In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

There is little doubt that the efficacy of MnDPDP and its therapeutic improved counterpart Ca4Mn(DPDP)5 mainly depends on their MnSOD-mimetic activity when it comes to their potential use as rescue medicines, during e.g., acute myocardial infarction. However, pharmacokinetic considerations suggest that the efficacy of MnDPDP on Pt2+-associated neurotoxicity depends on another action of this drug. Electron Paramagnetic Resonance (EPR) studies have demonstrated that Pt2+ outcompetes Mn2+ and endogenous Zn2+ from binding to fodipir (DPDP), and hence suggest that the previously reported CIPN protective efficacy of MnDPDP is a result of chelation and elimination of Pt2+ by DPDP, which in turn suggests that Mn2+ is unnecessary for efficacy when it comes to oxaliplatin-associated CIPN.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

There is currently much interest in avoiding precious metals in Catalysis. The devel-opment of nickel catalysts to replace palladium in the Mizoroki-Heck reaction is a relevant case in this line of research since both elements share many chemical features. This contri-bution focuses on -Phenyl elimination in alkylnickel complexes. This is the microscopic reverse of olefin insertion (or carbometallation), a fundamental step of the Heck cycle that is usually considered irreversible and selectivity-determining. However, the potential reversibil-ity of carbometallation is generally concealed by the facile beta-hydrogen elimination that follows. Where -hydrogen elimination is hindered, beta-aryl elimination may ensue. We have previously shown that cationic 2-methyl-2-phenylpropyl (neophyl) palladium com-plexes supported by bidentate ligands experience -Ph elimination, which can be seen as an example of olefin de-insertion. In this contribution, we report that -phenyl elimination can also occur in their nickel analogs, in which case fast hydrolyses of the resulting phenyl product can follow the reaction. We investigated the mechanism of these processes and compared their feasibility for nickel and palladium catalysts using DFT calculations. These results are relevant information for the design of nickel-based catalysts for the Heck reac-tion.

This study examined the accumulations and transfer of manganese into 11 wild plants from the mining soils of Gümüşköy, Turkey. The greatest silver resource in Turkey is found in the Gümüsköy mining area, which is situated roughly 25 kilometers to the west of Kütahya. ICP-MS was used to determine the Mn contents in soil and plant samples that were taken from the field. In the research area, the average Mn concentrations in the soil, roots, and shoots of wild plants were 1872, 1076, and 1048 ppm, respectively. Based on their ECS and ECR values, the plants were divided into three groups: the best plants, good plants, and candidate plants. While Glaucium flavum, Carduus nutans, Phlomis sp., Onosma sp., and Verbascum thapsus were selected as the best plants, Cynoglossum officinale, Anchusa arvensis were determined as good plants, and the others (Alyssum saxatile, Centaurea cyanus, Silene compacta, Isatis were determined as candidate plants. According to the current study, all of the best and good plants in the study region had a very high ability to remove Mn. As a result, these plants can be helpful in studies involving phytoremediation or remediation of Mn-polluted soil.

In order to study the feasibility of copper-nickel smelting slag（CNSS） and palygorskite for large-scale consumption and utilization in the field of mine filling, gellable composite materials were prepared from copper-nickel smelting slag ,cement and palygorskite. The effects of palygorskite addition and curing time on the mechanical properties and microstructure of copper-nickel smelting slag-based cementitious materials were studied in detail. The results showed that the addition of palygorskite had a positive effect on the curing of the cemented filler of the non-ferrous smelting slag by promoting the early hydration reaction. palygorskite also affected the mechanical properties of the cementitious materials with different maintenance times and the ability to cure heavy metals. The strength of gellable composite materials reaches 23.05MPa when 1% palygorskite, 50% of copper-nickel smelting slag and 48% cement were used, which meet the standards requirements of filling materials for mine goaf. The addition of 1% palygorskite can improve the ability of cementitious materials to solidify heavy metals to realize the economic utilization of solid waste in mining areas.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

The study reports the effect of some metal carbides (niobium carbide, vanadium carbide, titanium carbide, and manganese sulfide) on hydrogen embrittlement in the pipeline industry using plane wave’s density functional theory (DFT). Our results predicted that the interaction of hydrogen molecules with these metals carbide occurs in the long range with binding energy varying in the energy window [0.70eV to 0.043eV]. Also, our study shows the desorption of H2 molecules from these metal carbides in the chemisorptions. Since, hydrogen embrittlement, occurs in the atomic state of hydrogen, therefore our finding in the atomic interaction of hydrogen with NbC, VC, TiC, and MnS showed that the strength of the trapping of the hydrogen atom could be classified as: TiC+H>VC+H>NbC+H> MnS+H. In addition, our study reveals that the carbon site is the most favorable hydrogen trapping site than the metal one. Furthermore, our results demonstrate that increasing the layer can also be an efficient way to enhance the trapping capacity.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

The objective of this work is the study the crystal structure and elemental content of braunite-hematite and braunite-psilomelane oxide manganese ores y means of X-ray diffractometry (XRD), Energy Dispersion X-ray (EDX) analysis, and X-Ray fluorescent (XRF) analysis. It was found that heat treatments at 600, 800, and 1000 °C promote the phase transitions of the manganese ores to the formation of thermostable phases hausmannite and bixbyite without change in the metallic composition. The homogeneity of the structure increases with increasing temperature, which is expressed in the decreasing of the Mn content in the EDX spectra after sintering above 800 °C as well as in a decrease of the phase number to only two phases: bixbyite and quartz. Remarkably, the hausmannite phase is obtained in the fraction of 61% after sintering the braunite-hematite ore sample at 1000 °C for 4 h. Since hausmannite is widely used to produce building materials, electrodes, catalysts, and other materials, these results are promising for developing technologies for obtaining new products based on phases of manganese minerals at high temperatures.

The removal of sulfur from fossil fuels is one of the most important processes in modern refineries. It is accomplished via hydrodesulfurization (HDS) of the sulfur organic compounds in presence of heterogeneous catalysts. In the current work, heterogeneous catalysts containing cobalt and mo-lybdenum supported on mesoporous materials type SBA-15 and AlSBA-15 were synthesized for application in the HDS reactions of thiophene in n-heptane stream. The mesoporous materials were synthesized by hydrothermal method starting from TEOS, pseudobohemite, hydrochloric ac-id and water. Pluronic P123 was used as template. The best calcination conditions for removal of the organic template were optimized by thermogravimetry analysis (TG/DTG). The calcined SBA-15 and AlSBA-15 supports were submitted to co-impregnation with solutions of cobalt nitrate and ammonium heptamolybdate, aiming the production of 15% in mass of metal loading with atomic ratio of [Co/(Co+Mo)]=0.45. The obtained materials were dried and calcined for obtaining the mesoporous catalysts in the form of CoMo/SBA-15 and CoMo/AlSBA-15. The catalysts were char-acterized by XRD, TG/DTG, SEM and nitrogen adsorption. From XRD analysis, it was verified that after decomposition of the cobalt and molybdenun salts, were formed MoO3, Co3O4 and Co-MoO4 oxides on the supports, being attributed to these chemical species the activity for the HDS reactions. The activity of the obtained catalysts was evaluated in a continuously flowing tubular fixed-bed microreactor coupled on-line to a gas chromatograph, using n-heptane stream contain-ing 12070 ppm of thiophene (ca. 5100 ppm of sulfur) as a model compound. From the catalytic tests it was verified that the synthesized catalysts presented good activity for the reaction, and the main obtained products were cis- and trans-2-butene, 1-butene, n-butane and low amounts of iso-butane. The presence of 1,3-butadiene and tetrahydrothiophene (THT) were not detected. A mechanism of the primary and secondary reactions and subsequent formation of the olefins and paraffins, in the CoMo/SBA-15 and CoMo/AlSBA-15 mesoporous catalysts were proposed, con-sidering steps of desulfurization, hydrogenation, dehydrogenation, THT decyclization and isomerization.

Hydroxyapatite (HAP) is the main mineral component of bones and teeth. It is widely used in medicine as a bone filler and coating for implants to promote new bone growth. Ion substitutions into the HAP structure highly affect its properties. One of the important substituents is manganese. This paper presents the new results obtained by high-precision density functional theory calculations using hybrid functionals, for studies of the Mn/Ca substitutions in HAP in a wide manganese concentration range within 2x2x2 supercell model. The experimental data on the mechanochemical synthesis of HAP-Mn samples with different Mn concentrations are also presented. The comparison between experiment and theory showed good agreement: the HAP-Mg unit cell parameters and volume decrease with increasing degree of Mn/Ca substitution. It is shown that electronic energy levels appear inside the band gap Eg of HAP, which depend on the concentration of Mn and change the photo-excitation energy of HAP, making its effective value Eg* less than the band gap Eg, and generally changing the photoelectronic properties of HAP. It was established that the energies of formation of the substitutions Mn/Ca depend on the position of the Ca atom (Ca1 or Ca2) and on the concentration of manganese. It has been shown that the replacement of calcium cations with manganese occurs predominantly at the Ca2 position.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

In this work, we have studied microstructure and unusual ferromagnetic behavior in cobalt (Co)-implanted epitaxial tin dioxide (SnO2) films. The study was aimed to provide a comprehensive understanding of the interplay between cobalt implant distribution, crystal defects, such as oxygen vacancies, and magnetic properties in Co-implanted SnO2 films, which has potential applications in spintronics and memristor devices. The scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometry (VSM), differential thermo-magnetic analysis (DTMA), and ferromagnetic resonance (FMR) were employed for investigations of SnO2 films implanted with 40 keV Co+ ions at room or the elevated temperatures of substrate. The experimental data showed that the Co ion implantation with high fluence of 1.0 1017 ions/cm2 induces significant changes in the microstructure of SnO2 films, leading to the appearance of ferromagnetism with the Curie temperature significantly above room temperature. Strong influence of implantation temperature and subsequent high-temperature annealing in air or in vacuum on magnetic properties of Co-implanted SnO2 films were established. Moreover, the chemical effect of ethanol on FMR spectra were observed. The obtained results are discussed within the model of two magnetic layers with different concentration and valence states of the implanted cobalt and with high content of oxygen vacancies.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

Chromium-nickel austenitic stainless steels are widely used due to their high corrosion resistance, good weldability and deformability. To some extent, their application is limited by their mechanical characteristics. As a result of their austenitic structure, increasing the static and dynamic strength of the components can be achieved by surface cold work. Due to the tendency of these steels to undergo intercrystalline corrosion, another approach to improve their mechanical characteristics is the use of low-temperature thermo-chemical diffusion processes. This article proposes a new combined process based on sequentially applied diamond burnishing (DB) and low-temperature gas nitriding (LTGN) to optimally improve the fatigue strength of 304 steel. The essence of the proposed approach is to combine the advantages of the two processes (DB and LTGN) to create a zone of residual compressive stresses in the surface and subsurface layers–the enormous surface residual stresses (axial and hoop) introduced by LTGN, with the significant depth of the compressive zone characteristic of static surface cold working processes. DB (both smoothing and single-pass hardening), in combination with LTGN, achieves a fatigue limit of 600 MPa, an improvement of 36.4% compared to untreated specimens. Individually, smoothing DB, single-pass DB and LTGN achieve 540 MPa, 580 MPa and 580 MPa, respectively. It was found that as the degree of plastic deformation of the surface layer introduced by DB increases, the content of the S-phase in the nitrogen-rich layer formed by LTGN decreases, with resultant increased content of -phase, and a new (also hard) phase: stabilized nitrogen-bearing martensite.

When wastewater containing methylene blue, a cationic dye is improperly treated or immediately dumped into the environment, it can degrade the quality of water bodies and contaminate the ecological environment. The removal of methylene blue from the aqueous solution is critical and urgent. The present work focuses on the use of maize stalk agricultural waste to prepare an adsorbent for the removal of cationic dye (methylene blue) from an aqueous solution. The prepared maize stalk biochar (MSB) was modified with MnO2 and the modified maize stalk biochar was characterized using Fourier transform infrared (FTIR) spectroscopy. Taguchi technique was employed to determine the optimum conditions for the removal of methylene blue (MB) dye from aqueous solution by MMSB. The factors were adsorbent dose (0.5, 1.0 and 1.5 g/100 mL), initial dye concentration (100, 200 and 300 mg/L), contact time (30, 60, 90 minutes) and pH (4, 6 and 8). Among the investigated process factors, adsorption efficiency was influenced by adsorbent dose and initial MB dye concentration. The optimum parameters were 1 g/100 mL adsorbent dose, 100 mg/L initial dye concentration, 60 minutes contact time and a pH of 8.0. This yielded a removal efficiency of 87.49% with adsorption capacity of 206.53 mg/g. The adsorption kinetics agreed with the pseudo-second-order (R2 of 0.999968) model and fitted a Langmuir isotherm (R2 of 0.9795) representing homogeneous monolayer chemisorption.

High levels of groundwater containing both arsenic and fluorine are prevalent, resulting in serious health problems when consumed as drinking water. This co-pollution phenomenon is widespread and requires urgent attention. The multiple forms of arsenic and arsenic-fluorine co-contamination pose a significant challenge to efficiently co-remove both substances. This research utilized a green and stable synthesis approach to create MgLaFe LDO heterostructures, which were anchored on α-MnO2 nanowires. The materials comprise magnesium and lanthanum elements with a powerful attraction towards fluoride ions, elemental iron, which can establish stable compounds with arsenate, and MnO2, which can effectively oxidize arsenous acid, thereby enabling efficient co-removal of arsenic and fluorine. The efficient oxidation process of the MnO2 nanowire and the prompt ion adsorption process of the LDO work together synergistically. The adsorption performance was assessed through isotherm and kinetic fitting. Chemisorption was found to be the process for As(Ⅲ), As(V), and F- adsorption, with As(Ⅲ) going through monolayer adsorption on the surface of MnO2 nanowires, while As(V) and F- were mainly adsorbed by multilayer process on LDO. The maximum adsorption capacities were 111.76 mg/g, 230.51 mg/g, and 765.10 mg/g for As(Ⅲ), As(V), and F-, respectively. The XPS analysis provided further elucidation on the adsorption mechanism of the MnO2@LDO heterostructure, detailing each component's role in the process. The results confirm the successful construction of the heterostructure and its efficient coupling of oxidation and adsorption.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

Cobalt-doped alumina catalysts were prepared by different methods, applying either the conventional wet impregnation (WI) and/or the advanced spray impregnation (SI), and evaluated as novel oxidation catalysts for CO and MeOH oxidation. The spray impregnation technique aims towards the synthesis of core-shell catalytic nanostructures to secure chemical/thermal stability of the active sites on the catalyst carrier. The catalysts were further promoted with low Pd content (0.5 wt.%) applying either incipient wetness impregnation (DI) or spray impregnation. The results revealed the superior performance of spray impregnated catalysts (Co/γ-Al2O3-SI) for both reactions. The deposition of Co oxide on the outer surface of the alumina particle (SEM images) and the availability of the active Co phase, resulted in the enhancement of Co/γ-Al2O3 catalysts oxidation activity. Pd incorporation increased catalysts reducibility (TPR-H2) and improved the catalysts performance for both reactions. However, Pd incorporation method affected the catalytic performance; as with the SI method the active phase of Co3O4 was probably covered from PdO and was not available for the oxidation reactions. On the contrary, the incorporation of Pd with the DI method resulted in better dispersion of PdO all over the Co/Al catalyst surface, maintaining available Co active sites and better Pd-Co interaction. MeOH desorption studies revealed the methanol oxidation mechanism; Co/Al catalysts promote partial oxidation of MeOH to formaldehyde (HCHO) and dehydration to dimethyl ether (DME), while Pd-based Co/Al catalysts enhance the complete oxidation of methanol to CO2 and H2O.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

This manuscript presents the result of utilizing cellulose as a template to prepare na-nosized WO3-NiWO4 and its application as co-catalysts in Pt/WO3-C and Pt/WO3-NiWO4-C for ethanol and glycerol electro-oxidation. Microcrystalline cellulose was hydrolyzed with phosphotungstic acid (H3PW12O40) to prepare the nanosized template of crystalline cellulose. Next, the template was impregnated with Ni(NO3)2, rendering a precursor mate-rial that is subsequently air-calcinated, removing the carbon-template material to obtain the nanometric WO3 and NiWO4. Elemental analysis confirmed the coexistence of nickel and tungsten, whereas the thermal analysis evidenced the high thermal stability of these materials. The X-ray diffractograms displayed crystal facets of WO3 and, when added Ni, of NiWO4. The transmission electron micrographs corroborated the formation of na-nosized particles with average particle sizes close to 50 nm. Finally, to apply this material, Pt/WO3-C and Pt/WO3-NiWO4-C were prepared and used in ethanol and glycerol electro-oxidation in alkaline medium, observing a promotional effect of the oxide and tungstate by reducing the onset potential and increasing the current density. These materials show great potential to produce clean electricity or green hydrogen contributing to energetic transition.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

The paper presents the numerical and experimental results of research aimed at determining the influence of hardness in the range of 50-90 Shore A of layered tools made of elastomeric materials on the possibility of forming Inconel 625 nickel-based alloy sheets. A stamping die made of 90MnCrV8 steel (hardness 60HRC) was designed for forming embosses in drawpieces, ensuring various stress states on the cross-section of the formed element. The principle of operating the stamping die was based on the Guerin method. Finite element-based numerical modelling of the forming process for various configurations of polyurethane inserts was also carried out. The drawpieces obtained by sheet forming were subjected to geometry tests using optical 3D scanning. The results confirm that in the case of forming difficult-to-deform Inconel 625 Ni-based alloy sheets, the hardness of the polyurethane inserts significantly affects the geometric quality of the obtained drawpieces. The assumptions made in numerical simulations were verified in experimental studies. Based on the test results, it was concluded that the selection of polyurethane hardness should be determined by the shape of the formed element. Significant non-uniform sheet metal deformation was also found, which may pose a problem in the process of designing forming tools and technology of plastic forming of Inconel 625 Ni-based alloy sheets.

Plastics, primarily microplastics, are among the greatest pollutants in aquatic environments. Their removal and/or degradation in these environments are crucial to ensure an optimal future of the ecosystems. In this work MnO2 particles were synthesized and characterized for the removal polystyrene microplastics as a model. MnO2 catalyzes the peroxide reaction, resulting in the formation of oxygen bubbles that propel the pollutants to the surface, achieving removal efficiencies of up to 80%. To achieve this, hydrothermal synthesis was employed using various methods. Parameters such as MnO2, microplastics and H2O2 concentrations were varied to determine the optimal conditions for microplastics recovering. The ideal conditions for a low microplastic concentrations of microplastics (10 g L-1) are 0.2 g L-1 MnO2, 1.6% of H2O2 and 0.01 triton as a surfactant. In these conditions the micromotors can recover approximately of 80% 300 nm sized polystyrene microplastic within 40 min.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V-microalloying 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure was consisted of ferrite, RA and secondary martensite (SM) after subjected to SPA process. (V, Mo)C with disc-like morphology mainly precipitated during intercritial tempering, and the aspect ratio of particle decreased, leading to the appearance of near-spherical morphology. After subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: out layer of ferrite, interlayer of SM and inner layer RA) enabled high yield strength of 1097 MPa, total elongation of 14%, and impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated about 108 MPa.

OsNRAMP5—a member of the same family as the iron, manganese (Mn), and cadmium (Cd) transporter OsNRAMP1—is responsible for the transport of Mn and Cd from soil in rice. Knockout of OsNRAMP5 markedly reduces both Cd and Mn absorption; therefore, in low -Mn environments, such plants would exhibit Mn deficiency and suppressed growth. Amino acid mutations in IRT1 alter its metal selectivity. We generated random mutations in OsNRAMP5 via error-prone PCR, and used yeast to screen for the retention of Mn absorption and inhibition of Cd absorption. The results showed ththat alanine 512th is the most important amino acid residue for Cd absorption, and that its substitution resulted in the absorption of Mn but not Cd.

Bimetallic colloidal CoPt nanoalloys, with a very low platinum content, were successfully synthesized following a modified polyol approach. Powder X-ray diffraction, IR spectroscopy, thermogravimetric analysis, and Transmission Electron Microscopy studies were performed to estimate the crystal structure, morphology and surface functionalization of the colloids respectively, while the room temperature magnetic properties were measured using Vibrating Sample Magnetometer. The particles exhibit excellent uniformity, with a narrow size distribution, and display strong room temperature hysteretic ferromagnetic behavior even in the as-made form. Upon annealing at elevated temperatures, progressive formation and co-existence of exchange coupled both chemically ordered and disordered phases, significantly enhance the room temperature coercivity.

The usage of biotechnological molecules and processes is an indispensable part of the resource technology research. The development of novel biomolecules therefore needs to be adapted to the existing applicational conditions and biological processes are to be examined. Novel biosorbents may not only contribute to future applications but can be of further used, e.g. to better understand the interaction of known metal- and metalloid-interacting biological molecules and materials. This review highlights biotechnological approaches published so far for bioremediation as well as metal recovery with a special spotlight on cobalt, nickel and arsenic.

This study investigates the magnetization of Cobalt (Co) nanoparticles with two different crystal structures: a centered cubic (fcc) and an hexagonal close packed (hcp), under the magnetic field of the Earth. For that reason, the hysteresis loops of the two material samples are exported and compared with the corresponding value by experimental procedure in the laboratory under the Earth’s magnetization. For both samples, the nanoparticle number variation and the nearest neighbor distance effect, in the Co hysteresis loop are investigated, structural information that is useful for the sample preparation. For the simulations the Finite Element Method (FEM) was used, while experiments are conducted using a measurement set-up based on fluxgate magnetometers. From the simulation, it is proven that, for both samples, the nanoparticle number effect does not change the hysteresis loop. In contrast, when the distance between the nanoparticles increases, the magnetization obtains smaller value. This study aims to build a novel, simple and economical measurement arrangement enabling in situ magnetic measurements for ferromagnetic nano-material characterization. As the need for continuous knowledge of the condition and the phase of ferromagnetic nanoparticles that is crucial in many applications, like catalytic processes, this work aims to introduce an alternative approach that will add another dimension to conventional chemical reaction engineering this of the magnetic state of the material resolved in time and space and to contribute in the field of the monitoring and the early fault diagnosis of nanoparticle materials.

Nickel is widely used in industrial processes and plays a crucial role in many applications. However, most of the nickel resource mainly exists as nickel oxide in laterite nickel ore with complex composition, resulting in difficulty in upgrading the nickel content using physical separation methods. In this study, high-grade ferronickel concentrates were obtained through a carbothermal reduction and magnetic separation using laterite nickel ore and anthracite as raw materials. The effects of different types of additives (CaF2, Na2SO4 and H3BO3), carbon ratio (nc/no in metal oxides) and grinding time on the recoveries and grades of ferronickel concentrates were experimentally investigated, along with the microstructure and chemical composition of the products. CaF2 was proved to be the primary active additive in the aggregation and growth of the ferronickel particles, and the improvement of the grade of the product. Under the optimal conditions of CaF2 addition of 12 wt.%, carbon ratio of 1.4, and grinding time of 240 s, high-grade magnetically separable ferronickel concentrate with nickel grade 8.93 wt.% and iron grade 63.96 wt.% was successfully prepared. This work presents a practical method for the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore, contributing to the development of strategies for the sustainable extraction and utilization of nickel resources.

Nitric acid is a key component in the production of nitrate fertilisers and is industrially produced using the Ostwald process. The Ostwald process can be further intensified by oxidising nitric oxide to nitrogen dioxide using heterogeneous catalysts. We have explored various monometallic and bimetallic catalysts for NO to NO2 oxidation and found ruthenium supported on ceria, containing 10 wt.% manganese to be a promising catalyst for oxidising NO to NO2 at low temperatures at industrially relevant conditions. For a feed comprising 10% NO, 6% O2, 15% H2O and rest Ar, and 8% NO, 2% NO2 5% O2, 15% H2O and rest Ar, the ruthenium-manganese catalysts attained NO-NO2 equilibrium below 400∘C. For the 5wt.% ruthenium and 10 wt.% manganese on ceria catalyst, an apparent activation energy of 39.4 kJ/mol and 85.4 kJ/mol were observed in the absence and presence of NO2, respectively. These findings demonstrate the potential of supported bimetallic ruthenium-manganese catalysts for efficient oxidation of NO to NO2 at low temperatures which can lead to significant process intensification of nitric acid plants.

Gold nanoclusters (AuNCs) with fluorescence in the Near Infrared (NIR) by both one- and two-photon electronic excitation were incorporated in mesoporous silica nanoparticles (MSNs) using a novel one-pot synthesis procedure where the condensation polymerization of alkoxysilane monomers in the presence of the AuNCs and a surfactant produce hybrid MSNs of 49 nm diameter. This method was further developed to prepare 30 nm diameter nanocomposite particles with simultaneous NIR fluorescence and superparamagnetic properties, with a core composed of superparamagnetic manganese ferrite nanoparticles (MnFe2O4) coated with a thin silica layer, and a shell of mesoporous silica decorated with AuNCs. The nanocomposite particles feature NIR-photoluminescence with 0.6% quantum yield and large Stokes shift (290 nm), and superparamagnetic response at 300 K, with a saturation magnetization of 13.4 emu g-1. The conjugation of NIR photoluminescence and superparamagnetic properties in the biocompatible nanocomposite has high potential for application in multimodal bioimaging.

This study presents a combined electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) and Scanning Kelvin Probe Force Microscopy(SKPFM) investigation on the natural passivation process of stainless steels (AISI 316 and AISI 304) and nickel-based alloy (INCONEL 600) as a function of immersion time in an alkaline medium (pH = 13). EIS measurements show an increase in the resistance of the film with increasing immersion time in the electrolyte. After 3 days of immersion, for the three alloys, the films formed constitute an effective barrier to the dissolution of the alloys as shown by AFM and SKPFM. The oxide film growth on each substrates is only influenced by trenches formed during the polishing step and don’t depend on the chemical composition.

Metallic masters can be used as a metallic mold to replicate polymeric pieces with high resolution. Metallic masters with high resolution were created by photolithography technique and nickel electrodeposition technique. AZ 9260 photoresists and SPR 220-7.0 photoresists were used to coat metallic substrates and to compare results. Steel substrate and nickel substrate were used as the metallic substrate to compare results. Two different nickel electrodeposition protocols were used to compare results. In the conclusion section, was determined the best photoresist, metallic substrate, and nickel electrodeposition protocol to fabricate metallic masters.

Cobalt (Co) is a transition metal and is classified as a beneficial metal for plants, but its benefits for plants remain obscure. Cobalt has been reported to negatively affect plant physiochemical processes both at higher (toxic) and lower (deficient) applied levels. High concentrations of cobalt in plant organs cause irreversible changes to the plant cells, mainly via enhanced production of reactive radicals. Moreover, Co and its compound play an essential role in humans as they are the central atoms of cobalamin, a co-enzyme precursor whose absence causes anemia. Hence, the optimum Co supply to plants is critical for customary plant metabolic workings. Henceforth, monitoring Co behavior in the soil-plant-human system is highly imperative. This review highlighted the latest literature on (i) Co in soil and plants; (ii) its mobility and phyto-availability in soil; (iii) phytouptake and translocation towards shoot tissues; (iv) toxic and deficient effects of Co on plants; (v) plant detoxification mechanisms under increased Co levels inside plants; and (v) its role in the human body. For this purpose, 1026 plant observations from literature data were analyzed related to Co biogeochemical behavior in the soil-plant system. The data analysis revealed an overall increase in 567 observations and a decrease in 381 observations. However, these general trends in plant responses vary significantly for different types of plant species and physiological attributes. Overall, the current review delineates an updated and critical representation of the biogeochemical behavior of Co in the soil-plant-human system, supported by up-to-date 9 main tables, 14 supporting tables, and 3 figures. The authors believe that the literature presented here can be of great interest to scientists, researchers, policymakers, and graduate-level students.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

A comparative study of the physicochemical properties of natural bentonite clays of Pogodayevо (Republic of Kazakhstan, mod.1) and Dash-Salakhli (Republic of Azerbaijan, mod.2) deposits and modification of the bentonite clay with polyhydroxocations of iron (III) and aluminium (III). It-wasestablished that the modification of natural bentonitesusing polyhydroxocations of iron (III) and aluminium(III) by the method of "co-precipitation" leads to a change in their chemical composition, structural and sorption properties. The results showed that hydroxy-aluminum cations ([Al3O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe were intercalated into clay layers, which led to an increase in the values of d001 and specific surface areas compared to those of the original bentonite, from 37 to 120 for the Pogodaevo bentonite and from 51 to 172 respectively for bentonite from the Dash-Salakhli deposit. It is shown that modified sorbents based on natural bentonite are finely porous objects with a predominance of pores of 1.5−6.0 nm in size. As a result, there is a significant increase in the specific surface area of sorbents. Modification of bentonite with polyhydroxocations of iron (III) and aluminium (III) by the "co-precipitation" method also leads to an increase in the sorption capacity of the sorbents obtained with respect to nickel (II) cations. Modified bentonites were used for the adsorption of Ni (II) ions from the model solution. Ni (II) was absorbed in a neutral pH solution. The study of equilibrium adsorption showed that the data are in good agreement with the Langmuir isotherm model. The maximum adsorption capacity of the Ni (II) monolayer obtained from the Langmuir equation was 25.0 mg/g (mod. 1_Al_5-c), 18.2 mg/g (mod. 2_Al_5-c) for Al-bentonite and 16.7 mg/g (mod. 1_Fe_5-c), 10.1 (mod. 2_Fe_5-c) for Fe-bentonite. The kinetics of adsorption is considered. The high content of Al-OH anion exchange centresin them determines the higher sorption activity of Al-modified bentonites.

The very slow anodic oxygen evolution reaction (OER) greatly limits the development of large-scale hydrogen production via water electrolysis. By replacing OER with easier urea oxidation reaction (UOR), developing a HER/UOR coupling electrolysis system for hydrogen production can significantly save energy and costs. Al doped cobalt ferrocyanide (Al-Co2Fe(CN)6) nanocube array was in-situ grown on nickel foam (Al-Co2Fe(CN)6/NF). Due to the unique nanocube array structure and regulated electronic structure of Al-Co2Fe(CN)6, the as-prepared Al-Co2Fe(CN)6/NF electrode exhibited outstanding catalytic activities and long-term stability to both UOR and HER. The Al-Co2Fe(CN)6/NF electrode needed potentials of 0.169 V and 1.118 V (vs. reversible hydrogen electrode) to drive 10 mA cm−2 for HER and UOR, respectively, in alkaline condition. Applying the Al-Co2Fe(CN)6/NF to a whole urea electrolysis system, 10 mA cm−2 was achieved at a cell voltage of 1.357 V, which saved 60% electricity energy comparing to that of tranditional water splitting. Density functional theory calculations demonstrated that the boosted UOR activity comes from Co sites with Al doped electronic environments. This promoted and balanced the adsorption/desorption of main intermediates in UOR process. This work indicates that Co based materials as efficient catalysts have great prospects for application in urea electrolysis systems, and are expected to achieve low-cost and energy-saving H2 production.

The hydrogen evolution reaction (HER) has garnered attention to access sustainable energy generation with a pollutant-free combustion product in the form of H2 gas. Despite the utility of this pathway in the context of growing climate concerns, stable HER electrocatalysts which avoid the use of rare-earth platinum while retaining high catalytic performance and efficiency remains a challenge. In this work, we present the application of a binuclear nickel (II/III) Schiff base complex [Ni]2[L]2 2 for HER electrocatalysis. The design of the electrocatalyst provides optimal HER activity as the presence of electronegative heteroatoms in proximity to the metal centers augments proton affinity. As a result, the catalyst displays excellent HER activity with 100% faradaic efficiency (FE) at an onset potential of 0.4 V vs. reverse hydrogen electrode (RHE), sustained catalytic activity during prolonged electrolysis for greater than 17 hours, and provided a turn over number (TON) of 0.0006 s-1.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

Pt-coated Ni layer supported on Ni foam catalyst (denoted PtNi/Nifoam) was investigated for the oxidation of the formic acid (FAO) in acidic media. The prepared PtNi/Ni foam catalyst was studied as a function of the formic acid (FA) concentration at bare Pt and PtNi/Nifoam catalysts. The catalytic activity of the PtNi/Nifoam catalysts, studied on the basis of the ratio of the direct and indirect current peaks (jd)/(jnd) for the FAO reaction, showed values about 10 times higher compared to those on bare Pt, particularly at a low formic acid concentrations, reflecting the superiority of the former catalysts for the oxidation of FA to CO2. Ni foams provide a large surface area for the FOR while synergistic effects between Pt nanoparticles and Ni-oxy species layer on Ni foams contribute significantly to the enhanced oxidation of FA via the direct pathway, making it almost equal to the indirect pathway, particularly at low formic acid concentrations.

The creation of nano-zero-valent iron (nZVI) by implementing plant extracts is an environmentally friendly process. High antioxidant capacity and phenol content indicated the possibility of oak-nZVI synthesis using oak leaf extract as a stable material with minimal agglomeration. Simultaneously removal of Cd and phosphates and Ni and phosphates was optimized by a statistically designed experiment with a definitive screening design. In terms of significance, 4 input parameters on process productivity were monitored: initial metal concentration (1 - 9 mgL-1), initial ion concentration (1- 9 mgL-1), pH value (2 - 10) and oak-nZVI dosage (2 - 16 ml). Phosphate removal efficiency, in the presence of cadmium, was the most influenced by oak-nZVI dose and cadmium concentration, while pH gave three statistically significant interactions with oak-nZVI dosage, cadmium concentration, and phosphate concentration. Phosphate removal efficiency, in the presence of Ni, is the most influenced by nickel concentration, phosphate concentration, pH, two-factor interaction between nZVI dose and Ni concentration, and quadratic phosphate interaction. The process optimization yielded the highest simultaneous removal efficiency of 98.99% and 87.30% for cadmium and phosphate ions, respectively. Also, the highest simultaneous removal efficiency of nickel and phosphates ion was 93.44% for 96.75%, respectively. The optimization process fits into the confidence intervals, confirming the assumption that the adopted regression model describes the process well. This work demonstrated an enormous potential and prosperous application for the Cd(II), Ni(II), and phosphate removal from water matrices.

The Ni-laterite deposit at the San Felipe plateau, located 30 km northwest of Camagüey, in cen-tral Cuba, is the best example of a clay-type deposit in the Caribbean region. San Felipe resulted from weathering of mantle peridotites of the Cretaceous Camagüey ophiolites. In this study, a geochemical and mineralogical characterization of two profiles (83 and 84) from the San Felipe deposit has been performed by XRF, ICP-MS, quantitative XRPD, oriented aggregate mount XRD, SEM, FE-SEM and EMPA. Core 83 with a length of 23 m, and drilled in the central part of the plateau, presents a notable concentration of cryptocrystalline quartz fragments and a rather poor content in NiO, averaging 0.87% wt. Core 84, which is 12 m long, and drilled at the border of the plateau, lacks silica fragments and presents a higher NiO content, averaging 1.79 %wt. The smectite structural formulae reveal that they evolve from trioctahedral to dioctahedral towards the top of the laterite profiles. Quantitative XRD analyses indicate that smectite is a dominant Ni bearing phase, accompanied by serpentine and minor chlorite. Serpentine, as smectite, is en-riched in the less soluble elements Fe3+, Al and Ni towards the top of the profiles. Core 83 seems to have been affected by collapses, replenishments, whereas core 84 may have remained undis-turbed.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

In the past decade, under the background of the carbon peaking and carbon neutrality era, the rapid development of new energy vehicles has put forward higher requirements for the performance of strike forces such as battery cycle life, energy density and cost. Lithium-ion batteries have gradually become the mainstream of electric vehicle power batteries due to their excellent energy density, rate performance and cycle life. At present, the most widely used cathode materials for power batteries are lithium iron phosphate (LFP) and ternary nickel-cobalt-manganese (NCM). However, these materials exhibit the bottlenecks that limit the improvement and promotion of power battery performance. In this review, the performance characteristics, cycle life attenuation mechanism (including structural damage, gas generation and active lithium loss, etc.) and improvement methods (including surface coating and element-doping modification) of LFP and NCM batteries are reviewed. Finally, the development prospects of this field are proposed.

Nickel-based Superalloy Inconel 718 is widely used in the aerospace industry for its excellent high-temperature strength and thermal stability. However, milling Inconel 718 presents challenges due to significantly increased cutting force and vibration, which is a typical difficult-to-machine material. This paper focuses on the milling process of Inconel 718, establishing a milling force model to analyze the force trends under various processing parameters. Finite element analysis is employed to study the stress and temperature fields during milling. Dynamic equations for milling Inconel 718 are developed, and stability lobe diagrams are generated based on modal experiments. Milling experiments on Inconel 718 validate the milling force model and finite element analysis results. The fmincon optimization algorithm is utilized to identify the optimal machining parameters for Inconel 718. Through this research, valuable insights into enhancing the efficiency and quality of Inconel 718 machining are provided. This study contributes to a deeper understanding of Inconel 718 milling behavior, offering crucial guidance for more efficient machining processes.

This study presents the synthesis of graphitic carbon nitride (g−C3N4) and its nanostructures with cobalt ferrite oxide (CoFe2O4) and silver nanocubes (Ag) using the combined pyrolysis of melamine and polyol method. The resulted nanostructures were tested as electrocatalysts for hydrogen and oxygen evolution reactions in alkaline media. It was found that the Ag/CoFe2O4/g−C3N4 shows the highest current density and gives the lowest overpotential of −259 mV for HER to reach a current density of 10 mA cm−2 in 1 M KOH. Overpotentials to reach the current density of 10 mA·cm−2 for OER are 370.2 mV and 382.7 mV for Ag/CoFe2O4/g−C3N4 and CoFe2O4/g−C3N4, respectively. The above results demonstrate that CoFe2O4/g−C3N4 and Ag/CoFe2O4/g−C3N4 materials could act as a bifunctional catalyst due to the notable performance towards HER and OER and for total water splitting in practical applications is a promising alternative to noble metal-based electrocatalysts.

The selective extraction of metals from aqueous solutions is very important stage in hydrometallurgical processing of metallic waste. Leach solutions are usually a multi-component mixture. The main impurity of aqueous solutions obtained after leaching using inorganic acids is iron. In this work, the membrane separation of iron(III) from nickel(II), cobalt(II) and lithium(II) was studied. The facilitated transport of metal ion using the polymer inclusion membranes (PIMs) with tetrabutylammonium bromide (TBAB) as an ion carrier under various conditions was analyzed in detail. The several factors such as the ion carrier concentration in the membrane as well as the effect of the inorganic acids concentration in the source/receiving phases on the kinetic parameters were investigated. The results show that ionic liquid TBAB is a very selective ion carrier of Fe(III) towards Ni(II), Co(II) and Li(I) .

A conventionally cast CoNiFeMn0.5Cr1.5 alloy and two versions with 0.25C&3.7Ta or 0.25C&3.7Hf were tested in oxidation at 1000°C for 50h with thermogravimetric recording of the oxidation kinetic. In all cases the obtained mass gain curves are parabolic. Their parabolic constants are much lower than the Kp previously determined for the original alloys with an equimolar base (CoNiFeMnCr). However, the post–mortem exploitation of the oxidized samples revealed analogous oxidation features on surface and subsurface, with here too external oxide strata on surface with different Mn and Cr contents, and rather great Mn–depletion in addition to a moderate Cr–depletion, in subsurface. Globally, the oxidation behavior is significantly better than earlier observed for the equimolar version of these alloys.

The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.

A new approach to preparing a series of Co/Sm2O3 catalysts for hydrogen production by dry re-forming of methane (DRM) is developed. The catalysts precursors are synthesized by a simple method, including evaporation of aqueous solutions of cobalt and samarium nitrates, followed by a short-term calcination of the resulting material. The as-prepared and spent catalysts are characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), temperature-programmed reduction (H2-TPR), and thermogravimetric analysis (TGA). It is shown that the content of cobalt in the synthesized materials affects their phase composition and carbonization resistance in the DRM reaction. It is demonstrated that preheating under N2 affords catalysts providing stable hydrogen and CO yields of 94-98 % for at least 50 h at 900°C. These yields are among the highest ones currently available for DRM catalysts derived from Co-Sm complex oxides. It is found that reduction in the amount of cobalt in the catalyst and its preheating to an operating temperature of 900°C in a nitrogen flow con-tribute to preventing catalyst carbonization and metal particles sintering.

Urea, a prevalent component found in wastewater, shows great promise as an alternative substrate to water for energy-efficient hydrogen production by electrolysis. However, the sluggish kinetics of the anodic urea oxidation reaction (UOR) significantly hampers the overall reaction rate. To address this challenge, this article presents a comprehensive study focusing on the controlled fabrication of hierarchically structured nanomaterials as potential catalysts for UOR. The prepared MnO2@NiCo-LDH hybrid catalyst demonstrates remarkable improvements in reaction kinetics, benefiting from synergistic enhancements in charge transfer and efficient mass transport facilitated by its unique three-dimensional architecture. Notably, the catalyst exhibits an exceptionally low onset potential of 1.228 V and requires only 1.326 V to achieve an impressive current density of 100 mA cm-2, representing a state-of-the-art performance in UOR. These findings highlight the tremendous potential of this innovative material-designing strategy to drive advancements in electrocatalytic processes.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Filamentous manganese (Mn) oxide particles, which occur in the suboxic zone of stratified waterbodies, are important drivers of diverse elemental cycles. Although these particles are considered to be bacteriogenic, the environmental factor responsible for their formation has not been identified. Based on this study of laboratory cultures of a model Mn(II)-oxidizing bacterium, the supply of algal extracellular polymeric substances (EPS) was shown to stimulate Mn(II) oxidation and thus the production of filamentous Mn oxide particles. This observation was consistent with results obtained for naturally occurring particles collected from a near-bottom layer (depth of ~90 m) in the northern basin of Lake Biwa, Japan, that is, most Mn particles resembling delta-MnO2 were associated with an EPS-like gelatinous matrix, which contained dead algal cells and was lectin-stainable. In the lake water column, EPS produced by photosynthesis sank to the bottom layer. The analysis of the quality of water samples, which have been collected from the study site for 18 years, reveals that the annual average total phytoplankton biovolume in the surface layer correlates with the density of filamentous Mn particles in the near-bottom layer. Among different phytoplankton species, green algae appeared to be the key species. The results of this study suggest that algal EPS production induces the formation of filamentous Mn oxide particles in the near-bottom layer of the northern basin of Lake Biwa.

Cobalt, like other critical elements, is gaining in importance today. The great technological advances and the deep knowledge of the physical and chemical properties of this element have allowed to enhance its applications in various fields, such as: catalysts, paints, alloys for the mechanical and aerospace industries, as well as the medical sector and in recent times, its use within the rechargeable battery industry. The main exploitable deposits are in the Democratic Republic of the Congo, which have economic potential due to a strong influence on their mineralization processes. However, the growing demand for cobalt and the search for less dependence on African deposits leads to targeting other regions, so it is necessary to carry out exhaustive exploration to find out the potential of its reserves for a subsequent benefit of the mineral. Generally, cobalt comes as a by-product of the extraction of other metallic minerals, mainly from Cu-Co, Ni-Co, Ni-Cu-Co deposits. From the above, a first review is carried out on the differences that exist in the geochemical, mineralogical and forecast properties that exist within the different deposits that harbor cobalt. As a second review topic, it delves into efficient processing for cobalt recovery, which is generally carried out by flotation, acid leaching, in addition to its recovery from secondary sources, such as batteries and metallurgical waste. However, generally speaking there is still a vast lack of fundamental knowledge about the processability of cobalt. Said processing has been affected from the point of view of mineralogy, that is, understanding and knowing the cobalt-bearing minerals, as well as gangue mineralogy, these aspects exercise significant control during their processing and selection of the most appropriate route. suitable for cobalt extraction (leaching and/or flotation). In this context, the document concludes with a vision of the challenges that the mining industry must implement to enter circular economy models, mainly in the creation of sustainable processes from secondary sources.

Iron-containing nickel sulfides, selenides, and sulfoselenides were synthesized via a simple two-step hydrothermal reaction (temperature 160 °C) for their application as electrocatalysts in the oxygen evolution reaction (OER) in an alkaline solution (1 mol L–1 KOH). The study demonstrated that iron-containing nickel cobalt sulfides and selenides exhibit superior OER performance with lower overpotentials compared to iron-free nickel cobalt sulfide and selenide, which highlights the significant role of iron in enhancing OER nickel cobalt electrocatalysts: Fe0.1Ni1.4Co2.9(S0.87O0.13)4, η50 = 318 mV; Fe0.2Ni1.5Co2.8(S0.9O0.1)4, η50 = 310 mV; Fe0.3Ni1.2Co2.5(S0.9O0.1)4, η50 = 294 mV; Fe0.6Ni1.2Co2.5(S0.83O0.17)4, η50 = 294 mV, Fe0.4Ni0.7Co1.6(Se0.81O0.19)4, η50 = 306 mV compared to Ni1.0Co2.1(S0.9O0.1)4, η50 = 346 mV and Ni0.7Co1.4(Se0.85O0.15)4, η50 = 355 mV (all values at current densities η50 of 50 mA cm–2). Furthermore, the iron-containing nickel cobalt sulfoselenide Fe0.5Ni1.0Co2.0(S0.57Se0.25O0.18)4 displayed exceptional OER performance with η50 = 277 mV, surpassing the benchmark RuO2 electrode with η50 = 299 mV. The superior performance of the sulfoselenide was attributed to its low charge transfer resistance (Rct) of 0.8 Ω at 1.5 V vs. the reversible hydrogen electrode (RHE). Moreover, the sulfoselenide demonstrated remarkable stability, with only a minimal increase in overpotential (η50) from 277 mV to 279 mV after a 20 h chronopotentiometry test. These findings suggest that trimetallic iron, nickel and cobalt sulfide, selenide and especially sulfoselenide materials hold promise as high-performance, cost-effective, and durable electrocatalysts for sustainable OER reactions. This study provides a valuable approach for the development of efficient electrocatalytic materials, contributing to the advancement of renewable energy technologies.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

Additive Manufacturing and nanotechnology have been used as basic tools for the manufacture of nanostructured parts with magnetic properties to expand the variety of applications in additive processes by tank photopolymerization. Magnetic cobalt ferrite (CoFe2O4) and barium ferrite (BaFe12O19) nanoparticles with the size distribution of average value DTEM of 12 ± 2.95 nm and 37 ± 12.78 nm, respectively were generat-ed by hydroxide precipitation method. The dispersion of the nanoparticles on commercial resins (Anycubic Green and IRIX White resin) was obtained by mechanochemical reactions carried out in an agate mortar for 20 minutes, at room temperature and with limited exposure to light. The product of each reaction was placed in amber vials, also being kept in a box, to avoid contact with light. The photopolymerization process was carried out only at low concentrations (w/w % nanoparticles/resin) since, at high concentrations, there is no for-mation of pieces due to the high refractive index of ferrites. Raman shift spectroscopy of the final pieces showed that they contain the magnetic nanoparticles, with no apparent chemical changes. The EPR results of the pieces maintain the magnetic properties and apparently, they are not modified during the photopolymer-ization. Although significant differences were found in the dispersion process of the nanoparticles in each piece, we determined that the photopolymerization did not influence the structure and superparamagnetic behavior of ferrite nanoparticles during processing, and the magnetic properties were successfully transferred to the final 3D-printed magnetic obtained piece.

Co/TiO2 catalysts with different cobalt loadings (3.8, 7.5 and 15 wt%) were prepared by impreg-nation method of Co(NO3)2 .6H2O over titania. Samples containing Co(NO3)2 .6H2O and TiO2 in stoichiometric proportions in order to obtain CoTiO3 and Co2 TiO4 phases were also synthesized. The effect of the calcination treatment at two different temperatures, 550 and 1150 °C was investigated. Characterizations by several techniques, such as XRD UV-vis-NIR, DRS, Raman and XPS were carried out. XRD showed the coexistence of three phases: CoTiO3; Co2TiO4 and Co3O4 after calci-nation at 550°C, while the calcination at high temperature (1150°C) leads to single-phase systems (CoTiO3 or Co2TiO4). Diffuse reflection and XPS spectroscopy showed that divalent cobalt occupies octahedral sites in the ilmenite phase and both tetrahedral and octahedral sites in the spinel phase. The catalytic performances of the prepared catalysts, calcined at the two different temperatures, were evaluated in the oxidative dehydrogenation reaction (ODH) of ethane to ethylene. The con-version values were almost comparable for all the samples, calcined at 550 °C, and comparable the ethylene selectivity were recorded, slightly higher only in the case of CoTiO3. The calcination at 1150°C did not modify the overall activity (ethane conversion values around 20%), however, the production of COx becomes more significant. The study examined the influence of the reaction mixture composition, specifically the presence of water, and reveals a slight increase in the yield of ethylene accompanied by a decrease in the overall catalyst activity. This behavior is likely attributed to an increase in the surface concentration of hydroxyl species (OH), resulting in heightened surface acidity.

Manganese sludge, an industrial waste in the ferroalloy industry, contains various components and holds significant importance for sustainable development through its valorization. This study focuses on characterizing a manganese sludge and investigating its behavior during sulfuric acid leaching. The influence of process conditions, including temperature, acid concentration, liquid to solid ratio, and leaching duration, was examined. The results revealed that Mn, Zn, and K are the main leachable components, and their leaching rates increase with increasing temperature, liquid to solid ratio, and time. However, acid concentration requires optimization. High leaching rates of 90% for Mn, 90% for Zn, and 100% for K were achieved. Moreover, it was found that Pb in the sludge is converted to sulfate during the leaching which yields a sulfate concentrate rich in PbSO4. The leaching process for Mn and Zn species appears to follow a second or -third order reaction, and the calculation of rate constants indicated that Mn leaching kinetics are two to five times higher than those for Zn. Thermodynamic calculations were employed to evaluate the main chemical reactions occurring during leaching.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

Single-Molecule Magnets (SMMs) have attracted much interest because of their spin properties and potential technological applications. Besides, a great effort has been devoted to their functionalization, which is made with functional groups convenient to connect suitable SMMs to junction devices or to perform their grafting on surfaces of different substrates. We have synthesized and characterized two lipoic acid-functionalized and oxime-based MnIII compounds, of formula [Mn6(μ3-O)2(H2N-sao)6(lip)2(MeOH)6][Mn6(μ3-O)2(H2N-sao)6(cnph)2(MeOH)6]}·10MeOH (1) and [Mn6(μ3-O)2(H2N-sao)6(lip)2(EtOH)6]·EtOH·2H2O (2) [H2N-saoH2 = salicylamidoxime, lip = lipoate anion, cnph = 2-cyanophenolate anion]. 1 crystallizes in the triclinic system with space group Pī and 2 crystallizes in the monoclinic system with space group C2/c. In their crystal packing, adjacent Mn6 complexes are connected through non-coordinating solvent molecules, which are H-bonded to N atoms of –NH2 groups of salicylamidoxime ligand. In addition, Hirshfeld surfaces of 1 and 2 were calculated to study the variety of intermolecular interactions and different level of importance that take place in their crystal lattice, this type of computed study being the first time performed on Mn6 molecules. The study of the magnetic properties of 1 and 2 through dc magnetic susceptibility measurements reveals the coexistence of ferro- and antiferromagnetic exchange couplings between the Mn(III) metal ions in both compounds, the latter being the predominant magnetic interaction. A ground state spin value of S = 4 was obtained through isotropic simulations of the experimental magnetic susceptibility data for both 1 and 2. Ac magnetic susceptibility measurements show the occurrence of slow relaxation of the magnetization in 1 and 2, which indicate that SMM behavior take place in both compounds.

Abstract: Interactions in multicomponent Ni-Cr-Mo-Al-Re model alloy were determined by ab initio calculations in order to investigate the Re doping effect on Haynes 282 alloy. Simulation results provided an understanding of short-range interactions in the alloy and successfully pre-dicted the formation of a Cr and Re-rich phase. The Haynes 282 + 3 % wt. Re alloy was manu-factured using the additive manufacturing Direct Metal Laser Sintering (DMLS) technique, in which the presence of the (Cr17Re6)C6 carbide was confirmed by an XRD study. The results ob-tained provide useful information about the interactions between Ni, Cr, Mo, Al, and Re as a function of temperature. The 5-element model designed can lead to a better understanding of phenomena that occur during the manufacturing or heat treatment of modern, complex, multi-component Ni-based superalloys.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

The CYSTM (cysteine-rich transmembrane module) protein family comprises small molecular cysteine-rich tail-anchored membrane proteins found in many eukaryotes. The Saccharomyces cerevisiae strains carrying the CYSTM genes YDRO34W-B and YBR056W-A (MNC1) fused with GFP were used to test expression of these genes under different stresses. The YBR056W-A (MNC1) and YDR034W-B genes are expressed under stress conditions caused by the toxic concentrations of heavy metal ions such as manganese, cobalt, nickel, zinc, cuprum, and 2.4-dinitrophenol uncoupler. YDR034W-B but not YBR056W-A is expressed under alkali and cadmium stresses. YBR056W-A is localized in intracellular membranes, while YDR034W-B is localized in the cytoplasmic membrane. The null-mutants in both genes demonstrated both decreased cell concentration and lytic phenotype when cultivated in the presence of excess manganese. This indicates the involvement of Mnc1 and YDR034W-B proteins in manganese detoxification, probably by complexation of its ion.

In this work, we report manganese phthalocyanine (MnPc) films obtained by ultrasonic spray-pyrolysis technique at 40°C deposited on glass substrate subjected to thermal annealing at 100 °C and 120°C. The MnPc films were characterized by UV/Vis spectroscopy, Raman spectroscopy, X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The absorption spectra of the MnPc films were studied in a wavelength range from 200 to 850 nm, where the characteristic bands of a metallic phthalocyanine known as B and Q bands were observed in this range of the spectrum. The optical energy band (Eg) was calculated by the Tauc equation. It was found that for these MnPc films, the Eg has the values of 4.41, 4.46 and 3.58 eV corresponding to as deposited, annealing 100°C and 120°C, respectively. The Raman spectra of the films showed their characteristic vibrational modes of the MnPc films. In X-ray diffractograms of these films, the characteristic diffraction peaks of a metallic phthalocyanine are observed, presenting a monoclinic phase. SEM images of these films were studied in cross section obtaining thicknesses of 2, 1.2 and 0.3 μm to as deposited, annealing 100°C and 120°C, successively. Also, in the SEM images of these films, both the average particle sizes ranging from 4 to 0.041 µm and the average diameter from 4.8 to 0.091 μm were obtained. The results agree with those reported in the literature for MnPc films deposited with other techniques.

Metal-organic frameworks (MOFs) are investigated for the oxygen evolution reaction (OER) due to their structure diversity, high specific surface area, adjustable pore size and abundant active sites. However, the poor conductivity of most MOFs restricts this application. Herein, through a facile one-step solvothermal method, the Ni-based pillared metal-organic framework [Ni2(BDC)2DABCO] (BDC = 1,4-benzenedicarboxylate, DABCO = 1,4-diazabicyclo[2.2.2]octane), its bimetallic nickel-iron form [Ni(Fe)(BDC)2DABCO] and their modified Ketjenblack (mKB) composites were synthesized and tested towards OER in an alkaline medium (KOH 1 mol L–1). A synergistic effect of the bimetallic nickel-iron MOF and the conductive mKB additive enhance the catalytic activity of the MOF/mKB composites. All MOF/mKB composite samples (7, 14, 22, 34 wt.% mKB) indicated much higher OER performances than the MOFs and mKB alone. The Ni-MOF/mKB14 composite (14 wt. % of mKB) demonstrated an overpotential of 294 mV at a current density of 10 mA cm–2 and Tafel slope of 32 mV dec–1, which is comparable with commercial RuO2 commonly used as a benchmark material for OER. The catalytic performance of Ni(Fe)MOF/mKB14 (0.57 wt% Fe) was improved further to an overpotential of 279 mV at a current density of 10 mA cm–2. The low Tafel slope of 25 mV dec–1 as well as a low reaction resistance due to electrochemical impedance spectroscopy (EIS) measurement confirm the excellent OER performance of the Ni(Fe)MOF/mKB14 composite. For practical applications, the Ni(Fe)MOF/mKB14 electrocatalyst was impregnated into commercial nickel foam (NF), where overpotentials of 247 and 291 mV at current densities of 10 and 50 mA cm–2, respectively, were realized. The activity was maintained for 30 h at the applied current density of 50 mA cm–2. The electrocatalytic system consisting of earth-abundant Ni and Fe metals only would be attractive for the development of efficient, practical and economical energy conversion materials for efficient OER activity.

The exploitation of the metallacarboranes’ potential in various fields of research and practical ap-plications requires the availability of convenient and versatile methods for their functionalization with various functional moieties and/or linkers of different types and lengths. Herein we report a study on cobalt bis(1,2-dicarbollide) functionalization at 8,8’-boron atoms with different het-ero-bifunctional moieties containing protected hydroxyl function allowing further modification after deprotection. Moreover, an approach to the synthesis of three and four functionalized metallacarboranes, at boron and carbon atoms simultaneously, via additional functionalization at carbon to obtain derivatives carrying three or four rationally oriented and distinct reactive surfaces, is described

Abstract: Five patients with standard medical treatment-resistant symptoms of skin lesions, ear infections, allergic rhinitis, nasal congestion, asthma, heartburn, and failure to thrive were success- fully treated with an integrative medicine assessment and integrative medicine treatment approach. The integrative medicine assessment method of autonomic response testing enabled the identifica- tion of nickel sensitivity as a common element in these patients. It guided the use of the integrative medicine therapies of low dose immunotherapy, gamma linoleic acid supplementation, chelation, dietary nickel restriction, and removal of nickel containing dental and cosmetic appliances. A chart review of 151 patients indicated a strong association of nickel and the simultaneous presence of skin lesions.

Immobilized metal affinity chromatography (IMAC) is a popular and valuable method for the affinity purification of polyhistidine-tagged recombinant proteins. However, it often shows practical limitations, which might require cumbersome optimizations, additional polishing, and enrichment steps. Here, we present functionalized corundum particles for the efficient, economical, and fast purification of recombinant proteins in a column-free format. The corundum surface is first derivatized with the amino silane APTES, then EDTA dianhydride, and subsequently loaded with nickel ions. The Kaiser test, well-known in solid-phase peptide synthesis, was used to monitor amino silanization and the reaction with EDTA dianhydride. In addition, ICP-MS was performed to quantify the metal-binding capacity. His-tagged protein A/G (PAG), mixed with bovine serum albumin (BSA), was used as a test system. The PAG binding capacity was around 3 mg protein per gram of corundum. Cytoplasm obtained from different E. coli strains was examined as an example of a complex matrix. The imidazole concentration was varied in the loading and washing buffers. As expected, higher imidazole concentrations during loading are usually beneficial when higher purities are desired. Even when higher sample volumes, such as one liter, were used, recombinant protein down to a concentration of 1 µg/mL could be isolated selectively. Comparing the corundum material with standard Ni-NTA agarose beads indicated higher purities of proteins isolated using corundum. His6-MBP-mSA2, a fusion protein consisting of monomeric streptavidin and maltose-binding protein in the cytoplasm of E. coli, was purified successfully. To show that this method is also suitable for mammalian cell culture supernatants, purification of the SARS-CoV-2-S-RBD His8 expressed in human Expi293F cells was performed. The material cost of the nickel-loaded corundum material (without regeneration) is estimated to be less than 30 cents for 1 gram of functionalized support or 10 cents per milligram of isolated protein. Another advantage of the novel system is the corundum particles' extremely high physical and chemical stability. The new material should be applicable in small laboratories and large-scale industrial applications. In summary, we could show that this new material is an efficient, robust, and cost-effective purification platform for the purification of His-tagged proteins, even in challenging, complex matrices and large sample volumes of low product concentration.

The innate immune system is the first line of host defense sensing viral infection. Manganese (Mn) has recently been found to be involved in the activation of innate immune DNA sensing cGAS-STING pathway and subsequent anti-DNA virus function. However, whether Mn2+ mediates host defense against RNA viruses is still unclear. In the current study, we demonstrated that Mn2+ exhibited antiviral effects against various animal and human viruses including RNA viruses such as PRRSVs and the VSV as well as a DNA virus such as the HSV1 in a dose-dependent manner. Moreover, cGAS and STING were both investigated in the Mn2+ mediated antiviral roles using the knockout cells made by CRISPR-Cas9 approach. Unexpectedly, the results revealed that neither cGAS knockout nor STING knockout had any effect on Mn2+ mediated antiviral functions. Nevertheless, we verified that Mn2+ promoted the activation of cGAS-STING signaling pathway. These findings suggest that Mn2+ has broad spectrum antiviral activities in a cGAS-STING pathway independent manner. This study also provides significant insights into redundant mechanisms participating in the Mn2+ antiviral functions and also indicates new target for Mn2+ antiviral therapeutics.

Background: Gingival enlargement is defined as an abnormal overgrowth of gingival tissues. A case of a 34–year–old female presenting with maxillary chronic inflammatory gingival enlargement associated with a nickel wire allergy is reported here. Replacement of the wire, good oral hygiene therapy and surgical therapy was carried out to provide a good aesthetic outcome. Histopathological evaluation was done of the excised specimen. There is only one similar case reported in literature to the best of our knowledge and ours is the second case. Result: A Histopathological diagnosis of inflammatory fibrous hyperplasia was established. No recurrence was reported at the end of 1 year. Conclusion: The patient should be made aware of the allergy at the initial visit and oral hygiene instructions should be reinforced at every visit. The significance of patient compliance during and following therapy as an important factor in the success of treatment.

The application of diffusion dialysis using various types of ion-exchange membranes for the separation of sulfuric acid and nickel sulfate has been evaluated. The process of dialysis separation of a real waste solution from an electroplating facility containing 252.3 g/L of sulfuric acid, 20.9 g/L of nickel ions and small amounts of zinc, iron, copper ions, etc. has been studied. Heterogeneous cation-exchange membrane containing sulfo groups and heterogeneous anion-exchange membranes with different thicknesses (from 145 μm to 550 μm) and types of fixed groups (4 samples with quaternary amino groups and 1 sample with secondary and tertiary amino groups) are used. The diffusion fluxes of sulfuric acid, nickel sulfate, and the total and osmotic fluxes of the solvent are determined. The use of a cation-exchange membrane does not allow separation of the components, since the fluxes of both components are low and comparable in magnitude. The use of anion-exchange membranes makes it possible to efficiently separate sulfuric acid and nickel sulfate. At the same time, the thin dialysis membrane turns out to be the most effective, as well as the membranes with quaternary amino groups, and the membrane with secondary and tertiary amino groups proved to be the least effective.

Lithium-ion (Li-ion) batteries are becoming more common in portable electronic devices due to their high energy density, lack of memory effect, and high charge and discharge rate capabilities. Li-ion batteries are a relatively new technology, first marketed in the early 1990s, and research and development work are ongoing to improve safety and increase capacity, charge/discharge rate, and lifetime [1]. In this paper, we review the types and characteristics of Li-ion batteries and summarize charging methods and safety considerations. Following, we design and fabricate Li-ion battery and highlight the steps of fabrication that ensure fast charge/discharge rates that give the battery more reliability and high energy density

Nickel foam substrates are frequently utilised for renewable energy applications as porous 3D-substrates. Preparation of these substrates usually includes an acid washing step, however the degree to which this step affects the final electrochemical performance after spray coating a catalyst ink is unreported. Herein, we report the effect of acid washing through physicochemical and electrochemical characterisation. The electrochemical performance was determined by repeated measurements of catalyst-coated nickel foam substrates both with and without the initial step of acid washing. Acid washing increased current density by 17.9% for the acid treated, MoS2-coated nickel foam electrode. This increment was affiliated with an electrochemically active surface area which increased by 87.1%, where Tafel analysis indicated that the acid treated, MoS2-coated electrodes facilitates the initial water dissociation step of the hydrogen evolution reaction with greater ease. Similar effects were also discovered for acid treated PtIr(1:3)/C-coated nickel foam substrates, albeit with less pronounced effects. Stability was also improved where the degradation rate was reduced by 18.9% for the acid treated, MoS2-coated electrodes. This proves the utility of acid washing nickel foam electrodes.

The integration of metal nanoparticles and solid carriers can achieve ideal stability, high load and good conductivity. In this work, copper nanoparticles (Cu NPs) were sequentially deposited on a cobalt metal-organic framework (Co-MOF) by bonding with exposed imino groups, followed by a reduction reaction to prepare a new Cu@Co-MOF composite. Cu@Co-MOF acts as a non-enzymatic electrochemical sensor to detect glucose (Glu) in an alkaline medium. The composite working electrode of Cu@Co-MOF/GCE (GCE = glassy carbon electrode) improves the electrocatalytic activity for Glu oxidation. Cu@Co-MOF/GCE shows excellent electrocatalytic performances in Glu concentration ranging 0.005~1.8 mmol∙L⁻¹ (mM): the sensitivities are 282.89 μA∙mM⁻¹∙cm⁻² in 0.005-0.4 mM Glu and 113.15 μA∙mM⁻¹∙cm⁻² in 0.4-1.8 mM Glu respectively with low detection limit of 1.6 μM (S/N = 3) and high selectivity and stability.

The reaction of [Co2(CO)8] with an equimolar amount of P(OPh)3] in toluene solution yields in situ generated [Co2(CO)7{P(OPh)3}] 1. Subsequent heating of 1 provides in a condensation reaction an alternative synthetic access to the tetranuclear cluster [{Co4(μ2-CO)3(CO)8{P(OPh)3}] 2. Compound 2 has been characterized by IR and 31P NMR spectroscopy, the tetranuclear cluster framework has be ascertained by a single-crystal X-ray diffraction study performed at 100 K.

The development and improvement of methods for the synthesis of environmentally friendly catalysts based on base metals is currently an urgent and promising task of modern catalysis. Catalysts based on nanoscale magnetite and maghemite have fast adsorption-desorption kinetics and high chemical activity. The purpose of this work was to obtain magnetic composites, determine their physicochemical characteristics and verify their activity in the process of liquid-phase oxidation of phenol with oxygen. Magnetic nanocomposites were obtained by chemical co-deposition of salts of ferrous and trivalent iron. The synthesized magnetic composites were studied by X-ray diffractometry, energy dispersive X-ray fluorescence and Mössbauer spectroscopy, IR-Fourier spectroscopy, elemental analysis. To increase the catalytic activity in oxidative processes, the magnetite surfaces were modified using cobalt nitrate salt. Further, CoFe2O4 was stabilized by adding polyethylenimine (PEI) as a surfactant. Preliminary studies of the oxidation of phenol with oxygen, as the most typical environmental pollutant were carried out on the obtained Fe3O4, CuFe2O4, CoFe2O4/PEI catalysts. The spectrum of the reaction product shows the presence of CH in the aromatic ring and double C=C bonds, stretching vibrations of the C=O groups of carbonyl compounds; the band at 3059 cm–1 corresponds to the presence of double C=C bonds, the band at 3424 cm–1 hydroquinone compounds. The band at 1678 cm–1 and the intense band at 1646 cm–1 refer to vibrations of the С=О bonds of the carbonyl group of benzoquinone. Peaks at 1366 cm–1 and 1310 cm–1 can be related to the vibrations of C–H and C–C bonds of the quinone ring. Thus it was demonstrated that produced magnetic composites based on iron oxide are quite effective in the oxidation of phenol with oxygen.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

White-rot fungi (WRF) have specific enzymes to degrade lignocellulosic and phenolic compounds. Therefore, their direct application could be an alternative to biodegrade complex lignocellulosic biomass such as olive mill solid waste (OMSW). The aim of this study was to evaluate the capacity of A. discolor and S. hirsutum to grow in OMSW as the sole substrate under static conditions and evaluate the phenolic removal compounds and lignin degradation. The lignolytic enzyme activity was determined, as was the phenolic compound removal. At the same time, lignin degradation and structural changes were evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscope (SEM), respectively. Both strains were able to grow using OMSW as the sole substrate without adding other nutrients, oxygen and/or agitation. The higher ligninolytic enzyme activity was found at day 8, and the highest phenolic removal (more than 80% with both strains) was reached after 24 days of incubation. The CLSM analysis confirmed lignin degradation through the drop in lignin fluorescence from 3967 for untreated OMSW to 235 and 221 RFU after 24 days of treatment by A. discolor and S. hirsutum respectively. The results indicate that both WRF could be suitable candidates to design an in-situ pretreatment step of OMSW, as long as in future research the WRFs have the same performance in non-sterile conditions.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

While there are extensive studies on the mineralogy and geochemistry of laterites worldwide, the temporal and spatial mineralogical development of a typical nickel laterite profile is still poorly constrained. In this study, we present a detailed mineralogical and geochemical characterization of samples systematically collected from a nickel laterite profile at the Sta. Cruz nickel laterite deposit, Zambales, Philippines, to describe the temporal and spatial development of the laterite profile. Wavelength-dispersive X-ray fluorescence spectroscopy (WDSXRF), mass balance-element mobility calculations, transmitted and reflected light microscopy, and previously reported results from coupled X-ray diffraction (XRD) and Rietveld refinement analyses, reveal that the laterite profile investigated is composed of two main horizons: the limonite and saprolite zones, separated by a thin transitional zone. The main zones are further subdivided into subzones based primarily on the mineral assemblage and major element chemistry: upper limonite, lower limonite, transitional zone, upper saprolite, and lower saprolite. Late-stage Ni-rich serpentine veins were observed cutting the upper and lower saprolite subzones. Investigation of the structure of goethite within the limonite zone via Rietveld refinement show that the crystallinity of goethite decreases with increasing Ni content and increasing crystallite size. This suggests that upwards through the limonite zone, as goethite ages, its crystallinity increases which possibly results in the removal of Ni from its crystal structure and eventual remobilization to the lower laterite zones. We propose a genetic model of the formation of the Sta. Cruz laterite consisting of four stages: (1) early-stage alteration, (2) continued serpentinization and volume expansion, (3) late stage serpentinization, dissolution, and incipient oxide formation, and (4) goethite ageing and Ni-rich serpentine vein formation. Overall, our results suggest that serpentinization is an important aspect of Ni laterite formation, both before and after the emplacement of the peridotite protolith.

Current hydrogen production is based on the reforming process leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. Production of green hydrogen from water electrolysis using intermittent sources (e.g., solar, eolic) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for efficient nickel-based electrocatalysts. For these reasons, herein, a review of recent progress is presented.

The development of gamma rays mutant rice lines would be a solution for introducing variability in already farmer using varieties. In vitro gamma (60Co) mutagenesis reduces chimeras and allows a faster selection of desired traits but requires laboratory process optimization. The objective of the present work was the in vitro establishment of a recalcitrant rice embryogenic calli, the determination of its sensitivity to gamma radiation (Co-60), sequencing MATK and Rubisco for identification purposes, as well as generation optimization. The radiosensitivity of embryogenic calli resulted in an LD50 of 110Gy, while the 20% lethal dose was 64Gy. All sequenced genes matched perfectly with already reported MATK and Rubisco O. sativa genes with a clear SNP that identifies the local variety related to the southeast Asia Region. Callus induction improves with an MS with 2mg/L 2,4D, and the regeneration was achieved with an MS medium with 3mg/L BAP and 0,5mg/L NAA. The optimized radiation condition was 60Gy with an 83% regeneration in a semisolid medium, allowing a balance between mutation and regeneration. When increased to 80Gy, the regeneration rate falls to 29%. An immersion system (RITA®) of either 60 or 120 seconds every 8hours allowed a systematic and homogeneous total regeneration of the recalcitrant line, in contrast with the semisolid medium that resulted in positive but irregular regeneration. Other well-known recalcitrant cultivars, CR1821, CR1113 also had an improving regeneration in the immersion system, demonstrating its potential use for recalcitrant materials. To our knowledge, this is the first report on using an immersion system to allow regeneration of gamma-ray mutants from recalcitrant rice materials.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

The transport of iron(III) from Fe(III)-Mn(II)-HCl mixed solutions through a flat-sheet supported liquid membrane is investigated, being the carrier phase of Cyanex 923 (commercially available phosphine oxide extractant) dissolved in Solvesso 100 (commercially available diluent), as a function of hydrodynamic conditions, concentration of manganese and HCl in the feed phase, and carrier concentration in the membrane phase. A transport model is derived that describes the transport mechanism, consisting of diffusion through a feed aqueous diffusion layer, a fast interfacial chemical reaction, and diffusion of the Fe(III)-Cyanex 923 complex across the membrane phase. The membrane diffusional resistance (Δm) and feed diffusional resistance (Δf) are calculated from the model, and their values are 145 s/cm and 361 s/cm, respectively. It is apparent that the transport of iron(III) is mainly controlled by diffusion through the aqueous feed boundary layer, being the thickness of this layer calculated as 2.9x10-3 cm. Since Mn(II) is not transported through the membrane phase, the present system allows to the purification of this manganese-bearing solutions.

Aquatic animals have unique physiological mechanisms to absorb and retain minerals from their diets and water. Research and development in the area of mineral nutrition of farmed fish and crustaceans have been relatively slow and major gaps exist in the knowledge of trace element requirements, physiological functions and bioavailability from feed ingredients. Quantitative dietary requirements have been reported for three macroelements (calcium, phosphorus and magnesium) and six trace minerals (zinc, iron, copper, manganese, iodine and selenium) for selected fish species. Mineral deficiency signs in fish include reduced bone mineralization, anorexia, lens cataracts (zinc), skeletal deformities (phosphorus, magnesium, zinc), fin erosion (copper, zinc), nephrocalcinosis (magnesium deficiency, selenium toxicity), thyroid hyperplasia (iodine), muscular dystrophy (selenium) and hypochromic microcytic anaemia (iron). An excessive intake of minerals from either diet or gill uptake causes toxicity and therefore a fine balance between mineral deficiency and toxicity is vital for aquatic organisms to maintain their homeostasis either through increased absorption or excretion. Release of minerals from uneaten or undigested feed and from urinary excretion can cause eutrophication of natural waters, which requires additional consideration in feed formulation. The current knowledge in mineral nutrition of fish is briefly reviewed.

This paper seeks to examine how the Mn-Co spinel interconnect coating microstructure can in-fluence the Cr contamination in an oxygen electrode of intermediate temperature Solid Oxide Cells at the operating temperature of 750 °C. A Mn-Co spinel coating is processed on Crofer 22 APU substrates by electrophoretic deposition and subsequently sintered following both the one-step and two-step sintering, in order to obtain significantly different densification levels. The electrochemical characterization is performed on anode supported cells with a LSCF cathode. The cells were aged prior to the electrochemical characterization in contact with the spinel coated Crofer 22 APU at 750 °C for 250 hours. Current-voltage and impedance spectra of the cells were measured after the exposure with the interconnect. Post-mortem analysis of the interconnect and the cell was carried out in order to assess the Cr retention capability of coatings with different microstructures.

Nickel-based superalloys are attractive to many industrial sectors (automotive, military, energy, aerospace etc.). However, their physical properties make them difficult to machining using traditional tools. Therefore, the new materials for the machining of Ni-based alloys are required. Ceramic-based composites could act as a tool to replace the current materials. The incentives for this paper are to provide an overview of existing ceramic composites and draw some conclusions that will help in solving the problem of choosing materials for processing of Ni-based superalloys. Despite the diversity of ceramic composites in this work the focus was on the SiAlON ceramic.

CoCr2O4 and doped lithium Co1-xLixCr2O4 chromate powder and nanoparticles were prepared by modified by sol-gel method. The morphological and structural properties of nano chromates were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and Photoluminescence (PL). Nanoparticles of doped lithium were synthesized by adding appropriate amount of cobalt nitrate, chromium nitrate, lithium nitrate and 1,2 Ethanediol as a complexing agent. The sample were heated at 105 ˚C for ten hours in oven to obtain dry gel. Calcination temperature for these samples was 700˚C for 3 hours in a furnace. The particle size of parent compound ranges from 4.4 nm to 11 nm, determined by SEM. The tendency of particles to form the aggregates with the increased annealing temperature was observed. The SEM and optical characterization of this compound has shown the sol gel derived material may be successfully used as an effective doped lithium cobalt ceramic pigment with controlled variation in structural and optical properties. SEM images showed that spherical like doped particle have diameter 33nm. From PL spectra Nano structure shows band gap 2.5ev and when we doped Lithium in it band gap decreases and become 1.19ev, which is associated to band gap transition.

In recent years cultivated soils have been increasingly supplemented with nutrients that at low doses are necessary for proper plant functioning but become toxic at high doses. New methods are needed to prevent these destructive actions, and for this reason we studied the effects of two elements – Mn treated as a stressor and Se treated as a potential defense in two wheat cultivars. The intensity of stress was manifested in tissue browning and weight reduction and was determined by an increase in lipid peroxidation and quantitative analysis of hydrogen peroxide levels. It was found that the excess of Mn in the substrate caused more intense changes in these indicators in the root system than in the leaves, and that Se presence partly eliminated the stress evoked effects. Moreover, Mn-treatment was accompanied by a greater absorption of this element by the roots, and a reduced uptake of other elements (K, Fe, S, P), with the exception of Ca, an increase in which was observed especially in the additional presence of Se. It was suggested that the rise in Ca level can lead to modification of cell differentiations and may be one of the steps in defense mechanisms. The change in the direction of cell differentiation in the apical part of the root was observed microscopically under Mn stress and was accompanied by a quantitative increase in 5-met C. Based on DNA methylation profiles detected by MSAP we concluded that various types of methylation sites may be activated under Mn treatment in roots.