This study presents the design and implementation of a PLC microprocessor adhering to the IEC-61131-3 standard, executed on a Cyclone-V FPGA using a DE10-NANO development board. Our microprocessor optimizes the central processing unit by streamlining the data path, achieving a remarkable simulated response time of approximately 60 ns, equivalent to three clock cycles at a 50MHz frequency for Boolean operations. To substantiate our approach, we conducted practical experiments utilizing a FESTO conveyor station, employing relays as actuators, and incorporating optical and inductive sensors. The results underscore the feasibility of our proposed approach and serve as practical validation of its efficacy. This work introduces a promising avenue for the development of cost-effective PLCs employing SoC FPGA variants. Additionally, a thorough comparison of execution times with other early reported architectures. Our microprocessor outperforms even well-established PLCs like the S7-312, with substantial reductions in execution times of 94.54% for floating-point operations, 71.42% to 93.33% for word operations, and up to 78.57% for bit operations.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

The rapid advancement of technology has led to increased electronic consumption and a corresponding rise in e-waste generation. To address this issue, this study develops a low-carbon e-commerce closed-loop supply chain (LCE-CLSC) system with remanufacturer, platform, and the government as key stakeholders. An evolutionary game approach is employed to investigate the system's dynamics, analyzing the impact of stakeholder strategies on system equilibrium. Numerical simulations reveal important findings: Firstly, government initiatives promoting recycling, carbon taxes on traditional products, can incentivize remanufacturers to produce low-carbon items and encourage platform investment in recycling services. Secondly, higher sales revenues motivate remanufacturers to produce low-carbon products. Thirdly, consumer sensitivity to recycling services strengthens waste recovery when platforms increase investments in these services, leading to remanufacturers choosing low-carbon production. Lastly, government subsidies may become ineffective if the cost of remanufacturers' carbon reduction and platforms' recycling services exceeds their affordability. These findings offer insights for the sustainable development of obsolete electronic product recycling systems.

Chronic Low Back Pain (CLBP), defined as pain persisting for at least 12 weeks, is a significant public health issue, with prevalence intensifying due to an ageing global population, amassing approximately 619 million cases in 2020 and projected to escalate to 843 million by 2050. Given the multitude of therapeutic modalities available for CLBP, this research sought to ascertain their respective efficacies in ameliorating pain and disability. We specifically scrutinized Multidisciplinary Biopsychosocial Rehabilitation (MBR) among adults enduring non-specific low back pain for over 12 weeks, excluding acute pain conditions and pre-study surgical interventions. MBR is an approach encompassing various modalities, including exercise, behavioral therapies, educational programs, and work conditioning aspects, necessitating a comprehensive Network Meta-Analysis (NMA) to fully grasp the extensive scope of its impact. The constructed network comprised diverse MBR modalities (behavioral, educational, and work conditioning) alongside exercise therapy (ET), minimal intervention, and usual care, serving as controls with pain and disability as outcomes. Through the analysis of 4,619 initially identified studies, 93 were included, encompassing a total of 8,059 participants. The NMA conducted substantiated that both ET and MBR modalities were notably effective in alleviating CLBP, with education-oriented MBR emerging as the most efficacious for pain mitigation and behavior-focused MBR for disability reduction. Nevertheless, the discerned differences amongst the treatments were minimal and uncertain, highlighting that no modality was definitively superior to the others. The analysis revealed low global and local inconsistency within the network, underscoring the reliability of the observed outcomes. Given the intricate nature of CLBP, embodying various facets, our findings advocate for a combined therapeutic approach to optimize treatment efficacy. Nonetheless, the presence of high study heterogeneity and potential biases necessitates cautious interpretation of the results, prompting future research.

Natural deep eutectic solvents (NADES) have been shown as selective and environmentally friendly solvents for the extraction of bioactive compounds. However, studies on the solubility of low molecular weight carbohydrates (LMWC) in NADES are scarce. In this work, new solubility data of LMWC in NADES are provided and a new approach based on the use of these solvents for the efficient fractionation of bioactive carbohydrates was explored for the first time. Several mono- and disaccharides and three NADES based on choline chloride (ChCl) and different donors [2-ethylene glycol (EtG), glycerol (Gly) and ethanedioic acid dihydrate (Eth)] were considered. While degradation of carbohydrates, mainly ketoses, was detected with ChCl:Eth due to its acidic nature, ChCl:EtG and ChCl:Gly were found to be useful alternatives for selectively separating bioactive ketoses and their corresponding aldoses (e.g. lactulose/lactose and tagatose/galactose) present in equimolar binary mixtures. In addition, the usefulness of ChCl:EtG for the selective enrichment of lactulose to be used as food ingredient or nutraceutical was proven (from a 25% in the reaction mixture to a 56% in the purified sample). NADES could be used for the selective fractionation of value-added carbohydrates from interfering sugars for several applications including food science, engineering or pharmaceuticals.

This study examined the impact of Vibration-Assisted Drilling (VAD) on hole quality and residual stress in Ti-6Al-4V ELI material. Ti-6Al-4V ELI possesses excellent mechanical properties but presents challenges in machining, including chip evacuation, burr formation, and elevated cutting temperatures. VAD, particularly Low-Frequency Vibration-Assisted Drilling (LF-VAD), has been explored as a potential solution to address these issues. The research com-pares LF-VAD with conventional drilling (CD) under various cutting and cooling conditions. LF-VAD exhibits higher maximum cutting forces under specific conditions, which result in accel-erated tool wear. However, it also demonstrates lower RMS (Root Mean Square) forces com-pared to CD, offering better control over chip formation, reduced burr formation, and improved surface roughness within the hole. Furthermore, LF-VAD generates greater compressive residual stresses on the hole's inner surface compared to CD, suggesting enhanced fatigue performance. These findings indicate that LF-VAD holds promise for improving hole quality, fatigue life, and overall component durability in Ti-6Al-4V machining applications.

Background Most of the Leber hereditary optic neuropathy (LHON) cases are bilateral and sequential, how-ever there are rare unilateral examples, or those in which the delay of onset of vision loss between one and the other eye is longer. In the case of presumed childhood amblyopia in one eye, the vision loss in the good eye may be the only symptom of bilateral disease, that was unnoticed in previ-ously amblyopic eye, or a preexisting episode of LHON on the “amblyopic” eye. Clinical decision in such cases may be difficult and suggestive for other forms of atypical optic neuropathy until confirmed by genetic testing. Case series We present three genetically confirmed (MT-ND1:m.3700G>A, MT-ND6:m14484 T>C, and MT-ND4:m.11778G>A) patients with subacute vision loss in previously good eye with the other eye believed to be amblyopic from the childhood, and their features different of what would be expected in true amblyopia. In all, electrophysiology testing showed bilaterally reduced ampli-tude of PERG with low VEP P100 wave amplitudes and prolonged peak time in both eyes, also unusual for amblyopia. During the follow-up, pallor of the optic discs progressed in all eyes. Significant thinning of the retinal nerve fiber layer around the optic disc (pRNFL) and ganglion cell complex (GCC) in the macular region was present. All three patients had peculiar history. First patient was treated for presumed hyperopic amblyopia that did not improve since child-hood and experienced visual loss on the good eye at the age of 17 and was negative for the three typical LHON mutations. Extended testing confirmed atypical pathogenic variant MT-ND1:m.3700G>A in homoplasmy. The second patient with presumed strabismic amblyopia had unusual presentation of vision loss only at the age of 61 and after exclusion of other causes, typical MT-ND4:m.11778G>A pathogenic variant was found in homoplasmy. The third case was peculiar as he had presumed strabismic amblyopia since childhood and had some degree of disc pallor in the amblyopic eye upon presenting with loss of vision on the good eye at the age of 21 and typical pathogenic variant m14484 T>C, p.Met64Val was subsequently confirmed. However, one year after the disease onset, he started to experience significant spontaneous functional im-provement in the non-amblyopic up to 1.0 Snellen, whilst improvement in the presumed amblyop-ic eye was modest, suggesting preexisting amblyopia. This interestingly extensive improvement was carefully followed by electrophysiology as well as visual acuity and fields. Conclusion This report shows three different scenarios of presentation of LHON in patients with presumed uniocular amblyopia from childhood. In such cases, the diagnosis may be difficult and detailed structural and functional evaluation of the optic nerve head is necessary to assess whether earlier LHON episode was misdiagnosed as amblyopia or whether LHON presented bilaterally on both eyes whilst only being noticed in the previously good eye.

Background:This study evaluated the effect of low-level laser therapy on postoperative pain and wound healing in children undergoing primary molar extractions.Methods:40children,6-10years of age, systemically healthy, and had atraumatic extraction indications of bilateral primary molar teeth were included in the study. First session randomly selected tooth was extracted under local anesthesia. In the control group, only the clot formation on the socket was observed and photographed. Other group extraction's performed 2weeks later. The LLLT group treated with980nm wavelength Doctor Smile Wiser diode laser and photographed. Non-epithelialized surface measurements performed with the ImageJ program. Pain assessment was performed with Wong-Baker Pain Scale. Statistical analyzes were performed with SPSS software.Results: There was no statistically significant difference in Wong-Baker values(p&gt;0.05). The laser group had more '0' values on days 1 and7; same values as the control group were recorded on other days. In soft tissue healing 3rd day evaluations, non-epithelialized surface of laser socket was found to be smaller than control group, and measurement results were found to be statistically significant(p&lt;0.05). The other days' measurement results were not statistically significant(p&gt;0.05).Conclusions:Although LLLT not found to be very effective in reducing postoperative discomfort after extraction of primary molars, it provides better wound healing in extraction sockets.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

Genetic adaptation of Hermetia illucens (BSF) to suboptimal single sourced wastes can open new perspectives for insect production. Here, four replicate BSF lines were maintained on a single sourced, low-quality wheat bran diet (WB) or on a high-quality chicken feed diet (CF) for 13 generations. We continuously evaluated evolutionary responses in several performance traits to rearing at the two diets. Subsequently, we tested responses to interchanged diets, i.e. of larvae that had been adapted to low-quality feed and to high quality feed and vice versa to evaluate costs associated with diet adaptation. BSF were found to experience rapid adaptation to the diet composition. While performances on WB diet were always inferior to CF diet, the adaptive re-sponses were stronger to the former diet. This stronger response was likely due to stronger se-lection pressure experienced by BSF fed on the low-quality single sourced diet. The interchanged diet experiment found no costs associated with diet adaptation but confirmed diet adaptation for the larval biomass and insect frass traits for the WB diet treatment. Our results revealed that BSF can rapidly adapt to diet through evolutionary responses, which has potential to be utilized to produce lines tailored to specific diets.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

Plastics are highly beneficial for the day-to-day activities of human beings; however, their decomposition is limited due to their strong covalent bonding. The concept of degradation of these big molecules into smaller ones or monomers was attempted by several researchers in the preceding decades with limited success. Pyrolysis is one of the ideas used to convert plastics into fuel, rather than small molecules, compared to the crowded structure of polymers. Among these plastics, low-density polyethylene (LDPE) is largely used as carry bags throughout the world, and, herein, the results of catalytic pyrolysis of the conversion of LDPE into fuel are reported. Different dosages of zinc oxide (ZnO) were used as a catalyst to do the pyrolysis at a specific temperature in a batch reactor specially designed at our laboratory. 0.6 g of ZnO was found to be the optimal dosage for a 50 g waste LDPE batch to get the maximum oil yield. The yielded oil was analyzed chemically through Fourier transform infrared spectroscopy (FTIR) and Reformulyzer M4 Hydrocarbon Group Type Analyzer. Evaluation of physical and chemical exergy along with exergetic efficiency of the process was done.

Children five years or younger in low- and middle-income countries (LMICs) are severely affected by diarrhoea disease, especially in the sub-Saharan region. Hence, the study aimed at determining the prevalence and determinants of diarrhea disease among children under 5 years in Epworth Township, Zimbabwe. A descriptive cross-sectional study was conducted at a local clinic in Epworth Township, Harare. A convenience sampling strategy was used to recruit study participants for participation and 386 children were enrolled in the study. The majority were male children (n=229; 59.3%), while there were more female caregivers (n=370; 95.9%) than male caregivers (n=16; 4.1%). The prevalence of diarrhea disease in the study was 25.1%. The determinants associated with diarrhea were being partially vaccinated (OR 2.38, CI 95% 2.80–8.22), collecting water more than 1 kilometre from a household (OR 4.55; CI 95% 2.10–9.85) and using untreated water (OR 6.22; CI 95% 2.13–18.20). The age of the caregiver and using a clean water container (OR 0.05; p=0.020) were protective factors. Provision of primary health care, especially prevention of disease through immunization and rendering environmental health services could reduce the prevalence of diarrhea in disadvantaged townships.

This study evaluates the agricultural carbon emission efficiency of Shandong Province from 2011 to 2020 using the DEA-SBM model. The nexus between endogenous and exogenous variables is estimated using the Tobit model. The findings reveal an overall increasing trend in agricultural carbon emissions, with significant variations in efficiency values among different cities, leading to a severe polarization. Spatial evaluation shows a high distribution trend in the central region and low in the eastern and western regions of Shandong Province. The empirical tests conducted for Shandong Province and its three regions indicate that urbanization plays a major role in sup-porting the growth of agricultural carbon emission efficiency, while the education level of the la-bor force has a suppressive impact. Economic development and crop cultivation structure, how-ever, have no significant influence. The impact of these variables varies across the eastern, central, and western regions. The proposed countermeasures include improving planting structure and reducing brain drain in the eastern region, strengthening agricultural and rural inputs and in-creasing the added value of agricultural products in the central region, and intensifying the link-age between urbanization and industrial layout in the western region to reduce agricultural car-bon emissions efficiency in Shandong Province.

Background: Current European guidelines support transcatheter aortic valve implantation (TA-VI) in intermediate to low-risk patients ≥75 years-old but its prognostic relevance is unknown. Methods: Intermediate-to-low-risk (Society of Thoracic Surgeon score <8%) patients enrolled in the HORSE registry were included. We compared the population with less versus more than 75 years old. The primary endpoint was all-cause mortality. Results: A total of 2685 patients were included, 280 (8.6%) <75 and 2405 ≥75 years. Through a mean follow-up of 437 ± 381 days, 198 (8.2%) and 23 (8.2%) patients died in the two arms, without statistically significant differences (log-rank p=0.925). At Cox regression analysis, age did not predict the occurrence of all-cause death, neither as a continuous variable (HR 1.01, 95% CI 0.99-1.04, p=0.294) nor dichotomizing according to the prespecified cutoff of 75 years (HR 0.97, 95% CI 0.63-1.51p=0.924). Time-to-event ROC curves showed low accuracy of age to predict all-cause mortality (area under the curve of 0.54 for both 1-year and 2-year outcomes). Conclusions: TAVI has comparable benefits across age strata in intermediate-to-low risk patients. The age cut-off suggested by current guidelines is not predictive of the risk of adverse events during hospital stay, neither of all-cause mortality through a mid-term follow-up.

The review presents the most developed by date hypotheses on the mechanisms of the influence of low-frequency magnetic fields (LFMF) on organisms. Biophysical models that explain the resonance-like responses of biological systems to LFMF with a specific frequency and amplitude are described. Two groups can be distinguished among these models: one considers ions-cofactors of proteins as the primary targets for the LFMF influence, and the other regards the magnetic moments of particles in biomolecules. Attention is paid to the dependence of resonance-like LFMF effects on the cell type. A radical-pair mechanism of the magnetic field's influence on biochemical processes is described with the example of cryptochrome. Conditions for this mechanism's applicability to explain the biological effects of LFMF are given. A model of the influence of LFMF on radical pairs in biochemical oscillators, which can explain the frequency-amplitude efficiency windows of LFMF, is proposed.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

Choosing new energy vehicles for travel, especially electric vehicles, is an important component of building a low-carbon urban transportation system. However, the charging need of electric vehicle users is still constrained by the unreasonable layout and insufficient supply of public charging piles in the city. Private charging pile sharing as an alternative policy tool can play a very good role in solving this problem. But it needs decision-makers in urban transportation to take corresponding measures to promote. This paper constructs an evolutionary game model to study the decision behavior of participants in private piles sharing platform. Through numerical simulation analysis, it is found that under most parameter conditions, the government tends to establish a shared charging pile platform based on public interests. Private charging pile owners are influenced by the relationship between the cost of supply modification and revenue, and they tend to join the shared platform when they expect to recover the modification cost. The research conclusions of this paper will provide support for exploring how participants make decisions to maximize overall benefits in the development of low-carbon urban transportation.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

The alteration of natural land cover to impervious surfaces during development increases stormwater runoff. Stormwater Control Measures (SCMs) are used to manage water quantity and enhance water quality by restoring the hydrologic cycle altered by development. Often, SCMs have an outflow pipe to handle overflows or to manage the release of water detained when infiltration is not possible. Traditionally, these are static controls (e.g. a small orifice is used to restrict the volume of outflow), however, these systems can be improved by instituting real-time controls (RTC). RTC improve the functionality of SCMs by dynamically controlling outflows to adjust to environmental conditions. A major impediment to the widespread implementation of RTC is the high cost of installation and operation. This study utilized machine learning methods to develop a forecasting approach for the implementation of low-cost RTC that were implemented on a programmable gate of the outlet structure of a multi-stage basin in southeastern Pennsylvania. The goals were to decrease the peak flow exiting the basin during rain events, increase the volume of water detained, decrease the number of overtopping events, maintain healthy vegetation in the basin, and protect the downstream vegetation from erosion. Multiple popular data science algorithms were evaluated including multiple linear regression and long short-term memory. These algorithms were used with a dataset, which consisted of four years of historical sensor data, collected in 5-minute intervals, to train models to predict water levels to optimize operations. The accuracy of 30 models with three different methods of handling missing values were compared. A long short-term memory model configured with a 30-minute lead time produced the best results. Having an approximate same lag time of 30 minutes for the contributing drainage area of the SCM provided a sufficient RTC functioning period to improve the performance of the outlet structure.

Advanced Hepatocellular carcinoma (HCC) is no longer a terminal illness. This change was mainly attributed to the development of new treatments including tyrosine-kinase inhibitors (TKIs), vascular endothelial growth factor (VEGF) inhibitors and immune checkpoint inhibitors (ICPIs) but the financial toxicity of treating advanced HCC is of a major concern specially in low middle-income countries (LMICs) where the patients are still battling for their most basic rights. Most of advanced HCC patients in LMICs have very limited accessibility to the new treatments including ICPIs. Searching for out of the box solutions to improve access to treatments -mainly ICPIs- is an utmost necessity for LMICs advanced HCC patients.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

In Japan, the prevalence of low birth weight (LBW) has been estimated to be approximately 10%, which is the highest among developed countries. This high prevalence might affect the prevalence of LBW-associated diseases in the adult population of Japan. Recently, LBW has been recognized as a contributing factor to post-adaptive focal segmental glomerulosclerosis (FSGS) in adulthood; however, few reports to date have evaluated the clinical and pathological characteristics of post-adaptive FSGS. A 13-year-old girl was referred to our hospital owing to mild proteinuria, which was detected at a school urinary screening. She was born at a gestational age of 23 weeks, with a very LBW of 630 g. Dipstick urinalysis revealed grade (2+) proteinuria. Her serum creatinine level was 1.02 mg/dL, and she was diagnosed as having stage 2 chronic kidney disease (CKD). Her serum uric acid level was 7 mg/dL. Her mother and 16-years old brother had hyperuricemia, too. A percutaneous renal biopsy leads to a diagnosis of FSGS. After 3 years of treatment with an angiotensin receptor blocker, her proteinuria decreased. However, her serum creatinine level was 1.07 mg/dL, and she still had stage 2 CKD. We considered that in this patient, the first hit was her LBW, and the second hit was hyperuricemia. The second hit might be associated with the development of CKD. The birth history of patients is not usually confirmed by nephrologists. Our case demonstrates that obtaining information regarding the preterm birth and LBW of patients is important in the diagnosis of noncommunicable diseases, because school urinary screening is not routinely performed in countries other than Japan.

The orthodontic treatment brings numerous benefits and, in most cases, the benefits outweigh the possible disadvantages. Root resorption (RR) is a common adverse phenomenon associated with orthodontic treatment. This study evaluates the role of low-level laser emission / Photobiomodu-lation (LE/P) in quantitative measurements of root resorption (QRR). The application of LE/P was done after each orthodontic activation with 4 types of treatment intervention (TI) on the RR after fixed orthodontic treatment (FOT) of the upper arch with ectopic eye tooth/teeth [EET]. 32 Orthodontic patients scheduled for FOT were selected and assigned to the 4 groups. These were LE/P+Self ligating bracket (SLB), LE/P+Conventional bracket (CB), Non-Photobiomodulation (non-LE/P)+SLB, and non-LE/P+CB. Standard management stages of FOT were followed in the maxilla. Each patient received a single application of LE/P labially/buccally and palatally, a total of 5 different points during each activation or appointment. The main outcome measure was QRR in maxillary anteriors before and after FOT assessed via cone-beam computed tomography (CBCT) using 3D OnDemand software. Insignificant QRR was found between before and after FOT in SLB, CLB, and LE/P, non-LE/P groups (p > 0.05). QRR in the SLB vs CB and LE/P vs non-LE/P group was significantly different in 11, 13, and 23 (p < 0.05). QRR in the LE/P+SLB group (p < 0.05) was significantly different in 11, 13, and 23 than that in the other groups. The most severe QRR was found on the 13 (0.88 ± 0.28mm and 0.87±0.27mm) and 23 (1.19 ± 0.14 mm and 1.16±0.13mm) in the CB and non-LE/P group (p < 0.001). LE/P+SLB showed highly significant superior outcome (p < 0.001) in relation to non-LE/P+CB, the QRR of 23 were 0.813± 0.114mm and 1.156± 0.166mm respectively. Significantly higher amount of QRR found in EET patients after FOT treated with the CB, non-LE/P, and non-LE/P+CB system and warrants further investigation to explore potential specific causes.

Although commercially-available low-cost air quality sensors have low accuracy, the sensor system are being used to collect the data for the regulation of PM2.5 emission caused by industrial activities or to estimate the personal exposure for PM2.5. In this work, to solve the accuracy problem of low-cost PM sensor, we developed a new PM2.5 calibration model by combining the deep neural network (DNN) optimized in calibration problem and a LSTM optimized in time-dependent characteristics. First, two datasets were generated to test the accuracy performance and generalization performance of the PM2.5 calibration machine learning (ML) model. The PM2.5 concentrations, temperature and humidity by low-cost sensor and gravimetric-based PM2.5 measuring instrument were sampled for a sufficiently long time. The proposed model was compared with benchmark (multiple linear regression model) and low-cost sensor results. For root mean square error (RMSE) for PM2.5 concentrations, the proposed model reduced 41-60% of error compared to the raw data of low-cost sensor, and reduced 30-51% of error compared to the benchmark model. R2 of ML model, MLR and raw data were 93, 80 and 59 %. Also, the developed model still showed consistent calibration performance when calibrated with new sensors in different locations. Low-cost sensors combined with ML model not only can improve the calibration performance of benchmark, but also can be applied to the sensor monitoring systems for various epidemiologic investigations and regulatory decisions.

Carbon farming is a capable strategy for more sustainable production of food and other related products. It seeks to produce the diverse array of natural farming methods and marketable products simultaneously. In agroforestry system, carbon sequestration is done by incorporating carbon dioxide (CO2) into plant biomass via photosynthesis. Carbon is, thus, stored in reserves of above-ground biomass, such as timber or branches, and below-ground biomass such as roots, or organic carbon in the soil. In addition to the significance of carbon sequestration in climate change mitigation, soil organic carbon (SOC) is an imperative indicator for the soil health as well as fertility. The change in SOC can explain whether the land use pattern degrades or improves the soil fertility. SOC, found in the soil in the form of soil organic matter (SOM), helps to improve soil health either directly or indirectly. Its direct consequence is related to the process of mineralization. Further, agroforestry is highly capable of generating huge amounts of bio-mass. In fact, agroforestry is believed to be particularly suitable for replenishment of SOC. Therefore, efforts should be made to convince farmers for their resource-use efficiency and soil conserving ability in order to get maximum benefits out of agriculture. According to food and agriculture organization (FAO,) agriculture, forestry, and other land use practices account for 24% of global greenhouse gas (GHG) emissions, and total global livestock emissions of 7.1 gigatons of CO2-equivalent per year, representing 14.5% of total anthropogenic GHG emissions. Agroforestry system that deliberately integrates trees and crops with livestock in the agricultural production could potentially increase carbon sequestration and decrease GHG emission from the terrestrial ecosystems, thus, helping in global climatic change mitigation. This study, therefore, aimed at clarification about carbon farming, modifications in carbon cycle and carbon sequestration during agricultural development in addition to benefits of agroforestry.

Low night temperature (LNT) can be a practical and economical target in tomato breeding programs in terms of energy saving in greenhouses. This study was conducted to investigate the physiological responses to LNT using four tomato accessions of cherry and large fruit types with LNT tolerance and sensitivity grown in two greenhouses with night temperature set-points of 10 and 15°C for heating. LNT significantly reduced plant height regardless of fruit types and LNT tolerance. The number of flowers were significantly reduced in 10°C in cherry but not in large fruit types. Fruit set in 10°C was significantly lower in LNT sensitive accessions than tolerant ones regardless of fruit types, which was due to abnormal flower morphology in 10°C. Proline accumulation patterns between 10 and 15°C significantly differed between fruit types as well as between LNT tolerant and sensitive accessions. Chlorophyll content in 10 °C was significantly higher at later growth stages in LNT tolerant accessions than sensitive ones in both fruit types. No clear difference in photosynthetic parameters was observed between fruit types or tolerance and sensitive accessions except for photosynthetic rate, which was significantly lower in tolerant than sensitive accessions during early growing period. These results suggest that different tomato fruit types may have different mechanisms for LNT tolerance.

This paper describes how to construct a low-cost magnetic levitation system (MagLev). The MagLev has been intensively used in the engineering education, allowing instructors and students to learn through hands-on experiments essential concepts, such as electronics, electromagnetism, and control systems. Built from scratch, the proposed MagLev depends only on simple, low-cost components readily available on the market. In addition to showing how to construct the MagLev, this paper presents a semi-active control strategy which seems novel when applied in the MagLev. Experiments performed in the laboratory have compared the proposed control scheme with the classical PID control. The corresponding real-time experiments illustrate both the effectiveness of the approach and the potential of the MagLev for education.

Additive manufacturing (AM) is an emerged layer-by-layer manufacturing process. However, its broad adoption is still hindered by limited material options, different fabrication defects, and inconsistent part quality. Material extrusion (ME) is one of the most widely used AM technologies, and, hence, is adopted in this research. Low-cost metal ME is a new and AM technology used to fabricate metal composite parts using sintered metal infused filament material. Since the involved materials and process are relatively new, there is a need to investigate the dimensional accuracy of ME fabricated metal parts for real-world applications. Each step of the manufacturing process, from the material extrusion to sintering, might significantly affect the dimensional accuracy. This research provides a comprehensive analysis of dimensional changes of metal samples fabricated by the ME and sintering process, using statistical and machine learning algorithms. Machine learning (ML) methods can be used to assist researchers in sophisticated pre-manufacturing planning and product quality assessment and control. This study compares linear regression to neural networks in assessing and predicting the dimensional changes of ME made components after 3D printing and sintering process. The prediction outcomes using a neural network performed the best with the highest accuracy as compared to regression. The findings of this study can help researchers and engineers to predict the dimensional variations and optimize the printing and sintering process parameters to obtain high quality metal parts fabricated by the low-cost ME process.

In this study, the external magnetic field emitted by a wireless power transfer (WPT) system and the internal electric field induced into human body models during recharging operations of a compact electric vehicle (EV) are evaluated. To this aim an ad-hoc formulation for the source modeling is coupled with a commercial software that performs numerical dosimetry. Specifically, two realistic anatomical models both in a driving position and in a standing posture are considered, and the chassis of the EV is modeled either as a currently employed aluminum alloys and as a futuristic carbon fiber composite panel. Aligned and misaligned coil configurations of the WPT system are considered as well. The analysis of the obtained results shows that the ICNIRP reference levels are exceeded in the driving position, especially for the carbon fiber chassis, whereas no exceedance is observed in terms of basic restrictions, at least for the considered scenarios.

Based on the theory of turbulence, equations are derived for estimations of turbulent fluctuations of the longitudinal and transverse components of the wind velocity during ideal hovering of a quadcopter in a turbulent atmosphere. We present the results of experiments which were carried out on the territory of the Geophysical Observatory of Institute of Monitoring of Climatic and Ecological Systems, Siberian Branch, Russian Academy of Sciences, located in Tomsk Akademgorodok on the territory with complex orography, in a parkland zone with buildings of research institutes and motorways. Time series of turbulent fluctuations of the longitudinal and transverse components of wind velocity fluctuations were received with the use of an automated weather station, and time series of estimates of these components, from data of a DJI Phantom 4 Pro quadcopter during hovering. According to the automated weather station data, anisotropy was observed in one experiment during measurements in the atmosphere, but this phenomenon was not observed in the other experiment: the fluctuation spectra of all components of wind speed fluctuations coincide. The spectra of fluctuations of the longitudinal and transverse wind velocity components based on the automated weather station data and UAV telemetry are presented. The fluctuation spectra of these components for the automated weather station data and quadcopter generally coincide. The behavior of the spectra coincides with the spectrum which corresponds to Kolmogorov–Obukhov “–5/3” law within the inertial range. The turbulent spectra of the wind velocity fluctuations obtained with the use of the automatic weather station and with the unmanned aerial vehicle differ in the high-frequency spectral region.

The IEEE 802.15.4-2015 standard includes the SUN (Smart Utility Networks) modulations, i.e., SUN-FSK, SUN-OQPSK and SUN-OFDM, which provide long range communications and allow to trade data rate, occupied bandwidth and reliability. However, given the constraints of low-power devices and the challenges of the wireless channel, communication reliability cannot still meet the PDR (Packet Delivery Ratio) requirements of industrial applications, i.e., PDR>99%. Hence, in this paper we evaluate the benefits of improving communication reliability by combining packet transmissions with modulation diversity using multiple IEEE 802.15.4g SUN modulations. The results derived from a real-world deployment show that going from 1 to 3 packet transmissions with the same SUN modulation can increase PDR from 85.0/84.6/71.3% to 94.2/94.1/86.0% using SUN-FSK, SUN-OQPSK and SUN-OFDM, respectively. Combining the same number of packet transmissions with modulation diversity allows to further increase the average PDR to 97.1%, indicating its potential as a tool to help meeting the reliability requirements of industrial applications.

Different cohort studies documented a lower glomerular filtration rate (GFR) in former extremely low birth weight (ELBW, <1000 g) neonates throughout childhood when compared to term controls. The current aim is to pool these studies to describe the GFR pattern over the pediatric age range. To do so, we conducted a systematic review on studies reporting on GFR measurements in former ELBW cases while GFR data of healthy age-matched controls included in these studies were co-collected. Based on 248 hits, 6 case-control and 3 cohort studies were identified, with 444 GFR measurements in 380 former ELBW cases (median age 5.3-20.7 years). The majority were small (17-78 cases) single center studies, with heterogeneity in GFR measurement (inulin, Cystatin C or creatinine estimated GFR formulae) tools. Despite this, the median GFR (ml/kg/1.73m²) within case-control studies was consistently lower (-13, range -8 to -25%) in cases, so that a relevant minority (15-30%) has a eGFR<90 mgl/kg/1.73m²). Consequently, this pooled analysis describes a consistent pattern of reduced eGFR in former ELBW cases throughout childhood. Research should focus on perinatal risk factors for impaired GFR and long-term outcome, but is hampered by single center cohorts, study size, and heterogeneity of GFR assessment tools.

We review the latest developments in the field of the metal-insulator transition in strongly-correlated two-dimensional electron systems. Particular attention is given to recent discoveries of a sliding quantum electron solid and interaction-induced spectrum flattening at the Fermi level in high-quality silicon-based structures.

Acquisition of real-time hydraulic data is an essential component for flood forecasting. However, we frequently face difficulties in obtaining discharge data using classical contact methods during high magnitude floods and for systems experiencing rapid hydro-geomorphological adjustment. Therefore, we developed low-cost, non-contact sensors and platforms that are designed to overcome these difficulties. These advances enable flood flow properties to be monitored at multiple locations across a river catchment, at low-cost, and communicated in near real-time by using an image velocimetry method. This is an optics-based approach for stream flow measurement using commercially available near-infrared digital cameras to acquire video footage in full HD (30fps). Video footage is then subjected to optical flow tracking techniques based on cross-correlation, and feature-based tracking, enabling the displacement rates of detected features (for example natural foam, seeds, woody debris, and turbulent structures) to be computed. This manual provides step by step guidance to install an image-based gauging station. It contains the list of necessary components, the calibration process of a new camera and the assembly procedure of the system.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

Low carbon cities are increasingly forming a distinct strand of sustainability literature. Models have been developed to measure the performance of low carbon cities. The purpose of this paper is to formulate a strategy-based model to evaluate current performance and predict future conditions of low carbon cities. It examines the dynamic interrelationships between key performance indicators (KPIs), induces changes to city plan targets and then instantly predicts the outcome of these changes. Designed generic and flexible, the proposed model shows how low carbon targets could be used to guide the transformation of low carbon cities under four strategies: (1) passive intervention, (2) problem solving, (3) trend modifying and (4) opportunity seeking. Further, the model has been applied to 17 cities and then tested on 5 cities: London, New York, Barcelona, Dubai and Istanbul. The paper concludes with policy implications to realign city plans and support low carbon innovation.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

The VLSI industry is facing parasitic effects that trouble development in the nanoscale domain. However, instead of replacing the traditional MOSFET design, it would be more advantageous to apply different doping profiles and discerning which deal with specific parasitic effects the best. With a review of Gaussian doping, Uniform doping, and Delta doping profiles and analysis of the FET technology characteristics that use these doping profiles, a comparison can be made among them for integrated circuit design engineers. These doping profiles are compared based on how well they perform against non-ideal and ideal environments. Also, both digital and analog performance are measured to ensure the uniqueness of each doping profile that is present. After getting a list of benefits from each doping profile, it is derived to determine which doping profile works best against a host of parasitic effects and what type of application do these doping profiles have

The crucial stages in the geochemical evolution of the Earth’s crust, ocean, and atmosphere could be explained by the assumed low-energy nuclear reactions (LENR) that are triggered by seismic activity. LENR result in the fission of medium-weight elements accompanied by neutron emissions, involving Fe and Ni as starting elements, and C, N, O as resultants. Geochemical data and experimental evidences support the LENR hypothesis. A spectral analysis of the period 1955-2013 shows common cycles between interannual changes in atmospheric CO2 growth rate and global seismic-moment release, whereas the trending behavior of the atmospheric CO2 was in response to the anthropogenic emissions. Assuming a correlation between such seismic and atmospheric fluctuations, the latter could be explained by cycles of worldwide seismicity, which would trigger massively LENR in the Earth’s Crust. In this framework, LENR from active faults could be considered as a relevant cause of carbon formation and degassing of freshly-formed CO2 during seismic activity. However, further studies are necessary to validate the present hypothesis which, at the present time, mainly aims to stimulate debate on the models which regulates atmospheric CO2.

Findings from studies of prenatal exposure to pesticides and adverse birth outcomes have been equivocal so far. We examined prenatal exposure to agricultural pesticides in relation to preterm birth and term low birthweight, respectively, in children born between 1998 and 2010 randomly selected from California birth records. We estimated residential exposures to agriculturally applied pesticides within 2 km of residential addresses at birth by pregnancy trimester for 17 individual pesticides and 3 chemical classes (organophosphates, pyrethroids, and carbamates). Among maternal addresses located within 2 km of any agricultural pesticide application, we identified 24,693 preterm and 220,297 term births, and 4,412 term low birthweight and 194,732 term normal birthweight infants. First or second trimester exposures to individual pesticides (e.g., glyphosates, paraquat, imidacloprid) or exposures to 2+ pesticides in the three chemical classes were associated with small increases (3-7%) in risk for preterm birth; associations were stronger for female offspring. We did not find associations between term low birthweight and exposures to pesticides other than for myclobutanil (OR: 1.11; 95% CI: 1.04-1.20) and possibly pyrethroids as a class. Our improved exposure assessment revealed that first and second trimester exposures to pesticides were associated with preterm delivery but few affected term low birthweight.

The gap of standardization for conducted and field coupled electromagnetic interferences (EMI) in the 2–150 kHz frequency range can lead to Electromagnetic Compatibility (EMC) problems. This is caused by power systems such as PWM controlled rectifiers, photovoltaic inverters or charging battery units in electric vehicles. This is a very important frequency spectral due to interferences generate in a wide range of dives and, specifically, communication problems in the new technologies and devices incorporated to the traditional grid to convert it into Smart Grid. Consequently, it is necessary to provide new solutions to attenuate this kind of interferences, which involve finding new materials able to filter the electromagnetic noise. This contribution is focused on characterizing the performance of different cable ferrite compositions in order to determine the effectiveness of most common materials such as MnZn and NiZn and a new range based on nanocrystalline solutions. This analysis procedure is carried out through two methods: theoretical method by determining the insertion loss through measuring impedance parameter and proposing a new empirical technique based on measuring directly the insertion loss parameter. Therefore, the main aim of this characterization process is to determine the performance of these cable ferrites to reduce the interferences in this controversial frequency range. From the results obtained, it is possible to deduce that nanocrystalline cable ferrites provide the best performance to filter the electromagnetic noise in the 2-150 kHz frequency range.

Emerging countries in Southeast Asia are facing considerable challenges in addressing rising motorisation and its negative impact on air quality, traffic, energy security, liveability, and greenhouse gas emissions. Indeed, even as initial policies to address these issues are being agreed and implemented, current trends are incompatible with sustainable development and long-term climate change targets. This paper presents a comparative analysis of the approach and status of sustainable, low-carbon transport policy in ASEAN countries and identifies differences and similarities, with the aim of helping assessment of feasibility of future policies and informing future studies on policy innovations and cross-country learning. The methodology is based on the taxonomy of policy components developed by Howlett and Cashore, and our data on comprehensive country studies for Indonesia, the Philippines, Thailand and Vietnam and interviews. We find that each country has a specific set of goals, objectives and targets that support sustainable transport, and, directly or indirectly, climate change mitigation. In terms of specific instruments and calibrations, which we analyse based on the Avoid-Shift-Improve approach, there are notable differences between the countries, for example in fuel economy policy.

Scene classification plays an important role in the intelligent processing of high-resolution satellite (HRS) remotely sensed image. In HRS image classification, multiple features, e.g. shape, color, and texture features, are employed to represent scenes from different perspectives. Accordingly, effective integration of multiple features always results in better performance compared to methods based on a single feature in the interpretation of HRS image. In this paper, we introduce a multi-task joint sparse and low-rank representation model to combine the strength of multiple features for HRS image interpretation. Specifically, a multi-task learning formulation is applied to simultaneously consider sparse and low-rank structure across multiple tasks. The proposed model is optimized as a non-smooth convex optimization problem using an accelerated proximal gradient method. Experiments on two public scene classification datasets demonstrate that the proposed method achieves remarkable performance and improves upon the state-of-art methods in respective applications.

A comprehensive evaluation system of rural building energy consumption from a innovative composite perspective is established, which is suitable for southwest China. the brainstorming method and Delphi method were used to establish the indicator system, the ANP method was applied to calculate the weights of the comprehensive evaluation model, the scoring criteria of all evaluation indexes are constructed based on fuzzy evaluation theory, the applicability of the model is verified by an example of the countryside around Chengdu. The results showed that the score of some factors is low, whole or part area, just like the percentage of clean energy use(C24), the thermal performance of external walls(E21), the implementation of energy-saving measures(S22), were key factors affecting the target level, which has greater potential for improvement. The distribution of comprehensive indicators and evaluation factors have certain spatial distribution characteristics, the overall spatial distribution shows the characterwastic of "high in the southeast and low in the northwest". The key factors and spatial distribution characteristics found can be used as an important basis for the improvement of green energy-saving promotion measures, energy-saving retrofit programmes were proposed in terms of additional solar room, energy-saving of external walls and air-conditioning temperature setting guidance.

Our hypothesis that controlled ozone applications interfere into the redox balance of the biological organism (first published in 1998 with a preclinical trial on protecting the liver from CCl4 intoxication), has been verified over the last 2 decades in reactive oxygen species (ROS)-induced mitochondrial pathologies, such as rheumatoid arthritis, osteoarthritis, aging processes, diabetes-2 and in prevention of intoxications. Low-dose ozone acts as a redox bioregulator: The restoration of the disturbed redox balance is comprehensible in a number of preclinical and clinical studies by a remarkable increase of the antioxidant repair markers, here mainly shown as glutathione increase and a reduction in oxidative stress markers, mainly malondialdehyde. The mechanism of action is shown, relevant data are displayed, evaluated and comprehensively discussed: The repair side of the equilibrium increases by 21% up to 140% compared to the non-ozone treated groups and depending on the indication; the stress markers are simultaneously reduced, the redox system regains its balance.

Amylose content (AC) stands as a pivotal determinant of rice grain quality, primarily governed by the Waxy gene (Wx), with its allelic diversity significantly influencing AC variation. In the current culinary landscape, soft rice varieties, known for their low AC and superior palatability, are particularly sought after by consumers. Notably, many soft japonica rice varieties cultivated in southern China, including the Nangeng series, are characterized by the presence of the Wxmp allele, derived from the ancestral Wxmq allele. While both alleles are associated with reduced AC, there remains a paucity of detailed understanding regarding the interplay between specific functional single nucleotide polymorphisms (SNPs) within these alleles and the overarching rice grain quality. Employing site-directed mutagenesis, we engineered three distinct transgenic rice lines, each harboring either the Wxmp, Wxmq, or Wxb-5c alleles, against the background of the glutinous rice cultivar Nip(wx). This suite of transgenic rice showcased a gradation ingrain transparency inversely correlated to AC, delineating a sequence from Wxmq, signifying the lowest, through Wxmp, to Wxb-5c, indicating the highest. Consequently, this gradation in AC precipitated variations in other rice grain physicochemical attributes, such as the taste value of cooked rice, gel consistency (GC), and starch pasting properties. Furthermore, analyses of gene expression and enzyme activity revealed that the functional SNPs, Ex4-53G/A and Ex5-53T/C, lead to a decline in the GBSSI enzyme activity without affecting expression levels. These findings underscore the potential of harnessing these SNPs in breeding programs aimed at developing soft rice varieties endowed with enhanced culinary qualities.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

The physiological process of iodine uptake in the thyroid is used for 131I treatment of thyroid diseases. Children are more sensitive to radiation compared to adults and may react differently to 131I exposure. The aims of this study were to evaluate the effects on thyroid protein expression in young and adult rats one year after 131I injection, and identify potential biomarkers related to 131I exposure, absorbed dose, and age. Twelve Sprague Dawley Rats (young and adults) were i.v. injected with 50 kBq or 500 kBq 131I and were killed twelve months later. Twelve untreated rats were used as age-matched controls. Quantitative proteomics, statistical analysis and evaluation of biological effects was performed. The effects of irradiation were most prominent in young rats. Protein biomarker candidates were proposed related to age, absorbed dose, thyroid function and cancer and a panel was proposed for 131I exposure. In conclusion, the proteome of rat thyroid was differentially regulated twelve months after low-intermediate dose exposure to 131I in both young and adult rats. Several biomarker candidates are proposed for 131I exposure, age, and many of them are known to be related to thyroid function or thyroid cancer. Further research on human samples are needed for validation.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

This paper provides an overview of current literature on community-led development initiatives in urban contexts, their role in addressing urban inequality, and the challenges they face. This study examines effective strategies of community-led initiatives, such as empowering communities, building partnerships, mobilizing resources, focusing on local needs, and participatory design methods. Case studies from around the world demonstrate how successful community-led development initiatives have been able to overcome obstacles to create more inclusive and equitable urban environments. Institutional support, including technical assistance, capacity building, and regulatory frameworks, are crucial for promoting the success and sustainability of these initiatives. Challenges to community-led initiatives include limited resources, capacity building needs, inadequate infrastructure, lack of institutional support, and lack of trust among community members. Therefore, the paper suggests that it is essential to address these challenges to enable the success of community-led development initiatives. Furthermore, this study recommends that future research should explore how emerging technologies and innovative approaches can effectively support community-led development initiatives and advance more just and sustainable urban development.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

(1) Background: This paper details the development process of two assistive technology products (ATs) implemented in the PAID project, aiming to promote the social, educational, and labor inclusion of people with disabilities across 10 municipalities of Antioquia, Colombia. (2) Methods: Applying Design Thinking (DT) methodology, including stages of empathizing, defining, ideating, prototyping, and testing, alongside a demographic study where specific needs of people with disabilities (PwDs) were identified. (3) Results: As a result, the construction process of two specific cases of assistive technology products (ATs) is detailed, including finite element simulation, mechanical testing, and delivery to end-users. Additionally, workshops for assistive product fabrication conducted in select municipalities of the project are highlighted. (4) Conclusions: the information gathered guided the development of the ATs, focusing on their features on accessibility and ease of replication. The primary objective is to facilitate the participation of PwDs in educational environments, thus promoting inclusion and accessibility. This article describes the results of two of these ATs; however, it is worth noting that this process was performed for 112 ATs delivered through the duration of the project.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Computed tomography (CT) is a widely employed imaging modality with diverse clinical applications in pediatric and adult populations, offering numerous advantages. Despite several alternatives to imaging modalities with ionising radiation, CT scans have demonstrated persistent global popularity, contributing to a substantial amount of effective radiation doses for patients. This exposure results in hazards, including stochastic effects that amplify the radiation-induced cancer risk proportionally to the radiation dose received. CT-related radiation comprises a substantial portion of cumulative effective doses within diagnostic radiology, specifically impacting younger patient cohorts undergoing repeated investigations for chronic diseases over time. Scientific literature over recent decades has explored various methods to mitigate radiation doses during medical imaging. One notable strategy involves implementing low-dose and ultralow-dose CT protocols, maintaining diagnostic efficacy in acute and non-acute medical and surgical conditions. Utilising innovative image reconstruction algorithms, such as iterative reconstruction and emerging deep-learning algorithms based on artificial intelligence, plays a pivotal role in achieving an approximately 80% reduction in patient radiation compared to standard doses. This review article discusses the significance of low-dose protocols across a spectrum of acute and chronic medical conditions affecting different body systems.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

This paper presents a Modified Gate Diffusion Input (MGDI) design with four inputs for Quantum-dot Cellular Automata (QCA) technology. QCA is a promising nanotechnology that offers benefits such as low power consumption, and high density, making it a potential alternative to CMOS technology. The proposed planar cell design has advantages over previous designs, including a 19% reduction in the number of cells, a 29% reduction in total energy consumption, and a 44% reduction in average energy loss at the same occupancy level. The proposed block is capable of implementing 21 basic combinational functions and various sequential functions. The simulation of functions in 18nm technology and energy consumption calculation indicates that the resulting circuits have improvements of 41%, 27%, 27%, and 20% compared to multiplexers, comparators, four-bit parity circuits, and single-bit memory, respectively. Additionally, the number of cells in the proposed circuits has improved by 10%, 7%, 22%, and 19%, respectively.

To systematically assess the effect size of different methods for patients with low back pain. PubMed, Cochrane Library, Web of Science, and Google Scholar. databases were searched in January 2023. This study has been developed in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) Statement. The key search terms were: “Low back pain”, “Back pain”, “SF-36”, “VAS”, “VASP”, “Roland-Morris”, “Oswestry Disability Index”, and “conservative treatment”. The risk of bias was determined for each randomized trial using the Cochrane Risk of Bias Tool, and the methodological index for non-randomized studies (MINORS). The outcomes included SF-36 Mental, SF-36 Physical, VAS, Roland-Morris, and Oswestry Disability Index. R 4.0.5 software was used, and standardized mean difference (SMD) and 95% confidence intervals (CI) were calculated for continuous outcomes, random model. Twenty-five studies were included. Depending on the outcome being measured, the effect size of different methods in treating low back pain varies from small to large as follows: SF-36 Mental (SMD = 0.39, p &lt; 0.0001), SF-36 Physical (SMD = 0.55, p &lt; 0.0001), VAS (SMD = -0.84, p &lt; 0.0001), Roland-Morris (SMD = -0.45, p &lt; 0.0001), and Oswestry Disability Index (SMD = -0.61, p &lt; 0.0001). Our meta-analysis indicates the positive effects of applying different methods in the treatment of low back pain. PROSPERO registration number: CRD42022371282

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

In order to balance the conflicts among mass flow rate, total pressure ratio, adiabatic efficiency and stall margin in a low-bypass transonic fan, the optimization of the rotor blade is implemented in this study. An advanced 3D optimization design system is adopted, and flow diagnostic methods based on vorticity dynamics are employed to discuss the flow field. Results indicate that by controlling the blade camber line curvature, significant improvements in the aerodynamic performance for the fan stage are achieved, the total pressure ratio is increased by 1.90%, while the adiabatic efficiency and mass flow rate are increased by 4.45% and 5.82%, respectively. Vorticity diagnosis suggest that there exists a close link between performance parameters and vorticity parameters in the axial fan/compressor, both azimuthal vorticity and boundary vortex flux have significant influences on the stage performance. Moreover, the boundary layer separation is accompanied by the spike of entropy and static pressure, while the derivation/gradient of these flow parameters would also suffer drastic changes under the effect of shock wave. The vorticity parameters could provide detailed flow information about the on-wall flow with high accuracy, which provides the researchers with a novel method for the turbomachinery aerodynamic design and analysis.

In recent years, frequent occurrences of low temperature disasters due to global climate change have significantly impacted the normal growth of crops. Research has indicated that inorganic selenium (which is more toxic) can not only enhance the effects of low temperature stress but also increase selenium content on plants; however, there is a scarcity of studies investigating the impacts of organic selenium and nano-selenium on crops. In order to investigate whether organic selenium and nano-selenium can enhance low-temperature tolerance and increase selenium content in pak choi (Brassica chinensis var. pekinensis. cv. ‘Suzhouqing’), different concentrations (0, 5, 10, 20 mg L-1) of exogenous selenium were applied in this experiment to assess their effects on plant growth, nutritional quality and antioxidant properties. RNA-Seq technology was used to sequence the transcriptome of the leaves. Based on the transcriptome data, a Weighted Gene Co-expression Network Analysis (WGCNA) was employed to construct a network that associates with physiological traits related to stress resistance. Two highly correlated gene co-expression modules were identified, and within them, nine hub genes associated with endocytosis, antioxidant stress, absorption, transport, and metabolism of selenium were discovered. The results indicated that the beneficial effects on yield and total selenium content under low temperature were attributed to (1) protection of photosynthetic pigments for enhancing photosynthetic capacity by the up-regulation of LHca2, LHcb1, LHca1, LHcb4 in KEGG pathway: photosynthesis-antenna proteins; (2) activation of antioxidant system for efficient ROS homeostasis such as SOD, POD and CAT by the genes such as Superoxide dismutase, Monodehydroascorbate and (3) selenium absorption by endocytosis, seleninum transportation by ABC transporter gene family and selenium metabolism related genes such as Cysteine synthase, Glutaredoxin. These findings provide a foundation for further investigation into the molecular mechanisms underlying the effects of organic selenium and nano-selenium on cyanochloride production at low temperatures.

A significant electromotive force is induced in the rotor circuit of a doubly fed induction generator (DFIG) due to its high vulnerability to grid faults. Therefore, the system performance must be increased with appropriate control actions that can successfully offset such abnormalities in order to provide consistent and stable operations during grid disturbances. In this regard, this paper presents a solution based on a combination of an energy storage-based crowbar and a rotor-side crowbar that makes the effective transient current and voltage suppression for wind-driven DFIG possible. The core of the solution is its ability to restrict the transient rotor and stator overcurrents and DC-link overvoltages within their prescribed limits, aiming to protect the DFIG and power converters, and consequently, improve the system’ ability to ride-through faults. Further, the capacity of an energy storage device for transient suppression is estimated. Finally, simulation results show that the proposed approach is effective in achieving transient control objectives precisely and maintaining a stable grid connection during the faults.

This research delves into the impact of complex low-speed wake flow structures on the aerodynamic characteristics of objects downstream. It employs the proper orthogonal decomposition (POD) method and the domain precursor simulation method to compare traditional methods and validate this approach. The study generates several flow structures of parallel dual-cylinder wakes with different scales and spacing. The variations in the aerodynamic coefficient of three downstream objects at various times passing through wakes of varying scales are appropriately compared and analyzed. The study establishes that the wake with a cylinder spacing of G=1.5 has a more compact and concentrated modal structure than that with a cylinder spacing of G=0.35. Smaller objects are more responsive to the wake flow structure with a spacing of G=1.5, whereas larger objects respond more to the flow structure with a spacing of G=0.35. The achieved results also reveal that the aerodynamic force coefficients of objects passing through the wakefield at different times are closely related to the temporal characteristics of the wake flow structure with different scales.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

Due to the severe environmental impact of the CO2 emissions associated with the production of Ordinary Portland Cement (OPC) and the increasing demand for this commodity material, the development of alternative products has become a global concern. One alternative to OPC, or alitic-based clinkers, are amorphous-wollastonitic low calcium hydraulic binders (AWLCs). This new class of hydraulic binders, described in the literature for the first time in 2015, may significantly reduce the CO2 emissions associated with its production, resulting from its lower calcium content, but also from the fact that its production technology can be fully electrified. In this paper it is provided a state-of-the-art review, providing a comprehensive description on the latest research, summarizing both the physico-chemical and mechanical characteristics for this type of hydraulic binders, as well as possible routes for its production at an industrial scale.

Background: Chronic non-specific low back pain (CNSLBP) is defined as back pain that lasts longer than 12 weeks. Objectives: To investigate the efficacy of manual therapy (MT) program combined with Capacitive and Resistive Electric Transfer (TECAR) therapy in individuals with CNSLBP. Method: Sixty adults with CNSLBP were randomly equally divided into three groups. The first group followed an MT protocol in the lumbar region (MT group), the second group followed the same MT protocol combined with TECAR therapy (MT + TECAR group) using a conventional capacitive electrode as well as a special resistive electrode bracelet and the third group (Control group) received no treatment. Both intervention programs included six treatments over two weeks. Pain in the last 24 hours with the Numeric Pain Rating Scale (NPRS), functional ability with the Roland-Morris Disability Questionnaire (RMDQ), Pressure Pain Threshold (PPT) in the lumbar region with pressure algometry, and mobility of the lumbo-pelvic region through fingertip-to-floor distance (FFD) test were evaluated before and after the intervention period with a one-month follow-up. Analysis of variance with repeated measures was applied. Results: In the NPRS score, both intervention groups showed statistically significant differences compared to the control group both in the second week as well as in the one-month follow-up (p < .001). Between-groups differences were also noticed between the two intervention groups in the second week (p < .05). Differences in the RMDQ score in the second week and on the one-month follow-up were detected between the intervention groups and the control group (p < .001), while differences between the two intervention groups were only detected in the one-month follow-up (p < .001). Regarding the PPT values, differences were found mainly between the MT + TECAR and the control group and between the MT + TECAR and the MT group (p < .05), with the MT + TECAR group in most cases showing the greatest improvement compared to the other two groups, which remained statistically significant in the one-month follow-up (p < .05). Finally, both intervention groups improved the mobility of the lumbo-pelvic region in both time points compared to the control group without, however, statistically significant differences between them (p> .05). Conclusion: The application of an MT protocol with TECAR therapy appeared more effective than conventional MT as well as compared to the control group in reducing pain and disability and improving PPT in individuals with CNSLBP. No further improvement was noted in mobility of the lumbo-pelvic region by adding TECAR to the MT intervention.

Address parsing is a crucial task in natural language processing, particularly for Chinese addresses. The complex structure and semantic features of Chinese addresses present challenges due to their inherent ambiguity. Additionally, different task scenarios require varying levels of granularity in address components, further complicating the parsing process. To address these challenges and adapt to low-resource environments, we propose CapICL, a novel Chinese address parsing model based on the In-Context Learning (ICL) framework. CapICL leverages a sequence generator, regular expression matching, BERT semantic similarity computation, and GPT modeling to enhance parsing accuracy by incorporating contextual information. We construct the sequence generator using a small annotated dataset, capturing distribution patterns and boundary features of address types to model address structure and semantics, mitigating interference from unnecessary variations. We introduce the REB-KNN algorithm, which selects similar samples for ICL-based parsing using regular expression matching and BERT semantic similarity computation. The selected samples, raw text, and explanatory text are combined to form prompts, and inputted into the GPT model for prediction and address parsing. Experimental results demonstrate significant achievements of CapICL in low-resource environments, reducing dependency on annotated data and computational resources. Our model's effectiveness, adaptability, and broad application potential are validated, showcasing its positive impact in natural language processing and geographical information systems.

Nowadays, energy decarbonization due to the integration of renewable energy sources presents important challenges to overcome. The intermittent nature of photovoltaic systems reduces power quality by producing voltage variations and frequency deviations in electrical systems networks, especially, in weak and isolated distribution systems in developing countries. This paper presents a power smoothing method improving the low pass filter and moving average for grid-connected photovoltaic system, the novel method includes state-of-charge monitoring control of the supercapacitors energy storage system to reduce the fluctuations of photovoltaic power at the point of common coupling. A case study for a microgrid in a high-altitude city in Ecuador is presented with exhaustive laboratory tests using real data. The ultimate goal of this research is to improve energy power quality in electrical distribution systems to cope with the growth of renewable penetration.

Currently, the district heating (DH) in Poland is facing many challenges. The business model used hitherto was very simple—in most cities, heating plants produced heat, and centralized heating systems supplied the "product" at a price approved annually by the president of the Energy Regulatory Office (URE). However, recent years have brought significant changes on the market. EU regulations force the elimination of old coal-fired plants that were still built in the Polish People's Republic (PRL), moreover, high prices of CO2 emission allowances aggravate the financial situation of companies. In addition, in the heating sector, the trend observed in the power sector is becoming increasingly visible—limiting the role of large sources in favor of energy generated locally, closer to the customer. One of the biggest challenges is achieving the targets set by the EU for the share of renewable energy sources (RES) in the heating sector. The war in Ukraine and problems with the supply of coal and gas are an additional impulse to turn to RES. Thus, the development of sustainable and innovative solutions for energy production and supply at the level of urban networks is currently one of the main technical challenges. The purpose of the paper is to present the current situation and perspectives of development of district heating systems in Poland with a view to the status of district heating in the world, and some deeper insight into European conditions. The review presents energy sources with particular emphasis on renewable energy sources (RES) and their cogeneration for heat production. The examples of existing heating network solutions using renewable energy sources, based on the selected published case studies, are also discussed.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

Spatial variation of indoor and outdoor PM2.5 within three states for a 5-year period is studied using regulatory and low-cost PurpleAir monitors. Most of these data were collected in an earlier study1 investigating the relative contribution of indoor-generated and outdoor-infiltrated particles to indoor exposures. About 260 regulatory monitors and ~10,000 outdoor and ~4,000 indoor PurpleAir monitors are included. Daily mean PM2.5 concentrations, correlations, and coefficients of divergence (COD) are calculated for pairs of monitors at distances ranging from 0 (collocated) to 200 km. We use a transparent and reproducible open algorithm that avoids use of the proprietary algorithms provided by the manufacturer of the sensors in PurpleAir PA-I and PA-II monitors. The algorithm is available on the PurpleAir API website under the name “PM2.5_alt”. This algorithm is validated using several hundred pairs of regulatory and PurpleAir monitors separated by up to 0.5 km. The PM2.5 spatial variation outdoors is homogeneous with high correlations to at least 10 km, as shown by the COD index under 0.2. There is also a steady improvement in outdoor PM2.5 concentrations with increasing distance from the regulatory monitors. The spatial variation of indoor PM2.5 indoors is not homogeneous even at distances <100 m. We document substantial differences between Federal Reference Methods (FRM) and Federal Equivalent Methods (FEM).

Background: Low T3 syndrome occurs frequently in patients with sepsis. Type 3 deiodinase (Dio3) is present in immune cells but there is no description of its presence in this patients. Here we aimed to determine the prognostic impact of thyroid hormones levels (TH) measured on ICU admission on mortality and on evolution to chronic critical illness (CCI) and the presence of D3 in white cells. Methods: Prospective cohort study with a follow-up for 28 days or deceased. Results: Low T3 levels at admission were present in 86.5% of the patients. Dio3 was 55% induced in immune cells. The cut-off value of 60 pg/mL for T3 displayed a sensitivity and specificity of 81% and 64% for predicting death, odds ratio of 4.89. Lower T3 yielded an area under the receiver operating characteristic curve of 0.76 and 0.75 for mortality and evolution to CCI, respectively, thus displaying better performance than commonly used prognostic scores. Conclusions: We advance in the pathophysiology of low T3 showing induced D3 in immune cells during sepsis. Low T3 levels independently predicted a progression to CCI and mortality within 28 days in sepsis and septic shock.

Background: The thoracolumbar fascia (TLF) is thought to play a role in the development of LBP, but it is not yet clear which factor of TLF changes is a cause and which is an effect. Therefore, some studies used the cross-correlation function (CCR) to reveal time-dependent relationships between biomechanical and neuromotor factors. Methods: Ten patients with acute low back pain (aLBP) were matched to healthy controls. Simultaneous recording of surface electromyography (sEMG) of the erector spinae muscle (ES) and dynamic ultrasound (US) images of TLF deformation were performed during trunk extension. CCR functions and Granger causality were used to describe the relationship between the two measures. Results: CCR time lags were significant higher in the aLBP group (p = 0.04). Granger causality (GC) showed a direct effect of TLF deformation on ES activation only in the aLBP group (p &lt; 0.03). Conclusions: The results suggest that in aLBP, ES activity is significantly affected by TLF, whereas this relation-ship is completely random in healthy subjects studied with CCR and GC comparisons of dynamic US imaging and sEMG data signals. Fascia-related disturbances in neuromotor control, particularly due to altered muscle spindle functions, are suspected as a possible mechanism behind this.

The C/N ratio is an extremely important parameter in the composting process, which is directly responsible for the growth of microorganisms. A low C/N ratio contributes to higher emissions of greenhouse gases and odorous substances, such as ammonia (NH3), which is formed by nitrogen mineralization. Due to the highly toxic effects of ammonia, it is a particularly unwanted by-product that can disrupt the composting process because it poisons microorganisms and cause environmental issues. The activity of anammox bacteria, so far analyzed only in wastewater treatment processes, is a particularly efficient method of nitrogen removal, having an advantage over the conventional methods used previously. Our study proofs the presence of anammox bacteria during composting, what gives an opportunity to improve the process and reduce its impact on atmospheric pollution. Despite the aerobic nature of this process, the composted mass of waste presents conditions conducive to the development of these ammonia oxidizing bacteria, as well as other strains of microorganisms cooperating with them. This makes it possible to compost at a low C/N ratio; in addition, there is no need for additional energy supply through aeration, as the processes carried out by anammox bacteria do not require oxygen.

Global use of single-use non-biodegradable plastics, like bottles made of polyethylene tereph-thalate (PET), have contributed to catastrophic levels of plastic pollution. Fortunately, microbi-al communities are adapting to assimilate plastic waste. Previously, our work showed a full consortium of five bacteria capable of synergistically degrading PET. Using omics approaches we identified key genes implicated in PET degradation within the consortium’s pangenome and transcriptome. This analysis led to the discovery of a novel PETase, EstB, discovered to hydrolyze oligomer BHET, and polymer PET. Besides genes implicated in PET degradation, many other biodegradation genes were discovered. Over 200 plastic and plasticizer degrada-tion related genes were discovered through the Plastic Microbial Biodegradation Database (PMBD). Diverse carbon source utilization was observed by a microbial community-based as-say, which paired with an abundant number of plastic and plasticizer degrading enzymes in-dicates a promising possibility for mixed plastic degradation. Using RNAseq differential analysis, several genes were predicted to be involved in PET degradation including aldehyde dehydrogenases and several classes of hydrolases. Active transcription of PET monomer me-tabolism was also observed, including the generation of polyhydroxyalkanoate (PHA) bi-opolymers. These results present an exciting opportunity for the bio-recycling of mixed plastic waste with upcycling potential.

Satellite communication is expected to play a vital role in realizing Internet of Remote Things (IoRT) applications. This article considers an intelligent reflecting surface (IRS)-assisted downlink low Earth orbit (LEO) satellite communication network, where IRS provides additional reflective links to enhance the intended signal power. We aim to maximize the sum-rate of all the terrestrial users by jointly optimizing the satellite’s precoding matrix and IRS’s phase shifts. However, it is difficult to directly acquire the instantaneous channel state information (CSI) and optimal phase shifts of IRS due to the high mobility of LEO and the passive nature of reflective elements. Moreover, most conventional solution algorithms suffer from high computational complexity and are not applicable to these dynamic scenarios. A robust beamforming design based on graph attention networks (RBF-GAT) is proposed to establish a direct mapping from the received pilots and dynamic network topology to the satellite and IRS’s beamforming, which is trained offline using the unsupervised learning approach. The simulation results corroborate that the proposed RBF-GAT can achieve approximate performance compared to the upper bound with low complexity.

Objectives: Low and Middle Income Countries (LMICs) are experiencing a fast-paced epidemiological rise in clusters of non-communicable diseases (NCDs) such as diabetes and cardiovascular disease, forming an imminent rise in multimorbidity (MMD). However, preventing MMD has received little attention in LMICs, especially in Sub-Saharan African Countries. Design: Narrative review which scoped the most recent evidence in LMICs about MMD determinants and appropriated them for potential MMD prevention strategies. Methods: MMD in LMICs is affected by several determinants including increased age, female gender, environment, lower socio-economic status, obesity, and lifestyle behavious, especially poor nutrition and physical inactivity. Results: MMD public health interventions in LMICs, especially Sub-Saharan are currently impeded by local and regional economic disparity, underdeveloped healthcare systems, and concurrent prevalence of communicable diseases. However, lifestyle interventions that are targeted towards preventing highly prevalent MMD clusters, especially hypertension, diabetes and cardiovascular disease, can provide an early prevention of MMD, especially within Sub-Saharan African countries with emerging economies and socio-economic disparity. Conclusion: Future public health initiatives should consider targeted lifestyle interventions and appropriate policies and guidelines in preventing MMD in LMICs.

This study presents three forms of interdisciplinary expertise in the healthcare design context to approach a particular multifaceted problem around the current healthcare for older adult patients with chronic low-back pain (LBP). Using an interdisciplinary co-design framework, first, our design approach performs the role of an initiator to define the problem by exploring the current context of healthcare. Second, it facilitates the experiences of experts and patients to reach the roots of the problem by functioning as a mediator. Third, our approach fulfills the primary role of healthcare design in producing new meanings considering the principles of patient-centeredness. These roles significantly contributed to the design of healthcare innovations. Our framework transformed the distributed disciplinary knowledge developed while tackling the multifaceted problem into new forms of expertise for collaboration in healthcare innovation.

Tomato is exposure to diverse abiotic stresses. Cold stress is one of harsh environmental stresses and abnormal low temperature affects tomato growth and development including physio- logical disorders, flower drops, and abnormal fruit morphology, causing the decrease of tomato yield and a fruit quality. It is important to identify low temperature-(LT) tolerant tomato (Solanum lycopersicum L.) cultivars relying on different fruit types. This study focused on analyzing physiological traits of 35 tomato accessions with three different fruit types (cherry, medium, and large sizes) under night temperature set-points of 15°C for normal temperature (NT) and 10°C for LT, respectively. Plant heights (PH) of most tomato accessions in LT were remarkably decreased compared to those in NT. The growth of leaf length (LL) and leaf width (LW) was reduced depending on the genotypes under LT. In addition, the number of fruits (NFR), fruit set (FS), fruit yield (FY), and marketable yield (MY) were negatively affected in LT. The variation was further investigated by the correlation analysis, the principal component (PCA), and the cluster analysis. Interestingly, positive correlations between different vegetative and reproductive traits were uncovered. Multivariate analysis including the PCA and hierarchical clustering classified LT-treated 35 tomato accessions into four major groups. The identified accessions were associated with vegetative and reproductive parameters on positive directions and might be utilized for breeding programs on selecting LT-tolerant cultivars.

The current study investigated whether a domain-specific intervention targeting maths and executive functions of primary school children with a Roma background would be effective in improving their scholastic performance and executive functioning. In total, 122 students attending Grade 4 of elementary school took part in the project. The study concerned a pretest-intervention-training experimental design with three conditions: the experimental condition, an active and a passive control group. The results suggested that both maths performance and executive functions improved over time, with no significant differences between the three conditions. An additional correlational analysis indicated that pretest performance was not related to posttest performance for the children in the experimental and active control group.

Urban cities in sub-Saharan Africa (SSA) are faced with ambient air pollution. This is an important public health problem with models and limited monitoring data indicating high concentrations of pollutants such as fine particulate matter (PM_2.5). Going through most global air quality index maps, however, information about ambient pollution from SSA is scarce. We evaluated the feasibility and practicality of longitudinal measurements of ambient PM_2.5 using low-cost air quality sensors (Purple Air-II-SD) across thirteen locations in seven countries in SSA. Devices were used to gather data over a 30-day period with the aim of assessing the efficiency of its data recovery rate and identifying challenges experienced by users in each location. The median data recovery rate was 94% (range: 72% to 100%). The mean 24-hour concentration measured across all sites was 38 µg/m³ with the highest PM_2.5 period average concentration of 91 µg/m³ measured in Kampala, Uganda and lowest concentrations of 15 µg/m³ measured in Faraja, The Gambia. Kampala-Uganda and Nnewi-Nigeria recorded the longest periods with concentrations>250µg/m³. Power outages, SD memory card issues, internet connectivity problems and device safety concerns were important challenges experienced when using Purple Air-II-SD sensors. Despite some operational challenges, this study demonstrated that it is reasonably practicable and feasible to establish a network of low-cost devices to provide data on local PM_2.5 concentrations in SSA countries. Such data are crucially needed to raise public-, societal and policymaker awareness about air pollution across SSA.

Mass timber products, together with careful forestry management, could help decarbonize the construction industry. These products must be long-lasting, to safely store atmospheric carbon for decades or centuries, and multi-functional, to displace materials and equipment that are emissions-intensive. This paper shows how to optimize mass timber panels as heat-exchangers, suggesting how to eliminate insulation while simplifying HVAC systems. Test panels measured the heat-exchange in steady and transient conditions, when the ventilation was driven by a fan or by thermal buoyancy. The total heatexchange was predicted accurately by theory in all cases. Further investigation is needed to understand the possible heat-recovery effects at the exterior surface.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close to the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li embedded into various matrices. The one-dimensional lattice built of the identical metallic micro-elements m_eff connected by ideal springs k_1 representing various media such as polydimethylsiloxane and soda-lime glass is treated. The optical and acoustical branches of longitudinal modes propagating through the lattice are elucidated for various ratios ω_1/ω_p . The 1D lattice built of the thin metallic wires giving rise to the low frequency plasmons is treated. The possibility of the anti-resonant propagation, strengthening the effect of the negative mass occurring under  = p = 1 is addressed.

Exploiting the linguistic knowledge of the source language for neural machine translation (NMT) has recently achieved impressive performance on many large-scale language pairs. However, since the Turkish→English machine translation task is low-resource and the source-side Turkish is morphologically-rich, there are limited resources of bilingual corpora and linguistic information available to further improve the NMT performance. Focusing on the above issues, we propose a multi-source NMT approach that models the word feature in parallel to external linguistic features by using two separate encoders to explicitly incorporate linguistic knowledge into the NMT model. We extend the word embedding layer of the knowledge-based encoder to accommodate for each word’s linguistic annotations in the context. Moreover, we share all parameters across encoders to enhance the representation ability of the NMT model on the source language. Experimental results show that our proposed approach achieves substantial improvements of up to 2.4 and 1.1 BLEU scores in Turkish→English and English→Turkish machine translation tasks, respectively, which points to a promising way to utilize the source-side linguistic knowledge for the low-resource NMT.

In this study, four kinds of animal bone marrow powders were extracted with n-hexane using the Soxhlet extraction method. Polyunsaturated fatty acids were enriched by urea inclusion and low temperature crystallization method, then were further evaluated antioxidant and antibacterial activities. These results showed that the oil composition of the n-hexane extracts of four kinds of animal bone marrow primarily consisted of palmitic acid (18.57–31.01%), stearic acid (3.6–20.95%), and oleic acid (40.22–58.69%). The ratios of saturated fatty acids (SFA)/unsaturated fatty acids (UFA) were 1/1.417, 1/1.327, 1/2.140, and 1.285/1 for sheep, bovine, horse, and camel bone marrow oil, respectively. The SFA/UFA ratios determined by the urea inclusion method were 1/1.518, 1/1.390, 1/2.037, and 1.216/1, respectively. The SFA/UFA ratios according to the low temperature crystallization method with acetone were 1/1.920, 1/2.141, 1/2.360, and 1/1.157 for sheep, bovine, horse, and camel bone marrow oil, respectively. These enrichment methods effected the concentrations of UFAs from the camel bone marrow oil. Among the methods, the low temperature crystallization method effectively enriched the UFAs. All four bone marrow oils exhibited strong antioxidant and antimicrobial activities. The horse bone marrow oil showed the strongest antioxidant activity. Both antioxidant and antimicrobial activity improved after enrichment of the UFAs. These results lay a theoretical basis for application bone marrow oil resources in food and medicine.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

The paper presents dynamic and transient behaviour of the Doubly Fed Induction Generator (DFIG) in the wind farms. When Voltage sag or any faults occurs in the network, the variables in the doubly Fed Induction Generators are varying severely. If the voltage sag occurs, Active and Reactive power that generated by the DFIG will decrease and will increase respectively, The DC voltage link will be bigger, and the rotor current will increase. The DFIG in the wind farms uses Proportional Integral controller for controlling of electronic devices (Rotor Side Converter and Grid Side Converter). Even though the model of Doubly Fed Induction Generators and electronic device in the paper are linear, The Proportional Integral controllers cannot protect and control the variables. So, the power electronic converters and the DC-link can damage due to over voltages and over currents. Doubly Fed Induction Generator in the wind farm is simulated in MATLAB software. The results of the simulation present over voltage and over current in the DC-link and in the rotor of the Doubly Fed Induction Generator. In addition, it will explore the effect of Proportional Integral controller in Doubly Fed Induction Generator when three-phase short circuit fault occurs

Electric Vehicles (EVs) are increasing the interdependence of transportation policies and the electricity market. EMMEV (Electricity Market Model with Electric Vehicles) is an experimental agent-based model that analyses how carbon reduction policy in transportation may increase number of Electric Vehicles and how does that would influence on the electricity price. Agents are ESCOs (Energy Service Providers) which can distribute fuels and their objective is to maximize their profit. In this paper, EMMEV is used to analyze the impacts of the LCFS (Low Carbon Fuel Standard), a performance-based policy instrument, on electricity prices and EV sales. The agents in EMMEV/regulated parties in LCFS should meet a certain CI (Carbon Intensity) target for their distributed fuel. In case, they cannot meet the target, they should buy credit to compensate for their shortfall and if they exceed, they can sell their excess. The results, considering the assumptions and limitations of the model, show that the banking strategy of the agents contributing in the LCFS might have negative impact on penetration of EVs, unless there is a regular Credit Clearance to trade credits. It is also shown that the electricity price as result of implementing the LCFS and increasing number of EVs has increased between 2–3 percent depending on banking strategy.

Supply chain management requires regular updates of the location of assets, which can be enabled by low power wide area networks, such as Sigfox. While it is useful to localize a device simply by its communication signals, this is very difficult to do with Sigfox because of wide area and ultra narrowband nature. On the other hand, installing a satellite localization element on the device greatly increases its power consumption. We investigated using information about nearby Wi-Fi access points as a way to localize the asset over the Sigfox network, so without connecting to those Wi-Fi networks. This paper reports the location error that can be achieved by this type of outdoor localization. By using a combination of two databases, we could localize the device on all 36 test locations with a median location error of 39 m. This shows that the localization accuracy of this method is promising enough to warrant further study, most specifically the minimal power consumption.

Preterm infants have increased body adiposity at term equivalent age and risk for adverse metabolic outcomes. The aim of the study was to define how nutrient intake may impact body composition (BC) of very low birth weight infants fed with early progressive enteral feeding and standard fortification. Eighty-six infants with

In the context of carbon neutrality and carbon peaking, in order to achieve low carbon emissions and promote the efficient utilization of wind energy, hydrogen energy as an important energy carrier is proposed to mix hydrogen and natural gas to form hydrogen enriched compressed natu-ral gas (HCNG). It is also injected into the natural gas pipeline network to realize the transmission and utilization of hydrogen energy. At the same time, the participation of demand response is considered, the load peak and trough period is adjusted, and large-scale consumption of renewa-ble energy and the reduction of carbon emissions are realized. First of all, a fine model of hydro-gen production and hydrogen use equipment is established to analyze the impact of adding hy-drogen mixing on the economy and low-carbon of the system. With green certificates and demand response, the utilization rate of hydrogen energy is improved to further explore the energy utiliza-tion rate and emission reduction capacity of the system. Secondly, on the basis of modeling, the optimal scheduling strategy is proposed with the sum of energy purchase cost, equipment opera-tion cost, carbon emission cost, wind curtailment cost and green certificate income as the lowest objective function. Considering the constraints such as hydrogen blending ratio and flexible load ratio of the pipeline network, a low-carbon economic scheduling model of hydrogen mixed natu-ral gas was established. The model was linearized and solved by using MATLAB and CPLEX solver. By comparing different scenarios, the superiority of the model and the effectiveness of the strategy are verified.

We propose a new methodology for long-time biopotential recording based on MEMS multisensor integrated platform featuring a commercial electrostatic charge transfer sensor. That family of sensors was originally intended for presence tracking in automotive, so the existing setup has been engineered for the acquisition of electrocardiogram, electroencephalogram, electrooculogram and electromyography, designing a dedicated front-end and writing a proper firmware for the specific application. Systematic tests on controls and nocturnal acquisitions from patients in domestic environment will be discussed in detail. The excellent results candidate this technology to provide a low power, unexplored solution to biopotentials acquisition. The technology breakthrough is in that it enables adding this type of functionality to existing MEMS boards at near-zero additional power consumption. For these reasons, they open to additional possibilities for wearable sensing and strengthen the role of MEMS technology in medical wearable applications for long time synchronous acquisition of a wide range of signals.

To date, radiation adaptation response has been reported as a low-dose related phenomenon and has been associated with radiation hormesis. Well-known cancers are caused by non-radiation active reactants, in addition to radiation. A model of suppression for radiation-specific cancers was previously reported, but the model did not target radiation-nonspecific cancers. In this paper, we describe kinetic models of radiation-induced suppressors for general radiation non-specific cancers, estimating the dose that induces the maximum hormesis effect while satisfying the condition that the risk is approximately proportional to dose above 100 mSv. It was found that the radiation hormesis effect is maximal at about 20 mSv when the rate constant for generation is the same as the rate constant for decomposition. When the two rate constants are different, the dose at which the radiation hormesis effect is maximized depends on both rate constants, but the dose increases as the two rate constants approach each other, reaching a maximum of about 20 mSv. This conclusion may lead to the discovery of unknown cancer suppressors at low doses and the development of cancer suppression methods in the future.

This study leverages the relationships between the Great Plains low-level jet (GP-LLJ) and the circumglobal teleconnection (CGT) to enhance the 30-day rainfall forecast skill in the Northern Great Plains (NGP). The assessment of 30-day simulated precipitation using the Climate Forecast System (CFS) is contrasted with the North American Regional Reanalysis, searching for sources of precipitation predictability associated with extended wet and drought events. We analyze the 30-day sources of precipitation predictability using (1) the characterization of dominant statistical modes of variability of 900-mb winds associated with the GP-LLJ, (2) the large-scale atmospheric patterns based on 200-mb geopotential height (HGT), and (3) the use of GP-LLJ and CGT conditional probability distributions using a continuous correlation threshold approach to identify when and where the forecast of NGP precipitation occurs. Two factors contributing to the predictability of precipitation in the NGP are documented. We found that multi-scale geospatial interactions occur at the daily and sub-seasonal time windows. The CFS reforecast suggests that the ability to forecast sub-seasonal precipitation increases in response to the enhanced simulation of the GP-LLJ and CGT. Finally, the multi-dimensional analysis of covariance reveals that high-precipitation forecasting skill is associated with a better prognostic of GP-LLJ and CGT.

For two-dimensional forward-looking sonar imaging, high sidelobes significantly degrade the quality of sonar images. The cosine window function weighting method is often applied to suppress the sidelobe levels in the angular and range dimensions at the expense of the main lobe resolutions. Therefore, the improved spatially variant apodization imaging method for forward-looking sonar is proposed to reduce the sidelobes without degrading the main lobe resolution in angular-range dimensions. The proposed method is a nonlinear post-processing operation in which the raw complex-valued sonar image produced by a conventional beamformer and matched filter is weighted by a spatially variant coefficient. To enhance the robustness of the spatially variant apodization approach, the array magnitude and phase errors are calibrated to prevent beam sidelobe heightening from occurring prior to beamforming operations. The analyzed results of numerical simulations and a lake experiment demonstrate that the proposed method can greatly reduce the sidelobes to approximately -40 dB, while the main lobe width remains unchanged. Moreover, this method has an extremely simple computational process.

The improvement of agricultural low-carbon efficiency is an important path to promote the realization of the "double carbon" goal in the Yellow River Basin. In the context of rapid urbanization development, it is of great significance to explore whether the promotion of urbanization will affect the agricultural low-carbon efficiency. Based on the panel data of 75 cities in the Yellow River Basin from 2000 to 2020, this paper uses super-DEA model, three-dimensional kernel density model and Markov chain model to measure and analyze the spatio-temporal evolution of agricultural low-carbon efficiency in the Yellow River Basin, on this basis, the panel Tobit model is used to analyze the relationship between urbanization and low-carbon efficiency in agriculture. The results show that: (1) The level of agricultural low-carbon efficiency in the Yellow River Basin is low and has not reached the effective state, showing a slow downward trend in general, among which, the agricultural low-carbon efficiency in the lower reaches is higher than that in the middle reaches, and the upper reaches is the lowest. (2) The agricultural low-carbon efficiency in the Yellow River Basin has a negative trend of transferring to the low level on the whole, and tends to maintain the original state level, and it is difficult to realize the leapfrog transfer between states. Agricultural low-carbon efficiency has obvious spatial spillover effect and "club convergence" phenomenon, high efficiency area has a positive driving effect on the neighborhood area, while low efficiency area has a negative impact on the neighborhood area. (3) The level of urbanization has a significant positive impact on the low-carbon efficiency of agriculture in the upper, middle and lower reaches of the Yellow River Basin, which plays an important role in promoting the green development of agriculture. Finally, based on the above research conclusions, relevant policy recommendations were put forward, in order to provide references for promoting the improvement of low-carbon agricultural efficiency and promoting high-quality agricultural development in the Yellow River Basin.