shown to decrease body fat % in adults ≥ 50 years of age. However, the effects in adults < 50 years of age is unknown. To address this limitation, we systematically reviewed the literature and performed several meta-analyses comparing studies that included resistance exercise and creatine supplementation to resistance exercise and placebo. Twelve studies were included involving 266 participants. Adults (< 50 years of age) that supplemented with creatine and performed resistance exercise experienced a significant reduction in body fat % (-1.19%, p=0.006) and a non-significant reduction in absolute fat mass (-0.09 kg, p=0.88). Collectively, the combination of resistance exercise and creatine supplementation produces a very small reduction in body fat % in adults < 50 years of age.

Epigenetic changes are a hallmark of short- and long-term transcriptional regulation, and hence instrumental in the control of cellular identity and plasticity. Epigenetic mechanisms leading to changes in chromatin structure, accessibility for recruitment of transcriptional complexes, and interaction of enhancers and promoters all contribute to acute and chronic adaptations of cells, tissues and organs to internal and external perturbations. Similarly, the peroxisome proliferator-activated receptor γ coactivator 1α (PGC-1α) is activated by stimuli that alter the cellular energetic demand, and subsequently controls complex transcriptional networks responsible for cellular plasticity. It thus is of no surprise that PGC-1α is under the control of epigenetic mechanisms, and constitutes a mediator of epigenetic changes in various tissues and contexts. In this review, we summarize the current knowledge of the link between epigenetics and PGC-1α in health and disease.

Low pressure fluid transport (1) applications often require low and precise volumetric flow rates (2) including low leakage to reduce additional costly and complex sensors. A peristaltic pump de-sign (3) was realized, with the fluid’s flexible transport channel formed by a solid cavity and the wobbling plate comprising a rigid and a soft layer (4). In operation, the wobbling plate is driven externally by an electric motor, hence, the soft layer is contracted and unloaded (5) during pump-cycles transporting fluid from low to high pressure sides. A thorough characterization of the pump system is required to design and dimension the components of the peristaltic pump. To capture all these parameters and their dependencies on various operation-states, often complex and long-lasting dynamic 3D FE-simulations are required. We present, here, a holistic design methodology (6) including analytical as well as numerical calculations, and experimental valida-tions for a peristaltic pump with certain specifications of flow-rate range, maximum pressures, and temperatures. An experimental material selection process is established and material data of candidate materials (7) (liquid silicone rubber, acrylonitrile rubber, thermoplastic-elastomer) are directly applied to predict the required drive torque. For the prediction, a semi-physical, analyti-cal model was derived and validated by characterizing the pump prototype.

Posterior capsule opacification (PCO) is the most common complication of cataract surgery. It causes a gradual deterioration of visual acuity, which would otherwise remain improved after a successful procedure. Despite recent advances in ophthalmology, this complication has not been eradicated and the incidence of PCO can be as high as 10%. This article reviews the literature concerning the pathomechanism of PCO and examines the biochemical pathways involved in its formation and methods to prevent this complication. We also review the reported tests performed in cell cultures under laboratory conditions, in experimental animal models, and in ex vivo human lens capsules. Finally, we describe research involving human eyes in the clinical setting and pharmacological methods that may reduce the frequency of PCO. Due to the multifactorial eti-ology of PCO, in vitro studies make it possible to assess the factors contributing to its complica-tions and search for new therapeutic targets. Not all pathways involved in cell proliferation, mi-gration, and contraction of the lens capsule are reproducible in laboratory conditions; moreover, PCO in humans and laboratory animals may be additionally stimulated by various degrees of postoperative reactions depending on the course of surgery. Therefore, further studies are necessary.

The concerning worldwide increase of obesity and chronic metabolic diseases such as T2D, dyslipidemia, and cardiovascular disease motivates further investigations into preventive and alternative therapeutic approaches. Over the past decade, there is growing evidence that the formation and activation of thermogenic adipocytes (brown and beige) may serve as therapy to treat obesity and its associated diseases owing to its capacity to increase energy expenditure and to modulate circulating lipids and glucose levels. Thus, understanding the molecular mechanism of brown and beige adipocytes formation and activation will facilitate the development of strategies to combat metabolic disorders. Here, we provide a comprehensive overview of pathways and players involved in the development of brown and beige fat as well as the role of thermogenic adipocytes in energy homeostasis and metabolism. Also, we discuss the alterations in brown and beige adipose tissue function during obesity and, explore the therapeutic potential of thermogenic activation to treat metabolic syndrome.

Formalism proofing general derivation, applying matrix properties operations, showing fundamental relationships with inner product to outer product has been advanced here. This general proof formalism has direct application with physics to quantify quantum density at micro scale level to time commutator at macro scale level. System of operator algebraic equations have been rigorously derived to obtain analytic solutions which are physically acceptable. Extended physics application will include metricizing towards unitarization to achieve gaging Hamiltonian mechanics to electromagnetic gravitational strong theory, towards grand unifying physics atomistic to astrophysics or vice versa via quantum relativistic general physics thereby patching to classical physics fields energy.

Glaucoma is a blinding disease largely caused by increased resistance to drainage of fluid from the eye’s anterior chamber, resulting in elevated intraocular pressure (IOP). A major site of fluid outflow regulation and pathology is the trabecular meshwork (TM) at the entrance of the eye’s drainage system. We aimed to characterize the structural and functional properties of a newly developed tissue-engineered anterior segment eye culture model. We hypothesized that repopulation of a decellularized TM with non-native TM cells could restore aspects of normal TM. The decellularization protocol removed all cells and debris while preserving the ECM. Seeded cells localized to the TM region and progressively infiltrated the meshwork ECM. Cells reached a distribution comparable to control TM after four days of perfusion culture. After a perfusion rate increase challenge, tissue-engineered cultures reestablished normal IOPs (reseeded = 13.7±0.4 mmHg, decellularized = 35.2±2.2 mmHg, p < 0.0001). eGFP expressing CrFK control cells caused a high and unstable IOP (27.0±6.2 mmHg). In conclusion, we describe a readily available, storable, and biocompatible scaffold for anterior segment perfusion culture of non-native cells. Tissue-engineered organs demonstrated similarities to native tissues and may reduce the need for scarce donor globes in outflow research.

Optical biopsy describes a range of medical procedures in which light is used to investigate disease in the body, often in hard-to-reach regions via optical fibres. Optical biopsies can reveal a multitude of diagnostic information to aid therapeutic diagnosis and treatment with higher specificity and shorter delay than traditional surgical techniques. One specific type of optical biopsy relies on Raman spectroscopy to differentiate tissue types at the molecular level and has been used successfully to stage cancer. However, complex micro-optical systems are usually needed at the distal-end to optimise the signal-to-noise properties of the Raman signal collected. Manufacturing these devices remains a critical challenge, particularly in a way suitable for large scale adoption. In this paper, we describe a novel fibre-fed micro-optic system designed for efficient signal delivery and collection during a Raman spectroscopy based optical biopsy. Crucially, we fabricate the device using a direct-laser-writing technique known as ultrafast laser assisted etching which is scalable and allows components to be aligned passively. The Raman probe has a sub-millimetre diameter and offers confocal signal collection with 71.3 ± 1.5% collection efficiency over a 0.8 numerical aperture. Proof of concept spectral measurements were performed on mouse intestinal tissue and compared with results obtained using a commercial Raman microscope.

During March and April 2020, the European Union (EU) was the center of the COVID-19 pandemic. Many National Governments imposed severe lockdown policies to mitigate the health crisis. The European Parliament commissioned a survey to analyse the citizens’ attitudes over a number of issues related to the COVID-19 pandemic. 21804 European citizens in 21 EU countries responded the survey between 23 April and 1 May 2020. The paper analyses empirically the individual satisfaction that European citizens have experienced over the measures taken by the respective National Governments to control the COVID-19 pandemic. The analysis is based on a micro-econometric model (ordered probit) that explains the citizens’ satisfaction by a number of attitudes and sociodemographic factors. Our results reveal that Spaniards are the least satisfied citizens in comparison with Danes, Irelanders, Greeks and Croats who are the most satisfied nationals. The years of education and the social class also play a determinant role. We also find that the most important determinant is the political support to the Government, and that those who are more worried by the economy and the protection of individual rights are usually more critic with the measures than those who are more worried by the health consequences.

The optimization problem of two or more special-purpose functions of the energy system is subjected to an analysis. Based on experience of our research and general knowledge of partial solutions of energy system optimization at the level of control of production and power energy supply by energy companies in the Czech Republic, a special-purpose (cost) function has been defined. By analysing the special-purpose function, penalty and limitations have been defined. Using the fuzzy logic, a set of suitable solutions for the special-purpose function is accepted. An optimum of the special-purpose function is looked for using the simulated annealing method. The history of electricity consumption is sorted by day and by hour, representing the multidimensional data. When using the cluster analysis, type daytime diagrams of consumption are defined. Type daytime diagrams form prototypes of identified clusters. The so-called self-organizing neural network with Kohonen map attached is used to perform the cluster analysis. The result of our research is presented by an experiment.

The integration of Wireless Sensor Networks (WSNs) into agricultural areas has had a significant impact and has provided new, more complex, efficient, and structured solutions for enhancing crop production. This research reviews the role of Wireless Sensor Networks (WSNs) in monitoring the macro-nutrient content of plants. The review study focuses on identifying the types of sensors used to measure macro-nutrients, determining sensor placement within agricultural areas, implementing wireless technology for sensor communication, and selecting device transmission intervals and ratings. The study of NPK (Nitrogen, Phosphorus, Potassium) monitoring using sensor technology in precision agriculture is of high significance in efforts to improve agricultural productivity and efficiency. In addition to fostering technological innovations and precision farming solutions, in future this research aims to increase agricultural yields, particularly by enabling the cultivation of certain crops in locations different from their original ones.