This study addresses the prediction of recurring failures in water supply networks, a complex and costly task, but essential for the effective maintenance of these vital infrastructures. Using historical failure data provided by Companhia de Água e Esgotos da Paraíba (CAGEPA), the research focuses on predicting the time until the next failure at specific points in the network. The authors divided the failures into two categories: Occurrences of New Faults (ONF) and Recurrences of Faults (RF). To make the predictions, they used predictive models based on Machine Learning, more specifically on MLP (Multi Layer Perceptron) neural networks. The study revealed that, by analyzing data from past failures and considering factors such as altitude, number of failures on the same street and days between failures, it is possible to achieve an accuracy greater than 80% in predicting failures within a 90-day interval. This demonstrates the feasibility of using fault history to predict future water supply outages with significant accuracy. These forecasts allow water utilities to plan and optimize their maintenance, minimizing inconvenience and losses. The article contributes to the field of water infrastructure management by suggesting that the data-driven approach can be applied in other cities or in networks of different types, such as energy or communication networks. The conclusions highlight the importance of data collection and analysis in preventing failures and optimizing water utilities’ resources.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

This study develops a progressive optimal fault-tolerant control method based on insufficient fault information. By combining passive and active fault-tolerant control manners during the process of fault diagnosis, insufficient fault information is fully used, and optimal fault-tolerant control effect is achieved. In addition, the fault-tolerant control method based on guaranteed robust cost control is introduced. The proposed progressive optimal fault-tolerant control method considers two aspects. First, as the amount of fault information continually increases, the performance index of the progressive optimal fault-tolerant controller improves. Second, at each moment, based on the corresponding insufficient fault information and prior knowledge, optimal fault-tolerant control is achieved according to current fault information. The process of progressive optimal fault-tolerant control converges to active fault-tolerant control when the fault is completely identified and the optimal fault-tolerant controller is no longer reconfigured until no more useful fault information can be provided. Furthermore, a progressive optimal fault-tolerant control algorithm based on the grid segmentation in the parameter uncertainty domain and the selection of different auxiliary center points is introduced. The simulation results verify the feasibility of the proposed algorithm and the validity of the proposed theory.

In order to solve the problem of fault diagnosis for CNC machine feed system under the condition of variable speed conditions, an intelligent fault diagnosis method based on multi-domain feature extraction and ensemble learning model is proposed. First, various monitoring signals including vibration signal, noise signal and current signal are collected. Then, the monitoring signals are preprocessed and the time-domain, frequency-domain and time-frequency domain feature indexes are extracted to construct a multi-dimensional mixed domain feature set. Finally, the feature set is putting into the constructed DoubleEnsemble-LightGBM model to realize the fault diagnosis of the feed system. The experimental results show that the model can achieve good diagnosis results under different working conditions for both the public data set and the feed system test bench data set, and the average overall accuracy is 91.07% and 98.06% respectively. Compared with XGBoost and other advanced ensemble learning models, the method has better accuracy. It provides technical support for the stable operation and intelligent of CNC machine tools..

Ensuring optimal performance and reliability in rotor-bearing systems is crucial for industrial applications. Imbalance and shaft bow in these systems can lead to decreased efficiency and increased vibrations. Early detection and mitigation of a rotor’s faults are essential, and model-based fault identification has gained much attention in the manufacturing industry for years. Over the past two decades, however, the development of fault diagnosis rules with data-driven and artificial intelligence (AI) has become a trend, and in the foreseeable future, AI combined with big data will become mainstream. Nevertheless, the critical role of rotating machinery in manufacturing introduces a challenge, as the availability of fault data is often insufficient. This limitation renders the establishment of diagnostic rules using data-driven methods and AI technologies impractical. In light of these challenges, this study proposes a novel hybrid approach, that combines a physical model with machine learning (ML) techniques for the diagnosis of multi-faults (imbalance and shaft-bow demonstrated) in a Jeffcott rotor. To overcome the lack of real-world faulted, labeled datasets, a physics-based Jeffcott rotor model is first derived and then used to generate abundant fault datasets for ML. Subsequently, simulated data are employed for the training of an artificial neural network (ANN), enabling the network to learn from and analyze the vast array of generated data. The results prove that a well-trained feed-forward neural network (FNN) can accurately isolate and diagnose the imbalance and shaft-bow faults using the simulated data and the real data from the Jeffcott rotor experiment. These physics-based and ML approaches prove effective particularly for multi-fault, offering new possibilities for advanced rotor system monitoring and maintenance strategies in industrial applications.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

The outstanding occurrences of red wood ant nests (RWA; Formica rufa-group) at two study sites in the Oberpfalz, NE Bavaria, Germany, could be confirmed by the 2023 re-inventory (a total of 5,393 nests and an increase by ≈8 %). RWA nests preferred mature and medium mature pine-dominated forests. Standing and downed dead wood do not negatively influence nests. Nest counts with woodpecker cavities and the diversity of the herb layer increased. The highly clustered nests in NW-SE direction suggests a strong interaction between nests distributions and the tectonic environment. Our developed (re-)inventory approach in combination with the comprehensive photo database is a valuable tool for a) monitoring the entire forest habitat including woodpecker cavities and dead wood in, at and around nests, and b) identifying GeoBio-Interactions. Such a comprehensive approach leads to more accurate and realistic counts of RWA nests during (re-)inventories and provides scientific evidence of the status quo of RWA occurrence. Our results disproved the unfounded and scientifically unsubstantiated blanket statement by laymen of the ASW Landesverband Bayern e.V. that RWA nest numbers in the Oberpfalz or even in the entire Bavaria are in sharp decline. We suggest seven to eight years as a suitable time interval for re-inventories.

The Sanaga River Valley is a deep-seated structure of about 220 km in width, bounded on its northern and southern sides by 025-0550 fault zones. Its internal structure has been very little described before this study. It is characterized by the presence of surface features where a thick stratum of shale and argillaceous sandstones have been documented. The use of electrical resistivity tomography for near-surface imaging and hydrogeological prospecting within shale succession is widespread. However, several methods of spatial modeling of resistivity contours are generally proposed for the interpretation of inverse resistivity model sections. To determine the most appropriate method for interpreting resistivity tomographies in the context of subsoil marked by significant heterogeneity, logarithmic contour intervals, and linear contour interval processing were implemented on data collected over five areas. The data consists of outcrops data, cuttings samples from groundwater boreholes, and resistivity sections ranging in length from 240 to 1000 m. Well-control of the inverse resistivity model sections derived from both processes shows that the linear contour intervals modeling gives a more realistic picture of the reservoir size of the wa-ter-bearing sand in both shale and argillaceous sandstone succession. The sedimentary architecture over Sanaga fault breccia is marked by vertical intrusion anomalies up to 80 m high. The shape of these anomalies, as well as the very low resistivity values that characterize them, suggests that they could be related to mud intrusion.

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude <6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

To enhance the overall reliability of the power system, engineers have redirected their focus toward health monitoring and early detection of faults in transformers. Among these faults, transformer core defects demand particular attention. While fault simulation using software has traditionally been the preferred approach, these methods suffer from data inaccuracies in real-world conditions. Consequently, conducting actual experimental setups with induced faults is imperative to investigate core issues. This study uses Hilbert Transform (HT) as a signal processing technique to extract crucial data characteristics, thereby enhancing the performance of the classifier model. The research involves analyzing electric current signals from a single-phase 1kVA transformer. A comparative assessment of our proposed model was conducted using raw data and Fast Fourier Transform (FFT), evaluating accuracy, precision, recall, F1-score, and computational time. The results demonstrate a significant improvement in all metrics for the classifier models, particularly the k-nearest neighbor (KNN) algorithm, which exhibited values of 83.89%, 84.39%, 83.89%, 83.79%, and 0.0156 seconds, respectively. Future work aims to extend this analysis under different loading conditions.

The operation of transformers suffers from natural or man-made disasters, subjecting the equipment to prolonged exposure to temperature, lightning strikes, transient over-voltages, and over-current, gradually producing insulation aging phenomenon, which results in partial discharges within the transformer. Without dealing with it beforehand properly, it may lead to insulation breakdown. Nowadays, with the mature development of microchip control technology and wireless communication technology, which is helpful for realizing the research for online real-time and long-term monitoring capabilities for power equipment. A transformer operating condition monitoring and diagnostic system that can rapidly and effectively prevent the breakdown of transformer insulation, which can impact the overall power supply system is developed in this paper. The system is divided into two parts based on its function. The first part is the operating condition monitoring and real-time alert unit for the transformer, primarily composed of an embedded computing module, a sensor module, and a transmission module. Its work content is to capture real-time online partial discharge ultrasonic signals and high frequency current comparator pulse signals, and analyze and determine the condition of the internal insulation and operational status whether it is fault or not. The second part is the central control unit, consisting mainly of an industrial computer and a transmission module. Its work content is to store the ultrasonic and high frequency current comparator pulse signals from the transformer operation monitoring and real-time alert unit. It uses the software to eliminate signal noise and interference, and then utilizes artificial neural networks to identify the type of fault. In this paper, the research for the phenomenon of insulation degradation in transformer equipment aims to establish aging trend profiles through the dual malfunctioning alert and aging process analysis, as well as the long-term measurement of ultrasonic signals from partial discharges and high-frequency current comparator pulse signals. This approach provides crucial reference data and a foundation for disposable on-site measurement, assessing the phenomenon of insulation aging stages, defects and damage of the transformers effectively. It allows for timely replacement or maintenance in advance, achieving the prevention of malfunctioning and predictive diagnosis of aging.

Power grid fault diagnosis technology has been widely used at home and abroad. With the access of distributed power sources and diversified loads, the distribution network has changed from a passive network to an active network, and the current has changed from "one-way" to "two-way". The structure of distribution network, equipment environment and operating conditions are becoming more and more complex, and the fault diagnosis and localization of active distribution network is becoming more and more difficult. With the rapid development of artificial intelligence, power grid fault diagnosis based on intelligence is unprecedented. This paper introduces the research status of distributed photovoltaic grid-connected fault diagnosis technology, and expounds the history of fault diagnosis technology, which mainly includes expert system, artificial neural network, Bayesian network, fuzzy set theory, rough set theory, Petri net analytical model and multi-source information fusion, etc. The applicability and characteristics of these diagnoses are described, and the existing defects and the overall direction of improvement are briefly described Finally, the key technical problems and future directions in the field of power system fault diagnosis are pointed out by combining theory with practice, so as to promote the further development of this field.

It is necessary to manage the power consumption and use fault-tolerance techniques to meet high reliability in Real-Time Embedded Systems, . Hence, in recent years, this is the main reason for providing an ideal approach to decrease power consumption through the worst-case behavior of instantaneous power management (peak-power management), while observing the Thermal Design Power (TDP). Although the multi-core chips in real-time embedded systems provide great opportunity for implementation of Two-phase Triple modular redundancy to meet high reliability, the energy overhead management of concurrently executing tasks is one of the challenges facing designers. In this article, we propose a scheme named Permanent Fault Aware, Two-Phase Peak-Power Management (PFA-TP3M), for scheduling real-time tasks in multi-core systems to eliminate peak power overlap from concurrent running tasks to maintain peak power consumption at the chip TDP. and through mapping different parts of each task on separate cores, prevents consecutive conflicts on cores, which have faced permanent faults to design the fault-tolerant system. Our simulation results show that our proposed scheme provides up to 700x fault tolerance increase (630x on average) compared to the state-of-the-art power management algorithm, an achievement costs up to 14%. (average 11%) increase the length of the task graph compared to it.

The Konya Closed Basin (Quaternary, Central Turkey) is a graben basin which expands toward the east-west and it is controlled by faults on three sides: The Konya fault zone in the west, the Divanlar fault zone in the east and the Karaömerler fault zone in the north. Calcretes developed in relation to fault systems in the Konya region are concentrated in areas where faults cut Quaternary aged terrestrial deposits. In this study, it is aimed to elucidate the deposition conditions, geochemistry and age (with ESR method) of the calcareous deposits associated with faults in the Konya Closed Basin. Calcretes in the region existing as coatings, dust, nodules and layers are in the form of dolocrete and clayey calcrete. Dolocretes were deposited in the Quaternary terrestrial sediments on the ophiolitic rocks and geochemical data point to an ultramafic source. Bacterial community, clay, quartz minerals and calcite cement are observed in the calcretes formed in areas with limestone basement. According to the results of ICP-MS analysis of samples taken from Konya calcretes, the %MgO contents are between 0.99 and 7.7; CaO%: between 34.71 and 50.71; %SiO2 between 3.22 and 20.59. %MgO in dolocretes are between 11.65 and 21.01; %CaO between 8.44 and 29.57; %SiO2 values between 4.48 and 9.17 The δ13C and δ18O isotope values of calcretes range from -3.87 to -7.62 and from -3.62 to -7.45 respectfully. Average δ13C values indicate that calcrete formation took place under pedogenic condition or in shallow groundwater. The calcretes deposited in 3 locations around the city of Konya (on the Konya fault zone) were dated by using the Electron Spin Resonance (ESR) method and ages between 217.47 and 389.85 ky were obtained. The calcrete samples taken from the fault planes (dip-slip normal fault bordering the Upper Cretaceous Ophiolitic Mélange and the Quaternary Karahüyük Formation) gave a relative age for faulting as being 292.86 ky. This first dating study conducted in the Konya Fault Zone has provided important clues to elucidate the formation history of Konya Closed Basin (KCB) and the paleo-seismological past of Konya.

This research presents a novel Customised Load Adaptive Framework (CLAF) for fault classifica-tion in Induction Motors (IMs), utilizing the Machinery Fault Prevention Technology (MFPT) Bearing Dataset. CLAF represents a pioneering approach that extends traditional fault classification methodologies by accounting for load variations and dataset customization. Through a meticulous two-phase process, it unveils load-dependent fault subclasses that have not been readily identified in traditional approaches. Additionally, new classes are created to accommodate the dataset's unique characteristics. Phase 1 involves the exploration of load-dependent patterns in time and frequency domain features using one-way Analysis of Variance (ANOVA) ranking and validation via bagged tree classifiers. In Phase 2, CLAF is applied to identify mild, moderate, and severe load-dependent fault subclasses through optimal Continuous Wavelet Transform (CWT) selection through Wavelet Singular Entropy (WSE) and CWT energy analysis. The results are compelling, with a 96.3% classification accuracy achieved when employing a wide neural network to classify proposed load-dependent fault subclasses. This underscores the practical value of CLAF in en-hancing fault diagnosis in IMs and its future potential in advancing IM condition monitoring.

A key component for the proper functioning, availability, and reliability of power grids is the power trans- former. Although these are very reliable assets, the early detection of incipient degradation mechanisms are very important to prevent failures that may shorten their lifetime. In this work a review and comparative analysis, of classical Machine Learning algorithms (such as single and ensemble classification algorithms) and two automatic machine learning classifiers, are presented for the fault diagnosis of power transformers. The goal is to determine whether fully automated ML approaches are worse or better than traditional ML frameworks that require a human in the loop (such as a data scientist) to identify transformer faults from oil-dissolved gases data. The methodology uses a DB compiled from published and proprietary transformer fault samples. Faults data is obtained from the literature, the Duval pentagon method, and user-expert knowledge. The parameters from, either single or ensemble classifiers, were optimized through standard machine learning procedures. The results showed that the best performing algorithm is a robust automatic machine learning classifiers model followed by classical algorithms such as neural networks and stacking ensembles. These results highlight the ability of a robust automatic machine learning model for, handling imbalanced power transformers faults datasets with high accuracy, using the minimum tuning effort by the electrical experts. By providing the most probable transformer fault condition will reduce the time required to find and solve the fault.

Availability and continuous operation under critical conditions are very important in electric machine drive systems. However, such systems, are suffering from several type of failures that affect the electric machine or the associated voltage source inverter. Therefore, fault diagnosis and fault tolerance are highly required. This paper presents a new robust deep learning-based approach to diagnosis multiple open-circuit fault in three phase two level voltage source inverter for induction motor drive applications. The proposed approach uses fault diagnosis variables obtained from sigmoid transformation of the motor stator currents. The open-circuit fault diagnosis variables are then introduced to a Bidirectional Long Short-Term Memory algorithm to detect the faulty switch(es). Several simulation and experimental results are presented to show the proposed fault diagnosis algorithm effectiveness and robustness.

In large-scale parallel computing and communication systems, an interconnect network structure is usually modeled as a graph, in which vertices and edges correspond to processors and communication links, respectively. In a graph, the vertices and edges are likely to fail, so we must think about the fault tolerance of a graph. Connectivity is an important parameter in the study of faulty tolerance for a graph. In this paper, we study a special class of connectivity: $m$-component connectivity, this is a natural generalization of the classical connectivity of graphs defined in terms of the minimum vertex-cut. Let $F$ is a vertex set of $G$ $(i.e, F\subseteq V(G))$, if the following conditions are satisfied, we say $F$ is a $m$-component cut: $(1)$ $G-F$ is disconnected; $(2)$ the number of components in $G-F$ is greater than or equal to $m$. In another word, the $m$-component connectivity $c\kappa_{m}(G)$ is defined as $min\{|F|~|~F\subseteq V(G)$ and $F$ is a $m$-component cut$\}$. Determining $m$-component connectivity is still unsolved in most interconnection networks even for small $m'$s. Leaf-sort graph is a special Cayley graph, it has many special properties that are different from other Cayley graphs. So we need to pay attention to some of it's special properties when we study it. In this paper, we can get the values: $c\kappa_{3}(CF_{n})=3n-6$ $(n$ is odd$)$ and $c\kappa_{3}(CF_{n})=3n-7$ $(n$ is even$)$ for $n\geq3$; $c\kappa_{4}(CF_{n})=\frac{9n-21}{2}$ $(n$ is odd$)$ and $c\kappa_{4}(CF_{n})=\frac{9n-24}{2}$ $(n$ is even$)$ for $n\geq4$; $c\kappa_{5}(CF_{n})=6n-16$ $(n$ is odd$)$ and $c\kappa_{5}(CF_{n})=6n-18$ $(n$ is even$)$ for $n\geq5$.

Energy supply interruptions or blackouts caused by faults in power distribution feeders entail several damages to power utilities and consumer units: financial losses, damage to power distribution reliability, power quality deterioration, etc. Most studies in the specialized literature concerning faults in power distribution systems present methodologies for detecting, classifying, and locating faults after their occurrence. In contrast, this study aims to prevent faults by estimating the city regions whose power grid is most vulnerable to them. This work incorporates the geographic space study to prevent faults in the distribution power grid through a spatial data analysis using local variables that increase the fault risk in feeders in some city regions. Geographically weighted spatial analysis is applied to data aggregated by regions to produce thematic maps with the city regions whose feeders are more vulnerable to failures. Spatial data analysis is developed in QGIS and R programming environments. It is applied in real data of electrical discharges in a medium-sized city with approximately 200,000 inhabitants. In this study, we highlight a moderate positive correlation between electrical discharge density and the percentage of faults in transformers by regions in the central and western areas of the city under study.

The $k$-set tree connectivity, as a natural extension of classical connectivity, is a very important index to evaluate the fault-tolerance of interconnection networks. Let $G=(V, E)$ be a connected graph and a subset $S\subseteq V$, an $S$-tree of graph $G$ is a tree $T=(V',E')$ that contains all the vertices of $S$. Two $S$-trees $T$ and $T'$ are internally disjoint if and only if $E(T)\cap E(T')=\varnothing$ and $V(T)\cap V(T')=S$. The cardinality of maximum internally disjoint $S$-trees is defined as $\kappa_{G}(S)$, and the $k$-set tree connectivity is defined by $\kappa_{k}(G)=\min\{\kappa_{G}(S)|S\subseteq V(G)\ \text{and} \ |S|=k\}$. In this paper, we show that the $k$-set tree connectivity of hierarchical folded hypercube when $k=4$, that is, $\kappa_{4}(HFQ_{n})=n+1$, where $HFQ_{n}$ is hierarchical folded hypercube for $n\geq 7$.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Process safety plays a vital role in the modern process industry. To prevent undesired accidents caused by malfunctions or other disturbances in complex industrial processes, considerable attention has been paid to data-driven fault detection techniques. To explore the underlying manifold structure, manifold learning methods including Laplacian eigenmaps, locally linear embedding, and Hessian eigenmaps have been utilized in data-driven fault detection. However, only the partial local structure information is extracted from the aforementioned methods. In this paper, these typical manifold learning methods are synthesized to find the underlying manifold structure from different angles. A more comprehensive local structure is discovered under a unified framework by constructing an objection optimization function for dimension reduction of the process data. The proposed method takes advantage of different manifold learning methods. Based on the proposed dimension reduction method, a new data-driven fault detection method is developed. Hotelling’s T2 and Q statistics are established for the purpose of fault detection. Experiments on an industrial benchmark Tennessee Eastman process and a real blast furnace ironmaking process are carried out to demonstrate the superiority and effectiveness of the proposed method.

Due to the broadening of services from industrial enterprises to customers, the industrial network has gained more significance than what is really thought. As a part of this revolution, this paper tried to introduce the best suitable routing option for the healthcare, banking and internet services industries to optimize the routing department of their enterprises. RIP is not associated with this study, being out of favor in the industries due to hop count limitation. The idea behind doing such a thing is to avoid improper implantation of routing inside the enterprises which causes lack of optimization in routing department. The method which is selected for this paper is qualitative case study of banking, healthcare and internet services industries with unstructured interviews of IT experts of the respected industries in an open-ended questions fashion. The results were illustrated based on the stories and the discussion of the stories is the main contributor to the result of the study. The evaluation results of the stories have illustrated, that EIGRP is a suitable routing option for health care and banking, while OSPF can be suitable for the internet services industry. The implication of the study can be optimized network of industries such as healthcare, banking and internet services and it introduces the best suitable routing option for the demanded industries with the case study method and narrative analysis of the stories, which start from load balancing type and ends to demanded routing protocol, while reaching to demanded routing protocol, it introduces the best suitable routing option of that industry

Recently, the triple-network convergence system (TNCS) has emerged from the deep integration of the power grid, transportation network, and information network. Fault recovery research in the TNCS is important since this system's complexity and interactivity can expand the faults scale and increase faults impact. Currently, fault recovery focuses primarily on single power grids and cyber-physical systems, but there are certain shortcomings, such as ignoring uncertainties including generator start-up failures and the occurrence of new faults during recovery, energy supply-demand imbalances leading to system security issues and communication delay caused by network attacks. In this study, we propose a recovery method based on the improved TD3 algorithm, factoring in shortcomings of the existing research. Specifically, we establish a TNCS model to analyze interaction mechanisms and design a state matrix to represent the uncertainty changes in the TNCS, a negative reward to reflect the impact of unit start-up failures, a special reward to reflect the impact of communication delay and an improved Actor network update mechanism. Experimental results show that our method obtains the optimal recovery decisions, maximizes restoration benefit in power grid failure scenarios and demonstrates a strong resilience against communication delay caused by DoS attacks.

Keywords: Electrical power systems, Support vector machines, Random Forest, Machine learning, Wavelet transform, Transmission lines fault, Electrical power quality, Short circuit, Classification of faults, Localization of faults, Decision trees, Ensemble learning, K-nearest neighbors.

incipient fault diagnosis is particularly important in process industrial systems, as its early detection helps to prevent major accidents. Against this background, this study proposes a combined method of Mixed Kernel Principal Components Analysis and Dynamic Canonical Correlation Analysis (MK-DCCA). The robust generalization performance of this approach is demonstrated through experimental validation on a randomly generated dataset. Furthermore, Comparative experiments were conducted on a CSTR Simulink model, comparing the MK-DCCA method with DCCA and DCVA methods, demonstrating its excellent detection performance for incipient fault in nonlinear and dynamic system. Meanwhile, fault identification experiments were conducted, validating the high accuracy of fault identification method based on contribution. The experimental findings demonstrate that the method possesses a certain industrial significance and academic relevance.

A Mw7.8 earthquake struck Turkey on February 6, 2023, causing severe casualties and economic losses. This paper investigates the characteristics of strong ground motion and seismogenic fault of the earthquake. We collected and processed the strong ground motion records of 379 stations using Matlab, SeismoSignal and Surfer software, and obtained the peak ground acceleration (PGA) contour map. We analyzed the near-fault effect, the fault locking segment effect and the trampoline effect of the earthquake based on the spatial distribution of PGA, the fault geometry and slip distribution. We found that the earthquake generated a very strong ground motion concentration effect in the near-fault area, with the maximum PGA exceeding 2000cm/s2. However, the presence of fault locking segments influenced the spatial distribution of ground motion, resulting in four significant PGA high-value concentration areas at a local dislocation, a turning point and the end of the East Anatolian Fault. We also revealed for the first time the typical manifestation of the trampoline effect in this earthquake, which was characterized by a large vertical acceleration with the positive direction significantly larger than the negative direction. This paper provides an important reference for understanding the seismogenic mechanism, damage mode, characteristics and strong earthquake law of Turkey earthquake.

The construction of sustainable road and highway networks in the world, despite numerous feasibility, pre-feasibility and execution studies, are always confronted with the demands and vagaries of foreseeable and unforeseeable natural disasters. Studying cyclones, earthquakes, fracturing and landslide zones along roads is therefore a challenge for the sustainability of these infrastructures. In many countries around the world, the methods generally used for these studies are not only expensive and time-consuming, but the results obtained are not always efficient. This work examines whether Landsat 8 (with a high cloud level) and SRTM data can be used in both equatorial and coastal Central Africa zones to produce relevant mapping, locating fracture and landslide zones, in order to contribute not only to better road layout at lower cost and in a relatively short time, but also to better prevention of geological disasters that may occur on its network. To this end, a map of the main road network was produced and validated with field data, as well as the maps of the main unstable slopes, faults and fractures zones intersecting the road or highway network. These approaches are useful for sustainable planning, management, monitoring and extension of roads worldwide especially, in Central Africa.

As the demands in reliability and high-degree of automation in industrial applications are increasing exponentially, the current Industry 4.0 trend lies in migrating towards smarter technologies that increase flexibility and provide autonomous operation. To tackle this, manufacturers shifted towards Real-Time Ethernet communication which supports autonomous operation, faster sensor/actuator configuration and high degree of determinism. Nevertheless, the uninterrupted operating principle of legacy industrial systems as well as the system complexity and heterogeneity constitutes the transition to Real-Time Ethernet very challenging. This article proposes a novel method allowing to automate the generation of executable code for Real-Time Ethernet architectures based on high-level programming models. The method is based on a programming model and modular code artifacts for the hardware architecture, employing Real-Time Ethernet communication. Through an tool-supported algorithm the high-level model is linked to the architecture's communication primitives and interfaces. The tool-support reduces significantly the development and debugging effort for Real-Time Ethernet applications and increases the application reliability, since the generated code is based on verified programming models. Additionally, the tool creates dedicated files, which allow automated industrial network configuration without any human intervention. Finally, by embedding firewall policies into the code generation process, the method guarantees cyber-resilience for the Real-Time Ethernet architecture. We demonstrate the proposed method in Programmable Logic Controllers (PLCs) of a Public Power Corporation's Hydroelectric Power Plant, which control the temperature and rotor speed of a power generator. The results demonstrate the method's ability to generate rapidly trustworthy and fault-tolerant code for the autonomous plant operation. The hurdles in time and effort for developing, configuring and debugging Real-Time Ethernet applications can be minimized through a high-level programming model that allows automated generation of executable code that is reusable for similar applications. Such time and effort reduction may pave the way towards the Industry 4.0 area.

It is known that the source of a tectonic earthquake in the framework of the theory of elasticity and viscoelasticity is considered as a displacement along a certain fault surface. Usually, when describing the source, the geometry of the fault surface is simplified to a flat rectangular area. The displacement vector is assumed to be constant. In this paper, we propose a model of an earthquake source in the form of a displacement with a constant vector along a stochastic surface. A number of standard assumptions were made when modeling. We take into account only the elastic properties of the medium. We consider the Earth’s crust as a half-space and assume that the medium is homogeneous and isotropic. For the mathematical description of the earthquake source, we use the classical force equivalent of displacement along the fault. This is the distribution of double pairs of forces. The field of displacements under the action of body forces is found through a combination of Mindlin nuclei of strain. The paper presents solutions for strike-slip fault. To obtain a stochastic fault surface, we propose to introduce a random deformation of a rectangular flat surface. The paper presents the results of a computational experiment comparing the levels and regions of relative deformations of the Earth’s crust in the case of displacement along a flat rupture surface and along a stochastic one. In the case of a stochastic surface, the regions of relative deformations become asymmetric. The developed model will help to indirectly take into account various mechanical properties of the Earth’s crust when modeling deformations caused by earthquakes.

The process industry is confronted with rising demands for flexibility and efficiency. One way to achieve this are modular process plants that consist of pre-manufactured modules with their own decentralized intelligence. Plants are then composed of these modules as unchangeable building blocks and can be easily re-configured for different products. Condition monitoring of such plants is necessary, but available solutions are not applicable. The authors suggest an approach in which model-based symptoms are derived from few measurements and observers that are based on manufacturer knowledge. The comparisons of redundant observers lead to residuals that are classified to obtain symptoms. These symptoms can be communicated to the plant control and are inputs to an easily adaptable diagnosis. The implementation and validation at a modular mixing plant showcases the feasibility and the potential of this approach.

Detecting, especially locating local degradations at an incipient stage, is very important for mission-critical high voltage rotating machines. One particular challenge of the existing testing techniques is that the characteristic of a local incipient defect is not prominent due to various factors such as averaging with the healthy remainder, attenuation in signal propagation, interference, and varied operating conditions. This paper proposes and investigates the frequency domain reflectometry (FDR) technique based on scattering parameter measurement. The FDR result presents the object length, wave impedance, and reflections due to impedance discontinuity along the measured windings. Experiments were performed on two commercial coils with artificially made defects. These defects include turn-to-turn short, surface creepage, loose coils, and local overheating, which are commonly seen in practice. Two practical water pumps in the field were also selected for investigation. The study outcome shows that the FDR can identify and locate both structure and insulation degradations of both shielded and unshielded objects with good sensitivity. This makes the FDR a comprehensive tool for fault diagnosis and aging assessment.

Due to the complex underground environment, pumping machines are prone to produce numerous failures. The indicator diagrams of faults are similar in a certain degree, which produces indistinguishable samples. As the samples increases, manual diagnosis becomes difficult, which decreases the accuracy of fault diagnosis. For accurately and quickly judging the fault type, we propose an improved adaptive activation function and apply it to five types of neural networks. The adaptive activation function improves the negative semi-axis slope of the ReLU activation function by combining the gated channel conversion unit to improve the performance of the deep learning model. The proposed adaptive activation function is compared with the traditional activation function through the fault diagnosis data set and the public data set. The results show that the activation function has better nonlinearity, can improve the generalization performance of deep learning model, the accuracy of fault diagnosis. In addition, the proposed adaptive activation function can also be well embedded in other neural networks.

Most IoT systems meant for implementing mission-critical systems are multi-layered based. The majority of the computing is done in the services and gateway layer. The Gateway layer connects the Internal section of the IoT to the cloud through the Internet. The failure of any node between the services servers and the gateways will isolate the entire network leading to zero tolerance. A networking topology is required to connect the service servers to the gateways, yielding 100% fault tolerance. Empirical formulation of the model chosen to connect the service’s servers to gateways through routers is required to compute the fault tolerance of the network. Rectangular and Interstitial Mesh have been proposed in this paper to connect the service servers to the gateways through the servers that yield 0.999 fault tolerance of the IoT network. An empirical formulation is also presented using which the Fault tolerance of the IoT network can be computed. An enhancement of 11% in the fault tolerance capability of an IoT network has been achieved by implementing Rectangular and Interstitial Mesh in the gateway layer of the network.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

Fault detection in PV arrays and inverters is critical for ensuring maximum efficiency and performance. Artificial intelligence (AI) learning can be used to quickly identify issues, resulting in a sustainable environment with reduced downtime and maintenance costs. As the use of solar energy systems continues to grow, the need for reliable and efficient fault detection and diagnosis techniques becomes more critical. This paper presents a novel approach for fault detection in photovoltaic (PV) arrays and inverters, combining AI techniques. It integrates Elman Neural Network (ENN), Boosted Tree Algorithms (BTA), Multi-layer Perceptron (MLP), and Gaussian Processes Regression (GPR) for enhanced accuracy and reliability in fault diagnosis. It leverages their strengths for accuracy and reliability of fault diagnosis. Feature engineering-based sensitivity analysis was utilized for feature extraction, the fault detection and diagnosis were assessed using several statistical criteria including PBAIS, MAE, NSE, RMSE, and MAPE. Two intelligent learning scenarios are carried out, the first scenario is done for PV array fault detection with DC power (DCP) as output. The second scenario is done for inverter fault detection with AC power (ACP) as the output. The proposed technique is capable of detecting faults in PV arrays and inverters, providing a reliable solution for enhancing the performance and reliability of solar energy systems. Real-world solar energy dataset is used to evaluate the proposed technique, with results compared to existing detection techniques and obtained results show that it outperforms existing fault detection techniques, achieving higher accuracy and better performance. The GPR-M4 optimization justified reliably among all the models with MAPE=0.0393, and MAE=0.002 for inverter fault detection and MAPE=0.091, and MAE=0.000 for PV array fault detection.

Fault detection is an important step for subsurface interpretation and reservoir characterization from 3D seismic images. Due to the numerous and complicated faulting structures of seismic images, manual seismic interpretation is time taking and need intensive work. To overcome this problem, geoscientists are coming up with productive computer-aided techniques for assisting in interpreter science for many years. However, in this paper, we used a pre-trained CNN model to predict faults from the 3D seismic volume of the Poseidon field of Browse Basin, Australia. Basically, this field is highly structured with complex normal faulting throughout the targeted Plover Formations. So, our motivation for this work in this field is to compare machine learning-based fault prediction to user interpreted faults identification with supported by seismic variance attribute. We found very satisfying result using DL with having an improved fault probability volume that outperform variance technology. Therefore, we propose that this workflow could reduce time and able to predict fault quite accurately in any field area.

To address the problem of limited fault diagnosis accuracy in oil-immersed on-load tap changers (OLTC), this paper introduces a novel fault diagnosis method that combines the analysis of mechanical vibration signals and high-frequency current signals. The proposed approach aims to enhance the accuracy of fault diagnosis. To begin, an experimental platform is constructed to simulate the OLTC contact. Mechanical vibration signals and high-frequency current signals are collected from the testing platform under various operating states. These signals are then subjected to wavelet packet transform for denoising, followed by correlation analysis to capture the relationship between signals in different states. Based on these preliminary steps, the features of the signals are extracted and analyzed using ensemble empirical mode decomposition and the Hilbert-Huang transform. Subsequently, a support vector machine (SVM) is employed to analyze both the mechanical vibration signal and high-frequency current signal, enabling the classification of the OLTC contact state. The results demonstrate that the combination of characteristic analysis of mechanical vibration signals and high-frequency current signals provides a more comprehensive reflection of the actual OLTC contact state under different conditions. Through the SVM classification, the error between the predicted values and real values of the two types of signals remains below 10%, validating the efficiency and feasibility of the proposed method for fault diagnosis of OLTC contacts. These research findings serve as a reliable foundation for the diagnosis of operational states of on-site oil-immersed on-load tap changers, offering valuable insights for practical applications.

This paper presents an in-depth contextualized tutorial on Agricultural IoT (Agri-IoT), covering the fundamental concepts, assessment of routing architectures and protocols, and performance optimization techniques via systematic survey and synthesis of related literature. The negative impacts of climate change and the increasing global population on food security and unemployment threats have motivated the adoption of the wireless sensor network (WSN)-based Agri-IoT as an indispensable underlying technology in precision agriculture and greenhouses to improve food production capacities and quality. However, most related Agri-IoT testbed solutions have failed to achieve their performance expectations due to the lack of an in-depth and contextualized reference tutorial that provides a holistic overview of communication technologies, routing architectures, and performance optimization modalities based on users’ expectations. Thus, although IoT applications are founded on a common idea, each use case (e.g., Agri-IoT) varies based on specific performance and users expectations as well as its technological, architectural, and deployment requirements. Likewise, the agricultural setting is a unique and hostile area where conventional IoT technologies do not apply, hence the need for this tutorial. Consequently, this tutorial addresses these via the following contributions: (1) a systematic overview of the fundamental concepts, technologies, and architectural standards of WSN-based Agri-IoT, (2) an evaluation of the technical design requirements of a robust, location-independent, and affordable Agri-IoT, (3) a comprehensive survey of the benchmarking fault tolerance techniques, communication standards, routing and medium access control (MAC) protocols, and WSN-based Agri-IoT testbed solutions, and (4) an in-depth case study on how to design a self-healing, energy-efficient, affordable, adaptive, stable, autonomous, and cluster-based WSN-specific Agri-IoT from a proposed taxonomy of multi-objective optimization (MOO) metrics that can guarantee an optimized network performance. Furthermore, this tutorial established new taxonomies of faults, architectural layers, and MOO metrics for cluster-based Agri-IoT (CA-IoT) networks and a 3-tier objective framework with remedial measures for designing an efficient associated supervisory protocol for cluster-based Agri-IoT networks.

Redundancy in ship systems is provided to ensure operational resilience through equipment backups which ensures system availability and offline repairs of machinery. The electric power generation system of ships provides the most utility of all systems, hence is provided with good level of standby units to ensure reliable operations. Nonetheless, the occurrence of undesired black outs are common onboard ships and portends a serious danger to ship security and safety. Therefore, understanding the contributing factors affecting system reliability through component criticality analysis is essential to ensure a more robust maintenance and support platform for efficient ship operations. In this regard hybrid reliability and fault detection analysis were conducted to establish component criticality and related fault conditions. A case study was conducted on a ship power generation system consisting of 4 marine diesel power generation plants onboard an Offshore Patrol Vessel (OPV). Results from the reliability analysis indicate overall low system reliability of less than 70 per cent within the first 24 months of the 78 operational months. Component criticality using reliability importance measures was used to identify all components with more than 40 per cent contribution to sub systems failure. Additionally, machine learning was used to aid the reliability analysis through feature engineering and fault identification using Artificial Neural Networks classification. The ANN has identified failure patten threshold at about 200kva which can be attributed to overheating, hence establishing link between component failure and generator performance.

The stator winding insulation system is the most critical and weak part of the EMU's (electric multiple unit) traction motor. The effective diagnosis for stator ITSC (inter-turn short-circuit) faults can prevent the fault from expanding into phase-to-phase or ground short-circuits. The TCU(traction control unit) controls the traction inverter to output SPWM (sine pulse width modulation) excitation voltage when the traction motor is stationary. Three ITSC fault diagnostic conditions are based on different IGBTs control logic. The Goertzel algorithm is used to calculate the fundamental current amplitude difference Δi and phase angle difference Δθ of equivalent parallel windings under the three diagnostic conditions. The six parameters under the three diagnostic conditions are used as features to establish an ITSC fault diagnostic model based on random forest. The proposed method was validated using a simulation experimental platform for ITSC fault diagnosis of EMU traction motors. The experimental results indicate that the current amplitude features Δi and phase angle features Δθ change obviously with the increase of ITSC fault extent if the ITSC fault occurs at the equivalent parallel windings. The accuracy of the ITSC fault diagnosis model based on the random forest for ITSC fault detection and location both in train and test samples are 100%.

Future climate change is expected to affect components of the hydrological cycle. However geologic factors can sometimes be more important than the climate with regarding to change hydrological processes. The Keriya River is a large glacier-fed river in the western Tibet Plateau, its upper reaches flow across active fault zones, which have experienced four medium-sized earthquakes within four months 1974. These active faults have made difficult to identify normal meltwater changes using a snow-ice melt model. Because of the seismic events, the river has experienced substantial changes in their drainage systems and complex hydrological processes. Both the Mann-Kendall trend test and a correlation analysis were applied to detect the monthly patterns of stream flows, the change points and the correlations among both summer discharge and air temperature before and after seismic events. We found significant correlations between monthly air temperature and meltwater flow in the summer June during the pre-earthquake of 1958-1974, but none in July and August in the post-earthquake of 1975-1980, and we found no correlation following the earthquake. The correlations were the inverse by losing the former and setting up the latter alternately since the multiple earthquakes. Clearly, the earthquakes and changes in the faults can greatly induce hydrological processes.

Fault detection at the early stage of development is of great importance in the maintenance of electric motors. In this regard, Motor Current Signature Analysis (MCSA) is cited in many articles to detect rotor bar fracture. The popularity of MCSA is due to its non-invasive and non-destructive nature, simplicity, and, compatibility with several signal processing tools. The vast variety of the signal processing tools which are commonly used for detecting the broken rotor bar fault is based on the Fast Fourier Transform (FFT) of the stator current signal and analysis of the produced Fourier spectrum; however, because of the small amplitude at the fault frequency relative to the main frequency amplitude, the former cannot be easily discriminated from the latter. Therefore, the peak at the fault frequency is hidden in the shadow of the main frequency component, hence the fault will not be detectable. As a solution to vanish the base frequency component, a method based on the Algebraic Identity of trinomial expansion is proposed in this paper which enables us to display the difference between the frequency of the fault signature and the base frequency. In this article, the fault of the broken rotor bars of the squirrel cage induction motor is revealed by the proposed method. In addition, a frequency weighting technique is presented to magnify the component at the fault related frequency compared to the lower frequencies. To validate the proposed methods, they are examined on the laboratory data obtained from three different operating conditions including the direct online start, the direct torque control, and the scalar control and the results show the ability of the proposed methods in fault detection of an induction motor.

According to the structural features, sedimentary evolution, types of sedimentary facies, source rocks features, diagenesis evolution, reservoir features and hydrocarbon formation mechanism, exploration status and hydrocargon resource potential, this article analyzed the major control fac-tors and hydrocarbon distribution rules of the lithologic reservoirs in continental fault basin. The research shows that three major control factors and one coupled factor (fractures act as a tie) in-fluence hydrocarbon formation of lithologic traps in Nantun Formation of Tanan Sag, which in-clude sand body types, effective source rocks and effective reservoirs. With the increase in depth, enough hydrocarbon generate in source rock under thermal evolution. Hydrocarbon generation and expulsion are more intensive when it comes to the depth threshold and critical conditions of hydrocarbon supplying are met. Traps that surrounded or contacted by source rock, or communi-cated by fault are qualified to form reservoirs. As buried depth increases, hydrocarbon genera-tion-expulsion intensity grows and the trap is more petroliferous. Hydrocarbon accumulation and reservoir formation are also controlled by sandbody accumulation conditions. When it meets the critical conditions of hydrocarbon generation and concrete oil and gas are charged in, better phys-ical properties of sandbody always indicate more hydrocarbon accumulation in the trap. Alloca-tion of sand type, effective source rock and effective reservoir is optimized under the effect of fractures, and coupled hydrocarbon reservoir with these three elements.

In a complex working environment, the fault signal of the gearbox is greatly affected by the outside world, and fault feature recognition is difficult, so the fault diagnosis accuracy is difficult to meet the expected requirements. To solve this problem, this paper proposes a gearbox fault diagnosis method based on an optimized stacked denoising auto encoder (SDAE) and kernel extreme learning machine (KELM). Firstly, the Particle Swarm Optimization algorithm in Adaptive Weight (SAPSO) was adopted to optimize the SDAE network structure, and the number of hidden layer nodes, learning rate, noise addition ratio and iteration times were adaptively obtained to make SDAE obtain the best network structure. Then, the best SDAE network structure was used to extract the deep feature information of weak faults in the original signal. Finally, the extracted fault features are fed into KELM for fault classification. Experimental results show that, compared with existing commonly used methods of fault diagnosis, the fault diagnosis model proposed in this paper can reduce the influence of noise in the original signal can better learn the deep-level features in the original signal and has higher diagnosis accuracy, faster diagnosis speed and good generalization in fault diagnosis.

Safe, high-quality and economical electric energy transportation is the basic requirements of modern power system operation. Transformer, as one of the core equipment of power system and national grid system, has the characteristics of diverse types, variable models and wide deployment. It is the basic equipment for power system to realize voltage change and electric energy distribution. Because the power system transformer needs to operate with load for a long time, the probability of failure is usually higher than that of other power equipment in general. This paper starts from the transformer fault and fault diagnosis. Firstly, the transformer fault types, traditional transformer fault diagnosis techniques and the advantages of machine learning in transformer fault diagnosis are reviewed. Secondly, the application of information system theory and information entropy in transformer fault diagnosis is introduced. Then it introduces machine learning technology, feature selection and extraction technology in transformer fault diagnosis, and machine learning algorithms such as support vector machine and extreme learning machine for transformer fault diagnosis. Finally, the potential development trend of information system theory, information entropy and machine learning in transformer fault diagnosis is forecasted. The combination of transformer fault prediction and machine learning algorithm is helpful for power system maintenance personnel to accurately predict the running state of power equipment, and also provides a new method and technology for the safe and reliable operation and regular maintenance of power system.

When an aircraft malfunctions, quickly and accurately identifying the faulty unit is essential for ensuring normal operation. Unfortunately, maintenance engineers often struggle to acquire the necessary fault-related knowledge due to poor management and utilization of aircraft fault documents. To address this issue, we introduce knowledge graph technology into the field of aircraft fault diagnosis, exploring its construction and application for effective knowledge management. Our work starts by analyzing the critical knowledge elements required for aircraft fault diagnosis and designing a schema layer for fault knowledge graphs. We then we then combine deep learning and heuristic rules to extract fault knowledge from both structured and unstructured data, enabling the construction of aircraft fault knowledge graphs. Finally, we develop a fault question-answering system based on fault knowledge graphs that can accurately give solutions to questions posed by maintenance engineers. Our practice demonstrates that knowledge graphs provide an effective means of managing aircraft fault knowledge, assisting engineers in locating fault reasons accurately and quickly.

Abstract: The EMU(electric multiple units) traction motors are powered by converters. The PWM(pulse width modulation) voltage increases the voltage stress borne by the motor insulation system, making the ITSC(inter-turn short-circuit) fault more prominent. An index based on short-circuit thermal power was proposed in the article to evaluate the non-metallic ITSC faults degree. The apFFT(all phase FFT) time-shift phase difference correction with double Hanning-windows is used to calculate the fundamental frequency of the traction motor's ZSVC（zero se-quence voltage component）, the fundamental amplitudes of ZSVC and three-phase current. The five parameters are used as fault features to train the SVM (support vector machine)fault diagnosis model. The SVM hyper-parameters C and g are optimized by K-CV (K fold cross-validation) and grid search methods. The experimental verification was carried out by the EMU electric traction simulation experimental platform. According to the non-metallic degree index proposed in this article, the experimental samples were divided into three categories, normal, incipient and serious fault samples. The ITSC fault diagnosis accuracy was 100% on the training data set and 93.33 % on the test data set. There was no misclassification between normal and serious ITSC fault samples.

To realize the diagnosis of compound faults in gearboxes at different speeds, an "end-to-end" intelligent diagnosis method based on a deep neural network is proposed, named efficiency channel attention-capsule network (ECA-CN). First, the process uses a deep convolutional neural network to extract fault features from the collected raw vibration signals, then embeds the efficient channel attention module to filter important fault features, then uses the capsule network to vectorize the feature space information, and finally calculates the correlation between different levels of capsules by the dynamic routing algorithm to achieve accurate gearbox compound fault diagnosis. The effectiveness of the proposed ECA-CN fault diagnosis method was verified by the composite fault dataset of the 2009 PHM Challenge gearbox, with an average accuracy of 99.63% and a standard deviation of 0.22%. In the comparison experiments with the traditional fault diagnosis method, the average accuracy of the ECA-CN method was improved by 4.62%, and the standard deviation was reduced by 0.58%. The experimental results show that ECA-CN has a more competitive diagnostic performance.

Northeastern margin is a natural experimental field for studying crustal extrusion and expansion mechanism. Accurate crustal deformation pattern is a key point in the analysis of regional deformation mechanism and seismic hazard research and judgment. In this paper, the present-day GPS velocity field on the northeastern margin of the Tibetan Plateau was obtained from encrypted GPS observations around the Haiyuan-Liupanshan fault zone, combined with GPS observations on the northeastern margin of the Tibetan Plateau from 2010 to 2020. Firstly, we divided the study area into three relatively independent blocks: ORDOS block, Alxa block and Lanzhou block; secondly, the accurate fault distribution of the Haiyuan-Liupanshan fault zone was taken into account to obtain the optimal inversion model; finally, using the block and fault back-slip dislocation model, the inversion got the slip rate distribution, locking depth and slip deficit rate of each fault. The results indicate that the Laohushan Fault and Haiyuan Fault are dominated by left-lateral strike-slip, while the Liupanshan Fault is dominated by thrust dip-slip, and the Guguan-Baoji Fault has both left-lateral strike-slip and thrust dip-slip components. The maximum locking depths of the Laohushan Fault, Haiyuan Fault, Liupanshan Fault and Guguan-Baoji Fault are 5 km, 13 km, 15 km and 10 km respectively, and the locking of Haiyuan Fault is strong in the middle section and weak in the eastern and western section. The Haiyuan Fault is still in the post-earthquake stress adjustment stage. The slip deficit rate decays from 3.6 mm/yr to 1.8 mm/yr from west to east along the fault zone. Combined with geological and historical seismic data, the results suggest that the mid-long term seismic risk in the Liupanshan Fault is high.

Condition monitoring is today a crucial and unavoidable practice related to the use of widespread mechanical components as rolling element bearings. Despite the diffusion of new data-driven techniques to analyze vibrational signals and detect the state of health of the system, mathematical tools, deriving more or less directly from the Fourier transform and defined either on the time or the frequency domain or on a combination of them (i.e. signal-based techniques), remain still essential and irreplaceable in the light of the deep and detailed information they provide. In this paper the diagnostic efficacy of an ample spectrum of these methods is investigated, applying them to study faults occurrence in the first bearing dataset released by NASA IMS Center. Thanks to their analytical definition, which is formulated taking into consideration to some extent the mathematical nature of the signal, faults signatures can be clearly identified and their temporal development can be fully traced, confirming their ability as powerful means to constantly monitor the state of a system even in real-time applications.

In modern inverter applications, multilevel converters are used thanks to their capability of reducing the passive fi lter volumes, improving the overall THD, sharing the power sources across the several converter cells, and providing a reconfi guration ability in case of failure. However, increasing the number of cells makes more complex the control of the converter. This article proposes a decentralized control technique based on the use of elementary modular controllers, associated with each converter cell and communicating with their close neighbors to obtain the balancing of the powers they supplied. Each modular controller can be dynamically removed or added to allow reconfi guration of the converter for functional safety purpose. This method is applied to a 240V/3A 5-cells Cascaded Full-Bridge Multilevel Converter. The response of the system to load transients and cell voltage disturbances demonstrates the robustness of the proposed decentralized control method. Thanks to the use of modular controllers, the number of levels of the converter can be extended to the order N without adding complexity to its control.

Artificial intelligence systems are increasingly becoming a component of security-critical applications. The protection of such systems from various types of destructive influences is thus a relevant area of research. The vast majority of previously published works are aimed at reducing vulnerability to certain types of disturbances or implementing certain resilience properties. At the same time, the authors either do not consider the concept of resilience as such, or their understanding varies greatly. This work presents a formalized definition of resilience and its characteristics for artificial intelligence systems from a systemic point of view. It systematizes ideas and approaches to building resilience to various types of disturbances. Taxonomy of resilience of artificial intelligence systems to destructive disturbances is proposed. Approaches and technologies for complex protection of intelligent systems, issues of their resource efficiency and other open research issues are considered. Approaches of resilience assessment for artificial intelligence system are also analyzed and recommendations are provided for their implementation.

Blockchain technology has been gaining great interest from a variety of sectors including healthcare, supply chain, and cryptocurrencies. However, Blockchain suffers from its limited ability to scale (i.e. low throughput and high latency). Several solutions have been proposed to tackle this. In particular, sharding proved that it is one of the most promising solutions to Blockchain’s scalability issue. Sharding can be divided into two major categories: (1) Sharding-based Proof-of-Work (PoW) Blockchain protocols, and (2) Sharding-based Proof-of-Stake (PoS) Blockchain protocols. The two categories achieve good performances (i.e. good throughput with a reasonable latency), but raise security issues. This article focuses on the second category. In this paper, we start by introducing the key components of sharding-based PoS Blockchain protocols. Then, we briefly introduce two consensus mechanisms, namely PoS and practical Byzantine Fault Tolerance (pBFT), and discuss their use and limitations in the context of sharding-based Blockchain protocols. Next, we provide a probabilistic model to analyze the security of these protocols. More specifically, we compute the probability of committing a faulty block and measure the security by computing the number of years to fail. Finally, we evaluate the effectiveness of the proposed model via numerical analysis.

Las Loras UNESCO Global Geopark (UGGp) is geologically diverse, particularly in relation to water-derived features: springs, karst springs, travertine buildings, waterfalls, caves. In this work, the interactions between geology, geomorphology, structures and hydrogeology are analyzed. These four components are the fundamentals of geodiversity and their interactions provide a conceptual model of hydrogeological functioning at Las Loras UGGp. The most plausible hypothesis is that the system is formed by two superimposed aquifer systems, separated by an aquitard formed by Lower Cretaceous material. The deep lower aquifer formed by the Jurassic limestones only outcrops on the northern and southern edges of the Geopark and in a small arched band to the south of Aguilar de Campoo. It forms a basement subject to intense deformation. The upper aquifer system, formed by outcropping materials from the Upper Cretaceous, is a free aquifer. It is formed by a multilayered aquifer system that is highly compartmentalized by the very disturbed geomorphology of the landscape, constituting each moorland and each lora, an individualized recharge-discharge system. This model explains the base level of the rivers, the abundant number of existing springs and the permanent nature of some rivers, providing the keys to understand the bases of the geoconservation of a rich geological heritage linked to the active processes of the water cycle.

Blind deconvolution (BD) is one of the effective methods that help pre-process vibration signals and assist in bearing fault diagnosis. Currently, most BD methods design an optimization criterion and use frequency or time domain information independently to optimize a deconvolution filter. It recovers weak periodic impulses related to incipient faults. However, the random noise interference may cause the optimizer to overfit. The time-domain-based BD methods tend to extract fault-unrelated single peak impulse, and the frequency-domain-based BD methods tend to retain the maximum energy frequency component, which will lose the fault-related harmonics frequency components. To solve the above issue, we propose a hybrid criterion that combines the kurtosis for time domain optimization and the $G-l_1/l_2$ norm for the frequency domain. These two criteria are monotonically increasing and decreasing, so they mutually constrain to avoid overfitting. After that, we design a multi-task one-dimensional convolutional neural network with time and frequency branches to achieve an optimal solution for this hybrid criterion. The multi-task neural network realizes the simultaneous optimization of two domains. Experimental results show that our proposed method outperforms other state-of-the-art methods.

Centralized control algorithm limits the hardware flexibility of a Modular Multilevel Converter (MMC). Therefore, industrial MMC applications have started adopting distributed control structures. Even though distributed controller reduces a single point of failure risk compared to the centralized controller, the failure risk of the entire control systems increases due to the number of local controllers. However, the distributed controller can be programmed in such a way as to bypass the faulty local controller and take care of the power modules with the adjacent local controllers. This paper implements a modular distributed fault-tolerant controller for a scaled laboratory MMC prototype. Experimental results show that an MMC can operate without interruption, even under two local controller failures. Besides, the experimental results are verified with the Opal-RT, a real-time simulator with the same controller in a Control Hardware in Loop (CHIL) environment.

The electric power distribution utility is responsible for providing energy to consumers in a continuous and stable way, failures in the electrical power system reduce the reliability indexes of the grid, directly harming its performance. For this reason, there is a need for failure prediction to reestablish power in the shortest possible time. Considering an evaluation of the number of failures over time, this paper proposes to perform a failure prediction during the first year of the pandemic in Brazil (2020) to verify the feasibility of using time series forecasting models for fault prediction. The Long Short-Term Memory (LSTM) model will be evaluated to obtain a forecast result that can be used by the electric power utility to organize the maintenance teams. The Wavelet transform shows to be promising in improving the predictive ability of the LSTM, making the Wavelet LSTM model suitable for the study at hand. The results show that the proposed approach has better results regarding the evaluation of the error in prediction and has robustness when a statistical analysis is performed.

We investigated fault gases (helium, radon, CO₂) in two seismically active Cenozoic sedimentary environments: a) Meinweg (in 2015) at a tectonically quiet horst structure in the Lower Rhine Embayment and b) Bodanrück (in 2012; Lake of Constance) at the Molasse Basin and part of the Freiburg–Bonndorf–Bodensee Fault Zone (FBBFZ). Both study areas were selected because recent “GeoBio-Interactions” findings showed, that red wood ants (RWA) are biological indicators of otherwise undetected degassing systems. A total of 817 soil gas samples was analyzed. Currently, Meinweg can be considered “no ants land” due to the very low background-level geogas concentrations. Thus, anomalies (Rn-CO₂) weakly trending in NE-SW extension direction emerged. This could probably indicate the onset of (re)activation of the NE-SW trending (Variscan) structures or the development of new fractures as an aftershock process of the 1992 Roermond earthquake that occurred about 15 km to the west. Results at Bodanrück (3 RWA clusters and two RWA-free corridors) revealed degassing patterns in NW-SE and NNE-SSW directions in the clusters corresponding to re-activated and recent strike-slip fault systems. No gas anomalies were found in RWA-free corridors. The RWA nest distribution was shown to be a valuable tool for identifying areas of even actively degassing spotty anomalies caused by macro- and microscale brittle deformation masked by sediment cover.

Various factors, such as uncertainty of component parameters and uncertainty of sensor meas-urement values, contribute to the difficulty of fault detection in the landing gear retrac-tion/extension hydraulic system. In this paper, we introduce linear fractional transformation technology and uncertainty analysis theory for the construction of the diagnostic bond graph of the landing gear retraction/extension hydraulic system. In this way, interval analytical redundancy relations and fault signature matrix can be derived. Using the fault signature matrix, existing faults of the system can be preliminarily detected and isolated. Additionally, interval analytical re-dundancy relations can be used to detect system faults in detail, and cases analysis can be carried out to determine if the actuator is externally or internally leaky, and if the landing gear selector valve is reversing stuck. Compared to the traditional analytical redundancy relations, this method takes into account the negative factors of uncertainty; and compared to the traditional absolute diagnostic threshold, the interval diagnostic threshold is more accurate and sensitive.

Grinding processes’ stochastic nature poses a challenge in predicting the quality of the resulting surfaces. Post-production measurements for form, surface roughness, and circumferential waviness are commonly performed due to infeasibility in measuring all quality parameters during the grinding operation. Therefore, it is challenging to diagnose the root cause of quality deviations in real-time resulting from variations in the machine’s operating condition. This paper introduces a novel approach to predicting the overall quality of the individual parts. The grinder is equipped with sensors to implement condition-based maintenance and is induced with five frequently occurring failure conditions for the experimental test runs. The crucial quality parameters are measured for the produced parts. Fuzzy c-means (FCM) and Hotelling’s T-squared (T2) have been evaluated to generate quality labels from the multi-variate quality data. Benchmarked random forest regression models are trained using fault diagnosis feature set and quality labels. Quality labels from the T2 statistic of quality parameters are preferred over FCM approach for their repeatability. The model, trained from T2 labels achieves more than 94% accuracy when compared to the measured ring disposition. The predicted overall quality using the sensors’ feature set is compared against the threshold to reach a trustworthy maintenance decision.

The Internet of Things (IoT) is experiencing widespread adoption across industry sectors ranging from supply chain management to smart cities, buildings, and health monitoring. However, most software architectures for IoT deployment rely on centralized cloud computing infrastructures to provide storage and computing power, as cloud providers have high economic incentives to organize their infrastructure into clusters. Despite these incentives, there has been a recent shift from centralized to decentralized architecture that harnesses the potential of edge devices, reduces network latency, and lowers infrastructure cost to support IoT applications. This shift has resulted in new edge computing architectures, but many still rely on centralized solutions for managing applications. A truly decentralized approach would offer interesting properties required for IoT use cases. To address these concerns, we introduce a decentralized architecture tailored for large scale deployments of peer-to-peer IoT sensor networks and capable of run-time application migration. The solution combines a blockchain consensus algorithm and verifiable random functions to ensure scalability, fault tolerance, transparency, and no single point of failure. We build on our previously presented theoretical simulations with many protocol improvements and an implementation tested in a use case related to monitoring a Slovenian cultural heritage building located in Bled, Slovenia.

A common requirement of embedded software in charge of safety tasks is to guarantee the identification of those Random Hardware Failures (RHFs) that can affect digital components. RHFs are unavoidable. For this reason, functional safety standards, like the ISO 26262 devoted to automotive applications, require embedded software designs able to detect and eventually mitigate them. For this purpose, various software-based error detection techniques have been proposed over the years, focusing mainly on detecting Control Flow Errors. Many Control Flow Checking (CFC) algorithms have been proposed to accomplish this task. However, applying these approaches can be difficult because their respective literature gives little guidance on the their practical implementation in high-level programming languages, and they have to be implemented in low-level code, e.g., assembly. Moreover, the current trend in the automotive industry is to adopt the so-called Model-Based Software Design approach, where an executable algorithm model is automatically translated into C or C++ source code. This paper presents two novelties: firstly, the compliance of the experimental data on the capabilities of Control Flow Checking (CFC) algorithms with the ISO 26262 automotive functional safety standard; Secondly, by the implementation of the CFC algorithm in the application behavioral model is automatically translated. There is no need to modify the code generator. The assessment was performed using a novel fault injection environment targeting a RISC-V (RV32I) microcontroller.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

The service conditions of underground coal mine equipment are poor, and it is difficult to accurately extract the fault characteristics of rolling bearings. In order to better improve the accuracy of fault identification of rolling bearings, a fault detection method based on multiscale permutation entropy and SOA-SVM is proposed. First, the whale optimization algorithm is used to select the modal analysis number K and the penalty factor α of the variational mode decomposition algorithm. Then, the vibration signal of rolling bearings is dissolved according to the optimized variational mode decomposition algorithm, and the multi-scale permutation entropy of the main intrinsic mode function is calculated. Finally, the feature values of the matrix are entered into the SVM algorithm optimized by the seagull optimization algorithm to obtain the classification result. The experimental results based on the published rolling bearing datasets of Western Reserve University show that the identification success rate of the proposed method can reach 98.75%. The fault detection of the rolling bearings can be completed accurately and efficiently.

In the next decade, further digitalisation of the entire wind energy project lifecycle is expected to be a major driver for reducing project costs and risks. In this paper, a literature review on the challenges related to implementation of digitalisation in the wind energy industry is first carried out, showing that there is a strong need for new solutions that enable co-innovation within and between organisations. Therefore, a new collaboration method called the WeDoWind Ecosystem is developed and demonstrated. The method is centred around specific "challenges", which are defined by "challenge providers" within a topical "space" and made available to participants via a digital platform. The data required in order to solve a particular "challenge" is provided by the "challenge providers" under the confidentiality conditions they specify. The method is demonstrated via a case study, the EDP Wind Turbine Fault Detection Challenge. Six submitted solutions using diverse approaches are evaluated. Two of the methods perform significantly better than EDP’s existing method in terms of Total Prediction Costs (saving up to €120,000). The WeDoWind Ecosystem is found to be a promising solution for enabling co-innovation in wind energy, providing a number of tangible benefits for both challenge and solution providers.

The health of the landing gear retraction and extension hydraulic system may be assessed using fuzzy comprehensive evaluation (FCE), however the traditional FCE method depends solely on human assessment by specialists, which is excessively subjective. To address the issue of excessive human subjective variables in the assessment, an improved FCE model based on enhanced risk coefficient is provided, which includes four consideration indexes: failure probability, failure severity, failure detection difficulty, and failure repair difficulty. To reduce subjective human judgment errors entirely due to expert experience, the improved FCE takes into account the likelihood of failure using a statistical method, the severity of failure using a fault simulation analysis based on the LMS Imagine.Lab AMESim simulation platform, and the difficulty of fault detection and repair using the aircraft manufacturer's professional maintenance information. As part of the evaluation model, the range of health assessment values and accompanying treatment methods are included, making it easier to implement on a daily basis in aircraft maintenance. As a final step, the simulation is evaluated and the simulated faults are calculated.

Large power transformers are generally associated with a maximum capacity rating of 100 MVA or higher. These large liquid dielectric power transformers are a custom-built piece of equipment, thus very expensive, and a backbone element of the power grid. In extreme cases as, for example, severe geomagnetic disturbances, permanently monitoring their condition will enhance their electrical reliability and resilience to guarantee efficient management of its life cycle. However, some traditional monitoring/diagnosis techniques have singular features when applied to large power transformers and their interlinked subsystems. In this context, and since that information is hardly put in evidence and compiled in the literature, this paper reviews the particularities of monitoring and diagnosing those assets.

Motivated for improving the efficiency and reliability of wind turbine energy conversion, this paper presents an advanced control design that enhances the power regulation efficiency and re-liability. The constrained behaviour of the wind turbine is taken into account, by using the barrier Lyapunov function in the analysis of the Lyapunov direct method. This, consequently, guarantees that the generated power remains within the desired bounds to satisfy the grid power demand. Moreover, a Nussbaum-type function is utilized in the control scheme, to cope with the unpre-dictable wind speed. This eliminates the need for accurate wind speed measurement or estimation. Furthermore, via properly designed adaptive laws, a robust actuator fault-tolerant capability is integrated into the scheme, handling the model uncertainty. Numerical simulations are performed on a high-fidelity wind turbine benchmark model, under different fault scenarios, to verify the effectiveness of the developed design. Also, a Monte-Carlo analysis is exploited for the evaluation of the reliability and robustness characteristics against the model-reality mismatch, measurement errors and disturbance effects.

A detection system, modeled in a graph, uses "detectors" on a subset of vertices to uniquely identify an "intruder" at any vertex. We consider two types of detection systems: open-locating-dominating (OLD) sets and identifying codes (ICs). An OLD set gives each vertex a unique, non-empty open neighborhood of detectors, while an IC provides a unique, non-empty closed neighborhood of detectors. We explore their fault-tolerant variants: redundant OLD (RED:OLD) sets and redundant ICs (RED:ICs), which ensure that removing/disabling at most one detector guarantees the properties of OLD sets and ICs, respectively. This paper focuses on constructing optimal RED:OLD sets and RED:ICs on the infinite king's grid, and presents the proof for the bounds on their minimum densities; [3/10, 1/3] for RED:OLD sets and [3/11, 1/3] for RED:ICs.

A new method for short circuit fault location is proposed based on instantaneous signal measurement and its derivatives, and is based on the retardation phenomena. The difference between the times in which a signal is registered in two detectors is used to locate the fault. Although a description of faults in terms of a lumped circuit is useful for elucidating the methods for detecting the fault. This description will not suffice to describe the fault signal propagation hence a distributed models is needed which is given in terms of the telegraph equations. Those equations are used to derive a transmission line transfer function, and an exact analytical description of the short circuit signal propagating in the transmission line is obtained. The analytical solution was verified both by numerical simulations and experimentally.

Desktop fused filament fabrication (FFF) 3D printers have been growing in popularity among hobbyist and professional users as a prototyping and low-volume manufacturing tool. One issue these printers face is the inability to determine when a defect has occurred rendering the print unusable. Several techniques have been proposed to detect such defects but many of these approaches are tailored to one specific fault (e.g., filament runout/jam), use expensive hardware such as laser distance sensors, and/or use machine vision algorithms which are sensitive to ambient conditions, and hence can be unreliable. This paper proposes a versatile, reliable, and low-cost system, named MTouch, to detect millimeter-scale defects that tend to make prints unusable. At the core of MTouch is an actuated contact probe designed using a low-power solenoid, magnet, and hall effect sensor. This sensor is used to check for the presence, or absence, of the printed object at specific locations. The MTouch probe demonstrated 100% reliability, which was significantly higher than the 74% reliability achieved using a commercially available contact probe (the BLTouch). Additionally, an algorithm was developed to automatically detect common print failures such as layer shifting, bed separation, and filament runout using the MTouch probe. The algorithm was implemented on a Raspberry Pi mini-computer via an Octoprint plug-in. In head-to-head testing against a commercially available print defect detection system (The Spaghetti Detective), the MTouch was able to detect faults 44% faster on average while only increasing the print time by 8.49%. In addition, MTouch was able to detect faults The Spaghetti Detective was unable to identify such as layer shifting and filament runout/jam.

Identifying and anticipating potential failures in the cloud is an effective method for increasing cloud reliability and proactive failure management. Many studies have been conducted to predict potential failure, but none have combined SMART (Self-Monitoring, Analysis, and Reporting Technology) hard drive metrics with other system metrics such as CPU utilisation. Therefore, we propose a combined metrics approach for failure prediction based on Artificial Intelligence to improve reliability. We tested over 100 cloud servers’ data and four AI algorithms: Random Forest, Gradient Boosting, Long-Short-Term Memory, and Gated Recurrent Unit. Our experimental result shows the benefits of combining metrics, outperforming state-of-the-art.

Having experienced large-scale disasters between 2004 and 2006, the fatalities due to large-scale disasters in 2018 were still high. In contrast, disaster risk management (DRM) and CDR in Japan have been continuously improved. Thus, there is a need to develop CDR for supporting DRM in Indonesia by learning from the Japanese experience, particularly in a disaster-prone area without large-scale disaster experience. This research was a pilot project on the development of CDR in Indonesia. The case study was a geological hazard-prone Lembang Fault area. People’s perception was collected using structured interviews, while demographic and local economic data was acquired from official statistical publications. Satellite imageries were utilized to acquire natural and built environment and land use/land cover and their changes between 2019 and 2021. Although the degrees of social capital, risk knowledge including indigenous knowledge and past disaster experience were high, government interventions on DRM and land administration are required to develop CDR in Lembang Fault area. Organized community development is expected rather than to solely involve NGOs. Moreover, strategies to develop economic resilience are needed to allow the community to bounce back from future disaster. Finally, a detail baseline data should be collected to develop DRM strategy and CDR.

Blockchain technology has been recognized as a promising solution to enhance the security and privacy of Internet of Things (IoT) and Edge Computing scenarios. Taking advantage of the Proof-of-Work (PoW) consensus protocol, which solves a computation intensive hashing puzzle, Blockchain assures the security of the system by establishing a digital ledger. However, the computation intensive PoW favors members possessing more computing power. In the IoT paradigm, fairness in the highly heterogeneous network edge environments must consider devices with various constraints on computation power. Inspired by the advanced features of Digital Twins (DT), an emerging concept that mirrors the lifespan and operational characteristics of physical objects, we propose a novel Miner-Twins (MinT) architecture to enable a fair PoW consensus mechanism for blockchains in IoT environments. MinT adopts an edge-fog-cloud hierarchy. All physical miners of the blockchain are deployed as microservices on distributed edge devices, while fog/cloud servers maintain digital twins that periodically update miners’ running status. By timely monitoring miner’s footage that is mirrored by twins, a lightweight Singular Spectrum Analysis (SSA) based detection achieves to identify individual misbehaved miners that violate fair mining. Moreover, we also design a novel Proof-of-Behavior (PoB) consensus algorithm to detect byzantine miners that collude to compromise a fair mining network. A preliminary study is conducted on a proof-of-concept prototype implementation, and experimental evaluation shows the feasibility and effectiveness of proposed MinT scheme under a distributed byzantine network environment.

This paper presents a robust and efficient fault detection and diagnosis framework for handling small faults and oscillations in synchronous generator (SG) systems. The proposed framework utilizes the Brunovsky form representation of nonlinear systems to mathematically formulate the fault detection problem. A differential-flatness model of SG systems is provided to meet the conditions of the Brunovsky form representation. A combination of high-gain observer and group method of data handling neural network is employed to estimate the trajectory of the system and to learn/ approximate the fault and uncertainties associated functions. The fault detection mechanism is developed based on output residual generation and monitoring so that any unfavourable oscillation and/or fault occurrence can be detected rapidly. Accordingly, an average L1-norm criterion is proposed for rapid decision making of faulty situations. The performance of the proposed framework is investigated for two benchmark scenarios which are actuation fault and fault impact on system dynamics. The simulation results demonstrate the capacity and effectiveness of the proposed solution for rapid fault detection and diagnosis in SG systems in practice, and thus enhancing service maintenance, protection, and life cycle of SGs.

Knowledge-based approaches are useful alternatives to predict the Failure Probability (FP) coping with the insufficient data, process integrity, and complexity issue in manufacturing systems. This study proposes a Fault Tree Analysis (FTA) approach as proactive knowledge-based technique to estimate the FP based maintenance planning with subjective information from domain experts. However, the classical-FTA still suffers from uncertainty and static structure limitations which poses a substantial dilemma in predicting FP. To deal with the uncertainty issues, a Fuzzy-FTA (FFTA) model was developed by statistical analysing the effective attributes such as experts' trait impacts, scales variation and, assorted membership and defuzzification functions. Besides, a Bayesian Network (BN) theory was conducted to overcome the static limitation of classical-FTA. The results of FFTA model revealed that the changes in decision attributes were not statistically significant on FP variation while BN model considering conditional rules to reflect the dynamic relationship between events had more impact on predicting FP. After all, the integrated FFTA-BN model was used in the optimization model to find the optimal maintenance intervals according to estimated FP and the total expected cost. As a practical example, the proposed model was implemented in a semi-automatic filling system in an automotive production line. The outcomes could be useful for upgrading the availability and safety of complex equipment in manufacturing systems.

In this paper, the problem of observer-based adaptive sliding mode control is discussed for nonlinear systems with sensor and actuator faults. The time-varying actuator degradation factor and external disturbance are considered in the system simultaneously. In this study, the original system is described as a new normal system by combining the state vector, sensor faults and external disturbance into a new state vector. For the augmented system, a new sliding mode observer is designed, where a discontinuous term is introduced such that the effects of sensor and actuator faults and external disturbance will be eliminated. In addition, based on a tricky design of the observer, the time-varying actuator degradation factor term is developed in the error system. On the basis of the state estimation, an integral-type adaptive fuzzy sliding mode controller is constructed to ensure the stability of the closed-loop system. Finally, the effectiveness of the proposed control methods can be illustrated with a numerical example.

Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Fault diagnosis of the gearbox is a decisive part of the modern industry to find the many gearbox defects like gear tooth crack, chipped or broken, etc. But sometimes, the nonstationary properties of vibration signal and low energy of minimal faults make this procedure very challenging. Previously, many types of techniques have been developed for gearbox condition monitoring. But most of the methods are dealing with conventional techniques of the gearbox condition monitoring, such as time-domain analysis or frequency domain analysis. Most of the conventional methods are not suitable for the nonstationary vibration signal. Thus, this paper presents a novel gearbox fault diagnosis technique using conditional temporal moments and an optimizable support vector machine (SVM). This work also presents an integrated features extraction technique based on the standard features, i.e., statistical and spectral features with the combinations of moment features. The impact of the four conditional temporal moments of each gearbox condition is also presented. This work shows that the proposed method successfully classifies and categorizes the gearbox faults at an early stage.

Our understanding of pull-apart basins and their fault systems has been enhanced by analog experiments and simulations. However, there has been no opportunity to compare the faults that constitute pull-apart basins with surface ruptures during earthquakes. In this study, we investigated the effects of a 2018 earthquake (Mw 7.5) on a pull-apart basin in the Palu-Koro fault system, Sulawesi Island, Indonesia, using geomorphic observations in digital elevation models, optical correlation with pre- and post-earthquake satellite images. A comparison of active fault traces determined by geomorphology with the locations of surface ruptures from the 2018 earthquake shows that some of the boundary faults of the basin are inactive and that active faulting has shifted to basin-shortcut faults and relay ramps. We also report evidence of lateral spreading, in which alluvial fan materials moved around the end of the alluvial fan. These phenomena may provide insights for anticipating the location of future surface ruptures in pull-apart basins.

A novel adaptive neural network-based fault-tolerant control scheme is proposed for six-degree freedom nonlinear helicopter dynamic. The proposed approach can detect and mitigate sensors' faults in real-time. An adaptive observer-based on neural network (NN) and extended Kalman filter (EKF) is designed, which incorporates the helicopter's dynamic model to detect faults in the navigation sensors. Based on the detected faults, an active fault-tolerant controller, including three loops of dynamic inversion, is designed to compensate for the occurred faults in real-time. The simulation results showed that the proposed approach is able to detect and mitigate different types of faults on the helicopter navigation sensors, and the helicopter tracks the desired trajectory without any interruption.

The fault diagnosis of safety critical systems such as wind turbine installations includes extremely challenging aspects that motivate the research issues considered in this paper. In fact, the prompt detection and the reliable diagnosis of faults in their earlier occurrence represent the key point especially for offshore installations. For these plants, operation and maintenance procedures in harsh environments would inevitably increase the cost of the energy production. Therefore, this work investigates fault diagnosis solutions that are considered in a viable way and used as advanced techniques for condition monitoring of dynamic processes. To this end, the work proposes the design of fault diagnosis strategies that exploit the estimation of the fault by means of data--driven approaches. This solution leads to the development of effective methods allowing the management of partially unknown information of the system dynamics, while coping with measurement errors, the model--reality mismatch and other disturbance effects. In mode detail, the proposed data--driven methodologies exploit fuzzy systems and neural networks in order to estimate the nonlinear dynamic relations between the input and output measurements of the considered process and the faults. To this end, the fuzzy and neural network structures are integrated with auto--regressive with exogenous input descriptions, thus making them able to approximate unknown nonlinear dynamic functions with arbitrary degree of accuracy. Once these models are estimated from the input and output data measurement acquired from the considered dynamic process, the capabilities of their fault diagnosis capabilities are validated by using a high--fidelity benchmark that simulates the healthy and the faulty behaviour of a wind turbine system. Moreover, at this stage the benchmark is also useful to analyse the robustness and the reliability characteristics of the developed tools in the presence of model--reality mismatch and modelling error effects featured by the wind turbine simulator. On the other hand, a hardware--in--the--loop tool is finally implemented for testing and comparing the performance of the developed fault diagnosis strategies in a more realistic environment and with respect to different fault diagnosis approaches.

The induced draft (ID) fan is important auxiliary equipment in the thermal power plant. It is of great significance to monitor the operation of the ID fan for safe and efficient production. In this paper, an adaptive warning model is proposed to detect early faults of ID fans. First, a non-parametric monitoring model is constructed to describe the normal operation states with the multivariate state estimation technique (MSET). Then, an early warning approach is presented to identify abnormal behaviors based on the results of the MSET model. As the performance of the MSET model is heavily influenced by the normal operation data in the historic memory matrix, an adaptive strategy is proposed by using the samples with a high data quality index (DQI) to manage the memory matrix and update the model. The proposed method is applied to a 300 MW coal-fired power plant for early fault detection, and it is compared with the model without an update. Results show that the proposed method can detect the fault earlier and more accurately.

Generalized stacking fault energies of palladium alloys were calculated using the density functional theory. The stacking fault energy of palladium alloys is correlated with the valence electron of the transition metal element. The twinning tendency is also modified by the presence of an alloying element in the plane of deformation. The obtained results suggest that Pd –transition metal alloys with elements such as Cr, Mo, W, Mn, Re are expected to exhibit high work hardening rate due to the tendency to emit of the partial dislocations and mechanical twins, which results in increased strength and ductility.

In this research work, an adaptive scheme for the coordinated protection of AC Microgrids using directional overcurrent (DOCR) relays is presented. Protection of AC MGs is a complex and challenging issue due to the dynamic nature of the network including, a) its capability to reconfigure the modes of operation ranging from grid-connected to the islanded mode, c) bidirectional-power flow capability, and c) integration of intermittent renewable energy resources with real-time variations in the resource availability. Consequently, the fault current contributions may largely vary depending upon the incident conditions on the network. Conventional protection schemes, generally designed for radial networks, and unidirectional power flow from the source end to the load may either mal-operate or exhibit very poor performance, if not adapted according to the dynamic conditions of the network. To address this issue, a communication-based adaptive protection scheme capable to adapt its settings according to the generation resource availability and network configuration is presented in this work. The proposed scheme consists of an intelligent central protection unit (ICPU) capable to update the settings and communicate it to the individual relays based on the pre-calculated offline settings. The directional overcurrent relays employed in the scheme use two-stage settings, i.e. definite time and inverse definite minimum time characteristics for the effective coordination among the downstream and upstream relays. An adaptive algorithm for ICPU operation is presented and a case study is implemented for a modified IEEE 9-bus system using DigSilent Power factory. The results for various scenarios including, a) grid-connected mode of operation, b) islanded mode of operation, and c) variable distributed generation mode are obtained and compared to the static scheme, which validates the effectiveness of the proposed scheme.

In this paper a novel and flexible solution for fault prediction based on data collected from Supervisory Control and Data Acquisition (SCADA) system is presented. Generic fault/status prediction is offered by means of a data driven approach based on a self-organizing map (SOM)and the definition of an original Key Performance Indicator (KPI). The model has been assessed on a park of three photovoltaic (PV) plants with installed capacity up to 10 MW, and on more than sixty inverter modules of three different technology brands. The results indicate that the proposed method is effective in predicting incipient generic faults in average up to 7 days in advance with true positives rate up to 95%. The model is easily deployable for on-line monitoring of anomalies on new PV plants and technologies, requiring only the availability of historical SCADA data, fault taxonomy and inverter electrical datasheet.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

Reliability assessment is an important component and tool used for process plants since the facility consists of many loops and instruments attached and operates based on each other availability, thus it requires a statistical method to visualize the reliability. The paper focuses on reliability assessment and prediction based on available statistical models such as normal, log-normal, exponential, and Weibull distribution. This paper also visualizes, which model fits best for assessment and prediction and also considers failure modes caused during a simulation mode process control operation. A simulation model is designed in this paper to observe the failure of the control valve causing stiction to visualize the failure modes and predict the best-fit model for reliability assessment.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.

In this work, a hybrid component Fault Detection and Diagnosis (FDD) approach for industrial sensor systems is established and analyzed, to provide a hybrid schema that combines the advantages and eliminates the drawbacks of both model-based and data-driven methods of diagnosis. Moreover, it shines the light on a new utilization of Random Forest (RF) together with model-based diagnosis, beyond its ordinary data-driven application. RF is trained and hyperparameter tuned using three-fold cross validation over a random grid of parameters using random search, to finally generate diagnostic graphs as the dynamic, data-driven part of this system. This is followed by translating those graphs into model-based rules in the form of if-else statements, SQL queries or semantic queries such as SPARQL, in order to feed the dynamic rules into a structured model essential for further diagnosis. The RF hyperparameters are consistently updated online using the newly generated sensor data to maintain the dynamicity and accuracy of the generated graphs and rules thereafter. The architecture of the proposed method is demonstrated in a comprehensive manner, and the dynamic rules extraction phase is applied using a case study on condition monitoring of a hydraulic test rig using time-series multivariate sensor readings.

We identify the source of the Mw = 5.6 earthquake that hit west-central Epirus on March 21, 2020 00:49:52 UTC. We use synthetic aperture radar interferograms tied to one permanent Global Navigation Satellite System (GNSS) station (GARD). We model the source by inverting the INSAR displacement data. The inversion model suggests a shallow source on a low-angle fault (39°) dipping towards east with a centroid depth of 8.5 km. The seismic moment deduced from our model agrees with those of the published seismic moment tensors. This geometry is compatible with the Margariti thrust fault within the collision zone between Apulia and Eurasia. We also processed new GNSS data and estimate a total convergence rate between Apulia and Eurasia of 8.9 mm yr-1 , of which shortening of the crust between the Epirus coastal GNSS stations and station PAXO in the Ionian Sea is equivalent to ~ 50% of it or 4.6 mm yr−1. A 60-km wide deformation zone takes up nearly most of the convergence between Apulia-Eurasia, trending N318°E. Its central axis runs along the southwest coast of Corfu, along the northeast coast of Paxos, heading toward the northern extremity of the Lefkada island.

Feature selection is a crucial step to overcome the curse of dimensionality problem in data mining. This work proposes Recursive k-means Silhouette Elimination (RkSE) as a new unsupervised feature selection algorithm to reduce dimensionality in univariate and multivariate time-series datasets. Where k-means clustering is applied recursively to select the cluster representative features, following a unique application of silhouette measure for each cluster and a user-defined threshold as the feature selection or elimination criteria. The proposed method is evaluated on a hydraulic test rig, multi sensor readings in two different fashions: (1) Reduce the dimensionality in a multivariate classification problem using various classifiers of different functionalities. (2) Classification of univariate data in a sliding window scenario, where RkSE is used as a window compression method, to reduce the window dimensionality by selecting the best time points in a sliding window. Moreover, the results are validated using 10-fold cross validation technique. As well as, compared to the results when the classification is pulled directly with no feature selection applied. Additionally, a new taxonomy for k-means based feature selection methods is proposed. The experimental results and observations in the two comprehensive experiments demonstrated in this work reveal the capabilities and accuracy of the proposed method.

An attractive option for realizing applications in radiation environments is to employ All-Programmable System-on-Chips (APSoCs) thanks to their high-performance computing and power efficiency merits. Despite APSoC's advantages, like any other electronic device, they are prone to radiation effects. Processors found in APSoCs must, therefore, be adequately hardened against ionizing-radiation to become a viable alternative for harsh environments. This paper proposes a novel triple-core lockstep (TCLS) approach to secure the Xilinx Zynq-7000 APSoC dual-core ARM Cortex-A9 processor against radiation-induced soft errors by coupling it with a MicroBlaze TMR subsystem in Zynq's programmable logic (PL) layer. The proposed strategy uses software-level checkpointing principles along with roll-back and roll-forward mechanisms (i.e. software redundancy), and hardware-level processor replication as well as checker circuits (i.e. hardware redundancy). Results of fault injection experiments show that the proposed solution achieved high soft error security by mitigating about 99% of bit-flips injected into both ARM cores' register data.

In recent years, intelligent fault diagnosis algorithms using deep learning method have achieved much success. However, the signals collected by sensors contain a lot of noise, which will have a great impact on the accuracy of the diagnostic model. To address this problem, we propose a one-dimensional convolutional neural network with multi-scale kernels (MSK-1DCNN) and apply this method to bearing fault diagnosis. We use a multi-scale convolution structure to extract different fault features in the original signal, and use the ELU activation function instead of the ReLU function in the multi-scale convolution structure to improve the anti-noise ability of MSK-1DCNN; then we use the training set with pepper noise to train the network to suppress overfitting. We use the Western Reserve University bearing data to verify the effectiveness of the algorithm and compare it with other fault diagnosis algorithms. Experimental results show that the improvements we proposed have effectively improved the diagnosis performers of MSK-1DCNN under strong noise and the diagnosis accuracy is higher than other comparison algorithms.