Fogo volcano erupted in 2014-15 producing an extensive lava flow field in the summit caldera that destroyed two villages, Portela and Bangaeira. The eruption started with powerful explosive activity, lava fountains, and a substantial ash column accompanying the opening of an eruptive fissure. Lava flows spreading from the base of the eruptive fissure produced three arterial lava flows. By a week after the start of the eruption, a master lava tube had already developed within the eruptive fissure and along the arterial flow. In this paper, we analyze the emplacement processes on the basis of observations carried out directly on the lava flow field, remote sensing measurements carried out with a thermal camera, SO₂ fluxes, and satellite images, in order to unravel the key factors leading to the development of lava tubes. These were responsible for the rapid expansion of lava for the ~7.9 km length of the flow field, as well as the destruction of the Portela and Bangaeira villages. The key factors leading to the development of tubes were the low topography and the steady magma supply rate along the arterial lava flow. Comparing time-averaged effusion rates (TADR) obtained from satellite and Supply Rate (SR) derived from SO₂ flux data, we estimate the amount and timing of the lava flow field endogenous growth, with the aim of developing a tool that could be used for hazard assessment and risk mitigation at this and other volcanoes.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T₁ = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T₂ = 50 kg N ha^-1, T₃ = 100 kg N ha^-1 and T₄ = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T₅: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T₆: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T₇: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO₂ concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T₆ = Split N₁₀₀) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

In this contribution, different lane-keeping control strategies for Autonomous Ground Vehicles (AGV) have been analyzed and compared. The AGV must be oriented and kept within a given reference path using the front wheel steering angle as the control action for a specific longitudinal velocity. While non-linear models can describe the lateral dynamics of the vehicle in an accurate manner, they might lead to difficulties when computing some real-time control laws such as Model Predictive Control (MPC). Linear Parameter Varying (LPV) models can provide a trade-off between computational complexity and model accuracy. Another way to reduce computational complexity is to explore other control strategies, for example, the one based on the Inverse Kinematic Bicycle model (IKIBI). Additionally, AGV sensors typically work at different measurement acquisition frequencies so that Kalman Filters (KF) are usually needed for sensor fusion. If these frequencies are slower than the actuation rate, a multi-rate KF may be needed. The two control strategies (MPC using a LPV model and IKIBI) have been compared in simulations over a circuit path in the presence of process and measurement Gaussian noise. The MPC controller has shown to provide a more accurate lane-keeping behavior than an IKIBI control strategy. Finally, it has been seen that Dual-Rate Extended Kalman Filters (DREKF) constitute an essential tool when only slow and noisy sensor feedback is available in an AGV lane-keeping application.

In this study, we surveyed over 600 participants to determine: a) major causes to mental stress during the pandemic and its future impacts, and b) diversity in public perception and acceptance (specifically for children) of Covid-19 vaccination. Statistical results and intelligent clustering outcomes indicate significant relationships between sociodemographic diversity, mental stress causes, vaccination perception, and Covid-19 infections. For instance, statistical results indicate significant dependence between mental stress due to Covid-19 and gender (p = 1.7e-05). Over 25% of males indicated work related stress comparing 35% in females however, females indicated more stressed (17%) due to relationships comparing to males (12%). Around 30% of Asian/Arabic participants don’t feel vaccination being safe as compared to 8% of white-British and 22% of white-European indicating significant dependence (p = 1.8e-08) with ethnicity. More specifically, vaccination acceptance for children is significantly dependent to ethnicity (p = 3.7e-05) where only 47% participants show willingness towards children’s vaccination. Primary dataset in this study along with experimental outcomes identifying sociodemographic information diversity with respect to public perception and acceptance of vaccination to children and potential stress factors might be useful for public and policy makers to be better prepared for future epidemics as well as working globally to combat mental health issues and running more effective vaccination campaigns.

The fetal heart rate (FHR) is a screening signal for preventing fetal hypoxia during labor. When experts analyze this signal, they have to position a baseline and then identify decelerations and accelerations. These steps can potentially be automated and made more objective by signal processing analysis. Various methods have been described in the literature but there are no open-source programs for performing these steps. The MATLAB toolbox presented here comprises a standard signal pre-processing function, 11 re-coded literature methods for fetal heart rate analysis, a signal viewer (enabling annotation by an expert) and an evaluation procedure with various criteria measuring intrarater agreement.

Dental implants provide a predictable treatment option for partial and complete edentulism via the placement of fixed permanent artificial root to support prosthetic dental crowns. Despite the high survival rates, long-term implant failures are still reported leading to implant removal and additional financial and health burdens. While extrinsic factors that improve survival rate of implants have been well explored, the impact of genetic factors on this matter is poorly understood. A systematic review and meta-analysis study was conducted to determine whether genetic factors contribute to increase the risk of dental implant failure. A comprehensive search for peer-reviewed articles on dental implants and genetics was performed using various literature database libraries. The study design was conducted according to PRISMA guidelines, and the obtained records were registered in PROSPERO database. According to the exclusion/inclusion criteria, 11 studies were eligible for this study out of 808 articles. The meta-analysis of the combined association studies of DNA variations and dental implants did not indicate an increase risk for implant failure due to DNA variations in IL-1B, IL-10 and TNF-α. This study emphasizes the need for larger randomized controlled clinical trails to inform clinicians and patients about the role of genetic factors on dental implant survival and success rate in healthy and compromised patients.

The In this paper, a universal method has been developed, which is a combination of an optimization method and a method for assessing the marginal utility. At present, the problem of optimal load distribution in the power system between a hydropower plant (HPP) and thermal power plants (TPP) is solved using the equality of the differential incremental rate characteristics of fuel consumption at TPP and water consumption at HPP by the Lagrangian multiplier method. In this case, the number of iterations can be five or more. The proposed approach is based, first of all, on the correct representation of the differential characteristics and calculation of a hydro resource price for the operational control of the HPP. Based on the comparison of water volume at a HPP and fuel amount at combined heat and power plants (CHPP) used for generation of 1 kW power, it is possible to determine a water price for a HPP. As a result of implementing the developed method for the HPP, a price of sold electricity in the flexible energy market will be comparable with the price for sold electricity produced at CHPPs, being equal to approximately 120 rubles/MW∙h.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

Tuning nonlinearity of the laser is the main source which will deteriorate the spatial resolution in optical frequency domain reflectometry system. We develop methods for tuning nonlinearity correction in the OFDR system from the aspects of data acquisition and also the posting-processing. A zero-crossing detection scheme is researched and implemented by a customized circuit. Equal-spacing frequency sampling is therefore achieved in real-time. The maximum sensing distance can reach to the same length of the auxiliary interferometer. The zero-crossing detection for the beating frequency of 20MHz is achieved. Then, a nonlinearity correction method based on the self-reference method is proposed. The auxiliary interferometer is no longer necessary in this scheme. The tuning information of the laser is extracted by a strong reflectivity point at the end of the sensing arm in the main interferometer. The tuning information can then be used to resample the raw signal and the nonlinearity correction can be achieved. The spatial resolution test and the distributed sensing experiments are both performed based on this nonlinearity correction method. The results validated the feasibility of the proposed method. The method reduces the hardware and data burden for the system and has a potential value on the system integration and miniaturization.

Physics theory has yet to settle on specific descriptions for new elementary particles, for dark matter, and for dark energy forces. Our work extrapolates from the known elementary particles. The work suggests well-specified candidate descriptions for new elementary particles, dark matter, and dark energy forces. This part of the work does not depend on theories of motion. This work embraces symmetries that correlate with motion-centric conservation laws. The candidate descriptions seem to explain data that prior physics theory seems not to explain. Some of that data pertains to elementary particles. Our theory suggests relationships between masses of elementary particles. Our theory suggests a relationship between the strengths of electromagnetism and gravity. Some of that data pertains to astrophysics. Our theory seems to explain ratios of dark matter effects to ordinary matter effects. Our theory seems to explain aspects of galaxy formation. Some of that data pertains to cosmology. Our theory suggests bases for inflation and for changes in the rate of expansion of the universe. Generally, our work proposes extensions to theory in three fields. The fields are elementary particles, astrophysics, and cosmology. Our work suggests new elementary particles and seems to explain otherwise unexplained data.

Although floods, as well as other natural disasters, can be considered relevant causes of intra-generational inequalities, the frequent catastrophes and the resulting damages to territory reflect the generalized indifference about inter-generational justice. Societal concerns, such as land protection, typically involve the administrative system performing proactive policies in the perspective of inter-generational solidarity, but subsidiarity has made more and more independent the local communities. As a consequence, the attention toward the long run effects – typically concerning the territorial system, as a whole, at the geographical scale – has been dispersed, and the proactive policies coming from the central government has became more ineffective. Regarding the case of the flood happened in 2009 in the Fiumedinisi-Capo Peloro hydraulic basin, in the northeastern part of Sicily, Italy, we propose an economic valuation – carried out by performing the method of the imputed preferences – in order to compare the expenses incurred by the public authorities responsible for protecting the territory to the costs of the rehabilitation of the damaged areas. Some considerations about the economic significance of the proactive policies for the arrangement of territory are addressed according to the role played by the social discount rate in the inter-temporal economic calculation.

Staphylococcus aureus is a high-priority pathogen causing severe infections with high morbidity and mortality worldwide. Many S. aureus strains are methicillin-resistant (MRSA) or even multi-drug resistant. It is one of the most successful and prominent modern pathogens. An effective fight against S. aureus infections requires novel targets for antimicrobial and antistaphylococcal therapies. Recent advances in whole-genome sequencing and high-throughput techniques facilitate the generation of genome-scale metabolic models (GEMs). Among the multiple applications of GEMs is drug-targeting in pathogens. Hence, comprehensive and predictive metabolic reconstructions of S. aureus could facilitate the identification of novel targets for antimicrobial therapies. This review aims at giving an overview of all available GEMs of multiple S. aureus strains. We downloaded all 114 available GEMs of S. aureus for further analysis. The scope of each model was evaluated, including the number of reactions, metabolites, and genes.Furthermore, all models were quality-controlled using Mᴇᴍᴏᴛᴇ, an open-source application with standardized metabolic tests. Growth capabilities and model similarities were examined. This review should lead as a guide for choosing the appropriate GEM for a given research question. With the information about the availability, the format, and the strengths and potentials of each model, one can either choose an existing model or combine several models to create models with even higher predictive values. This facilitates model-driven discoveries of novel antimicrobial targets to fight multi-drug resistant S. aureus strains.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

The effect of reprocessing on the quasi-static uniaxial tensile behavior of two commercial polypropylene (PP) based composites is experimentally investigated and modeled. In particular, the studied materials consist of an unfilled high-impact PP and a talc-filled high-impact PP. These PP composites are subjected to repeated processing cycles including a grinding step and an extrusion step to simulate recycling at the laboratory level, the selected reprocessing numbers for this study being 0, 3, 6, 9 and 12. Because the repeated reprocessing leads to thermo-mechanical degradation by chain scission mechanisms, the tensile behavior of the two materials exhibits a continuous decrease of elastic modulus and failure strain with increasing number of reprocessing. A physically consistent three-dimensional constitutive model is used to predict the tensile response of non-recycled materials with strain rate dependence. For the recycled materials, the reprocessing effect is accounted by incorporating the reprocessing sensitive coefficient into the constitutive model for Young’s modulus, failure strain, softening and hardening equations. Our predictions of true stress - true strain curves for non-recycled and recycled 108MF97 and 7510 are in a good agreement with experimental data.

The purpose of this study is to examine the connection between economic growth and unemployment in Liberia between 2001 and 2019. The unit root test and the Augmented Dickey-Fuller (ADF) Co-integration test were used to examine the relationship between unemployment and GDP. The Auto Regressive Distribution Lag (ARDL) bounds test is used to determine if the variables are linked in the long run. According to the results of the ARDL model, there is no long-run relationship between unemployment and economic growth. This study' results have particularly important policy implications for Liberian economic authorities. In both the long and medium term, the observational results showed no meaningful relationship between unemployment and economic growth. The Liberian government should direct its spending toward activities that directly and indirectly promote the creation of employment and decent jobs, a conducive environment and flexible labor market policies or legislation that are not impediments to job creation, and finally, the government should prioritize labor intensive industries.

This research article examines the state-wise literacy rates in India, with a focus on male and female literacy, as well as the disparities between them. The data was sourced from a survey conducted by the National Statistical Office (NSO), with a special emphasis on Union Territories and Northeastern states based on the 2011 Census. Kerala boasts the highest literacy rate at 96.2%, while Andhra Pradesh reports the lowest at 66.4%. Notably, the national male-female literacy gap stands at 12.9%. Kerala also demonstrates the smallest gender gap at 2.2%, while Rajasthan exhibits the highest at 23.3%. Through descriptive and explorative analysis, this article provides a comprehensive overview of literacy rates across various Indian states and Union Territories, highlighting the significant disparities that exist.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

Athletes are exposed to high-intensity loads to promote athletic performance, however without appropriate evaluation for its effects. This study investigates the effects of four types of exhaustion exercises on Heart Rate Variability (HRV) and Poincaré features as markers of central fatigue; Creatine Kinase (CK) and blood lactate concentrations ([LA-]b) as biomarkers of peripheral fatigue. To achieve this purpose, ten healthy volunteers were exposed to exhaustive exercise using isotonic-, isometric-, aerobic-, and anaerobic-fatigue protocols. HRV Poincaré features, standard deviation of instantaneous beat-to-beat R-R interval variability (SD1) and standard deviation of continuous long-term R-R interval variability (SD2) variables were collected. Central fatigue was tested through the sympathetic stress index (SS) and the sympathetic and parasympathetic index (SS/SD1). Blood samples were collected at the beginning and at the end of the exercises to determine CK and [LA-]b. The SD1 decreased in each exercise protocol, while the SS and SS/SD1 increased. [LA-]b and CK increased at the end of each protocol and correlated with SD1 and SS/SD1. HRV, CK, and [LA^-]_b are acute markers to detect, both central and peripheral fatigue; sensitive to the type, duration, and intensity of exercise, being HRV a novel noninvasive marker, simple and useful for sports coaches and athletes.

In this study, regression analyses were used to find a relationship between the rain gauge rainfall rate R and radar reflectivity Z for the urban catchment of the Służewiecki Stream in Warsaw, Poland. Rainfall totals for 18 events which were measured at two rainfall stations were used for these analyses. Various methods for determining calculational values of radar reflectivity in reference to specific rainfall cells with 1-km resolution within an event duration were applied. The influence of each of these methods on the Z-R relationship was analyzed. The correction coefficient for data from the SRI (Surface Rainfall Intensity) product was established, in which the values of rainfall rate are calculated based on parameters a and b determined by Marshall and Palmer. Relatively good agreement between measured and estimated rainfall totals for the analyzed events was obtained using the Z-R relationships as well as the correction coefficient determined in this study. Rainfall depths estimated from radar data for two selected events were used to simulate flow hydrographs in the catchment using the SWMM (Storm Water Management Model) hydrodynamic model. Different scenarios were applied to investigate the stream response to changes in rainfall depths, in which the data both for 2 existing as well as 64 virtual rain gauges assigned to appropriate rainfall cells in the catchment were included.

The present paper proposes a fractal analysis of the Covid-19 dynamics in 45 European countries. We introduce a new idea of using the box-counting dimension of the epidemiologic curves as a means of classifying the Covid-19 pandemic in the countries taken into consideration. The classification can be a useful tool in deciding upon the quality and accuracy of the data available. We also investigated the reproduction rate, which proves to have significant fractal features, thus enabling another perspective on this epidemic characteristic. Moreover, we studied the correlation between two meteorological parameters: global radiation and daily mean temperature and two Covid-19 indicators: daily new cases and reproduction rate. The fractal dimension differences between the analysed time series graphs could represent a preliminary analysis criterion, increasing research efficiency. Daily global radiation was found to be stronger linked with Covid-19 new cases than air temperature (with a greater correlation coefficient -0.386, as compared with -0.318), and consequently it is recommended as the first-choice meteorological variable for prediction models.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

We describe the effect of the expansion of space on the wavelength of the light beam in a Fabry-Pérot interferometer. For an instrument such as the Laser Interferometer Gravitational-Wave Observatory (LIGO), which has high sensitivity and a long period of light storage, the wavelength ${\lambda }_L$ of laser photons are redshifted due to the expansion of space in each cavity by an amount $\delta \lambda$ given by $\delta \lambda /{\lambda }_L=H_0{\tau }_s\approx 8.8\times {10}^{-21}$ , where $H_0\approx 2.2\times {10}^{-18}{\mathrm{s}}^{-1}$ is the Hubble constant and ${\tau }_s\approx 4\mathrm{ms}$ is the light storage time for the cavity. Since ${\tau }_s$ is based on the cavity finesse $\mathcal{F}$ which depends on the laser beam full width at half maximum (FWHM) $\delta \omega$ of each cavity, we show that a difference in finesses between the LIGO arm cavities produces a signal $h_H\left(t\right)$ at the anti-symmetric output port given by $h_H\left(t\right)=2a_1{H}_0\left(\frac{1}{\delta {\omega }_X\left(t\right)}-\frac{1}{\delta {\omega }_Y\left(t\right)}\right),$ where $\delta {\omega }_X\left(t\right)$ and $\delta {\omega }_Y\left(t\right)$ are the beam FWHM at time t, respectively, for the X and Y arm cavities and $a_1$ is a beam proportionality constant to be determined expermentally. Assuming $a_1\approx 1$ , then for cavity beams FWHM of $\delta \omega \left(t\right)\approx (523.2\pm 31)\mathrm{rad}.{\mathrm{s}}^{-1}$ the output signal has the range $\mid h_H\left(t\right)\mid \le 1\times {10}^{-21}$ , which is detectable by advanced LIGO.

Due to the increase in the emission of greenhouse gases, the hydrologic cycle is being altered on the daily basis. This has affected the variations in relations of intensity, duration, and frequency of rainfall events. Intensity Duration Frequency (IDF) curves describe the relationship between rainfall intensity, rainfall duration and return period. IDF curves are one of the most often applied implements in water resource engineering, in areas such as for operating, planning and designing of water resource projects, or for numerous engineering projects aimed at controlling floods. In particular, IDF curves for precipitation answer problems of improper drainage systems or conditions and extreme characters of precipitation which are the main cause of floods in Nyabugogo catchment. This study aims to establish Rainfall IDF empirical equations, curves and hydrological discharge (predicted peak rate of runoff (Qlogy)) equations for eight Districts that will be used for designing an appropriate and sustainable hydraulic structures for controlling flood to reduce potential loss of human and aquatic life, degradation of water, air and soil quality and property damage and economic lessen caused by flood in Nyabugogo catchment. However Goodness of Fit tests revealed that Gumbel’s Extreme-Value Distribution method appears to have the most appropriate fit compared with Pearson type III distribution for validating the Intensity-Duration-Frequency curves and equations through the use of daily annual for each meteorological station. The findings of the study show that the intensity of rainfall increases with a decrease in rainfall duration. Additionally, a rainfall of every known duration will have a higher intensity if its return period is high, while the predicted peak rate of runoff (Qlogy) increases also with an increase in the intensity of rainfall.

To analyze the predictive ability and incremental value of left ventricular longitudinal axis strain (LAS) and late gadolinium enhancement (LGE) using standard cardiovascular magnetic resonance (CMR) imaging for the diagnosis and prognosis of severe aortic stenosis (AS) in patients with an indication for aortic valve replacement. We conducted a prospective study on 128 patients with severe AS and 52 volunteers. The evaluation protocol included standard biochemistry tests, novel biomarkers of myocardial fibrosis, 12-lead electrocardiograms and 24-hour Holter, the 6-minute walk test and extensive echocardiographic and CMR imaging studies. Outcomes were defined as the composite of major cardiovascular events (MACEs). Among AS patients, most (n = 17, 77.2%) of those who exhibited LGE at CMR imaging had MACEs during follow-up. Kaplan-Meier curves for event-free survival showed a significantly higher rate of MACEs in patients with LGE (p < 0.01) and decreased LAS (p < 0.001). In Cox regression analysis, only reduced LAS [hazard ratio 1.33, 95%CI (1.01 to 1.74), p < 0.01] and the presence of LGE [hazard ratio 11.3, 95%CI (1.82 to 70.0), p < 0.01] were independent predictors for MACEs. The predictive value increased if both LGE and reduced LAS were added to LVEF. None of the biomarkers of increased collagen turnover exhibited any predictive value for MACEs. LAS by CMR is an independent predictor of outcomes in patients with AS and provides incremental value beyond the assessment of LVEF and the presence of LGE.

This paper considers a hybrid relay network consisting of the source, the amplify-and-forward (AF) relay, the decode-and-forward (DF) relay, and the destination. We propose the optimal power allocation schemes between two different relays which maximize the achievable rate under a sum relay power constraint for given channel gains and transmit power from source. By solving the optimization problem to maximize the achievable rate for each relay network, the transmit power values in closed-form are derived. When the channel gains are the same, the optimal power allocation scheme for AF-DF relay network proves that a more power should be allocated at the first relay to maximize the achievable rate. In case of the DF-AF relay network, we derive the optimal power allocation scheme for the possible four cases. Under the same SNR condition at the first hop, we show that the achievable rate of AF-DF relay network is greater than that of DF-AF relay network when the channel gain between two relays is higher than that between the second relay and destination. Simulation results show that the proposed power allocation schemes provide a higher achievable rate than the equal power allocation schemes.

Tomato leaf curl disease (TLCD) is the most common viral disease in the tomato plant. It is caused by begomoviruses, which are viruses that cause plant development to be slowed. Many of the traditional disease management methods are still in use. They are, however, ineffective and out of date. Modern biotechnology is being used to detect illness in tomato plants as early as possible, thus reducing damage to the plants. Through genetic engineering, the spread of viruses may be controlled or prevented entirely. Here reviewed many methods for decreasing or eliminating the viral influence on crop growth through biotechnology and genomics. We also investigated the possibility of genetic engineering to reduce or remove the virus TLCD impact on tomato crop development.

The initial outbreak of COVID-19 was first reported in Wuhan (China) during the latter part of December 2019. Indonesia has the fourth-largest population globally and reported the country’s first case of the virus on 2nd March 2020. The World Health Organisation (WHO) in addition to several neighbouring provinces and educational institutions within the region began questioning the Indonesian government upon the initial case reported. The objective of this study was to describe the epidemiological characteristics of the COVID-19 outbreak in Indonesia during March 2020. The data were collected from Indonesian government databases and non-government organisations (NGOs). The data were analysed using Microsoft Office 2019 (Excel) and Adobe Illustrator 2017 software, was used in drawing the map depicting the distribution of COVID-19 in Indonesia. As at 31st March 2020, a total of 1,528 people in Indonesia have been infected by COVID-19, in addition to 136 mortalities (CFR of 8.9%). Jakarta, as the principal capital of Indonesia, quickly has become the epicentre of the virus since this period. Most patient cases were attributed to those aged between 31 and 70 years (72.64%), with male patients (64.93%) representing the highest incidence of cases compared to female patients (35.07%). The number of ventilating machines was 3,326, with hospital numbers at 859. The distribution of cases depicting COVID-19 was mainly seen in urban areas compared to rural areas. Males compared to females, are at a higher risk of contracting COVID-19, including those aged below 30, between 30 and 60 or above. Indonesia also has the highest case fatality rate (CFR) with respect to mortalities in Southeast Asia and has the second-highest CFR globally. Similarly, while the number of ventilator machines as at 31st March 2020 were sufficient in meeting the growing number of COVID-19 cases in the country, it is possible that the government may need to increase the number of ventilators if the cases continue to escalate.

Two peat cores from two bogs were used to reconstruct high–resolution changes in atmospheric Pb accumulation rate (Pb AR) in Belgium during the Roman period. The two records were compared to assess the reliability of peat cores as archives of atmospheric Pb deposition and to established histories of atmospheric emissions from anthropogenic sources. To address these issues we analyze Pb concentration and isotopes, using ICP-MS, LA-ICP-MS and MC-ICP-MS in two peat sections, spanning 1000 yr each. Lead concentrations in the two cores range from 0.1 to 60 μg g⁻¹, with the maxima between 15 and 60 μg g⁻¹. The average natural background of Pb AR was 0.005± 0.002 mg m^-2 yr^-1 and the maximum ranges from 0.7 to 1.2 mg m^-2 yr^-1 between 50 BC and AD 215. The highest Pb AR exceed the pre-Roman period values by a factor of 25-30. Pb isotopic composition indicates that mining and metallurgical activities were the predominant sources of pollution during the Roman period. The Pb AR and chronologies in the Belgian peat cores are consistent with those reported for other continental archives as lake sediments, peat and ice cores.

The main objective was to determine the effect of mobile phone radiation on general health and electrolytes among students who use mobile phones. A questionnaire was designed and applied to 103 healthy and 36 deaf female students to select cases that meeting the inclusion criteria. For assessment of salivary parameters, the participants were classified into three groups. Group I was the control group, which included 17 deaf students. Group II was healthy students who have mobile phone for less than 5 years. Group III was healthy students who have mobile phone for 5 years or more. The results showed that the participants who use mobile phone had several problems in their health including dry mouth, bad odor from mouth, drooling of saliva, as well as ear and eye pain. The participants who use mobile phone complained of headache, anxiety and forgetfulness as compared to deaf participants. The study showed that there was no significant difference between pH and flow rate of saliva in all tested groups. This study has also shown that salivary level of Na+ and K+ were significantly lower in mobile phone users when compared to non users of mobile phone.

Mixtures of methacrylic polymers are the most common materials for making composites to be used as resins for dental and cosmetic applications. Some of these mixtures are composed by poly (ethyl methacrylate) (PEMA) and poly (methyl methacrylate) (PMMA), which constitute a solid component to be mixed with a liquid component made out of methacrylate monomers. The reaction between the thermal initiator benzoyl peroxyde (BPO) present in the solid component and the activator of the polymerization process, N,N-dimethyl-p-toluidine (DMT) present in the liquid component, gives rise to thermoset materials. In the present study, different liquid formulations composed by a mixture of two methacrylic monomers, ethyl methacrylate (EMA) and triethylene glycol dimethacrylate (TEGDMA) for cosmetic applications, were prepared and characterized, using a commercial powder (POW) composed by PEMA and PMMA. With the aim of improving workability during final application of the material, it was necessary to slow down the polymerization rate of liquid formulations. Their thermal behaviour was investigated by DSC in order to check the polymerization rate. Thermal stability of final materials was determined by TGA. DMTA, microindentation hardness and impact tests were performed on final materials, to assess their performance with respect to standard formulation. The combination of thermal and mechanical properties allows choosing which formulations could be suitable for use in cosmetics.

Background and objectives: Smoking leads to autonomic dysfunction. However, the clinical methods for diagnosing this dysfunction are not sufficient. Since exogenous hypoxia leads to changes in the autonomic cardiac control, the aim of our study was to compare the activity of the autonomic nervous system via heart rate variability (HRV) in young “healthy” smokers and non-smokers before, during and after a short-term exogenous hypoxic exposure. Methods: Twenty-one healthy non-smoking males aged 28.0±7.4 (mean±SD) and fourteen healthy smoking males aged 28.1±4.3 with 9.2±5.6 pack-years were subjected to one-hour hypoxic exposure (FiО2=12.3±1.5%) via hypoxicator (AltiPro 8850 Summit+, Altitude Tech, Canada) with simultaneous recording of electrocardiography and pulse oximetry. HRV data was derived via specific software (Kubios HRV, Finland) by analyzing the pre-hypoxic, hypoxic and post-hypoxic periods. Results: Standard deviation of the intervals between normal beats (SDNN) was higher in non-smokers in the pre-hypoxic period (62.0±32.1 vs 40.3±16.2, p=0.013) but not in hypoxia (75.7±34.8 vs 57.9±18.3, p=0.167). When comparing intragroup HRV changes of shifting from hypoxic to post-hypoxic (normoxic) conditions we found that there is a significant increase in the root mean square of successive RR interval differences (RMSSD) (65.9±40.2 vs 75.1±45.9, p=0.011) and in the high frequency (lnHF) (6.8±1.4 vs 7.2±1.3, p=0.014) and a decrease in LF/HF (3.0±2.3 vs 1.9±1.5, p<0.001), but these changes were observed only in the group of non-smokers. Conclusions: Smoking likely impairs autonomic regulation in young healthy males and may lead to a decreased HRV even before subjective clinical signs and symptoms. Hypoxic exposure test could be applied in clinical practice for early detection of autonomic dysfunction in smokers, because their parasympathetic reactivation is blunted when shifting from hypoxic to normoxic ambient conditions measured by HRV.

Studies showed that introversion is the strongest personality trait related to perceived social isolation (loneliness), which can predict various complications beyond objective isolation such as living alone. Lonely individuals are more likely resort to social media for instantaneous comfort, but it is not a perpetual solution. Largely negative implications including poorer interpersonal relationship and depression were reported due to excessive social media usage. Conversational task is an established intervention to improve verbal communication, cognitive and behavioral adaptation among lonely individuals. Despite that behavioral benefits have been reported, it is unclear if they are accompanied by objective benefits underlying physiological changes. Here, we investigate the physiological signals from 28 healthy individuals during a conversational task. Participants were ranked by trait extraversion, where greater introversion is associated with increased susceptibility to perceived social isolation as compared to participants with greater extraversion as controls. We found that introverts had a greater tendency to be neurotic, and these participants also exhibited significant differences in task-related electrodermal activity (EDA), heart rate (HR) and HR variability (HRV) as compared to controls. Notably, resting state HRV among individuals susceptible to perceived loneliness was below the healthy thresholds established in literature. Conversational task with a stranger significantly increased HRV among individuals susceptible to isolation up to levels as seen in controls. Since HRV is also elevated by physical exercise and administration of oxytocin hormone (one form of therapy for behavioral isolation), conversational therapy among introverts could potentially confer physiological benefits to ameliorate social isolation and loneliness. Our findings also suggest that although the recent pandemic have changed how people are interacting typically, we should maintain a healthy dose of social interaction innovatively.

The aim of the work was to update the distribution range of Aedes (Stegomyia) albopictus Skuse in the Americas, review the blood-feeding patterns and compare the minimum infection rate (MIR) of the dengue virus (DENV) between studies of vertical and horizontal transmission. The current dis-tribution of Ae. albopictus encompasses 21 countries in the Americas. Extensive review has been conducted for the blood-feeding patterns of Ae. albopictus. The results suggest that the mosquito is capable of feeding on 16 species of mammals and five species of avian. Humans, dogs, and rats are the most common host. Eight arboviruses with the potential to infect humans and animals have been isolated in Ae. albopictus. In the United States of America (USA), Eastern equine encephalitis virus, Keystone virus, La Crosse Virus, West Nile virus, and Cache Valley virus were isolated in the Asian mosquito. In Brazil, Mexico, Colombia, and Costa Rica, DENV (all serotypes) has been frequently identified in field-caught Ae. albopictus. Overall, the estimated MIR in Ae. albopictus infected with DENV is similar between horizontal (10.95) and vertical transmission (8.28). However, in vertical transmission, there is a difference in the MIR values if the DENV is identified from larvae or adults (males and females emerged from a collection of eggs or larvae). MIR es-timated from larvae is 14.04 and in adults is 4.04. In conclusion, it has to be highlighted that Ae. albopictus is an invasive mosquito with wide phenotypic plasticity to adapt to broad and new areas, it is highly efficient to transmit the DENV horizontally and vertically, it can participate in the inter-endemic transmission of the dengue disease, and it can spread zoonotic arboviruses across forest and urban settings.

Excessive vibration of temporary grandstand owing to crowd has lateral rhythmic motions can cause human in panic, which attracted increasing attention in recent years. This paper focuses on experiments that a temporary grandstand occupied 20 participants is oscillated by a shaking table with a series of random waves and induced by crowd with rhythmic swaying motions at lateral direction, respectively. And then a series of vibration perception questionnaires about crowd reaction are obtained. Evaluation of annoying level derives in concept of degree of membership and annoying rate method is proposed, then the human health risk of vibration serviceability of temporary grandstand is assessed with acceleration vibration dose value(VDV). From these results it is clear that standing crowd is more tolerant to vibration than seated crowd. The measured vibrations generated by crowd activities on temporary grandstand can cause panic in crowd. New relationship between the annoyance rate and structural acceleration VDV at logarithmic coordinate is proposed. The findings of this study can be utilized to manage the vibration of temporary grandstand and assess the human health risk.

The aim of this study is to empirically examine the link between foreign direct investment (FDI) and domestic investment (DI) in South Africa over the period of 41 years (1975-2016). Accurately, it attempts to determine whether FDI crowds in or crowds out DI in South Africa. DI is sub-divided into private domestic investment (credit to domestic private sector) and public corporation investment (state owned enterprises). We used the Autoregressive Distributed Lag-Error Correction Model (ARDL-ECM) technique to ascertain long run and short run effects concurrently after establishing that the variables were stationary (using the PP test). The results of the unit root test shows that all variables are integrated of order zero I(0) or integrated of order one I(1), indicating that the series of variables are stationary in the level or first difference form. The findings revealed that variables are cointegrated in the long run. The ARDL model found a negative link between FDI and domestic investment. The result implies that FDI crowds out domestic investment. Moreover, the long run estimate revealed that domestic investment is crowded in by government investment expenditure (GINV). Other findings uncovered that, GDP crowds out private domestic investment while crowding in public corporation investment. Moreover, the long run estimate revealed that domestic investment is crowded in by gross domestic savings (SAV). On the other hand, the real exchange rate (EXCR) crowds out private domestic investment while crowding in public corporation investment. Trade openness (TRA) crowds out domestic investment. Additionally, the short run estimate uncovered that private domestic investment is crowded out by FDI, EXCR, and TRA whereas GINV, GDP and SAV is crowding in private domestic investment. Other findings discovered that, in the short run, public corporation investment is crowded out by FDI, GDP, EXCR and TRA, while GINV and SAV crowd in public corporation investment. The CUSUM confirms that the models are structurally firmness.

Decision tree algorithms have been among the most popular algorithms for interpretable (transparent) machine learning since the early 1980s. On the other hand, deep learning methods have boosted the capacity of machine learning algorithms and are now being used for non-trivial applications in various applied domains. But training a fully-connected deep feed-forward network by gradient-descent backpropagation is slow and requires arbitrary choices regarding the number of hidden units and layers. In this paper, we propose near-optimal neural regression trees, intending to make it much faster than deep feed-forward networks and for which it is not essential to specify the number of hidden units in the hidden layers of the neural network in advance. The key idea is to construct a decision tree and then simulate the decision tree with a neural network. This work aims to build a mathematical formulation of neural trees and gain the complementary benefits of both sparse optimal decision trees and neural trees. We propose near-optimal sparse neural trees (NSNT) that is shown to be asymptotically consistent and robust in nature. Additionally, the proposed NSNT model obtain a fast rate of convergence which is near-optimal up to some logarithmic factor. We comprehensively benchmark the proposed method on a sample of 80 datasets (40 classification datasets and 40 regression datasets) from the UCI machine learning repository. We establish that the proposed method is likely to outperform the current state-of-the-art methods (random forest, XGBoost, optimal classification tree, and near-optimal nonlinear trees) for the majority of the datasets.

Plants produce above- and below-ground biomass. However, our understanding of both production and decomposition of below-ground biomass is poor, largely because of the difficulties of accessing study materials. Below-ground organic matter decomposition studies are scanty and especially rare in the tropics. Here, we used a litter bag experiment to quantify the mass loss and nutrients dynamics of decomposing twigs and fine roots from an arbuscular mycorrhizal fungal associated tree, Parashorea chinensis, in a tropical rain forest in Southwest China. Overall, twig litter decomposed 1.9 times faster than fine roots (decay rate (k) twig=0.255, root=0.134). The difference in decomposition rates can be explained by a difference in phosphorus (P) concentration, availability and use by decomposers or C quality. Both materials showed an increase in N concentration, with final measurements still higher than initial levels. This suggests N may not be available due to microbial immobilization. Both carbon and nitrogen dynamics were significantly predicted by mass loss and showed a negative and positive relationship, respectively. Our study results imply that fine roots carbon and nitrogen contribute more to soils organic matter and enlarge the resident time. Therefore, better understanding of carbon cycle requires better understanding of mechanisms governing below ground biomass decomposition.

Previous studies investigated the effects of seed rates and seed recycling practices on the yield and yield related variables. However, higher yield does not always guarantee cost-efficiency. This study aimed at investigating the yield effects of plot-level seed rate along with the cost-benefit analysis of seed recycling practices. This study has introduced the dose-response model to the existing analytical methods used in analyzing the effect of different agrochemicals on crop yield. A multi-stage stratified sampling technique was used to select a total of 450 sample respondents. Data was gathered using a mix of data collection tools. Descriptive statistics along with the dose-response model have been applied for data analysis. Farmers of the study were found to be dissimilar in terms of their seed rate application. The dose-response analysis indicated that the highest average wheat yield has been associated with a seed rate of 50 kg ha-1 above what is recommended. The yield effect of seed recycling has also been assessed and a one-time seed recycling has caused a yield decline of 665 kg ha-1 as compared to the non-recycled seeds. The cost reduced by using recycled seed is by far lower than the economic gains associated with using unrecycled and fresh seeds. The cost-benefit analysis made clear that farmers can reduce their seed costs through seed recycling but their yields and net income can be best improved by using unrecycled CBWS. Thus, farmers must be encouraged to make use of unrecycled seed by establishing agricultural credit schemes geared towards seed procurement and seed price subsidy as key strategies to reduce economically wasteful seed recycling practices.

The paper investigates the possible use of a low strength domestic sand (D) (up to today useless – not considered as proppant source) of small particle sizes, instead to that of high strength imported commercial sand (C), as a prospective micro-proppant for low permeability reservoirs in Poland. There is need to develop national unconventional gas resources like tight gas, shale gas and coalbed methane. An important energy source of value and readily available in Poland is coal. The basins of this resource are large and bears low permeability coalbed methane reservoirs which needs to be developed to contribute to the energy security, economy and environmental needs of the country. These reservoirs need technological assistance such as hydraulic fracturing which makes use of proppants for development. Most of the commonly used proppants over the years for fracturing have been large grain size commercial proppants of high strength material content bought abroad. Investigated finer proppants are known to have the ability to penetrate narrow fracture networks to ensure effective high reservoir volume and conductivity for production. Results from presented laboratory research shows the D - proppant, which is cheaper and readily available, has the 3K class with low settling rates as a potential micro-proppant for effective transportation, enhancement of conductivity and production rate in the narrow fractures of low permeability reservoirs. Future using of domestic proppant will decrease stimulation cost and will have positive impact on the environment due to omitting long distance transportation from abroad.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

Drought decreases grain yield of sorghum [Sorghum bicolor (L.) Moench], and understanding the mechanism(s) related to drought tolerance is critical for sustaining sorghum production. Variation in root and shoot traits associated with drought tolerance were analyzed to provide an integrated view of factors that underlie the drought tolerance of sorghum. The plants were grown in the root column up to the five-leaf stage, then exposed to either 0.9 fraction of transpirable soil water (FTSW) or 0.4 FTSW for five days. In another experiment, at the five-leaf stage, stress was imposed for 14 days. Various root and shoot traits associated with drought tolerance were recorded. The seminal root angle of IS13540 was lower (24.4) than IS23143 (42.6). Drought stress increased the maximum root length (40%) and total root length (58%) of IS13540 than its irrigated control. In contrast, the maximum root length and total root length were decreased in IS23143. Similarly, across the lines, drought stress decreased stomatal conductance (37%), transpiration rate (42%), photosynthetic rate (40%), photosystem II quantum yield (20%), photochemical quenching (44%), and total dry matter production (34%) than irrigated control. An increased transpiration rate was observed in IS23143 than IS13540 under irrigated and drought stress. In IS23143, the reduction in photosynthetic rate under drought may be a combination of stomatal and non-stomatal factors. However, in IS13540, the reduction is especially by the stomatal factors. It is evident that IS13540 is a drought-tolerant line, and tolerance is related to a deep prolific root system and reduced tran-spiration rate.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

The present study documented the presence of seagrass Halodule uninervis for the first time along with previously documented Halophila ovalis at Haripur creek. The population structure of both these seagrass species is assessed. The physico-chemical parameters were similar for both seagrass species except for the sediment grain size fractions. The sand content of H. ovalis patches was 1.2-fold higher than H. uninervis beds, whereas the silt content of H. uninervis beds was 2-fold higher than H. ovalis patches. The pH levels were lower than the standard oceanic pH of 8.2. Macroalgae like Ceramium sp. and Gracilaria verrucosa were growing on the leaves of H. uninervis due to high nitrate and phosphate levels of the creek waters. Leaf reddening was only observed in the leaves of H. ovalis. Under similar environmental conditions, H. ovalis (5004 ± 114.51 ind. m-²) had a 2-fold lower shoot density than that of the H. uninervis (11598 ± 187.52 ind. m-²). Both above- and below-ground biomass of H. ovalis (96.34 ± 10.18 and 197.5 ± 18.30 g DW m^-2) was 2-fold lower than that of H. uninervis (198 ±7.45 and 456 ± 9.59 g DW m^-2). H. uninervis leaves were 9-fold longer than that of H. ovalis, whereas H. ovalis leaves were 5-fold wider than H. uninervis. The leaf plastochrone interval is 2.3 days for H. ovalis and 9.6 days for H. uninervis. Consequently, the leaf growth rate of H. ovalis is 2-fold lower than that of H. uninervis. H. ovalis had 2.6-fold longer internodes than H. uninervis. The root length of H. uninervis was longer than H. ovalis. Consequently, the shorter root length of H. ovalis led to higher branching frequency than H. uninervis. The total C and N content were higher in the leaves of H. ovalis than H. uninervis.

La minería es una industria intensiva en energía que requiere una fuente estable de electricidad. Con el aumento de la demanda de minerales y la disminución de las leyes, se espera que la demanda de energía aumente en un 36% para el 2035. Este aumento de la demanda depende del uso de combustibles fósiles ya que la electricidad producida y comprada en las empresas mineras se basan principalmente en el caso de los combustibles fósiles, los costos de los sistemas de almacenamiento de energía solar y eólica han caído a una escala sin precedentes, lo que alienta a las empresas mineras a probar estas tecnologías.Entre los factores que influyen en el uso de energía renovable, se encuentra el beneficio a la comunidad en la etapa de operación y cierre o post-cierre de un proyecto minero, el siguiente factor es el perfil de consumo eléctrico o demanda es importante para el cálculo de su almacenamiento o no, de las energías renovables a utilizar. Como tercer factor está el cálculo del consumo en los procesos. Los rangos de penetración determinarán si es posible su almacenamiento de energía, y si es posible utilizar control híbrido (solar - eólico), para ello es importante el uso de herramientas digitales como el programa Holmer, es una herramienta importante que técnica y económica.El gobierno debe tener una perspectiva que ayude en los temas regulatorios necesarios para impulsar proyectos de energía renovable con diferentes incentivos e intereses según el contexto minero.

Outer particles collision with certain dynamic object is not a pure impact wear behavior; it is typically accompanied by sliding wear phenomena. This study aimed investigating the impact-sliding wear performance of three different TC17 titanium alloys. One was untreated, and the other two were subjected to laser shock peening (LSP) by 5 and 7 J pulse energy, respectively. Wear test was performed on a novel impact-sliding wear testing rig, which can realize multiple impact-sliding motions by changing motion parameters in x and z directions. Present results showed that wear resistance of both treated samples improved compared with the untreated alloy. Given the increase in wear cycles, increment in wear rate of the untreated sample was constantly higher than those of treated samples. All results can be attributed to the increase in surface hardness of the material and residual compressive stress, which was also introduced after LSP.

This study aligns with the 2030 United Nations Sustainable Development Goals- 3 which aim to “ensure healthy lives and promote well-being for all at all ages”. It contributes to the nascent literature stream on energy-health dynamics by introducing a holistic theoretical model to empirically examine the mediation effect of carbon emissions on the relationship between nonrenewable energy and infant mortality rates. Using an unbalanced panel data on 42 Asia and the Pacific countries from 2005 to 2015 and deploying the structural equation modeling approach, the empirical results are surmised as follows: (i) in regard to the full sample of countries, nonrenewable energy indirectly increases infant mortality rates through increasing carbon emissions. In other words, carbon emissions play a partial mediation role between nonrenewable energy and infant mortality rates; and (ii) for the different income groups, carbon emissions show varying mediation effects. For example, the mediation effects of carbon emissions in lower-middle and upper-middle income countries are found to be similar to those of the full sample of countries. Therefore, based on these findings, we conclude that nonrenewable energy is an essential determinant of infant mortality rates. Policy recommendations are put forward.

Body acceleration due the heartbeat-induced reaction forces can be measured as smartphone accelerometer (m-ACC) signals. Our aim was to test the feasibility of using m-ACC to detect changes induced by stress by ultra-short heart rate variability (USV) indices (SDNN and RMSSD). Sixteen healthy volunteers were recruited; m-ACC was recorded while in supine position, during spontaneous breathing (REST) and during one minute of mental stress (MS) induced by arithmetic serial subtraction task, simultaneous with conventional ECG. Beat occurrences were extracted from both ECG and m-ACC and used to compute USV indices using 60, 30 and 10s durations, both for REST and MS. A feasibility of 93.8% in the beat-to-beat m-ACC heart rate series extraction was reached. In both ECG and m-ACC series, compared to REST, in MS the mean beat duration was reduced by 15% and RMSSD decreased by 38%. These results show that short term recordings (up to 10 sec) of cardiac activity using smartphone’s accelerometers are able to capture the decrease in parasympathetic tone, in agreement with the induced stimulus.

In 2019, the Global Burden of Disease (GBD) estimated that prostate cancer (PC) was the 16th cause of death globally in males. In Mexico, PC epidemiology has been reported for a selected number of metrics and years, although without including the most up-to-date estimates. Herein, we describe and compare the burden and trends of PC in Mexico and its 32 states from 2000 to 2019. For this, we extracted online available data from the GBD 2019 to estimate the crude and age-standardized rate (ASR per 100,000 people) of incidence, mortality, and disability-adjusted life years (DALYs). In Mexico, PC caused 27.1 thousand (95% uncertainty intervals, 20.6-36.0 thousand) incident cases, 9.2 thousand (7.7-12.7 thousand) deaths, and 161.5 thousand (122.7-219.5 thousand) DALYs in males of all ages in 2019. Among states, Sinaloa had the greatest ASR of incidence and Guerrero the highest values of deaths and DALYs. The burden of PC showed an increasing trend, although the magnitude of change differed between metrics and locations. We found both an increasing national trend and subnational variation in the burden of PC. Our results confirm the need for updated and timely estimates to design effective diagnostic and treatment campaigns in locations where the burden of PC is the highest.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T1 = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T2 = 50 kg N ha^-1, T3 = 100 kg N ha^-1 and T4 = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T5: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T6: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T7: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO2 concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T6 = Split N100) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

This paper examines the asymmetrical relationship between exchange rate and consumer prices in 40 Sub-Saharan African (SSA) countries from 1990q1 to 2017q4. The exchange rate pass-through (ERPT) to consumer prices is estimated for each country by using the nonlinear autoregressive distributed lags (NARDL) framework and dynamic panel estimators robust to cross-sectionally correlated errors. Firstly, our findings suggest an asymmetrical ERPT in the SSA region during the short-term, whereas there are mixed results across sub-regions in the long-term. Next, we find incomplete and significant ERPT to consumer prices in the entire SSA region which is higher during the depreciation of the local currency than after appreciations. Third, we find nonlinear ERPT with respect to the size of the exchange rate. The pass-through is higher during large exchange rate changes than after small changes. Finally, we find that the pass-through is greater in the countries with fixed exchange rate regime (CFA franc zone) having low inflationary environment than in the other SSA countries with flexible exchange rate regime and high inflation levels. As a result, policymakers should take into account these asymmetries and non-linearities to improve the credibility of monetary policy, strengthen trade liberalization and establish competitive market structures in the Sub-Saharan region.

The gastrointestinal (GI) tract is a continuous channel through the body that consists of the esophagus, the stomach, the small intestine, the large intestine, and the rectum. Its primary functions are to move the intake of food for digestion before storing and ultimately expulsion of feces from the rectum through the anal sphincter. The mechanical behavior of GI tissues thus plays a crucial role for GI function in health and disease. The mechanical properties are typically characterized by a constitutive biomechanical model, which is a mathematical representation of the relation between load and deformation in a tissue. Hence, validated biomechanical constitutive models are essential to characterize and simulate the mechanical behavior of the GI tract under physiological and pathological conditions. Numerous constitutive models have consequently been proposed over the past three decades, mainly inspired by work done in cardiovascular tissues. Here, a comprehensive review of these constitutive models is provided. This review is limited to studies where a model of the strain energy function is proposed to characterize the stress-strain relation of a GI tissue. Several needs are identified for more advanced modeling of GI biomechanics including: 1) Microstructural models that provide actual structure-function relations; 2) Validation of coupled electro-mechanical models accounting for active muscle contractions; 3) Human data under physiological and pathological conditions to develop and validate models. The findings from this review provide guidelines for using existing constitutive models as well as perspective and directions for future studies aimed at establishing new constitutive models for GI tissues.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

The Finite size Lyapunov exponent (FSLE) has been used extensively since the late 1990’s to diagnose turbulent regimes from Lagrangian experiments and to detect Lagrangian coherent structures in geophysical flows and two-dimensional turbulence. Historically, the FSLE was defined in terms of its computational method rather than via a mathematical formulation, and the behavior of the FSLE in the turbulent inertial ranges is based primarily on scaling arguments. Here we propose an exact definition of the FSLE based on conditional averaging of the finite amplitude growth rate (FAGR) of the particle pair separation. With this new definition, we show that the FSLE is a close proxy for the inverse structural time, a concept introduced a decade before the FSLE. The (in)dependence of the FSLE on initial conditions is also discussed, as well as the links between the FAGR and other relevant Lagrangian metrics, such as the finite time Lyapunov exponent and the second order velocity structure function.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

Direct yaw moment control (DYC) is an effective way to alter the behaviour of electric cars with independent drives. Controlling the torque applied to each wheel can improve the handling performance of a vehicle making it safer andfaster on a race track. The state-of-the-art literature covers the comparison of various controllers (PID, LPV, LQR, SMC, etc.) using ISO manoeuvres. However, more advanced comparison on important characteristics of the controllers performance is missed, such as the robustness of the controllers under changes in the vehicle model, steering behaviour, use of the friction circle and, ultimately, lap time on a track. In this study, we have compared the controllers according to some of the aforementioned parameters on a modelled race car. Interestingly, best lap times are not provided by perfect neutral or close-to-neutral behaviour of the vehicle, but rather by allowing certain deviations from the target yaw rate. In addition, a modified PID controller showed that its performance is comparable to other more complex control techniques such as MPC.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

This study aims to determine how the effect of interest rates and changes in the dollar exchange rate (USD) on the stock price. The type of research carried out in this research is quantitative research with the object of research, namely Bank Central Asia (BCA). The data used in this study comes from secondary data, namely from books, the internet, documents, and banking sites. This study indicates that the independent variable, namely the interest rate, has a significant negative effect on the joint-stock price index and the other independent variable, namely the dollar exchange rate (USD), has a significant positive effect on the joint-stock price index. The coefficient test results show that interest rates and exchange rates (USD) simultaneously affect stock prices, namely 67.2% while the remaining 32.8% is influenced by other factors.

Two sets of initial conditions are used in the investigation of capital return rate and carbon storage in boreal forests. Firstly, a growth model is applied in young stands as early as the inventory-based model is applicable. Secondly, the growth model is applied to observed wooded stands. Four sets of thinning schedules are investigated in either case. First, the capital return rate is aspired without any restriction. Second, the number of thinnings is restricted to at most one. Third, thinnings are restricted to the removal of only trees thicker than 237 mm. Fourth, commercial thinnings are omitted. The two sets of initial conditions yield similar results. The capital return rate is a weak function of rotation age, which results in variability in the optimal number of thinnings. Reducing the number of thinnings to one increases timber stock but induces a capital return rate deficiency. The deficiency per excess volume unit is smaller if the severity of any thinning is restricted by the removal of large trees only. Omission of thinnings best applies to spruce-dominated stands with stem count less than 2000/ha. Restricted thinning intensity applies to deciduous stands and dense pine stands. The albedo effect increases the benefits of restricted thinnings and increased clearcuttings instead of contradicting the carbon storage.

The changing dynamics in climate is the primary and important determinant of agriculture productivity. The effects of this changing climate on overall productivity in agriculture can be understood when we study the effects of individual components contributing to the changing climate on plants and crops. Elevated CO₂ (eCO₂) and drought due to high variability in rainfall is one of the important manifestations of the changing climate. There is a considerable amount of literature that addresses climate effects on plant systems from molecules to ecosystems. Of particular interest is the effect of increased CO₂ on plants in relation to drought and water stress. As it is known that one of the consistent effects of increased CO₂ in the atmosphere is increased photosynthesis, especially in C₃ plants, it will be interesting to know the effect of drought in relation to elevated CO₂. The potential of elevated CO₂ ameliorating the effects of water deficit stress is evident from literature suggesting that these two are agents are brothers in arms protecting the plant from stress rather than partnering in crime, specifically water deficit when in isolation. The possible mechanisms by which this occurs will be discussed in this minireview. Interpreting the effects of short-term and long-term exposure of plants to elevated CO₂ in the context of ameliorating the negative impacts of drought will show us the possible ways by which there can be effective adaption to crops in the changing climate scenario.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

Photoplethysmography (PPG) is a simple-to-perform vascular optics measurement technique that can detect changes in blood volume in the microvascular tissue bed. Beat-to-beat analysis of the PPG waveform enables the study of the variability of pulse features such as amplitude and pulse arrival time (PAT), and when quantified in the time and frequency domains, has considerable potential to shed light on perfusion changes associated with peripheral arterial disease (PAD). In this pilot study innovative multi-site bilateral finger and toe PPG recordings from 43 healthy control subjects and 31 PAD subjects were compared (recordings each at least 5 minutes, collected in a warm temperature-controlled room). Beat-to-beat normalized amplitude and PAT variability was then quantified in the time-domain using SD and IQR measures and in the frequency-domain bilaterally using Magnitude Squared Coherence (MSC). Significantly reduced normalized amplitude variability (healthy control 0.0384 (IQR 0.0217-0.0744) vs PAD 0.0160 (0.0080-0.0338) (p<0.001) and significantly increased PAT variability (healthy control 0.0063 (0.0052-0.0086) vs PAD 0.0093 (0.0078-0.0144) (p<0.001) was demonstrated in PAD using the time-domain analysis. Frequency-domain analysis demonstrated significantly lower MSC values across a range of frequency bands for PAD patients. These changes suggest a loss of right-to-left body side coherence and cardiovascular control in PAD. This study has also demonstrated the feasibility of using these measurement and analysis methods in studies investigating multi-site PPG variability for a wide range of cardiac and vascular patient groups.

The production of instant green tea requires hot-water extraction, which is time consuming and contributes to losses in aromatic compounds. In this study, an ultrasonic-assisted technology was used to improve the extraction efficiency of green tea, thereby shortening extraction time from 45 to 15 min. In pure water, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 0.23 mg/mL and total tea polyphenol dissolution decreased by 3.2 mg/mL. In 76.2% ethanol, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 1.57mg/mL and total tea polyphenol dissolution decreased by 1.5 mg/mL. Additionally, we used microwave-assisted technology to further improve the extraction efficiency of green tea, which shortened the extraction time to 2 min. However, the extraction rate remained unchanged. In pure water, the dissolution of caffeine and theanine did not change significantly, but the dissolution of total catechins increased by 0.41 mg/mL and the dissolution of tea polyphenols decreased by 2.9 mg/mL. Ultrasonic treatment increased the proportion of 3-hydroxybutan-2-one, (5S)-5-(hydroxymethyl)oxolan-2-one and 2-phenylethanol, which were the main aroma compounds in tea. Microwave treatment changed the aroma compounds in tea, causing losses in aroma compounds with low boiling point and maintaining (5S)-5-(hydroxymethyl)oxolan-2-one. The taste and aroma of instant green tea improved based on sensory evaluation results.

Natural products have long played a major role in medicine and science. The garden snail Cornu aspersa is a rich source of biologically active natural substances which might be an important source for new drugs to treat human disease. Based on our previous studies seven fractions containing compounds with Mw &lt;3 kDa, &lt;10 kDa, &lt;20 kDa, &gt;20 kDa, and between 3-5 kDa, 5-10 kDa, and 10-30 kDa were purified from the mucus of C. aspersa and analyzed by tandem mass spectrometry (MALDI-TOF/TOF). Seventeen novel peptides with potential antibacterial activity have been identified by de novo MS/MS sequencing using tandem mass spectrometry. The different fractions were tested for antibacterial activity against Gram─ (Pseudomonas aureofaciens and Escherichia coli) and Gram+ (Brevibacillus laterosporus) bacterial strains as well anaerobic bacterium Clostridium perfringens. These results revealed that the peptide fractions exhibit a predominant antibacterial activity against B. laterosporus, the fraction with Mw 10 – 30 kDa against E. coli, another peptide fraction &lt;20 kDa against P. aureofaciens, and the protein fraction &gt;20 kDa against the bacterial strain C. perfringens. The discovery of new antimicrobial peptides (AMPs) from natural sources is of great importance for public health due to their effective antimicrobial activities and low resistance rates.

Accurate and stable cost forecasting of substation projects is of great significance to ensure the economic construction and sustainable operation of power engineering projects. In this paper, a forecasting model based on the improved least squares support vector machine (ILSSVM) optimized by wolf pack algorithm(WPA) is proposed to improve the accuracy and stability of the cost forecasting of substation projects. Firstly, the optimal features are selected through the data inconsistency rate (DIR), which helps reduce redundant input vectors. Secondly, the wolf pack algorithm is used to optimize the parameters of the improved least square support vector machine. Lastly, the cost forecasting method of WPA-DIR-ILSSVM is established. In this paper, 88 substation projects in different regions from 2015 to 2017 are chosen to conduct the training tests to verify the validity of the model. The results indicate that the new hybrid WPA-DIR-ILSSVM model presents better accuracy, robustness and generality in cost forecasting of substation projects.

Resveratrol, because of its low solubility in water and its high membrane permeability, is collocated in the second class of the biopharmaceutical classification system, with limited bioavailability due to its dissolution rate. Solid dispersion of resveratrol supported on magnesium dihydroxide (RESV@MDH) was evaluated to improve solubility and increase bioavailability of resveratrol. Fluorimetric microscopy and granulometric analysis display three types of microparticles with similar size: type 1 that emitted preferably fluorescence at 463 nm (λ_ecc 358 nm), type 2 that emitted preferably fluorescence at 605 nm (λ_ecc 550 nm) andtype 3 that are non-fluorescent. Micronized pure resveratrol display only microparticles type 1 whereas type 3 are associated to pure magnesium dihydroxide. Dissolution test in simulated gastric environment resveratrol derived from RESV@MDH in comparison to resveratrol alone displayed better solubility. According to the biopharmaceutical classification, an increase of 3 fold of resveratrol bioavailabilitywas observed after oral administration of 50 mg/Kg of resveratrol of RESV@MDH in rabbits. We hypothesize that type 2 microparticles represent magnesium dihydroxide microparticles with a resveratrol shell and that they are responsible for the improved resveratrol solubility and bioavailability of RESV@MDH.

During the COVID-19 lockdown in Wuhan, transportation, industrial production and other human activities declined significantly, as did the NO2 concentration. In order to assess the relative contributions of different factors to reductions of air pollutants, sensitivity experiments were implemented by random forest (RF) model, with the comparison of contributions of meteorology, road traffic, and emission sources between different periods. Besides, an emulator was operated to suggest an appropriate limit for control of transportation. The RF models showed different mechanisms for air pollutants. Within-city Migration index (WMI) was more important in the normal, pre-lockdown and post-pandemic model while Out-Migration Index (OMI) was emphasized in the lockdown model. In the COVID-19 lockdown period, 73.3% of the reduction can be attributed to the decreased road traffic, showing massive impact of road traffic on the air quality. In the post-pandemic period, meteorology controlled about 42.2% of the decrease and emissions from industry and household controlled 40.0% while road traffic only contributed to 17.8%. It was suggested that priority of restriction should be given to road traffic within the city. A limit of less than 40% on the control of the road traffic can get a better effect, especially for cities with severe traffic pollution.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

In this report the positive cases of Covid19 in India with effect from 7th September ,2020 to 25th October ,2020 are analysed for statistical relevance . The scattered data are used to find out a model equation correlating two variables number of recovered Covid –patient with an interval of regular seven days . The best fit regression analysis shows a significant correlation of Pearson coefficient (r) with standard error ( s ) with a probable lower mortality rate . Finally the limitations of this analysis is discussed herewith .

Polychlorinated phenoxathiins (PCPTs), polychlorinated dibenzothiophenes (PCDTs), and polychlorinated thianthrenes (PCTAs) are sulfur analogues of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/DFs). Chlorothiophenols(CTPs) and chlorophenols (CPs) are key precursors to form PCTA/PT/DTs, which can form chloro(thio)phenoxy radical, sulfydryl/hydryl-substituted phenyl radical and (thio)phenoxyl diradicals. The available radical/radical PCTA/DT formation mechanism failed to explain the higher concentration of PCDTs than that of PCTAs under the pyrolysis or combustion conditions. Thus in this work, a detailed thermodynamics and kinetic calculations were carried out to investigate the pre-intermediates formation for PCTA/PT/DTs from radial/molecule coupling of 2-C(T)P with their key radical species. Our study found that the radial/molecule mechanism can thermodynamically and kinetically contribute to the gas-phase formation of PCTA/PT/DT/s. The S/C coupling modes to form thioether-(thio)enol intermediats are preferable over the O/C coupling modes to form ether-(thio)enol intermediats. Thus, although the radial/molecule coupling of chlorophenoxy radical with 2-C(T)P have no effect on the PCDD/PTs formation, the radial/molecule coupling of chlorothiophenoxy radical with 2-C(T)P play an important role in the PCDT/PT formation. Most importantly, the pre-PCDT intermediates formation pathways from the coupling of sulfydryl/hydryl-substituted phenyl radical with 2-C(T)P and the coupling of (thio)phenoxyl diradicals with 2-C(T)P are more favorable to pre-PCTA/PT intermediates formation pathways from the coupling of chlorothiophenoxy radical with 2-C(T)P, which can give reasonable explanation for the high PCDT-to-PCTA ratio in the environment.

The cyclic load applied to civil and mining structures can lead to a reduction of the materials’ strength, different from that which would occur with a monotonous load. Numerous cases can be found where the decay of the rock parameters subjected to this type of stress leads to progressive or sudden collapse: among them, tunnel walls, pillars and slabs in mining operations, roads with a heavy vehicle transit, abutments of bridges and dams can be quoted. The topic can therefore be fundamental for a correct structural design, to avoid problems during the life of the structure. However, given the heterogeneity of the rock materials and the difficulty of their characterization under this aspect, an unequivocal analysis is hardly achievable. Then, the discussion initially develops through a general historical review of the concept of fatigue, with a synthetic collection of case histories. The laboratory tests on rock samples are then examined and the most important results obtained are discussed. Finally, a comparison between different types of tests is proposed. The experimental data are expressed through the Wӧhler diagram. The goal is to fill the lack of design codes or standards in the field of cyclic stresses applied to rock materials, the understanding of its effect being of great interest in order to apply suitable parameters in the design phase.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

Electrochemical-mechanical interactions, in particular pressure-induced ones, have been identified to be a cause for lithium-plating in lithium-ion cells. Mechanically-induced porosity inhomogeneities in the separator layers due to electrode expansion during charging especially lead to cell internal balancing currents and can cause localized plating. To identify cell-format and cell-material dependent mechanical weak spots, a layer-resolved mechanical simulation of different cell types and cell-material combinations is presented in this work. The simulation results show distinctive layer strain patterns for different cell-types that coincide with localized lithium-plating found in post-mortem cells. Additionally, the effects of cell bracing in battery modules is investigated and a method to mitigate the increased layer strain due to bracing counterforces is proposed that also increases cell energy density for hardcase-type automotive cells.

1) Background: Ultrasound-based strain imaging is now available in several ultrasound (US) scanners. Strain ratio (SR) can be used to quantify strain recorded simultaneously in two different user-selected areas, ideally exposed to the same amount of stress. The aim of this study was to evaluate SR variability when assessed in an in-vitro setup with a tissue-mimicking phantom, on resected tissue samples and in live tissue scanning with endoscopic applications. 2) Material and methods: Retrospective analysis of SR for quantification of elastic contrasts in a tissue-mimicking phantom containing four homogenous inclusions, in 38 resected bowel wall lesions and in 48 focal pancreatic lesions examined in vivo. Median SR and the inter-quartile range (IQR) was calculated on all external and endoscopic US-applications. The IQR/median provides a measure of the SR variability focusing on the two percentiles of the data closest to the median value. 3) Results: The overall variability of SR was lowest in a tissue-mimicking phantom (mean QR/median SR: 0.07). In resected bowel wall lesions representing adenomas, adenocarcinomas or Crohn lesions, the variability increased (mean IQR/Median: 0.62). During an endoscopic examination of focal pancreatic lesions in vivo, the variability increased further (mean IQR/Median: 2.04). 4) Conclusion: SR variability increased when assessed on different targets with growing heterogeneity and biological variability as one moved from homogeneous media to live tissues and endoscopic application. This may indicate a limitation for the accuracy SR evaluation in clinical applications.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

Assessment of drugs toxicity and associated biomarker genes is one of the most important tasks in the pre-clinical phase of drug development pipeline as well as in the toxicogenomic studies. There are few statistical methods for the assessment of doses of drugs (DDs) toxicity and their associated biomarker genes. However, these methods consume more time for computation of the model parameters using the EM (Expectation-Maximization) based iterative approaches. To overcome this problem, in this paper, an attempt is made to propose an alternative approach based on hierarchical clustering (HC) for the same purpose. There are several types of HC approaches whose performance depends on different similarity/distance measures. Therefore, we explored suitable combinations of distance measures and HC methods based on Japanese Toxicogenomics Project (TGP) datasets for better clustering/co-clustering between DDs and genes as well as to detect toxic DDs and their associated biomarker genes. We observed that Word’s HC method with each of Euclidean, Manhattan and Minkowski distance measures produces better clustering/co-clustering results. For an example, in case of glutathione metabolism pathway (GMP) dataset LOC100359539/Rrm2, Gpx6, RGD1562107, Gstm4, Gstm3, G6pd, Gsta5, Gclc, Mgst2, Gsr, Gpx2, Gclm, Gstp1, LOC100912604/Srm, Gstm4, Odc1, Gsr, Gss are the biomarker genes and Acetaminophen_Middle, Acetaminophen_High, Methapyrilene_High, Nitrofurazone_High, Nitrofurazone_Middle, Isoniazid_Middle, Isoniazid_High are their regulatory (associated) DDs explored by our proposed co-clustering algorithm based on the distance and HC method combination Euclidean: Word. Similarly, for the PPAR signaling pathway (PPAR-SP) dataset Cpt1a, Cyp8b1, Cyp4a3, Ehhadh, Plin5, Plin2, Fabp3, Me1, Fabp5, LOC100910385, Cpt2, Acaa1a, Cyp4a1, LOC100365047, Cpt1a, LOC100365047, Angptl4, Aqp7, Cpt1c, Cpt1b, Me1 are the biomarker genes and Aspirin_Low, Aspirin_Middle, Aspirin_High, Benzbromarone_Middle, Benzbromarone_High, Clofibrate_Middle, Clofibrate_High, WY14643_Low, WY14643_High, WY14643_Middle, Gemfibrozil_Middle, Gemfibrozil_High are their regulatory DDs. These results are validated by the available literature and functional annotation.

A new attack against the Kirchhoff-Law-Johnson-Noise (KLJN) key distribution system is introduced. The attack is based on 1) Utilizing the dc-voltage-source - which we put at Alice’s end in our mathematical modeling of the attack-that could exist due to errors, imbalances, Electromagnetic interference and etc.2) On studying the number of samples per bit in the security key that the measured Alice/Bob voltages exceeds or falls below a threshold voltage, respectively. The threshold voltage is the average between dc voltages across low and high resistors- generated by a dc-voltage source. We count the number of samples the voltage at Bob’s end (containing both the noise and dc components) exceeds the threshold voltage and how many times it falls below the threshold to judge whether the resistor can be guessed as low or high for every cycle. Also for a pre-specified key-length we count the number of high resistance estimations per bit –at Bob’s end-according to the previous criterion and the non-successful estimations per bit to judge the final guessed resistor value at Alice’s end and Bob’s end, where if we have more bits with most of its measured samples are above the threshold voltage then we will predict Bob’s resistance as high resistance, otherwise we predict Bob’s resistance to be low resistance. The Simulation was conducted and the attack proved that it is successful unless the temperature increased dramatically to ranges more than a threshold temperature ~ Kelvin that increases when the number of samples per bit increases.

The high mutation rate of human immunodeficiency virus type 1 (HIV-1) plays a major role in treatment resistance from the development of vaccines to long-lasting drugs. In addressing the crux of the issue, various attempts to estimate the mutation rate of HIV-1 resulted in a large range of 10-5 - 10-3 errors/bp/cycle due to the use of different types of investigation methods. In this review, we discuss the different assay methods, their findings on the mutation rates of HIV-1 and how the location of these mutations can be further analyzed for their potential allosteric effects to reveal potentially new inhibitors with different pharmacodynamics that can be used to circumvent fast occurring HIV drug resistance. Given that HIV is one of the fastest mutating viruses, it is a good model for comprehensive study of its mutations that can give rise to much horizontal understanding towards overall viral drug resistance as well as emerging viral diseases.

Growing agricultural demands for the global population are unlocking the path to developing innovative solutions for efficient water management. Herein, an intelligent variable rate irrigation system (fuzzy-VRI) is proposed for rapid decision-making to achieve optimized irrigation in various delimited zones. The proposed system automatically creates irrigation maps for a center pivot irrigation system for a variable-rate application of water. Primary inputs are spatial imagery on remotely sensed soil moisture (SSM), soil adjusted vegetation index (SAVI), canopy temperature (CT), and nitrogen content (NI). To eliminate localized issues with soil characteristics, we used the crop nitrogen content map to provide a focused insight on issues related to water shortage. The system relates these inputs to set reference values for the rotation speed controllers and individual openings of each central pivot sprinkler valve. The results showed that the system can detect and characterize the spatial variability of the crop and further, the fuzzy logic solved the uncertainties of an irrigation system and defined a control model for high-precision irrigation. The proposed approach is validated through the comparison between the recommended irrigation and actual irrigation at two field sites, and the results showed that the developed approach gives an accurate estimation of irrigation with a reduction in the volume of irrigated water of up to 27% in some cases. Future research should implement the fuzzy-VRI real-time during field trials in order to quantify its effect on irrigation use, yield, and water use efficiency.

Insufficient mixing in large-scale bioreactors, provokes gradient zones of substrate, dissolved oxygen, pH and other parameters. E. coli responds to a high glucose, low oxygen feeding zone with the accumulation of mixed acid fermentation products, especially formate, but also with the synthesis of non-canonical amino acids, such as norvaline, norleucine and -methyl-norleucine. These amino acids can be mis-incorporated into recombinant products, which causes a problem for pharmaceutical production whose solution is not trivial. While these effects can also be observed in scale down bioreactor systems, these are challenging to operate. Especially the high-throughput screening of clone libraries is not easy, as fed-batch cultivations would need to be controlled via repeated glucose pulses with simultaneous oxygen limitation, as has been demonstrated in well controlled robotic systems. Here we show that not only glucose pulses in combination with oxygen limitation can provoke the synthesis of these non-canonical branched-chain amino acids, but also that pyruvate pulses produce the same effect. Therefore we combined the enzyme based glucose delivery method Enbase® in a PALL24 mini-bioreactor system and combined repeated pyruvate pulses with simultaneous reduction of the aeration rate. These cultivation conditions, produced an increase in the non-canonical branched chain amino acids norvaline and norleucine in both the intracellular soluble protein and inclusion body fractions with mini-proinsulin as an example product, and this effect was verified in a 15 L stirred tank bioreactor. To our opinion this cultivation strategy is easy to apply for the screening of strain libraries under standard laboratory conditions if no complex robotic and well controlled parallel cultivation devices are available.

In this study, we report a new epoxy acrylate based shape memory polymer(SMP) fabricated by Liquid crystal display (LCD) Stereolithographic 3D printing. The printed 3D object has a high resolution and high transparency in visible light region. The uniaxial tensile tests showed enhanced tensile toughness and tunable mechanical properties. The fix-recovery and cycle tests indicated high shape recovery properties including high shape recovery rate and excellent cycling stability. In addition, a smart electrical valve actuator was fabricated that can be used in fast heat or electricity responsive electrical circuits. LCD 3D printing provides a low-cost and high efficient way to fabricate fast responsive SMP, which can be used in wide applications in various fields on aerospace engineering, biomedical devices, soft robots and electronic devices.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

The livestock sector can be a major contributor to the mitigation of greenhouse (GHG) emissions. Within the sector, beef production produces the largest proportion of the livestock sector’s direct emissions. The objective of this study was to assess the on-farm GHG emissions in semi-arid rangelands in Argentina and to identify the relationships between emissions and current farm management practices. A survey recorded detailed information on farm management and characteristics. Assessments of GHG emissions were based on the IPCC Tier 2 protocols [1]. The relationships between farm management and GHG emissions were identified using General Linear Models. Cluster analysis was used to identify groups of farms that differed from others in emissions and farm characteristics. Emissions per product sold were low on farms that had improved livestock care management, rotational grazing, received technical advice, and had high animal and land productivities. Emissions per hectare of farmland were low on farms that had low stocking rates, low number of grazing paddocks, little or no land dedicated to improved pastures and forage crops, and low land productivity. Our results suggest that the implementation of realistic, relatively easy-to-adopt farming management practices has considerable potential for mitigating GHG emissions in semi-arid rangelands of central Argentina.

With a low rate of new building construction and insufficient rate of existing building renovation, there is the need for stepping up the pace of building renovation with ambitious performance targets to achieve EU climate change policies. However, effective technologies alone cannot solve the low renovation rate of existing buildings in Europe that is hindering the reaching of EU-wide targets. A workshop was held at the Sustainable Place Conference 2018 to present successful experiences with an integrative approach from H2020 innovation actions (4RinEU, P2ENDURE, Pro-GET-OnE, MORE-CONNECT) aiming at improving building energy performance through deep renovation. This article presents the outcomes of the joint workshop and interactive discussion, by focusing on the different technical, financial and social added values, barriers and challenges in building renovation as well as on the identification of open questions to address future innovation opportunities.

The aim of the studies was to test the hydraulic pressure losses along the length, local pressure losses, absolute and relative roughness values of the pipeline walls made of modern polymer material. The article presents the results of the experimental studies of hydraulic resistance of pipelines from modern polymer materials, the method of theoretical determination of resistance coefficients in the VALTEC ISO 21003 metal polymer pipeline, the classification and method of determining the values of local hydraulic resistance coefficients of T-Junctions are given, the dependence for determining the Darcy λ hydraulic friction coefficient associated with the value of the equivalent hydraulic roughness coefficient of the inner surface of pipes and the Reynolds number. The experimental data of the hydraulic coefficient of friction Darcy λ was compared with the known theoretical relationships of A.D. Altschul, Colbrooke for smooth pipes, Colbrooke and White, an alternative to the Colbrooke-White, Offengenden equation for low-shear pipes and pipes from polymer materials with Reynolds numbers Re>10^4. Dependence of hydraulic coefficient of friction on relative equivalent roughness of pipeline walls and Reynolds number, specific energy loss per one linear meter on total flow rate in system of hydraulically short pipeline is obtained. The empirical dependence of values of coefficients of local resistance ζ=f(Q2/Q3) from a ratio of the divided expenses of Q2/Q3 of the equal-pass T-Junction α=90 the pipeline to a branch up, on pass in the direct T-Junction and division of streams at various internal pipeline diameters of VALTEC.

Global research on the Covid-19 vaccine’s effectiveness is using methods that are misleading the scientific community and public opinion. There is a golden rule in medicine: to measure the effectiveness of an experimental medicine you need to have two groups. The group that will take medicine and the group that will not take medicine. You follow the health status of both groups for a few months and you will get objective results. This is the only proper methodology to verify the effectiveness of a new medicine. Articles cited from 1-5 did not use the gold rule. They develop different kinds of methodologies that all have no statistical significance. On the basis of their methodologies, they conclude that Covid-19 vaccines have a positive effect on public health. By comparing graphs of the intensity of vaccination and the rate of mortality we see that after the period of intense vaccination follows the period of higher excess mortality. Basic statistical data are confirming that Covid-19 vaccines increased the mortality rate.

Currently, old-style personal medicare techniques rely mostly on traditional methods, such as cumbersome tools and complicated processes, which can be time-consuming and inconvenient in some circumstances. Furthermore, such old methods need the use of heavy equipment, blood draws, and traditional bench-top testing procedures. Invasive ways of acquiring test samples can potentially cause patients discomfort and anguish. Wearable sensors, on the other hand, may be attached to numerous body areas to capture diverse biochemical and physiological characteristics as a developing analytical tool. Physical, chemical, and biological data transferred via the skin is used to monitor health in various circumstances. Wearable sensors can assess the aberrant conditions of the physical or chemical components of the human body in real-time, exposing the body state in time, thanks to unintrusive sampling and high accuracy. Most commercially available wearable gadgets are mechanically hard components attached to bands and worn on the wrist, with form factors ultimately constrained by the size and weight of the batteries required for the power supply. Wearable gadgets with “skin-like” qualities are a new type of automation that is only starting to make its way out of research labs and into pre-commercial prototypes. In this paper, we studied the recent advancement in battery-powered wearable sensors established on optical phenomena and skin-like battery-free sensors which brings a breakthrough in wearable sensing automation.

In this paper we investigate the global asymptotic stability of following system ofhigher order difference equations with quadratic terms:xn+1=A+Byn/yn−m^2, yn+1=A+Bxn/xn−m^2, where A and B are positive numbers and the initial values are positive numbers.We also study the boundedness, rate of convergence and oscillation behaviour of thesolutions of related system.

Single-molecule fluorescence detection (SMFD) experiments are useful in distinguishing sub-populations of molecular species when measuring heterogeneous samples. One experimental platform for SMFD is based on a confocal microscope, where molecules randomly traverse an effective detection volume. The non-uniformity of the excitation profile and the random nature of Brownian motion, produce fluctuating fluorescence signals. For these signals to be distinguished from the background, burst analysis is frequently used. Yet, the relation between the results of burst analyses and the underlying information of the diffusing molecules is still obscure and requires systematic assessment. In this work we performed three-dimensional Brownian motion simulations of SMFD, and tested the positions at which molecules emitted photons that passed the burst analysis criteria for different values of burst analysis parameters. The results of this work verify which of the burst analysis parameters and experimental conditions influence both the position of molecules in space when fluorescence is detected and taken into account, and whether these bursts of photons arise purely from single molecules, or not entirely. Finally, we show, as an example, the effect of bursts that are not purely from a single molecule on the accuracy in single-molecule Förster resonance energy transfer measurements.

In this study, the model proposed by Yang et al. to generalize the stress–strain model for unconfined concrete with consideration of the size effect is expanded. Sim et al.’s compressive strength model that is based on the function of specimen width and aspect ratio was used for the maximum stress. In addition, a strain at the maximum stress was formulated as a function of compressive strength by considering the size effect using the regression analysis of datasets compiled from a wide variety of specimens. The descending branch after the peak stress was formulated with consideration of less dissipated area of fracture energy with the increase in specimen width and aspect ratio in the compression damage zone (CDZ) model. The key parameter for the slope of the descending branch was formulated as a function of specimen width and aspect ratio, concrete density, and compressive strength of concrete considering the size effect. Consequently, a rational stress–strain model for unconfined concrete was proposed. This model explains the trends of the peak stress and strain at the peak stress to decrease and the slope of the descending branch to increase, as the specimen width and aspect ratio increase. The proposed model agrees well with the test results, irrespective of the compressive strength of concrete, concrete type, specimen width and aspect ratio. In particular, the proposed model for the stress–strain curve rationally considered the effect of decreasing peak stress and increasing the descending branch slope, with the increase in specimen width and aspect ratio.

The kinetics and optimal efficacy conditions of photoinitiated polymerization are theoretically presented. Analytic formulas are derived for the crosslink time, crosslink depth and efficacy function. The roles of photosensitizer (PS) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented . For optimal efficacy, a strategy via controlled PS concentration is proposed, where re-supply of PS in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced.

Because of an often complicated and difficult-to-access care system, help-seeking for people with suspected dementia can be stressful. Difficulty in help-seeking may contribute to carer burden, in addition to other known stressors in dementia care. This study examined the relationship between perceived help-seeking difficulty and carer burden, and the barriers contributing to perceived difficulty. We interviewed 110 carers accessing a community-based dementia assessment service for suspected dementia of a family member for their perceived difficulty, delays, and barriers in help-seeking, and carers burden in terms of role strain, self-criticism, and negative emotions. Linear regression models showed that perceived help-seeking difficulty is associated with carer self-criticism, while carer role strain and negative emotions are associated with symptom severity of the person with dementia but not help-seeking difficulty. Inadequate knowledge about symptoms, service accessibility, and affordability together explained more than half of the variance in perceived help-seeking difficulty (Nagelkerke R2 = .56). Public awareness about symptoms, support in navigating service, and financial support may reduce perceived difficulty in help-seeking, which in turn may reduce carer self-criticism during the early course of illness.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

We try to solve three decades-old physics challenges. List all elementary particles. Describe dark matter. Describe mechanisms that govern the rate of expansion of the universe. We propose new modeling. The modeling uses extensions to harmonic oscillator mathematics. The modeling points to all known elementary particles. The modeling suggests new particles. Based on those results, we do the following. We explain observed ratios of dark matter amounts to ordinary matter amounts. We suggest details about galaxy formation. We suggest details about inflation. We suggest aspects regarding changes in the rate of expansion of the universe. We interrelate the masses of some elementary particles. We interrelate the strengths of electromagnetism and gravity. Our work seems to offer new insight regarding applications of harmonic oscillator mathematics. Our work seems to offer new insight regarding three branches of physics. The branches are elementary particles, astrophysics, and cosmology.

Immunity has become an important aspect of concern, as the spread of corona virus, is on the rise. The strategies to boost and modulate the immunity have therefore become need of the hour. The present study was carried out to evaluate the effect of Charak immunity Tablets (CIT) on innate and adaptive immune response in healthy individuals. It was a single-blind, randomized, placebo-controlled, exploratory study. After obtaining Ethics Committee permission, 36 healthy individuals of either sex aged 18-35 years with prior consent were recruited in the study. They were randomly divided into 2 groups to receive either CIT or Placebo in 2:1 ratio. Both the interventions were given in a dose of 1 tab (500 mg) twice daily. The assessment variables were vitals [temperature, pulse, and blood pressure], respiratory health [respiratory rate, oxygen saturation and peak expiratory flow rate], questionnaire based assessment of immune status, perceived stress and quality of life along with objective assessment of immunity [CD4+, CD8+ counts, Interferon gamma (IFN γ), Tumor necrosis factor alpha (TNF-α) and Interleukin 10 (IL-10)] as well as oxidative stress; [Malondialdehyde (MDA) and Glutathione peroxidase], which were assessed at fixed time points. Of 36 recruited participants, only 18 participants completed the study. CIT treated individuals showed a statistically significant improvement in respiratory health, quality of life, perceived stress and subjective immune status. There was a decrease in the levels of serum IFN γ on day 60 compared to baseline. TNF-α and IL-10, both estimated from supernatant of Peripheral Blood Mononuclear Cells (PBMCs) stimulated with lipopolysaccharide (LPS), showed a decrease and a significant increase respectively on day 60 compared to baseline in CIT group. Further, CIT significantly decreased MDA levels.The present study indicates that CIT is an effective and safe drug to boost immunity. However, our findings need to be confirmed in larger sample size using more specific immune parameters.

The energy efficiency of grinding depends on the appropriate selection of cutting conditions, grinding wheel and workpiece material. Additionally, the estimation of specific energy consumption is a good indicator to control the energy consumed during the grinding process. Consequently, this study develops a model of material removal rate to estimate the specific energy consumption based on the measurement of active power consumed in a plane surface grinding of C45K with different thermal treatments and AISI 304. This model identifies and evaluates the power dissipated by sliding, ploughing and chip formation in a industrial-scale grinding process. Furthermore, the instantaneous positions of the abrasive grains during cutting are described to study the material removal rate. The estimation of specific chip formation energy is similar to that described by other authors in laboratory scale, which allows to validate the model and experiments. Finally, the results show that the energy consumed by sliding is the main phenomenon of energy dissipation in industrial-scale grinding process, where it is denoted that sliding energy by volume unity decreases as the depth of cut and speed of workpiece increase.

Canopy characteristics are crucial for accurately and safely determining the pesticide quantity and volume of water used for spray applications in vineyards. The inevitably high degree of intra-plot variability makes it difficult to develop a global solution for the optimal volume application rate. Here, the design procedure of, and the results obtained from, a variable rate application (VRA) sprayer are presented. Prescription maps were generated after detailed canopy characterization, using a multispectral camera embedded on an unmanned aerial vehicle, throughout the entire growing season in Torrelavit (Barcelona) in four vineyard plots of Chardonnay (2.35 ha), Merlot (2.97 ha), and Cabernet Sauvignonn (4.67 ha). The maps were obtained by merging multispectral images with information provided by DOSAVIÑA®, a decision support system, to determine the optimal volume rate. They were then uploaded to the VRA prototype, obtaining actual variable application maps after the application processes were complete. The prototype had an adequate spray distribution quality and exhibited similar results in terms of biological efficacy on powdery mildew compared to conventional (and constant) application volumes. The VRA results demonstrated an accurate and reasonable pesticide distribution, with potential for reduced disease damage even in cases with reduced amounts of plant protection products and water.

Background: To date, FM using middle ear packing has rarely reported. In this study, we hypothesized that middle ear packing with dexamethasone soaked gelfoam and fibrin glue over the fat graft could promote the success rate of TMP closure regardless of perforation size. Methods: Between January 2005 and July 2020, a total of 209 patients who underwent fat myringoplasty due to chronic TMP at tertiary referral center were encountered and analyzed. The success rate and audiologic outcome was analyzed. Results: The mean successful TM closure rate was 88.0 %. The success rate by different age generation was not significant difference. The size of the perforation grade showed no significant difference. The perforation site by anterior or posterior was not significant. The preoperative mean threshold of AC, BC and ABG were 55.71, 12.98 and 42.73 dB respectively. The postoperative mean threshold of AC, BC and ABG were 23.67, 12.98 and 10.69 dB. The change of preoperative and postoperative hearing showed statistically significant. Conclusion: From our results, the simple trimming of the perforation edge and middle ear packing with external ear canal packing using fibrin glue induced the stable adhesion between the remnant TM and the fat graft.