The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Here we report the preparation and characterization of a novel biomimetic toothpaste containing morphogenetically active amorphous polyphosphate (polyP) microparticles enriched with retinyl acetate (“a-polyP/RA-MP”). The spherical microparticles (average size, 550±120 nm), prepared by co-precipitating sodium-polyP with calcium chloride and supplemented with retinyl acetate, were incorporated into a basis toothpaste at a final concentration of 1% or 10%. The paste containing “a-polyP/RA-MP” significantly increased the growth of human mesenchymal stem cells (MSC), compared to a commercial toothpaste which acts rather inhibitory and the paste without polyP and retinyl acetate. qRT-PCR experiments revealed that the retinoid causes an induction of the expression of the MSC marker genes for osteoblast differentiation encoding collagen type I and alkaline phosphatase. On the other hand, the polyP ingredient, supplied as Zn-polyP microparticles (“Zn-a-polyP-MP”) strongly inhibited the growth of the cariogenic bacterium Streptococcus mutans. We demonstrate that the amorphous polyP-containing toothpaste, enriched with retinyl acetate, efficiently repairs both cracks/fissures and carious lesions in the tooth enamel, and reseals dentinal tubules, already after a 5 d treatment (brushing) of teeth twice daily for 5 min as examined by SEM and quantitative EDX analysis. The stability of the occlusion of dentin cracks even turned out to resist against short high power sonication treatment. Our results demonstrate that the novel toothpaste prepared here, containing amorphous polyP and retinyl acetate, is particularly suitable for prevention/repair of (cariogenic) damages of tooth enamel/dentin and for treatment of dental hypersensitivity.

Background and objectives: The correlation of cardiac troponin I with early in-hospital outcomes in acute myocardial infarction is not well established. This study aims to assess the role of troponin I in predicting in-hospital outcomes and early left ventricular systolic dysfunction in patients with ST-segment elevation myocardial infarction (STEMI). Patients and methods: In a prospective study, 116 patients (74males and 42 females), with STEMI who had been admitted to the Coronary CareUnit from March 2015 to September 2015 were enrolled. Patients were divided according to the level of troponin I on admission into 3 groups (low, medium and high elevation). Results: The mean age (+ SD) of the patients was 60+11.4 years. The troponin level of 66.2% of males was high compared with 52.4% of females (p=0.002). The incidence of acute pulmonary edema (21.1%), cardiogenic shock (7%) and early left ventricular systolic dysfunction (49.3%) was significantly higher among patients with high troponin level compared with (0%, 0% and 16%, respectively) among patients with low troponin level. All deaths and cardiac arrest were of high troponin level. Conclusions: High admission troponin I in STEMI permits early identification of patients at increased risk of major cardiac complications and death.

A vehicle boom barrier gate system is one of the recently developed technologies operating at the entrances to the restricted areas. This paper aims to design and control of vehicle’s boom barrier gate system using robust augmentation technique. H 2 optimal and H infinity synthesis controllers are used to improve the performance of the system. The open loop response analysis of the vehicle boom barrier gate system shows that the input of the system need to be improved. Comparison of the vehicle boom barrier gate system with H2 optimal and H infinity synthesis controllers have been done to track a set point desired angular position using a step and operational open and close input signals and a promising results have been observed.

Fourteen (14) rack-mounted polycrystalline modules installed on the concrete roof of the solar energy applications laboratory at the Kwame Nkrumah University of Science and Technology (KNUST) in Ghana, a hot humid environment were assessed after 19 years of continuous outdoor expodure. The physical state of the modules was documented using a visual inspection checklist. They were further assessed by current-voltage (I-V) characterization and thermal imaging. The modules were found to be in good physical state, except some bubbles on front side and minor discolouration/corrosion at edge of the cells. Compared with reference values, the performance decline of the modules observed over the exposure period was: nominal power (P_nom), 21% to 35%; short circuit current (I_sc), 5.8% to 11.7%; open circuit voltage (V_oc) 3.6% to 5.6% and 11.9% to 25.7% for fill factor (FF). It is hoped that this study will provide some helpful information to project developers, manufacturers and the research community on the long-term performance of PV modules in Ghana.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

Trajectory Optimization (TO) is the sequence of processes that are considered in order to produce the best path that mends the overall performance or reduces the consumption of the resources where the restriction system remains maintained. In this survey, an inclusive review of the latest advancements in modeling and optimization of trajectory generation in robotic applications will be discussed broadly. In recent times, numerous studies have employed optimal control techniques involving direct and indirect methods in order to convert the authentic Trajectory Optimization problem into a constrained parameter optimization problem. Moreover, a huge variety of optimization algorithms such as Genetic Algorithms (GA), Simulated Annealing (SA), Sequential Quadratic Programming (SQP), and Particle Swarm Optimization (PSO) are used aiming to find the optimal solutions for trajectory planning. It is observable that, minimizing the jerk, energy consumption, and execution time among the most widely used design objectives, on the other hand, the robot’s joints configurations and the motor torques are the most used design variables. This paper aims to review the fundamental techniques and their coincident robotic applications in the field of trajectory optimization aiming to afford some steering for related researchers.

This paper presents a study on optimization of Overcurrent relay (OCR) coordination protection scheme for Sustainable Standalone Hydrokinetic Renewable Energy (SHRE) distribution network at Batang Rajang river, located at Kapit Sarawak, Malaysia by turning river stream into power generation source. The purpose of the project is to develop rural electrification system for native long houses along the river. The research study is tested on a DigSILENT develop model of the SHRE distribution network and in accordance with all respectively unique parameters and relevant standards. Since this is a new standalone distribution system, an efficient and properly coordinated overcurrent protection system must be provided. Improper and miscoordination among OCRs result in maloperation of the protection system that can lead to false tripping and an unnecessary outage and power system instability. Thus, the objective of this work is to employ Genetic Algorithm (GA) technique in Matlab/Simulink for optimal overcurrent coordination and settings among all OCRs in the proposed distribution network in order to improve the speed of OCR tripping operation. The GA is used because the project is fast track and requiring the simplest method available. In this strategy, time dial setting (TDS) is optimized by using plug setting multiplier (PSM) as the constraint. The obtained results show a significant improvement of the relay operating time of 36.01% faster than that of conventional numerical technique during fault occurrence. Thus, an efficient and reliable overcurrent protection scheme has been achieved for the SHRE distribution network.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

This paper proposes a Mixed Integer Conic Programming (MICP) model for community microgrids considering the network operational constraints and building thermal dynamics. The proposed multi-objective optimization model optimizes not only the operating cost, including fuel cost, purchasing cost, battery degradation cost, voluntary load shedding cost and the cost associated with customer discomfort due to room temperature deviation from the set point, but also several performance indices, including voltage deviation, network power loss and power factor at the Point of Common Coupling (PCC). In particular, the detailed thermal dynamic model of buildings is integrated into the distribution optimal power flow (D-OPF) model for the optimal operation. The heating, ventilation and air-conditioning (HVAC) systems can be scheduled intelligently to reduce the electricity cost while maintaining the indoor temperature in the comfort range set by customers. Numerical simulation results show the effectiveness of the proposed model and significant savings in electricity cost with network operational constraints satisfied.

Near-infrared spectroscopy (NIRS) was implemented to monitor the moisture content of broadleaf litters. Partial least-squares regression (PLSR) models, incorporating optimal wavelength selection techniques, have been proposed to better predict the litter moisture of forest floor. Three broadleaf litters were used to sample the reflection spectra corresponding the different degrees of litter moisture. Maximum normalization preprocessing technique was successfully applied to remove unwanted noise from the reflectance spectra of litters. Four variable selection methods were also employed to extract the optimal subset of measured spectra for establishing the best prediction model. The results showed that the PLSR model with the peak of beta coefficients method was the best predictor among all candidate models. The proposed NIRS procedure is thought to be a suitable technique for on-the-spot evaluation of litter moisture.

A gold(I) complex with a triphenylphosphine and a monodentate N,N-dimethyldithiocarbamate ligand was synthesized and characterized by Raman spectroscopy and single crystal X-ray diffraction. DFT calculations (Gaussian 09, PBE1PBE/Lanl2dz) were undertaken for a single complex in the gas-phase. The DFT-optimized structure is in good agreement with the crystal structure and the DFT-calculated Raman spectrum also is in excellent agreement with the experimental spectrum. Assignments of the Raman peaks are based on these DFT calculations. Frontier molecular orbitals were calculated and their nature is discussed.

the intermittency and variability of these permeated Distributed Generators (DGs) could critically cause many security and economy risks to distribution systems. This paper applied a certain mathematical distribution to imitate the output variability and uncertainty of DGs. And then, four risk indices EENS, PLC, EFLC and SI were established to reflect the system risk level of distribution system. For the certain mathematical distribution of the DGs' output power, a developed PEM (point estimate method)-based method was proposed to calculate these four system risk indices. In this developed PEM-based method, enumeration method was used to list the states of distribution systems, an improved PEM was presented to deal with the uncertainties of DGs and the value of load curtailment in distribution systems was calculated by an optimal power flow algorithm. Finally, the effectiveness and advantages of this proposed PEM-based method for distribution system assessment were verified by the tests of a modified IEEE 30-bus system. Simulation results have shown that this proposed PEM-based method has a high computational accuracy and highly reduced computational costs compared with other risk assessment methods and is very effective for risk assessments.

Although most cases of COVID-19 are paucisymptomatic, severe disease is characterized by immune dysregulation, with a decreased type I interferon response, increased inflammatory indicators, surging IL-6, IL-10 and TNFα suggestive of cytokine storm, progressive lymphopenia, and abnormal blood clotting. Factors determining susceptibility to severe disease are poorly understood, although mortality correlates with increasing age and co-morbidities including diabetes and cardiovascular disease (CVD). Pyridoxal 5'-phosphate (PLP) tends to be insufficient in populations particularly vulnerable to COVID-19, including the elderly, the institutionalized, and people with diabetes and CVD, and PLP becomes further depleted during infection and inflammation. In turn, low PLP results in immune imbalance, as PLP is an essential cofactor in pathways regulating cytokine production, in particular type I interferons and IL-6, and in lymphocyte trafficking and endothelial integrity. Furthermore, normalizing PLP levels attenuates abnormalities in platelet aggregation and clot formation. Finally, PLP insufficiency induces excess secretion of renin and angiotensin, and hypertension. In inflammatory disease, pharmacological doses of PLP decrease circulating TNFα, IL-6 and D-dimer, and animal studies demonstrate that supplemental PLP shortens the duration and severity of viral pneumonia. Severe COVID-19 manifests as an imbalance in the immune response and the clotting system. Pharmacological PLP supplementation may therefore mitigate COVID-19 symptoms by alleviating both the immune suppression underlying viral spread and the pathological hypersecretion of inflammatory cytokines, as well as directly bolstering endothelial integrity and preventing hypercoagulability.

In the last few decades, the dynamics of tumor cells and their growths are presented via clinical, experimental, and theoretical approaches, which leads to the development of the new idea of multiple cancer therapies to control and reduce the death rate for earlier detection. In this paper, we discussed the dynamics of tumor cell growth and its treatment process. We analyzed some simple mathematical models and generalized the study to understand the growth of tumor cells. The main proposed model is a system of ordinary differential equations which combines interactions among natural killer cells, dendritic cells and cytotoxic CD8+ T cells. The model is solved numerically to explain how the tumor cells spread and become more dangerous as well as the treatment process of cancer. It is also studied that how the cell behaves in the presence of different therapy and drugs. The optimal control of chemotherapy has been discussed. It has also been explained how much the model is effective in reducing tumor cells over time. Finally, a couple of spatially distributed models are discussed for tumor cell growth.

A literature review was conducted to summarize the frequency of the D-allele of the angiotensin-converting enzyme-1 in all countries with available data. Using an ecological study design limited to high income countries, we found that the country-level frequency of the D-allele was associated with increased COVID-19 incidence and mortality.

Ovarian Cancer (OC) is a type of cancer that affects ovaries in women, and is difficult to detect at initial stage due to which it remains as one of the leading causes of cancer death. The ovarian cancer data generated from the Internet of Medical Things (IoMT) was used and a novel approach was proposed for distinguishing the ovarian cancer by utilizing Self Organizing Maps (SOM) and Optimal Recurrent Neural Networks (ORNN). SOM algorithm was utilized for better feature subset selection and was also utilized for separating profitable, understood and intriguing data from huge measures of medical data. In supervised learning techniques, the SOM-based feature selection seems to be a tougher challenge because of the absence of class labels that would guide the search for relevant information to the classifier model. The classification approach can identify ovarian cancer data as benign/malignant. The ovarian cancer detection process can be improved by optimizing the weights of RNN structure using Adaptive Harmony Search Optimization (AHSO). The proposed model in this study can be used to detect cancer at early stages with high accuracy and low Root Mean Square Error (RMSE).

The aim of this work is to introduce new ways to model the I-V characteristic of a PV cell or PV module using straight lines and Bézier curves. This is a complete novel approach, Bézier curves being previously used mainly for computer graphics. The I-V characteristic is divided in three sections, modeled with lines and a quadratic Bézier curve in the first case and with three cubic Bézier curves in the second case. The result proves to be accurate and relies on the fundamental points usually present in the PV cell datasheets: Voc (the open circuit voltage), Isc (the short circuit current), Vmp (the maximum power corresponding voltage) and Imp (the maximum power corresponding current) and the parasitic resistances Rsh0 (shunt resistance at Isc) and Rs0 (series resistance at Voc). The proposed algorithm completely defines all the implied control points and the error is analyzed. The temperature and irradiance influence is also analyzed. The model is also compared using the least squares fitting method. The final validation shows how to use Bézier cubic curves to accurately represent the I-V curves of an extensive range of PV cells and arrays.

Malaria and Pneumonia are leading causes of serious illness in children and adults worldwide with their death rate and prevalence on the rise. Such alarming statistics may retard the milestones so far achieved in meeting the Millennium Development Goals 4 and 6 whose targets are to improve child survival and reverse the high prevalence of diseases such as pneumonia and malaria respectively. Two sub-models of malaria-pneumonia co-infection namely malaria model and pneumonia model were considered first and then followed by the full malaria-pneumonia co-infection model. The malaria model, pneumonia model and co-infection model basic reproduction numbers denoted by R_m, R_p and R_mp respectively was obtained using the Next Generation Matrix method. The model disease free equilibrium’s local and global stability was analysed using Descartes’ Rule of signs and Comparison method. The bifurcation analysis for the malaria, pneumonia and co-infection models was studied using the Centre Manifold Theory. The sensitivity indices of the model basic reproduction numbers R_m, R_p and R_mp to the parameters in the models were calculated. Optimal control theory was applied using the Pontryagins’ Maximum Principle to investigate optimal strategies for controlling the spread of malaria, pneumonia and co-infection models using insecticide treated bed nets (u₁(t)) spraying of mosquitoes insecticides (u₂(t)), sanitation (u₃(t)), vaccination (u₄(t)), anti-malaria drugs (u₅(t)), anti-pneumonia drugs (u₆(t)), both anti-malaria drugs and anti-pneumonia drugs (u₇(t)) as the system time control variables. Numerical simulations using a set of parameter values were provided to validate the analytical results.

This review describes the positive effects of growth hormone on the cardiovascular system. We analyze why the vascular endothelium is a real internal secretion gland, whose inflammation is the first step for developing atherosclerosis, as well as the mechanisms by which GH acts on the vascular endothelium improving its dysfunction. We also report how GH acts on coronary arterial disease and heart failure, and on peripheral arterial disease inducing the generation of new collateral vessels able to bypass a major artery occlusion. We include some preliminary data from a trial in which GH or placebo is given to elder people suffering from critical limb ischemia, showing the effects of the hormone on plasma markers of inflammation, and stating that the administration of GH in short periods of time is safe and effective even in diabetic patients. We also analyze how Klotho may have strong relationships with GH, inducing, after being released from the damaged vascular endothelium, the pituitary secretion of GH to repair the damaged tissue. Lastly, we show how GH induces wound healing by increasing the blood flow to the ischemic tissue. In summary, we postulate that short-time GH administration is useful for treating cardiovascular diseases.

Bipedal locomotion remains one of the major open challenges of humanoid robotics. The common approaches are based on simple reduced model dynamics to generate walking trajectories, often neglecting the whole-body dynamics of the robots. As motions in nature are often considered as optimal with respect to certain criteria, in this work we present an optimal control based approach that allows us to generate optimized walking motions using a precise whole-body dynamic model of the robot, in contrast with the common approaches. The optimal control problem is formulated to minimize a set of desired objective functions with respect to physical constraints of the robot and contact constraints of the walking phases. We apply the method with combinations of different objective criteria to the model of a reduced version of the iCub humanoid robot of 15 internal DOF. The obtained trajectories are executed on the real robot and we carry out a discussion on the differences between the outcomes of this approach with the classic approaches.

The performance in terms of minimal Bayes’ error probability for detection of a high-dimensional random tensor is a fundamental under-studied difficult problem. In this work, we consider two Signal to Noise Ratio (SNR)-based detection problems of interest. Under the alternative hypothesis, i.e., for a non-zero SNR, the observed signals are either a noisy rank-R tensor admitting a Q-order Canonical Polyadic Decomposition (CPD) with large factors of size Nq  R, i.e, for 1  q  Q, where R, Nq ! ¥ with R1/q/Nq converge towards a finite constant or a noisy tensor admitting TucKer Decomposition (TKD) of multilinear (M1, . . . ,MQ)-rank with large factors of size Nq  Mq, i.e, for 1  q  Q, where Nq,Mq ! ¥ with Mq/Nq converge towards a finite constant. The detection of the random entries (coefficients) of the core tensor in the CPD/TKD is hard to study since the exact derivation of the error probability is mathematically intractable. To circumvent this technical difficulty, the Chernoff Upper Bound (CUB) for larger SNR and the Fisher information at low SNR are derived and studied, based on information geometry theory. The tightest CUB is reached for the value minimizing the error exponent, denoted by s?. In general, due to the asymmetry of the s-divergence, the Bhattacharyya Upper Bound (BUB) (that is, the Chernoff Information calculated at s? = 1/2) can not solve this problem effectively. As a consequence, we rely on a costly numerical optimization strategy to find s?. However, thanks to powerful random matrix theory tools, a simple analytical expression of s? is provided with respect to the Signal to Noise Ratio (SNR) in the two schemes considered. A main conclusion of this work is that the BUB is the tightest bound at low SNRs. This property is, however, no longer true for higher SNRs.

This paper proposes a game-theoretic framework for quantifying effects of strategic bidding behavior of load aggregators (LAs) on wholesale electricity market equilibrium. The independent system operator (ISO) employs double-sided auction design to settle transactions in the wholesale electricity market. Generating companies (GENCOs) and LAs submit their bids to the ISO in the economic model of supply function equilibrium. Under the smart grid paradigm, a LA participates in the electricity market on behalf of end-consumers to minimize their total payment for purchasing electricity. In this paper, bi-level programming (BLP) method is employed to determine optimal bidding strategy of self-interested market participants. In the upper level, the profit of intended market participant is maximized and in the lower level, the ISO clears the market via a bid-based security constrained economic dispatch (SCED). Also, competition of GENCOs and LAs is modeled as a non-cooperative game. To examine the effects of strategic bidding behavior of LAs on market equilibrium, the proposed model is applied to the IEEE 9-bus and the IEEE 30-bus test systems. According to numerical results, to allow the LAs to behave strategically along with the GENCOs makes the former better off and the latter worse off, while the net effect of this on total social welfare turns out to be case-contingent.

In this paper, modelling designing and simulation of a Ward Leonard layout system is done using robust control theory. In order to increase the performance of the Ward Leonard layout system with H infinity optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers are used. The open loop response of the Ward Leonard layout system shows that the system needs to be improved. Comparison of the Ward Leonard layout system with H∞ optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers to track a desired step speed input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed Ward Leonard layout system with H infinity optimal control synthesis controller in improving the percentage overshoot and the settling time.

The radial distribution networks are designed for unidirectional power flows and are passive in nature. However, with the penetration of Distributed Generation (DG), the power flow becomes bidirectional and the network becomes active. The integration of DGs into distribution network creates many issues with: system stability, protection coordination, power quality, islanding, proper placement and sizing etc. Among these issues, the two most significant are optimal sizing and placement of DGs and their protection coordination in utility network. The proper coordination of relays with high penetration of DGs placed at optimal location increases the availability and reliability of the network during abnormal operating conditions.This research addresses most of the available methods for efficient sizing and placement of DGs in distribution system (numerical, analytical and heuristic) as well as the developed protection coordination techniques for utility networks in the presence of DGs (Artificial Intelligence (AI), adaptive and non-adaptive, multi-agent, hybrid). This paper indicates the possible research gaps and highlights the applications possibilities and methods’ limitations in the area of DGs.

Little in the scholarly economics literature is directed specifically to the performance of sta­ble value funds, although they occupy a leading place among retirement investment vehicles. They are currently offered in more than one-third of all defined contribution plans in the USA, with more than $800 billion of assets under management. This paper rigorously ex­amines their performance throughout the entire period since their inception in 1973. We produce a composite index of stable value returns. We next conduct mean-variance analysis, Sharpe and Sortino ratio analysis, stochastic dominance analysis, and optimal multi-period portfolio composition analysis. Our evidence suggests that stable value funds dominate (on average) two major asset classes based on a historical analysis, and that they often occupy a significant position in optimized portfolios across a broad range of risk aversion levels. We discuss factors that contributed to stable value funds’ past performance and whether they can continue to perform well into the future. We also discuss considerations regarding whether or not to include stable value as an element in target date funds within defined con­tribution pension plans.

A series of precise data consisting of zircon U–Pb ages, whole-rock geochemistry and Sr–Nd–Hf isotope compositions from the Huhetaoergai granitic pluton was collected in this study and combined with data from the western Huhetaoergai, Zhuxiaogubuhe and Yagan granitic plutons to constrain the petrogenesis and tectonic setting of granitic plutons in the northern Ya-Gan fault zone, North Alxa, China. The Huhetaoergai pluton is composed of hornblende diorite, medium- to coarse-grained biotite adamellite and coarse-grained biotite adamellite with K-feldspar megacrysts. The U–Pb zircon ages of biotite adamellite are 220.5 ± 1.9 Ma and 226.5 ± 2.4 Ma. These granitoids are I-type granites with highly radiogenic initial ⁸⁷Sr/⁸⁶Sr of 0.708085–0.735470, negative eNd(t) average values of −2.98–3.23 and high eHf(t) of 9–11.05. These features indicate the granitoids were formed from magmas generated from juvenile crust. We speculate that the granitoids of the Huhetaoergai pluton were emplaced during an episode of intense intraplate orogenic movement evolution in an extrusional setting after a period of extensional postcollisional intraplate evolution.

This study identifies the optimal management policy of a given energy storage system (ESS) installed in a grid-connected wind farm for maximizing the monetary benefits and provides guidelines for defining the economic value of the ESS under the optimal management policy and selecting the optimal size of the ESS based on the economic value. Considering stochastic models for wind power and electricity price, we develop a finite-horizon periodic-review Markov decision process (MDP) model to seek the optimal management policy. We also use a simple optimization model to find the optimal storage capacity and charging/discharging capacity of the ESS. By applying our analytic approach to a real-world grid-connected wind farm located in South Korea, we verify the usefulness of this study. Our numerical study shows that the economic value of the ESS is highly dependent on the management policy, wind electricity variability, and the electricity price variability. Thus, the optimal size of ESS should be carefully determined based on the locational characteristics and management policy even with limited investments. Furthermore, this study provides a meaningful policy implication on how much a subsidy the government should provide for installing ESS in a wind farm.

Autonomous navigation of spacecraft necessitates innovative technologies, methods, and algorithms, particularly when orbiting in proximity of other space objects. Optimization methods are useful for autonomous spacecraft navigation, guidance, and control, but their performance is hampered by noisy multi-sensor technologies and poorly modeled system equations, and real-time on-board utilization is generally computationally burdensome. Some proposed methods use noisy sensor data to learn the optimal guidance and control solutions real-time (online), where non-iterative instantiations are preferred to reduce computational burdens. This study aims to highlight efficacy and limitations of several common methods for optimizing guidance and control while proposing a few more, where all methods are applied to the full, nonlinear, coupled equations of motion including cross-products of motion from the transport theorem. Five disparate types of optimum guidance and control algorithms are presented and compared to a classical benchmark. Comparative analysis is based on tracking errors (both states and rates), fuel usage, and computational burden. Real-time optimalization with singular switching plus nonlinear transport theorem decoupling proves superior by matching open-loop solutions to the constrained optimization problem (in terms of state and rate errors and fuel usage), while robustness is validated in the utilization of mixed, noisy state and rate sensors and uniformly varying mass and mass moments of inertia. State tracking errors are reduced one-hundred ten percent. Rate tracking errors are reduced one-hundred thirteen percent. Control utilization (e.g., fuel) is reduced eighty four percent, while computational burden in reduced ten percent simultaneously.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

Looking at different operating climatic conditions, the electrical behavior predicting photovoltaic modules gets very important. For the estimation of output power from photovoltaic (PV) plants this is a very essential and basic aspect. In this paper, the relationship between the I-V curve and the irradiation spectrum is discussed by combining the single diode model. An explicit elementary analytical model with two defined shape parameters is discussed and improved with three approximations and second order Taylor expansion. Then, the explicit elementary analytical model is investigated under varying conditions leveraging the four parameters I_ph, I₀, R_s and R_sh from the single diode model. The relationship between the physical parameters and the condition parameters are discussed and applied to extract the shape parameters at different scenarios. Considering the aging effect, the process of calculation to predict the I-V curve under different splitting spectra is simplified as follow: (1) two shape parameters are gotten from the I-V data at measurement reference conditions (MRC); (2) the short circuit current, open circuit voltage and shape parameters under any splitting spectrum can be calculated based on the relationship provided in article; (3) the performance of PV panel can be predicted with parameters. The validation of this model was experimentally proven leveraging monocrystalline silicon photovoltaic module with different splitting films. Results showed that the model accurately predicts the I-V characteristics for the examined PV modules at different irradiance spectra and cell temperatures. Moreover, the presented model performs superior compared to other investigated models when looking at accuracy and simplicity.

Exoskeleton robots are a rising technology in industrial contexts to assist humans in onerous applications. Mechanical and control design solutions are intensively investigated to achieve a high performance human-robot collaboration (e.g., transparency, ergonomics, safety, etc.). However, the most of the investigated solutions involve high-cost hardware, complex design solutions and standard actuation. In the presented work, an industrial exoskeleton for lifting and transportation of heavy parts is proposed. A low-cost mechanical design solution is proposed, exploiting compliant actuation at the shoulder joint to increase safety and transparency in human-robot cooperation. A hierarchic model-based controller is then proposed (including the modeling of the compliant actuator) to actively assist the human while executing the task. An inner optimal controller is proposed for trajectory tracking, while an outer fuzzy logic controller is proposed to online deform the task trajectory on the basis of the human’s intention of motion. A gain scheduler is also designed to calculate the optimal control gains on the basis of the performed trajectory. Simulations have been performed in order to validate the performance of the proposed device, showing promising results. The prototype is under realization.

The incorporation of renewable energy into power systems poses serious challenges to the transmission and distribution power system operators (TSOs and DSOs). To fully leverage these resources there is a need for a new market design with improved coordination between TSOs and DSOs. In this paper we propose two coordination schemes between TSOs and DSOs: one centralised and another decentralised that facilitate the integration of distributed based generation; minimise operational cost; relieve congestion; and promote a sustainable system. To this end, we approximate the power equations with linearised equations so that the resulting optimal power flows (OPFs) in both the TSO and DSO become convex optimisation problems. In the resulting decentralised scheme, the TSO and DSO collaborate to optimally allocate all resources in the system. In particular, we propose an iterative bi-level optimisation technique where the upper level is the TSO that solves its own OPF and determines the locational marginal prices at substations. We demonstrate numerically that the algorithm converges to a near optimal solution. We study the interaction of TSOs and DSOs and the existence of any conflicting objectives with the centralised scheme. More specifically, we approximate the Pareto front of the multi-objective optimal power flow problem where the entire system, i.e., transmission and distribution systems, is modelled. The proposed ideas are illustrated through a five bus transmission system connected with distribution systems, represented by the IEEE 33 and 69 bus feeders.

In this paper, a mathematical model of breast cancer governed by a system of ordinary differential equations in the presence of chemotherapy treatment and ketogenic diet is discussed. Several comprehensive mathematical analysis was carried out using varieties of analytical methods to study the stability of the breast cancer model. Also, sufficient conditions on parameter values to ensure cancer persistence in the absence of anti-cancer drugs ketogenic diet and cancer emission when anti-cancer drugs, immune-booster, ketogenic diet are included were established. Furthermore, optimal control theory is applied to find out the optimal drug adjustment as an input control of the system therapies to minimize the number of cancerous cells by considering different controlled combinations of administering the chemotherapy agent and ketogenic diet using the popular Pontryagin’s Maximum Principle. Numerical simulations were presented to validate our theoretical results.

This paper introduces a closed-loop control strategy for maintaining consistency of liquid temperature in commercial Drop on Demand (DoD) inkjet printing. No additional sensors or additional actuators are installed in the printhead while achieving the consistency in liquid temperature. To this end, this paper presents a novel in situ sensing-actuation policy at every individual liquid-nozzle, where the jetting mechanism has three distinct roles. It is used for jetting liquid droplet onto the print media based on the print-job. It is used as a soft sensor to estimate the real-time liquid temperature of the jetting nozzle. While not jetting liquid, it is used as a heating actuator to minimize the gradient of liquid temperature among nozzles. The soft sensing based in situ controller is implemented in an experimentally validated digital twin that models the thermo-fluidic processes of the printhead. The digital twin is scalable and flexible to incorporate an arbitrary number of liquid-nozzles, making the control strategy applicable for future designs of the printhead.

In this paper, a multi-operator differential evolution algorithm (MODE) is proposed to solve the Optimal Power Flow (OPF) problem and is called MODE-OPF. The MODE-OPF utilizes the strengths of more than one differential evolution (DE) operator in a single algorithmic framework. Additionally, an adaptive method (AM) is proposed to update the number of solutions evolved by each DE operator based on both the diversity of population and quality of solutions. This adaptive method has the ability to maintain diversity at the early stages of the optimization process and boost convergence at the later ones. The performance of the proposed MODE-OPF is tested by solving OPF problems for both small and large IEEE bus systems (i.e., IEEE-30 and IEEE-118) while considering the intermittent solar and wind power generation. To prove the suitability of this proposed algorithm, its performance has been compared against several state-of-the-art optimization algorithms, where MODE-OPF outperforms other algorithms in all experimental results and thereby improving a network's performance with lower cost. MODE-OPF decreases the total generation cost up to 24.08%, the real power loss up to 6.80% and the total generation cost with emission up to 8.56%.

Background: Outbreak of the Covid-19 is now an ongoing global health emergency. At the end of December 2019, the first infection was reported in Wuhan and the world did not pay attention to this extremely contaminated disease and plucked to react rapidly. The World is in an vulnerable state in disease spreading, facing a great loss of lives and socio-economic aspects also. That is why we have proposed a potential mathematical model with data analysis to predict and control the outcome of this pandemic. Methods: The model presented the epidemic dynamics of multiple compartments. We collected available online data of Spain. In primary step, we estimated the parameters using either the data analysis or reference papers. Then we did the data fitting analysis in comparison with the outcome of our mathematical results. The results of the system depended not only the parameters also on social consciousness. Results: It is found that disease progression in this model is determined by the basic reproductive ratio, $R_0$, the actual epidemic of $R_0$ and effective $R(t)$ of each day. If $R_0>1$, the number of latently infected individuals grows exponentially; endemic solution is stable while infection rate decays if $R_0<1$. The optimal control theory stated that vaccination and treatment strategies are highly effective for reducing both susceptible and infected population and to increase the recover rate high. In Spain, after state of alarm (quarantine) on 14 March 2020, reported cases increasing for 13 days only and from the 14th day, daily reported cases started to decline albeit with small fluctuation. Our proposed model approximates that the disease in Spain could be fully under control by after July 2020. Conclusion: Outbreak will be in control of health care system, reduce the death rate and will ensure social-economic stability.

In this paper we investigate the optimal investment strategy for a defined contribution (DC) pension plan during the decumulation phrase which is risk-averse and pays close attention to inflation risk. The plan aims to maximize the expected constant relative risk aversion (CRRA) utility from the terminal wealth by investing the wealth in a financial market consisting of an inflation-indexed bond, an ordinary zero coupon bond and a risk-free asset. We derive the optimal investment strategy in closed-form using the dynamic programming approach by solving the corresponding Hamilton-Jacobi-Bellman (HJB) equation. Our theoretical and numerical results reveal that under some rational assumptions, an inflation-indexed bond do has significant advantage to hedge inflation risk.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

Reemergence of deep Neural Networks (CNNs) has lead to high-performance supervised learning algorithms for the Electro-Optical (EO) domain classification and detection problems. This success is possible because generating huge labeled datasets has become possible using modern crowdsourcing labeling platforms such as Amazon Mechanical Turk that recruit ordinary people to label data. Unlike the EO domain, labeling the Synthetic Aperture Radar (SAR) domain data can be a lot more challenging and for various reasons using crowdsourcing platforms is not feasible for labeling the SAR domain data. As a result, training deep networks using supervised learning is more challenging in the SAR domain. In the paper,we present a new framework to train a deep neural network for classifying Synthetic Aperture Radar (SAR) images by eliminating the need for huge labeled dataset. Our idea is based on transferring knowledge from a related EO domain problem, where labeled data is easy to obtain. We transfer knowledge from the EO domain through learning a shared invariant cross-domain embedding space that is also discriminative for classification. To this end, we train two deep encoders that are coupled through their last year to map data points from the EO and the SAR domains to the shared embedding space such that the distance between the distributions of the two domains is minimized in the latent embedding space. We use the Sliced Wasserstein Distance (SWD) to measure and minimize the distance between these two distributions and use a limited number of SAR label data points to match the distributions class-conditionally. As a result of this training procedure, a classifier trained from the embedding space to the label space using mostly the EO data would generalize well on the SAR domain. We provide theoretical analysis to demonstrate why our approach is effective and validate our algorithm on the problem of ship classification in the SAR domain by comparing against several other learning competing approaches.

Coronavirus disease (COVID-19) is a new discovered strain where WHO officially declares the disease as COVID-19 while the virus responsible for it called Severe Acute Respiratory Syndrome Coronavirus 2 or SARS-CoV-2. The incubation period of this disease is between 14 days. Ordinary clinical symptoms that reported around the world include fever, cough, fatigue, diarrhoea and vomiting as well as asymptomatic for certain people. Infection is spread mainly through broad droplets. In early March 2020, WHO again has announced that COVID-19 is a pandemic with currently no specific treatment. The potential use of SARS-COV-2 proteome as a vaccine candidate by analysing through B-cell and T-cell antigenicity by using a immunoinformatics approach as a vaccine development early stage. In this study, we used consensus sequence for SARS-COV-2 proteome that was retrieved from NCBI database. VaxiJen 2.0 was mainly used to identify the antigenic property of SARS-COV-2 proteins. IEDB then used to analyse the B-cell epitope, the presence of T cell immunogenic epitope in SARS-COV-2 proteins was obtained by using compromise method of MHC class I and II tools that accessible respectively using ProPred-1 server and MHC II Binding Prediction in IEDB database. The best epitopes of B and T-cell epitopes were predicted with high antigencity and the information is disseminated through web-based database resource (https://covid-19.omicstutorials.com/epitopes/). This study will be useful to find a new epitope-based candidate for SARS-COV-2. However, further study needs to be done for the next stages of vaccine development.

Human African Trypanosomiasis (HAT) commonly known as sleeping sickness, is a neglected tropical vector borne disease caused by trypanosome protozoa. It is transmitted by bites of infected tsetse fly. In this paper we first present the vector-host model which describes the general transmission dynamics of HAT. In the tsetse fly population, the HAT is modelled by three compartments while in the human population, the HAT is modelled by four compartments. The next generation matrix approach is used to derive the basic reproduction number, R₀, and also it is proved that if R₀ ≤ 1 the disease free equilibrium is globally asymptotically stable, which means the disease dies out. The disease persist in the population if the value of R₀ > 1. Furthermore, the optimal control model is determined by using the Pontryagin’s maximum principle with control measures such as education, treatment and insecticides used to optimize the objective function. The model simulations confirm that the use of the three control measures are very efficient and effective to eliminate HAT in Africa.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

Dysregulation of the angiotensin-II Type-I receptor (AT1R) and its pathway was reported to associate with poor-prognosis in several malignancies, including colorectal-cancer (CRC). We have explored the therapeutic-potential of targeting AT1R using valsartan, and its pharmacological-interaction with Fluorouracil (5-FU) in CRC. Anti-proliferative function was evaluated in 2-/3-dimensional cells and in vivo models. Anti-proliferative, anti-migratory, apoptotic function and effect on cell-cycle was assessed by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT), wound-healing test, and Fluorescence-activated cell sorting (FACS), respectively, while gene-expression was determined at mRNA/protein levels. By histogical analysis and measuring of oxidative/antioxidant markers, we evaluated the anti-inflammatory properties of valsartan. Valsartan suppressed cell-growth and impacted the anti-tumor-activities of 5-FU by apoptosis-induction. Valsartan inhibited the cells migration by perturbation of Matrix metalloproteinase (MMP1). Furthermore, valsartan inhibited tumor-growth and metastasis, and this was more notable in valsartan/5-FU combination-treated-group. The mechanism was plausible to be via the induction of Reactive-oxygen-species (ROS) and down-regulation of Superoxide-dismutase (SOD), thiol/catalase (CAT) as well as Vascular endothelial growth factor (VEGF) and Transforming growth factor beta (TGF-β). Valsartan may protect cells against intestinal fibrosis by modulation of pro-fibrotic and pro-inflammatory components include fibronectin, Interleukin) IL-1β (, Tumor necrosis factor alpha) TNF-α (, Interferon gamma) INF-γ (, and Monocyte Chemotactic Protein 1 (MCP-1). Our findings demonstrated that targeting the AT1R receptor may inhibit tumor-growth and ameliorate fibrosis and inflammation associated with CRC via modulation of AT1 and TGF-β pathways.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Rapid diagnosis of acute myocardial infarction is critical for intervention and treatment to decrease morbidity and mortality. For this reasons, this study aimed to design a sensitive biosensor for cardiac troponin I (cTnI) for early prediction and intervention. The sensor was designed from golden plate immobilized with anti- cTnI antibody conjugated with horseradish peroxidase (HRP) enzyme. The rate of degradation of H2O2 is directly related to serum cTnI level. Serum cTnI level was quantified from 3 studied groups including; healthy subjects and patients with ischemic heart (IHD) diseases and myocardial infarction (MI) by ELISA and biosensor techniques to achieve the improved sensitivity of the biosensor. It was found that cTnI levels in healthy subjects ranged from 8-13 ng/dl and in patients with IHD ranged from 20 - 41 ng/dl and MI range from 57- 180 ng/dl. The sensitivity of biosensor was ranged from 85-95% compared with ELISA technique. The developed biosensor is promising in ICU hospitals for early diagnosis and prevent complications of the stroke. It is recommended to apply this biosensor in the large scale of patients with different stages of the cardiac disease.

This paper addresses the problem of assessing and optimizing acoustic positioning system for underwater target localization with range measurements only. We present a new three-dimensional assessment model to assess the optimal geometric beacon formation whether meet user needs. For the sake of mathematical tractability, it is assumed that the measurements of the range between the target and beacons are corrupted with white Gaussian noise with variance is distance-dependent. Then by adopting dilution of precision (DOP) parameters in the assessment model, the relationship between DOP parameters and positioning accuracy is derived. In addition, the optimal geometric beacon formation that will yield the best performance is achieved by minimizing the values of geometric dilution of precision (GDOP) on condition that the position of target is known and fixed. Next, in order to make sure whether the estimate positioning accuracy over interesting region satisfy the precision needed by the users, geometric positioning accuracy (GPA), horizonal positioning accuracy (HPA) and vertical positioning accuracy (VPA) are utilized to assess the optimal geometric beacon formation. Simulation examples are designed to illustrate the exactness of the conclusion. Unlike other work which only use GDOP to optimize the formation and cannot assess the performance of the specified dimensions, this new three-dimensional assessment model can assess the optimal geometric beacon formation in each dimension for any point in three-dimensional space, which can provide users with guidance advices to optimize performance of every specified dimension.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

As shown in former papers, the nonadiabatic Heisenberg model presents a novel mechanism of Cooper pair formation generated by the strongly correlated atomic-like motion of the electrons in narrow, roughly half-filled "superconducting bands". These are energy bands represented by optimally localized spin-dependent Wannier functions adapted to the symmetry of the material under consideration. The formation of Cooper pairs is not the result of an attractive electron-electron interaction but can be described in terms of quantum mechanical constraining forces constraining the electrons to form Cooper pairs. There is theoretical and experimental evidence that only this nonadiabatic mechanism operating in superconducting bands may produce eigenstates in which the electrons form Cooper pairs. These constraining forces stabilize the Cooper pairs in any superconductor, whether conventional or unconventional. Here we report evidence that also the experimentally found superconducting state in bismuth at ambient as well as at high pressure is connected with a narrow, roughly half-filled superconducting band in the respective band structure. This observation corroborates once more the significance of constraining forces in the theory of superconductivity.

We construct a family of two-step optimal fourth order iterative methods for finding single root of non-linear equations. We generalize these methods to simultaneous iterative methods for determining all the distinct as well as multiple roots of single variable non-linear equations. Convergence analysis is present for both cases to show that the order of convergence is four in case of single root finding method and is twelve for simultaneous determination of all roots of non-linear equation. The computational cost, Basin of attraction, efficiency, log of residual and numerical test examples shows, the newly constructed methods are more efficient as compared to the existing methods in literature.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

This paper addresses a wildlife monitoring problem using a team of UAVs for efficient monitoring of wildlife. The state-of-the-art technology using UAVs has been an increasingly popular tool to monitor wildlife compared to the traditional methods such as satellite imagery-based sensing or GPS trackers. However, there still exist unsolved problems as to how the UAVs need to cover a spacious domain to detect animals as many as possible. In this paper, we propose the optimal transport-based wildlife monitoring strategy for a multi-UAV system, to prioritize monitoring areas while incorporating complementary information such as GPS trackers and satellite-based sensing. Through the proposed scheme, the UAVs can explore the large-size domain effectively and collaboratively with a given priority. The time-varying nature of wildlife due to their movements is modeled as a stochastic process, which is included in the proposed work to reflect the spatio-temporal evolution of their position estimation. In this way, the proposed monitoring plan can lead to efficient wildlife monitoring with a high detection rate. Various simulation results including statistical data are provided to validate the proposed work.

Multiobjective optimization plays an increasingly important role in modern applications, where several criteria are often of equal importance. The task in multiobjective optimization and multiobjective optimal control is therefore to compute the set of optimal compromises (the Pareto set) between the conflicting objectives. The advances in algorithms and the increasing interest in Pareto optimal solutions have led to a wide range of new applications related to optimal and feedback control which results in new challenges such as expensive models or real-time applicability. Since the Pareto set generally consists of an infinite number of solutions, the computational effort can quickly become challenging which is particularly problematic when the objectives are costly to evaluate or when a solution has to be presented very quickly. This article gives an overview over recent developments in accelerating multiobjective optimal control for complex problems where either PDE constraints are present or where a feedback behavior has to be achieved. In the first case, surrogate models yield significant speed-ups. Besides classical meta-modeling techniques for multiobjective optimization, a promising alternative for control problems is to introduce a surrogate model for the system dynamics. In the case of real-time requirements, various promising model predictive control approaches have been proposed, using either fast online solvers or offline-online decomposition. We also briefly comment on dimension reduction in many-objective optimization problems as another technique for reducing the numerical effort.

Nucleoli are emerging as key sensors of cellular stress and regulators of the downstream consequences on proliferation, metabolism, senescence and apoptosis. NF-kB signalling is activated in response to a similar plethora of stresses, which leads to modulation of cell growth and death programs. Although these pathways are distinct, it is increasingly apparent that they converge at multiple levels. Exposure of cells to certain insults causes a specific type of nucleolar stress that is characterised by degradation of the PolI complex component, TIF-IA, and increased nucleolar size. Recent studies have shown that this atypical nucleolar stress lies upstream of cytosolic IkB degradation and NF-kB nuclear translocation. Under these stress conditions, the RelA component of NF-kB accumulates within functionally altered nucleoli to trigger a nucleophosmin dependent, apoptotic pathway. In this review, we will discuss these points of crosstalk and their relevance to the anti-tumour mechanism of aspirin and small molecule CDK4 inhibitors. We will also briefly discuss how NF-kB-nucleoli crosstalk may be more broadly relevant to the regulation of cellular homeostasis and how it may be exploited for therapeutic purpose.

This article, we study the sufficient conditions for the controllability of second-order impulsive partial neutral evolution differential systems with infinite delay in Banach spaces by using the theory of cosine families of bounded linear operators and fixed point theorem.

Optimal dividend payment under a ruin constraint is a two objective control problem which—in simple models—can be solved numerically by three essentially different methods. One is based on a modified Bellman equation and the policy improvement method (see Hipp C., 2003). In this paper we use explicit formulas for running allowed ruin probabilities which avoid a complete search and speed up and simplify the computation. The second is also a policy improvement method, but without the use of a dynamic equation (see Hipp C., 2003). It is based on closed formulas for first entry probabilities and discount factors for the time until first entry (see Hipp C., 2016). Third a new, faster and more intuitive method which uses appropriately chosen barrier levels and a closed formula for the corresponding dividend value. Using the running allowed ruin probabilities, a simple test for admissibility—concerning the ruin constraint—is given. All these methods work for the discrete De Finetti model and are applied in a numerical example. The non stationary Lagrange multiplier method suggested in (see Hipp C., 2016), Section 2.2.2 does also yield optimal dividend strategies which differ from those in all other methods, and Lagrange gaps are present here. These gaps always exist in De Finetti models, see (see Hipp C., 2017).

This study presents application of demand response strategy in a standalone wind-solar-battery hybrid energy system (HES). Inputs for the designed HES are wind speed, solar radiation, temperature and load demand which is variable with time. In this study, hourly values of meteorological data and hourly load demand are considered in one year. An improved gravitational search algorithm (IGSA) is used to optimize the configuration of the standalone wind-solar-battery hybrid power system. The optimal objectives of the system are cost of the system in life cycle, the loss of power supply probability（LPSP）and the energy excess percentage（EXC）.The effect of demand response on economic benefit and energy storage allocation of the standalone wind-solar-battery system is studied. The obtained optimal configuration of the proposed HES can provide minimal energy cost with excellent performance and reduced waste and unmet load.

The seeds of red clover are heteromorphic and two color morphs can be visually recognized, light purple and yellow, resulting from heterozygosity and recessive homozygosity at two loci. Here, we report the responses of seed imbibition, seed germination, and early seedling growth of the two morphs to distilled water, sodium chloride, and complete nutrient solution. The sensitivity of red clover seeds to treatments increased with the stage of development in what seems to be a cumulative process. No differences were found in seed imbibition between morphs or between treatments. In seedling growth, on the contrary, treatments were always effective, but differences between morphs were only observed in seeds that were treated with nutrient solution, whereas in the intermediate stage of seed germination, the effects by treatments were observed together with the appearance of differences between morphs in distilled water and in the treatment by sodium chloride solution. Simultaneously, the superior performance of the yellow morph that was found in germination, which appears to be a trait stable across cultivars of red clover seeds, turned into a superior performance of the light purple morph in seedling growth.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

ND1 subunit possesses the majority of the inhibitor binding domain of the human MRC-I. This is an attractive target for the search for new inhibitors that seek mitochondrial dysfunction. It is known, from in vitro experiments, some metabolites from Annona muricata called acetogenins have important biological activities such as anticancer, antiparasitic, and insecticide. Previous studies propose an inhibitory activity of bovine MRC-I by bis-THF acetogenins such as annocatacin B, however, there are few studies on its inhibitory effect on human MRC-I. In this work, we evaluate the molecular and energetic affinity of the annocatacin B molecule with the human ND1 subunit in order to elucidate its potential capacity to be a good inhibitor of this subunit. For this purpose, QM optimizations, MD simulations and MM/PBSA analysis were performed. As a control to compare our outcomes, the molecule rotenone, which is a known MRC-I inhibitor, was chosen. Our results show that annocatacin B has a greater affinity for the ND1 structure, its size and folding were probably the main characteristics that contributed to stabilize the molecular complex. Furthermore, the MM/PBSA calculations showed a 35% stronger BFE compared to the rotenone complex. Detailed analysis of the BFE shows that the aliphatic chains of annocatacin B play a key role in molecular coupling by distributing favorable interactions throughout the major part of the ND1 structure. These results are consistent with experimental studies that mention that acetogenins may be good inhibitors of MRC-I.

Studies have shown that in many practical applications, data interpolation by splines leads to better approximation and higher computational efficiency as compared to data interpolation by a single polynomial. Data interpolation by splines can be significantly improved if knots are allowed to be free rather than at a priori fixed locations such as data points. In practical applications, the smallest possible curvature is often desired. Therefore, optimal splines are determined by minimizing a derivative of continuously differentiable functions comprising the spline of the required order. The problem of obtaining an optimal spline is tantamount to minimizing derivatives of a nonlinear differentiable function over a Banach space on a compact set. While the problem of data interpolation by quadratic splines has been accomplished analytically, interpolation by splines of higher orders or in higher dimensions is challenging. In this paper, to overcome difficulties associated with the complexity of the interpolation problem, the interval over which data points are defined, is discretized and continuous derivatives are substituted by their discrete counterparts. It is shown that as the mesh of the discretization approaches zero, a resulting near-optimal spline approaches an optimal spline. Splines with the desired accuracy can be obtained by choosing an appropriate mesh of the discretization. By using cubic splines as an example, numerical results demonstrate that the linear programming (LP) formulation, resulting from the discretization of the interpolation problem, can be solved by linear solvers with high computational efficiency and resulting splines provide a good approximation to the optimal splines.

The activity of prioritizing software requirements should be done as efficiently as possible. Selecting the most stable requirements for the most important customers for the development company can be a positive factor when we consider that the available resource does not always encompass the implementation of all requirements. Quantitative methods for reaching software prioritization in releases are many in the field of Search-Based Software Engineering (SBSE). However, we show that it is possible to use qualitative Verbal Decision Analysis (VDA) methods to solve this same type of problem. Moreover, we will use the ZAPROS III-i methods to prioritize requirements considering the opinion of the decision-maker, who will participate in this process. Finally, the results obtained in the VDA structured methods were quite satisfactory when compared to the methods using SBSE. A comparison of results between quantitative and qualitative methods will be made and discussed later.

Human Perrault syndrome (PRLTS) is defined by autosomal recessive inheritance with primary ovarian insufficiency and early hearing loss. Most PRLTS disease proteins modulate mitochondrial transcription or translation. Among the genetic causes are ClpP mutations, which trigger also complete azoospermia, whose cellular and molecular underpinnings are unknown. Here, the ClpP-null mouse model was studied by global transcriptomics, proteomics, RT-qPCR, immunoblots, tissue fractionation, testis histology, and was crossed with STING/IFNAR mutants. Spermatogenesis showed accumulated early spermatocytes, versus deficits of desynapsis and kinetochore factors; excess Dazl/Stra8 and acetylSMC3, versus deficient SHCBP1L, were molecular correlates. Spermiogenesis showed few round spermatids, tsHMG/TFAM in elongated spermatids was absent; transcripts for tail/acrosome factors were downregulated from start. Nuclear anomalies included a failed Rec8 induction, early BRDT deficiency, histone H3 cleavage, and cGAMP increase, among antiviral responses typical of ClpP-mutants. However, deletion of downstream innate immune signals STING/IFNAR failed to reestablish fertility. As mitochondrial triggers, we observed accumulation of ClpX, with PTCD1, POLDIP2, GRSF1, ALKBH7, DNAJA3, AURKAIP1, VWA8, and Perrault proteins ERAL1, PEO1, HARS2, partially showing nuclear redistribution. ClpP-depletion is known to cause extra-mitochondrial release of mispacked mtDNA/mtRNA/protein complexes. Now we define nuclear inflammatory responses and meiotic arrest as consequences, similar to observations in mito-mice and mutator-mice.

The micropaleontological study (radiolarians and foraminifera) of the sediment core AMK-340, Reykjanes Ridge, North Atlantic, combined with the radiocarbon dating and Oxygen/Carbon isotopic record, provided data for the reconstruction of the summer paleotemperature on the water depth of 100 m, and paleoenvironments during the Termination I in the age interval of 14.5–8 ka. The response of the main microfossil species on the paleoceanographic changes within the Bølling-Allerød (BA) warming, the Younger Dryas (YD) cold event, and final transition to the warm Holocene was different. The BA warming was well reflected in the radiolarian and benthic but not planktic foraminiferal record. The high abundances of the cold-water radiolarian species Amphimelissa setosa as the Greenland/Iceland Sea indicator marked a cooling at the end of the BA and within the start of the YD at 13.2–12.3 ka. The micropaleontological and isotopic data together with the paleotemperature estimates for the Reykjanes Ridge at 60° N document that, after the warm BA, the middle YD ca. 12.5–12.2 ka was the next significant step toward the Holocene warming. Start of the Holocene interglacial conditions was reflected in abundant occurrence of the microfossils being indicators of the open boreal North Atlantic environments and lower oxygen isotope values indicating increasing warmth.

An SIRS (Susceptible–Infected–Removed-Susceptible) mathematical model for the transmission dynamics of the Transfusion–Transmitted Malaria (TTM) model with optimal control pair u₁(t) and u₂(t) was developed and studied in this research work. The model Transfusion–Transmitted Malaria disease–free equilibrium and endemic equilibriums points were determined. The model exhibited two equilibriums; disease-free and endemic equilibrium. It is shown that the disease–free equilibrium was locally asymptotically stable if the associated basic reproduction numbers R₀ is less than unity while the disease persists if R₀ is greater than unity. The global stability of the Transfusion–Transmitted Malaria model at the disease-free equilibrium was established using the comparison method. The optimality system was derived and an optimal control model of blood screening and drug treatment for the Transfusion–Transmitted Malaria model was investigated. Conditions for the optimal control were considered using Pontryagin’s Maximum Principle and solved numerically using the Forward and Backward Finite Difference Method (FBDM). Numerical results obtained are in perfect agreement with our analytical results.

In this paper, the design and control of a hydraulic system based tire changer machine have been analyzed and simulated using Matlab/Simulink Toolbox successfully. The machine have a displacement input which is a leg pedal displacement in order to push the piston of the pump to fed the motor with a pressured hydraulic fluid to rotate the tire with an angular speed to mount and dismount it. Augmentation based H_∞ and H₂ optimal synthesis controllers have been used to improve the performance of the machine. Comparison of the proposed controllers for tracking a reference input speed have been done using two reference inputs (step and random) signals. Finally the comparative simulation results proved the effectiveness of the proposed tire changer with H synthesis controller in improving the settling time and percentage overshoot.

Microgrid is one of the promising green transition technologies that will provide enormous benefit to the seaport, as a solution to the major concerns in this sector, namely energy crisis, economical and environmental pollution. However, finest design of the microgrid is a challenging task considering different objectives, constraints and uncertainties involved. To ensure the optimal operation of the system, determining the right configuration framework and size for each component in the seaport microgrid at the minimum cost is a vital decision at the design stage. This paper aims to design a hybrid system of seaport microgrid with optimally sized component .The selected case study is the Port of Aalborg, Denmark. The proposed grid-connected structure consists of renewable energy sources (photovoltaic system and wind turbines), an energy storage system and cold ironing as seaport’ loads. The architecture is then optimized by utilizing HOMER to meet the maximum load demand by considering a few parameters such as solar global horizontal irradiance, temperature and wind resources. Then, the best configuration framework is analyzed in terms of economic feasibility, energy reliability and environmental impact.

This paper reviews the low-resilience problem in many cities, poor designs of cities to cope with disasters, and the need for tolerance of urban constructions. It explores answers concerning the question of how shall we build cities resiliently? The method of this applied research is a multiphase process that considers all physical and socioeconomic elements of a city. It introduces six indicator groups of urban management (M), economy (E), built environments (U), Infrastructures (I), natural environments (N), and health protection (H). The groups include 55 indicators as variables in the mathematical calculations in this paper. This paper builds a mathematical model to maximize the profitability of resilient buildings by optimizing investments in the required projects. The projects will upgrade the firmness and tolerance of cities against nature-based and human-made dangers and risks. There is a linear programming in 55 variables to select optimal solutions from fifty-five factorial alternatives. Then, the programming will develop into non-linear programming. The unique innovation of this paper is its linear programming interpretation by non-linear to give optimal solutions for the problem. Applying the Lagrange function in the Kuhn-Tucker conditions proves the accuracy of the hypothesis that post-COVID urbanization requires maximum resilience. Only in this way, the urban economies will be free of risks. Outcomes in this paper will assist in the pre-planning, design, and building of built environments everywhere resilient and sustainable.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

Computer network attacks are evolving in parallel with the evolution of hardware and neural network architecture. Despite major advancements in Network Intrusion Detection System (NIDS) technology, most implementations still depend on signature-based intrusion detection systems, which can’t identify unknown attacks. Deep learning can help NIDS to detect novel threats since it has a strong generalization ability. The deep neural network’s architecture has a significant impact on the model’s results. We propose a genetic algorithm based model to find the optimal number of hidden layers and the number of neurons in each layer of the deep neural network (DNN) architecture for the network intrusion detection binary classification problem. Experimental results demonstrate that the proposed DNN architecture shows better performance than classical machine learning algorithms at a lower computational cost.

The survival analysis of the Cancer Genome Atlas (TCGA) dataset is a well-known method to discover the gene expression-based prognostic biomarkers of head and neck squamous cell carcinoma (HNSCC). A cutoff point is usually used in survival analysis for the patients' dichotomization in the continuous gene expression. There is some optimization software for cutoff determination. However, the software's predetermined cutoffs are usually set at the median or quantiles of gene expression value to perform the analyses. There are also few clinicopathological features available on their pre-processed data sets. We applied an in-house workflow, including data retrieving and pre-processing, feature selection, sliding-window cutoff selection, Kaplan-Meier survival analysis, and Cox proportional hazard modeling for biomarker discovery. In our approach for the TCGA HNSCC cohort, we scanned human protein-coding genes to find optimal cutoff values. After adjustment with confounders, the clinical tumor stage and the surgical margin involvement are independent risk factors for patients' prognosis. According to the resulting tables with Bonferroni-adjusted P value under the optimal cutoff and the hazard ratio, three biomarker candidates, CAMK2N1, CALML5, and FCGBP, are significantly associated with the patients' overall survival. We validated this discovery by using the other independent HNSCC dataset (GSE65858). Thus, we suggest the transcriptomic analysis could help for biomarker discovery.

Japanese encephalitis (JE) is a vaccine preventable disease caused by the Japanese encephalitis virus (JEV), which is primarily prevalent in Asia. JEV is a Flavivirus, classified into a single serotype with five genetically distinct genotypes (I, II, III, IV, and V). JEV genotype III (GIII) had been the most dominant strain and caused numerous out breaks in the JEV endemic countries until 1990. However, recent data shows the emergence of genotype I (GI) as a dominant genotype and it is gradually displacing GIII. The exact mechanism of this genotype displacement is still unclear. The virus can replicate in mosquito vectors and vertebrate hosts to maintain its zoonotic life cycle; pigs and aquatic wading birds act as an amplifying/reservoir hosts, and humans and equines are the dead end hosts. The important role of pigs as an amplifying host for JEV is well known. However, the influence of other domestic animals especially birds that live in high abundance and close proximity to human is not well studied. Here, we strive to briefly highlight the role of birds in JEV zoonotic transmission, discovery of birds as a natural reservoirs and amplifying host for JEV, species of birds susceptible to JEV infection, and the proposed effect of JEV on poultry industry in future perspective which have been neglected for a long times. We also discussed the recent in vitro and in vivo studies which show that the newly emerged GI viruses replicated more efficiently in bird-derived cells and ducklings/chicks than GIII, and an important role of birds in the JEV genotype shift from GIII to GI.

Manufacturers of photovoltaic modules do not provide all the information necessary to predict their performance under different climatic conditions. This forces the development of mathematical models of behavior and the application of mathematical methods for the calculation of their associated parameters. A toolbox called PVMSim implemented in MATLAB/GUI is proposed in this paper. PVMSIm provides models allowing the simulation of photovoltaic modules. A two-diode model is used to represent the effect of irradiance and temperature on the V-I and V-P characteristic curves. The accuracy of PVMSim has been vaildated by applying the models to two mono-crystalline and multi-crystalline solar modules of different power ratings and manufacturers. The model PVMSim model accuracy was verified against the manufacturer’s datasheet. This paper shows that this tool is useful for designers and professionals who require an intuitive graphical interface for fast and accurate modeling, simulation and sizing of photovoltaic systems.

Curcumin, a natural polyphenolic compound isolated from the plant Curcuma longa, is known to induce autophagy in various cancer cells, including lung cancer. In the present study, we also confirmed by LC3 immunofluorescence and immunoblotting analyses that curcumin triggers autophagy in human lung adenocarcinoma A549 cell line. In parallel with autophagy induction, gene expression of human GD3 synthase (hST8Sia I) responsible for ganglioside GD3 synthesis was markedly elevated in response to curcumin in A549 cells. To investigate transcriptional activation of hST8Sia I associated with autophagy formation in curcumin-treated A549 cells, functional characterization of the 5’-flanking region of the hST8Sia I gene was carried out using luciferase reporter assay system. Deletion analysis demonstrated that the -1146 to -646 region, which includes putative c-Ets-1, CREB, AP-1 and NF-κB binding sites, functions as the curcumin-responsive promoter of hST8Sia I in A549 cells. Site-directed mutagenesis and chromatin immunoprecipitation assay demonstrated that the NF-κB binding site at -731 to -722 was indispensable for the curcumin-induced hST8Sia I gene expression in A549 cells. Moreover, the transcriptional activation of hST8Sia I by curcumin A549 cells was strongly inhibited by compound C, an inhibitor of AMP-activated protein kinase (AMPK). These results suggest that curcumin controls hST8Sia I gene expression via AMPK signal pathway in A549 cells.

Hippophae is a tree species with ecological, economic and social benefits. In this study, we assembled and annotated chloroplast genomes of sympatric Hippophae gyantsensis and H. rhamnoides subsp. yunnanensis. Their full-length are 155260 and 156415 bp, respectively. Each of them has 131 genes, comprising 85 protein-coding genes, 8 ribosomal RNA genes and 38 transfer RNA genes. After comparing the chloroplast genomes, we found 1302 base difference loci, and 63.29% are located in the intergenic region or intron sequences and 36.71% are located in the coding sequences. The SSC region has the highest mutation rate, followed by the LSC region; the IR regions have the lowest mutation rate. Among the protein-coding genes, three had a ratio of nonsynonymous to synonymous substitutions (Ka/Ks) >1 (but P values were non-significant) and 66 had Ka/Ks <1 (46 were significant). In general, the chloroplast protein-coding genes may be subject to purification selection. Among H. gyantsensis and H. rhamnoides subsp. yunnanensis chloroplast protein-coding genes, there are 20 and 16 optimal codons, respectively. Most of the optimal codons were ending with A or U, which indicates significant AT preference. It is an important reference for studies on the general characteristics and evolution of the Hippophae chloroplast genome.

The role of innate immunity in neutralization of viral infections (including COVID-19) and forming long-lasting and specific immune memory is considered. It is assumed that antiviral protection is generated by the mechanism of RNA interference (RNAi) and is based on the presence of specific viral patterns in the DNA library of the host cells.

Aberrant neutrophil extracellular trap (NET) formation and the loss of barrier integrity in inflamed intestinal tissues have long been associated with inflammatory bowel disease (IBD). However, whether NETs alter intestinal epithelium permeability during colitis remains elusive. Here, we demonstrated that NETs promote the breakdown in intestinal barrier function for the pathogenesis of intestinal inflammation in mouse models of colitis. NETs were abundant in the colon of mice with colitis experimentally induced by dextran sulfate sodium (DSS) or 2,4,6-trinitrobenzene sulfonic acid (TNBS). Analysis of the intestinal barrier integrity revealed that NETs impaired gut permeability, enabling the initiation of luminal bacterial translocation and inflammation. Furthermore, NETs induced the apoptosis of epithelial cells and disrupted the integrity of tight junctions and adherens junctions. Intravenous administration of DNase I, an enzyme that dissolves the web-like DNA filaments of NETs, during colitis restored the mucosal barrier integrity which reduced the dissemination of luminal bacteria, and attenuated intestinal inflammation in both DSS and TNBS models. We conclude that NETs serve a detrimental factor in the gut epithelial barrier function leading to the pathogenesis of mucosal inflammation during acute colitis.

The paper is concerned with a class of stochastic differential equations in infinite dimensional Hilbert space with random coefficients driven by Teugel's martingales which are more general processes. and its optimal control problem. Here Teugels martingales are a family of pairwise strongly orthonormal martingales associated with L\'{e}vy processes (see Nualart and Schoutens). There are three major ingredients. The first is to prove the existence and uniqueness of the solutions by continuous dependence theorem of solutions combining with the parameter extension method. The second is to establish the stochastic maximum principle and verification theorem for our optimal control problem by the classicconvex variation method and dual technique.The third is to represent an example of a Cauchy problem for a controlled stochastic partial differential equation driven by Teugels martingales which our theoretical results can solve.

The prim objective of commenced article is to determine q-sumudu transforms of a product of unified family of q-polynomials with basic (or q-) analogue of fox’s H-function and q-analog of I-functions. Specialized cases of the leading outcome are further evaluated as q-sumudu transform of general class of q-polynomials and q-sumudu transforms of the basic analogues of Fox’s H-function and I-functions.

Enhancing the effectiveness of search and rescue operation at sea is always a duty of utmost importance of the coastal states. The search area for distressed objects can be determined by using Monte Carlo simulation, combined with the Median-Filter. Once the search area has been identified, the success of search and rescue operations depends on the sweeping ability of search and rescue vessel at the probability area of the distress object with the minimum time. This is the important element to the success of the search and rescue operation as it minimizes the risk and cost for Search and rescue team. In this article, the authors study and propose the use of Bacterial Foraging Optimization Algorithm (BFOA) to calculate the optimal search and co-ordination route for many search and rescue vessels in Vietnam sea. The simulation results show that it is quite consistent with reality and BFOA can be effectively applied to determine a quick search.

In this paper, a study of modeling PV cell (solar cell), PV module (solar modules) and PV array solar array) using Matlab/Simulink software is presented. This study is focused on the study to design photovoltaic cell, photovoltaic modules, photovoltaic panels and PV array (solar array) and to analyze the change in PV performance according to changes in different parameters such temperature, solar irradiation, reverse saturation current, series resistance and shunt resistance. This study shows the PV and IV characteristics curve for each model from which MPP (maximum power point) is determined. In this study, different PV and IV characteristic curves are gained for varying temperatures with specified solar irradiation conditions,s and then the MPP is tracked. The highest power output is also compared between the designed PV module and the selected PV module (MX Solar USA MX60-245)

There is high confidence that climate change has increased the probability of concurrent temperature-precipitation extremes, changed their spatial-temporal variations, and affected the relationships between drivers of such natural hazards. However, the extent of such changes has been less investigated in Australia. Daily weather data (131 years, 1889-2019) at 700 grid cells (1◦ × 1◦) across Australia was obtained to calculate annual and seasonal mean daily maximum temperature (MMT) and total precipitation (TPR). A nonparametric multivariate copula framework was adopted to estimate the return period of compound hot-dry (CHD) events based on an ‘And’ hazard scenario (hotter than a threshold ‘And’ drier than a threshold). CHD extremes were defined as years with joint return periods of larger than 25 years. Mann-Kendall nonparametric tests was used to analyse trends in MMT and TPR as well as in the frequency of univariate and CHD extremes. A general cooling-wetting trend was observed over 1889-1989. Significant increasing trends were detected over 1990-2019 in the frequency and severity of hot extremes across the country while trends in dry extremes were mostly insignificant (and decreasing). Results showed a significant increase in the association between temperature and precipitation at various temporal scales. The frequency of CHD extremes was mostly stable over 1889-1989, but significantly increased between 1990 and 2019 at 44% of studied grid cells, mostly located in the north, south-east and south-west. Spatial homogeneity (i.e. connectedness) and propagation of extreme events from one grid cell to its neighbouring cells was investigated across Australia. It can be concluded that this connectedness has not significantly changed since 1889.

Optimal conditions for maximum efficacy of photoinitiated polymerization are theoretically presented. Analytic formulas are shown for the crosslink time, crosslink depth and efficacy function. The roles of photoinitiator (PI) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented. For optimal efficacy, a strategy via controlled PI concentration is proposed, where re-supply of PI in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced. Experimental data are analyzed for the role of PI concentration and light intensity on the gelation time and efficacy.

In this paper, we introduce and study the notion of rough I₂-lacunary statistical convergence of double sequences in normed linear spaces. We also introduce the notion of rough I₂-lacunary statistical limit set of a double sequence and discuss about some properties of this set.

A study of Bianchi Type I cosmological model is undertaken in the framework of creation of particles. To accommodate the creation of new particles, the universe is regarded as an Open thermodynamical system. The energy conservation equation is modified with the incorporation of a creation pressure in the energy momentum tensor. Exact solutions of the field equations are obtained (i) for a particular choice of the particle creation function and (ii) by considering the deceleration parameter to be constant. In the first model the behavior of the solution at late times is investigated. The physical aspects of the model have also been discussed. In the case of the second model we have restricted our analysis to the power law behaviour for the average scale factor. This leads to a particular form for the particle creation function. The behavior of the solution is investigated and the physical aspects of the model have also been discussed for the matter dominated era.

This work aims to develop an autonomous system for the unmanned aerial vehicle (UAV) to land on a moving platform such as the automobile or marine vessels, providing a promising solution for a long-endurance flight operation, a large mission coverage range, and a convenient recharging ground station. Different from most state-of-the-art UAV landing frameworks which rely on UAV’s onboard computers and sensors, the proposed system fully depends on the computation unit situated on the ground vehicle/marine vessel to serve as a landing guidance system. Such novel configuration can therefore lighten the burden of the UAV and computation power on the ground vehicle/marine vessel could be enhanced. In particular, we exploit a sensor fusion-based algorithm for the guidance system to perform UAV localization, whilst a control method based upon trajectory optimization is integrated. Indoor and outdoor experiments are conducted and the result shows that a precise autonomous landing on a 43 X 43 cm platform could be performed.

Soft-Core architecture for Analogue to Digital Converter (ADC) sampling is useful for mixed signal applications. Soft-core architecture for cutting edge odd or even ADC sampling with interface to block RAM memory has not been found. Soft-core architecture as a concept has become popular due to the advantage of customization for different applications as compared to general-core architecture suited for single application. The latest generation of piece wise sampling is odd sampling and was introduced in the second decade of the 20th century. Odd and even order sampling techniques are analogue in nature driven by a tuned (tuned for odd or even) mixer. This paper proposes a third-generation piece wise sampling with soft-core architecture that enables an option to select both odd and even while interfacing to memory mapping. The proposed odd/even has superior SNR performance of 6 dB as compared to existing architecture such as Mod-∆ which recorded worst performance of 18 dB. Advances in soft-core technology have allowed a niche odd/even switching field to be identified and studied, the study has also been extended to include memory architecture.

Considerable attention has been given to the research field of bioorganometallic chemistry, which is a hybrid chemistry field between biology and organometallic chemistry. The introduction of biomolecules, which have hydrogen bonding sites and chiral centers, into organometallic compounds is considered to be a promising strategy to construct chirality-organized bioorganometallic conjugates. This feature paper sketches an outline of induction of helical chirality into bioorganometallic conjugates. Topics covered include control of the helical chirality of 1,n’-disubstituted ferrocene moieties in ferrocene-dipeptide conjugates and the chirality induction of the Au(I)–Au(I) axis in the dinuclear organogold(I)-uracil conjugates.

Based on the Expected Utility Theory and Regret Theory, the Extended Regret Theory (ERT) is proposed in this paper to study the optimal pricing strategy of retailers in e-commerce environment. Taking the diversity of sales channels and the uncertainty of consumers in e-commerce environment into consideration, author of the paper designs an extended regret utility function which comprehensively considers both pessimistic and optimistic attitudes of decision makers in retailing industry to describe their regret-avoidance behavior. According to the sensitivity analysis, it is found that the optimal retail price decreases as the consumer price sensitivity coefficient increases, yet does not show variation with changes of the consumers pessimism degree. Moreover, the optimal retail price(s) obtained under EUT, ERT and combination of EUT and ERT represent the same.

Progression of oral squamous cell carcinoma (OSCC) has been associated with an escape of tumor cells from the host immune surveillance with growing evidence of its underlying molecular mechanisms and its interaction with the immune cell control. In this study the expression of HLA class I (HLA-I) antigens and of components of the antigen processing machinery (APM) was analyzed in 160 consecutive human papilloma virus (HPV)-negative OSCC lesions and correlated to tumor specific parameters, the intratumoral immune cell response and to the patients outcome. A heterogeneous, but predominantly lower constitutive protein expression of HLA-I APM components was seen in OSCC sections when compared to non-neoplastic cells. Based on the expression levels of HLA-I APM components three main OSCC subgroups were detected and categorized into HLA-Ihigh/APMhigh, HLA-Ilow/APMlow and HLA-Idiscordant high/low/APMhigh phenotypes. In the HLA-Ihigh/APMhigh group, the highest frequency of intratumoral CD8+ T cells and lowest number of CD8+ T cells close to FoxP3 cells was found. Despite being associated with the highest T cell infiltration, patients within this group presented the most unfavorable survival, which was most evident in stage T2 tumors. Thus, the presented findings strongly indicate the presence of additional factors involved in the immunomodulatory process of HPV-negative OSCC with a possible tumor-burden-dependent complex network of immune escape mechanisms beyond HLA-I/APM components and T cell infiltration in this tumor entity.

The main ideas of F-transform came from representing expert rules. It would be therefore re reasonable to expect that the more accurately the membership functions describe human reasoning, the more efficient will be the corresponding F-transform formulas. We know that an adequate description of our reasoning corresponds to complicated membership functions -- however, somewhat surprisingly, most efficient applications of F-transform use the simplest possible triangular membership functions. There exist some explanations for this phenomenon which are based on local behavior of the signal. In this paper, we supplement this local explanation by a global one: namely, we prove that triangular membership functions are the only one that provide the accurate description of appropriate global characteristics of the signal.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

This paper mainly analyzes the design and control of the rotational inverted pendulum, and presents a state space expression. Since the system is highly unstable a feedback control system is used. Augmentations with weighting functions based mixed sensetivity and H2 optimal control methods are used to make the system stable for uprise position. The rotational inverted pendulum have been simulated and compared with the proposed controllers and a promising results have been analyzed sussesfuly.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

A good management of diabetes requires at the same time self-regulation behaviour and a balanced involvement of family components. This study’s aims were: understanding fear of injections and perceptions of family conflicts in preadolescents and adolescents with type 1 diabetes mellitus and their mothers, comparing their perceptions, and identifying the risk factors impacting patients’ quality of life. Participants were one hundred and two patients (Mean age = 14.63, SD = 2.43; age range = 10-19 years; Females = 52) and their mothers (Mean age = 46.94, SD = 6.2, age range = 27-63 years), who filled in self and proxy-report questionnaires. Twenty % of patients and 14.7% of their mothers reported clinical score for fear of self-injection and blood testing. Mothers reported higher fear of injecting and family conflicts compared with the patients. Age, fear of injecting and family conflicts impacted significantly on patients’ quality of life perceptions. Clinical consideration and recommendations are given basing on the empirical results.

The present work studies a swelling porous-elastic system with viscoelastic damping. We establish a general and optimal decay estimate which generalizes some recent results in the literature. Our result is established without imposing the usual equal-wave-speed condition associated with similar problems in literature.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

— In a smart healthcare system," Human Activity Recognition (HAR)" is considered as an efficient approach in pervasive computing from activity sensor readings. The "Ambient Assisted Living (AAL)" in the home or community helps the people to provide independent care and enhanced living quality. However, many AAL models are restricted to multiple factors that include both the computational cost and system complexity. Moreover, the HAR concept has more relevance because of its applications, such as content-based video search, sports play analysis, crowd behavior prediction systems, patient monitoring systems, and surveillance systems. This paper attempts to implement the HAR system using a popular deep learning algorithm, namely "Recurrent Neural Network (RNN)" with the activity data collected from smart activity sensors over time, and it is publicly available in the "UC Irvine Machine Learning Repository (UCI)". The proposed model involves three processes: (1) data collection, (b) optimal feature learning, and (c) activity recognition. The data gathered from the benchmark repository was initially subjected to optimal feature selection that helped to select the most significant features. The proposed optimal feature selection method is based on a new meta-heuristic algorithm called "Colliding Bodies Optimization (CBO)". An objective function derived from the recognition accuracy has been used for accomplishing the optimal feature selection. The proposed model on the concerned benchmark dataset outperformed the conventional models with enhanced performance.

Modern gas turbines firing temperatures (1500-2000K) are well beyond the maximum allowable blade material temperatures. Continuous safe operation is made possible by cooling the HP turbine first stages -nozzle vanes and rotor blades- with a portion of the compressor discharge air, a practice that induces a penalty on the cycle thermal efficiency. Therefore, a current issue is to investigate the real advantage, technical and economical, of raising maximum temperatures much further beyond current values. In this paper, process simulations of a gas turbine are performed to assess HP turbine first-stage cooling effects on cycle performance. A new simplified and properly streamlined model is proposed for the non-adiabatic expansion of the hot gas mixed with the cooling air within the blade passage, which allows for a comparison of several cycle configurations at different TIT (turbine inlet temperature) and max (total turbine expansion ratio) with a realistically acceptable degree of approximation.. The calculations suggest that, at a given max, the TIT can be increased in order to reach higher cycle efficiency up to a limit imposed by the required amount and temperature of the cooling air. Beyond this limit, no significant gains in thermal efficiency are obtained by adopting higher max and/or increasing the TIT, so that it is convenient in terms of cycle performance to design at lower rather than higher max. The small penalty on cycle efficiency is compensated by lower plant cost. The results of our model agree with those of some previous much more complex and computationally expensive studies, so that the novelty of this paper lies in the original method adopted on which the proposed model is based, and in the fast, accurate and low resource intensity of the corresponding numerical procedure: all advantages that can be crucial for industry needs. The presented analysis is purely thermodynamic, with no investigation on the effects of the different configurations on plant costs, so that future work addressing a thermo-economic analysis of the air-cooled gas turbine power plant is the next logical step.