A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

The many limitations of implementing anticancer strategies under the term “precision oncology” have been extensively discussed. While some authors propose promising future directions, others are less optimistic and use phrases such as illusion, hype and false hypotheses. The reality is revealed by practicing clinicians and cancer patients in various online publications, one of which has stated that “in the quest for the next cancer cure, few researchers bother to look back at the graveyard of failed medicines to figure out what went wrong.” The message is clear: novel therapeutic strategies with catchy names (e.g., synthetic “lethality”) have not fulfilled their promises despite decades of extensive research and clinical trials. The main purpose of this review is to discuss key challenges in solid tumor therapy that surprisingly continue to be overlooked by the nomenclature committee on cell death and numerous other authors. These challenges include: the impact of chemotherapy-induced genome chaos (e.g., multinucleation) on resistance and relapse, oncogenic function of caspase 3, cancer cell anastasis (recovery from late stages of apoptosis), and pitfalls of ubiquitously used preclinical chemosensitivity assays (e.g., cell “viability” and tumor growth delay studies in live animals) that score such pro-survival responses as “lethal” events. Studies outline herein underscore the need for new direction in the management of solid tumors.

Soil water content (SWC) and soil organic carbon (SOC) are two important factors to consider when revegetation in degraded land of arid and semiarid areas. Knowing the response of SWC and SOC to vegetation restoration as well as their coupling interaction is important for sustainability of vegetation restoration. In this study, three common plantations of the same recovery years were selected on China’s Loess Plateau, which included Pinus sylvestris, Pinus tabuliformis and Populus simonii, to evaluate the response of SWC and SOC to vegetation restoration as well as their interactions, and then revealed the influencing factors of SWC and SOC variations. Results showed that compared to the grassland, three plantations all exacerbated the deficit of deep soil water, but Populus simonii increased the SOC, while the rest all decreased the SOC. And tradeoff of Populus simonii had the lowest root mean squared error (RMSD). Therefore, Populus simonii was identified as representing a suitable revegetation technique for this region. There was strong interaction between SWC and SOC for shallow soil layers. Land use type (LUT) has an important effect on deep SOC variations, while SOC and soil texture for deep SWC variations. The results were helpful to the sustainable development of artificial forests in this region as well as other similar arid and semiarid areas.

The problem of normal impact of a rigid sphere onto a Maxwell viscoelastic solid half-space is considered. The first-order asymptotic solution is constructed in the framework of Hunter’s model of viscoelastic impact [Hunter, S. C., 1957. Energy absorbed by elastic waves during impact. Journal of the Mechanics and Physics of Solids, 5(3), 162–171.]. In particular, simple analytical approximations have been derived for the maximum contact force and the time to achieve it. A linear regression method is suggested for evaluating the instantaneous elastic modulus and the mean relaxation time from a set of experimental data collected for different impactors and impact velocities.

The emphasis in the automotive industry towards sustainable mobility has led to a significant interest in hybrid-electric propulsion systems with high energy density batteries. Addressing the needs of this strategy, the battery market is exploring new technologies to improve the safety and lifespan of electric vehicles. To this end, there is a focus on the all-solid-state battery (ASSB) technology for its cycle capabilities. Filling the current void in the literature pertaining to accurate ageing models for ASSBs, in this work, we present an enhanced version of the numerical ageing model, originally developed for liquid electrolyte based batteries, to forecast the development of the solid electrolyte interface layer that is the major cause of battery capacity fading. The model has been tested on prototype batteries and reveals an accuracy of 99%. The capacity fade in ASSBs has been investigated under different conditions, and the enhanced ageing model has been validated using experimental data from these batteries. The findings suggest that there is potential for solid-state batteries to be commercialized, although significant work is needed to match the manufacturing level of lithium-ion batteries with liquid electrolytes.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

Pulverized coal pyrolysis based on solid heat carrier has a huge advantage in high tar yield. In this study, pyrolysis experiments of pulverized coal were conducted in a lab-scale fluidized bed reactor at 650 ℃, utilizing char as the solid heat carrier. The influence of mass ratio of char to coal (RATIO) was investigated. Results show that the incorporation of solid heat carrier of char significantly enhanced the initial reaction in coal pyrolysis, resulting in increasing yields of tar and gas but reducing one of char. The yield of tar maximally reached 148.80-262.22% of the Gray-King analysis value at the RATIO of 14.52 g/g. As the RATIO increased, the tar contained more light component content, indicating that incorporating solid heat carriers improved the tar quality. These findings offer significant insights for the design of fluidized bed pyrolysis unit utilizing char as solid heat carrier.

Facial acne is a prevalent dermatological condition regularly observed in the general population. This study introduces a novel deep learning model for facial acne segmentation utilizing a semi-supervised learning method known as bidirectional copy-paste, which synthesizes images by interchanging foreground and background parts between labeled and unlabeled images during the training phase. To overcome the lower performance observed in the labeled image training part compared to the previous methods, a new framework was devised to directly compute the training loss based on labeled images. The effectiveness of the proposed method was evaluated against previous semi-supervised learning methods using images cropped from facial images at acne sites. The proposed method achieved a Dice score of 0.5205 in experiments utilizing only 3% of labels, marking an improvement of 0.0151 to 0.0473 Dice score over previous methods. The proposed semi-supervised learning approach for facial acne segmentation demonstrates improvement in performance, offering a novel direction for future acne analysis.

The primary objective of this current study is to conduct a comprehensive review of existing literature that discusses research on post and core restorations, covering aspects such as their composition, manufacturing methods, and clinical effectiveness. The methodology employed in this review encompasses the implementation of a well-defined search strategy, the establishment of criteria for inclusion and exclusion, and the selection of relevant studies to summarize their findings. To gather relevant literature published between 1993 and 2023, the research team conducted separate searches on PubMed, Scopus, and Embase databases. In total, 165 titles were initially retrieved from these electronic databases. By applying the predefined exclusion criteria, the researchers identified 73 articles that specifically address the conventional and computer-aided design/computer-aided manufacturing (CAD/CAM) technologies employed in post and core restorations. These restorations are frequently utilized procedures for repairing teeth that have undergone endodontic treatment and subsequently lost dental structure. The development of computerized technology for the creation of customized posts and cores has emerged as a straightforward and efficient alternative to traditional methods. The review encompasses a synthesis of papers discussing the various techniques and materials employed in constructing post and cores using CAD/CAM technology. Notably, different strategies for restoring endodontically treated teeth through CAD/CAM post and cores have been documented, revealing both direct and indirect approaches. The most mentioned materials for these restorations include zirconia, composite resin, and hybrid ceramics. While the available literature on CAD/CAM post and core procedures is somewhat limited, the review underscores the need for further research to explore the long-term outcomes and efficacy of this treatment approach.

Leishmaniasis in wild canids is a vector-borne disease caused in Europe by the protozoan parasite Leishmania infantum. To date, there is limited information on clinical signs and laboratory abnormalities in wolves due to leishmaniasis. The current clinical case report described a female Iberian wolf (Canis lupus signatus) housed in semi-captivity conditions at the Centro del Lobo Ibérico “Félix Rodríguez de la Fuente”, in Robledo de Sanabria, Zamora (Spain) with an interdigital ulcerous wound at the right forepaw, hyper-gammaglobulinemia, and abnormal liver blood parameters. Definitive serodiagnosis of leishmaniasis was established using antileishmanial serum antibodies and PCR analysis of different biological samples. A gold standard anti-L. infantum treatment protocol consisting in intramuscular meglumine antimoniate and oral allopurinol combination was installed. However, the presence of pain at the site of injection due to meglumine antimoniate administration forced its substitution by oral miltefosine. A progressive reduction of the levels of anti-L. infantum serum antibodies and the concentrations of gamma-globulin fraction was detected after antileishmanial treatment as well as a decline of liver GPT. To our knowledge, this is the first case of leishmaniasis diagnosed in a wolf housed in semi-captivity conditions treated and successfully cured.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.

The German health authorities' guidelines for medical devices in 2012 highlighted the importance of cleaning ultrasound probes, emphasizing their validation and reliability. In addition to automated and validated options, alternative manual methods such as wipe disinfection have gained traction due to their independence from additional hardware. The study examines the effectiveness of manual disinfection methods, specifically the cleaning process, addressing concerns raised by the Robert Koch Institute regarding the lack of validation for wipe disinfection of semi-critical devices. The EQUINOS colored wipe disinfection kit identified wetting gaps in all cleanings across four probes tested. The results indicate significant challenges in ensuring complete surface wetting, particularly in complex body parts such as clip-on areas and shapes for additional biopsy attachments, suggesting that manual methods alone may not adequately mitigate the risk of infection transmission (p value .001). The study concludes that while manual disinfection methods are a viable alternative to automated reprocessing, there is a critical need for enhanced training and potentially the development of more effective manual disinfection techniques or colored wipes to ensure patient safety and compliance with healthcare hygiene standards.

Environmental degradation leads to a totally unsustainable food system. In addition to this is-sue, the consumption of foods that improve people's health and well-being is recommend-ed. These guidelines create new challenges and the demand for alternatives to meet these needs in the short term. One of the alternatives is undoubtedly the use of by-products of winemaking, namely in the form of grape pomace flour (GPF), which is obtained in a totally sustainable way, requires no further water consumption or agricultural land, and is an ingredient that boasts all the characteristics that meet the circular economy and has colossal potential in promoting nutrition and healthy eating. To verify the benefits of using the Touriga Nacional and Arinto (Vitis vinifera L.) flour varieties, analytical determinations were made to identify and quantify different components, such as nitrogen and extractable phosphorus, ash, moisture, proteins, fats, dietary fibers, total sugars, and phenolic content. GPF could become a valuable ingredient due to its nutritional quality and high content in various polyphenols namely flavonoids and pyranoanthocyanins.

The objective of this research was to study the dynamics of moisture and nutrition at the root zone and to quantify the variables linked to efficient water management in avocado orchards of mid and high-lands of Michoacán, México, in typical Andisols of low fertility with (A)C(w2) and C(w2) climates, respectively. Using the FDR (Frequency Domain Reflectometry) technology, the dynamics of soil moisture and salinity were recorded daily at four depths: 0-15, 15-30, 30-45, and 45-60 cm. The soil moisture balance model was used to determine actual evapotranspiration (ETr), crop coefficient (Kc), and water use efficiency (WUE). Results indicated that ETr is 66-73% of the total water at 0-30 cm depth; the fertilizer absorption is limited to 0-30 cm, being negligible at deeper layers. The water use efficiency is 4.4 to 5.6 kg of fruit m-3 of applied water, and the ratio of the water use index (ETr/irrigation sheet applied, ISA) is 0.65-0.70; while the annual avocado Kc is 0.72 in Cutzato and 0.78 in Tiamba. We concluded that avocado has a low water requirement, it does not cause leaching of nutrients and/or water, the absorption of water and nutrients mostly occurs at 30 cm depth, and from a hydrological point of view, the crop is environmentally friendly.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Hypertensive disorders of pregnancy (HDP), including preeclampsia (PE) and gestational hypertension (GH), are major causes of maternal and fetal morbidity and mortality. This review elucidates the role of regulatory T cells (Tregs) in the immunological aspects of HDP and explores their therapeutic potential. Tregs, known for maintaining immune tolerance, are crucial in pregnancy to prevent immune-mediated rejection of the fetus. In HDP, Treg numbers and function imbalance are observed, correlating with disease severity. The review highlights that Tregs contribute to immunological adaptation in normal pregnancy, ensuring fetal acceptance and placental development. In contrast, HDP is associated with Treg dysfunction, marked by decreased numbers and impaired regulatory capacity, leading to inadequate immune tolerance and abnormal placental development. This dysfunction is particularly evident in PE, where Tregs fail to adequately modulate the maternal immune response against fetal antigens, contributing to the pathophysiology of the disorder. Therapeutic interventions aiming to modulate Treg activity represent a promising avenue for HDP management. Studies in animal models and limited clinical trials suggest that enhancing Treg functionality could mitigate HDP symptoms and improve pregnancy outcomes. However, the review acknowledges the complexity of translating these findings into effective clinical therapies, given the multifactorial nature of HDP and the intricate regulatory mechanisms of Tregs. In conclusion, while the precise role of Tregs in HDP is still being unravelled, their central role in immune regulation during pregnancy is indisputable. Further research is needed to fully understand the mechanisms by which Tregs contribute to HDP and to develop targeted therapies that can safely and effectively harness their regulatory potential for treating hypertensive diseases of pregnancy.

Understanding clinical significance of variants of unknown significance (VUS) reported in next-generation sequencing (NGS) has become essential in cancer treatment. Our study examined six widely used in silico tools: PolyPhen-2, Align-GVGD, MutationTaster2, CADD, REVEL, and Chat-GPT. We utilized a dataset of gene variants known to potentially affect immune therapy. No single tool could comprehensively determine mutation variant pathogenicity. MutationTaster2021 showed the highest overall accuracy and MCC among the tools. Notably, REVEL and Chat-GPT exhibited 100% specificity, suggesting their proficiency in accurately identifying pathogenic variants and minimizing false positives. In contrast, CADD displayed optimal sensitivity, making it suitable for effectively ruling out benign variants.

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

How hands-on gardening impacts behaviors including healthy eating and physical activity during early childhood can be of critical importance for preventing early onsets of obesity. This research investigates how participating in hands-on gardening impacts preschoolers’ (3-5 years old) physical activity (measured by accelerometers) in childcare centers in the Semi-Arid Climate Zone. The research was conducted in eight licensed childcare centers located in West Texas with 149 children (n=149). Four childcare centers in the experimental group received hands-on garden interventions; the other four in the control group did not. In both experimental (intervention) and control (non-intervention) centers, children wore Actigraph GT3X+ accelerometers continuously for 5 days before and for 5 days after intervention (a total of 10 days). Results show that the duration of sedentary behavior of children in the experimental (intervention) group significantly decreased compared to children in the control (non-intervention) group. The finding suggests that the positive effects of childcare hands-on gardening on physical activity extend to semi-arid climate zones where gardening is challenging due to high temperatures and lack of annual rainfall. The research emphasizes the critical need to incorporate hands-on gardening in childcare centers as an obesity prevention strategy nationally in the U.S. and beyond.

Solid-state fermentation (SSF) is the bioprocess where microorganisms are cultivated in the absence of free water under control conditions. Lactic acid can be produced by fermenting grape stalks with Rhizopus oryzae in SSF. During the microorganism growth, the temperature and water content of the solid bed fluctuate, leading to areas of either dry or excessive moisture in the solid substrate. Therefore, it's crucial to control the supply of water to the matrix. In this work, we obtain lactic acid through SSF of grape stalks using Rhizopus oryzae NCIM 1299. The SSF was conducted at a fixed temperature of 35 °C, with three constant relative humidity levels: 50, 65, and 80 %RH. Mathematical models, including the Logistic and First Order Plus Dead Time models for fungal biomass growth and the Luedeking and Piret with Delay Time model for lactic acid production, were adjusted to kinetic curves. Growth kinetic parameters (Xmax, μmax, Tp, T0, Yp/x and td) were determined for all conditions. These kinetic parameters were then correlated with relative humidity using a second-degree polynomial relationship. We observed a decrease in Xmax with increasing %RH, while the value of Yp/x increased at higher %RH. Finally, the optimal variable relative humidity profile was obtained by applying the Dynamic Optimization Technique, resulting in a 15.30% increase in lactic acid production.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

: Sputtering of silicon in a Helium magnetron discharge (MS) has been reported as a bottom-up procedure to obtain He-charged silicon films (i.e. He nanobubbles encapsulated in a silicon matrix). The incorporation of heavier noble gases is demonstrated in this work with a synergistic effect producing increased Ne and Ar incorporations when using He-Ne and He-Ar gas mixtures in the MS process. Microstructural and chemical characterizations are reported by ion beam analysis (IBA) and scanning and transmission electron microscopies (SEM and TEM). In addition to gas incorporation, helium promotes the formation of larger nanobubbles. For the case of Ne high resolution X-ray photoelectron and absorption spectroscopies (XPS and XAS) are reported with remarkable dependence of the Ne 1s photoemission and the Ne K-edge absorption on the nanobubbles size and composition. The gas (He, Ne, Ar) charged thin films are proposed as “solid” targets for the characterization of spectroscopic properties of noble gases in a confined state without the need for cryogenics or high-pressure anvils devices. Also their use as targets for nuclear reaction studies is foreseen.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

This investigation introduces an efficient method for assessing the reliability of semi-rigid steel frame connections in existing buildings, explicitly targeting the Top Angle and Seat Pad (TA-SP) semi-rigid connection commonly used in Australian cities' high-rise buildings. The moment capacity of these connections was examined through parameter power model testing, meticulously considering the bending, shear, and prying forces actions to determine the weakest elements in the connection system. A plastic hinge model was applied to ensure computational efficiency and accuracy in assessing the connections' ultimate strength. Comparatively, the finite element (F.E) method M−θ curves were introduced to scrutinise the nonlinear behaviour of the connection, providing validation for the predicted analytical approach. Further emphasis was placed on identifying the reliability of the weakest elements in the connection system, employing the First-Order and Second-Order Reliability Methods models to estimate their reliability index. The correlation between the model's failure probability and a percentile error was also explored, utilising Monte Carlo simulation reference for refined validation. Novel formulas and methodologies were introduced to compute the locked-chain-series system reliability, which accounts for the inherent material and geometric variability. The findings highlight the critical significance of the weakest element in determining the overall reliability of the existing TA-SP connection.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

The aim of this study is to solve the problems of complicated pretreatment and high analytical cost in the detection technology of trace drug toxicants in municipal wastewater. A high-performance magnetic sorbent was synthesized for enrichment of trace drug substances in wastewater to develop magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical methods for the molecules in wastewater drug toxicants. The magnetic nanospheres was successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinyl pyrrolidone.The results showed that the linear dynamic range of 17 drugs was 1-500 ng/L, the recovery was 43%-105%, the matrix effect was more than 67%, the limit of quantitative detection was 1-2 ng/L, and the detection time of each sample was 2.98s. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problem of complicated pre-treatment and analytical cost in the detection of drugs in wastewater. The developed magnetic material and acoustic excitation coupled mass spectrometry analysis method can realize the low-cost, efficient enrichment and fast analysis of different kinds of drug molecules in urban sewage.

The assessment of existing bridges constitutes a serious challenge for the researchers since their safety evaluation is a complex task due to several sources of uncertainty affecting the parameters identified in the knowledge process. In particular, a high level of uncertainties may arise in the case of prestressing systems requiring special investigation strategies and experimental technologies. The paper aims to investigate how the knowledge uncertainties influence the safety assessment of existing post-tensioned bridges. The semi-probabilistic approach is used, and uncertainties related to the knowledge process are described considering the number of tests, the confidence level assumed for the estimation of the problem parameters, and the measurement errors of in-situ tests. Results concerning a typical post-tensioned bridge are reported and the variability of the outcomes is discussed and compared with a reference case of “perfect knowledge”. The main results of the study confirm the general robustness of the semi-probabilistic Eurocodes safety format and provide an overview of dispersion due to different choices about the number of tests and confidence level. The measurement errors may lead to significant under-estimation of the computed structural capacity with respect to the reference one.

Due to the difficult metallurgical conditions during production, advanced processing techniques are required to produce functionally graded metal matrix composites. In this study, we explored a novel approach by using a combination of two different methods to produce Functionally Graded 7075 Al / SiCp composites. First process was direct semi-solid stirring that was used to prevent particle agglomeration, brittle reaction products, floating or settling of the reinforcements and poor wettability for the production of SiCp (wt. 5-20%) reinforced aluminum matrix composites. In the direct semi-solid mixing process, the matrix material remains in a semi-solid state until the reinforcement addition process is completed. The second novel process was sequential squeeze casting to provide liquid diffusion between two composite layers that were used to produce functionally graded aluminum matrix composite. The microstructure and interlayer zones were characterized by using optical microscopy and scanning electron microscopy. The resulting functionally graded material was subjected to spectrometer analyses, density measurements, and metallographic examinations in order to determine the characteristics of its layers and interfacial zones, as well as to assess the formation of the graded structure. The results obtained from this research provide the potential to use this new combined manufacturing method, which is relatively inexpensive, efficient and easily applicable, in order to produce functionally graded SiCp reinforced aluminum composites.

.(1) Background: Groundwater resources management in dry lands, characterized by climate var-iability and population growth, is difficult. Exploration and exploitation of groundwater, due to inadequate surface water is very costly. The present study employed Analytic Hierarchy Process (AHP) and GIS to identify Ground-Water Potential (GWP) areas in a semi-arid region of Nigeria; (2) Methods: Land-use-land-cover, drainage density, slope, rainfall, static water level, soil media, vadose media and aquifer media were selected for GWP analysis. Parameters weights were de-termined using AHP and ranked based on their contribution to GWP by experts. The parameters were then integrated using weighted overlay tool in ArcGIS 10.5 to produce GWP map of the study area. Boreholes yield data from 245 wells were collected to determine the model accuracy and model validation; (3) Results: Results classified the study area into very high GWP (1.9%), high GWP (8.8%), moderate GWP (62%), low GWP (20.70%) and very low GWP (6.6%). Validation of the AHP model with boreholes yield data shows a correlation coefficient of 71.3% giving a good prediction; (4) Conclusions: AHP and GIS can be used to successfully map GWP areas which could serve as an exploration guide for sustainable management of groundwater resources in semi-arid areas.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Matrices and their inverses allow accurate calculations to be produced quickly and compactly and can be used to control any process represented by a system of equations. Singular matrices require extensive workarounds (costing time and money) to solve these systems of equations because they have no inverse. Finding their inverse involves division by zero. Nevertheless, recently a new number set called semi-structured complex numbers was developed to enable division by zero in algebraic equations. The aim of this research was to demonstrate that the inverse of a singular matrix can be found using semi-structured complex numbers. This research reveals (1) Singular matrices and their inverses can be used to find a unique solution to a pair of simultaneous equations that appear to have infinitely many solutions or appear to have no solution; (2) Singular matrices map coordinates in projective space to coordinates in Euclidean space and their inverse maps coordinates in Euclidean space to coordinates in projective space; (3) the inverse of a singular matrix proves that parallel lines in Euclidean space do not intersect but in projective space intersect at a “point at infinity” and (4) collinear lines that intersect at infinitely many points in Euclidean space only intersect at one point in projective space.

Solid-liquid interfacial phenomena play an essential role in our everyday lives and are often regarded as the outcome of interactions at the solid-liquid interface. However, the intricately intrinsic mechanism underlying interfacial interactions renders in-situ simulations and direct measurements challenging. As an effective analytic method for studying solid-liquid interfacial interactions, Microcalorimetry can provide the most basic thermodynamic information (including changes in enthalpy, entropy, and Gibbs free energy during solid-liquid binding/separation processes), which is extremely crucial for understanding interaction directionality and limitation. This review is dedicated to highlighting the pivotal role of microcalorimetry in studying solid-liquid immersion and adsorption processes. Specifically, we provide an overview of the commonly employed microcalorimetric methods, delve into the influence factors of enthalpy change, and finally discuss the specific applications of microcalorimetry in studying various solid-liquid binding processes. There remains a vast expanse of thermodynamic information regarding solid-liquid interactions that await exploration via calorimetry.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

The pharmaceutical industry usually utilizes either hydrophobic or hydrophilic substances extracted from raw plant materials for preparing a final product, However, the plant material waste still contain substances with an opposite solubility. The aim of this study was to enhance the comprehensive usability of plant materials by developing a new non-wasting extraction method for eucalypt leaves and by investigating the phytochemical and pharmacological properties of eucalypt extracts and their 3D-printed dosage forms. The present extraction method enabled to prepare both hydrophobic soft extracts and hydrophilic (aqueous) dry extracts. We identified total 28 terpenes in the hydrophobic soft extract. In the hydrophilic dry extract, total 57 substances were identified, and 26 of them were successfully isolated. The eucalypt extracts studied showed a significant antimicrobial activity against Staphylococcus aureus, Pseudomonas aeruginosa, Bacillus subtilis, Candida albicans, Corynebacterium diphtheriae gravis, and Corynebacterium diphtheriae mitis. The anti-inflammatory activity of the dry extract was studied with a formalin oedema model in mice. The maximum anti-exudative effect of the dry extract was 61.5% at a dose of 20 mg/kg. The composite gels of polyethylene oxide and eucalypt extract were developed, and the key process parameters for semi-solid extrusion (SSE) 3D printing of such gels were verified. The SSE 3D-printed preparations of novel synergistically acting eucalypt extracts could have uses in antimicrobial and anti-inflammatory medicinal applications.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

Oscillons, fundamental to various physical domains, are examined in-depth in this paper. From Josephson junctions in superconducting circuits to classical and quantum field theories, oscillators reveal profound insights into diverse phenomena. The study primarily focuses on oscillons, distinctive field configurations with enduring localization, establishing intriguing connections with well-known models like the Sine-Gordon breather. Surprising parallels in the weak coupling limit illuminate the rich dynamics of oscillators. A semi-classical quantization method, discretizing the field into spatially homogeneous regions, exposes stability angles, providing insights into the quantum nature of oscillons. The application of this quantization framework to specific cases, including the Sine-Gordon breather, showcases its versatility. The results offer a comprehensive perspective on the quantization of oscillons, unraveling the intricate interplay between classical and quantum dynamics. In conclusion, this paper provides a profound exploration of quantum oscillators, unveiling novel connections and presenting a rigorous quantization framework. The gained insights contribute significantly to the broader understanding of oscillatory systems and their pivotal role in diverse physical phenomena.

From their discovery in 2002, BRAF mutations have been identified as clear drivers of oncogenesis in several cancer types. Currently, their incidence rate is nearly 7% of all solid tumors with BRAF V600E constituting approximately 90% of these diagnoses [1]. In melanoma, thyroid cancer, and histiocytic neoplasms, BRAF hotspot mutations are found at a rate of about 50%, while in lung and colorectal cancers they range from 3 to 10% of reported cases [2-5]. Though present in other malignancies such as breast and ovarian cancers, they constitute a small portion of diagnoses (<1%). Given their frequency along with advancements in screening technologies, various methods are used for the detection of BRAF-mutant cancers. Among these are targeted next-generation sequencing (NGS) on tumor tissue or circulating tumor DNA (ctDNA) and immunohistochemistry (IHC)-based assays. With advancements in detection technologies, several approaches have been taken for the treatment of BRAF mutant cancers. In this review we retrace the milestones that led to the clinical development of targeted therapies currently available for these tumors.

A significantly reduced stress concentration effect and a stable deformation behavior are exhibited by the arc-like S-shaped auxetic structure. Analytical works beyond the bar and hinge method to capture structural effects, such as bending, shearing, etc., in the S-structure are scarce in the literature. The deformation pattern of the S-structure is dominated by bending and shearing within the linear elastic region. In this work, Timoshenko beam theory is used to derive closed-form expressions for overall elastic modulus and Poisson’s ratio. This agrees well with the results of finite element simulations. An adjusted R-square value of over 0.99 and almost 0.82 is obtained for elastic modulus and Poisson’s ratio, respectively. From parametric studies, it’s established that under quasi-static transverse load, strut thickness and the angle `α’ are the most important parameters for controlling elastic modulus, specific energy absorption, negative Poisson’s ratio (NPR) effect, and relative density of the entire auxetic structure. Also, it’s found that energy absorption and elastic modulus increase together. Interestingly, the elastic modulus of the structure under transverse load lies in the range from 3 MPa to 250 MPa, which means this structure is compliant enough and can be used in cushioning, packaging, soft robotics applications, etc.

The binary metal oxide mesoporous interfacial layers (bi-MO meso IF layer) templated by a graft copolymer is synthesized between a fluorine-doped tin oxide (FTO) substrate and nanocrystalline TiO2 (nc-TiO2). Amphiphilic graft copolymers, Poly(epichlorohydrin)-graft-poly(styrene), PECH-g-PS, was used as a structure-directing agent, and the fabricated bi-MO meso IF layer exhibits good interconnectivity and high porosity. Even if the amount of ZnO in bi-MO meso IF layer increased, it was confirmed that the morphology and porosity of bi-MO meso IF layer was well maintained. In addtion, bi-MO meso IF layer coated onto FTO substrates show higher transmittance compared with a pristine FTO substrate and dense-TiO2/FTO, due to the reduced surface roughness of FTO. The overall conversion efficiency (η) of a solid state photovoltaic cells, dye-sensitized solar cell (DSSC) fabricated with nc-TiO2 layer/bi-MO meso IF layer TZ1 used as a photoanode reaches 5.0% at 100 mW cm-2, which is higher than that of DSSC with a nc-TiO2 layer/dense-TiO2 layer (4.2%), resulting from enhanced light harvesting, good interconnectivity, and reduced interfacial resistance. The cell efficiency of the device did not change after 15 days, indicating that the bi-MO meso IF layer with solid-state electrolyte has improved electrode/electrolyte interface and electrochemical stability. Additionally, commercial scattering layer/nc-TiO2 layer/bi-MO meso IF layer TZ1 photoanode fabricated solid state photovoltaic cells (DSSC) achieved an overall conversion efficiency (η) of 6.4% at 100 mW cm-2.

The purpose of this study is to assess the solid waste management status and practice in Sendafa town, Oromia regional state residents. In order to achieve this goal, the researcher intends to employ both primary and secondary data from the Sendafa town municipality. With the aid of multi-cluster sampling and a purposive sampling method, the researchers chose a sample size of 398 people and 10 interview responders. To utilize a systematic sampling technique at intervals of residences, individual samples were chosen. Quantitative data was cleaned and analysed using STATA software. A multiple linear regression model and logistic regression other descriptive statistics methods were then used to change the results. The qualitative data were imported, coded, and thematised using ATLAS.ti.9 in order to prepare respondents' interviews for analysis. The findings indicate that residents' poor solid waste management practices are a result of a lack of awareness, low family income transportation issues, issues with waste collectors, a lack of a sense of responsibility and belonging, and a failure to enforce current solid waste management laws. Solid waste accumulates near roads, bridges, and residential areas that are close to landfills, contaminating the area and leading to diseases like TB and Asthma (and other related health issues in children and adults who live there). Thus, researcher recommends that to have sustainable solid waste management the town administrators should have plan to develop awareness creation symposium or panel of discussion, resolve transportation issues, monitor and guide the routine activities of waste collectors, develop sense of belongingness for themselves and for the community, develop integrated solid waste land fill projects and working with all stakeholders like NGO and health institution will minimize the adverse effect of improper solid waste management. Keywords: Solid Waste, Status of Solid Waste Management, Land fill site suitability

This paper provides a first-time ever unification of information theory, semi-group theory with the theory of uncertain reasoning, through functional perspective. Fundamentally, the threshold theorems for the inference functional were devised. Furthermore, numerical experiments are illustrated. The complex proofs in our paper are original results which emphasizes the credibility of the class of Rényi Generalized Entropies as measures of information, and that the field is open to extend an enhanced methodology regarding queuing networks with heavy tails.

Chipman contends, in stark contrast to the conventional view, that utility is not a real number but a vector and is inherently lexicographic in nature. According to these views, it will be proved that, for every preordered topological space (X,≾,t), the assumption t to be finer than the order topology t≾ on (X,t), i.e. t⊇t≾, and the assumption the quotient topology t∣∼≾ that is defined on the preordered set (X∣∼,≾∣∼) of indifference classes of ≾ to be Hausdorff imply that a cardinal number κ and a (complete) preorder ≲ on {0,1}κ that is coarser than the lexicographical ordering ≤lex on {0,1}κ, i.e. ≤lex⊂≲, can be chosen in such a way that there exists a continuous order-embedding ϑ:(X,≾,t)⟶({0,1}κ,≲,t≤lex). This theorem will be compared with a theorem that, in particular, describes necessary and sufficient conditions for ≾ to have a continuous multi-utility representation.

Hong Kong is the biggest consumer of eggs in the world and ranks on the top with an average consumption of 24.52kg/capita/year. The egg consumption trend in Hong Kong has been increasing specifically; a drastic increase of about 100% has been observed from 2008 to 2020. One of the reasons behind this significant increase is the increase in the gross national income of Hong Kong in addition to the population growth rate. However, there was a slight decline in egg consumption trend in the year 2020 amid the COVID-19 pandemic. It has been estimated that there was a bulk of 17,100 tons of recoverable waste eggshells in 2019 (pre-COVID-19 situation), having a daily yield of 47 tons per day. Based on the linear regression, it may be expected that if the pre-COVID-19 trend of egg consumption remains sustained, there will be a big bulk of more than 45,000 tons per year and up to 125 tons per day of waste eggshells till 2050. In addition, a public survey was conducted across the city targeting individuals, families, and restaurants majorly on egg consumption and reuse. The survey outcomes revealed that Chinese eggs have an extensive market in Hong Kong, and people have a positive attitude towards eggshell recycling. Also, a massive population disposes of the waste eggshells while only a trace population reuses them. Therefore, Hong Kong has a very high potential to improve the circular economy by reusing waste eggshells on a commercial level in cementitious products.

A facile and environmentally benign method for a single-phase barium titanate synthesis in water vapor medium was studied to reveal the mechanism of phase transformation of the initial simple oxides mixture and estimate the capability of the product to be used as a raw material for low-frequency dielectric ceramics. The composition and structure of the reaction mixture treated in vapor at 130…150 °C as well as 230 °C for various time were investigated by means of XRD, SEM, HRTEM, EDX, and FTIR methods. The kinetics of the occurring phase transformation was described by Johnson-Mehl-Avrami-Erofeev equation. The reaction between the initial oxides was considered as a topochemical process with an apparent activation energy of 74…80 kJ mol^-1. A crucial role in this process belonged to the water vapor medium, which facilitated the generation of the reaction zone and its spreading inward the solid particles. The synthesized tetragonal barium titanate powder (mean particle size of 135 ± 24 nm) was sintered by a conventional technique at 1250 °C to obtain ceramics with grains of about 2 μm. Capacitance measurements performed a dielectric constant and loss tangent of ceramics, which reached 3879 and 6.7 10^-3, respectively, at 1 kHz and room temperature.

With continued scaling of semiconductor devices , the value of predictive analysis through 1 accurate quantum transport modeling is exponentially increasing. Quantum transmitting Boundary 2 method (QTBM) has been a well-known method of choice to model quantum transport in simple 1-D 3 devices. Here, we present an extension of the QTBM to the 2-D domain and apply it for more realistic 4 devices for accurate performance analysis.

The lactic acid bacteria Streptococcus thermophilus and Lactobacillus helveticus are commonly used as starter cultures in dairy product production. This study aimed to investigate the characteristics of fermented milk using different ratios of these strains and analyze the changes in volatile compounds during fermentation and storage. The 10:1 ratio of Streptococcus thermophilus CICC 6063 to Lactobacillus helveticus CICC 6064 showed optimal fermentation time (4.2 h), viable cell count (9.64 log10 colony-forming units/mL), and sensory evaluation score (79.1 points). In total, 56 volatile compounds were identified and quantified by solid-phase microextraction and gas chromatography–mass spectrometry (SPME-GC-MS), including aldehydes, ketones, acids, alcohols, esters, and others. Among these, acetaldehyde, 2,3-butanedione, 2,3-pentanedione, 2-heptanone, acetoin, and 1-heptanol had the highest odor activity values and contributed to the characteristic flavor of fermented milk. The concentrations and types of key flavor compounds reached their peak at the end of fermentation. Throughout the fermentation and storage process, the levels of 2,3-pentanedione and acetoin exhibited synergistic dynamics. These findings enhance our understanding of the chemical and molecular characteristics of milk fermented with Streptococcus thermophilus and Lactobacillus helveticus, providing a basis for improving the flavor and odor of dairy products during fermentation and storage.

Artificial intelligence (AI) has found extensive applications in the sustainability domain. The municipal solid waste incineration (MSWI) process can achieve waste-to-energy (WTE) goals through the assistance of automation and information technologies. In theory, AI can facilitate the intelligent operation of the MSWI process, simultaneously achieving low pollution emissions and high production efficiency. This study provides an overview of AI applications in the MSWI process. Addressing fundamental challenges, the optimal control of the MSWI process is categorized into four aspects: modeling, control, optimization, and maintenance. Subsequently, this study conducts a detailed analysis and discussion of AI applications in each of these technological domains. In conclusion, this paper outlines the future research directions and provides an outlook on the fundamental issues pertaining to AI applications in the optimal control of the MSWI process.

Stipa tenacissima (S. tenacissima), or esparto, is a perennial tussock grass that coexists with Pinus halepensis (P. halepensis) in semi-arid mediterranean woodlands. This research was carried out to explore diurnal transpiration at leaf level in esparto grass under different levels of pine-esparto competition and in contrasting environmental conditions of soil water. The measurements were spanned from the summer 2020 to spring 2021. The relationship between transpiration and competence was conducted in open and closed P. halepensis stands and taken into account the type of leave (green, senescent) and the maturity of the esparto grass. We observed a higher control of transpiration in green leaves, and correlations between transpiration and soil water were noted exclusively in this type of leaf. Our results substantiated a significant impact of pine competitors on transpiration of esparto grass, particularly during seasons characterized by high water-demand scenarios: the summer drought period and the commencement of the growing and flowering period (spring). Furthermore, our findings confirmed a greater response to transpiration in mature bushes compared to young ones under severe water stress, denoting higher adaptation to drought as esparto ages. Our results may have important implications for the dynamics and management of these semi-arid mixed woodlands, as well as the planning of reforestation programs aimed at restoring esparto grass steppes.

In order to achieve its carbon peak and neutrality targets, a high proportion of distributed power sources are connected to the distribution network in China, which greatly increases the risk of distribution network operation. Aiming at the above problems, this paper proposes an active distribution network risk planning model based on multi-source data from carbon capture and power internet of things, and conducts exceeding testing of distribution network based on the stochastic load flow algorithm with semi-invariant and level expansion, calculates the semi-invariant of each order of node state vectors and branch current vectors, and then utilizes the Gram-Charlier level expansion to obtain the exceeding probability density function and probability distribution function of the node voltages and line powers of the distribution network. The probability density function and probability distribution function of the exceeding are obtained using the Gram-Charlier series expansion. Combined with multi-source data, the active distribution network with integrated energy system considering carbon capture is modeled. According to the risk scenario of the distribution network, the nonconvex constraints in the model are simplified by the second-order cone relaxation, and the optimal planning scheme of the distribution network is solved by combining the gurobi solver with the risk index as the first-level objective and the economic benefit as the second-level objective. The simulation results of a coupled network consisting of a 39-node distribution network and an 11-node transportation network verify the effectiveness of the proposed model.

Repeated single-point measurements of thoracic bioimpedance at single (low)-frequency are strongly related to fluid changes during hemodialysis. Extension to semi-continuous measurements may provide longitudinal details in the time pattern of the bioimpedance signal, and multifrequency measurements may add in-depth information on the distribution between intra- and extracellular fluid. This study aims to investigate the feasibility of semi-continuous multifrequency thoracic bioimpedance measurements by a wearable device in hemodialysis patients. Therefore, thoracic bioimpedance was recorded semi-continuously (i.e. every ten minutes) at nine frequencies (8 – 160 kHz) in 68 patients during two consecutive hemodialysis sessions, complemented by a single-point measurement at home in-between both sessions. On average, the resistance signals increased during both hemodialysis sessions and decreased during the interdialytic interval. The increase during dialysis was larger at 8 kHz (∆ 32.6 Ω during session 1 and ∆ 10 Ω during session 2) compared to 160 kHz (∆ 29.5 Ω during session 1 and ∆ 5.1 Ω during session 2). Whereas the resistance at 8 kHz showed a linear time pattern, the evolution of the resistance at 160 kHz was significantly different [p < 0.0001]. Measuring bioimpedance semi-continuously and with a multifrequency current is a major step forward in the understanding of fluid dynamics in hemodialysis patients. This study paves the road towards remote fluid monitoring.

: Protease-producing yeasts were isolated from potato wastes and screened for protease production on skim milk agar plates The best producer of protease isolate was identified as Clavispora lusitaniae. The strain showed better enzyme production using tomato pomace and bread waste mix as a solid fermentation substrate. The optimized conditions improved enzyme activity and showed a maximal production of 33450±503 IU/g compared with the initial activity of 11205,78 ±360 without medium optimization. A threefold increase in protease activity after medium optimization proved the reliability of using the PBD and CCD design. A 19.76-fold purified enzyme and a yield of 32.94% were obtained after purification. The protease showed maximum activity at pH 4 and 60 °C and was resistant to Tween 20, Tween 40, SDS, and β-mercaptoethanol, Ca2+, and Mg2+ stimulated it. The protease activity was strongly inhibited in the presence of urea, and EDTA. The results revealed Clavispora lusitaniae protease's ability to degrade wheat seeds and flour gluten by 98.7% and 97% respectively under pH 4 for 24 hours at 40 °C. According to this study, this enzyme could be a potential candidate for the food industry, particularly for treating wheat seed and flour to reduce the immunogenicity of gluten.

The primary goal of this review is to provide a comprehensive overview of the state-of-the-art in solid-state batteries (SSBs), with a focus on recent advancements in solid electrolytes and anodes. The paper begins with a background on the evolution from liquid electrolyte lithium-ion batteries to advanced SSBs, highlighting their enhanced safety and energy density. It addresses the increasing demand for efficient, safe energy storage in applications like electric vehicles and portable electronics. A major part of the paper analyzes solid electrolytes, key to SSB technology. It classifies solid electrolytes as polymer-based, oxide-based, and sulfide-based, discussing their distinct properties and application suitability. The review also covers advancements in anode materials for SSBs, exploring materials like lithium metal, silicon, and intermetallic compounds, focusing on their capacity, durability, and compatibility with solid electrolytes. It addresses challenges in integrating these anode materials, like interface stability and lithium dendrite growth. This review includes a discussion on the latest analytical techniques, experimental studies, and computational models to understand and improve the anode-solid electrolyte interface. These are crucial for tackling interfacial resistance and ensuring SSBs' long-term stability and efficiency. Concluding, the paper suggests future research and development directions, highlighting SSBs' potential in revolutionizing energy storage technologies. This review serves as a vital resource for academics, researchers, and industry professionals in advanced battery technology development. It offers a detailed overview of materials and technologies shaping SSBs' future, providing insights into current challenges and potential solutions in this rapidly evolving field.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Immunohistochemistry is a powerful technique, widely used in biomedical research and clinics, that allows to determine the expression levels of some proteins of interest in tissue samples by means of the intensity of color due to the expression of biomarkers using specific antibodies. As such, immunohistochemical images are complex and problematic to be quantified. Recently we proposed a novel method including a first separation stage based on nonnegative matrix factorization (NMF) that achieved good results. However, that method was highly dependent on sparseness and non-negativity parameter choice and on algorithm initialization. Furthermore, the previously proposed method needed a reference image as starting point for the NMF algorithm. In the present work, we propose a new, simpler and robust method for the automated unsupervised scoring of immunohistochemical images based on bright field. Our work is focused on images from tumor tissues marked with blue (nuclei) and brown (protein of interest). The new proposed method represents a simpler approach that, in one side, avoids the use of NMF for the separation stage, and in the other side, circumvents the need for a control image. This new approach determines the subspace spanned by the two colors of interest by means of principal component analysis (PCA) with dimension reduction. This subspace is a two-dimensional space, allowing the finding of color vectors by considering the peaks of density of points. The method also develops a new scoring stage by avoiding, again, reference images, making the procedure more robust and less dependent on the parameters. Experiments for the semi-quantitative scoring of images in five categories exhibit promising and consistent results when compared to manual scoring carried out by experts.

Contacting bodies in extreme environments are prone to severe wear and failure due to friction and seizure, which are associated with significant thermal and mechanical loads. This phenomenon greatly impacts the economy since most essential components encounter these challenges during machining, an unavoidable step in most manufacturing processes. In machining, stress can reach 4 GPa, and temperatures can exceed 1000 °C at the cutting zone. Severe seizure and friction are the primary causes of tool and workpiece failures. Liquid lubricants are popular in machining for combatting heat and friction; however, concerns about their environmental impact are growing, as two-thirds of the 40 million tons used annually are discarded and they produce other environmental and safety issues. Despite their overall efficacy, these lubricants also have limitations, including ineffectiveness in reducing seizure at the tool/chip interface and susceptibility to degradation at high temperatures. There is therefore a push towards solid lubricants, which promise a reduced environmental footprint, better friction management, and improved machining outcomes but also face challenges under extreme machining conditions. This research aims to provide a thorough insight into solid lubricant use in machining, discussing their mechanisms, effectiveness, constraints, and potential to boost productivity and environmental sustainability.

Solid-state transformer (SST) is a promising technology for smart grids due to its flexible power control (better reliability) and high efficacy (by decreasing losses) compared with traditional transformers. The SST is designed in tandem with three stages, i.e., the input, isolation, and output stages. As three converter stages are used to design the SST to make a more reliable device in practice, it is highly prone to instabilities. Moreover, the key objective of SST design is to implement a modern power distribution system to make it more intelligent and reliable. The stability issue can be even more complicated by the presence of distributed energy resources in the distribution system. Thus, the stability of SST must be measured prior to /during the design, and to determine, a state-space model is used, which is developed in this paper. Each stage of SST is modeled with its controller, and the system's stability is measured through the controllability and observability test. Further, the conversion from state-space to transfer function model is done, and the stability of SST is shown using frequency and time-domain diagrams. With these, the different plots, namely, the Bode plot, Nyquist plot, Nichols chart, Root locus, pole-zero plot, and Eigen plot, are used to ascertain the relative and absolute stability. Finally, the SST Simulink model is tested and validated through hardwate-in-the-loop simulation, i.e., OPALRT, to show its effectiveness and applicability.

Control over the composition of III-V ternary nanowires grown by the vapor-liquid-solid (VLS) method is essential for bandgap engineering in such nanomaterials and fabrication of functional nanowire heterostructures for a variety of applications. From the fundamental viewpoint, III-V ternary nanowires based on group V intermix (InSbxAs1-x, InPxAs1-x, GaPxAs1-x and many others) present the most difficult case, because the concentrations of highly volatile group V atoms in a catalyst droplet are beyond the detection limit of any characterization technique and therefore principally unknown. Here, we present a model for the vapor-solid distribution of such nanowires, which fully circumvents the uncertainties that remained in the theory so far, and link the nanowire composition to the well-controlled parameters of vapor. The unknown concentrations of group V atoms in the droplet do not enter the distribution, despite of the fact that a growing solid is surrounded by the liquid phase. The model fits quite well the available data on the vapor-solid distributions of VLS InSbxAs1-x, InPxAs1-x and GaPxAs1-x nanowires grown with different catalyst. Even more importantly, it provides a basis for the compositional control of III-V ternary nanowires based on group V intermix, and can be extended over other material systems where two highly volatile elements enter a ternary solid alloy through a liquid phase.

The poor solvent crystallization of carbapenem CS-023 has been performed at 25 °C. The following results have been obtained: 1) A solvate crystal Form A (5/2 Ethanol·1/2 H2O) is recovered from 80 v/v% ethanol solution, 2) Form A transforms to Form H (4H2O) by the solid-phase transition through the solvate-free polymorph, Form A-2, and Form A also transformed to Form C (1Ethanol·3H2O) by the solvent-mediated transformation. In the present study, we found that Form C also transforms to Form H by the solid-phase transition through the solvate-free polymorph, Form C-2. The three polymorphs, Form A, H, and C, were composed of the helical-chain structures, respectively. However, there was an incomprehensible affair in the solid phase transition among the three polymorphs. Namely, Form A comprised a left-handed helix.On the other hand, Form C and Form H’s helix chains were in a left- and right-handed helix complex. The solid-phase transition of Form A into Form H suggested the switch of helicity in the solid. We attempted to explain the helicity change in the solid phase transition. As a result, it was suggested that the over-absorption of water of Form A-2 at high humidity plays a vital role in the helicity change.

Knowledge about the genesis and evolution of black soils in the Eastern Mediterranean is vital for sustainable land management. In this study, the black soils that currently occur in the Eastern Mediterranean were analyzed in different bioclimatic zones and were found to genetically be long to three soil types: 1-Calcareous black soils (Rendzina, Para-Rendzina) (Rendzic or Somerirendzic Leptosols -Typic Rendolls or Lithic Rendolls), 2-Hydromorphic black soils (Calcic Chernozems -Haploxerolls). 3- Black soils on Basalt (Somerirendzic Leptosols) (Haploxerolls). The impact of the relief was obvious on both the thickness of the solum and the mollic horizon. Rendzina occurs on the toe and feet slope, Para-Rendzina on the shoulders, and Chernozems on a flat plain. The color of the epipedon in Rendzina reflects the origin of the prevailing parent material from which they are derived: Proper Rendzina found on limestone, chalk, sandstone, conglomerate, and claystone; Reddish Rendzina on Dolomite and hard limestone, and Grayish Rendzina on Serpentine. It was also found that the Hydromorphic black soils only occur on calcic marl and lacustrine deposits in the depressions arising from the Dead Sea faults under saturation or bad drainage conditions. This soil has a thick, dark mollic horizon and high organic matter content.

Nano-drugs and nano-delivery systems are rapidly evolving, with new strategies emerging in the current practices. The evolution of these technologies began with modifying the chemical structure, progressing to supramolecular ionic complexes, and culminating in elegant ad hoc delivery systems. Nanoparticles have numerous benefits as a carrier system for delivering therapeutic agents to intra-arterial sites. These benefits include their subcellular size, targeted surfaces, good suspensibility, and uniform dispersity, making them an ideal choice for catheter-based delivery. Despite the advancements made in the field of nano-drugs and nano-delivery systems, there are still some hurdles to overcome in terms of their commercial availability.The current review presents an updated summary of recent advancements in nano-drugs and nano-delivery systems, including their commercial availability. We aim to discuss the present challenges and prospects of commercially available nano-drugs and nano-delivery systems. Here, we provide a precise and informative overview of the current state of these technologies and underscore the potential they hold for future developments. Further, we have categorized commercially available modifications, name, parent company and their main applications in nano-drugs.

Real and complex analytic functions are largely studied in the field of complex analysis and are seen as very useful tools in solving problems in mathematics, physics and engineering. Real and complex numbers are a subset of semi-structured complex numbers (a new number set created to algebraically solve division by zero). Nevertheless, the properties of analytic functions made up of semi-structured complex variables (called semi-structured complex analytic functions) is yet to be explored. This limits the range of possible problems that can be resolved using analytic functions). In this regard, the aim of this paper was to expound upon the properties of semi-structured complex analytic functions and show their application in solving engineering problems. The results of this paper included (1) developing a full set of Cauchy–Riemann Equations for the semi-structured complex -space; (2) define sufficient and necessary conditions for a semi-structured complex function to be analytic; (3) determine the relationship between semi-structured complex analytic functions, Laplace’s Equations and Poisson’s Equations; and (5) provide an example of the use of these functions.

Peptide/Histidine Transporter PHT1 (SLC15A4) is expressed in lysosomal membranes of immune cells where it plays an important role in metabolic and inflammatory signaling. PHT1 is an H+-coupled/histidine symporter that can transport a broad range of oligopeptides, including a variety of bacterial-derived peptides. Moreover, it enables the scaffolding of various metabolic signaling molecules and interacts with key regulatory elements of the immune response. Therefore, it is not surprising that PHT1 is associated with the development of autoimmune diseases, such as systemic lupus erythematosus (SLE). Unfortunately, the pharmacological development of PHT1 has been hampered by the lack of appropriate transport assays. With the aim to address this shortcoming, a novel transport assay based on solid supported membrane-based electrophysiology (SSME) is presented. Key findings of the present SSME studies include the first recordings of electrophysiological properties, a pH dependence analysis, an assessment of PHT1 substrate selectivity, as well as the transport kinetics of the identified substrates. In contrast to previous works, PHT1 is studied its native lysosomal environment. Moreover, observed substrate selectivity is validated by molecular docking. Overall, this new SSME-based assay is expected to contribute to unlock the pharmacological potential of PHT1 and to deepen the understanding of its functional properties.

Cross-industry clusters are important for the economic prosperity of a region. However, studies are lacking to address competitive clusters among the aviation and tourism industries. Thus, this paper considers the case of both industries in terms of clusters and synergies formed. This research aim is to provide an understanding of both industries' protagonists' involvement in contributing to knowledge insights on the establishment of synergies or clusters among the two industries. Cyprus is highly dependent on tourism and aviation because they facilitate connectivity. The research is filled with semi-structured interviews with the main players and organizations of the airline and tourism industries (government bodies, airports, airlines, tour operators, and hotels). The results are indicative and suggest that, in a small geographical context, the notion of clusters involves a synergetic relationship among tourism stakeholders. Airlines’ role is important because it has an effect on all stakeholders involved in tourism.

The asymmetric synthesis of polyunsaturated triene C18:3 n-3 and C18:3 n-6 methoxylated ether lipids (MEL) of the 1-O-alkyl-sn-glycerol type is described as possible structural candidates for a triene C18:3 MEL of an unknown identity found in a mixture of shark and dogfish liver oil. Their C18:3 hydrocarbon chains constitute an all-cis methylene skipped n-3 or n-6 triene framework, along with a methoxyl group at the 2'-position and R-configuration of the resulting stereogenic centre. The methoxylated polyenes are attached by an ether linkage to the pro-S hydroxymethyl group of the glycerol backbone. The syntheses were based on the polyacetylene approach that involves a semi-hydrogenation of the resulting triynes. Both syntheses were started from our previously described enantio- and diastereomerically pure isopropylidene-protected glyceryl glycidyl ether, a double-C3 building block that was designed as a head group synthon for synthesis of various types of MELs.

Sodium-phosphate-based glass-ceramics (GCs) are promising materials for a wide range of applications, including solid-state sodium-ion batteries, microelectronic packaging substrates, and humidity sensors. This study investigates the impact of 24-hour heat-treatments at varying temperatures on Na-Ge-P glass, with a focus on (micro)structural, electrical, and dielectric properties of prepared GCs. Various techniques such as powder X-ray diffraction (PXRD), infrared spectroscopy-attenuated total reflection (IR-ATR), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) are employed. With the elevation of heat-treatment temperature, crystallinity progressively rises; at 450 °C, the microstructure retains amorphous traits featuring nanometric grains, whereas at 550 °C, heat-treatment results in fully crystallized structures characterized by square-shaped micron-scale grains of NaPO3. The insight into the evaluation of electrical and dielectric properties is provided by Solid-State Impedance Spectroscopy (SS-IS), revealing a strong correlation with the conditions of controlled crystallization and observed (micro)structure. The glass-ceramic heat-treated at 450 °C achieves the highest DC conductivity of 2.30×10–8 Ω–1 cm–1 at 393 K. As the heat-treatment temperature rises, the crystallization of the NaPO3 phase depletes the glass matrix of mobile Na+ ions, resulting in a reduction in DC conductivity. Dielectric parameters also decrease with rising heat-treatment temperature, with the glass-ceramic heat-treated at 550 °C displaying the lowest permittivity of 19.37 and the dielectric loss of 0.008. This research uncovers the intricate relationship between heat-treatment conditions and material properties, emphasizing that controlled crystallization allows for precise modifications to microstructure and phase composition within remaining glassy phase, ultimately facilitating fine-tuning of material properties.

This study focuses on the synthesis, characterization and study of a new perovskite-type materials as cathode in SOFC. The synthesized doped perovskites have been successfully synthesized with high purity. The electrochemical performance of these materials was extensively examined through the characterization of I-V-P and EIS curves at the three temperatures: 750, 800 and 850 °C. Where it is revealing a substantial reduction of total resistances by approximately 50% and 70%, accom-panied by an impressive increase in power densities by around 200% and 300%, respectively. The cell featuring Sm0.01Sr0.99Fe0.5Co0.5O3 exhibited the most commendable electrochemical properties at each temperature, following closely were Pr0.01Sr0.99Fe0.5Co0.5O3 and La0.01Sr0.99Fe0.5Co0.5O3.

Background: The liver has emerged as a frequent transplanted organ which can transmit T. gondii between seropositive donors and seronegative recipients. Associated with the immunosuppressive therapy of recipients, the presence of cysts in donor livers elevate the risk of severe toxoplasmosis in recipients. Objectives: The objective of the study was to verify the frequencies of positive serology in liver graft donors and their respective recipients, as well as to verify whether their clinical signs presented post-transplant are associated with the serological status of recipients. Patients and methods: All data on liver transplant recipients from 2008 to 2018 were obtained from the MVPeP electronic medical records of the Liver Transplant Service of FUNFARME/FAMERP. IgM and IgG anti-T. gondii antibody serology was investigated by chemiluminescence. According to the serological profile, four groups of recipients were assessed (G1: IgG-/IgM-; G2: IgG+/IgM-; G3: IgG+/IgM+, G4: IgG-/IgM+). Results: The numbers of recipients according to the serological profile groups were: G1: 20 (41.7%), G2: 26 (54.1%; G3: 2 (4.2%). No cases were found for G4. Post-transplant clinical manifestations such as fever without defined cause, lung nodules, headache, hepatosplenomegaly, encephalopathy and hepatitis (A, B and C) were reported in all groups. Conclusions: This study demonstrates that there is a high prevalence of T. gondii infection in liver recipients and, therefore, screening should be intensified. Furthermore, a high incidence of co-infection with hepatitis A was identified especially in patients who died in the post-transplant period.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

The main issue in this work is to study limit functions necessary for the reliability assessment of the structural steel with the use of the relative entropy apparatus. This would be done using a few different mathematical theories relevant to this relative entropy, namely those proposed by Bhattacharyya, Kullback-Leibler, Jeffreys, and Hellinger. Probabilistic analysis in the presence of uncertainty in material characteristics would be delivered using three different numerical strategies – Monte-Carlo simulation, stochastic perturbation method as well as the semi-analytical approach. All these methods are based on the Weighted Least Squares Method approximations of the structural response functions versus the given uncertainty source and they would allow efficient determination of the first two probabilistic moments of the structural responses including stresses, displacements, and strains. The entire computational implementation would be delivered using the Finite Element Method system ABAQUS and computer algebra program MAPLE, where relative entropies, as well as polynomial response functions, would be determined. This study would demonstrate that the relative entropies may be efficiently used in reliability assessment close to the widely engaged First Order Reliability Method (FORM).

Sr4Al6O12SO4 samples were obtained from the compound mixture formed by a solid–state reaction of Al2O3, SrSO4, and SrCO3. Samples were compacted at 100MPa to form pellets of 1 and 4cm in diameter and were sintered at 1400°C for 4 hours. The compound was analyzed by X–ray diffraction. Static immersion and wettability tests were performed to evaluate corrosion resistance in contact with Al–Si. Corrosion tests were carried out by immersion at 800, 900, and 1000°C for 24, 50, and 100 hours, while wettability was carried out at 900, 1000, and 1100°C for 2 hours. Subsequently, the samples were prepared metallographically. Samples were analyzed by optical microscopy, scanning electron microscopy, and image analysis. In general, reaction products consisting of alumina, spinel, oxides, and sulfates were found. The contact angles obtained were 124° to 135°. It is concluded that ceramic substrate Sr4Al6O12SO4 is resistant to corrosion by Al–Si alloy, since the slight thickness of the reaction products found in the samples (100μm) considering the severe conditions of the experiment: 1000°C and 100 hours of isothermal temperature. Furthermore, it can be said that Sr4Al6O12SO4 is not wettable by Al–Si alloys.

Gelephu, located in the Himalayan region, has experienced one of the strongest development activities due to the suitable topography and geographic location, which has led to rapid urbanization. The main objective of the study is to perform land use land cover (LULC) mapping for Gelephu for 2016 and 2023 by a Random Forest (RF) classifier, using the Semi-automatic Classification Plugin (SCP) in QGIS and identify LULC changes. Furthermore, the study assessed the vegetation change dynamics within the study area by analysing the Normalized Difference Vegetation Index (NDVI) for 2016 and 2023. Additionally, the study characterized the resulting LULC change for Gelephu Thromde, a sub-administrative municipal entity, as a result of the notable intensity of the infrastructure development activities. The current study used a framework to collect Sentiniel-2 satellite data, which was then used for pre- and post-processing to create LULC and NDVI maps. The classification model achieved high accuracy, with an area under the curve (AUC) of up to 0.89. The corresponding LULC and NDVI statistics were analysed to determine the current status of the LULC and vegetation indices, respectively. The LULC change analysis reveals urban growth of 5.65% and 15.05% for Gelephu and Gelephu Thromde, respectively. The NDVI assessment shows significant deterioration in vegetation health with a 75.11% loss of healthy vegetation in Gelephu between 2016 and 2023. This research provides the first version of LULC and NDVI maps of Gelephu. The analysis results indicate possible future implications on sustainable development management in Gelephu Bhutan.

Flexible energy storage devices, such as solid-state supercapacitors, are becoming increasingly attractive due to their characteristics of high electrochemical performance, reliability, light weight, flexibility, absence of electrolyte leakage, high power density, and long lifetime. For the optimization of the solid-state symmetrical supercapacitor proposed in this work, it was employed in sodium and lithium form Aquivion electrolyte membrane, which serves as the separator and electrolyte. As electrode materials, carbon xerogels, synthesized by microwave-assisted sol-gel methodology, with designed and controlled properties were obtained. Commercial activated carbon (YP-50F, 'Kuraray Europe' GmbH) was used for comparison. Specifically, the developed solid-state symmetrical supercapacitors deliver sufficient high specific capacitances of 105−110 F g−1 at 0.2 A g−1, along with an energy density of 4.5 Wh kg−1 at 300 W kg−1, and in a voltage window of 0-1.2 V in an aqueous environments, also demonstrating excellent cycling stability up to 10,000 charge/discharge cycles. These results can demonstrate the potential applications of carbon xerogel as an active electrode material and cation exchange membrane as the electrolyte in the development of solid-state supercapacitor devices

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

It remains unclear in the literature what is the cause of the so-called alkali-carbonate reaction (ACR) damage to concrete yet, a consensus is reached when considering dedolimitization as non-expansive. However, expansion and cracks as distress features are often attributed to alkali-silica reaction (ASR) when evidence of a reactive mineral is found in the aggregate. Evidently, different types of aggregates may produce different types and degrees of damage. Therefore, this work aims to assess the damage to concrete generated and propagated by the so-called ACR susceptible reactive Kingston coarse aggregate through mechanical testing (i.e., direct shear test), microscopy (the damage rating index – DRI), and other techniques. Distinct induced expansion levels (i.e., 0%, 0.05%, 0.12%, and 0.20%) were selected to compare the distress caused by ACR to concrete affected by ASR. Result show that the behaviour of ACR, namely as captured through the DRI, is inconsistent with that of ASR thus attesting to ACR being a distinct distress mechanism.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

Lithium-ion batteries with improved energy densities have made understanding the Solid Electrolyte Interphase (SEI) generation mechanisms that cause mechanical, thermal, and chemical failures more complicated. SEI processes reduce battery capacity and power. Thus, a review of this area's understanding is important. It is essential to know how batteries degrade in EVs to estimate battery lifespan as it goes, predict, and minimize losses, and determine the ideal time for a replacement. Lithium-ion batteries used in EVs mainly suffer two types of degradation: calendar degradation and cycling degradation. Despite the existence of several existing works in the literature, several aspects of battery degradation remain unclear or have not been analyzed in detail. This work presents a systematic review of existing works in the literature. The results of the present investigation provide insight into the complex relationships among various factors affecting battery degradation mechanisms. Specifically, this systematic review examined the effects of time, side reactions, temperature fluctuations, high charge/discharge rates, depth of discharge, mechanical stress, thermal stress, and the voltage relationship on battery performance and longevity. The results revealed that these factors interact in complex ways to influence the degradation mechanisms of batteries. For example, high charge currents and deep discharges were found to accelerate degradation, while low temperatures and moderate discharge depths were shown to be beneficial for battery longevity. Additionally, the results showed that the relationship between cell voltage and State-of-Charge (SOC) plays a critical role in determining the rate of degradation. Overall, these findings have important implications for the design and operation of battery systems, as they highlight the need to carefully manage a range of factors to maximize battery performance and longevity. The result is an analysis of the main articles published in this field in recent years. This work aims to present new knowledge about fault detection, diagnosis, and management of lithium-ion batteries based on battery degradation concepts. The new knowledge is presented and discussed in a structured and comprehensive way.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

Text annotation is an essential element of the natural language processing approaches. The manual annotation process performed by humans has several drawbacks, such as subjectivity, slowness, fatigue, and possibly carelessness. In addition, annotators may annotate ambiguous data. So, we developed the concept of automated annotation to get the best annotations using several machine-learning approaches. The proposed approach is based on an ensemble algorithm of meta-learners and meta-vectorizer techniques. The approach employs a semi-supervised learning technique for automated annotation, aimed at detecting hate speech. This involves leveraging various machine learning algorithms, including Support Vector Machine (SVM), Decision Tree (DT), K-Nearest Neighbors (KNN), and Naive Bayes (NB), in conjunction with Word2Vec and TF-IDF text extraction methods. The annotation process is performed using 13,169 Indonesian YouTube comments data. The proposed model used a Stemming approach using data from Sastrawi and also new data of 2,245 words. Semi-supervised learning uses 5%, 10%, and 20% of labeled data as compared to performing labeling based on 80% of the datasets. In semi-supervised learning, the model learns from the labeled data, which provides explicit information, and the unlabeled data, which offers implicit insights. This hybrid approach enables the model to generalize and make informed predictions even when limited labeled data is available, ultimately enhancing its ability to handle real-world scenarios with scarce annotated information. In addition, the proposed method uses a variety of thresholds for matching words labeled with hate speech ranging from 0.6, 0.7, 0.8, and 0.9. The experiment showed that the KNN-Word2ec model has the best accuracy value of 96.9% with a scenario of 5%:80%:0.9. However, several other methods have also accuracy above 90%, such as SVM and DT based on both text extraction methods in several test scenarios.

This article aims at investigating the complex relationship between the local population and its natural and urban environment. The study of area which, is previously dominated by cereal cultivation, facing profitability challenges due to climate change, water scarcity Rapid urban expansion and overexploitation of aquifers, influenced by changes in agricultural practices, are disrupting the local ecosystem. The study relies on three interconnected indicators: population growth, climate change effects on agriculture, and the NDVI (Normalized Difference Vegetation Index) reveal the impact of these factors on agricultural practices. Google Earth Engine was employed to determine urbanization and greenness indices using scripts. Key findings include a shift towards intensive and protected agriculture, driven by individual and collective choices of official and unofficial actors, deviating from government directives. Additionally, the study highlights the unsustainability of this new agricultural direction, as the available water re-sources cannot meet the demands, potentially leading to recurrent agricultural shortages. The study underscores the importance of incorporating agricultural production into future urban planning and development programs to maintain a renewed balance between built environ-ments and agriculture on the outskirts of cities.

Drought is a powerful natural hazard that has significant effects on ecosystems amid the constant threats posed by climate change. This study investigates agricultural drought in a semi-arid Mediterranean basin through the interconnections of four indices: precipitation (meteorological reanalysis), vegetation development, thermal stress, and soil water deficit (remote sensing observations). The study focuses on the determination of agricultural drought periods. Firstly, the temporal connections between the various indices at different spatial scales and in different parts of the basin are investigated. Thereafter, a modified run-theory approach based on normality and dryness thresholds is applied. The Pearson correlations at different spatial scales showed a medium to low level of agreement between the indices, which was explained by the geographical heterogeneity and the climatic variability between the agrosystems within the basin. It is also shown that the cascade of impacts expected from lower precipitations is revealed by the cross-correlation analysis. The connection between precipitation deficit and vegetation remains significant for at least one month for most pairs of indices, especially during drought events, suggesting that agricultural drought spells can be connected in time through the three or four selected indices. Short-, mid-, and long-term impacts of precipitation deficiencies on soil moisture, vegetation, and temperature were revealed. As expected, the more instantaneous variables of soil moisture and surface temperature showed no lag with precipitation. Vegetation anomalies at the monthly time step showed a two-month lag with a preceding effect of vegetation to precipitation. Finally, the determination of drought events and stages with varying thresholds on the run-theory showed the large variability of duration, magnitude, and intensity according to the choice of both normality and dryness thresholds.

Droughts are a common occurrence in various climates and are primarily caused by a prolonged decrease in rainfall. Several factors contribute to droughts, including temperature, wind speed, relative humidity, rainfall timing, amount, and intensity during the growing season. The objective of this study is to establish a new index, named soil moisture and evapotranspiration revealed drought index (SERDI), for displaying dry and wet conditions based on combining both soil moisture and evapotranspiration (Penman-Monteith) to improve drought early warning and its severity globally. For validation of the SERDI with other indices such as LST, VHI, NDVI, and NDWI, different ways used such as R-square, RMSE, MAPE, and P-value to estimate the accuracy, variability of data, the forecast conditions, and how the significance of data. The results showed that the low RMSE and high r² were found between SERDI with LST and VHI. In contrast, the low R- square and high RMSE were between SERDI with NDVI and NDWI in most of the semi-arid areas. Furthermore, most of the semi-arid areas from Iran, Iraq, Syria, Jordan, and Israel experienced moderate and severe dry conditions, except some parts of these regions had normal conditions in Iran and Syria. The SERDI analysis revealed a strong correlation between (LST) and a moderate correlation with (VHI) across all study areas. However, the relationship between other indices, like (NDWI) and (NDVI), varied depending on the regions. To conclude, SERDI can be used globally for detecting drought based on soil moisture and evapotranspiration.

A single-crystal of ytterbium-doped “mixed” yttrium-lutetium aluminium garnet with a stoichiometric composition of (Y0.601Lu0.233Yb0.166)3Al5O12 was grown by the Czochralski method and its structure, vibronic, spectroscopic and laser properties were studied. The stimulated-emission cross-section for Yb3+ ions was maximized to 2.53×10-20 cm2 at 1031 nm, the emission bandwidth is ~8 nm and the reabsorption-free luminescence lifetime of the 2F5/2 state is 1.063 ms. Pumped at 941 nm, the Yb-laser generated a maximum output power of 1.04 W at 1.03 and 1.05 μm with a high slope efficiency of 76.4% and a laser threshold of 76 mW. A continuous wavelength tuning over a range of 51.6 nm (1026.4 - 1078.0 nm) was also achieved. Power scaling is achieved using a 969 nm-diode pumped microchip cavity. A maximum output power of ~9 W is obtained at 1.05 μm with a slope efficiency of 76% and with an almost circular laser beam profile.

As the global community shifts away from fossil fuels towards more environmentally friendly energy alternatives, there is an escalating demand for sophisticated energy storage solutions. Solid-State Batteries (SSBs) have emerged as a promising advancement, presenting a superior substitute to conventional lithium-ion batteries. This review provides an in-depth examination of SSBs, emphasizing their enhanced energy density, safety, and longevity. We evaluate conventional cathode materials, including lithium cobalt oxide (LiCoO2), lithium manganese oxide (LiMn2O4), and lithium iron phosphate (LiFePO4). Additionally, we introduce emerging materials such as sulfides, oxides, and air-based cathodes, discussing their benefits, limitations, and their congruence with solid electrolytes. Special attention is devoted to the structural fine-tuning of cathode ma-terials, investigating approaches like nanostructuring, surface coatings, and composite strategies to counteract issues such as restricted conductivity and structural volatility. The review critically analyzes the electrical and thermal properties of these materials, which are essential for battery safety and efficacy. Moreover, we present a comparative assessment of cathode materials based on performance indicators and identify prevailing research voids and hurdles in the commerciali-zation of SSB cathodes. Concluding, we suggest prospective research directions and innovations, underscoring the revolutionary potential of SSB technologies in paving the way for a sustainable energy horizon.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

In recent years, the use of solid waste fillers to partially replace natural fillers in asphalt mixtures to produce high-performance asphalt mixtures has received widespread attention. However, differences in the material properties of solid waste fillers remain a problem for this recycling method. To address this issue, limestone powder in asphalt mixtures was replaced by three solid waste fillers (steel slag powder, tailings powder and calcium carbide slag powder) in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, AC and SMA asphalt mixtures were designed and produced and characterized for wet stability. The results showed that asphalt mixtures with solid waste fillers were superior to LP asphalt mixtures in terms of resistance to water damage, and steel slag powder showed the best improvement in moisture stability of asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. In addition, the moisture stability of asphalt mixture with limestone filler was significantly improved with the addition of anti-stripping agents. In contrast, the moisture stability of asphalt mixtures with solid waste filler was slightly improved. Solid waste fillers could be used in asphalt mixtures and have a similar function as the anti-stripping agent. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added, recycling option.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

In this paper we report on the use of an in-house developed solid-state hybrid microwave and radiofrequency generator operating at frequencies of 2.45 GHz and/or 480 kHz for cancer ablation in various tissues. The generator has demonstrated increased accuracy due to its custom-designed hardware, which incorporates the latest technologies and algorithms to control the emitted power versus temperature profile of the treated sample. In particular, the hybrid generator incorporates control systems based on impedance or reflected power measurements that allow controlled ablation without causing unwanted carbonisation and without including areas where tissue damage is not desired. Tests performed ex-vivo on chicken breast and bovine liver show that radiofrequency ablation (RFA) is very effective for performing controlled ablations with minimally invasive probes, such as cardiac pathologies, small lesions, tissues with particular composition, while microwave ablation (MWA) is optimal for performing large ablations in highly vascularised tissues, such as liver cancer, where it is necessary to achieve higher temperatures.

Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.

Multibeam echo-sounders provide ideal data for semi-automated seabed feature extraction and accurate morphometric measurements. However, these methods have not been tested in morphologically highly complex environments. In this study, bathymetric and raw backscatter data were initially used to manually map the complex reef morphology found in the semi-enclosed Gera Gulf, in the northern Aegean Sea (Greece). A large number of reefs (more than 7000) were detected, making manual mapping extremely time-consuming. Benthic Terrain Modeller (BTM) was selected as a semi-automated method to map the reefs. The BTM did not function properly in this irregular relief and the results were discouraging. Trying to improve the BTM functionality, both bathymetry and slope were modified (enhanced); this time, the BTM outcome was unexpectedly improved, producing accurate results that appeared to exceed the accuracy of manual mapping. To compare the final maps with the distribution of the reefs, mapcurves were created to estimate the Goodness-of-Fit (GOF), while Precision, Recall, and F1 Score were also calculated. GOF values suggest more than 50% overlap between the resulting polygons while, Precision, Recall and F1 score resulted in values higher than 0.78 suggesting good detection accuracy for the semi-automated method. It becomes apparent that BTM provided more efficient results in comparison to the time-consuming manual mapping. This study asserts that semi-automated mapping stands as an effective method for delineating the geomorphometry of intricate relief and serves as a powerful tool for habitat mapping and decision-making.

Personal Information Management Systems (PIMS) are acquiring a prominent role in the data economy by promoting services that help individuals to have more control over the processing of their personal data, in line with the European data protection law. One of the highlighted solutions in this area is Solid, a new protocol that is decentralizing the storage of data, through the usage of interoperable Web standards and semantic vocabularies, to empower its users to have more control over the processing of data by agents and applications. However, to fulfill this vision and gather widespread adoption, Solid needs to be aligned with the law governing the processing of personal data in Europe, the main piece of legislation being the General Data Protection Regulation (GDPR). To assist with this process, we analyze the current efforts to introduce a policy layer in the Solid ecosystem, in particular, related to the challenge of obtaining consent for processing personal data, focusing on the GDPR. Furthermore, we investigate if, in the context of using personal data for biomedical research, consent can be expressed in advance, discuss the conditions for valid consent and how it can be obtained in this decentralized setting, namely through the matching of privacy preferences, set by the user, with requests for data and whether this can signify informed consent. Finally, we discuss the technical challenges of an implementation that caters to the previously-identified legal requirements.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

Environmental perception is a powerful tool for identifying community needs and potential within their surroundings. This study assessed tourists' environmental perception regarding solid waste and its impact on the Hurtado balneary, located in Valledupar, Colombia. From May to July 2023, the investigation delved into the environmental attitudes and behaviors of 769 balneary users by employing a combination of observation, photographic documentation, and a comprehensive 21-question online survey. The findings unveiled compelling insights: an overwhelming 98.8% of participants acknowledged the adverse effects of solid waste on the environment, with an impressive 98% demonstrating a willingness to participate in waste management efforts. Alarmingly, 42.13% exhibited limited awareness of waste management practices, reflecting a lack of public interest and commitment (41.61%). Statistically significant disparities emerged: 59% of waste items were not appropriately disposed of in designated receptacles. Reasons for this included a lack of a sense of belonging (50.2%) and inadequate environmental education (45.6%). 96% expressed the need for river conservation signage, while 59.8% had not engaged in environmental training. The implications of these results extend beyond the Hurtado balneary, potentially informing solid waste management strategies in other aquatic environments. Furthermore, this investigation aligns with three critical Sustainable Development Goals: SDG 12, emphasizing responsible consumption and production; SDG 13, addressing climate action; and SDG 15, advocating for life on land and below water. Keywords: Tourism; solid waste; surface water; environmental management.

Recently, a paper was written to establish semi-structured complex numbers ℍ (a new number set invented to enable division by zero) as a useful mathematical tool providing novel results from its application in engineering and science. Whilst the paper was a milestone, the application of this number set to quantum and classical physics had not been fully explored. Consequently, the aim of this research was to use semi-structured complex numbers to develop a new mathematical model for the mass of an object and in course unite classical and quantum physics in a simple yet effective manner. As its major contributions this paper: (1) develops a new mathematical model for the mass of an object called the wave-mass function using De Broglie’s mass and frequency relation and semi-structured complex numbers; (2) uses the new wave-mass function to determine what happens to an object traveling at the speed of light; (3) derives a relation between Schrödinger’s wave function and the new wave-mass function; (4) derives a relation between Einstein’s Field Equation and the new wave-mass function; (5) uses the wave-mass function to combine Einstein’s Field Equation with Schrödinger’s wave function to form a new quantum gravity equation. These results and their applications provide a firm foundation to advance the number set ℍ as a useful mathematical tool.

This article presents the results of studies of the structure and conductive properties of Na3Fe2(PO4)3 polycrystals synthesized by solid-phase and melt (using concentrated optical radiation) methods. It has been established that with the melt method, the synthesis of the material occurs under significantly nonequilibrium temperature-gradient conditions, which leads to the creation of deformations in the sample that contribute to an increase in ionic conductivity. The ability of the Na3Fe2(PO4)3 structure to adapt to anomalous deformations that occur under temperature-gradient conditions indicates the elasticity of the crystalline framework {[Fe2(PO4)]3-}3∞. Through a comparative assessment of the structural parameters and conductive properties of these materials, it is shown that polycrystals obtained by the melt method have a better texture and greater ionic conductivity. The advantage of this method is that the duration of the synthesis of α-Na3Fe2(PO4)3 is halved. It is concluded that this method is applicable to obtain effective polycrystals of other compositions.

An inorganic solid electrolyte is the most favorable candidate for replacing flammable liquid electrolytes in lithium batteries. Lithium Lanthanum Zirconium Oxide (LLZO) is considered as a promising solid electrolyte due to its safe operating potential window (0-5V) combined with its good electrochemical stability. In this work, 250 g batches of pre-sintered Tadoped (Li7La3Zr1.6Ta0.4O12, TaLLZO) were synthesized for bulk production of dense LLZO electrolyte. A simple two-step thermal treatment process was developed. The first thermal step at 950 °C initiates nucleation of LLZO carefully controlling process parameters such as heating atmosphere, temperature and dopant concentration. In the second thermal step at 1150 °C, sintered discs were obtained as solid electrolytes, with relative densities of 96%. X-ray diffraction analysis confirmed the phase purity of the sintered TaLLZO disc, and refined data was used to calculate the lattice parameter (12.944 Å). Furthermore, the presence of the Ta dopant in the disc was confirmed through X-ray photoelectron spectroscopy (XPS) analysis. The ionic and electronic conductivity values of TaLLZO disc were 104 S cm-1 and 10-10 S cm-1, respectively. These values confirm that the prepared (Ta-LLZO) discs exhibit ionic conductivity while being electronically insulating, being suitable for use as solid electrolytes with the requisite electrical properties.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x &lt; 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K &lt; 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.