As a consequence of the increasing share of renewable energies and sector coupling technologies, new approaches are needed for the study, planning, and control of modern energy systems. Such new structures may add extra stress to the electric grid, as is the case with heat pumps and electrical vehicles. Therefore, the optimal performance of the system must be estimated considering the constraints imposed by the different sectors. In this research, a dispatch optimization method with an iterative grid constraint generation, decoupled from the linear unit commitment problem, is employed. From the considered scenarios, it was found that in a typical German neighborhood with 150 households, PV penetration of ∼5kWp per household can lead to curtailment of ∼60MWh per year due to line loading. Furthermore, the proposed method eliminates grid violations due to the addition of new sectors reducing the curtailment up to 60%. With the optimization of the heat pump operation, an increase of 7% of the self-consumption was achieved with similar results for the combination of battery systems and electrical vehicles. In conclusion, a safer and optimal operation of a complex energy system is fulfilled. Safer control strategies and more accurate plant sizing could be derived from this work.

Laser reduced graphene oxide (LRGO) on a PET substrate was prepared in one-step to obtain the LRGO grid electrode for sensitive carbaryl determination. The grid form results in a grid distribution of different electrochemically active zones affecting the electroactive substance diffusion towards to the electrode surface and increasing the electrochemical sensitivity for carbaryl determination. Carbaryl is electrochemically irreversibly oxidized by the secondary amine moiety of the molecule with the loss of one proton and one electron in the pH range from 5 to 7 by LSV on the LRGO grid electrode with a scan rate of 300 mV/s. Some interference of the juice matrix molecules did not significantly affect the LSV oxidation current of carbaryl on the LRGO grid electrode after adsorptive accumulation without applied potential. The LRGO grid electrode can be used for LSV determination of carbaryl in fruit juices in the concentration range from 0.25 to 128 mg/L with LOD of 0.1 mg/L by. The fabrication of the LRGO grid electrode opens up possibilities for further inexpensive monitoring of carbaryl in other fruit juices and fruits.

An indisputable fact about our planet is that its atmospheric temperature has risen dramatically during the past century. Combustion of fossil fuels and their subsequent greenhouse gas emissions are thought to be the main contributors to recent changes within the Earth’s ecosystem. The transportation sector and electricity generating power plants are each responsible for approximately one-third of these emissions. Shifting towards a cleaner and renewable resources to generate electricity is believed to omit a big portion of polluting substances. Improvements in vehicles’ fuel efficiency and the introduction of alternative fuels besides strategic plans to control travel demand are among the most promising approaches to alleviate emissions from the transportation sector. Recent technology advancements, however, drew much attention to the production and manufacturing of alternative fuel vehicles, electric vehicles in particular. Since these vehicles use electricity as part of or all their powertrain, assessing the amount of emissions they produce is closely tied to the cleanliness of the electricity source. In order for a valid comparison to be made between internal combustion and electric vehicles, hence, a life cycle assessment procedure needs to be followed from production stages to terminal life of vehicles. Involvement of numerous affecting factors during the lifetime of a vehicle on one hand, and the ambiguity in the exact source of electricity used to charge electric vehicles on the other hand bring about more complexities. The latter case is more commonly known as the marginal grid problem, which deals with how a combination of sources used to generate electricity can influence the life cycle emissions. There are also other concerns regarding the growth in fuel-efficient and electric vehicles. Transportation planners argue that new developments in the vehicle industry may attract more people to owning and driving cars. This phenomenon which is better known as a rebound effect not only will result in increased traffic congestion, but it can also outpace the environmental benefits from utilizing electric vehicles. Moreover, since fuel taxes comprise the majority of Highway Trust Funds, alternative ways to compensate for state and federal revenues should be devised. This paper is an attempt to review the existing literature to better elaborate on the role of the transportation sector in controlling climate change threats. More specifically, issues around the use of electric vehicles and how they can contribute to more environmentally friendly communities are discussed.

A cognitive radio sensor network (CRSN) based Smart Grid (SG) is a new paradigm for a modern SG. It is totally different from the traditional power grid and also different from the conventional SG that uses a static resource allocation technique to allocate resources to sensor nodes and communication devices in the SG network. Due to the challenges associated with competitive sensor nodes and communication devices in accessing and utilizing radio resources, the need for dynamic radio resource allocation (RRA) has been proposed as a solution for allocating radio resources to sensor nodes in a CRSN based smart grid ecosystem (network). These challenges include energy/power constraints, poor quality of service (QoS), interference, delay, spectrum efficiency issues, and excessive spectrum hand-offs. Hence, the optimization of resource allocation criteria, such as energy efficiency, throughput maximization, QoS guarantee, fairness, priority, interference mitigation/avoidance, etc., will go a long way in addressing the problems of RRA in a CRSN based SG. Consequently, this work explores RRA in CRSNs for SGs. Various resource allocation schemes, as well as its architecture in a CRSN for SG environment, are presented. The work reported in this paper introduces a model called the “guaranteed network connectivity channel allocation” for throughput maximization (GNC-TM) and optimal spectrum band determination in RRA for improved throughput criteria in CRSNs for SGs. The results show that the model outperforms the existing protocol in terms of throughput and error probability. Finally, the contribution to knowledge and future research direction, such as energy efficiency and hybrid energy harvesting schemes are highlighted.

Energy storage systems will play a key role for individual users in the future smart grid. They serve two purposes: (i) handling the intermittent nature of renewable energy resources for a more reliable and efficient system, and (ii) preventing the impact of blackouts on users and allowing for more independence from the grid, while saving money through load-shifting. In this paper we investigate the latter scenario by looking at a neighbourhood of 25 households whose demand is satisfied by one utility company. Assuming the users possess lithium-ion batteries, we answer the question of how each household can make the best use of their individual storage system given a real-time pricing policy. To this end, each user is modelled as a player of a non-cooperative scheduling game. The novelty of the game lies in the advanced battery model, which incorporates charging and discharging characteristics of lithium-ion batteries. The action set for each player comprises day-ahead schedules of their respective battery usage. We analyse different user behavior and are able to obtain a realistic and applicable understanding of the potential of these systems. As a result, we show the correlation between the efficiency of the battery and the outcome of the game.

The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

The severe and complex COVID-19 symptoms, often needing hospital care, occur suddenly, late in the virus replication stage of SARS-CoV-2 infection. Hospitalised patients have tissue damage due to micro-clots at multiple sites. Could long-covid, also clinically variable, be a milder form caused by “nano-clots”, too small to cause detectable tissue damage? The timing and suddenness of the onset of serious disease needs an explanation. A paper reported on the first 20 children needing urgent hospital care. No child had any symptoms prior to suddenly becoming seriously ill, only one had a positive PCR test but all had positive SARS-CoV-2 antibody test. That finding indicated to me that this onset occurred at the moment of sero-conversion. An emerging viral moiety, the virion-IgG-antibody complex, has concentrations rapidly increasing, then decreasing. It is known that influenza-IgG-antibody-complex consists of many virions bound together by the antibody. It seems a reasonable step to propose that SARS-2, being a large virus and having many spike proteins, can form larger clumps of virus-IgG-antibody complexes than with influenza, the former being sufficiently large to initiate micro-clots. Therefore, my hypotheses is that the SARS-CoV-2 virion-antibody complex initiates micro-clot formation. Either before or after sero-conversion, the complex will be at too low a concentration to initiate micro-clots. To be useful, a hypothesis should be testable, provide explanations and give predictions. My presentation will give examples. I like the way that several apparently separate pieces of a jig-saw puzzle have come together to form a single picture. [I suggest that the reader scrolls down to the addenda [10,11 & 12] before reading the ICAR Poster]

The spatial segregation is a characteristic of Latin American cities, resulting in distinct dynamics of social inclusion and exclusion at both spatial and identity levels. Then, specific green spaces may convert into appreciated and contested territories, where various actors negotiate their uses and regulations. Considering a case-study in a green icon of the metropolitan city of Santiago de Chile, the main objective of the present study was to describe and comprehend the uses and meanings of the Quebrada Macul park among different social groups over the past two decades. We employed qualitative methods including six in-depth interviews with key informants (social and ecological leaders, historical neighbors, and park workers), five participant observations in the park, and statistical analysis of visitors. Results reveal that (1) the transition of being a popularly used hill to a metropolitan park rises tensions between public and private statuses of place; (2) conflicts emerge regarding who uses the space and how, reflecting power dynamics among different social groups; (3) the park, beyond being a public space, holds significant identity value for its historical residents, both for those who fought for its recovery and those who have lived closely, so processes of forgetfulness might be resentful. We conclude on enduring meanings of the park associated with the struggle for the place among different groups, highlighting the role of memory for the social integration of groups among natural spaces.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

Micro-plastics (MPs) become significantly important to society since their commercial manufacture began in the 1950s because of their low production costs, stability, light weight, and adaptability. Plastic was produced in 400 million tons worldwide in 2020, compared to 1.5 million tons just 60 years earlier. Scientists predict that by 2050, plastic production would increase to 33 billion tons. MPs are a rising scientific and societal issue in the environment as a new type of contaminant that is widely disseminated in aquatic ecosystems and organisms. Aquatic species that come into contact with MPs for an extended period of time experience ecotoxicity, which includes oxidative stress, genotoxicity, neurotoxicity, and reproductive issues. In aquatic environments, MPs not only transport chemicals within animals but also serve as mediators for chemicals or other contaminants. As a result of co-exposure of MPs and chemical contaminants, various toxicity incidences involving aquatic organisms have been reported. The final exposure of MPs occurs in humans through biomagnification of aquatic edible products. This study presents an important overview of the literature on MP ingestion by aquatic biota. It covers topics such as the present scenario of plastic pollution worldwide, the pathways that MPs take to reach humans and aquatic species, the eco-toxicological impacts of MPs on aquatic species, the relation between MPs and other environmental pollution and the ensuing effects on aquatic organisms, and the MP pollution status in Bangladesh.

Castanea sativa Mill., an indigenous species of the mountainous Gabala region of Azerbaijan, where its local variety is now facing the danger of extinction. The preservation of this variety of European chestnut requires the development of effective strategies for reliable in vitro regeneration systems as an alternative to traditional methods, which has become the main objective of this study. In solving this problem, the generally accepted technique of micro-multiplication of axillary shoots was mainly used. First, a phased sterilization of was carried out using liquid soap, Previkur fungicide and mercury (II) chloride. DKW (Driver and Kuniyuki Walnut) nutrient medium was used for germination of explants, into which growth stimulants BAP (Benzilamunapurine), IBA (Indole - 3 butyric acid), IAA (Indole Acetic acid), NAA (Naphthalene Acetic Acid) and GA3 (Gibberelic acid) were introduced in various combinations and quantities. The test of the above-mentioned sterilization model revealed significant shortcomings in terms of the acceptability of the results obtained (16-77%). It was also found that the germination of explants takes 14 days and it is better to conduct it in a DKW environment containing hormones BAP (0.6 mg), IBA (0.1 mg) and GA3 (0.1 mg) / 1 L DKW. A mixture of BAP (0.1mg) + IBA (0.35 mg) is more suitable for the reproduction of grown explants + GA3 (0.2 mg) / 1 l DKW (the result is 3 new micro-plants for each explant), and for good root formation (it takes 30 days) – a mixture of IBA 1.0 mg + NAA 0.5 mg + IAA 0.5 mg / l L DKW. After the shoots have acquired a certain length (at least 1.5 cm), it is required to transfer them for 22 days to a DKW medium containing IBA (1 mg), IAA (0.5 mg) and NAA(0.5 mg) / l L DKW so that the root splitting process begins and ends.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Artificial intelligence, a key technological tool in the era of the 4th Industrial Revolution, is being actively applied to education beyond industry, economy, and culture. In the future society, understanding and using artificial intelligence technology will be considered an essential skill for everyone, and the professionalism of AI education for pre-service teachers nurturing future talents is also important. This study verifies the effectiveness of pre-service teachers after undergoing a 15-week extension program consisting of AI Literacy Education (10 weeks), AI-Linked Subjet Education (3 weeks), and Micro-teaching (2 weeks) which was designed to enhance the AI ​​education professionalism of pre-service teachers. The AI Literacy Education section consisted of understanding AI, AI ethics, and basic programming, and the education was conducted through both experience and practice. After that, the pre-service teachers analyzed the curriculum of the 5th and 6th grades of an elementary school, and developed a subject-related education program using AI tools in three stages. Using the developed program, micro-teaching classes were conducted twice. The study results are as follows. First, there was a change in the positive perception of AI (p<.05). Second, the understanding of AI educational technology tools was improved and the recognition of the usefulness of developing a curriculum-related program was expanded. Third, the importance of teacher competency development was learned through the micro-teaching, and the students' understanding of the learning process was expanded.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

Calibration of flow devices is important in several areas of pharmaceutical, flow chemistry and microfluidic applications where dosage of process liquids or accurate measurement of the flow rate is important. The process-oriented liquid itself might influence the performance of the flow device and the simultaneous determination of the dynamic viscosity under flow conditions might be a valuable information for the process parameters. To offer the simultaneous calibration of the dynamic viscosity of the process-oriented liquid at the corresponding flowrate, METAS has built a pipe viscometer for the traceable in-line measurement of the dynamic viscosity in the current flow facilities for low flow rates from 1 L/min to 150 mL/min and pressure drops up to 10 bar. The traceability of all the measuring quantities as well as the geometrical dimensions of the micro tube guarantee the traceability of the pipe viscometer to SI units. The most challenging part is the traceable determination of the inner diameter of the micro tube. This can be achieved by measuring the pressure drop as a function of flow rate with the pipe viscometer and applying the law of Hagen-Poiseuille with a traceable dynamic viscosity of a reference liquid (water) or perform the measurements with the micro-CT at METAS, which determines the inner diameter by x-ray diffraction. The validation of the stated measurement uncertainty of the pipe viscometer has been performed by means of calibration of the dynamic viscosity of several reference liquids with traceable density and kinematic viscosity. The setup of the facility, the traceability as well as the uncertainty calculation of the pipe viscometer for the in-line measurement of the dynamic viscosity are discussed in this paper.

Micro-expression (ME) is one of the key psychological stress reactions. It is a modest, spontaneous facial mechanism. ME has significant applicability in a variety of psychologically-related sectors because to its precision and unpredictability with regard to psychological manifestations. Nevertheless, the current Micro-expression recognition (MER) algorithms have poor accuracy and a limited quantity of ME data, and this study issue has not been thoroughly investigated. Therefore, we present an approach for deep learning based on a Spatio-temporal capsule network (STCP-Net). STCP-Net has four components: a jitter reduction module, a differential feature extraction module, an STCP module, and a fully linked layer. The first two modules are aimed to extract diversifying differential features more precisely and to limit the influence of head jitter. The STCP module is used to extract Spatio-temporal features layer by layer, taking the temporal and geographical connection between features into account. This research runs sufficient trials using the Leave One Subject Out (LOSO) methodology for cross-validation using the CASMEII dataset. The conclusion and analysis demonstrate that the algorithm is innovative and efficient.

Cancer stem cells (CSCs) are one of the cell types that account for cancer heterogeneity. They arrest in the G0 phase and generate non-CSC progeny by self-renewing and pluripotency activity, resulting in tumor recurrence, metastasis, and chemoresistance. One CSC can stimulate tumor relapse and can re-grow a metastatic tumor. So, CSC is a promising target for eradicating tumors, and developing an anti-CSC method has become a top priority in cancer therapy. In recent years competing endogenous RNA (ceRNA) have emerged as an important class of post-transcriptional regulators that affect gene expression via competition for microRNA (miRNA) binding. Furthermore, aberrant ceRNA expression is associated with tumor progression. To overcome therapeutic resistance due to CSCs, we need to improve our existing understanding of the mechanisms by which ceRNAs are implicated in CSC-related relapse. Thus, this review was designed in order to discuss the role of ceRNAs in CSCs function. We reviewed the role of ceRNAs in acquiring CSCs characteristics in the form of different pathways including Rho GTPase/F-actin_ Yes-associated protein (YAP)/transcriptional co-activator with PDZ-binding motif (TAZ) (Hippo), Wnt/β-catenin pathway, transforming growth factor (TGF)-b–urothelial carcinoma-associated 1 (UCA1)–Slug pathway, etc. Finally, considering the comprehensive impacts of the ceRNA network on different pathways, a treatment strategy driving the ceRNA network might be effective. Targeting ceRNAs may open the path for new cancer therapeutic targets and can be used in clinical research.

This research was specifically aimed at assessing the influence of sulfur in triple-super phosphate (TSP) on wheat yield. From the results, wheat showed response to sulfur (S) from gypsum (in 67%); and nitrogen (N) from urea in about 100% (of 24 sites). Based on this N was found to be the most limiting element to wheat production followed by sulfur, and then by phosphorus. TSP is tested to contain agronomically up to 2-6% by weight of S. However, wheat didn’t show response to S impurity supplied in the form of TSP. Though, not statistically significant, it is observed that there have always been yield increments by certain percent due to S from TSP in 8 out of 10 target sites, which is depicted in the increasing trends of yield response curves. From this it is learnt that, the benefits of the accidental/incidental application of such high analysis fertilizers can be many-folds in the quality attributes of wheat, if the soils of such investigation at the same time would contain significant amount of organic matter (OM). Indeed, such analysis would be vital in varietal specific nutrient requirement studies in precision-farming and/or in categorizing soils into fertility gradients and fertilizer recommendation domains.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

We review recent work on broadband RF channelizers based on integrated optical frequency Kerr micro-combs combined with passive micro-ring resonator filters, with microcombs having channel spacings of 200GHz and 49GHz. This approach to realizing RF channelizers offers reduced complexity, size, and potential cost for a wide range of applications to microwave signal detection.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Balínt Syndrome is an acquired disorder manifesting in the inability to recognize several objects at once (simultagnosia), inaccurate visually guided limb movements despite intact motor function (optic ataxia) and the inability to make accurate voluntary saccades to visual targets despite demonstrating unrestricted range of eye movements (ocular motor apraxia). Here we report the first case of a patient presenting with Balínt Syndrome caused by a platelet-derived growth factor receptor A mutation (PDGFRA)-induced Hypereosinophilic Syndrome (HES).

A novel hybrid cobalt phosphite, (H2DAB)[Co(H2PO3)4]·2H2O, has been synthesized by using slow evaporation method, in the presence of cobalt nitrate, phosphorous acid and 1,4- dia-minobutane (DAB= 1,4- diaminobutane) as a structure-directing agent. Single crystal X-ray diffraction analysis showed that the compound crystallizes in the P-1(n.2) triclinic space group, with the following unit cell parameters (Å, °) a = 5.4814 (3), b = 7.5515 (4), c = 10.8548 (6), α = 88.001 (4), β = 88.707 (5), γ = 85.126 (5), and V= 447.33 (4) Å3. The crystal structure was built up from cor-ner-sharing [CoO6] octahedra, forming chains parallel to [001], which are interconnected by H2PO3 pseudo-tetrahedral units. The deprotonated cations, residing between the parallel chains, interacted with the inorganic moiety via hydrogen bonds leading thus to the formation of the 3D crystal structure. The Fourier transform infrared spectrum showed characteristic bands corresponding to the phosphite group and the organic amine. The thermal behavior of the compound consisted mainly of the loss of its organic moiety and the water molecules. The biological tests exhibited significant activity against Candida albicans and Escherichia coli strains in all used concentrations, while less inhibitory activity was pronounced against Staphylococcus epidermidis and Saccharomyces cerevisiae, and in the case of multi-cellular organisms, no activity against the nematode model Steinernema feltiae was detected.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

In recent years, Web APIs have become a de facto standard for exchanging machine-readable data on the Web. Despite this success though, they often fail in making resource descriptions interoperable due to the fact that they rely on proprietary vocabularies that lack formal semantics. The Linked Data principles similarly seek the massive publication of data on the Web, yet with the specific goal of ensuring semantic interoperability. Given their complementary goals, it is commonly admitted that cross-fertilization could stem from the automatic combination of Linked Data and Web APIs. Towards this goal, in this paper we leverage the micro-service architectural principles to define a SPARQL Micro-Service architecture, aimed at querying Web APIs using SPARQL. A SPARQL micro-service is a lightweight SPARQL endpoint that provides access to a small, resource-centric, virtual graph. In this context, we argue that full SPARQL Query expressiveness can be supported efficiently without jeopardizing servers availability. Furthermore, we demonstrate how this architecture can be used to dynamically assign dereferenceable URIs to Web API resources that do not have URIs beforehand, thus literally ``bringing'' Web APIs into the Web of Data. We believe that the emergence of an ecosystem of SPARQL micro-services published by independent providers would enable Linked Data-based applications to easily glean pieces of data from a wealth of distributed, scalable and reliable services. We describe a working prototype implementation and we finally illustrate the use of SPARQL micro-services in the context of two real-life use cases related to the biodiversity domain, developed in collaboration with the French National Museum of Natural History.

This study investigated the roles of transactions cost in MSMEs access to finance. This was done by investigating the impact of transactions cost on access to credit from both MSMEs and financial institutions (commercial banks and microfinance banks). From the MSMEs’ side, borrowing experience, decision lag, firm size and borrowers’ distance to the loan office were investigated. On the financial institution’s side, the costs of information gathering, loan administration, monitoring and loan enforcement were investigated. We used the questionnaire survey method, in-depth interviews and case studies, as well as the annual financial statements of the banks. We identified interest rate and collateral value as constraints to access to finance for MSMEs. We also found financial institutions’ attitude to MSMEs access to credit was not friendly. Financial institutions need to do more to bring down transaction cost of lending. This hopefully can be achieved by investing more in agent banking which would lower operating costs, as well as spreading risk, and ultimately increase credit intermediation to small businesses.

Transportation electrification has been identified as a crucial shift to be made for achieving energy security and emission reduction targets. Electric Vehicles (EVs) play a significant role in achieving these targets; therefore, there is a growing trend to develop new EV technologies and associated infrastructure. Along with these developments, EVs' Quality of Service (QoS) aspects should be enhanced to increase the number of EVs on the road. Various QoS factors are defined to assess the QoS of EVs, and one of the two aims of this paper is to provide a comprehensive review of these factors. The other aim is to review recent developments of associated communication technologies which are essential for exchanging information between EVs and charging stations. This paper serves as a comprehensive review and useful reference for researchers working on QoS aspects of EVs and associated communication systems aiming to enhance the QoS.

The smart grid system, an improvised form of the traditional grid, is considered a critical cyber-physical system. Due to its complex combination of smart and legacy technologies, this technology is characterized by a wide range of features such as full duplex communication, advanced metering infrastructure, remote monitoring, and control. However, despite this system’s substantial environmental and socio-economic impact on modern life, it poses severe security vulnerabilities due to its integration and interconnected and interdependent cyber-physical components. Based on the rapid development of cyber-physical systems (CPS), academics and industries have investigated relevant techniques to enhance and strengthen the security measures of the SG system. The intrusion detection system is a countermeasure, a powerful safeguard against various cyber-attacks and threats. The contribution of the IDSs to the SG paradigm is examined in this study. A comprehensive review has been presented in this study, highlighting different techniques, basic ideas, and analyses. Besides discussing the contemporary pertinent research studies, the shortcomings of the existing IDS for the SG system are also identified with a recommendation for future research direction.

Visual data on the geographic distribution of carbon storage helps policy maker to formulate countermeasures on global warming. However, Taiwan, as an island showing diversity in climate and topography, had lacked valid visual data in distribution of forest carbon storage between the last to forest surveys (1993-2015). This study established a model to achieve an estimation that capable to demonstrate the distribution of forest carbon storage. This model uses land use, stand morphology, carbon conversion coefficient databases accordingly for 51 types of major forest in Taiwan. An estimation on 2006 was conducted and shows an overall carbon storage of 165.65 Mt C, with forest carbon storage per unit area of 71.56 t C ha–1, where natural forests and plantations respectively contributed of 114.15 Mt C (68.9%) and 51.50 Mt C (31.1%). By assuming no change in land use type, the carbon sequestration from 2006 to 2007 by the 51 forest types was estimated to be 5.21 Mt C yr–1 using historical tree growth and mortality rates. The result reflects the reality of the land use status and event of coverage shifting with time by combining to the two forest surveys in Taiwan.

The construction industry has witnessed the increasing use of digital tools and smart solutions, particularly, in the realm of buildings energy automation within the concept of smart cities. While to truly realize the potential benefits of smart cities, a broader scope of smart initiatives is required to support the transition from smart buildings towards smart neighbourhoods, appreciated as the critical unit of urban development. To support this interplay of smart solutions between buildings and neighbourhoods, this article aims to collect and review all smart solutions presented in existing scientific articles, technical literature, and realized European projects. These solutions are classified under two main sections of buildings and neighbourhoods, which are investigated through five domains: buildings energy-related uses, renewable energy sources, water, waste, and open space management. Showcasing the quantitative outcomes demonstrates the potential benefits of implementing smart solutions from buildings to neighbourhoods. Moreover, this research concludes that the true enhancement of energy conservation goes beyond the buildings’ energy component and can be genuinely achieved by integrating intelligent elements of the neighbourhood, due to their strong interdependencies. Future research is recommended to focus on assessing the effectiveness of these solutions towards resource conservation.

The use of smart grids has enabled a number of planning methods to be developed to optimize energy costs, Peak to Average Ratios (PARs), and consumer satisfaction for load management in industrial, commercial, and domestic sectors. From a technical point of view, achieving optimal outcomes requires Demand Side Management (DSM). In smart grids, utility companies and electric users communicate two-way using digital technology to make a sustainable and economic system. This paper proposes a novel framework within which an Energy Management Controller (EMC) keeps track of each appliance, its operational time, and the costs associated with them. Customers of smart grids are motivated to shift their Off-Peak Hours (OPH) from Peak Hours by presenting incentives in OPH. The metering devices would also save customers costs by preventing load shifting between high- and low-cost periods. In addition, the study proposes the bacterial foraging algorithm and grasshopper optimization algorithm for lessening power price and PAR without compromising user comfort (UC) through appliance planning. The simulation results on a practical test system advocate the high effectiveness and reliable performance of the proposed model.

A detection system, modeled in a graph, uses "detectors" on a subset of vertices to uniquely identify an "intruder" at any vertex. We consider two types of detection systems: open-locating-dominating (OLD) sets and identifying codes (ICs). An OLD set gives each vertex a unique, non-empty open neighborhood of detectors, while an IC provides a unique, non-empty closed neighborhood of detectors. We explore their fault-tolerant variants: redundant OLD (RED:OLD) sets and redundant ICs (RED:ICs), which ensure that removing/disabling at most one detector guarantees the properties of OLD sets and ICs, respectively. This paper focuses on constructing optimal RED:OLD sets and RED:ICs on the infinite king's grid, and presents the proof for the bounds on their minimum densities; [3/10, 1/3] for RED:OLD sets and [3/11, 1/3] for RED:ICs.

We applied evolutionary game theory to extend a resource constrained security game model for confidentiality attacks in an Advanced Metering Infrastructure (AMI), which is a component of IoT-enabled Smart Grids. The AMI is modelled as a tree structure where each node aggregates the information of its children before encrypting it and passing it on to its parent. As a part of the model, we developed a discretization scheme for solving the replicator equations. The aim of this work is to explore the space of possible behaviours of attackers and to develop a framework where the AMI nodes adaptively select the most profitable strategies. Using this model, we simulated the evolution of a population of attackers and defenders on various cases resembling the real life implementation of AMI. We discuss in depth how to enhance security in AMI using evolutionary game theory either by a priori analysis or as a tool to run dynamic and adaptive infrastructure defence.

This paper proposes a game-theoretic framework for quantifying effects of strategic bidding behavior of load aggregators (LAs) on wholesale electricity market equilibrium. The independent system operator (ISO) employs double-sided auction design to settle transactions in the wholesale electricity market. Generating companies (GENCOs) and LAs submit their bids to the ISO in the economic model of supply function equilibrium. Under the smart grid paradigm, a LA participates in the electricity market on behalf of end-consumers to minimize their total payment for purchasing electricity. In this paper, bi-level programming (BLP) method is employed to determine optimal bidding strategy of self-interested market participants. In the upper level, the profit of intended market participant is maximized and in the lower level, the ISO clears the market via a bid-based security constrained economic dispatch (SCED). Also, competition of GENCOs and LAs is modeled as a non-cooperative game. To examine the effects of strategic bidding behavior of LAs on market equilibrium, the proposed model is applied to the IEEE 9-bus and the IEEE 30-bus test systems. According to numerical results, to allow the LAs to behave strategically along with the GENCOs makes the former better off and the latter worse off, while the net effect of this on total social welfare turns out to be case-contingent.

Frequency, amplitude and phase information of the grid voltage are of great importance in constructing a robust controller structure for grid connected inverter systems. This paper presents a simple and robust approach for the instantaneous estimation of positive and negative sequence voltage components under distorted voltage conditions. A second order generalized integrator (SOGI) is used to filter the distorted voltage and to generate orthogonal voltage components for each of the three phases. These filtered and orthogonal components are used for instantaneous calculation of symmetrical components. The implemented method is frequency adaptive; the method is demonstrated and compared to a conventional phase locked loop (PLL) technique with both MATLAB/Simulink simulations and experiments utilizing the dSPACE ds1103 digital controller.

The use of e-scooters and e-bicycles has been on the rise with an increased medical and financial burden. Our purpose was to identify risk factors for increased medical charges and recommend appropriate steps. We studied a retrospective cohort presenting to a level 1 urban trauma center from January 2018 through July 2019 due to micro-mobility platforms. The primary outcome for comparison was total billing cost and a regression analysis was performed to identify variables associated with higher cost. A total of 4073 patients were identified. The majority of which were males (67%), aged 20-30 years (41%). Helmet use reported in only 39.8%. Radiologic studies were performed more often in the e-bicycle group. Total billing charges amounted to 28.3 million New Israeli Shekels ($7.9 million). Average total cost was higher for e-bicycle injuries and in non-helmet users. Other factors associated with higher cost were age, and time of day 12:00-18:00. We recommend that urban cities invest in infrastructure in advance to micro-mobility introduction, regulate the use of e-platforms, designate resources for education on personal protective equipment and prepare medical centers in advance.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

This research investigates the microstructure and mechanical behaviour of a polylactic acid (PLA)-iron (PLI) composite designed to enable magnetic actuation. Tensile specimens of PLI are produced through Fused Filament Fabrication, incorporating diverse printing angles ranging from 0° to 90°, thereby facilitating the creation of a variety of layups. The microstructure of these 3D-printed composites is analysed using X-ray micro-tomography. Furthermore, the tensile mechanical properties of all composites are evaluated, and the findings are deliberated in relation to the conditions of the printing angle. Additionally, the fractography of broken specimens is examined using Scanning Electron Microscopy. The findings indicate that the printing angle plays a significant role in influencing the tensile properties of the 3D-printed PLI composites, particularly in adjusting mechanical anisotropy. Moreover, an optimal layup of 45°/45° is attained, resulting in an enhanced ranking of the tensile performance. These findings related to 3D-printed PLI composites present a cost-efficient option for manufacturing bio-sourced light-adaptive composites through 3D printing, enabling the generation of intricate magnetic actuation performance.

A fern, Polypodium aureum, possesses a specialized spore-releasing mechanism like a catapult induced by quick expansion of vaporized bubbles. This study introduces lipid-coated perfluorocarbon droplets to enable repeatable vaporization-condensation cycles, inspired by the repeatable vaporization of Polypodium aureum. Lipid-perfluorocarbon droplets have been considered not to exhibit repeatable oscillations due to bubble collapse by low surface tension of lipid layers. However, a single lipid-dodecafluoropentane droplet with a diameter of 9.17 µm shows expansion-contraction oscillations over 4,000 cycles by changing lipid composition and applying low power of 1.7 MHz ultrasound to induce partial vaporization of droplets. The optimal combinations of shell composition, droplet fabrication, and acoustic conditions can minimize damage on shell structure and quick recovery of damaged shell layers. The highly-expanding oscillatory microbubbles provide a new direction for fuel-free micro or nanobots as well as biomedical applications of contrast agents and drug delivery.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

Traumatic brain injury (TBI) affects millions of people annually, however, our knowledge of the diffuse pathologies associated with TBI is limited. As diffuse pathologies, including axonal injury and neuroinflammatory changes, are difficult to visualize in the clinical population, animal models are used. In the current study we used the central fluid percussion injury (CFPI) model in a micro pig to study the potential scalability of these diffuse pathologies in a gyrencephalic brain of a species with inflammatory systems very similar to humans. We found that both axonal injury and microglia activation within the thalamus and corpus callosum are positively correlated to the weight-normalized pressure pulse, while subtle changes in blood gas and mean arterial blood pressure are not. We also found that the majority of tissue generated up to 10 years previously is viable for immunofluorescent labeling after long-term refrigeration storage. This study indicates that a micro pig CFPI model could allow for specific investigations of various degree of diffuse pathological burdens following TBI.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

This review paper delves into using micro-credentials in higher education ecosystems as a digital enablers. Micro-credentials, which are digital credentials that attest to a learner’s mastery of a specific skill or knowledge area, are becoming more popular in higher education. The paper examines the successful implementation of micro-credential frameworks in higher education, using case studies to demonstrate the advantages of micro-credentials. The review emphasizes the agility and flexibility of microcredentials, which enable learners to acquire new skills quickly and respond to changes in the job market. In addition, the paper discusses the digital nature of micro-credentials and how they allow institutionsto provide targeted, skills-based training that isrelevant to employers. It also explores how micro-credentials are delivered through online platforms, making them convenient and easily accessible for learners. The review underscores the significance of digital infrastructure, connectivity, and public utility for promoting micro-credentials. The paper argues that micro-credentials function as a digital enabler for higher edu- cation ecosystems, allowing learners to acquire targeted training and enabling institutions to expand their offerings and reach more students. The paper concludes by highlighting the potential for micro-credentials to help bridge the skills gap and equip learners with the skills necessary to succeed in today’s digital economy.

Micro-level language policy and planning (LPP) primarily concerns local actors' decision-making on matters in relation to language(s) and its users. Despite a growing body of literature focusing on micro language planning in educational settings, there is a scarcity of research examining early childhood education settings such as micro-level LPP context for young English language learners. By adopting a case study approach, the present study examined the educators' enactment of agency in micro-planning the English language education policy (LEP) in one Chinese kindergarten and the associated factors shaping their agency. Our study revealed that the sustainable implementation of the kindergarten English LEP depended on the principal, native English-speaking teachers, and the Chinese assistant teachers' different degrees of agency. Also, the research findings indicated an array of contextual and individual factors nested in a hierarchical structure that facilitated, guided, and constrained the educators' agency in a role-and circumstance-dependent manner. This study contributes to the pertinent literature by casting nuanced light on the different educators' contributions to the micro-level LPP against a national policy that does not endorse early-year English language education.

The study purpose was to train and validate a deep-learning approach to detect micro-scale streetscape features related to pedestrian physical activity. This work innovates by combining computer vision techniques with Google Street View (GSV) images to overcome impediments to conducting audits (e.g., time, safety, and expert labor cost). The EfficientNETB5 architecture was used to build deep-learning models for eight micro-scale features guided by the Microscale Audit of Pedestrian Streetscapes-Mini tool: sidewalks, sidewalk buffers, curb cuts, zebra and line crosswalks, walk signals, bike symbols, and streetlights. We used a train--correct loop, whereby images were trained on a training dataset, evaluated using a separate validation dataset, and trained further until acceptable performance metrics were achieved. Further, we used trained models to audit participant (N=512) neighborhoods in the WalkIT Arizona trial. Correlations were explored between micro-scale features and GIS-measured- and participant reported-macro-scale walkability. Classifier precision, recall, and overall accuracy were all >84%. Total micro-scale was associated with overall macro-scale walkability (r=0.300,p<.001). Positive associations were found between model-detected and self-reported sidewalks (r=0.41,p<.001) and sidewalk buffers (r=0.26,p<.001). Computer vision model results suggest an alternative to trained human raters, allowing for audits of hundreds or thousands of neighborhoods for population surveillance or hypothesis testing.

A theoretical description of quantum jumps at the level of elementary particles is proposed, based on a micro-cosmological interpretation of their de Broglie phase. The third quantization formalism proposed in current literature for the description of baby universes in quantum cosmology is used here to describe the breakdown of unitarity in the transition from the pre-jump to the post-jump wave function. The corpuscular aspect manifested by the particle in the micro-interaction that originates the jump is represented by a pair of evanescent "micro-universes", respectively pre- and post-jump, connected by a wormhole. The latter represents the actual implementation of the interaction that leads to the projection on the outgoing state; this interaction is always local, even when the selected outgoing state is entangled. Therefore, the decoherence which leads to the emergence of classicality is originated by the same fundamental interactions of the Standard Model involved in the unitary evolution of the wave function. The objective nature of the reduction process admits implications on the possibility of using the formalism in the cosmological context, which are briefly discussed.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

During March and April 2020, the European Union (EU) was the center of the COVID-19 pandemic. Many National Governments imposed severe lockdown policies to mitigate the health crisis. The European Parliament commissioned a survey to analyse the citizens’ attitudes over a number of issues related to the COVID-19 pandemic. 21804 European citizens in 21 EU countries responded the survey between 23 April and 1 May 2020. The paper analyses empirically the individual satisfaction that European citizens have experienced over the measures taken by the respective National Governments to control the COVID-19 pandemic. The analysis is based on a micro-econometric model (ordered probit) that explains the citizens’ satisfaction by a number of attitudes and sociodemographic factors. Our results reveal that Spaniards are the least satisfied citizens in comparison with Danes, Irelanders, Greeks and Croats who are the most satisfied nationals. The years of education and the social class also play a determinant role. We also find that the most important determinant is the political support to the Government, and that those who are more worried by the economy and the protection of individual rights are usually more critic with the measures than those who are more worried by the health consequences.

Mineral profile of beef interests human health, but also animal performance and meat quality. This study analyzes the relationships of 20 minerals in beef (ICP-OES) with 3 animal performance and 13 meat quality traits analyzed on 182 samples of Longissimus thoracis. Animals’ breed and sex showed limited effects. The major sources of variation (farm/date of slaughter, individual animal within group and side/sample within animal) differed greatly from trait to trait. Mineral contents were correlated to animal performance and meat quality being significant 52 out of the 320 correlations at the farm/date level, and 101 out of the 320 at the individual animal level. Five latent factors explained 69% of mineral co-variation. The most important, “Mineral quantity” factor correlated with age at slaughter and with the meat color traits. Two latent factors (“Na+Fe+Cu” and “Fe+Mn”) correlated with performance and meat color traits. Two other (“K-B-Pb” and “Zn”) correlated with meat chemical composition and the latter also with carcass weight and daily gain, and meat color traits. Meat cooking losses correlated with “K-B-Pb”. Latent factor analysis appears be a useful means of disentangling the very complex relationships that the minerals in meat have with animal performance and meat quality traits.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

One of the ramifications of the COVID-19 pandemic is that it has lent urgency to ongoing discussions on mental well-being. While standard techniques are available to diagnose mental health disorders such as depression, anxiety, and stress, ambiguity persists regarding the emotional aspect of well-being. Emotional well-being (EWB) is a recently developed concept that seeks to understand the contribution of emotions to one’s well-being. Interactive approaches for such investigations are recommended to understand people’s contextual experiences. In this study, we use a qualitative approach to examine the psychological impact of the built environment on its residents to formulate the desiderata for an ideal place based on their perceptions. We use personal construct theory and the associated qualitative repertory grid technique. We recruited 15 students from the United Arab Emirates University and obtained information on their perceptions of three built environments they experienced. The findings revealed information on the students’ emotional constructs that were associated with a set of design-related factors, and the way the ideal hostel should be characterized in response to these associations. These findings enrich our knowledge of EWB within built environments and can inform their future design by considering the emotional aspect of the well-being of residents.

Integrating numerous renewable resources has been extensively researched and studied to create a dependable energy system. This study investigated the best techno-economical hybrid energy system configuration while using hydrogen energy to keep the system's energy balanced. Additionally, this study aims to determine the best hybrid system configuration for the location under investigation. A novel technique of DBM (Deterministic Balanced Method) was introduced to determine the total annual energy output for the project's lifetime. This approach is used to contrast the outcomes of other HOMER software tools. Then, using HOMER, it is possible to confirm the sizing optimization results for the suggested method by comparing the power ratings and yearly energy output. A detailed comparison between our proposed method and HOMER Pro has been conducted for validation and verification. Our method has been rigorously tested in various hybrid off-grid energy systems, ensuring its applicability and reliability across different scenarios and configurations. The results of our study indicate a high degree of similarity between the proposed approach and HOMER pro for computing annual energy power for the studied energy systems. Specifically, our analysis revealed that the difference between the approaches was within a range of 5%, indicating a high level of consistency and reliability in our method. These findings suggest that our approach can be confidently applied to determine the appropriate size of hybrid energy systems accurately. Overall, our study provides valuable insights into the development of effective sizing methodologies for hybrid energy systems. After considering the amount of solar radiation and wind speed gathered by global weather data platforms like NASA and METEONORM, this paper has also included a real case study of the Cairo International Airport's hybrid renewable energy production systems. To guarantee the viability of this study, the system design was founded on an actual load that was researched and simulated. A cluster of distributed networks was finally proposed to use the excess energy and enable energy conversion processes to be used in industry and transportation applications.

Remote sensing technology provides a new way to explore the earth for geoscience applications. In the context of continuous deepening of geological research and the vigorous development of geospatial information science, 3D geological modeling technology has become a research hotspot in the intersection of earth science and information science. The traditional 3D geological modeling technology refers to underground 3D modeling using geological data. This modeling method can only display the underground scene in 3D visualization, but cannot display the surface in detail. In this study, remote sensing technology is adopted to improve the traditional 3D geological modeling method, so that geological modeling can be integrated with remote sensing image, and a new 3D geological modeling method based on remote sensing technology is developed. This method can perform integrated 3D visualization of underground and aboveground scenes, which provides a new way for disaster prevention and reduction, geological prospecting and tectonic interpretation. The new 3D geological modeling method is mainly applied in the geological field, and has made new progress in multi-source heterogeneous geological data fusion, large-scale high-precision modeling, geological grid subdivision, attribute modeling technology, remote sensing image fusion and other aspects. Taking the Ya'an area as an example, this paper makes use of the new generation of 3D geological modeling technology to carry out 3D geological modeling and visual display. The 3D visualization in Ya'an area verifies the feasibility and effectiveness of the new 3D geological modeling method based on remote sensing technology in the current data environment.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

Conventional data visualization software have greatly improved the efficiency of the mining and visualization of biomedical data. However, when one applies a grid computing approach the efficiency and complexity of such visualization allows for a hypothetical increase in research opportunities. This paper will present data visualization examples presented in conventional networks, then go into higher details about more complex techniques related to leveraging parallel processing architecture. Part of these complex techniques include the attempt to build a basic general adversarial network (GAN) in order to increase the statistical pool of biomedical data for analysis as well as an introduction to the project utilizing the decentralized-internet SDK. This paper is meant to show you said conventional examples then go into details about the deeper experimentation and self contained results.

Automatic recognition methods for non-stationary EEG data collected from EEG sensors play an essential role in neurological detection. The integrative approaches proposed in this study consists of Symlet wavelet processing, a gradient boosting machine, and a grid search optimizer for a three-level classification scheme for normal subjects, intermittent epilepsy, and continuous epilepsy. Fourth-order Symlet wavelets were adopted to decompose the EEG data into five time-frequency sub-bands, whose statistical features were computed and used as classification features. The grid search optimizer was used to automatically find the optimal parameters for training the classifier. The classification accuracy of the gradient boosting machine was compared with that of a support vector machine and a random forest classifier constructed according to previous descriptions. Multiple-index were used to evaluate the Symlet wavelet transform-gradient boosting machine-grid search optimizer classification scheme, which provided better classification accuracy and detection effectiveness than has recently reported in other work on three-level classification of EEG data.

Environmental assessment is a concept that has been designed to facilitate the present generation to meet their needs without compromising the ability of future generations to meet their own needs as well. Thus, this concept has drawn significant attention from various scholars, researchers and industrial practitioners around the world over the past three decades. Life Cycle Environmental Assessment (LCEA) is a widely metric used to assess the potential ecological impacts, which can be caused by electricity generating supply systems or by other systems than power production plants. However, the current LCEA model is biased and ineffective. Because, its omits factors that are increasingly contributing to the ecological degradation. This study has identified the omitted factors through a critical analysis of a set of previous journal articles conducted in the energy sector. In light of this, this study has developed a novel LCEA framework addressing those blind spots. The framework developed in this study is holistic in nature including all the life cycle stages of a power supply system such as Extraction of the Raw Material (ERM), Transport of Raw Material (TRM), Conversion of Raw into Electricity (CRE), and Transmission and Distribution of Electricity (TDE) to the end users. The novel developed LCEA model has been tested and applied to nine power generation plants such as coal, gas, nuclear, biomass, geothermal, hydro, solar thermal, wind onshore and wind offshore. The results have demonstrated that of conventional technologies including coal, gas, and nuclear, coal energy generating source has got the highest life cycle greenhouse gas Grid Emission Factor (GEF) of 2866 kg CO2e/MWh, followed by gas with 728 kg CO2e/MWh, and nuclear has got the least GEF of 35 kg CO2e/MWh. Whereas of renewable energy sources biomass has got the highest GEF of 1508 kg CO2e/MWh, followed by solar thermal with 46.6 kg CO2e/MWh, hydro 39 kg CO2e/MWh, wind offshore 25.25 kg CO2e/MWh, wind onshore 10.1 kg CO2e/MWh, and geothermal closes the ranking with 6.23 kg CO2e/MWh.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

Purpose: The objective of the study was to qualitatively assess micro-gap dimensions, connecting fitting surface profile and bacterial leakage of machined and cast high gold alloy UCLA abutments, with or without electrodeposited gold coatings attached to external hexagon implants. Materials and methods: 16 plastic UCLA (PUCLA) and 5 machined cast-to UCLA (GUCLA) abutments were cast with a high gold content alloy. 10 were electrolytically gold plated (8 - PUCLA, 2 - GUCLA). All abutments were attached to implants giving 21 implant-abutment combinations (IACs). External perimeter micro-gaps measured with SEM under different illumination and magnification conditions were averaged over three regions. The IACs were examined for E.coli leakage following an initial sterility test. Disassembled combinations were examined with SEM and surface profiles qualitatively assessed. Results: External micro-gap measurements did not reflect the variable connecting surface profiles but average values < 3.5 μm were observed for all IACs. Bacterial transfer was observed in 3 of 5 PUCLA plated and 2 of 5 PUCLA non-plated IACs. No transfer occurred in the 3 GUCLA non-plated or 2 GUCLA plated IACs. Abutment connecting surfaces, both Au plated and not Au plated, showed plastic deformation (smearing) in variable mosaic patterns across the micro-gap. External micro-gap dimensions although not truly reflective of surface connecting profiles averaged < 3.5 μm measured under shadow eliminating silhouette illumination for both cast and pre-machined external hexagon abutments with and without Au plating. Conclusions: Micro-gap dimensions < 5 μm were obtained with both high noble metal cast and pre-machined external hexagon abutments with and without Au electrodeposited on the abutment connecting surface. Regions of intimate contact due to plastic deformation (smearing) of these surfaces was observed. A continuous smeared region around the circumference of the surfaces can provide an effective barrier to egress of E.coli bacteria from the internal regions of the implant under static loading.

Micro-arc oxidation (MAO) is an emerging technology employed to produce high hardness or anti-corrosion ceramic coatings on lightweight metals such Al, Ti, Mg and their respective alloys. However, under non-lubrication conditions, such coatings exhibit relatively high friction coeffi-cients. To enhance the friction reduction properties of the MAO coatings, we employed a one-step MAO process with varying concentrations of graphene oxide (GO) in an aluminate sys-tem electrolyte to create composite coatings on the surfaces of Ti-6Al-4V alloy. The effect of concentrations of GO particles on microstructure, composition, and wear behavior of the result-ing composite coatings was investigated. Measurements of the coating's thickness, hardness, and roughness have also been conducted. Ball-on-disk friction test under dry condition were carried out to reveal tribological behavior of the MAO coating. The addition of graphene oxide in the electrolyte reduces the friction coefficient, with the composite coating containing 5 g/L of GO particles displaying the most effective friction reduction. Moreover, coating thickness increases with higher GO concentration. This friction reduction can be attributed to the particles in the coating acting as lubricants during friction, while GO also reduces adhesive damage, shifting the wear mechanism from adhesive to abrasive.

For the first time, an environmentally friendly waste-free closed cycle for the formation of EMI shielding materials that are promising for 5G communications is considered. Based on the proposed closed technological cycle, two types of EMI shielding materials have been obtained; both materials have significant prospects for signal shielding in all ranges that are allocated in different countries for 5G communication. The first type of materials are transparent conductive meshes with a transparency of more than 80% and with a shielding efficiency of more than 40 dB in the S and L bands and about 30 dB in the K and Ka bands. The study of signal reflection characteristics in the S, L, C, K and Ka bands showed the promise of using these materials as transparent 5G signal reflectors. The reflection coefficient in all considered ranges is above 90% (-0.5 dB). The second type of shielding material are continuous silver micro caps films characterized by a shielding efficiency of 90.1 dB at a thickness of 6.2±1.2 µm. We have also shown that silver micro caps can separate into silver flakes and ribbons when sonicated. These materials can also be used to produce EMI shielding coatings and composites. A detailed analysis of the shielding properties showed that each type of materials obtained in a closed technological cycle is comparable with the best literature results and significantly wins in terms of cost.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

This paper discusses the basic concepts of phase dislocations and vortex formation in the electric fields of fundamental air core mode of hollow core waveguides with specific types of rotational symmetry of the core – cladding boundary. Analysis of the behavior of the electric field phase in the transmission bands shows that the mechanism of light localization in the hollow core waveguides with discrete rotational symmetry of the core – cladding boundary cannot be completely described by the ARROW model. For an accurate description of the phase behavior, it is necessary to account for phase jumps of the magnitude of π when passing through the phase dislocations.

Low pressure fluid transport (1) applications often require low and precise volumetric flow rates (2) including low leakage to reduce additional costly and complex sensors. A peristaltic pump de-sign (3) was realized, with the fluid’s flexible transport channel formed by a solid cavity and the wobbling plate comprising a rigid and a soft layer (4). In operation, the wobbling plate is driven externally by an electric motor, hence, the soft layer is contracted and unloaded (5) during pump-cycles transporting fluid from low to high pressure sides. A thorough characterization of the pump system is required to design and dimension the components of the peristaltic pump. To capture all these parameters and their dependencies on various operation-states, often complex and long-lasting dynamic 3D FE-simulations are required. We present, here, a holistic design methodology (6) including analytical as well as numerical calculations, and experimental valida-tions for a peristaltic pump with certain specifications of flow-rate range, maximum pressures, and temperatures. An experimental material selection process is established and material data of candidate materials (7) (liquid silicone rubber, acrylonitrile rubber, thermoplastic-elastomer) are directly applied to predict the required drive torque. For the prediction, a semi-physical, analyti-cal model was derived and validated by characterizing the pump prototype.

Structural and morphological properties of the hydronium-potassium jarosite microstructures were investigated in this work, and their electrical properties were evaluated. All microstructures were synthesized at a reasonable temperature of 343 K with a reduced reaction time of 3 hours. Increase in the pH from 0.8 to 2.1 decreased the particle sized from 3 µm to 200 nm and increasing the aging time from 0, 3 to 7 days resulted in semispherical, spherical and euhedreal jarosite structures, respectively. A Rietveld analysis also was done, finding that increasing pH, the amount of hydronium substitution by potassium in the cationic site also increases, having a 77.72 % of hydronium jarosite (JH) plus 22.29 % potassium jarosite (JK) at pH 0.8; 82.44 % (JH) and 17.56 % (JK) at pH 1.1, and 89.98 % (JH) plus 10.02 % (JK) at pH 2.1. The results obtained in this work show that the obtained hydronium potassium jarosite microstructures with reduced particle size and euhedreal morphology can be used as anode materials for improving the life time of lithium ion batteries, due that during the analysis of the voltage obtained using electrodes made with this particles and graphite, this ranged from 0.89 to 1.36 V.

Optical biopsy describes a range of medical procedures in which light is used to investigate disease in the body, often in hard-to-reach regions via optical fibres. Optical biopsies can reveal a multitude of diagnostic information to aid therapeutic diagnosis and treatment with higher specificity and shorter delay than traditional surgical techniques. One specific type of optical biopsy relies on Raman spectroscopy to differentiate tissue types at the molecular level and has been used successfully to stage cancer. However, complex micro-optical systems are usually needed at the distal-end to optimise the signal-to-noise properties of the Raman signal collected. Manufacturing these devices remains a critical challenge, particularly in a way suitable for large scale adoption. In this paper, we describe a novel fibre-fed micro-optic system designed for efficient signal delivery and collection during a Raman spectroscopy based optical biopsy. Crucially, we fabricate the device using a direct-laser-writing technique known as ultrafast laser assisted etching which is scalable and allows components to be aligned passively. The Raman probe has a sub-millimetre diameter and offers confocal signal collection with 71.3 ± 1.5% collection efficiency over a 0.8 numerical aperture. Proof of concept spectral measurements were performed on mouse intestinal tissue and compared with results obtained using a commercial Raman microscope.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

Brain tumors are frequently classified with high accuracy using convolutional neural networks (CNNs) and better comprehend the spatial connections among pixels in complex pictures. Due to their tiny receptive fields, the majority of deep convolutional neural network (DCNN)-based techniques overfit and are unable to extract global context information from more significant regions. While dilated convolution retains data resolution at the output layer and increases the receptive field without adding computation, stacking several dilated convolutions has the drawback of producing a grid effect. To handle gridding artifacts and extract both coarse and fine features from the images, this research suggests using a dilated parallel deep convolutional neural network (PDCNN) architecture that preserves a wide receptive field. To reduce complexity, initially, input images are resized and then grayscale transformed. Data augmentation has since been used to expand the number of datasets. Dilated PDCNN makes use of the lower computational overhead and contributes to the reduction of gridding artifacts. By contrasting various dilation rates, the global path uses a low dilation rate (2,1,1), while the local path uses a high dilation rate (4,2,1) for decremental even numbers to tackle gridding artifacts and extract both coarse and fine features from the two parallel paths. Using three different types of MRI datasets, the suggested dilated PDCNN with the average ensemble method performs better. The accuracy provided by the Multiclass Kaggle dataset-III, Figshare dataset-II, and Binary tumor identification dataset-I is 98.35%, 98.13%, and 98.67%, respectively. In comparison to state-of-the-art techniques, the suggested structure improves results by extracting both fine and coarse features, making it efficient.

The power generation structure and load characteristics in different provinces are quite different in China, and the distribution of peak regulating resources and demands is extremely unbalanced. Due to many factors such as low power marketization degree, shortage of peak regulating resources and block of transmission channels, the consumption of new energy is facing greater pressure. In order to improve the mutual aids in regional power grid, this paper proposes a two-layer optimization dispatching model considering the mutual aids of peak regulation resources between each province, and determines the optimal units startup mode and power output in each provinces, thus obtaining all the power supply output arrangements and the technical and economic indicators. Finally, take the actual regional power grid in China as an example, the simulation results show that the proposed model can significantly improve the new energy utilization rate, which verified the effectiveness and feasibility of the proposed model and methods in this paper.

The need for a relatively quick solution to the problem of providing highways with roadside service facilities necessitates the development of a series of appropriate standard projects. To increase the efficiency of these series, it is advisable to carry out the interconnection of space-planning solutions based on a particular module. Taking into account the variety of planning and landscape characteristics of the sites for the placement of objects of the mainline service, it seems advisable to choose as a module not a square or rectangular, but a triangular configuration, which allows in most cases to harmoniously block the modules. The proposed roof module in the form of a "regular" triangle facing the tetrahedron has a structural basis in the form of a single-tier rod spatial plate. The principal space-planning solutions of all four dozen objects from the approved nomenclature of the mainline service performed in the process of analyzing the possibilities show the real possibility of solving the development tasks on the basis of this system. The use of the proposed modular system makes it possible to successfully solve a number of tasks to reduce the harmful impact on the environment and effectively use renewable energy sources.

Presently power control and management play a vigorous role in information technology and power management. Instead of non-renewable power manufacturing, renewable power manufacturing is preferred by every organization for controlling resource consumption, price reduction and efficient power management. Smart grid efficiently satisfies these requirements with the integration of machine learning algorithms. Machine learning algorithms are used in a smart grid for power requirement prediction, power distribution, failure identification etc. The proposed Random Forest-based smart grid system classifies the power grid into different zones like high and low power utilization. The power zones are divided into number of sub-zones and map to random forest branches. The sub-zone and branch mapping process used to identify the quantity of power utilized and the non-utilized in a zone. The non-utilized power quantity and location of power availabilities are identified and distributed the required quantity of power to the requester in a minimal response time and price. The priority power scheduling algorithm collect request from consumer and send the request to producer based on priority. The producer analysed the requester existing power utilization quantity and availability of power for scheduling the power distribution to the requester based on priority. The proposed Random Forest based sustainability and price optimization technique in smart grid experimental results are compared to existing machine learning techniques like SVM, KNN and NB. The proposed random forest-based identification technique identifies the exact location of the power availability, which takes minimal processing time and quick responses to the requestor. Additionally, the smart meter based smart grid technique identifies the faults in short time duration than the conventional energy management technique is also proven in the experimental results.

The work addresses the problem of Power Quality (PQ) metrics (or indexes) suitable for DC grids, encompassing Low and Medium Voltage applications, including electric transports, all-electric ships and aircrafts, electric vehicles, distributed generation and microgrids, modern data centers, etc. The two main pillars on which such PQ indexes are discussed and built are: i) the physical justification, so the electric phenomena affecting DC grids and components (PV panels, fuel cells, capacitors, batteries, etc.), causing e.g. stress of materials, ageing, distortion, grid instability; ii) the existing standardization framework, pointing out desirable coverage and extension, similarity with AC grids standards, but also inconsistencies. The first point is made more clear and usable by a graphical overview of the discussed phenomena. On this basis PQ is interpreted beyond the usual low-frequency range, including thus supraharmonics and common-mode disturbance, and filling the gap with the Electromagnetic Compatibility domain. However, phenomena typical of EMC and electrical safety (such as various types of overvoltages and fast transients) are excluded. Suitable PQ indexes are then reviewed, suggesting integrations and modifications, to cover the relevant phenomena and technological progress, and to better follow the normative exigencies.

The knowledge of the precise anatomy and dimensions of the pulp chamber in the different teeth allows the odontologist to perform correct diagnosis, as well as treatment planning and moni-toring. The clinical practice has introduced cone-beam computed tomography (CB-CT) as a method to evaluate the morphology and dimensions of the pulp chamber. Nevertheless, micro-computed tomography (micro-CT) is regarded as the gold standard in approaching those topics. Here we have designed an algorithm that takes as input DICOM images from in vivo CB-CT of permanent molars to determine the accuracy CB-CT for evaluation of pulp chamber volume. The values were compared with those from in vivo CB-CT (rough and expert manipulated) and ex vivo micro-CT. The relative errors obtained with the volume calculated by the algorithm vs. the volume measured by micro-CT do not exceed 5.7%; also, no significant differences were found between algorithm volumes vs. manipulated CB-CT volumes while all volumes were different from those obtained with automatic CB-CT software. These data demonstrate that volume algorithm CB-CT based may be a reliable technique for evaluation of the pulp chamber volume in permanent molars and can be useful in the diagnosis of pulp diseases, as well as in the planning and monitoring of their treatments.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

With the increasing demand for energy worldwide, researchers from different fields have been striving to improve the sustainability and proper utilization of energy resources. Passive radiative cooling, as a natural energy transport method, can achieve cooling without additional external energy input. This review provides a comprehensive examination of passive radiative cooling, including its fundamental theories and latest development. A particular emphasis is placed on the diverse range of fields where passive radiative cooling has been applied, notably including but not limited to construction and architecture. The current state of applications, potential challenges that may arise with wider adaption and promising research directions for each field are thoroughly discussed. This review underscores the universal applicability and feasibility of passive radiative cooling and contributes to its future development by identifying promising areas for further exploration.

This study addressed the need for efficient data collection in micro-mobility using low-end hardware, focusing on developing a system capable of handling large real-time data streams. We proposed a novel data collection system that leverages incremental learning techniques, enabling AI-based services for micro-mobility passengers through smartphones. Our approach utilizes 3-axis acceleration sensors integrated into micro-mobility devices, collecting motion data in real-time. This data is processed through an incremental learning pre-processing server, employing the Broad Learning System algorithm, to ensure robust performance in noisy, real-world environments. The use of incremental learning is pivotal, allowing our system to adapt continuously to new data, enhancing the accuracy and relevance of the AI services provided to passengers. This research not only advances the technical capabilities in micro-mobility data handling but also has the potential to enhance the overall passenger experience through improved AI-based services.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

(1) Background: OCT imaging has been used to assess enamel demineralization in dental research but is not yet developed enough to qualify as a diagnostic technique in clinics. The current capabilities of most commercial acquisition software allow for visual and qualitative assessment. There is a need for a fast and verified batch-processing algorithm for segmenting and analyzing the de-mineralized enamel. This study suggests a GUI MATLAB algorithm for processing and quantitative analysis of the demineralized enamel. (2) Methods: A group of artificially demineralized human enamels was in vitro scanned under the OCT, and ROI frames were extracted. By using a selected intensity threshold colormap, inter- (Ie) and intra- (Ia) prismatic demineralization can be segmented. A set of quantitative measurements for average demineralized depth, average line profile, and integrated reflectivity can be obtained for an accurate assessment. Real and simulated OCT frames were used for algorithm verification. (3) Results: A strong correlation between automated and known Excel measurements for the average demineralization depth was found (R² > 0.97). (4) Conclusions: OCT image segmentation and quantification of the enamel demoralization zones are possible. The algorithm can assess the future development of a real-time assessment of dental diagnostics using an oral probe OCT.

Our recent work has focused on the application of infinite group theory and related algebraic geometric tools in the context of transcription factors and microRNAs. We were able to differentiate between “healthy" nucleotide sequences and disrupted sequences that may be associated with various diseases. In this paper, we extend our efforts to the study of messenger RNA metabolism, showcasing the power of our approach. We investigate (i) mRNA translation in prokaryotes and eukaryotes, (ii) polyadenylation in eukaryotes, which is crucial for nuclear export, translation, stability, and splicing of mRNA, (iii) miRNAs involved in RNA silencing and post-transcriptional regulation of gene expression, and (iv) the identification of disrupted sequences that could lead to potential illnesses. To achieve this, we employ (a) infinite (finitely generated) groups fp, with generators representing the r+1 distinct nucleotides and a relation between them [e.g., the consensus sequence in the mRNA translation (i), the poly(A) tail in item (ii), and the miRNA seed in item (iii)], (b) aperiodicity theory, which connects “healthy groups" fp to free groups Fr of rank r and their profinite completion F^r, and (c) the representation theory of groups fp over the space-time-spin group SL2(C), highlighting the role of surfaces with isolated singularities in the character variety. Our approach could potentially contribute to the understanding of the molecular mechanisms underlying various diseases and help develop new diagnostic or therapeutic strategies.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

Recent improvements within the fields of high-throughput screening and 3D tissue culture have provided the possibility of developing in vitro micro-tissue models that can be used to study diseases and screen potential new therapies. This paper reports a proof of concept study on the use of microvalve-based bioprinting to create laminar MSC-chondrocyte co-cultures as an in vitro model of autologous chondrocyte implantation (ACI), an established cellular therapy for osteoarthritis. Microvalve-based bioprinting uses microvalves to deposit cells suspended in a liquid in a consistent and repeatable manner. In this case MSCs and chondrocytes have been sequentially deposited into an insert based transwell system in order to create a laminar co-culture, with variations in the ratios of the cell types used to investigate the potential for MSCs to stimulate improved repair. Histological and indirect immunofluorescence staining revealed the formation of dense tissue structures within the chondrocyte and MSC-chondrocyte cell co-cultures, alongside the establishment of a proliferative region at the base of the tissue. No stimulatory or inhibitory effect in terms of ECM production was observed through the introduction of MSCs, although the potential for an immunomodulatory benefit remains. This proof-of-concept study therefore provides a novel method to enable the scalable production of therapeutically relevant micro-tissue models that can be used for in vitro research to optimise ACI procedures.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes, while axial canal is the largest canal amongst the network and distributes at the center of a coral branch. However, previous studies indicated that, in the non-radial symmetry transport system of Acropora, axial canal do not play a major role in the transport of hydroplasm, and the action of axial canal in coral growth is still obscure. In this study, we reconstructed six Acropora muricata samples by high resolution micro-computed tomography to investigate the growth patterns of axial canals during the processes of new branch forming and truncated branch rebuilding. We found that the axial canal of a new branch is transformed from a calice and the polyps in the new branch are budded from the polyp in the axial canal. Meanwhile, the axial canal can transport the calcareous skeletons to rebuild the tip of a truncated branch, which represents as the change in the diameter of axial canal and calcareous deposition/reduction in it. This work indicate the regulation of axial canal in the growth processes including budding, branching, and mineralising of an Acropora colony.

Layered two-dimensional (2D) graphene oxide (GO) films are integrated with micro-ring resonators (MRRs) to experimentally demonstrate enhanced nonlinear optics in the form of four-wave mixing (FWM). Both uniformly coated and patterned GO films are integrated on CMOS-compatible doped silica MRRs using a large-area, transfer-free, layer-by-layer GO coating method together with photolithography and lift-off processes, yielding precise control of the film thickness, placement, and coating length. The high Kerr nonlinearity and low loss of the GO films combined with the strong light-matter interaction within the MRRs results in a significant improvement in the FWM efficiency in the hybrid MRRs. Detailed FWM measurements are performed at different pump powers and resonant wavelengths for the uniformly coated MRRs with 1−5 layers of GO as well as the patterned devices with 10−50 layers of GO. The experimental results show good agreement with theory, achieving up to ~7.6-dB enhancement in the FWM conversion efficiency (CE) for an MRR uniformly coated with 1 layer of GO and ~10.3-dB for a patterned device with 50 layers of GO. By fitting the measured CE as a function of pump power for devices with different numbers of GO layers, we also extract the dependence of GO’s third-order nonlinearity on layer number and pump power, revealing interesting physical insights about the evolution of the layered GO films from 2D monolayers to quasi bulk-like behavior. These results confirm the high nonlinear optical performance of integrated photonic resonators incorporated with 2D layered GO films.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.